MDB Family | 4 in 1 Crib | User manual | Crib (2701) - Assembly and Operation Manual

Add to my manuals
8 Pages

advertisement

MDB Family | 4 in 1 Crib | User manual | Crib (2701) - Assembly and Operation Manual | Manualzz
Crib (2701) - Assembly and Operation Manual
Congratulations on purchasing a MDB Family product. This crib will provide many years of service if you
adhere to the following guidelines for assembly, maintenance, and operation. This crib is for residential
use only. Any institutional use is strictly prohibited.
Please be sure to follow the instructions for proper assembly. Use a Phillips head screwdriver for
assembling the crib in addition to the Allen wrench included in the hardware box. Do not use power
screwdrivers. All of our cribs are made from natural woods. Please understand that natural woods have
color variations which are the result of nature and not defects in workmanship.
DO NOT SUBSTITUTE PARTS. ALL MODELS HAVE THE SAME QUANTITY OF PARTS AND HARDWARE. YOUR MODEL MAY LOOK DIFFERENT FROM THE ONE ILLUSTRATED DUE TO STYLISTIC VARIATIONS.
* The crib can later be converted
into a toddler bed or a full-size
bed. To convert to a toddler bed,
turn to page 7. To convert to a
full-size bed, turn to page 8.
revised 20MAR2012
page 1
HARDWARE
A. 3 1/2” Allen
head bolts (6)
B. 1 1/2” Allen head bolts (8)
F. Washers (4)
Tools Needed
(not included)
E. Barrel Nuts(6)
C. 1” Allen head
bolts (4)
G. Lock washers (18)
Phillips
screwdriver
H. Allen wrench
Guard rail hardware :
I. 2” Allen head bolts (4)
J. Lock
washers (4)
CRIB PARTS
K. Front Rail
L. Left Side
N. Headboard
O. Front
Left
leg
P. Front
Right
Leg
M. Right Side
T. Guard Rail
U. Spring frame
R. Rear Q. Rear
Left
Right
leg
leg
page 2
STEP 1.)
Attach legs (R and O, Q and P)
to left and right sides (L and M)
with 4 Allen head bolts (B).
G
R
G
L. Left side
B
B
G
B
G
B
O
G
Q
G
B
Do not overtighten.
G
B
B
G
B
M. Right side
P
STEP 2.)
Attach headboard to the two side rails.
Right side
Left side
A
G
A
G
G
A
E
N.
H
N. ead
Ca bo
be ard
ce
ra
E
Do not overtighten.
G
A
page 3
STEP 3.)
Swing out four hangers at corner of the spring frame (U) carefully to avoid scratching the crib finish.
Attach spring frame FLAT SIDE UP. Choose the height of the spring frame. Start at the highest level
and adjust accordingly.
Bolt the spring frame (U) to headboards using Allen head bolts (C), washers (F), lock washers (G) and
Allen wrench (H). As the child grows, it is important to lower the spring.
Make sure the spring frame is level.
* As your child grows, it is important to lower the
mattress support.
F
U
U.
G
rin
gf
ram
e
Do not overtighten.
C
STEP 4.)
Attach front rail (K) to the crib.
Sp
A
A
G
G
G
A
A
G
G
K.
Fr
on
A
tR
ail
G
A
page 4
KEEP THIS MANUAL IN
A SAFE PLACE FOR
FUTURE REFERENCE.
Recheck all screws and bolts to be sure they
are fastened securely. Do not overtighten.
Before using your crib, please read all cautionary
statements on the insert sheet.
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4 INCHES (69CM)
BY 51 5/8 INCHES (131CM) WITH A THICKNESS NOT EXCEEDING 6 INCHES (15CM).
Please refer to the label (sample below) on the inside face
of the headboard. Record the model/ item number and serial
number of your crib, the name of the store where you made
the purchase, the date of purchase and the wood finish in
the box to the lower right.
WE WILL ASK YOU FOR YOUR SERIAL NUMBER FOR ALL
WARRANTY AND REPLACEMENT PART REQUESTS. PLEASE
REFER TO THE LAST PAGE OF THIS INSTRUCTION SHEET FOR
WARRANTY INFORMATION. KEEP THIS MANUAL FOR FUTURE
REFERENCE.
CAUTION: ANY MATTRESS USED IN THIS CRIB
MUST BE AT LEAST 27 1/4 INCHES (69CM) BY
51 5/8 INCHES (131CM) WITH A THICKNESS
NOT EXCEEDING 6 INCHES (15CM).
THIS PRODUCT CONFORMS TO THE
APPLICABLE REGULATIONS OF THE
CONSUMER PRODUCTS SAFETY COMMISSION.
www.themdbfamily.com
SAMPLE LABEL
Please read the Caution and Warning
Statements insert before using your crib.
page 5
WARNING:
Failure to follow these warnings and
the assembly instructions could result
in serious injury or death.
READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB. KEEP THE MANUAL FOR FUTURE USE.
WARNING:
Parents should ensure a safe environment for the
child by checking regularly, before placing the
child in the product, that every component is
properly and securely in place.
• Do not use this crib if you cannot exactly follow the accompanying instructions.
• Infants can suffocate on soft bedding. Never add a pillow or comforter. Never
place additional padding under an infant.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed
on their backs to sleep, unless otherwise advised by your physician.
• Strings can cause strangulation! Do not place items with a string around a
child’s neck, such as hood strings or pacifier cords. Do not place cords, straps,
or similar items that could become wound around the child’s neck in or near this
crib. Do not suspend strings over a crib or attach strings to toys.
• To help prevent strangulation tighten all fasteners. A child can trap parts of the
body or clothing on loose fasteners.
• DO NOT place a crib near a window where cords from blinds or drapes may
strangle a child. Do not place this crib near a window or a patio door where a
child could reach the cord of a blind or curtain and be strangled.
• When a child is able to pull to a standing position, set the mattress to the lowest
position and remove bumper pads, large toys and other objects that could serve
as steps for climbing out.
• Do not use this crib if the child is able to climb out unaided or is taller than
35 in. (89cm).
• Check this product for damaged hardware, loose joints, loose bolts or other
fasteners, missing parts or sharp edges before and after assembly and frequently
during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if
any parts are missing, damaged or broken. DO NOT substitute parts. Contact
MDB FAMILY for replacement parts and instructional literature if needed.
• DO NOT use a water mattress with this crib.
• For cribs equipped with teething rails, replace teething rail if damaged, cracked
or loose.
• If refinishing, use a non-toxic finish specified for children’s products.
• Never use plastic shipping bags or other plastic films as mattress covers
because they can cause suffocation.
• Infants can suffocate in gaps between crib sides when used with a mattress
that is too small.
• Follow warnings on all products in a crib.
• Ensure that the sides are properly latched or locked in place when the crib is
occupied.
• The mattress used with this crib should not be more than 15cm thick and
should be of such length with width that the gap between the mattress and the
sides of the crib is no more than 3cm when the mattress is pushed into the
corner of the crib.
WARNING:
Please do NOT remove any wood screws
in the normal disassembly of the crib.
ONE YEAR LIMITED WARRANTY:
We will replace any missing parts at the time
of purchase or any defective item within a one
year period from the date of original purchase.
Please keep your receipt so that we may
process your warranty request. This warranty
only covers new units with original packaging
and ownership, and is not transferable. It does
not cover any used, secondhand or demo
models.
This warranty does not cover any damaged or
defective parts that result from installation and
assembly, normal wear and tear, abuse, negligence, improper use or alteration to the finish,
design, and hardware of the crib. The specific
legal rights of this warranty may vary from
state to state. Some states do not allow any
exclusion or limitation of incidental damages.
Some states do not allow limitation on how
long an implied warranty lasts.
Storage:
• Pine woods exchange moisture with the air adjusting to major changes in room temperature and
humidity. Therefore, it is best to place your furniture
away from heating or air-conditioning vents.
• Sunlight is not friendly to solid wood furniture and
prolonged direct exposure to harsh sunlight can
discolor the finish. Be careful not to place your furniture in direct sunlight for extended periods of time. As
with all your fine furniture, blot up spills immediately.
Care and Cleaning:
• Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning. Clean with mild soap on
a soft rag. Rinse and dry thoroughly. If you ever
refinish this furniture, be sure to use only a non-toxic
finish specified for children’s products. If you choose
to refinish this furniture, the warranty will be voided.
Registering your product is even easier than
before. You can register your product on our
website at : www.themdbfamily.com
IF YOU WOULD LIKE TO ORDER
REPLACEMENT OR MISSING PARTS
PLEASE VISIT US AT:
WWW.THEMDBFAMILY.COM
OR YOU CAN CONTACT US BY MAIL:
MDB FAMILY
855 WASHINGTON BLVD.
MONTEBELLO, CA 90640
revised05MAY2011
Crib (2701) - Daybed conversion assembly
* All of the parts and hardware you will need are supplied with the crib at the time of purchase.
STEP 1.) Detach the front rail by
removing 4 A bolts. And move
the spring frame to the lowest
level.
A
A
A
K.
Fro
nt
rai
l
STEP 2.) Install the guard rail using 4 bolts I and J.
A
The guard rail can be installed with the panel
facing the left or the right.
The illustration shows the guard rail with the
panel to the left .
Recheck all screws and bolts to be sure
they are fastened securely.
J
I
Do not overtighten.
T
I
T. G
ua
rd
rai
l
J
T
page 7
The mattress intended for use on the bed shall be a full-size crib mattress having
minimum dimensions of 51 5/8 in. (1310mm) in length, 27 1/4 in. (690mm) in width
and 4 in. (100mm) in thickness, or a greater thickness not exceeding 6 in (152mm).
The intended user’s minimum age must be at
least 15 months old and maximum weight must not exceed 50 lbs (22.7 kg).
WARNING
:
Failure to follow these warnings and the assembly instructions could result in
serious injury or death from entrapment or strangulation.
DO NOT place bed near windows where cords from blinds or drapes may strangle a child. DO NOT place
items with a string, cord, or ribbon, around a child’s neck, such as hood strings or pacifier cords. DO NOT
suspend strings over a toddler bed for any reason. If guard rails are used as the mattress containment
means, guard rails provided must be used to avoid the formation of a gap between the mattress and the bed
that could cause an entrapment.
Conversion Rails (4799-Sold Separately) Assembly Instructions
*For all 4 in 1 cribs, please contact a retailer to order your full size adult wooden bed rails
for your full size bed conversion.
HARDWARE
3” Bolt (8)
Barrel Nut (8)
STEP 1.) Remove the side panel
assemblies.
STEP 2.) Attach the conversion rails
as shown using eight 3” bolts and
barrel nuts.
Do not overtighten.
page 8

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement