Yamaha | YID-W10 | Owner`s manual | Yamaha YID-W10 Owner`s manual

Yamaha YID-W10 Owner`s manual
UC
English
YID-W10
Wireless System for iPod
Système sans fil pour iPod
OWNER’S MANUAL
MODE D’EMPLOI
Français
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may
void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3. NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., USA 6660 Orangethorpe Ave., Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules.
Operation is subject to the following two conditions:
1) this device may not cause interference, and
2) this device must accept any interference, including interference that may cause undesired operation of this device.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This equipment compiles with FCC/IC radiation
exposure limits set forth for uncontrolled equipment
and meets the FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65 and RSS-102
of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that it
deemed to comply without maximum permissive
exposure evaluation (MPE). But it is desirable that it
should be installed and operated with at least 20 cm
and more between the radiator and person’s body
(excluding extremities: hands, wrists, feet and ankles).
FCC WARNING
Change or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
1 En
Caution: Read this before operating this unit.
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
3 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this
unit in an environment with high humidity (i.e. a
room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal
injury.
4 Avoid installing this unit where foreign object
may fall onto this unit and/or this unit may be
exposed to liquid dripping or splashing. On the
top of this unit, do not place:
– Other components, as they may cause damage and/
or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
5 Do not cover this unit with a newspaper,
tablecloth, curtain, etc. in order not to obstruct
heat radiation. If the temperature inside this unit
rises, it may cause fire, damage to this unit, and/or
personal injury.
6 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
7 Do not use force on switches, knobs and/or cords.
8 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
9 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
10 Be sure to read the “Troubleshooting” section on
common operating errors before concluding that
this unit is faulty.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
Radio waves may affect electro-medical devices.
Do not use this unit near medical devices or inside
medical facilities.
Do not use this unit within 22 cm (9 in) of persons with
a heart pacemaker implant or defibrillator implant.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
This unit may affect radio waves of iPhone when
iPhone is charged by using this unit. In addition, radio
waves of this unit and iPhone may interfere with each
other. If you have a problem with your telephone call,
disconnect your iPhone from this unit.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most
out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear
without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic
Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from
excessive volume levels.
2 En
Introduction
1: Connection
YID-W10 is a wireless system designed for iPod/
iPhone series. YID-W10 employs the Yamaha
“yAired” technology to establish a wireless
connection with another Yamaha dock-compatible
component (hereinafter referred to as “Yamaha
component”) that supports “yAired” and enables
playback of the iPod/iPhone audio on your Yamaha
component. For video, enjoy it on your iPod/iPhone
display.
Also the receiver (YIR-W10) can be used for
charging the iPod/iPhone, or to play music for an
extended time.
Operation and function depend on your iPod/iPhone
model and Yamaha component. Refer to the owner’s
manuals supplied with your iPod/iPhone and
Yamaha component.
This unit is compatible with iPod (5th generation),
iPod classic, iPod nano, iPod touch, iPhone, iPhone
3G, iPhone 3GS (as of April 2010).
• Designed to dock iPod/iPhone with YID-W10
compatible Yamaha products.
• Please find the compatible Yamaha products
through our website.
http://www.yamaha.com/
1 Turn off your Yamaha component and
then disconnect its power cable from the
AC outlet.
2 Connect the dock cable to the Yamaha
component.
DOCK
DOCK
Dock cable
12
A
3
B
Note
Be sure to connect the dock cable firmly. If the
connection is loose, some noise may be output.
3 Connect the power cable to the AC outlet
and then turn on your Yamaha
component.
2: Group ID setting
Yamaha yAired
Real-time uncompressed music transfer without
sound degradation is realized by Yamaha original
digital wireless transfer technology, yAired. You can
also control system on/off and volume with the iPod/
iPhone by yAired.
Match the group IDs of the transmitter and
the receiver.
The default setting is A2.
A
B
Included items
1
2
3
Check that you have received all of the following
items.
Transmitter (YIT-W11TX)
12
A
Receiver (YIR-W10)
12
A
3
B
A B
1 2 3
3
B
3 En
3: Playback
1 Connect your iPod/iPhone to the
transmitter.
The green LED on the transmitter (YIT-W11TX)
and blue LED on the receiver (YIR-W10) light up
if a wireless connection between the transmitter
and receiver is established.
2 Start playback on your iPod/iPhone.
Operation and function depend on your iPod/
iPhone model and Yamaha component. Refer to
the owner’s manuals supplied with your iPod/
iPhone and Yamaha component.
Notes
• In case noises are output from the speaker, place
the receiver away from your Yamaha component.
• The transmitter is powered by the battery of your
iPod/iPhone. When your battery of iPod/iPhone
becomes empty, charge your iPod/iPhone.
Status LED
y
• The transmitter stops wireless communication
automatically after a short time you stop iPod/
iPhone playback.
• To disconnect the iPod/iPhone from the
transmitter, pull it upward.
Status LED
Transmitter LED status
LED
Status
Lights up green
Wireless communication between the transmitter and receiver is
established.
Flashes green once
Adjusting the volume level.
Flashes green continuously
Connection in progress, please wait.
Flashes red once
The volume of Yamaha component is set to maximum or
minimum.
Flashes red for 2 seconds
An unsupported iPod is connected.
Flashes red continuously
Error occurs. Remove the iPod/iPhone from the transmitter, and
connect again.
Flashes red 2 times continuously The battery of the iPod/iPhone is low.
Off
An iPod/iPhone is not connected or wireless communication has
not been established.
Receiver LED status
LED
Status
Lights up blue
Wireless communication between the transmitter and receiver is
established.
Flashes blue once
Adjusting the volume level.
Flashes blue
Connection in progress, please wait.
Flashes blue rapidly
Error occurs. The receiver is in need of repair.
Off
An iPod/iPhone is not connected or wireless communication has
not been established.
4 En
4: Battery charge
To charge your iPod/iPhone, connect it to the transmitter, and then station the transmitter with
your iPod/iPhone onto the receiver.
Note
Do not push the transmitter detection switch hard.
Transmitter detection switch
12
A
12
A
3
B
3
B
Troubleshooting
If the unit does not function properly, first of all, check the firmware of your iPod/iPhone is the latest version.
If it is the latest version, refer to the table below. If the problem you are experiencing is not listed below, or if
the instruction below does not help, contact the nearest authorized Yamaha dealer or service center.
Transmitter
LED
Green: Off
Problem
No sound.
Cause
Playback your iPod/iPhone,
or run the YouTube or other
applications.
Your iPod/iPhone is not
connected to the transmitter
firmly.
Reconnect your iPod/iPhone
to the transmitter firmly.
The battery of your iPod/
iPhone is empty.
Charge your iPod/iPhone.
The dock cable is not
connected to your Yamaha
component.
Connect the dock cable to
your Yamaha component.
The group IDs of the
transmitter and receiver are
set to the different value.
Match the group IDs.
The power is not supplied to
the receiver from your
Yamaha component.
Change the setting of your
Yamaha component
referring to its owner’s
manual.
Red: Off
Green: flashes
Red: Off
No sound.
Remedy
No sound is output from
your iPod/iPhone.
5 En
Transmitter
LED
Green: flashes
Problem
Cause
Remedy
There is a device
(microwave oven, cordless
phone, Wi-Fi, etc.)
outputting signals in 2.4
GHz frequency band nearby.
Move YID-W10 away from
the device.
The signal from the
transmitter is blocked by
your body, metallic objects,
or wall, etc.
Change the position of the
transmitter to avoid the
object blocking the signal.
The position of the
transmitter is too far from
the receiver.
Move the transmitter closer
to the receiver.
No sound.
Communication error of
your iPod/iPhone, and the
transmitter.
Reconnect your iPod/iPhone
to the transmitter firmly.
If this status occurs
frequently, disconnect your
iPod/iPhone from the
transmitter, restart it, and
then reconnect firmly.
Controlling
volume on your
iPod does not
work.
Your iPod is recognized as
an unsupported model.
Use an iPod supported by
YID-W10.
If your iPod is the supported
model, reconnect it to the
transmitter firmly.
If this status occurs
frequently, disconnect your
iPod from the transmitter,
restart it, and then reconnect
firmly.
No sound.
Communication error of
your iPod/iPhone, and the
transmitter.
Reconnect your iPod/iPhone
to the transmitter firmly.
If this status occurs
frequently, disconnect your
iPod/iPhone from the
transmitter, restart it, and
then reconnect firmly.
The sound is
interrupted.
Red: Off
Green: flashes
or lights up
Red: flashes
Green: flashes
or lights up
Red: flashes for
a short time
Green: flashes
twice
Red: Off
6 En
Transmitter
LED
Green: lights up
Problem
No sound
Cause
Remedy
The volume is set to the
minimum.
Set the volume properly.
Your Yamaha component is
turned off.
Turn on your Yamaha
component.
The input source of your
Yamaha component is not
set properly.
Set the input source
properly.
Earphones or other device
are connected to your iPod/
iPhone.
Disconnect earphones or
other device.
The volume of
iPod/iPhone
does not change
when you
operate the
volume of your
Yamaha
component.
Wireless communications
are established between this
unit’s transmitter and
multiple “yAired” devices
simultaneously.
Set the group IDs of the
other “yAired” devices to
the different value.
Sound is output
suddenly despite
your iPod/
iPhone is not
connected to the
transmitter.
Wireless communication is
established between the
receiver and another
“yAired” device.
Set the group ID of another
“yAired” device to the
different value.
Ring tone is
output from your
Yamaha
component when
your iPhone
receives an
incoming call.
Ring tone is output from
your Yamaha component
when your iPhone receives
an incoming call.
If you do not want your
Yamaha component to
output ring tone, set your
iPhone to the silent mode.
The battery is
not charged.
The battery charge function
is not activated on your
Yamaha component.
Change the setting of your
Yamaha component
referring to its owner’s
manual.
The Wi-Fi
communication
is unstable when
you are using
YID-W10.
The signal from YID-W10
interferes with Wi-Fi
communication.
Disconnect your iPod/
iPhone from the transmitter,
and then reconnect firmly
after a while.
If this situation occurs
frequently, move YID-W10
away from the Wi-Fi
components.
Red: Off
7 En
Specifications
Supported iPod (as of April 2010)
.... iPod (5th generation), iPod classic, iPod nano,
iPod touch
Supported iPhone (as of April 2010)
...........................iPhone, iPhone 3G, iPhone 3GS
Frequency ................................................... 2.4 GHz
Transmission Range .................Approx. 20m (66 ft)
(without interference)
Number of units which can be simultaneously
transmitted to (YIT-W11TX)
...Up to 7 units (depending on the circumstances)
Latency ........................................................... 12 ms
Power Consumption (Charging)........................ 4 W
Power Consumption (No charge) ....... Less than 1W
INPUT / OUTPUT ........................................DOCK
Dimensions (W x H x D)
YIT-W11TX ........................45.3 x 94 x 17.6 mm
(1-3/4 x 3-3/4 x 0-3/4 in)
YIR-W10 ...................................91 x 54 x 88 mm
(3-5/8 x 2-1/8 x 3-1/2 in)
Cable Length (YIR-W10)....................1.2 m (3.9 ft)
Weight
YIT-W11TX .....................................42 g (1.5 oz)
YIR-W10 ........................................260 g (9.0 oz)
The rating marking of “5 V
for the charge to iPod/iPhone.
1.0 A” is marking
* Specifications are subject to change without notice.
8 En
The “
” and “yAired” are
trademarks of Yamaha Corporation.
iPhone, iPod, iPod classic, iPod nano and
iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries.
“Made for iPod” and “Made for iPhone”
mean that an electronic accessory has been
designed to connect specifically to iPod or
iPhone, respectively, and has been certified
by the developer to meet Apple performance
standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
© 2010 Yamaha Corporation
Printed in China
WV30490
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising