Avenview SW-HDM3D-C6-8x8E Specifications

Avenview SW-HDM3D-C6-8x8E Specifications
8x8 HDMI Matrix Switch over Single CAT5/6
With Deep Color & 3D Support
Model #: SW-HDM3D-C6-8x8E
Model #: HDM3D-C6SW-R
© 2012 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties with
respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any
time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in
Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products
including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
Reproduction of this manual, or parts thereof, in any form, without the express written permission of Avenview Inc. is strictly prohibited.
www.avenview.com|1
Table of Contents
Section 1: Getting Started ............................................................................................................................................. 3
1.1
Important Safeguards ................................................................................................................................ 3
1.2
Safety Instructions....................................................................................................................................... 3
1.3
Regulatory Notices Federal Communications Commission (FCC)........................................... 4
1.4
Introduction ................................................................................................................................................... 4
1.5
Package Contents ......................................................................................................................................... 5
1.6
Before Installation ....................................................................................................................................... 5
1.7
Panel Description ......................................................................................................................................... 6
1.7.1 SW-HDM3D-C6-8x8E Front Panel........................................................................................................ 6
1.7.2 SW-HDM3D-C5-8x8E Rear Panel ......................................................................................................... 6
1.7.3 HDM3D-C6SW-R.......................................................................................................................................... 7
1.8
IR Control Patch............................................................................................................................................ 8
HDM3D-C6SW-R ..................................................................................................................................................... 8
1.9
Installation (SW-HDM3D-C6-8x8E) ..................................................................................................... 9
1.10
Operation and IR Control........................................................................................................................ 10
1.11
RS232 Serial Port Control....................................................................................................................... 12
1.11 EDID Learning ............................................................................................................................................. 21
Section 2: Specifications ............................................................................................................................................. 22
Section 3: IR Remote User Guide ............................................................................................................................. 23
www.avenview.com|2
Section 1: Getting Started
1.1
Important Safeguards
Please read all of these instructions carefully before you use the device. Save this manual for future
reference.
What the warranty does not cover











1.2
Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
Repair or attempted repair by anyone not authorized by us.
Any damage of the product due to shipment.
Removal or installation of the product.
Causes external to the product, such as electric power fluctuation or failure.
Use of supplies or parts not meeting our specifications.
Normal wear and tear.
Any other causes which does not relate to a product defect.
Removal, installation, and set-up service charges.
Safety Instructions
The Avenview SW-HDM3D-C6-8x8E HDMI Matrix Switch over Single CAT6 with Full 3D Support and Ethernet
has been tested for conformance to safety regulations and requirements, and has been certified for
international use. However, like all electronic equipment’s, the SW-HDM3D-C6-8x8E should be used with care.
Read the following safety instructions to protect yourself from possible injury and to minimize the risk of
damage to the unit.
Do not dismantle the housing or modify the module.
Dismantling the housing or modifying the module may result in electrical shock or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing housing may expose you to
dangerous voltage or other hazards
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid
falls or spills on to the housing, unplug the module immediately.
Have the module checked by a qualified service engineer before using it again.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.
www.avenview.com|3
1.3
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this
equipment.
1.4
Introduction
The Avenview SW-HDM3D-C6-8x8E, HDMI Matrix with IR, Full 3D Support and now Ethernet over Single CAT6
provides the most flexible and cost effective solution in the market to route high definition video sources plus
multi-channel (up to 7.1 channel) digital audio from any of the eight HDMI sources to the remote displays at
the same time. Through low cost Cat-5/5e/6 LAN cables, not only high quality video and audio can be
transmitted to the display sites, but also users can switch among eight HDMI sources using the push-in button
or remote control. With single power design at the source site, each remote module is easily installed without
power supply. Furthermore, the built-in IR extension function, users can control the HDMI source devices
such as Blu-ray Disc Player, Satellite Receivers etc. at display site directly.
-
Supports HDMI Deep Color & Full 3D
HDCP compliant
Allows any source to be displayed on multiple displays at the same time
Allows any HDMI display to view any HDMI source at any time
Supports 7.1 channel digital audio
Supports default HDMI EDID and learns the EDID of displays
The matrix master can switch every output channels to any HDMI inputs by push-in button, IR remote
control, or RS-232 control
Allows controlling local HDMI sources such as DVD and TiVo by attached IR extender from remote
receiver to matrix master
Allows to control matrix master through IR remote control at remote receiver’s site
Extends video signal up to 35m (115 feet) over CAT5e at 1080p and likely longer with better HDMI
source device, better grade HDMI display, and better quality solid CAT6 cable
Easy installation with rack-mounting and wall-mounting designs for master and receiver respectively
Fast response time – 2~5 seconds for channel
Ethernet Control
www.avenview.com|4
1.5
Package Contents
Before you start the installation of the MARTIX SWITCHER please check the package contents.
-
SW-HDM3D-C5-8x8E
HDM3D-C5SW-R
IR Blaster
IR Receiver
IR Remote Control
Rackmounting Ear
Power Cable
x1
x4
x1
x5
x1
x2
x1
-
User’s Manual
x1
Software CD
x1
1.6




Before Installation
Put the product in an even and stable location. If the product falls down or drops, it may cause an
injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high
humidity.
Use the DC power adapter with correct specifications. If inappropriate power supply is used then it
may cause a fire.
Do not twist or pull by force ends of the UTP cable. It can cause malfunction.
www.avenview.com|5
1.7
Panel Description
1.7.1 SW-HDM3D-C6-8x8E Front Panel
1.
SOURCE STATUS: Input source indicator LED
2.
3.
Output Push Button & 7-segment LED:
Front panel push buttons used to select the
number of display channel & LED display for
output ports
4.
IR SENSOR: IR sensor for receiving the IR
commands from IR remote
Input Push Button & 7-segment LED:
Front panel push buttons used to select the
number of input source & LED display for
input channels
1.7.2 SW-HDM3D-C5-8x8E Rear Panel
5.
+5V DC: 5V DC power jack
7.
RS-232: RS-232 control port
All IR Output: 3.5mm IR blaster socket for
HDMI source control on all 8 inputs
11. IR Blaster 1-8: 3.5mm IR blaster socket for
individual HDMI source control
9.
6.
ETHERNET: Ethernet control port
8.
SYSTEM IR RECEIVER: Ext. IR receiver
10. INPUT 1-7: HDMI inputs
12.
INPUT 8 & EDID Port: HDMI input & EDID
port for learning EDID from display
13. OUTPUT PORT 1-4: RJ-45 outputs for each output channel
www.avenview.com|6
1.7.3 HDM3D-C6SW-R
1. SIGNAL LEVEL: Adjust the 8-level equalization
2. HDMI OUTPUT: Connect to HDTV with a HDMI cable
3. IR RECEIVER: Plug in IR receiver
4. IR BLASTER: Plug in IR blaster
5. +5V DC: 5V DC power jack
6. HDMI SIGNAL IN: Plug in a Cat.X cable
Signal Level (Signal Level 0 – 7)
Adjust the 8-level equalization control to the received HDMI signals. The HDMI signal level varies from 0
(strongest) to 7 (weakest) for respective transmission length from longest possible range to short distance.
Please adjust the signal level from 7 to 0 and stop turning the rotary switch whenever the audio/video is
playing normally. Inappropriate signal level setting may cause overpowering issue that would shorten the
product life significantly!
www.avenview.com|7
Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check
carefully before plugging in the IR extender to the respective IR sockets. Warranty will not cover the
damage.
1.8
IR Control Patch
IR Blaster Cable
IR Receiver Cable
IR Sockets
SW-HDM3D-C6-8x8E
All IR Out: The default location for IR blaster to transmit all IR command signals received from any of the
four remote receivers to all of the HDMI sources.
IR BLASTER 1-4: IR blaster connected here can only transmit IR command signals from the remote
receivers that are setting at respective input channel from 1 to 4.
System IR: Receives IR commands from remote control
HDM3D-C6SW-R
IR BLASTER: IR control on individual display device
IR RECEIVER: IR receiver connected here can receive all IR command signals from the IR remote controls of
SW-HDM3D-C6-8x8E and all other HDMI source devices.
IR Blaster
IR Receiver
www.avenview.com|8
1.9
Installation (SW-HDM3D-C6-8x8E)
To setup Avenview SW-HDM3D-C6-8x8E follow these steps for connecting to a device:
Matrix Switch
1.
2.
3.
4.
5.
6.
Connect all sources to HDMI Inputs on the Matrix Switch (SW-HDM3D-C6-8x8E)
Connect each HDMI CAT 5/6 output on the SW-HDM3D-C6-8x8E to respective CAT 5/6 input on the
remote receiver HDM3D-C6SW-R
Connect IR BLASTER cable to the SW-HDM3D-C6-8x8E and direct the IR emitter to the build-in IR receiver
of the sources
Connect the +5V 6A DC power supply to the SW-HDM3D-C6-8x8E
Power on all HDMI sources
Power on the SW-HDM3D-C6-8x8E
Receiver
1.
2.
3.
4.
Connect each HDMI output to HDMI displays.
Connect the CAT5E/6 INPUT on the HDM3D-C5SW-R to the CAT5E/6 OUTPUT port on the
SW-HDM3D-C6-8x8E.
Connect IR receiver and place the IR receiver at the appropriate position that can receive the IR command
signals sent from the users.
Dial the 8-level rotary control switch to adjust the HDMI signal level until the picture and sound are clear.
It is recommended to dial from 7 to 0 to find the optimal visual experience.
www.avenview.com|9
1.10 Operation and IR Control
Preset
Save
Learn
Default
1.10.1 Method A: Push Button
1. IN/OUT MAP
1) Use the “+”or “-“ output push button to select the number of display
2) Use the “+”or “-“ input push button to select the number of input source
“+”: change selected input/output port in ascending order
“-” : change selected input/output port in descending order
After you select the desired input/output port, the LED will blink twice and the setting will be effective
2. Save Mapping Mode
1) Keep pushing “output+ (save)”button until the output LED shows “d.” to enter the Save Mapping Mode.
2) Use the “+”or “-“ input push button to select the mapping configuration (0~7) which you want to save
current input/output mapping
3) After you select the desired mapping configuration number, the LED will blink twice and the mapping
setting will be saved
4) If you push the “output- (preset)”button before the mapping setting is saved, the LED will show
“一”“一”to quit the Save Mapping Mode
3. Preset Mapping Mode
1) Keep pushing “output- (preset)”button until the output LED shows “P.” to enter the Preset Mapping
Mode.
2) Use the “+”or “-“ input push button to select the saved mapping configuration (0~7) which you want to
recall
3) After you select the desired mapping configuration number, the LED will blink twice and the mapping
setting will be effective
4) If you push the “output+ (save)”button before the mapping setting is effective, the LED will show
“一”“一”to quit the Preset Mapping Mode
www.avenview.com|10
4. Default EDID Mode
1) Push “input+ (default)”button to select the input channel which you want to learn default EDID and then
keep pushing “input+ (default)”button when you select your desired input channel
2) Push the “+”or “-” output push button and then the LED will show “E”“d” one time to enter Learn
Default EDID Mode
3) Use “+”or “-” output push button to select the default EDID mode(1~8)
4) Release “input+ (default)”button after selecting the desired default EDID mode, and then the LED will
blink twice and the setting will be effective
5) It will quit the Learn Default EDID Mode if you push the “input- (learn)”button before the setting is
effective
6) The LED will show “0”“0” if the setting is success
The LED will show “F”“F” if the setting is failure
5. EDID Learning Mode
1) Push “input- (learn)”button to select the input channel which you want to learn EDID from EDID Port
and then keep pushing “input- (learn)”button when you select your desired input channel
2) Push the “+”or “-” output push button and then the LED will show “E”“L” one time to enter Learn
Output EDID Mode
3) Use “+”or “-” output push button to select EDID Port(number 4)
4) Release “input- (learn)”button after selecting the EDID Port number, and then the LED will blink twice
and the setting will be effective
5) It will quit the Learn Output EDID Mode if you push the “input+ (default)”button before the setting is
effective
6) The LED will show “0”“0” if the setting is success
The LED will show “F”“F” if the setting is failure
www.avenview.com|11
1.11 RS232 Serial Port Control
1
7
6
3
8
2
4
5
9
10
11
1
2
3
4
5
6
FW/SW Version Button
COM Port Selection
Connection Status
Connect/Disconnect Button
Power On/Off Button
EDID Button
12
7
8
9
10
11
12
Firmware Update Button
Network Button
Mapping Button
Default Reset Button
In/Out Switch Button
Mute Output Button
1. FW/SW Version Button
Click “
” button to show version information
www.avenview.com|12
2. COM Port Selection
Click “
” button to select COM Port
3. Connection Status
1) Connected Status:
2) Connecting Status:
3) Disconnected Status:
4. Connect/Disconnect Button
Click this button “
” to change connection status
www.avenview.com|13
5. Power On/Off Button
Click this button to power on/off
“
” Power on status(Blue): Click this button to power off device(Standby Mode)
“
” Power off status (Red): Click this button to power on device
6. EDID Button
www.avenview.com|14
1) Learn EDID from Default
a) Select Default EDID(1-8 Default EDID)
b) Select Input
c) Click “Learn” button to learn default EDID
2) Load EDID File to Input
a) Select Input
b) Click “Load” button to select the EDID file
3) Learn EDID From Display
a) Select EDID Port
b) Select Input
c) Click “Learn” button to learn display EDID
4) Create EDID File
a) Click “Create” button to create EDID file
www.avenview.com|15
b) Select the EDID content
c) Click “Save EDID on Computer” to save the generated EDID as a file
View EDID Content
a) Select Input, or From File
b) Click “View” button to read the EDID and analysis
www.avenview.com|16
c) Click “Save As” to save the read EDID as a file on computer
7) Firmware Update Button
1) Click “Load File” to select the firmware file which you want to update
2) Click “Break” button
3) Quickly remove and reconnect the power input connector
4) Click “Start” button to begin the firmware update
www.avenview.com|17
8) Network Button
1) Click “Read From Device” to read the device IP address
2) Select “Ethernet” and then will be a pop-up windows
3) Key in the device IP address to the pop-up windows
4) Close the pop-up windows
5) Click the connected button to connect
9) Mapping Button
1) Save Mapping:
a) Select Mapping(1-8)
b) Click “Save” button to save current mapping
www.avenview.com|18
2) Preset Mapping:
a) Select Mapping(1-8)
b) Click “Recall” button to recall previous mapping which are saved
3) Rename Mapping:
a) Rename the mapping(Mapping1-Mapping8)
b) Click “Confirm” button to confirm the change
10) Default Reset Button
Click this button to do factory default reset
The default reset process will take about 80~90 seconds
11) In/Out Switch Button
Click the button on the checkerboard to select Input & Output port
User can click the input number button to let all outputs select the same input
Ex: All outputs select input 3
www.avenview.com|19
12) Mute Output Button
Click the circle button to turn off output’s video and audio
Ex: Mute Output 2
www.avenview.com|20
1.11 EDID Learning
Software Control: Please refer to the Operation Approach\ Method C: Software Control through
RS-232 port
There are eight embedded default EDID as below,
1. Full-HD ([email protected])-24bit 2D & 2ch
2. Full-HD ([email protected])-24bit 2D & 7.1ch
3. Full-HD ([email protected])-24bit 3D & 2ch
4. Full-HD ([email protected])-24bit 3D & 7.1ch
5. HD ([email protected])([email protected])-24bit 2D & 2ch
6. HD ([email protected])([email protected])-24bit 2D & 7.1ch
7. Full-HD ([email protected])-36bit 2D & 2ch
8. Full-HD ([email protected])-36bit 2D & 7.1ch
The EDID learning function is only necessary whenever you encounter any display on the HDMI
output port that cannot play audio and video properly. Because the HDMI source devices and
displays may have various level of capability in playing audio and video, the general principle is that
the source device will output the lowest standards in audio format and video resolutions to be
commonly acceptable among all HDMI displays. In this case, a 720p stereo HDMI signal output
would be probably the safest choice. Nevertheless, the user can force the matrix to learn the EDID
of the lowest capable HDMI display among others to make sure all displays are capable to play the
HDMI signals normally.
There are THREE methods to do EDID Learning as below,
1. Front Panel Push-in Button: Please refer to the Operation Approach\ Method A: Push-in Button
2. IR Remote Control: Please refer to the Operation Approach\ Method B: IR Remote Control
www.avenview.com|21
Section 2: Specifications
Item
Units
SW-HDM3D-C6-8x8E
HDM3D-C6SW-R
8x8 HDMI Matrix Switch over CAT6
HDMI Receiver over CAT5 with 3D
with 3D Support
Support
HDMI Deep Color & Full 3D
Yes
Single Link 225 MHz (6.75Gbps)
480i / 480p / 720p / 1080i / 1080p60
Full HD: (1080p) ~ 35meter (115feet) (CAT5e) / 40meter (130feet) (CAT6)
HD: (720p/1080i) ~ 50meter (165feet) (CAT5e) / 55meter (180feet) (CAT6)
Surround Sound (up to 7.1 Ch.) or Stereo Digital Audio
8 Level Digital Control
1.2 Volts (peak-to-peak)
Unit Description
HDMI Compliance
HDCP Compliance
Video Bandwidth
Supported Resolutions
Resolution and Distance
Audio Support
Equalization
Input TMDS Signal
Input DDC Signal
ESD Protection
Input
Output
HDMI Input Selection
HDMI Source Control
IR Remote Control
HDMI Connector
RJ45 Connector
RS232 Connector
3.5mm Connector
DIP Switch
Dimensions (L x W x H)
Power Supply
Power Consumption
Description
-
5 Volts (peak-to-peak, TTL)
Human body model — ±15kV (air-gap discharge) & ±8kV (contact discharge)
Core chipset — ±8kV
8x HDMI / 1x RS-232 / 1x Ethernet
1x RJ-45 /
1x IR socket for IR receiver
1x IR socket for IR receiver
8x RJ-45 /
1x HDMI /
5x IR socket for IR blaster
1x IR socket for IR blaster
Push Button / IR Remote / RS232
Push Button / IR Remote
Through IR Control Path from IR Receiver at Remote Receiver to IR Blaster at
Matrix Switch
Electro-optical characteristics: = 25° / Carrier frequency: 20~60kHz
Type A (19 pin female)
WE/SS 8P8C with 2 LED indicators
DE-9 (9-pin D-sub Female)
Earphone jack for IR blaster
[IR Main] IR control on all source
Earphone jack for IR receiver
devices
[IR RECEIVER] Receives IR commands
[IR PASS-THROUGH 1~8] IR control on from remote control
individual source device
[SW1~SW8] 2-pin for EDID & audio mode
[SW Main] 4-pin for operation & firmware update
17” x 11” x 1.7”
3.3” x 2.4” x 1”
5V 4A DC
5V 2A DC
20 Watts [max]
1 Watt [max]
Environmental
Operating Temperature
32˚ ~ 104˚F (0˚ to 40˚C)
www.avenview.com|22
Section 3: IR Remote User Guide
ON
Power on the matrix switcher
OFF
Standby mode
MUTE
Hide or Turn off
Video/Audio
SAVE
Save current mapping mode
DEFAULT EDID
Default EDID selection
CLEAR
Clear the previous IR operation
STATUS
View Preset output Status
PRESET
Preset Mapping mode
LEARN EDID
Begin EDID learning from one output
TAKE
Trigger the previous setting
INPUT
Select the Input 1-8
OUTPUT
Select the Outputs 1-8
F1
Reserved
F2
Reserved
the selected Output’s
Ex: Select Input 2 to Output 3
Push the Green circle button as
illustrated to select Input 2 then push
the red button to output the source to
Output 3.
www.avenview.com|23
Operation
Mute Output
Procedure
7-Segment LED
Mute + (Output 1~8) + Take
Ex: Mute Output 3
Output Status
1. Press “MUTE” button
0
2. Press number key “3” to select Output 3
3
0
3.Press “TAKE” button
3
0
Status + 1~8(Output 1~8) + Take
Ex: Output 4
(Input 2)
Save Current Mapping
Ex: Save current mapping to 5
1.Press “STATUS” button
-
2.Press number key “4” to select Output 4
4
-
3.Press “TAKE” button
4
2
Save + 1~8(1-8 storage site) + Take
1.Press “SAVE” button
d
-
2.Press number key “5” to select the storage site 5
d
5
3.Press “TAKE” button
Preset Mapping
Ex: Preset saved mapping
from 5
Preset + 1~8(1-8 storage site) + Take
1.Press “PRESET” button
P
-
2.Press number key “5” to select the storage site 5
P
5
3.Press “TAKE” button
Learn default EDID
Ex: Default EDID 2
Input 3
Default EDID +1~8(1-8 default EDID) +1~8(input 1~8) +
Take
1.Press “DEFAULT EDID” button
E
d
2.Press number key “2” to select default EDID 2
2
d
3.Press number key “3” to select Input 3
2
3
4.Press “TAKE” button
0
0
(success)
F
F(fail)
www.avenview.com|24
Learn EDID Port EDID
Ex: Learn EDID Port
Input 3
Learn + D(EDID Port) +1~8(Input 1~8) + Take
1.Press “LEARN” button
E
L
2.Press number key “4” to select EDID Port
4
L
3. Press number key “3” to select Input 3
4
3
4.Press “TAKE” button
0
(success)
F
F(fail)
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the
operation or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of
Avenview concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of
anticipatory profits, or for punitive, incidental or consequential damages in connection with the furnishing, performance, or use of the
Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability,
function or design. With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties
regarding such products, including but not limited to, the implied warranties of merchantability, fitness for a particular purpose, and
non-infringement.
www.avenview.com|25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement