GE GFDN110GDWW 7.0 Cu. Ft. capacity Dura Drum gas dryer Quick Specs


Add to my manuals
4 Pages

advertisement

GE GFDN110GDWW 7.0 Cu. Ft. capacity Dura Drum gas dryer Quick Specs | Manualzz

GFDN110GD

GE ® 7.0 Cu. Ft. Super Capacity Frontload Gas Dryer

Dimensions and Installation Information (in inches)

Gas Dryer Rating

120V 60Hz, 6A

Exhaust Options: 3-way via rear, left, and bottom.

Circuit Requirements: An individual, properly grounded branch circuit, protected by a 15-20 amp circuit breaker or a time-delay fuse, is required.

Note: Dryer wall outlet must be located within 36” of service cord entry and accessible when dryer is mounted in position.

Installation Information: For complete information, see installation instructions packed with your dryer.

27 32-3/16

39-3/8

4-1/2

Above illustration intended for dimensional reference only.

Refer to photography for actual product appearance.

4-3/8

For answers to your Monogram, ® GE Profile ™ or

GE ® appliance questions, visit our website at geappliances.com or call GE Answer Center ® service, 800.626.2000.

2-1/2

3-1/2

12

1-3/4

Gas Pipe

Connection

Electrical

Connection

Specification Revised 4/15

GFDN110GD

GE ® 7.0 Cu. Ft. Super Capacity Frontload Gas Dryer

Special Installation Requirements:

Stacked Installation:

• Brackets for stacking dryer over washer are not included with the dryer.

GEFLSTACK or part no. WE25X10018.

Alcove or Closet Installation:

• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.

• The dryer MUST be exhausted to the outside.

• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 0" either side, 3" front and rear

• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".

• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.

• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

Bathroom or Bedroom Installation:

• The dryer MUST be exhausted to the outdoors.

• The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code,

ANSI Z223 for gas dryers.

Minimum Clearance other than Alcove or Closet Installations:

• Minimum clearances to combustible surfaces 0" both sides, 3" rear.

For more information on venting kits and accessories, please call 1-800-GE-CARES.

For answers to your Monogram, ® GE Profile ™ or

GE ® appliance questions, visit our website at geappliances.com or call GE Answer Center ® service, 800.626.2000.

24

Stacked Dimensions (in inches)

3-1/4

49-5/8

Pedestal Dimensions (in inches)

SBSD137HWW - white

This optional 13" pedestal raises the door opening and height of the washer or dryer. Feet on 13" pedestal allow it to adjust to

13-3/8" height.

13

1/2

27

Above illustrations intended for dimensional reference only.

Refer to photography for actual product appearance.

79-5/8

28-3/4

Specification Revised 4/15

GE Dryer Vent

GE Dryer Vent

GFDN110GD

GE ® 7.0 Cu. Ft. Super Capacity Frontload Gas Dryer

Dryer Exhausting Information – Metal Duct Only

For complete information, see installation instructions packed with your dryer.

Ducting Materials: For best performance, this dryer should be vented with 4” diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct.

A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting.

Exhaust Length Calculation:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the

side or bottom of dryer, add one turn.

2. The maximum length of 4’ rigid (aluminum or galvanized) duct which can be tolerated is

shown in the table.

A turn of 45° or less may be ignored. Two 45° turns within the duct length should be

treated as a 90° elbow.

A turn over 45° should be treated as a 90° elbow.

Dryers must be exhausted to the outside.

Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed Down.

For more information on venting kits and accessories, please call 1-800-GE-CARES.

For every extra 90° elbow, reduce the allowable vent system length by 10 ft.

Two 45° elbows will be treated like one 90° elbow.

For the side exhaust installations, add one 90° elbow to the chart.

The total vent system length includes all the straight portions and elbows of the system (transition duct included).

Dryer exhausting information—use metal duct only vertical and horizontal ducting

A

4

A

A

B

Domestic dryer models

2-1/2

GE Frontload Long Vent 7.0 cu. ft. capacity electric dryer

(GFDL)

Long Vent 6.0 - 8.0 cu. ft. capacity electric & gas dryers

(GTDL and GTV)

Long Vent 7.0 cu. ft. capacity electric & gas (GTD42, GTD45,

GTD65, GTX42 and GTX60)

All 3.6 cu. ft. (DSKS, DSKP) electric dryers

4

2-1/2

B

All 6.0 - 8.3 cu. ft. capacity models electric and gas dryers

(GFDS, GFDR, GFDN, GTDS,

GTDN, GHDN, GHDS, GTDP,

GLDP, GTD, HTDP, HTDX)

DCVH480

Laundry Center GUD27

Laundry Center GUD24

35 ft.

46 ft.

37 ft.

30 ft.

23 ft.

56 ft.

45 ft.

35 ft.

25 ft.

90 ft.

60 ft.

45 ft.

48 ft.

40 ft.

32 ft.

43 ft.

33 ft.

24 ft.

135 ft.

125 ft.

115 ft.

105 ft.

95 ft.

120 ft.

100 ft.

85 ft.

70 ft.

60 ft.

55 ft.

90 ft.

60 ft.

Best performance

Maximum length of 4" dia rigid

metal duct

Exhaust hood type

A

4" opening

200 ft.

B

2-1/2" opening

175 ft.

185 ft.

165 ft.

175 ft.

155 ft.

165 ft.

145 ft.

155 ft.

135 ft.

145 ft.

125 ft.

150 ft.

125 ft.

115 ft.

105 ft.

95 ft.

85 ft.

75 ft.

90 ft.

75 ft.

65 ft.

55 ft.

45 ft.

35 ft.

60 ft.

45 ft.

25 ft.

37 ft.

30 ft.

22 ft.

15 ft.

42 ft.

35 ft.

25 ft.

15 ft.

60 ft.

45 ft.

35 ft.

34 ft.

26 ft.

18 ft.

36 ft.

26 ft.

16 ft.

2

3

4

0

1

4

5

1

2

3

4

5

0

1

2

3

4

5

0

Number of 90° turns

0

1

2

3

3

0

1

2

1

2

2

3

0

3

0

1

0

1

2

Specification Revised 4/15

GFDN110GD

GE ® 7.0 Cu. Ft. Super Capacity Frontload Gas Dryer

Features and Benefits

• DuraDrum provides long-lasting dependability

• HE Sensor Dry - Keep your clothes looking and feeling their best. Dual thermistors continually monitor temperature with a sensor bar that measures moisture to prevent over-drying

• Speed Dry quickly dries items and small loads for families on the go

• eDry option—energy saving option reduces dry temperatures on select cycles without sacrificing performance

• 4 heat settings provide the right temperature for the right drying needs

• 6 dry cycles—additional cycles for your clothes-drying needs

• Model GFDN110GDWW – White

GFDN110ED_GDWW

Specification Revised 4/15

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement