Epson LQ-1010 User manual

Epson LQ-1010 User manual
Add to My manuals

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Manual
Epson LQ-1010 User manual | Manualzz

FCC COMPLIANCE STATEMENT FOR AMERICAN USERS

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal

Communications Commission helpful: “Television Interference Handbook.” This booklet is available from the U.S. Government Printing Office, Washington DC 20402. Stock No. 004-000-

00450-7.

The

connection of a non-shielded equipment interface cable to this equipment will invalidate the

FCC Certification of this device and may cause interference levels that exceed the limits established by the

FCC for this equipment. If this equipment has more than one interface connector, do not

leave cable connected to unused interfaces.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical, photocopying, recording, or otherwise, without the prior written permission of Epson America, Inc. No patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this book, Epson America, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information and contained herein.

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’ émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectriques édicté par le Ministère des Communications du Canada.

Epson and Epson ESC/P are registered trademarks of Seiko Epson Corporation.

IBM is a registered trademark of International Business Machines Corporation.

SmartPark is a trademark of Epson America, Inc.

Copyright © 1989 by Epson America, Inc.

Torrance, California

ii

1.

IMPORTANT SAFETY INSTRUCTIONS

Read all of these instructions and save them for later reference.

2.

3.

4.

5.

Follow all warnings and instructions marked on the product.

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Do not use this product near water.

Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.

6.

Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.

This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided.

7. This product should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.

8. This product is equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.

9. Do not locate this product where the cord will be walked on.

i i i

10.

If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the extension cord do

not

exceed the extension cord ampere rating.

Also, make sure

that the

total of all products plugged into the wall outlet does not exceed 15 amperes.

11. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind

on

the product.

12. Except as specifically explained in the User’s Manual, do not attempt to service this product yourself. Opening or removing

those

covers that are marked “Do Not Remove” may expose you to dangerous voltage points or other risks. Refer all servicing in those compartments to service personnel.

13. Unplug this product from

the

wall outlet and refer servicing to qualified service personnel under the following conditions:

A. When the power cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

D. If the product does

not

operate normally when

the

operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore

the

product to normal operation.

E. If

the

product has been dropped or the cabinet has been damaged.

F. If

the

product exhibits a distinct change in performance, indicating a need for service.

iv

Contents

Introduction

1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1

Options and Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4

Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

Where to Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6

Chapter 1 Setting Up the Printer

1-2

Unpacking the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2

Choosing a Place for the Printer . . . . . . . . . . . . . . . . . . . . .

1-5

Assembling the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-7

Testing the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-14

Connecting the Printer to Your Computer . . . . . . . . . . . . .

1-23

Setting Up Your Application Software . . . . . . . . . . . . . . . .

1-26

Chapter 2 Paper Handling

2-1

Selecting a Paper Feeding Method . . . . . . . . . . . . . . . . . . . .

2-2

Using Single Sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-3

Using Continuous Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-7

Switching Between Continuous and Single Sheets . . . . . . . 2-16

Printing on Special Paper . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-24

Chapter 3 Using the Printer

3-1

Operating the Control Panel . . . . . . . . . . . . . . . . . . . . . . . . .

3-2

Setting the DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-6

Page Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-10

Skip Over Perforation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-11

Adjusting the Loading Position . . . . . . . . . . . . . . . . . . . . . .

3-12

Using Short Tear-Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-15

v

Selecting Typestyles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-19

Selecting an International Character Set . . . . . . . . . . . . . . .

3-22

Choosing a Character Table . . . . . . . . . . . . . . . . . . . . . . . . .

3-24

Using the Data Dump Mode . . . . . . . . . . . . . . . . . . . . . . . . .

3-26

Chapter 4 Software and Graphics

4-1

Enhancing Your Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-2

Graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-9

User-defined Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-20

Chapter 5 Using the Printer Options

5-1

The Cut Sheet Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2

The Pull Tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-21

The Multi-Font Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-34

The Interface Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-40

Chapter 6 Maintenance

6-1

Replacing the Ribbon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-5

Transporting the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-11

Chapter 7 Troubleshooting

7-1

Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-2

Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-4

Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-5

Paper Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-14

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-24

Chapter 8 Technical Specifications

8-1

Printer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-2

Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-8

Option Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-12

Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-14

vi

Chapter 9 Command Summary

9-1

Using the Command Summary . . . . . . . . . . . . . . . . . . . . . .

9-2

Commands in Numerical Order . . . . . . . . . . . . . . . . . . . . . .

9-5

Commands Arranged by Topic . . . . . . . . . . . . . . . . . . . . . .

9-8

Appendix

A-1

Proportional Width Table . . . . . . . . . . . . . . . . . . . . . . . . . . .

A-2

Character Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A-6

Glossary

Index

vii

Introduction

The Epson® LQ-1010 is an advanced 24-pin dot matrix printer combining compact design and high performance with a wide range of features.

Features

In addition to the high-quality printing and ease of operation you have come to expect from Epson printers, the LQ-1010 offers the following features:

Easy paper handling, featuring automatic single-sheet loading.

Compatibility with the Epson ESC/P

LQ-2500, and LQ-2550.

® commands used by the

LQ-500, LQ-510, LQ-800, LQ-850, LQ-1000, LQ-1050, LQ-1500,

Fast draft mode printing of up to 180 characters per second at 12 cpi (characters per second).

An improved control panel design that allows direct selection of character fonts, as well as a choice of normal or condensed printing.

The SmartPark™ paper handling system that lets you use single sheets of paper without removing the continuous paper, eliminates paper waste with short tear-off, and allows easy and accurate paper alignment.

Two built-in Letter Quality fonts (Roman and Sans Serif) for producing high-quality documents.

A 360 x 360 dot per inch graphics mode.

A micro-adjustment feature that allows you to feed the paper forward or backward to finely adjust the loading and short tear-off positions.

Introduction 1

Introduction

l l

Fourteen international character sets, a legal symbol set, an italic character table, and the Epson Extended Graphics character table.

The ability to handle a wide range of paper types, including envelopes, labels, and wide carriage computer paper.

Options and Supplies

A variety of printer options is available for use with your LQ-1010 printer. For detailed information on installing and using these options, see Chapter 5.

To locate or purchase accessories or supplies, contact your nearest

Epson dealer or call

1-800-873-7766.

l

Single-bin Cut Sheet Feeder (C806241)

The cut sheet feeder makes it possible to handle single-sheet paper easily and efficiently. Up to

150 sheets of standard bond paper can be fed automatically into the printer without reloading.

2

Introduction

Introduction l

Pull Tractor Unit

(C800141)

This option improves the performance of continuous paper handling. It is especially useful with continuous multi-part forms.

l

Multi-Font Module

(#7407-A)

The optional Multi-Font module adds to the number of fonts available in the Letter Quality mode.

l

Film Ribbon Cartridge

(#7770)

The optional film ribbon cartridge provides you with even higher quality printing than the standard fabric ribbon.

Introduction 3

Introduction

l

Interface Boards

Optional interface boards are available to supplement the printer’s built-in parallel interface. Guidelines for choosing the right interface and instructions on installing the boards are given in Chapter 5.

About This Manual

This user’s manual provides fully illustrated, step-by-step instructions on setting up and operating your Epson LQ-1010 printer,

Finding your way around

• Chapter 1 contains information on unpacking, setting up, testing, and connecting the printer. Be sure to read and follow these instructions first. Inside the back flap of this manual are illustrations of the printer in which all of the major parts are identified.

• Chapters 2 and 3 cover paper handling and general printer operation. This important information is necessary for the day-to-day operation of your printer.

4 Introduction

Introduction

l l l l

Chapter

4

shows you how to get the most from your printer. It includes advice on the use of software commands, graphics, and creating your own user-defined characters. See Chapter

9

for a useful summary of printer commands.

If the printer does not operate properly or the printed results are not what you expect, see Chapter 7 for troubleshooting instructions.

Other chapters and the appendix contain information on printer options, general maintenance, and specifications. You will also find a glossary of printer terms.

At the back of this manual is a handy Quick Reference card that contains the information you are most likely to need.

Conventions used in this manual

WARNINGS must be followed carefully to avoid damage to your printer and computer.

CAUTIONS should be followed carefully to ensure that your printer operates correctly.

Notes contain important information and useful tips on the operation of your printer.

Application Notes

Also included in the box with your printer is a booklet called

Application

Notes. It contains information on using specific software applications with your printer. Be sure to look at the booklet after you set up your printer.

Introduction 5

Introduction

Where to Get Help

Customer support and service for Epson products are provided by a network of authorized Epson dealers and Customer Care Centers throughout the United States. Epson America provides product information and support to its dealers and Customer Care Centers.

Therefore, we ask that you contact the business where you purchased your Epson product to request assistance. If the people there do not have the answer to your question, they can obtain it through our dealer support program.

Epson is confident that this policy will provide you with the assistance you need. Call the Epson Consumer Information Center at

1-800-922-8911 for the following: l l l

The location of the nearest Epson dealer

The location of the nearest Customer Care Center

Information on Epson User Groups.

6

Introduction

Chapter 1

Setting Up the Printer

Unpacking the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Checking the Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Removing the Protective Materials . . . . . . . . . . . . . . . . . . . . 1-3

Choosing a Place for the Printer . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Assembling the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Installing the Platen Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Installing the Ribbon Cartridge . . . . . . . . . . . . . . . . . . . . . . . 1-8

Attaching the Paper Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Testing the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14

Plugging in the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14

Running the Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15

If the Self Test Does Not Work . . . . . . . . . . . . . . . . . . . . . . . 1-22

Connecting the Printer to Your Computer . . . . . . . . . . . . . . . . 1-23

The Parallel Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23

Setting Up Your Application Software . . . . . . . . . . . . . . . . . . . 1-26

Choosing From a Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26

Setting Up the Printer

1-1

Unpacking the Printer

Checking the Parts

When you unpack the printer, make sure that you have all the parts shown below and that none have been damaged.

1-2

Setting Up the Printer

Unpacking the Printer

Removing the Protective Materials

The printer is protected during shipping by a locking clip. You must remove this clip before turning on the printer.

WARNING:

Be sure you have removed the locking clip before tuning

on

your printer. Turning on the printer while the clip is attached may seriously damage the mechanism.

Follow these steps to remove the locking clip.

1.

Remove the printer cover.

Setting Up the Printer

1-3

Unpacking the Printer

2. Remove the paper tension unit as shown below.

3. Remove the locking clip.

Note: Store the clip with the other packing material in case you ever need to transport your printer.

1-4 Setting up the Printer

Choosing a Place for the Printer

There are several important things to consider when selecting a place to set up your printer. Keep the following in mind:

Place the printer on a flat, hard, stable surface. A soft surface, such as a padded counter or carpeted area, will block the ventilation slots and may cause overheating.

Place the printer close enough to the computer for the printer cable to reach.

Leave adequate room around the printer to allow for easy printer operation and maintenance, and for unrestricted flow of air around the printer.

Use a grounded outlet; do not use an adapter plug.

WARNING:

Avoid locations that are subject to direct sunlight, excessive heat, moisture, or dust.

Avoid electrical outlets controlled by wall switches or automatic timers. Accidental interruption of power can wipe out information in your computer’s memory and in your printer’s memory.

Avoid using outlets that share a circuit with large motors or electrical appliances; this could cause fluctuations in line voltage.

Keep the entire computer system away from potential sources of electromagnetic interference such as loudspeakers or the base units of cordless telephones.

Setting Up the Printer 1-5

Choosing a Place for the Printer

The illustration below shows a good printer location.

Note: Before using a printer stand, read these requirements and suggestions.

l

The stand should be able to support at least twice the weight of the

LQ-1010

printer, or approximately 36 pounds

(16

kilograms).

l l l l

Never use a stand that supports the printer at an angle of more than 15 degrees from horizontal.

With a cut

sheet

feeder, your printer must be kept level.

If your paper supply is positioned below

the

printer stand, make sure there is enough

clearance

to keep the paper from catching on the underside of the stand. Also, make sure the distance between

the

stand supports is wide enough for the paper you are using.

Position your printer’s cables

so that

they do

not

interfere with paper feeding. If possible, secure the cables to the printer stand.

1-6

Setting Up the Printer

Assembling the Printer

After you’ve decided on the best place to set up your printer, the next step is to install the platen knob.

WARNING: Be sure to remove the locking clip as described in the Removing the Protective Materials section of this chapter before proceeding.

Installing the Platen Knob

The platen knob is used to feed the paper manually in the event of a paper jam or other paper feeding problem. The platen knob is packed in an indentation in the printer’s white foam packing material.

1. Insert the knob into the hole on the printer’s side and rotate it slowly until it slips onto the shaft.

Setting Up the Printer

1-7

Assembling the Printer

2. Push firmly on the platen knob until it fits against the printer case.

CAUTION: Do not use the platen knob to adjust the position of the paper. This interferes with the automatic paper loading system and may cause a paper jam.

Installing the Ribbon Cartridge

Your printer’s ribbon cartridge is designed for easy installation and removal. Before installing the ribbon cartridge, make sure the printer is turned off.

1-8 Setting Up the Printer

Install the ribbon cartridge as follows.

1. Slide the print head to the middle of the printer.

Assembling the

Printer

CAUTION:

Never move the print head while the printer is turned on because this can damage the printer. Also, if you have been using the printer, the print head may be hot; let it cool for a few minutes before touching it.

2.

Turn the ribbon-tightening knob in the direction of the arrow. This removes slack in the ribbon and makes it easier to install.

Setting Up the Printer

1-9

Assembling the Printer

3.

Hold the ribbon cartridge by its handles and push it firmly down into position, making sure the plastic hooks fit into the slots.

Note: Press

lightly on both ends of the cartridge to make sure the plastic hooks are properly seated.

4.

Use a pointed object, such as a ball point pen, to guide the ribbon between the print head and ribbon guide while you turn the ribbon-tightening knob to help feed the ribbon into place.

1-10 Setting Up the Printer

Assembling the Printer

5. Slide the print head from side to side to make sure it moves smoothly. Also check that the ribbon is not twisted or creased.

6. Fit the rear notches of the paper tension unit over the pins of the printer. Lower the unit, pressing on both sides to lock it in place.

Setting Up the Printer 1-11

Assembling the Printer

Attaching the Paper Guide

When you use single sheets, the paper guide helps to feed the paper smoothly and efficiently into the printer. Attach the paper guide using the following procedure.

1. Place the paper guide on the printer as shown below.

2. Raise the paper guide until it locks into place.

1-12

Setting Up the Printer

Assembling the Printer

Note:

To lower the paper guide, lift up slightly to release it from its locked position; then gently lower it down onto the printer.

3. Attach the printer cover by fitting the hooks on the cover into

the

notches at the front of the printer and tilting the cover back into place.

Setting Up the Printer

1-13

Testing the Printer

Now that your printer is fully assembled, you can use its built-in self test function to see that the printer is working correctly before you connect it to a computer. You should perform this test to make sure that your printer was not damaged during shipping and that the ribbon is correctly installed.

Before running the self test, you need to connect the printer to an electrical outlet and load a sheet of paper.

Plugging in the Printer

1.

Make sure that the printer is turned off.

1-14

Setting Up the Printer

Testing the Printer

2. Plug the power cable into

a

properly grounded electrical outlet.

Running the Self Test

The self test can be run in the draft or Letter Quality mode, depending on which button you hold down as you turn on the printer. Although the self test can be run with continuous paper, use single-sheet paper now because single-sheet loading is easier.

1. Make sure the printer is turned off.

2. Push the paper release lever back to the single-sheet position.

Setting Up the Printer

1-15

Testing the Printer

3. While holding down the LINE FEED button (draft mode) or FORM

FEED

button (Letter Quality mode), turn on the printer. The printer beeps several times and POWER and PAPER OUT lights come on.

4. Move the left edge guide so that it locks in place next to the guide mark.

1-16 Setting Up the Printer

Testing the Printer

5. Adjust the right edge guide to match the width of your paper. Next, slide a sheet of paper down between the edge guides until it meets resistance.

WARNING: Never run the self test using paper that is narrower than 14 inches (legal paper turned sideways) to prevent the print head from printing directly onto the platen.

6. Press the LOAD/EJECT button to load the paper.

Setting Up the Printer

1-17

Testing the Printer

7.

Press the ON LINE button to start the self test. A list of DIP switch settings is printed first, followed by a series of characters. The self test continues until the paper runs out or until you press the ON

LINE

button.

8. If the test results are satisfactory and you wish to stop the test, press the ON LINE button. If the test results are not satisfactory, see

Checking the Operation later in this chapter for possible causes and solutions.

Note:

To resume the test, press the ON LINE button once more.

1-18 Setting Up the Printer

Testing the Printer

9. If the paper is still loaded, press the LOAD/EJECT button or LINE

FEED

button to eject it. Then turn off the printer.

WARNING: five seconds before turning it back on. Turning the power on and

After turning the power off, always wait at least off rapidly can damage the printer.

Setting Up the Printer 1-19

Testing the Printer

Here is part of a typical self test printed in draft mode.

Draft mode

Country

USA

France

Germany

U.K.

Denmark

Sweden

I t a l y

Spain

Font

Roman

Sans serif

Slot,

Draft

Condensed

Invalid

SW1-1 1-2 1-3

on on on on on o f f on o f f o n on o f f o f f o f f o n o n o f f o n o f f o f f o f f o n o f f o f f o f f

SW1-4 1-5 o f f o f f on o f f o f f o n on on

SW1-6 o f f

Page length

11”

12”

Tear off mod

Invalid

V a l i d

1” Skip

Invalid

V a l i d

Auto LF

Invalid

V a l i d

Receive

buff

1kbytes

8kbytes

Graphics

pri

Note: When using the optional cut

sheet

feeder, the first page of

the

self test printout is slightly different. For details, see

the

Cut Sheet

Feeder section in Chapter 5.

1-20 Setting Up the Printer

Testing the Printer

Here is part of a typical self test printed in Letter Quality mode.

Letter Quality mode

Country

USA

France

Germany

U.K.

Denmark

Sweden

I t a l y

Spain

Font

Roman

Sans serif

S l o t

D r a f t

SW1-1 1-2 1-3 on on on on on o f f on o f f o n o n o f f o f f o f f o n o n o f f o n o f f o f f o f f o n o f f o f f o f f

SW1-4 1-5

o f f o f f on o f f o f f o n on on

Page length

11”

12”

Tear off moc

I n v a l i d

V a l i d

1"Skip

Invalid

V a l i d

Auto LF

Invalid

V a l i d

Receive buff

1kbytes

Setting Up the Printer

1-21

Testing the

Printer

If the Self Test Does Not Work

If the self test does not print properly, check the control panel and the print head area. If paper is jammed, turn off the printer. Then remove the paper using the platen knob and load a new sheet. Make sure that all packing material and shipping restraints have been removed from inside the printer. See the Removing the Protective Materials section in this chapter for information on removing the locking clip. You can also see Chapter 7 for further information.

Problem Solution

The printer sounds like it is printing, but nothing is printed.

The test did not print

when you pressed the

ON LINE button.

The ribbon may not be installed properly.

Turn off the printer, reinstall the ribbon cartridge, and then tighten the ribbon by turning the ribbon-tightening knob. Make sure the ribbon passes between the print head and ribbon guide. See page 1-10.

The ribbon may be worn. Replace the ribbon cartridge. See page 6-5.

Turn off the printer and repeat the self test.

Make sure you hold down the FORM FEED or

LINE FEED

button the entire time you are turning on the printer.

Turn off the printer and disconnect the cable from the host computer. Try the self test again.

If the printer still does not print the self test correctly, contact your Epson dealer.

1-22

Setting Up the Printer

Connecting the Printer to Your Computer

If the self test printed correctly, you are now ready to connect the printer to your computer.

If your computer has a parallel interface and you have a suitable shielded cable, you should be able to connect your printer immediately.

The steps below describe how to connect the parallel interface cable.

If your computer requires another type of interface, you need to install an optional interface board. See the Interface Boards section in

Chapter 5.

If you are not sure which type of interface cable is required, see your computer manual.

The Parallel Interface

Connect the parallel interface cable as described below:

1. Make sure that both your printer and computer are turned off.

Setting Up the Printer 1-23

Connecting the Printer to Your Computer

2. Plug the cable connector securely into the printer.

3. Squeeze the wire clips together until they lock in place on either side of the connector.

1-24

Setting Up the Printer

Connecting the Printer

to Your Computer

4. If your cable has a ground wire, connect it to the ground screw beneath the interface connector.

5. Plug the other end of the cable into the computer. If there is a ground wire at the computer end of the cable, attach it to the ground connector at the back of the computer.

Setting Up the Printer

1-25

Setting Up Your Application Software

Now that you

have

set up and tested the

LQ-1010,

sure that it works with your application programs.

you should make

Most application programs let you specify the type of printer you are using so that

the

program can take full advantage of the printer’s features. Many of these programs provide an installation or setup menu that presents a list of printers to

choose

from.

If your application program has a printer selection menu, use instructions below.

the

Choosing From a Menu

Because the family of Epson printers shares a great many commands, you can use

an

application program even if it does not list on its printer selection menu. If the

LQ-1010 the

LQ-1010 is not listed, choose one of the following printers. They are listed in order of preference.

LQ-1050

LQ-2550

LQ-2500

LQ-1000

LQ-1500

If none of these printers is listed, select the first one available on the following list:

LQ

EX

FX

LX

Rx

MX

Epson printer

Standard printer

Draft printer

To use all of the

the

program with the

LQ-1010,

features of the

LQ-1010

contact

the

available that supports the

LQ-1010,

software manufacturer to see if an update is

LQ-1010

model.

however, it is best to use a on its menu. If your program does not list

1-26 Setting Up the Printer

Chapter 2

Paper Handling

Selecting a Paper Feeding Method . . . . . . . . . . . . . . . . . . . . . . . 2-2

Using Single Sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Loading Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Reloading During Printing . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Using Continuous Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-7

Positioning Your Continuous Paper Supply . . . . . . . . . . . . . 2-7

Loading Continuous Paper . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Switching Between Continuous and Single Sheets

. . . . . . . . .

2-16

Switching to Single Sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

Switching Back to Continuous Paper . . . . . . . . . . . . . . . . . . 2-21

Printing on Special Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24

The Paper Thickness Lever . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24

Multi-part Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27

Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28

Envelopes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30

Paper Handling 2-1

Selecting a Paper Feeding Method

The paper release lever on the LQ-1010 has three positions for use with

the

various methods of paper feeding. Make sure the paper release lever is set to match the desired paper feeding method.

The lever positions are marked by three icons, as described below.

Single-sheet mode: When you load single sheets from either the paper guide or from the optional cut sheet feeder, the lever should be set all the way back to the single-sheet position.

Push tractor mode: When you load continuous paper with the built-in push tractor, the lever should be set in the middle, which is the push tractor position.

Pull tractor mode: When you load continuous paper with the optional pull tractor, the lever should be set all the way forward to the pull tractor position. Even when you use the built-in push tractor with the pull tractor, you must set the lever to this position. Select this position only if you are using the optional pull tractor.

2-2

Paper Handling

Using Single Sheets

Your printer can accommodate single sheets with a width of 7.2 inches or 182 mm to 14.3 inches or 364 mm.

If you do most of your printing on single sheets, you may find it more convenient to install the optional cut sheet feeder. This option automatically inserts a new sheet and can hold up to 150 pages. For more details, see Chapter 5.

Loading Paper

1. Push the paper release lever back to the single-sheet position.

Paper Handling 2-3

Using Single Sheets

2.

Turn on the printer. (The green POWER light should come on.)

Note: Do

not

insert paper in

the

printer before turning on the printer.

3.

Move the left edge guide so that it locks in place next to the guide mark. (You may want to change this position later, depending on the margin settings of your application program.)

2-4

Paper Handling

Using Single Sheets

4. Adjust the right edge guide to match the width of your paper. Then slide the paper down between the edge guides until it meets resistance.

5. Press the LOAD/EJECT button once to load the paper automatically.

CAUTION: Never advance the paper using the platen knob while the printer is turned on. If the platen turns without loading the paper, remove the paper and reinsert it more firmly. Then press the LOAD/EJECT button again.

Paper Handling 2-5

Using Single

Sheets

6.

Press the ON LINE button to set the printer on line. When the ON

LINE

light is lit, the printer can accept data from your computer.

You are now ready to begin printing.

Reloading During Printing

When you print a document of more than one page using single-sheet paper, the printer stops printing when it reaches the bottom of the page.

When this happens, the ON LINE light either goes off automatically or remains on, depending on your application program software. If the ON

LINE

light remains on, the first thing you should do is press the ON LINE button to take the printer off line.

Once the ON LINE light is off, remove the sheet that has just been printed (if necessary, press the LOAD/EJECT button to eject the page) and load a new sheet. Press the ON LINE button to start printing the next page and follow any additional prompts from your software. Be sure

that

the page length or form length setup in your software matches the number of lines that can be printed on your paper.

2-6

Paper Handling

Using Continuous Paper

The push tractor built into your load and operate. Its low-profile design takes up little space and can handle paper up to

16

LQ-1010

printer is remarkably easy to inches or 406 mm wide.

Positioning Your Continuous Paper Supply

An important consideration for achieving smooth and trouble-free paper feeding is the position of your paper supply.

Three ways of positioning your printer and continuous paper supply are shown below.

Paper Handling 2-7

Using Continuous Paper

Be sure to align the paper supply with the paper loaded in the tractor so that the paper feeds smoothly into the printer.

Loading Continuous Paper

1.

Be sure that the printer

is

turned off, then remove the paper guide.

2-8 Paper Handling

Using Continuous Paper

2. Set the paper release lever to the push tractor paper position, which is the middle setting. This position is marked by the icon shown in the illustration below.

3. Release the sprocket units by pulling the sprocket lock levers forward as shown below.

Paper Handling 2-9

Using

Continuous Paper.

4.

Slide the left sprocket unit until it is about

1 inch (25 mm) from the farthest left position and press the lever back to lock it in place.

5. Slide the right sprocket unit so that it roughly matches the width of your paper, but do not lock it.

2-10

Paper Handling

Using Continuous Paper

6. Move the paper support midway between the two sprocket units.

7. Open both sprocket covers.

Paper Handling 2-11

Using Continuous Paper

8. Fit the first three holes in the paper over the pins of both sprockets.

CAUTION: Make sure that your paper has a clean, straight edge before inserting it into the printer.

9. Close the sprocket covers.

2-12

Paper Handling

Using Continuous Paper

10.

Slide the right sprocket unit to a position where the paper is straight and has no wrinkles. Then lock it in place.

11. Reattach the paper guide as shown below. Then slide the edge guides apart to the sides of the paper guide as shown.

Paper Handling 2-13

Using Continuous Paper

12.

Turn on the printer. It will beep because there is no paper in the printer. Then press the LOAD/EJECT button to feed paper to the loading position.

13. Press the ON LINE button to set the printer on line so that it can accept data.

2-14

Paper Handling

Using Continuous Paper

The printer remembers the loading position and advances each page to the same position. If you need to adjust the loading position, use the micro-adjustment feature. See the section on setting the loading position in Chapter 3.

CAUTION: Never adjust the loading position using the platen knob and never turn the platen knob while the printer is turned on.

Before you begin printing, be sure to check the page length and skip over perforation settings, and readjust these settings if necessary. See the sections on page length and skip over perforation in Chapter 3.

Paper Handling

2-15

Switching Between Continuous and Single Sheets

Even with continuous paper loaded in the printer, the SmartPark feature allows you to easily switch to single-sheet printing without removing the continuous paper from the tractor.

Switching to Single Sheets

To switch from continuous paper to single sheets, follow the steps below.

1. If the printer is on line, press the ON LINE button to set the printer off line.

2-16

Paper Handling

Switching Between Continuous and Single Sheets

2. Tear off any outgoing sheets. If your printed document has not advanced past the print head, you need to press the FORM FEED button to advance your document to a point where it can be easily removed.

CAUTION: Make sure you tear off your printed document

before pressing the

LOAD/EJECT

button. Reverse-feeding several pages at a time may result in a paper jam. This is especially true for narrow paper (less

than

6 inches or

152.4

mm wide).

Paper Handling

2-17

Switching Between Continuous and Single Sheets

3.

Press the LOAD/EJECT button to feed the continuous paper backward out of the printer and into the standby position. The paper is still attached to the tractor but is no longer in the paper path.

CAUTION: Pressing the LOAD/EJECT button once may not feed the paper far back enough to reach the standby position.

If the PAPER OUT light does not come on, you need to press the LOAD/EJECT button again. With normal-width continuous paper, you can press the LOAD/EJECT button up to three times. If, however, you are using narrow paper (between 4 and 6 inches or 101.6 and 152.4 mm) you should only press

the LOAD/EJECT

button once. Also, do not use this button to eject labels.

WARNING: Never feed labels backward through the printer.

Labels can easily come off the backing sheet and jam the printer.

2-18

Paper Handling

Switching Between Continuous and Single Sheets

4.

Push the paper release lever back to the single-sheet position. This position is marked by the icon shown in the illustration below.

5. Stand the paper guide upright and adjust the edge guides to roughly match the width of your paper.

Paper Handling

2-19

Switching Between Continuous and Single Sheets

6 .

Insert a sheet of paper between the edge guides until the bottom meets resistance. Slide the edge guides to exactly match the width of your paper.

7.

Press the LOAD/EJECT button to automatically feed the single-sheet paper to the loading position. Then, press the ON LINE button to set

the

printer on line.

2-20

Paper Handling

Switching Between Continuous and Single Sheets

Switching Back to Continuous Paper

It is also easy to switch back to printing with continuous paper. Before switching to continuous paper, make sure that the single sheet is ejected and the printer is off line.

1. Slide the edge guides apart so they do not interfere with continuous paper feeding.

2. Lower the paper guide onto the printer.

Paper Handling

2-21

Switching Between Continuous and Single Sheets

3. Pull the paper release lever forward to the middle (push tractor) position for continuous paper feeding.

4. Press the LOAD/EJECT button to feed the continuous paper to the loading position.

2-22 Paper Handling

Switching Between Continuous and Single Sheets

5. Press the ON LINE button to set the printer on line so that it can accept data.

Paper Handling

2-23

Printing on Special Paper

In addition to printing on single sheets and continuous paper, your printer can also print on a wide variety of paper types, including multi-part forms, labels, and envelopes.

Before printing on special types of paper, you need to change the paper thickness setting.

WARNING: When printing on multi-part forms, labels, or envelopes, make sure that your application program settings keep the printing entirely within the printable area.

For multi-part forms and labels you should not print any closer than one-half inch from either side of the paper.

For information on the printable area for envelopes, see page

2-31.

The Paper Thickness Lever

To accommodate various thicknesses of paper, the LQ-1010 is equipped with a paper thickness lever that can be set to eight positions. These positions are identified by a scale on the printer next to the lever. (See the chart on page 2-26.)

2-24 Paper Handling

Printing on Special Paper

To change the paper thickness setting, follow these steps.

1. Make sure that the printer is turned off. Then remove the printer cover.

WARNING: If the printer has just been in use, the print head may be hot. Allow it to cool before touching it.

2. Select the paper thickness you want according to the table on the following page. For normal use, the lever should always be set to position 2 on the scale.

To help you check the position of the paper thickness lever, the orange MULTI-PART light on the control panel comes on if the lever is set to position 4 or higher.

Paper Handling

2-25

Printing on Special Paper

Paper Type

Paper (single sheets or continuous)

Thin paper

24 lb paper

Multi-part forms

2-sheet

3-sheet

Lever Position

2

2

3

3

4

4

Labels

Envelopes

Air mail

Plain

Bond (20 lb)

Bond (24 lb)

4 or 5

6

6

7

Note:

Lever position 1 is used only when the printed characters are too light. Setting the lever to position 1 when you are using thin paper may damage the print head. Also, if the lever is set to position 4 or higher, the printing speed may be reduced slightly.

2-26 Paper Handling

3. Reattach the printer cover as shown below.

Printing on Special Paper

WARNING:

Always return the lever to position 2 when you go back to printing on ordinary paper. Continuous printing with the lever set at a position higher than 2 can shorten the life of the print head. Also note that printing past the edge of envelopes, multi-part forms, labels, or thicker-than-normal paper can damage the print head.

Multi-part Forms

With the built-in tractor unit, your printer can print on continuous multi-part forms. You can use multi-part forms that have up to three parts including the original. Make sure you set the paper thickness lever to the proper position; see the table on page 2-26.

Paper Handling

2-27

Printing on Special Paper

Except for the paper thickness lever setting, you load multi-part paper the same way as continuous paper. For details, see the section on loading continuous paper in this chapter. Also see the sections on setting the loading position and page length in Chapter 3.

CAUTION:

Multi-part forms should not be used with the single-sheet feeding system or the optional cut sheet feeder.

Labels

If you need to print labels, always use labels mounted on a continuous backing sheet with sprocket holes for use with a tractor. Do not try to print labels as single sheets because labels on a shiny backing sheet almost always slip a little.

2-28 Paper Handling

Printing on Special Paper

You load labels the same way that you load continuous paper except that the paper thickness lever must be adjusted for printing labels. See the section on loading continuous paper earlier in this chapter. For the correct paper thickness setting, see the table on page

2-26.

WARNING:

Never feed labels backward through the printer.

Labels can easily peel off the backing and

Therefore,

jam the

printer.

never

use the LOAD/EJECT button to eject

labels.

Also,

never

use the short tear-off function with labels.

(Be sure to set DIP switch

2-2

to off.) If a label does become stuck in the printer, contact your Epson dealer.

Since labels are especially sensitive to temperature and humidity, always use them under normal operating conditions. Don’t leave labels loaded in the printer between jobs; they curl around the platen and may jam when you resume printing.

Paper Handling

2-29

Printing on Special Paper

Envelopes

You can feed envelopes individually using the single-sheet loading feature. Before loading envelopes, adjust the position of the paper thickness lever according to the table on page handling, see Using Single Sheets on page

2-26.

2-3.

For details on paper

When manually feeding an envelope, you may have to push it down slightly while pressing the LOAD/EJECT button to get it to feed properly.

CAUTION:

The printable area for envelopes is shown on the

next page. The print head must not go past the left or right edge of the envelope or other thick paper. Make sure that your application program page setup keeps the printing entirely within this printable area.

2-30

Paper Handling

Printing on Special Paper

CAUTION:

Envelope printing is only available at normal temperature (41°F to 95°F or 5°C to 35°C).

To make sure that the printing fits within the printable area, always print a test sample using a normal sheet of paper before printing on envelopes.

Paper Handling

2-31

Chapter 3

Using the Printer

Operating the Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Setting the DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Changing a DIP Switch Setting . . . . . . . . . . . . . . . . . . . . . . . 3-6

The DIP Switch Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

The DIP Switch Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Page Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Skip Over Perforation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Adjusting the Loading Position . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

The Loading Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Using Micro-adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

Using Short Tear-off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15

Adjusting the Tear-off Position . . . . . . . . . . . . . . . . . . . . . . . 3-16

Selecting Typestyles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

Character Fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

Condensed Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21

Selecting an International Character Set . . . . . . . . . . . . . . . . . 3-22

Choosing a Character Table . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24

Using the Data Dump Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26

Using the Printer 3-1

Operating the Control Panel

The indicator lights give you the current status of the printer. The buttons and paper handling functions let you control many of the printer settings.

Lights

MULTI-PART (orange)

On when the paper thickness lever is set to position

4 or higher. When this light is blinking, the micro-adjustment function can be used.

POWER

(green)

On when the POWER switch is on and power is supplied.

READY

(green)

On when the printer is ready to accept input data. Flickers during printing.

PAPER OUT (red)

On when the printer is out of paper or when continuous paper is in the standby position.

ON LINE (green)

On when the printer is on line and ready to accept data.

3-2 Using the Printer

Buttons

Operating the Control Panel

ON LINE

This button controls the printer’s on line and off line status. Press this button to put the printer on line or to take it off line. When the printer is on line, the ON LINE light is on and the printer can receive and print data from the computer.

FORM FEED

When the printer is off line, press this button to eject a single sheet of paper or to advance continuous paper to the top of the next page.

LINE FEED

When the printer is off line, press this button to advance the paper one line, or hold it down to advance the paper continuously.

LOAD/EJECT

This button is used to feed paper to the loading position or to eject paper that is already loaded.

Paper is ejected forward if the paper release lever is set to the single-sheet position and backward (out of the paper path) if the release lever is set to the continuous paper position.

Using the Printer 3-3

Operating the Control Panel

SelecType

FONT

This button is used to select LQ

ROMAN, LQ SANS SERIF, DRAFT

mode, or a cartridge font (if installed). The two orange indicator lights show the selected font. See Selecting Typestyles later in this chapter.

CONDENSED

This button is used to turn the condensed mode on and off. The orange indicator light is on when the printer is in the condensed mode. In the condensed mode, all characters are printed at approximately 60 percent of their normal width.

3-4

Using the Printer

Operating the Control Panel

Other control panel features

The control panel of your printer also gives you access to several special functions.

Self test:

Micro-adjustment:

Data dump:

Both a draft and Letter Quality self test function are built into the printer. The self test printout lets you check the current DIP switch settings and operating status of the printer. You can start the printer’s self test by holding down the LINE FEED button or the FORM FEED button while turning on the printer. See the section on the self test in

Chapter 1 for more information.

By pressing the FORM FEED button immediately after loading paper or when using short tear-off, you can make fine adjustments to the loading and short tear-off positions. These positions can be adjusted only while the MULTI-PART light is blinking. See the sections on adjusting the loading position and using the short tear-off function later in this chapter.

By holding down both the LINE FEED and FORM

FEED

buttons while you switch on the printer, you turn on the data dump mode. This feature allows advanced users to locate the source of communications problems between the computer and printer. See the section on using the data dump mode on page 3-26 for more information.

Using the Printer 3-5

Setting the DIP Switches

The LQ-1010 has two sets of DIP (Dual Inline Package) switches located under a small cover above the control panel. By changing the settings of these switches, you can control various printer features, such as the character set and page length. The new settings become effective when the printer is turned on, reset, or initialized.

DIP switch settings are shown in the DIP switch tables starting on page

3-7. Descriptions of all the DIP switch functions begin on page 3-9.

Changing a DIP Switch Setting

To change a DIP switch setting, first turn off the printer. Then open the

DIP switch cover and use a pointed object, such as a pen, to change the

DIP switch settings. A DIP switch is on when it is up, and off when it is down.

The new DIP switch settings take effect when the printer is turned on.

3-6 Using the Printer

Using the Printer

The DIP Switch Tables

The tables below show the settings for each DIP switch. The shaded areas show the default or factory settings.

DIP switch 1

DIP switch 2

* Required for use of user-defined (download) characters.

** When on and ESC U0 is input, multi-pass characters are printed bi-directionally.

Using the Printer 3-7

Setting the DIP Switches

Table 1 International character sets

Table 2 Font selection

Font

Roman

Sans Serif

Slot

Draft

SW1-4

SW1-5

OFF OFF

ON OFF

OFF ON

ON ON

Table 3 Character spacing

Spacing

10 cpi

12 cpi

15 cpi

Proportional

SW2-7 SW2-8

OFF OFF

ON

OFF

OFF ON

ON ON cpi: characters per inch.

3-8 Using the Printer

The DIP Switch Functions

Auto line feed

When auto line feed is on (DIP switch

2-4

on), each carriage return code (CR) is automatically followed by a line feed code (LF).

Input buffer capacity

The input buffer stores data from your computer. If you want to free your computer for other tasks while the printer prints, change the setting of switch

2-5

to 8 KB (on). Before using user-defined characters, however, be sure to set the input buffer to 1 KB (off).

Tear-off mode

When DIP switch

2-2

is on, the short tear-off mode is on. This feature automatically advances continuous paper to the tear-off position, and

then

reverse-feeds the paper to the loading position. See the section on using short tear-off later in this chapter.

CAUTION:

Do not use the short tear-off mode with labels.

Print direction of multi-pass characters

Multi-pass characters are normally printed unidirectionally. If DIP switch

2-6

is on and ESC bi-directionally.

U0

is input, multi-pass characters are printed

Using the Printer 3-9

Page Length

When the setting of DIP switch 2-1 is off, the page length is set to 11 inches, or 279.4 mm. When it is on, the page length is 12 inches, or

304.8 mm. Be sure to set the page length to match the paper you are using.

Other page lengths can be set using the commands ESC C and ESC C 0.

See the Command Summary in Chapter 9 for details.

If you are using the built-in push tractor, you can also select 8.5 inches as the page length by using the control panel. When the printer is on line, press the LOAD/EJECT button once to select the 8.5-inch page length. The printer beeps four times to signal that the 8.5-inch length has been selected. If you press the LOAD/EJECT button again, the printer beeps three times and returns to the page length selected by DIP switch

2-1.

3-10 Using the Printer

-

-

-

Skip Over Perforation

By changing the setting of DIP switch 2-3, you can set skip over perforation to on or off. If this feature is on when using continuous paper, a one-inch margin is provided between the last printable line on one page and the first printable line on the next page. This feature is very convenient if your application program does not provide for top and bottom margins.

If you adjust your loading position correctly, you can get half of the margin at the bottom of one page and half at the top of the next page, as shown in the following illustration.

DIP switch 2-3 ON (Skip over perforation ON)

-

-

Note:

Most application programs take care of top and bottom margins. Use skip over perforation only if your program does not provide these margins.

The skip over perforation setting can be set to values other than one inch by using

the

ESC N command. See the Command Summary in

Chapter 9 for details.,

Using the Printer 3-11

Adjusting the Loading Position

The Loading Position

The loading position is the position of the paper when it has been loaded automatically by the printer.

This position is important because it determines where the printing begins on the page. If the printing is too high or too low on the page, change the loading position using the micro-adjustment feature described in the next section.

CAUTION:

Never use the platen knob to feed paper except in case of a paper jam or other paper feeding problem. (If you need to use the platen knob, make sure the power is off .) If you need to adjust the loading position, always use the micro-adjustment feature.

Until the loading position is reset, the printer remembers this position even if it is turned off, and uses it as a reference point for feeding paper.

The micro-adjustment feature moves the paper in 1/180-inch increments to make fine adjustments to the loading position. Once you have used micro-adjustment to change the loading position of continuous paper, the printer remembers that position even after it is turned off.

When you use micro-adjustment to change the loading position of single-sheet paper, however, the printer does not remember this position after the power is turned off. When the power is turned back on, the loading position returns to its factory setting.

3-12

Using the Printer

Adjusting the Load Position

Using Micro-adjustment

1. Make sure that the printer is turned on and that either a single sheet or continuous paper is ready to be loaded.

2. Press the LOAD/EJECT

button to feed paper to the loading position.

Then press the ON LINE button; the MULTI-PART light begins to blink.

MULTI -

PART

Note:

You

can use the FORM FEED and LINE FEED buttons for micro-adjustment only while the MULTI-PART light is blinking.

Using the Printer

3-13

Adjusting the Loading Position

3. Press the FORM FEED button to feed the paper forward or the LINE

FEED

button to feed the paper backward.

Note: When the Paper

reaches the factory-set loading position, the printer beeps and micro-adjustment feeding pauses for a moment before continuing. You can use this factory setting as a reference point when adjusting the printer’s loading position.

When the paper reaches either the minimum or maximum top

margin, the printer beeps and the paper stops moving.

3-14

Using the Printer

Using Short Tear-Off

When you are finished printing, the short tear-off feature automatically feeds the perforation of the continuous paper to the tear-off edge of the printer cover so that you can tear off the last sheet. When you resume printing, the paper feeds backward to the loading position. This feature lets you save the paper normally lost between documents.

To use this feature, set DIP switch 2-2 to on, and make sure that the length of the continuous paper matches the length set by DIP switch

2-1. Then load continuous paper in the normal way.

CAUTION: To change the setting of a DIP switch, first turn off the printer, change the DIP switch setting, and then turn the printer back on.

You can leave the short tear-off feature turned on (DIP switch 2-2 on) even when you are using single sheets. When you move the paper release lever to the single-sheet position, the short tear-off feature is

disabled.

WARNING:

Never use short tear-off with

labels.

Otherwise, labels may come off their

backing and

jam the printer.

When you have finished printing, if the perforation is at the top of form position, the printer automatically feeds the perforation of the continuous paper to the tear-off edge of the printer cover. You can then tear off the page using the tear-off edge as shown on the next

page.

Using the Printer 3-15

If the page perforation is not properly aligned with the tear-off edge, you can adjust the tear-off position using micro-adjustment, as described below.

Note:

Short tear-off is performed whenever the printer receives a full page of data or a form feed, and no more data is received for three seconds

When you resume printing after tearing off the sheet, the paper automatically feeds backward to the loading position before printing begins.

Adjusting the Tear-off Position

If the paper’s perforation does not meet the tear-off edge, you can adjust the tear-off position using the micro-adjustment feature.

3-16 Using the Printer

1. Make sure the printer feeds the paper to the tear-off position after printing the document.

2.

The MULTI-PART light should begin blinking, indicating that you can now use the micro-adjustment feature to make fine adjustments to the tear-off position.

Using the Printer 3-17

Using Short Tear-Off

3.

To make fine adjustments to the tear-off position, press the FORM

FEED

button to feed the paper forward or the LINE FEED button to feed it backward.

You can now tear off your document from the perforation and resume printing. The printer remembers this new tear-off position even after the printer is turned off and on again.

3-18

Using the Printer

Selecting Typestyles

You can produce a wide range of typestyles by selecting different character fonts, widths, and other enhancements from the SelecType control panel or by using software commands. This section describes only the features controlled by SelecType. To use software commands, see the Command Summary in Chapter 9.

You can use the SelecType section of the control panel to choose fonts and condensed printing. Orange lights indicate which features you have chosen. For example, if both indicator lights are lit, the slot is selected for your optional font cartridge (if one is installed).

Using the Printer

3-19

Note: The settings you select using the SelecType panel remain valid until the printer is turned off or until it receives other instructions from software. Some application programs, however, are designed to control all typestyle functions. These programs cancel all previous typestyle settings by sending certain software commands before printing. Because these commands override SelecType settings, you should use the program’s print options instead of SelecType to select your typestyles. If SelecType does not work with a particular application, check your software manual for instructions on selecting typestyles.

Character Fonts

The LQ-1010 printer has three built-in fonts:

DRAFT

SANS SERIF

3-20

Using the Printer

The DRAFT mode uses fewer dots per character for high-speed printing, which makes it ideal for rough drafts and editing work.

ROMAN

and SANS SERIF are Letter Quality (LQ) fonts. Letter Quality takes a little longer to print, but produces nicely formed characters suitable for most documentation requirements.

Other fonts are available on optional font cartridges. See Multi-Font

Module in Chapter 5.

Condensed Mode

You can use the condensed mode to change the size of printed characters. In the condensed mode, characters are approximately 60 percent of the width of normal characters. Hence, condensed printing is very useful for spreadsheets and other applications where you need to print the maximum amount of information on a page. You can combine

the

condensed mode with 10 and 12 cpi printing, but not 15 cpi.

To select the condensed mode, simply press the CONDENSED button so that the orange indicator light comes on. To turn off the condensed mode, press the button again.

The following printout compares normal 10 and 12 cpi with condensed

10

and 12 cpi. The condensed

10

cpi is 17 cpi, and the condensed 12 cpi is 20 cpi.

T h i s i s 1 0 C P I p r i n t i n g .

This

is

condensed

10

CPI

printing,

This is 12 CPI printing.

This is

condensed 12 CPI

printing.

Using the Printer

3-21

Selecting an International Character Set

International character sets provide you with the characters and symbols used in other languages. You can select one of eight international character sets by changing the DIP switch settings.

Whenever the printer is turned on, reset, or initialized, the character set selected by the DIP switches becomes the default character set.

To select an international character set, set DIP switches 1-1, 1-2 and

1-3 according to the table below.

This table also shows the characters that differ in each international character set.

-

-

CAUTION:

To change the setting of a DIP

switch, first turn

off the printer, change the DIP switch

setting, and then turn the printer

back on.

3-22 Using the Printer

Selecting an International Character Set

In addition to the eight character sets shown on the previous page, the seven international character sets that follow can be selected with a software command: ESC R. For more information, see the Command

Summary in Chapter 9.

Country

8 Japan

9 Norway

10 Denmark II

11 Spain II

12 Latin America

13 Korea

64 Legal

ASCII code hex

23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E

Using the Printer

3-23

Choosing a Character Table

DIP switch 1-7 selects either the italic character table or the Epson

Extended Graphics character table. The Epson Extended Graphics character table contains international accented characters, Greek characters, mathematic symbols, and character graphics for printing lines, comers, and shaded areas.

If you have an IBM

® or IBM-compatible computer, select the Epson

Extended Graphics table when you wish to print character graphics as they are displayed on the screen. Even if you select Epson Character

Graphics, you can still print ordinary text and italics. For italics, see the description of the ESC

Chapter 9.

4

command in the Command Summary,

Note: In most cases, Epson Extended Graphics is the preferred selection.

Sample printouts of the italic characters and the Epson Extended

Graphics characters are shown below.

Italics

Epson Extended Graphics

3-24

Using the Printer

Choosing a Character Table

To select a character table, set DIP switch 1-7 according to the table below.

Character table

Italics

Graphics

DIP SW 1-7

OFF

ON

CAUTION:

To change the setting of a DIP switch, first turn

off the printer, change the DIP switch, and then turn the printer back on.

Tables showing which characters are printed in each of the character tables are listed in the Appendix.

Using the Printer

3-25

Using the Data Dump Mode

The data dump mode is a special feature that makes it easy for experienced users to identify the cause of communication problems between the printer and application programs. The data dump mode gives a printout of the codes reaching the printer.

To use the data dump mode, follow these steps:

1. Make sure that the printer is loaded with either single-sheet or continuous paper.

3-26 Using the Printer

Using the Data Dump Mode

2. If

the printer is on, switch it off, then hold down the FORM FEED and LINE FEED buttons at the same time you turn on the printer.

3.

Run any program that causes the printer to print (either an application program or one in any programming language). Your printer prints out all the codes sent to the printer, as shown below.

(In order to print the last line, you will have to take the printer off line.)

. @ . R . . t . . 6 . . P . D .

T h i s i s a n e x a m p l e o f a d a t a d u m p p r i n t o u t . T h i s f e a t u r e m a k e s

i t e a s y t o

On the left side of the printout all the codes are printed in hexadecimal format. On the right side of the printout all printable characters are printed, and others, such as control codes, are represented by dots.

Using the Printer 3-27

Using the Data Dump Mode

4. To turn off the data dump mode after you have taken the printer off line, turn off the printer.

By comparing the characters printed in the text field on the right side of the data dump printout (see step 3) with the printout of hex codes, you can check which codes are being sent to the printer.

To interpret the data dump printout, examine the first three hex codes on the second line of the printout sample (20 20 54). Each hex code 20 represents a space; hex code 54 represents the letter T. Check the second line of the text field on the right side of the printout and you will find the letter T preceded by two spaces.

The chart below interprets the first eight codes.

Hex codes

1B 40

1B 52 00

1B 74 01

Command

ESC

ESC R 0

ESC t 1

Function

Initialize printer

Select USA character set

Select Epson Extended Graphics set

3-28 Using the Printer

Chapter 4

Software and Graphics

Enhancing Your Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-2

Character Spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-2

Character Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-3

Special Effects and Emphasis . . . . . . . . . . . . . . . . . . . . . . . . .

4-4

Selecting Typestyles With Master Select . . . . . . . . . . . . . . .

4-6

Graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

The Print Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

The Graphics Command . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Column Reservation Numbers . . . . . . . . . . . . . . . . . . . . . . 4-14

A Simple Graphics Program . . . . . . . . . . . . . . . . . . . . . . . . 4-14

Designing Your Own Graphics . . . . . . . . . . . . . . . . . . . . . . 4-15

User-defined Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-20

Designing Your Characters . . . . . . . . . . . . . . . . . . . . . . . . . .

4-20

Defining Your Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-22

Sending Information to Your Printer . . . . . . . . . . . . . . . . . . .

4-24

Printing User-defined Characters . . . . . . . . . . . . . . . . . . . . . .

4-27

Copying ROM Characters to RAM . . . . . . . . . . . . . . . . . . .

4-28

Letter Quality Characters . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-29

Superscripts and Subscripts . . . . . . . . . . . . . . . . . . . . . . . . . .

4-29

Mixing Print Styles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-30

Software and Graphics

4-1

Enhancing Your Printing

You can obtain a wide variety of printing effects with the LQ-1010, from changing the number of characters per inch to using special effects on selected words and phrases. This section gives you a sampling of the features you may select with your software.

For software control of these features, see the instructions for your application programs or look up their specific commands in the

Command Summary in Chapter 9.

Character Spacing

To add greater variety to your documents, the LQ-1010 has three cpi spacings, as well as proportional spacing. Each one can be selected with a software command.

For each of the three built-in fonts, you can choose a character spacing of 10, 12, or 15 characters per inch, or proportional spacing. The printout below compares the three cpi spacings:

T h i s i s 1 0 c p i p r i n t i n g .

This is 12 cpi printing.

This is 15 cpi printing

As shown above, 15 cpi characters are only about two-thirds the height of 10 and 12 cpi characters. This makes 15 cpi particularly useful when you want to separate certain material from the main text.

In fixed cpi spacing each character is given the same amount of space.

The width of proportional characters, however, varies from character to character. For example, a narrow letter like i takes less space than a wide letter like W. The width of each proportional character is given in the Appendix.

4-2 Software and Graphics

Enhancing Your Printing

The following printout compares 10 cpi spacing with proportional spacing:

This is 10 cpi printing.

This is proportional printing.

Note: Proportional spacing is not available in the draft mode.

Character Size

In addition to the basic cpi spacings and proportional spacing, the

LQ-1010 offers three other modes that can change the size of your printing. These modes are double-wide, double-high, and condensed.

The double-wide mode doubles the width of any size character, while the double-high mode doubles the height of any size character. These modes are useful for emphasizing document titles and headings in reports, but are usually not suitable for large amounts of text. These modes can also be combined to obtain even more impressive printing results.

T h i s i s n o r m a l 1 0 c p i p r i n t i n g .

T h i s i s d o u b l e - w i d e .

This is double-high,

This is double-wide and d o u b l e - h i g h .

Software and Graphics

4-3

Enhancing Your Printing

Both 10 and 12 cpi printing can be reduced to about 60 percent of their normal width using the condensed mode. This mode is particularly useful for printing wide spreadsheets because condensed 12 cpi printing allows you to print up to 272 characters on a 13.6-inch line.

The condensed mode can be selected with a software command, or by using SelecType (see Chapter 3). Even if you turn the condensed mode

on

with SelecType, you can still turn it off with a software command.

Condensed 10 cpi gives you many characters on a line,

Condensed 12 cpi gives you even more characters on a line,

Widening or narrowing the characters also widens or narrows the spaces between words. Because word processors usually create a left margin by printing spaces, you may need to change the left margin and the number of characters on a line to keep change character widths.

the

margins correct if you

Special Effects and Emphasis

The LQ-1010 offers two ways of emphasizing text and also allows you to use underlining, superscripts, subscripts, and italics. These features can be controlled directly by software commands. Many application programs can also produce some of program manual for details.

these

effects. See your application

Emphasized and double-strike printing

Emphasized and double-strike printing can give words and phrases added prominence. In emphasized mode, each character is printed twice as the print head moves across the paper, with darker, more fully formed characters.

the dots in the second

pass printed slightly to the right of the first pass. This process produces

4-4

Software and Graphics

Enhancing Your Printing

In double-strike mode, the print head prints each line twice, making the text bolder. For even greater boldness, emphasized and double- strike can be combined. The following samples show the different effects you can achieve using these modes alone and in combination.

This is

R O M A N

p r i n t i n g .

This is ROMAN, emphasized.

This is ROMAN, double-strike.

T h i s i s R O M A N , w i t h b o t h .

Italic printing

You can print italics by using the ESC 4 software command. This is true no matter how DIP switch 1-7 is set.

T h i s i s R O M A N p r i n t i n g .

T h i s i s

R O M A N

i t a l i c s ,

Underlining, strike-through, and overlining

The underline, strike-through, and overline modes are useful for highlighting selected text. This feature can be used to score spaces, subscripts, and superscripts without a break. You can choose from a variety of line styles, including single, double, broken, or continuous.

See the ESC ( - command in Chapter 9 for more information.

T h i s i s c o n t i n u o u s u n d e r l i n i n g .

T h i s i s b r o k e n o v e r l i n i n g .

Software and Graphics 4-5

Enhancing Your Printing

Superscripts and subscripts

Superscripts and subscripts can be used for printing footnote numbers and mathematical formulas. The example below shows underlining and subscripts combined in a mathematical formula.

average

= (a1 + a1

+ a2

+

. . . . . . . .

+ a n

1 n

Outline and shadow

The

outline and shadow features are useful for adding variation and emphasis to text that you wish to stand out, such as headings. The following samples show the outline and shadow features individually, plus a combination of outline with shadow.

Selecting Typestyles With Master Select

Your LQ-1010 printer has a special ESCape code called Master Select that allows you to choose many combinations of these nine modes: 10 cpi, 12 cpi, proportional spacing, condensed, emphasized, double-strike, double-wide, italics, and underline. For more information on sending ESCape codes to your printer, see Chapter 9.

The format of the Master Select code is shown below:

ASCII:

Decimal:

Hexadecimal:

ESC !

27 33 n

1B 21 n

n

4-6 Software and Graphics

Enhancing Your Printing

The variable n is a number that identifies the mode or combination of modes. To find the value of n use the following table to add up either the decimal or hexadecimal numbers for the features you want.

Feature

10 cpi

12 cpi proportional condensed emphasized double-strike

double-wide italics underline

Dec.

Hex.

0

00

1 01

2 02

4 04

8 08

16 10

32 20

64 40

128 80

For example, to print a title you may want to use double-wide characters printed in the double-strike mode. You would add three numbers together to calculate the value of n.

12

cpi

12 cpi 1

Double-strike

16

Double-wide 32

n = 49

After calculating the value of n, you use the Master Select command to send the value to the printer.

ASCII:

Decimal:

Hexadecimal:

ESC !

1

27 33 49

1B 21 31

Software and Graphics

4-7

Enhancing Your Printing

The print quality and font must be set separately, using SelecType or the ESC x and ESC k commands. There are two more things to consider when using the Master Select command: l l

Master Select cancels any of the other listed features that you do not set. For example, if you have already set a different character width and you use Master Select to set emphasized double-strike, the character width is reset to

10

cpi.

Proportional spacing overrides

10, 12,

and

15

cpi.

4-8 Software and Graphics

Graphics

The dot graphics mode allows your printer to produce pictures, graphs, charts, or almost any other pictorial image you can create.

Because many commercial software programs use graphics, you may be able to print pictures and graphs like the ones on this page and the next by simply giving your software a few instructions.

The quickest and easiest way to print graphics on your printer is to use a commercial graphics program. With such programs you usually create an image on your monitor then give a command to send the image to the printer.

If you use commercial software that produces graphics, all you need to know about dot graphics is how to use the software. The application program will take care of the printer. (Some programs call this bit

image

printing.) On the other hand, if you wish to do your own programming or merely wish to understand how this printer prints graphics, read on.

Software and Graphics

4-9

Graphics

Income Breakdown

The Print Head

To understand dot graphics you need to know a little about how your printer’s print head works.

The print head has 24 pins. As the print head moves across the page, electrical impulses cause the pins to fire. Each time a pin fires, it strikes the inked ribbon and presses it against the paper producing a small dot.

As the print head moves along, the pins fire time after time in different patterns forming letters, numbers, and symbols.

Because the dots overlap each other both horizontally and vertically in

Letter Quality mode, it is difficult to see the individual dots. Instead, the letters and symbols seem to be made up of unbroken lines.

In order for the dots to overlap vertically, the pins in the print head are in more than one column, but the intelligence of the printer handles the timing of pin firings so that the effect is that of 24 pins arranged in a single vertical column.

Dot

patterns

The print head is able to print graphics as well as text because graphic images are formed by the printer in about the same way that pictures in newspapers and magazines are printed. If you look closely at a

4-10 Software and Graphics

Graphics

newspaper photograph, you will find that it is made up of thousands of small dots. Your printer also forms its images with patterns of dots, as many as 360 dots per inch horizontally and 360 dots per inch vertically.

The images printed by this printer can, therefore, be as finely detailed as the ones at the beginning of this section.

Twenty-four-pin graphics

The graphics mode that takes full advantage of this printer’s print head is 24-pin graphics. This mode has five densities, but for simplicity this explanation deals with only one of them, triple-density.

Triple-density prints up to 180 dots per inch horizontally. As the print head moves across the paper, every 1/180th of an inch it must receive instructions about which of its 24 pins to fire. At each position it can fire any number of pins, from none to 24. This means that the printer must receive 24 bits of information for each column it prints. Since the printer uses 8-bit bytes of information in communicating with the computer, it needs three bytes of information for each position.

Pin labels

To tell the printer which pins to fire in each column, you first divide each of the vertical columns into three sections of eight pins each and consider each section separately. Since there are 256 possible combinations of the eight pins in each section, you need a numbering system that allows you to use a single number to specify which of the

256 possible patterns you want. This numbering system is shown

below

:

Software and Graphics 4-11

Graphics

To fire any one pin, you send its number to the printer. To fire more than one pin at the same time, add up the numbers of the pins and send the total. Using these labels for the pins, you fire the top pin by sending

128.

To fire the bottom pin, you send

1.

If you want to fire only the top and bottom pins, you simply add 128 and

1,

and send

129.

By adding the appropriate label numbers together, you can fire any combination of pins. Below are three examples of how to calculate the number that will fire a particular pattern of pins.

With this numbering system, any combination of the eight pins adds up to a decimal number between

0

and duplicated.

255,

and no numbers are

Since there are 24 pins in each column, you must make a calculation for each of the three sections in each column. As you can see, this method of planning and printing dot graphics requires considerable calculation.

Because triple-density uses

180

columns per inch, printing a single line of triple-density graphics only one inch long requires 540 numbers.

Fortunately, commercial graphics software is available to do these calculations for you.

Before you can put these numbers into a graphics program, however, you need to know the format of the graphics command.

4-12 Software and Graphics

Graphics

The Graphics Command

The graphics mode command is quite different from the other commands used by the printer. For most of the other printer modes, such as emphasized and double-wide, one ESC code turns the mode on and another turns it off. For graphics, the command is more complicated because the code that turns on a graphics mode also specifies how many columns it will use. After the printer receives this code, it interprets the numbers that follow as pin patterns and prints them on the paper.

Your printer has one command that allows you to use any of the

11 graphics options. The format of the command is:

ESC * m nl n2 data

In this command, m selects the graphics option and n1 and n2 specify the number of columns to reserve for graphics. The available graphics options are listed below:

* Adjacent dots cannot be printed in this mode.

Software and Graphics

4-13

Graphics

Column Reservation Numbers

The graphics command requires more than one number to specify how

many

columns to reserve because one line can use thousands of columns, but the printer does not use numbers larger than 255 in decimal. Therefore the graphics mode command uses two numbers, n1 and n2, for reserving columns.

To find nl and n2, divide the total number of columns by 256. The result is n2; the remainder is nl. Since the command is set up for two numbers, you must supply two even if you need only one. When you need fewer than 256 columns, just make nl the number of columns you are reserving and make n2 a zero.

For example, if you wish to send 1632 columns of graphics data, nl should be 96 and n2 should be 6 because 1632 = 96 + (6 x 256).

The printer interprets the number of bytes specified by nl and n2 as graphics data, no matter what codes they are. This means that you must be sure to supply enough bytes of graphics data or the printer will stop and wait for more data and will seem to be locked. If, on the other hand, you supply too much graphics data, the excess will be interpreted and printed as regular text.

A Simple Graphics Program

This first program is just a simple example to show you how the graphics command, column reservation numbers, and data can be used in a BASIC program.

4-14

Software and Graphics

Graphics

Type in and run the following program. Be especially careful to include both semicolons. The program produces the printout you see below:

10 WIDTH "LPT1:",

255

20 LPRINT CHR$(27)"*"CHR$(32)CHR$(40)CHR$(0);

30 FOR X=1 TO 120

40 LPRINT CHR$(170);

50 NEXT X

Line 20 selects single-density 24-pin graphics mode (mode 32) and also reserves 40 columns for graphics. Since 24-pin graphics requires three bytes of data for each column, line 30 begins a loop to supply 120 bytes of data. Line 40 contains the number 170, which produces the first pin pattern shown in the section on pin labels, and line 50 ends the loop.

Designing Your Own Graphics

With what you know now, you can use the simplest application of graphics-calculating by hand the data to print the graphic image.

While this method is the most tedious, it helps you understand dot graphics. It is also useful for small graphic elements that are used many times.

Software and Graphics

4-15

Graphics

The illustration below shows how you can use a grid on paper to plan where you want dots to be printed. This grid is for a single line of graphics 42 columns long. Since each line of 24-pin graphics is approximately 1/8th of an inch high and since triple-density graphics prints 180 dots per inch horizontally, a design planned on this grid will be about 1/8th of an inch high and less than 1/4th of an inch wide.

The actual pattern that the printer prints on the paper is, of course, made up of dots that overlap each other both vertically and horizontally. The reason the planning grid uses an x for each dot is that using an accurate representation of the dots makes calculating the data numbers difficult because they cover each other. Therefore, remember that each x represents the center of a dot, and the dots actually overlap.

Write the assigned values of the pins next to your design, then total the values for each column of dots. These totals are the values that you send to the printer as graphics data to print the design.

4-16

Software and Graphics

Graphics

Below is the same grid divided into three sections to make the data calculation easier. At the bottom of each section of each column is the total of the pin numbers for that section. This gives you the total of 126 data numbers necessary to print this small figure.

Software and Graphics

4 1 7

Graphics

Below is the BASIC program that prints the design shown on the previous pages. Note that the data numbers in lines 80 through

140 are the same numbers that are at the bottom of each section in the last illustration. The WIDTH statement in line

10

is for IBM PC BASIC; the

WIDTH statement format may be different for your system.

10

20

WIDTH

"LPT1:",255

LPRINT

CHR$;(27)"*"CHR$(39)CHR$(42)CHR$(0);

30

40

50

FOR X=1 TO 126

READ N

LPRINT CHR$(N);

NEXT X

60

70

80

LPRINT

DATA 0,0,63,0,0,127,0,0,255,0,3,255,0,15,255,0,31,255

90

DATA 0,127,255,0,255,255,1,255,3,255,255,7,255,255,l5,

255, 255

100 DATA

31,255,254,31,255,252,31,255,255,248,31,255,240,31,255,

224,31,255,192

110 DATA

31,255,0,31,252,0,31,240,0,31,224,0,31,128,0,31,240,0

120 DATA

31,255,192,28,255,224,28,l27,240,28,l5,248,30,0,252,

31,0,126

130 DATA

15,128,15,7,192,7,3,240,7,1,254,7,0,255,7,0,127,135

140 DATA 0,31,199,0,7,231,0,1,247,0,0,255,0,0,127,0,0,63

In this program, line 20 assigns the graphics option (24pin triple-density) with code 39. Code

42 sets the number of pin columns at

42.

Lines 80 through

140 contain you see below:

126

bytes of data (42-pin columns x 3 bytes) for each pin column. Lines

30 through

60 print the design that

4-18

Software and Graphics

Graphics

Notice that the dots overlap quite a bit. This design was printed using the triple-density, 24-pin graphics option because the density is the same

(180 dots per inch) in both directions (horizontal and vertical).

Adding the following lines to the preceding program causes the pattern to print 10 times in a row as shown below:

15 FOR C-1 TO 10:RESTORE

65 NEXT C

Software and Graphics

4-19

User-defined Characters

With this printer, it is possible to define and print characters of your own design. You can design an entirely new alphabet or typeface, create special characters for use as mathematical or scientific symbols, or create graphic patterns with user-defined characters to serve as

building blocks for larger designs.

Below, you can see samples of typefaces created with the user-defined character function.

Note: To use user-defined characters, you must turn DIP switch 2-5 off.

You can make the task of defining characters easier by using a commercial software program that assists you in creating characters or simply supplies you with sets of characters already created. Also, some popular software programs make use of the printer’s user-defined character function to enhance printouts. (These characters are called download characters in some programs.)

The standard ASCII characters are stored in the printer’s Read Only

Memory (ROM) or optional Multi-Font Module, and the user-defined characters are stored in the printer’s Random Access Memory (RAM).

Designing Your Characters

User-defined characters are like dot graphics because you send the printer precise instructions on where you want each dot printed. In fact, planning a user-defined character is like planning a small dot

graphics pattern.

4-20

Software and Graphics

User-defined Characters

Design grids

To design a character you use a grid that is 24 dots high-one dot for each pin on the printer’s print head. The width of the character matrix depends on the character set in use. For draft characters, the grid is nine dots wide, for Letter Quality it is 29 dots wide, and for proportional characters it is 37 dots wide. The dots for both Letter Quality and proportional characters are spaced more closely together than those for draft characters.

The illustrations below show the two design grids. The line at the side, labeled cap, indicates the top of a standard capital letter. The line labeled base indicates the baseline for all letters except those with descenders (the bottom parts of such letters as j and y). The bottom row is usually left blank because it is needed for underlining.

The grid on the right side can be used for either Letter Quality or proportional characters. For Letter Quality you do not use all the columns.

Draft pica Letter quality / Proportional

Software and Graphics

4-21

User-defined Characters

There is one restriction in designing characters. Dots in the same row may not print in adjacent columns. This means that there must be an empty dot position both to the left and right of each dot that prints.

This is true in draft, Letter Quality, and proportional mode.

Defining Your Characters

The first step in defining characters is to place the dots on a grid just as you want them to print. The examples shown here, like the ones in the graphics section, use an x to represent each dot.

In the illustration below, you see a draft grid with a simple userdefined character planned on it.

Now you translate the dot pattern you’ve created on paper to a numeric format so you can send the data to your printer. Every dot has an assigned value. Each vertical column (which has a maximum of 24 dots) is first divided into three groups of eight dots. Each group of eight dots is represented by one byte, which consists of eight bits. Hence, one bit represents one dot.

4-22

Software and Graphics

User-defined Characters

Data numbers

The bits within each byte have values of

1, 2, 4, 8, 16, 32, 64,

128)

is at the top of the column and the

1)

is at the bottom.

and

128.

In the vertical column of dots, the bits are arranged so that the most significant bit (with a value of least significant bit (with a value of

The next illustration shows how to use this method to calculate the data numbers for the character in this example. On the left side of the figure, the data numbers are calculated for the middle column. The value of each byte is calculated by adding the values of the rows in which dots appear. The right side of the figure shows the whole character with the three data numbers for each column indicated at the bottom.

This manual uses decimal numbers because the program examples are written in BASIC and everyone is familiar with decimals. The data you send to your printer, however, must be in the form (binary, decimal, or hexadecimal) that you can use with your programming language.

Software and Graphics

4-23

User-defined Characters

You have seen how to design a character by placing dots on a grid and translating the dots to decimal equivalents. The last step in defining a character is sending this information to your printer.

Sending Information to Your Printer

The printer loads characters in the print style (Letter Quality, draft, or proportional) that the printer is currently using. It also records whether italic, superscript, or subscript is turned on. This means that if you want to print a character in italics, for example, you must have the italic mode turned on when you define the character.

The command your printer uses to define characters is one of the most complex in its repertoire. The format of the command is this:

ESC & 0 nl n2 d0 dl d2 data

The ESC & is simple enough. The 0 (which is ASCII code 0, not the character zero in quotation marks) allows for future enhancements. At this time, it is always ASCII 0.

You can define many characters with a single command. The values nl and n2 are the ASCII codes of the first and last characters you are defining. If you are defining only one character, nl and n2 are the same. You can use any codes between decimal 32 and

127 for nl and

n2, but it is best not to define decimal 32, which is the code for a space.

Also, you can use letters in quotation marks instead of ASCII codes for

n1 and n2.

Note: Because user-defined characters require additional memory, you must set DIP switch 2-5 to 1 KB (off) before downloading these characters.

4-24

Software and Graphics

User-defined Characters

An example will show how to specify nl and n2. For instance, if you wanted to redefine the characters A through Z, nl would be A (or

ASCII code 65) and n2 would be Z (or ASCII code 90). So the command ESC & 0 AZ (followed by the appropriate data) would replace the entire alphabet of capital letters.

Following the specification of the range of characters to be defined in this command are three data bytes, d0, dl, and d2, that specify the width of the character and the space around it. The left space (in dot columns) is specified by d0, and the right space is specified by d2. The second byte, dl, specifies the number of columns of dots that are printed to make up the character. By varying the width of the character and the spaces around it, you can create proportional-width characters that print at draft speed. The table below shows the maximum values for these bytes.

Mode

Draft

Letter Quality 10 cpi

Letter Quality 12 cpi

Proportional

d1

9

29

23

37

d0 + dl + d2

12

36

30

42

The last part of the command to define your characters is the actual data that defines the dot patterns for each character. Since it takes three bytes to specify all the dots in one vertical column, your printer expects

dl x 3 bytes of data to follow d2.

Software and Graphics

4-25

User-defined

Characters

This example of a character definition program should make this clear:

10 LPRINT CHR$(27)"x0"

20 LPRINT CHR$(27)"&"CHR$(0);

30

LPRINT '@@";

40 LPRINT CHR$(l)CHR$(9)CHR$(l);

50 FOR I=1 TO 27

60 READ-A: LPRINT CHR$(A);

70

NEXT I

80 LPRINT "@@@@@"

90 LPRINT CHR$(27)"%"CHR$(1);

100 LPRINT "@@@@@"

110 LPRINT CHR$(27)"%"CHR$(0);

120 LPRINT "@@@@@"

130

END

140 DATA

1,0,0,2,0,0,4,0,0

150 DATA

8,0,0,23,255,240,8,0,0

160 DATA

4,0,0,2,0,0,1,0,0

In line

10, the

ESC x0 command selects draft printing.

The actual character definition starts in line 20. The two @ signs in line

30 represent n1 and n2, the range of characters being defined (in this case, a range of

1).

Line

40 contains d0, d1, and d2.

The information about the actual character design (which is contained in the DATA statements at the end of the program) is sent to the printer in the loop between lines

50 and

70.

Note: When defining Letter Quality or proportional characters, put a WIDTH statement in your program to prevent carriage return and line feed codes from interfering with your definitions.

4-26 Software and Graphics

User-defined Characters

Printing User-defined Characters

If you entered the previous program example, you defined an arrow and placed it in the RAM location for ASCII code 64 (replacing the @ sign). You can now print out a three-line sample of your work. The first and third lines (printed by lines 80 and 120) print the normal @ sign.

The second line (printed by line 100) prints out the arrow that you defined.

Run the program to see the printout below:

As you can see, both sets of characters (the @ from the original characters in ROM that the printer normally uses and the alternative character you defined) remain in the printer available for your use. The command to switch between the two sets is used in line 90 and 110. It is:

ESC % n

If n is equal to 0, the normal ROM character set is selected (this is the default). If n is equal to 1, the user-defined character set is selected. If you select the user-defined character set before you have defined any characters, the command is ignored and the ROM characters remain in use.

You may switch between character sets at any time-even in the middle of a line. To try this, place semicolons at the end of lines 80 and 100 in

the

program example.

Software and Graphics

4-27

User-defined Characters

Copying ROM Characters to RAM

After running the program, if you select the user-defined character set and try to print other characters, the only one that will print is your arrow. Since no other characters are in the printer’s user-defined RAM, there is nothing else to print. Other characters sent to the printer do not even print as spaces; it’s as if they were not sent at all.

In many cases, you will want to redefine only a few of the characters to suit your needs-the rest of the alphabet will work fine as it is. As you have seen, it is possible to switch back and forth, at will, between the normal character set and your user-defined character set. It is, however, rather inconvenient.

Therefore, your printer has a command that allows you to copy all of the standard characters from ROM to the user-defined character set.

The command format is as follows, where the value of n represents the font family:

ESC : 0 n 0

Note: This command cancels any user-defined characters you have already created. You must send this command to the printer before you define characters.

If you use this command at the beginning of a program, then define your special characters and select the user-defined set, you can print with the user-defined set as your normal character set. You never need to switch back and forth between sets.

4-28 Software and Graphics

User-defined Characters

Letter Quality Characters

If you select Letter Quality printing with the ESC xl command, you can design user-defined characters using up to

29 columns of the Letter

Quality/Proportional grid. The dot columns are spaced closer together horizontally than draft dot columns (the horizontal dot spacing is

1/360th of an inch as opposed to 1/120th of an inch for draft characters).

Proportional mode characters

Selecting the proportional character mode yields user-defined characters of the highest resolution. Characters can be designed using all

37 columns of the Letter Quality/Proportional grid.

Remember that in Letter Quality and proportional modes, as in draft mode, you cannot place dots in adjacent columns. There must be an empty dot position both to the left and right of each dot that prints.

Superscripts and Subscripts

You can also create superscript and subscript user-defined characters.

Just as Letter Quality characters are defined when the Letter Quality mode is selected, superscript and subscript characters are created when either superscript or subscript is selected.

These characters can be used as either superscripts or subscripts. The characters are exactly the same; only their placement is different. The difference between these characters and regular characters is that superscript and subscript characters are smaller. They are a maximum of 16 dots high. Their maximum width in dot columns is shown in the table below:

Mode

Draft

Letter Quality

Proportional

d1

7

23

23

d0 + d1 + d2

12

36

42

Software and Graphics

4-29

User-defined Characters

Since superscript and subscript characters are smaller, when you define them you only need two bytes of data for each vertical row of dots.

Design grids for these characters are shown in the figure below:

Draft pica

Letter Quality and Proportional

Mixing Print Styles

Each of the three user-defined character modes (draft, Letter Quality, and proportional) can be used in combination with most of your printer’s various print styles. For instance, emphasized mode works with user-defined characters. The characters you design are enhanced to give this printing effect .

Mixing the three types of user-defined character sets is not possible. For example, if you select draft and define some characters, then select proportional and define some more, the first draft character definitions are deleted. Only one type of character definition may be stored in

RAM at any time.

4-30 Software and Graphics

User-defined Characters

If you define characters in one mode, then switch to another mode and select the user-defined character set, the command is ignored and nothing is printed. The user-defined character definitions, however, remain unaffected. If you switch back to the mode in which they were defined, you can then select and print them.

Keep in mind that user-defined characters are stored in RAM, which is not permanent memory. When the printer power is turned off or the printer is initialized with the INIT signal, the user-defined characters are lost. (Some computers do this each time BASIC is loaded.)

Software and Graphics 4-31

Chapter 5

Using the Printer Options

The Cut Sheet Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Paper Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

Testing the Printer in the Cut Sheet Feeder Mode . . . . . . . . 5-10

Single-sheet Insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13

Operating the Cut Sheet Feeder . . . . . . . . . . . . . . . . . . . . . . 5-15

Removing the Cut Sheet Feeder . . . . . . . . . . . . . . . . . . . . . 5-17

The Pull Tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21

Paper Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23

Removing the Pull Tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30

The Multi-Font Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-34

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-37

Selecting a Font . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-38

The Interface Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-40

Choosing an Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-40

Compatible Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-41

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-41

#8143 New Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . 5-49

Using the Printer Options

5-1

The Cut Sheet Feeder

The optional cut sheet feeder

(C806241)

makes it possible to handle single-sheet paper more easily and more efficiently. Up to

150

sheets

of standard bond paper can be fed automatically into the printer without reloading.

Installation

Note: Assemble the cut sheet feeder by following the instructions provided in its accompanying manual.

1.

Make sure that the printer is turned off. Then push the paper release lever all the way to the rear.

5-2 Using the Printer Options

2. Remove the paper guide and printer cover.

The Cut Sheet Feeder

3. Replace the clear plastic part of the printer cover with the clear plastic part included with the cut sheet feeder.

Using the Printer Options

5-3

The Cut Sheet Feeder

4.

Tilt the cut sheet feeder slightly forward to fit the notches at the

base

of the unit over the pins inside the printer. Tilt the feeder back until it rests on top of the printer.

5-4

Using the Printer Options

The Cut Sheet Feeder

5. Attach the printer cover as shown in the illustration below.

6. Turn on the cut sheet feeder mode by setting DIP switch 1-8 to on.

7. Turn on the printer,

Using the Printer Options

5-5

The Cut Sheet Feeder

Paper Handling

1. Make sure that the cut sheet feeder mode is turned on with DIP switch 1-8 and that the printer is turned on.

2. Pull the paper set levers all the way forward until the paper supports retract and lock open to allow for paper loading.

5-6

Using the Printer Options

The Cut Sheet Feeder

3.

Slide the left paper guide to where the fin on the edge guide aligns with the arrow on the panel.

4.

Slide the right paper guide so that it roughly matches the width of your paper.

Using the Printer Options

5-7

The Cut Sheet Feeder

5. Take a stack of paper and fan it as shown. This keeps the paper from sticking and ensures that only one sheet feeds at a time. Tap the side and bottom of the paper on a flat surface to even the stack.

Note: For best results, use typewriter quality paper. If you plan to use paper with a glossy or textured surface, test it before using it to print documents. Do not use multi-part forms,

carbon paper, envelopes, or labels in the cut sheet feeder.

5-8 Using the Printer Options

The Cut Sheet Feeder

6. Insert the stack of paper between the paper guides, aligning it with the left edge of the guide. Then adjust the right paper guide until the paper is held firmly, but not so tightly that it causes the paper to buckle. Make sure the paper can move up and down freely.

Using the Printer Options

5-9

The Cut Sheet Feeder

7.

Push the paper set levers back until they click into place and clamp the paper against the guide rollers.

Testing the Printer in the Cut Sheet Feeder Mode

When you perform the cut sheet feeder self test, the printer counts the number of lines on the page. As shown on the following page, the number of lines counted is printed out at the bottom of the first test page. This number is the default page-length setting. This setting, however, can be overridden by software commands.

Running the self test is the same as when the cut sheet feeder mode is off. The steps below are for a self test in draft mode.

WARNING: Run the self test using 14.3 inch wide (364mm) paper.

5-10 Using the Printer Options

The Cut Sheet Feeder

1.

Make sure that the printer is turned off and a stack of paper is in the bin. Check that the cut sheet feeder mode is selected and the paper release lever is pushed to the rear.

2.

While holding down the LINE FEED button, turn on the printer. (For

LQ mode, press the FORM FEED button instead of the LINE FEED

Using the Printer Options

5-11

The Cut Sheet Feeder

A part of the printout of the first sheet is shown below. The printout of the second sheet is similar to the original self test described in Chapter 1.

T h i s

i s

t h e f i r s t l i n e .

T h i s

is

l i n e X X .

3. The self test continues until the paper runs out or until you press the ON LINE button. To stop the test, press the ON LINE button.

Note: To

resume the test, press the ON LINE button once more.

5-12 Using the Printer Options

The Cut Sheet Feeder

4.

To end the self test when paper is loaded, press the LOAD/EJECT button to eject the paper. Then turn off the printer.

Single-sheet Insertion

Your cut sheet feeder also has a single-sheet loading feature. This feature is especially useful because it allows you to switch to a different type or size of paper (for one sheet only) without replacing the stack of paper in your cut sheet feeder.

1.

Press the ON LINE button to set the printer off line.

Using the Printer Options

5-13

The Cut Sheet Feeder

2.

Align the single sheet to be fed with the mark on the left paper guide; then slide the sheet into the printer path until you feel resistance.

5-14

Using the Printer Options

3. Press the LOAD/EJECT

button to load the sheet.

The Cut Sheet Feeder

Operating the Cut Sheet Feeder

After stacking paper in the cut sheet feeder, make sure the printer is turned on and that the ON LINE light is on. In the on line status, a new sheet of paper loads automatically whenever a printable character or line feed command is sent to the printer.

Paper out condition

When the printer is on line and receives print data from the computer, the first sheet loads automatically. Subsequent sheets load automatically as necessary.

l

In the cut sheet feeder mode, the PAPER OUT light goes on while a sheet of paper is being fed, but the printer remains on line.

l

When the specified paper bin is empty, the printer automatically goes off line, the PAPER OUT light goes on, and the beeper sounds.

To resume printing, add more paper and press the ON LINE button.

Using the Printer Options

5-15

The Cut Sheet Feeder

Note:

If you turn off your printer during the time the printer detects a paper out or paper jam condition, any data remaining in the printer’s buffer is discarded.

Control

panel operation

To operate the cut sheet feeder manually from the control panel when the printer is in the cut sheet feeder mode, first make sure that the printer is off line.

LINE FEED

When there is paper in the printer, press this button to feed the paper one line or hold it down to feed the paper continuously.

FORM FEED

LOAD/ EJECT

When there is no paper in the printer, press this button to load the paper. When there is paper in the printer, press this button to eject the sheet.

When there is no paper in the printer, press this button to load the paper. When there is paper in the printer, press this button to eject the sheet.

Software operation

The following commands cause the printer to eject the sheet in the printer without loading the next sheet.

FF: Form Feed

ESC EM R: Ejects a sheet in the cut sheet feeder mode

Note:

The ESC EM command is a software command used to control the operation of the cut sheet feeder. For more information about this command, see the Command Summary in Chapter 9.

5-16

Using the Printer Options

The Cut Sheet Feeder

If the paper reaches the bottom of the print area when any of the following line feed commands is used, the sheet in the printer is automatically ejected and the next sheet is loaded.

LF:

VT:

Line Feed; advances the paper one line

Vertical Tab; advances the paper to the next vertical tab position

Line feed; advances the paper n/180th of an inch ESC J:

Software is not effective while the printer is off line. Make sure that the printer is on line if you wish to control the cut sheet feeder using software commands.

Removing the Cut Sheet Feeder

1. Turn off the printer and remove any paper remaining in the bin and printer.

Using the Printer Options

5-17

The Cut Sheet Feeder

2. Remove

the

printer cover.

5-18

Using the Printer Options

The Cut Sheet Feeder

3. Tilt the cut sheet feeder back. Release its notches from the printer’s pins, and then lift up and remove the cut sheet feeder.

4.

Set DIP switch 1-8 to off (to turn off the cut sheet feeder mode).

Using the Printer Options

5-19

The Cut Sheet Feeder

5. Replace the clear plastic part of the printer cover with the clear plastic part that was on it originally.

6. Install the paper guide and printer cover.

Removal of the cut sheet feeder is now completed. Be sure to store the removed cut sheet feeder in its original box and packing materials.

5-20

Using the Printer Options

The Pull Tractor

The optional pull tractor

(C800141)

provides optimum continuous paper handling. The pull tractor is especially useful with continuous multi-part forms and labels. For best results, use the pull tractor along with the built-in push tractor as described in this section.

Installation

1.

Turn off the printer and remove the printer cover and paper guide.

2.

Remove the paper tension unit.

Using the Printer Options

5-21

The Pull Tractor

3.

Fit the rear notches on the tractor over the rear mounting pins in the printer.

Tilt the tractor unit toward you until the front latches click in place over the front mounting pins. Push down on the front latches to be sure they are firmly seated.

5-22 Using the Printer Options

The Pull Tractor

5. Pull the paper release lever all the way forward to the pull tractor position.

Paper Handling

1. Turn off the printer. Then set the first three holes of the continuous paper onto the built-in push tractor as described in the Using

Continuous Paper section in Chapter 2.

Using the Printer Options

5-23

The Pull Tractor

2. Now turn on the printer. Press the LOAD/EJECT button to load the continuous paper; then press the FORM FEED button. This advances the paper one page so that you can fit the paper onto the pull tractor.

Note: After

you

press the FORM FEED button, be careful not to touch any of the buttons on the control panel until step 9.

CAUTION:

Never use the platen knob while the printer is turned on. To adjust the loading position, use the micro-adjustment feature described in Chapter 3.

3. Open the sprocket covers of the pull tractor.

5-24 Using the Printer Options

4. Pull the sprocket lock levers toward you to release them.

The Pull Tractor

5. Adjust the sprocket units to match the width of the paper: then adjust the paper supports so that they are evenly spaced between the sprocket units.

Using the Printer Options

5-25

The Pull Tractor

6. Fit the holes in the paper over the tractor pins on the sprocket units.

If the paper does not fit exactly onto the tractor pins or if the paper buckles, press in on the pull tractor knob and turn it in the desired direction until the paper fits properly.

7. Close the sprocket covers.

5-26 Using the Printer Options

The Pull Tractor

8. See that the paper is not crooked or wrinkled and lock the sprocket units in place.

9. Install the paper guide.

Using the Printer Options 5-27

The Pull Tractor

10.

Slide the edge guides all the way apart.

11.

Replace the clear plastic part of the printer cover with the clear plastic part included with the pull tractor.

5-28

Using the Printer Options

12.

Install the pull tractor cover as shown below.

The Pull Tractor

13. Press the ON LINE button to set the printer on line.

Using the Printer Options

5-29

The Pull Tractor

Although the pull tractor can be used in combination with the built-in push tractor as described above, the pull tractor can also be used by itself. Instead of setting the paper on the pins of the push tractor, simply insert it through the same paper path as you would use with single-sheet paper.

CAUTION:

Do not use the short tear-off feature with the pull

tractor. Before you start printing with the pull tractor, be sure the

DIP switch

2-2 is set to off.

Removing the Pull Tractor

1. Make sure to tear off the printed document and remove the tractor cover and paper guide. Then turn on the printer.

5-30 Using the Printer Options

The Pull Tractor

2. Press the ON LINE button to set the printer off line. Then, press the

LOAD/EJECT

button until the continuous paper feeds backward out of the paper path to the standby position. The PAPER OUT light comes on when the paper is completely out of the paper path.

3. Push the paper release lever all the way back for single sheet paper

(as shown) or to the middle position for continuous feed paper.

Using the Printer Options 5-31

The Pull Tractor

4. Hold both ends of the tractor unit and slowly tilt

the

unit back.

5. Replace the paper tension unit as shown below.

5-32

Using the Printer Options

The Pull Tractor

6.

Replace the clear plastic part of the printer cover with the clear plastic part that was on it originally.

7.

Install the paper guide and printer cover.

Using the Printer Options

5-33

The Multi-Font Module

The optional Multi-Font Module gives you an easy way to have access to seven more fonts for your printer. After you install the Multi-Font

Module in its slot, you can use any one of the following fonts as your default font when the printer is turned on and any of the others optionally by sending a command to the printer.

CAUTION: Do not insert the Multi-Font Module when the printer is turned on.

These are samples of the character sets of the Multi-Font Module’s fonts:

Courier

We've just seen your excellent ad for

miniature zebras in a recent back issue of

Trader's Times. What is the price schedule for quantities over one gross?

Prestige

We've just seen your excellent ad for

miniature

zebras

in a recent back issue of

Trader's Times. What is the price schedule for quantities over one gross?

5-34

Using the Printer Options

The Multi-Font Module

Script

OCR-B

We've just seen your excellent ad for m i n i a t u r e z e b r a s in a recent back issue of

Trader's Times. What is the price for quantities over one gross?

schedule

OCR-A

We've just seen your excellent ad for m i n i a t u r e z e b r a s in

a

recent back issue of

Trader's Times. What is the price schedule for quantities over one gross?

The Multi-Font Module

Orator

W

E

V E J U S T S E E N Y O U R E X C E L L E N T A D F O R

M I N I A T U R E Z E B R A S I N A R E C E N T B A C K I S S U E O F

T

R A D E R

S

T

I M E S

. W

H A T I S T H E P R I C E S C H E D U L E

F O R Q U A N T I T I E S O V E R O N E G R O S S ?

Orator-S

We've just seen your excellent ad for

miniature zebras

in a recent back issue of

5-36

Using the Printer Options

The Multi-Font Module

Installation

1. Turn off the printer. See the font family table on page 5-39 and dial the rotary switch to the font of your choice.

2. Hold the module with the rotary switch on the top and plug it into the slot. (Set the rotary switch to on.)

Using the Printer Options

5-37

The Multi-Font Module

3. Turn the printer on; then select the SLOT by pressing the FONT switch on the operating panel until both indicator lights are lit.

WARNING:

Always turn off the power before inserting or removing the module; otherwise you may seriously damage

the

printer or the module.

Selecting a Font

This table

shows

the family numbers and characters per inch of the fonts in the Multi-Font Module.

Font name

Courier

Prestige

Script

OCR-B

OCR-A

Orator

OCR-S

Family number

2

5

6

3

4

7

8

Characters per inch

10,12,15

10,12,15

10,12,15

10

10

10

10

5-38 Using the Printer Options

The Multi-Font Module

There are two ways to select a font from the module: l

With

the

printer turned off:

— remove the Multi-Font Module from its slot on the right side of the printer l

— dial the rotary switch to the font of your choice

— return the module to the slot.

When the printer is turned on,

the

font selected becomes the default font if the slot is selected with the DIP switch setting or by pressing the FONT button

on

the central panel.

Send a software command, ESC k, to the printer to select the family number. See the Command Summary in Chapter 9 for details.

Note:

Some fonts may not include all of the characters shown on the samples.

Proportional spacing is not effective when printing any font in this module.

Numbers 0, 1, and 9 are not used.

Using the Printer Options

5-39

The Interface Boards

A number of optional interfaces are available in case your computer is either not provided with a parallel interface or you wish to increase the memory capacity of your printer’s buffer.

Choosing an Interface

Optional interfaces

can

described briefly below.

be divided into three main categories which are

IEEE-488 interfaces offer standardized connections, trouble-free operation, and

the

ability to connect computers, printers, and other devices on the same line so that they may share data freely.

The buffered parallel interfaces also offer trouble-free operation and standardized connections. They provide the printer with more memory to free the computer for other tasks when printing large amounts of text or graphics. You can increase the printer’s data buffering capacity by an additional 32 KB (about 10 pages).

Serial interfaces are required if your computer is not equipped with a parallel interface or if you need an interface that conforms to the

Current Loop standard instead of RS-232C. These interfaces also provide some combination of data communication protocol, loopback self test modes, and data buffers that increase

the the

following features: X-ON/X-OFF printer’s data buffering capacity.

If you are unsure whether you need an optional interface or would like to know more about interfaces, contact your Epson dealer.

5-40 Using the Printer Options

The Interface Boards

Compatible Interfaces

The following is a list of Epson interfaces that are compatible with your

LQ-1010 printer.

Interface number

#8143

#8148

#8165

#8172

Name

New Serial Interface

Intelligent serial interface

Intelligent IEEE-488 interface

32 KB buffered parallel interface

All Epson interfaces have the Epson name printed on them. If the board has an identification code printed on it, it is a four-digit number beginning with 8 and should correspond to one of the numbers listed in the table above.

Also, Coax and Twinax interfaces are available from third party vendors. These interfaces allow connectivity to mainframes and minicomputers and emulation of IBM printers. The Coax (EP-Connect) is available from Avatar Corporation

(508) 435-6872, and the Twinax

(I-08300) is available from I-O Corporation

(801) 973-6767.

Installation

1.

Turn off your printer. Then unplug the printer and disconnect the interface cable.

Using the Printer Options

5-41

The Interface Boards

WARNING:

High voltages are present inside the printer when the power is on. Do not attempt to remove the upper case unless the printer is turned off and the power cord is unplugged. Also, try not to touch contacts on the circuit board of the printer because many of the components can be destroyed by the static electricity present in your body

Do not change the settings of any DIP switches on the main board.

2. Remove the paper guide.

3. Remove the screw securing the interface board cover.

5-42 Using the Printer Options

4. Lift off the cover.

The Interface Boards

5.

Remove the screw labeled CG from the main board.

Using the Printer Options

5-43

The Interface Boards

Installing the board

There are two basic interface board designs-one with the FG wire not attached and one with the FG wire attached. This slight difference changes the way the boards are installed in the printer but does not affect the operation of the interface in any way. Check to see which type of interface board you have.

FG wire not attached

See next page

FG wire attached

Skip to page 5-47

5-44

Using the Printer Options

The Interface Boards

FG wire not attached

1. Use the CG screw to attach the round end of the FG (frame ground) wire to the main board and position the other end as shown.

2. Carefully insert the pins on the optional interface board into the mating connector on the main board; then secure the board with the screws provided.

Using the Printer Options

5-45

The Interface Boards

3. Attach the plug end of of the interface board.

the FG wire onto the FG pin located on top

4. Set the DIP switches on the interface board according to the manual accompanying it.

FG wire attached

1. Carefully place the interface board next to the printer as shown below. Use the CG screw to connect the round end of the FG

(frame ground) wire to the main board.

5-46 Using the Printer Options

The Interface Boards

2. Holding the interface board level, rotate it into position and attach it to the main board. Make sure that the connector pins are properly inserted into the mating connector.

3. Secure the board with the screws provided.

Using the Printer Options

5-47

The Interface Boards

4. For all interface boards except #8143 New Serial Interface board, set the DIP switches on the interface board according to the manual accompanying it. If you

have the #8143, see

page

5-50.

Attaching the interface board cover

1.

Bend back the hinge plate

on

the interface board cover as shown below.

Note: When

you reattach the interface board, rebend

the

plate to cover the opening. The plate is sturdy, but be careful not to subject it to excessive bending.

5-48 Using the Printer Options

2. Reattach the board cover.

The Interface Boards

CAUTION: When an optional interface board is installed, be sure to disconnect the printer cable from the printer’s built-in parallel interface. Two interface cables must not be connected at the same time.

#8143 New Serial Interface

If you are using an optional interface, it may be necessary for you to alter the communication protocol of the printer or the computer so that they can communicate properly. In most cases, you should use the information in your optional interface manual or your computer’s manual to match the computer with the interface.

If you are using the #8143 optional interface board, make sure that you read through the section below on baud rate selection. You may also want to see the following sections on handshaking timing and error handling for interface information specific to the

LQ-1010

printer.

For all other data transfer conventions, such as word structure or communications protocol, use the information in the manual supplied with your #8143 optional interface.

Using the Printer Options 5-49

The Interface Boards

Baud rate selection

You can select baud rates from

75

to

19,200

BPS (Bits Per Second).

When setting the baud rate, make sure you use the bit rate selection table for printers with buffers (in

the #8143

interface manual).

For more information on the

LQ-1010’s

input buffer settings, see the section on DIP switch functions in Chapter 3 of this manual.

Handshaking timing

When the vacant area for data in the input buffer drops to the printer outputs an X-OFF code or sets the DTR flag to indicating that it cannot receive data.

256

bytes,

“1” (MARK)

Error handling

When a parity error is detected, your printer prints an asterisk (*). All other errors, including framing and overrun, are ignored.

5-50 Using the Printer Options

Chapter 6

Maintenance

Cleaning the Printer ........................................................... 6-2

Replacing the Ribbon ............................................................. 6-5

Transporting the Printer ................................................................... 6-11

Maintenance 6-1

Cleaning the Printer

To keep your printer operating at its best, you should clean it thoroughly several times a year. Follow the steps below:

1. Make sure that the printer is turned off. Then remove the paper guide or the cut sheet feeder.

6-2

Maintenance

Cleaning the Printer

2. Using a soft brush, carefully remove all dust and dirt.

3.

If the outer case or paper guide is dirty or dusty, clean it with a soft, clean cloth dampened with a mild detergent solution. Keep the printer cover in place to prevent water from getting inside the printer.

Maintenance 6-3

Cleaning the Printer

WARNINGS:

l

Never use alcohols or thinners to clean the printer, since these chemicals can damage the components as well as t h e c a s e .

l l l

Be careful not to get water on the printer mechanism or electronic components.

Do not use a hard or abrasive brush.

Do not spray the inside of the printer with lubricants; unsuitable oils can damage the mechanism. Contact your

Epson dealer if you think lubrication is needed.

6-4 Maintenance

Replacing the Ribbon

Replace the ribbon when the printout becomes too faint. The standard ribbon cartridge or

#7770

film ribbon cartridge are

#7754

recommended for the LQ-1010 printer. Do not use ribbons designed for nine-pin printers.

1. Make sure that the printer is turned off. Then remove the printer cover.

Maintenance 6-5

Replacing the Ribbon

2.

Remove the paper tension unit.

3. To remove the ribbon cartridge, grip it by the black plastic handles and lift the cartridge straight up and out of the printer.

WARNING:

If the printer has just been used, the print head may be hot. Let it cool before attempting to replace the ribbon.

6-6

Maintenance

4. Slide the print head to the middle of the printer.

Replacing the Ribbon

5. To remove slack in the new ribbon, turn the ribbon-tightening knob in the direction of the arrow.

Maintenance 6-7

Replacing the Ribbon

6.

Push the new ribbon cartridge firmly into position, making sure the plastic hooks fit into the slots, as shown below.

Note: Press lightly on both sides of the cartridge to make sure the hooks are properly inserted.

6-8 Maintenance

Replacing the Ribbon

7.

Use a pointed object, such as a ball point pen, to guide the ribbon between the print head and ribbon guide while you turn the ribbon-tightening knob to help feed the ribbon into place. Be careful not to puncture the ribbon.

8. Slide the print head from side to side to make sure it moves smoothly. Also see that the ribbon is not twisted or creased.

Maintenance 6-9

Replacing the Ribbon

9 .

Attach the paper tension unit.

10.

Insert the hooks on the printer cover unit into the printer, and then tilt the printer cover back into place.

6-10 Maintenance

Transporting the Printer

Before you transport your printer some distance, carefully repack it in the original box and packing materials according to the following instructions.

1. Make sure the printer is turned off. Then remove any installed options, as well as the paper guide and printer cover.

WARNING: Turn the printer off before unplugging the power cable from the AC outlet.

2. Unplug the power cable from the electrical outlet. Coil the cable and tie it; then disconnect the interface cable from the printer and the computer.

3. Remove the paper tension unit.

Maintenance

6-11

Transporting the Printer

4. Remove the ribbon cartridge.

5. Attach the locking clip as shown below.

WARNING: You must attach the locking clip when you transport the printer.

6-12

Maintenance

Transporting the Printer

6. Reattach the paper tension unit, locking it securely in place.

7. Remove the platen knob.

Maintenance

6-13

Transporting the Printer

8. Reattach the printer cover, then replace the packing materials and put the printer in its box.

6-14 Maintenance

Chapter 7

Troubleshooting

Problems and Solutions ................................................................. 7-2

Power Supply ................................................................................ .. 7-4

Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5

Paper Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24

Troubleshooting 7-1

Problems and Solutions

This chapter discusses problems you may encounter while operating your printer and their likely solutions. If you are having difficulty achieving the desired printing result, first locate the problem in the table below and then see the appropriate page for the solution.

Power supply

l

Power is not being supplied,

See 7-4 l l l l

Printing

The printer does not print.

l

The print is faint or uneven.

Dots are missing in the printed characters or graphics.

Printed characters are not what you expected.

The print position is not what you expected.

See 7-5

See 7-6

See 7-7

See 7-8

See 7-11 l

Paper handling

Single sheets do not feed properly.

l

Continuous paper does not feed properly.

l l

Switching between single sheets and continuous paper cannot be performed properly.

The short tear-off function does not operate properly.

See 7-14

See 7-17

See 7-21

See 7-23

7-2 Troubleshooting

Problems and Solutions

Options

l

Using the cut sheet feeder, the paper does not feed properly.

l l l

Using the pull tractor with the push tractor, continuous paper does not feed properly.

Using the font module, the module’s fonts do not print.

Using an optional interface, the printer does not operate properly.

See 7-24

See 7-28

See 7-32

See 7-32

Troubleshooting 7-3

Power Supply

Problem

Power is not being supplied.

The POWER light does not go on.

Solution

The power cable may be loose or not properly plugged into the electrical outlet.

Turn off the printer, see that the power cable is properly plugged in to the electrical outlet, and turn the printer back on.

The power switch is off. Turn on the switch.

Power is not being supplied to the electrical outlet. Plug another electrical device into the outlet to determine whether the outlet is operating properly. If the electrical outlet is controlled by a switch, use an electrical outlet that is not controlled by an outside switch.

7-4

Troubleshooting

Printing

Problem

The printer does not print.

The ON LINE light is on but nothing is printed.

Solution

The ON LINE light is off.

The PAPER OUT light is on.

The software may not be installed properly for your printer. Check the printer settings and make the necessary changes.

The interface cable may be loose. Check both ends of the cable between the printer and the computer. Secure the connector using the wire retaining clips.

You may not be using the correct interface cable. Make sure your interface cable meets the printer and the computer specifications.

The printer may be off line and cannot receive data. Press the ON LINE button. The

ON LINE

light should go on. See Chapter 3.

The printer may be out of paper. Load more paper into the printer. See Chapter 2.

The paper may be set too far to the right, so that the paper detector cannot sense it.

Move the paper a little to the left. The

PAPER OUT

light should go off.

Troubleshooting 7-5

Printing

Problem

The printer does not print (continued).

The printer sounds like it is printing, but nothing is printed.

The printer makes a strange noise, the beeper sounds several times, and the printer stops abruptly.

The ON LINE light is flickering but the printer does not print, or it stops printing abruptly.

The print is faint or uneven.

Printed characters have parts missing at the bottom as shown here.

A B C D

Solution

The ribbon cartridge may not be installed properly. Turn off the printer, reinstall the ribbon cartridge, and take up any slack in the ribbon.

The ribbon may be worn. Replace the ribbon cartridge. See Chapter 6.

This indicates an error in printer operation.

Turn off the printer, check for paper jams or other problems; then turn the printer back on. If the printer still does not print correctly, contact your Epson dealer.

The print head is overheated. Wait a few minutes; the printer resumes printing automatically when the print head cools.

The ribbon cartridge may not be installed properly. Remove the ribbon cartridge and reinstall it. Make sure the cartridge hooks are inserted securely into the printer. See

Chapter 1.

7-6

Troubleshooting

Printing

Problem

The print is faint or

uneven (continued).

The printout is faint.

Solution

The ribbon may be worn out. A worn ribbon can damage the print head and should be replaced. Install a new ribbon cartridge. See Chapter 6.

The paper thickness lever may not be set correctly for the paper you are using. Set the paper thickness lever to match the thickness of your paper. See Chapter 2.

Dots are missing in the

printed characters or

graphics.

A line of dots is missing in the printout.

A B C D

Dots are missing in random positions.

A B C D

The print head is damaged. Stop printing and contact your Epson dealer to have the printer repaired.

There is either too much slack in the ribbon or the ribbon has come loose and gotten caught on something. Stop printing, turn off the printer, and reinstall the ribbon cartridge. See Chapter 6.

Troubleshooting 7-7

Printing

Problem

Printed characters are

not what you

expected.

The typestyle or characters that are set by the software cannot be printed.

The Roman, Suns

Serif, or Draft font is selected in your software, but the characters are printed in a different font.

Italic characters are printed instead of the selected graphic “line” characters.

Solution

The software may not be correctly installed for your printer. Use the program’s setup

(or install) procedure to check the printer settings, and reset as needed.

The wrong font is selected. If your program accepts control codes, set the codes to the values below to select the built-in fonts:

Roman:

Sans Serif:

Draft:

ESC k 0

ESC k 1

ESC x 0

See Chapter 3.

The wrong character table is selected. If your application program is capable of sending control codes, specify the Epson

Extended Graphics character table using

ESC t 1.

You can also select the graphics character table by changing a DIP switch setting. To do this, turn off the power, set DIP switch

1-7 to on, then turn on the printer. See

Chapter 3.

7-8

Troubleshooting

Printing

Problem

Printed characters are not what you expected

(continued).

Graphic characters or fines are being printed instead of the selected italic characters.

The wrong international characters are being printed.

Solution

The wrong character table is selected. If your application program is capable of sending control codes, specify the italic character table using ESC t

0.

You can also select the italic character table by changing a DIP switch setting. To do this, turn off the power, set DIP switch 1-7 to off; then turn on the power. See

Chapter 3.

The wrong international character set is selected. If your application program is capable of sending control codes, specify

the

desired international character set using

ESC R n. See the description of ESC R in

Chapter 9.

You can also select the international character table by changing DIP switch settings. To do this, turn off the power and set DIP switches

1-1, 1-2,

and

1-3

to the correct positions for the character set you

want.

See Chapter 3.

Troubleshooting 7-9

Printing

Problem

Printed characters are not what you expected

(continued).

The characters printed are smaller than expected.

The typestyle selected by SelecType is not printed.

Characters cannot be defined using ESC & and ESC :

Solution

The condensed mode may be set. Check to

see

if the CONDENSED light on the control panel is on. If it is lit, press the CONDENSED button to cancel the mode.

Also, if your application program is capable of sending control codes, you can cancel the condensed mode by sending the

DC2 code to the printer. See Chapter 9.

The software may not be properly installed for your printer. Use the program’s setup

(or install) procedure to check the printer settings and reset as needed.

Your software may be overriding your

SelecType setting. If your program allows you to change the printing style, software control will override the SelecType settings. For these application programs use the program, not SelecType, to change typestyles.

User-defined character mode may not be selected. When defining characters, make sure that DIP switch 2-5 is set to off.

7-10

Troubleshooting

Printing

Problem

The print position is not what you expected.

Printing starts too high or too low on the

Page.

One line of printing

has taken up two lines.

Line spacing is incorrect.

Solution

The loading position may be incorrect.

micro-adjustment to adjust the loading

Use position. See Chapter 3. If the problem persists, check the top margin set by your application software and adjust it.

Auto line feed may be on. Turn off DIP switch

2-4.

The margin setting may not be correct. Use your application program to change the margin.

In BASIC, enter either of the following statements:

WIDTH LPRINT

255

WIDTH "LPT1"

255

If the printer still does not print properly, set the right margin to the maximum setting using ESC Q. See Chapter 9.

Line spacing is too tight or too far apart.

Use your application program to specify line spacing using ESC 0, ESC

ESC A. See Chapter 9.

2,

ESC

3,

or

Troubleshooting 7-11

Printing

Problem

The print position is not what you expected

(continued).

Page length does not match the length of the paper.

Regular gaps occur in the printout.

Skip over perforation is set, but the perforation does not fall in the center of the skip.

Solution

Check the page length set by your application software and adjust it if necessary, or change the page length setting with DIP switch 2-1.

If you are using the cut sheet feeder, the self test function prints the number of printable lines that can fit on a single sheet. Use this feature to determine the correct page length setting. See Chapter 3.

One-inch skip over perforation may be set.

Set DIP switch 2-3 to off, or use your application program to cancel skip over perforation. See Chapter 3.

The loading position of the paper may be too high or too low. Use the microadjustment feature to reset the loading position so that the perforation is centered within the skip area.

Your application program may be setting the top and bottom margins. If this is the case, turn off skip over perforation by setting DIP switch 2-3 to off.

The page length for continuous paper may be set incorrectly. Set DIP switch 2-1 to 11 or 12 inches. See Chapter 3.

7-12 Troubleshooting

Printing

Note: Use the data dump mode to check data being sent from the computer. In the data dump mode, data is printed in hexadecimal format and in

ASCII

characters. See Data Dump Mode in Chapter 3.

If the printer still does not print, try the self test described in Chapter 1.

If the self test works properly, the printer is all right, and the problem probably lies in the computer, the software, or the cable. If the self test does not work, contact your Epson dealer.

Troubleshooting

7-13

Paper Handling

The following section guides you through problems in handling single sheets and continuous paper. If you are having problems using the optional cut sheet feeder or pull tractor, see the section on options later in this chapter.

Problem Solution

Single sheets do not feed properly.

The LOAD/EJECT button was pressed, but the platen did not moue and paper was not fed.

You may be trying to feed paper using one of the control panel buttons while the printer is on line (ON LINE light is on). Press the ON LINE button once to set the printer off line; then feed the paper. After feeding the paper, press the ON LINE button again to set the printer on line. See Chapter 3.

The left edge guide may be set too far to the right so that the paper detector cannot sense it. Move the paper a little to the left.

The PAPER OUT light should go off.

7-14 Troubleshooting

Paper Handling

Problem

Single sheets do not feed properly

(continued).

The LOAD/EJECT button was pressed and the platen rotated, but paper was not fed.

When the LOAD/EJECT button is pressed, the paper jams.

Solution

The paper release lever may be set in the wrong position. Push paper release lever back to the single-sheet position. See

Chapter 2.

The left and right edge guides may be too close together, preventing the paper from feeding smoothly. Adjust the position of the edge guides so that the paper can move up and down freely. See Chapter 2.

The paper may not be firmly inserted.

When feeding thicker than normal paper, press down lightly on the paper while pressing the LOAD/EJECT button.

The cut sheet feeder mode may be turned on (DIP switch 1-8 is on). When the cut sheet feeder is not in use, DIP switch 1-8 should be off. See Chapter 3.

The edge guides may be too far apart.

Adjust the edge guides to the width of the paper.

The dimensions of the paper may exceed the specified limitations. Use only paper sizes that are within the specified range.

Multi-part forms cannot be used with this printer’s single-sheet feeding system. See

Chapter 8.

Troubleshooting 7-15

Paper Handling

Problem

Single sheets do not feed properly

(continued).

When the LOAD/EJECT button is pressed, the paper feeds through and then out of the printer.

The paper feed is crooked.

The paper does not fully eject.

Solution

The paper may have been between the edge guides before the printer was turned on.

When loading single sheets, be sure that paper is not in the paper guide before you turn the printer on.

The paper guide may not be attached, or it may not be in the correct position. When printing on single sheets, use the paper guide in its upright position.

The paper may be dog-eared. Use new

paper.

You may be trying to eject the paper using the FORM FEED button. Always press the

LOAD/EJECT button to eject the paper.

The page length setting may be wrong. If the page length is incorrectly set by your software, the paper may not fully eject.

Check your software settings.

7-16 Troubleshooting

Paper Handling

Problem

Continuous paper does not feed properly.

When the LOAD/EJECT button is pressed, the platen does not rotate and paper does not feed.

When the LOAD/EJECT button is pressed, the platen rotates but paper does not feed.

Solution

You may be trying to feed paper using the control panel buttons while the printer is

on

line (ON LINE light on). Press the ON LINE button once to set the printer off line, then try feeding paper. After feeding paper, press the ON LINE button again to set the printer on line. See Chapter 3.

The paper release lever may be pushed back to the single-sheet position. When using the pull tractor, be sure the paper release lever is pulled forward to the continuous paper position. See Chapter 2.

Continuous paper may have already been in the paper path. (In this case, the paper feeds backward to the standby position.)

Press the LOAD/EJECT button again to load the paper.

Troubleshooting 7-17

Paper Handling

Problem

Continuous paper does not feed properly

(continued).

The paper feed is crooked or the paper jams.

Solution

The paper

supply may be obstructed by a cable or some other object. Make sure that the paper feeds smoothly into the printer.

See Chapter 2.

Your supply of continuous paper may be too far from the printer. Position your

paper

supply within 3 feet (1 meter) of the printer. See Chapter 2.

The paper may be caught on the edge guides. When using continuous paper, make sure that the paper guide is lowered to the horizontal position and that the edge guides are positioned as far apart as possible. See Chapter 2.

The holes on the sides of the paper may not be aligned with each other. Reposition

the

paper on the tractor pins. See

Chapter 2.

The sprocket units are incorrectly positioned for the paper width. Move the right sprocket unit to remove any slack across the width of the paper. See

Chapter 2.

The position of your paper supply may be preventing it from feeding straight. See

Chapter 2.

7-18 Troubleshooting

Paper Handling

Problem

Continuous paper does not feed properly

(continued).

The paper feed is crooked or the paper james (continued).

Regular gaps occur in the printout.

Skip over perforation does not function.

Solution

The sprocket lock levers may be unlocked, or the sprocket covers may be open.

Position the sprocket units to match the width of your paper. Then, lock them in place by pressing the sprocket lock levers away from you. See Chapter 2.

The paper guide may be in the upright position. When using continuous paper, make sure that the paper guide is in the lowered position so that it can act as a paper separator. See Chapter 2.

The paper thickness lever may be in the wrong position. For printing on ordinary paper, always set the lever to position 2.

The paper dimensions may exceed the specified limitations. Use only paper sizes that are within the specified range. Your printer can print on continuous multi-part forms consisting of 1 original and 1 or 2 copies. See Chapter 8.

Skip over perforation may be interfering with your application program settings. Set

DIP switch 2-3 to off.

You may not have turned off the power after setting DIP switch 2-3 to on. To make new DIP switch settings effective, turn the power off, then on again.

Troubleshooting

7-19

Paper Handling

Problem

Continuous paper does not feed properly

(continued).

Skip over perforation is set, but the perforation does not

fall in the center of the

skip.

The loading position of the paper shifts slightly while printing several pages.

After printing stops, the paper automatically feeds forward.

The short tear-off function is selected

(DIP switch 2-2 is on), but it does not work.

Solution

The page length for one page of continuous

paper

may be set incorrectly. Change the setting of DIP switch 2-1.

The loading position of the paper may be too high or too low. Use the microadjustment to reset the loading position.

The paper you are trying to feed may be too heavy for the built-in push tractor.

When highly accurate paper feed is necessary, such as when printing carbon copies, use the optional pull tractor.

The short tear-off function may be selected.

When you resume printing, the paper feeds backward to its loading position. If you do not need this function, set DIP switch

2-2

to off. See Chapter 3.

You may not have turned off the power after setting the DIP switch. To make new

DIP switch settings effective, turn the power off, then on again.

There may still be data in the print buffer.

The short tear-off function works only if the data in the print buffer is completely printed and the next print position is at the top of the next page.

7-20 Troubleshooting

Paper Handling

Problem

Continuous paper does not feed properly

(continued).

The short tear-off function is selected

(DIP switch 2-2 is on), but it does not work

(continued).

The LOAD/EJECT button is pressed to eject the paper the paper feed stops, and paper does not fully eject or it jams.

Solution

Your program may not be sending a form feed command to the printer. At the end of your program or the page, send a form feed (FF). If you are using BASIC, be sure to add a semicolon (;) after the FF code to prevent any additional codes from being sent to the printer.

You may have tried to back feed too many pages. Before ejecting the paper, always tear off the last printed page. See Chapter 3.

You may be trying to eject labels. Labels may jam when they are fed backward, so always use the FORM FEED button and feed labels forward to eject them.

Switching between single sheets and continuous paper cannot be performed properly.

When the LOAD/EJECT button is pressed to load continuous paper, the platen does not rotate and the paper is not loaded.

Pull the paper release lever forward to the continuous paper position, set the paper, then press the LOAD/EJECT button.

Troubleshooting

7-21

Paper Handling

Problem

Switching between single sheets and continuous paper cannot be performed properly (continued).

The paper release lever is correctly set for continuous paper, but when the LOAD/EJECT button is pressed, the platen rotates backward and the paper comes off the sprockets.

When the LOAD/EJECT button is pressed to loud a single sheet from the sheet guide, the platen rotates in reverse, the single sheet does not load, and the continuous paper comes off the sprockets.

Solution

A

single

sheet may be in the paper guide, causing the continuous paper to back out and to come off the sprockets. When using continuous paper, always make sure to remove any single sheets remaining in the paper guide.

The paper release lever may not be in the proper position. Push the lever back to the single-sheet position.

7-22 Troubleshooting

Paper Handing

Problem

Switching between single sheets and continuous paper cannot be performed properly (continued).

Even with the paper release lever set correctly to the single-sheet position, the single sheet and continuous paper feed together and jam.

Solution

The continuous paper may not have fed backward far enough to reach the standby position before you changed the position of the paper release lever. Remove the jammed paper and try again. Also, check that the

PAPER OUT

light comes on before changing the position of the paper release lever to make sure that the continuous paper is completely ejected. When there is more than one page to feed backward to eject, you must press the

LOAD/EJECT

button at least two times.

The short tear-off function does not operate properly.

One page is completely printed, but the paper does not feed.

Printing ended in the middle of a page.

DIP switch 2-2, short tear-off mode, may be set to off. Set DIP switch 2-2 to on to turn on the short tear-off mode.

One page of data may not have been sent to the printer. Finish the page by sending a form feed code (FF) to the printer or by sending enough line feed codes (LF) to advance the remainder of the page.

Troubleshooting 7-23

Options

Problem

Using the cut sheet feeder, the paper does not feed properly.

The LOAD/EJECT button is pressed, but the platen does not move and the paper does not feed.

After a print

command is sent from the computer, the platen does not move and the paper does not

feed.

Solution

You may be pressing the

LOAD/EJECT

button while the printer is on line. Always put the printer off line before feeding the paper. Paper feeds automatically when the cut sheet feeder receives a print command from the computer (only while the printer is on line).

The printer may be off line. Press the ON

LINE

button to put the printer on line.

The cut

sheet

feeder mode may be off. Set

DIP switch

1-8

to on. If your program allows you to use control codes, use ESC

EM 4 to set the cut sheet feeder mode. The printer must be ready with

no

paper out condition to receive this command. Send the command with continuous paper loaded and with the paper select lever in the continuous paper position.

7-24 Troubleshooting

Options

Problem

Using the cut sheet feeder, the paper does not feed properly

(continued).

After a print command is sent from the computer, the platen rotates, but paper does not feed.

The PAPER OUT light is on.

Solution

DIP switch 1-8 is set to off. DIP switch 1-8 must be set to on in order to use the cut sheet feeder. See Chapters 3 and 5.

The cut sheet feeder may be incorrectly installed on the printer. Remove and reinstall the cut sheet feeder making sure that the mounting notches are properly mated with the pins on the printer. See

Chapter 5.

The cut sheet feeder may be out of paper.

Load more paper in the cut sheet feeder’s bin.

The paper release lever may not be in the single-sheet position. Push the lever back to the single-sheet position. See Chapter 5.

The paper set levers may be pulled forward. After loading a stack of paper in the cut sheet feeder, push the paper set levers backward. See Chapter 5.

The left and right paper guides may be too close together, preventing smooth paper feed. Adjust the position of the paper guides so that the paper can move up and down freely. See Chapter 5.

Troubleshooting

7-25

Options

Problem

Using the cut sheet feeder, the paper does not feed properly

(continued).

After a print command is sent from the computer, the platen rotates, but paper does not feed.

The PAPER OUT light is on (continued).

Two or more sheets feed at the same time.

Solution

Paper may be jammed near the print head.

Remove the paper jam (temporarily remove the cut sheet feeder if necessary).

You may have loaded too many sheets in the cut sheet feeder’s bin. Remove the sheets. The bin can hold a maximum of 150 sheets.

There may be only one sheet left in the bin.

The last sheet in the bin may not feed, so add more paper.

You may have loaded too many sheets in the cut sheet feeder’s bin. Remove the sheets. The bin can hold a maximum of 150 sheets.

You may have forgotten to fan the stack of paper before loading it into the bin.

Remove the paper and fan it. Then align the edges of the stack. See Chapter 5.

7-26

Troubleshooting

Options

Problem

Using the cut sheet feeder, the paper does not feed properly

(continued).

The paper feed is crooked.

Solution

You tried to manually insert a single sheet, but instead paper was fed from the cut sheet

feeder’s

bin.

The paper

may be old or creased. Discard it and load new, clean sheets of paper.

The left and right paper guides

may

be too far apart. Adjust the paper guides to

the

width of the paper.

There may be too much outgoing paper.

Never let more than 80 sheets of outgoing paper accumulate while printing.

The weight of your paper may be too heavy or too light for the cut sheet feeder.

Refer to

the

specifications in Chapter 8 and make sure that your paper is the proper size and quality.

The single sheet may have been inserted in

the

wrong place. Check it and try again.

See Chapter 5.

Paper may feed from the bin if you try to insert several single sheets. To insert several single sheets, pull the paper set lever forward.

Troubleshooting

7-27

Options

Problem

Using the cut sheet feeder, the paper does not feed properly

(continued).

One page of printing has spread to two pages.

Solution

The page length setting may be wrong.

Run a self test in cut sheet feeder mode.

The printer will automatically measure the paper loaded and set the correct page length. See Chapter 5.

You may have to change the top or bottom margin or page length for your application program.

Using the pull tractor with the push tractor, continuous paper does not feed properly.

The FORM FEED or

LINE FEED button was pressed, but the paper does not feed at all.

(Platen does not rotate.)

The printer may be on line. Before using the control panel buttons to feed paper, always put the printer off line (ON LINE light out).

7-28 Troubleshooting

Options

Problem

Using the pull tractor with the push tractor, continuous paper does not feed properly

(continued).

Paper feed is crooked or the paper jams.

Solution

Something may be obstructing the paper feed, like an object on top of the paper stack or a cable caught on the paper. Make sure that nothing prevents the smooth flow of paper and position the paper so that it feeds straight in line with the sprockets.

The supply of paper may be too far from the printer. Position the paper supply so that it is less than three feet or one meter away.

The paper may be caught on the edge guides. When using continuous paper, make sure that the paper guide is folded backwards over the paper and that the edge guides are moved to each edge of the paper guide. See Chapter 2.

The pull tractor and push tractor sprockets are not aligned correctly. When using both tractors, be sure that the sprockets on both are positioned evenly.

Troubleshooting:

7-29

Options

Problem

Using the pull tractor with the push tractor, continuous paper does not feed properly

(continued).

Paper feed is crooked or the paper jams

(continued).

Solution

Several lines of space occur in the printout.

Skip over perforation is set, but does not

work.

Skip over perforation is set, but the skip has shifted from the perforation, or the perforation does not fall in the center

of

the skip.

The paper

may be slack. Adjust the position of the sprockets to take up any slack along the width of the paper. Remove slack lengthwise by pressing in and rotating the pull tractor knob on the right. Do not turn the platen knob.

The paper thickness lever may not be correctly set. Set the paper thickness lever to match the thickness of your paper.

The paper may not meet the specifications.

Check that your paper is the proper size, weight, and thickness.

Skip over perforation may be set. Set DIP switch 2-3 to off.

You may have set the DIP switches with the power on. To make new DIP switch settings effective, turn the power off, then on again.

The loading position of the paper may be too high or too low. Use the microadjustment feature to reset the loading position.

7-30

Troubleshooting

Options

Problem

Using the pull tractor with the push tractor, continuous paper does not feed properly

(continued).

Skip over perforation is set, but the skip has shifted from the perforation, or the perforation does not fall in the center of the skip (continued).

When the printing ends the paper feeds abruptly, and as it resumes printing, the paper feeds backward and comes off the pull tractor sprockets.

When the LOAD/EJECT button is pressed to eject the paper the paper comes off the pull tractor sprockets.

Solution

The page length for one page of the continuous paper may be set incorrectly.

Set DIP switch 2-1 or use your application program control codes to set the correct page length.

The short tear-off function may be selected.

The short tear-off function cannot be used with the pull tractor, so be sure to set DIP switch 2-2 to off. See Chapter 3.

When the paper release lever is in the continuous paper position, the paper feeds backward to eject. When using the pull tractor, press the

FORM FEED

button to feed the paper forward to eject.

Troubleshooting 7-31

Options

Problem

Using the font module, the module’s fonts do not print.

The font module is set, but the fonts in the module do not print.

Solution

The font module may not be fully inserted in the slot. Check it and insert the module properly if necessary.

The font module may be inserted the wrong way. Align the (>) marks on the module and the slot and insert it properly.

The font in the module may not be correctly selected. Select the slot by pressing the

FONT

button on the control panel.

If your program allows you to use control codes, use ESC k command to select the font.

Using an optional interface, the printer does not operate properly.

The printer does not print or the printout is not what you expected.

The interface board may be loose or not properly connected. Check that the interface board is correctly inserted into the connector on the main board.

7-32 Troubleshooting

Options

Problem

Using an optional interface, the printer does not operate properly (continued).

The printer does not print or the printout is not what you expected

(continued).

Solution

You may be trying to use an interface with the wrong specification. Check the specifications to make sure that you can use the interface with this printer.

You may be trying to use a cable with the wrong specification. Make sure that the cable matches the specifications of the interface.

The DIP switches or jumpers on the interface board may be set wrong. See the interface manual for the correct settings.

The interface settings on the computer may be wrong. See your computer manual for the correct settings.

The computer and interface settings may not match. Match the settings for each condition.

Two cables may be installed on the printer; only one cable may be attached at any time.

Troubleshooting

7-33

Options

If the printer still does not operate properly after checking the above points, run a self test of the interface to make sure that there are no on-board defects. If any abnormality is found, contact your Epson dealer.

7-34 Troubleshooting

Chapter 8

Technical Specifications

Printer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8

Pin Assignments for the Parallel Interface . . . . . . . . . . . . . . 8-8

Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

Printing Enabled/Disabled Signals and Control Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-11

Option Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

Single-bin Cut Sheet Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14

Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14

Technical Specifications 8-1

Printer Specifications

Printing

Print method:

Print speed:

24-pin impact dot matrix

Quality

Draft

LQ

Printing direction:

Line spacing:

Paper feed speed:

(continuous feed)

Characters per inch

10

12

10

12

Characters/second/line

150

180

50

60

Bidirectional logic-seeking for text printing.

Unidirectional for graphics.

1/6

inch or programmable in increments of

1/360th of an inch

Single sheet: 2.2 inches per sec

(100 ms/line)

Continuous: 2.2 inches per sec

(100 ms/line)

Printable columns:

Character spacing

10 cpi

10 cpi condensed

12 cpi

12 cpi condensed

Input buffer:

Maximum printed characters

136

233

164

272

8 KB/1 KB

(DIP switch selectable)

8-2 Technical Specifications

Printer Specifications

Optional fonts:

LQ Epson Courier

LQ Epson Prestige

LQ Epson Script

LQ Epson OCR-B

LQ Epson OCR-A

LQ Epson Orator

LQ Epson Orator-S

Character fonts:

F o n t

Epson Draft

Epson Roman

Epson Sans Serif

Characters:

Available sizes

(Characters per inch)

10, 12, 15

10, 12, 15, Proportional

10, 12, 15, Proportional

96 standard ASCII character set (including italic characters)

15 international character sets (including a legal symbol set)

Epson Extended Graphics character set

Paper

Paper width:

Paper length:

Single sheet

Continuous

Envelope

Labels

(continuous only)

Single sheet

7.2

to

14.3

inches

(182

to 364 mm)

4 to 16 inches

(101

to 406 mm)

6.5 or 9.5 inches

(166

or 240 mm)

2 1/2 x 15/16 inches

(minimum)

(63.5 x 23.8

mm)

7.2 to 14.3 inches

(182

to 364 mm)

Technical Specifications 8-3

Printer Specifications

Printable area:

Single sheet

0.12 inches (3 mm) or more

0.33 inches (8.5 mm) or more

0.12 inches (3 mm) or more

Continuous paper

0.53 inches (13.5 mm) or more

0.35

inches (9 mm)

0.51 inches (13 mm) or more (both sides) when the 4 to 14.9 inch

(101 mm to 378 mm) width paper is used.

1.02 inches (26 mm) or more (both sides} when the 15 to 16 inch

(381 to 406 mm) width paper is used.

8-4 Technical Specifications

Printer Specifications

Envelope

0.33 inches (8.5 mm) or more

0.87 inches (22 mm) or more

0.12 inches (3 mm) or more

Note:

Envelope printing is only available at normal temperature.

Load

the

envelope with its long side horizontal.

Paper weight :

Paper thickness:

Single Sheet

Continuous

Multi-part forms

Envelope

Single Sheet

Continuous

Envelope

Label

(with backing)

14

lb to

24

lb

14

lb to

22

lb

12

lb to

15

lb per sheet

Maximum number sheets = 3

12

lb to

24

lb

0.0025 to 0.0055 inches

(0.065

to

0.14

mm)

0.0025 to 0.01 inches

(0.065

to

0.25

mm)

0.0063

to

0.0197

inches

(0.16

to

0.52

mm)

0.01 inches

(Maximum 0.28 mm)

Technical Specifications 8-5

Printer Specifications

Copy capacity:

Up to

3 sheets

including the original. Total thickness must not exceed 0.01 inches

(0.25

mm).

Note:

Label printing and the printing of

24

lb paper are available only at normal temperature and normal humidity.

Mechanical

Paper feeding methods:

Ribbon:

Life

expectancy

of ribbon:

Friction

Push tractor

Cut sheet feeder (optional)

Pull tractor (optional)

Cartridge ribbon, available in black:

#7754

#7770

(film)

#7754: 2,000,000 characters

(in Letter Quality characters, at 48 dots/character)

MCBF:

#7770:

200,000

characters

(in Letter Quality characters, at 48 dots/character)

For all components excluding print head:

3,000,000

lines

6000

power on hours (duty

25%)

MTBF:

Print head life:

200,000,000

strokes/wire

Dimensions and weight: (excluding knobs and paper guides)

Height:

5.69

inches

(144.5

mm)

Width:

Depth:

Weight:

23.35

inches

(593.0

mm)

13.66

inches

(347.5

mm)

18 lbs (8 kg approx.)

8-6

Technical Specifications

Printer Specifications

Electrical

Voltage:

Power consumption:

Frequency:

Insulation resistance:

Dielectric strength

(between AC line and

chassis):

120 VAC ± 10%

100 watts maximum

50 ± 0.5 Hz, 60 ± 0.5 Hz

10 Mohms between AC power line and chassis

Can withstand 1.0 kV rms applied for one minute, or 1.2 kV applied for one second

Environment

Temperature:

Humidity:

Shock:

Vibration:

Operation angle:

Operation: 40°F to 95°F (5°C to 35°C)

Storage: -22°F to 140°F (-30°C to 60°C)

Operation:

Storage:

10% to 80% (noncondensing)

5% to 85% (noncondensing)

Operation: Up to 1 G within 1 ms

Storage: Up to 2 G within 1 ms

Operation: Up to 0.25 G at up to 55 Hz

Storage: Up to 0.50 G at up to 55 Hz

Less than 15º (without cut sheet feeder)

0° (with cut sheet feeder)

Technical Specifications 8-7

Interface Specifications

Your printer is equipped with an S-bit parallel interface. For specifications on optional interfaces, refer to their manuals.

Pin Assignments for the Parallel Interface

Connector pin assignments and a description of their respective interface signals are shown in the following table.

2

3

4

5

6

7

8

9

10

Signal Return

Pin Pin

Signal Direction Description

1

19 STROBE IN

STROBE pulse to read data. Pulse width must be more than 0.5 microseconds at the receiving terminal.

11

12

20

21

22

23

24

25

26

27

28

29

DATA 1

DATA 2

DATA 3

DATA 4

DATA 5

DATA 6

DATA 7

DATA 8

ACKNLG

BUSY

30 PE

IN

IN

IN

IN

IN

IN

IN

IN

OUT

OUT

OUT

These signals represent information of the

1st to 8th bits of parallel data, respectively. Each signal is at HIGH level when data is logical 1 and LOW when it is logical 0.

About an 11-microsecond pulse. LOW indicates that data has been received and that the printer

IS ready to accept more data.

A HIGH signal indicates that the printer cannot receive data. The signal goes

HIGH in the following cases:

1) During data entry (ea. char. time)

2) During printing

3) When off line

4) During printer-error state

A HIGH signal indicates that the printer is out of paper.

8-8

Technical Specifications

Interface Specifications

Signal Return

Pin

Pin

Signal Direction Description

13

SLCT OUT

Pulled up to + 5 volts through 3.3 Kohm resistance.

14

AUTO

FEED

XT

IN

When this signal is LOW, the paper is automatically fed 1 line after printing. (The

Signal level can be fixed to this by setting

DIP switch 2-4 to on.)

15 NC Not used.

16

17

18

19-30

31 16

GND

CHASSIS

GND

NC

GND

INIT

IN

Logic ground level.

Printer's chassis ground, which is isolated from the logic ground.

Not used.

Twisted-pair return signal ground level.

When this level becomes LOW, the printer controller is reset to its power-up state and the print buffer is cleared. This level is normally HIGH; its pulse width must be more than 50 microseconds at the receiving terminal.

32 ERROR OUT

33 GND

34 NC

35

36

OUT

SLCT IN IN

This level becomes LOW when the printer is:

1) in paper out state.

2) off line.

3) in error state.

Same as for Pins 19-30

Not used

Pulled up to 5V through 3.3 Kohm resistance.

The DC1/DC3 code is valid only when this signal is HIGH. (Internal fixing can be carried out with Jumper J10. The level of this signal is factory-set to LOW.)

Technical Specifications 8-9

Interface Specifications

l l l l

The column heading “Direction” refers to the direction of signal flow as viewed from the printer.

“Return” denotes the twisted-pair return, to be connected at signal ground level. For the interface wiring, be sure to use a twisted-pair cable for each signal and to complete the connection on the return side. These cables should be shielded and connected to the chassis of the host computer and the printer.

All interface conditions are based on TTL level. Both the rise and the fall times of each signal must be less than 0.2 microseconds.

Data transfer must be carried out by observing the ACKNLG or

BUSY signal. Data transfer to this printer can be carried out only after receipt of the ACKNLG signal or when the level of the BUSY signal is LOW.

Interface Timing

The figure below shows the timing for the parallel interface.

8-10

Technical Specifications

Interface Specifications

Printing Enabled/Disabled Signals and Control Conditions

The table below shows the relationship between printing being enabled or disabled, the on line/off line status, and the receipt of the data on/off control characters, DC1 or DC3.

ON LINE SLCT IN

DC1/DC3

ERROR

BUSY

(Indicator on)

(Data on/off control) on line Low (J1

DC1/DC3

High interface)

(no effect)

High/Low

ACKNLG

Pulsed ea. char.

Printing

(Disabled/ enabled)

Enabled

(normal cond.) on line

High

DC1

Recv'd

High High/Low

Pulsed ea. char.

Enabled on line

High

DC3

Recv'd

High High/Low

Pulsed ea. char.

Disabled* off line

High/Low DC1/DC3

(no effect) (no effect)

Low

High

Not generated

Disabled

*While printing is disabled, character data is being received and acknowledged so that the printer can look for another DC1 character, which would allow it to resume printing.

Technical Specifications

8-11

Option Specifications

Single-bin Cut Sheet Feeder (Optional)

Dimensions and weight: 24.3 in (W) x

17.4

in (D) x

16.4

in (H)

(618

mm (W) x

443

mm (D) x

416

mm (H))

(mounted on the printer) approx.

5.9

lb

(2.7

kg)

Bin capacity:

Single sheet : Up to 150 sheets of 22 lb

Up to 185 sheets of 17 lb

Up to 100 sheets of 24 lb

(Total thickness should not exceed

9/32

inches or

15

mm)

Stacker capacity:

Single sheet: Up to

80

sheets of

22

lb

Up to 100 sheets of

17

lb

Up to 50 sheets of

24

lb

MCBF:

100,000

cycles

Environmental condition:

Temperature

Operation:

Storage:

40°F

to 95°F (5°C to 35°C) for up to

22

lb paper and

59°F

to 95°F (15°C to 25°C) for heavier paper

-22°F to 140°F (-30°C to

60°C)

Humidity

Operation:

Storage:

15%

to 80% (noncondensing) for up to

22

lb paper and

30%

to 60% (noncondensing) for heavier paper

5% to 85% (noncondensing)

8-12

Technical Specifications

Option Specifications

Paper:

Width

Length

7.17

to 14.33 inches

(182

to

364

mm)

10.12 to 14.33 inches

(257

to 364 mm)

Thickness

Weight

Printable area

0.0028 to 0.0055

inches

(0.07

to

0.14

mm)

17

lb to 24 lb

0.12 inches (3 mm) or more

0.33 inches (8.5 mm) or more

0.12 inches (3 mm)

or more

0.53 inches (13.5 mm) or more

Paper feed accuracy cannot be assured within 0.9" (22 mm) from either the top or bottom edges of the paper.

Storage condition:

Temperature 65°F to 70°F

(18°C to 22°C)

Humidity

40% to 60%

Technical Specifications

8-13

Initialization

There are two ways that the printer can be initialized (returned to the default settings) through the hardware and one way through the software. These are described in the following table:

Hardware initialization

Software initialization l

The power is turned on.

l

The printer receives an INIT signal at the parallel interface (pin 31 goes LOW).

l

The software sends the ESC @ (initialize the minter) command.

Default Settings

The table below shows the default conditions that become valid when the printer is initialized.

Item

Top of form position

Left and right margins

Line spacing

Vertical tab position

Horizontal tab positions

VFU channel

Font selection

Condensed mode

Character spacing

Justification

Special printing effects

Graphic mode assignment

Reset to:

Current paper position

Cancelled

1/6-inch line spacing

Cleared

Every eight characters

Channel 0

Hardware: The current DIP switch setting

Software: The current SelecType setting

Hardware: The current DIP switch setting

Software: The current SelecType setting

The current DIP switch setting

Left justification

Cancelled (except condensed printing)

ESC K = ESC * 0, ESC L = ESC * 1,

ESC Y = ESC * 2, ESC Z = ESC * 3

8-14

Technical Specifications

Initialization

Also, the data buffer is cleared when the printer is initialized by turning on the power or by an INIT signal.

Note: The user-defined character set is not cleared when the printer is initialized with the software command (ESC @).

Technical Specifications

8-15

Chapter 9

Command Summary

Using the Command Summary . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

Control Key Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4

Commands in Numerical Order .................................................. 9-5

Commands Arranged by Topic . . . . . . . . . . . . . . . . . . . . . . . . . 9-8

Printer Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8

MSB Control ..................................................................... 9-11

Data Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12

Vertical Motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13

Horizontal Motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19

Overall Printing Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22

Print Size and Character Width . . . . . . . . . . . . . . . . . . . . . . 9-24

Print Enhancement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-28

Word Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-33

Character Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-34

User-defined Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-36

Graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-38

Command Summary 9-1

Using the Command Summary

This chapter lists and describes all the commands available on the

LQ-1010.

The first part of this chapter lists all commands in numerical order and gives the number of the page where each is fully described. If you know which command you are looking for, consult the numerical list.

Note: The Quick Reference card at the end of the book also contains a list of the commands divided by topic, with page number references that direct you to full explanations of the commands.

The second part of this chapter lists and describes each command separately; the commands are divided into the following subjects:

Printer operation

MSB control

Data control

Vertical motion

Horizontal motion

Overall printing style

Print size and character width

Print enhancement

Word processing

Character sets

User-defined characters

Graphics

Each command description has a format section and a comment section. The format section gives the ASCII, decimal, and hexadecimal values for the command. These three formats are equivalent, and it should be easy to pick the one most suited to your purpose. The comment section describes the effect of the command and gives any additional information necessary for using it.

Note: Some application programs use control key sequences. See the

Control Key chart on page 9-4.

9-2 Command Summary

Using the Command Summary

The simplest type of command consists of a single character to be sent to the printer. For instance, to print in condensed mode, the code format is:

A S C I I c o d e : S I

Decimal: 15

Hexadecimal: OF

This code can be sent from a program by sending the code 15 directly.

More complex commands consist of two or more character codes. For example, to print in double-wide mode, the code format is the following:

ASCII code:

Decimal:

ESC W n

27 87

n

Hexadecimal:

1B 57

n

In this case n can be either

1

(on) or 0 (off), to begin or end double-wide printing. You can use either of the following commands to turn on double-wide print from BASIC:

LPRINT CHR$(27);CHR$(87);CHR$(1)

LPRINT CHR$(27);"W";CHR$(l)

For the following commands that use only 0 or 1 for the variable, either the decimal or hexadecimal values

1 and 0 or the ASCII characters 1 and 0 can be used:

ESC U, ESC x, ESC p, ESC W, ESC S, ESC-, and ESC %

For example, in BASIC you can turn on proportional spacing with either of these statements:

LPRINT CHR$(27);“p”;CHR$(1)

LPRINT CHR$(27);“p”;“1”

Command Summary 9-3

Using the Command Summary

Dec.

10

11

12

13

7

8

9

3

4

5

6

1

0

2

Control Key Chart

Some application programs use control key codes for decimal values

O-27. The table below gives you the proper values. The Control Key column indicates that you press the control key at the same time you press the key for the letter or symbol in that column. For example, you press the control key and A at the same time to send the value 1.

Some application programs that use this system cannot use Control-@, and many programs use the control keys for other purposes.

Hex.

03

04

05

06

07

08

09

00

01

02

OA

OB

OC

OD

Ctrl. Key

@

A

F

G

H

I

J

K

B

C

D

E

L

M

Dec.

20

21

22

23

24

25

26

27

14

15

16

17

18

19

Hex.

13

14

15

16

17

OE

OF

10

11

12

18

19

1A

1B

Ctrl. Key

S

T

Q

R

U

V w

X

Y

Z

N

O

P

[

9-4

Command Summary

Commands in Numerical Order

The following list shows control codes and ESC sequences with their decimal and hexadecimal values, and the page where the description of the command can be found.

ASCII Dec.

Hex.

Description

BEL

BS

HT

LF

V T

FF

CR

S O

SI

DC1

DC2

DC3

DC4

CAN

DEL

ESC SO

ESC SI

ESC EM

ESC SP

ESC !

ESC #

ESC $

ESC %

ESC &

ESC ( -

7

8

15

24

07

08

9 09

10 0A

11

0 B

12 0C

13

0 D

14 0E

0 F

17

1 1

18 12

19 13

20 14

1 8

127 7F

14

0 E

15 0F

25 19

32 20

33 21

35 23

36 24

37 25

38 26

40 28

Page

Beeper . . . . . . . . . . . . . . . . . . . . . .

9-12

Backspace . . . . . . . . . . . . . . . . . . .

9-20

Tab Horizontally . . . . . . . . . . . . .

9-21

Line Feed . . . . . . . . . . . . . . . . . . . .

9-14

Tab Vertically . . . . . . . . . . . . . . . .

9-17

Form Feed . . . . . . . . . . . . . . . . . . .

9-13

Carriage Return . . . . . . . . . . . . . .

9-12

Select Double-wide Mode

(one line) . . . . . . . . . . . . . . . . . . . .

Select Condensed Mode . . . . . . .

9-26

9-25

Select Printer . . . . . . . . . . . . . . . . .

9-8

Cancel Condensed Mode . . . . . . .

9-26

Deselect Printer . . . . . . . . . . . . . . .

9-9

Cancel Double-wide Mode

(one line) . . . . . . . . . . . . . . . . . . . .

Cancel Line . . . . . . . . . . . . . . . . . .

9-27

9-12

Delete Character . . . . . . . . . . . . . .

9-9

Select Double-wide Mode

(one line) . . . . . . . . . . . . . . . . . . . .

9-27

Select Condensed Mode . . . . . . .

9-26

Control Cut Sheet Feeder . . . . . .

9-10

Set Intercharacter Space . . . . . . .

9-33

Master Select . . . . . . . . . . . . . . . .

9-23

Cancel MSB Control . . . . . . . . . .

9-11

Set Absolute Print Position . . . . .

9-20

Select User-defined Set . . . . . . . . .

9-37

Define User-defined Characters . 9-36

Select Score . . . . . . . . . . . . . . . . . .

9-31

Command Summary 9-5

ASCII

ESC *

ESC +

ESC -

ESC /

ESC 0

ESC 2

ESC 3

ESC 4

ESC 5

ESC 6

ESC 7

ESC :

ESC <

ESC =

ESC >

ESC ?

ESC @

ESC A

ESC B

ESC C

ESC C 0

ESC D

ESC E

ESC F

ESC G

ESC H

ESC J

ESC K

ESC L

ESC M

Commands in Numerical Order

61 3D

62 3E

63 3F

64 40

65 41

66 42

67 43

67 43

68 44

69 45

70 46

71 47

72 48

74 4A

75 4B

Dec.

Hex.

Description

42 2A

43 2B

45 2D

47 2F

48 30

50 32

51 33

52 34

53 35

54 36

55 37

58 3A

60 3C

76 4C

77 4D

Page

Select Graphics Mode .......................... 9-39

Set n/360-inch Line Spacing .............. 9-15

Turn Underline Mode

On/Off ................................................

9-32

Select Vertical Tab Channel ................ 9-18

Select 1/B-inch Line Spacing ............

9-15

Select 1/6-inch Line Spacing ........... 9-15

Set n/180-inch Line Spacing ............ 9-16

Select Italic Mode ........................

9-34

Cancel Italic Mode ...........................

9-35

Enable Printable Characters ..............

9-37

Enable Upper Control Codes ........... 9-37

Copy ROM to RAM ..........................

9-36

Select Unidirectional Mode

(one line) .........................................

9-9

Set MSB to 0 ......................................

9-11

Set MSB to 1 ......................................

9-11

Reassign Graphics Mode ................... 9-40

Initialize Printer ........................................

9-8

Set n/60-inch Line Spacing ...............

9-16

Set Vertical Tabs .................................

9-17

Set Page Length in Lines .................. 9-13

Set Page Length in Inches ................

9-13

Set Horizontal Tabs ..........................

9-22

Select Emphasized Mode ................... 9-28

Cancel Emphasized Mode ...............

9-28

Select Double-strike Mode .............

9-29

Cancel Double-strike Mode ............

9-29

Perform n/180-inch Line Feed ...

9-16

Select Single-density Graphics

Mode ...................................................

9-38

Select Double-density Graphics

Mode ...................................................

9-38

Select 12 CPI ......................................

9-24

9-6

Command Summary

ASCII

ESC N

ESC 0

ESC P

ESC Q

ESC R

ESC S 0

ESC S 1

ESC T

ESC U

ESC

W

ESC Y

ESC Z

ESC \

ESC a

ESC b

ESC g

ESC k

ESC l

ESC p

ESC q

ESC t

ESC w

ESC x

Commands in Numerical Order

Dec.

Hex.

Description

78 4E

79 4F

80 50

81 51

82 52

83 53

83 53

84 54

85 55

87 57

89 59

90 5A

92 5C

97 61

98 62

103 67

107 6B

108 6C

112 70

113 71

116 74

119 77

120 78

Page

Set Skip Over Perforation . . . . . .

9-14

Cancel

Skip Over Perforation . . .

9-14

Select 10 CPI . . . . . . . . . . . . . . . . .

9-24

Set Right Margin . . . . . . . . . . . . .

9-19

Select an International

Character Set . . . . . . . . . . . . . . . .

9-35

Select Superscript Mode . . . . . . .

9-29

Select Subscript Mode . . . . . . . . .

9-30

Cancel Superscript/Subscript

Mode . . . . . . . . . . . . . . . . . . . . . . .

9-30

Turn Unidirectional Mode

On/Off . . . . . . . . . . . . . . . . . . . . .

9-10

Turn Double-wide Mode

On/Off . . . . . . . . . . . . . . . . . . . . .

9-27

Select High-speed

Double-density

Graphics Mode . . . . . . . . . . . . . . .

9-38

Select Quadruple-density

Graphics Mode . . . . . . . . . . . . . . . .

9-39

Set Relative Print Position . . . . . .

9-21

Select Justification . . . . . . . . . . . .

9-33

Set Vertical Tabs in Channels . . .

9-18

Select 15 CPI . . . . . . . . . . . . . . . . .

9-24

Select Typestyle Family . . . . . . . .

9-23

Set Left Margin . . . . . . . . . . . . . . .

9-19

Turn Proportional Mode

On/Off . . . . . . . . . . . . . . . . . . . . .

9-25

Select Character Style . . . . . . . . .

9-32

Select Character Table . . . . . . . . .

9-34

Turn Double-high Mode

On/Off . . . . . . . . . . . . . . . . . . . . .

9-28

Select Letter Quality or Draft . . .

9-22

Command Summary 9-7

Commands Arranged by Topic

This following section lists and describes all the commands by topic.

See the Quick Reference card at the back of this book for a handy list of commands by topic.

Printer Operation

ESC @

Format:

ASCII code:

Decimal:

Hexadecimal :

ESC @

27 64

1B 40

Initialize Printer

Comments:

Resets the printer mode and clears the current print line preceding the command.

DC1

Format:

ASCII code:

Decimal :

Hexadecimal :

DC1

17

11

Select Printer

Comments:

Returns the printer to the selected state if it has been deselected by the printer deselect code (DC3). It does not select the printer if it has been switched off line by the ON LINE button.

9-8

Command Summary

Commands Arranged by Topic

DC3

Format:

ASCII code:

Decimal:

Hexadecimal:

DC3

19

13

Deselect Printer

Comments:

Puts the printer into the deselected state until the select printer code

(DC1)

is received. The printer cannot be reselected with the ON LINE button.

DEL

Format:

ASCII code:

Decimal:

Hexadecimal:

DEL

127

7F

Delete Character

Comments:

Removes the last text character on the print line but does not affect control codes.

ESC <

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC <

27 60

1B 3C

Select Unidirectional Mode (one line)

Comments:

Text printing is normally bidirectional. (Graphics printing is always unidirectional.) This command selects unidirectional printing for one line only. (It is cancelled by a carriage return.) The print head moves to the extreme left (home) position and printing takes place from left to right.

Command Summary 9-9

Command Summary

ESC U

Format:

ASCII code:

Decimal:

ESC U n

27 85 n

Hexadecimal:

1B 55 n

Turn Unidirectional Mode On/Off

Comments:

The following values can be used for n:

1: Turns the mode on

0: Turns the mode off

Text printing is normally bidirectional. (Graphics printing is always unidirectional.) This command moves the print head to the extreme left (home) position; printing takes place from left to right. When this mode is off and DIP switch 2-6 is on, multi-pass characters are printed bi-directionally.

ESC EM

Format:

ASCII code:

Decimal:

ESC EM n

27 25 n

Hexadecimal: 1B 19 n

Control Cut Sheet Feeder

Comments:

The following values can be used for n:

0: Turns mode off

4: Turns mode on

R: Ejects a sheet. (No paper is loaded.)

The command should not be used unless the cut sheet feeder is installed. It is ignored if any value other than 0, 4, or R is used for n.

The cut sheet feeder mode can also be turned on and off by setting

DIP switch 1-8.

9-10

Command Summary

Commands Arranged by Topic

MSB Control

MSB means the Most Significant Bit. MSB control (ESC = ,

ESC > , and ESC #) does not work for graphics or user-defined characters.

ESC =

Format:

ASCII code:

Decimal :

Hexadecimal:

ESC =

27 61

1B 3D

Set MSB

to

0

Comments:

Sets the MSB of all incoming data to 0. Some computers always send data

with

the MSB set to

1,

which means that italics or character graphics are always printed. ESC = can overcome this problem.

Set MSB to

1

ESC >

Format:

ASCII

code:

Decimal:

Hexadecimal:

ESC >

27 62

1B 3E

Comments:

Sets the MSB bit of all incoming data as 1.

ESC #

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC #

27 35

1B 23

Cancel MSB Control

Comments:

Cancels the MSB control set by ESC = or ESC > .

Command Summary

9-11

Commands Arranged by Topic

BEL

Format :

ASCII code:

Decimal:

Hexadecimal:

BEL

7

07

Comments:

Sounds the printer’s beeper.

Beeper

Data Control

CR

Format:

ASCII code:

Decimal:

CR

13

H e x a d e c i m a l : 0 D

Carriage Return

Comments:

Prints the data in the print buffer and returns the print position to the left margin. A line feed is added if the AUTO FEED XT line on the parallel interface is held LOW.

CAN

Format:

ASCII code:

Decimal:

Hexadecimal:

CAN

24

18

Cancel Line

Comments:

Clears all text on the print line, but does not affect control codes.

9-12

Command Summary

Commands Arranged by Topic

Vertical

Motion

FF

Format:

ASCII code:

Decimal:

Hexadecimal:

FF

12

0C

Form Feed

Comments:

Prints the data in the print buffer and advances the paper to the top of the next form according to the current page length. When using a cut sheet feeder, FF ejects the sheet into the stacker.

ESC C

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC C n

27 67 n

1B 43 n

Set Page Length in Lines

Comments:

Sets the page length to n lines in the current line spacing. The value of n must be from

1

to

127

lines. The top of form position is reset to the current line.

Overrides the DIP switch page length setting.

ESC C 0

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC C 0 n

27

1B

67

43

0

00

n n

Set Page Length in Inches

Comments:

Sets the page length to n inches. The value of n must be from

The top of form position is reset to the current line.

1

to

22.

Overrides the DIP switch page length setting.

Command Summary

9-13

Commands Arranged by Topic

ESC N

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC N n

27 78

n

1B 4E n

Set Skip Over Perforation

Comments:

The variable n is

the

number of lines skipped between

the

last line printed on one page and the first line to print on the next page. For example, with

the

standard setting for line spacing (l/6-inch), and page length (66 lines), ESC N 6 prints 60 lines and

then

skips 6. This setting is cancelled by ESC O,

ESC

C, or

ESC

C 0. The value of

n

must be from 1 to 127.

Overrides the DIP switch setting for 1-inch skip over perforation.

ESC O

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC O

27 79

1B 4F

Cancel Skip Over Perforation

Comments:

Cancels

the skip over perforation set by ESC N. Overrides the DIP switch setting for 1-inch skip over perforation.

LF

Format:

ASCII code:

Decimal:

LF

10

H e x a d e c i m a l : O A

Line Feed

Comments:

When this command is received,

the

data in

the

print buffer is printed and the paper advances one line in the current line spacing.

9-14

Command Summary

Commands Arranged by Topic

ESC 0

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC 0

27 48

1B 30

Select l/8-inch Line Spacing

Comments:

Sets

the

line

spacing to

1/8

of an inch for subsequent line feed commands. The 0 is the digit zero and not ASCII code 0.

ESC 2

Format:

ASCII code:

D e c i m a l :

Hexadecimal:

ESC 2

27 50

1B 32

Select 1/6-inch Line Spacing

Comments:

Sets the line spacing to 1/6 of an inch for subsequent line feed commands. The 2 is the digit two and not ASCII code 2. This line spacing is the default at power on.

ESC +

Format:

ASCII code:

Decimal:

Hexadecimal :

ESC + n

27 43 n

1B 2B

n

Set n/360-inch Line Spacing

Comments:

Sets line spacing to n/360 of an inch for subsequent line feed commands. The value of n must be from 0 to 255.

Command Summary

9-15

Commands Arranged by Topic

ESC 3

Format:

ASCII code:

Decimal :

Hexadecimal :

ESC 3 n

27 51

1B 33

n

n

Set n/MO-inch Line Spacing

Comments:

Sets the line spacing to n/180 of an inch for subsequent line feed commands. The 3 is the digit three and not ASCII code 3. The value of n must be from 0 to 255.

ESC A

Format:

ASCII code:

Decimal:

Hexadecimal :

ESC A n

27 65 n

1B 41 n

Set n/60-inch Line Spacing

Comments:

Sets the line spacing to n/60 of an inch for subsequent line feed commands. The value of n must be from 0 to 85.

ESC J

Format:

ASCII code:

Decimal :

ESC J n

27 74 n

Hexadecimal: 1B 4A n

Perform n/180-inch Line Feed

Comments:

Advances the paper n/180 of an inch. The value of n must be from 0 to 255. This command produces an immediate line feed but does not affect subsequent line spacing and does not produce a carriage return.

9-16 Command Summary

Commands Arranged by Topic

VT

Format:

ASCII code:

Decimal:

V T

11

H e x a d e c i m a l : 0 B

Tab Vertically

Comments:

Advances the paper to the next vertical tab position in the channel selected by ESC /. If no channel has been selected, channel 0 is used.,

If no vertical tabs have been set, the paper advances one line.

ESC B

Format:

ASCII code:

Decimal :

Hexadecimal:

Set Vertical Tabs

ESC B n1 n2… 0

27 66

n1 n2 … 0

1B 42 nl

n2 … 00

Comments:

Sets up to

16

vertical tabs in the current line spacing. Tab settings are not affected by subsequent changes in line spacing. The tab settings are entered as n1, n2, etc.-all from

1

to 225, in ascending order. The

0 value (null) indicates the end of the command. All settings are stored in channel 0 (see ESC b). ESC B 0 clears the tab settings,

Command Summary

9-17

Commands Arranged by Topic

ESC b

Format:

ASCII code:

Decimal:

Hexadecimal:

Set Vertical Tabs in Channels

ESC b c n1 n2 …. 0

27 98 c n1 n2 …

0

1B

62 c n1 n2 … 00

Comments:

Functions the same as ESC B, except that the variable c selects a channel for the vertical tabs, which must be from 0 to 7. Therefore, up to eight sets of vertical tabs can be set. The channels are selected by ESC /. To clear the tabs in channel c, use ESC b c 0.

ESC /

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC / c

27 47 c

1B 2F c

Select Vertical Tab Channel

Comments:

This command is used to select the vertical tab channel, with the value of c from 0 to 7. All subsequent VT commands use the channel selected by this command. If no channel has been selected, channel 0 is used.

9-18

Command Summary

Commands Arranged by Topic

Horizontal Motion

ESC 1

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC 1 n

27

108 n

1B 6C n

Set Left Margin

Comments:

Sets the left margin to n columns in the current character size.

Settings made in the proportional mode are treated as

10

cpi. This command clears previous tab settings and all previous characters in the print line. Use lowercase 1 (as in left), not the numeral one. The minimum space between the margins is the width of one double-wide

10 cpi character.

ESC Q

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC Q n

27 81 n

1B

51 n

Set Right Margin

Comments:

Sets the right margin to n columns in the current character size.

Settings made in the proportional mode are treated as

10

cpi. This command clears previous tab settings and all previous characters in the print line. The minimum space between the margins is the width of one double-wide

10

cpi character.

Command Summary

9-19

Commands Arranged by Topic

BS

Format:

ASCII code:

Decimal:

Hexadecimal:

BS

8

08

Backspace

Comments:

Prints out data in the print buffer, then moves the print position one space to the left. Backspacing is possible up to, but not beyond, the left margin setting. The BS code is ignored if ESC a2 or ESC a3 has been sent.

ESC $

Format:

ASCII code:

Decimal :

Hexadecimal:

Set Absolute Print Position

ESC $ n1 n2

27 36 n1 n2

1B 24 n1 n2

Comments:

This sequence specifies the distance from the current left margin that subsequent characters are to be printed, using this formula: total number of dots = n1 + (n2 x 256). Each unit equals 1/60th of an inch. The sequence is ignored and the previous setting remains effective if the position specified is beyond the right margin.

9-20

Command Summary

Commands Arranged by Topic

ESC \

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC \ n1 n2

27 92 n1 n2

1B 5C n1 n2

Set Relative Print Position

Comments:

Determines the position (relative to the current position) at which printing of subsequent data will start. To find n1 and n2, first calculate the displacement required in dots. If the displacement is to the left, subtract it from 65536. Send the resulting number using this formula: total number of dots = n1 + (n2 x 256). The command is ignored if it would move the print position outside the current margins. A unit is 1/120th of an inch in draft, and 1/180th of an inch in Letter Quality or proportional modes.

HT

Format:

ASCII code:

Decimal:

Hexadecimal:

HT

9

09

Tab Horizontally

Comments:

Advances the print position to the next horizontal tab setting. The default tabs are at-a-character intervals in the currently set pitch. Tab positions are not affected by subsequent changes in cpi.

Command Summary

9-21

Commands Arranged by Topic

ESC D

Format:

ASCII code:

Decimal:

Hexadecimal:

Set Horizontal Tabs

ESC D n1 n2 … 0

27 68

n1 n2 …

0

1B

44

n1 n2 … 00

Comments:

This command allows setting of up to 32 horizontal tabs, which are entered as n1, n2, n3, etc. (from 1 to 255) with the number 0 terminating the command. The tab settings must be entered in ascending order. ESC D 0 clears all tabs. The default settings, when power is turned on or after an ESC @ command, are at every eight characters. The tab settings are not affected by changes in cpi. The tab positions in proportional printing are determined by the

10

cpi character size.

Overall Printing Style

ESC x

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC x n

27 120 n

1B 78 n

Comments:

The following values can be used for n:

0: Selects draft mode.

1: Selects Letter Quality (LQ) mode.

Overrides the SelecType panel setting.

Select Letter Quality or Draft

9-22

Command Summary

Commands Arranged by Topic

ESC k

Format:

ASCII code:

Decimal:

Hexadecimal :

ESC k n

27 107

n

1B 6B n

Select Typestyle Family

Comments:

This command affects only the Letter Quality typestyle, not draft. If n = 0, the Roman font is used. To select one of the other typestyles, use the family number of the font

as

shown below. For example, to choose the Prestige font, use 3 for the value of n. The following values can be used for n:

0: Roman

1: Sans Serif

2: Courier

3: Prestige

4:

Script

5:

OCR-B

6:

OCR-A

7: Orator

8: Orator-S

Typestyle families 2 to 8 are available only if the appropriate font module is installed, such as the Multi-Font Module.

Overrides the SelecType panel setting and DIP switch font setting.

ESC !

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC ! n

27 33

n

1B

21

n

Master Select

Comments:

Selects any valid combination of the following modes: 10 cpi,

12

cpi, proportional, condensed, emphasized, double-strike, double-wide, italic, and underline. For details on how to set n, see the Selecting

Typestyles With Master Select section in Chapter 4.

Command Summary 9-23

Commands Arranged by Topic

Print Size and Character Width

ESC P

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC P

27 80

1B 50

Select 10 CPI

Comments:

Selects 10 character per inch printing. This command is normally used to cancel 12 or 15 cpi.

ESC M

Format :

ASCII code:

Decimal:

Hexadecimal:

ESC M

27 77

1B 4D

Comments:

Selects 12 character per inch printing.

Select 12 CPI

ESC g

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC g

27 103

1B 67

Select 15 CPI

Comments:

Selects 15 character per inch printing, and cancels 10 or 12 cpi.

Cannot be combined with condensed mode.

9-24 Command Summary

Commands Arranged by Topic

ESC p

Turn Proportional Mode On/Off

Format:

ASCII code:

Decimal:

ESC

27 p n

112 n

Hexadecimal: 1B 70 n

Comments:

Turns proportional mode on and off.

The following values can be used for n:

1: Turns mode on.

0: Turns mode off.

The width of proportional characters varies from character to character. Therefore, a narrow letter like i receives less space than a wide letter like W. Proportional character widths are given in the Appendix. This command overrides fixed cpi fonts. When proportional is cancelled, the previously selected font is used.

Graphic characters are printed in fixed cpi only; proportional mode is only available in Roman and Sans Serif fonts.

SI

Format:

ASCII code:

Decimal:

SI

15

Hexadecimal: OF

Select Condensed Mode

Comments:

Prints characters at about 60 percent of their normal width. For example, the condensed 10 cpi mode has 17 characters per inch.

Condensed mode cannot be combined with 15 cpi. Condensed can be turned on and off by SelecType, the SI command, or DIP switch 1-6.

Command Summary

9-25

Commands Arranged by Topic

ESC SI

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC SI

27 15

1B OF

Select Condensed Mode

Comments:

Duplicates the SI command and the function of the CONDENSED button on the control panel.

DC2

Format:

ASCII code:

Decimal:

Hexadecimal:

DC2

18

12

Cancel Condensed Mode

Comments:

Cancels condensed mode set by SI, ESC SI, or SelecType and returns printing to normal.

S O

Format:

ASCII code:

Decimal:

Hexadecimal: s o

14

OE

Select Double-wide Mode (one line)

Comments:

Doubles the width of all characters on one line. This mode is cancelled by LF, FE VT, or DC4.

9-26 Command Summary

ESC SO

Format:

ASCII

code:

Decimal:

Hexadecimal:

E S C S O

27 14

1B

O E

Comments:

Duplicates the SO command.

Commands Arranged by Topic

Select Double-wide Mode (one line)

ESC W

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC W n

27 87 n

1B

57 n

Turn Double-wide Mode On/Off

Comments:

Doubles

the

width of all characters.

The following values can be used for n:

1: Turns mode on.

0: Turns mode off.

DC4

Format:

ASCII code:

Decimal :

Hexadecimal:

DC4

20

14

Cancel Double-wide Mode (one line)

Comments:

Cancels double-wide mode selected by SO or ESC SO, but not double-wide mode selected by ESC W or ESC !.

Command Summary

9-27

Commands Arranged by Topic

ESC w

Format:

ASCII code:

Decimal:

Hexadecimal:

Turn Double-high Mode On/Off

ESC w n

27 119 n

1B 77 n

Comments:

Doubles the height of

all

characters.

The following values can be used for n:

1: Turns mode on.

0: Turns mode off.

Cannot be used with the pull tractor.

Print Enhancement

ESC E

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC E

27 69

1B 45

Select Emphasized Mode

Comments:

Makes text bolder by printing each dot twice, with the second dot printed slightly to the right of the first.

ESC F

Format:

ASCII code:

Decimal :

Hexadecimal:

ESC F

27 70

1B 46

Cancel Emphasized Mode

Comments:

Cancels the emphasized mode selected by ESC E.

9-28 Command Summary

Commands Arranged by Topic

ESC G

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC G

27 71

1B 47

Select Double-strike Mode

Comments:

Makes text bolder by printing each line twice.

ESC H

Format :

ASCII code:

Decimal:

ESC H

27 72

Hexadecimal: 1B 48

Cancel Double-strike Mode

Comments:

Cancels the double-strike mode selected by ESC G.

ESC S0

Format:

ASCII

code:

Decimal:

Hexadecimal:

ESC S 0

27

1B

83

53

0

00

Select Superscript Mode

Comments:

Prints characters about two-thirds of the normal character height in the upper part of the character space.

Command Summary

9-29

Commands Arranged by Topic

ESC S 1

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC S 1

27 83

1B 53

1

01

Select Subscript Mode

Comments:

Prints characters about two-thirds of the normal character height in the lower part of the character space.

ESC T

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC T

27 84

1B 54

Cancel Superscript/Subscript Mode

Comments:

Cancels either superscript or subscript.

9-30

Command Summary

Commands Arranged by Topic

ESC ( -

Format:

ASCII code:

Decimal:

Hexadecimal:

Select Score

ESC ( - n1 n2 m d1 d2

27 40 45

n1 n2

m d1 d2

1B 28

2D n1 n2

m d1 d2

Comments:

Use decimal or hexadecimal values for all variables, not ASCII characters.

Use the following values for the first

3

variables: n1 must be 3.

n2 must be 0.

m

must be 1.

The value of

d1

determines the location of the score:

d1

= 1 for underline.

d1

= 2 for strike-through.

d1 = 3

for overscore.

The value of d2 determines whether the score line is single, double, broken, or continuous: d2 = 0 Cancel the score line selected by

d1.

d2

=

1

Single continuous line.

d2 =

d2

=

2

5

Double continuous line.

Single broken line.

d2 = 6 Double broken line.

Command Summary

9-31

Commands Arranged by Topic

ESC -

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC - n

27 45 n

1B 2D

n

Turn Underline Mode On/Off

Comments:

This mode provides continuous underlining including spaces.

The following values can be used for n:

1: Turns mode on.

0: Turns mode off.

Areas skipped with HT or ESC $ are not underlined.

ESC

q

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC q n

27 113 n

1B 71 n

Comments:

The following values can be used for

0: Selects normal.

n:

1: Selects outline.

2: Selects shadow.

3: Selects outline with shadow.

Select Character Style

This command is valid for all characters, with the exception of character codes B0H to DFH, F4H, and F5H (176 to 223, 244, and

245 decimal)

in the Epson Extended Graphics character table.

9-32

Command Summary

Commands Arranged by Topic

Word Processing

ESC a

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC a n

27 97 n

1B 61 n

Select Justification

Comments:

Sets the type of justification.

The following values can be used for n:

0: Selects left justification.

1: Selects centering.

2: Selects right justification.

3: Selects full justification.

The default setting is n = 0. Full justification (n = 3) is performed

when

the buffer becomes full; HT and BS are invalid except in n = 0 mode. For n = 3 there must be no carriage returns within a paragraph.

ESC SP (space)

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC SP n

27 32

n

1B 20 n

Set Intercharacter Space

Comments:

Sets the amount

of

space added to

the

right of

each

character, in addition to the space already allowed in

the

design of the character.

The number of dots is determined by n, which should be from 0 to

127. Each unit of space is 1/120th of an inch in draft mode and

1/180th of an inch in Letter Quality and proportional modes.

Command Summary 9-33

Commands Arranged by Topic

Character Tables

ESC t

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC t n

27 116 n

1B

74 n

Select Character Table

Comments:

Selects the character table used by codes

128

to

255.

Selecting Epson

Extended Graphics characters does not disable italic printing. Italic printing can still be selected by ESC

4.

The following values can be used for n:

0: Selects italics character table.

1:

Selects Epson Extended Graphics character table.

2:

Selects user-defined character table and remaps user-defined

O-127

to

128-255.

Overrides the function of DIP switch

1-7.

must equal 00 hex, 01 hex, or 02 hex.

Note that the value of n

ESC

4

Format:

ASCII code:

Decimal:

ESC

4

27 52

Hexadecimal: 1B 34

Select Italic Mode

Comments:

Causes characters from the italic character table to be printed. This command is valid even if the Epson Extended Graphics character set has been selected by ESC t or by DIP switch 1-7, but the character graphics are not italicized.

9-34 Command Summary

Commands Arranged by Topic

Cancel Italic Mode

ESC

5

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC 5

27 53

1B 35

Comments:

Cancels the mode selected by ESC 4.

ESC R

Format:

ASCII code:

Decimal:

Hexadecimal:

Select an International Character Set

ESC R n

27 82 n

1B 52 n

Comments:

Selects one of the international character sets.

The following values can be used for n:

0 = USA

1

= France

2 = Germany

8 = Japan

9

= Norway

10

= Denmark II

3 = England

4 = Denmark I

5

= Sweden

6 = Italy

7 = Spain I

11

= Spain II

12

= Latin America

13

=

Korea

64

= Legal

Overrides the DIP switch settings for the international character set.

Command Summary

9-35

Commands Arranged by Topic

User-defined Characters

See Chapter 4 for sample programs and full information on this topic.

ESC &

Format:

ASCII code:

Decimal:

Hexadecimal:

Define User-defined Characters

ESC & 0 n1 n2 d1

27 38 0 n1 n2 d 2 d a t a

d 1

d 2 d a t a

1B 26 00 n1 n2

d 1

d 2 d a t a

Comments:

This command allows characters to be redefined in the currently selected mode.

When defining characters, DIP switch 2-5 must be set to off.

ESC :

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC 0

2 7 5 8 0 n n

Copy ROM to RAM

0

0

1B 3A 00

n 00

Comments:

This sequence copies the characters in ROM to RAM characters

so that

specific

can

be redefined. The variable n represents the font family.

Fonts in font cartridges (except Orator and Orator-S) can also be copied. The

LQ-1010

cannot select fonts 2 to 6 unless you

have

installed the appropriate font module.

0: Roman 4: Script

1:

Sans Serif

2: Courier

3:

Prestige

5:

OCR-B

6:

OCR-A

9-36 Command Summary --

Commands Arranged by Topic

ESC %

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC %

n

27 37

n

1B

25

n

Select User-defined Set

Comments:

This sequence is used to print the user-defined (download) character set. ESC & is required to define the character set. The following values can be used for

n:

0: Selects the normal set.

1: Selects the user-defined set.

ESC 6

Format:

ASCII code:

Decimal:

Hexadecimal:

ESC 6

27 54

1B 36

Enable Printable Characters

Comments:

When the Epson Extended Graphics character table is selected, ESC 6 enables the printing of codes 128 through 159 (decimal) as characters, not control codes. See the Appendix for characters printed.

ESC 7

Format:

ASCII code:

Decimal :

Hexadecimal:

ESC 7

27 55

1B 37

Enable Upper Control Codes

Comments:

When the Epson Extended Graphics character table is selected, ESC 7 causes codes 128 through 159 to be treated as control codes. This is the default.

Command Summary

9-37

Commands Arranged by Topic

Graphics

See Chapter 4 for sample graphics programs. See the table under ESC * for density information on graphics modes.

ESC K

Format:

ASCII code:

Decimal:

Hexadecimal :

Select Single-density Graphics Mode

ESC K n1 n2

27 75 n1 n2

1B 4B n1 n2

Comments:

Turns on 8-pin, single-density graphics mode. The total number of columns = n1 + (n2 x 256).

ESC L

Format:

ASCII code:

Decimal:

Hexadecimal:

Select Double-density Graphics Mode

ESC L n1 n2

27 76

n1 n2

1B 4C n1 n2

Comments:

Turns on 8-pin, low-speed, double-density graphics mode. The total number of columns = n1 + (n2 x 256).

ESC Y

Format :

ASCII code:

Decimal:

Hexadecimal:

Select High-speed Double-density Graphics Mode

ESC Y n1 n2

27 89

n1 n2

1B 59 n1 n2

Comments:

Turns on &pin, high-speed, double-density graphics mode. The total number of columns = n1 + (n2 x 256).

9-38 Command Summary

Commands Arranged by Topic

ESC Z

Select Quadruple-density Graphics Mode

Format:

ASCII code:

Decimal:

ESC Z n1 n2

27 90

n1

n 2

Hexadecimal: 1B

5A

n1 n2

Comments:

Turns on 8-pin, quadruple-density graphics mode. The total number of columns =

n1 + (n2 x 256).

ESC *

Format:

ASCII code: ESC * m n1 n2

Decimal:

2 7

Hexadecimal:

42

m n1 n2

1B 2A m

n1 n2

Select Graphics Mode

Comments:

Turns on graphics mode m. Refer to the following table for details on the available modes. The total number of columns =

n1 + (n2 x

256).

Option

Pins

Single-density

Double-density

High-speed double-density*

Quadruple-density*

CRT I

CRT II

Single-density

Double-density

CRT III

Triple-density

Hex-density* l

Adjacent dots cannot be printed in this mode.

8

24

8

8

8

8

8

24

24

24

24

m

6

32

33

38

39

40

3

4

0

1

2

Horiz. density

(dots/in)

60

120

120

240

80

90

60

120

90

180

360

Command Summary

9-39

Commands Arranged by Topic

ESC ?

Format:

ASCII code:

Decimal :

Hexadecimal:

ESC ? s m

27 63 s m

1B 3F s m

Reassign Graphics Mode

Comments:

Changes from one graphics mode to another. The variable s is a character (K, L, Y or Z), representing the commands ESC K, ESC L,

ESC Y, and ESC Z.

The variable m has a range of

0

through 6 and corresponds to the mode m in the ESC * command.

9-40

Command Summary

Appendix

Proportional Width Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Character Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6

A - 1

Code

24

25

26

27

28

29

2A

20

21

22

23

2B

2C

2D

2E

2F

Proportional Width Table

This table lists the widths of your printer’s proportional characters. The values given are in 360ths of an inch. (For example, a value of 36 is

36/360ths of an inch.) You may need to enter these widths into a special table for your word processing program so it can calculate the number of proportional characters that will fit on a line.

The characters with no code indicated are international characters or graphics. See the table in Chapter 3 for the relevant codes for the international characters. Also, see the descriptions of the ESC R and

ESC t commands in Chapter 9 for information

on

how to use these characters.

The following width table

shows each

character, its ASCII code

(hexadecimal), and its width. If there are two numbers in the width column, the second one is for the superscript/subscript version of the character.

CHR

*

)

(

+

-

,

/

.

#

$

%

'

&

"

!

Width

30/20

18/12

30/20

30/20

30/20

36/24

36/24

18/12

24/16

24/16

30/20

30/20

18/12

30/20

18/12

30/20

Code

38

39

3A

3B

3C

3D

3E

3F

34

35

36

37

30

31

32

33

CHR

:

9

8

7

3

4

5

6

9

1

2

<

;

Width

30/20

30/20

30/20

30/20

30/20

30/20

30/20

30/20

30/20

30/20

18/12

18/12

30/20

30/20

30/20

30/20

A - 2

CHR

B c

D

@

A

G

H

E

F

K

L

M

N

O

P

I

J

X

Y

Z

S

T

Q

R

U

V

W

]^

\

[

c

a b

Width

36/24

24/16

30/20

36/24

36/24

42/28

36/24

36/24

36/24

36/24

36/24

36/24

36/24

42/28

36/24

42/28

36/24

36/24

36/24

36/24

36/24

36/24

36/24

36/24

36/24

36/24

30/20

24/16

30/20

24/16

30/20

30/20

18/12

30/20

36/24

30/20

Code

5D

5E

5F

60

61

62

63

59

5 A

5B

5C

55

56

57

58

50

51

52

53

54

4C

4D

4E

4F

40

41

42

43

44

45

46

47

48

49

4A

4B

Proportional Width Table

Code

78

79

7 A

7B

7C

7D

7 E

73

74

75

76

77

6C

6D

6E

6F

70

71

72

68

69

6A

6B

64

65

66

67

CHR y z

g

h i d e

f

l

m

j

k n o w x u v

P q r s t

Width

30/20

36/24

30/20

24/16

18/12

24/16

30/20

36/24

36/24

30/20

30/20

30/20

30/20

30/20

30/20

30/20

36/24

18/12

42/28

36/24

30/20

36/24

36/24

30/20

30/20

24/16

36/24

36/24

42/28

36/24

30/20

24/16

36/24

36/24

18/12

24/16

A-3

Proportional Width Table

Width

36/24

36/24

30/20

30/20

30/20

30/20

30/20

30/20

30/20

30/20

36/24

36/24

42/28

30/20

30/20

36/24

42/28

30/20

30/20

18/12

30/20

36/24

30/20

30/20

18/12

18/12

18/12

36/24

36/24

36/24

42/28

42/28

30/20

30/20

30/20

36/24

36/24

Code

CHR

Width

30/20

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30

30/20

30

30

30

30

30

30

C7

C8

C9

CA

CB

C3

C4

C5

C6

CC

CD

CE

CF

DO

D1

D2

BF

CO

C1

C2

BB

BC

BD

BE

B4

B5

B6

B7

BO

B1

B2

B3

B8

B9

BA

A - 4

CHR Width

30

30

30

30

30

30

30

30

30

30

30

30

30/20

30/20

30/20

30/20

30/20

30/20

30

30

30

30

30

30

30

30

30

30/20

30/20

30/20

30/20

30/20

30/20

30/20

30/20

30/20

30/20

Code

F2

F3

F4

F5

F6

F7

EE

E F

FO

F1

E8

E9

EA

EB

E C

ED

DF

EO

E1

E2

DB

DC

DD

D E

E3

E4

E5

E6

E7

D7

D8

D9

DA

D3

D4

D5

D6

Code

F8

F9

F A

FB

FC

FD

FE

Proportional Width Table

CHR

Width

18/12

30/20

30/20

36/24

36/24

30/20

36/24

24/16

30/20

36/24

36/24

30/20

30/20

30/20

42/28

30

30

30

30

30

30

30

A - 5

Character Tables

These character tables are selected by DIP switch

1-7 or the ESC t software command. For the Epson Extended Graphics character table, use of the ESC

6 or ESC 7 software command lets you select whether to print hex codes 80 to

9F as characters (ESC

6) or control codes (ESC

7).

Italic Character Table

CODE 0 1 2 3 4 5 6 7 8 9 A B C D E F

2

3

0

1

4

5

6

7

E

F c

D

A

B

8

9

A-6

Character Tables

Epson Extended Graphics Character Table

CODE 0 1 2 3 4 5 6 7 8 9 A B C D E F

1

0

2

3

4

5

6

7

8

9

A

B

C

D

E

F

A-7

Glossary

Note

that these

definitions apply specifically to printers. If a word is italicized,

see that

topic for more information.

application program

A software program that helps you carry out a particular task, such as word processing or financial planning.

ASCII

Acronym for the American Standard Code for Information

Interchange. A standardized coding system for assigning numerical codes to letters and symbols.

auto line feed

When this feature is enabled using a DIP switch or external control through the parallel connector, the printer will automatically feed the paper one line after receiving a CR code.

baud rate

A measure of the speed of data transmission. Usually expressed in bits per second or bps.

bidirectional printing

Printing in which the print head alternates printing a line left to right then the next line right to left, and so on. Because the head prints in both directions, the overall printing speed increases by eliminating wasted (non-printing) movement.

binary

See number systems.

bit

A binary digit (0 or 1), which is the smallest unit of information used by a printer or computer.

See

also

number systems.

buffer

See input buffer

and

memory.

G l o s s a r y

1

byte

A unit of information consisting of eight bits.

carriage return (CR)

The control code that returns the print position to the left margin.

When issued together with a line feed, the print position moves to the left margin of the next line. In bidirectional printing,

the

print head may not physically move to the left margin.

character set

A collection of letters, numbers, and symbols that provides you with the characters used in a particular language.

condensed

Printing in which

each

character is approximately

60

percent of the width of standard characters. For example, condensed 10 characters per inch (cpi)

has

17 characters per inch. Useful for fitting wide tables or spreadsheets onto the paper.

continuous paper

Paper which has sprocket-feed holes on both long edges, is perforated between pages, and is supplied in a folded stack. Also called fanfold paper.

control code

In addition to the codes for printable characters, the ASCII standard also includes 33 other codes which are called control codes. These control codes perform such functions as sounding the beeper and performing a carriage return or line feed.

cut sheet feeder (CSF)

An optional, detachable device which automatically feeds single sheets of paper into the printer.

data dump

Sometimes called hex dump. A troubleshooting feature. When the printer is in

the

data dump mode,

each

code that it receives is printed in hexadecimal notation.

2

Glossary

decimal

See number systems.

default

A

value or setting that takes effect when the equipment is turned on, reset, or initialized.

DIP switches

Small switches in a printer that control various printer functions and set the default status of the printer when it is turned on or initialized. DIP stands for Dual In-line Package.

dot graphics

A

graphic design formed by patterns of dots. Also called bit image graphics.

dot matrix

A method of printing in which each letter or symbol is formed by a pattern (matrix) of individual dots.

double-high printing

Printing in which each character is twice as tall as normal.

double-strike printing

A way of producing bolder characters. Each character is printed twice; the second time, the dots are printed slightly below the original dots.

Can only be used in draft mode.

double-wide printing

A

print width in which each character is twice as wide as normal characters. (The cpi is halved.)

draft mode

One of two print qualities available on your printer. Draft uses fewer dots per character for high-speed printing. See also

Letter Quality.

emphasized printing

A

way of producing darker characters. In a single pass of the print head, characters receive twice the number of dots.

Glossary

3

Epson Extended Graphics character table

The Epson Extended Graphics character table contains international accented characters, Greek characters, and character graphics for printing lines, corners, and shaded areas.

ESC

(escape) code

A special control code used to begin most printer commands.

ESC/P

Abbreviation for Epson Standard Code for Printers. The system of commands lets you perform software control of your printer from your computer. It is standard for all Epson printers and supported by most application software for personal computers.

font

A font is a style of type designated by a family name.

form

In printer terminology, a form normally refers to a page.

form feed

Refers to both a control code and a panel button that advances the paper to the top of the next page.

hexadecimal (hex)

See number systems.

initialize

To establish the initial default status of the printer by turning the printer on or by sending an INIT signal or code.

input buffer

The memory in the printer in which data sent from the computer is stored while waiting to be printed.

interface

The means of connection between the computer and printer. See also

parallel interface

and serial interface.

italic

A typestyle in which the characters slant.

This sentence is italicized.

4

Glossary

Letter Quality

One of two print qualities available on your printer. Letter Quality provides better readability and appearance at a reduced print speed.

See also

draft mode.

line feed

Both a control code and a panel button

that

advances the paper one line space.

loading position

The position to which the paper is automatically loaded. It can be adjusted by using the micro-adjustment feature.

memory

The printer, like a computer, has a memory. When you print a file from a computer, the contents of the file are transferred quickly from computer’s memory to

the the

printer’s memory. The printer then prints information from its

own

memory at a much slower rate. This way of printing frees the computer to do other work while the printer is still working. The printer memory is sometimes called the buffer memory or input buffer.

micro-adjustment

A

feature that adjusts the paper loading and short tear-off positions by the smallest possible increments.

number systems

Three number systems are commonly used with printers:

decimal

is base 10 and uses the digits 0, 1, 2, 3, 4, 5, 6, 7, 8, and 9.

(This is the most familiar system.)

hexadecimal

(hex) is base

16 and uses

the

digits 0,

1, 2, 3, 4, 5, 6, 7,

8, 9,

A,

B, C, D, E, and F. This is frequently used by programmers.

Any decimal number between 0 and 255 can be expressed by a twodigit hex number.

G l o s s a r y 5

binary

is base 2 and uses only the digits 0 and 1. All information in computer systems is handled in binary form represented by electrical signals that are on or off.

A

binary digit is often called a bit; any decimal number between 0 and

255

can be expressed by an eight-bit binary number.

on line

When the printer is on line, it is able to communicate with the computer connected to it.

paper-out sensor

A small switch behind the platen that sends a signal

when

it is not in

contact

with paper, informing the printer and remote computer

that

there is no paper loaded, and causing the

PAPER OUT

light to go

on.

paper tension unit

The part of the printer that fits above the platen to assure proper paper tension in

the

printing area.

parallel interface

An interface that connects

the

computer and

the

printer. A parallel interface transmits data one character or code at a time. See also

serial interface.

platen

The black roller

that

provides the backing for the paper during printing.

print quality

Your printer has two types of print quality; draft and Letter Quality.

Draft is for high-speed, draft quality jobs; Letter Quality is used to produce more polished documents.

proportional printing

Printing in which the character width varies from character to character. For example, a capital W receives much more space than a lowercase i. The result looks more like a typeset book than a typewritten draft .

6

Glossary

pull tractor unit

An optional device that feeds continuous paper and multi-part forms through the printer.

push tractor

A

built-in device that feeds continuous paper through the printer.

RAM

Acronym for Random Access Memory. The portion of the printer’s memory used

as

a buffer and as a place for storing user-defined characters. All data stored in RAM is lost when the printer is turned

Off.

reset

To return a printer to its defaults, either by a command, an INIT signal, code, or by turning the printer off and on.

self test

A method of checking the operation of the printer. When the self test is run, the printer prints out its current DIP switch settings and the characters that are stored in its ROM (Read Only Memory).

serial interface

A

serial interface transmits data one bit at a time. See also

parallel

interface.

short tear-off

A

feature that automatically feeds the perforation of continuous paper to the tear-off position to be removed by the operator, and then draws the paper back to the loading position. These positions can be adjusted using the micro-adjustment feature. See also

micro-adjustment

and

loading position.

10 cpi

A character spacing of

10

characters per inch. This is often the standard or default pitch. Also referred to as pica.

tractor

The part of the printer that moves continuous paper through the printer by its sprockets gripping the holes in continuous paper.

G l o s s a r y 7

12

cpi

A character spacing in which each character is slightly narrower than normal, so that there are 12 characters per inch. Also referred to as elite.

unidirectional printing

Printing in one direction only. Allows more precise vertical alignment than bidirectional printing. Often used for printing graphics.

user-defined characters

Characters that are defined and stored in the printer by the user. Also known as download characters.

8

Glossary

Index

Command descriptions are not indexed here. To locate the page number of a specific command, see Chapter

9 or the Quick Reference card.

A

Accented characters,

3-22 - 23

Accessories, see Options

Application software,

1-26

Assembling printer,

1-7 - 13

Auto line feed,

3-9

B

Buffer capacity,

3-9

Buttons,

2-16, 3-3

C

Character designing,

4-20 - 31 downloading,

4-22 - 26

fonts,

3-20, 5-34, 8-3

graphics,

3-24 -25 printing,

4-27 - 28 sets, international,

3-22 - 23

size,

3-21, 4-3-4

software control,

9-22 - 40 spacing,

4-2-3, 4-6-8,

9-24-25 tables,

3-24-25, A-6-A-7

Cleaning printer,

6-2 - 4

Column reservation numbers,

4-14

Command summary, 9-1 —

40

Condensed button,

Condensed mode,

Continuous paper,

3-4

Configuring application

Connecting printer,

1-23 - 25

maximum width,

2-8

loading,

2-8 — 15

Control key table, 9-4

Control panel,

3-2 — 5 buttons, 3-3 — 5

lights,

3-2

Cut sheet feeder,

S-2-20

capacity,

8-12

installing,

5-2 — 5 loading paper,

5-6 — 10

mode, 5-5

removing,

5-17 — 20 software control,

5-16

specifications,

8-12 — 13 testing,

5-10 — 13 using,

5-15-17

D

3-21, 4-4 — 5

software,

1-26

Data dump mode,

3-26 — 28

Default settings,

8-14 — 15

Diagnostics, printer, 1-14 — 22

3-26-28, 7-1-23

Index 1

Index

DIP switches, function descriptions, 3-9 — 11,

3-15, 3-22-25

function tables,

3-7

8 setting,

3-6

9

Dot graphics mode, 4-9 — 19,

9-38-40

Double-high mode,

4-3

4, 9-28

Double-strike mode, 4-4 — 5,

4-6-8, 9-29

Double-wide mode, 4-3 — 4,

4-6-8, 9-26-27

Downloading user-defined characters,

4-24-26, 9-36

Draft font,

3-20

Draft mode, 1-20

E

Emphasized mode, 4-4 — 5,

4-6-8, 9-28

Envelopes,

2-30

31

Epson Extended Graphics,

3-24-25, A-7

F

Font button, 3-4

Fonts, see

also

Multi-Font

Module designing,

4-20

31 downloading,

4-22

26 draft,

3-20

letter quality,

3-21

selecting,

3-8, 3-19

user-defined,

4-20

31

Form-feed button,

3-18

G

Graphics mode, 4-9 — 19

Greek characters,

3-24

25

H

Help, where to get, Intro-6

I

Indicator lights,

3-2

Initialization,

8-14

Input buffer capacity, 3-9,

8-2

Interface boards,

5-40 — 50

compatibility, 5-41

installation,

5-41- 48

interface descriptions,

5-40

new serial interface

#8143, s-49-50 specifications, 8-8 —

8-11

International character sets,

3-22-23

Italic character table,

3-24

25,

A-6

Italic mode,

4-5, 4-6

8

L

Labels,

2-28

29

Letter quality mode, 1-21

Lights,

3-2

Line feed button, 3-3

Line feed mode, 3-9

Loading position,

3-12

13

Load/eject button,

2-5, 2-18, 3-3

Locking clip, 1-3 — 1-4

LQ fonts,

3-21

2

Index

M

Master select, 4-6 — 8

Mathematic symbols, 3-24

Micro-adjustment, 3-13

Moving

printer, 6-11

print head, 1-9

Multi-Font Module, 5-34 — 39 font descriptions, 5-34 — 36 installation, 5-37 — 38

selecting fonts, 5-38

Multi-part forms, 2-27

Multi-part light, 3-2

O

On line button, 3-3

On line light, 3-2

Options see Cut-sheet feeder see Interface boards see Multi-Font Module see Pull tractor

Outline mode, 4-6, 9-32

Overline mode, 4-5, 9-31

P

Page length, 3-10

Paper

copy capacity, 8-6

feeding method, 2-2, 8-6

length, 8-3, 8-13

loading, 2-3 — 31

printable area, 8-4-5, 8-13

thickness, 8-5, 8-13 weight, 8-5, 8-13

width, 8-3, 8-13

Index

Paper guide single-sheet paper, 1-12 — 13,

2-3 — 5, 2-16

continuous paper, 2-13

Paper loading position, 3-12 — 13

Paper release lever, 2-3, 2-9

Paper tension unit, 1-4, 1-11

Paper thickness lever, 2-24 — 25

Paper thickness table, 2-26

Paper out light, 3-2

Parallel interface, see

Interface boards

also

connecting, 1-23 — 25 specifications, 8-8 — 11

Pin labels, 4-11 — 12

Platen knob, 1-7-8

Power light, 3-2

Printable area,

continuous paper, 8-4

envelopes, 2-31, 8-5

labels, 8-5

single-sheet paper, 8-4, 8-13

Printable columns, 8-2

Printer assembling, 1-7 — 13 cleaning, 6-2 — 4 connecting to computer,

1-23 — 25 connecting to power source,

1-5

location for, 1-5 — 6 software control, 9-8 — 22 specifications, 8-2 — 7 testing, 1-14 — 22

transporting, 6-11

unpacking, 1-2 — 4

Index 3

Index

Printer cover,

1-13, 2-27

Printer stand,

1-6

Print head,

1-9, 4-10 — 12, 8-6

Printing direction,

8-2

Problems, see Troubleshooting

Proportional spacing,

4-2 — 3,

4-6-8, 9-25, A-2-5

Pull tractor, installing,

5-21— 33

5-21 — 33 loading paper,

5-23 — 29 removing, 5-30 — 33

Push tractor, 2-9 — 23

R

Ready light,

3-2

Ribbon cartridge installing,

1-8 — 10 replacing, 6-5 —

10

specifications, 8-6

Roman font, 3-20

\

S

Sans serif font, 3-20

SelecType options, 3-19 — 21,

5-34

Self test, printer,

1-15-22, s-10-13

Serial interface, see Interface boards

Setting up printer,

1-1 — 26

Shadow mode,

4-6, 9-32

Short tear-off, 3-15 — 18

Single-sheet paper minimum/maximum width,

2-3

loading,

2-3-5, 2-16-23

Size, character, 3-21, 4-3-4

Skip over perforation, 3-11

Software

configuring, 1-26

controlling printer features,

9-1 — 40

Spacing characters per inch, 4-2 — 3 proportional, 4-2 — 3, 4-6 — 8

Special paper, 2-24 — 31

Special printing effects, 4-4 — 8

Specifications, 8-1 — 15 cut sheet feeder,

8-12 — 13 default settings, 8-14 — 15 parallel interface, 8-8 — 11 printer, 8-2 — 7

Strike-through mode, 4-5, 9-31

Subscript mode, 4-6, 9-29 —

30

Superscript mode, 4-6, 9-29 — 30

Switches, see DIP switches

T

Tear-off mode, 3-9

Technical specifications, see

Specifications

Testing printer, 1-14 — 22,

5-10 — 13

Toll-free number, Intro-6

4

Index

Tractor see Pull tractor see Push tractor

Transporting printer,

6-11

Troubleshooting, 7-1 — 34 optional accessories,

7-24 — 34 paper handling,

7-14 — 23

power supply,

7-4

printing,

7-5 — 13

Typestyles,

3-19-21, 4-6-8,

4-20 —

31, see

also

Fonts

U

Underline mode, 4-5, 4-6 — 8,

9-31

Unpacking printer, 1-2 — 4

V

Ventilation,

1-5

Index

Index 5

Control and ESCape Codes by Function

The following control codes are listed briefly for quick reference. For a more detailed explanation, see the page reference in Chapter 9. Variables are not included in this quick reference due to their complexity. For those codes that contain variables, such as ESC Q n for setting the right margin, see Chapter 9.

Printer Operation

ASCII

ESC @

DC1

DC3

DEL

ESC <

ESC U

ESC EM

ESC =

ESC >

ESC #

BEL

Dec.

Hex.

Description

64

17

40

11

Initialize Printer

Select Printer

19 13 Deselect Printer

127

7F

Delete Character

60 3C Select Unidirectional Mode (one line)

85 55

25 19

61

62

3 D

3E

35

7

23

07

Turn Unidirectional Mode On/Off

Control Cut Sheet Feeder Mode

Set MSB to 0

Set MSB to 1

Cancel MSB Control

Beeper

Pg

9-8

9-8

9-9

9-9 s-s

S-10

9-10

9-11

9-11

9-11

9-12

Data Control

ASCII

CR

CAN

Dec.

13

24

Hex.

OD

18

Description

Carriage Return

Cancel Line

Vertical Motion

ASCII

FF

ESC C

ESCCO

ESC N

ESC O

LF

ESC 0

ESC 2

ESC +

ESC 3

ESC A

ESC J

VT

ESC B

ESC b

ESC /

Dec.

12

Hex.

OC

Description

Form Feed

67 43 Set Page Length in Lines

67

78

79

1 0

4 8

50

4 3

43 Set Page Length in Inches

4E

4F

Set Skip Over Perforation

Cancel Skip Over Perforation

0A

Line Feed

30

32

2 B

Select 1/8-inch Line Spacing

Select 1/6-inch Line Spacing

Set n/360-inch Line Spacing

51

33

Set n/180-inch Line Spacing

65 41

Set n/60-inch Line Spacing

74

4A Perform n/180-inch Line Feed

11

66

98

47

OB

42

62

2F

Tab Vertically

Set Vertical Tabs

Set Vertical Tabs i n Channels

Select Vertical Tab Channel pg

9.12

9-12

9-15

9-16

9-16

9-16

9-17

9-17

9-18

9-18 pg

9-13

9-13

9-13

9-14

9.14

9-14

9-15

9-15

Horizontal Motion

ASCII

ESC I

ESC Q

BS

ESC $

ESC \

H T

ESC D

Dec.

Hex.

Description

1 0 8

81

8

36

92

9

68

6C

51

08

24

5C

09

44

Set Left Margin

Set Right Margin

Backspace

Set Absolute Print Position

Set Relative Print Position

Tab Horizontally

Set Horizontal Tabs

Overall Printing Style

ASCII

ESC x

ESC k

ESC !

Dec.

120

107

33

Hex.

78

66

21

Description

Select Letter Quality or Draft

Select Typestyle Family

Master Select

Print Sire and Character Width

ASCII

ESC P

ESC M

ESC g

ESC p

SI

ESC SI

DC2

SO

ESC SO

ESC W

DC4

ESC w

Dec.

Hex.

Description

80

5 0 Select 10 CPI

77

4 D Select 12 CPI

103

6 7

112

15

7 0

OF

Select 15 CPI

Turn Proportional Mode On/Off

Select Condensed Mode

15

OF

1 8

14

14

1 2

OE

OE

5 7

Select Condensed Mode

Cancel Condensed Mode

Select Double-wide Mode (one line)

Select Double-wide Mode (one line)

Turn Double-wide Mode On-Off

8 7

20

119

1 4

7 7

Cancel Double-wide Mode (one line)

Turn Double-high Mode On/Off

Print Enhancement

ASCII

ESC E

ESC F

ESC G

ESC H

ESC S0

ESC S 1

ESC T

ESC ( -

ESC.

ESC q

Dec.

Hex.

Description

6 9

7 0

45

4 6

Select Emphasized Mode

Cancel Emphasized Mode

7 1

72

83

8 3

84

4 0

45

113

4 7

Select Double-strike Mode

48

Cancel Double-strike Mode

5 3 Select Superscript Mode

53 Select Subscript Mode

5 4

Cancel Superscript/Subscript Mode

2 8

Select Score

2 D

7 1

Turn Underline Mode On/Off

Select Character Style

Word Processing

ASCII

ESC a

ESC SP

Dec.

97

32

Hex.

61

20

Description

Select Justification

Set Intercharacter Space

Pg

9 - 1 9

9-19

9 - 2 0

9-20

9-21

9-21

9-22 pg

9-22

9-23

9-23

Pg

9-24

9-24

9-24

9-25

9-25

9-26

9--26

9 - 2 6

9-27

9-27

9-27

9 - 2 8

Pg

9-28

9-28

9-29

9-29

9-29

9-30

9-30

9-31

9-32

9 - 3 2

4

9-33

9-33

Character Tables

ASCII

ESC 1

ESC 4

ESC 5

ESC R

Dec.

Hex.

Description

116 7 4

Select Character Tables

34 Select Italic Mode 52

53

82

35 Cancel Italic Mode

5 2

Select an International Character Set

Pg

9-34

9-34

9-35

9-35

User-defined Characters

ASCII

ESC &.

ESC :

ESC %

ESC 6

ESC 7

Dec.

38

58

37

Hex.

26

3A

25

Description

Define User-defined Characters

Copy ROM to RAM

Select User-deflned Set

54 36 Enable Printable Characters

55 37 Enable Upper Control Codes pg

9-36

9-36

9-37

9-37

9-37

Graphics

ASCII

ESC K

ESC L

ESC Y

ESC Z

ESC’

ESC 7

Dec.

Hex.

75 4B

76 4C

89 59

90 5A

42

63

2A

3F

Description

Select Single-density Graphics Mode

Select Double-density Graphics Mode

Select High-speed Double-density

Select Quadruple-denslty Graphics

Select Graphics Mode

Reassign Graphics Mode

DIP switch settings

DIP Switch 1

SW

1-1

1-2

Description lnternational character set

1-4

1-5

1.6

1-7

1-6

Font selection

Condensed mode on/off

Character table

Cut sheet feeder mode on/off

ON

See page 3-8

OFF

See page 3-8

Condensed

Graphics

On

Normal ltalics

Off pg

9-38

9-38

9-38

9-39

9-39

9-40

DIP Switch 2

SW

2-5

2-6

2-7

2-a

2-1

2-2

2-3

2-4

Description

Page length

Tear-off mode

1-inch skip over perforation

Auto line feed

Input buffer capacity

Not used

Character spacing

'Required for use of user-defined (download) characters.

ON

12 inches

On

O n

On

8 KB

See page 3-a

OFF

11 inches

Off

Off

Off

1 KB

advertisement

Related manuals

Download PDF

advertisement

Table of contents