Chauvet | Colorado 2 Zoom Tour | User manual | Chauvet Colorado 2 Zoom Tour User manual

Chauvet Colorado 2 Zoom Tour User manual
Quick Reference Guide
COLORado™ 2 Zoom Tour QRG
About This
Guide
The COLORado™ 2 Zoom Tour Quick Reference Guide (QRG) contains
the product’s connection and mounting information, as well as the menu
options and the DMX values.
·
Disclaimer
Safety Notes
·
·
·
·
·
·
·
·
·
·
·
·
·
·
What Is
Included
·
·
·
Refer to this product’s User Manual for detailed information and
instructions. You can download the User Manual from the CHAUVET®
website: www.chauvetpro.com.
Read ALL the disclaimers and Safety Notes in this document, as well as
those in the product’s User Manual before installing, operating, or
maintaining this product.
DO NOT open this product unless instructed. It contains no user
serviceable parts.
DO NOT aim this product toward any surface closer than 16 feet (5 m).
You may damage or overheat the illuminated surface.
DO NOT aim this product toward the Sun. The lenses could concentrate
the solar energy and cause internal overheating.
DO NOT look at the light source when this product is on.
DO NOT touch the product when it is operating because it may be very
hot.
DO NOT cover the ventilation slots when the product is operating to
avoid internal overheating.
DO NOT install or operate this product where there is less than 50 cm to
the nearest surface to allow adequate ventilation around it.
DO NOT leave any flammable material within 50 cm from this product
while operating or connected to the power outlet to minimize the risk of
fire.
DO NOT mount this product overhead without using a safety cable.
DO NOT operate this product outdoors or in any location where dust,
excessive heat, water, or humidity may affect it.
DO NOT operate this product if you see damage on the housing, lenses,
or cables. In any of these cases, have the damaged parts replaced by an
authorized technician immediately.
DO NOT connect this product to a dimmer or rheostat.
ONLY connect this product to a grounded and protected circuit.
One COLORado™ 2 Zoom Tour ·
One NEUTRIK® powerCON® ·
to Edison Plug Power Input Cord ·
One Accessory Holder
Page 2 of 12
One Gel Frame
One Warranty Card
One Quick Reference Guide
COLORado™ 2 Zoom Tour QRG
Features
·
·
3, 4, 5, 6, or 12-channel DMX control
Operating modes
3-channel:
RGB
3-channel:
HSV
4-channel:
RGB, dimmer
4-channel:
RGBW
5-channel:
RGBW, dimmer
6-channel:
RGBW, dimmer, strobe
12-channel: RGBW, dimmer, color macro, strobe, auto/custom
programs, auto speed, dimmer speed, zoom, zoom
reset
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
RGBW color mixing with or without DMX control
Zoom control with or without DMX control
Built-in automated programs via master/slave or DMX
Recall custom programs via master/slave or DMX
Five distinct dimming curves
RGBW LEDs
Electronic dimmer
Color macros with speed adjustment included
Electronic power supply
NEUTRIK® powerCON® connectors
3- and 5-pin DMX input and output connectors
Additional power output: max 7 units @ 120 VAC
LED display with password protection
Gel frame holder (4 mm max. thickness)
Double-bracketed yoke doubles as a floor stand
Color calibration
Flicker-free operation for HD video
Page 3 of 12
COLORado™ 2 Zoom Tour QRG
Product
Description
The COLORado™ 2 Zoom Tour is an RGBW LED wash product. A single
module houses the internal power supply, the control panel, the LED
drivers, the LED boards, and motorized moving lenses, as well as the power
and signal connectors. The COLORado™ 2 Zoom Tour features a variable
zoom enabling you to change the beam angle via DMX or control panel.
One mounting bracket doubles as a floor mount or a hanging support
bracket.
Power
Power
In/Out
In/Out
DMX In
Control
Panel
DMX
Out
Rear View
Product Overview
Adjustment Knob
Side View
Page 4 of 12
COLORado™ 2 Zoom Tour QRG
AC Power
This product has an auto-ranging power supply that works with an
input voltage range of 100~240 VAC, 50/60 Hz.
Power Linking You can link up to 7 COLORado™ 2 Zoom Tour products at 120
VAC, 60Hz or 15 products at 230VAC, 50Hz. Never exceed this
number.
DMX
Linking
The COLORado™ 2 Zoom Tour can work with a DMX controller
when linked using a regular DMX serial connection.
If you are not familiar with the DMX standard, download the DMX
Primer from www.chauvetpro.com.
DMX The COLORado™ 2 Zoom Tour uses a regular DMX data connection
Connection for DMX personalities, TOUR, ARC.1, AR1.D, ARC.2, AR2.D,
AR2.S, and HSV.
Download the COLORado™ 2 Zoom Tour User Manual. Refer to the
Setup chapter to learn how to connect this product for DMX operation.
To learn how to configure this product for DMX operation, refer to the
Operation chapter.
Master/Slave The COLORado™ 2 Zoom Tour uses the DMX data connection for
Connection Master/Slave mode.
Download the COLORado™ 2 Zoom Tour User Manual. Refer to the
Setup and Operation chapters to learn how to connect and configure
this product for Master/Slave operation.
Page 5 of 12
COLORado™ 2 Zoom Tour QRG
Mounting
Product
Mounting
Diagram
Before mounting this product, read the Safety Notes at the beginning of this
Guide and in the product’s User Manual. Then, follow the mounting
procedure indicated in the Setup chapter of the User Manual.
Overhead Mounting
Floor Mounting
Page 6 of 12
COLORado™ 2 Zoom Tour QRG
Programming
Control Panel
Description
Password
For details on how to program this product, please refer to the product’s
User Manual.
Button
Function
<MENU> Exits from the current menu or function
Enables the currently displayed menu or sets the currently
<ENTER>
selected value into the selected function
Navigates upwards through the menu list and increases the
<UP>
numeric value when in a function
Navigates downwards through the menu list and decreases
<DOWN>
the numeric value when in a function
After being prompted to enter the password, press:
<UP>, <DOWN>, <UP>, <DOWN>, and <ENTER>.
Start Address To ensure full access to all channels in each DMX mode, the highest
recommended DMX addresses are as follows:
Mode
Address
Mode
Address
Mode
Address
TOUR
ARC.1
AR1.D
501
510
509
ARC.2
AR2.D
AR2.S
509
508
507
HSV
510
Page 7 of 12
COLORado™ 2 Zoom Tour QRG
Menu Options
Main Level
STAT
AUTO
DMX
RUN
Programming Levels
R.
G.
B.
W.
Z.
S.
000~255
00~20
AT.01~10
PR.C1~10
001~512
DMX
SLAV
TOUR
PERS
ARC.1
AR1.D
ARC.2
AR2.D
AR2.S
HSV
Page 8 of 12
Description
Combines Red, Green, Blue, and White to
generate a custom color (0~100%)
Changes the beam angle
Strobe frequency (0~20 Hz)
Choose from 10 automatic programs
Choose from 10 customizable programs
Sets the DMX starting address
Receives signals from DMX controller
Receives signals from Master unit
12-channel: RGBW, D, A/C, AS, DS, Macro,
S, Z, ZR
3 channel: RGB
4-channel: RGB, D
4-channel: RGBW
5-channel: RGBW, D
6-channel: RGBW, D, S
3 channel: HSV
COLORado™ 2 Zoom Tour QRG
Main Level
Programming Levels
UPLD
REST
DIM
DERR
SET
COLR
ZOOM
EDIT
KEY
CAL
Description
Enter password
Enter password
OFF
DIM1~4
BLAC
SAVE
OFF
RGBW
UC
BASE
POS.1
POS.2
R.
G.
B.
W.
PR.
SC.
(C1~10) (01~30)
Z.
S.
T.
F.
ON/OFF
R.
G.
WH
WT
1~11
B.
PASS
W.
(Enter
CAL
R.
pass
RGB RGB
G.
word)
W .W
B.
POS.1
ZOOM
POS.2
000~255
00~20
Transfers custom programs
Defaults fixture
No dimmer
Dimmer curve
All LED’s turn off when DMX signal is lost
All LED’s stay on the last command used
when the DMX signal is lost.
RGB set to “255” = max. output
RGB set to “255” = balanced white
Universal color balance
Sets default zoom position (full movement)
Sets position 1 setting for zoom limit
Sets position 2 setting for zoom limit
Combines Red, Green, Blue, White, and
Zoom, as well as strobe and timers to
create the scenes of a custom program
000~255
Turns the password on or off
000~255
Modifies the color macros used in channel 6
of the TOUR personality
000~255
Defines the color temperature used when
COLOR is set to RGB to W
000~255 Sets min/max position of zoom
Page 9 of 12
COLORado™ 2 Zoom Tour QRG
DMX Values
Tour
Channel Function
1
2
3
4
5
6
7
8
Value
Percent/Setting
000 ó 255 0~100%
0~100%
000 ó 255
When CUS. 01-10 in CH. 8 is activated
0~100%
000 ó 255
When CUS. 01-10 in CH. 8 is activated
000 ó 255 0~100%
000 ó 255 0~100%
000 ó 010 No Function
011 ó 030 R: 100% G: 0~100% B: 0%
031 ó 050 R: 100~0% G: 100%
B: 0%
051 ó 070 R: 0%
G: 100%
B: 0~100%
071 ó 090 R: 0%
G: 100~0% B: 100%
091 ó 110 R: 0~100% G: 0%
B: 100%
111 ó 130 R: 100% G: 0%
B: 100~0%
131 ó 150 R: 100% G: 0~100% B: 0~100%
151 ó 170 R: 100~0% G: 100~0% B: 100%
B: 100% W: 100%
Color Macro 171 ó 200 R: 100% G: 100%
201 ó 205 White 1:
+ White
3,200 K
206 ó 210 White 2:
3,400 K
Balance
211 ó 215 White 3:
4,200 K
216 ó 220 White 4:
4,900 K
221 ó 225 White 5:
5,600 K
226 ó 230 White 6:
5,900 K
231 ó 235 White 7:
6,500 K
236 ó 240 White 8:
7,200 K
241 ó 245 White 9:
8,000 K
246 ó 250 White 10: 8,500 K
250 ó 255 White 10: 10,000 K
000 ó 009 No Function
Strobe
010 ó 255 0~20 Hz
000 ó 040 No function
041 ó 049 Auto 1
050 ó 059 Auto 2
060 ó 069 Auto 3
070 ó 079 Auto 4
080 ó 089 Auto 5
090 ó 099 Auto 6
100 ó 109 Auto 7
Auto +
110 ó 119 Auto 8
Custom
120 ó 129 Auto 9
Programs
130 ó 139 Auto 10
140 ó 149 Custom 1
150 ó 159 Custom 2
160 ó 169 Custom 3
170 ó 179 Custom 4
180 ó 189 Custom 5
190 ó 199 Custom 6
200 ó 209 Custom 7
Continues on the next page
Dimmer
Red
Step Time
Green
Step Time
Blue
White
Page 10 of 12
COLORado™ 2 Zoom Tour QRG
Tour
(Cont.)
Channel Function
AR1.D
ARC.2
AR2.D
Percent/Setting
Auto + Custom
Programs
210 ó 219 Custom 8
220 ó 229 Custom 9
230 ó 255 Custom 10
Auto Speed
000 ó 255 Only when CH. 8 is 041~139
10
Dimmer Speed
000 ó 009
010 ó 029
030 ó 069
070 ó 129
130 ó 189
190 ó 255
11
Zoom
000 ó 255 0~100%
12
Zoom Reset
000 ó 200 No function
201 ó 220 Zoom reset
221 ó 255 No function
8
(Cont.)
9
ARC.1
Value
Channel
Function
Dimmer speed as per Control Panel
Linear dimmer
Non-linear dimmer 1 (fastest)
Non-linear dimmer 2
Non-linear dimmer 3
Non-linear dimmer 4 (slowest)
Value
1
Red
000 ó 255 0~100%
2
Green
000 ó 255 0~100%
3
Blue
000 ó 255 0~100%
Channel
Function
Value
1
Master Dimmer
000 ó 255 0~100%
2
Red
000 ó 255 0~100%
3
Green
000 ó 255 0~100%
4
Blue
000 ó 255 0~100%
Channel
Function
Value
1
Red
000 ó 255 0~100%
2
Green
000 ó 255 0~100%
3
Blue
000 ó 255 0~100%
4
White
000 ó 255 0~100%
Channel
Function
Value
1
Master Dimmer
000 ó 255 0~100%
2
Red
000 ó 255 0~100%
3
Green
000 ó 255 0~100%
4
Blue
000 ó 255 0~100%
5
White
000 ó 255 0~100%
Page 11 of 12
Percent/Setting
Percent/Setting
Percent/Setting
Percent/Setting
COLORado™ 2 Zoom Tour QRG
AR2.S
HSV
Channel
Function
Percent/Setting
Master Dimmer
000 ó 255 0~100%
2
Red
000 ó 255 0~100%
3
Green
000 ó 255 0~100%
4
Blue
000 ó 255 0~100%
5
White
000 ó 255 0~100%
6
Strobe
000 ó 009 No Function
010 ó 255 0~20 Hz
Channel
Contact Us
Value
1
Function
Value
Percent/Setting
1
Hue
000 ó 255 0~100%
2
Saturation
000 ó 255 0~100%
3
Value
000 ó 255 0~100%
World Headquarters
United Kingdom and Ireland
CHAUVET®
CHAUVET® Europe Ltd.
General Information
Address:
Voice:
Fax:
Toll free:
5200 NW 108th Avenue
Sunrise, FL 33351
(954) 929-1115
(954) 929-5560
(800) 762-1084
Technical Support
Voice:
Fax:
Email:
(954) 929-1115 (Press 4)
(954) 756-8015
tech@chauvetlighting.com
World Wide Web
www.chauvetpro.com
General Information
Address:
Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice:
+44 (0)1773 511115
Fax:
+44 (0)1773 511110
Technical Support
Email:
uktech@chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk
Outside the U.S., United Kingdom, or Ireland, contact your distributor of
record. Follow their instructions to request support or to return a product.
Visit our website for contact details.
COLORado™ 2 Zoom Tour QRG – Rev. 11
© Copyright 2012 CHAUVET®
All rights reserved.
Printed in the P. R. C.
Page 12 of 12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising