1M23N19204
USB INTERFACE
Instruction Manual
Thank you for purchasing a CIU-2.
The CIU-2 is a USB interface for communications between Link supported devices and a Windows
computer.
Notes
• Please read this manual thoroughly before using your CIU-2.
• Store this manual in a safe place where it can be accessed at any time.
*A 500mm extension
cord is supplied with
the CIU-2.
• Reproduction of all, or part, of the contents of this manual without prior written permission is
prohibited.
• The contents of this manual are subject to change without prior notice.
• The contents of this manual should be complete, but if you find any errors or unclear points, please
contact us.
• Futaba will not be responsible for the results of use of devices by the customer.
*Windows is registered trademark of Microsoft Corporation.
Specifications
(Specifications and ratings are subject to change without prior notice accompanying technological developments.)
• Interface
: USB Rev1.1 compliant
• USB connector
: USB Series A connector
• Operating voltage : 5.0V ±0.2V (USB bus power)
• Current drain
(At connection, idle): 12.3 ±2.0mA
*The PC must have a USB port (Type A).
• Operating environment:
Temperature -10 ~ 50degrees Celsius
• Dimensions
: 18.2 X 56.5 X 9.0 mm
• Weight
: 7.5g
• Applicable OS
: Windows Vista/XP/2000
Drivers and Link programs must be installed.
• To use the CIU-2, drivers must be installed.
• For communication and setting, Link programs corresponding to each device must be installed.
Install the drivers and Link programs available on the dealer’s website.
Connecting and disconnecting the PC and CIU-2
Connection
1.Turn on the PC power.
2.Connect the CIU-2 to the USB port of the PC.
3.When the CIU-2 is first connected to the PC;
the “Found New Hardware Wizard” shown at
the right is displayed. Install the drivers
downloaded from the dealer’ s website.
USB port
Disconnection
The CIU-2 can be disconnected even while the
PC power is on. However, do not disconnect
the CIU-2 while it is communicating with a Link
supported device.
Example of connection to Link supported device
(The figure below is an example of connection to an MC850C.)
Connection method
1.Connect the CIU-2 to the USB port
of the PC.
Connect the batteries to
2.Connect the Link supported device
the Link supported device
to the CIU-2.
3.Connect the batteries by referring
to the Link supported device
instruction manual.
4.Set the power switch of the Link
supported device to ON.
Power switch
5.Communication with the Link
program is possible.
Connect to PC USB port
When connecting, use the accessory 500m
extension cord, as required.
Connects the connector of
the Link supported device.
Usage Precautions
Do not disassemble the CIU-2. Do not open the CIU-2 case.
Opening the case may damage the PC board. In this case, PC assembly replacement or repair will become
impossible. There is also the danger of fire and electric shock.
Do not expose the CIU-2 to water or other liquids. Do not touch the CIU-2 when you hands are
wet.
Water droplets entering the CIU-2 may cause trouble. There is also the danger of fire and electric shock.
Do not drop or expose the CIU-2 to strong shock.
It may cause trouble.
Do not set anything on top of the CIU-2.
It may cause trouble.
Do not touch the connectors with your hands. Also, do not connect a dusty or dirty connector.
It may cause trouble.
Handle the PC and peripheral devices in accordance with the instruction manual and cautions
and warnings given in the instruction manual of each product.
Special Markings
Pay special attention to the
safety at the parts of this
manual that are indicated by
the following marks.
Symbol:
:Prohibited
Mark
Meaning
Procedures which may lead to a dangerous condition or cause death or serious
injury to the user if not carried out properly, or procedures where the probability of
superficial injury or physical damage is high.
Procedures where the possibility of serious injury to the user is small, but there is a
danger of injury, or physical damage, if not carried out properly.
:Mandatory
<When requesting repair>
Before requesting repair, read this instruction manual again. When there is an abnormality, request repair to your local
Futaba dealer.
FUTABA CORPORATION
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan
©FUTABA CORPORATION
2011,07
(2)
">