DJM-900SRT DJM-900SRT Serato DJ Edition DJ MIXER

DJM-900SRT DJM-900SRT Serato DJ Edition DJ MIXER
DJ MIXER
DJM-900SRT
DJM-900SRT Serato DJ Edition
http://pioneerdj.com/support/
The Pioneer DJ support site shown above offers FAQs, information on software and various other types of
information and services to allow you to use your product in greater comfort.
http://rekordbox.com/
For various types of information and services regarding rekordbox™, see the Pioneer website above.
http://serato.com/
For the latest version of the Serato DJ software, access Serato.com and download the software from there.
Operating Instructions
Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However the method of connecting and operating the unit is the same.
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
1)
2)
3)
4)
5)
6)
7)
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
D3-4-2-1-1_A1_En
11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms
or when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
D3-7-13-69_En
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_A1_En
FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Product Name: DJ MIXER
Model Number: DJM-900SRT
Responsible Party Name: PIONEER ELECTRONICS (USA) INC.
SERVICE SUPPORT DIVISION
Address: 1925 E. DOMINGUEZ ST. LONG BEACH, CA 90810-1003, U.S.A.
Phone: 1-800-421-1404
URL: http://www.pioneerelectronics.com
D8-10-4*_C1_En
2
En
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
WARNING: This product contains chemicals known
to the State of California and other governmental
entities to cause cancer and birth defects or other
reproductive harm.
D36-P5_C1_En
D3-4-2-1-3_A1_En
WARNING
This product equipped with a three-wire grounding
(earthed) plug - a plug that has a third (grounding) pin.
This plug only fits a grounding-type power outlet. If you
are unable to insert the plug into an outlet, contact a
licensed electrician to replace the outlet with a properly
grounded one. Do not defeat the safety purpose of the
grounding plug.
D3-4-2-1-6_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 5 cm at rear, and 3 cm at each side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
D3-4-2-1-7c*_A1_En
CAUTION
The POWER switch on this unit will not completely
shut off all power from the AC outlet. Since the power
cord serves as the main disconnect device for the
unit, you will need to unplug it from the AC outlet to
shut down all power. Therefore, make sure the unit
has been installed so that the power cord can be
easily unplugged from the AC outlet in case of an
accident. To avoid fire hazard, the power cord should
also be unplugged from the AC outlet when left
unused for a long period of time (for example, when
on vacation).
D3-4-2-2-2a*_A1_En
IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF
THIS EQUIPMENT ARE ON THE RIGHT SIDE.
RECORD THESE NUMBERS ON PAGE 31 FOR
FUTURE REFERENCE.
D36-AP9-3*_A1_En
Information to User
Alterations or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
D8-10-2_A1_En
CAUTION
This product satisfies FCC regulations when shielded
cables and connectors are used to connect the unit
to other equipment. To prevent electromagnetic
interference with electric appliances such as radios
and televisions, use shielded cables and connectors
for connections.
D8-10-3a_A1_En
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a
safe level – a level that lets the sound come through
clearly without annoying blaring or distortion and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time, your hearing
“comfort level” adapts to higher volumes of sound, so
what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by setting
your equipment at a safe level BEFORE your hearing
adapts.
ESTABLISH A SAFE LEVEL:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.
• Once you have established a comfortable sound
level, set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING
GUIDELINES:
• Do not turn up the volume so high that you can’t
hear what’s around you.
• Use caution or temporarily discontinue use in
potentially hazardous situations.
• Do not use headphones while operating a motorized
vehicle; the use of headphones may create a traffic
hazard and is illegal in many areas.
S001a_A1_En
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement.
S002*_A1_En
WARNING
Store small parts out of the reach of children and
infants. If accidentally swallowed, contact a doctor
immediately.
D41-6-4_A1_En
En
3
Contents
For those operating Serato DJ for the first time using this unit
See the “Quick Start Guide - Serato DJ Edition” for the procedure for making the
initial settings required to use the CONTROL CD or CONTROL VINYL in order to
operate Serato DJ. The “Quick Start Guide - Serato DJ Edition” can be downloaded
from the Pioneer DJ support site (http://pioneerdj.com/support/). For downloading
instructions, see Downloading the latest versions of the operating instructions and
the Quick Start Guide - Serato DJ Edition in this manual (p.28).
For users of CONTROL VINYL
If you use CONTROL VINYL, use a shop that handles Serato DJ products or an
online shop such as that of Serato (http://serato.com/).
How to read this manual
Be sure to read both this manual and the “Quick Start Guide – Serato DJ Edition”.
Both contain important information that you should understand before using this
product.
For instructions on obtaining the Serato DJ software’s manual, see Acquiring the
manual (p.28).
This manual consists mainly of descriptions of the functions of this unit as hardware. For details about operating the Serato DJ software, see the Serato DJ software’s manual and the “Quick Start Guide – Serato DJ Edition”.
! The Serato DJ software manual can be downloaded from “Serato.com”. For
details, see Downloading the Serato DJ software manual (p. 28).
! The latest version of the operating instructions (this manual) and the “Quick
Start Guide – Serato DJ Edition” can be downloaded from the Pioneer support
site. For details, see Downloading the latest versions of the operating instructions and the Quick Start Guide - Serato DJ Edition (p.28).
! In this manual, names of channels and buttons indicated on the product, names
of menus in the software, etc., are indicated within square brackets ([ ]). (e.g.
[MASTER] channel, [ON/OFF], [File] menu)
! Please note that the screens and specifications of the software described in this
manual as well as the external appearance and specifications of the hardware
are currently under development and may differ from the final specifications.
! Please note that depending on the operating system version, web browser settings, etc., operation may differ from the procedures described in this manual.
Before start
Features..............................................................................................................................5
What’s in the box...............................................................................................................5
Installing the software
Installing the driver software............................................................................................6
Installing the Serato DJ software.....................................................................................7
Connections
Rear panel........................................................................................................................10
Connecting input terminals............................................................................................11
Connecting output terminals.........................................................................................11
Connecting to the control panel.....................................................................................12
Connecting this unit and computer...............................................................................12
Operation
Control Panel...................................................................................................................13
Basic Operation...............................................................................................................14
Advanced Operations......................................................................................................15
Types of effects
Types of SOUND COLOR FX effects...............................................................................19
Types of BEAT EFFECT.....................................................................................................19
MIDI assignment map
MIDI assignment map.....................................................................................................22
Changing the settings
About the auto standby function....................................................................................24
About the talk over function...........................................................................................24
Setting preferences.........................................................................................................24
About the setting utility software...................................................................................24
Checking the latest information on the driver software...............................................25
Additional information
Troubleshooting...............................................................................................................26
Block Diagram.................................................................................................................27
Acquiring the manual.....................................................................................................28
About trademarks and registered trademarks.............................................................28
Specifications..................................................................................................................29
4
En
Before start
Before start
Features
This unit is a 4-channel mixer optimally designed for DJ performances using the
“Serato DJ” DJ software by Serato. It is equipped with an internal sound card that is
compatible with Serato DJ, so performances using Serato DJ can be held immediately after connecting this unit with a computer using a USB cable, with no need to
make any troublesome settings.
Furthermore, Serato DJ’s scratch function can be controlled using the CONTROL
VINYL (record) or CONTROL CD.
In addition, this unit carries over the main functions, quality and performance of the
Pioneer DJM-900nexus, a standard model in clubs throughout the world, offering
powerful support for performances by all professional DJs active in the club scene.
PLUG AND PLAY
This unit is equipped with a built-in USB sound card for connecting a computer. A
computer can be connected simply using a single USB cable; there is no need to
procure a separate sound card in addition to this unit.
Also, when Serato DJ is launched, this unit is automatically selected as the sound
device, so DJ performances using Serato DJ can be held immediately, with no need
to make any troublesome settings.
Furthermore, Serato DJ’s scratch function can be controlled using the CONTROL
VINYL (record) or CONTROL CD.
HIGH SOUND QUALITY
This unit uses a 32-bit D/A converter and other parts that are equivalent to those
of high grade audio equipment, greatly improving the sound quality of not only the
master output but also the headphones and booth output. The use of a 32-bit digital
signal processor suppresses digital noise. Furthermore, for the analog circuitry as
well, a high sound quality balanced hybrid operational amplifier and a fully balanced
output circuitry are used to reduce noise.
SOUND COLOR FX&BEAT FX
This unit is equipped with the SOUND COLOR FX and BEAT FX functions that have
been well received on the DJM series. With SOUND COLOR FX, the effects you
are aiming to create can be applied simply by turning the knob, letting you make
original arrangements of tracks and enabling a wide variety of remixing possibilities. Also, the BPM and beat position information of the track currently playing with
Serato DJ can be obtained via USB, so BEAT EFFECT can be applied on beat thanks
to the highly precise BPM information. Also, by using the quantize mode, the effect
timing is automatically corrected even if the BEAT EFFECT operation is performed
off timing, so effects can be applied in beat.
DURABLE FADER
The crossfader and channel faders use a sliding structure in which the fader knobs
are supported by two metal shafts. This provides both smooth operation with no
wobbling and high durability. It also keeps any adverse effects from liquids or dust
getting into the faders to a minimum. For scratch play compatibility, the crossfader
uses a uniquely developed magnetic system that provides a high durability of over 10
million operations with subtle operability. The channel faders provide approximately
three times greater operation durability as compared to a previous Pioneer model
(DJM-800).
STANDARD LAYOUT
This unit carries over the control panel layout of the Pioneer DJM series, the world
standard in DJ mixers.
The simple, straightforward control panel layout not only facilitates DJ performances
but lets even DJs using this unit for the first time to operate it without hesitation, so
it can be used without worry as a mixer that is permanently installed in the club.
What’s in the box
!
!
!
!
!
CD-ROM (Installation Disc)
USB cable
Power cord
Operating instructions (this document)
Serato DJ CONTROL CD × 2
En
5
Installing the software
Installing the driver software
This driver software is a proprietary program for inputting and outputting audio
signals from the computer. To use this unit connected to a computer on which
a Windows or Mac OS is installed, install the driver software on the computer
beforehand.
Software end user license agreement
This Software End User License Agreement (“Agreement”) is between you (both the
individual installing the Program and any single legal entity for which the individual
is acting) (“You” or “Your”) and PIONEER CORPORATION (“Pioneer”).
TAKING ANY STEP TO SET UP OR INSTALL THE PROGRAM MEANS THAT YOU
ACCEPT ALL OF THE TERMS OF THIS LICENSE AGREEMENT. PERMISSION TO
DOWNLOAD AND/OR USE THE PROGRAM IS EXPRESSLY CONDITIONED ON
YOUR FOLLOWING THESE TERMS. WRITTEN OR ELECTRONIC APPROVAL IS
NOT REQUIRED TO MAKE THIS AGREEMENT VALID AND ENFORCEABLE. IF
YOU DO NOT AGREE TO ALL OF THE TERMS OF THIS AGREEMENT, YOU ARE
NOT AUTHORIZED TO USE THE PROGRAM AND MUST STOP INSTALLING IT OR
UNINSTALL IT, AS APPLICABLE.
1DEFINITIONS
1 “Documentation” means written documentation, specifications and help
content made generally available by Pioneer to aid in installing and using the
Program.
2 “Program” means all or any part of Pioneer’s software licensed to You by
Pioneer under this Agreement.
2 PROGRAM LICENSE
1 Limited License. Subject to this Agreement’s restrictions, Pioneer grants to
You a limited, non-exclusive, non-transferable, license (without the right to
sublicense):
a To install a single copy of the Program in Your computer or mobile
device, to use the Program only for Your personal purpose complying
with this Agreement and the Documentation (“Authorized Use”);
b To use the Documentation in support of Your Authorized Use; and
c To make one copy of the Program solely for backup purposes, provided
that all titles and trademark, copyright and restricted rights notices are
reproduced on the copy.
2 Restrictions. You will not copy or use the Program or Documentation except
as expressly permitted by this Agreement. You will not transfer, sublicense,
rent, lease or lend the Program, or use it for third-party training, commercial
time-sharing or service bureau use. You will not Yourself or through any third
party modify, reverse engineer, disassemble or decompile the Program,
except to the extent expressly permitted by applicable law, and then only
after You have notified Pioneer in writing of Your intended activities.
3 Ownership. Pioneer or its licensor retains all right, title and interest in and to
all patent, copyright, trademark, trade secret and other intellectual property
rights in the Program and Documentation, and any derivative works thereof.
You do not acquire any other rights, express or implied, beyond the limited
license set forth in this Agreement.
4 No Support. Pioneer has no obligation to provide support, maintenance,
upgrades, modifications or new releases for the Program or Documentation
under this Agreement.
3 WARRANTY DISCLAIMER
THE PROGRAM AND DOCUMENTATION ARE PROVIDED “AS IS” WITHOUT ANY
REPRESENTATIONS OR WARRANTIES, AND YOU AGREE TO USE THEM AT
YOUR SOLE RISK. TO THE FULLEST EXTENT PERMISSIBLE BY LAW, PIONEER
EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WITH RESPECT TO THE
PROGRAM AND DOCUMENTATION, WHETHER EXPRESS, IMPLIED, STATUTORY,
OR ARISING OUT OF COURSE OF PERFORMANCE, COURSE OF DEALING OR
USAGE OF TRADE, INCLUDING ANY WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, SATISFACTORY QUALITY, ACCURACY,
TITLE OR NON-INFRINGEMENT.
4 EXPORT CONTROL AND COMPLIANCE WITH LAWS AND
REGULATIONS
You may not use or otherwise export or re-export the Program except as authorized
by United States law and the laws of the jurisdiction in which the Program was
obtained. In particular, but without limitation, the Program may not be exported
or re-exported (a) into any U.S.-embargoed countries or (b) to anyone on the U.S.
Treasury Department's Specially Designated Nationals List or the U.S. Department
of Commerce Denied Persons List or Entity List. By using the Program, you represent and warrant that you are not located in any such country or on any such list.
You also agree that you will not use the Program for any purposes prohibited by
United States law, including, without limitation, the development, design, manufacture, or production of nuclear, missile, or chemical or biological weapons.
6
En
5 U.S. GOVERNMENT RESTRICTED RIGHTS
The Program and Documentations are “commercial computer software” and “commercial computer software documentation” as those terms are defined in 48 C.F.R.
§252.227-7014 (a) (1) (2007) and 252.227-7014 (a) (5) (2007). The U.S. Government’s
rights with respect to the Program and Documentations are limited by this license
pursuant to 48 C.F.R. § 12.212 (Computer software) (1995) and 48 C.F.R. §12.211
(Technical data) (1995) and/or 48 C.F.R. §227.7202-3, as applicable. As such, the
Program and Documentations are being licensed to the U.S. Government end users:
(a) only as “commercial items” as that term is defined in 48 C.F.R. §2.101 generally
and as incorporated in DFAR 212.102; and (b) with only those limited rights as are
granted to the public pursuant to this license. Under no circumstance will the U.S.
Government or its end users be granted any greater rights than we grant to other
users, as provided for in this license. Manufacturer is Pioneer Corporation, 1-1 ShinOgura, Saiwai-ku, Kawasaki-shi, Kanagawa-Ken, 212-0031 Japan
6 DAMAGES AND REMEDIES FOR BREACH
You agree that any breach of this Agreement’s restrictions would cause Pioneer
irreparable harm for which money damages alone would be inadequate. In addition
to damages and any other remedies to which Pioneer may be entitled, You agree
that Pioneer may seek injunctive relief to prevent the actual, threatened or continued breach of this Agreement.
7TERMINATION
Pioneer may terminate this Agreement at any time upon Your breach of any provision. If this Agreement is terminated, You will stop using the Program, permanently
delete it from your computer or mobile device where it resides, and destroy all copies of the Program and Documentation in Your possession, confirming to Pioneer in
writing that You have done so. Sections 2.2, 2.3, 2.4, 3, 4, 5, 6, 7 and 8 will continue in
effect after this Agreement’s termination.
8 GENERAL TERMS
1 Limitation of Liability. In no event will Pioneer or its subsidiaries be liable
in connection with this Agreement or its subject matter, under any theory
of liability, for any indirect, incidental, special, consequential or punitive
damages, or damages for lost profits, revenue, business, savings, data, use,
or cost of substitute procurement, even if advised of the possibility of such
damages or if such damages are foreseeable. In no event will Pioneer’s
liability for all damages exceed the amounts actually paid by You to Pioneer
or its subsidiaries for the Program. The parties acknowledge that the liability
limits and risk allocation in this Agreement are reflected in the Program
price and are essential elements of the bargain between the parties, without
which Pioneer would not have provided the Program or entered into this
Agreement.
2 The limitations or exclusions of warranties and liability contained in this
Agreement do not affect or prejudice Your statutory rights as consumer and
shall apply to You only to the extent such limitations or exclusions are permitted under the laws of the jurisdiction where You are located.
3 Severability and Waiver. If any provision of this Agreement is held to be
illegal, invalid or otherwise unenforceable, that provision will be enforced to
the extent possible or, if incapable of enforcement, deemed to be severed
and deleted from this Agreement, and the remainder will continue in full
force and effect. The waiver by either party of any default or breach of this
Agreement will not waive any other or subsequent default or breach.
4 No Assignment. You may not assign, sell, transfer, delegate or otherwise
dispose of this Agreement or any rights or obligations under it, whether voluntarily or involuntarily, by operation of law or otherwise, without Pioneer’s
prior written consent. Any purported assignment, transfer or delegation by
You will be null and void. Subject to the foregoing, this Agreement will be
binding upon and will inure to the benefit of the parties and their respective
successors and assigns.
5 Entire Agreement. This Agreement constitutes the entire agreement between
the parties and supersedes all prior or contemporaneous agreements or
representations, whether written or oral, concerning its subject matter. This
Agreement may not be modified or amended without Pioneer’s prior and
express written consent, and no other act, document, usage or custom will
be deemed to amend or modify this Agreement.
6 You agree that this Agreement shall be governed and construed by and
under the laws of Japan.
Cautions on Installation
! Before installing the driver software, be sure to turn off the power of this unit and
disconnect the USB cable from both this unit and your computer.
! If you connect this unit to your computer without installing the driver software first, an error may occur on your computer depending on the system
environment.
! If you have discontinued the installation process in progress, step through
the installation process again from the beginning according to the following
procedure.
!Read Software end user license agreement carefully before installing this unit’s
proprietary driver software.
! Before installing the driver software, terminate all other programs running on
your computer.
! The driver software is compatible with the following OSs.
Supported operating systems
®
®
Windows 8/Windows 8 Pro
®
Windows 7 Home Premium/Professional/Ultimate
®
Windows Vista Home Basic/Home Premium/Business/Ultimate
®
Windows XP Home Edition/Professional (SP3 or later)
1
32-bit version
64-bit version
32-bit version
64-bit version
32-bit version
64-bit version
1
1
1
1
1
1
32-bit version
1
®
Windows XP Professional x64 Edition is not supported.
! The included CD-ROM includes installation programs in the following 12
languages.
English, French, German, Italian, Dutch, Spanish, Portuguese, Russian,
Simplified Chinese, Traditional Chinese, Korean, and Japanese
When using operating systems in other languages, follow the instructions on the
screen to select [English (English)].
Installation Procedure (Windows)
Read Cautions on Installation carefully before installing the driver software.
! To install or uninstall the driver software, you need to be authorized by the
administrator of your computer. Log on as the administrator of your computer
before proceeding with the installation.
1 Insert the included CD-ROM into the computer’s CD drive.
The CD-ROM menu is displayed.
! If the CD-ROM menu does not appear when the CD-ROM is inserted, doubleclick the CD drive from the [Start] menu – [Computer] (or [My Computer]).
2 From the menu that appears, select [Install Driver
Software], then click [Start].
3 “Download the latest version? An internet environment is
required to access the site.” is displayed. Click [Yes].
The web browser is launched and the Pioneer DJ support site is displayed.
4 Click [Software Download] under [DJM-900SRT] on the
Pioneer DJ support site.
5 Click [Driver Software].
6 From the download page, download the driver software
for Windows (DJM-900SRT_X.XXX.exe).
7 Double-click the downloaded file.
The driver installation screen appears.
8 Carefully read the Software end user license agreement
and if you consent to the provisions, put a check mark in [I
agree.] and click [OK].
If you do not consent to the provisions of the Software end user license agreement,
click [Cancel] and stop installation.
9 Proceed with installation according to the instructions on
the screen.
If [Windows Security] appears on the screen while the installation is in progress,
click [Install this driver software anyway] and continue with the installation.
! When installing on Windows XP
If [Hardware Installation] appears on the screen while the installation is in
progress, click [Continue Anyway] and continue with the installation.
! When the installation program is completed, a completion message appears.
4 “Download the latest version? An internet environment is
required to access the site.” is displayed. Click [Yes].
The web browser is launched and the Pioneer DJ support site is displayed.
5 Click [Software Download] under [DJM-900SRT] on the
Pioneer DJ support site.
6 Click [Driver Software].
7 From the download page, download the driver software
for Mac OS (DJM-900SRT_M_X.X.X.dmg).
8 Double-click the downloaded file.
The [DJM-900SRT_AudioDriver] menu screen appears.
9 Double-click [DJM-900SRT_AudioDriver.pkg].
The driver installation screen appears.
10Check the details on the screen and click [Continue
Anyway].
11When the end user license agreement appears, read
Software end user license agreement carefully, then click
[Continue Anyway].
12If you consent to the provisions of the Software end user
license agreement, click [Agree].
If you do not consent to the provisions of the Software end user license agreement,
click [I disagree] and stop installation.
13Proceed with installation according to the instructions on
the screen.
! Click [Cancel] to cancel installation after it has started.
Installing the Serato DJ software
Serato DJ is a DJ software application by Serato. DJ performances are possible by
connecting the computer on which this software is installed to this unit.
See the “Quick Start Guide - Serato DJ Edition” for the procedure for making the
initial settings required to use the CONTROL CD or CONTROL VINYL in order to
operate Serato DJ. The “Quick Start Guide - Serato DJ Edition” can be downloaded
from the Pioneer DJ support site (http://pioneerdj.com/support/). For downloading
instructions, see Downloading the latest versions of the operating instructions and
the Quick Start Guide - Serato DJ Edition in this manual (p.28).
For the latest version of the Serato DJ software, access Serato.com and download
the software from there. A software download link is also provided on the included
CD-ROM.
Please note that the software screens and specifications used for explanations in
this manual are under development and may differ from the final specifications.
For instructions on operating the Serato DJ software, see the Serato DJ software’s
manual.
! The Serato DJ software’s manual can be downloaded from “Serato.com”. For
details, see Downloading the Serato DJ software manual (p.28).
Minimum operating environment
Supported operating systems
Mac OS X: 10.6.8, 10.7.4 and 10.8
Installation procedure (Mac OS X)
Read Cautions on Installation carefully before installing the driver software.
! To install or uninstall the driver software, you need to be authorized by the
administrator of your computer. Have the name and password of the administrator of your computer ready in advance.
1 Insert the included CD-ROM into the computer’s CD drive.
The CD-ROM folder appears.
! Double-click the CD icon on the desktop when folders are not displayed after a
CD-ROM has been loaded.
2 Double-click [CD_menu.app].
Installing the software
Mac OS X 10.6 / 10.7 / 10.8
3 From the menu that appears, select [Install Driver
Software], then click [Start].
Windows: Windows 7
CPU and required memory
Intel® processor, Core™ 2 Duo 2.0 GHz or
32-bit version better
1 GB or more of RAM
Intel® processor, Core™ 2 Duo 2.4 GHz or
64-bit version better
4 GB or more of RAM
Intel® processor, Core™ 2 Duo 2.0 GHz or
32-bit version better
2 GB or more of RAM
Intel® processor, Core™ 2 Duo 2.4 GHz or
64-bit version better
4 GB or more of RAM
Others
USB port
Display resolution
Internet connection
A USB 2.0 port is required to connect the computer with this unit.
Resolution of 1 280 x 720 or greater
An Internet connection is required for registering the “Serato.
com” user account and downloading the software.
!
For the latest information on the required operating environment and compatibility as well as
to acquire the latest operating system, refer to “Software Info” under “DJM-900SRT” on the
Pioneer DJ support site below.
http://pioneerdj.com/support/
! Operation is not guaranteed on all computers, even if all the required operating environment
conditions indicated here are fulfilled.
En
7
!
!
Depending on the computer’s power-saving settings, etc., the CPU and hard disk may not
provide sufficient processing capabilities. For notebook computers in particular, make sure
the computer is in the proper conditions to provide constant high performance (for example
by keeping the AC power connected) when using Serato DJ.
Use of the Internet requires a separate contract with a provider offering Internet services and
payment of provider fees.
Installation Procedure (Windows)
Do not connect this unit and the computer until installation is completed.
! Log on as the user which was set as the computer’s administrator before
installing.
! If any other programs are running on the computer, quit them.
The message of successful installation appears once installation is completed.
11Click [Close] to quit the Serato DJ installer.
1 Insert the CD-ROM into the computer’s CD drive.
The CD-ROM menu is displayed.
! If the CD-ROM menu does not appear when the CD-ROM is inserted, open the
CD drive from [Computer (or My Computer)] in the [Start] menu, then doubleclick the [CD_menu.exe] icon.
2 When the CD-ROM’s menu appears, select [Download
Serato DJ Software.], then click [Start].
To close the CD-ROM menu, click [Exit].
3 “An internet environment is required to access the site.
Connected to the internet?” is displayed. Click [Yes].
The web browser is launched and the Pioneer DJ support site is displayed.
Installation procedure (Mac OS X)
Do not connect this unit and the computer until installation is completed.
4 Click [Software Info] under [DJM-900SRT] on the Pioneer DJ
support site.
! If any other programs are running on the computer, quit them.
[Serato DJ Support Information] is displayed.
The CD-ROM menu is displayed.
! Double-click the CD icon on the desktop when folders are not displayed after a
CD-ROM has been loaded.
5 Click the link to the Serato DJ download page.
The Serato DJ download page is displayed.
6 Log in to your “Serato.com” user account.
! If you have already registered a user account on “Serato.com”, proceed to
step 8.
! If you have not completed registering your user account, do so following the
procedure below.
— Following the instructions on the screen, input your e-mail address and
the password you want to set, then select the region in which you live.
— If you check [E-mail me Serato newsletters], newsletters providing the
latest information on Serato products will be sent from Serato.
— Once user account registration is completed, you will receive an e-mail at
the e-mail address you have input. Check the contents of the e-mail sent
from “Serato.com”.
! Be careful not to forget the e-mail address and password specified when you
performed user registration. They will be required for updating the software.
! The personal information input when registering a new user account may
be collected, processed and used based on the privacy policy on the Serato
website.
7 Click the link in the e-mail message sent from “Serato.com”.
This takes you to the Serato DJ download page. Proceed to step 9.
8 Log in.
Input the e-mail address and password you have registered to log in to “Serato.com”.
9 Download the Serato DJ software from the download
page.
Unzip the downloaded file, then double-click the unzipped file to launch the installer.
10Read the terms of the license agreement carefully, and if
you agree, select [I agree to the license terms and conditions],
then click [Install].
1 Insert the CD-ROM into the computer’s CD drive.
2 Double-click [CD_menu.app].
3 Select [Download Serato DJ Software.] from the CD-ROM’s
menu, then click [Start].
4 “An internet environment is required to access the site.
Connected to the internet?” is displayed. Click [Yes].
The web browser is launched and the Pioneer DJ support site is displayed.
5 Click [Software Info] under [DJM-900SRT] on the Pioneer DJ
support site.
[Serato DJ Support Information] is displayed.
6 Click the link to the Serato DJ download page.
The Serato DJ download page is displayed.
7 Log in to your “Serato.com” user account.
! If you have already registered a user account on “Serato.com”, proceed to
step 8.
! If you have not completed registering your user account, do so following the
procedure below.
— Following the instructions on the screen, input your e-mail address and
the password you want to set, then select the region in which you live.
— If you check [E-mail me Serato newsletters], newsletters providing the
latest information on Serato products will be sent from Serato.
— Once user account registration is completed, you will receive an e-mail at
the e-mail address you have input. Check the contents of the e-mail sent
from “Serato.com”.
! Be careful not to forget the e-mail address and password specified when you
performed user registration. They will be required for updating the software.
! The personal information input when registering a new user account may
be collected, processed and used based on the privacy policy on the Serato
website.
8 Click the link in the e-mail message sent from “Serato.com”.
This takes you to the Serato DJ download page. Proceed to step 9.
9 Log in.
Input the e-mail address and password you have registered to log in to “Serato.com”.
10Download the Serato DJ software from the download
page.
! If you do not agree to the contents of the usage agreement, click [Close] to
cancel installation.
Installation begins.
8
En
Unzip the downloaded file, then double-click the unzipped file to launch the installer.
11Read the terms of the license agreement carefully, and if
you agree, click [Agree].
Installing the software
! If you do not agree to the contents of the usage agreement, click [Disagree]
to cancel installation.
12If the following screen appears, drag and drop the [Serato
DJ] icon on the [Applications] folder icon.
En
9
Connections
Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections.
Connect the power cord after all the connections between devices have been completed.
Be sure to use the included power cord.
Refer to the operating instructions for the component to be connected.
! When creating a DVS (Digital Vinyl System) combining a computer, audio interface, etc., be careful in connecting the audio interface to this unit’s input terminals and in
the settings of the input selector switches.
Also refer to the operating instructions of the DJ software and audio interface.
Rear panel
1
2
3
45 3
CH 4
PHONO CD/ LINE
OFF
ON
R
POWER
RETURN
L (MONO)
L
4
CH 3
PHONO CD/ LINE
L
R
SEND
L (MONO)
AC IN
h
CH 2
1 GND
g
6
7
MIC2
MIDI OUT
8
CH 1
PHONO CD/ LINE
PHONO CD/ LINE
L
L
R
R
MASTER1
R
4
SIGNAL GND
L
MASTER2 REC OUT
L
L
R
R
e
d
R
BOOTH
CH2
TRS
L
R
LINK
f
Turns this unit’s power on and off.
2RETURN terminals (page 11)
Connect to the output terminal of an external effector. When the [L (MONO)]
channel only is connected, the [L (MONO)] channel input is simultaneously
input to the [R] channel.
3PHONO terminals (page 11)
Connect to a phono level (MM cartridge) output device. Do not input line level
signals.
To connect a device to the [PHONO] terminals, remove the short-circuit pin plug
inserted in the terminals.
Insert this short-circuit pin plug into the [PHONO] terminals when nothing is
connected to them to cut external noise.
4CD/LINE terminals (page 11)
Connect to a DJ player or a line level output component.
5SIGNAL GND terminal (page 11)
Connects an analog player’s ground wire here. This helps reduce noise when the
analog player is connected.
6MIC2 terminal (page 11)
Connects a microphone here.
7MIDI OUT terminal (page 11)
Connects this to the MIDI IN terminal on an external MIDI sequencer.
8Kensington security slot
9DIGITAL IN terminal (page 11)
Connect these to the digital coaxial output terminals on DJ players, etc. The
sound may be momentarily interrupted when the output signal sampling frequency is switched.
aDIGITAL MASTER OUT terminal (page 11)
Outputs the master channel audio signals.
bLINK terminal (page 11)
Connect these to the LINK terminals on Pioneer DJ players or the LAN ports of
computers on which rekordbox is installed (PRO DJ LINK).
To connect multiple devices, use a switching hub (commercially available).
Use a 100Base-TX-compatible switching hub. Some switching hubs may not
operate properly.
DIGITAL
MASTER
OUT
c
b
a
CH1
IN
CH3
CH4
2 HOT
3 COLD
1POWER button (page 14)
En
45 3
SIGNAL GND
R
10
3
9
cBOOTH terminals (page 11)
These are output terminals for a booth monitor.
dREC OUT terminals (page 11)
These are output terminals for recording.
eMASTER2 terminals (page 11)
Connect to a power amplifier, etc.
fMASTER1 terminals (page 11)
Connect to a power amplifier, etc.
Be sure to use these as balanced outputs. Be careful not to accidentally
insert the power cord of another unit.
gSEND terminals (page 11)
Connect to the input terminal of an external effector. When the [L (MONO)]
channel only is connected, a monaural audio signal is output.
hAC IN
Connects to a power outlet using the included power cord. Wait until all connections between the equipment are completed before connecting the power cord.
Be sure to use the included power cord.
WARNING
The short-circuit pin plugs out of the reach of children and infants. If accidentally
swallowed, contact a doctor immediately.
Connecting input terminals
! When creating a DVS (Digital Vinyl System) combining a computer, audio interface, etc., be careful in connecting the audio interface to this unit’s input terminals and in
the settings of the input selector switches.
Also refer to the operating instructions of the DJ software and audio interface.
Analog player
Analog player
Analog player
Analog player
Microphones
Digital audio output device
L R
L R
CH 4
CH 3
PHONO CD/ LINE
OFF
ON
POWER
PHONO CD/ LINE
L
L
RETURN
R
L (MONO)
L R
CH 2
PHONO CD/ LINE
L
L
MIC2
R
MASTER1
R
R
R
BOOTH
MASTER2 REC OUT
L
L
L
CH2
TRS
L
R
LINK
Switching hub
L R
CH1
IN
CH3
CH4
2 HOT
3 COLD
1 GND
DIGITAL
MASTER
OUT
R
R
AC IN
MIDI OUT
SIGNAL GND
R
SEND
L (MONO)
L R
CH 1
PHONO CD/ LINE
SIGNAL GND
R
Connections
L R
L R
PRO DJ LINK 1
L R
rekordbox
Computers
Pioneer DJ players 2
To power outlet
Pioneer DJ players 2
1 For details on PRO DJ LINK, see About PRO DJ LINK on page 15.
2 To use the fader start function with PRO DJ LINK, connect a LAN cable (page 16).
Connecting output terminals
CH 4
CH 3
PHONO CD/ LINE
OFF
ON
RETURN
R
L (MONO)
POWER
PHONO CD/ LINE
L
L
CH 2
MIC2
R
MASTER1
R
L
R
MASTER2 REC OUT
L
L
R
AC IN
L
1 GND
MIDI OUT
SIGNAL GND
R
R
PHONO CD/ LINE
L
SIGNAL GND
SEND
L (MONO)
CH 1
PHONO CD/ LINE
R
BOOTH
CH2
TRS
R
L
LINK
MASTER
OUT
R
2 HOT
3 COLD
CH4
DIGITAL
CH1
IN
CH3
3
L R
To power outlet
External effector 1
Power amplifier 2
L R
Power amplifier 2
Cassette deck, etc.
Power amplifier
(analog input recording device) (for booth monitor)
Digital audio
input device
MIDI sequencer
1 Also connect the external effector to the [RETURN] terminal (input terminal).
2 Be sure to use the [MASTER1] terminals only for a balanced output. Connection with an unbalanced input (such as RCA) using an XLR to RCA converter cable (or converter adapter), etc., may lower the sound quality and/or result in noise.
For connection with an unbalanced input (such as RCA), use the [MASTER2] terminals.
3 Be careful not to accidentally insert the power cord of another unit to [MASTER1] terminal.
En
11
Connecting to the control panel
Computers
Connecting this unit and computer
Be sure to connect using the
included USB cable.
For instructions on operating in combination with Serato DJ, see the “Quick Start
Guide – Serato DJ Edition”. For details, see Downloading the latest versions of the
operating instructions and the Quick Start Guide - Serato DJ Edition (p.28).
1 Connect this unit to your computer via a USB cable.
MIC
Microphones
USB
CD/ LINE PHO
DIGITAL
MIC1
1
2
3
TRIM
OVER
10
MIC 1
7
0
LEVEL
HI
4
2
MIC 2
0
1
0
MIXING
CUE
MASTER
LEVEL
A
Headphones
0
PHONES
4
1MIC1 terminal (page 15)
Connects a microphone here.
2USB terminal (page 12)
Connect the computer.
3USB connection indicator
Lights when signals are being exchanged with the computer.
4PHONES terminal (page 14)
Connect headphones here.
12
En
THRU B
This unit functions as an audio device conforming to the ASIO standards.
! This operation does not work with computers that do not support USB 2.0.
! When using ASIO-compatible applications, [USB DECK 3], [USB DECK 1], [USB
DECK 2] and [USB DECK 4] can be used as inputs.
! When using DirectX-compatible applications, only [USB DECK 3] can be used as
the input.
! The computer’s recommended operating environment depends on the DJ application. Be sure to check the recommended operating environment for the DJ
application you are using.
! When another USB audio device is connected to the computer at the same time,
it may not operate or be recognized normally.
We recommend only connecting the computer and this unit.
! When connecting the computer and this unit, we recommend connecting
directly to this unit’s USB port.
2 Press [POWER] button.
Turn on the power of this unit.
! For Windows
— The message [Installing device driver software] may appear when this
unit is first connected to the computer or when it is connected to a different
USB port on the computer. Wait a while until the message [Your devices
are ready for use] appears.
! When installing on Windows XP
—[Can Windows connect to Windows Update to search for software?]
may appear while the installation is in progress. Select [No, not this time],
then click [Next] to continue installation.
—[What do you want the wizard to do?] may appear while the installation is in progress. Select [Install the software automatically
(Recommended)], then click [Next] to continue installation.
— If [Windows Security] appears on the screen while the installation is in
progress, click [Install this driver software anyway] and continue with the
installation.
Operation
Control Panel
POWER
b
USB
CD/ LINE PHONO
DIGITAL
USB
MIC1
b
CD/ LINE PHONO
DIGITAL
USB
DECK 2
DECK 4
c
c
c
c
TRIM
10
7
0
2
LEVEL
MIC 2
0
9
12
12
7
EQ
5
0
-26 /
6
6
EQ/
EQ/
- 7 -26 /
LOW
- 7 -26 /
-24
-26 /
6
dB
f
COLOR
6
LINK
f
LOW
6
dB
f
CUE
LOW
6
6
L
dB
LOW
6
HI
CUE
CUE
L
6 6
8
FLANGER PHASER
FILTER
ROBOT
CUE
TRANS
MONO SPLIT
MELODIC
SLIP ROLL
SPIRAL
3
ROLL
ECHO
n
4
10
10
10
9
9
9
8
8
8
7
7
7
6
6
6
5
5
5
4
4
4
3
3
3
STEREO
MIXING
2
9
h
2
1
h
0
h
0
a
THRU B
A
i
THRU B
A
THRU B
i
CF.A
CF.B
1
MASTER
h
D
ISOLATOR EQ
p
LEVEL / DEPTH
CH FADER
THRU B
E
i q
MIN
CROSS FADER
MAX
ON / OFF
r
PHONES
A
C
TIME
0
CROSS FADER ASSIGN
MIC
EQ CURVE
1
0
A
i
4
0
LEVEL
A
MIDI LFO
SND/ RTN
2
o
2
1
B
REV ROLL
3
BOOTH MONITOR
MASTER
CUE
STEREO
DELAY
HEADPHONES
z
A
6
R
REVERB
FADER START
2
QUANTIZE
TAP
g m
HI
CUE
1
AUTO
/ TAP
BALANCE
MONO
7
y
R
f
COLOR
CUE
x
BEAT
-24
-26 /
g
HI
w
-10
-15
COLOR
g
HI
CUE
6
X- PAD
-7
LOW
-24
-26 /
COLOR
g
LOW
dB
ms
-5
6
-15
-24
-26 /
%
-3
ISO
- 7 -26 /
-15
v
GRID
BPM
-1
EQ/
-10
4
MST
AUTO
TAP
-2
-5
6
LOW
-10
-15
6
MID
-3
ISO
-5
6
LOW
-10
EQ/
3
B
0
-26 /
-1
-2
-3
ISO
-5
6
6
MID
-2
-3
ISO
0
-26 /
-1
MID
-2
GATE/
COMP
FILTER
0
-26 /
-1
MID
2
A
PARAMETER
4
1
SOUND COLOR FX
6
HI
4
MIC
7
2
dB
CRUSH
HI
4
9
CH SELECT
1
10
1
-24
NOISE
7
d
e
2
-10
DUB
ECHO
HI
9
10
1
-15
SPACE
7
d
e
2
- 7 -26 /
4
10
1
-5
TALK
OFF ON OVER
d
e
0
OVER
2
-3
12
9
4
-2
LOW
12
10
u
WAKE UP
BEAT EFFECTS
1
0
3
d
e
OVER
LFO FORM
UTILITY
l
TRIM
OVER
k
s
t
MIDI
START
/ STOP
ON/ OFF
LEVEL
2
-1
HI
TRIM
OVER
HI
4
CD/ LINE PHONO
DIGITAL
USB
DECK 1
TRIM
MIC 1
CD/ LINE PHONO
DIGITAL
USB
b
DECK 3
OVER
1
b
MASTER
Operation
MIC
F
B
j
1MIC1 LEVEL control (page 15)
Adjusts the sound level output from the [MIC1] channel.
2MIC2 LEVEL control (page 15)
Adjusts the sound level output from the [MIC2] channel.
3EQ (HI, LOW) controls (page 15)
These adjust the tone quality of the [MIC1] and [MIC2] channels.
4OFF, ON, TALK OVER selector switch (page 15)
Turns the microphone on/off.
5SOUND COLOR FX buttons (page 16)
These turn the SOUND COLOR FX effects on/off.
6CUE button (page 14)
Presses the [CUE] button(s) for the channel(s) you want to monitor.
7FADER START (1, 2, 3, 4) buttons (page 16)
These turn the fader start function on/off.
8MONO SPLIT, STEREO selector switch (page 14)
Switches how the monitor sound output from the headphones is distributed.
9MIXING control (page 14)
This adjusts the monitor volume balance of the sound of channels for which the
[CUE] button is pressed and the sound of the [MASTER] channel.
aLEVEL control (page 14)
Adjusts the sound level output from the headphones.
bUSB audio input indicator
Lights when sound is being input from the computer to the various channels.
cInput selector switches (page 14)
Selects the input source of each channel from the components connected to
this unit.
dTRIM control (page 14)
Adjusts the level of audio signals input in each channel.
eEQ/ISO (HI, MID, LOW) controls (page 14)
These adjust the sound quality of the respective channels.
fChannel Level Indicator (page 14)
Displays the sound level of the respective channels before passing through the
channel faders.
En
13
gCOLOR control (page 16)
This changes the parameters of the SOUND COLOR FX of the different channels.
Basic Operation
hChannel Fader (page 14)
Adjusts the level of audio signals output in each channel.
iCROSS FADER ASSIGN (A, THRU, B) selector switch (page 14)
Sets the output destination of each channel to [A] or [B].
jCrossfader (page 14)
Outputs audio signals assigned by the crossfader assign switch corresponding to the curve characteristics selected by [CROSS FADER] (Crossfader Curve
Selector Switch).
kMASTER LEVEL control (page 14)
Adjusts the audio level output from the [MASTER1] and [MASTER2] terminals.
lMaster Level Indicator (page 14)
Displays the audio level output from the [MASTER1] and [MASTER2] terminals.
mBALANCE control (page 15)
Adjusts the left/right balance of the sound output from the [MASTER1] terminals, etc.
nMONO, STEREO selector switch (page 15)
Switches the sound output from the [MASTER1] terminals, etc., between monaural and stereo.
oBOOTH MONITOR control (page 15)
Adjusts the level of audio signals output from the [BOOTH] terminal.
pEQ CURVE (ISOLATOR, EQ) selector switch (page 14)
Switches the function of the [EQ/ISO (HI, MID, LOW)] controls.
qCH FADER (
,
,
) selector switch (page 15)
Switches the channel fader’s curve characteristics.
rCROSS FADER (
,
,
) selector switch (page 15)
This switches the crossfader curve characteristics.
sON/OFF (UTILITY) button
— ON/OFF: Turns the MIDI function on/off (page 17).
— UTILITY: Displays the [USER SETUP] or [CLUB SETUP] screen (page 24).
tSTART/STOP button (page 18)
Outputting sound
1 Press [POWER] button.
Turn on the power of this unit.
2 Switch the input selector switches.
Selects the input sources for the different channels from among the devices connected to this unit.
—[DIGITAL]: Selects the DJ player connected to the [DIGITAL] terminals.
—[PHONO]: Selects the analog player connected to the [PHONO] terminals.
—[CD/LINE]: Selects the cassette deck or CD player connected to the [CD/
LINE] terminals.
—[USB]: Selects the sound of the computer connected to the [USB] port.
3 Turn the [TRIM] control.
Adjusts the level of audio signals input in each channel.
The corresponding channel level indicator lights when audio signals are being
properly input to that channel.
4 Move the channel fader away from you.
Adjusts the level of audio signals output in each channel.
5 Switch the [CROSS FADER ASSIGN (A, THRU, B)] selector
switch.
Switches the output destination of each channel.
—[A]: Assigns to [A] (left) of the crossfader.
—[B]: Assigns to [B] (right) of the crossfader.
—[THRU]: Selects this when you do not want to use the crossfader. (The signals do not pass through the crossfader.)
6 Set the crossfader.
This operation is not necessary when the [CROSS FADER ASSIGN (A, THRU, B)]
selector switch is set to [THRU].
7 Turn the [MASTER LEVEL] control.
Audio signals are output from the [MASTER1] and [MASTER2] terminals.
The master level indicator lights.
Sends the MIDI start/MIDI stop signals.
uLFO FORM (WAKE UP) button
— LFO FORM: When [MIDI LFO] is selected at BEAT EFFECT, the MIDI signal’s
waveform switches each time the button is pressed (page 20).
— WAKE UP: Cancels the auto standby mode.
vMain unit display
wX-PAD (page 17)
Adjusts the quantitative parameter of the BEAT EFFECT function.
xBEAT c, d buttons (page 16)
Set the beat fraction for synchronizing the effect sound.
yTAP (ENTER) button
— TAP: When the BPM measurement mode is set to [TAP], the BPM is input
manually by tapping the button with a finger (page 16).
— ENTER: Used to change this unit’s settings (page 24).
zQUANTIZE button
When the QUANTIZE function is turned on for BEAT EFFECT, the effect is applied
to the sound without going off tempo when the currently playing track. (page 15).
AAUTO/TAP button (page 16)
Switches the BPM measurement mode.
BBeat effect selector switch (page 16)
Switches the BEAT EFFECT effect type.
CEffect channel selector switch (page 16)
Switches the channel to which the BEAT EFFECT is to be applied.
DTIME control (page 16)
Adjusts the BEAT EFFECT’s time parameter.
ELEVEL/DEPTH control (page 16)
Adjusts the BEAT EFFECT’s quantitative parameter.
FON/OFF button (page 16)
Turns the BEAT EFFECT function on/off.
Do not pull on the channel fader and crossfader knobs with excessive force. The
knobs have a structure by which they cannot be pulled off easily. Pulling the knobs
strongly may result in damaging the unit.
14
En
Adjusting the sound quality
1 Switch the [EQ CURVE (ISOLATOR, EQ)] selector switch.
—[ISOLATOR]: Functions as an isolator.
—[EQ]: The equalizer function is set.
2 Turn the [EQ/ISO (HI, MID, LOW)] controls for the respective
channels.
The adjustable ranges for the respective controls are as shown below.
— HI: –26 dB to +6 dB (13 kHz)
— MID: –26 dB to +6 dB (1 kHz)
— LOW: –26 dB to +6 dB (70 Hz)
Monitoring sound with headphones
1 Connect headphones to the [PHONES] terminal.
2 Press the [CUE] button(s) for the channel(s) you want to
monitor.
3 Switch the [MONO SPLIT, STEREO] selector switch.
—[MONO SPLIT]: The sound of the channels for which the [CUE] button is
pressed is output from the headphones output’s left channel, the [MASTER]
channel sound is output from the right channel.
—[STEREO]: The sound of the channels for which the [CUE] button is pressed
is output from the headphones in stereo.
4 Turn the [MIXING] control.
This adjusts the monitor volume balance of the sound of channels for which the
[CUE] button is pressed and the sound of the [MASTER] channel.
5 Turn the [LEVEL] control for [HEADPHONES].
The sound of the channels for which the [CUE] button is pressed is output from the
headphones.
! When the [CUE] button is pressed again, monitoring is canceled.
Switching the fader curve
Audio is output from the [BOOTH] terminal
Select the channel fader curve characteristics
Switch the [CH FADER (
,
,
)] selector switch.
—[ ]: The curve rises suddenly at the back side.
—[ ]: A curve between the ones above and below is set.
—[ ]: The curve rises gradually (the sound gradually increases as the channel fader is moved away from the front side).
Switch the [CROSS FADER (
,
,
)] selector switch.
—[ ]: Makes a sharply increasing curve (if the crossfader is moved away
from the [A] side, audio signals are immediately output from the [B] side).
—[ ]: Makes a curve shaped between the two curves above and below.
—[ ]: Makes a gradually increasing curve (if the crossfader is moved away
from the [A] side, the sound on the [B] side gradually increases, while the
sound on the [A] gradually decreases).
Adjusts the level of audio signals output from the [BOOTH] terminal.
Advanced Operations
Using Serato DJ-supported functions
When this unit and a computer on which Serato DJ is running are connected by
USB cable, the functions below can be used.
QUANTIZE
Operation
Select the crossfader curve characteristics
Turn the [BOOTH MONITOR] control.
When tracks that have been analyzed with Serato DJ are used, tracks are put on
beat even if the [BEAT EFFECTS] [ON/OFF] button is pressed or the [X-PAD] is
touched roughly.
FADER START
Using a microphone
Playback of tracks in Serato DJ can be started by operating this unit’s fader (Fader
Start Play).
1 Connect a microphone to the [MIC1] or [MIC2] terminal.
2 Set the [OFF, ON, TALK OVER] selector switch to [ON] or
[TALK OVER].
—[ON]: The indicator lights.
—[TALK OVER]: The indicator flashes.
! When set to [TALK OVER], the sound of channels other than the [MIC] channel
is attenuated by 18 dB (default) when a sound of –10 dB or greater is input to the
microphone.
! The [TALK OVER] sound attenuation level can be changed at [USER SETUP]. For
instructions on changing this, see Changing the settings on page 24.
! The talk over mode can be switched to the normal mode or the advanced mode.
For instructions on changing it, see Changing the settings on page 24.
3 Turn the [MIC1 LEVEL] or [MIC2 LEVEL] control.
Adjust the level of the sound output from the [MIC] channel.
! Pay attention that rotating to the extreme right position outputs a very loud
sound.
4 Input audio signals to the microphone.
Adjusting the sound quality
Turn the [MIC] channels’ [EQ (HI, LOW)] controls.
The adjustable ranges for the respective controls are as shown below.
— HI: –12 dB to +12 dB (10 kHz)
— LOW: –12 dB to +12 dB (100 Hz)
Switching between monaural and stereo audio
This switches the sound output from the [MASTER1], [MASTER2], [BOOTH], [REC
OUT], [PHONES], [DIGITAL MASTER OUT] and [USB] terminals between monaural
and stereo.
! To adjust the sound output from the [USB] terminals, select [MIX (REC OUT)] at
[Mixer Audio Output] in the setting utility.
Switch the [MONO, STEREO] selector switch.
—[MONO]: Outputs monaural audio.
—[STEREO]: Outputs stereo audio.
Adjusting the L/R balance of audio
The left/right balance of the sound output from the [MASTER1], [MASTER2],
[BOOTH], [REC OUT], [PHONES], [DIGITAL MASTER OUT] and [USB] terminals can
be adjusted.
! To adjust the sound output from the [USB] terminals, select [MIX (REC OUT)] at
[Mixer Audio Output] in the setting utility.
1 Set the [MONO, STEREO] selector switch to [STEREO].
2 Turn the [BALANCE] control.
The sound’s left/right balance changes according to the direction in which the
[BALANCE] control is turned and its position.
! Rotating to the rightmost position outputs only the right sound of stereo audio.
Rotating to the leftmost position outputs only the left sound of stereo audio.
About PRO DJ LINK
When a Pioneer DJ player supporting PRO DJ LINK (e.g. CDJ-2000nexus, CDJ-2000,
CDJ-900), a computer on which rekordbox is installed and this unit are connected by
LAN cable, the PRO DJ LINK functions below can be used.
For more details on the PRO DJ LINK function, also refer to the DJ player’s handling
instructions and rekordbox’s operating instructions.
For instructions on connections, see Connecting input terminals on page 11.
! When connected using a switching hub, up to 4 DJ players and 2 computers can
be connected.
! Use a 100Base-TX-compatible switching hub. Some switching hubs may not
operate properly.
! Set the DJ player’s player number to the same number as the channel to which
the audio cable is connected.
QUANTIZE
When tracks analyzed with rekordbox are used, the track is put on beat even when
the [ON/OFF] button of [BEAT EFFECTS] is pressed or the [X-PAD] is touched
roughly.
FADER START
Playback on the DJ player can be started by operating this unit’s fader (Fader Start
Play).
LINK MONITOR
With this function, rekordbox music files stored on the computer can be quickly
monitored over the headphones.
STATUS INFORMATION
This function informs the DJ players of the connected channel status (on-air status,
channel number, etc.).
Using the QUANTIZE function
Effects can be applied to the sound in tempo with the currently playing track
based on the GRID information of tracks that have been analyzed with Serato DJ or
rekordbox.
To use the QUANTIZE function with PRO DJ LINK, connect this unit and a PRO DJ
LINK-compatible Pioneer DJ player beforehand. For instructions on connecting, see
Connecting input terminals on page 11.
In addition, music files must have been analyzed with rekordbox beforehand in order
to use the QUANTIZE function. For instructions on analyzing music files with rekordbox, also see rekordbox’s operating instructions.
! When using in combination with the CDJ-2000nexus, first update the firmware
to version 1.02 or later.
! To use in combination with the CDJ-2000 or CDJ-900, first update the firmware to
version 4.0 or later.
1 Press the [QUANTIZE] button.
The QUANTIZE function turns on.
[GRID] lights on this unit’s main unit display when the GRID information has been
properly received from Serato DJ or the DJ player and the QUANTIZE function can
be used. [GRID] flashes if the GRID information has not been properly received.
En
15
! Depending on the playing status of Serato DJ or the DJ player (off air, scratching, playing in reverse, etc.), it may not be possible to receive the GRID
information.
2 Press the [ON/OFF] button of [BEAT EFFECTS] or touch the
[X-PAD].
The effect is added to the sound in tempo with the track being played.
! When the [QUANTIZE] button is pressed again, the QUANTIZE function turns
off.
Using the FADER START function
1 Connect headphones to the [PHONES] terminal.
2 Connect a computer on which rekordbox is installed.
For instructions on connections, see Connecting input terminals on page 11.
3 Selecting the track to be monitored with rekordbox.
4 Press the [CUE] button for [LINK].
The track selected with rekordbox is output from the headphones.
! When the [CUE] button is pressed again, monitoring is canceled.
! The same operation as at Monitoring sound with headphones (steps 3 to 5) can
be performed.
When this unit and a computer on which Serato DJ is running are connected by
USB cable, such operations as starting playback of tracks in Serato DJ can be controlled using this unit’s fader.
Connect this unit and a computer on which Serato DJ is running beforehand.
In the same way, when this unit and a Pioneer DJ player are connected by LAN
cable, such operations as starting playback of the DJ player can be controlled using
this unit’s fader.
Connect the Pioneer DJ player and this unit beforehand. For instructions on connecting, see Connecting input terminals on page 11.
For instructions on setting the player numbers of Pioneer DJ players, see About PRO
DJ LINK on page 15.
The fader start function can be switched on and off for all DJ players all at once. For
the switching procedure, see Changing the settings on page 24.
! The FADER START function cannot be used when attempting to perform
DVS control while Serato DJ is set to the Absolute mode. When one of the
[FADER START (1, 2, 3, 4)] buttons is pressed while the Absolute mode is set,
that button flashes then turns off.
Canceling the SOUND COLOR FX effect
Start playback using the channel fader
Press the [SOUND COLOR FX] selection button that is flashing.
1 Set the [CROSS FADER ASSIGN (A, THRU, B)] selector switch
to [THRU].
2 Press one of the [FADER START (1, 2, 3, 4)] buttons.
Select the channel to be started with the fader start function.
! For Serato DJ
—[Fader Start 1] button: Selects [DECK 3].
—[Fader Start 2] button: Selects [DECK 1].
—[Fader Start 3] button: Selects [DECK 2].
—[Fader Start 4] button: Selects [DECK 4].
Using the SOUND COLOR FX function
These are effects that change in association with the [COLOR] control.
1 Press one of the [SOUND COLOR FX] selection buttons.
This selects the type of effect.
The button that was pressed flashes.
! Even if one of the [SOUND COLOR FX] selection buttons is already selected,
when a different button is selected and pressed, that button is selected.
! For the types of effects, see Types of SOUND COLOR FX effects on page 19.
! The same effect is set for [CH1] to [CH4].
2 Turn the [COLOR] control.
The effect is applied to the channel(s) for which the control(s) was (were) pressed.
The effect is canceled.
Using the BEAT EFFECT function
This function lets you instantaneously set various effects according to the tempo
(BPM = Beats Per Minute) of the currently playing track.
Main unit display
1
CH SELECT
3 Set the channel fader to the nearest position towards you.
2
4 Set a cue in Serato DJ or on the DJ player.
1
2
3
4
MIC
A
B
MST
The track cues to the cue point and the pause mode is set.
PARAMETER
5 Move the channel fader away from you.
3
Playback of the track in Serato DJ or the DJ player starts.
! If you set the channel fader back to the original position, the player instantaneously returns to the cue point already set and pauses playback (back cue).
7
1
1 Set the [CROSS FADER ASSIGN (A, THRU, B)] selector switch
to [A] or [B].
2
2 Press one of the [FADER START (1, 2, 3, 4)] buttons.
3
4
3 Set the crossfader.
Set to the edge opposite the side on which the channel you want to use with the
fader start function is set.
5
4 Set a cue in Serato DJ or on the DJ player.
6
The track cues to the cue point and the pause mode is set.
5 Set the crossfader.
Playback of the track in Serato DJ or the DJ player starts.
! If you set the crossfader back to the original position, the player instantaneously
returns to the cue point already set and pauses playback (back cue).
7
8
9
Using the LINK MONITOR function
! Check [Use “LINK MONITOR” of Pioneer DJ Mixers.] at [File] > [Preferences]
> [Audio] in rekordbox beforehand. Also refer to the rekordbox operating
instructions.
16
En
GRID
BPM
4
5
6
%
8
ms
9
a
Start playback using the crossfader
Select the channel to be started with the fader start function.
! For Serato DJ
—[Fader Start 1] button: Selects [DECK 3].
—[Fader Start 2] button: Selects [DECK 1].
—[Fader Start 3] button: Selects [DECK 2].
—[Fader Start 4] button: Selects [DECK 4].
AUTO
TAP
a
Effect display
section
Channel select
display section
The name of the selected effect is displayed.
The name of the channel to which the effect is applied is displayed.
[AUTO] lights when the BPM measurement mode is set to the auto
mode.
[TAP] lights when in the manual input mode.
When in the auto mode, this displays the automatically detected
BPM value.
BPM value display When the BPM cannot be detected, the previously detected BPM
(3 digits)
value is displayed and flashes.
When in the manual input mode, this displays the BPM value that
was input manually.
This lights when Serato DJ is running and the QUANTIZE function can be used. It also lights when playing a track that has been
GRID
analyzed with rekordbox and the QUANTIZE function can be used
in combination with the DJ player. It flashes or is off when the
QUANTIZE function cannot be used.
BPM
This is always lit.
This displays the parameters specified for the individual effects.
When the [BEAT c, d] button is pressed, the corresponding beat
Parameter display fraction is displayed for 1 second.
section
When a value outside the parameter range is specified with the
[BEAT c, d] button, the value does not change and the display
flashes.
% (ms)
These light according to the units for the different effects.
Beat display
This lights according to the selected beat number position.
section
Touch display
This lights when the [X-PAD] is touched.
section
AUTO (TAP)
1 Press [AUTO/TAP] button.
Select the BPM measurement mode.
—[AUTO]: The BPM is measured automatically from the audio signal that is
being input. The [AUTO] mode is set when this unit’s power is turned on.
—[TAP]: The BPM is input manually by tapping the [TAP] button with a finger.
! The [AUTO] BPM measurement range is BPM = 70 to 180. With some tracks it
may not be possible to measure the BPM correctly. If the BPM cannot be measured, the BPM value on the display flashes. In such cases, use the [TAP] button
to input the BPM manually.
2 Turn the beat effect selector switch.
This selects the type of effect.
! For the types of effects, see Types of BEAT EFFECT on page 19.
! To use [SND/RTN], see Using the external effector below.
! To use [MIDI LFO], see Using the MIDI LFO on page 17.
Operating procedure 2
1 Perform steps 1 to 5 of the Using the BEAT EFFECT function
procedure.
2 Touch the [X-PAD].
The [X-PAD] changes the effect’s quantitative parameter.
Operating DJ software using the MIDI function
This selects the channel to which the effect is applied.
—[1] – [4]: The effect is applied to the sound of the respective channel.
—[MIC]: The effect is applied to the sound of [MIC] channel.
—[CF.A], [CF.B]: The effect is applied to the sound of the crossfader’s [A] (left)
or [B] (right) side.
—[MASTER]: The effect is applied to the sound of the [MASTER] channel.
! This operation is not necessary when [MIDI LFO] is selected.
4 Press the [BEAT c, d] button.
1 Connect this unit’s [USB] terminal to the computer.
For details about connections, see Connecting to the control panel on page 12.
Set the beat fraction for synchronizing the effect sound.
The effect time corresponding to the beat fraction is set automatically.
2 Launch the DJ software.
5 Press the [ON/OFF] button for [BEAT EFFECTS].
Turn the MIDI function on.
Transmission of the MIDI messages begin.
! When a fader or control is moved, a message corresponding to the position is
sent.
! When the [START/STOP] button is pressed and held in for more than 2 seconds,
a set of MIDI messages corresponding to the button, fader or control positions is
sent (Snapshot).
! When the [ON/OFF (UTILITY)] button is pressed again, sending of the MIDI messages is stopped.
! The MIDI timing clock (BPM information) is sent regardless of the status of the
[ON/OFF (UTILITY)] button.
The effect is applied to the sound.
The effect’s time parameter can be adjusted by turning the [TIME] control.
The effect’s quantitative parameter can be adjusted by turning the [LEVEL/DEPTH]
control.
The [ON/OFF] button flashes when the effect is on.
! When the [ON/OFF] button is pressed again, the effect turns off.
Inputting the BPM manually
Tap the [TAP] button at least 2 times in rhythm with the beat
(in quarter notes) of the sound being played.
The average value of the interval at which the [TAP] button was tapped by finger is
set as the BPM.
! When the BPM is set using the [TAP] button, the beat fraction is set to [1/1] and
the time of one beat (quarter note) is set as the effect time.
! The BPM can be set manually by turning the [TIME] control while pressing the
[TAP] button.
! The BPM can be set in units of 0.1 by pressing the [AUTO/TAP] button while
pressing the [TAP] button and turning the [TIME] control while pressing the two
buttons.
Making the preparations to use the MIDI LFO function
The MIDI-compatible software, devices, etc. (referred to as the “MIDI signal reception side” below) must be prepared (“learned”) before using the MIDI LFO function.
Perform the learning operations on the MIDI signal reception side.
! For the messages output by this unit, see MIDI assignment map on page 22.
1 Press the [ON/OFF (UTILITY)] button.
Turn the MIDI function on.
2 Turn the beat effect selector switch.
3 Press the [ON/OFF] button for [BEAT EFFECTS].
1 Connect this unit and external effector.
For instructions on connections, see Connecting output terminals on page 11.
2 Turn the beat effect selector switch.
Select [SND/RTN (MIDI LFO)].
3 Turn the effect channel selector switch.
This selects the channel to which the effect is applied.
4 Press the [ON/OFF] button for [BEAT EFFECTS].
The sound that has passed through the external effector is output from the
[MASTER] channel.
! When the [ON/OFF] button is pressed again, the effect turns off.
Operating the [X-PAD]
Operating [ON/OFF] button status of [BEAT
X-PAD
procedure EFFECTS]
Off (lit)
On (flashing)
3 Press the [ON/OFF (UTILITY)] button.
Select [SND/RTN (MIDI LFO)].
[S/RhLFO] flashes on the effect display section, then [SND/RTN] is displayed.
Using the external effector
1
2
Operation
3 Turn the effect channel selector switch.
This unit outputs the operation information of buttons and controls in universal MIDI
format.
When connected by USB cable to a computer on which a MIDI-compatible DJ software program is installed, the DJ software can be operated from this unit.
Install the DJ software on your computer in advance. Also, adjust the audio and
MIDI settings for the DJ software.
! For MIDI channel setting instructions, see Changing the settings on page 24.
! For the messages output by this unit, see MIDI assignment map on page 22.
Release n Touch
Release n Touch
Effect
Off n On
On n On
Learn the [ON/OFF] button’s MIDI message of the [BEAT EFFECTS] in the MIDI
signal reception side.
! The MIDI message sent from the [ON/OFF] button of the [BEAT EFFECTS] differs when [SND/RTN (MIDI LFO)] is selected and when anything other than
[SND/RTN (MIDI LFO)] is selected.
The [ON/OFF] button’s MIDI message of [BEAT EFFECTS] when [SND/RTN
(MIDI LFO)] is selected is only sent when the operation is performed following
this procedure.
4 Press the [LFO FORM (WAKE UP)] button.
Learn the [LFO FORM (WAKE UP)] button’s MIDI message in the MIDI signal reception side.
[1/7
] and [1/7 LFO] are displayed alternately on the effect display section.
! If necessary, set the MIDI mapping for other buttons and controls.
Because the [LFO FORM (WAKE UP)] button’s MIDI message is sent sequentially, depending on the MIDI signal reception side’s settings, it may not be
possible to learn the MIDI message.
To set the MIDI mapping for other buttons and controls, press the
[LFO FORM(WAKE UP)] button to switch to [SND/RTN].
Using the MIDI LFO
Operating procedure 1
Make the preparations following the procedure at Making the preparations to use the
MIDI LFO function beforehand.
1 Perform steps 1 to 4 of the Using the BEAT EFFECT function
procedure.
1 Turn the beat effect selector switch.
2 Touch the [X-PAD].
The [X-PAD] turns the effect on and off and changes the quantitative parameter.
! When you release your finger from the [X-PAD], the effect turns off.
! To keep the effect on when you release your finger from the [X-PAD], while
touching the [X-PAD] press the [ON/OFF] button of [BEAT EFFECTS], then
release your finger from the [X-PAD].
Select [SND/RTN (MIDI LFO)].
[S/RhLFO] flashes on the effect display section, then [SND/RTN] is displayed.
2 Press the [LFO FORM (WAKE UP)] button.
Transmission of the MIDI signals begins.
The MIDI signal waveform pattern switches each time the [LFO FORM (WAKE UP)]
button is pressed.
En
17
[SND/RTN]
[7/7
]
[1/7
]
[6/7
]
[2/7
[5/7
]
]
[3/7
[4/7
]
]
3 Press the [BEAT c, d] button.
Set the MIDI signal’s waveform output time.
4 Press the [ON/OFF] button of [BEAT EFFECTS] or touch the
[X-PAD].
The MIDI message for turning the effect on is sent.
! When the [LFO FORM (WAKE UP)] button is pressed and a setting from
[1/7
] – [7/7
] is selected, the MIDI message for the buttons and controls below can be sent even when the MIDI mode is turned off.
—[X-PAD] (Touch n Release)
—[CUE] button of [BEAT EFFECTS]
— Effect channel selector switch
—[LEVEL/DEPTH] control
—[ON/OFF] button of [BEAT EFFECTS]
! When the [LFO FORM (WAKE UP)] button is pressed to switch between
[SND/RTN] and [MIDI LFO], BEAT EFFECT automatically turns off.
! It is not possible to switch between [SND/RTN] and [MIDI LFO] while touching
the [X-PAD].
Sending the MIDI start and MIDI stop messages
Press the [START/STOP] button for [MIDI].
! The MIDI start and MIDI stop messages are sent alternatively each time the
[START/STOP] button is pressed, regardless of whether the MIDI function is on
or off.
Operating an external MIDI sequencer
This unit outputs the operation information of buttons and controls in universal MIDI
format.
This unit sends the tempo of the currently playing source (BPM information) as the
MIDI timing clock. This can be used to synchronize an external MIDI sequencer with
the tempo of the source.
! For the messages output by this unit, see MIDI assignment map on page 22.
! External MIDI sequencers not supporting MIDI timing clocks cannot be
synchronized.
! External MIDI sequencers cannot be synchronized for sources for which the
BPM cannot be measured stably.
! The MIDI timing clock is output even with BPM values input manually by tapping
the [TAP] button with a finger. The MIDI timing clock output range is 40 BPM to
250 BPM.
1 Connect the [MIDI OUT] terminal to the external MIDI
sequencer’s MIDI IN terminal using a commercially available
MIDI cable.
2 Set the external MIDI sequencer’s sync mode to Slave.
3 Press the [START/STOP] button for [MIDI].
The MIDI start message is sent.
4 Press [ON/OFF] in the [MIDI] section.
Transmission of the MIDI messages begin.
18
En
Types of effects
Types of SOUND COLOR FX effects
Effect Name
Descriptions
[COLOR] control
SPACE
DUB ECHO
GATE/COMP
NOISE
CRUSH
FILTER
SPIRAL1 2
This function adds a reverberation effect to the input sound.
When the delay time is changed, the pitch changes simultaneously.
Input sound turned off
Fade-out
Time
1 beat
BEAT c, d buttons (parameter 1)
TIME control (parameter 2)
LEVEL/DEPTH control (parameter 3)
X-PAD (parameter 4)
This function adds a reverberation effect to the input sound.
Direct sound
Level
Early reflected sound
Reverberations
1%
Time
100%
TIME control (parameter 2)
LEVEL/DEPTH control (parameter 3)
X-PAD (parameter 4)
DELAY1
A delay sound is output once according to the beat fraction set with the [BEAT c,
d] buttons.
When 1/2 beat delay sound is added, 4 beats become 8 beats.
Use these to set a time delay of 1/8 – 16/1 with respect to the
time of one beat of the BPM.
Use this to set the delay time.
10 to 4000 (ms)
Use this to set the balance between the original sound and the
effect sound and to set the quantitative parameter.
Use this to set the delay time.
REVERB1 2
BEAT c, d buttons (parameter 1)
Types of BEAT EFFECT
Use this to set the balance between the original sound and the
echo sound.
Use this to set the delay time.
Types of effects
Turn counterclockwise: Applies the
reverberation effect to the mid- and
Applies a reverberation effect to
low ranges.
the original sound.
Turn clockwise: Applies the reverberation effect to the mid- and high
ranges.
Applies an echo effect, with the
Turn counterclockwise: Applies the
sound delayed slightly after the
echo effect to the mid-range only.
original sound output several
Turn clockwise: Applies the echo
times and gradually attenuated.
effect to the high range only.
Turn counterclockwise: A gate
effect makes the sound tighter,
Changes the texture of the overall with a reduced sense of volume.
sound.
Turn clockwise: A compressor
effect makes the sound fatter, with
an increased sense of volume.
White noise generated inside
this unit is mixed in to the sound
Turn counterclockwise: The cutof the channel via the filter and
off frequency of the filter through
output.
which the white noise passes
! The volume can be adjusted
gradually decreases.
by turning the [TRIM]
Turn clockwise: The cut-off frecontrols for the respective
quency of the filter through which
channels. The sound quality
the white noise passes gradually
can be adjusted by turning
increases.
the [EQ/ISO (HI, MID, LOW)]
controls.
Turn counterclockwise: Increases
the sound’s distortion.
Changes the original sound to a
Turn clockwise: The sound is
crushed-like sound for output.
crushed before passing through
the high pass filter.
Turn counterclockwise: Gradually
decreases the low-pass filter’s
cutoff frequency.
Outputs sound that has passed
Turn clockwise: Gradually
through a filter.
increases the high-pass filter’s
cutoff frequency.
LEVEL/DEPTH control (parameter 3)
X-PAD (parameter 4)
Use these to set the extent of the reverberation effect, from
1 – 100 %.
Use this to set the degree of the reverb effect.
1 – 100 (%)
Sets the balance between the original sound and the effect
sound.
Sets the filter’s cut-off frequency.
TRANS1
The sound is cut according to the beat fraction set with the [BEAT c, d] buttons.
Original
(4 beats)
Cut
1/2 delay
(8 beats)
1/1 beat
BEAT c, d buttons (parameter 1)
TIME control (parameter 2)
LEVEL/DEPTH control (parameter 3)
X-PAD (parameter 4)
Use these to set a time delay of 1/8 – 16/1 with respect to the
time of one beat of the BPM.
Use this to set the delay time.
1 to 4000 (ms)
Use this to set the balance between the original sound and the
delay sound.
Use this to set the delay time.
Cut
Time
Use these to set a cut time of 1/16 – 16/1 with respect to the
BEAT c, d buttons (parameter 1)
time of one beat of the BPM.
Use this to set the effect time.
TIME control (parameter 2)
10 to 16000 (ms)
LEVEL/DEPTH control (paramSets the balance between the original sound and the effect
eter 3)
sound.
X-PAD (parameter 4)
This sets the cut time.
ECHO1 2
FILTER1
A delay sound is output several times and gradually attenuated according to the
beat fraction set with the [BEAT c, d] buttons.
With 1/1 beat echoes, the delay sounds are faded out according to the track’s tempo
even after the input sound has been cut.
The filter’s cutoff frequency changes according to the beat fraction set with the
[BEAT c, d] buttons.
Input sound turned off
Fade-out
1 beat
BEAT c, d buttons (parameter 1)
TIME control (parameter 2)
Time
Use these to set a time delay of 1/8 – 16/1 with respect to the
time of one beat of the BPM.
Use this to set the delay time.
1 to 4000 (ms)
Frequency
Use these to set the cycle for moving the cut-off frequency
BEAT c, d buttons (parameter 1) as a time of 1/4 – 64/1 with respect to the time of one beat of
the BPM.
Use this to set the cycle at which the cut-off frequency is
TIME control (parameter 2)
moved.
10 to 32000 (ms)
LEVEL/DEPTH control (paramThe further the control is turned clockwise, the more the effect
eter 3)
is stressed.
En
19
The cycle at which the cut-off frequency is moved fluctuates
finely.
X-PAD (parameter 4)
BEAT c, d buttons (parameter 1)
TIME control (parameter 2)
LEVEL/DEPTH control (parameter 3)
X-PAD (parameter 4)
FLANGER1
Use these to set an effect time of 1/16 – 16/1 with respect to
the time of one beat of the BPM.
Use this to set the effect time.
10 to 4000 (ms)
Use this to set the balance between the original sound and
ROLL.
Use this to set the effect time.
A 1-cycle flanger effect is produced according to the beat fraction set with the [BEAT
c, d] buttons.
Short delay
ROLL1 2
Time
Cycle
BEAT c, d buttons (parameter 1)
TIME control (parameter 2)
LEVEL/DEPTH control (parameter 3)
X-PAD (parameter 4)
Use these to set the 1/4 – 64/1 effect time with respect to the
time of one beat of the BPM.
Use this to set the cycle by which the flanger effect moves.
10 to 32000 (ms)
The further the control is turned clockwise, the more the effect
is stressed.
When turned all the way counterclockwise, only the original
sound is output.
The cycle at which the flanger effect is moved fluctuates finely.
The sound being input at the point when the [ON/OFF] is pressed is recorded, and
the recorded sound is output repeatedly according to the beat fraction set with the
[BEAT c, d] buttons.
Original
Effect turned on
1/1 roll
Repeated
BEAT c, d buttons (parameter 1)
PHASER1
TIME control (parameter 2)
The phaser effect changes according to the beat fraction set with the [BEAT c, d]
buttons.
LEVEL/DEPTH control (parameter 3)
X-PAD (parameter 4)
Use these to set an effect time of 1/16 – 16/1 with respect to
the time of one beat of the BPM.
Use this to set the effect time.
10 to 4000 (ms)
Use this to set the balance between the original sound and
ROLL.
Use this to set the effect time.
Phase shift
Time
Cycle
Use these to set the cycle for moving the phaser effect as of
BEAT c, d buttons (parameter 1) time of 1/4 – 64/1 with respect to the time of one beat of the
BPM.
This sets the cycle by which the phaser effect is moved.
TIME control (parameter 2)
10 to 32000 (ms)
The further the control is turned clockwise, the more the effect
LEVEL/DEPTH control (paramis stressed.
eter 3)
When turned all the way counterclockwise, only the original
sound is output.
X-PAD (parameter 4)
The cycle at which the phaser effect is moved fluctuates finely.
REV ROLL1 2
The sound being input at the point when the [ON/OFF] button is pressed is
recorded, and the recorded sound is reversed then output repeatedly according to
the beat fraction set with the [BEAT c, d] buttons.
Original
Effect turned on
1/1 reverse
roll
Reversed and repeated
Use these to set an effect time of 1/16 – 16/1 with respect to
the time of one beat of the BPM.
Use this to set the effect time.
10 to 4000 (ms)
Use this to set the balance between the original sound and
ROLL.
Use this to set the effect time.
ROBOT1
BEAT c, d buttons (parameter 1)
The original sound is changed to a sound like one produced by a robot.
TIME control (parameter 2)
Use this to set the degree of the effect sound.
BEAT c, d buttons (parameter 1)
-100–100 (%)
Use this to set the degree of the effect sound.
TIME control (parameter 2)
-100–100 (%)
LEVEL/DEPTH control (paramSets the balance between the original sound and the effect
eter 3)
sound.
X-PAD (parameter 4)
This changes the degree of the effect sound.
LEVEL/DEPTH control (parameter 3)
X-PAD (parameter 4)
SND/RTN (MIDI LFO)
MELODIC1 2
Connect an external effector, etc., here.
By pressing the [LFO FORM (WAKE UP)] button, MIDI-compatible software and
devices can be controlled using MIDI signals.
The mid-range of the sound being input at the point when the [ON/OFF] button is
pressed is recorded, and the recorded sound is output according to the level of the
sound being input.
BEAT c, d buttons (parameter 1)
TIME control (parameter 2)
LEVEL/DEPTH control (parameter 3)
X-PAD (parameter 4)
This sets the way in which the recorded sound is played.
This sets the way in which the recorded sound is played.
This sets the balance between the original sound and the
recorded sound.
This sets the way in which the recorded sound is played.
SND/RTN1
Connect an external effector, etc., here.
SEND
RETURN
0
9
9
9
9
0
0
SLIP ROLL1 2
12
12
12
-26 /
6
-26 /
6
-26 /
6
-26 /
6
-26 /
6
-26 /
6
-26 /
6
-26 /
6
-26 /
6
-26 /
6
-26 /
6
-26 /
6
Effector
TALK
OFF ON OVER
The sound being input at the point when the [ON/OFF] is pressed is recorded, and
the recorded sound is output repeatedly according to the beat fraction set with the
[BEAT c, d] buttons.
When the effect time changes, the input sound is recorded again.
Original
Effect turned on
12
BEAT c, d buttons (parameter 1)
TIME control (parameter 2)
LEVEL/DEPTH control (parameter 3)
X-PAD (parameter 4)
Changed from 1/2
to 1/1
Roll
1/2 repeat
DJM-900SRT Serato DJ Edition
1/1 repeat
—
—
This adjusts the sound level input to the [RETURN] terminal.
—
MIDI LFO
The MIDI signal (0 – 127) waveform is changed according to the track’s tempo.
20
En
The MIDI signal waveform pattern switches each time the [LFO FORM (WAKE UP)]
button is pressed.
BEAT c, d buttons (parameter 1)
TIME control (parameter 2)
LEVEL/DEPTH control (parameter 3)
X-PAD (parameter 4)
!
Use these to set a waveform output time of 1/4 – 64/1 with
respect to one beat of the BPM.
Use this to set the waveform output time.
—
This changes the MIDI signal’s waveform pattern.
When [MIDI LFO] is selected, the sound of the external effector connected to the [RETURN]
terminal is not input.
Types of effects
1 When [CF.A], [CF.B] or [MASTER] is selected with the effect channel selector
switch, if the sound of the channel you want to monitor is not being output to
the [MASTER] channel, the effect sound cannot be monitored even if the [CUE]
button for [BEAT EFFECTS] is pressed.
2 If the effect is off, the effect sound cannot be monitored even by pressing the
[CUE] button for [BEAT EFFECTS].
En
21
MIDI assignment map
MIDI assignment map
! “CC” is the abbreviation of “control change”. A control change is a type of MIDI signal used to transmit various types of control information, such as timbre, volume, etc.
On this unit, values from 0 to 127 are output as CC mainly when controls and faders are operated. CC are also output when certain buttons are operated.
! “Note” is a MIDI term used when pressing or releasing notes on a piano or other keyboard.
Button/Control/Switch
Name
Category
DIGITAL
CD/LINE
PHONO
USB DECK 3
Input Selector Switch
CH1
TRIM
HI
MID
LOW
COLOR
CUE
Channel fader
CROSS FADER ASSIGN
DIGITAL
CD/LINE
PHONO
USB DECK 1
Input Selector Switch
CH2
TRIM
HI
MID
LOW
COLOR
CUE
Channel fader
CROSS FADER ASSIGN
DIGITAL
CD/LINE
PHONO
USB DECK 2
Input Selector Switch
CH3
TRIM
HI
MID
LOW
COLOR
CUE
Channel fader
CROSS FADER ASSIGN
DIGITAL
CD/LINE
PHONO
USB DECK 4
Input Selector Switch
CH4
Crossfader
Fader curve
Master
BOOTH MONITOR
LINK
BEAT EFFECTS
22
En
TRIM
HI
MID
LOW
COLOR
CUE
Channel fader
CROSS FADER ASSIGN
Crossfader
CH FADER (
,
,
)
CROSS FADER (
,
,
)
MASTER LEVEL
BALANCE
CUE
EQ CURVE (ISOLATOR, EQ)
BOOTH MONITOR
CUE
c
d
AUTO/TAP
TAP
CUE
DELAY
ECHO
SPIRAL
REVERB
TRANS
FILTER
FLANGER
EFFECT SELECT
PHASER
ROBOT
MELODIC
SLIP ROLL
ROLL
REV ROLL
SND/RTN (MIDI LFO)
Type
MIDI assignment
Trigger/Toggle
Transmitted data
Switch
Switch
Switch
Switch
Control
Control
Control
Control
Control
Button
Control
Switch
Switch
Switch
Switch
Switch
Control
Control
Control
Control
Control
Button
Control
Switch
Switch
Switch
Switch
Switch
Control
Control
Control
Control
Control
Button
Control
Switch
Switch
Switch
Switch
Switch
Control
Control
Control
Control
Control
Button
Control
Switch
Control
Switch
Note 050
Note 051
Note 052
Note 053
CC 001
CC 002
CC 003
CC 004
CC 005
CC 070
CC 017
CC 065
Note 054
Note 055
Note 056
Note 057
CC 006
CC 007
CC 008
CC 009
CC 010
CC 071
CC 018
CC 066
Note 058
Note 059
Note 060
Note 061
CC 012
CC 014
CC 015
CC 021
CC 022
CC 072
CC 019
CC 067
Note 062
Note 063
Note 064
Note 065
CC 080
CC 081
CC 092
CC 082
CC 083
CC 073
CC 020
CC 068
CC 011
CC 094
2
2
2
2
—
—
—
—
—
Trigger/Toggle
—
—
2
2
2
2
—
—
—
—
—
Trigger/Toggle
—
—
2
2
2
2
—
—
—
—
—
Trigger/Toggle
—
—
2
2
2
2
—
—
—
—
—
Trigger/Toggle
—
—
—
—
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
0-127
0-127
0-127
0-127
0-127
OFF=0, ON=127
0-127
0, 64, 127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
0-127
0-127
0-127
0-127
0-127
OFF=0, ON=127
0-127
0, 64, 127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
0-127
0-127
0-127
0-127
0-127
OFF=0, ON=127
0-127
0, 64, 127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
0-127
0-127
0-127
0-127
0-127
OFF=0, ON=127
0-127
0, 64, 127
0-127
0, 64, 127
Switch
CC 095
—
0, 64, 127
Control
Control
Button
Switch
Control
Button
Button
Button
Button
Button
Button
Switch
Switch
Switch
Switch
Switch
Switch
Switch
Switch
Switch
Switch
Switch
Switch
Switch
Switch
CC 024
CC 023
CC 074
CC 033
CC 025
CC 115
CC 076
CC 077
CC 069
CC 078
CC 075
CC 042
CC 055
CC 043
CC 054
CC 053
CC 059
CC 050
CC 057
CC 051
CC 061
CC 058
CC 046
CC 047
CC 062
—
—
Trigger/Toggle
—
—
Trigger/Toggle
Trigger/Toggle
Trigger/Toggle
Trigger/Toggle
Trigger only
Trigger/Toggle
2
2
2
2
2
2
2
2
2
2
2
2
2
2
0-127
0-127
OFF=0, ON=127
0, 127
0-127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
Button/Control/Switch
Name
Category
CC 045
—
LEVEL/DEPTH
X-PAD
ON/OFF
X-PAD (touch)
! When an effect other than [SND/RTN (MIDI
LFO)] is selected at BEAT EFFECT
ON/OFF
X-PAD (touch)
! When [SND/RTN (MIDI LFO)] is selected at
BEAT EFFECT
HI
LOW
NOISE
Control
Control
CC 091
CC 116
—
—
Button
CC 114
2
OFF=0, ON=127
Button
CC 064
2
OFF=0, ON=127
Control
Control
Button
CC 030
CC 031
CC 085
—
—
Trigger/Toggle
0-127
0-127
OFF=0, ON=127
SPACE
Button
CC 105
Trigger/Toggle1
OFF=0, ON=127
GATE/COMP
Button
CC 106
Trigger/Toggle1
OFF=0, ON=127
DUB ECHO
Button
CC 107
Trigger/Toggle1
OFF=0, ON=127
CRUSH
Button
CC 086
Trigger/Toggle1
OFF=0, ON=127
FILTER
Fader Start 1
Fader Start 2
Fader Start 3
Fader Start 4
MIXING
LEVEL
Button
Button
Button
Button
Button
Control
Control
CC 087
CC 088
CC 089
CC 090
CC 093
CC 027
CC 026
Trigger/Toggle1
Trigger/Toggle
Trigger/Toggle
Trigger/Toggle
Trigger/Toggle
—
—
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
0-127
0-127
HEADPHONES
Timing Clock
—
Fader Start operation
3
Timing Clock
—
—
Channel fader 1 or crossfader
Note 102
—
BACK CUE = 0, PLAY = 127
Channel fader 2 or crossfader
Note 103
—
BACK CUE = 0, PLAY = 127
Channel fader 3 or crossfader
Note 104
—
BACK CUE = 0, PLAY = 127
Note 105
—
BACK CUE = 0, PLAY = 127
START
STOP
—
—
—
—
Channel fader 4 or crossfader
MIDI
1
START
STOP
Button
Button
MIDI assignment map
Switch
TIME
Fader Start
Transmitted data
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
0-127
—
—
TIME value (When FLANGER, PHASER
or FILTER is selected, the value is halved.
When a negative value is selected, it is set
to a positive value.)
0-127
Sends the [X-PAD] position information.
MIDI LFO
QUANTIZE
SOUND COLOR FX
Trigger/Toggle
2
2
2
2
2
2
2
2
—
Trigger/Toggle
—
CH SELECT
MIC
MIDI assignment
CC 034
CC 035
CC 036
CC 037
CC 038
CC 039
CC 040
CC 041
CC 118
Note 118
CC 013
BEAT EFFECTS
BEAT EFFECTS
Type
Switch
Switch
Switch
Switch
Switch
Switch
Switch
Switch
Control
Button
Switch
CH1
CH2
CH3
CH4
MIC
CF.A
CF.B
MASTER
1 When turning one button on switches another button from on to off, MIDI on and off messages are sent from the two buttons.
When there is no button that switches off, only the MIDI on message is sent from the button that was pressed.
2 When switched from one position to another position, the MIDI ON and OFF signals are sent respectively from both positions.
— When the [START/STOP] button is pressed for over 1 second, MIDI messages corresponding to the positions of the buttons, faders and controls are sent in a bundle (Snapshot).
The MIDI Snapshot sends all MIDI messages other than MIDI start and MIDI stop.
3 Operation differs depending on the setting of the [CROSS FADER ASSIGN (A, THRU, B)] selector switch.
— When the [CROSS FADER ASSIGN (A, THRU, B)] selector switch is set to [THRU]: MIDI messages are sent when the [FADER START] button is set to [ON] and the channel fader is moved away
from you from the nearest position towards you and when it is moved back to the nearest position towards you.
— When the [CROSS FADER ASSIGN (A, THRU, B)] selector switch is set to [A]: MIDI messages are sent when the [FADER START] button is set to [ON] and the crossfader is moved from the far
edge of the [B] side and when it is moved back to the far edge of the [B] side.
— When the [CROSS FADER ASSIGN (A, THRU, B)] selector switch is set to [B]: MIDI messages are sent when the [FADER START] button is set to [ON] and the crossfader is moved from the far
edge of the [A] side and when it is moved back to the far edge of the [A] side.
En
23
Changing the settings
About the auto standby function
1 Press the [ON/OFF (UTILITY)] button for over 1 second.
The [USER SETUP] mode setting screen is displayed.
! To display the [CLUB SETUP] mode setting screen, first turn this unit’s power off,
then press the [POWER] button while pressing the [ON/OFF (UTILITY)] button.
When [Auto Standby] is set to [ON], the standby mode is set automatically if 4
hours pass with all of the conditions shown below met.
— That none of this unit’s buttons or controls are operated.
— That no audio signals of –10 dB or greater are input to this unit’s input terminals.
— That no PRO DJ LINK connections are made.
! When the [LFO FORM (WAKE UP)] button is pressed, the standby mode is
canceled.
! This unit is shipped with the auto standby function turned on. If you do not want
to use the auto standby function, set [Auto Standby] to [OFF].
2 Press the [BEAT c, d] button.
Select the setting item.
3 Press the [TAP] button.
The screen switches to the setting item’s setting value change screen.
4 Press the [BEAT c, d] button.
Change the setting value.
About the talk over function
5 Press the [TAP] button.
Enter the setting value.
The previous screen reappears.
! To return to the previous screen without changing the settings, press the
[QUANTIZE] button.
The talk over function has the two modes described below.
—[ADV] (advanced talk over): The mid-range only of the sound of channels other
than the [MIC] channel is attenuated according to the [Talk Over LEVEL] setting
value and output.
6 Press the [ON/OFF (UTILITY)] button.
dB
Close the [USER SETUP] mode setting screen.
! To close the [CLUB SETUP] mode setting screen, press the [POWER] button to
turn this unit’s power off.
Frequency
—[NOR] (normal talk over): The sound of channels other than the [MIC] channel is
attenuated according to the [Talk Over LEVEL] setting value and output.
dB
Frequency
Setting preferences
*: Setting upon purchase
Mode
Options settings
USER SETUP
CLUB SETUP
Screen display
Setting value
Descriptions
Fader Start
MIDI CH
MIDI Button Type
Talk Over Mode
F.S.
MIDI CH
MIDI BT
TLK MOD
Turns the Fader Start function on and off all at once.
Sets the MIDI channel.
Selects the MIDI signal transmission mode, [TGL (TOGGLE)] or [TRG (TRIGGER)].
Selects the talk over function’s mode, [ADV(ADVANCED)] or [NOR(NORMAL)].
Talk Over LEVEL
TLK LVL
ON, OFF*
1* to 16
TGL*, TRG
ADV*, NOR
–6 dB, –12 dB,
–18 dB*, –24 dB
–19 dB*, –15 dB,
–10 dB, –5 dB
Digital Master Out
Level
Digital Master Out
Sampling Rate
MASTER ATT.
Auto Standby
Mic Output To Booth
Monitor
DOUT LV
Sets the talk over function’s sound attenuation level.
Sets the maximum level of the sound output from the [DIGITAL MASTER OUT] terminals.
1
DOUT FS
48 kHz, 96 kHz*
Sets the digital signal’s sampling rate.
MST ATT
AUTOSTB
–6 dB, –3 dB, 0 dB*
ON*, OFF
Sets the attenuation level of the sound output from the [MASTER1] and [MASTER2] terminals.
Turns the auto standby function on and off.
MIC BTH
ON*, OFF
PC UTILITY
PC UTLY
ON, OFF*
Peak Limiter
Factory Reset
PKLIMIT
INITIAL
ON*, OFF
YES, NO*
Sets whether or not to output the microphone’s audio signals from [BOOTH] terminals.
Sets whether or not to launch the computer’s setting utility software automatically when a USB cable is
connected.
Lessens sudden, unpleasant digital clipping of the master output.
Restores all the settings to their factory defaults.
1 Note that the output sound may be distorted even if the master level indicator does not light up to the very top.
About the setting utility software
The setting utility can be used to make the checks and settings described below.
— Checking the status of this unit’s input selector switches
— Setting the audio data output from this unit to the computer
— Adjusting the buffer size (when using Windows ASIO)
— Checking the version of the driver software
Displaying the setting utility
For Windows
Click [Start] menu > [All Programs] > [Pioneer] > [DJM-900SRT] > [DJM-900SRT
Settings Utility].
24
En
For Mac OS X
Click [Macintosh HD] icon > [Application] > [Pioneer] > [DJM-900SRT] > [DJM900SRT Settings Utility].
Checking the status of this unit’s input selector
switches
Display the setting utility before starting.
Click the [MIXER INPUT] tab.
Adjusting the buffer size (when using Windows
ASIO)
If an application using this unit as the default audio device (DJ software, etc.) is running, quit that application before adjusting the buffer size.
Display the setting utility before starting.
Click the [ASIO] tab.
When Serato DJ is running and using this unit as the default audio device, set the
audio data output in Serato DJ.
Display the setting utility before starting.
1 Click the [MIXER OUTPUT] tab.
! If the buffer size is made large, drops in audio data (breaks in the sound)
occur less easily, but the time lag due to the delay in the transfer of the audio
data (latency) increases.
Changing the settings
Setting the audio data output from this unit to
the computer
Checking the version of the driver software
Display the setting utility before starting.
Click the [About] tab.
2 Click the [Mixer Audio Output] pull-down menu.
Select and set the audio data to be output to the computer from the flow of audio
signals inside this unit.
CH1
CH2
CH3
CH4
CH1 Control Tone
1
PHONO
CH1 Control Tone
CD/LINE1
CH1 Control Tone
DIGITAL1
CH2 Control Tone
1
PHONO
CH2 Control Tone
CD/LINE1
CH2 Control Tone
DIGITAL1
CH3 Control Tone
1
PHONO
CH3 Control Tone
CD/LINE1
CH3 Control Tone
DIGITAL1
CH4 Control Tone
1
PHONO
CH4 Control Tone
CD/LINE1
CH4 Control Tone
DIGITAL1
Post CH1 Fader2
Post CH2 Fader2
Post CH3 Fader2
Post CH4 Fader2
Cross Fader A
2
Cross Fader A
2
Cross Fader A
2
Cross Fader A
2
Cross Fader B2
Cross Fader B2
Cross Fader B2
Cross Fader B2
MIC
MIC
MIC
MIC
MIX (REC OUT)
2
MIX (REC OUT)
2
MIX (REC OUT)
2
MIX (REC OUT)
2
1 The audio data is output with the same volume at which it is input to this unit, regardless of
the [USB Output Level] setting.
2 When using for applications other than recording, pay attention to the DJ application’s settings so that no audio loops are generated. If audio loops are generated, sound may be input
or output at unintended volumes.
Checking the latest information on the
driver software
For the latest information on the driver software for exclusive use with this unit, visit
our website shown below.
http://pioneerdj.com/support/
! Operation cannot be guaranteed when multiple units of this mixer are connected to a single computer.
3 Click the [USB Output Level] pull-down menu.
Adjust the volume of the audio data output from this unit.
! The [USB Output Level] setting is applied equally to all audio data. However,
when 1 on the table at step 2 is selected, the audio data is output with the same
volume at which it is input to this unit.
! If not enough volume can be achieved with the DJ software’s volume adjustment
alone, change the [USB Output Level] setting to adjust the volume of the audio
data output from this unit. Note that the sound will be distorted if the volume is
raised too high.
En
25
Additional information
Troubleshooting
! Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points below. Sometimes the
trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified after checking the items
below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
! The player may not operate properly due to static electricity or other external influences. In such cases, normal operation may be restored by unplugging the power cord
then plugging it back in.
Problem
Check
Remedy
The power is not turned on.
Is the power cord properly connected?
Plug in the power cord to an AC outlet.
No sound or small sound.
Is the input selector switch set to the proper position?
Switch the input selector switch to switch the channel’s input source. (page 14)
Are the connection cables properly connected?
Connect the connection cables properly. (page 11)
Are the terminals and plugs dirty?
Clean the terminals and plugs before making connections.
Is [MASTER ATT.] set to [–6 dB], etc.?
At the [USER SETUP] screen, switch [MASTER ATT.]. (page 24)
Digital sound cannot be output.
Is the digital audio output’s sampling frequency (fs) suited
for the specifications of the connected device?
On the [CLUB SETUP] screen, set [Digital Master Out Sampling Rate] according to the
specifications of the connected equipment. (page 24)
Distorted sound.
Is the sound level output from the [MASTER] channel
appropriately set?
Adjust the [MASTER LEVEL] control so that the master channel level indicator lights at
around [0 dB] at the peak level. (Page 14)
Set [MASTER ATT.] to [–3 dB] or [–6 dB]. (page 24)
Can’t crossfade.
Can’t fader start a DJ player.
Is the level of audio input to each channel properly set?
Adjust the [TRIM] control so that the channel level indicator lights at about [0 dB] at the peak
level. (Page 14)
Are the [CROSS FADER ASSIGN (A, THRU, B)] selector
switches properly set?
Set the [CROSS FADER ASSIGN (A, THRU, B)] selector switches for the different channels
properly. (Page 14)
Is [FADER START] set to [OFF]?
At the [USER SETUP] screen, set [FADER START] to [ON]. (page 24)
Is the DJ player properly connected to the [LINK] terminal?
Connect the DJ player to the [LINK] terminal properly using a LAN cable. (page 11)
Are the audio cables properly connected?
Connect this unit’s audio input terminals and the DJ player’s audio output terminals by audio
cable. (page 11)
Is the DJ player’s player number properly set?
Set the DJ player’s player number to the same number as the channel to which the audio
cable is connected.
[BEAT EFFECTS] does not work.
Is the effect channel selector switch set to the proper
position?
Turn the effect channel selector switch to select the channel to which you want to apply the
effect.
[SOUND COLOR FX] does not work.
Is the [COLOR] control set to an appropriate position?
Turn the [COLOR] control clockwise or counterclockwise. (page 16)
Can’t use an external effector.
Is the [ON/OFF] button for [BEAT EFFECTS] set to [ON]?
Press the [ON/OFF] button for [BEAT EFFECTS] to set [SND/RTN] to [ON]. (page 16)
Is the external effector properly connected to the [SEND]
or [RETURN] terminal?
Connect the external effector to the [SEND] and [RETURN] terminals. (page 11)
Distorted sound from an external effector.
Is the external effector’s audio output level set to an
appropriate level?
Adjust the external effector’s audio output level.
Tempo (BPM) cannot be measured or
measurement value of tempo (BPM) is
implausible.
Is the audio input level too high or too low?
Adjust the [TRIM] control so that the channel level indicator lights at about [0 dB] at the peak
level. (Page 14)
Measured tempo (BPM) differs from tempo
indicated on CD.
—
The values may differ slightly due to the different ways in which the BPM is measured.
MIDI sequencer does not synchronize.
Is the MIDI sequencer’s sync mode set to Slave?
Set the MIDI sequencer’s sync mode to Slave.
Does the MIDI sequencer you are using support MIDI
timing clocks?
MIDI sequencers not supporting MIDI timing clocks cannot be synchronized.
Is the MIDI channel turned on?
Press the [ON/OFF] button for [MIDI]. (page 17)
Are the MIDI settings properly set?
To operate DJ software with this unit, this unit’s MIDI messages must be assigned to the
DJ software you are using. For instructions on assigning messages, see your DJ software’s
operating instructions.
This unit is not recognized after it has been
connected to a computer.
USB indicator is off or flashing.
Is the driver software properly installed on your computer?
Install the driver software. If it is already installed, reinstall it. (page 6)
Sound of a computer cannot be output from
this unit.
Are this unit and computer properly connected?
Connect this unit and the computer directly using the included USB cable. (page 12)
Are the audio output device settings properly set?
Select this unit with the audio output device settings. For instructions on making settings for
your application, see your application’s operating instructions.
MIDI control does not work.
For some tracks, it may not be possible to measure the tempo (BPM). Use the [TAP] button to
input the tempo manually. (page 16)
Is the input selector switch set to the proper position?
Set the input selector switch to the [USB] position. (Page 14)
Effect sound cannot be monitored even
when the [CUE] button for [BEAT EFFECTS]
is pressed.
—
The circuit that generates the echo for the [ECHO], [REVERB], [ROLL], [SLIP ROLL] and
[REV ROLL] effect sounds is positioned after the effect circuit, so the effect sound cannot be
monitored. This is not a malfunction.
Sound is distorted when an analog player is
connected to this unit’s [PHONO] terminals.
Or, lighting of the channel level indicator
does not change even when the [TRIM]
control is turned.
Have you connected an analog player with a built-in phono
equalizer?
Is an audio interface for computers connected between
the analog player and this unit?
Connect the analog player with built-in phono equalizer to the [CD/LINE] terminals. (page 11)
If the analog player with built-in phono equalizer has a PHONO/LINE selector switch, switch
it to PHONO.
If the output of the audio interface for computers is line level, connect it to the [CD/LINE]
terminals. (page 11)
If the analog player has a PHONO/LINE selector switch, switch it to PHONO.
26
En
Block Diagram
MIC1
MIC1 LEVEL
MIC2
SRC
ADC
PHONO
Control Tone
LAN
ADC
DIGITAL
CH2
DAC
CH1_Analog
ADC
PHONO
Control Tone
MASTER
ADC
BOOTH
D SP
TRIM
REC
SEND
BOOTH
MUTE
REC
MUTE
SEND
USB1/2
DIR
Additional information
DAC
RETURN
ADC
DIGITAL
MUTE
DAC
CH4_Analog
ADC
Control Tone
MASTER 2
DAC
CH3_Analog
PHONO
MUTE
CH2_Analog
DIR
CH3
PHONES
TRIM
DIGITAL
SRC
CH_1_Digital/USB1/2
TRIM
CD/LINE
CH4
PHONES
DAC
Digital MASTER
MIC
CD/LINE
DIT
MASTER 1
DIR
CD/LINE
ETHER SW IC
DIGITAL
MASTER
TRIM
CD/LINE
CH1
LAN
I/Fμ com
Ether
ADC
MIC2 LEVEL
Control Tone
ADC
DIGITAL
USB3/4
CH_2_Digital/USB3/4
ADC
PHONO
CH_3_Digital/USB5/6
USB5/6
CH_4_Digital/USB7/8
USB7/8
SRC
SRC
DIR
ADC
SRC
CH1 Digital IN
CH2 Digital IN
CH3 Digital IN
CH4 Digital IN
RETURN
USB
CH1 USB1/2 IN
SRC
USB
Type B
CH2 USB3/4 IN
I/Fμ com
USB
SRC
CH3 USB5/6 IN
SRC
CH4 USB7/8 IN
SRC
Control Tone
Control Tone
Control Tone
Control Tone
CH1 USB1/2 OUT
CH2 USB3/4 OUT
CH3 USB5/6 OUT
CH4 USB7/8 OUT
CHx in
Analog_PHONO
Phono
AMP
Level meter CHx
BPM Detect CHx Select
CH Fader
SOUND 3Band BEAT SOUND BEAT
CUE
EQ/
COLOR
COLOR
EFFECT ISOLATOR EFFECT EFFECT EFFECT Monitor
CHx
CHx
CHx
CHx
CHx
CHx
Analog_CD LINE
Digital Trim
Send/
Return
CHx
2posi
Digital/USB
Booth
Level
Post CHx Fader
CHx Control Tone
CHx _CUE
Booth Out
MIC_Out
SOUND BEAT
COLOR
EFFECT EFFECT
CHx
CHx
CH
Fader
Curve
Switch
SEL
CF Assign
Thru
CF A
CF B
3posi
MIC Output
to Booth Monitor
On/Off SW
MIX (REC OUT)
Master
Level
3posi
CH1-4 COMMON
TalkOver ON/OFF
LINK in
Link
CUE
Link_CUE
Return in
Send out
BEAT
Effect
(SND/RTN)
Assign A
CHx
Assign B
CHx
MIC1/2 in
Cross
Fader
Curve
Switch
3posi
BPM Detect CF B
2Band
MIC EQ
MIC1,2
MIC1,2 COMMON
MIC
FILTER
MIC In
Level
detect
TalkOver ON/OFF
[BEAT EFFECT (SND/RTN)]
Effect CH Select
CHx
CF A/B
MIC
Master
Return Level
Assign Thru
BPM Detect CF A
CH1-4
Cross
Fader
BEAT
EFFECT
CF A
Send/
Return
Cross Fader A
CF A
BEAT
EFFECT
CF B
Send/
Return
CF B
SEND Out
No Cable
Effect SW
RETURN
SEL
Cable Exist
CableCheck
Effect CH Select
Effect Out
CHx
CF A/B
MIC
Master
Effect_CUE
MIC 1,2
MIX
REC out
Level meter Master
MICDetect
Monitor
SW
BPM
Master
BEAT
EFFECT
Master
Send/
Return
Master
Master
Balance
Master
Mono/
STEREO
2posi
Talk Over
Mode
Advanced
/Normal
Effect_CUE
MIC
Off
On
TalkOver
3posi
[BEAT EFFECT(Others)]
Effect CH Select
BEAT
CHx
EFFECT
CF A/B
Processing
MIC
Master
BEAT
EFFECT
MIC
Send/
Return
MIC
Effect SW
Level Depth
Master
Balance
Link_CUE
Master_CUE
Digital out
Master
Limiter
Master
H.P. out
Talk
Over
Level
4para
CHx Control Tone
Boost
Post CHx Fader
Cross Fader B
Mono Split/
Stereo
SWITCH
& MIXING
HP Level
USB Common out
Mixer
Audio
Output
Select
Cross Fader A
CHx_CUE
BPM Detect MIC
ATT
Master_CUE
Talk
Over
2para
Cross Fader B
Boost
Master
CUE
MIC
MIX (REC OUT)
CH1-4 COMMON
MIC_Out
Effect CH Select
Effect Out
CHx
CF A/B
MIC
Master
Effect_CUE
[Mono Split / Stereo SWITCH & MIXING]
CHx Cue On/Off SW
CHx_CUE
CUE
Mixing
Effect Cue On/Off SW
Effect_CUE
Link Cue On/Off SW
Link_CUE
Master Cue On/Off SW
Master_CUE
MIXING
Master
Mixing
L
Mono Split
R
SEL
L
SEL
H.P. MIX L Out
Stereo
MONO SPLIT/
STEREO SWITCH
2posi
R
Mono Split
Stereo
H.P. MIX R Out
En
27
Acquiring the manual
The operating instructions may be in a file in PDF format. Adobe® Reader® must
be installed to read files in PDF format. If you do not have Adobe Reader, please
install it from the download link on the CD-ROM’s menu screen.
Downloading the latest versions of the
operating instructions and the Quick Start
Guide - Serato DJ Edition
1 Insert the CD-ROM into the computer’s CD drive.
The CD-ROM menu is displayed.
If the CD-ROM’s menu does not appear when the CD-ROM is inserted, perform the
operations below.
! For Windows
From the [Start] menu – [Computer] (or [My Computer]), open the CD drive
and double-click the [CD_menu.exe] icon.
! For Mac OS X
In Finder, double-click the [CD_menu.app] icon directly.
2 When the CD-ROM’s menu is displayed, select [DJM900SRT: Download the Operating Instructions (PDF file)], then
click [Start].
3 “An internet environment is required to access the site.
Connected to the internet?” is displayed. Click [Yes].
The web browser is launched and the Pioneer DJ support site is displayed.
http://pioneerdj.com/support/
4 On the Pioneer DJ support site, click “Manuals” under
“DJM-900SRT”.
5 From the download page, click the language for the
documents you require.
Downloading of the operating instructions/Quick Start Guide - Serato DJ Edition
starts.
Downloading the Serato DJ software manual
1 Insert the CD-ROM into the computer’s CD drive.
The CD-ROM menu is displayed.
If the CD-ROM’s menu does not appear when the CD-ROM is inserted, perform the
operations below.
! For Windows
From the [Start] menu – [Computer] (or [My Computer]), open the CD drive
and double-click the [CD_menu.exe] icon.
! For Mac OS X
In Finder, double-click the [CD_menu.app] icon directly.
2 When the CD-ROM’s menu is displayed, select [Serato DJ:
Download the Software Manual (PDF file)], then click [Start].
3 “An internet environment is required to access the site.
Connected to the internet?” is displayed. Click [Yes].
The web browser is launched and the Pioneer DJ support site is displayed.
4 Click [Software Info] under [DJM-900SRT] on the Pioneer DJ
support site.
[Serato DJ Support Information] is displayed.
5 Click the link to the Serato DJ download page.
The Serato DJ download page is displayed.
http://serato.com/
6 Log in to your “Serato.com” user account.
Input the e-mail address and password you have registered to log in to “Serato.com”.
7 From “More Downloads” on the right side of the download
page, click “Serato DJ x.x User Manual”.
Downloading of the Serato DJ software manual starts.
28
En
About trademarks and registered
trademarks
! Pioneer and rekordbox are trademarks or registered trademarks of the PIONEER
CORPORATION.
! Microsoft, Windows and Windows Vista are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
! Apple, Macintosh and Mac OS are trademarks of Apple Inc., registered in the
U.S. and other countries.
! ASIO is a trademark of Steinberg Media Technologies GmbH.
! Serato DJ is a registered trademark of Serato Audio Research Ltd., registered in
the U.S. and other countries.
The names of companies and products mentioned herein are the trademarks of their
respective owners.
Specifications
— CONTROL CD
See the information on the Pioneer DJ support site
(http://pioneerdj.com/support/).
General
Power requirements................................................................................. AC 120 V, 60 Hz
Power consumption....................................................................................................42 W
Power consumption (standby)..................................................................................0.4 W
Main unit weight......................................................................................... 7.1 kg (15.7 lb)
Max. dimensions........................................ 331 mm (W) × 107.9 mm (H) × 404 mm (D)
(13 in. (W) × 4.2 in. (H) × 15.9 in. (D))
Tolerable operating temperature............................. +5 °C to +35 °C (+41 °F to +95 °F)
Tolerable operating humidity...........................................5 % to 85 % (no condensation)
Audio Section
Additional information
Sampling rate .......................................................................................................... 96 kHz
MASTER D/A converter........................................................................................... 32 bits
Other A/D and D/A converters................................................................................ 24 bits
Frequency characteristic
CD/LINE................................................................................................20 Hz to 20 kHz
S/N ratio (rated output)
PHONO................................................................................................................88 dB
CD/LINE..............................................................................................................105 dB
MIC1, MIC2..........................................................................................................84 dB
Total harmonic distortion (CD/LINE — MASTER1)............................................. 0.005 %
Standard input level / Input impedance
PHONO.................................................................................................–52 dBu/47 kW
CD/LINE.................................................................................................–12 dBu/47 kW
MIC1, MIC2.............................................................................................–52 dBu/8 kW
RETURN.................................................................................................–12 dBu/47 kW
Standard output level / Load impedance / Output impedance
MASTER1.........................................................................+8 dBu/10 kW/5 W or lower
MASTER2.......................................................................+2 dBu/10 kW/22 W or lower
REC OUT......................................................................... –8 dBu/10 kW/22 W or lower
BOOTH........................................................................... +8 dBu/10 kW/1 kW or lower
SEND............................................................................. –12 dBu/10 kW/1 kW or lower
PHONES..........................................................................+8.5 dBu/32 W/1 W or lower
Rated output level / Load impedance
MASTER1............................................................................................ +26 dBu/10 kW
MASTER2............................................................................................ +22 dBu/10 kW
Crosstalk (LINE).........................................................................................................82 dB
Channel equalizer characteristic
HI......................................................................................... –26 dB to +6 dB (13 kHz)
MID........................................................................................ –26 dB to +6 dB (1 kHz)
LOW...................................................................................... –26 dB to +6 dB (70 Hz)
Microphone equalizer characteristic
HI....................................................................................... –12 dB to +12 dB (10 kHz)
LOW.................................................................................. –12 dB to +12 dB (100 Hz)
Input / Output terminals
PHONO input terminal
RCA pin jacks.......................................................................................................4 sets
CD/LINE input terminal
RCA pin jacks.......................................................................................................4 sets
MIC1 input terminal (XLR/TRS)
XLR connector/phone jack (Ø 6.3 mm)............................................................... 1 set
MIC2 input terminal (TRS)
Phone jack (Ø 6.3 mm)......................................................................................... 1 set
RETURN Input terminals (TS)
Phone jack (Ø 6.3 mm)......................................................................................... 1 set
DIGITAL IN coaxial input terminal
RCA pin jacks.......................................................................................................4 sets
MASTER output terminal
XLR connector...................................................................................................... 1 set
RCA pin jacks........................................................................................................ 1 set
BOOTH output terminal (TRS)
Phone jack (Ø 6.3 mm)......................................................................................... 1 set
REC OUT output terminal
RCA pin jacks........................................................................................................ 1 set
SEND output terminal (TS)
Phone jack (Ø 6.3 mm)......................................................................................... 1 set
DIGITAL MASTER OUT coaxial output terminal
RCA pin jacks........................................................................................................ 1 set
MIDI OUT terminal
5P DIN................................................................................................................... 1 set
PHONES output terminal
Stereo phone jack (Ø 6.3 mm)............................................................................. 1 set
USB terminal
B type..................................................................................................................... 1 set
LINK terminal
LAN terminal (100Base-TX).................................................................................. 1 set
! The specifications and design of this product are subject to change without
notice.
! If you require a new CONTROL CD due to wear, breakage, etc., see below.
Note that this part is expendables and not covered by the warranty, even within
the warranty period.
En
29
30
En
PIONEER ELECTRONICS (USA) INC.
LIMITED WARRANTY
WARRANTY VALID ONLY IN THE U.S.A. AND CANADA
WARRANTY
Pioneer Electronics (USA) Inc. (PUSA) warrants that products distributed by PUSA in the U.S.A. and Canada that fail to function properly under normal use due to a manufacturing
defect when installed and operated according to the owner ’s manual enclosed with the unit will be repaired or replaced with a unit of comparable value, at the option of PUSA,
without charge to you for parts or actual repair work. Parts supplied under this warranty may be new or rebuilt at the option of PUSA.
THIS LIMITED WARRANTY APPLIES TO THE ORIGINAL OR ANY SUBSEQUENT OWNER OF THIS PIONEER PRODUCT DURING THE WARRANTY PERIOD PROVIDED THE
PRODUCT WAS PURCHASED FROM AN AUTHORIZED PIONEER DISTRIBUTOR/DEALER IN THE U.S.A. OR CANADA. YOU WILL BE REQUIRED TO PROVIDE A SALES
RECEIPT OR OTHER VALID PROOF OF PURCHASE SHOWING THE DATE OF ORIGINAL PURCHASE OR, IF RENTED, YOUR RENTAL CONTRACT SHOWING THE PLACE
AND DATE OF FIRST RENTAL. IN THE EVENT SERVICE IS REQUIRED, THE PRODUCT MUST BE DELIVERED WITHIN THE WARRANTY PERIOD, TRANSPORTATION
PREPAID, ONLY FROM WITHIN THE U.S.A. AS EXPLAINED IN THIS DOCUMENT. YOU WILL BE RESPONSIBLE FOR REMOVAL AND INSTALLATION OF THE PRODUCT.
PUSA WILL PAY TO RETURN THE REPAIRED OR REPLACEMENT PRODUCT TOYOU WITHIN THE U.S.A.
PRODUCT WARRANTY PERIOD
DJ Audio and Video
...................................................................................................................................................................................
Parts
Labor
1 Year
1 Year
The warranty period for retail customers who rent the product commences upon the date product is first put into use (a) during the rental period or (b) retail sale, whichever occurs first.
WHAT IS NOT COVERED
IF THIS PRODUCT WAS PURCHASED FROM AN UNAUTHORIZED DISTRIBUTOR, THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTY
OF MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND THIS PRODUCT IS SOLD STRICTLY “AS IS” AND “WITH ALL FAULTS".
PIONEER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL AND/OR INCIDENTAL DAMAGES.
THIS WARRANTY DOES NOT APPLY IF THE PRODUCT HAS BEEN SUBJECTED TO POWER IN EXCESS OF ITS PUBLISHED POWER RATING.
Additional information
THIS WARRANTY DOES NOT COVERTHE CABINET OR ANY APPEARANCE ITEM, USER ATTACHED ANTENNA, ANY DAMAGETO RECORDS OR RECORDINGTAPES OR DISCS, ANY
DAMAGE TO THE PRODUCT RESULTING FROM ALTERATIONS, MODIFICATIONS NOT AUTHORIZED IN WRITING BY PIONEER, ACCIDENT, MISUSE OR ABUSE, DAMAGE DUE TO
LIGHTNING ORTO POWER SURGES, SUBSEQUENT DAMAGE FROM LEAKING, DAMAGE FROM INOPERATIVE BATTERIES, ORTHE USE OF BATTERIES NOT CONFORMINGTOTHOSE
SPECIFIED INTHE OWNER’S MANUAL.
THIS WARRANTY DOES NOT COVER THE COST OF PARTS OR LABOR WHICH WOULD BE OTHERWISE PROVIDED WITHOUT CHARGE UNDER THIS WARRANTY OBTAINED FROM
ANY SOURCE OTHERTHAN A PIONEER AUTHORIZED SERVICE COMPANY OR OTHER DESIGNATED LOCATION. THISWARRANTY DOES NOT COVER DEFECTS OR DAMAGE CAUSED
BYTHE USE OF UNAUTHORIZED PARTS OR LABOR OR FROM IMPROPER MAINTENANCE.
ALTERED, DEFACED, OR REMOVED SERIAL NUMBERS VOID THIS ENTIRE WARRANTY
NO OTHER WARRANTIES
PIONEER LIMITS ITS OBLIGATIONS UNDER ANY IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, TO A PERIOD NOT TO EXCEED THE WARRANTY PERIOD. NO WARRANTIES SHALL APPLY AFTER THE WARRANTY PERIOD.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND SOME STATES DO NOT ALLOW THE EXCLUSIONS OR LIMITATIONS
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
TO OBTAIN SERVICE
PUSA has appointed a number of Authorized Service Companies throughout the U.S.A. and Canada should your product require service. To receive warranty service you
need to present your sales receipt or, if rented, your rental contract showing place and date of original owner’s transaction. If shipping the unit you will need to package it
carefully and send it, transportation prepaid by a traceable, insured method, to an Authorized Service Company. Package the product using adequate padding material to
prevent damage in transit. The original container is ideal for this purpose. Include your name, address and telephone number where you can be reached during business
hours.
On all complaints and concerns in the U.S.A. and Canada call Customer Support at 1-800-872-4159.
For hook-up and operation of your unit or to locate an
Authorized Service Company, please call or write:
CUSTOMER SUPPORT
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1720
LONG BEACH, CALIFORNIA 90801
1-800-872-4159
http://www.pioneerelectronics.com
DISPUTE RESOLUTION
Following our response to any initial request to Customer Support, should a dispute arise between you and Pioneer, Pioneer makes available its Complaint Resolution Program
to resolve the dispute. The Complaint Resolution Program is available to you without charge. You are required to use the Complaint Resolution Program before you exercise
any rights under, or seek any remedies, created by Title I of the Magnuson-Moss Warranty-Federal Trade Commission Improvement Act, 15 U.S.C. 2301 et seq.
To use the Complaint Resolution Program call 1-800-872-4159 and explain to the customer service representative the problem you are experiencing, steps you have taken
to have the product repaired during the warranty period and the name of the authorized Distributor/Dealer from whom the Pioneer product was purchased. After the complaint
has been explained to the representative, a resolution number will be issued. Within 40 days of receiving your complaint, Pioneer will investigate the dispute and will either:
(1) respond to your complaint in writing informing you what action Pioneer will take, and in what time period, to resolve the dispute; or (2) respond to your complaint in writing
informing you why it will not take any action.
RECORD THE PLACE AND DATE OF PURCHASE FOR FUTURE REFERENCE
Model No. ____________________________________________ Serial No. _________________________________________ Purchase Date ______________________
Purchased From _____________________________________________________________________________________________________________________________
KEEP THIS INFORMATION AND YOUR SALES RECEIPT IN A SAFE PLACE
UCP0212
En
31
To register your product, find the nearest authorized service location, to
purchase replacement parts, operating instructions, or accessories,
please go to one of following URLs :
Pour enregistrer votre produit, trouver le service après-vente agréé le plus
proche et pour acheter des pièces de rechange, des modes d’emploi ou
des accessoires, reportez-vous aux URL suivantes :
In the USA & Canada/Aux Etats-Unis & Canada
http://www.pioneerelectronics.com
S018_B1_EnFr_PSV
© 2013 PIONEER CORPORATION.
All rights reserved.
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1720, Long Beach, California 90801-1720, U.S.A. TEL: (800) 421-1404
K002_PSV_CU
Printed in
<DRB1719-A>
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement