CHANNEL VISION
Limited Warranty
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase.
This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment. This warranty is extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original purchase date will be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling (800) 840-
0288 toll free. A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights
(which vary from state to state). If a problem with this product develops during or after the warranty period, please contact Channel Vision Technology, your dealer or any factory-authorized service center.
500-153 rev B
How IR repeating works
Expansion
Pwr al Zo
Glob ne
IR
Receiver
Model
P-1205
C
HANNEL
V ISION
TM
The IR receiver is wired to the IR hub which routes the signal to IR emitters
Glo bal
IR
Rec eive r
Emitters e
Zon
+12
250
DC mA
3
2
1
5
4
7
Pow er
8
6
0
9
Point an
IR remote control at the IR receiver
And the emitter CD player repeats the IR signal in the other room.
Be sure the emitter is attached directly over the component’s IR receiver.
To locate the IR receiver, shine a flashlight into the unit and look for the sensor.
Specifications: (typical)
Voltage Requirements:
IR Freq. range supported:
IR pickup range:
IR receiver head dimensions:
Color:
8 - 12 VDC
30 kHz - 60 kHz
40 ft. @ 38kHz, 25 ft. @ 56kHz
0.65” x 0.35” x 0.25”
Black
Specifications subject to change without notice.
End view ribbon cable
IR receiver wire pinout
+V
(white dash or brown wire)
Typical IR receiver connections (ref only)
Sig
Gnd
+V
Tip
Collar
Ring
0.35”
1 - hole mount
0.65”
IR receiver head
The IR-2400 includes these items:
36”
Features:
!
Plasma Proof IR receiver
!
Status LEDs for IR signal indication
!
Versatile mounting accessaries: Install as
Very small receiver
In-cabinet tube type receiver
Unobtrusive desktop type receiver
1 - tabletop mount
+V = brown wire
1 - IR receiver holster
Sig.
Gnd.
+V
Using the IR-2400 with the P-1205 Mounting the IR receiver: Option 1 - Using the holster
Mount the IR receiver to the TV or on a surface within line of sight of your remote control.
Note: Match the Signal,
Ground, and +Voltage terminals on the IR-2400 with the corresponding terminals on the P-1205
Expansion
IR
Receiver
Pwr
Global Zone
Model
P-1205
C HANNEL
V ISION
IR
Receiver
Emitters
Global
+12DC
Zone
Sat radio
DVD player
CD player
Receiver
The IR-2400 can be directly connected to the P-1205 in two different ways:
1) Through the 3.5mm jack
2) Through the screw terminal connector
For larger systems, a parallel connecting block such as the C-1201(not shown) can be used to connect several IR receivers to the IR input of the P-1205.
Mounting the IR receiver: Option 2 - Using the hole mount
Drill a 3/4” hole .
Push the IR receiver head through the hole.
Insert the IR receiver head into the IR receiver hole mount.
Remove the backing from the tape and attach the
IR receiver holster in the desired location.
Snap IR receiver head into the holster as shown.
Mounting the IR receiver: Option 3 - Using the tabletop mount
Push the IR receiver head through the hole in the tabletop mount.
Insert the IR receiver head into the IR receiver hole mount.
Push the IR receiver hole mount and IR receiver head back into the hole in the tabletop mount.
To secure the mount, remove the backing from the foam tape on the bottom of the unit and attach the mount to any flat surface.
Push the IR receiver hole mount and IR receiver head back into the hole.
