Dimplex GDC12RBA Instruction manual

Dimplex GDC12RBA Instruction manual
VERY IMPORTANT!
Do not install or use your portable air conditioner unit
before carefully reading this instruction manual.
MODEL: GDC9RWA / GDC12RBA / GDC12RWA
GDC12RCWA / GDC12RCBA / GDC14RBA
GDC14RWA / GDC14RCWA / GDC14RCBA
INSTRUCTIONS FOR USE
Please retain this manual for product warranty and
future reference
CAUTION!
1." DO NOT BLOCK VENTILATION "! Please make sure the inlet and outlet
ventilation is not blocked at all times.
2. Operate this unit on a horizontal surface to avoid water leakage.
3. Do not operate this unit in an explosive or corrosive atmosphere.
4. Operate this unit in an ambient temperature of 17~43 degrees Celsius when
switched to cooling and when switched to heating, the ambient operating
temperature should be 5~23 degrees Celsius.
5. Clean the air filter periodically to enjoy the most efficient cooling.
6. When the unit is turned off, please wait at least 3 minutes before restarting it.
This is to prevent the compressor from being damaged.
7. This unit needs to be plugged into a 10 Amp power point.
Please do not use any extension cords with this unit.
8. This unit is for indoor operation only.
9. Make sure the adjustable air vent is open, and also the exhaust pipe and drain pipe if
fitted are extended to the closest window before using.
10. When the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid hazard.
11. The batteries, from the remote control, must be removed from the appliance
before it is scrapped and must be disposed of safely.
12. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
PORTABLE AIR CONDITIONER
person responsible for their safety.
13. Children should be supervised to ensure that they do not play with the appliance.
Important.
The air conditioning unit must always be stored and
transported upright.
In case of doubt we suggest to wait for at least 24
hours before you start the air-conditioning unit.
CONGRATULATIONS ON YOUR SELECTION
OF A QUALITY PORTABLE AIR CONDITIONER
PORTABLE AIR CONDITIONER
Your Air Conditioner has been designed and manufactured to the
highest standards of modern engineering.
One of its many features is a remote control device which allows you
to control all functions conveniently.
- Moves easily from room to room on easy glide castors
- No installation required-just plug into any household 10 Amp
power outlet
- Refrigerated air system designed to cool instantly whenever
you want it
- Heated air system design heats instantly whenever you
want it
- Powerful dehumidification process and filtered air cycle for
improved breathing conditions
- If the remote control function is not required, your one touch
electronic pad provides easy to identify manual operation
- 24 hour programmable timer that can be used with either the air
conditioning or dehumidification setting
- Unique sleep control function
- 220-240 Volt 50Hz operation
- 1.6 meter cord with plug
CONTENTS
1 / Air control unit
2 / 1-remote control unit
3/ Window kit
NAMES OF THE PARTS
PUSH BUTTON SWITCHES & DESCRIPTION OF FUNCTION
1. Push button switch
2. Display screen
3. Adjustable air vent
4. Window kit adaptor
5. Exhaust tube
6. Drain hose ( cooling &heating
model only)
1. POWER KEY
Press to turn unit "ON" or "OFF".
2. FUNCTION
Press this key to select refrigeration, heat or dehumidification.
(Heating function is only available in the following models: GDC12RCWA / GDC12RCBA /
GDC14RCWA / GDC14RCBA)
3. TEMPERATURE REGULATION KEY (UP)
This key raises the preset temperature by 1℃ each time it is pressed to a maximum of 30℃
4. TEMPERATURE REGULATION KEY (DOWN)
7. Cool inlet
8. Cool air filter
9. Hot inlet
This key lowers the preset temperature by 1℃ each time it is pressed to a minimum of 17℃.
※ In normal conditions, the temperature data which appears on the panel is the ambient
temperature, not the temperature which is set by the user. When the user has adjusted
and set the temperature to desired level, the data on the panel will return to the ambient
10. Drain plug
temperature 5 seconds later.
11. Hot air filter
The ambient temperature will descend or change according to the temperature which is
set by the user, but the temperature descendant time and speed will depend on the
environment and space where it operates.
For example, if the ambient temperature is too hot or the room is too large, the rate at
Note: make sure drain plug is fitted before use. ( 10 )
which the temperature descends will be slow, and the cooling efficiency will be poor as
well.
5. L.E.D. DISPLAY
cally after the set time is over.
Indicates the current room temperature or the time setting. If it’s
adjusted by the user the display will return to the pre-set temperature
automatically.
8. SLEEP CONTROL
FUNCTION
When setting the "sleep comfort" mode please ensure that you
then set the number of hours required and press the timer
Error Display
E1: Indicates open circuit or short circuit in room temperature sensor.
button till those hours are indicated on the L.E.D display. After
E2: Indicates open circuit or short circuit in pipe temperature sensor.
setting the hours the L.E.D. display will automatically return to
E7: Indicates the water is full inside.
the current pre-set temperature. To increase this setting press
Please contact an authorized service centre if any of the above error messages are shown.
6. SPEED
the "UP" button and for each press, the temperature will be
Press to select LOW, MEDIUM, HIGH or AUTO fan speed.
increased by 1℃. Likewise to set for a lower temperature, press
If "AUTO" is selected, the unit operates at maximum cooling
capacity when the room temperature less the setting temperature
the “DOWN” button and for each press, the temperature will be
is above 2℃.
decreased by 1℃.
When the room temperature less the set temperature is below
During the course of this cycle, to ensure maximum sleep
2℃, the unit operates at middle cooling capacity.
comfort, the micro-processor memory will raise the pre-set
When the room temperature equal the set temperature, the
temperature 0.5℃ each half hour to a maximum of 2℃ over two
unit operates at minimum capacity.
hours and then maintain that temperature for the balance of the
If "HIGH" is selected, the unit operates at maximum cooling
time set.
capacity regardless of the pre-set temperature. Similar operation is
The portable air conditioner is fitted with a 3 minute compressor
applied when "MEDIUM" OR “LOW" is manually selected.
delay protection circuit which simply means that the compressor
requires 3 minutes to start. From either being switched on, or
7. PROGRAMMABLE Programmable timer ON/OFF key.
TIMER
when changing from “dehumidify” to any air conditioning cycle
TIMER-ON: The timer-on key is used to turn the unit on
chosen.
automatically when the set time is reached.
(The indicator light will be turned on when the timer is
functioning.)
1. Press the "TIMER" key at stand-by status to set the time.
Choose the function desired (refrigeration, heat or
9.”E7”
When the unit warns of full water, please unplug the water
stopper at the back of the unit and then lean the unit to drain the
water out. Then the unit can be restarted. If the error: E7 is
presented again, please find a specialized person to repair.
dehumidification.)
2. Once the set hour has come to an end, the unit will turn on
automatically.
3. If you press the “POWER” key before the timer is complete, the
Note: Heating function does not operate if the ambient temperature is over 23℃.
Cooling function does not operate if the ambient temperature is over 43℃.
(Heating function is only available in the following models: GDC12RCWA / GDC12RCBA /
set time will be cancelled and the unit will remain turned on.
TIMER-OFF: The timer-off is used to turn the unit off automati-
GDC14RCWA / GDC14RCBA)
REMOTE CONTROL FUNCTION
INSTALLATION
Install the portable air conditioner in a flat and spacious location where
the air inlets and outlets will not be blocked. A minimum clearance of
40cm from a wall or other obstacles should be kept (as pictured below ).
The appliance should not be used in the laundry.
NOTICE
1. POWER
ON/OFF switch
2. FUNC
Function “MODE” selector
3. TIMER
Hourly programming
4. AUTO
Automatic fan speed
5. HI
High fan speed
exhaust hose automatically when the unit is in the cooling function.
6. MID
Medium fan speed
Contrarily when the unit is in heating function and the water level reaches
7. LOW
Low fan speed
the detected level, it will begin to pump for sixty seconds. After sixty
8. SLEEP
Night operation selector
seconds in the pump function, if the water level is still on the detected
9. TEMP.
Temperature selector
level, the unit will stop working and present "E7" warning. Then after
For Reverse cycle Cooling / Heating models only. (GDC12RCWA /
GDC12RCBA / GDC14RCWA / GDC14RCBA)
This unit can evaporate the condensation and flow out through the
three seconds of revealing error, the unit will rework automatically.
Please make sure the drain plug is fitted to the drain outlet before use
(10), and the exhaust and drain pipe is extended to the closest window
when the unit is running.
To remove the air filter, please follow the arrow direction and push the
filter lightly. Then take out the filter for cleaning.
MAINTENANCE
PLEASE DISCONNECT THE POWER CORD BEFORE.
AIR FILTER
The air filter located on both sides of the unit can be removed, simply by
pulling the frame in an upward motion.
CONDENSER/EVAPORATOR
Use a brush attachment with a vacuum cleaner.
CABINET
Wipe with a damp cloth and polish with a soft cloth.
POWER SUPPLY
(1) Confirm the correct power.
(2) Insert the plug into the power outlet firmly.
In case of a dangerous water leak, prevent the power cord from
getting wet.
(3) Don’t pull the power cord by force because it will cause damage to
the power cables.
PLACE FOR USE
(1) Because the machine exerts hot air, please don’t operate it in a confined
place.
(2) Don’t place the machine in a sunlit corner otherwise the colours of the
cabinet will fade.
HELPFUL HINTS
This unit is fitted with a special thermal cut off device.
When selecting the refrigerating function, the unit should operate in
room temperatures between 17-43℃, and when selecting the heating
function the room temperature must be between 5-23℃.
Please ensure the unit is not placed against objects which will
obstruct air intake e.g. furniture or curtains as this will affect it's
performance drastically.
Do not place the unit in direct sunlight, as this may cause the unit to
overheat and turn off.
EXHAUST PIPE AND DRAIN PIPE
●
To remove exhaust pipe, press down slightly and pull away from the unit.
●
Picture indicates the removal of the exhaust pipe.
●
Make sure the exhaust pipe and the drain pipe are extended to the
closest window.
TROUBLE SHOOTING
SPECIFICATIONS
Never try to repair or dismantle the air conditioner yourself. Unauthorized repairs may
Model No.
GDC9RWA
GDC12RWA / GDC12RBA
result in the loss of warranty and can endanger the user and the property.
Power Source
220-240V~ 50Hz AC
220-240V~ 50Hz AC
Power Consumption
1080W
1452W
1250W
1480W
2600W
3500W
Problem
The air
Cause
No power supply.
conditioner does
not function.
The air
conditioner does
not seem to
perform.
The alarm light is on.
Solution
Connect to a functioning outlet
(EN14511)
and switch on.
Rated Power
Empty the internal water
(EN60335)
container.
Cooling Capacity
Timer function is active.
Deactivate TIMER function.
In direct sunlight.
Close curtains.
Windows or doors open,
Close doors and windows, place
many people or a heat
an extra air conditioner.
source in the room.
Dirty filter
Clean the filter(s).
Air inlet or air outlet blocked.
Remove the blockage.
Room temperature lower
Change temperature selection.
than the selected value.
3
Air Flow
400 M /H
420 M3/H
Moisture Removed
32 L/DAY
50 L/DAY
Refrigerant
R410A
R410A
2
Min. room size
10m
10m2
Dimensions (mm)
476W x 358D x 840H
476W x 358D x 840H
Net Weight
28.5KG
29.5KG
Model No.
GDC12RCWA / GDC12RCBA
GDC14RWA / GDC14RBA
Power Source
220-240V~ 50Hz AC
220-240V~ 50Hz AC
1452W / 1452W
1660W
Power Consumption
The unit is noisy.
Unit is not level.
Place on an even, solid surface
(less vibrations.)
Cooling / Heating
(EN14511)
The compressor
The overheat protection is
Wait 30 minutes until the
does not work.
probably activated.
temperature has decreased, then
Rated Power
turn the unit on again.
(EN60335)
1480W
1700W
Cooling Capacity
3500W
4000W
Heating Capacity
3500W
N/A
Air Flow
3
420 M /H
450 M3/H
Moisture Removed
50 L/DAY
60 L/DAY
To correct problems not mentioned in the table and/or if the recommended solutions fail
Refrigerant
R410A
R410A
to solve the problem, please contact an authorized service centre.
Min. room size
10m
10m2
Dimensions (mm)
476W x 358D x 840H
476W x 358D x 840H
Net Weight
30.5KG
31.5KG
The remote
control does not
function.
Distance too long.
Remote control signal not
detected by the control
Make sure the remote control is
correctly aimed at the control
panel.
panel.
The batteries are drained
Replace the batteries.
Please contact Glen Dimplex for your nearest authorized service agent:
Australia – 1300 556 816 New Zealand – (09) 274 8265
2
Model No.
GDC14RCWA / GDC14RCBA
Power Source
220-240V~ 50Hz AC
Power Consumption
1660W/1660W
(EN14511)
Rated Power
(EN60335)
1700W
Cooling Capacity
4000W
Heating Capacity
4000W
Air Flow
450 M3/H
Moisture Removed
60 L/DAY
Refrigerant
R410A
Min. room size
10m
Dimensions (mm)
476W x 358D x 840H
Net Weight
32.5KG
2
If you have any issues with your unit, please contact Glen Dimplex for
your nearest service agent. Proof of purchase is required at the time of
service.
Glen Dimplex Australasia Ltd
Glen Dimplex Australia Pty Ltd
38 Harris Road, East Tamaki,
2/205 Abbotts Road,
Manukau, Auckland 2013
Dandenong South VIC 3175
New Zealand
Australia
Ph: (09) 274 8265
Ph: 1300 556 816
Fx: 0800 112 020
Fx: 1800 058 900
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement