D-Link DI-614+ Installation guide

D-Link DI-614+ Installation guide
D-Link AirPlus DI-614+
Enhanced 2.4GHz Wireless
Broadband Router
Manual
Building Networks for People
Contents
Package Contents ................................................................................ 3
Introduction ........................................................................................... 4
Wireless Basics .................................................................................... 6
Getting Started ..................................................................................... 9
Using the Configuration Menu ............................................................ 10
Troubleshooting .................................................................................. 50
Networking Basics .............................................................................. 55
Technical Specifications ..................................................................... 68
Contacting Technical Support ............................................................. 70
Warranty ............................................................................................. 71
Registration ........................................................................................ 74
2
Package Contents
Contents of Package:
 D-Link AirPlus DI-614+ Enhanced 2.4GHz Wireless Broadband Router
 Power Adapter – 5V DC, 2.5A
 Manual on CD
 Quick Installation Guide
Note: Using a power supply with a different voltage rating than the one included with
the DI-614+ will cause damage and void the warranty for this product.
If any of the above items are missing, please contact your reseller.
System Requirements For Configuration:
 Computer with a Windows, Macintosh, or Linux based
operating system with an installed Ethernet adapter
 Internet Explorer or Netscape Navigator, version 6.0 or above,
with JavaScript enabled
3
Introduction
The D-Link AirPlus DI-614+ Wireless Broadband Router is an enhanced 802.11b
high-performance, wireless router. It is an ideal way to extend the reach and number
of computers connected to your wireless network.
Unlike most 802.11b routers, the DI-614+ is capable of data transfer speeds up to
22 Mbps* (compared to the standard 11 Mbps) when used with other D-Link AirPlus
products such as the DWL-520+ Wireless PCI Adapter.
After completing the steps outlined in the Quick Installation Guide (included in your
package) you will have the ability to share information and resources, such as files
and printers, and enjoy the freedom that wireless networking delivers.
The DI-614+ is compatible with most popular operating systems, including
Macintosh, Linux and Windows, and can be integrated into a large network. This
Manual is designed to help you connect the Router and the D-Link AirPlus 2.4GHz
Wireless Adapters into a network in Infrastructure mode. Please take a look at the
Getting Started section in this manual to see an example of an Infrastructure network
using the DI-614+.
This manual provides a quick introduction to wireless technology and its application
as it relates to networking. Please take a moment to read through this manual and
get acquainted with wireless technology.
*Maximum wireless signal rate derived from IEEE Standard 802.11b specifications. Actual data throughput
wil vay. Network conditions and environmental factors, including volume of network traffic, building materials
and construction, and network overhead lower actual data throughput rate.
4
Connections
Auto-Sensing Ports:All ports (both LAN and
WAN) auto-sense cable types to accomodate
stright-through or cross-over cable.
LAN ports provide
connections to Ethernetenabled devices.
WAN port is the
connection for the
Ethernet cable to the
Cable or DSL modem
Pressing the Reset
Button restores the
router to its original
factory default
settings.
Receptor
for the
Power
Adapter
LEDs
WAN LED: A solid light
indicates connection
on the WAN port. This
LED blinks during
transmission.
Power LED: A solid
light indicates a
proper connection to
the power supply.
WLAN LED: A solid light
indicates that the wireless
segment is ready. This
LED blinks during wireless
transmission.
M1 LED: A solid light
indicates that the DI-614+
is ready.
M2 LED: A solid light
indicates that the unit is
defective.
Local Networ LED: A solid light
indicates a connection to an
Ethernet-enabled computer
on ports 1-4. This LED blinks
during data transmission.
5
Wireless Basics
D-Link AirPlus wireless products are based on industry standards to provide easy-to-use
and compatible high-speed wireless connectivity within your home, business or public
access wireless networks. Strictly adhering to the IEEE standard, the D-Link AirPlus
wireless family of products will allow you to access the data you want, when and where
you want it. You will be able to enjoy the freedom that wireless networking delivers.
A wireless local area network (WLAN) is a cellular computer network that transmits and
receives data with radio signals instead of wires. Wireless LANs are used increasingly
in both home and office environments, and public areas such as airports, coffee shops
and universities. Innovative ways to utilize WLAN technology are helping people to work
and communicate more efficiently. Increased mobility and the absence of cabling and
other fixed infrastructure have proven to be beneficial for many users.
Wireless users can use the same applications they use on a wired network. Wireless
adapter cards used on laptop and desktop systems, support the same protocols as
Ethernet adapter cards.
Under many circumstances, it may be desirable for mobile network devices to link to a
conventional Ethernet LAN in order to use servers, printers or an Internet connection
supplied through the wired LAN. A Wireless Access Point (AP) is a device used to
provide this link.
People use wireless LAN technology for many different purposes:
Mobility - Productivity increases when people have access to data in any location within
the operating range of the WLAN. Management decisions based on real-time information
can significantly improve worker efficiency.
Low Implementation Costs – WLANs (Wireless Local Area Networks) are easy to set up,
manage, change and relocate. Networks that frequently change, both physically and
logically, can benefit from WLANs ease of implementation. WLANs can operate in
locations where installation of wiring may be impractical.
Installation Speed and Simplicity - Installing a wireless LAN system can be fast and easy
and can eliminate the need to pull cable through walls and ceilings.
Network Expansion - Wireless technology allows the network to go where wires cannot
go.
Reduced Cost-of-Ownership - While the initial investment required for wireless LAN
hardware might be higher than the cost of wired LAN hardware, overall installation
expenses and life-cycle costs will be significantly lower. Long-term cost benefits are
greatest in dynamic environments requiring frequent moves, adds, and changes.
Scalability – Wireless Local Area Networks (WLANs) can be configured in a variety of
topologies to meet the needs of specific applications and installations. Configurations
are easily changed and range from peer-to-peer networks suitable for a
6
Wireless Basics
small number of users to full infrastructure networks of thousands of users that allow
roaming over a broad area.
D-Link AirPlus Wireless Family of LAN products include:

Enhanced 2.4GHz Wireless Cardbus Adapters used with laptop
computers (DWL-650+)

Enhanced 2.4GHz Wireless PCI cards used with desktop computers
(DWL-520+)

Enhanced 2.4GHz Wireless Router and Access Point (DI-614+, DWL900AP+)
The DI-614+ is also compatible with the D-Link Air 802.11b family of products, which
include:

2.4GHz Wireless Cardbus Adapters used with laptop computers
(DWL-650)

2.4GHz Wireless PCI cards used with desktop computers (DWL-520)


Wireless Router/Access Point/Print Servers (DI-713P)
Wireless Access Points (DWL-1000AP, DWL-900AP)
Standards - Based Technology
The IEEE standard-based technology assures that the D-Link AirPlus Products are
interoperable with existing compatible 2.4GHz wireless technology. This means you
will be able to transfer large files quickly or even watch a movie in MPEG format
over your network without noticeable delays. The technology works by using multiple
frequencies in the 2.4GHz range at speeds up to 22 Mbps. D-Link AirPlus products
will automatically sense the best possible connection speed to ensure the greatest
speed and range possible with the technology.
Installation Considerations
Designed to go up to 1,312 feet (400 meters) outdoors and up to 328 feet (100
meters) indoors, the D-Link AirPlus DI-614+ lets you access your network with your
laptop computer from virtually anywhere. Keep in mind, however, that the number,
thickness and location of walls, ceilings or other objects that the wireless signals
must pass thru may limit range. Typical ranges vary depending on the types of
materials and background RF (radio frequency) noise in your home or business. The
key to maximizing range is to follow these basic guidelines:
7
Wireless Basics
1.
Keep the number of walls and ceilings between the wireless Access Point and
your receiving device (e.g., the DWL-650+) to a minimum - Each wall or ceiling
can reduce your D-Link AirPlus Wireless product’s range from 3-90 feet (1-30
meters.) Position your Access Points, Residential Gateways, and computers
so that the number of walls or ceilings is minimized.
2.
Be aware of the direct line between Access Points, Residential Gateways
(routers) and computers. A wall that is 1.5 feet thick (.5 meters), at a 45-degree
angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks
over 42 feet (14 meters) thick! Try to
make sure that the Access Points and
adapters are positioned so that the signal will travel straight through a wall or
ceiling for better reception.
3.
Building Materials make a difference - A solid metal door or aluminum studs may
have a negative effect on range. Try to position Access Points, and computers with
wireless adapters so that the signal passes through drywall or open doorways
and not other materials.
4.
Make sure that the device’s antenna is positioned for best reception by using
the software signal strength tools included with your product.
5.
Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices
or appliances that may generate extreme RF noise.
For the average home, signal range should not be an issue. If you experience low or
no signal strength in areas of your home that you wish to access, consider positioning
the Access Point in a location directly between the computers with wireless adapters.
Additional Access Points can be connected to provide better coverage in rooms where
the signal does not appear as strong as desired.
The Infrastructure Network example shown on the following page contains the following
D-Link network devices:
A wireless Broadband Router - D-Link AirPlus DI-614+
A laptop computer with a Wireless Adapter - D-Link AirPlus DWL-650+
A desktop computer with a Wireless Adapter - D-Link AirPlus DWL-520+
A Cable Modem - D-Link DCM-201
8
Getting Started
With its default settings, the DI-614+, when activated, will connect with other DLink Air or AirPlus products, right out of the box.
Networking Basics - learn how
to check and assign your IP
Address; share printers and
files.
Using the Configuration Menu
- learn the settings for the
DI-614+, using the web-based
interface.
1
2
Please refer to the following
sections of this manual for
additional information about
setting up a network:
3
4
5
For a typical network setup at home (as shown above), please do the following:
You will need broadband Internet access (a Cable or DSL subscription line
into your home or office).
Consult with your Cable or DSL provider for proper installation of the modem.
Connect the Cable or DSL modem to the DI-614+ wireless broadband router
(see the Quick Installation Guide included with the DI-614+).
If you are connecting a desktop computer to your network, you can install the
D-Link DFE-530TX+ ethernet adapter into an available PCI slot. (See the
Quick Installation Guide included with the DWL-530TX+.)
If you are connecting a laptop computer to your network, install the drivers for the Ethernet Cardbus adapter (e.g., D-Link DWL-650+) into a laptop
computer.(See the Quick Installation Guide included with the DWL-650+.)
9
Using the Configuration Menu
Whenever you want to configure your network or the DI-614+, you can access the
Configuration Menu by opening the web-browser and typing in the IP Address of the
DI-614+. The DI-614+ default IP Address is shown below:


Open the web browser
Type in the IP Address of the DI-614+
http://192.168.0.1
Note: if you have changed the default IP Address assigned to the DI-614+, make sure to enter
the correct IP Address.
The factory default User name is admin and the default
Password is blank (empty). It is recommended that you
change the admin password for security purposes. Please
refer to Tools>Admin to change the admin password.
Home > Wizard
The Home>Wizard screen will
appear. Please refer to the
Quick Installation Guide for
more information regarding
the Setup Wizard.
Apply
Cancel
Help
Clicking Apply will save changes made to the page.
Clicking Cancel will clear changes made to the page.
Clicking Help will bring up helpful information regarding the page.
Clicking Restart will restart the router. (Necessary for some changes.)
10
Using the Configuration Menu
Home > Wireless
Wireless Settings are settings for the (Access Point) Portion of the Wireless Router.
It allows you to change the wireless settings to fit an existing wireless network or to
customize your wireless network.
Enabled or Disabled By default, Wireless is Enabled. If you do not want to use the
Wireless feature on the DI-614+, you can disable it by selecting
Disabled.
SSID
Service Set Identifier (SSID) is the name designated for a specific
wireless local area network (WLAN). The SSID’s factory default
setting is “default”. The SSID can be easily changed to connect
to an existing wireless network or to establish a new wireless
network.
Channel
Indicates the channel setting for the DI-614+. By default the
channel is set to 6. The Channel can be changed to fit the
channel setting for an existing wireless network or to customize
the wireless network.
Auto Scan
Click the check box to enable Auto Scan. Enabling this will allow
the device to detect the best wireless channel to use.
11
Using the Configuration Menu
Home > Wireless (Continued)
WEP
Wired Equivalent Protocol (WEP) is a wireless security protocol
for Wireless Local Area Networks (WLAN). WEP provides security
by encrypting the data that is sent over the WLAN. The DI-614+
supports 3 levels of WEP Encryption: 64Bit encryption, 128Bit
encryption, and 256Bit encryption. WEP is disabled by default. The
WEP setting can be changed to fit an existing wireless network
or to customize your wireless network.
Shared Key
In this mode, in order to access the DI-614+ on the network, the
device must be listed in the MAC Address Control List.
Open System
The DI-614+ will be visible to all devices on the network. This is
the default setting.
The Key Types that are supported by the DI-614+ are HEX
(Hexadecimal) and ASCII (American Standard Code for
Information Interchange.) The Key Type can be changed to
fit an existing wireless network or to customize your wireless
network.
Key Type
KEYS
Keys 1-4 allow you to easily change wireless encryption settings
to maintain a secure network. Simply select the specific key to be
used for encrypting wireless data on the network.
12
Using the Configuration Menu
Home > Wireless > WPA
Wi-Fi Protected Access authorizes and authenticates users onto the wireless network.
WPA uses stronger security than WEP and is based on a key that changes automatically
at a regular interval. This mode requires a RADIUS server in the network.
Radius Server 1
IP - Enter the IP Address of the RADIUS server.
Port - Enter the port number that your RADIUS server uses for
Authentication. The default setting of 1812 is the port setting
for many RADIUS servers.
Shared Secret - Enter the Shared Secret. The Shared Secret must
be the same as the Shared Secret on your RADIUS server.
Radius Server 2
Optional. If you have a second RADIUS server, you will
input the same information as shown above.
13
Using the Configuration Menu
Home > Wireless > WPA-PSK
Wi-Fi Protected Access - Pre-Shared Key mode means that the wireless client and the
router must have the same passphrase in order to establish the wireless connection. A
RADIUS server is not required with PSK.
Passphrase
Enter a passphrase for the router. The RADIUS server should
use the same passphrase (secret key) as the router.
Confirmed PassphraseEnter the Passphrase again to confirm.
14
Using the Configuration Menu
Home > WAN
Choose WAN Type
WAN stands for Wide Area Network. In this case WAN represents the mode in which you
connect to the Internet. If you are uncertain, please ask your ISP which of the following
represents your connection mode to the Internet:
Dynamic
IP Address
Obtain an IP address from your ISP automatically (mainly for
Cable users).
Static IP
Address
Your ISP assigns you a Static IP Address.
PPP over Ethernet
Some ISPs require the use of PPPoE to connect to their services
(mainly for DSL users).
Others
PPTP
For use in Europe only.
L2TP
For specific ISP’s use only.
Big Pond
Cable
For use in Australia only.
15
Using the Configuration Menu
Home > WAN > Dynamic IP Address
Most Cable modem users will select this option to obtain an IP Address automatically
from their ISP (Internet Service Provider).
Host Name
This is optional, but may be required by some ISPs. The host
name is the device name of the Router.
MAC Address
The default MAC Address is set to the WAN’s physical interface
MAC address on the Router.
Clone
MAC Address
This feature will copy the MAC address of the Ethernet card, and
replace the WAN MAC address of the Router with this Ethernet
card MAC address. It is not recommended that you change the
default MAC address unless required by your ISP.
Primary DNS
Address
Input the primary DNS address provided by your ISP
Secondary DNS
Address
(Optional) Input the Secondary DNS address provided by your
ISP.
MTU
Maximum Transmission Unit; default is 1500; you may need to
change the MTU to conform to your ISP.
16
Using the Configuration Menu
Home > WAN > Static IP Address
Choose Static IP Address if all WAN IP information is provided to you by your ISP. You will
need to enter in the IP address, subnet mask, gateway address, and DNS address(es)
provided to you by your ISP. Each IP address entered in the fields must be in the
appropriate IP form, which are four IP octets separated by a dot (x.x.x.x). The Router
will not accept the IP address if it is not in this format.
IP Address
Input the IP Address provided by your ISP.
Subnet Mask
Input the Subnet Mask provided by your ISP.
ISP Gateway
Input the Gateway address provided by your ISP.
MAC Address
The default MAC Address is set to the WAN’s physical interface
MAC address on the Router.
Clone
MAC Address
This feature will copy the MAC address of the Ethernet card, and
replace the WAN MAC address of the Router with this Ethernet
card MAC address. It is not recommended that you change the
default MAC address unless required by your ISP.
Primary DNS
Address
Input the primary DNS address provided by your ISP.
Secondary DNS
Address
(Optional) Input the Secondary DNS address provided by
your ISP.
MTU
Maximum Transmission Unit; default is 1500; you may need to
change the MTU to conform to your ISP.
17
Using the Configuration Menu
Home > WAN > PPPoE
Most DSL users will select this option to obtain an IP address automatically from their
ISP through the use of PPPoE.
Your PPPoE username provided by your ISP.
User Name
Password
Your PPPoE password is provided by your ISP.
Service Name
(Optional) Check with your ISP for more information if they require
the use of service name.
IP Address
(Optional) Enter in the IP Address if you are assigned a static
PPPoE address.
MAC Address
The default MAC Address is set to the WAN’s physical interface
MAC address on the Router.
Clone
MAC Address
This feature will copy the MAC address of the Ethernet card, and
replace the WAN MAC address of the Router with this Ethernet
card MAC address. It is not recommended that you change the
default MAC address unless required by your ISP.
18
Using the Configuration Menu
Home > WAN > PPPoE (Continued)
Primary DNS
Address
You will get the DNS IP automatically from your ISP but you
may enter a specific DNS address that you want to use instead.
Secondary DNS
Address
(Optional) Input the secondary DNS address.
Maximum
Idle Time
Enter a maximum idle time during which Internet connection
is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
MTU
Maximum Transmission Unit; default is 1492; you may need to
change the MTU to conform to your ISP.
Auto-reconnect
If enabled, the Broadband Router will automatically connect to
your ISP after your system is restarted or if the connection is
dropped.
19
Using the Configuration Menu
Home > WAN > PPTP
Point-to-Point Tunneling Protocol (PPTP) is a WAN connection used in Europe.
IP Address
Enter the IP Address.
Subnet Mask
Enter the Subnet Mask.
Server IP
Enter the Server IP Address.
PPTP Account
Enter the PPTP account name.
PPTP Password
Enter the PPTP password.
Maximum
Idle Time
Enter a maximum idle time during which Internet connection
is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
MTU
Maximum Transmission Unit; default is 1400; you may need to
change the MTU to conform to your ISP.
Auto-reconnect
If enabled, the Broadband Router will automatically connect
to your ISP after your system is restarted or if the connection
is dropped.
20
Using the Configuration Menu
Home > WAN > L2TP
Layer 2 Tunneling Protocol (L2TP) is a WAN connection.
IP Address
Enter the IP Address.
Subnet Mask
Enter the Subnet Mask.
Server IP
Enter the Server IP Address.
L2TP Account
Enter the PPTP account name.
L2TP Password
Enter the PPTP password.
Maximum
Idle Time
Enter a maximum idle time during which Internet connection
is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
MTU
Maximum Transmission Unit; default is 1400; you may need to
change the MTU to conform to your ISP.
Auto-reconnect
If enabled, the Broadband Router will automatically connect
to your ISP after your system is restarted or if the connection
is dropped.
21
Using the Configuration Menu
Home > WAN > BigPond Cable
Dynamic IP Address for BigPond is a WAN connection used in Australia.
User Name
Enter in the username for the BigPond account.
Password
Enter the password for the BigPond account.
Auth Server
Select the auth server for the BigPond account.
Login Server IP
(Optional) Enter the Login Server name if required.
MAC Address
The default MAC Address is set to the WAN’s physical interface
MAC address on the Router.
Clone
MAC Address
This feature will copy the MAC address of the Ethernet card, and
replace the WAN MAC address of the Router with this Ethernet
card MAC address. It is not recommended that you change the
default MAC address unless required by your ISP.
22
Using the Configuration Menu
Home > LAN
LAN is short for Local Area Network. This is considered your internal network. These are
the IP settings of the LAN interface for the DI-614+. These settings may be referred to
as Private settings. You may change the LAN IP address if needed. The LAN IP address
is private to your internal network and cannot be seen on the Internet.
IP Address
The IP address of the LAN interface.
The default IP address is: 192.168.0.1.
Subnet Mask
The subnet mask of the LAN interface.
The default subnet mask is 255.255.255.0.
Local Domain Name
(Optional) The name of your local domain.
DNS Relay
You may choose to enable or disable DNS Relay. If disabled,
the DNS address received on the WAN port will pass through
to the LAN clients.
23
Using the Configuration Menu
Home > DHCP
DHCP stands for Dynamic Host
Control Protocol. The DI-614+
has a built-in DHCP server. The
DHCP Server will automatically
assign an IP address to the
computers on the LAN/private
network. Be sure to set your
computers to be DHCP clients
by setting their TCP/IP settings
to “Obtain an IP Address
Automatically.” When you turn
your computers on, they will
automatically load the proper
TCP/IP settings provided by
the DI-614+. The DHCP Server
will automatically allocate an
unused IP address from the IP
address pool to the requesting
computer. You must specify the
starting and ending address of
the IP address pool.
DHCP Server
Enable or disable the DHCP service.
Starting IP Address
The starting IP address for the DHCP server’s IP assignment.
Ending IP Address
The ending IP address for the DHCP server’s IP assignment.
Lease Time
The length of time for the DHCP lease.
Static DHCP
Used to allow the DHCP server to assign the same IP adress to
a specific MAC address. Enter the name, IP address, and MAC
address into the fields. Select which DHCP client to clone.
Name
The name to be used to reference the specific static DHCP
client.
MAC Address
The MAC address of the static DHCP client.
DHCP Client
Drop down list of all currently connected DHCP clients.
DHCP Clients List
Lists the DHCP clients connected to the DI-614+. Click Refresh
to update the list. The table will show the Host Name, IP Address,
and MAC Address of the DHCP client computer.
24
Using the Configuration Menu
Advanced > Virtual Server
The DI-614+ can be configured as a virtual server so that remote users accessing
Web or FTP services via the public IP address can be automatically redirected to local
servers in the LAN (Local Area Network).
The DI-614+ firewall feature filters out unrecognized packets to protect your LAN network
so all computers networked with the DI-614+ are invisible to the outside world. If you
wish, you can make some of the LAN computers accessible from the Internet by enabling
Virtual Server. Depending on the requested service, the DI-614+ redirects the external
service request to the appropriate server within the LAN network.
Enable
Select to activate the policy.
Name
Private IP
You can name the Virtual Server.
The IP address of the internal computer that will be using the
virtual service.
Protocol Type
Select the protocol the Virtual Server will use.
Private/ Public Ports
Enter in the private and public port or ports to be used. A range
of ports can be specified with a hyphen. (e.g., 20-21)
Schedule
Select Always, or choose From and enter the time period during
which the virtual service will be available.
25
Using the Configuration Menu
Advanced > Applications
Some applications require multiple connections, such as Internet gaming, video
conferencing, and Internet telephony. These applications have difficulties working
through NAT (Network Address Translation). Special Applications makes some of these
applications work with the DI-614+. If you need to run applications that require multiple
connections, specify the port normally associated with an application in the Trigger
field, then enter the public ports associated with the trigger port into the Incoming Ports
field.
At the bottom of the screen, there are already defined special applications. To use them,
select one from the drop down list and select an ID number you want to use. Then click
the “Copy to” button and the router will fill in the appropriate information to the list. You
will then need to enable the service. If the mechanism of Special Applications fails to
make an application work, try using DMZ host instead.
Note! Only one PC can use each Special Application tunnel.
Enabled or
Select to activate or deactivate the policy.
Disabled
Name
You can name the defined special applications.
Trigger Port
This is the port used to trigger the application. It can be either
a single port or a range of ports.
Trigger Type
Public Ports
Select the trigger protocol you would like to initiate. To chage
the selection, use the drop down arrow and other choices will
be listed.
This is the port number on the WAN side that will be used to
access the application. You may define a single port or a range
of ports. You can use a comma to add multiple ports or port
ranges.
Public Type
Select the public type the special application will use.
26
Using the Configuration Menu
Advanced > Filters > IP Filter
Use IP (Internet Protocol) filters to allow or deny computers access to the Internet
based on their IP address.
Enabled or Disabled
Click Enabled to apply the filter policy or click Disabled to enter
an inactive filter policy. (You can reactivate the policy later.)
IP Address
Enter the IP address range of the computers that you want the
policy to apply to. If it is only a single computer that you want
the policy applied to, then enter the IP address of the computer
in the Start Source IP and leave the End Source IP blank.
Port Range
Enter in the port range of the TCP/UDP ports that you want
the policy to apply to. If it is only a single port that you want the
policy applied to, then enter the port number in the Start Port
field and leave the End Port field blank. If you want to use all
the ports, you can leave the port range empty.
Protocol Type
Select the protocol type to allow or deny certain types of IP
addresses.
Schedule
Select Always, or choose From and enter the time period during
which the IP filter policy will be in effect.
27
Using the Configuration Menu
Advanced > Filters > MAC Filters
MAC (Media Access Control) Filters are used to deny or allow LAN (Local Area Network)
computers from accessing the Internet and network by their MAC address.
At the bottom of the screen, there is a list of MAC addresses from the DHCP client
computers connected to the DI-614+. To use them, select one from the drop down
list and select an IP number you want to use. Then click the “Copy to” button and the
DI-614+ will fill in the appropriate information in the list.
Disabled MAC Filter
Select this option if you do not want to use MAC filters.
Only allow computers with MAC address listed below to access the network
Select this option to only allow computers that are in the list
to access the network and Internet. All other computers will
be denied access to the network and Internet.
Only deny computers with MAC address listed below to access the network
Select this option to only deny computers that are in the list
to access the network and Internet. All other computers will
be allowed access to the network and Internet.
Name
Enter a name to create a profile for the associated
computer(s) on the network.
MAC Address
Enter the MAC Address of the client that will be filtered.
DHCP Client
Select from the DHCP Client list and click the Clone button to
automatically clone that computer’s MAC address to the MAC
address field.
28
Using the Configuration Menu
Advanced > Parental Control >URL Blocking
Use URL Blocking to deny LAN computers from accessing specific web sites by its
URL. A URL is a specially formatted text string that defines a location on the Internet.
If any part of the URL contains the blocked word, the site will not be accessible and
the web page will not display.
Disabled URL Blocking
Select this option if you do not want to use URL Blocking.
29
Using the Configuration Menu
Advanced > Parental Control > Domain Blocking
Use Domain filters to allow or deny computers access to specific Internet domains
whether it is through www, ftp, SNMP, etc. Domain filters apply to both wired computers
connected to one of the four Ethernet LAN ports and to wireless clients connected
wirelessly to the DI-614+.
Disabled Domain Filter Select this option if you do not want to use Domain filters.
Allow users to access the following domains and block all other domains
Select this option to allow users to access the specified
Internet domains listed below. Users will be denied access
to all other Internet domains.
Deny users to access the following domains and permit all other domains
Select this option to deny users access to the specified
Internet domains listed below. Users will be allowed access
to all other Internet domains.
Permitted/Blocked Domains
This is a list of domain suffixes of the Internet domain you
want to permit or block. (Example: shopping.com,
sports.net.)
30
Using the Configuration Menu
Advanced > Firewall
Firewall Rules is an advance feature used to deny or allow traffic from passing
through the device. It works in the same way as IP Filters with additional settings. You
can create more detailed rules for the device.
Enabled or Disabled
Click Enabled to apply the filter policy or click Disabled to enter an inactive filter policy
(You can reactivate the policy later).
Name
Enter the name of the Firewall Rule.
Action
Select Allow or Deny to allow or deny traffic to pass through the DI-614+.
Interface Source
Choose between a LAN or WAN source. An asterisk signifies the selection of both
sources.
Interface Destination
Choose between a LAN or WAN destination. An asterisk signifies the selection of both
destinations.
IP Start
The starting IP address for the filter policy. Leaving the field blank selects all IPs.
IP End
The ending IP address for the filter policy. Leaving the field blank sleects all IPs.
31
Using the Configuration Menu
Advanced > Firewall (Continued)
Protocol
Select one of the following protocols: TCP, UDP, or ICMP.
Port Range
Enter in the port range of the TCP/UDP ports that you want the policy to apply to. If it
is only a single port that you want the policy applied to, then enter the port number in
the Start Port field and leave the End Port field blank. If you want to use all the ports,
you can leave the port range empty.
Schedule
Select Always, or choose From and enter the time period during which the virtual service
will be available
32
Using the Configuration Menu
Advanced > DMZ
If you have a computer that cannot run Internet applications properly from behind the
DI-614+, then you can allow that computer to have unrestricted Internet access. Enter
the IP address of that computer as a DMZ (Demilitarized Zone) host with unrestricted
Internet access. Adding a client to the DMZ may expose that computer to a variety of
security risks, so only use this option as a last resort.
33
Using the Configuration Menu
Advanced > Performance
Beacon Interval
Beacons are packets sent by an Access Point to synchronize a
wireless network. Specify a value. 100 is the default setting and is
recommended.
DTIM interval
(Delivery Traffic Indication Message) 3 is the default setting. A DTIM
is a countdown informing clients of the next window for listening to
broadcast and multicast messages.
Basic Rates
Select the data rate. Default is 1-2-5.5-11-22Mbps.
TX Rates
Select the data rate. Default is 1-2-5.5-11-22Mbps.
Preamble Type
Long preamble is the default setting. (High traffic networks should
use the shorter preamble type.) The preamble defines the length of
the CRC block used in communication between the Access Point
and the roaming wireless Network adapters.(Cyclic Redundancy
Check is a common technique for detecting data transmission
errors)
34
Using the Configuration Menu
Advanced > Performance (Continued)
SSID Broadcast
Enabled is the default setting. Choose Enabled to broadcast
the SSID across the network. All devices on a network must
share the same SSID (Service Set Identifier) to establish
communication. Choose Disabled if you do not wish to
broadcast the SSID over the network.
Antenna transmit
power
The DI-614+ has the option to adjust its wireless transmit power.
Limiting transmit power can help in situations where you do not
want the same signals overlapping one another.
Antenna Selection
Select Internal Antenna, External Antenna, or Diversity Antenna.
Internal
In this mode, the DI-614+ only uses the internal antenna for
short distance coverage.
External
In this mode, the DI-614+ only uses the external antenna and
extends wireless coverage.
In this mode, the DI-614+ uses both the internal and external
antenna and then uses the antenna that picks up the strongest
signal.
Diversity
4X Mode
4x Mode allows for higher speed wireless performance. Only
other devices that support 4x Mode will be able to take advantage of the higher performance.
35
Using the Configuration Menu
Tools> Admin
There are two accounts that can access the Broadband Router’s Web-Management
interface. They are admin and user. Admin has read/write access while user has readonly access. User can only view the settings but cannot make any changes. It is recommended that you change the admin password from the default setting. The default
password is blank (no password).
Password
To change the admin and user passwords, enter in the old
password, and enter the new password twice to confirm.
Remote
Management
Remote Management allows the device to be configured
through the WAN (Wide Area Network) port from the Internet
using a web browser. A username and password is still required
to access the browser-based management interface.
IP Address
Internet IP Address of the computer that has access to the
DI-614+. If the IP Address is set to 0.0.0.0, this allows all Internet
IP addresses to access the DI-614+.
Port
The port number used to access the DI-614+.
E.g., http://x.x.x.x:80, where x.x.x.x. is the WAN IP address of
the DI-614+ and 80 is the port used for the Web Management
interface.
36
Using the Configuration Menu
Tools> Time
Set the time here by entering it manually or by using NTP (Network Time Protocol.) NTP
is a standard protocol on the Internet that sychronizes the time settings accurately for
all the computers on your network.
Time Zone
Select your time zone from the pull-down menu.
Daylight Saving
Select to enable or disable Daylight Saving. If you choose to
enable this, enter the start and end date and the system time
will automatically adjust on those dates
Default NTP Server
(Optional.) If you are enabling NTP to synchronize the time
settings on your network using an NTP server, please enter
the link to the default server.
Set Device Date and
Time
If you are entering the time manually, select the correct Year,
Month, Day, Hour, Minute, and Second.
37
Using the Configuration Menu
Tools > System
The current system settings can be saved as a file onto the local hard drive. The saved
file or any other saved setting file created by the DI-614+ can be uploaded to the unit.
To reload a system settings file, click on Browse to search the local hard drive for the
file to be used. The device can also be reset back to factory default settings by clicking
on the Reset to Default button. Use the restore feature only if necessary. This will erase
previously saved settings for the unit. Make sure to save your system settings to the
hard drive before doing a factory restore.
Save Settings to
Local Hard Drive
Click Backup Setting to save the current settings to the local
Hard Drive.
Load Settings from
Local Hard Drive
Click Browse to find the settings file, then click Load.
Restore to Factory
Default Settings
Click Reset to Default to restore the factory default settings.
38
Using the Configuration Menu
Tools > Firmware
You can upgrade the firmware by using this tool. First, check the D-Link support site for
firmware updates at http://support.dlink.com. Make sure that the firmware you want to
use is saved on the local hard drive of your computer. Click on Browse to search the local
hard drive for the firmware that you downloaded from the D-Link website to be used for
the update. Upgrading the firmware will not change any of your system settings but it is
recommended that you save your system settings before doing a firmware upgrade.
Browse
After you have downloaded the new firmware, click Browse in
this window to locate the firmware update on your hard drive.
Click Apply to complete the firmware upgrade.
Note: Do not power off the unit when it is being upgraded. When the
upgrade is complete, the unit will automatically restart.
39
Using the Configuration Menu
Tools >DDNS
DDNS (Dynamic Domain Name System) keeps dynamic IP addresses (e.g., IP
addresses assigned by a DHCP capable router or server) linked to a domain name.
Users who have a Dynamic DNS account may use this feature on the DI-614+.
DDNS
When an IP address is automatically assigned by a DHCP
server, DDNS automatically updates the DNS server. Select
Disabled or Enabled.
Server Address
Select from the pull-down menu.
Host Name
Enter the Host name.
Username
Enter the username.
Password
Enter the password.
40
Using the Configuration Menu
Tools > Misc
41
Using the Configuration Menu
Tools > Misc (Continued)
Ping Test
This useful diagnostic utility can be used to check if a
computer is on the Internet. It sends ping packets and
listens for replies from the specific host.
Restart Device
Click reboot to restart the unit.
Block WAN Ping
Click Enable to block the WAN ping. Computers on the
Internet will not get a reply back from the DI-614+ when it
is being “ping”ed. This may help to increase security.
UPnP Setting
Universal Plug and Play is a feature that is preset to allow
certain popular applications such as MSN messenger to be
functional using the router without making any configurations. By default UPnP setting is set to enable. It is recommended to keep UPnP Setting on enable.
Gaming Mode
Click Enable to enable Gaming Mode. This feature allows
many online games to work with the DI-614+.
VPN Pass Through
For users who telecommute or use Virtual Private Network
(VPN), you can select PPTP or IPSec to be used with this
router.
WAN select to 10/100
Mbps
This option allows the user to select 10Mbps, 100 Mbps,
or 10/100Mbps Auto for the WAN port. You may need to
change the WAN port speed if you are experiencing
connection problems with your Cable or DSL modem.
42
Using the Configuration Menu
Tools > Cable Test
Diagnostic Cable Tester is an advanced feature that integrates a LAN cable tester on
every Ethernet port on the router. Through the graphical user interface (GUI), Cable
Tester can be used to remotely diagnose and report cable faults such as opens,
shorts, swaps, and impedance mismatch. The Cable Tester feature significantly
reduces service calls and returns by allowing users to easily troubleshoot their cable
connections.
Ports
The Ethernet port names associated to the physical ports.
Link Status
The current link status of the Ethernet cable connected to the
respective Ethernet port.
More Info
Click on More Info for
detailed information
about the cable link
status. The following
window will appear.
Refresh
Click on Refresh to run the cable test. Allow the router a few
seconds to complete the test.
43
Using the Configuration Menu
Status > Device Info
This screen displays information about the DI-614+.
DHCP Release
Click to release IP addresses sent from the DHCP server.
DHCP Renew
Click to renew IP addreses sent from the DHCP server.
44
Using the Configuration Menu
Status > Log
This screen displays activities occurring on the DI-614+.
First Page-
Click First Page to go to the first page of the log.
Last Page-
Click Last Page to go to the last page of the log.
Previous-
Click Previous to go to the previous page of the log.
Next-
Click Next to go to the next page of the log.
Clear-
Click Clear to clear the log.
Log Settings-
Click for advanced features (see next page.)
45
Using the Configuration Menu
Status > Log > Log Settings
E-Mail Alert
The DI-614+ can be set up to send the log files to a specific
email address.
SMTP Server IP
Enter in the IP address of the mail server.
Email Address
Enter in the email address of the recipient who will receive
the email log.
Send Mail Now
Click to send mail immediately.
Save Log File to Local Hard Drive
Selecting this allows you to save the log to a local hard drive.
A window will appear prompting you to save the file to a specific location.
Log Type
Select the types of activity to log.
46
Using the Configuration Menu
Status > Stats
In Stats section, traffic statistics are displayed.
Refresh
This will update the page.
Reset
This will reset the packet counter to zero.
WAN
Displays Received / Transmitted packets from the WAN port.
LAN
Displays Received / Transmitted packets from the LAN port.
WIRELESS
Displays received and transmitted packets from the wireless
network.
47
Using the Configuration Menu
Status > Wireless
The wireless client table displays a list of current connected wireless clients. This
table also displays the time and MAC address of the wireless client connected.
48
Using the Configuration Menu
Help
This screen displays the complete Help menu. For help at anytime, click the Help tab
in the Configuration menu.
49
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and
operation of the DI-614+ Wireless Access Point. We cover various aspects of the
network setup, including the network adapters. Please read the following if you are
having problems.
(Note: It is recommended that you use an Ethernet connection to configure the DI-614+
Access Point.)
1. The computer used to configure the DI-614+ cannot access the
Configuration menu.

Check that the Ethernet LED on the DI-614+ is ON. If the LED is not
ON, check that the cable for the Ethernet connection is securely
inserted.

Check that the Ethernet Adapter is working properly. Please see
item 6 (Check that the drivers for the network adapters are installed
properly) in this Troubleshooting section to check that the drivers are
loaded properly.

Check that the IP Address is in the same range and subnet as the
DI-614+. Please see Checking the IP Address in Windows XP in the
Networking Basics section of this manual.
Note: The IP Address of the DI-614+ is 192.168.0.1. All the computers on the network
must have a unique IP Address in the same range, e.g., 192.168.0.x. and a Subnet Mask
of 255.255.255.0. Any computers that have identical IP Addresses will not be visible on the
network.

Do a Ping test to make sure that the DI-614+ is responding. Go to
Start>Run>Type Command>Type ping 192.168.0.1. A successful ping
will show four replies.
50
Troubleshooting
2. The wireless client cannot access the Internet in the Infrastructure mode.

Make sure the wireless client is associated and joined with the
correct router. To check this connection: Right-click on the Local Area
Connection icon in the taskbar> select View Available Wireless Networks.
The Connect to Wireless Network screen will appear. Please make
sure you have selected the correct available network, as shown in
the illustrations below.
Default


Check that the IP Address assigned to the wireless adapter is within the
same IP Address range as the gateway. (Since the DI-614+ has an IP
Address of 192.168.0.1, wireless adapters must have an IP Address in
the same range, e.g., 192.168.0.x. Each device must have a unique IP
Address; no two devices may have the same IP Address. The subnet
mask must be the same for all the computers on the network.) To
check the IP Address assigned to the wireless adapter, double-click on
the Local Area Connection icon in the taskbar > select the Support tab
and the IP Address will be displayed. (Please refer to Checking the IP
Address in the Networking Basics section of this manual.)
If it is necessary to assign a Static IP Address to the wireless adapter,
please refer to the appropriate section in Networking Basics. If you are
entering a DNS Server address you must also enter the Default Gateway
Address. (Remember that if you have a DHCP-capable router, you
will not need to assign a Static IP Address. See Networking Basics:
Assigning a Static IP Address.)
51
Troubleshooting
3. Check that the drivers for the network adapters are installed properly.
You may be using different network adapters than those illustrated here, but this
procedure will remain the same, regardless of the type of network adapters you are
using.


Go to Start.

Click Properties.
Right-click on My
Computer.
NOTE: Screen shots taken using
Windows XP. If you are using a
different Operating System your
screen may look different.


Select the Hardware Tab.
Click Device Manager.
52
Troubleshooting

Double-click on Network
Adapters.

Right-click on D-Link AirPlus
DWL-650+ Wireless Cardbus
Adapter.

Select Properties to check
that the drivers are installed
properly.
D-Link AirPlus DWL-650+ Wireless Cardbus

Look under Device Status to
check that the device is working
properly.

Click OK.
53
Troubleshooting
4. Resetting the DI-614+ to Factory Default Settings
After you have tried other methods for troubleshooting your network, you
may choose to Reset the DI-614+ to the factory default settings. Remember
that D-Link AirPlus products network together, out of the box, at the factory
default settings.
To hard-reset the D-Link AirPlus DI-614+ to Factory Default Settings, please do the
following:

Locate the Reset button on the back of the DI-614+.

Use a paper clip to press the Reset button.
 Hold for about 10 seconds and then release.

After the DI-614+ reboots (this may take a few minutes) it will
be reset to the factory Default settings.
54
Networking Basics
Using the Network Setup Wizard in Windows XP
In this section you will learn how to establish a network at home or work,
using Microsoft Windows XP.
Note: Please refer to websites such as http://www.homenethelp.com
and http://www.microsoft.com/windows2000 for information about networking
computers using Windows 2000, Me or 98.
Go to Start>Control Panel>Network Connections
Select Set up a home or small office network
When this screen appears, Click Next.
55
Networking Basics
Please follow all the instructions in this window:
Click Next.
In the following window, select the description that best fits your computer. If
your computer connects to the internet through a gateway/router, select the
second option as shown.
Click Next.
56
Networking Basics
Enter a Computer description and a Computer name (optional).
Click Next.
Enter a Workgroup name. All computers on your network should have the same
Workgroup name.
Click Next.
57
Networking Basics
Please wait while the Network Setup Wizard applies the changes.
When the changes are complete, click Next.
Please wait while the Network Setup Wizard configures the computer.
This may take a few minutes.
58
Networking Basics
In the window below, select the option that fits your needs. In this example, Create a
Network Setup Disk has been selected. You will run this disk on each of the computers
on your network. Click Next.
Insert a disk into the Floppy Disk Drive, in this case drive A.
59
Networking Basics
Please read the information under Here’s how in the screen below. After you complete
the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup
Wizard once on each of the computers on your network. To continue click Next.
60
Networking Basics
Please read the information on this screen, then click Finish to complete the Network
Setup Wizard.
The new settings will take effect when you restart the computer. Click Yes to
restart the computer.
You have completed configuring this computer. Next, you will need to run the
Network Setup Disk on all the other computers on your network. After running
the Network Setup Disk on all your computers, your new wireless network will
be ready to use.
61
Networking Basics
Naming your Computer
To name your computer, please follow these directions. In Windows XP:
 Click Start (in the lower left corner of the screen).

Right-click on My Computer.

Select Properties and click.
 Select the Computer Name
Tab in the System Properties window.
 You may enter a Computer
Description if you wish; this
field is optional.
 To rename the computer
and join a domain, Click
Change.
62
Networking Basics
Naming your Computer
 In this window, enter the
Computer name.
 Select Workgroup and enter the
name of the Workgroup.
 All computers on your network
must have the same Workgroup
name.
 Click OK.
OK
Assigning a Static IP Address in Windows XP/2000
Note: Residential Gateways/Broadband Routers will automatically assign IP Addresses to
the computers on the network, using DHCP (Dynamic Host Configuration Protocol) technology. If you are using a DHCP-capable Gateway/Router you will not need to assign Static IP
Addresses.
If you are not using a DHCP capable Gateway/Router, or you need to assign a Static
IP Address, please follow these instructions:

Go to Start.

Double-click on
Control Panel.
63
Networking Basics
Assigning a Static IP Address in Windows XP/2000
 Double-click
on Network
Connections.
 Right-click on Local Area
Connections.
 Double-click on
Properties.
64
Networking Basics
Assigning a Static IP Address
in Windows XP/2000
 Click on Internet
Protocol (TCP/IP).
 Click Properties.
Enter the LAN IP address of
the Wireless Router. (D-Link
wireless routers have a LAN IP
address of 192.168.0.1.)
The DNS server information will
be supplied by your ISP (Internet
Service Provider).
Click OK
192 168
0
1
192 168
0
1
65
Networking Basics
Assigning a Static IP Address with Macintosh OSX
 Go to the Apple Menu and select
System Preferences.
 cClick on Network.
 Select Built-in Ethernet in the
Show pull-down menu.
 Select Manually in the Configure
pull-down menu.
 Input the Static IP Address,
the Subnet Mask, and the
Router IP Address in the
appropriate fields.
 Click Apply Now.
66
Networking Basics
Selecting a Dynamic IP Address with Macintosh OSX
 Go to the Apple Menu and select
System Preferences.
 Click on Network.
 Select Built-in Ethernet in the
Show pull-down menu.
 Select Using DHCP in the Configure pull-down menu.
 Click Apply Now.
 The IP Address, Subnet mask,
and the Router’s IP Address will
appear in a few seconds.
67
Technical Specifications
Standards
 IEEE 802.3 10BASE-T Ethernet
 IEEE 802.3u 100BASE-TX Fast Ethernet
 IEEE 802.11b
VPN Pass Through Function
 PPTP
 IPSec
Advanced Firewall Features
Device Management
 Web-Based – Internet Explorer 6.0 or later; Netscape Navigator 6 or
later; or other Java- enabled browsers.
Wireless Data Rates* With Automatic Fallback





22Mbps
11Mbps
5.5Mbps
2Mbps
1Mbps
Encryption
 64/128/256-bit RC4
Media Access Control
 CMSA/CA with ACK
Wireless Frequency Range
 2.4GHz to 2.46GHz
Wireless Operating Range
 Indoors: Up to 328 feet (100 meters)
 Outdoors: Up to 1,312 feet (400 meters)
Wireless Modulation Technology
 PBCC - Packet Binary Convolutional Coding
 DSSS - Direct Sequence Spread Spectrum
 11-chip Barker sequence
* Maximum wireless signal rate derived from IEEE Standard 802.11b specifications. Actual data throughput
will vary. Network conditions and environmental factors, including volume of traffic, building materials and
construction, and network overhead lower actual data throughput rate.
68
Technical Specifications
Modulation Technique







Barker (1Mbps/0db)
Barker (2Mbps/3db)
CCK (5.5Mbps/5.5db)
PBCC (5.5Mbps/1.4db)
CCK (11Mbps/8.6db)
PBCC (11Mbps/4.5db)
PBCC (22Mbps/8.5db)
Wireless Transmit Power
 15dBm ± 2dB
External Antenna Type
 Single detachable reverse SMA
LEDs






Power
M1
M2
WAN
Local Network - 10/100
WLAN (Wireless Connection)
Operating Temperature
 32°F to 131°F ( 0°C to 55°C)
Humidity
 95% maximum (non-condensing)
Power
 DC 5V 2.5A
Safety & Emissions
 FCC
 UL
Dimensions
 L = 7.56 inches (192mm)
 W = 4.65 inches (118mm)
 H = 1.22 inches (31mm)
Weight
 ~10.8 oz. (0.3kg)
69
Technical Support
You can find software updates and user documentation on the D-Link website.
D-Link provides free technical support for customers within the United States and
within Canada for the duration of the warranty period on this product.
U.S. and Canadian customers can contact D-Link technical support through our
website, or by phone.
Tech Support for customers within the United States:
D-Link Technical Support over the Telephone:
(877) 453-5465
24 hours a day, seven days a week.
D-Link Technical Support over the Internet:
http://support.dlink.com
email:[email protected]
Tech Support for customers within Canada:
D-Link Technical Support over the Telephone:
(800) 361-5265
Monday to Friday 7:30am to 12:00am EST
D-Link Technical Support over the Internet:
http://support.dlink.ca
email:[email protected]
70
Warranty
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited
warranty for its product only to the person or entity that originally purchased the product from:
 D-Link or its authorized reseller or distributor and
 Products purchased and delivered within the fifty states of the United States, the District of Columbia,
U.S. Possessions or Protectorates, U.S. Military Installations, addresses with an APO or FPO.
Limited Warranty: D-Link warrants that the hardware portion of the D-Link products described below will
be free from material defects in workmanship and materials from the date of original retail purchase of the
product, for the period set forth below applicable to the product type (“Warranty Period”), except as otherwise
stated herein.
3-Year Limited Warranty for the Product(s) is defined as follows:



Hardware (excluding power supplies and fans) Three (3) Years
Power Supplies and Fans One (1) Year
Spare parts and spare kits Ninety (90) days
D-Link’s sole obligation shall be to repair or replace the defective Hardware during the Warranty Period at
no charge to the original owner or to refund at D-Link’s sole discretion. Such repair or replacement will be
rendered by D-Link at an Authorized D-Link Service Office. The replacement Hardware need not be new or
have an identical make, model or part. D-Link may in its sole discretion replace the defective Hardware (or
any part thereof) with any reconditioned product that D-Link reasonably determines is substantially equivalent
(or superior) in all material respects to the defective Hardware. Repaired or replacement Hardware will be
warranted for the remainder of the original Warranty Period from the date of original retail purchase. If a
material defect is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to
repair or replace the defective Hardware, the price paid by the original purchaser for the defective Hardware
will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware (or part thereof)
that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link
upon replacement or refund.
Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially
conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable
documentation, from the date of original retail purchase of the Software for a period of ninety (90) days
(“Warranty Period”), provided that the Software is properly installed on approved hardware and operated as
contemplated in its documentation. D-Link further warrants that, during the Warranty Period, the magnetic
media on which D-Link delivers the Software will be free of physical defects. D-Link’s sole obligation shall
be to replace the non-conforming Software (or defective media) with software that substantially conforms
to D-Link’s functional specifications for the Software or to refund at D-Link’s sole discretion. Except as
otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee,
and is subject to the terms and conditions of the license granted by D-Link for the Software. Software will
be warranted for the remainder of the original Warranty Period from the date or original retail purchase. If
a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it
is not practical to replace the non-conforming Software, the price paid by the original licensee for the nonconforming Software will be refunded by D-Link; provided that the non-conforming Software (and all copies
thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given
automatically terminates.
Non-Applicability of Warranty: The Limited Warranty provided hereunder for hardware and software of DLink’s products will not be applied to and does not cover any refurbished product and any product purchased
through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or the liquidators
expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being
sold “As-Is” without any warranty whatsoever including, without limitation, the Limited Warranty as described
herein, notwithstanding anything stated herein to the contrary.
Submitting A Claim: The customer shall return the product to the original purchase point based on its return
policy. In case the return policy period has expired and the product is within warranty, the customer shall
submit a claim to D-Link as outlined below:

The customer must submit with the product as part of the claim a written description of the Hardware
defect or Software nonconformance in sufficient detail to allow D-Link to confirm the same.
71

The original product owner must obtain a Return Material Authorization (“RMA”) number from
the Authorized D-Link Service Office and, if requested, provide written proof of purchase of the
product (such as a copy of the dated purchase invoice for the product) before the warranty service
is provided.

After an RMA number is issued, the defective product must be packaged securely in the original
or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA
number must be prominently marked on the outside of the package. Do not include any manuals or
accessories in the shipping package. D-Link will only replace the defective portion of the Product
and will not ship back any accessories.
The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery
(“COD”) is allowed. Products sent COD will either be rejected by D-Link or become the property of
D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 17595
Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that
are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via
UPS Ground or any common carrier selected by D-Link, with shipping charges prepaid. Expedited
shipping is available if shipping charges are prepaid by the customer and upon request.
D-Link may reject or return any product that is not packaged and shipped in strict compliance with the
foregoing requirements, or for which an RMA number is not visible from the outside of the package. The
product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that
is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link
not to be defective or non-conforming.
What Is Not Covered: This limited warranty provided by D-Link does not cover: Products, if in D-Link’s judgment,
have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty
installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation
for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial
installation, installation and removal of the product for repair, and shipping costs; Operational adjustments
covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment,
due to act of God, failures due to power surge, and cosmetic damage; Any hardware, software, firmware
or other products or services provided by anyone other than D-Link; Products that have been purchased
from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the liquidators
expressly disclaim their warranty obligation pertaining to the product. Repair by anyone other than D-Link
or an Authorized D-Link Service Office will void this Warranty.
Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT
IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING, WITHOUT
LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY
WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO
NINETY (90) DAYS. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED
HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT
IS WITH THE PURCHASER OF THE PRODUCT.

Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY
CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY
LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER
DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES
FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE
OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S
PRODUCT IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR
INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING
FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY
BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS
REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. THE
MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF
THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN WARRANTIES
AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES,
EXPRESS, IMPLIED OR STATUTORY
72
Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Some states do
not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied
warranty lasts, so the foregoing limitations and exclusions may not apply. This limited warranty provides specific
legal rights and the product owner may also have other rights which vary from state to state.
Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered trademarks
are the property of their respective manufacturers or owners.
Copyright Statement: No part of this publication or documentation accompanying this Product may
be reproduced in any form or by any means or used to make any derivative such as translation,
transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as
stipulated by the United States Copyright Act of 1976. Contents are subject to change without prior notice.
Copyright© 2002 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.
CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communication. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:



Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
The Manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications
to this equipment; such modifications could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
The antenna(s) used for this equipment must be installed to provide a separation distance of at least
eight inches (20 cm) from all persons.
This transmitter must not be operated in conjunction with any other antenna.
73
Registration
Product registration is entirely voluntary and failure to complete or
return this form will not diminish your warranty rights.
10/11/04
74
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement