2 - W AY C A R ... W I T H R E M O T... MODEL IMPORTANT:

2 - W AY   C A R ... W I T H  R E M O T... MODEL IMPORTANT:
2 - WAY C A R A L A R M S Y S T E M
W I T H R E M O T E E N G I N E S TA R T
MODEL
IMPORTANT:
Please read the entire manual for complete details on the features, accessories and
operation before attempting to use your security system.
This Security system must be installed by a qualified technician to ensure proper
operation. Do not attempt to install or modify this system yourself as
this way void your warranty.
About Your System
Congratulations on your purchase of this state-of-the-art vehicle security system.
With proper installation this system will provide superior protection and performance for
many years to come.
What is included:
A control module
Tranceiver module
One 5-button 2-way LCD remote transmitter
One 4-button random code remote transmitter
Dual stage shock sensor
High output 6-tone siren (optional)
Full set wire harness
Pin switches
Options and Accessories:
This system includes several optional inputs and outputs allowing the creation of a
completely personalized security and convenience system by offering many optional
features such as:
2nd stage door unlock
Channel programme time output
2pulse signal door unlock
Engine turbo time mode
Check range notification
Arm/disarm chirp on/off
Window close control
Anti car-jack by ignition turn
Power trunk/hatch release
Glass breakage sensor
Micro-wave detector
Back-up battery siren
*Many require additional parts and/or labor, see store for details
NOTE:
Some of the features described in this manual may required additional parts and/or
labor, and may not be included as part of the standard installation of this unit.
Additionally, many features of this security system have selectable options that must be
activated or programmed during the system's installation. These items will be identified
in the following sections. Please discuss these features and any questions you may
regarding the installation of this product with your authorized dealer.
Functions of remote transmitters
The remote transmitters integrated with the security system use the most perfect and
reliable radio frequency transfer as opposed to all car security systems being sold at the
moment. Some of modern skilled car hijackers use the devices known as code grabbers
allowing to accept and keep a signal transferred by the remote control of the car security
system. As soon as the driver is out the code is used by the hijacker to disarm the system.
Unlike the remote controls described above the remote transmitters integrated with your
security system change the code of the transferred signal each time when the button is
pressed, therefore, when a hijacker reproduces the signal grabbed from your remote
transmitter, the security system just will not react.
2-way remote #TR-45
1-way remote #TX-4R
Fig.1
Functions of remotetransmitter buttons
Button to arm the system (ARM)
Button to disarm the system (DISARM)
Button to control remote engine start
Button to control Trunk open / CH-1 active
Button to check car status , to turn on LCD back light
Standard LCD 2-way icon instructions
Remote transmitting a signal.
Check-in range turn ON status.
2way battery level indication.
System Armed.
System Disarmed.
Silent Armed.
Passive arming &
Auto re-arming mode.
Zone1
1st-stage sensor bypass.
Zone1
2nd-stage sensor bypass.
Zone2
1st-stage sensor bypass.
Zone2
2nd-stage sensor bypass.
Panic mode.
Door open when armed.
Zone1
1st stage sensor triggered.
Zone2
1st stage sensor triggered.
Hood switch triggered.
Trunk open when armed.
Zone1
2nd stage sensor triggered.
Hood open when armed.
Zone2
1st stage sensor triggered.
Door switch triggered.
Trunk switch triggered.
Ignition switch triggered.
Immobilizer mode.
Anti car-jacking mode.
Remote engine running mode.
Temperature engine start mode.
Battery conservemode.
Valet mode.
Safety mode/ Safe status
Clock time engine start mode.
Fix time engine start mode.
Turbo mode.
Remote button lock
Call / page mode.
Vibrate mode.
Remote Function Table:
Functions
Step
Condition
Arm and door lock
Press
once
Disarmed & ACC off
Arm without siren chirp
Press
over 2sec. until 1 beep given.
Disarmed & ACC off
Zone1- 1st-stage bypass
Press
once within 5sec. of arming.
Arming within 5sec.
Zone1- 2nd-stage bypass
Press
twice within 5sec. of arming.
Arming within 5sec.
Car search mode
Press
once after 5sec. of arming.
Arming after 5sec.
Standby Anti-Hi-Jack mode
Press
over 2sec. Until 1 beep given.
ACC ON
Disarm and door unlock
Press
once
Armed
Disarm without siren chirp
Press
over 2sec. until 1 beep given.
Armed
Arm with engine run mode
Press
over 2sec. Until 1 beep given.
Engine running
Remote engine start
Press
over 2sec. then press
Remote engine stop
Press
over 2sec.
Engine running mode
Safety mode (manual-type car) Press
over 2sec.
Engine running
Zone2- 1st-stage bypass
Press
once within 5sec. of arming.
Arming within 5sec.
Zone2- 2nd-stage bypass
Press
twice within 5sec. of arming
Arming within 5sec.
once. Armed with safe status
Remote Function Table:
Functions
Trunk open / CH-1 active
Step
Press
Condition
over 2sec. until 1 beep given
Prolong engine running time Press
once, after LCD indicate 3min left.
Engine running mode
Enable check-in range
Press
once within 5sec. of arming.
Arming within 5sec.
Status check & Back light
Press
once
Indoor temperature check
Press
over 2sec. Until 1 beep given.
Silent armed
Press
over 2sec. Until 1 beep given. ACC OFF
Valet mode
Press
over 2sec. until 1 beep given. ACC ON
Panic mode
Press
over 2sec. until 1 beep given.
ACC OFF
Anti-Hi-Jack mode
Press
over 2sec. until 1 beep given.
ACC ON
FIX time engine start
Press
once
Armed with safe status
Temperature engine start
Press
over 2sec. until 1 beep given. Armed with safe status
CH-2 active
Press
over 2sec. until 1 beep given.
CH-3 active
Press
over 2sec. until 1 beep given.
CH-4 active
Press
over 2sec. until 1 beep given.
Functions
Step
Condition
Remote button lock (on/off)
Press
over 2sec. until 1 beep given.
Vibrate mode on/off
Press
over 2sec. until 1 beep given.
Clock time adjust mode
Press
over 2sec. until 1 beep given.
Clock time engine start
Press
over 4sec. until 2 beep given.
Battery conserve mode
Press
over 2sec. until 1 beep given.
Remote battery discharge/replacement
If the battery becomes exhausted, the remote will emit extra long beep, While press any
button on the remote, few seconds later the
indicator will flashing for identify.
The battery discharge is displayed on the LCD screen as the icon with the status indicator .
Also you can pay your attention that the effective distance for the transmitter is being
reduced.
To replace the batteries of 2-way remote
-
Bend the top part of the cover a bit, move it up and remove,
Remove the discharged battery,
Place the new battery (AAA) observing polarity,
Carefully place the cover back.
To replace the batteries of 1-way remote
- Loose the screws on the back side of the transmitter housing and separate two halves of
the transmitter housing,
- Remove the discharged battery,
- Place the new battery 12V 23A observing polarity,
- Carefully place the cover back (please do not damage the LED and switchers on the
Circuit board);
tighten the screws on the back side of the transmitter housing.
Programming of codes for new transmitters
Important
Please notice that during the programming of a new transmitter into the system memory all
previous programmed codes of the transmitters will be erased so in case of programming
for additional transmitters the available transmitters shall be programmed again.
The system supports in memory up to four codes of remotes irrespective of the fact if the
codes of four different remotes or the same code four times is recorded into the system.
Programming of new transmitters.
Important
Please notice that each following operation shall be done within 10 sec after the previous
operation. If the 10 second period is over the system will automatically exit the
programming mode and two long chirps will acknowledge the exit. If the ignition is turned off
during programming the system will immediately exit the programming mode and two long
chirps will acknowledge the exit.
1. Disarm the system .
2. Turn the ignition from on to off.
3. Within 10 sec after switching off the ignition press and hold the Valet button over 3 sec ,
the LED starts flashing , release the Valet button.
4. Press and hold the Valet button, you will hear the siren start chirping (from 1~3 chirp),
while give 2 chirp sound, immediately release the Valet button.
5. The LED will start flashing to acknowledging that the system is ready for programming of
new transmitters.
6. Press any button of the first transmitter, you will hear 1-short chirp acknowledging that
the first transmitter has been programmed
Press any button of the second transmitter, you will hear 2-short chirp acknowledging
that the second transmitter has been programmed.
Repeat the operation 3 for other transmitters.
7. To exit the transmitter programming mode, Turn on the ignition and you will hear two long
siren chirps.
Programming 2-Way remote
Battery conserve mode
The mode can be turned on/off 2-way receiving in the Disarmed mode if you simultaneously
press down the buttons
until the zzz icon turn on. Being in the Disarmed mode
the remote pager turns off its receiver in 30sec.
To exit the mode, simply press the buttons
until zzzz icon turn off.
2-way LCD display :
2way remote button lock ON/OFF
For safety purpose, this 2-way remote can be lockout the remote button in order not to
mis-touched the buttons. Press button
for over 2sec. until one beep is heard,
remote button is now locked. To turn on remote button, press button
for over
2sec. until two beeps is heard, remote button is now unlocked.
2-way LCD display :
Vibrate mode on/off
Press button
the button
Beeps
1-beep
1-beep
for over 2sec. the 2-way remote will respond tone & vibrate feature,
pressing 2sec. will change the feature, see under table:
Vibrations
2-way remote feature
1-time
Remote with tone and vibration
1-time
Remote with vibration only
Remote with tone only
Check-in range notification (on/off )
Arming the system within 2 seconds, press button
system will enable this Check- in range function.
The 2way remote
will respond:
once on the 2way remote , the
This Icon will turn on and give 1 beep
sound to indicate the function has been
turned ON.
- With in 5 minutes, the 2-way remote will than give 1 beep sound every one minute for 5
cycles to remind the user within range.
- After 5 minutes, the 2-way remote will detect range every 10 minutes and without any beep
sound, the icon
will constant on if the user within range.
For friendly usage, the 2-way remote will provide 2 beeps/ 3cycles and flashing icon
if the user is out of the receiving rage. However, afterwards if the 2-way remote detect the
signal again from the system, the icon
will be ON to indicate the 2-way remote is within
range.
Note: If under Check-in range mode, if alarm triggered, this function will automatically
turn off (disable).
Time adjust mode
Besides operating for alarm functions, LCD remote control additionally provides 24-hour
real time clock.
Instructions:
1. Press and hold Button
for 2sec. to enter time-setup mode, 1 beep will be heard.
2. Press button
to select Hour & Min adjust setting. Icon flashing to indicate.
24-hour display
Minutes display
3. Press button
to turn up the numbers. Press button
to turn down the numbers.
The button may be held down to scroll faster.
4. Press button
to exit the setting mode. 2 beep will be heard.
Note: The remote will revert to normal operation from the set mode when 10-seconds has
elapsed without a button entry.
Vehicle status checking
The 2-Way remote offer the feature to check the current status of the car, simply press the
button
once within proper operation range. The main unit will send the signals to the
2-Way remote about the vehicle current status.
Turn on LCD display back light
Simply press button
once, the back light of LCD display will turn on 5 seconds and
also check the vehicle status.
2-way signal paging features
A page is the signal the control module sends to the remote controls confirmation of
receipt of a command or alarm system status. When the remote control receives a page
it will generate a page notification to the user (notifications are audible beeps) and the
LCD Icons will display the current system status.
Command Page
When a command (arm/disarm, remote start , or auxiliary channel) from the remote
control is sent and received, the system will send a command page back to confirm receipt.
Note: When the system is in Valet mode, the remote control will show the lock icon and
unlock icon, but will not generate a command page.
Page Recognition (Acknowledgement)
To clear a page alert/notification, quickly press any button on the remote control. This
can be performed at any time during or after the page notification has occurred.
The remote control will not send a command to the system at this time; it will only clear
future repeats of the page notification. The next time a button is pressed on the remote
control it will send a command to the system.
Alarm Page
If the alarm system is triggered while armed, an Alarm Page will be sent to the remote
control. When the remote receives an Alarm Page, the LCD icons will display the alarm
system status information and the remote control will generate beeps.
Alarm Page table
Display
Beeps
5 short
Vibrations
1 times
Trigger
Zone 1
1st stage-Sensor warning
Melody 1 1 times periodically
Zone 1
2nd stage-Sensor triggering
5 short
Zone2
1st stage-Sensor warning
1 times
Melody 1 1 times periodically
Zone 2
2nd stage-Sensor triggering
Melody 2 2 times periodically
Trunk switch triggering
Melody 3 3 times periodically
Door switch triggering
Melody 4 4 times periodically
Hood switch triggering
Melody 5 5 times periodically
Ignition triggering
Standard features
- To ARM the system: Press the button
once.
To arm your system within proper operation range, simply press button
once (while
system in disarmed or Acc off position) . The system will respond one siren chirp, one lights
flash, doors lock, disable engine starter, the status LED will flash approximately once per
second, indicating that the system is actively protecting your vehicle.
IMMO icon
indicate that
the engine
blocked
2-way LCD display :
- Arm without siren chirp :
Press the button
over 2sec.
You may temporarily to arm your system without siren chirp , to operate it by simply press and hold
the button
for over 2sec. until the remote give 1 beep sound, then release the button
.
The system will armed and without one siren chirp.
Note: this features is only activated under the system is in disarmed and Acc off position,.
- Defective Zone Bypass & Alert:
If the security system is armed at the same time that an input is active (such as a door opening
or hood / trunk opening ), you will hear one siren chirp to indicate arming and after 5 seconds
a second siren chirp to indicate bypass Notification. A Bypass Notification chirp means that the
security system ignores the input that was active when the system was armed, until that input
ceases.
Note: You may press 2-way remote button
Defective zone
Siren chirps
once to check again which zone is not closed.
2-way beeps
Door opened
4 chirps
1 long + 3 short
Trunk opened
5 chirps
1 long + 4 short
Hood opened
6 chirps
1 long + 5 short
2-way LCD indicator
Passive arming: (Table-1 of No.2 ON status)
If set programme mode to "ON", while turn Ignition OFF, then close the last door , the LED
will starts flashing and Siren will give 2 chirps and Lights flash twice t o indicated that the
system is in passive arming mode. After 30sec. The system will arm by itself and LED
flashing slowly to show the system is in arming mode. Main unit sends the signal to the 2Way LCD remote and indicates ARM mode with one beep sound .
Two beep sound will provided to
to indicate that the system is in
Passive arm mode.
2-way LCD display :
Icon flashing
indicator
Note: If during the operating of the passive arming timer if a door is being opened the
Operating of the passive arming timer will be suspended. As soon as all doors, hood
and trunk are closed the system will start the cycle of the passive arming again. As
soon as 30 seconds are over the armed mode will be turned On.
- Automatically rearming : (Table-1 of No.4 ON status)
If the system is disarmed by remote and a door is not opened within approximately 30 seconds the
system will automatically rearm itself. This feature guards against disarming caused by accidental
or unintended operation of the remote transmitter. Main unit will sends signal to the 2-Way LCD
remote and indicates ARM mode with one beep sound.
Flashing icon to indicate
that the system is in Auto
re-arming mode.
2-way LCD display :
Icon flashing
indicator
- When armed your vehicle is protected as follows:
Light impacts trigger the sensor. When triggered, the siren will give 3 chirps.
Heavy impacts trigger the sensor. The sequence consists of the siren sounding
continuously and the parking lights flashing for 20 seconds.
If a door is opened, the system will immediately start chirping the siren and flashing the
parking lights for 30seconds.
Turning on the ignition key will trip the same progressive response as opening a door.
Turning on the trunk or hood will trip the same progressive response as opening a door.
The optional starter kill prevents the vehicle's starter from Cranking.
- Alarm cycle :
If a violation occurs the system will respond by sounding the siren and flashing the lights for
approximately 30sec. before the system resets itself and continues to protect your car. If
violation still occurs the system, siren and lights will working for 4 or 5 cycles then the
system reset itself and continues to protect other zones.
- Zone-1 / Zone-2 : 2nd stage sensor triggering limited for 4 cycles
- Door / Hood / Trunk zone triggering limited for 5 cycles
- To DISARM the system : Press the button
once.
To disarm your system within proper operating range, simply press button
once (while
system in arm position). The system will respond two siren chirp, two light flash, doors
unlock, Enable your engine starter, LED off.
2-way LCD display :
+ Two beep sound
- Disarm without siren chirp :Press the button
over 2sec.
To disarm your system without siren chirp , simply press and hold the button
for over
2sec. until the remote give 1 beep sound, then release the button
. The system will
disarmed and without one siren chirp.
Note: this features is only activated under the system is in armed position.
- 2 step disarm:
This system offers 2 step disarm. It's a feature that make it possible to silence and reset
the system while it is triggering, without disarming the system. If the system is triggered
and the siren has been sounding, pressing any button once on the remote transmitter will
stop the trigger and return the unit to the armed state.
Note: Under system triggering, if press any button of 2-way remote once , the remote will
stop the beep sound and LCD display will indicate the intrusion icon for 2sec.
Press any button again to stop alarm triggering.
- 2nd step release start killer (Table-1 of NO.7 ON status) :
If programmed with this feature, when disarming the system by the remote, however the
engine will still blocked, the status LED will fast flashing 4 times after a pulse and the 2way
LCD will turn on the icon
for indication.
To exit : Turn ignition ON then (1) press Valet (over-ride) switch once . (2) or press remote
button
once to release the start killer . The status LED will off to indicate the engine
released .
- Disarming without a transmitter : (table-1 of No.6 Valet sw status)
The security system can be disarmed without the remote transmitter. The function
is provided for the case when you need to disarm the system and drive the car but the
Remote transmitter is faulty or lost. If while the programming of the system for the manual
disarming the Valet (table-1 of No.6) was selected act as follows to disarm the system:
open the car door - the security system will be triggered and the siren will be turned on; turn
on the ignition, press the Valet switch once to disarm the system.
- Disarming by using the PIN code : (table-1 of no.6 PIN code status)
To select the PIN coded disarming mode. Please contact your installation technician or see
Functions to be programmed section and the Installation manual. If the coded disarming
mode is on you can use the manufacturer code (25) or to provide the maximum arming of
your car you can program your own PIN code for disarming at any time. The code comprises
two digit; each digit can vary from 1 to 9.
To disarm the system using the PIN code
1. Open the door with the key (the system will be triggered and the parking lights will go on
and so on).
2. Turn ON the ignition .
3. Press the Valet button 2 times , the number of times which is in accordance with the first
digit of your PIN code (the manufacturer setting is 2 time).
4. Turn OFF the ignition then turn ON again.
5. Press the Valet button 5 times, the number of times which is in accordance with the
second digit of your PIN code (the manufacturer setting is 5 time).
6. System will automatically disarmed if insert the correct PIN code.
Note:
If you enter the wrong code , you must wait next cycle triggering and turn off the ignition
then start from step #2.
- Silent arming mode : Press the button
over 2sec.
To temporarily turn off the arm or disarm chirps, use Silent mode. Simply press the button
1+2 over 2sec.. The system will armed without siren chirp. Disarm the system the siren will
be automatically returned into the normal mode.
2-way LCD display :
+ One beep sound
Note: The Zone1 and Zone 2 sensors are bypassed if the system is armed using Silent
Mode. This ensures that no chirps will be emitted by the siren in an area you want chirp-free.
The system is still fully capableof triggering. Only the sensor is bypassed.
- Panic (turning on/off) : Press the button
over 2sec.
The system will be immediately armed , and siren turned on and the parking lights will start
flashing for 30 seconds.
To turn off the panic mode, press any button once of the remote . If you do not turn off the
panic mode the system will be automatically turned off in 30sec. and in armed .
Under Panic mode, the
2-way remote will respond
melody sound and flashing
icons .
2-way LCD display :
Icon flashing
indicator
- Car search mode:
The system provide a feature to easy find your car position, simply press button
once
when in armed after 5sec. The system will respond by 1-long chirp with 10sec. for the
parking lights flashing.
- Passive immobilizer: (Table-1 of NO.3 ON status)
To turn on the function of passive locking of the engine contact an installation technician or
see the section Programmed functions (Table-1 of NO.3 ).
If programmed with this function, when turn off ignition switch for 30 seconds or you open
and close the door, it will disable the engine starter right way . The status LED will fast
flashing 4 times after a pulse and the 2way LCD will turn on the IMMO icon.
2-way LCD display :
+ Two beep sound
Turning off of the passive locking of the engine
- If the ignition is turned on press the disarming button 2 for a short time to cancel the
function of the passive immobilizer
- If the transmitter is faulty or lost turn off the system with the Valet switch .
- In door temperature check :Press the button
over 2sec.
This feature provide temperature check inside the vehicle , simply press the button
over 2sec. the 2way LCD will indicate icon to show the current temperature .
2-way LCD display :
for
Icon turn on for
current temperature
inside the car
- Intrusion Alert by status LED :
Upon disarming the system, if the vehicle is attempted or intruded, siren and lights will
Indicates 5 chirps and 5 flashes to identify which zone was triggered. LED mode indicates
the following different triggering.
flash 2 times after a pause
Sensor 1st-stage triggered
flash 3 times after a pause
Sensor 2nd-stage triggered
flash 4 times after a pause
Door switch triggered
flash 5 times after a pause
Hood switch triggered
flash 6 times after a pause
Trunk switch triggered
Flash 7times after a pause
Ignition switch triggered
- 2-way LCD Intrusion Alert:
Upon disarming the system, if the vehicle is attempted or intruded, the 2-way remote will
respond 2 short beep follow with melody sound, and LCD display will indicates different
icons as under:
Zone1: 1st-stage
sensor triggered
Zone1: 2nd-stage
sensor triggered
Zone2: 2nd-stage
sensor triggered
Door switch triggered
Hood switch triggered
Zone2: 1st-stage
sensor triggered
Trunk switch triggered
Ignition switch triggered
Note: Before the ignition turn on, you may realized again which zone been triggered by
Press
button (status check) once, the LCD will display triggered zone again.
- Dual stage shock sensor:
This device only activates after 5 seconds of arming state; this is preventing from the
weak impact caused by the driver while leaving the car.
-Light impact will activate the 1st stage sensor by giving 3 short warning chirps. 2-way
remote will respond 5 beeps and flashing icon as under.
Zone 1 - 1st stage
sensor trigger
Zone 2 -1st stage
sensor trigger
With 5 beeps sound
With 5 beeps sound
2-way LCD display :
-Heavy impact will activate the 2nd stage sensor and trigger the alarm for 20sec. 2-way
remote will respond melody and flashing icon as under.
Zone 1 -2nd stage
e sensor trigger
Zone 2 -2nd stage
sensor trigger
2-way LCD display :
With Melody sound
With Melody sound
NOTE: Adjustments are made via the rotary control above the shock sensor.
- Remote Zone1 sensor bypass: Press the button
within 5sec. of amring.
This system offer 2 stage sensors bypass feature . Within 5sec. after set arming, to press
button
once , the system will give 2 short chirps , the 1st stage bypassed. Press button
Once again, within 5sec. the system will give 3 short chirps, the 2nd stage bypassed.
Zone1- 1st stage
sensor bypass.
Zone1- 2nd stage
sensor bypass.
With 2 beeps sound
With 3 beeps sound
2-way LCD display :
Note: - if remote sensor bypassed, it will be detected again by next arming.
- if armed with silent mode, to operate sensor bypass will only indicate by lights flash.
- Remote Zone2 sensor bypass: Press the button
within 5sec. of amring.
This system offer 2 stage sensors bypass feature . Within 5sec. after set arming, to press
button
once , the system will give 2 short chirps , the 1st stage bypassed. Press button
Once again, within 5sec. the system will give 3 short chirps, the 2nd stage bypassed.
Zone2- 1st stage
sensor bypass.
Zone2- 2nd stage
sensor bypass.
With 2 beeps sound
With 3 beeps sound
2-way LCD display :
Note: - if remote sensor bypassed, it will be detected again by next arming.
- if armed with silent mode, to operate sensor bypass will only indicate by lights flash.
Valet mode
I f you are going to have your vehicle serviced, parked by a valet or washed you will want to
put your security system Into valet mode. To enter valet mode as follows:
With Valet button:
1. Disarm the system .
2. Turn the ignition from on to off.
3. Within 10 sec after switching off the ignition press and hold the Valet button over 3 sec ,
the LED starts flashing , release the Valet button.
4. Press and hold the Valet button, you will hear siren chirp (from 1 to 3 chirp sound), while
give 1 chirp sound, immediately release the Valet button. You will automatically at Valet
mode, the LED steady ON .
With remote:
1. Turn the ignition to ON status.
2. Press the button
for over 2sec. until the status LED steady ON.
2-way LCD display:
Note:
Under Valet mode, each time
turn Acc off , the siren will give
2 chirps for notification.
When the system is in the valet mode it can not be armed. The door lock and unlock will
function as keyless entry system.
To exit valet mode:
Turn Ignition switch to ON position , then press button
for over 2seconds. You
will hear siren provide 2 long and LED light OFF to confirm exit this mode and in alarm mode.
The 2-Way remote will respond 1 long and 2 short beeps.
Manage Engine start /running features
- Safe status :
This system has several important safety input to ensure proper operation of the motor and
prevent accidental damage to the engine or its components.
If one of the under list input is defective , the engine will not allow to start.
- The hood switch is opened.
- The Hand brake switch off
- Not in Park switch gear position.
- Safety mode :
Arming the system the 2way remote will turn on the safety mode icon
, it will allow to
engine start if the icon is turn on. If one of the zone's been triggered, the icon will turn off
and engine start is not available . It will able to engine start by next arming again.
Note: this Safety mode will turn OFF if door switch opened when arming.
over 2sec.
- Safety mode for manual-type car: Press the button
This safety feature for the car with manual-gear type (Table-3 of NO 4), before set the
engine start mode, you have to set the system in Safety mode.
To set safety mode:
1. In safe status, Engine running , press the button
for over 2sec.
2. The parking lights will active to indicate in safety mode.
3. Remove the ignition key, and leave the car , however the engine still running.
4. Arm the system, and the 2-way LCD will indicate Safety icon as under:
Note: this Safety mode will turn OFF if door switch opened when arming.
Icon on if the
safety mode active.
2-way LCD display :
- Remote start : Press the button
over 2sec. then press
once.
This feature allows you to remotely start and run your vehicle for a programmable period of
time. This makes it possible to warm up the engine, as well as the system is in Safe status.
Important!
(1) Never remote start your vehicle when the keys are in the ignition, except when
performing "Arm with engine run mode", and (2) Never start the vehicle if it is not in Park
switch gear position and not Hand brake on .
To remote start the vehicle:
1. Armed position, press the button
for over 2sec. Then within 2sec. Press the button
Once.
2. The parking lights will flash 3 times to confirm that the vehicle will attempt to start.
3. Once the vehicle has started, it will run for the pre-programmed period of time
(either 10, 20,30 minutes or unlimited - see Table-3 of NO.1 section ) or until a shutdown
input is triggered.
4. The 2-way LCD will indicate engine run icon and engine run time icon as under:
Run time icon will turn on 2sec. for programmed time of (
,
,
,
). and then it will display every 2sec. of
alternate run-time and current-time.
Note: if programmed with unlimited
, it will display only for
current-time without run-time.
2-way LCD display
if engine started :
Extension engine running time 10 minutes:
To prolong the engine running time again by press the button
time will start from 10 minutes, except set in unlimited time.
Flash icon if
engine started.
once, the engine running
When you are ready to drive the vehicle:
1. Disarm the system, if programmed with delay time (Table-3 of NO.12)
2. Insert the ignition key and turn it to the ON (not the START) position.
3. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut
down.
Shutdown input :
While the vehicle is running during remote start operation, the system will monitor the
vehicle and will automatically shut down the engine if the system receives any of the
following shutdown inputs:
- The brake pedal is pressed.
- The hood is opened.
- The hand brake switch off / Park switch gear off position.
- The pre-programmed run time (10, 20, or 30 minutes) has elapsed.
- Press the button
over 2sec.
- Fix time engine start : Press the button
once.
This feature will automatically engine start for every (2/3/4/24 hour) check programme
Table-3 of NO.2. This makes it possible to warm up the engine (Table-3 of NO.1 ), as well
as the system is in Safe status.
To active Fix time engine start the vehicle:
1. Armed position, press the button
once.
2. The 2-way LCD will indicate fix time icon and hour icon as under:
Run time icon will on for 2sec.
To indicate fix time every (
,
,
,
) hour.
2-way LCD display :
Turn on to indicate
Fix time start enable
Exit the FIX time engine start mode:
1. Under the mode, press the button
once again.
2. The 2-way LCD will turn off fix time icon and give 2 beep sound.
- Temperature engine start : Press the button
for over 2sec.
This feature will automatically engine start when the programme temperature detect ( -5C,
-10C,-20C,-25C) check programme Table-3 of NO.3. This makes it possible to warm up the
engine (Table-3 of NO.1 ), as well as the system is in Safe status.
To active Fix time engine start the vehicle:
1. Armed position, press the button
for over 2sec.
2. The 2-way LCD will indicate ( ) icon and temperature icon as under:
3. The main unit will detect the vehicle temperature after 10sec.
Turn on to indicate
temp.start enable
2-way LCD display :
Programme temp. icon will on for 2sec. to indicate
detect temp. As:
(
,
,
,
)
Exit the FIX time engine start mode:
1. Under the mode, press the button
for over 2sec. again.
2. The 2-way LCD will turn off temp. icon and give 2 beep sound.
- Clock time engine start: Press the button
over 2sec. for twice time.
This feature will engine start by pre-setting clock time. This makes it possible to warm up
the engine (Table-3 of NO.1 ), as well as the system is in Safe status.
To set clock time engine start the vehicle:
1. press the button
over 2sec. then press again the button
2 beep sound will be heard and clock icon flashing :
over 2sec.
2. Press button
to select Hour & Min adjust setting. Icon flashing to indicate.
3. Press button
to turn up the numbers. Press button
to turn down the numbers.
The button may be held down to scroll faster.
4. Press button
to enable clock time. 1 beep will be heard and exit the mode.
Press button
to disable clock time. 2 beep will be heard and exit the mode.
Note: The remote will revert to normal operation from the set mode when 10-seconds has
elapsed without a button entry.
Exit the Clock time engine start mode:
1. press the button
over 2sec. then press again the button
over 2sec.
2 beep sound will be heard and clock icon flashing.
2. Press button
to disable clock time. 2 beep will be heard and exit the mode.
-Arm with engine run mode: (Table-1 of No.8 ON status)
This feature allows the vehicle to remain running after the key has been removed from the
ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for
short periods of time, but would like to leave the motor running and the climate controls on.
The engine running time can be programmed (2/5/10/untimited time (Table-1 No.9).
To perform Arm with engine run mode:
1. Before turning off the engine, make sure the system is in Safe status as: ( Hood switch
closed, Hand brake on, Park switch gear on.)
2. Press the button
over 2sec. The status LED will start flashing twice per second and
the parking light will active as programme (Table-3 of NO.5)
3. Turn the ignition key to the OFF position. (The engine will stay running.)
4. Press the button
, to arm the system , however the engine will keep running.
The engine will run until the pre-programmed time elapses or a shut-down input is
received. (See the Remote Start section for a complete list of shut-down inputs.)
Note: This feature will not work if the brake pedal is being pressed.
2-way LCD display :
Icon flashing
indicator
Anti-Hi-Jack mode
This feature will protect your vehicle in the event that there is an attempt to Hi-jack the
vehicle. The system allows using three independent or simultaneous options to turn on the
function Anti-Hi-Jack.
If the system turned on Anti-hI-Jack mode, the parking lights will flash 1 time and the LED
will start flashing fast indicate that the mode is turned on.
- Standby door switch activates:
To operate it when driving the car, press button
for over 2seconds, siren will give
one chirp and LED start flashing twice per second, system now is in standby Anti carjacking mode. Under this standby mode, if a door is forced been open and close, the system
will activate Anti-HI- jack mode immediately. The parking lights will flash once and the LED
will fast flash to show the system is enter anti car-jack mode.
EXIT: Under standby mode, you may exit this mode, if it is not activate the door, press
button
for over 2 seconds, siren will give two chirps and LED off.
- Remote Anti-Hi-Jack: (Table-1 of NO.5 remote status).
1. Turn on the ignition or start the engine.
2. Simultaneously press the buttons 1+3
until the acknowledgement signal
,1 flash of parking lights and the status LED start flashing.
- Ignition turn Anti-Hi-Jack: (Table-1 of NO.5 ignition status).
If programmed with the feature, each time ignition switch has been turn ON , the system will
auto enter anti-hi-jack mode. The parking lights will flash once and the status LED will start
flashing to show the system is enter anti car-jack mode.
- Door switch Anti-Hi-Jack: (Table-1 of NO.5 Door switch status).
If programmed, to operate it when driving the car, if a door is forced been open and close,
the system will activate Anti-car jack immediately. The parking lights will flash once and the
LED will fast flash to show the system is enter anti car-jack mode.
2-way LCD display :
The AHJ icon will turn on
after 60sec. of active the
mode.
- Anti car-jack mode table:
If enter anti car-jack mode, the Parking lights will flashing once and the LED will fast
flashing to show the system is enter anti car-jack mode.
While proceed at 60sec. main unit sends signal to the 2-Way remote a
2-way LCD display :
The AHJ icon will turn on
after 60sec. of active the
mode.
Anti-Hi-Jack mode table
LED flash
Lights flash
Flashing normally
LED flashing fast
Flashing
1 flash
Warning chirp
Siren
Siren turn on
Locking the engine circuits
Engine circuit
Timer
0sec.
50sec.
60sec.
90sec.
Turning off of the Anti-Hi-Jack mode
Exit within 60sec. : Turn ignition off then on . press button
for 2sec. or press valet
switch once ,siren will give two chirps and LED off.
Exit after 60sec. :
1- Within Disarm switch (Table-1 of NO.6 Valet sw status) :
After entering this mode, simply press the Disarm switch once .
2- With PIN code (Table-1 of NO.6 PIN code status) :
To exit this mode with the PIN code , Turn off then on the ignition , press the Valet button to
insert the pin code , please check the function " Using the PIN code ".
Additional service functions to control the system
- Remote controlled additional channel (CH-1)
The system has the channel CH-1 to control various additional devices connected to the
system. This channel "Gray wire" is a negative pulsed output. The channel can be used
for : (Table-2 of NO.5)
- Remote trunk open .
- Remote Latched.
- Remote control of with the programme timer (1~120sec.) and sensor zones off.
- Remote control of with the programme timer (1~120sec.) and sensor zones on.
. Control of the CH-1 (Trunk open) - Press the button
over 2sec.
Simply press and hold button 4 over 2 seconds, the channel will output for 1 second pulse ,
to open the trunk. When armed if remote trunk open or close, the 2-way remote will give one
beep sound and display icon as under:
2-way LCD display :
Note. If the CH1 channel output is enable when the system was in the armed mode the
system will simultaneously turn off the shock sensor and the trunk trigger. As soon as the
trunk is closed the system will automatically re-arm the circuit and turn the shock sensor on.
Note: (1) Ignition ON does not allow to remote trunk open.
(2) Armed, if trunk keep opened over 1 minutes, the 2-way remote will give pre-warn
beep sound.
. Control of the CH-1 (Remote latched) - Press the button
over 2sec.
Simply press and hold button 4 over 2 seconds, the channel will constant output .
To exit by press and hold button 4 over 2 seconds, the channel will deactivated.
. Control of the CH-1 (programming time output with sensor off /on) Press the button
over 2sec.
Simply press and hold button 4 over 2 seconds, the channel will constant output for the preprogrammed period of time or until press the button 4 over 2 seconds.
The sensor zones can be turn off or on status , during the channel activated, check Table-2
of NO.5.
- Program controlled additional channel (CH-2)
The system has the channel CH-2 to control various additional devices connected to the
system. This channel "White/black wire" is a negative pulsed output. The channel can
be used for : (Table-2 of NO.6)
- Disarming pulsed output for 30 seconds .
- Remote Latched.
- Remote control of with the programme timer (1~120sec.) and sensor zones off.
- Remote control of with the programme timer (1~120sec.) and sensor zones on.
. Control of the CH-2 (Disarming output for 30sec.)
If programmed , the channel will constant output 30sec. when disarming. This feature
for the car with dome-light supervision.
. Control of the CH-2 (Remote latched) - Press the button
over 2sec.
Simply press and hold button 1+4 over 2 seconds, the channel will constant output .
To exit by press and hold button 1+4 over 2 seconds, the channel will deactivated.
. Control of the CH-2 (programming time output with sensor off /on) Press the button
over 2sec.
Simply press and hold button 1+4 over 2 seconds, the channel will constant output for the
pre-programmed period of time or until press the button 1+4 over 2 seconds.
The sensor zones can be turn off or on status , during the channel activated, check Table-2
of NO.6.
- Program controlled additional channel (CH-3)
The system has the channel CH-3 to control various additional devices connected to the
system. This channel "Gray/black wire" is a negative pulsed output. The channel can be
used for : (Table-2 of NO.7)
- Arming pulsed output for 30 seconds .
- Remote Latched.
- Remote control of with the programme timer (1~120sec.) and sensor zones off.
- Remote control of with the programme timer (1~120sec.) and sensor zones on.
. Control of the CH-3 (Arming output for 30sec.)
If programmed , the channel will constant output 30sec. when arming. This feature for
the car with window closing after arming.
. Control of the CH-3 (Remote latched) - Press the button
over 2sec.
Simply press and hold button 2+4 over 2 seconds, the channel will constant output .
To exit by press and hold button 2+4 over 2 seconds, the channel will deactivated.
. Control of the CH-2 (programming time output with sensor off /on) Press the button
over 2sec.
Simply press and hold button 2+4 over 2 seconds, the channel will constant output for the
pre-programmed period of time or until press the button 2+4 over 2 seconds.
The sensor zones can be turn off or on status , during the channel activated, check Table-2
of NO.7.
- Remotecontrolled additional channel (CH-4)
The system has the channel CH-4 to control various additional devices connected to the
system. This channel "Orang/black wire" is a negative pulsed output. The channel can
be used for : (Table-2 of NO.8)
- 2nd stage door unlock .
- Remote Latched.
- Remote control of with the programme timer (1~120sec.) and sensor zones off.
- Remote control of with the programme timer (1~120sec.) and sensor zones on.
. Control of the CH-4 (2nd stage door unlock)
If you select this function the stage-by-stage unlocking of driver's then passengers' doors
one after another is automatically carried out with the remote transmitter if you sequentially
press the disarming button. Control of unlocking of the passengers doors by the signal of
one of additional channels (CH4 ) to be programmed respectively.
When you first time press the disarming button 2 the system will enable driver's door
unlocking and when you press the button once again the CH4 will be enabled for
Passengers' doors unlocking.
. Control of the CH-4 (Remote latched) - Press the button
over 2sec.
Simply press and hold button 3+4 over 2 seconds, the channel will constant output .
To exit by press and hold button 3+4 over 2 seconds, the channel will deactivated.
. Control of the CH-4 (programming time output with sensor off /on) Press the button
over 2sec.
Simply press and hold button 3+4 over 2 seconds, the channel will constant output for the
pre-programmed period of time or until press the button 3+4 over 2 seconds.
The sensor zones can be turn off or on status , during the channel activated, check Table-2
of NO.8.
- Program controlled additional channel (CH-5)
This channel "Orange wire" is a negative pulsed output. The channel can be used for:
(Table-2 of NO.3)
- Armed output (for interlock N/C type)
- Disarmed output (for interlock N/O type)
This CH-5 output for the car with engine start killer feature while active the system.
Armed or disarmed output can be programme by Table-2 of NO.3 . This wire may be wired
to an optional starter kill relay .
- Additional channel (CH-6)
This channel "Yellow wire" is a negative pulsed output. This CH-6 output for the car with
engine start killer feature as soon as system disarmed. This wire may be wired to an
optional starter kill relay .
2-way LCD display :
To indicate that the
engine blocked.
CH-5/CH-6 activated.
- Additional (alarm) call if alarm call button located on the antenna
module of the transceiver is pressed
- The system has an additional channel to transfer the signal to call for/notify the owner of
the two-way communication remote. The call can be made by the second person being in
the car and enabling the call button on the module of the antenna pager. The call is
formed by pressing the call button .
- The two-way communication remote will start issuing frequent beeps few seconds.
Call button
Transceiver
Receivertransmitter unit
# BASE-2
LED
indicator
2-way LCD display :
LED
indicator
To indicate that the call
button activated.
Changing of the PIN code to turn off the system
This system provide 2 digit PIN code, each digit code can be programme from 1 to 9 , and
manufacturer code is ( 2.5).
To program your new PIN code as follows:
1. Disarm the system .
2. Turn the ignition from on to off.
3. Within 10 sec after switching off the ignition press and hold the Valet button over 3 sec ,
the LED starts flashing , release the Valet button.
4. Press and hold the Valet button, you will hear siren chirp (from 1 to 3 chirp sound),
while give 3 chirp sound, immediately release the Valet button.
You will automatically at the PIN code setting mode. Siren will give 1 long chirp sound.
5. Enter the first digit of the code with the Valet button (the number of pressing the Valet
button corresponds to one digit of the code);
Press remote button 1 once to confirm the first code, by given 1 chirp sound.
6. Enter the second digit of the code with the Valet button (the number of pressing the
Valet button corresponds to the second digit of the code);
Press remote button 1 once to confirm the second code, by given 2 chirp sound.
7. If PIN code correct insert , the siren will give 1 long chirp to acknowledging that the
system is ready for programming of new PIN code, see next step #9.
If PIN code incorrect insert, the system will exit the mode by given 2-long chirp.
<< Suppose that you want set new PIN code is 3.8 >>
8. To programme the 1st PIN code by press the Valet button the number of times
corresponding to the 1st digit of your PIN code. Press 3 times of the Valet button,
(each time the Valet button is pressing, the status LED will activated) .
9. Press the remote button 1 once, siren will give 1 chirp to confirm the 1st digit code .
10. To programme the 2nd PIN code by press the Valet button the number of times
corresponding to the 2nd digit of your PIN code. Press 8 times of the Valet button,
(each time the Valet button is pressing, the status LED will activated) .
11. Press the remote button 1 once, siren will give 2 chirp to confirm the 2nd digit code .
12. Wait a second, the status LED will notify the 2 digit PIN code, by 3 flashes - pause - 8
flashes.
13. If you wish to change the new PIN code again, press and hols the Valet button until
transceiver give 1 long beep, to indicate that you can programme again from above
step 9 .
14. To Exit the mode, turn ignition to ON , and you will hear two long siren chirps.
You must write down or remember your PIN code.
Note:
Please notice that the time between your actions shall be less than 20 sec; otherwise the
system will automatically exit the programming mode and you will hear two long siren chirps.
Entering the programming mode
1. Disarm the system .
2. Turn the ignition from on to off.
3. Within 10 sec after switching off the ignition press and hold the Valet button over 3 sec ,
the LED starts flashing , release the Valet button.
4. Press and hold the Valet button, you will hear siren chirp
(from 1-short
2-short
3-short
1-long
1-long+1-short
1-long+2shot ),
5.
While give 1-long chirp , release the Valet button to programme Table-1.
While give 1-long+1short chirp , release the Valet button to programme Table-2.
While give 1-long +2short chirp , release the Valet button to programme Table-3.
6. After release the Valet button, you will automatically at the programming mode for the
No.1 function. The LED starts flashing as separate flashes and the lights will turn ON.
The number of the LED flashes in the programming mode for a certain function
Corresponds to the programmed function number;
7. - Change the status of the function by press the button 1.2. 3.4 of the transmitter. You will
hear 1, 2, 3,4 siren chirps depending on the new status of the function,
- Switch into the next function by press the Valet button one time.
- Exit the programming mode (e.g. turn on the ignition).
Note
Please notice that the time between your actions shall be less than 20 sec; otherwise the
system will automatically exit the programming mode and you will hear two long siren chirps.
PROGRAMME TABLE-1
Press the
Valet SW
to next item
Item NO. by
LED flash
Press button
Press button
Press button
Press button
1-chirp
2-chirp
3-chirp
4-chirp
PROGRAMME
FEATURES
No.1
Foot brake & Ignition control
door lock / Ignition off unlock
No.2
Passive arming
No.3
Passive immobilizer
No.4
Automatically Rearming
No.5
Anti-Hi-Jack mode
No.6
Emergency disarm by :
Valet Switch / Pin code
No.7
2nd step release start killer
No.8
Arm with engine run mode
No.9
Arm with engine run time
Factory settings
Foot brake IGN on10sec IGN on10sec
Lock/
Lock/
Lock /
W/o
IGN off
IGN off
Unlock
Unlock
Unlock
OFF
ON
OFF
OFF
ON
With door
locking
OFF
OFF
ON
ON
OFF
OFF
ON
With door
locking
OFF
ON
ON
ON
ON
By Door SW
Activate
By ignition
turn on
By remote
activate
Valet SW Valet SW Pin code Pin code
OFF
OFF
ON
ON
ON
ON
OFF
OFF
2minutes
5 minutes 10 minutes Unlimited
PROGRAMME TABLE-2
Press the
Valet SW
to next item
Item NO. by
LED flash
Press button
Press button
Press button
1-chirp
2-chirp
3-chirp
4-chirp
0.8 sec.
3.5 sec.
Lock0.8sec.
Unlock2pulse
Lock30sec.
Unlock0.8sec.
5 sec.
15 sec.
45 sec.
60 sec.
PROGRAMME
FEATURES
No.1
Manage door lock/unlock
No.2
Door switch delay while
arming
No.3
Controlled channel (-) CH-5
output
No.4
Press button
Interlock
N/C Type
Interlock
N/C Type
Interlock
N/O Type
Interlock
N/O Type
Armed output
Armed output
Disarmed
output
Disarmed
output
OFF
OFF
ON
ON
Trunk open
Pulse output
1sec
Remote
latched
by key-1
Exchange CH-1/CH-2 &
Lock / Unlock channel .
Lock output = gray wire (-)
Unlock output = white/black wire (-)
CH-1 output = internal lock relay
CH-2 output = inter unlock relay
No.5
Controlled channel (-) CH-1
output
No.6
Controlled channel (-) CH-2
output
No.7
Controlled channel (-) CH-3
output
No.8
Controlled channel (-) CH-4
output
Disarming
Pulse
output
30sec
Programme Programme
time output time output
1~120sec.
1~120sec.
sensor on
sensor off
Programme Programme
Remote
time output time output
latched
1~120sec.
by key-1+4 1~120sec.
sensor on
sensor off
Programme Programme
Remote
Arming
time output time output
latched
Pulse output
1~120sec.
by key-2+4 1~120sec.
30sec
sensor off
sensor on
2nd stage
unlock
Programme
Remote
time output
latched
by key-3+4 1~120sec.
sensor off
Programme
time output
1~120sec.
sensor on
Note: How to programme No.5~No.8 timer output
While in programme item No.5~No.8 ,to programme the channel timer output by pressing
the button
or
, at the time the siren will give chirps and the LED will steady ON ,
the programmer now is in counting time (from 1~120sec.) , after your desire time, pressing
the button
or
again, thus the channel has been programmed the time output.
PROGRAMME TABLE-3
Press the
Valet SW
to next item
Press button
Press button
Press button
Press button
1-chirp
2-chirp
3-chirp
4-chirp
PROGRAMME
FEATURES
Item NO. by
LED flash
10 minutes 20 minutes 30 minutes
Unlimited
No.1
Engine run time after start
No.2
Time start engine by each
2 / 3 / 4 / 24 hou rs
2 hour
3 hour
4 hour
24 hour
No.3
Auto start engine by
temperature detect
-5 C
- 10 C
- 15 C
- 25 C
Auto-type /Manual-type car
Auto-type Auto-type Manual-type Manual-type
(-) safety sw (+) safety sw (-) safety sw (+) safety sw
No.4
safety switch -/+ signal detect
No.5
Parking lights activate when
remote engine running
Flashing Flashing Constant
No.6
Blue wire (CON1)
ACC(+) output
Active when Active when Active when Active when
Engine is
ACC is on IGN1 is on Engine is
running
(Green wire) (Yellow wire) running
No.7
Start engine crank time
0.8 sec.
1.4 sec.
2 sec.
3.6 sec.
No.8
Engine type (start delay)
Petrol
(Delay2sec.)
Diesel
(Delay4sec.)
Diesel
(Delay6sec.)
Diesel
(Delay10sec.)
No.9
Engine control detect
Voltage
"noise"
Tacho
sensor
Turo off Safety mode
Generator Generator
(+)
(-)
if
No.10
Zone1&Zone2 triggered
No.11
when Engine start running
No.12
press
Bypass Zone-1& Zone-2
Shut down engine run when
Factory settings
button to disarm
OFF
OFF
Zone1
Zone2
Zone1+2
2nd stage 2nd stage 2nd stage
Triggered triggered triggered
OFF
Zone1
Bypass
Zone2
Bypass
Zone1+2
Bypass
OFF
Delay
10sec.
ON
ON
System Installation:
1. Thoroughly read and become familiar with the installation instructions before
beginning the installation.
2. Review system contents: (1). A control module. (2).2-way pager transceiver antenna
(3). One 5-button 2-way LCD remote transmitter.
(4).One 3-button random code remote transmitter
(5).Dual stage shock sensor (6).High output 6-tone siren (optional)
(7).Harness:
. 24-Pin main harness . 4-pin x2 shock sensor harness.
. 7-pin transceiver harness . 3-Pin (40a) block relay harness
3. Verify with the owner, the mounting location for all visible components, including the
LED and Valet/over-ride switch.
4. Verify with the owner, the optional programme features.
5. Inspect and perform a function test for all vehicle systems before and after the
installation.
6. Always use a Volt / Ohm meter for testing vehicle circuits. Never use a test light.
7. Always look before drilling any holes or mounting self-tapping screws. Be sure fuel
lines and exterior wiring looms are clear as they often close to the chassis and difficult
to see.
8. Protect all wires running from the engine compartment to the interior of the vehicle by
covering with electrical tape and split loom tubing. Be sure to use a grommet when
routing wires through the firewall.
9. Properly fuse any additional accessories such as window module, trunk opener, etc.,
making sure to power them separate from the alarm module. This will ensure the
functionality system in the event of an accessory failure.
Mounting the Control Unit
The control unit only be mounted in the inter of the vehicle. Do not mount the main unit in
the engine compartment. Choose a mounting location that will not be easily accessible
to a thief, and will not interfere with the operation of any vehicle components, such as
foot pedal, steering column, air vents, seat rails, etc.
Do not mounting the control unit until after setting the internal jumpers and performing
a complete operation check of the system. After installation is complete and
performance verified, the control unit can be easily mounted using wire ties through the
mounting tabs on the button of the unit.
Mounting the Shock Sensor
Choose a suitable interior mounting locating for the shock sensor that provides ample
coverage of the vehicle. Keep the sensor away from the vehicle's ECM or other sources
of the electrical interference. Suggested mounting locations include air conditioning
ducts, dashboard braces, or center console supports.
During proper operation, the shock sensor will detect impacts to the vehicle only and
will not usually br triggered by slow rocking movements of the vehicle like those caused
by wind.
2nd stage (-) trigger
1st stage(-) trigger
- Ground
+12V DC output
WIRING DIAGRAM :
Green
Blue
Black
Red
Dual-stage/zone
Shock Sensor
Antenna
Extend the whole wire, align it with the intersection
of dashboard and the front window glass.
Keep it away from the metal at least 5 cm to have
the best receiving condition.
1
2
ZONE1
Plug-in dual stage
shock sensor
ZONE2
External
Ultra sonic &
micro-wave
sensor port
LED
indicator
LED
indicator
Push button
Call switch
External
Temperature
Sensor
E8
Use external temperature
sensor for measurement of
engine temperature or
temperature in the given
point of car compartment.
Install the sensor in nearby
engine .
Plug-in Valet/ over-ride switch
Main control unit
20-PIN CON2
Main connector
wiring
6-PIN CON3
Connector
for door lock
wiring
6-PIN CON1
Connector
for Engine start
wiring
20-PIN CON2 main connector wiring
1
2
3
4
5
6
7
8
10
9
(-) CH-6
Connect to Chassis
Ground (-)
20
11
Yellow
Black
(-) 300mA negative
pulsed when
disarmed output
(killer2)
(-) Safety switch
Connect to (-)
negative Hood
pin switch
Foot brake (+)
input
Hand brake (-)
input
Pink
Red/black
(-) CH-1 (prog.)
Green/white
Gray
(-) 500mA negative pulsed
output for Trunk open
Blue/white
Connect to (-)
negative Trunk
pin switch
Connect to
Existing (+)
Positive
Door Switch
Connect to
Existing (-)
Negative
Door Switch
(-) negative input
Connect to the
Park switch gear in
the vehicle.
(-) CH-2 (prog.)
White/black
Blue
White
(-) 500mA negative
output 30sec. when
disarming.
Right side parking
light output
(-) CH-3 (prog.)
Purple
Gray/black
White
(-) 500mA negative
pulsed output 30sec.
when arming.
Left side parking
light output
Green
(-) CH-4 (prog.)
Orange/black
(+) Siren output
Brown
(-) 500mA negative
pulsed output for 2nd
stage door unlock
(-) Factory disarm output
Engine control input (prog.)
By tachometer or generator
White/red
Yellow/black
(-) CH-5 (prog.)
(-) 500mA negative pulsed
when armed output (Killer1)
Orange
(-) 500mA negative output
to disarm factory antitheft device
(-) Original bypass output
Black/white
(-) 500mA negative output when
active engine run and start on .
6-PIN CON1 Connector for Engine start wiring
IGN1 output(+)
the wire will active
when remote start
and engine running
Yellow
Black/yellow
3
Positive power
(+) 12VDC input
2
1
Yellow/black
Starter input (+)
blue
6
30A
red
5
4
Green
Starter ON output (+)
ACC (+) output (prog.)
(acc circuit , air-con &
heater..)
check Table-3 of No.6
ACC ON output (+)
6-PIN CON3 Connector for Door Lock wiring
Green/red
Door Lock N/O
Green
Door Lock COM
Green/black
Blue/red
Door Lock N/C
Door Unlock N/O
Door Unlock COM
Blue/black
Blue
Door Unlock N/C
4-PIN Connector for sensors
(+)12V DC
(-) When Armed
Red
Green
Black
Blue
1st stage (-) input
2nd stage (-) input
CON1 engine start wire connection guide:
The six heavy gauge wires coming from the large connector are used to energize high
current circuits in the vehicle. It is crucial that these connections are well-made and
capable of handling the current demands.
Black/yellow (+) starter output
Connect this wire to the starter wire in the vehicle.
Yellow/black starter input
For anti group or starter kill attach this wire to the key side of the starter wire for anti grind
and for the starter kill to be active.
RED (+)12V input for high current outputs
Remove the 30-amp fuses prior to connecting these wires and do not replace them until the
satellite has been plugged into the control module. These wires are the source of current for
all the circuits the relay satellite will energize. They must be connected to a high current
source. Since the factory supplies (+)12V to the key switch that is used to operate the motor,
it is recommended that these wires be connected there.
Yellow(+) Ignition #1 ON output
Connect this wire to the ignition #1 wire in the vehicle. This wire will immediate active when
remote start and engine running .
Green(+) ACC ON output
Connect this wire to the ACC ON wire in the vehicle. This wire will activate when remote
engine running.
Blue (+) ACC(+) output (prog.)
This wire will activate for programme (Table-3 of No.6)
CON2 wire connection guide:
Black/white (-) original bypass output
This wire supplies a 500mA output as soon as the module with remote start process. It can
be used with a relay to disconnect a sensor from the system as shown below.
This wire can also be used to rearm a factory anti-theft system when the remote start shuts
down.
To bypass an optional sensor:
Black/white
original bypass
output
SENSOR TRIGGER
OUTPUT
CUT
(+) 12V FUSED
SENSOR INPUT
OF SYSTEM
Yellow/black (-) factory disarm output
This wire sends a negative pulse every time the remote start is activated. This can be used
to pulse the disarm wire of the vehicle's factory anti-theft device. Use a relay to send a (-) or
(+) pulse to the disarm wire as shown in the diagrams below.
Relay for Negative (-) Disarm Wire
Relay for Positive (+) Disarm Wire
Yellow/black (-)
factory disarm output
Yellow/black (-)
factory disarm output
(+)12V
To disarm (-)
wire
(+)12V
To disarm (+)
wire
(+)12V
White/red Engine control input ( tachometer or generator input)
This input can be programmed three ways to detect engine status - run or not .
( Tachometer RPMs & Generator (+) /(-) & Voltage "noise" ) .
by programmable (Table-3 of No. 9)
- Control by tacho sensor:
This input provides the module with information about the engine's revolutions per minute
(RPMs). connection to such circuit is ensure right starter disconnection. There are some
cars where tacho signal amplitude is lower than 4V. Therefore you need to use additional
Capacitor .
1
11
2
3
4
5
6
7
8
9
10
20
White/red wire
1.0 uf/250V
To Tachometer sensor
- Control by generator (+) or (-):
connect the wire to "generator charge lamp" on dashboard. This wire circuit must
changed from 0V(engine stop) to 9-12V (engine running) or from +12V to 0V (Table-3 of
No. 9) there are some car models where +12V is appear when starter is running.
- Control by Voltage "noise" :
When you can't use engine control by tacho and by generator. Starter disconnection
according to the Table-3 of No.9 , white/red wire do not used.
Green/White (+) Foot brake input
This wire MUST be connected to the vehicle's brake light wire. This is the wire that shows (+)
12V when the brake pedal is depressed. The remote start or turbo mode will be disabled or
shut down any time the brake pedal is depressed.
Foot brake
Green/white
+ 12V
STOP lamps
Blue/White (-) Hand brake input
This wire MUST be connected to the vehicle's brake light wire. This is the wire that shows
(-) when the hand brake is ON. The remote start or turbo mode will be activate if the brake
Is ON position.
+12V
Hand brake lamp
on dashboard
Hand brake
Green/white
Red/black (-) Safety switch input (prog.)
Connect the wire to the PARK gear (-)switch in the vehicle. This wire will test with ground
with the gear selector in PARK position. This will prevent the vehicle from accidentally being
started while in a drive gear. This input must rest at ground in order for the remote start
system to operate. Connected properly the vehicle will only start while in PARK gear
position. This wire can be programmed (-) / (+) signal detect by table-3 of No.4.
(-) signal Safety sw
(+) signal Safety sw
+12V
Park gear
Red/black
Park gear lamp
+ 12V
Park gear lamp
Park gear
Red/black
Black (-) chassis ground connection
Remove any paint and connect this wire to bare metal, preferably with a factory bolt rather
than your own screw. (Screws tend to either strip or loosen with time.) We recommend
grounding all your components, including the siren, to the same point in the vehicle.
ORANGE (-) CH-5 ground-when-armed output (prog.)
This wire supplies a (-)500 mA ground as long as the system is armed (if programmed
armed output by (Table-2 of No.3). This output ceases as soon as the system is disarmed.
The orange wire may be wired to an optional starter kill relay.
6-PIN Connector for Central Door Locking Wiring
1.) For Factory installed central door lock system
MOTOR CONTROL
ORIGINAL
BUILT-IN
CONTROLLER
MOTOR CONTROL
DOWN
DOOR MOTOR LOCK
(Inside of the front door)
UP
MAIN LINE
Central door lock wiring
Green/black
Green
Green/red
Blue/black
Blue
Blue/red
2.) Directly connect to 2 wire Actuator
Central door lock wiring
+ 12V
2 WIRE ACTUATOR
Green/black
Green
Green/red
Blue/black
Blue
Blue/red
LOCK MOTOR
UNLOCK MOTOR
(-)GND
3.) A built-in Central door lock with electric lock switch( like: CHRYSLER.. )
+ 12V
Central door lock wiring
Green/black
Green
Green/red
Blue/black
Blue
Blue/red
DOWN
ELECTRIC
MOTOR
MOTOR LOCK
INSIDE THE
FRONT DOOR
UP
4.) For vacuum type central door lock system ( like : Mercedes Benz , AUDI.. )
Green/black
Green
Green/red
Blue/black
Blue
Blue/red
Note: Door lock active time for 4 secs.
+ 12V
Central door lock wiring
ELECTRIC
MOTOR
DOWN
AIR COMPRESSOR
UP
Made in Taiwan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement