AXIS 5570e, 5670e Print Server User’s Manual

AXIS 5570e/AXIS 5670e User’s Manual
AXIS 5570e
AXIS 5670e
User’s Manual
1
2
AXIS 5570e/AXIS 5670e User’s Manual
Safety notices
Take some time to read through the safety notices before installing the AXIS
5570e/AXIS 5670e. Please observe all safety markings and instructions when using this
product.
Warning! - must be observed to avoid bodily injuries.
Caution! - must be observed to avoid loss of data or damage to your equipment.
Important: - must be observed to avoid operational impairment.
Do not proceed any of the above notices, until you have fully understood the
implications.
Electromagnetic Compatibility (EMC) USA - This equipment generates and radiates
radio frequency energy and if not installed and used in accordance with the instruction
manual, may cause interference to radio communications. It has been tested and found
to comply with the limits for a Class A computing device pursuant to Subpart B of Part
15 of FCC rules, which are designed to provide reasonable protection against such
interference when operated in a commercial environment. Operation of this equipment in
a residential area is likely to cause interference in which case the user at his own expense
will be required to take whatever measures may be required to correct the interference.
Shielded cables should be used with this model to ensure compliance with the Class A
limits.
Europe - This digital equipment fulfils the requirements for radiated emission according
to limit B of EN55022/1998 and the requirements for immunity according to
EN55024/1998 information technology equipment (Compliance is not valid for
unshielded network and printer cables).
Liability - Every care has been taken in the preparation of this manual; if you detect
any inaccuracies or omissions, please inform your local Axis office. Axis
Communications AB cannot be held responsible for any technical or typographical errors
and reserves the right to make changes to the product and manuals without prior notice.
Axis Communications AB makes no warranty of any kind with regard to the material
contained within this document, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Axis Communications AB shall not
be liable nor responsible for incidental or consequential damages in connection with the
furnishing, performance or use of this material.
Axis’ Trademarks - AXIS ThinWizard, AXIS IPJumpStarter, AXIS PrintMonitor,
axinstall
Other Trademark Acknowledgments - Adobe Acrobat Reader, Apple, Ethernet,
EtherTalk, IBM, LAN Manager, LAN Server, Macintosh, Microsoft, Novell NetWare, OS/2,
OS/400, AS/400, TokenTalk, UNIX, Windows, are registered trademarks of the respective
holders.
Support Services - Should you require technical assistance, please contact your Axis
3
AXIS 5570e/AXIS 5670e User’s Manual
dealer. If your questions cannot be answered immediately, your Axis dealer will forward
your queries through the appropriate channels to ensure you a rapid response.
On www.axis.com, you will find on-line manuals, technical support, software updates,
application software and corporate information.
AXIS 5570e/AXIS 5670e User’s Manual
Part no.20897
Copyright © Axis Communications AB,2003
Revision 1.0
September 2003
This manual applies to AXIS 5570e/AXIS 5670e with firmware
version 6.42 and higher.
4
AXIS 5570e/AXIS 5670e User’s Manual
Preface
Thank you for purchasing the AXIS 5570e/AXIS 5670e Print Server.
These products have been developed to connect your printers
anywhere in your network, allowing all network users access to the
shared printer resources.
About this manual
This manual provides introductory information as well as detailed
instructions on how to set up and manage the AXIS 5570e/AXIS
5670e in various network environments. It is intended for everyone
involved in installing and managing the AXIS 5570e/AXIS 5670e. To
fully benefit from the manual, you should be familiar with basic
networking principles.
This manual is applicable for the AXIS 5570e/AXIS 5670e, with
firmware release 6.42 and higher.
About Axis
Axis Communications is dedicated to providing innovative solutions
for network-connected computer peripherals. Since the start in 1984,
it has been one of the fastest growing companies in the market and is
now a leader in its field.
Support Services
Should you require any technical assistance, please contact your Axis
dealer. If your questions cannot be answered immediately, your Axis
dealer will forward your queries through the appropriate channels to
ensure you a rapid response.
If you are connected to the Internet, you can find on-line manuals,
technical support, firmware updates, application software, company
information, on the addresses listed below.
http://www.axis.com/techsup
AXIS 5570e/AXIS 5670e User’s Manual
Table of Contents
Table of Contents
Table of Contents 5
Section 1
Introduction 9
Product Model Summary 9
Where to use it 10
How to use it 11
AXIS 5570e/AXIS 5670e Features and Benefits
12
Section 2
Product Overview 14
Hardware Inventory 14
Protocols and Datastreams 15
The AXIS 5570e Network Print Server 16
The AXIS 5670e Network Print Server 16
Section 3
Basic Installation 19
Getting Started 19
Connecting a printer to the Ethernet Network 20
Installation Guide 22
Setting the IP address 24
Section 4
Setting Up - AS/400 (iSeries) 35
SNA Printing - 5494 Mode 36
TN5250E printing (SCS over IP) 48
PPR/PPD Printing - IPDS data streams 51
Section 5
Setting Up - IBM Mainframe (zSeries) 59
SNA Printing 60
TCP/IP TN3270E Printing 70
PPR/PPD Printing - IPDS data streams 82
Section 6
Setting Up - Windows 101
Adding Printers in Windows 2000/ Windows XP
over TCP/IP (LPR) 102
Adding Printers in Windows 2000/Windows XP
using the Microsoft LPR Monitor 109
5
6
Table of Contents
AXIS 5570e/AXIS 5670e User’s Manual
Adding Printers in Windows NT 4 Using the
Microsoft LPR Monitor 112
AXIS Print Monitor Software 114
Adding Printers over TCP/IP in Windows NT 4
using AXIS Print Monitor 115
Adding NetBIOS/NetBEUI Printers in Windows
2000 using AXIS Print Monitor 116
Adding Printers over NetBIOS/NetBEUI in
Windows NT 4 using AXIS Print Monitor 117
Adding Printers in Windows 98 and Me over
TCP/IP using AXIS Print Monitor 119
Adding Printers in Windows 98 and Me over
NetBIOS/NetBEUI using AXIS Print Monitor 121
122
Section 7
Setting Up - NetWare 123
Setup using NDPS 124
Setup using iPrint 143
Basic Setup with AXIS NetPilot 149
Advanced Installation using AXIS NetPilot 150
Basic Queue-based printing over IP 153
Section 8
Setting Up - Macintosh 158
Installation in Mac OS X 158
Installation on MacOS 9.1 or older, using
AppleTalk 159
Choosing a Printer 160
Section 9
Setting Up - UNIX 165
Print Tools 165
Typical Invocation via a Windows Manager 167
Typical Invocation from a Terminal Window 167
Debian 3.0 168
Red Hat 7.3 169
SuSE 8.0 172
AXIS axinstall Script 173
Print Methods on TCP/IP Networks 176
AXIS 5570e/AXIS 5670e User’s Manual
Table of Contents
Section 10
Management and Configuration 180
Using a Web browser 181
Using AXIS ThinWizard for Print Server
Management 189
Using FTP for Print Server Management 192
Using Telnet 195
Using SNMP 199
Using Novell Utilities 201
Configuring the Print Server from an IBM host
203
Section 11
Configuration Possibilities 205
Autodetect Printer Type 205
AutoIP 206
E-mail Notification 206
IPP (Internet Printing Protocol) 207
Logical Printers for Customized Printing 220
Network Speed 230
NetWare Packet Signature
Level 1,2,3 230
Flash Loading of Firmware over the Web 230
Secure Web Services — SSL/TLS 231
Section 12
Upgrading the Firmware 236
Upgrading the Firmware 236
Obtaining the Software 239
Section 13
SNA Parameter Overview 240
Communication Parameters 240
Updating parameters 243
Auto-configuration and Mapping 245
Section 14
SNA Gateways 247
Section 15
Extended IBM Printer Emulation 251
Section 16
IBM Fonts 255
Section 17
IBM Print Formatting 262
7
8
Table of Contents
AXIS 5570e/AXIS 5670e User’s Manual
Section 18
IPDS Overview 268
IPDS Parameter Settings 268
IPDS System Languages 268
IPDS Fonts 276
Printer Resident Fonts 276
Immediate Font Substitutions 277
Unsupported Fonts 277
Typographical Fonts 278
Section 19
DBCS Support 279
Configuring the AS/400 Host, 5494 CU mode
279
Configuring the AXIS 5570e/AXIS 5670e 280
Verifying the Communications Link 281
Amending Device Features 282
Extended IBM Printer Emulation 283
Font Tables 283
Section 20
Digital Copier Support 286
Section 21
Test Button 288
Section 22
Technical Specifications 290
Section 23
The Parameter List 295
AXIS 5570e: 295
AXIS 5670e: 324
Section 24
Glossary 362
AXIS 5570e/AXIS 5670e User’s Manual
Section 1
Section 1: Introduction
Introduction
Product Model Summary
The AXIS 5570e/AXIS 5670e is a LAN attached multi-protocol print
server that prints IBM and ASCII data streams to any ASCII printer.
Supporting IBM Mainframes, AS/400, NetWare, UNIX, LAN Server
Manager, Windows and Apple EtherTalk, these products are ideal for
IBM Mainframe and AS/400 sites that are migrating from pure IBM
networks to LAN environments.
9
10
Section 1: Introduction
AXIS 5570e/AXIS 5670e User’s Manual
Where to use it
Supported
Environments
The AXIS 5570e/AXIS 5670e is the ideal print server in mixed
environments as it can communicate with all the major computer
systems and network protocols including:
•
IBM Mainframe and AS/400
•
Windows
•
NetWare
•
UNIX
•
Windows clients connected to LANtastic networks
•
Macintosh
•
Internet via any standard Web browser
AXIS 5570e/AXIS 5670e User’s Manual
Section 1: Introduction
How to use it
Installation and
Integration
The installation of the AXIS 5570e/AXIS 5670e and its integration
into the network is performed using the appropriate client software,
provided with your print server or your operating system.
Note:
The AXIS 5570e/AXIS 5670e is designed for 10 Mbps Ethernet and 100 Mbps Fast
Ethernet networks and connects to the network via a twisted pair RJ45 category 5
cable (10baseT and 100baseTX).
Configuration and
Management
As the AXIS 5570e/AXIS 5670e comprises a built-in Web server, it
can be configured and managed directly from its internal Web pages,
using HTTP or HTTPS over TCP/IP.
Access to the AXIS 5570e/AXIS 5670e via any standard Web browser,
offers you a platform-independent management tool that is suitable
for all supported network environments.
Refer to the Parameter List document on www.axis.com for a
complete description of the Axis print server parameters.
11
12
Section 1: Introduction
AXIS 5570e/AXIS 5670e User’s Manual
AXIS 5570e/AXIS 5670e Features and Benefits
Reliability
The AXIS 5570e/AXIS 5670e print server provides high performance
and reliability combined with low power consumption. The electronic
circuits are based on the AXIS ETRAX 100LX chip, which comprises an
integrated 32 bit RISC processor and associated network controllers.
Flexibility
In the IBM Mainframe and AS/400 environment, the AXIS 5570e/AXIS
5670e can emulate IBM twinax and coax print and control
functionality. This means that the AXIS 5570e/AXIS 5670e can
effectively replace coax/twinax attached printers and control units
on the LAN.
It supports printing in all the major computer systems and
environments, including five different print methods in the TCP/IP
environment
.Speed
Easy to Install
Security
The AXIS ETRAX 100LX chip has been specifically designed for LAN
products. High speed Centronics communication such as ECP,
Hewlett-Packard Fast Mode, High Speed and IBM Fast Byte is
supported.
You can install the AXIS 5570e/AXIS 5670e in minutes, using a
standard web browser.
You can assign a password to restrict login and printer access, disable
protocols and force a secure mode over https. See “Secure Web
Services — SSL/TLS” on page 231.
AXIS 5570e/AXIS 5670e User’s Manual
Monitoring
Section 1: Introduction
The internal AXIS 5570e/AXIS 5670e Web pages allow you to
continuously monitor printer status. Integrity of your printing is also
monitored via interactive communication with the IBM host.
The AXIS Print Monitor for Windows 98, Windows Me and Windows
NT can be configured to display pop-up messages that show the
status of peer-to-peer print jobs.
The AXIS 5570e/AXIS 5670e additionally supports SNMP for remote
monitoring.
Futureproof
You can upgrade the AXIS 5570e/AXIS 5670e Flash memory over FTP,
via the print server’s web interface or using AXIS ThinWizard
software.
This allows you to quickly update and enhance the operational
features of your AXIS 5570e/AXIS 5670e when new print server
software becomes available. See “Upgrading the Firmware” on
page 236.
13
14
Section 2: Product Overview
Section 2
AXIS 5570e/AXIS 5670e User’s Manual
Product Overview
Unpack and check all the items using the following check list.
Contact your dealer if anything is missing or damaged. All packing
materials are recyclable
Hardware Inventory
Item
AXIS 5570e
Model/Title
TCP/IP
IPDS SNA
TCP/IP
IPDS SNA
Country
Part number
0188
0193
0189
0194
Europe
19108
UK
19109
Australia
19111
USA/Japan
19110
CD
AXIS Product CD
rev 1.3 or later
Printed Material
AXIS 5570e/AXIS 5670e User’s Guide
20896
Adhesive Holder &
Clip*
USB Cable*
ACC AXIS 5500 CLIPS K
20119
70 cm
20208
AXIS 5670e
Power Supply Type
(PS-H)
* Only supplied with AXIS 5570e.
AXIS 5570e/AXIS 5670e User’s Manual
Section 2: Product Overview
Protocols and Datastreams
The AXIS 5570e/AXIS 5670e are available in two versions; IPDS SNA
and TCP/IP.
The table below displays the functionality of each version.
AXIS 5570e
IPDS support
SCS support
3270DS support
TN3270E
TN5250E
SNA support
Digital Copier Support
AXIS 5670e
IPDS support
SCS support
3270DS support
TN3270E
TN5250E
SNA support
Digital Copier Support
IPDS SNA (part no. 0193) TCP/IP (part no. 0188)
.
.
.
.
.
.
.
.
.
.
.
IPDS SNA (part no. 0194) TCP/IP (part no. 0189)
.
.
.
.
.
.
.
.
.
.
.
Note:
All models may not be available in all countries in which Axis operates. Please
contact your local sales representative for more information.
15
16
Section 2: Product Overview
AXIS 5570e/AXIS 5670e User’s Manual
The AXIS 5570e Network Print Server
LPT1
Test Button
Network Indicator
USB1
Ethernet Connector
Power Connector
Power Indicator
The AXIS 5670e Network Print Server
Power
Indicator
COM1
Network
Indicator
LPT1
LPT2
Test button
Ethernet Connector
Power Connector
AXIS 5570e/AXIS 5670e User’s Manual
Section 2: Product Overview
Backside label on print
server
Serial number
Printer Ports
AXIS 5570e is equipped with one USB port that is USB 1.1 and 2.0
low and full speed compliant, and one high-speed IEEE 1284
compatible parallel port
AXIS 5670e is equipped with two high-speed IEEE 1284 compatible
parallel ports and one RS232 serial port.
Test Button
The test button is used for:
• printing a test page to check the connection to the printer
• printing the parameter list showing the print server settings
• performing a Factory Default of the print server, which will
restore all parameters and settings to their factory default values.
See Performing a Factory Default, on page 288
Network Connector
Network Indicator
The AXIS 5570e/AXIS 5670e are designed for 10baseT Ethernet or
100base TX Fast Ethernet networks and is connected to the network
via a standard RJ-45 (Category 5 twisted pair) cable.
The network indicator flashes to indicate network activity.
17
18
Section 2: Product Overview
AXIS 5570e/AXIS 5670e User’s Manual
Power Indicator
The power indicator is lit while power is applied. If it is not lit, or if it
flashes, there is a problem with the print server or its Power Adapter.
Configuration and
Management
The print server can be configured and managed from its internal
Web pages, using HTTP as well as HTTPS in the secure mode. The print
server’s internal Web pages offer you a platform independent
management tool that is suitable for all supported network
environments. See Using a Web browser, on page 181
AXIS Product CD
The AXIS Product CD provides an easy-to-use electronic catalog, that
includes Axis software, user documentation, etc. All documents
presented on the CD are in PDF format.
Note:
If Adobe Acrobat Reader is not installed on to your computer, you cannot
open pdf files. Go to www.adobe.com to download free Acrobat Reader
software.
Secure Management
Supported Printers
You can assign a password to restrict login and printer access, disable
protocols and force a secure mode over https. See Secure Web
Services — SSL/TLS, on page 231, on page 205
Any standard printer can be connected for network printing, except
host-based printers, e.g. Windows GDI printers.
AXIS 5570e/AXIS 5670e User’s Manual
Section 3
Section 3: Basic Installation
Basic Installation
Getting Started
After you have verified that no items in Product Overview, on page
14, are missing from the package, you are ready to install your AXIS
5570e/AXIS 5670e.
Follow the instructions below to install the AXIS 5570e/AXIS 5670e
in your environment:
1. Start the procedure by connecting the AXIS 5570e/AXIS 5670e to
your network and printer. Refer to Connecting a printer to the
Ethernet Network, on page 20.
2. When the AXIS 5570e/AXIS 5670e is successfully connected,
proceed to the Installation Guide, on page 22, where you will find
further information about how to install and integrate the AXIS
5570e/AXIS 5670e in your network environments.
19
20
Section 3: Basic Installation
AXIS 5570e/AXIS 5670e User’s Manual
Connecting a printer to the Ethernet Network
Follow the instructions below to connect a printer to the network via
the AXIS 5570e/AXIS 5670e print server.
Important:
Make sure that the AXIS 5570e/AXIS 5670e external power supply is marked with
the correct voltage!
1. Switch off the printer(s) and disconnect the AXIS 5570e/AXIS
5670e external power supply.
2. Locate the serial number, found on the backside label of the print
server, and write it down. You will need this number during the
network configuration.
3. Connect the print server to the printer(s).
4. Connect the print server to the network using a twisted pair RJ45
cable (of category 5 or better).
5. Switch on the printer(s) and connect the external power supply
to the AXIS 5570e/AXIS 5670e. The power indicator lights up. If
the network indicator starts to flash, the print server is correctly
connected to the network.
6. Press and release the test button on the print server to print a
test page.
If the print server is correctly connected to the printer(s), a test
page will be printed.
AXIS 5570e/AXIS 5670e User’s Manual
Section 3: Basic Installation
Mounting the AXIS 5570e
Using the supplied clip and holder, the AXIS 5570e can be mounted
e.g. on the back of the printer or on a wall.
Adhesive Clip
Fasten to print
server by peeling
off adhesive tape.
Adhesive Holder
Fasten to
mounting surface
by peeling off
adhesive tape.
The print server can now be installed in your network using one of
the methods detailed in the Installation Guide, on page 22.
Notes:
•
The test page includes a list of the most important parameters, including
the network speed and the firmware version number.
•
Each print server is pre-configured with a unique node address that is
identical to the serial number. The node address can be changed using any
standard Web browser. Please refer to Management and Configuration,
on page 180, for more information.
•
The AXIS 5570e/AXIS 5670e uses high speed Centronics communication.
For use with older printers not supporting high speed, this function can be
disabled by using any standard Web browser. Please refer to Section 10
Management and Configuration, on page 180, for more information.
21
22
Section 3: Basic Installation
AXIS 5570e/AXIS 5670e User’s Manual
Installation Guide
After connecting the AXIS 5570e/AXIS 5670e to your network, you
are now ready to perform the basic setup procedures. The method of
installation that you choose should be dictated by your printing
requirements and the type of network into which you are integrating.
1. Start out with setting an IP address on the print server, described
in Setting the IP address, on page 24.
2. Refer to the table below to determine which setup procedures
that are relevant to your network environment.
Environment
Data
Stream
Network
Configuration
Actions
AS/400
SCS / IPDS
SNA
SNA Printing - 5494 Mode, on page 36
SCS
TN5250E (TCP/IP)
TN5250E printing (SCS over IP), on page 48
IPDS
PPR/PPD (TCP/IP)
PPR/PPD Printing - IPDS data streams, on page 51
SCS / IPDS
SNA
SNA Printing, on page 60
SCS / IPDS
TN3270E (TCP/IP)
TCP/IP TN3270E Printing, on page 70
IPDS
PPR/PPD (TCP/IP)
PPR/PPD Printing - IPDS data streams, on page 82
NetWare
TCP/IP and IPX/SPX
Setting Up - NetWare, on page 123
Windows
98/NT/Me
2000/XP
TCP/IP,
NetBIOS/NetBEUI
Setting Up - Windows, on page 101
Macintosh
TCP/IP, AppleTalk
Setting Up - Macintosh, on page 158
UNIX
TCP/IP
Setting Up - UNIX, on page 165
IBM
Mainframe
AXIS 5570e/AXIS 5670e User’s Manual
Installation Tools
Section 3: Basic Installation
The recommended installation tools and management methods for
the AXIS 5570e/AXIS 5670e are summarized here:
Protocols
Operating Systems
Configuration method
Management method
TCP/IP
Windows 2000/XP
Windows Standard Add
Printer Wizard
Web Browser, FTP, Telnet, SNMP
AXIS ThinWizard
TCP/IP
Windows 98/NT/Me
AXIS Print Monitor software and
Windows Add Printer Wizard
Web Browser, FTP, Telnet, SNMP
TCP/IP
Mac OS X
Native MacOSX tool
Web browser
TCP/IP
UNIX
Native UNix/Linux tools
Web Browser, FTP, Telnet, SNMP
IPX/SPX
NetWare
Novell Utilities
Novell Utilities
NetBIOS
NetBEUI
Windows
95/98/NT/Me/2000
AXIS Print Monitor
Web browser. FTP, Telnet, SNMP
AppleTalk
Macintosh
Web browser, Mac-FTP
Web browser, Mac-FTP
Recommended installation tools for the AXIS 5570e/AXIS 5670e
*
A shareware LPR spooler is available for Windows for
Workgroups. You can download this software from
http://www.axis.com/techsup
23
24
Section 3: Basic Installation
AXIS 5570e/AXIS 5670e User’s Manual
Setting the IP address
Dynamic IP Address
Assignment
Method
Server required
Comment
DHCP
DHCP server
Dynamic assignment of IP addresses.
See Dynamic IP Address Assignment, on page 24
RARP
RARP server
Static assignment of I P adresses. Cannot be used
over routers.
See Dynamic IP Address Assignment, on page 24
BOOTP
BOOTP server
Static assignment of IP addresses.
See Dynamic IP Address Assignment, on page 24
AutoIP
No server required.
Automatic assignment of IP addresses for Windows
environments.
See Dynamic IP Address Assignment, on page 24
Manual IP Address
Assignment
Method
Platform
Windows
AXIS
ThinWizard
See
Requires the IP address for each device
to be downloaded individually.
Cannot be used over routers.
Setting the IP address using
ARP/Ping, on page
28
UNIX/Mac OS X
You must define the Default Router
and Subnet Mask. Log in to the print
server’s web pages and select Admin |
Network Settings | Detailed View |
TCP/IP | Default Router and Subnet
Mask. DHCP, Auto-IP, BOOTP and RARP
must first be set to No
Setting the IP address using
ARP/Ping, on page
28
Windows
Axis software that allows you to find
print servers in your network and assign
an IP address to them.
This software is recommended for small
offices and local networks.
Setting the IP address using AXIS IP
JumpStarter, on
page 27
Windows 2000/XP
Axis software that assists in setting the IP
address of multiple print servers simultaneously. This software is recommended
for large organizations and enerprise networks.
Using AXIS ThinWizard for Print Server
Management, on
page 189
ARP/Ping
AXIS IP
JumpStarter
Comment
AXIS 5570e/AXIS 5670e User’s Manual
Section 3: Basic Installation
Dynamic IP address
Assignment
Obtaining an IP
address through DHCP
•
•
Obtaining an IP
Address through
AutoIP
Important:
If you have a DHCP server on your network, your print server
will receive an IP address automatically. The IP address will then
appear on the test page printed when you press the test button
once.
You should now be able to access the print server’s internal web
pages as described on Accessing the Web Pages, on page 182
If you are not working in a DHCP network, you need to set the
IP address of the print server manually. See “Manual IP Address
Assignment” on page 24.
AutoIP may be used to set the IP address automatically in the
absence of a DHCP server.
The default AutoIP address structure is: 169.254.xxx.xxx.
The AutoIP function will only function when the DHCP parameter
is enabled in the print server.
This function is enabled automatically upon installation of a brand
new print server. If you perform a Factory Default using the test
button on the print server and you do not have a DHCP server on your
network, AutoIP will automatically set the IP address of the print
server.
The DHCP Enabled parameter is enabled/disabled in the print server’s
web pages: Admin => Network Settings => Detailed View =>
TCP/IP => DHCP Enabled: Yes/No.
25
26
Section 3: Basic Installation
AXIS 5570e/AXIS 5670e User’s Manual
Notes:
Manual IP address
assignment
•
Use a Web browser with JavaScript support and Java enabled.
•
The AXIS 5570e/AXIS 5670e supports WINS (Windows Internet Name
Service), which is recommended when setting the IP address using DHCP in
Windows environments.
•
If you are working in a WINS/ DDNS network, you can access the print
server’s web pages using its default host name: In the Web browser’s
Location/Address field, enter the default print server name AXISxxxxxx
(xxxxxx are the last six digits of the serial number, found on the print
server’s underside label). Example: If the serial number is 00 40 8c 18 16
36, type AXIS181636 and press Enter.
•
DHCP, RARP and BOOTP can be used to set the IP address in UNIX.
•
If you are working in a network that does not use dynamic IP address
assignment, refer to Manual IP address assignment, on page 26 to assign
an IP address to the print server manually.
To establish communication with the TCP/IP network, an IP Address
must be assigned to your AXIS 5570e/AXIS 5670e. Choose the
appropriate method according to your network:
• AXIS IP JumpStarter™ software is an easy-to-use Windows
application that allows you to assign an IP address to your
print server and find print servers already installed in your
network. Refer to Setting the IP address using AXIS IP JumpStarter, on
page 27.
• ARP/Ping - use this method to set the IP address for each
new print server individually.
This method cannot be used over routers.
Refer to Setting the IP address using ARP/Ping, on page 28.
• AXIS ThinWizard™ software is the primary recommended tool
for large organizations.
It can set IP addresses, discover and group print servers,
install new firmware and configure multiple Axis products
concurrently.
Refer to Using AXIS ThinWizard for Print Server Management,
on page 189
AXIS 5570e/AXIS 5670e User’s Manual
Section 3: Basic Installation
Note:
If you are using host names, you can map a unique host name to the IP address.
Refer to your system manuals for instructions on how this is performed on your
system.
Setting the IP address
using AXIS IP
JumpStarter
First, install AXIS IP JumpStarter which is available free of charge on
www.axis.com
1. Select the required server from the serial number list in the IP
JumpStarter dialog window.
Server menu
2. From the Server menu, select Set IP Address.
3. Click the radio button that corresponds to your choice of IP
setting method.
4. Click OK to save your settings.
5. Enter the server root password (by default set to pass), and click
OK.
6. The AXIS 5570e/AXIS 5670e will appear in the list with the
assigned IP address.
27
28
Section 3: Basic Installation
AXIS 5570e/AXIS 5670e User’s Manual
7. To access the print server’s web pages, highlight the AXIS
5570e/AXIS 5670e in the list and select Server Home Page from
the Server menu.
Note:
If your print server does not appear in the serial number list, refer to the AXIS IP
JumpStarter online help files.
Setting the IP address
using ARP/Ping
Refer to the appropriate section below to assign an IP address to your
AXIS 5570e/AXIS 5670e using ARP/Ping:
Windows
Open a Command Prompt and enter the following syntax:
1.
2.
Syntax
arp -s <Internet address> <Ethernet address>
ping <Internet address>
Example
arp -s 192.168.3.191 00-40-8c-18-16-36
ping 192.168.3.191
The host will return reply from 192.168.3.191, or a similar message.
This indicates that the address has been set and that communication
is established. You are now ready to print.
UNIX, Mac OS X
Open a Terminal and enter the following syntax:
1.
2.
Syntax
arp -s <Internet address> <Ethernet address>
ping <Internet address>
Example
arp -s 192.168.3.191.00:40:8c:18:16:36
ping 192.168.3.191
The host will return psname is alive, or a similar message. This
indicates that the address has been set and that communication is
established. You are now ready to print.
Important!
You must define the Default Router and Subnet Mask when you set a static
IP address. Log in to the print server’s web pages and select Admin |
Network Settings | Detailed View | TCP/IP | Default Router and Subnet
Mask.
DHCP, Auto-IP, BOOTP and RARP must first be set to No!
AXIS 5570e/AXIS 5670e User’s Manual
Section 3: Basic Installation
Notes:
Using RARP in UNIX
•
The Ethernet address is equal to the serial number, which is located on the
underside label of the AXIS 5470e.
•
The ARP command varies between different UNIX systems. Some BSD type
systems expect the host name and node address in reverse order.
Furthermore IBM AIX systems will require the additional argument ether.
Example:
arp -s ether <host name> 00:40:8c:10:00:86 temp
•
When you execute the ping command for the first time, you may experience
a significantly longer response time than usual.
Follow the instructions below to set the IP address using RARP:
1. Append the following line to your Ethernet Address table. This is
typically located in the /etc/ethers file:
<Ethernet address> <host name>
Example:
00:40:8c:10:00:86 npsname
2. Update, if necessary, your host table and alias name databases,
as required by your system.
3. If it is not already running, start the RARP daemon. This is
typically performed using the rarpd -a command.
4. Restart the AXIS 5570e/AXIS 5670e to download the IP address.
Notes:
•
The Ethernet address is equal to the serial number, which can be found on
the underside label of the AXIS 5570e/AXIS 5670e.
•
If you are a IBM AIX user, you will probably not have access to a RARP
daemon. If this is the case, you can use either the ARP or BOOTP methods
instead.
29
30
Section 3: Basic Installation
Using BOOTP
in UNIX
AXIS 5570e/AXIS 5670e User’s Manual
Follow the instructions below to set the IP address using BOOTP:
1. Append the following entry to your boot table. This is typically
performed by editing the file: /etc/bootptab
<host name>:ht=<hardware type>:vm=<vendor magic>:\
:ha=<hardware address>:ip=<IP address>:\
:sm=<subnet mask>:gw=<gateway field>
Example:
npsname:ht=ether:vm=rfc1048:\
:ha=00408c100086:ip=192.168.3.191:\
:sm=255.255.255.0:gw=192.168.1.1
The AXIS 5570e/AXIS 5670e can automatically download a
customized config file from a TFTP server. Just add the name of the
config file and the TFTP server’s IP address to your boot table. The
config file is downloaded immediately after the AXIS 5570e/AXIS
5670e receives its IP address.
AXIS 5570e/AXIS 5670e User’s Manual
Section 3: Basic Installation
Notes:
•
The AXIS 5570e/AXIS 5670e supports WINS (Windows Internet Name
Service), which is recommended when setting the IP address using DHCP in
Windows environments.
•
The Ethernet Address is the same as the serial number, found on the print
server’s underside label. Enter the Ethernet Address in the same format as
in the example above.
•
Setting the IP address with arp and ping is only possible in the first ten
minutes after re-booting the print server.
•
When you execute the ping command for the first time, you may
experience a significantly longer response time than usual.
•
The arp command varies between different UNIX systems.
•
You need root privileges on your UNIX system in order to execute the arp
command and run axinstall .
•
Some BSD type systems expect the host name and serial number in reverse
order. Furthermore IBM AIX systems will require the additional argument
ether.
Example: arp -s ether <host name> <Ethernet Address> temp
31
32
Section 3: Basic Installation
Managing DHCP
AXIS 5570e/AXIS 5670e User’s Manual
Follow the instructions below to download the IP address using
DHCP:
1. Edit or create a scope in the DHCP manager of the DHCP
daemon. The entries included in this scope should contain the
following parameters:
• range of IP addresses
• subnet mask
• default router IP address
• WINS server IP address(es)
• lease duration
2. Activate the scope.
The AXIS 5570e/AXIS 5670e will automatically download the DHCP
parameters.
If you are using WINS, you must include at least one WINS server IP
address in the DHCP scope. Immediately after the IP address has been
received, the AXIS 5570e/AXIS 5670e registers its host name and IP
address on the WINS server.
The AXIS 5570e/AXIS 5670e can automatically download a
customized config file from a TFTP server. Just add the name of the
config file and the TFTP server’s IP address to your DHCP scope. The
config file is downloaded immediately after the AXIS 5570e/AXIS
5670e receives its IP address.
System privileges
You need root privileges on your UNIX system, or administrator
privileges on a Windows NT server.
Ethernet address
You need to know the Ethernet address of your AXIS 5570e/AXIS
5670eto perform the installation. The Ethernet address is based upon
the serial number of your print server.
This means, for example, that a print server with the serial number
00408C100086, will have the corresponding Ethernet address of 00
40 8C 10 00 86. The serial number is located on the backside label of
the print server.
AXIS 5570e/AXIS 5670e User’s Manual
IP address
Section 3: Basic Installation
If you do not have a DHCP server on your network, you must obtain
an unused IP address from your network administrator.
Important:
DO NOT use the IP addresses used in the following examples when installing your
AXIS 5570e/AXIS 5670e. Always consult your network administrator before
assigning an IP address to your AXIS 5570e/AXIS 5670e.
Registering and
Resolving
Host Names
In order to register the host name of the AXIS 5570e/AXIS 5670e in
networks with dynamic IP address settings, WINS (Windows Internet
Name Service) and DDNS (Dynamic Domain Naming System) are
supported. It is recommended that at least one of these methods be
used when setting the IP address of the AXIS 5570e/AXIS 5670e
using DHCP.
The host name of the AXIS 5570e/AXIS 5670e is specified by the
PS_NAME parameter. Refer to The Parameter List, on page 295.
WINS host name rules
WINS only supports 15 character long host names. If your host name
is longer than 15 characters, the AXIS 5570e/AXIS 5670e truncates
the host name to 15 characters when registering with a WINS server.
You can view the AXIS 5570e/AXIS 5670e host name that is
registered at a WINS server, in the print server’s Web interface. Refer
to Section 10 Management and Configuration, on page 180.
DDNS host name rules
DDNS supports 53 character long host names, but they can only
consist of the characters ‘A-Z’, ’a-z’ and ‘-’. If your host name consists
of any other characters, they are converted to ‘-’, when registering
with a DDNS server. You can view the AXIS 5570e/AXIS 5670e host
name that is registered at a DDNS server, in the print server’s Web
interface. Refer to Section 10 Management and Configuration, on
page 180.
If the host name matches another entry in the DDNS data base, the
AXIS 5570e/AXIS 5670e deletes the entry before registering.
33
34
Section 3: Basic Installation
AXIS 5570e/AXIS 5670e User’s Manual
Notes:
•
The host name limitations conclude that if you want to register the same
host name at a WINS server and a DDNS server, the host name should be no
longer than 15 characters and it should only contain the characters:
‘A - Z’, ‘a-z’ and ‘-’
•
Refer to your system manuals or to your network administrator for
instructions on how host name resolutions are performed on your system.
•
If the host name has not been mapped to the IP address, you can still
perform the following instructions on how to download the IP address. In
this case, simply replace the host name entry with the IP address wherever
required.
AXIS 5570e/AXIS 5670e User’s Manual
Section 4
Section 4: Setting Up - AS/400 (iSeries)
Setting Up - AS/400 (iSeries)
This section describes how to configure the AXIS 5570e/AXIS 5670e
for printing SCS and IPDS data streams using SNA and TCP/IP
transport protocols in the AS/400 (iSeries) environment.
Note:
SNA is only available for print server models with the SNA option installed.
Please refer to Product Model Summary, on page 9
A number of protocols and print methods are available. Looking at
SCS over TCP/IP printing, we strongly recommend the TN5250E
alternative. This print method offers superior control and
management features as well as automatic configuration and high
throughput using the AXIS 5570e/AXIS 5670e.
If you have decided to use SNA, we recommend the 5494 mode.
Compared to the 3174 mode, this alternative yields better text
formatting options as well as automatic configuration.
Proceed to the setup section that is relevant to your network
environment, as described in the table below:
Printing
protocol
SNA - 5494
Mode
Data
streams
SCS
IPDS
Action
Comment
SNA Printing - 5494 Mode, on
page 36
Recommended method
for SNA
TN5250E
(TCP/IP)
SCS
TN5250E printing (SCS over IP), on
page 48
Recommended method
for SCS over TCP/IP
PPR/PPD
(TCP/IP)
IPDS
PPR/PPD Printing - IPDS data streams,
on page 51
Recommended method
for IPDS over TCP/IP
35
36
Section 4: Setting Up - AS/400 (iSeries)
AXIS 5570e/AXIS 5670e User’s Manual
If you intend to operate your AXIS 5570e/AXIS 5670e in a multiprotocol environment, you should also proceed to the other relevant
sections in this manual:
Section 5 Setting Up - IBM Mainframe (zSeries), on page 59
Section 7 Setting Up - NetWare, on page 123
Section 6 Setting Up - Windows, on page 101
Section 8 Setting Up - OS/2, on page 117
Section 8 Setting Up - Macintosh, on page 158
Section 9 Setting Up - UNIX, on page 165
SNA Printing - 5494 Mode
The 5494 mode provides a significantly richer set of features for
formatting text and is the recommended emulation mode in AS/400
environments.
The 5494 mode supports DBCS which accommodates printing from
AS/400 host systems using languages that employ double-byte
character sets, namely Chinese, Japanese and Korean. Refer to DBCS
Support, on page 279 for further information.
The AXIS print server supports printing SCS and IPDS data streams via
the SNA transport protocol.
Note:
SNA is only available for print server models with the SNA option installed.
Please refer to Product Model Summary, on page 9.
Configuring for SNA printing in 5494 Mode is described in three
separate stages:
•
The AS/400 Host System Checklist
•
Configuring the AXIS 5570e/AXIS 5670e
•
Verifying the communication
AXIS 5570e/AXIS 5670e User’s Manual
The AS/400 Host
System Checklist
Section 4: Setting Up - AS/400 (iSeries)
If you are using AS/400 Version 3 Release 1 or higher, the AS/400
host in 5494 CU mode is automatically configured. The instructions in
this section describe this automated configuration procedure.
If you are using a pre-version 3 release, you must perform the
configuration procedure manually. If this is the case, please refer to
the Axis Web site for further documentation.
Note:
You will find an AS/400 Parameter checklist in the AXIS 5570e/AXIS 5670e
User’s Guide where you can enter the values described in this section for future
reference.
1. Type DSPNETA on the AS/400 command line and press Enter.
For future reference, note the values of the Local network
ID and Default local location parameters. Press F3.
Example:
DSPNETA
Display Network Attributes
System:
S1032BB0
Current system name . . . . . . . . . .
Pending system name . . . . . . . . . .
Local network ID . . . . . . . . . . . .
Local control point name . . . . . . . .
Default local location . . . . . . . . .
Default mode . . . . . . . . . . . . . .
APPN node type . . . . . . . . . . . . .
Data compression . . . . . . . . . . . .
Intermediate data compression . . . . .
Maximum number of intermediate sessions
Route addition resistance . . . . . . .
Server network ID/control point name . .
*ANY
Press Enter to continue.
F3=Exit
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
:
S1032BB0
:
: > APPN
:
S1032BB0
: > S1032BB0
:
BLANK
:
*ENDNODE
:
*NONE
:
*NONE
:
200
:
128
:
*LCLNETID
More...
F12=Cancel
The required parameter values are highlighted in bold.
2. Type WRKLIND *ELAN and press Enter:
to get a list of all line descriptions on the system. Type 5 in front
of the line description and press Enter.
37
38
Section 4: Setting Up - AS/400 (iSeries)
AXIS 5570e/AXIS 5670e User’s Manual
3. Press F11 to display keywords.
Display Line Description
S44A6643
Line description . . .: LIND
Option . . . . . . . .: OPTION
Category of line . . .:
Resource name . . . .:
Online at IPL . . . . :
Vary on wait . . . . .:
Network controller . .:
Local adapter address :
Exchange identifier . :
Ethernet standard . .:
Line speed . . . . . .:
Enable only for TCP/IP:
Current line speed . .:
Duplex . . . . . . . .:
Current duplex . . . .:
Maximum controllers. .:
RSRCNAME
ONLINE
VRYWAIT
NETCTL
ADPTADR
EXCHID
ETHSTD
LINESPEED
TCPONLY
DUPLEX
MAXCTL
Press Enter to continue.
F3=Exit
F11=NonDisplay keywords
ETHLINE
*BASIC
*ELAN
LIN061
*YES
*NOWAIT
ETHLINET
08005AB77D49
056A6643
*ALL
10M
*NO
10M
*HALF
*HALF
50
More...
F12=Cancel
AXIS 5570e/AXIS 5670e User’s Manual
Section 4: Setting Up - AS/400 (iSeries)
4. For future reference, note the values of the Local Adapter
Address (ADPTADR) and Maximum Controllers
(MAXCTL) parameters. Press Enter to view the active switched
controllers display.
Display Line Description
Line description . . : LIND
Option . . . . . . . : OPTION
Category of line . . :
S44A6643
ETHERNET
*ACTSWTCTL
*ELAN
--------------Active Switched Controllers-------CONTROLER1
CONTROLER2
CONTROLER3
Press Enter to continue.
F3=Exit
F11= Nondisplay keywords
Bottom
F12=Cancel
39
40
Section 4: Setting Up - AS/400 (iSeries)
AXIS 5570e/AXIS 5670e User’s Manual
5. Press Enter to display the SSAP list. Make sure that there is at
least one SSAP entry dedicated for SNA. For your future
reference, note the SSAP value for this entry.
Verify that the number of controllers displayed on this screen
does not exceed the value for maximum controllers (MAXCTL)
from above.
Display Line Description
S44A6643
Line description .: LIND
Option . . . . . : OPTION
Category of line .:
SSAP List. . . . .: SSAP
----Source Service Access
SSAP
Maximum Frame
04
1496
12
1496
AA
1496
C8
1496
08
1496
ETHLINE
*SSAP
*ELAN
Points-----Type
*SNA
*NONSNA
*NONSNA
*HPR
*SNA
Press Enter to continue.
F3=Exit
F11=Nondisplay keywords
Note:
The SNA entry is normally set to SSAP 04.
Bottom
F12=Cancel
AXIS 5570e/AXIS 5670e User’s Manual
Section 4: Setting Up - AS/400 (iSeries)
6. Press Enter to display the Autocreate controller
(AUTOCRTCTL) parameter. Ensure that the AUTOCRTCTL
parameter is set to *YES. Press F3 to return to the command
line.
Display Line Description
S44A6643
Line description . . :
Option . . . . . . . :
Category of line . . :
LIND
OPTION
ETHERNET
*APPN
*ELAN
Link speed . . . . .:
Cost/connect time . .:
Cost/byte . . . . . :
Security for line. . :
Propagation delay. . :
User-defined 1 . . . :
User-defined 2 . . . :
User-defined 3 . . . :
Autocreate controller:
Autodelete controller:
LINKSPEED
COSTCNN
COSTBYTE
SECURITY
PRPDLY
USRDFN1
USRDFN2
USRDFN3
AUTOCRTCTL
AUTODLTCTL
10M
0
0
*NONSECURE
*MIN
128
128
128
*YES
1440
Press Enter to continue.
F3=Exit
Bottom
F11=Nondisplay keywords
F12=Cancel
7. Type DSPSYSVAL QCHRID on the command line and press
Enter. Note the code page for future reference. Press F3 to exit.
8. Type DSPSYSVAL QAUTOCFG on the command line and press
Enter. Make sure the Autoconfigure device parameter is
turned on (1). Press F3 to exit.
Display System Value
System value . . . . . :
Description . . . . . :
QAUTOCFG
Autoconfigure devices
Autoconfigure device . :
1
0=Off
1=On
41
42
Section 4: Setting Up - AS/400 (iSeries)
AXIS 5570e/AXIS 5670e User’s Manual
9. Type DSPSYSVAL QAUTORMT on a command line and press
Enter. Make sure the Autoconfigure remote
controller parameter is turned on(1). Press F3 to exit.
Display System Value
System value . . . . . :
Description . . . . . :
QAUTORMT
Autoconfigure of remote controllers
Autoconfigure remote controller :
1
0=Off
1=On
10. Type DSPMODD QRMTWSC on the command line and press
Enter. Press F11 to display the keywords. Verify that the mode
description exists on the system and that it is configured as
presented in the example below. Use the command
WRKMODD QRMTWSC if you need to change a value.
Press F3.
Display
Mode
Mode
Description
description
.
.
.
.
S44A6643
.
.
.
:MODD
QRMTWSC
Class-of-service . . . . . . . :COS
Maximum sessions . . . . . . . :MAXSSN
Maximum conversations. . . . . :MAXCNV
Locally controlled sessions. . :LCLCTLSSN
Pre-established sessions. . . .:PREESTSSN
Maximum inbound pacing value. .:MAXINPAC
Inbound pacing value . . . . . :INPACING
Outbound pacing value
. . . . :OUTPACING
Maximum length of request unit.:MAXLENRU
Data compression . . . . . . . :DTACPR
Inbound data compression . . . :INDTACPR
Outbound data compression
. . :OUTDTACPR
Session level encryption . . . :SLE
Text . . . . . . . . . . . . . :TEXT
is IBM Supplied
Press
F3=
Enter
Exit
to
continue.
F11=Nondisplay
#CONNECT
57
57
56
0
*CALC
7
7
*CALC
*NETATR
*RLE
*RLE
*NONE
This Mode
Bottom
keywords
F12=Cancel
AXIS 5570e/AXIS 5670e User’s Manual
Section 4: Setting Up - AS/400 (iSeries)
11. Type DSPUSRPRF QUSER and press Enter. Make sure that the
QUSER Status is *ENABLED.
Display User Profile - Basic
User profile . . . . . . . .
Previous sign-on . . . . . .
Sign-on attempts not valid .
Status . . . . . . . . . . .
Date password last changed .
Password expiration interval
Set password to expired . .
User class . . . . . . . . .
Special authority . . . . .
Group profile . . . . . . .
Owner . . . . . . . . . . .
Group authority . . . . . .
Group authority type . . . .
Supplemental groups . . . .
Assistance level . . . . . .
Current library . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
QUSER
0
*ENABLED
08/08/00
*SYSVAL
*NO
*USER
*NONE
*NONE
*USRPRF
*NONE
*PRIVATE
*NONE
*SYSVAL
*CRTDFT
More...
12. Page forward to the next screen by pressing Enter and verify that
the Maximum Storage Allowed parameter is set to
*NOMAX. Press F3.
Display User Profile - Basic
User profile . . . . . . . . . . . . . . . :
QUSER
Initial program .
Library . . . .
Initial menu . . .
Library . . . .
Limit capabilities
Text . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
:
:
:
:
:
:
*NONE
Display sign-on information
Limit device sessions . . .
Keyboard buffering . . . . .
Maximum storage allowed . .
Storage used . . . . . . .
Highest scheduling priority
Job description . . . . . .
Library . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
:
:
:
:
:
:
:
:
*SYSVAL
*SYSVAL
*SYSVAL
*NOMAX
832
3
QDFTJOBD
QGPL
More...
Press Enter to continue.
F3=Exit
F12=Cancel
.
.
.
.
.
.
MAIN
*LIBL
*NO
Work Station User
43
44
Section 4: Setting Up - AS/400 (iSeries)
AXIS 5570e/AXIS 5670e User’s Manual
Use the command WRKCFGSTS *CTL xxxx* (where xxxx is the
first 4 characters of the AXIS 5570e/AXIS 5670e 5494 LU
Name)and press Enter to delete any previously created Controller
and Device descriptions specific to your AXIS 5570e/AXIS 5670e.
Delete the Device Descriptions (indented text) first and then the
Controllers. Print a test page if you are unsure of the AXIS
5570e/AXIS 5670e 5494 LU Name.
Work with Configuration Status
Position to
. . . . .
S1032BB0
Starting characters
Type options, press Enter.
1=Vary on
2=Vary off
5=Work with job
8=Work with description
9=Display mode status
13=Work with APPN status...
Opt
Description
FSIOP
ETHERNET
AXIS11
AXIS11
AXIS11
AXIS11
AXIS11
AXIS11
Status
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE/TARGET
ACTIVE/SOURCE
ACTIVE/SOURCE
ACTIVE/SOURCE
-------------Job--------------
SHEILA
SHEILA
SHEILA
SHEILA
QUSER
QUSER
QUSER
QUSER
010190
010190
010190
010190
AXIS 5570e/AXIS 5670e User’s Manual
Configuring the
AXIS 5570e/AXIS
5670e
Section 4: Setting Up - AS/400 (iSeries)
To perform the instructions presented in this section, you should first
assign an IP address to your AXIS 5570e/AXIS 5670e using one of the
methods presented in Setting the IP address, on page 24.
After you have completed the procedures in the AS/400 Host system
checklist above, follow the instructions below to configure the AXIS
5570e/AXIS 5670e for SNA printing in the AS/400 environment using
a Web browser:
1. Start a Web browser, e.g. Internet Explorer or Netscape
Navigator.
2. Enter the IP address or the host name of the AXIS 5570e/AXIS
5670e in the location field and press the Enter key on your
keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e
will appear.
Note:
To protect the Admin pages and the Configuration Wizard from unauthorized
use, enter a password (default Pass) in the Root Password field under
Admin | General Settings.
3. Click the Configuration Wizard for IBM sessions button.
45
46
Section 4: Setting Up - AS/400 (iSeries)
AXIS 5570e/AXIS 5670e User’s Manual
4. Click the Add Session button. This will start the Configuration
Wizard which is a step-by-step guide through the required IBM
configuration settings.
Notes for SCS printing:
•
In the Configuration Wizard’s IBM Printer Emulation window, 38xx is the
value used for LaserWriter printers and all other values are used for matrix
printers.
•
In the Configuration Wizard Printer Driver window, PCL is used for LaserWriter printers, all other values apply to matrix printers.
Note for IPDS printing:
In the Configuration Wizard, you can choose between PCL or PostScript
printing. Choose the printer language that corresponds to your printer.
AXIS 5570e/AXIS 5670e User’s Manual
Verifying the
Communication Link
Section 4: Setting Up - AS/400 (iSeries)
1. Type WRKCFGSTS *CTL xxxx* on the AS/400 command line
(xxxx is the first four characters of the AXIS 5570e/AXIS 5670e
5494 LU Name)and press Enter. After a couple of minutes,
ensure that the following items are displayed:
•
One APPC controller with the same name as the AXIS
5570e/AXIS 5670e 5494 LU Name.
•
One APPC device with the same name as the AXIS
5570e/AXIS 5670e 5494 LU Name, one controller
session (QRMTWSC) and the currently active printer
sessions (QRMTWSC).
•
One twinax controller named xxxxxRMT, where xxxxx
are the first five characters of the AXIS 5570e/AXIS 5670e
5494 LU Name.
•
One, two or three twinax printer device named
xxxxPRT0z (xxxx are the first four characters of the
AXIS 5570e/AXIS 5670e 5494 LU Name and z is the
printer device number).
The status of all items should now be ACTIVE or VARIED
ON.
2. Type STRPRTWTR xxxxPRT0z on the AS/400 command line
(xxxxPRT0z is the printer device name) and press Enter. This
command starts the writer for this printer device.
3. Press the AXIS 5570e/AXIS 5670e test button once to print a test
page. Ensure that the SNA status is defined on the test page as
Idle, Actv or LU-4.
47
48
Section 4: Setting Up - AS/400 (iSeries)
AXIS 5570e/AXIS 5670e User’s Manual
TN5250E printing (SCS over IP)
TN5250E is the recommended protocol to use when printing SCS data
streams over TCP/IP. This print method offers superior control,
management and throughput for the AXIS 5570e/AXIS 5670e.
Before you begin
Make sure that the AS/400 host is running OS/400 V3R2 or higher
with TCP/IP support installed and configured.
Make sure that the latest PTFs are installed. Information about which
PTFs to use can be obtained from:
http://as400service.rochester.ibm.com/
The AS/400 Host
System Checklist
You will find an AS/400 Parameter checklist in the AXIS 5570e/AXIS 5670e User’s
Guide where you can enter the values described in this section for future
reference.
1. Type WRKCTLD *VWS on the AS/400 command line and press
Enter to determine the number of auto-configured virtual
devices on your AS/400 system. Press F3.
2. Type DSPSYSVAL QAUTOVRT and press Enter. Make sure
that the value of the QAUTOVRT parameter is greater than the
number of auto-configured virtual devices. Press F3.
3. Type DSPSYSVAL QCHRID and press Enter. Note the system
language (code page) for future reference. Press F3.
4. Type WRKTCPSTS OPTION *IFC and press Enter to
determine the IP address of the AS/400 server. Press F3.
AXIS 5570e/AXIS 5670e User’s Manual
Configuring the
AXIS 5570e/AXIS
5670e
Section 4: Setting Up - AS/400 (iSeries)
Follow the instructions below to configure the AXIS 5570e/AXIS
5670e for TN5250E printing using a Web browser:
1. Start a Web browser, e.g. Internet Explorer or Netscape
Navigator.
2. Enter the IP address or the host name of the AXIS 5570e/AXIS
5670e in the location field and press the Enter key on your
keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e
will appear.
Important:
To protect the admin pages and the Configuration Wizard from unauthorized use,
enter a password (default Pass) in the Root Password field under admin | General
Settings.
3. Click the Configuration Wizard for IBM sessions button.
4. Click the Add Session button. This takes you to the
Configuration Wizard which is a step-by-step guide through the
required configuration settings.
49
50
Section 4: Setting Up - AS/400 (iSeries)
AXIS 5570e/AXIS 5670e User’s Manual
Notes:
Verifying the
communication link
•
In the Configuration Wizard, you must choose a new and unused name for
the printer (in the ‘Printer Name’ field) when in the ‘TN5250E Protocol
Configuration’ window.
•
In the Configuration Wizard’s ‘Printer Driver’ window, PCL is used for
LaserWriter printers, all other values apply to matrix printers.
1. Type WRKCFGSTS *DEV xxxx*, where xxxx are the first
four characters of the printer device name, on the AS/400
command line and press Enter. A list of printer devices will be
displayed. Make sure that a virtual printer device is active.
2. Direct a printout to this printer device to check the integrity of
the communication link.
3. Press the test button on the AXIS 5570e/AXIS 5670e once to
print a test page. Make sure that the TN5250E status is defined
on the test page as Idle, Actv or LU-1.
AXIS 5570e/AXIS 5670e User’s Manual
Section 4: Setting Up - AS/400 (iSeries)
PPR/PPD Printing - IPDS data streams
Note:
IPDS is only available for AXIS 5570e/AXIS 5670e models with the IPDS option
installed. For more information, refer to Product Model Summary, on page 9.
The configuration procedures presented in this section are divided
into three separate steps:
• Configuring the AS/400 host
• Configuring the AXIS 5570e/AXIS 5670e
• Verifying the communication between the AXIS 5570e/AXIS
5670e and the AS/400
Before you begin
Make sure that the AS/400 host is running OS/400 V3R6 or higher
with TCP/IP support installed and configured.
Make sure that the latest PTFs are installed. Information about which
PTFs to use can be obtained from:
http://as400service.rochester.ibm.com/
Configuring the
AS/400 Host System
Creating a PSF
Configuration
When configuring the AS/400 host system you can:
•
create a PSF configuration
•
create a printer device description
The system uses default values but you can optionally create a PSF
configuration by following the instructions below:
1. Issue the command CRTPSFCFG.
2. Press F11 to display keywords.
51
52
Section 4: Setting Up - AS/400 (iSeries)
AXIS 5570e/AXIS 5670e User’s Manual
3. Select a name for the PSF configuration and enter it at the PSF
configuration (PSFCFG) line. The name may comprise the
letters A-Z and the numerals 0-9, but must begin with a letter. A
maximum of 10 characters are allowed.
4. Enter QGPL at the Library line.
5. Enter *YES at the IPDS pass through (IPDSPASTHR) line.
6. Enter *NORDYF at the Activate release timer (ACTRLSTMR)
line.
7. Enter *NOMAX at the Release timer (RLSTMR) line.
8. Press the Enter key on your keyboard to create the PSF
configuration.
Many of the settings presented in the following panel example can be
left at their default settings. However, the settings that you must
change are highlighted in bold text and the settings that you must
enter exactly as shown in the example are highlighted in bold
underlined text.
Example:
Create PSF Configuration (CRTPSFCFG)
Type choices, press Enter.
PSF configuration. . . . . . . . PSFCFG
Library
. . . . . . . . . . .
> AXISPR1
> QGPL
User resource library list . . . USRRSCLIBL
*JOBLIBL
Device resource library list . . DEVRSCLIBL
*DFT
+ for more values
IPDS pass through. . . . . . . . IPDSPASTHR
> *YES
Activate release timer . . . . . ACTRLSTMR
> *NORDYF
Release timer. . . . . . . . . . RLSTMR
> *NOMAX
Restart timer. . . . . . . . . . RESTRTMR
*IMMED
APPC and TCP/IP retry count. . . RETRY
15
Delay between APPC retries . . . RETRYDLY
90
Automatic session recovery . . . UAUTOSSNRCY
*NO
Acknowledgment frequency . . . . ACKFRQ
100
Text ‘description’ . . . . . . . TEXT
*BLANK
Bottom
AXIS 5570e/AXIS 5670e User’s Manual
Creating a Printer
Device Description
Section 4: Setting Up - AS/400 (iSeries)
Create a printer device description by following the instructions
below:
1. Issue the command CRTDEVPRT and press Enter.
2. Press F11 to display keywords.
3. Select a name for the printer device and enter it at the Device
Description (DEVD) line. The name may comprise the letters
A-Z and the numerals 0-9, but must begin with a letter. A
maximum of 10 characters are allowed. In the following
instructions the printer device name will be referred to as
AXISPR1.
4. Enter *LAN at the Device class (DEVCLS) line.
5. Enter *IPDS at the Device type (TYPE) line.
6. Enter 0 at the Device model (MODEL) line.
7. Enter *IP at the LAN attachment (LANATTACH) line.
8. Enter a port number at the Port number (PORT) line. The Axis
print server is pre-configured with the port numbers 5001, 5002
and 5003 for IPDS printing.
9. Enter a FGID number at the Font Identifier (FONT) line, e.g.
11 (Courier).
10. Define the Remote location (RMTLOCNAME). Use the IP address
of the AXIS 5470e/670e.
11. (Optional) Enter the name of the previously created PSF
configuration at the User-defined object (USRDFNOBJ):
Object line.
12. (Optional) Enter the library of the previously created PSF
configuration at the User-defined object (USRDFNOBJ):
Library line.
13. (Optional) Enter *PSFCFG at the User-defined object
(USRDFNOBJ): Object type line.
14. Press the Enter key on your keyboard to create the printer device
description.
53
54
Section 4: Setting Up - AS/400 (iSeries)
AXIS 5570e/AXIS 5670e User’s Manual
Many of the settings presented in the following panel example can be
left at their default settings. However, the settings that you must
change are highlighted in bold text and the settings that you must
enter exactly as shown in the example are highlighted in bold
underlined text.
AXIS 5570e/AXIS 5670e User’s Manual
Section 4: Setting Up - AS/400 (iSeries)
Create Device Desc (Printer) (CRTDEVPRT)
Type choices, press Enter.
Device description . . . . . . . DEVD
> AXISPR1
Device class . . . . . . . . . . DEVCLS
> *LAN
Device type
. . . . . . . . . . TYPE
> *IPDS
Device model . . . . . . . . . . MODEL
> 0
LAN attachment . . . . . . . . . LANATTACH
> *IP
Advanced function printing . . . AFP
Port number
. . . . . . . . . . PORT
Online at IPL
. . . . . . . . . ONLINE
Font:
*YES
> 5001
*YES
FONT
Identifier . . . . . . . . . .
Point size . . . . . . . . . .
Form feed. . . . . . . . . . . . FORMFEED
> 11
*NONE
*FILE
Separator drawer . . . . . . . . SEPDRAWER
*FILE
Separator program
*NONE
Library
. . . . . . . SEPPGM
. . . . . . . . . . .
Printer error message
. . . . . PRTERRMSG
*INQ
More...
Message queue
Library
. . . . . . . . . MSGQ
. . . . . . . . . . .
Activation timer . . . . . . . . ACTTMR
QSYSOPR
*LIBL
170
Image configuration. . . . . . . IMGCFG
*NONE
Maximum pending requests . . . . MAXPNDRQS
6
Print while converting . . . . . PRTCVT
*YES
Print request timer. . . . . . . PRTRQSTMR
*NOMAX
Form definition. . . . . . . . . FORMDF
F1C10110
Library. . . . . . . . . . . .
*LIBL
Remote location: . . . . . . . . RMTLOCNAME
Name or address. . . . . . . .
User-defined options . . . . . . USRDFNOPT
> ‘192.168.5.23’
*NONE
+ for more values
More...
55
56
Section 4: Setting Up - AS/400 (iSeries)
AXIS 5570e/AXIS 5670e User’s Manual
User-defined objects . . . . . . USRDFNOBJ
Object . . . . . . . . . . . .
Library . . . . . . . . . .
Object type. . . . . . . . . .
Data transform program . . . . . USRDTATFM
> AXISPR1
> QGPL
> *PSFCFG
*NONE
Library. . . . . . . . . . . .
User-defined driver program. . . USRDRVPGM
*NONE
Library. . . . . . . . . . . .
Text ‘description’ . . . . . . . TEXT
IPDS over PPR/PPD
More...
AXIS 5570e/AXIS 5670e User’s Manual
Configuring the AXIS
5470e
Section 4: Setting Up - AS/400 (iSeries)
Follow the instructions below to configure your AXIS 5570e/AXIS
5670e using a standard Web browser:
1. Start a Web browser, e.g. Internet Explorer or Netscape
Navigator.
2. Enter the IP address or the host name of the AXIS 5570e/AXIS
5670e in the location field and press the Enter key on your
keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e
will appear.
Note:
To protect the Admin pages and the Configuration Wizard from unauthorized use,
enter a password (default Pass) in the Root Password field under Admin | General
Settings.
57
58
Section 4: Setting Up - AS/400 (iSeries)
AXIS 5570e/AXIS 5670e User’s Manual
Note for IPDS printing:
In the Configuration Wizard, you can choose between PCL or PostScript
printing. Choose the printer language that corresponds to your printer.
3. Click the Configuration Wizard for IBM sessions button.
4. Click the Add Session button. This takes you to the
Configuration Wizard which is a step-by-step guide through the
required configuration settings.
Verifying the
communication
Follow the instructions below to verify the communication by
sending a print job to the AXIS 5570e/AXIS 5670e:
AXISPR1 is an example. Refer to Creating a Printer Device Description, on page 53
for details.
1. Type WRKCFGSTS *DEV AXISPR1 on the AS/400 command line
and press Enter to display the previously created printer device.
The status of the printer device should be VARIED OFF.
2. Vary on the printer device by typing 1 in the Opt field. Press
ENTER.
3. Press F5 to refresh the display. The printer device should now be
VARIED ON.
4. Start the printer writer by typing STRPRTWTR AXISPR1 on the
AS/400 command line. Press Enter.
5. Press F5 to refresh the display. The printer device should now be
ACTIVE/WRITER.
6. Direct a printout to this printer device. A successful printout
verifies the communication link between the AS/400 and the
AXIS 5570e/AXIS 5670e.
The AXIS 5570e/AXIS 5670e is now ready for printing in the AS/400
environment.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Section 5
Setting Up - IBM Mainframe (zSeries)
This section describes how to configure the AXIS 5570e/AXIS 5670e
for printing SCS, 3270 and IPDS data streams using SNA and TCP/IP
transport protocols in the IBM Mainframe (zSeries) environment.
Proceed to the setup section that is relevant to your network
environment, as described in the table below:
Printing
protocol
Data streams
Action
SCS
SNA
3270DS
SNA Printing, on page 60
IPDS
SCS
TN3270E
(TCP/IP)
3270DS
TCP/IP TN3270E Printing, on page 70
IPDS
PPR/PPD
(TCP/IP)
IPDS
PPR/PPD Printing - IPDS data streams, on
page 82
Notes:
•
IPDS is only available for print server models with the IPDS option installed.
Please refer to Product Model Summary, on page 9.
•
SNA is only available for print server models with the SNA option installed.
Please refer to Product Model Summary, on page 9.
59
60
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
If you intend to operate your AXIS 5570e/AXIS 5670e in a multiprotocol environment, you should also proceed to the other relevant
sections in this manual, namely:
Section 4 Setting Up - AS/400 (iSeries)
Section 7 Setting Up - NetWare
Section 6 Setting Up - Windows
Section 8 Setting Up - OS/2
Section 8 Setting Up - Macintosh
Section 9 Setting Up - UNIX
SNA Printing
The AXIS 5570e/AXIS 5670e supports printing of SCS, 3270 and IPDS
data streams via the SNA transport protocol.
Important:
The AXIS 5570e/AXIS 5670e must be set up to emulate an IBM 3174 (3174 CU
mode) in the Mainframe/VTAM environment.
Configuring for SNA printing in 3174 CU Mode is described in three
separate stages:
•
Configuring the IBM Mainframe Host system
•
Configuring the AXIS 5570e/AXIS 5670e
•
Verifying the communication
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Configuring the
Mainframe
Host System
Before you begin
These procedures are compulsory for printing in the IBM Mainframe
environment.
Configuring the host system requires you to do the following:
•
Make sure that a VTAM Logon-mode entry is available for your
AXIS 5570e/AXIS 5670e.
•
Create the VTAM Definition for the Major Node where the Print
Server definition is to be placed.
Make note of the AXIS 5570e/AXIS 5670e serial number that is found
on the backside label of the print server.
Important:
When using a concentrator gateway between the host and your print server, it is
not necessary to define separate VTAM Major Node and PU definitions for the
AXIS 5570e/AXIS 5670e. You will instead be working with the gateway VTAM
definitions. Since the AXIS 5570e/AXIS 5670e will appear to the host as one or
several LU's attached to the gateway PU, you need only add LU definitions to the
gateway major node definition and then proceed to item 3 below.
1. Define a VTAM Major Node Definition where the Print
Server definitions will be placed. Using a channel attached 3174
as a gateway to the host, this definition is typically defined as a
Local Major Node. If you are using a remotely attached
gateway via a 37X5 communications controller or a LAN
attached 3172, you will be working with a Switched Major
Node definition.
61
62
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
2. Add the Print Server PU and LU definitions to the major node
definition.
For Switched Major Node definitions you need to:
•
Add the IDBLK (default = E07) and IDNUM (default = last 5
digits of the AXIS 5570e/AXIS 5670e MAC address) entries to
the PU definition.
•
Code a PATH definition using the unit’s full 12 digit MAC
address.
Example: AnAXIS 5570e/AXIS 5670e with a MAC/node address
of 00408C100086 will be defined as:
PA5570e1
PATH
DIALNO=010400408C100086,
GID=1, FID=1, GRPNM=gggggg
Note:
‘GRPNM’ specifies the symbolic name of a GROUP statement in an NCP major
node. That GROUP statement defines a logical group of SDLC switched lines or
token-ring switched lines.
3. Make sure that the corresponding VTAM Logon-mode entries
are available and that the appropriate LU session types (LU1 or
LU3) are used.
4. Vary ACTive the VTAM Major Node definition for the
AXIS 5570e/AXIS 5670e.
Sample Sessions
The examples below are based on samples given in VTAM
Customization (IBM part no: SC23-0112), with some changes to
optimize use for AXIS 5570e/AXIS 5670e.
VTAM for MVS is assumed, although the configuration for VM and
VSE is similar.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Logon-mode Entry
Creating a VTAM Logon-mode entry for your AXIS 5570e/AXIS 5670e.
Logon-mode entry for LU type 1 printing)
*
* For application output of LU-1 SNA Character Stream (SCS)
*
TITLE ‘SCS5570e’
SCS5570e
MODEENTLOGMODE=SCS5570e,
FMPROF=X’03’,
X
TSPROF=X’03’,
X
PRIPROT=X’B1’,
X
SECPROT=X’B0’,
X
COMPROT=X’3080’,
X
RUSIZES=X’8585’,
X
PSERVIC=X’014000010000000001000000’,
PSNDPAC=X’03’,
X
SRCVPAC=X’03’
X
X
Logon-mode entry for LU type 3 printing
*
* For application output of LU-3 3270 Data Stream (3270DS)
*
TITLE ‘DSC5570e’
DSC5570e
MODEENT LOGMODE=DSC5570e,
FMPROF=X’03’,
X
TSPROF=X’03’,
X
PRIPROT=X’B1’,
X
SECPROT=X’90’,
X
COMPROT=X’3080’,
X
RUSIZES=X’8585’,
X
PSERVIC=X’030000000000185018507F00’,
PSNDPAC=X’03’,
X
SRCVPAC=X’03’
X
X
63
64
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
Switched major
node definitions
The example below shows how the print server PU, PATH, and LU
definitions may be coded in a switched major node definition.
* PU definition
* E07xxxxxx is the node ID set in AXIS 5570e/AXIS 5670e.
*
PU5570e1
PUADDR=04,
X
PUTYPE=2,
X
IDBLK=E07,
X
IDNUM=nnnnn,
X
MAXPATH=1,
X
SSCPFM=USSSCS,
X
USSTAB=USSMAST,
X
VPACING=(0)
*
* Path definition
* xxxxxxxxxxxx is the 12 last digits of the MAC
* address of the AXIS 5570e/AXIS 5670e
*
PA5570e1
PATHDIALNO=0104xxxxxxxxxxxx,
GID=1,
X
PID=1,
X
GRPNM=gggggg
*
* LU definitions. Use either LU5570e1 or LU5570e3
*
* LU type 1 (SCS)
*
LU5570e1
LULOCADDR=2,
X
DLOGMOD=SCS5570e,
X
VPACING=7,
X
PACING=3
*
* LU type 3 (3270DS)
*
LU5570e3
LULOCADDR=2,
X
DLOGMOD=DSC5570e,
X
VPACING=7,
X
PACING=3
X
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Note:
In the PU definition, IDNUM should be set to the five last digits of the AXIS
5570e/AXIS 5670e node address, NODE_ADDR. By default NODE_ADDR stands
for the five last digits of the AXIS 5570e/AXIS 5670e serial number.
In the path definition, PATH DIALNO should be comprised with its first two
digits equal to the place holder, the next two set to the SAP and the remaining
twelve digits set to the AXIS 5570e/AXIS 5670e Ethernet or Node address. By
default the Ethernet/Node address is identical to the AXIS 5570e/AXIS 5670e
serial number. A valid GRPNM must also be supplied.
In the LU definition, the LOCADDR number maps to the Logical Printer number
of the AXIS 5570e/AXIS 5670e. The first eight Local Addresses pass the printout
through Logical Printer 1-8. However, some IBM systems do not allow Local
Address 1 to be used for printing. Refer to Section 13 Using Logical Printers,
on page 170 for more information about logical printers.
Node Definitions
The example below shows how the print server PU and LU definitions
may be coded in a local major node definition:
* 5570e DSPU DEFINITION
DSPU5570e5570e PU CUADDR=E31,
X
MODETAB=MODE3290,
X
PUTYPE=2,ISTATUS=ACTIVE,MAXBFRU=1
DSPULU02 LU
LOCADDR=2
X
SSCPFM=USSSCS,
X
USSTAB=USSTAB,
X
PACING=1,
X
VPACING=2,
X
ISTATUS=ACTIVE,
X
LOGAPPL=MWTC,
X
DLOGMOD=SCS5570e
DSPULU03 LU
LOCADDR=3,
X
SSCPFM=USSSCS,
X
USSTAB=USSTAB,
X
PACING=1,
X
VPACING=2,
X
ISTATUS=ACTIVE,
X
LOGAPPL=MWTC,
X
DLOGMOD=SCS5570e
Note:
65
66
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
If the LAN media at the remote (Print Server) location differs from that at the
host location (e.g. Remote LAN = Ethernet and Host LAN = Token Ring), the MAC
address definitions must be modified, as outlined below:
Print Server Modifications:
The AXIS 5570e/AXIS 5670e Host MAC address (H1_MAC_ADDR) must be bitorder reversed for each byte,
e.g. if the host address is 08005AB77D49 the converted address will be
10005AEDBE92
Host Modifications:
The required Host modifications are dependent upon the VTAM definition for the
Major Node where the Print Server definition is placed.
Case 1:
VTAM Major Node definition is a Switched Major Node.
The MAC address of the AXIS 5570e/AXIS 5670e must be bit-order reversed in
the PATH entry. AnAXIS 5570e/AXIS 5670e with a MAC/node address of
00408C1B06D4 will be defined using the MAC/node address 000231D8602B as
follows:
Case 2:
VTAM Major Node definition is a Local Major Node.
When using a channel attached controller as gateway to the host, the MAC
address of the AXIS 5570e/AXIS 5670e is configured in the gateway. The address
must be reversed, as in case 1 above.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Configuring the
AXIS 5570e/AXIS
5670e
To perform the instructions presented in this section, you should first
assign an IP address to your AXIS 5570e/AXIS 5670e using one of the
methods presented in Setting the IP address, on page 24.
The purpose of the configuration of the AXIS 5570e/AXIS 5670e is to
emulate a LAN attached IBM 3174 Control Unit running SNA PU2.0.
Follow the instructions below to configure the AXIS 5570e/AXIS
5670e using a Web browser:
1. Start a Web browser, e.g. Internet Explorer or Netscape
Navigator.
2. Enter the IP address or the host name of the AXIS 5570e/AXIS
5670e in the location field and press the Enter key on your
keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e
will appear.
Important:
To protect the Admin pages and the Configuration Wizard from unauthorized
use, enter a password (default Pass) in the Root Password field under Admin |
General Settings.
3. Click the Configuration Wizard for IBM sessions button.
67
68
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
4. Click the Add Session button. This will start the Configuration
Wizard which is a step-by-step guide through the required
configuration settings.
Notes for SCS printing:
•
In the Configuration Wizard’s IBM Printer Emulation window, 38xx is the
value used for LaserWriter printers and all other values are used for matrix
printers.
•
In the Configuration Wizard Printer Driver window, PCL is used for LaserWriter printers, all other values apply to matrix printers.
Note for IPDS printing:
In the Configuration Wizard, you can choose between PCL or PostScript
printing. Choose the printer language that corresponds to your printer.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Verifying the
Communication Link
Procedures
The easiest way to test the communication is by sending a print job
to the AXIS 5570e/AXIS 5670e. If there are problems, press the test
button once to print the test page where you can find the present
SNA link status.
1. Power on the Print Server and wait for 2 minutes.
2. Press the test button once to print a test page and make sure
that the SNA status line is defined as either:
•
Idle
•
Actv
•
LU-1
•
LU-3
Note:
Please refer to the Parameter List and FAQ on the Axis Web site, if the status line
indicates that the SNA link is not active.
The AXIS 5570e/AXIS 5670e is now ready for use in the SNA
environment.
69
70
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
TCP/IP TN3270E Printing
The following procedures describe how to configure the AXIS
5570e/AXIS 5670e for SCS, 3270DS and IPDS printing, using TCP/IP
TN3270E.
This is achieved by establishing communication between the AXIS
5570e/AXIS 5670e and Mainframe host via a TN3270E server, using
the TCP/IP transport protocol for the SCS, 3270 and IPDS data
streams, as illustrated below:
AXIS Print server
IPDS is only available for print server models with the IPDS option installed.
Please refer to Product Model Summary, on page 9
Configuring for TN3270E printing is described in four separate stages:
Configuring the
Mainframe host
•
Configuring the IBM Mainframe Host system
•
Configuring the AXIS 5570e/AXIS 5670e
•
Configuring the TN3270E server
•
Verifying the communication
Consult your TN3270E server documentation and make sure that the
appropriate VTAM host system definitions are set up for
mainframe-to-TN3270E server SNA communication.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Configuring the
AXIS 5570e/AXIS
5670e
Follow instructions below to configure the AXIS 5570e/AXIS 5670e
using a Web browser:
1. Start a Web browser, e.g. Internet Explorer or Netscape
Navigator.
2. Enter the IP address or the host name of the AXIS 5570e/AXIS
5670e in the location field and press the Enter key on your
keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e
will appear.
Important:
To protect the Admin pages and the Configuration Wizard from unauthorized use,
enter a password (default Pass) in the Root Password field under Admin | General
Settings.
3. Click the Configuration Wizard for IBM sessions button.
4. Click the Add Session button. This will start the Configuration
Wizard which is a step-by-step guide through the required
configuration settings.
71
72
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
Notes for SCS printing:
•
In the Configuration Wizard, Non-IPDS Printer Emulation uses
value structure 38xx for LaserWriter printers. All other values
can be used for matrix printers.
•
In the Configuration Wizard’s Printer Driver window, PCL is used
for LaserWriter printers, all other values apply to matrix printers.
Note for IPDS printing:
Configuring the
TN3270E server
•
The AXIS 5570e/AXIS 5670e supports eight concurrent TN3270E
host sessions.
•
In the Configuration Wizard, you can choose between PCL or
PostScript printing. Choose the printer language that
corresponds to your printer.
The TN3270E server may be implemented as a software package
running on the mainframe itself, a router or other server hardware.
Configuration examples for two popular TN3270E-capable servers are
described below, namely:
•
Microsoft SNA Server
•
Novell NetWare for SAA.
AXIS Print server
Typical AXIS 5570e/AXIS 5670e TCP/IP TN3270E Network Configuration
Note:
•
Configuration procedures can differ from other TN3270E servers.
•
For additional information about configuring other TN3270E servers, refer
to the Support pages on www.axis.com
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Microsoft SNA Server
Communication is established in two separate stages, SNA Server-toHost connection and SNA Server to AXIS 5570e/AXIS 5670e
connection, as described below:
SNA Server-to-Host Connection
Follow the steps below to set-up a SNA Server-to-Host connection
for the AXIS 5570e/AXIS 5670e:
1. Start Microsoft SNA Server Manager and click the Servers folder.
The Main SNA Server Manager Window is featured in the
illustration below.
2. Insert a new Connection to the host under Connections. Refer to
the online help for assistance on how to configure the
connection.
3. Select the new connection and Insert a 3270 Application LU
(LUA) to this connection.
4. Set the LU Number to the LU Number specified in the host.
5. Set the LU Name to the name you want to use for the printer
device. This is the same name that you specify in the TN3270E
Printer Name parameter of the AXIS 5570e/AXIS 5670e.
73
74
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
6. Click OK.
SNA Server Manager Main Window
SNA Server - AXIS 5570e/AXIS 5670e connection
1. Select the new LUA and drag it to the TN3270 connection
definition (highlighted in the SNA Server Manager Window
above).
2. Select the properties of the LUA.
3. Click the TN3270 tab in the properties popup window.
4. Select Generic Printer Type.
5. Click the IP Address List tab.
6. Specify the IP Address of the client(s) that you want to assign to
this LU. This is the IP address of the AXIS 5570e/AXIS 5670e, i.e.
the same as the INT_ADDR parameter in the Print Server.
7. Click OK.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Verifying the
Communication:
1. Activate the connection you created in step 2 of the above SNA
Server - AXIS 5570e/AXIS 5670e connection procedures. The
status of the connection should be “active”.
2. Make sure the corresponding LU in the host is activated.
3. Activate the TN3270 connection to the AXIS 5570e/AXIS 5670e.
The LUA should change status to SSCP.
4. Check that the printer is connected to the AXIS 5570e/AXIS
5670e.
5. Send a print job from the host.
The AXIS 5570e/AXIS 5670e is now ready for use.
Notes:
•
You can check the status of the TN3270E connection by printing a test page
from the Print Server. This is done by pressing the test button once. Make
sure the TN3270E status (St:) line for your server connection is defined as
either:
•SSCP
•LU-1
•LU-3
•
NetWare for
SAA Server
For additional information about configuring other TN3270E servers, refer
to the Technical Notes on www.axis.com
To set-up a TN3270E connection to the AXIS 5570e/AXIS 5670e you
have to set up PU and LU definitions. This is done by following the
steps below:
1. Start the NWSAA Administrator.
2. Double-click the NWSAA Node. The panel below will appear.
3. Enter the Node ID for the host.
75
76
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
4. Leave the rest at their default settings.
Peer PU profile
5. Click the TN3270 icon. The panel below will appear.
6. Select All Available Host PU profiles.
7. Enter the user name, from the User List, that you want all
TN3270 clients to use.
8. Specify the maximum number of TELNET connections you want
to allow each TN3270 client.
9. Leave the rest at their default settings and click OK.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
PU profile name and Logical adapter
10. Press the “insert” key to create a new Host PU Profile. Choose
Host PU Profile from the list displayed in the dialog. Then the
panel below will appear.
Printer LU
11. Enter a unique name as PU profile name.
12. Enter the number of dependent LUs you want for this PU.
13. Enter the starting LU number.
14. Enter the Node ID (the same ID as for item 3 above).
15. Choose logical adapter.
16. Set maximum frame size to transmit inbound to match the
MAXDATA in the host definition.
17. Enter the host node address.
18. Leave the rest at their default settings.
19. Click the LU Defaults icon. The panel below will appear
20. Set Default LU category to Public.
77
78
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
21. Set Default LU type to Printer (LU type 1 or 3).
22. Specify the VTAM LU name prefix. Click OK.
Notes:
•
When the LUs are created the default names for the Printer Devices will be
<name prefix> followed by a two digit number starting at the number you
entered in the starting dependent LU number field.
•
In the example below, eight LUs are created automatically. The LU names
created will be BRLTST04 through to BRLTST0B. These names must
correspond to the Printer Names you specify for the TN3270E sessions in
the Print Server.
You can now generate a configuration report from NW for SAA. To do
this, simply mark the server icon in the left window and select
Generate Server Configuration Report from the
function menu.
The following table is a summary of a report generated by this
command for the example above.
Profile Name
NWSAA
SNA Network ID:
SEEDB
Peripheral node control point name:
CPNAME
Block ID/PU ID:
05D 66204
Local/Partner SAP for ILUs:
04
Logical Adapter:
E100B_1
PU Profile:
NWSAAPU
Adapter Name
E100B_1
Adapter Type:
LLC 802.2
Terminate peer link if no active APPC sessions:
No
Logical adapter number:
0
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Profile Name
NWSAA
Number of local service access points:
2
Enable adapter at startup:
Yes
PU Profile Name
NWSAAPU
Number of dependent LUs:
8
Starting dependent LU number:
4
Peripheral node control point name:
Node ID (block/PU ID):
NWSAAPU
66204
Offline test mode:
No
Assign only LUs activated by the host:
Yes
Enable SDDLU Support:
No
Adapter Name:
E100B_1
Adapter Type:
802.2
Maximum Session Count:
9
VTAM Name Prefix:
BRLTST
Default LU Type:
1
Default Model Number:
2
Default LU Category:
Public
Maximum frame size to transmit inbound:
Remote node address:
LLC
0521
020066800000
Remote Service Access Point:
Local Service Access Point:
05D
04
04
79
80
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
Profile Name
NWSAA
Yes
Enable PU profile at startup:
Type
Mod
Termination
Method
14
2
TSELF
BRLTST04
1
2
TSELF
Public
BRLTST05
1
2
TSELF
6
Public
BRLTST06
1
2
TSELF
7
Public
BRLTST07
1
2
TSELF
8
Public
BRLTST08
1
2
TSELF
9
Public
BRLTST09
1
2
TSELF
10
Public
BRLTST0A
1
2
TSELF
11
Public
BRLTST0B
1
2
TSELF
LU id
Category
0
Public
4
Public
5
VTAM LU Name
PU Profile Names
NetWare SAA
Maximum connections per client
5
Use IP client name
No
TN3270 NetWare User ID
Admin
Client Response Timer
120
Printer End of Job Timer
9999
Summary of a report generated by Generate Server
Configuration Report (bold text = not default).
Verifying the
Communication:
Follow the steps below to test the communication by sending a print
job to the AXIS 5570e/AXIS 5670e.
1. Make sure the printer is connected to the AXIS 5570e/AXIS
5670e and the corresponding LU in the host is activated.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
2. Send a print job from the host.
The AXIS 5570e/AXIS 5670e is now ready for use. If needed, it can be
further adapted to your system using the Web-based configuration
pages or IBM Printer Emulation. Please refer to Extended IBM Printer
Emulation, on page 251.
You can check the status of the TN3270E connection by printing a test page from
the Print Server. This is done by pressing the test button once. Make sure the
TN3270E status (St:) line for your server connection is defined as either:
•
SSCP
•
LU-1
•
LU-3
For additional information about configuring other TN3270E servers, refer to the
Technical Notes on www.axis.com
81
82
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
PPR/PPD Printing - IPDS data streams
Important:
IPDS is only available for print server models with the IPDS option installed.
Please refer to Product Model Summary, on page 9.
Before you begin
Configuration
Procedures
In order to use the AXIS 5570e/AXIS 5670e to print IPDS data using
TCP/IP as the transport protocol, the following software must be
installed and configured on your MVS:
•
PSF/MVS Version 2 release 2.0 with APAR OW15599.
•
MVS Scheduler APAR OW12236 to support the two new PRINTDEV keywords: IPADDR and PORTNO.
•
TCP/IP version 3 release 1, or higher
The configuration procedures presented in this section are divided
into seven separate steps:
1. Specifying the TCP/IP address space name
2. Defining the MVS control unit
3. Modifying the TCP/IP profile on your MVS system, if necessary
4. Configuring the AXIS 5570e/AXIS 5670e
5. Verifying the communication between the AXIS 5570e/AXIS
5670e and the IBM Mainframe
6. Defining the AXIS 5570e/AXIS 5670e as a writer-controlled
printer to JES
7. Defining the printer to PSF with a PRINTDEV statement,
including the IP address and port number.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Specifying the TCP/IP
address space name
To specify a TCP/IP address space name you should enter the
following EXEC statement in the appropriate PSF writer procedure:
//STEP01 EXEC
PGM=APSPPIEP,REGION=4096K,PARM=(,,,,tcpip_name)
where tcpip_name is the name of the TCP/IP address space. If this
parameter is not coded, PSF uses the default name TCPIP. For a full
description of the PARM parameter refer to IBM’s user documentation
covering the print service facility.
Defining the
MVS control unit
If you have not already done so, you must define the communications
control unit, e.g. the 3172 control unit or the 3745 control unit, to
MVS. The tool to use is dependent on your MVS version:
•
When using a version earlier than MVS 4.1.0, you should use an
MVS Configuration Program (MVSCP).
•
When using a version of MVS 4.1.0 or higher, you can use a
HardWare Configuration Definition (HCD) or an MVSCP.
For more information about using these methods, please refer to one
of the following publications:
•
MVS/ESA Planning: Dynamic I/O Configuration
•
OS/390 HCD Planning
•
HCD User's Guide
83
84
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
Modifying the
TCP/IP profile
The TCP/IP profile contains system configuration statements used to
initialize the TCP/IP address space. Among those statements, the
following are subject to special considerations when you are printing
from PSF on TCP/IP-attached printers:
•
DATABUFFERPOOLSIZE
•
SMALLDATABUFFERPOOLSIZE
•
TINYDATABUFFERPOOLSIZE
•
KEEPALIVEOPTIONS
•
GATEWAY
Below is an excerpt from an example TCP/IP Profile (not a complete
profile) . Examples of the statements above are printed in bold:
ACBPOOLSIZE
1000
ADDRESSTRANSLATIONPOOLSIZE
1500
CCBPOOLSIZE
150
DATABUFFERPOOLSIZE
160
ENVELOPEPOOLSIZE
32768
750
IPROUTEPOOLSIZE
300
LARGEENVELOPEPOOLSIZE
50
RCBPOOLSIZE
50
SCBPOOLSIZE
256
SKCBPOOLSIZE
256
SMALLDATABUFFERPOOLSIZE
256
TCBPOOLSIZE
512
TINYDATABUFFERPOOLSIZE
256
UCBPOOLSIZE
100
KEEPALIVEOPTIONS
INTERVAL
10 SENDGARBAGE
FALSE
ENDKEEPALIVEOPTIONS
GATEWAY
; * Network
10
First Hop
=
Linkname
BCPLAN
DEFAULTNET 10.10.12.1 BPCLAN
Packet Size Subnet mask
2000
2000
Subnet value
255.255.255.0 10.10.12.0
255.255.255.0 0
Note:
If you change any of the values in the TCP/IP profile, you must restart TCP/IP to
activate the new settings.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
The table below provides more information about the statements.
Statement
Explanation
DATABUFFERPOOLSIZE
Defines the number and size of the data buffers. It is recommended that you specify at least 160
data buffers and a buffer size of 32768 bytes
SMALLDATABUFFERPOOLSIZE
Defines the number of small data buffers. It is recommended that you specify at least 256 small
data buffers
TINYDATABUFFERPOOLSIZE
Defines the number of tiny data buffers. It is recommended that you specify at least 256 tiny
data buffers
KEEPALIVEOPTIONS
PSF relies on TCP to detect when a connection with a TCP/IP-attached printer or an AXIS
5570e/AXIS 5670e is no longer available. When no data has been exchanged between PSF and its
connection partner, TCP sends keep-alive probes to the connection partner periodically. These
periodic probes, called keep-alive transmissions, enable TCP to discover when a connection is no
longer usable even if the connection partner is abruptly powered off or is no longer accessible
through the network.
The frequency of keep-alive transmissions is controlled by the INTERVAL parameter on the
KEEPALIVEOPTIONS statement. The frequency applies to all TCP applications that direct TCP to
send keep alive transmissions. The default frequency is after about two hours of inactivity.
We recommend that you specify a shorter interval than the default, such as 10 minutes, for the
interval between keep-alive transmissions.
Also, if any target host on you network requires that the keep-alive packet contains data, specify
SENDGARBAGE TRUE
GATEWAY
The Packet_size parameter of the GATEWAY statement defines the maximum transmission unit
(MTU) for the MVS host. The MTU size must not exceed the maximum size that can be sent
through the control unit; if it does, transmission problems will occur.
The MTU size should be 2000 bytes and the MTU size for the MVS host should be the same as the
MTU size for the printer.
For values in the GATEWAY statement other than the packet size, specify the values that are
correct for your installation.
For more information about the TCP/IP profile and the statements
described in this section, please refer to:
•
IBM TCP/IP MVS Customization and Administration Guide
•
IBM TCP/IP Performance and Tuning Guide
85
86
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
Configuring the
AXIS 5570e/AXIS
5670e
Follow the instructions below to configure your AXIS 5570e/AXIS
5670e using a standard Web browser:
1. Start a Web browser, e.g. Internet Explorer or Netscape
Navigator.
2. Enter the IP address or the host name of the AXIS 5570e/AXIS
5670e in the location field and press the Enter key on your
keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e
will appear.
Note:
To protect the Admin pages and the Configuration Wizard from unauthorized
use, enter a password (default Pass) in the Root Password field under Admin |
General Settings.
Note for IPDS printing:
In the Configuration Wizard, you can choose between PCL or PostScript printing.
Choose the printer language that corresponds to your printer.
3. Click the Configuration Wizard for IBM sessions button.
4. Click the Add Session button. This will start the Configuration
Wizard which is a step-by-step guide through the required IBM
configuration settings.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Verifying the
communication
You can verify the communication between the MVS system and the
AXIS 5570e/AXIS 5670e by pinging the print server from the MVS
system. A successful ping indicates that the MVS system can
communicate with the AXIS 5570e/AXIS 5670e.
From an TSO session, enter the following command:
TSO PING <IP_address>
Note:
The IP address is the IP address of the AXIS 5570e/AXIS 5670e.
In JES2, enter the following command from the System Display and
Search Facility (SDSF) menu 6:
ping <IP_address>
Note:
The IP address is the IP address of the AXIS 5570e/AXIS 5670e.
Here is an example of a successful ping:
EZA0458I Ping V3R1:
Pinging host 10.50.45.200
(Use ATTN to interrupt.)
EZA0463I PING: Ping #1 response took 0.055 seconds
Successes so far = 1
And here is an example of an unsuccessful ping:
EZA0458I Ping V3R1:
Pinging host 10.50.45.200
(Use ATTN to interrupt.)
EZA0464I PING: Ping #1 timed out
If the ping is not successful make sure the AXIS 5570e/AXIS 5670e is
configured according to the instructions in Setting the IP address,
on page 24 and in Configuring the AXIS 5570e/AXIS 5670e, on
page 71. If these items are all in order, consult your TCP/IP network
administrator.
87
88
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
JES definitions
When a TCP-attached printer is to be used with JES, it must be
defined for deferred-printing mode. To use a PSF printer for deferred
printing under JES, you must first code JES initialization statements
to define FSSs and FSAs for PSF printers. For JES2, the FSS is defined
by an FSS statement, and the FSA is defined by a PRTnnnn statement.
For JES3, the FSS is defined by an FSSDEF statement, and the FSA is
defined by a DEVICE statement.
The maximum number of FSSs and FSAs that are supported are:
•
FSSs = 2000
•
FSAs per FSS = 64
The actual number of FSAs per FSS depends on several factors like:
JES2 Initialization
•
The virtual region size below the 16-megabyte line
•
The number and the size of form definitions and page definitions
•
The number of buffers specified (BUFNO) for channel-attached
printers
•
The block sizes of the font, page segment, overlay, form definition, and page definition libraries
The example below shows a sample JES2 statements for a TCP/IPattached AXIS 5570e/AXIS 5670e:
FSS (FSS1) PROC=SAMPPROC,HASPFSSM=HASPFSSM
PRT1
FSS=FSS1,MODE=FSS,PRMODE=(LINE,PAGE,),
CLASS=C,UCS=0,SEP=NO,SEPDS=NO,CKPTPAGE=100
START=YES,MARK=NO,TRKCELL=YES
Note:
This is only an example. For specific coding for JES parameters, refer to the JES
publication for the level of JES you are using.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
The following paragraphs describe the JES2 initialization statements
shown above, which are typical of the JES2 statements used with
PSF. For more detailed descriptions of all JES2 initialization
statements, refer to the JES2 initialization and tuning publication for
your operating system.
FSS Statement:
The FSS initialization statement is optional but recommended. If it is
omitted, JES2 generates a default FSS for that device. The FSS
initialization statement defines an FSS to JES2. The FSS statement is
associated with one or more PRTnnnn statements that define each
printer FSA. For a description of all FSS parameters, refer to the JES2
initialization and tuning publication for your operating system. The
FSS statement contains the following parameters for PSF:
FSS Statement
Explanation
FSS (fasname)
Specifies the unique 1- to 8-character name of a particular FSS. This name is referenced in the PRTnnnn
statement for each printer FSA that is associated with this FSS. When you start the first printer that has an FSA
definition for that FSS, an FSS address space is created for PSF. PSF manages this FSS and the printer FSA for
the first printer. If you start a second printer with an FSA definition for the same FSS, PSF manages a separate
FSA for the second printer in that FSS.
PROC
Specifies a procedure for starting the PSF FSS. The procedure, which must be defined before that FSS is started,
is a member of either SYS1.PROCLIB or a library concatenated to SYS1.PROCLIB.
HASPFSSM
Specifies the 1- to 8-character name of the load module that is loaded into the PSF FSS address space. This
load module contains the various FSI service routines that JES2 supplies. For PSF, specify the default value
(HASPFSSM=HASPFSSM).
PRTnnnn Statement:
A PRTnnnn statement, which is required to define each printer nnnn
statement FSA, is associated with an FSS statement. Each printer
FSA should have a unique PRTnnnn name that must match the label
on the CNTL, ENDCNTL, and PRINTDEV statements for the PSF startup
procedure specified in the PROC parameter.
Note:
The label on the PRINTDEV statement must be 8 characters or fewer. PSF
accepts the PRTnnnn, PRINTnn, and PRINTERn formats. PRTnnnn is the
recommended format.
89
90
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
The PRTnnnn parameters create JES2 default values that are used
unless other values are specified in the application program JCL. The
PRTnnnn statement contains the following parameters:
PRTnnnn Statement
Explanation
CKPTPAGE
Specifies the number of pages between data-set checkpoints. If checkpoint intervals are too frequent, printer
performance is significantly reduced. If intervals are too infrequent, and a PSF error occurs, the job has to be
reprocessed from the last checkpoint. In this case, printer performance is significantly reduced if PSF errors
continue to occur. The recommended starting value is 100.
CLASS
Specifies the output classes processed by the printer. By defining print classes you can handle disabled
mechanisms.
FSS
Specifies the FSS for this device and must match the FSA name specified in the corresponding FSS statement.
This parameter is required.
MARK
Enables form markings to be placed on the job trailer pages. For the AXIS 5570e/AXIS 5670e you should set
this parameter to NO.
Note: This parameter is new in JES2 and replaces the MARK | NOMARK parameter.
MODE
Specifies that the printer is managed by an FSS. This parameter is required.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
PRTnnnn Statement
Explanation
PRMODE
Specifies the data-set processing modes supported for the printer. It lists all the PRMODE values that the
printer accepts. If the AXIS 5570e/AXIS 5670e is connected to a PostScript printer, the correct setting is
PRMODE=(PAGE,LINE,).. This setting indicates that composed-page and line data sets can be
printed.
Enables job-header and job-trailer separator pages to be produced.
Note1: If the Distributed Print Function (DPF) of PSF/2 is installed, you may need to set
this parameter to YES.
SEP
Note2: This parameter is new in JES2 and replaces the SEP | NOSEP parameter.
SEPDS
Enables formatted data-set header separator pages to be produced.
Note: This parameter is new in JES2 and replaces the SEPDS | NOSEPDS parameter.
START
Specifies the way that the printer is started. The parameter value NO specifies that the printer is to be started
by an operator command. The parameter value YES specifies that the printer, if it is ready, is to start
automatically when JES2 starts processing.
Note: This parameter is new in JES2 and replaces the DRAIN | START parameter.
TRKCELL
Specifies whether track-cell despooling is to be used or not. It is recommended to set this parameter to
UCS
Specifies a default font. If you want to select a font in the startup procedure instead of the JES2 default font,
you should set this parameter to 0.
JES3 Initialization
YES.
Below is sample JES3 statements for an TCP/IP attached AXIS
5570e/AXIS 5670e. In the example the JNAME=PRT1 has been used.
FSSDEF,TYPE=WTR,FSSNAME=FSS3,PNAME=SAMPPRO3,SYSTEM=SYS1,TERM=NO
DEVICE,DTYPE=PRTAFP1,JNAME=PRT1,JUNIT=(,SYS1,,ON),FSSNAME=FSS3
MODE=FSS,PM=(LINE,PAGE,),CHARS=(YES,GT12),
CARRIAGE=(TES,A868),CKPNTPG=100,HEADER=YES,WC=(C)
Note:
This is only an example. For specific coding for JES parameters, refer to the JES
publication for the level of JES you are using.
91
92
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
The following paragraphs describe the JES3 initialization statements
shown above, which are typical of the JES3 statements used with
PSF. For more detailed descriptions of all JES3 initialization
statements, refer to the JES3 initialization and tuning publication for
your operating system.
FSSDEF Statement:
The FSSDEF initialization statement is optional but recommended. If
it is omitted, JES3 generates a default FSS for the printer being
invoked.
The FSSDEF statement can contain the following parameters:
FSSDEF Statement
Explanation
TYPE
Specifies that the FSS is an output writer for deferred printing. This parameter is required.
FSSNAME
Specifies the unique name of a particular FSS. This parameter is required.
PNAME
Specifies a procedure for starting a specific PSF FSS. The procedure, which must be defined before the FSS is
started, is a member of the procedure library defined by the STCPROC parameter of the STANDARDS
statement or of the IATPLBST procedure library. Different FSSDEF initialization statements can refer to the same
startup procedure.
The PNAME parameter specifies either a startup procedure supplied with PSF, or one of your organization’s
procedures.
SYSTEM
Specifies the JES3 processor on which the FSS is run. The name must match the
MAINPROC statement for the processor.
TERM
Specifies the way that the FSS is terminated. The parameter value YES indicates that the FSS is terminated if
the JES3 global address space is terminated by a *RETURN or *DUMP operator command.
NAME parameter in the
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
DEVICE Statement:
A DEVICE statement is required for each printer. The DEVICE
parameters create JES3 default values that are used unless other
values are specified in the JCL application program. The DEVICE
statement can contain the following parameters:
Device Statement
Explanation
Specifies the JES default page definition.
The value YES specifies that the page definition can be changed during startup
procedures.
CARRIAGE
The value NO specifies that the page definition cannot be changed during startup
procedures.
The value aaaa specifies that the un-prefixed name, 1 to 4 characters long, of the page
definition is to be used as default. The name specified here, or the JES3 system default, is
the PSF default page definition.
CHARS
Specifies a default JES3 font.
CKPNTPG
Specifies the number of pages between data-set checkpoints. If checkpoint intervals are too frequent, printer
performance is significantly reduced. If intervals are too infrequent, and a PSF error occurs, the job has to be
reprocessed from the last checkpoint. In this case, printer performance is significantly reduced if PSF errors
continue to occur. The recommended starting value is 100.
DTYPE
Identifies the printer device type. For the AXIS 5570e/AXIS 5670e you should specify the parameter value
PRTAFP1. This parameter is required.
FSSNAME
Specifies a unique FSS for this printer DEVICE statement. The value must match the value coded for the
FSSNAME parameter in the corresponding FSSDEF statement.
HEADER
Specifies if job and data set header pages are printed. If DPF is installed, you may need to specify HEADER=YES.
JNAME
Specifies the name of the printer FSA. Each printer FSA should have a unique JNAME. This unique JNAME is 8
characters or fewer and must correspond to its label on the CNTL, ENDCNTL, and PRINTDEV
statements for the PSF startup procedure specified in the PNAME parameter. This parameter is required.
93
94
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
Device Statement
Explanation
JUNIT
Specifies:
1. The device address (host-connected, channel-attached, non-SNA printers only). Do not specify a device
address for the AXIS 5570e/AXIS 5670e when using TCP/IP attachment.
2. The name of the processor to which the device is attached
3. A destination class for messages about the device
4 .Whether the device is initially online or offline
This parameter is required.
MODE
Specifies that the printer is managed by an FSS. This parameter is required.
PM
Specifies which data-set processing mode is supported. For the AXIS 5570e/AXIS 5670e attached to Postscript
printers, the correct setting is PRMODE=(LINE,PAGE,), indicating that composed-page and line
data sets can be printed.
WC
Specifies the print output class that the printer is to process. You may want to consider handling disabled
mechanisms by defining print classes.
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Defining the
printer to PSF
Each AXIS 5570e/AXIS 5670e must be defined to PSF with a
PRINTDEV statement in the PSF startup procedure. The following
keywords are required on the PRINTDEV statement:
•
IPADDR='xxx.xxx.xxx.xxx'
•
PORTNO='xxxx'
The IPADDR parameter specifies the IP address of the AXIS
5570e/AXIS 5670e in dotted-decimal notation.
Note:
Do not specify a host name in place of the dotted-decimal address.
The PORTNO keyword specifies the TCP/IP port to use for the print
session. This port number must match the port number set up for the
AXIS 5570e/AXIS 5670e in Configuring the AXIS 5570e/AXIS
5670e, on page 71.
Below is a sample procedure, APSWPROT, which you can modify to suit
your installation. The PRINTDEV statement includes the required
IPADDR and PORTNO keywords. In the PRINTDEV example below, the
TCP/IP port number 5100 is used, but any port, larger that 1024, can
be used as long as the same port is set up in the AXIS 5570e/AXIS
5670e.
The APSWPROT procedure contains JCL parameters to produce a
startup procedure for either 240-pel and 300-pel printers, but the
references to 300-pel resolution are commented out. To create
separate startup procedures, make two copies of APSWPROT, and then
follow the commented instructions in APSWPROT. Keep one
unchanged copy as your startup procedure for a resolution of 120 or
240 pels. In the second copy, delete or comment out all references to
240-pel resolution, and make all references to 300-pel resolution
active. This changed copy is your startup procedure for 300-pel
resolution.
95
96
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
If you want to print both 240-pel and 300-pel AFP/IPDS jobs, create
two separate FSAs, one for jobs with resolution of 120 or 240, and
one for jobs with resolution of 300 pels. The 240-pel resolution FSA
uses 240-pel resources, and the 300-pel resolution FSA uses 300-pel
resources. Both FSAs are defined to drive the same printer; however,
only one FSA can be active at one time for a given printer. You should
define separate classes or destinations for each FSA. Your
installation must route the appropriate jobs to the appropriate class
or destination. The two FSAs can be defined in the same or in
separate startup procedures.
//APSWPROT PROC
//********************* THE PSF TCP/IP WRITER PROCEDURE **********************
//*
//*01* MODULE-NAME = APSWPROT
//* $MOD(APSWPROT) COMP(APS) PROD(PSF) : RELEASE 2.2.0
//*
//*01* DESCRIPTIVE-NAME = START PROCEDURE FOR PSF:
//*
//*
TCP/IP ATTACHED DEVICES
//*
//*01* STATUS = VERSION 2, RELEASE 2, LEVEL 0
//*
//*01* FUNCTION = THIS PROCEDURE IS COPIED FROM THE
//*
DISTRIBUTION LIBRARY TO SYS1.PROCLIB.
//*
THIS COPY IS PERFORMED BY MACRO ‘SGAPS5PR’.
//*
//*01* NOTES = THE FULL NAME OF THE DEFAULT PAGEDEF IS
//*
//*
//*
//*
//*
//*
//*
//*
//*
//*
P1A06462.
THE FULL NAME OF THE DEFAULT FORMDEF IS
F1A10110.
THE FULL NAMES OF THE DEFAULT FONTS ARE
X0GF10, X0GS10, X0TU10, AND X0GU10
THE FULL NAME OF THE SEPARATOR PAGE PAGEDEF IS
P1V06483
THE FULL NAME OF THE SEPARATOR PAGE FONT IS
X0GT15
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Example continues
CONT...
//* REQUIRED ACTIONS =
//*
RESOLUTION - THIS START PROCEDURE IS SET UP FOR DRIVING
//*
A TCP/IP DEVICE AT 240 PEL RESOLUTION. TO CHANGE IT
//*
TO DRIVE 300 PEL RESOLUTION TCP/IP ATTACHED DEVICES:
//*
//*
//*
A) COMMENT OUT THE FIRST PRINTDEV STATEMENT AND UNCOMMENT
THE SECOND PRINTDEV STATEMENT
//*
//*
B) THE FONT02 DATA SET MUST CONTAIN THE CONVERTED
//*
DEFAULT FONTS LISTED IN THE PRINTDEV.
//*
THE FONTS ARE CONVERTED USING THE FONT
//*
CONVERSION UTILITY APSRCF30. SEE THE PSF
//*
SYSTEM PROGRAMMING GUIDE.
//*
//*01* CHANGE-ACTIVITY :
//* $H1=LAPS0001, HAF1103, 080195 DKU1JAU : TCP/IP SUPPORT
//*
//**** END OF SPECIFICATIONS ***/
//STEP01
EXEC PGM=APSPPIEP,REGION=4096K
//JOBHDR OUTPUT PAGEDEF=V06483,
/* JOB SEPARATOR PAGEDEF
//
/* JOB SEPARATOR FORMDEF
*/
/* JOB SEPARATOR PAGEDEF
*/
FORMDEF=A10110,CHARS=GT15
//JOBTLR OUTPUT PAGEDEF=V06483,
*/
//
FORMDEF=A10110,CHARS=GT15
/* JOB SEPARATOR FORMDEF
*/
//DSHDR
OUTPUT PAGEDEF=V06483,
/* DS
SEPARATOR PAGEDEF
*/
//
FORMDEF=A10110,CHARS=GT15
/* DS
SEPARATOR FORMDEF
//MSGDS
OUTPUT PAGEDEF=V06462,
/* MESSAGE DATASET PAGEDEF
//
FORMDEF=A10110
//FONT01
DD
DSN=SYS1.FONTLIBB,
//
DISP=SHR
//FONT02
DD
//
DISP=SHR
//PSEG01
DD
//
DISP=SHR
//OLAY01
DD
//
DISP=SHR
//PDEF01
DD
//
DISP=SHR
//FDEF01
DD
//
DISP=SHR
DSN=SYS1.FONT300,
DSN=SYS1.PSEGLIB,
DSN=SYS1.OVERLIB,
DSN=SYS1.PDEFLIB,
DSN=SYS1.FDEFLIB,
*/
*/
/* MESSAGE DATASET FORMDEF
*/
/* SYSTEM FONTS - 240 PEL
*/
/* SYSTEM FONTS - 300 PEL
*/
/* SYSTEM PAGE SEGMENTS
*/
/* SYSTEM MEDIUM OVERLAYS
*/
/* SYSTEM PAGEDEFS
*/
/* SYSTEM FORMDEFS
*/
97
98
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
Example continues
CONT...
//* ************************************************************
//*
//* ************************************************************
//PRT1
CNTL
//PRT1
PRINTDEV FONTDD=*.FONT01, /* 240 PEL FONT LIBRARY DD
//*
/* <-- SEE REQUIRED ACTIONS
//*
/* ABOVE
//*PRT1
*/
PRINTDEV
PRINTDEV FONRDD=*.FONT02, /* 300 PEL FONT LIBRARY DD
*/
*/
*/
*/
*/
//*
/* <-- SEE REQUIRED ACTIONS
*/
//*
/* ABOVE
*/
//
OVLYDD=*.OLAY01,
/* OVERLAY LIBRARY DD
*/
//
PSEGDD=*.PSEG01,
/* SEGMENT LIBRARY DD
*/
//
PDEFDD=*.PDEF01,
/* PAGEDEF LIBRARY DD
*/
//
FDEFDD=*.FDEF01,
/* FORMDEF LIBRARY DD
*/
//
JOBHDR=*.JOBHDR,
/* JOB HEADER SEPARATOR
*/
/* OUTPUT
*/
//*
//
JOBTRLR=*.JOBTLR,
//*
//
DSHDR=*.DSHDR,
//*
/* JOB TRAILER SEPARATOR
*/
/* OUTPUT
*/
/* DATA SET HEADER
*/
/* SEPARATOR
*/
*/
//
MESSAGE=*.MSGDS,
/* MESSAGE DATA SET OUTPUT
//
BUFNO=5,
/* NUMBER OF WRITE DATA BUFFERS*/
//
PAGEDEF=A06462,
/* DEVICE PAGEDEF DEFAULT
//
FORMDEF=A10110,
/* DEVICE FORMDEF DEFAULT
*/
//
CHARS=(GF10,
/* DEVICE
*/
//
GS10,TU10,GU10),
/* DEFAULT FONT SET
*/
//
PIMSG=YES,
/* ACCUMULATE DATA SET
*/
/* MESSAGES
*/
/* REPORT ALL DATA-CHECK
*/
//*
//
DATACK=BLOCK,
//*
//
TRACE=NO,
//
FAILURE=WCONNECT,
//*
*/
/* ERRORS
*/
/* CREATE INTERNAL TRACE
*/
/* PSF ACTION ON PRINTER
*/
/* FAILURE
*/
//
TIMEOUT=REDRIVE,
/* PSF ACTION ON TIMEOUT
*/
//
MGMTMODE=IMMED,
/* PRINTER MANAGEMENT MODE
*/
//
DISCINTV=40,
/* DISCONNECT INTERVAL IN
*/
/* SECONDS
*/
//*
//
ADDRESS
IPADDR=’xxx.xxx.xxx.xxx’
*/
/* AXIS 5570e/AXIS 5670e IP
//
PORTNO=’5100’,
/* TCP/IP PORTO
//PRT1
ENDCNTL
*/
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries)
Although it is not recommended, it is possible to drive the printer
with just one FSA, if one of the following conditions are met:
•
All the resources in the resource libraries are resolution-independent, and all the jobs that use inline resources or user libraries
contain resources that are resolution-independent.
•
All jobs that request a resolution that is different from the resolution-dependent resources in the PSF system and security libraries contain the resources at the requested resolution, either as
inline resources or in the user's library.
Even if a PSF user requests 120-pel resolution for an AFP print job
being sent to the printer, PSF requires 240-pel resources from the
library. Do not store 120-pel resources in the library.
Starting and stopping
the PSF/MVS printer
Starting the printer
When operating the AXIS 5570e/AXIS 5670e when emulating a
TCP/IP attached IPDS printer, you should use JES operator commands,
just as if the printer were channel-attached or SNA-attached.
To start a TCP/IP-attached printer, do the following:
1. Start TCP/IP.
2. Power on the printer(s).
3. Power on the AXIS 5570e/AXIS 5670e.
4. Start the printer FSA as indicated below.
Before starting a PSF FSS, you must have a cataloged startup
procedure in SYS1.PROCLIB or any other system procedure library.
This procedure specifies PSF initialization parameters and libraries
that contain system and installation resources. The name of this
procedure can be specified in the FSSDEF statement of the JES
initialization deck. If the name is omitted, JES3 supplies a default
name, that is chosen for the defined printer.
99
100
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual
When you install PSF, you must create or update the required
libraries referenced by the startup procedure, and you should consider
any need to increase the region size, as specified in the EXEC
statement, to accommodate resources and an increased number of
printer FSAs. The startup procedure can also specify defaults that
cannot be set with JES initialization statements for printer FSA
definitions.
Stopping the printer
You can stop a TCP/IP-attached printer in several ways but this is the
recommended method:
Stop the PSF FSA for the printer by entering the following command
from the MVS console.
JES2:
$Pprinter-name
JES3:
*VARY printer-name, OFF
*CANCEL printer-name
The variable printer-name specifies the name of the printer FSA as defined
in JES definitions, on page 88.
You can now disconnect the power supply from the AXIS 5570e/AXIS
5670e.
AXIS 5570e/AXIS 5670e User’s Manual
Section 6
Section 6: Setting Up - Windows
Setting Up - Windows
Having connected the AXIS 5570e/AXIS 5670e to your network, as
described in Connecting a printer to the Ethernet Network, on page
20, this section describes how to install the AXIS 5570e/AXIS 5670e
in the Windows environment. Identify your Windows platform and
follow the installing instructions from the list below.Overview of
installation methods
Refer to the table below to determine the most appropriate
installation method according to your computer environment:
Windows Platform
Printing Protocol
Method
See...
Standard Windows
Add Printer Wizard
Adding Printers in Windows 2000/
Windows XP over TCP/IP (LPR), on
page 102
Microsoft
LPR Monitor
Adding Printers in Windows
2000/Windows XP using the Microsoft LPR Monitor, on page 109
Windows 2000
Windows XP
TCP/IP (LPR)
Windows 2000
NetBIOS/NetBEUI
AXIS Print Monitor software
Adding Printers in Windows NT 4
Using the Microsoft LPR Monitor,
on page 112
TCP/IP (LPR)
AXIS Print Monitor software
Adding Printers over TCP/IP in
Windows NT 4 using AXIS Print
Monitor, on page 115
NetBIOS/NetBEUI
AXIS Print Monitor software
Adding NetBIOS/NetBEUI Printers
in Windows 2000 using AXIS Print
Monitor, on page 116
Windows NT
TCP/IP (LPR)
AXIS Print Monitor software
Windows 98
Windows Me
NetBIOS/NetBEUI
Adding Printers in Windows 98
and Me over TCP/IP using AXIS
Print Monitor, on page 119
Adding Printers in Windows 98
and Me over NetBIOS/NetBEUI using AXIS Print Monitor, on page
121
101
102
Section 6: Setting Up - Windows
AXIS 5570e/AXIS 5670e User’s Manual
If you intend to use the AXIS 5570e/AXIS 5670e in a multiprotocol
environment, you should also refer to the following sections:
Section 7
Section 8
Section 8
Section 9
Setting Up - NetWare, on page 123
Setting Up - OS/2, on page 117
Setting Up - Macintosh, on page 158
Setting Up - UNIX, on page 165
Adding Printers in Windows 2000/ Windows XP over TCP/IP (LPR)
Follow the instructions below to use the standard Windows method
for adding a network printer in Windows 2000/ Windows XP
(Windows XP Professional is described in this example).
Windows XP:
1. Go to Start | Printers and Faxes and click the Add a Printer icon
to start the Add Printer Wizard. Click Next.
(Windows XP Home Edition: Choose Start | Control Panel |
Printers and Faxes | Add a Printer to start the Windows Add
Printer Wizard)
Windows 2000:
1. Go to Start | Settings | Printers and click the Add Printer icon
to start the Add Printer Wizard. Click Next.
AXIS 5570e/AXIS 5670e User’s Manual
Section 6: Setting Up - Windows
2. Select Local Printer attached to this computer.
Make sure the Automatically detect and install my Plug and
Play printer check box is not checked. Click Next.
3. Click the Create a new port radio button and select Standard
TCP/IP Port from the list. Click Next and the Add Standard
TCP/IP Printer Port Wizard starts. Click Next.
103
104
Section 6: Setting Up - Windows
AXIS 5570e/AXIS 5670e User’s Manual
4. Enter the IP address of the print server (Example: 192.168.3.191)
The Port Name field will be filled in automatically when you enter
the IP address.
Add the port you want to use as a suffix (optional):
5570e:
Physical Port
Add suffix
Entry example
USB port
Type _USB1
192.168.3.191_USB1
LPT1 (parallel port)
Type _LPT1
192.168.3.191_LPT1
Physical Port
Add suffix
Entry example
LPT1 (parallel port)
Type _LPT1
192.168.3.191_LPT1
LPT2 (parallel port)
Type _LPT2
192.168.3.191_LPT2
COM1 (serial port)
Type _COM1
192.168.3.191_COM1
5670e:
Click Next.
AXIS 5570e/AXIS 5670e User’s Manual
Section 6: Setting Up - Windows
5. In the Additional Port Information Required window, enter the
Device Port you want to use, you will see LPT1, LPT2 and COM1 in
a drop-down menu:
5570e:
Physical print server port connected to printer
Choose port
USB port
LPT2
LPT1 (parallel port)
LPT1
5670e:
Physical print server port connected to printer
Choose port
LPT1 (parallel port)
LPT1
LPT2 (parallel port)
LPT2
COM1 (serial port)
COM1
Click Next.
105
106
Section 6: Setting Up - Windows
AXIS 5570e/AXIS 5670e User’s Manual
Click Next and Finish
6. Select Manufacturer and Printer from the driver list. Click Next.
AXIS 5570e/AXIS 5670e User’s Manual
Section 6: Setting Up - Windows
7. Choose whether you want to keep the existing driver or to
replace it. If you already have the printer’s driver installed, you
will be asked whether to keep it or to replace it.
8. Click Next. Supply a name for the printer and choose whether
you want to make it your default printer. Click Next.
107
108
Section 6: Setting Up - Windows
AXIS 5570e/AXIS 5670e User’s Manual
9. Choose whether you want to share the printer with other
network users, print a test page, etc. Select the appropriate radio
button and click Next and Finish.
10. Print a test page to verify your installation.
You have now completed the installation.
¨
Check www.axis.com/techsup for updates on the ‘tcpmon.ini’ file!
AXIS 5570e/AXIS 5670e User’s Manual
Section 6: Setting Up - Windows
Adding Printers in Windows 2000/Windows XP using the Microsoft LPR Monitor
This section describes how to set up a Windows 2000/XP server for
LPR printing over the TCP/IP protocol, using the built-in Microsoft
LPR Monitor i.e. Print Services for UNIX.
Note:
See Alternative Method for LPR Printing, on page 111 for
instructions on how to set up printing over LPR without
installing Print Services for Unix.
Basic Setup
Preparing for
LPR Printing
If you have not already done so, you should perform the TCP/IP basic
setup procedures prior to installing a printer for LPR printing.
Follow the following steps to prepare for LPR printing:
1. Open the Control Panel.
2. Click Add/Remove Programs.
3. Click Add/Remove Windows Components.
4. Check Other Network File and Print Services and click Details.
5. Check Print Services for Unix and click OK.
6. Click Next and Finish.
7. Close Add/Remove Programs and the Control Panel.
Installing an LPR
printer
Follow the instructions below to use the standard Windows method
for installing an LPR printer in Windows 2000/XP:
109
110
Section 6: Setting Up - Windows
Windows XP:
Windows 2000:
AXIS 5570e/AXIS 5670e User’s Manual
1. Go to Start | Printers and Faxes and click the Add a Printer icon
to start the Add Printer Wizard. Click Next.
1. Go to Start | Settings | Printers and click the Add Printer icon
to start the Add Printer Wizard. Click Next.
2. Select the appropriate radio button: Local Printer. Click Next.
3. Click the Create a new port radio button and select LPR Port from
the list. Click Next.
4. Enter the name of the server (or its IP address) in the field Name
and address of server providing lpr (Example: AXIS100086) and
enter the port you want to use in the field Name of printer or print
queue on that server (Example: USB1). Click OK.
Ports
USB port
available
AXIS 5570e USB1
AXIS 5670e LPT1
Parallel port
Serial port
LPT1
LPT2
—
COM1
End the wizard in the usual manner: select Manufacturer and
Printer, keep/replace driver, name the printer, make it default or
not, share it or not and finally decide whether you want to print a
test page.
Client/Server Printing
Select Network printer instead of Local Printer in Step 2 above if
your print server has already been installed by the administrator on
another computer. Follow the instructions in the Add Printer Wizard
to complete the installation.
Important!
• Make sure that the Automatically detect and install my Plug and Play
printer checkbox is not checked
• Press F1 to access the Windows online help system if you need additional help
when installing a printer/print server using this method.
AXIS 5570e/AXIS 5670e User’s Manual
Alternative Method for
LPR Printing
Section 6: Setting Up - Windows
If you wish to print over LPR but do not wish to install Print Services
for Unix you can do this by changing the printing protocol after
having installed the printer using the Standard TCP/IP method, see
Adding Printers in Windows 2000/ Windows XP over TCP/IP (LPR), on
page 102 for instructions. LPR is chosen by default with this method.
Once the printer is installed, follow these instructions to change the
printing protocol:
1. Go to Start | Settings | Printers.
2. Double-click the installed printer.
3. Select Properties from the Printer menu.
4. Click the Ports tab.
5. Click the Configure Port button.
6. Click the LPR radio button and enter the queue name (PR1, PR2...).
7. Click OK to finish.
111
112
Section 6: Setting Up - Windows
AXIS 5570e/AXIS 5670e User’s Manual
Adding Printers in Windows NT 4 Using the Microsoft LPR Monitor
If you have not already done so, you should perform the TCP/IP basic
setup procedures prior to installing a printer for LPR printing.
Preparing for
LPR Printing
In the Control Panel, double-click the Network icon. Select the
Services tab. If the TCP/IP Printing entry appears, then TCP/IP is
already installed. Close the Network folder and go on to Installing an
LPR printer, below.
First, prepare for LPR printing:
1. Open the Control Panel and double-click the Network icon.
2. Select Protocols.
3. Add TCP\IP Protocol.
4. Select Services.
5. Add Microsoft TCP\IP Printing.
Installing an LPR
Printer
1. Go to Start | Settings | Printers | Add Printer. Select My
Computer (for peer-to-peer printing) and click Next.
2. From the Available Ports list, choose the appropriate printer port,
which will appear as the host name or IP address of the print server.
Skip to step 7.
3. If the host name or IP address of the print server you wish to use
does not appear in the list, click Add Port.
4. Choose LPR Port from Available Printer Ports and click New Port.
AXIS 5570e/AXIS 5670e User’s Manual
Section 6: Setting Up - Windows
5. Type the print server’s name or IP address in the field Name or
address of server providing lpr (Example: 10.13.6.198). Then
enter which port to use in the field Name of printer or print queue
on that server according to the table below (Example: USB1). Click
OK and then Close.
Ports
USB port
available
AXIS 5570e USB1
AXIS 5670e LPT1
Parallel port
Serial port
LPT1
LPT2
—
COM1
6. The added print server will now appear in the Available Ports list.
7. Click Next, choose an appropriate driver and finish the installation
in the normal manner.
113
114
Section 6: Setting Up - Windows
AXIS 5570e/AXIS 5670e User’s Manual
AXIS Print Monitor Software
AXIS Print Monitor is the recommended tool to use for network
printing in Windows NT, 98 and Me environments.
AXIS Print Monitor is available free of charge on www.axis.com
AXIS Print Monitor
Overview
AXIS Print Monitor allows an AXIS 5570e/AXIS 5670e to be
connected in the same simple fashion as connecting a local printer.
Once installed, it is automatically initialized upon system startup.
AXIS Print Monitor has been developed for peer-to-peer printing,
allowing your print jobs to be sent directly to the print server.
Printing Environments
AXIS Print Monitor supports printing over TCP/IP (LPR and Raw TCP)
and NetBIOS/NetBEUI. To enable printing in these environments,
please ensure that the desired printing protocols are running on your
client.
Peer-to-Peer Printing
The AXIS Print Monitor needs to be installed on each workstation to
perform peer-to-peer printing. Once installed, the AXIS Print Monitor
allows you to access all network printers, just as if they were
connected directly to your workstation.
Client/Server Printing
AXIS Print Monitor needs only to be installed on one server to
perform client/server printing. The installed printers must be
configured to be shared to allow clients to use them. Pop-up
messages should not be enabled on the server as they will not be
displayed on the client platforms.
Note:
AXIS Print Monitor can also be used for DOS printing. Please refer to the AXIS
Print Monitor’s Readme file for instructions. The Readme file is located in the
same folder where AXIS Print Monitor is installed on your PC.
AXIS 5570e/AXIS 5670e User’s Manual
Section 6: Setting Up - Windows
Adding Printers over TCP/IP in Windows NT 4 using AXIS Print Monitor
1. Install AXIS PrintMonitor on all workstations that will print via
the print server.
AXIS PrintMonitor is available free of charge on www.axis.com
2. To start the Add Printer Wizard, select Settings | Printers from the
Start menu and double-click the Add Printer icon.
3. The Wizard asks you to select My Computer or Network printer
server. Select My Computer, click Next.
4. Click Add Port... In the Available Ports dialog, select AXIS Port and
click New Port...
5. Select LPR (TCP/IP) as your choice of protocol and click OK.
6. Enter the IP address or the host name of your print server (Example
IP address: 192.168.3.191 or host name: AXIS181636).
7. In the Logical Printer Name field, enter the port you wish to use;
USB1, LPT1, LPT2 or COM1. Click OK, click Close.
8. Select Manufacturer, Printers, choose a printer name and if you
want to use the printer as your default printer. Choose if you
want to share the printer and print a test page. Click Finish.
9. You may now configure the port, as described below.
Configure the Port:
1. Select Settings | Printers from the Start menu and highlight the
printer you wish to configure. Select File | Properties | Ports and
click Configure Port.
2. Choose whether error condition pop-up messages are to be
displayed by checking the box in the Configure AXIS Ports
dialog. Define the frequency at which the error messages should
be displayed after retry. Click OK.
Even if the desired printer is available in the Manufacturers and Printers lists,
you are advised to use the print driver provided with the printer. This assures
you of the latest driver software.
115
116
Section 6: Setting Up - Windows
AXIS 5570e/AXIS 5670e User’s Manual
Adding NetBIOS/NetBEUI Printers in Windows 2000 using AXIS Print Monitor
See to it that the NetBEUI protocol is installed on your client. Follow
the procedure below to install Axis Printer Ports from a Windows
2000 workstation:
1. To start the Add Printer Wizard, select Settings | Printers from
the Start menu and double-click the Add Printer icon. Start the
installation by clicking Next.
2. The Wizard asks you to select Local printer or Network printer.
Select Local printer. Click Next.
3. Click Create a new port. In the Available Ports dialog, select AXIS
Port and click Next.
4. Select NetBIOS/NetBEUI as your choice of network protocol and
click OK.
5. Select the AXIS Port you want to add from the list of available ports.
The port appears as <name>.<port> (Example: AX100086.LP1). The
<port> is taken from the table below. Click OK.
Ports
USB port
available
AXIS 5570e USB1
AXIS 5670e LPT1
Parallel port
Serial port
LPT1
LPT2
—
COM1
6. Choose the appropriate printer driver for your printer. Click Next
and proceed directly to step 9. It is only necessary to perform steps
7 - 8 if your printer does not appear in the list.
Note:
Even if the desired printer is available in the Manufacturers and Printers lists,
you are advised to use the printer driver provided with the printer. This assures
you of the latest driver software.
AXIS 5570e/AXIS 5670e User’s Manual
Section 6: Setting Up - Windows
7. Click the Have Disk... button. Insert the printer driver diskette/CD
that was provided with your printer, select the appropriate
diskette/CD drive and click OK.
8. Select the printer driver you want to install and click Next.
9. Enter an appropriate name for your printer and click Next.
10. Choose whether you want to share the printer with other network
users and click Next.
11. Choose whether you want to print a test page, click Next and then
Finish.
Adding Printers over NetBIOS/NetBEUI in Windows NT 4 using AXIS Print Monitor
See to it that the NetBEUI protocol is installed on your client. Follow
the procedure below to install Axis Printer Ports from a Windows NT
4.0 workstation:
1. Install AXIS PrintMonitor on all workstations that will print via
the print server.
2. To start the Add Printer Wizard, select Settings | Printers from the
Start menu and double-click the Add Printer icon.
3. The Wizard asks you to select My Computer or Network printer
server. Select My Computer. Click Next.
4. Click Add Port... In the Available Ports dialog, select AXIS Port and
click New Port...
5. Select NetBIOS/NetBEUI as your choice of network protocol and
click OK.
117
118
Section 6: Setting Up - Windows
AXIS 5570e/AXIS 5670e User’s Manual
6. Select the AXIS Port you want to add from the list of available ports.
The port appears as <name>.<port> (Example: AX100086.LP1). The
<port> is taken from the table below. Click OK.
Ports
available
AXIS 5570e
AXIS 5670e
USB port Parallel port
1
US1
LP1
LP1
Parallel port Serial port
2
—
—
LP2
CM1
7. Close the Printer Ports window.
8. Click the Configure Port... button. Choose whether error condition
pop-up messages are to be displayed by checking the box in the
Configure Axis Ports dialog. Define the frequency at which the error
messages should be displayed after retry. Click OK. Continue the
installation by clicking Next.
9. Choose the appropriate printer driver for your printer. Click Next
and proceed directly to step 12. It is only necessary to perform steps
10-11 if your printer does not appear in the list.
Note:
Even if the desired printer is available in the Manufacturers and Printers lists,
you are advised to use the printer driver provided with the printer. This assures
you of the latest driver software.
10. Click the Have Disk... button. Insert the printer driver diskette/CD
that was provided with your printer, select the appropriate
diskette/CD drive and click OK.
11. Select the printer driver you want to install and click Next.
12. Enter an appropriate name for your printer and click Next.
13. Choose whether you want to share the printer with other network
users and click Next.
14. Choose whether you want to print a test page and then click Finish.
AXIS 5570e/AXIS 5670e User’s Manual
Section 6: Setting Up - Windows
Adding Printers in Windows 98 and Me over TCP/IP using AXIS Print Monitor
1. Install AXIS PrintMonitor on all workstations that will print via
the Axis print server.
2. Next, start the Windows Add Printer Wizard: select Settings |
Printers from the Start menu and double-click the Add Printer
icon.
3. After clicking Next in the first dialog, the Wizard asks you to
select between Local Printer and Network Printer. You must
select Local Printer as the print server emulates a local printer
port. Click Next.
4. Choose the appropriate print driver for your printer. If the desired
print driver already appears within the displayed Manufacturers
and printers lists, highlight your selection, click Next and
proceed directly to step 7. It is only necessary to perform steps 56 if your printer does not feature in the model list.
5. Click the Have Disk... button. Insert the printer driver diskette/CD
into the appropriate disk drive of your computer.
6. Select the type of printer you want to install from the
diskette/CD and click Next. If you already have the printer’s
driver installed, you will be asked whether to keep it or to replace
it.
7. Select the Printers@TCP/IP Port and click Next.
8. Enter an appropriate name for your printer and choose whether
you want it to be the default printer. Click Next.
9. In the next window, do not order a Test Page to be written, just
click Finish.
10. The printer you have defined will now be displayed in the Printers
Folder. Right-click the printer object and select Properties.
11. Click the Details tab within the Properties page and then click
Add Port to display the available monitors.
119
120
Section 6: Setting Up - Windows
AXIS 5570e/AXIS 5670e User’s Manual
12. Click the radio button “other”. Select AXIS Port and then click
OK.
13. Select LPR (TCP/IP) as your choice of protocol and click OK.
14. Enter the IP address or the host name of your print server
(Example IP address: 192.168.3.191 or host name: AXIS181636).
In the Logical Printer Name field, enter the port you wish to use;
USB1, LPT1, LPT2 or COM1.
15. The TCP/IP port will then be added automatically to the list of
available ports. Click Apply and OK.
16. You may now configure the port, as described below. The Axis
Printer Port is now installed.
Configure the Port:
1. Select Settings | Printers from the Start menu and highlight the
printer you wish to configure. Select File | Properties | Details
and click Port Settings.
2. Choose whether error condition pop-up messages are to be
displayed by checking the box in the Configure AXIS Ports
dialog. Define the frequency at which the error messages should
be displayed after retry. Click OK.
Note:
Even if the desired printer is available in the Manufacturers and Printers lists,
you are advised to use the print driver provided with the printer. This assures
you of the latest driver software.
AXIS 5570e/AXIS 5670e User’s Manual
Section 6: Setting Up - Windows
Adding Printers in Windows 98 and Me over NetBIOS/NetBEUI using AXIS Print
Monitor
Follow the procedures below to install Axis NetBIOS/NetBEUI printer
ports on a Windows 98 workstation, using AXIS Print Monitor:
1. To start the Add Printer Wizard, select Settings | Printers from
the Start menu and double-click the Add Printer icon.
2. After clicking Next in the first dialog, the Wizard asks you to select
Local printer or Network printer. Select Local printer. Click Next.
3. Choose the appropriate printer driver for your printer. If the desired
printer driver appears in the displayed Manufacturers and Printers
lists, highlight your selection, click Next and proceed directly to
step 6. It is only necessary to perform steps 4 - 5 if your printer does
not appear in the model list.
Note:
Even if the desired printer is available in the Manufacturers and Printers lists,
you are advised to use the printer driver provided with the printer. This assures
you of the latest driver software.
4. Click the Have Disk... button. Insert the printer driver diskette/CD
that was provided with your printer, select the appropriate
diskette/CD drive and click OK.
5. Select the printer driver you want to install and click Next.
121
122
Section 6: Setting Up - Windows
AXIS 5570e/AXIS 5670e User’s Manual
6. Select the AXIS Printer Port from the Available Ports list. The port
names appears as <name>.<port>. Here, <name> is AX followed
by the last six digits of the print server’s serial number (e.g.
AX100086) and <port> is taken from the table below. Click the
Configure Port button.
Ports
available
AXIS 5570e
AXIS 5670e
USB port Parallel port
1
US1
LP1
LP1
Parallel port Serial port
2
—
—
LP2
CM1
Example: AX100086.US1
7. Choose whether error condition pop-up messages are to be
displayed by checking the box in the Configure AXIS Ports dialog.
Define the frequency at which the error messages should be
displayed after retry. Click OK and Next.
8. Enter an appropriate name for your printer and click Next.
9. Choose whether you wish to print a test page and click Finish.
AXIS 5570e/AXIS 5670e User’s Manual
Section 7
Section 7: Setting Up - NetWare
Setting Up - NetWare
This section describes how to continue the installation of the AXIS
5570e/AXIS 5670e in the NetWare environment. Identify which
transport protocol you are running on your network and which
installation method you should use. Continue the installation by
selecting the appropriate installing instructions from the table below:
Installation
method
Transport
protocol
Action
NDPS
TCP/IP
See “Setup using NDPS” on page 124.
IPX/SPX
- Public Access Printers, on page 124
- Controlled Access Printers, on page 130
iPrint
iPrint over LPR
See “Setup using iPrint” on page 143.and
See “Install a printer using AXIS LPR
Gateway Configuration Snapin” on page 146.
iPrint over IPP
See “Setup using iPrint” on page 143.and
See “Install a printer with AXIS IPP Gateway
Configuration Snapin” on page 145.
Queue-based
printing
IPX/SPX
Basic
Configuration
IPX/SPX
Advanced
configuration
To install using the AXIS NetPilot Installation
Wizard,
See “Basic Setup with AXIS NetPilot” on
page 149..
If you need a more advanced installation
that is not covered by the AXIS NetPilot
Installation Wizard,
See “Advanced Installation using AXIS
NetPilot” on page 150..
See “NetWare Administration” on page 156. for information on
Novell’s administration tools.
If you intend to operate your AXIS 5570e/AXIS 5670e in a multiprotocol, mixed environment, you should also proceed to the other
relevant sections in this manual.
123
124
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
Setup using NDPS
The AXIS 5570e/AXIS 5670e supports Novell Distributed Print
Services (NDPS). You can run NDPS over Pure IP (TCP/IP) or IPX/SPX.
Before the AXIS 5570e/AXIS 5670e can be installed, make sure that
NDPS is installed and a Broker is loaded on your NetWare file server.
AXIS 5570e/AXIS 5670e uses the AXIS NDPS Gateway for printing in
networks using either IP or IPX as transport protocols. The printer
gateways are included with the NDPS software (from version 5.1 and
up) and are automatically installed together with NDPS.
Note:
NDPS requires that you run NetWare 4.11 or higher. Pure IP is only supported by
NetWare 5 or higher.
Installing the AXIS
5570e/AXIS 5670e in
the NDPS
environments
Having assigned an IP address to the AXIS 5570e/AXIS 5670e as
described in Assigning an IP Address to the Print Server, on page 14,
you are now ready to install the AXIS 5570e/AXIS 5670e for NDPS
printing. You can select to install the connected printers as public or
controlled access printers. Follow the instructions below to install the
AXIS 5570e/AXIS 5670e using NDPS:
Important:
Public Access Printers
•
The NDPS Enabled parameter of the AXIS 5570e/AXIS 5670e must be set to
Yes in order for the communication between the print server and the NDPS
gateway to be enabled. To change this parameter, log in to the print server’s
web pages and choose: Admin => Network Settings=> Detailed View=>
NetWare=> NDPS Enabled => Yes.
•
If you do not have an NDPS Manager object available, start out with creating
one in the NetWare Administrator.
Follow these instructions to create a public access printer using the
NDPS Manager object in your NetWare administrator utility:
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
1. Double-click on the NDPS Manager object you will be using to
control the Printer Agents.
2. On the Identification page for the NDPS Manager, click the printer
Agent List button. The Printer Agent List dialog will appear.
3. Click New. The Create Printer Agent dialog will appear.
4. Type a name of your choice in the NDPS Printer Agent field:
5. Select the Axis Gateway configuration in the Gateway Type
window.
6. Click OK
125
126
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
7. In the Select the printer’s type window, choose your printer. If you
cannot find the printer, select an appropriate Generic one (PCL, PS,
etc)
8. Select TCP/IP (default) or IPX as network protocol. Click Next.
9. You will find the print server in the next window with the printer
attached on the connected port. Depending on the transport
protocol you used when you start the installation, the print server
should appear as following:
•
TCP/IP Network protocol:
IP Address and Port, e.g: 192.168.70.243 and LPT1
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
1. Only the ports with a connected printer show up in this window.
If the printer is not in the displayed print list, click Manually
specify the print server and do the following:
Enter the Print Servers’ IP address in the IP Address Field
2. Choose a port in the Print Server Port field
e.g., 192.168.70.243 and LPT1
The available ports are :
Ports available
AXIS 5570e
AXIS 5670e
*USB1 port
other/unknown
-
Parallel port 1
LPT1
LPT1
Parallel port 2
—
LPT2
Serial port
—
COM1
(Example: “other/unknown”, stands for the USB1 port.)
IPX Network protocol:
All the available ports will be presented, regardless if the printers
are or not connected to those ports, e.g.
LPT1
AXIS5FF66A_P1
LPT2
AXIS5FF66A_P2
USB1
AXIS5FF66A_P2
COM1
AXIS5FF66A_P3
127
128
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
The IPX Addresses for the above printers will appear as:
<IPX External Network Number>:<Print Server’s HW
address>:<Socket Number>
i.e.: 01d7e1c2:00408c5ff6a6:400c
where 400c, 401c, and 402c are the socket numbers corresponding the LPT1, LPT2, USB1 and COM1 physical ports:
LPT1
400c
LPT2
401c
USB1
401c
COM1
402c
If the printer is not in the displayed print list, click Manually
specify the print server and do the following:
1. Enter the <IPX External Network Number> in the Network field.
2. Enter the <Print Server’s HW address> in the LAN HW address field.
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
3. Choose a port in the Print Server Port field, e.g.
01d7e1c2:00408c5ff6a6 and LPT1
The port numbers are USB1*, LPT1, LPT2 or COM1.
Ports available
AXIS 5570e
AXIS 5670e
*USB1 port
Parallel port 1 Parallel port 2 Serial port
other/unknown
LPT1
—
—
LPT1
LPT2
COM1
(Example: other/unknown, which stands for the USB1 port.)
4. When done, select your printer and click Finish.
5. Next, select the printer drivers for each client operating system.
(Windows 2000, Windows NT4 and Windows 95/98). These drivers
will be automatically downloaded to users’ workstations when they
install this printer in the future.
129
130
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
6. Click Continue and OK in the next NDPS window. The new Printer
Agent appears in the Printer Agent List window.
Check the Status: it should be Idle.
7. Press Cancel to close the NDPS Manager
To install the printer on the workstation, See “Installing an NDPS
Printer on the Workstation” on page 137.
Controlled Access
Printers
Follow these steps to create a controlled access printer as an object
in the Directory Tree, using the NetWare administrator utility:
1. Log in as Admin.
2. Start the NW Admin utility on any Workstation
(SYS:PUBLIC\WIN32\nwadmin32.exe).
3. Browse the context your NDPS Manager resides in.
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
4. From the Object menu, select Create. The New Object dialog
appears.
5. Select NDPS Printer. The Create NDPS Printer dialog appears.
131
132
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
6. Type a name of your choice in the NDPS Printer Name field, e.g.
AXIS5FF66A_IPX1
In the Printer Agent Source field, select the source of the Printer
Agent. The following options are available:
- Create a New Printer Agent. If you select this option, you are
asked to select either the Novell Gateway or a third party Gateway.
- Printer Agent on Existing NDS Object. Use a Printer already
configured as a controlled access printer (NDPS Printer Object).
If you select this option, a list of current NDPS Printer Objects in
this container will be displayed from which you can select the one
you want to use.
- Public Access Printer Agent. Use an existing Printer Agent
representing a Public Access Printer.
7. Select Create a New Printer Agent and click Create to display the
Create Printer Agent dialog.
8. Confirm the Printer Agent name (default is the name of the new
printer you are creating) and browse to select the NDPS Manager
to which you want to assign it
9. Select AXIS Gateway Configuration in the Gateway Type field.
10. Click OK.
11. In the Select the printer’s type window choose your printer. If you
cannot find the printer, select an appropriate Generic one (PCL, PS,
etc)
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
12. Select TCP/IP (default) or IPX as network protocol.
13. Click Next.
14. You will find the print server in the next window with the printer
attached on the connected port.
Depending on the transport protocol you used when you start the
installation, the print server will appear as:
•
TCP/IP Network protocol:
IP Address and Port, e.g.
192.168.70.243 and LPT1
Only the ports with a connected printer will show up in this
window.
133
134
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
If the printer is not in the displayed print list:
1. Click Manually specify the print server enter the Print Servers’
IP address in the IP Address Field.
2. Choose a port in the Print Server Port field e.g., 192.168.70.243
and LPT1:
The port numbers are USB1*, LPT1, LPT2 or COM1.
Ports available
AXIS 5570e
AXIS 5670e
*USB1 port
other/unknown
-
Parallel port 1
LPT1
LPT1
Parallel port 2
—
LPT2
Serial port
—
COM1
(Example: other/unknown, stands for the USB1 port.)
IPX Network protocol:
All the available ports will be presented, regardless if the printers
are or not connected to those ports,.
LPT1
AXIS5FF66A_P1
LPT2
AXIS5FF66A_P2
USB1
AXIS5FF66A_P2
COM1
AXIS5FF66A_P3
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
The IPX Addresses for the above printers will appear as:
<IPX External Network Number>:<Print Server’s HW
address>:<Socket Number>
i.e.: 01d7e1c2:00408c5ff6a6:400c
where 400c, 401c, and 402c are the socket numbers corresponding the LPT1, LPT2, USB1 and COM1 physical ports:
LPT1
400c
LPT2
401c
USB1
401c
COM1
402c
If the printer is not in the displayed print list:
1. Click Manually specify the print server and enter the <IPX
External Network Number> in the Network field.
2. Enter the <Print Server’s HW address> in the LAN HW address
field.
135
136
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
3. Choose a port in the Print Server Port field:
e.g.: 01d7e1c2:00408c5ff6a6 and LPT1.
The port numbers are USB1*, LPT1, LPT2 or COM1.
Ports available
AXIS 5570e
AXIS 5670e
*USB1 port
Parallel port 1 Parallel port 2 Serial port
other/unknown LPT1
—
—
LPT1
LPT2
COM1
(Example: other/unknown, stands for the USB1 port.)
4. When done, select your printer and click Finish.
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
5. Next, select the printer drivers for each client operating system.
(Windows 2000, Windows NT4 and Windows 95/98). These drivers
will be automatically downloaded to users’ workstations when they
install this printer in the future.
6. Click Continue and OK in the next NDPS window. Your printer will
appear as an NDS object in the Directory Tree and will offer a full
range of network security options.
To install the printer on the workstation, See “Installing an NDPS
Printer on the Workstation” on page 137.
Installing an NDPS
Printer on the
Workstation
To install the printer on a workstation, use either Novell Printer
Manager (NetWare 5.1 only) or the Add Printer Wizard on the local
workstation.
137
138
Section 7: Setting Up - NetWare
Using Novell Printer
Manager
AXIS 5570e/AXIS 5670e User’s Manual
1. Log in as Admin.
2. On the any workstation, browse to
<NW 5.1 File Server>\SYS:PUBLIC\Win32
and start Nwpmw32.exe (Novell Printer Manager).
The Novell Printers dialog appears, displaying a list of installed
Public or Controlled printers (if any printers have previously been
installed on the workstation).
3. From the Printer Manager’s Printer pull down menu, select New.
4. Click Add. A list of available printers appears.
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
5. The list of available printers shows the NDPS Public Access Printers
on the network and the NDPS Controlled Access Printers in you
current NDS context. To see the Controlled Access Printers in other
context that you have rights to, click the Browse button and select
your choice. Click OK.
6. Once selected, click Install. The Novell Printers – Install dialog
appears.
139
140
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
7. Click OK. The default driver for that printer is then automatically
downloaded.
If the printer object does not have a printer driver associated with
it, or a driver was not found, you will be prompted to either to
choose from a list of printer drivers provided by NDPS or to provide
a disk with the appropriate driver.
The Novell Printers dialog appears with the new printer, e.g.
AXIS5FF6A6_IPX1 in the installed list.
8. Click Close.
In the Novell Printer Manager window the new installed NDPS
printer appears with the name e.g. AXIS5FF6A6_IPX1 and is
available for print jobs.
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
9. Verify by clicking Start - Settings - Printers on the workstation.
Using the Add Printer
Wizard
1. Click Start on your workstation, select Settings =>Printers.
There might be some differences regarding this menu depending
of MS Operating System you are running.
2. Start the Add Printer Wizard on the workstation. The Add Printer
Wizard dialog will appear. Click Next.
141
142
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
3. Select Network printer and click Next.
4. Click Next again in the Locate Your Printer dialog (Win2000/XP)
or press the Browse button (Win9X)
5. Browse to the NDPS Printers. Expand either the NDPS Controlled
Access Printers or the NDPS Public Access Printers folder, select
your newly installed NDPS printer and follow the instructions.
When you have completed these steps, you are ready to start
printing.
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
Notes:
• The Public Access print servers are immediately available for everyone on the
network
• The Axis Gateway Configuration Utility is an installation and configuration tool
for NDPS printers in the NetWare environment.
The Axis Gateway will appear in NetWare 5.1 and later releases. You can
download the Axis Gateway Configuration Utility for use with earlier versions of
NetWare from www.axis.com.
• To print using TCP/IP, Axis print server firmware 6.1 or later is required. In order
to print using IPX/SPX, Axis print server firmware 5.51 or later is needed.
Setup using iPrint
iPrint is Novell's next generation of printing software that lets users
print to and from all destinations.
A standard Web page displays available printers to the user.
By clicking a printer, the iPrint client is installed (if not installed
previously), the printer's driver is downloaded, and a printer is created
in the user's Printer folder, enabling the user to send documents to
the printer from any application on the desktop.
Before setting up iPrint printers, make sure that you meet all the
iPrint Setup requirements. See the Novell iPrint Administration Guide
for instructions on installing, configuring, and customizing iPrint.
AXIS Print servers can be installed as iPrint printers, either by using
the Novell LPR gateway (LPR on IP) or the AXIS Gateway
Configuration Snap-in for iPrint.
Axis provides two Snap-ins for iPrint:
•
•
AXIS LPR Gateway Configuration
AXIS IPP Gateway Configuration
143
144
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
When you install Service Pack 6 (16 April 2003) for NetWare 5.1 or
later and Service Pack 3 (16 April 2003) for NetWare 6.0 or later, the
AXIS LPR Gateway Configuration will automatically be installed and
configured on the NetWare Servers and ready for use.
The AXIS IPP Gateway Configuration Snap-in for NetWare 6.0 can be
downloaded for free from www.axis.com. Follow the instructions
below to install the AXIS IPP Gateway Configuration Snap-in for
NetWare 6.0, if you want to add it in your iPrint environment.
Installing AXIS IPP
Gateway
Configuration Snapin for NetWare 6.0
1. Download the free axisIPP-snap-in.zip file from www.axis.com
and unzip it in a temporary directory.
2. Make sure the the NetWare Enterprise Web Server was previously
installed on the server. Otherwise, install it.
3. Novell iPrint uses the NDPS infrastructure, so make sure that all the
NDPS requirements have been met:
• Make sure that the BROKER.NLM is loaded. If it isn’t, type
LOAD BROKER in the server console prompt and select the
name of the Broker.
• Make sure that the NDPS Manager object is created in the
Novell Directory Services (NDS) tree. Refer to your Novell
documentation for creating this object.
• Make sure that the NDPSM.NLM is loaded. If it isn’t, type
LOAD NDPSM in the server console prompt and select the
appropriate NDPS Manager.
4. Shutdown Tomcat and the NetWare Enterprise Web Server on the
NetWare file server by executing the following commands:
Type "NSWEBDN" <Enter>
Type "TOMCAT33 -STOP" <Enter>
Type "NVXADMDN" <Enter>
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
5. Map the next available drive (e.g. G:) to the root of volume SYS on
your NetWare server.
From the temporary directory where axisIPP-snap-in.zip has been
unzipped, run the batch file AxisIPP.bat (default G:).
If the drive G: is not available, you have to edit the batch file and
change the drive to next available one.
Check that each line in the batch file is executed without failure.
6. Restart Tomcat and the NetWare Enterprise Web Server on the file
server by executing the following commands:
Type "TOMCAT33" <Enter>
Type "NVXADMUP" <Enter>
Type "NSWEB" <Enter.
7. Access the iManager web page on the NetWare server by opening
the following URL:
https://<IP address of NW server>:2200/eMFrame/iManager.html
You have to authenticate.
8. Click on iPrint Management on the left pane and select Create
Printer.
9. On the right pane, verify that the newly installed AXIS IPP Gateway
Configuration is under the Gateway type drop-down menu.
If not, it may be necessary to restart the NetWare server.
Now you are ready to use the AXIS IPP Gateway Configuration for
installing iPrint printers. You have to have Administrator rights to
install the printers through iPrint.
Install a printer with
AXIS IPP Gateway
Configuration Snapin
1. Use an AXIS 5570e/AXIS 5670e and connect a printer to
whatever port you want.
2. Connect the print server to the network.
3. Connect the power supply.
4. Start both the printers and the print server.
5. Log in as Admin.
145
146
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
6. Use a web browser and the local host URL to login into iManager
on your NetWare server.
7. Open your browser to the following URL:
https://<IP address of NW server>:2200/eMFrame/iManager.html
You have to authenticate.
8. Click on iPrint Management on the left pane.
9. Click on Create Printer.
10. Choose a name of your choice for the printer
11. Choose the context where the printer will be installed.
12. Browse for the NDPS Manager and select it.
13. In the Gateway Type drop-down list, choose the Axis IPP Gateway
Configuration. Press Next.
14. In the Printer URL, you may choose either the IPP version 1.0 format:
http://<IP address of your print server>:631/lptx
or the IPP version 1.1:
ipp://<IP address of your print server>/lptx
where x is the port number. Click Next.
15. Select default drivers for your printer. Click Next and OK.
Install a printer using
AXIS LPR Gateway
Configuration Snapin
1. Use an AXIS 5570e/AXIS 5670e and connect a printer to
whatever port you want.
2. Connect the print server to the network.
3. Connect the power supply.
4. Start both the printers and the print server.
5. Log in as Admin.
6. Use a web browser and the local host URL to login into iManager
on your NetWare server.
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
7. Open your browser to the following URL:
https://<IP address of NW server>:2200/eMFrame/iManager.html
You have to authenticate.
8. Click on iPrint Management on the left pane.
9. Click on Create Printer.
10. Choose a name for the printer.
11. Choose the context where the printer will be installed.
12. Browse for the NDPS Manager and select it.
13. In the Gateway Type drop-down list, choose the Axis LPR Gateway
Configuration. Click Next.
14. Choose either the IP address or the DNS Name for your print server.
15. Under Printer name, select the physical printer port, e.g. LPT1, or
logical printer port pr1-pr8 using the drop-down list. Click Next.
16. Select default drivers for your printer. Click Next and OK.
Installing the iPrint
Printer on the
Workstation
An iPrint printer can by locally installed on the workstation in two
ways:
•
•
Using the iPrint Client
Using the MS Add Printer Wizard at the workstation.
See “Using the Add Printer Wizard” on page 141.)
147
148
Section 7: Setting Up - NetWare
Installing the iPrint
Printer using the
iPrint Client.
AXIS 5570e/AXIS 5670e User’s Manual
In order for users to use iPrint, they need to install the Novell® iPrint
Client software and a printer. When a user selects a printer to be
installed by iPrint, iPrint checks to see if the Novell iPrint Client
software is installed and then installs it if necessary. Then the printer
driver is downloaded and the printer is installed in the user's Printer
folder.
In order for iPrint to work properly, the workstation should have the
following:
•
•
Windows 95/98/Me or Windows NT*/2000/XP
Web browser with JavaScript enabled:
• Microsoft Internet Explorer 5.0 or later
• Netscape 4.76 (iPrint is not supported on Netscape 6)
The user should use the following iPrint url:
http://<IP address of your NW server>:631/IPP
1. From a Netscape or Internet Explorer browser, enter the provided
URL.
A Web page displays a listing of available printers to install and a
link to install the client software.
2. Select Install iPrint client software to locally install the iPrint
printers. If you try to install a printer before installing the iPrint
client software, you will be prompted to install the client software
first.
If you associate a printer driver with a printer being installed, the
driver is automatically installed on the user's workstation. If the
driver already exists, that driver is overwritten even if it is a newer
driver.
3. After installing a printer, it is added to the user's Printer folder.
Users can print to the printer by selecting it from any application.
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
Basic Setup with AXIS NetPilot
Install the AXIS NetPilot software on your computer. AXIS NetPilot
runs on any of these Windows platforms; Windows 98 and Windows
NT.
Starting the
Installation
Follow the instructions below to install the AXIS 5570e/AXIS 5670e
with AXIS NetPilot:
1. Start AXIS NetPilot by double-clicking the NetPilot icon, which is
located in the folder where you installed AXIS NetPilot.
2. Locate the AXIS 5570e/AXIS 5670e in the ‘New Axis Units’ folder.
Select it and click the Install button on the AXIS NetPilot toolbar.
If your network is large, it could take a few seconds before the print
server appears in the folder.
Choose the with Installation Wizard option.The AXIS NetPilot
Installation Wizard guides you through the installation process. The
following options are available:
Note:
The number of options varies according to the number of environments you
enable.
Print Server Name
The default print server name consists of the characters ‘AXIS’
followed by the last six digits of the serial number. If you want to
change the print server name, just type the new name in the available
text field.
Environments
Choose which networking environments you want to configure the
AXIS 5570e/AXIS 5670e for, e.g. NetWare, TCP/IP, Windows & OS/2 or
Macintosh. If your network comprises various different platforms, you
can enable any combination of environments.
NetWare NDS
Place NetWare Print Queues on a specific bindery server, or
alternatively into an NDS Tree.
149
150
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
The IP address
Choose the method the AXIS 5570e/AXIS 5670e should employ for
obtaining an IP address. DHCP, ARP, RARP, BOOTP and Auto-IP are
supported. You can also select to set the IP address manually. Refer
to Assigning an IP Address to the Print Server, on page 14 for further
information about setting the IP address.
Print Queues
The AXIS 5570e/AXIS 5670e uses the print server name followed by
the printer port as the default Print Queue name and print server port
name. If you want to change the default printer queue names, just
type the new names in the available text fields.
Test Page
The final user prompt in the Installation Wizard allows you to print a
test page through NetWare. The test page displays the name of all
the NetWare servers the AXIS 5570e/AXIS 5670e is connected to and
shows the status of each connection.
Unless you want to connect or create additional printing queues, the
installation for the NetWare environment is now completed.
Notes:
•
The parameters entered during installation are not permanent; they can be altered
at any time according to your network printing requirements.
•
No serious or permanent damage will be caused if you make a mistake during
installation. If you find, at any time, that printing is not satisfactory, the parameters can easily be changed to tune the system to your requirements.
•
For information on advanced functions, please refer to the AXIS Network Print
Server Technical Reference. You can download this or other technical information
over the Internet by accessing www.axis.com
Advanced Installation using AXIS NetPilot
Having installed your AXIS 5570e/AXIS 5670e print server in
accordance with the basic installation procedures described in Basic
Setup with AXIS NetPilot, on page 149, your AXIS 5570e/AXIS 5670e
print server should now feature in the ‘Network Print Servers’ folder
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
located in the AXIS NetPilot main window.
NetWare Network
Environment Window
The NetWare Network Environment window allows you to connect
additional print queues to your AXIS 5570e/AXIS 5670e as well as
create new ones.
Follow the steps below to gain access to the NetWare Network
Environment window:
1. Select the required Network Print Server from the ‘Network Print
Server’ folder.
2. Choose Network from the Setup menu or click on the Network icon
on the AXIS NetPilot’s toolbar.
If you are not logged on to your NetWare file server, a dialog box will
ask you to log on.he AXIS 5570e/AXIS 5670e periodically updates the
configuration by scanning the NDS tree or, in the case of NetWare
versions 3.x, the designated file servers.
Connecting
Print Queues
Follow the steps below to connect a print queue to the print server
port:
1. Open the NetWare ’Network Environments’ window.
2. Select the print server port you want to connect.
151
152
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
3. Click the Connect... button. The Connect NetWare Print Queues
window appears.
The AXIS NetPilot Connect NetWare Print Queues window
4. Select the tree or server location of the print queue from the
Resources box.
5. Select an existing print queue to connect to the server port, or
create a new print queue by clicking on Create Queue... If you have
selected an existing queue, advance to step 8. Continue with step
6 only if you want to create a new queue.
6. Type the queue name in the Create Queue dialog window. If you
want to create a queue in the NDS tree you must also enter the
name of the volume where the queue will be located. Click OK.
7. Select the newly created queue from the queue list.
8. Select Print Server Mode or Remote Printer Mode. If you selected
Print Server Mode, advance directly to step 11, otherwise continue
with step 9.
9. Select an appropriate NetWare Print Server name, that will be
associated with the AXIS 5570e/AXIS 5670e print server, by using
the Browse... button.
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
Notes:
•
You cannot type or edit the name manually.
•
Make sure that you have PSERVER.NLM running if you selected Remote
Printer Mode in step 8.
10. If you want to define a remote printer number slot manually, check
the Manual box and type the desired number in the box.
11. Click the OK button to return to the Network Environments
window.
Basic Queue-based printing over IP
Axis print servers with software version 6.0 or later allow users to
print in a Pure IP environment using traditional queue-based printing
(which usually uses the IPX transport protocol). Note that only NDS
queue-based printing is supported.
In the NetWare Pure IP environment, you must use the NetWare
Administrator to create the printer, print server and queue objects.
Installing the
AXIS 5570e/AXIS
5670e
Follow the instructions below to install the AXIS 5570e/AXIS 5670e
in the NetWare Pure IP environment:
1. Start the Configuration Wizard from the User mode in the AXIS
5570e/AXIS 5670e Web interface.
2. Click your way through the Wizard until reaching the NetWare
page.
153
154
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
3. Set the parameters on the NetWare page:
• PSERVER NDS Tree (example: NW5TREE)
or
PSERVER NDS File Server: (example: FILESERVERNAME)
• PSERVER NDS Distinguished Name:
(example: AXISXXXXXX.<context>, where <context> is the
container where you want to create your print server)
Setting the PSERVER parameters in the AXIS 5570e/AXIS 5670e Web interface.
4. Use the NetWare Administrator to create the printer, print server
and queue objects in the NDS tree and then link them together. The
Print Services Quick Setup (Non-NDPS) utility can be used for this.
Go to Tools in the NetWare Administrator.
5. Use the Add Printer Wizard on your work station to install the
printer on your client. Note that only NDS queue based PSERVER
printing is supported. When installing, choose Network Printer and
browse to the queue you have just created. Alternatively, choose
Local Printer and select the queue you have just captured.
Any configuration and management of the AXIS 5570e/AXIS 5670e
can be performed from any standard Web browser. Please refer to
AXIS 5570e/AXIS 5670e User’s Manual
Section 7: Setting Up - NetWare
Using a Web Browser for Print Server Management, on page 86.
If both the IPX and IP protocols are enabled in your network and the
print server uses DUAL_STACK (enabled by default) as its network
transport protocol, then IPX will be chosen. To force the print server
to use the IP transport protocol, go to your print server’s web
interface and choose Admin | Detailed View | NetWare and change
the NetWare Transport Protocol from DUAL_STACK to IP_ONLY. Save
and exit when finished.
Note:
Pure IP requires that you run NetWare 5 or higher.
Queue-based Printing
Methods
Print Server Mode
The following overview explains the advantages and limitations of
the two supported queue-based printing methods.
The AXIS 5570e/AXIS 5670e logs in to a file server(s) and repeatedly
polls the print queues for print jobs. In this fashion, the AXIS
5570e/AXIS 5670e emulates a NetWare print server, which is a
workstation running PSERVER. It provides high printing speed with
low network load and is the recommended mode for medium to large
sized networks. Each print server in PSERVER mode takes one
NetWare user license.
Advantages
•
High performance:
Limitations
•
In bindery mode, this printing method requires a NetWare user
licence for each AXIS 5570e/AXIS 5670e to file server link.
Remote Printer Mode
The AXIS 5570e/AXIS 5670e acts as Remote Printer for PSERVER.NLM
running on the NetWare file server, or to a dedicated workstation
running PSERVER.EXE. In this fashion, the AXIS 5570e/AXIS 5670e
emulates a workstation running the NetWare remote printer software
RPRINTER, or NPRINTER. This mode is only recommended for small
networks where the number of NetWare user licences is a major
issue.
155
156
Section 7: Setting Up - NetWare
AXIS 5570e/AXIS 5670e User’s Manual
Advantages
•
NetWare user licences are not required.
Limitations
•
•
Lower performance, typically 20 - 70 kbytes/s for NLM.
Higher network load.
Using Novell Utilities
After installing the AXIS 5570e/AXIS 5670e into the NetWare
environment, you can manage your AXIS 5570e/AXIS 5670e, using
either Novell’s NetWare Administrator, or PCONSOLE.
NetWare Administration
Some useful features provided by the NetWare Administrator are
described in more detail below:
Printer Status
The Printer Status menu, detailed below, shows the status of an
active print job serviced by an AXIS 5570e/AXIS 5670e network print
server. It displays detailed information concerning the active job
including, Print Queue, print job description, size of print file,
percentage of job completed, etc. You can also abort or pause the
print job from this menu.
Notification
You can use the NetWare Administrator to enable or disable status
notification messages for printers connected to the AXIS 5570e/AXIS
5670e, e.g. Busy, Off-line, Out of paper, Paper jam, etc. You can also
add or remove print job owners and administrators from the list of
persons to be notified.
AXIS 5570e/AXIS 5670e User’s Manual
Print Layout
Section 7: Setting Up - NetWare
You can view installed AXIS 5570e/AXIS 5670e and their relative
print queues for any NetWare Organizational Unit. You can also display summary information by right-clicking on the printer object you
want to examine.
157
158
Section 8: Setting Up - Macintosh
Section 8
AXIS 5570e/AXIS 5670e User’s Manual
Setting Up - Macintosh
Having connected the AXIS 5570e/AXIS 5670e to your network, this
section now describes how to set up your print server for printing in
Mac OS X and earlier Macintosh environments using AppleTalk.
If you intend to use the print server in a multi-protocol environment,
refer to the chapters pertaining to the respective operating systems
in this manual.
Installation in Mac OS X
This section describes setting up your print server for printing in the
Mac OS X.
1. Start Print Center (from Go | Applications | Utilities | Print
Center)
2. Select Printers | Add Printer...
3. From the Printer List dialog, select AppleTalk.
4. Now, the ports of your print server will appear in the list of available
printers. The port is shown as <host name>_<port>.
Example: AXIS100086_LPT1.
5. Select the print server port you want to use.
6. Select an appropriate printer driver for your printer from the Printer
Model drop-down list. If the printer is not available in the list, select
Generic.
(You can also browse for a printer driver on your computer or
network by selecting Other... from the list.)
7. Click Add to complete the installation.
AXIS 5570e/AXIS 5670e User’s Manual
Section 8: Setting Up - Macintosh
Note:
If you want to print using LPR, select:
1. Printers | Add Printer...
2. From the Printer List dialog, select LPR printers using IP.
3. Enter the IP address or host name of the print server in the LPR
printer’s Address field. You must uncheck the Use Default
Queue on Server check box and enter a Queue Name:
Physical ports: USB1, LPT1, LPT2 or COM1
4. Choose a printer driver from the Printer Model list and click Add
to finish.
Installation on MacOS 9.1 or older, using AppleTalk
Basic Configuration
On MacOS 9.1 or older, basic configuration in AppleTalk is performed
simply by opening the Chooser window and selecting a printer.
You can change the default name of your print server or any of
default parameters by editing the print server’s config file. To access
the config file from a Macintosh, you can use:
• any Web browser with Javascript enabled
• FTP using MacTCP, Fetch or Anarchie
In order to use any of these methods, you must assign an IP address
to the print server as described in Setting Parameters, on page 163.
159
160
Section 8: Setting Up - Macintosh
AXIS 5570e/AXIS 5670e User’s Manual
Choosing a Printer
Selecting a Printer
The method for choosing a printer varies depending on which version
of LaserWriter printer driver you are using.
•
•
Autodetect Printer
Type
The LaserWriter 7.0 driver assumes that you use a standard
PostScript driver, and cannot take advantage of any printer
specific features.
The LaserWriter 8.0 driver uses PPD files that contain printer
descriptions. This gives you full control over any features your
printer might have.
The print server can automatically detect the type of printer you are
using if you enable Autodetect Printer Type. The print server can
then recognize Epson and Hewlett Packard InkJet printers. Most
Epson and Hewlett Packard InkJet printers that have Mac OS printer
drivers for network printing are supported. Without the Autodetect
Printer Type function, the AppleTalk printer type has to be specified
manually in the print server. For Epson InkJets it would be
"EPSONLQ2" and for HP InkJets it would be "DeskWriter". If the print
server does not recognize the connected printer, the default setting
"LaserWriter" will be used as printer type. "LaserWriter" is the
recommended setting to be used with all PostScript printers.
To enable Autodetect Printer Type, log in to your print server’s Web
interface and select Admin | Network Settings | Detailed View |
Macintosh | Auto Detect Printer Type | Yes.
See the Help pages in the print server’s Web interface for details.
LaserWriter 7.0
Printer Driver
Follow the instructions below to choose a printer:
1. Select Chooser from the Apple menu.
2. Click the LaserWriter icon.
3. If your network has more than one zone, click on the zone you want.
(If your network does not have any zones, this box will not appear.)
AXIS 5570e/AXIS 5670e User’s Manual
Section 8: Setting Up - Macintosh
4. Click the name of the printer you want — the ports are shown as
<host name>_<port>. Example: AXIS100086_USB1.
5. Click the Close box. This completes the configuration and closes the
Chooser.
Repeat this procedure for each Macintosh computer on the network
using the print server.
LaserWriter 8.0
Printer Driver
Follow the instructions below to choose a printer:
1. Select Chooser from the Apple menu.
2. Click the LaserWriter 8.0 icon.
3. If your network has more than one zone click on the zone you want.
(If your network does not have any zones, this box will not appear.)
4. Click the name of the printer you want — the ports are shown as
<host name>_<port>. Example: AXIS100086_USB1.
5. Click Setup... and then Auto Setup. If the selected printer
supports bi-directional printing and the appropriate PPD file is
available, the installation is performed automatically and you
can therefore proceed directly to step 7 (if this is not the case,
the PPD file must be selected manually, as described in step 6).
6. Choose the PPD file matching your printer, and click OK.
If your printer does not appear in the PPD file list, please contact
your printer vendor. Use the Generic PPD if you do not need any
printer specific features.
7. Click OK, and then click the Close box. This completes the
configuration and closes the Chooser.
Repeat this procedure for each Macintosh computer on the network
using the print server.
Bi-directional
Support
The AXIS 5570e/AXIS 5670e allow the printer driver to communicate
directly with the printer and consequently facilitates complete
functional control over print jobs, e.g. automatic downloading of
fonts not resident in the printer.
161
162
Section 8: Setting Up - Macintosh
AXIS 5570e/AXIS 5670e User’s Manual
This functionality has backward compatibility with older printers and
Macintosh computers, which means that the AXIS 5570e/AXIS 5670e
can generate appropriate responses to Macintosh printer queries
when the connected printer does not support bi-directional
communication.
Verifying the Setup
You simply need to print a document from the Macintosh computer
to verify communication to the chosen printer. The basic installation
can be considered complete if the print test is satisfactory. The AXIS
5570e/AXIS 5670e is now ready for use.
BCP and TBCP
You should specify if you want to enable or disable binary transfer of
print data in the print server’s web interface (Admin | Network
Settings | Detailed View | Macintosh | Binary Protocol for Printer
(1, 2). By enabling binary transfer you reduce printing time, provided
that the print job is sent as binary data to the print server. This is
particular true when you are printing large bitmaps.
•
•
•
TBCP enables the print server to use the TBCP (Tagged Binary
Communication Protocol) to transfer print data to the printer.
Select this alternative when using Postscript printers.
BCP enables the print server to use the BCP (Binary
Communications Protocol) to transfer print data to the printer.
Select this alternative when using Postscript printers.
None disables all binary transfers, select this alternative for all
non-PostScript printers and for ASCII PostScript printing.
Notes:
• If you have have set the Auto-Detect Printer Type parameter to YES, the text
output format will be chosen automatically (Admin | Network Settings |
Detailed View | Macintosh | Auto Detect Printer Type | Yes).
• Some printers, e.g. Epson InkJet printers, can not be used when TBCP is
enabled.
AXIS 5570e/AXIS 5670e User’s Manual
Setting Parameters
Section 8: Setting Up - Macintosh
In AppleTalk, you can change a limited number of the parameters of
the AXIS 5570e/AXIS 5670e. You can:
• enable and disable binary data transfers for your printing
• select the type of binary transfer protocol to use
• specify the AppleTalk printer type
• set the IP address
However, by assigning an IP address to your print server, you have
access to all of the print server parameters via any standard Web
browser or via FTP. Refer to Section 8 Print Server Management, on
page 85 for more information.
Example:
The following example describes how you set the print server
parameters in AppleTalk.
Important:
DO NOT use the parameter values from this example when configuring your
print server. You should select values that are appropriate for your printers and
network settings.
Follow the instructions below:
1. Open the Chooser from the Apple menu.
2. Select a network printer driver — any LaserWriter will do.
3. Select the printer port ending with _CFG.
4. Close the Chooser.
5. Open a text editor, e.g. SimpleText.
6. Write a text file containing the parameters you want to set:
BINARY_TYPE_1.
INT_ADDR.
ATYPE_1.
:BCP
:192.168.3.191
:EPSONLQ2
163
164
Section 8: Setting Up - Macintosh
AXIS 5570e/AXIS 5670e User’s Manual
Note:
Parameters that you do not want to set should be excluded from the text file.
Refer to the Parameter list in this manual for information about which values
that are valid for each parameter.
7. Print the text file. The settings will be stored in the print server.
8. Open the Chooser and select the printer port you wish to use for
printing documents.
9. Close the Chooser.
Note:
The _CFG port disappears 60 minutes after the AXIS 5570e/AXIS 5670e has
been powered on. If you want it to reappear, you must restart your print server.
AXIS 5570e/AXIS 5670e User’s Manual
Section 9
Section 9: Setting Up - UNIX
Setting Up - UNIX
Print Tools
For printer configuration, printtool and printconfig are the most
common. How they are invoked depends on which distribution and
window manager you use.
AIX
SMIT is the recommended printing tool. It contains an integrated
printer driver list, but does not have printer detection functionality.
Instructions:
Type the command smit in a Terminal window, then click Print
Spooling.
Debian
printtool is the recommended printing tool. The program contains an
integrated printer driver list, but does not have printer detection
functionality.
Instructions:
Type the command printtool in a Terminal window to start the
graphical version.
HP UX
Sam is the recommended printing tool. It doesn’t provide an
integrated printer driver list, nor printer detection functionality.
Instructions:
Type the command sam in a Terminal window, click Printers and
Plotters and then click Actions and Add_Remote Printer/Plotter.
Mandrake
printerdrake is the recommended printing tool. It contains an
integrated printer driver list, but does not have printer detection
ability.
165
166
Section 9: Setting Up - UNIX
Red Hat
AXIS 5570e/AXIS 5670e User’s Manual
printconf is the recommended printing tool. The program contains an
integrated printer driver list, but does not have printer detection
functionality.
Instructions:
Type the command printconf-gui in a Terminal window to start
the graphical version.
You can also run printconf as a text-based application if you do not
have the X Window System installed, or if you prefer the text-based
interface. Log in as root (or use the command su to temporarily
change to the root user), and type the command
/usr/sbin/printconf-tui from a shell prompt.
Solaris 9
The printing tool is called Printer Administrator. This operating
environment has an integrated printer driver list, but does not have
printer detection functionality.
Instructions:
Type the command /usr/sadm/admin/bin/printmgr in a
Terminal window.
SuSE
YaST2 is the recommended printing tool. It contains a printer driver
list as well as printer detection capability.
Instructions:
To start the Printer Configuration tool, select this from the Desktop:
YaST2 menu button (on the panel) | In Yast Control Center |
Hardware
| Edit Printers
AXIS 5570e/AXIS 5670e User’s Manual
Section 9: Setting Up - UNIX
Notes:
• A versatile IPP client for UNIX/Linux is CUPS. It can be downloaded from the
Common Unix Printing System’s Web site at www.cups.org
• If you don't find your specific printer in your distribution, have a look at
http://www.linuxprinting.org/database.html
Typical Invocation via a Windows Manager
Using the Mandrake 8.2 distribution (with CUPS installed) and the
KDE windows manger as an example, a typical set-up begins with
starting Mandrake Control Center.
1. Click Hardware | Printer and the Printerdrake application will be
invoked.
2. Click Expert Mode to be able to add a network printer.
3. Click the Add a new printer button.
Click Next.
Fill in data to help users identify the printer, i.e. name, description
and location. Click Next.
Select printer model and click Next.
Configure the printer and click Next.
The printer is set up. Click Finish and the printer is accessible.
Typical Invocation from a Terminal Window
Still using Mandrake as an example, open a Terminal Window and
type the command printtool. If you are in a terminal window, the
graphic version will start (as described above). If you do not have the
X Window System installed, the command will start a text based
167
168
Section 9: Setting Up - UNIX
AXIS 5570e/AXIS 5670e User’s Manual
version. The same information as was described above will be needed.
Note:
In Mandrake, even if you type printtool at a shell prompt,
will automatically start.
printerdrake
Debian 3.0
Debian offers a choice between plain LPD, LPRng and CUPS. There are
several printer configuration tools in this distribution, e.g. the
apsfilter (version 5 or later), which adds support for LPRng and
Ghostscript's uniprint driver scheme. Red Hat's printtool is also
supported, for those who prefer GUI administration tools.
For LPRng, LPD and CUPS use the Printtool.
Invocation
1. From the Gnome desktop, select Main Menu (on the panel) =>
Debian menus => Apps => System => Printtool.
2. On the KDE desktop, select the Main Menu (on the Panel) => System
=> Debian => Printtool.
3. Open a terminal window and type the command printtool (in
XTERM or Gnome).
Print Queues
Five types of print queues can be configured with printconf in the
Debian distribution:
•
•
•
•
•
Adding a Remote Unix
Printer
Local Printer
Unix Printer (lpd Spool
Windows Printer (SMB)
Novell Printer (NCP Queue)
JetDirect Printer
Start printtool and click Add.
Select Remote Unix (lpd) Queue from the Printer Type menu, and
click OK.
AXIS 5570e/AXIS 5670e User’s Manual
Section 9: Setting Up - UNIX
Text fields for the following options appears:
Printer name — Enter a unique name for the printer. (The name
cannot contain spaces and must begin with a letter. Valid characters
are a - z, A - Z, 0 - 9, -, and _.
Remote Host — The hostname or IP address of the remote machine
to which the printer is attached.
Remote Queue and input filter — The remote printer queue and
input filter.
Click Next to continue.
Click Select to choose a printer driver and to set it up.
Click OK.
Finally, click Test and print a test page.
Red Hat 7.3
Printtool has been replaced by Printconf. The utility maintains the
/etc/printcap configuration file, print spool directories, and print
filters.
Note:
Invocation
If you type printtool at a shell prompt, printconf will
automatically start.
1. On the Gnome desktop, select the Main Menu button (on the
Panel) => Programs => System => Printer Configuration to start
the graphical version.
2. On the KDE desktop, select the Main Menu button (on the Panel)
=> Red Hat => System => Printer Configuration to start the
graphical version.
3. Type the command printconf -gui at a shell prompt (for
example, in an XTerm or a Gnome terminal) to start the graphical
version.
169
170
Section 9: Setting Up - UNIX
AXIS 5570e/AXIS 5670e User’s Manual
4. You can also run printconf as a text based application if you do
not have the X Window System installed, or you just prefer the text
based interface. To run it, log in as root (or use the command su
to temporarily change to the root user), and type the command
/usr/sbin/printconf -tui from a shell prompt.
Print Queues
Five types of print queues can be configured with printconf in the
Red Hat distribution:
•
•
•
•
•
Local Printer
Unix Printer (lpd Spool)
Windows Printer (SMB)
Novell Printer (NCP Queue)
JetDirect Printer
Important!
• Do not edit the /etc/printcap file. Each time the printer deamon (lpd) is started
/restarted, a new /etc/printcap file is dynamically created.
• If you want to add a printer without using printconf, edit the
/etc/printcap.local file. The entries in /etc/printcap.local are not displayed in
printconf but are read by the printer daemon.
• If you upgrade your system from a previous version of Red Hat Linux, your
existing configuration file is converted to the new format used by printconf.
Each time a new configuration file is generated by printconf, the old file is
saved as /etc/printcap.old.
• If you add a new print queue or modify an existing one, you need to restart the
printer daemon (lpd) for the changes to take effect.
• Clicking the Apply button saves any changes that you have made and restarts
the printer daemon. The changes are not written to the /etc/printcap
configuration file until the printer daemon (lpd) is restarted. Alternatively, you
can choose File => Save Changes and then choose File => Restart lpd to save
your changes and then restart the printer daemon.
• If a printer appears in the main printer list with the Queue Type set to INVALID,
the printer configuration is missing options that are required for the printer to
function properly. To remove this printer from the list, select it from the list
and click the Delete button.
AXIS 5570e/AXIS 5670e User’s Manual
Adding a Remote
Unix Printer
Section 9: Setting Up - UNIX
To add a remote UNIX printer, such as one attached to a different
UNIX/Linux system on the same network, click the New button in the
main printconf window.
Select Unix Printer from the Queue Type menu, and click Next.
Enter a unique name for the printer in the Queue Name text field.
The printer name cannot contain spaces and must begin with a letter
a through z or A through Z. The valid characters are a through z, A
through Z, 0 through 9, -, and _. Click Next.
Text fields for the following options appear:
•
Server — The hostname or IP address of the remote machine to
which the printer is attached.
• Queue — The remote printer queue. The default printer queue is
usually lp.
By default, the Strict RFC1179 Compliance option is not chosen. If
you are having problems printing to a non-Linux lpd queue, choose
this option to disable enhanced LPRng printing features.
Click Next to continue
The next step is to select the type of printer that is connected to the
remote system.
Important!
The remote machine must be configured to allow the local machine to print
on the desired queue. As root, create the file /etc/hosts.lpd on the remote
machine to which the printer is attached. On separate lines in the file, add the
IP address or hostname of each machine which should have printing
privileges.
Selecting the Print
Driver
If you are configuring a local printer, select the print driver from the
list. The printers are divided by manufacturers. Click the arrow beside
the manufacturer for your printer. Find your printer from the
expanded list, and click the arrow beside the printer name. A list of
drivers for your printer will appear. Select one. Then finish the wizard
in the usual manner.
171
172
Section 9: Setting Up - UNIX
AXIS 5570e/AXIS 5670e User’s Manual
SuSE 8.0
The printing system on SuSE Linux is based on an apsfilter, with some
enhancements; SuSE's apsfilter will recognize all common file
formats (including HTML, if html2ps is installed).
There are two ways to setup printers on SuSE systems:
•
•
Invocation of YaST2
Print Queues
YaST2 will let you configure "PostScript", "DeskJet" and "Other
printers", supported by Ghostscript drivers; it's also possible to
setup HP's GDI printers (DeskJet 710/720, 820, 1000, via the
"ppa" package). YaST2 will provide /etc/printcap entries for every
printer ("raw", "ascii", "auto" and "color", if the printer to
configure is a color printer). YaST2 will create spool directories
and it will arrange apsfilterrc files, where you're able to fine tune
some settings (Ghostscript preloads, paper size, paper
orientation, resolution, printer escape sequences, etc.). With
YaST2 it's also possible to setup network printers (TCP/IP, Samba,
or Novell NetWare Printer).
SuSE includes the regular SETUP program from the original
apsfilter package (with some enhancements); run lprsetup to
invoke this configuration script. Once you get accustomed to its
GUI, you'll be able to configure local and network printers.
On the Gnome desktop select YaST2 Menu Button (on the panel) =>
Yast Control Center => Hardware => Edit Printers to start the Printer
Configuration tool.
On the KDE desktop select YaST Menu Button (on the panel) => Yast2
modules => Hardware => Edit printers to start the graphic version.
SuSE and YaST2 differ between these printer connections:
• Local printers (Parallel, USB, Serial and Disk File)
• LPD protocol network printing (Forward queue to a remote
LPD and Prefiltered queue for an LPD forwarding queue)
• Other network printing (Samba/Windows, Novell)
The SuSE installation manual explains the setup procedures in detail.
AXIS 5570e/AXIS 5670e User’s Manual
Section 9: Setting Up - UNIX
AXIS axinstall Script
Having performed the basic TCP/IP setup procedures as defined
earlier in this manual, you are now able to print in interactive mode
using PROS, LPR, FTP or Reverse Telnet protocols.
However, if you want to integrate the AXIS 5570e/AXIS 5670e with
your host spooler, you can use the Axis automatic installation script
axinstall. This utility software is resident in the print server and can
be downloaded to your host using FTP, so no disks are required. The
axinstall script is also available on www.axis.com
Having completed this operation, the printer connected to the print
server will appear as though it is directly connected to the host
printer spooler.
If you intend to use the print server in a multi-protocol environment,
refer to the chapters pertaining to the respective operating systems
in this manual.
Integration with the
Host Printer Spooler
To integrate the AXIS 5570e/AXIS 5670e with the host printer
spooler, you can use the auto installation script axinstall, resident in
the print server. Follow the instructions below to install axinstall
onto your host using FTP:
1. Login to the print server using the command:
ftp <host name>
-orftp <IP address>
2. Enter root as user id and pass as password.
3. Download the script using the command:
get axinstall
Log out using the command quit, bye or exit depending on your
173
174
Section 9: Setting Up - UNIX
AXIS 5570e/AXIS 5670e User’s Manual
FTP version.
> ftp npserver
connected to npserver.
220 AXIS 5570e/AXIS 5670e FTP Print Server v6.42
March 23 2003 ready.
Name (npsserver:thomas): root
331 User name ok, need password
Password: pass
(not visible)
230 User logged in
ftp> get axinstall
200 PORT command successful.
150 Opening data connection for axinstall
(192,36,253,4,13,223), (mode ascii).
226 Transfer complete.
local: axinstall remote: axinstall
61187 bytes received in 14 seconds (4.2 kbytes/s)
ftp> bye
221 Goodbye.
Typical FTP session for downloading the axinstall script
The axinstall script has now been downloaded to your host. Execute
the script with this command:
sh axinstall
or sh ./axinstall (depending on your system).
You will be guided through the installation by a step-by-step
procedure. During the installation you will be asked to select a print
method; we suggest you choose LPD or, for more functionality, use
the PROS filter or named pipe methods. Please refer to the following
pages if you need guidance on the choice of print methods.
AXIS 5570e/AXIS 5670e User’s Manual
Section 9: Setting Up - UNIX
Note:
NLPRng is not supported by axinstall.
The axinstall script will suggest one of the systems listed below when
started. If you do not find the suggestion appropriate, then manually
select any of the systems listed.
1....SunOS 4 (SUN BSD, Solaris 1.x)
2....SunOS 5 (SUN SYS V, Solaris 2.x)
3....AIX (IBM RS/6000, BULL DPX 20)
4....HP-UX (HP 9000)
5....BOS (BULL DPX 2)
6....DEC OSF/1 (Digital Equipment, Alpha)
7....ULTRIX (Digital Equipment, DEC)
8....IRIX (Silicon Graphics, SGI)
9....SCO UNIX (Santa Cruz Operation)
10...SCO UnixWare 2.x
11...SCO UnixWare 7
12...SCO OpenServer
13...FreeBSD (Berkeley UNIX)
14...Linux
15...Generic BSD (Berkeley UNIX)
16...Generic SYS V R3 (UNIX System V Release 3)
17...Generic SYS V R4 (UNIX System V Release 4)
Systems supported by axinstall
175
176
Section 9: Setting Up - UNIX
AXIS 5570e/AXIS 5670e User’s Manual
Print Methods on TCP/IP Networks
The AXIS 5570e/AXIS 5670e supports several different print methods
in the TCP/IP environment. axinstall will suggest a print method
suitable for your particular UNIX/Linux system, but you might want
to use another method depending on your printing requirements
(banner pages, status logging, etc).
The diagram below shows the alternative data paths taken by some
of the UNIX/Linux print methods. This illustrates some of the
advantages and limitations of the different methods. Use the
following information to determine which method to adopt.
Print
Spooler
File to
Print
Devices
Filter/
Interface
Model
Parallel Port
Named Pipe
DIRECT
FTP
RTELNET
Printer
LPD FTP
RTELNET PROS B
PROS print
daemon
PROS A
Axis Network Print Server
Illustration of different UNIX/Linux print methods
Directly
connected
printer
AXIS 5570e/AXIS 5670e User’s Manual
LPD
Section 9: Setting Up - UNIX
The Line Printer Daemon is a protocol for transferring print jobs
between hosts. This is the recommended method for UNIX/Linux
systems, but some System V versions do not support LPD.
Advantages:
Easy to set up — install the AXIS 5570e/AXIS 5670e as a remote
queue in System V, or add a remote printer to /etc/printcap
using the rm and rp fields (BSD).
Limitations:
Spooler features, and printcap or lpr options (BSD) such as
multiple copies, are not available.
FTP
The File Transfer Protocol is used for transferring files between hosts.
Advantages:
Uses industry standard network software on the host.
Limitations:
No printer status logging. In the case of BSD it may conflict
with other input or output filters and does not allow both input
and output filters. In System V no filters or interface programs
can be used.
177
178
Section 9: Setting Up - UNIX
PROS
PROS A
Advantages
PROS A
Limitations
AXIS 5570e/AXIS 5670e User’s Manual
A protocol developed at Axis. Comes in two versions;
named pipe (PROS A) and filter (PROS B).
The AXIS 5570e/AXIS 5670e appears as a device to the system. This
makes all filter and model options available. It provides accounting
and status logging. Supports bi-directional printing. The printer
information read back can be viewed in a log file.
A ‘C’ compiler is required to build the PROS A drivers.
Note:
You can download a ‘C’ compiler from http://www.gnu.org/.
PROS B
Advantages
It provides accounting and status logging. Supports bi-directional
printing. The printer information read back can be viewed in a log file.
PROS B
Limitations
A ‘C’ compiler is required to build the PROS B drivers and in the case
of BSD, it may conflict with other input or output filters. It does not
allow both input and output filters. Interface programs can not be
used in System V.
Reverse Telnet
Often used for printing via a terminal server printer port. Only
recommended if you already have a Reverse Telnet driver installed.
Advantages:
Easy to set up with previously installed Reverse Telnet drivers.
Limitations:
No status logging. Drivers are not supplied with the print server.
Existing drivers may be slow.
Other UNIX/Linux
Systems
Most UNIX/Linux systems resemble either BSD or System V and so
with some ingenuity, a solution can also be devised for other
variants.
If the system has BSD socket type networking support, then prosbsd
(in the bsd directory of the AXIS 5570e/AXIS 5670e) can be used as a
starting point. It receives print data from stdin, and writes a log file
to stderr. Nothing is written to stdout.
AXIS 5570e/AXIS 5670e User’s Manual
Section 9: Setting Up - UNIX
Alternatively, FTP may be used. It is a good idea to use bsd/ftp_bsd
or sysv/ftp_sysv as a starting point.
IBM MVS Systems
A sample JCL script, jclex, is available in the mvs directory of the
print server. It gives an example of how to print a file from an MVS
mainframe to an AXIS 5570e/AXIS 5670e using FTP.
179
180
Section 10: Management and Configuration
Section 10
AXIS 5570e/AXIS 5670e User’s Manual
Management and Configuration
The management and configuration tools that are supported by the
AXIS 5570e/AXIS 5670e allow you to:
Configuration
Overview
•
Change the print server parameters, i.e. editing the config file
•
Receive extended information about the print jobs
•
Receive printer port status
•
Monitor your printers
•
Reset the AXIS 5570e/AXIS 5670e
The method you should use to manage and configure your AXIS
5570e/AXIS 5670e depends on the operating system protocols of
your network. The table below displays which method to use for each
supported environment.
Operating System Protocols
Configuration/Management methods
IBM Host
(AS/400, IBM Mainframe)
From an IBM Host - See page 203
TCP/IP
(AS/400, IBM Mainframe, UNIX,
Windows
Web Browser - See page 181
AXIS ThinWizard - See page 189
FTP - See page 192
Telnet - See page 195
SNMP - See page 199
IPX/SPX
(NetWare)
Novell Utilities - See page 201
NetBIOS/NetBEUI
Windows
Web Browser - See page 181
AppleTalk
Web browser - See page 181
Mac-FTP - See page 192
AXIS 5570e/AXIS 5670e User’s Manual
Section 10: Management and Configuration
Using a Web browser
Once you have established the AXIS 5570e/AXIS 5670e in the TCP/IP
environment, as described in Setting the IP address, on page 24, you
are free to access the AXIS 5570e/AXIS 5670e Web pages from any
standard Web browser.
The Web interface of the AXIS 5570e/AXIS 5670e is divided into two
modes of operation, User mode and Admin mode.
User
In User mode, you have no rights to change any parameter settings.
However, if you have access rights to the Admin mode, you can
change some of the basic parameters from User mode via the
Configuration Wizard. This mode is intended for regular users who
are only interested in using the print server's interface for checking
print jobs or viewing printer properties. If you want to change any
other of the print server's settings, you must enter the Admin mode.
Admin
When in Admin mode, you have access to all the print server's
parameters and you can change them to your liking. This mode is
intended for network administrators and can be password protected
to prevent unauthorized changing of the print server parameters.
Note:
To protect the Admin pages from unauthorized use, enter a password in the Root
Password field under Admin | General Settings
181
182
Section 10: Management and Configuration
Accessing the Web
Pages
AXIS 5570e/AXIS 5670e User’s Manual
Follow the steps below to access the internal web pages of the AXIS
5570e/AXIS 5670e:
1. Enter the print server’s IP address (or host name) in the
Location/Address field of your Web browser. Press Enter
2. The Printer Overview page will appear. Click the admin button
to access the Administration web pages.
3. You will be prompted for a password, enter the default user
name root and the default password pass. Click OK.
Note:
•
It is highly recommended that you change the default password. This is done
from the Admin | General Settings | General tab in the Root Password field
•
You can address the print server’s Web interface via https:// To do this you must
enable the SSL/TLS protocols in the web interface: Admin | Network Settings |
Detailed View| TCP/IP and set the HTTPS Enabled parameter to Yes (you must
have a valid certificate loaded).If you do not have a valid certificate loaded,
select Admin | Security Settings and click Create.
root
pass
AXIS 5570e/AXIS 5670e User’s Manual
Section 10: Management and Configuration
Available Services
from the User Mode
The following services are available from the User mode. A link to the
Axis home page is available from this mode.
Printer Overview
The Printer Overview page contains a section that allows you to view
the general parameter setting of the AXIS 5570e/AXIS 5670e,
including the print server name and the location of the print server in
your organization, if defined.
If you have admin access rights you can use the Configuration
Wizard for general settings to perform basic configuration of the
AXIS 5570e/AXIS 5670e and the Configuration Wizard for IBM
sessions to add an IBM session.
By clicking the printer icon a printer page opens, allowing you to view
the status and the supported capabilities ofconnected printer. The
extent of this information depends on the printer model. From the
printer page, you can also print a test page to the printer.
Print Jobs
From the Print Jobs page you can view the status of the current print
jobs, including the number of printed bytes and the origin of the print
job. You can also view a log of the 20 latest print jobs that includes
the user, the printing protocol and the file size. A log that displays
the accumulated usage of the connected printers allows you to
control the usage of the connected printers.
Help
The Help page presents you with basic information about the AXIS
5570e/AXIS 5670e and the Web user interface. A short description of
the Axis installation tools you should use when installing a printer on
your PC, is also included.
183
184
Section 10: Management and Configuration
Available Services from
the Admin Mode
This Print Server
AXIS 5570e/AXIS 5670e User’s Manual
The following services are available from the Admin mode. An
additional link to www.axis.com is available from this mode.
The This Print Server page contains a section that allows you to view
and modify the general parameter setting of the AXIS 5570e/AXIS
5670e, including the print server name, the node address, the
password and the base URL. You can also configure any of the eight
logical printers of the AXIS 5570e/AXIS 5670e. Management
operations, like restarting the AXIS 5570e/AXIS 5670e and resetting
its parameters to the factory default settings, are also available.
Caution!
Any network configuration should involve the Network Administrator.
By clicking on the printer icon, a printer page opens, allowing you to
view the status and the supported capabilities of connected printer.
The extent of this information is depending on the printer model.
From the printer page, you can also print a test page to the printer.
AXIS 5570e/AXIS 5670e User’s Manual
Section 10: Management and Configuration
Print Jobs
From the Print Jobs page you can view the status of the current print
jobs, including the number of printed bytes and the origin of the print
job. You can also view a log of the 20 latest print jobs that includes
the user, the printing protocol and the file size. A log that displays
the accumulated usage of the connected printers allows you to
control the usage of the connected printers. If you want to delete an
ongoing print job, a delete button is available on this page.
IBM Sessions
From the IBM sessions page you can view the list of configured IBM
sessions. You can choose to edit or delete a session from the list or
add a new session from the Add Session button.
IBM Emulators
The IBM Emulators page contains three Detailed View buttons.
•
SCS/IPDS emulator configurations. Select the IBM printer that is
to be emulated from the drop-down list.
•
SCS/3270DS emulator configurations
Common emulator settings: page format, CPI mapping, job control, 3270 options, extended emulation, user driver.
•
IPDS emulator configurations
IPDS Emulator Settings: IPDS configuration, IPDS PostScript
Driver settings, IPDS PCL Driver settings
185
186
Section 10: Management and Configuration
Network Settings
AXIS 5570e/AXIS 5670e User’s Manual
From the Network Settings page you can set all parameters that
control the network traffic to and from the AXIS 5570e/AXIS 5670e.
You can enable or disable any of the supported network protocols
and fine-tune the parameter settings.
Admin | Network Settings | Detailed View | TCP/IP
If you want to set a static IP address, make sure
you first set DHCP, RARP, BOOTP and Auto-IP Enabled
to No.
Support
From the Support page you can receive help to resolve any
installation or print problems that might occur. If your problems
persist, the Support page allows you to produce a Server Report. The
Server Report includes the settings of the AXIS 5570e/AXIS 5670e,
information about your connected printers as well as the current
network settings. The Server Report is of great value for support
assistance, so please mail, email or fax it to your support channel
together with a detailed problem description.
AXIS 5570e/AXIS 5670e User’s Manual
Section 10: Management and Configuration
Statistics
The Statistics page displays information about the network traffic to
and from the AXIS 5570e/AXIS 5670e as well as information about
servers and services that are connected or associated with the AXIS
5570e/AXIS 5670e.
Help
The Help page displays a comprehensive description of the
configuration and management activities that can be performed from
the internal Web pages of the AXIS 5570e/AXIS 5670e. Theses
activities include instructions on how to install the AXIS 5570e/AXIS
5670e in various environments and how to upgrade it with new
firmware. A detailed index is also available.
Security Settings
On the Security Settings page you can enable or disable SSL (Secure
Socket Layer - a protocol designed to provide secure communications
on the Internet.) and TLS (Transport Layer Security, a protocol that
guarantees privacy and data integrity between applications
communicating over the Internet) You can also create secure
certificates and disable/enable insecure protocols.
Whenever SSL/TLS is enabled, you have to address the print server’s
Web interface in the secure way, i.e. via https://
See Enabling Secure Web Services — SSL/TLS, on page 122 for a
detailed description.
Parameter List
Restart
Shows all print server parameters and their current settings.
Restarts the print server.
187
188
Section 10: Management and Configuration
Software Default
AXIS 5570e/AXIS 5670e User’s Manual
A Software Default will reset all print server parameters and settings
to their default values except:
• Node address (NODE_ADDR.)
• IP Address (INT_ADDR.)
• DHCP enabled (DHCP_ENB)
• Installed certificate
• Private key
A Software Default differs from a Factory Default in that the latter is
done by pressing the test button in a specific sequence to
default/clear all print server parameters to default.
See The Test Button, on page 132 for instructions on performing a
Factory Default.
Firmware Upgrade
Upgrades the print server’s internal software.
AXIS 5570e/AXIS 5670e User’s Manual
Section 10: Management and Configuration
Using AXIS ThinWizard for Print Server Management
AXIS ThinWizard software allows you to manage and upgrade
multiple Axis products. Using a standard Web browser, you can find,
install, monitor, configure and upgrade your Axis print servers
remotely in any TCP/IP network. AXIS Thin Wizard 3.0 is Windows
2000 and Windows XP compatible.
Installing AXIS
ThinWizard
AXIS ThinWizard software is available on www.axis.com
You should only install AXIS ThinWizard on a designated computer on
your network.
To install, follow the instructions given by the Installation Wizard.
During the installation, you will be asked to enter a user id and a
password — these will be used when logging in to AXIS ThinWizard,
so please take a note of them.
Important:
Starting AXIS
ThinWizard
•
To use all AXIS ThinWizard features, the print server must have the
FTP_ENB. parameter set to “Yes”. This is done in the print server’s web
interface: Admin | Network Settings | Detailed view | TCP/IP
•
If you disable SNMP in the Print server’s web interface, you will disable
AXIS ThinWizard’s ability to determine print server status!
Enabling/Disabling SNMP is done from Admin | Network Settings |
Detailed view | SNMP
Follow the instructions below to start AXIS ThinWizard:
1. Make sure that the computer where you installed the AXIS
ThinWizard is up and running on your network.
2. Start a Web browser on a client in your network.
3. Enter the IP address or the host name of the computer where you
installed AXIS ThinWizard. (If the server is installed on another port
than 80, you must enter the port name after the host name or the
IP address).
189
190
Section 10: Management and Configuration
AXIS 5570e/AXIS 5670e User’s Manual
4. The AXIS ThinWizard start page now appears in the Web browser.
Enter the user id and password you specified during installation and
click Log in.
5. The AXIS ThinWizard interface appears:
The first time you use AXIS ThinWizard, set the Preferences to reflect
your network environment:
Select a network group from the list on the Manage Network page. If
the list is empty, you must first create a group. Click the Network
Groups tab and follow the instructions.
Creating a
Network Group in
AXIS ThinWizard
The network group concept is the corner stone of AXIS ThinWizard.
By dividing your network into network groups, you can monitor your
print servers more efficiently. The scope of each network group is
determined by the Axis server types and IP address ranges that are
included. You can create as many network groups as you want.
Follow the instructions below to create a network group:
1. Click Network Groups in the AXIS ThinWizard main menu.
2. Click Create.
AXIS 5570e/AXIS 5670e User’s Manual
Section 10: Management and Configuration
3. The Create Network Group page opens. Type the name of the
network group, enter the IP address ranges and Axis server types
that should be included. If you are only interested in managing print
servers, deselect all options but the print server option.
4. Click OK to create the network group.
You can edit the properties of each network group from the Network
Groups page. Simply select the network group from the list and use
one of the Edit, Copy or Remove commands.
Managing
Print Servers
Follow the instructions below to access the AXIS 5570e/AXIS 5670e
using AXIS ThinWizard:
1. Click Manage Network in the main menu.
2. Select the network group, including the, from the drop-down list.
All AXIS servers included in the network group appear in the
window.
3. Click the link of the AXIS 5570e/AXIS 5670e to access its internal
Web page.
4. The ‘Srv’ and ‘Dev’ columns show the status of your print servers
and printers.
You are now free to manage and configure the print server as
described in Available Services from the User Mode, on page 183.
Upgrading
Axis Servers
Refer to Upgrading using AXIS ThinWizard, on page 128, for more
information about upgrading Axis servers using AXIS ThinWizard.
Additional
Information
If you need more information, please refer to the AXIS ThinWizard
on-line help.
191
192
Section 10: Management and Configuration
AXIS 5570e/AXIS 5670e User’s Manual
Using FTP for Print Server Management
Having assigned an IP address to your AXIS 5570e/AXIS 5670e, as
described in Setting the IP address, on page 24, you can change the
AXIS 5570e/AXIS 5670e parameter settings using the File Transport
Protocol (FTP).
Editing the config file
Follow the instructions below to edit the config file using FTP:
1. Log in to the AXIS 5570e/AXIS 5670e by typing:
ftp <host name> or ftp <IP address> in a DOS window
(Windows and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root
and pass.)
3. Download the config file to your host by typing:
get config
4. Edit the file using your preferred text editor.
5. Save the config file to the AXIS 5570e/AXIS 5670e by typing:
put config CONFIG
Notes:
•
It is important that the destination file is specified in capital letters.
Otherwise the edits are temporary and will be lost once the AXIS
5570e/AXIS 5670e has been powered off.
•
To edit the config file from a Macintosh you will need FTP support such as
MacTCP, Fetch or Anarchie. The procedure for editing the file is the same as
described above.
The example on the next page describes how to edit the config file
using FTP from a DOS window.
AXIS 5570e/AXIS 5670e User’s Manual
Section 10: Management and Configuration
Example:
> ftp npserver
connected to npserver.
220 AXIS 5570e/AXIS 5670e FTP Print Server v6.30 Dec
16 2000 ready.
Name (npserver:thomas): root
331 User name ok, need password
Password: pass
(not visible)
230 User logged in
ftp> get config
200 PORT command successful.
150 Opening data connection for config
(192,36,253,4,13,223), (mode ascii).
226 Transfer complete.
8588 bytes received in 0.24 seconds (35.63 kbytes/s)
ftp> put config CONFIG
200 PORT command successful.
150 Opening data connection for CONFIG
(192,36,253,4,13,223), (mode ascii).
226 Transfer complete.
8588 bytes received in 0.45 seconds (19.04 kbytes/s)
ftp> bye
221 Goodbye.
>
193
194
Section 10: Management and Configuration
Viewing
the Account File
AXIS 5570e/AXIS 5670e User’s Manual
The account file contains data concerning the ten last print jobs. It
specifies an internal job number, the user that initiated the job, the
protocol and logical printer that was used, current status (Completed,
Off-line, or Printing), number of bytes printed, elapsed time and offline time.
Follow the instructions below to view the account file using FTP:
1. Log in to the AXIS 5570e/AXIS 5670e by typing:
ftp <host name> or ftp <IP address> in a DOS windows
(Windows and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root
and pass.)
3. Download the account file to your host by typing:
get account
4. View the account file using your preferred text editor.
Viewing
the Status File
The status command shows which printer port the logical printers are
assigned to, and their current status.
Follow the instructions below to view the status file using FTP:
1. Log in to the AXIS 5570e/AXIS 5670e by typing:
ftp <host name> or ftp <IP address> in a DOS windows
(Windows and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root
and pass.)
3. Download the status file to your host by typing:
get status
4. View the status file using your preferred text editor.
FTP Help
By typing help in step 3 in the FTP instruction sets above, a list of all
available files and commands will be displayed.
AXIS 5570e/AXIS 5670e User’s Manual
Section 10: Management and Configuration
Using Telnet
Having assigned an IP address to your AXIS 5570e/AXIS 5670e, as
described in Setting the IP address, on page 24, you can manage your
AXIS 5570e/AXIS 5670e using the Telnet protocol.
Viewing
the Account File
The account file contains data concerning the last ten print jobs. It
specifies an internal job number, the user that initiated the job, the
protocol and logical printer that was used, current status (Completed,
Off-line, or Printing), number of bytes printed, elapsed time and offline time.
Follow the instructions below to view the account file using telnet:
1. Log in to the AXIS 5570e/AXIS 5670e by typing:
telnet <host name> or telnet <IP address> in a DOS
window (Windows and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root
and pass.)
3. View the account file by typing:
account
The example on the next page shows how to view the account file
using Telnet from a UNIX shell.
195
196
Section 10: Management and Configuration
AXIS 5570e/AXIS 5670e User’s Manual
Example:
> telnet npserver
Trying 192.36.253.96...
Connected to npserver.
Escape character is ‘^]’.
AXIS 5570e/AXIS 5670e TELNET Print Server v6.30 Dec
16 2000
AXIS 5570e/AXIS 5670e network login: root
Password: pass
(not visible)
AXIS 5570e/AXIS 5670e TELNET Print Server v6.30 Dec
16 2000
Root> account
Current account file:
JOB
USER
PROT
LPR S BYTES ETIME OTIME
1
Thomas
FTP
pr2 C 1885
2
Joe
LPT
pr1 C 23074 4
0
3
RICHARD
PSERVER
pr2 C 43044 5
0
4
MacUser
APPLE
2
0
5
LSLM_userNetBIOS
pr2 C 36995 3
0
6
patrick
pr5 P 83208 9
0
PROS
pr1 C 6717
Root>
Typical Telnet session to view the Account File
2
0
AXIS 5570e/AXIS 5670e User’s Manual
Viewing
the Status file
Section 10: Management and Configuration
The status command shows which printer port the logical printers are
assigned to, and their current status.
Follow the instructions below to view the status file using telnet:
1. Log in to the AXIS 5570e/AXIS 5670e by typing:
telnet <host name> or telnet <IP address> in a DOS
window (Windows and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root
and pass.)
3. View the status file by typing:
status
Performing resets
Three types of reset commands allow you to perform soft resets, to
perform hard resets, and to reset the print server’s parameters to its
default settings.
Follow the instructions below to perform a soft reset using telnet:
1. Log in to the AXIS 5570e/AXIS 5670e by typing:
telnet <host name> or telnet <IP address> in a DOS
window (Windows and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root
and pass.)
3. Restart the print server’s protocols by typing:
softreset
Replace the command in step 3 above with hardreset or default
to perform the other two reset operations.
Printing Hexdumps
The AXIS 5570e/AXIS 5670e allows you to record a trace of the
communication between the AXIS 5570e/AXIS 5670e and the host.
The AXIS 5570e/AXIS 5670e supports hexdump printing for the SNA,
TN3270E, TN5250E, LPR/LPD and Raw TCP/IP printing protocols.
Please refer to Product Model Summary, on page 9 for details on the
supported protocols.
197
198
Section 10: Management and Configuration
AXIS 5570e/AXIS 5670e User’s Manual
Follow the instructions below to perform a hexdump printout for the
SNA printing protocol:
1. Log in to the AXIS 5570e/AXIS 5670e by typing:
telnet <host name> or telnet <IP address> in a DOS
windows (Windows and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root
and pass.)
3. Enable the AXIS 5570e/AXIS 5670e to hexdump mode by typing:
snahexdump
4. Select Start Logging from the Terminal menu in the Telnet
window. Specify a file name and select the folder where you
want to save the file.
5. Start the print job.
6. When the print job is finished, select Stop Logging from the
Terminal menu.
7. Enter the quit command
Replace the command in step 3 above with tnehexdump for the
TN3270E and TN5250E protocols, lpdhexdump for the LPR/LPD
protocol, or rtnhexdump for the reverse Telnet protocol.
Telnet Help
By typing help in step 3 in any of the Telnet instruction sets above, a
list of all available commands will be displayed.
AXIS 5570e/AXIS 5670e User’s Manual
Section 10: Management and Configuration
Using SNMP
You can use SNMP (Simple Network Management Protocol) for
remotely monitoring and configuring of the AXIS 5570e/AXIS 5670e.
All major functions for print servers are supported.
General Information
SNMP refers to a set of standards for network management,
including a protocol, a database structure specification, and a set of
data objects. The AXIS 5570e/AXIS 5670e SNMP implementation runs
in the TCP/IP environment.
The management is handled by NMS (Network Management System)
software running on a host on your network. The NMS software
communicates with network devices by the means of messages,
which are references to one or more objects.
A message can be a question or an instruction to a device, or an
alarm triggered by a specific event in a device. Objects are contained
in data bases called MIBs (Management Information Base), where
MIB-II is a standard database.
The AXIS 5570e/AXIS 5670e supports all relevant parts of MIB-II and
also includes a private enterprise MIB. Refer to The AXIS MIB, on
page 200.
System Requirements
for SNMP
The following requirements must be fulfilled in order to make full use
of the AXIS 5570e/AXIS 5670e SNMP support:
•
NMS software that allows you to install private enterprise MIBs
•
A host, supporting FTP, on which to run the NMS software
Follow these steps to add the AXIS MIB to your NMS software:
1. Log in to the AXIS 5570e/AXIS 5670e using FTP.
2. Download the MIB file /snmp/axis.mib to the NMS host.
3. Install the AXIS MIB according to instructions in your NMS
software documentation.
199
200
Section 10: Management and Configuration
The AXIS MIB
AXIS 5570e/AXIS 5670e User’s Manual
The AXIS MIB contains a large number of objects which may be
categorized as follows:
•
Menu objects - used for viewing and changing the AXIS
5570e/AXIS 5670e configuration from the NMS program. Refer
to The Parameter List, on page 295.
•
Printer status and unit administration objects - used for monitoring AXIS 5570e/AXIS 5670e print jobs and storing parameter
changes permanently.
•
Trap objects - used for alarms at various error conditions.
For technical details, you can view the MIB file (axis.mib) with any
text editor.
AXIS 5570e/AXIS 5670e User’s Manual
Section 10: Management and Configuration
Using Novell Utilities
After installing the AXIS 5570e/AXIS 5670e into the NetWare
environment, you can manage your AXIS 5570e/AXIS 5670e, using
either Novell’s NetWare Administrator, or PCONSOLE.
NetWare
Administration
Printer Status
Some useful features provided by the NetWare Administrator are
described in more detail below:
The Printer Status menu, detailed below, shows the status of an
active print job serviced by an AXIS 5570e/AXIS 5670e network print
server. It displays detailed information concerning the active job
including, Print Queue, print job description, size of print file,
percentage of job completed, etc. You can also abort or pause the
print job from this menu.
NetWare Administrator Printer Status Menu
201
202
Section 10: Management and Configuration
AXIS 5570e/AXIS 5670e User’s Manual
Notification
You can use the NetWare Administrator to enable or disable status
notification messages for printers connected to the AXIS 5570e/AXIS
5670e, e.g. Busy, Off-line, Out of paper, Paper jam, etc. You can also
add or remove print job owners and administrators from the list of
persons to be notified.
Print Layout
You can view installed AXIS 5570e/AXIS 5670e Network Print Servers
and their relative print queues for any NetWare Organizational Unit.
You can also display summary information by right-clicking on the
printer object you want to examine.
NetWare Print Layout with corresponding information summary
AXIS 5570e/AXIS 5670e User’s Manual
Section 10: Management and Configuration
Configuring the Print Server from an IBM host
Once communication with an IBM host has been established, all the
AXIS 5570e/AXIS 5670e parameters can be edited by printing a file
containing special configuration commands. To start the
configuration, the command %CONFIG+ is entered in the file. To
protect your settings, a password must be provided. By default, the
password is pass. When all parameters are set, the command SAVE is
used to store the parameters permanently. The command %CONFIGleaves the configuration mode and resumes normal printing. The
syntax for the file to print is:
%CONFIG+ <password;>
IBM_PRINTING_PARAMETER_NAME = VALUE;
SAVE;
%CONFIG-
In order to maintain backward compatibility and increase security,
many parameters that are not related to the IBM printing operation
have to be preceded by the %CONFIG++ command. When all
parameters are set, enter %CONFIG--. The parameters requiring
%CONFIG++ are clearly marked in the parameter listing on the
following pages.
%CONFIG+ <password;>
IBM_PRINTING_PARAMETER_NAME = VALUE;
%CONFIG++
PARAMETER_NAME = VALUE;
%CONFIG-SAVE;
%CONFIG-
203
204
Section 10: Management and Configuration
AXIS 5570e/AXIS 5670e User’s Manual
Select the PCL5 printer driver and disable the NetWare protocol:
%CONFIG+ password;
PRDRIVER = PCL5;
%CONFIG++
NETW_ENB = NO;
%CONFIG-SAVE;
%CONFIG-
(If you have not changed the default
password (pass), the password is optional)
For parameters requiring more than one value, the values should be separated
using a comma.
AXIS 5570e/AXIS 5670e User’s Manual
Section 11
Section 11: Configuration Possibilities
Configuration Possibilities
This section describes some special features offered by the AXIS
5570e/AXIS 5670e:
Autodetect Printer Type, on page 205
AutoIP, on page 206
E-mail Notification, on page 206
Flash Loading of Firmware over the Web, on page 230
IPP (Internet Printing Protocol), on page 207
Logical Printers for Customized Printing, on page 220
Network Speed, on page 230
NetWare Packet Signature Level 1,2,3, on page 230
Secure Web Services — SSL/TLS, on page 231
Autodetect Printer Type
The print server can automatically detect the type of printer you are
using if you enable Autodetect Printer Type. The print server can
then recognize Epson and Hewlett Packard InkJet printers. Most
Epson and Hewlett Packard InkJet printers that have Mac OS printer
drivers for network printing are supported. If Autodetect Printer
Type is disabled, the AppleTalk printer type has to be specified
manually in the print server. For Epson InkJets it would be
"EPSONLQ2" and for HP InkJets it would be "DeskWriter". If the print
server does not recognize the connected printer the default setting,
"LaserWriter" will be used as printer type. "LaserWriter" is the
recommended setting to be used with all PostScript printers.
To enable Autodetect Printer Type, log in to your print server’s Web
interface and select Admin | Network Settings | Detailed View |
Macintosh | Auto Detect Printer Type | Yes.
See the Help pages in the print server’s Web interface for details.
205
206
Section 11: Configuration Possibilities
AXIS 5570e/AXIS 5670e User’s Manual
AutoIP
In the absence of an IP address management mechanism such as
DHCP, the print server will receive a temporary IP address
automatically over AutoIP, a method which enables the host to
automatically take a linklocal IPv4 address. AutoIP is supported by
Windows 98, Me, 2000, XP and Mac OS version 8.5 or higher.
See “Dynamic IP Address Assignment” on page 24
E-mail Notification
Whenever an event that needs human intervention occurs in a
network printer, the concerned person can be notified by e-mail. This
’trouble-report’ contains a short and concise description of the event.
Five events are covered: Paper Jam, Out of Paper, Toner Low, No
Toner, Printer Off-line.
In order to determine who the e-mail recipients will be of these
different trouble-reports, follow these instructions:
1. From your print server’s internal web page, go to: Admin |
Network Settings | Detailed View | e-mail Notification. The
following options will appear:
Options
PAPER JAM
OUT OF PAPER
TONER LOW
NO TONER
PRINTER OFFLINE
E-mail recipient
The person responsible for handling paper jams in the
printer
The person responsible for filling the printer with paper
The person responsible for filling up the toner in the
printer
The person responsible for changing the toner in the
printer
The person responsible for the overall maintenance of
printer
2. Enter the respective e-mail addresses of the trouble-report
recipients in the blank fields as follows:
[email protected]
AXIS 5570e/AXIS 5670e User’s Manual
Section 11: Configuration Possibilities
3. Click OK and exit when done.
Important:
Check that the SMTP Server and Domain Name parameters in the print server’s internal web
pages are correct. This is done in: Admin | Network Settings | Detailed view | TCP/IP
IPP (Internet Printing Protocol)
Printing over the Internet with IPP (Internet Printing Protocol) is
possible with the AXIS 5570e/AXIS 5670e. IPP is an industry standard
that allows users to print to remote printers across the Internet.
With IPP, a user with an Internet connection can send a document to
any printer which is connected to the Internet. IPP is platform
independent and can be used to print over any LAN or WAN that
supports TCP/IP.
In practical terms, this means that you can send documents to a
remote printer as an addition to or replacement of fax and e-mail,
with the same quality and color options of traditional network
printing.
In order to print to a remote printer using IPP, you need the
following:
• An IPP client installed on your computer together with appropriate printer drivers. The IPP client is a tool that adds destination
printers to your printer list. A list of available IPP clients can be
viewed in IPP clients, on page 209.
• The printer to which you want to send your print job needs to be
connected to a print server with IPP functionality. The print
server makes it possible for your printer to receive print jobs from
an IPP client. The IPP functionality of the AXIS 5570e/AXIS 5670e
is automatically activated upon installation.
207
208
Section 11: Configuration Possibilities
IPP Printing
Requirements
AXIS 5570e/AXIS 5670e User’s Manual
Before you print to an IPP printer you need to know:
• the http:// address of the print server.
• the brand and model of the printer in order to install the appropriate printer driver.
Address Schemes for
IPP Printers
When using IPP printing, you need to know the IP address or host
name of your IPP enabled Axis print server. IPP is a client/server type
protocol which comprises two industry standards:
• the 1.0 standard, which uses an http:// address scheme
• the 1.1 standard, which uses an ipp:// address scheme
Example using a
Host Name
in the 1.0 Standard:
If “axisps” is the host name of the AXIS 5570e/AXIS 5670e, "631" is
the port number and "USB1" is the local printer port name, then the
syntax of the address scheme will be http://axisps:631/USB1 in
the 1.0 standard.
Example using an
IP Address
in the 1.1 Standard:
If “171.16.5.218” is the IP address of the AXIS 5570e/AXIS 5670e and
"USB1" is the local printer port name, then the syntax of the address
scheme will be ipp://171.16.5.218/USB1 in the 1.1 standard.
AXIS 5570e/AXIS 5670e User’s Manual
IPP clients
Section 11: Configuration Possibilities
An IPP client needs to be installed on your computer together with an
appropriate printer driver for proper IPP functionality. The IPP client
is a tool that adds destination printers to your printer list.
The AXIS 5570e/AXIS 5670e with integrated IPP is compatible with
any 1.0 and 1.1 compliant IPP client.
The AXIS 5570e/AXIS 5670e presents IPP printer objects to the client,
one for each printer port. Some of the most common IPP client
printing methods are described later on in this chapter. Please refer
to your IPP client documentation for more specific information.
Currently Available IPP
Clients on the Market:
• For Windows NT/2000: the Internet Printer Connection software
from Hewlett Packard (can be downloaded from the Hewlett
Packard Web site).
• For Windows 2000/XP: the Microsoft IPP Client (automatically
installed with the Operating System).
• For Windows 98, NT 4.0: IPP clients can be downloaded from the
Microsoft Web site.
• For UNIX/Linux: CUPS (can be downloaded from the Common
Unix Printing System Web site at www.cups.org).
If you wish to print using iPrint over IPP, the following Axis snap-in
tool is available from www.axis.com/techsup => Select Software:
• AXIS IPP Gateway Comfiguration Snap-in for i-Print in
NetWare 5.x. See the read-me file for installation
instructions.
IPP User Requirements
The IPP protocol does not require any special configuration of the
AXIS 5570e/AXIS 5670e, the IPP function is automatically activated
when you install your print server.
IPP is platform independent and functional in Windows (NT, 98, Me
and 2000/XP), Macintosh, NetWare and UNIX/Linux.
209
210
Section 11: Configuration Possibilities
Firewall
Considerations with
IPP
How to Print from
Windows 98:
AXIS 5570e/AXIS 5670e User’s Manual
If there are one or more firewalls between the IPP client and the
server, you may have to make some changes to the firewall
configuration. IPP uses TCP Port 631 for printing, so any firewalls
between client and server must be configured to allow bi-directional
traffic on that port. Please consult your network administrator if you
think any configuration changes are necessary.
Before you print to an IPP printer you will need to know:
• the http:// address of the print server. The http:// address contains the IP address or host name of the print server and the
printer port name.
• the brand and type of the printer in order to install the appropriate printer driver.
If your destination printer does not exist in your Printer name list,
you need to add it. Adding an IPP printer to your printer list is
described below.
1. Select the IPP printer to which you want to send your document.
Choose the destination printer from the Printer name field (in
File | Print).
2. When you press Print, the print job is sent over the Internet to
the AXIS 5570e/AXIS 5670e, which then forwards the print job to
the destination printer.
3. The recipient of the print job can collect the print job at the
destination printer.
Adding an IPP Printer
to your Printer List in
Windows 98
1. Install the IPP client for Windows 98 on your computer. This IPP
client can be downloaded from the Microsoft Web site.
2. Open Start | Settings | Printers.
3. Choose Add Printer, then Network Printer.
4. In the Printer field in the Connect to Printers window, write the
http:// address of the destination printer.
(Example: http://171.16.5.218:631/USB1)
AXIS 5570e/AXIS 5670e User’s Manual
Section 11: Configuration Possibilities
5. Select the appropriate printer driver corresponding to the
destination printer.
6. Specify a name for the printer you wish to add to your printer
list. Click Finish. The destination printer will be added to your
printer list and you are ready to print using IPP.
How to Print from
Windows NT:
Before you print to an IPP printer you will need to know:
• the http:// address of the print server. The http:// address contains the IP address or host name of the print server and the
printer port name.
• the brand and type of the printer in order to install the appropriate printer driver.
1. First you need to select the IPP printer to which you want to send
your document. Select the destination printer from your Printer
Name list (in File | Print | Printer Setup).
The printer name will begin with a URL: http://...
If your destination printer does not exist in your Printer Name list,
you need to add it. Adding an IPP printer to your printer list is
described below.
2. When you press Print, the print job is sent over the Internet/WAN
to the AXIS 5570e/AXIS 5670e, which then forwards the print job
to the destination printer.
3. The recipient of the print job can collect the print job at the
destination printer.
211
212
Section 11: Configuration Possibilities
Adding an IPP Printer
to your Printer List in
Windows NT
AXIS 5570e/AXIS 5670e User’s Manual
1. Install the Internet Printer Connection software from Hewlett
Packard (can be downloaded from the Hewlett Packard Web site)
on your computer.
2. Open Start | Settings | Printers.
3. Choose Add Printer. The Add Printer Wizard will start.
4. Next, the Wizard will ask you if you want to install on My
Computer or on a Network print server. Choose My Computer
and click Next.
AXIS 5570e/AXIS 5670e User’s Manual
Section 11: Configuration Possibilities
5. In the Available Ports window, click Add Port:
6. The Printer Ports dialog will appear, showing a list of Available
Printer Ports.
7. Choose The HP Internet Printer Connection Port and click New
Port.
8. The HP Internet Printer Connection will start. Click Next.
213
214
Section 11: Configuration Possibilities
AXIS 5570e/AXIS 5670e User’s Manual
9. In the IP Address, Host Name or URL field, type the http://
address of the AXIS 5570e/AXIS 5670e to which the destination
printer is connected. The URL will automatically appear in the
Port Name field as well:
Example:
http://171.16.5.218:631/LPT1 if you want to address the parallel
port or
http://171.16.5.218:631/USB1 to address the USB port.
Click Next.
10. The Wizard will confirm the information you have entered. Click
Finish to complete the installation and go back to the Available
Ports list.
11. The IPP printer port list is now available in the Available Ports
list. Click Next.
AXIS 5570e/AXIS 5670e User’s Manual
Section 11: Configuration Possibilities
12. Next, choose a suitable driver for the destination printer and
install it. Click Next
.
13. You will be asked if you want the newly added printer to be your
default printer and if you want to share the printer on your
network with other users. Choose the alternatives that suit your
printing needs and click Finish to complete the installation.
215
216
Section 11: Configuration Possibilities
AXIS 5570e/AXIS 5670e User’s Manual
14. The new printer will appear in your Printer window. You are now
ready to start printing using IPP.
How to Print from
Windows 2000/XP
Before you print to an IPP printer you will need to know:
• the http:// address of the print server. The http:// address contains the IP address or host name of the print server and the
printer port name.
• the brand and type of the printer in order to install the appropriate printer driver.
1. Select the IPP printer to which you want to send your document.
Choose the destination printer from the Select Printer field (in
File | Print).
If your destination printer does not exist in your Select Printer
list, you need to add it. Adding an IPP printer to your printer list is
described below.
2. When you press Print, the print job is sent over the Internet to
the AXIS 5570e/AXIS 5670e, which then forwards the print job to
the destination printer.
AXIS 5570e/AXIS 5670e User’s Manual
Section 11: Configuration Possibilities
3. The recipient of the print job can collect the print job at the
destination printer.
Adding an IPP Printer
to your Printer List in
Windows 2000/XP
1. Choose File | Print from the document you wish to print.
2. In the Select Printer field, click the Add Printer icon. The Add
Printer Wizard will start. Click Next.
3. The Wizard will ask you if you want to install a local printer or a
network printer. Choose Network Printer and click Next.
4. Enter the printer http:// address in the URL field.
Example:
http://171.16.5.218:631/LPT1 if you want to address the parallel
port or
http://171.16.5.218:631/USB1 to address the USB port.
Click Next.
5. If you do not have a driver corresponding to the destination
printer installed on your computer, the Wizard will prompt you to
install one. Click OK.
217
218
Section 11: Configuration Possibilities
AXIS 5570e/AXIS 5670e User’s Manual
6. The Installation Wizard will ask you to select a printer driver
corresponding to the destination printer. Select the printer driver
from the list and click OK.
7. The Wizard will ask you if you want the printer to be your default
destination printer. Make your choice and click Next to complete
the Add Printer Wizard installation.
AXIS 5570e/AXIS 5670e User’s Manual
Section 11: Configuration Possibilities
8. The new printer is added to your Select Printer window:
9. You are now ready to print using IPP: specify your new
destination printer from the printer list and click Print.
219
220
Section 11: Configuration Possibilities
AXIS 5570e/AXIS 5670e User’s Manual
Logical Printers for Customized Printing
The AXIS 5570e/AXIS 5670e has a powerful facility for altering the
print data. This means that your desired print format can be realized
on any type of printer. The following actions can be invoked from the
print server:
• The character set can be changed to suit the printer
• Strings can be added before and after the print data
• Strings within the print data can be substituted
• ASCII to PostScript conversion
• Redirection of print data to another printer if the printer is busy
• Hex Dump mode to assist with printing problems
If any of these actions are required, a Logical Printer is used to
change the print data before being sent to the printer port. There are
eight logical printers (PR1-PR8) that can be set up to filter the print
data.
The default logical printers settings are such that PR1—PR4 cause no
change to the flow of print data, while PR5—PR8 add CR to LF control
characters:
Logical Printer
Changes to data
PR1
no change
PR2
no change
PR3
no change
PR4
no change
PR5
add CR to LF
PR6
add CR to LF
PR7
add CR to LF
PR8
add CR to LF
Each logical printer can be set via the print server’s internal Web
pages: Open a Web browser, enter the IP address of the print server in
the Location/Address field and select Admin | Logical Printers.
The logical printers can also be set up by editing the config file. See
“Editing the config file” on page 192.
AXIS 5570e/AXIS 5670e User’s Manual
Section 11: Configuration Possibilities
Notes:
• The examples in this section describe how you can configure the available logical printers
using a standard Web browser. If you want to set them directly by editing the config file,
just enter the values for the corresponding parameters.
• The examples should only be viewed as suggestions how to configure the logical printers.
You should, of course, configure them according to the needs of your network.
• In the Parameter List chapter of this manual, you can find a complete list of the AXIS
5570e/AXIS 5670e parameters.
Character Set
Conversion
A common problem in a multiple host environment is that different
hosts use different ASCII character sets. As a result of this, language
specific characters (such as å ü ô ñ) are sometimes printed
incorrectly.
The AXIS 5570e/AXIS 5670e solution to this problem is to assign a
character set conversion filter to a logical printer, and then link that
logical printer to the host causing the problem.
You select your desired conversion filter by setting the Character Set
Conversion (PRx_CSET.) parameter. The output from the conversion
filter is always IBM PC Set 2 (Code Page 437), and this is the
character set the printer must be set up for.
Example:
Your network contains a host using the character set ISO 8859-2 and a host using the
character set DEC.
In order to direct print jobs to the printer connected to the AXIS
5570e/AXIS 5670e, you should assign the host to a separate logical
printer, and install a character set conversion filter.
Follow the instructions below to change the conversion filter (USB1 is
used as an examlpe here):
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR1 tab.
221
222
Section 11: Configuration Possibilities
AXIS 5570e/AXIS 5670e User’s Manual
3. Set the parameter Physical Port to USB1.
4. Set the parameter Character Set Conversion to ISO>IBM.
5. Click the OK button.
6. Select the PR2 tab.
7. Set the parameter Physical Port to USB1.
8. Set the parameter Character Set Conversion to DEC>IBM.
9. Click the OK button.
The ISO 8859-2 printer data that is sent to logical printer PR1
converts to IBM PC Set 2 and is printed on USB1. Similarly, the DEC
printer data that is sent to logical printer PR2 converts to IBM PC Set
2 and is printed on USB1.
Adding Strings Before
and After Print Jobs
These string functions provide a way to send printer control
commands before and after each print job. They may be specified
individually for each logical printer.
All strings are entered as hexadecimal byte values.
Example:
Assume that the logical printer PR5 is configured as a PostScript printer and that you want to
append the PostScript End of File character (hex 04) after each print job.
Follow the instructions below to add a string after the print job:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR5 tab.
3. Enter the string 04 in the String After Print Job text field.
4. Click the OK button.
AXIS 5570e/AXIS 5670e User’s Manual
Section 11: Configuration Possibilities
Example:
You have an HP LaserJet printer with dual trays, and want to print on pre-printed forms when
using the logical printer PR4. The standard forms are taken from the lower tray, and the preprinted forms are taken from the upper tray. The string before print job should contain the
command to select the upper tray: EC&l1H (hex 1B 26 6C 31 48). The string after print
job should contain the command to select the lower tray: EC&l4H
(hex 1B 26 6C 34 48).
Follow the instructions below to add strings before and after the
print job:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR4 tab.
3. Enter the string 1B 26 6C 31 48 in the String Before Print Job
text field.
4. Enter the string 1B 26 6C 34 48 in the String After Print Job
text field.
5. Click the OK button.
String Substitutions
The string substitution function performs search and replace
operations on the print data. The primary application is to replace
printer control commands. Up to twenty string substitutions may be
specified individually for each logical printer.
All strings must be entered as hexadecimal byte values, and each
match and substitute string must be preceded by a count byte.
You substitute command strings by editing the String Substitutions
(PRx_STR.) parameter.
Example:
Assume that you want to replace the UNIX/Linux New Line (hex 0A) with an Carriage
Return/Line Feed (hex 0D 0A) for logical printer PR1.
Follow the instructions below to substitute command strings:
223
224
Section 11: Configuration Possibilities
AXIS 5570e/AXIS 5670e User’s Manual
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR1 Web page.
3. Enter the string 01 0A 02 0D 0A in the String Substitutions
text field.
Hex Code
Explanation
01
length of the string you want to replace
0A
the string you want to replace
02
length of the substitute string
0D 0A
the substitute string
4. Click the OK button.
This conversion is the default setting for logical printers PR5 through
PR8.
Example:
Assume that you want to replace the UNIX/Linux New Line (hex 0A) with an Carriage
Return/Line Feed (hex 0D 0A), and the printer command ECG1 (hex 1B 47 31) with
E Y (hex 1B 59) for logical printer PR2.
C
Follow the instructions below to substitute command strings:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR2 tab.
AXIS 5570e/AXIS 5670e User’s Manual
Section 11: Configuration Possibilities
3. Enter the string 01 0A 02 0D 0A 03 1B 47 31 02 1B 59 in the
String Substitutions text field.
Hex code
01
Explanation
length of the UNIX/Linux New Line command
0A
the UNIX/Linux New Line command
02
length of the Carriage Return/Line Feed command
0D 0A
the Carriage Return/Line Feed command
03
length of the printer command to replace
1B 47 31
the printer command to replace
02
length of the new printer command
1B 59
the new printer command
Click the OK button.
Note:
Extensive use of string substitutions will naturally decrease the throughput rate of the AXIS
5570e/AXIS 5670e.
ASCII to Postscript
Conversion
The AXIS 5570e/AXIS 5670e logical printers can translate ASCII print
data into PostScript format. This makes it possible to print on a
PostScript printer from a host that does not support PostScript. The
conversion is selected by activating a filter that converts ASCII data
into Postscript. This filter can be activated individually for each
logical printer.
225
226
Section 11: Configuration Possibilities
AXIS 5570e/AXIS 5670e User’s Manual
Activate your desired filter by setting the Printer Language
Translation (PRx_FILT.) parameter.
Example:
Follow the instructions below to convert ASCII print data to
PostScript for logical printer PR2:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR2 tab.
3. Set the Printer Language Translation parameter to POSTSCR.
4. Click the OK button.
If you select the parameter value AUTO_PS, the print data for every
print job is searched and if any ASCII data is found, it is translated
into PostScript. This setting is recommended if you are not sure if the
print data is ASCII or PostScript.
PostScript Settings
When a logical printer is set for PostScript conversion, you must
specify the following:
• page size
• page orientation
• page format
• which font to use
The default page size is A4 and the default page orientation is
Portrait, while the page format parameters are as follows:
Page Format Parameter
Lines per page (MPL)
Default Value
Comment
66
Characters per line (MPP)
0
0 = disable line wrap
Characters per inch (CPI)
100
100 = 10 char per inch
Lines per inch (LPI)
60
60 = 6 lines per inch
Left margin (LM)
30
30 = 3.0 mm
Top margin (TM)
50
50 = 5.0 mm
AXIS 5570e/AXIS 5670e User’s Manual
Section 11: Configuration Possibilities
The PostScript font can be any font that is installed in the printer. If
no font is specified, Courier will be used.
Example:
Follow the instructions below to set the PostScript parameters for
logical printer PR2:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR2 tab.
3. Set the Printer Language Translation parameter to POSTSCR.
4. Set the PostScript Page Size parameter to LETTER.
5. Set the PostScript Page Orientation parameter to LANDS.
6. Enter the string 48 0 120 60 30 50 in the PostScript Page
Format text field.
Hex code
Explanation
48
48 lines per page
0
disable line wrap
120
120 = 12 characters per inch
60
60 = 6 lines per inch
30
30 = 3 mm left margin
50
50 = 5 mm top margin
7. Enter the string Helvetica in the PostScript Font text field.
8. Click the OK button.
Redirecting Print Jobs
when a Printer is Busy
If print data is received for a printer that is already busy, the host
normally must wait. However, with a two-port print server it is
possible to use a logical printer to redirect the print data to another
logical printer when the target printer is busy. If the second printer is
also busy, the host must wait until the target printer is ready.
Example:
Follow the instructions below to redirect PR1 print jobs to PR3, when
the printer assigned to PR1 is busy (USB1 and LPT2 are used as
examples here):
227
228
Section 11: Configuration Possibilities
AXIS 5570e/AXIS 5670e User’s Manual
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR1 tab.
3. Set the Physical Port parameter to USB1.
1. Set the Secondary Printer parameter to PR3.
2. Set the Wait On Busy parameter to NO.
3. Click the OK button.
4. Select Admin | Logical Printers and the PR3 tab.
5. Set the Physical Port parameter to LPT2.
6. Click the OK button.
Notes:
• The two printers must use the same printer driver.
• Logical Printer redirection cannot be nested. If PR3 is redirected to another logical printer,
the print job will not be redirected if PR3 is busy.
• If both printers are busy, the print job will be printed on the printer that first finishes its
active print job.
AXIS 5570e/AXIS 5670e User’s Manual
Read Back of
information
Example:
Section 11: Configuration Possibilities
The AXIS 5570e/AXIS 5670e support bi-directional printing. The
information from the printer is read back on the parallel port when
the parameter Read Back Port (PRx_IN.) has the default setting of
AUTO. However, it is required that the printer also supports bidirectional printing. Please refer to your printer documentation for
further details regarding bi-directional printing support.
Follow the instructions below to disable the bi-directional
communication for logical printer PR1:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR1 tab.
3. Set the Read Back Port parameter to NONE.
4. Click the OK button.
Debugging using the
Hex Dump Mode
When hex dump mode is enabled, the print data is printed as
hexadecimal byte values rather than characters; printer control
commands are also printed as hex values. This allows you to inspect
what control and print characters are actually being sent to the
printer, which is a useful debugging facility for more difficult printing
problems.
Example:
Follow the instructions below to enable the hex dump mode for PR3:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR3 tab.
3. Set the Hex Dump Mode Enabled radio button to YES.
4. Click OK.
Note:
The page length for hex dump printouts is determined by the lines per page
value of the PostScript page format parameter.
229
230
Section 11: Configuration Possibilities
AXIS 5570e/AXIS 5670e User’s Manual
Network Speed
With the Network Speed parameter you can manually specify the
speed at which you will send and receive network packages. You can
change the Network Speed setting to correspond to the type of
network you are using (10 or 100 Mbit).
To change the Network Speed in an Ethernet network, log in to the
print server’s internal Web pages and click Admin | General Settings
=>Change. From here, you have the option of setting the network
speed to:
Network Speed
Comment
AUTO_SENSE
This is the default value where the print server detects which speed is optimal for each network package you transfer.
10_HALF__DX
10 Half Duplex
10_FULL_DX
10 Full Duplex
100_HALF_DX
100 Half Duplex
100_FULL_DX
100 Full Duplex
NetWare Packet Signature
Level 1,2,3
Protects servers and clients using the NetWare Core Protocol™
services. NCP packet signature prevents packet forgery by requiring
the server and the client to sign each NCP packet.
Flash Loading of Firmware over the Web
The firmware can easily be upgraded, since flash loading over the
Web is possible from the print server’s internal Web pages. Client
software is not needed to upgrade the firmware. See Upgrading the
Firmware, on page 236.
AXIS 5570e/AXIS 5670e User’s Manual
Section 11: Configuration Possibilities
Secure Web Services — SSL/TLS
In a new and unconfigured AXIS 5570e/AXIS 5670e, SSL/TLS is
disabled.
Certificates
To use SSL/TLS you have to create or obtain a digital certificate. There
are two kinds of certificates: self-signed certificates and third party
certificates.
• Self-signed certificates are less secure but normally they are sufficiently secure for small networks with no public access. You generate such a certificate yourself and there are no fees to pay.
• For large networks and for networks with public access, third
party certificates from a trusted source are normally used. You
obtain them for a yearly fee from a Certificate Authority (CA).
Among other things, a certificate gives information about which
domain it is issued for, its validity and the name of issuer. With
SSL/TLS enabled, the installed certificate authenticates the print
server to the client and all information exchanged between them will
be encrypted.
Enabling SSL via the
Web Interface
You enable the print server’s secure Web services through its internal
Web pages. If you have a valid certificate loaded, select Admin |
Network Settings | Detailed View| TCP/IP and set the HTTPS
Enabled parameter to Yes.
If you do not have a valid certificate loaded, select Admin | Security
Settings and click Create.
Decide whether you want to generate a self-signed certificate or if
you want to generate a certificate request.
Generating a SelfSigned Certificate
Select the Generate Self-Signed Certificate radio button and click
Next.
231
232
Section 11: Configuration Possibilities
AXIS 5570e/AXIS 5670e User’s Manual
Enter the data asked for:
• Country Name: Example: US
• State or Province Name: Example: California
• Locality Name: Example: Los Angeles
• Organization Name: Example: Printers Inc
• Organizational Unit Name: Example: Sales Dept
• Common Name*: Example: [email protected]
• Current Date (yyyy/mm/dd): Example: 2003/03/27
• Validity Duration (in days): Example: 365
* Common Name denotes the name given to the print server in the network. If
you do not have a DNS server on your network, you must include the domain
name, e. g. [email protected]
AXIS 5570e/AXIS 5670e User’s Manual
Section 11: Configuration Possibilities
Click Finish and the print server will generate a public/private key
pair as well as the self-signed certificate itself (this process will take
a few minutes) and store these data in the print server. When the
certificate is generated, the print server automatically loads it into
your present browser session. The browser reports the new state by
changing into https mode. In the browser’s Security Alert box, select
View Certificate and Install Certificate. Follow the instructions of
the Install Certificate wizard.
Generating a
Certificate Request
Select the Generate Certificate Request radio button and click Next.
Enter the data asked for:
• Country Name: Example: US
• State or Province Name: Example: California
• Locality Name: Example: Los Angeles
• Organization Name: Example: Printers Inc
• Organizational Unit Name: Example: Sales Dept
• Common Name*: Example: [email protected]
• Current Date (yyyy/mm/dd): Example: 2003/03/27
• Validity Duration (in days): Example: 365
* Common Name denotes the name given to the print server in the network. If
you do not have a DNS server on your network, you must include the domain
name, e. g. [email protected]
Click Finish.
Now the print server will generate a public/private key pair and a
PEM-encoded Certificate Request, called cert.pem. Click Save, Save
this file to disk and Save.
Send this Certificate Request to your Certificate Authority for their
signature.
233
234
Section 11: Configuration Possibilities
AXIS 5570e/AXIS 5670e User’s Manual
Importing a Certificate
When you receive the PEM-encoded certificate from your Certificate
Authority, open the print server’s Web interface and select Admin |
Security Settings. Click Import and follow the instructions on the
screen.
https://
Whenever SSL/TLS is enabled, you can only reach the print server’s
Web interface through the secure services. The unsecure way via
http:// is closed and now you have to address the print server’s Web
interface in the secure way, i.e. via https://.
Disabling Protocols
To further increase security, you must disable protocols that are
considered insecure;
• FTP (used by AXIS ThinWizard. If FTP is disabled, AXIS ThinWizard
can not function properly.)
• Telnet
• Auto-IP
• DHCP
• BOOTP
• Remote Config (used by AXIS NetPilot)
• SNMPv1 Configuration
To disable these protocols, go to Admin | Security Settings |
Protocol Settings | Detailed View and mark the check boxes. Click
OK to finish. Only enabled protocols will be visible from this view!
To enable these protocols, select Admin | Network Settings |
Detailed View | TCP/IP for FTP, Telnet, AutoIP, DHCP and BOOTP.
Remote Config is enabled via Admin | General Settings | RConfig
Support.
AXIS 5570e/AXIS 5670e User’s Manual
Section 11: Configuration Possibilities
Important:
To ensure maximum security, it is highly recommended that you change your
Administrator password after generating a certificate and disabling insecure
protocols! This is done from Admin | General Settings | Change => | General |
Root Password.
Checking
SSL/TLS Status
To check SSL/TLS status, open the print server’s Web interface and
select Admin | Network Settings | Detailed View| TCP/IP to see if
the HTTPS Enabled parameter is set to Yes or No.
To View a Certificate
To view a Certificate, open the print server’s Web interface, select
Admin | Security Settings and click View next to the Certificate.
To Delete a Certificate
To delete a Certificate, open the print server’s Web interface, select
Admin | Security Settings and click Delete next to the Certificate.
235
236
Section 12: Upgrading the Firmware
Section 12
AXIS 5570e/AXIS 5670e User’s Manual
Upgrading the Firmware
Upgrading the Firmware
You can upgrade the AXIS 5570e/AXIS 5670e firmware using one of
the following methods:
•
•
•
AXIS ThinWizard (TCP/IP)
From the print server’s internal Web pages (TCP/IP)
FTP (TCP/IP)
Note:
Updating instructions are supplied with the firmware release notes.
Upgrading from the
Print Server’s Internal
Web Pages
Follow these instructions to upgrade the firmware of your print server
from its internal Web pages (flash loading over the Web):
1. Open your Web browser, enter the IP address of your print server
and press Enter. (See Print Server Management, on page 85 for
detailed instructions on accessing your Axis print server on the
Web).
2. From the Admin mode, click the Firmware Upgrade button. From
here you can upgrade your print server with the latest available
firmware.
Upgrading using
AXIS ThinWizard
AXIS ThinWizard 3.0 is a tool that enables batch upgrading of several
print servers and can be used for upgrading the print server’s
firmware in TCP/IP networks.
You must assign an IP address to the print server, as described earlier
in this manual, before you can use this upgrading method.
Follow the instructions below to upgrade your print servers using
AXIS ThinWizard:
AXIS 5570e/AXIS 5670e User’s Manual
Section 12: Upgrading the Firmware
1. Click the Firmware button. The Firmware Wizard starts.
2. Browse through the upgrading tips and click Next > when you are
done. Select Latest Available Version. Click Next >.
3. Select the servers you want to upgrade, by checking the correct
upgrade boxes. Click Next >.
4. Enter the default User ID and Password of the servers you selected
in the previous step. Select whether you want AXIS ThinWizard to
verify the password immediately or when the upgrading job has
started, by checking the appropriate box. Click Next >.
5. If you do not have a default password, just click Next >. If some
of your servers use a different User ID or Password than the default
entries, they will be displayed in the Remaining servers list. Enter
the User ID and Password for each individual server. Click Next >.
6. Name the upgrade job. This is optional, so you can leave the field
blank if you want. Click the Start button to start the upgrading job.
Refer to Using AXIS ThinWizard software for Print Server
Management, on page 92, for more information about AXIS
ThinWizard.
237
238
Section 12: Upgrading the Firmware
Upgrading using FTP
AXIS 5570e/AXIS 5670e User’s Manual
To upgrade over the network using FTP you will need a file with the
new print server firmware. The name of this file is in the form
product_version.bin.
You can use any of the previously mentioned methods to obtain the
new file. You must assign an IP address to the AXIS 5570e/AXIS
5670e before you can use this upgrading method.
Caution!
Be careful not to interrupt the file transfer. If the transfer is interrupted, the AXIS
5570e/AXIS 5670e may have to be re-initialized by your dealer.
The objective of this example is to upgrade a print server with
firmware version 6.41 to firmware version 6.42.
This description from Windows XP uses the following examples:
•
•
•
•
Print server model: AXIS 5570e
IP address of print server: 10.13.4.105
New firmware version name: 5570e_v2_6_42.bin
Location of firmware and upgrade procedure: C:\Axis
(Create a new file named e.g. ‘Axis’ on your hard drive and
download the firmware to that location).
1. From www.axis.com, download the firmware and save it to a file
on your computer, e.g. C:\ Axis
2. Open a command prompt from Start => Run.
The Run window will appear.
Type cmd and click OK.
3. The DOS Command Prompt window will open.
Type c: and press the Enter button on your keyboard.
4. The firmware is saved in C:\Axis
Type cd Axis
5. Type dir and press Enter.
The Axis directory you have created will list all files:
AXIS 5570e/AXIS 5670e User’s Manual
Section 12: Upgrading the Firmware
6. Connect to the print server using ftp.
Type ftp 10.13.4.105
(Example using print server IP address 10.13.4.105)
7. Type root after "User:", press Enter.
Type pass after "Password:" (your entry will not be visible) press
Enter.
8. Change to binary mode transfer.
Type bin HASH (or binary HASH) and press Enter.
9. Use the 'put' command to upload the upgrade file to the flash
location:
(Example using firmware named 5570e_v2_6_42.bin):
Type put 5570e_v2_6_42.bin FLASH (FLASH written in capital
letters!)
Wait 30 seconds... Done! You will receive a message stating "Transfer
complete. Flash programming finished OK. "The print server will
restart in five seconds running the new software. When you see a
new ftp prompt the procedure has been completed successfully.
Obtaining the Software
You can obtain all the print server firmware as well as the latest
utility software from the following locations:
•
•
http://www.axis.com
your local dealer
239
240
Section 13: SNA Parameter Overview
Section 13
AXIS 5570e/AXIS 5670e User’s Manual
SNA Parameter Overview
This appendix provides summary information on the parameters that
control the basic operation of the SNA communication and the IBM
printer emulation. It also describes how these parameters may be
changed.
An overview of how parameters are mapped during the autoconfiguration process is also provided.
Refer to the Parameter List document on www.axis.com for a
complete description of the Axis Print server parameters.
Communication Parameters
In most environments, the basic communication parameters need to
be customized in order to establish a communication link to the host
system. This includes setting the Host MAC Address and Host Name
parameters in the Print Server. In this chapter you will find
instructions on how to update these parameters.
SNA Communications
Process
There are several parameters that control the basic operation of the
SNA communication, and IBM printer emulation. The diagram below
shows how they relate to the SNA printing process.
SNA Communication
Settings
IBM Printer
Settings
Printer Driver
Settings
Network
Printer
Device Emulation
MAC Address
Service Access Point
Node ID
Network Name
LU Name
CP Name
IBM Printer Emulation
System Language
Paper Size
Page Orientation
ASCII Printer Driver
Schematic diagram displaying basic SNA operation and IBM printer emulation
AXIS 5570e/AXIS 5670e User’s Manual
Parameter Summary
Section 13: SNA Parameter Overview
The following tables summarize SNA host communication parameters
that must be considered when installing the AXIS 5570e/AXIS 5670e.
The parameters are presented as:
•
Common Mainframe and AS/400 parameters
•
Mainframe specific parameters
•
AS/400 specific parameters
Common Mainframe &
AS/400 Parameters
Parameter
Name
Default
DEVICE_EMUL
Control Unit Device
Emulation
3174
Th DEVICE_EMUL parameter controls the Control Unit emulation mode. When set to 3174, the Print
Server will appear as a 3174 PU 2.0 node to the host. This mode may be used for both mainframe and
AS/400 environments.
When set to 5494, the Print Server will appear as a 5494 PU2.1 node to the host. This is the
recommended mode for the AS/400 environment. The 5494 mode cannot be used in the mainframe
environment.
H1_ADDR
Host MAC Address
FF FF FF FF FF FF
The H1_ADDR is the Host Ethernet MAC address. It is normally set to the MAC address of the host.
When the Print Server is connected to the host through a gateway, this parameter should be set to the
MAC address of the gateway. For a directly attached AS/400 system, this value is found in the "Line
Description".
AUTODIAL
Automatic Link
Establishment
no
The AUTODIAL parameter controls whether the print server will automatically try to establish the link
when the print server is switched on, or if communication is lost.
When running 5494 CU mode, this parameter also controls whether Automatic Configuration should be
performed.
241
242
Section 13: SNA Parameter Overview
AXIS 5570e/AXIS 5670e User’s Manual
Mainframe Specific
Parameters
Parameter
Name
Default
NODE_ID
Node ID
E07xxxxx, where "xxxxx" are the last five digits of the
Print Server’s MAC address.
This is the SNA PU identification.
The first 3 digits is the IDBLK and the last five is the IDNUM.
When defining a VTAM Switched Major Node, this parameter should match the IDBLK and IDNUM values
specified in the PU definition.
Only Hexadecimal characters (0-9 and A-F) allowed.
AS/400 Specific
Parameters
Parameter
Name
Default
Emulation
NWORK_NAME
Network Name
APPN
5494 only
Description - This is the Print Server Network Name.
The value of this parameter is normally the same as the "Host Network Name", indicating that both the
Print Server and the AS/400 system are located on the same APPN network.
The Network Name may comprise the letters A-Z and/or numerals 0-9, but must begin with a letter.
The letters used should all be in UPPERCASE and a maximum of 8 characters are allowed.
LU_NAME
LU Name
Axxxxxxx
5494 only
Description - Axxxxxxx, where "xxxxxxx" is the last 7 characters of the AXIS 5570e/AXIS 5670e serial
number, in reverse order, e.g.
if s.no. =
00 40 8C 1B 06 D4 the default LU Name =
A4D60B1C.
This will be the name of the APPC device and controller
created during auto-configuration
Description - Axxxxxxx, where "xxxxxxx" is the last seven characters of the Print Server serial number, in
reverse order, i.e. a print server with serial number 00 40 8C 1B 06 D4 will have the default CP Name
A4D60B1C. This will be the name of the APPC controller created during auto-configuration.
H1_NW_NAME
Host Network Name
APPN
5494 only.
H1_LU_NAME
Host LU Name
DEFAULT
5494 only
AXIS 5570e/AXIS 5670e User’s Manual
Section 13: SNA Parameter Overview
Updating parameters
This is most easily done from the internal web pages of your AXIS
5570e/AXIS 5670e. To set the parameters using a Web browser, you
first need to assign an IP address to the AXIS 5570e/AXIS 5670e. For
instructions on how to do this, refer to Setting the IP address, on page
24.
Alternatively, you can update the parameters via FTP, TFTP or by using
extended IBM printer emulation.
Using extended IBM printer emulation means setting up the AXIS
5570e/AXIS 5670e by printing a file containing extended IBM
emulation commands to it after you have established communication
with your IBM host. The configuration is started by inserting the
sequence %CONFIG+ in your text. To protect your settings, a password
must be provided. By default, the password is pass. You may then set
the parameter values directly using the syntax shown below:
Syntax:
<Parameter name> = <value> [, <value>];
When all parameters have been set the SAVE command saves the
settings permanently. The %CONFIG- command resumes normal
printing. In order to maintain backward compatibility, some
parameters must be preceded by a %CONFIG++ command. See also
The Parameter List, on page 295.
243
244
Section 13: SNA Parameter Overview
AXIS 5570e/AXIS 5670e User’s Manual
To set the parameters to their default values, enter the following in
your document and print it.
%CONFIG+ password (If you have not changed the default
password (pass), the password is optional.)
PRDRIVER = PCL5;
%CONFIG++
NODE_SAP = 4;
H1_SAP = 4;
AUTODIAL = NO;
%CONFIG-PREMUL = 3816;
SYSL = 37;
BIN1 = LETTER, COR;
SAVE;
%CONFIG-
Changing
Parameters after
Auto-configuration
If you want to change some of the critical configuration parameters
after auto-configuration is completed, you should first set AUTODIAL
to NO, then remove all descriptions in the AS/400, and then change
the parameter(s) and set AUTODIAL to YES to initiate a new
configuration process.
AXIS 5570e/AXIS 5670e User’s Manual
Section 13: SNA Parameter Overview
Auto-configuration and Mapping
The configuration created in the AS/400 and the mapping to the AXIS
5570e/AXIS 5670e as a result of the auto-configuration process is
illustrated by the figure below.
Configuration in the
AXIS 5470e
LU 6.2 conversation
Configuration in the
AS/400
APPC-controller
APPC-device
Logical mappings
RWS-controller
Logical Printer #1
Printer device #1
Logical Printer #2
Printer device #2
Logical Printer #3
Printer device #3
Illustration of the configuration created in the AS/400 and the mapping to the AXIS
5570e/AXIS 5670e as a result of the auto-configuration
Printer Device
Descriptions
Through auto-configuration, the APPC controller, APPC device, RWS
controller as well as printer device descriptions for the logical
printers, will be created automatically.
Controller and Device
Names
The names of the controllers and devices created in the AS/400
during auto-configuration are by default the last 7 characters from
the AXIS 5570e/AXIS 5670e serial number in reverse order, preceded
by the letter "A".
For example, serial number "00408C180102" will result in APPCcontroller "A201081C", APPC-device "A201081C" and RWScontroller "A2010RMT".
245
246
Section 13: SNA Parameter Overview
AXIS 5570e/AXIS 5670e User’s Manual
Printer devices will be named "A201PRT01", A201PRT02",
A201PRT02"… The designation "PRTnn" corresponds to the logical
printers in the Print Server, i.e. printer device "A201PRT01" will be
mapped to Logical Printer #1. By default, all Logical Printers are
mapped to the Physical Port LPT1.
To customize the print server, proceed to the SNA Printing - 5494
Mode, on page 36.
AXIS 5570e/AXIS 5670e User’s Manual
Section 14
Gateway
Configuration,
3174 CU mode
Pass-through gateway
Section 14: SNA Gateways
SNA Gateways
Some hints specific to SNA gateways are given below.
•
AXIS 5570e/AXIS 5670e appears to a gateway as a Down Stream
Physical Unit (DSPU), with eight LUs, 1 to 8 (LU 1 may not be
available).
•
Only gateways that communicate with DSPUs using SNA over
LLC type 2 are supported.
•
There are basically two types of gateways that the AXIS
5570e/AXIS 5670e can be attached to: pass-through gateways
and concentrator gateways, as described below.
Devices attached downstream to this type of gateway are completely
visible to the host. In other words, each DSPU will have a PU
definition on the host. Examples of pass-through gateways are IBM
3745 Communications Controller, IBM 3174 Establishment
Controller, IBM 3172 LAN Interconnect Controller, etc.
You need to set up at least one PU and LU definition for each AXIS
5570e/AXIS 5670e on the host, as described in the VTAM section.
When attaching an AXIS 5570e/AXIS 5670e to a remote passthrough gateway, you need to set the mapping of SDLC or subchannel address to MAC address in the gateway.
247
248
Section 14: SNA Gateways
Concentrator gateway,
general
AXIS 5570e/AXIS 5670e User’s Manual
A concentrator gateway typically behaves as a PU (or a few PUs) to
the host, even though a number of PUs may be available downstream.
If it is an SDLC or channel attached gateway, typically only one SDLC
or sub-channel address will be used. Examples of concentrator
gateways are: IBM Communications Manager/2 (OS/2), Novell
NetWare for SAA (NetWare 3.x), Microsoft SNA Server (Windows NT),
etc.
When an AXIS 5570e/AXIS 5670e is attached to this type of gateway,
you can map the chosen AXIS 5570e/AXIS 5670e LU to any host LU
you like. This way, several print servers may be accessed through the
same gateway.
Pooling LUs may not be used for AXIS 5570e/AXIS 5670e.
Concentrator Gateway,
NetWare
This is an outline of the procedure for configuring to a Novell
NetWare for SAA v 2.0 Server. More information is provided in the
‘Suppor’t section of www.axis.com
1. Customize the AUTOEXEC and STARTUP files on the server. Add
the LOAD statements for the LAN and WAN cards, the BTRIEVE
database, and the NetWare for SAA 2.0 Gateway
i.e. LOAD COMMEXEC and LOAD NWSAA.
2. Configure the Communication Executive (this and the following
subjects are done on a WorkStation).
3. Configure SNA Network ID. Either change the default value or let
it stay on default.
4. Configure Data Link Adapters. The configuration is done on the
Data Link Adapters Definitions screen by pressing insert for a
new adapter config, then you always enter the Logical adapter
name, Link type, Logical adapter number and Service status.
AXIS 5570e/AXIS 5670e User’s Manual
Section 14: SNA Gateways
5. Configure PU and LUs. On the Configure PU Profile screen you
can set default LU attributes, starting dependent LU address,
number of dependent LUs, give CP a name, enable off-line test
mode, status assignment of LUs activated by host, status call
host at workstation attach, status PU profile start-up and logical
adapter name. On the Configure Dependent LUs screen you can
set VTAM LU name, lock for a session, LU type and model and
preserve host session.
6. Assign LU Resources and Access Control Lists (ACLs). On the
Configure Dedicated LUs you can dedicate a LU to a person or
device or group of persons. This person(s) is described in the
access control lists.
7. Configure Downstream PU. Choose Configure Downstream PUs
and press insert. Give it a name and fill in starting LU address or
leave at default, type in number of DownStream LUs and logical
adapter name:
Configure Downstream PU Connection
Downstream PU name (CP name): _____________________________DPUname
Starting downstream LU address: ___________________________2
Number of downstream LUs: _________________________________1
Logical adapter name: _____________________________________
The CSCON adds new parameters according to the adapter type you
have set. The resulting screen can look like this:
Netware Comm Services Config V2.0 Wednesday 1999 September 4 16.27
Configure LUs for Downstream PUs _______________Downstream PU: AXIS5570e
DLU __Address __PU Profile __LU Address __LU Type __Model __VTAM LU Name
002 __(0x02) ____SAA_MAIN ____15 (0x0F) __Printer __________________ACP4
Concentrator gateway,
Microsoft
This is an outline of the procedure for configuring to a Microsoft SNA
Server. More information is provided in the Support section of the
Axis web site at http://www.axis.com
1. Configure host connection.
2. Configure downstream connection.
249
250
Section 14: SNA Gateways
AXIS 5570e/AXIS 5670e User’s Manual
3. Select host connection and assign one or more DownStream LUs
to it.
4. Select downstream connection and associate the DownStream
LUs (from step 3) with that connection.
5. If necessary, reorder the DownStream LU numbers, that is, the LU
numbers used by the downstream system.
6. To connect multiple PUs (boxes) repeat steps 2-5.
AXIS 5570e/AXIS 5670e User’s Manual
Section 15
Section 15: Extended IBM Printer Emulation
Extended IBM Printer Emulation
When printing from an IBM host, the AXIS 5570e/AXIS 5670e allows
you to make use of the following printer functions not found in
standard IBM printers:
•
Configuration Mode
•
Hex Transparency
•
User Defined Strings
•
String Substitutions
•
Bar Codes
•
Font Selection.
This appendix provides a brief overview of some of these functions.
Configuration Mode
The Configuration Mode provides a way to configure your AXIS
5570e/AXIS 5670e from your IBM system. For more information see
SNA Parameter Overview, on page 240.
User Defined Strings
The User Definable Strings are a set of 256 programmable sequences.
The UDS are useful for storing long sequences, such as printer
function sequences, within the AXIS 5570e/AXIS 5670e. Each
sequence can be activated by inserting a short control command in
your documents.
String Substitutions
The String Substitution function searches the output data stream for
specified sequences of AIC characters (Match Strings), and
substitutes them with other sequences (Substitute Strings). Up to 128
pairs of Match/Substitute Strings may be defined.
AIC (AXIS Internal Codes) are listed in the AXIS Network Print Server Technical
Reference.
251
252
Section 15: Extended IBM Printer Emulation
Font Selection
AXIS 5570e/AXIS 5670e User’s Manual
Fonts can be selected directly by FGID (Extended Emulation
commands or SCS SFG commands) or indirectly by pitch SCS SCD/SPD
commands.
Notes:
Hex Transparency
•
SFG control code is only supported by Twinax page printer emulations
•
Matrix printers only support a few fonts
The Transparency function allows you to send ASCII data to the
printer directly from the host application. The data may be Postscript,
PCL, HP-GL or any other language supported by the printer. This gives
you access to all the features of the connected printer from within
the IBM environment.
When the percent and less-than characters (%<) are received, the
AXIS 5570e/AXIS 5670e will switch to hex transparency mode. The
following data (given as hexadecimal byte values or quoted text) is
passed directly to the printer without any conversion. The hex
transparency mode continues until the greater-than and percent
characters (>%) are received.
The following example shows how to embed HP-PCL ‘start
underline’ (<ESC>&d0D) and ‘stop underline’ (<ESC>&d0@)
commands in your documents:
The word %<1B26643044>%underline%<1B266440>% is
underlined.
You can also use %<1B,"&d0D">%quoted text%<1B,"&d0@">%
Resulting printout:
The word underline is underlined
You can also use quoted text.
Bar Codes
The bar code function provides easy access to a range of standard bar
code types resident in the AXIS 5570e/AXIS 5670e. Bar codes can
only be printed on PCL printers.
AXIS 5570e/AXIS 5670e User’s Manual
Section 15: Extended IBM Printer Emulation
Before the bar codes can be printed, a bar code format has to be
defined. This format sets the type and size of the bar code to be
printed. Up to 16 formats can be predefined. The definitions are made
by setting up the BAR parameter.
The BAR parameter takes several arguments, separated by commas,
as shown below:
BAR <number>=<type>,<width>,<height>,<text mode>,
<check mode>;
•
number is the bar code definition number in the range 0–15. This
number is used to refer to the definition when printing the bar
code.
•
type is the predefined bar code type. Valid values are:
Value
Description
Value
Code 39
CODE128
Code 128
UPC version A
INT2OF5
2 of 5 Interleaved
EAN8
EAN-8
CODABAR
Codabar matrix
EAN13
EAN-13
CODE39
UPCA
Description
•
width is the bar code module width in 1/1000 inch. Valid range is
1 to 1000. The default value is 12.
•
height is the bar code element height in 1/24 inch. Valid range is
1 to 500. The default value is 12.
•
text mode selects if human readable text is printed under the bar
code or not. ‘YES’ or ‘ON’ will turn on text, ‘NO’ or ‘OFF’ will turn
off text. The default mode is ‘ON’.
•
check mode selects if a check digit will be generated or not. ‘YES’
or ‘ON’ will generate a check digit, ‘NO’ or ‘OFF’ will not generate
a check digit. The default mode is ‘ON’. The check digit will
always be generated for bar code types UPCA, EAN8 and EAN13,
regardless of the setting of check mode.
253
254
Section 15: Extended IBM Printer Emulation
AXIS 5570e/AXIS 5670e User’s Manual
To set up the BAR parameter, use the %CONFIG command in your
document. To print bar codes, bar code commands may be included
anywhere in your documents. They begin with ‘percent-slash’ (%/)
followed by the word BAR. Then follows the number of the bar code
definition to be used, a comma, and the sequence to be printed. The
command is ended by a semi-colon (;).
Setting up the bar code parameters and printing bar codes
%CONFIG+
BAR 0 = EAN8,12,4,ON;
BAR 1 = EAN8,12,8,ON;
SAVE;
%CONFIG%/BAR 0,"0123456"; %/BAR 1,"0123456";
Once the BAR parameter has been set up, you will only need to use
the bar code commands to print the bar codes
%/BAR 0,"0123456";
%/BAR 1,"0123456";
Resulting printout:
0123 4565
0123 4565
AXIS Cobra products
compatibility
The AXIS 5570e/AXIS 5670e supports a subset of the extended printer
emulation syntax of the AXIS Cobra products, including the bar codes
syntax. For more information, please refer to the AXIS Network Print
Server Technical Reference supplied on the AXIS Network Product CD.
AXIS 5570e/AXIS 5670e User’s Manual
Section 16
Font Selection,
Coax Printer
Emulations
Section 16: IBM Fonts
IBM Fonts
Fonts can be indirectly selected by the IBM system using pitch
selection (CPI). In order to gain full access to the fonts the AXIS
5570e/AXIS 5670e offers an alternative font selection command.
Please note that matrix printers only support a few fonts.
Font selection commands may be included anywhere in your
documents. They begin with ‘percent-slash’ (%/) followed by the
word FONT and the font number (Font Global Identifier, FGID). An
optional point size value, preceded by a comma, may be included. The
command is ended by a semi-colon (;).
The following example shows how to select the 10 CPI Courier (fixed
pitch) font.
%/FONT 11;This is 10 CPI Courier
Resulting printout:
This is 10 CPI Courier
Font Selection,
Twinax Printer
Emulations
Fonts are selected by a FGID (Font Global Identifier) and mapped to a
printer resident PCL font, selected to make a close match to the
original IBM font. The IBM to PCL font mapping is controlled by the
Font Definition Table. All entries in this table are fully editable, and
you can also add new entries.
Refer to DBCS Support, on page 279 for details on DBCS font types supported
by the AXIS 5570e/AXIS 5670e.
255
256
Section 16: IBM Fonts
Available Fonts
AXIS 5570e/AXIS 5670e User’s Manual
The fixed pitch fonts are not scalable. If a Point Size is specified, it
will be used to compress or expand the character spacing. (%/FONT
11,105; will compress the 10 CPI font to 10.5 CPI without changing
the size of the characters).
Pitch 5 CPI Fonts
Pitch 8 CPI Fonts
Pitch 10 CPI Fonts
FGID
IBM Font Name
244
Courier 5
245
Courier Bold 5
266
Courier Bold 8
3
OCR-B
5
Orator
11
Courier 10
12
Prestige Pica
13
Artisan 10
18
Courier Italic 10
19
OCR-A
20
Pica
30
Math Symbol 10
38
Orator Bold
39
Gothic Bold 10
40
Gothic Text 10
41
Roman Text 10
42
Serif Text 10
43
Serif Italic 10
46
Courier Bold 10
60
Prestige Bold 10
AXIS 5570e/AXIS 5670e User’s Manual
Pitch 12 CPI Fonts
Pitch 13.3 CPI Fonts
Pitch 15 CPI Fonts
Pitch 17 CPI Fonts
Pitch 18 CPI Fonts
Section 16: IBM Fonts
FGID
IBM Font Name
66
Gothic Text 12
68
Gothic Italic 12
69
Gothic Bold 12
70
Serif Text 12
71
Serif Italic 12
72
Serif Bold 12
80
Math Symbol 12
84
Script
85
Courier 12
86
Prestige Elite
87
Letter Gothic 12
91
Light Italic 12
108
Courier Bold 12
110
Letter Gothic Bold
111
Prestige Elite Bold
112
Prestige Elite Italic
204
Gothic Text 13
221
Prestige 15
223
Courier 15
225
Math Symbol 15
229
Serif Text 15
230
Gothic Text 15
252
Courier 17
253
Courier Bold 17
254
Courier 17 (sub/super)
258
Courier 18
257
258
Section 16: IBM Fonts
AXIS 5570e/AXIS 5670e User’s Manual
Pitch 20 CPI Fonts
281
Gothic Text 20
Pitch 25 CPI Fonts
289
Gothic Text 25
Pitch 26.7 CPI Fonts
290
Gothic Text 27
Proportional PSM Fonts
FGID
IBM Font Name
155
Boldface Italic
158
Modern
159
Boldface
160
Essay
162
Essay Italic
163
Essay Bold
173
Essay Light
175
Document
751
Sonoran-Serif 8-pt Roman Medium
1051
Sonoran-Serif 10-pt Roman Medium
1053
Sonoran-Serif 10-pt Roman Bold
Proportional Typographic
1056
Fonts (Fixed Point Size)
Sonoran-Serif 10-pt Roman Italic Medium
1351
Sonoran-Serif 12-pt Roman Medium
1653
Sonoran-Serif 16-pt Roman Bold
2103
Sonoran-Serif 24-pt Roman Bold
AXIS 5570e/AXIS 5670e User’s Manual
Proportional Typographic Fonts
(Scalable - User Defined FGIDs)
Section 16: IBM Fonts
FGID
IBM Font Name
3840
CG Times
3841
CG Times Bold
3842
CG Times Italic
3843
CG Times Bold Italic
3844
CG Omega
3845
CG Omega Bold
3846
CG Omega Italic
3847
CG Omega Bold Italic
3848
Coronet
3849
Clarendon Condensed
3850
Univers Medium
3851
Univers Bold
3852
Univers Medium Italic
3853
Univers Bold Italic
3854
Univers Medium Condensed
3855
Univers Bold Condensed
3856
Univers Medium Condensed Italic
3857
Univers Bold Condensed Italic
3858
Antique Olive
3859
Antique Olive Bold
3860
Antique Olive Italic
3861
Garamond Antiqua
3862
Garamond Halbfett
259
260
Section 16: IBM Fonts
AXIS 5570e/AXIS 5670e User’s Manual
Proportional Typographic Fonts
(Scalable - User Defined FGIDs)
Proportional Typographic Fonts
(Scalable Point Size)
3863
Garamond Kursiv
3864
Garamond Kursiv Halbfett
3865
Marigold
3866
Albertus Medium
3867
Albertus Extra Bold
3868
Arial
3869
Arial Bold
3870
Arial Italic
3871
Arial Bold Italic
3872
Times New
3873
Times New Bold
3874
Times New Italic
3875
Times New Bold Italic
3876
Symbol
3877
Wingdings
FGID
IBM Font Name
5687
Times Roman
5707
Times Roman Bold
5815
Times Roman Italic
5835
Times Roman Bold Italic
6199
Palatino
6219
Palatino Bold
6327
Palatino Italic
6347
Palatino Bold Italic
AXIS 5570e/AXIS 5670e User’s Manual
(cont.)
Proportional Typographic Fonts
(Scalable Point Size)
Section 16: IBM Fonts
16951
Century Schoolbook
16971
Century Schoolbook Bold
17079
Century Schoolbook Italic
17099
Century Schoolbook Bold Italic
33335
Optima
33355
Optima Bold
33463
Optima Italic
33483
Optima Bold Italic
33591
Futura Book
33601
Futura Heavy
33719
Futura Book Italic
33729
Futura Heavy Italic
34103
Helvetica
34123
Helvetica Bold
34231
Helvetica Italic
34251
Helvetica Bold Italic
41783
Cursive
41803
Cursive Bold
41911
Cursive Italic
41931
Cursive Bold Italic
261
262
Section 17: IBM Print Formatting
Section 17
AXIS 5570e/AXIS 5670e User’s Manual
IBM Print Formatting
This appendix provides general parameter information relating to
non-IPDS IBM print formatting.
IBM Printer Emulation
Coax Printer
Emulations
Mainframe
The following tables display the valid printer emulations that can be
used in coax and twinax printer emulations.
Parameter
PREMUL
Default
3816_cx
Printer
Emulation
Options
Printer Description
3812_cx
IBM 3812 model 2 non-IPDS, page printer
*3816_cx
IBM 3816 models 01A and 01D non-IPDS, page
printer with 5219 diskette
3287_cx
IBM 3287 model 2C, matrix printer
3268_cx
IBM 3268 model 2C, matrix printer
3262_cx
IBM 3262 models 3 and 13, matrix printer
4214_cx
IBM 4214 model 1 matrix printer
4224_cx
IBM 4224 model 2 non-IPDS, matrix printer
4230_cx
IBM 4230 model 201 matrix printer
AXIS 5570e/AXIS 5670e User’s Manual
Section 17: IBM Print Formatting
Twinax Printer
Emulations
AS/400
Parameter
Name
PREMUL
3816_cx
System Languages
Default
Printer Emulation
Options
Printer Description
3812_tx
IBM 3812 model 1 and 2 page printer
3816_tx
IBM 3816 models 01S and 01D, page
printer with 5219 diskette
4214_tx
IBM 4214 model 2 matrix printer
5224_tx
IBM 5224 models 1 and 2, matrix
printer
5225_tx
IBM 5225 models 1 through 4, matrix
printer
5256_tx
IBM 5256 models 1 through 3, matrix
printer
4230_tx
IBM 4230 model 101 matrix printer
5x27_002_TX_KS
5x27 002 Twinax printer: Korean (KS)
5x27_002_ TX_KSSM
5x27 002 Twinax printer: Korean
(KSSM)
5x27_001_ TX
5x27 001 Twinax printer: Japanese
5x27_005_TX
5x27 005 Twinax printer: Chinese
The following tables describe the valid system languages that can be
used in coax and twinax mode.
263
264
Section 17: IBM Print Formatting
AXIS 5570e/AXIS 5670e User’s Manual
Coax mode
Mainframe
Parameter Name
SYSL
Default
37 US English
Value
Description
Value
User defined system language
*37
US English, Portuguese Alternate and Canadian Bilingual
833
Korean (Jamo)
256
International Set 1
836
Chinese
260
Canadian French
838
Thai
273
Austrian/German
870
East Europe
274
Belgian
871
Icelandic
275
Brazilian
892
OCR-A
277
Danish/Norwegian
893
OCR-B
278
Swedish/Finnish
1140
US English (Euro)
280
Italian
1141
Austrian German (Euro)
281
Japanese English
1142
Danish/Norwegian (Euro)
282
Portuguese
1143
Swedish/Finnish (Euro)
284
Spanish
1144
Italian (Euro)
285
UK English
1145
Spanish (Euro)
286
Austrian/German Alternate
1146
UK English (Euro)
2879
Danish/Norwegian Alternate
1147
French (Euro)
288
Swedish/Finnish Alternate
1148
International Set 5 (Euro)
289
Spanish Alternate
1149
Icelandic
290
Japanese
USER
User defined
293
APL
297
French
340
OCR
361
International Typographic
500
International set 5
AXIS 5570e/AXIS 5670e User’s Manual
Section 17: IBM Print Formatting
Twinax mode
AS/400
Parameter
Name
SYSL
Default
37 US English
Value
Description
Value
User defined system language
37
US English, Portuguese Alter-nate and
Canadian Bilingual
281
Japanese English
256
New Spanish Word Processing
282
Portuguese
273
Austrian/German
284
Spanish and Spanish Speaking
274
Belgian
285
UK English
275
Brazilian
297
French Azerty
277
Danish/Norwegian
500
Internat. Set 5 & Swiss Bilingual
278
Swedish/Finnish
871
Icelandic
280
Italian
USER
Notes:
Page Formats
•
For other languages the USER language can be used and edited.
•
To find out which system language you are running type:
DSPSYSVAL SYSVAL(QCHRID) on the command line and press
Enter. The Code page value is the value of the system language (see the
table above).
•
Visit the Axis web site http://www.axis.com/ for more information on how
to edit the character translation tables
You can configure the formats for each paper bin separately from the
AXIS 5570e/AXIS 5670e internal web pages.
Click admin | IBM Emulators | Detailed View for SCS/3270DS
Common Emulator Settings. Select the Page Format tab to configure
the parameters described below. Click OK at the bottom of the page
to save your settings to the print server.
265
266
Section 17: IBM Print Formatting
Paper Size
The parameters take two values, orientation and paper size. The
following tables describe the paper sizes that can be used in coax and
twinax mode.
Parameters
BIN1 - BIN 6,
MANUAL,
ENVELOPE,
CONTINUOUS
Paper Orientation
AXIS 5570e/AXIS 5670e User’s Manual
Default
LETTER
Printer Emulation
Options
Printer Description
EXEC
7.25 × 10.5 inches
LETTER
8.5
× 11 inches
LEGAL
8.5
× 14 inches
A4
210 × 297 mm
(8.27 ◊ 11.69 inches)
A3
297 × 420 mm
(11.69 ◊ 16.54 inches)
B4
250 × 353 mm
(10.12 ◊ 14.33 inches)
MON
3.8 × 7.5 inches (Monarch
envelopes)
C10
4.1 × 9.4 inches (COM-10
envelopes)
DL
4.3 × 8.6 inches
(DL envelopes)
CUSTOM
User defined size (see AXIS
Network Print Server Technical
Reference for details)
The following table describes the valid paper options:
Parameters
BIN1 - BIN 6,
MANUAL,
ENVELOPE,
CONTINUOUS
Default
COR
Printer Emulation
Options
Printer Description
COR
Computer Output Reduction
(COR) is enabled.
PORT
Use portrait as default print
orientation.
LAND
Use landscape as default print
orientation
AXIS 5570e/AXIS 5670e User’s Manual
Section 17: IBM Print Formatting
Notes:
COR printouts require a Laser Printer with the following characteristics:
ASCII Printer Driver
•
Landscape orientation
•
Vertically compressed to 70%
•
Horizontally compressed by using a font of higher character density
•
Top and left margins of 0.5 inches each by default
This parameter should match the printer type you have connected to
your AXIS 5570e/AXIS 5670e. Select the correct printer type from the
AXIS 5570e/AXIS 5670e internal web pages.
Click admin | IBM Emulators | Detailed View for SCS/IPDS Emulator
Configuration. Select the desired emulator tab and scroll down to the
Printer Driver parameter. Click OK at the bottom of the page to save
your settings to the print server.
The table below describes the available printer emulation options:
Parameter
PRDRIVER
Default
Printer Emulation
Options
Printer Description
GENERIC
Generic Printer Driver
PCL5
PCL5 printer
PCL4
PCL4 printer
IBM_PRO
IBM Proprinter
EPSON_FX
Epson FX
EPSON_LQ
Epson LQ
USER
Editable Printer Driver
Epson 15
Epson FX 15 CPI
PCL5
Notes:
If you wish to edit the control sequences within a printer driver, the USER driver
must be selected. See AXIS Technical Reference on www.axis.com
267
268
Section 18: IPDS Overview
Section 18
AXIS 5570e/AXIS 5670e User’s Manual
IPDS Overview
This section describes:
•
IPDS parameter settings
•
IPDS fonts
IPDS Parameter Settings
Before printing IPDS data streams, the basic parameters should be
set. This is done from the AXIS 5570e/AXIS 5670e web pages under
IBM Emulators | Detailed view (IBM IPDS Emulator Settings) where
you can configure the common parameters of the IPDS emulator and
IBM Emulators | Detailed view (SCS/IPDS Emulator Configurations)
where you can configure the settings for each session.
IPDS System Languages
The AXIS 5570e/AXIS 5670e must be set up for the System Language
of your IBM system configuration in order to obtain the correct
characters in each specific language. This is done from the IBM
Emulators | Detailed view (SCS/IPDS Emulator Configurations) page.
The default selection is US English (Code Page 37).
The following table describes the valid IPDS system languages:
AXIS 5570e/AXIS 5670e User’s Manual
Section 18: IPDS Overview
Code page
System language
*37
US English, Portuguese Alternate and Canadian Bilingual
256
International set 1
259
Symbols set 7
260
Canadian French
273
Austrian/German
274
Belgian
275
Brazilian
277
Danish/Norwegian
278
Swedish/Finnish
280
Italian
281
Japanese English
282
Portuguese
284
Spanish and Spanish Speaking
285
UK English
286
Austrian/German Alternate
287
Danish/Norwegian Alternate
288
Swedish/Finnish Alternate
Code page
System language
289
Spanish Alternate
290
Japanese-Katakana
293
APL
297
French Azerty
361
International Typographic
420
Arabic Bilingual
423
Greek 183
424
Hebrew
437
Multinational
500
Internationa, Set 5 & Swiss Bilingual
803
Hebrew Character Set A
870
Latin 2 Multilingual
871
Icelandic
880
Cyrillic Multilingual
892
OCR-A
893
OCR-B
1026
Latin 5
269
270
Section 18: IPDS Overview
AXIS 5570e/AXIS 5670e User’s Manual
The Euro character is implemented in the Code Pages 1140 - 1149:
Code page
System language - Latin 1 EBCDIC Publishing
1140
US English, Canadian English, Canadian French,
Netherlands, Brazil, Portugal
1141
Austrian, German
1142
Danish, Norwegian
1143
Finnish, Swedish
1144
Italian
1145
Castilian Spanish, Latin, American Spanish
1146
UK English
1147
French
1148
Multinational ECECP, Belgian, French, Belgian Dutch,
Switzerland
1149
Icelandic
Code page
System language - Latin 1 ASCII
858
Multinational PC with Euro
860
Portuguese (Primary = 850)
861
Icelandic (Primary = 850)
863
Canadian French (Primary = 850)
865
Nordic (Primary = 850)
1004
IBM PC Desktop Publishing
819
ISO Latin 1
1252
Windows Latin 1
AXIS 5570e/AXIS 5670e User’s Manual
Section 18: IPDS Overview
Code page
System language - Latin 2/3/4/5 EBCDIC and ASCII
852
Croatian, Czech, East German, Hungarian, Polish,
Romanian, Slovak, Slovenian
912
Latin 2 ISO/ ANSI 8 Bit
853
Latin 3 Multilingual PC
905
Latin 3 Multilingual
1069
Latin 4 EBCDIC
914
Latin 4 ISO/ASCII
857
Latin 5 PC
920
Latin 5 ISO/ANSI 8 Bit
1026
Latin 5
Code page
System language - Latin 9 EBCDIC and ASCII
923
Latin 9
924
Latin 9 EBCDIC
271
272
Section 18: IPDS Overview
IPDS Configuration
AXIS 5570e/AXIS 5670e User’s Manual
The basic IPDS parameters are set from the IBM Emulators | Detailed
view (IBM IPDS Emulator Settings) page:
Enter the configuration settings for the parameters described below.
When you are finished, click OK at the bottom of the page to save
your settings to the print server.
True Color Support
The Color Support setting determines how color information is to be
interpreted. Enabled means that color commands are sent to the
printer. Disabled means that color information is converted to blackand-white patterns.
The default setting is Disabled.
Duplex Support
The Duplex Support setting determines whether duplex support for
the attached printer shall be reported to the host. Enabled means
that duplex commands are transferred to the printer. Disabled means
that duplex printing is not supported. The default setting is Disabled.
AXIS 5570e/AXIS 5670e User’s Manual
Optimize Duplex
Section 18: IPDS Overview
Use this option to optimize duplex print jobs. Optimization means
that sheets are printed in simplex if the reverse side of the sheet is
empty, resulting in higher throughput.
Important:
Some printers will internally turn the sheet upside down when duplex is used.
This may cause undesired effects when using pre-printed forms. Setting this
parameter to No will force the entire job to be printed in duplex mode
N-up
Default output bin
The N-up parameter defines if 1, 2 or 4 pages in your document are
to be printed on each physical page.
This selection defines which output paper bin should be used as
default.
The default selection is Bin 1.
Default input bin
This selection defines which input paper bin should be used as
default.
The default selection is Bin 1.
IPDS bin 1-5
The physical paper size selection must match the actual paper size
you are using for Bin 1-5. The predefined sizes are Statement, Ledger,
Folio, Hagaki, Executive, Letter, Legal, A4 and A3.
The default size is A4.
If you are using another paper format, select Custom. This selection
requires that you define the paper size by setting the parameters
Physical Paper Width and Physical Paper Length to the appropriate
values.
IPDS PostScript
Configuration
Click the IPDS PostScript Driver Settings tab and enter the
configuration settings for the parameters as described below. When
you are finished, click OK at the bottom of the page to save your
settings to the print sever.
273
274
Section 18: IPDS Overview
Loaded Font
Smoothing
AXIS 5570e/AXIS 5670e User’s Manual
A downloaded 240 dpi font may appear jagged when printed on a
300 dpi printer. The AXIS 5570e/AXIS 5670e uses a font smoothing
feature to enhance the appearance of these fonts. The font
smoothing may be disabled if you want to speed up the font loading
or if your printer has insufficient PostScript virtual memory.
Loaded font smoothing is Enabled by default.
Note:
Font smoothing is optimized for printers with 300 dpi resolution. If your printer
has a resolution of 600 dpi or higher, the smoothing effect will be less significant.
In these cases we recommend that you disable the font smoothing to avoid
reduction in the performance.
PostScript Error
Handler
Use this parameter to download a PostScript Error Handler to the
printer at power on. Once downloaded, the Error Handler will print an
error message if a PostScript error occurs.
The Error Handler is Disabled by default.
Optimize Overlays
Virtual
Memory Kb
Enabling this parameter will activate an overlay optimization feature
resulting in faster throughput when using host downloaded overlays.
Enabling this feature will require more free Postscript Virtual Memory
in the printer.
This value defines how much memory the AXIS 5570e/AXIS 5670e
can use in the PostScript printer for storing resources.
The default value is 2000 kbytes.
PostScript
bin 1-5
PostScript
output bin settings
Map each PostScript bin (1-5) to a bin number or choose Default.
Enter the desired values in the Horizontal scale factor, Vertical scale
factor, Horizontal offset and Vertical offset fields.
These parameters are for mapping the IPDS bin numbers to the bin
numbers of the connected postscript printer.
AXIS 5570e/AXIS 5670e User’s Manual
Section 18: IPDS Overview
IPDS PCL
Configuration
Click the IPDS PCL Driver Settings tab and enter the configuration
settings for the parameters as described below. When you are
finished, click OK at the bottom of the page to save your settings to
the print sever.
Language version
Select the correct PCL language version depending on your connected
printer.
Symbol set
Select the preferred symbol set from the drop-down list. The default
and recommended value is AUTOMATIC. The print server will
automatically select the appropriate symbol set.
PCL bin 1-5
Define the positioning by setting the parameters Horizontal Offset
and Vertical Offset to the desired values.
PCL Output Bin
These parameters are for mapping the IPDS bin numbers to the bin
numbers of the connected PCL printer.
275
276
Section 18: IPDS Overview
AXIS 5570e/AXIS 5670e User’s Manual
IPDS Fonts
This section describes how IPDS fonts are handled by the AXIS
5570e/AXIS 5670e. There are two different approaches to font
handling:
•
downloading fonts from the host.
•
using fonts that are already resident in the printer.
Both methods are supported by the AXIS 5570e/AXIS 5670e.
Host Downloaded
fonts
IPDS provides functions for downloading fonts from the host
computer. The font resolutions of 240, 300 and 600 dpi are
automatically converted by AXIS 5570e/AXIS 5670e to the resolution
of the attached printer.
AS/400 downloaded fonts requires [AFP = *YES] in the AS/400 device description.
Printer Resident Fonts
The rest of this section deals with printer resident fonts. The nonstandard PostScript fonts are resident in the AXIS 5570e/AXIS 5670e
(OCR-B is one example), so you do not need font cards etc. to use the
listed fonts.
In IPDS mode, printer resident fonts can be selected by the system
referring to the FGID (Font Global IDentifier) and FW (Font Width).
AXIS 5570e/AXIS 5670e supports a large set of resident fonts.
Note:
(IBM Mainframe only) For PSF systems, resident fonts need to be mapped to the
host font name and code page. In PSF/MVS, this is done using the APSRMARK
utility and in PSF/VM using the APRFTBLV (RSCS) or APRFTIDB files. For more
information, refer to the PSF/MVS and PSF/VM manuals.
AXIS 5570e/AXIS 5670e User’s Manual
Section 18: IPDS Overview
The FGIDs are grouped according to the following table:
FGID (hex)
FGID (dec)
TYPE
0001 - 0041
1 -65
0042 - 0099
66 - 153
12 CPI
009A - 00C8
154 - 200
Proportional PSM
00C9 - 00D2
201 - 210
13 CPI
00D3 - 00EF
208 - 239
15 CPI
00F0 - 00F7
240 - 247
5 CPI
00F8 - 0103
248 - 259
17 CPI
0104 - 0111
260 - 273
8 CPI
0112 - 0117
274 - 279
17 CPI
0118 - 011B
280 - 283
20 CPI
011C - 0120
284 - 288
25 CPI
0121 - 012B
289 - 299
27 CPI
012C - 01FF
300 - 511
10 CPI
FGID (hex)
FGID (dec)
10 CPI
TYPE
0200 - 0EFF
512 - 3839
Typographic
0F00 - 0FFF
3840 - 4095
User Defined Fonts
1000 - FFFE
4096 - 65534
Typographic
The AXIS 5570e/AXIS 5670e supports extended font mapping at
PostScript level, making it possible to redefine any of the FGIDs.
Immediate Font Substitutions
Certain FGIDs will be immediately substituted by the AXIS
5570e/AXIS 5670e. The substitution table depends on the selected
IBM printer emulation.
Unsupported Fonts
A selection of an unsupported FGID value will result in a substitution
to a default font. The AXIS 5570e/AXIS 5670e uses the same default
fonts as the emulated IBM printers.
277
278
Section 18: IPDS Overview
AXIS 5570e/AXIS 5670e User’s Manual
Typographical Fonts
This section deals with font width selections for typographical
(proportional pitch) fonts.
Note that when an unsupported typographical font (FGID range 512 65534) is selected, the resulting font will be a fixed pitch and the
selected font width value will be ignored.
Default Font Width
When the default font width is selected, the AXIS 5570e/AXIS 5670e
will set a font width in one of the following ways depending on the
selected IBM printer emulation:
IBM 4028/4332
The font width is set to 67 (corresponding to a 10 point font).
IBM 3812/3816
The font width is set to the smallest available value for the selected
FGID. For FGID 16951 (Century Schoolbook), the resulting font width
is 102 (12 points), and for FGID 5687 (Times Roman), the resulting
font width is 40 (6 points).
Scalable Fonts
If the selected font width (point size) is not available for the selected
FGID, the AXIS 5570e/AXIS 5670e will set a point size in one of the
following ways depending on the font:
Times Roman,
Helvetica
and Century
Schoolbook
The font width value is converted to a point size used to dynamically
scale the selected font. This means that you have a completely free
choice of point sizes (only limited by the host application) when
printing with these fonts.
Any other
typographical font
The nearest smaller available font width for the selected FGID will be
used. If a smaller font width is not available, the nearest larger font
width will be used.
AXIS 5570e/AXIS 5670e User’s Manual
Section 19
Section 19: DBCS Support
DBCS Support
The AXIS 5570e/AXIS 5670e supports Double-Byte Character Set
(DBCS) for SNA and TN5250E printing. This facilitates printing from
an IBM AS/400 host system for languages employing double-byte
character sets.
The following Chinese, Japanese and Korean DBCS tables are used in
the AXIS 5570e/AXIS 5670e:
Country
Printer Emulation
Character Table
Korea (KS)
5x27_002_TX_KS
KS
Korea (KSSM)
5x27_002_TX_KSSM
KSSM
Japan
5x27_001_TX
Shift - JIS
China
5x27_005_TX
GB
AXIS 5570e/AXIS 5670e Double-byte Character Tables
Important!
The AXIS 5570e/AXIS 5670e supports SNA DBCS printing in IBM 5494
emulation only.
Configuring the AS/400 Host, 5494 CU mode
Follow the instructions below to configure the AS/400 Host for DBCS
support:
1. Type WRKSYSVAL on the AS/400 command line and press Enter.
2. Check that the DBCS version installed indicator (QIGC) sysval is
set to 1 (on).
3. Check that the QIGCCDEFNT sysval is set to a DBCS font installed
in the system.
4. Proceed with the steps detailed in The AS/400 Host System
Checklist, on page 37.
279
280
Section 19: DBCS Support
AXIS 5570e/AXIS 5670e User’s Manual
Configuring the AXIS 5570e/AXIS 5670e
A number of printer emulations exist for DBCS printing. To set the
correct system language and printer driver, refer to the tables below
and enter the values in the IBM Configuration Wizard.
Country
Printer Emulation
System Language
Korea (KS)
5x27_002_TX_KS
833
Korea (KSSM)
5x27_002_TX_KSSM
833
Japan
5x27_001_TX
290
China
5x27_005_TX
836
Printer Emulation and System Language for Country options
Country
PCL Printer Driver
Korea (KS)
Epson LQ KS
Korea (KSSM)
Japan
Matrix Printer Driver
None
PCL5
None
China
Epson LQ 1600K
Taiwan
Epson LQ 1600K
1. Start a Web browser, e.g. Internet Explorer or Netscape
Navigator.
2. Enter the IP address or the host name of the AXIS 5570e/AXIS
5670e in the location field and press the Enter key on your
keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e
will appear.
AXIS 5570e/AXIS 5670e User’s Manual
Section 19: DBCS Support
Important:
To protect the admin pages and the Configuration Wizard from unauthorized use,
enter a password (default Pass) in the Root Password field under admin | General
Settings.
3. Click the Configuration Wizard for IBM sessions button.
4. Click the Add Session button. This will start the Configuration
Wizard which is a step-by-step guide through the required IBM
configuration settings.
Note:
Default fonts will be changed when switching printer emulations.
Verifying the Communications Link
Having configured the AS/400 host AXIS 5570e/AXIS 5670e in
accordance with the above, verify that the communications link is
functioning correctly by following instructions 1-4 detailed in
Verifying the Communication Link, on page 47.
281
282
Section 19: DBCS Support
AXIS 5570e/AXIS 5670e User’s Manual
Amending Device Features
After automatic setup, it may be necessary to change the Device
features and Last Code Point of the printer device. Failure to do so
may cause corruption within your print data.
Follow the instructions below, to set the appropriate Device features
and Last Code Point for your chosen printer device:
1. Make sure that the writer is stopped by typing ENDWTR
xxxxPRT01 on the AS/400 command line, where xxxxPRT01
is the printer device name. Press ENTER.
2. Type VRYCFG CFGOBJ(xxxxPRT01) CFGTYPE(*DEV)
STATUS(*OFF) to vary off the printer device, where
xxxxPRT01 is the printer device name. Press ENTER.
3. Type CHGDEVPRT xxxxPRT01 to change the printer device
name, where xxxxPRT01 is the printer device name. Press F4.
4. Under DBCS Feature (IGCFEAT) amend the Device Features and
Last Code Point to the appropriate value corresponding to the
country language.
Country
Device features
Last Code Point
Korea
2424K1
D3FE
Japan
2424J1
68FE
China
2424S1
6FFE
Device features and Last Code Point for Country options
5. Type VRYCFG CFGOBJ(xxxxPRT01) CFGTYPE(*DEV)
STATUS(*ON) on the AS/400 command line to vary on the
printer device, where xxxxPRT01 is the printer device name.
Press ENTER.
6. Type STRPRTWTR xxxxPRT01 to start the Writer, where
xxxxPRT01 is the printer device name. Press ENTER.
7. Direct a printout to this printer device to confirm that the above
changes have been implemented correctly.
AXIS 5570e/AXIS 5670e User’s Manual
Section 19: DBCS Support
Extended IBM Printer Emulation
Extended emulation will only work in SBCS mode. Before entering
extended emulation you will have to change to single byte mode by
sending shift in.
<SI>(SCS Shift In Control Code)
%CONFIG+
SAVE;
%CONFIG<SO>(SCS Shift Out Control Code)
Example (with DBCS mode before entering extended emulation)
Font Tables
The following tables define the DBCS font types supported in the
AXIS 5570e/AXIS 5670e (5494 CU Mode):
DBCS FONTS (Japan)
DBCS FONTS (China)
FGID
IBM Font Name
FGID
IBM Font Name
50000
MS Mincho
10 CPI
50100
SimSun
10 CPI
50001
MS Mincho
10 CPI
50101
SimSun
10 CPI
50014
MS Mincho
10 CPI
50114
SimSun
10 CPI
50002
MS Mincho
12 CPI
50102
SimSun
12 CPI
50015
MS Mincho
12 CPI
50115
SimSun
12 CPI
50003
MS Mincho
13.3 CPI
50103
SimSun
13.3 CPI
50016
MS Mincho
13.3 CPI
50116
SimSun
13.3 CPI
50007
MS Mincho
14.3 CPI
50107
SimSun
14.3 CPI
50008
MS Mincho
14.3 CPI
50108
SimSun
14.3 CPI
50019
MS Mincho
14.3 CPI
50119
SimSun
14.3 CPI
50004
MS Mincho
15 CPI
50104
SimSun
15 CPI
283
284
Section 19: DBCS Support
AXIS 5570e/AXIS 5670e User’s Manual
50005
MS Mincho
15 CPI
50105
SimSun
15 CPI
50017
MS Mincho
15 CPI
50117
SimSun
15 CPI
50009
MS Mincho
17.1 CPI
50109
SimSun
17.1 CPI
50020
MS Mincho
17.1 CPI
50120
SimSun
17.1 CPI
50006
MS Mincho
18 CPI
50106
SimSun
18 CPI
50018
MS Mincho
18 CPI
50118
SimSun
18 CPI
50010
MS Mincho
18.9 CPI
50110
SimSun
18.9 CPI
50021
MS Mincho
18.9 CPI
50121
SimSun
18.9 CPI
500111
MS Mincho
21.5 CPI
50111
SimSun
21.5 CPI
50012
MS Mincho
21.5 CPI
50112
SimSun
21.5 CPI
50022
MS Mincho
21.5 CPI
50122
SimSun
21.5 CPI
50013
MS Mincho
25.7 CPI
50113
SimSun
25.7 CPI
50023
MS Mincho
25.7 CPI
50123
SimSun
25.7 CPI
DBCS FONTS (Korea KS)
DBCS FONTS (Korea KSSM)
FGID
IBM Font Name
FGID
IBM Font Name
50030
HanYang
10 CPI
50130
Compst
10 CPI
50031
HanYang
10 CPI
50131
Compst
10 CPI
50044
HanYang
10 CPI
50144
Compst
10 CPI
50032
HanYang
12 CPI
50132
Compst
12 CPI
50045
HanYang
12 CPI
50145
Compst
12 CPI
50033
HanYang
13.3 CPI
50133
Compst
13.3 CPI
50046
HanYang
13.3 CPI
50146
Compst
13.3 CPI
50037
HanYang
14.3 CPI
50137
Compst
14.3 CPI
AXIS 5570e/AXIS 5670e User’s Manual
Section 19: DBCS Support
50038
HanYang
14.3 CPI
50138
Compst
14.3 CPI
50049
HanYang
14.3 CPI
50149
Compst
14.3 CPI
50034
HanYang
15 CPI
50134
Compst
15 CPI
50035
HanYang
15 CPI
50135
Compst
15 CPI
50047
HanYang
15 CPI
50147
Compst
15 CPI
50039
HanYang
17.1 CPI
50139
Compst
17.1 CPI
50050
HanYang
17.1 CPI
50150
Compst
17.1 CPI
50036
HanYang
18 CPI
50136
Compst
18 CPI
50048
HanYang
18 CPI
50148
Compst
18 CPI
50040
HanYang
18.9 CPI
50140
Compst
18.9 CPI
50051
HanYang
18.9 CPI
50151
Compst
18.9 CPI
50041
HanYang
21.5 CPI
50141
Compst
21.5 CPI
50042
HanYang
21.5 CPI
50142
Compst
21.5 CPI
50052
HanYang
21.5 CPI
50152
Compst
21.5 CPI
50043
HanYang
25.7 CPI
50143
Compst
25.7 CPI
50053
HanYang
25.7 CPI
50153
Compst
25.7 CPI
285
286
Section 20: Digital Copier Support
Section 20
AXIS 5570e/AXIS 5670e User’s Manual
Digital Copier Support
The logical printers support the printing options available on digital
copiers and multi-functional printers. It is recommended that you
configure the eight logical printers (PR1-PR8) to allow for eight
different combinations of the following options to suit your printing
needs.
For more information on how to configure the logical printers, please
refer to Logical Printers for Customized Printing, on page 220.
The added functionality includes the following options:
Copier Model
From the drop-down list of supported copiers, select the digital
copier that you have connected the AXIS 5470e to.
Copier Duplex
The AXIS 5470e supports duplex printing i.e. printing on both sides of
the paper. The options in the drop-down list are:
Copier Staple
•
Off i.e. the duplex printing option is not activated (default).
•
Simplex i.e. printing on one side only.
•
Long-edge binding i.e. printing on both sides, long-edge first.
•
Short-edge binding i.e. printing on both sides, short-edge first.
The AXIS 5470e supports stapling with the following options:
•
Off i.e. the stapling option is not activated (default).
•
Top left slant i.e. one staple in a slanted position in the top left
corner of the document.
•
Top left horizontal i.e. one staple placed horizontally in the top
left corner of the document.
•
Top left vertical i.e. one staple placed vertically in the top left
corner of the document.
•
Top 2 i.e. two staples at the top of the document.
AXIS 5570e/AXIS 5670e User’s Manual
Copier Hole Punch
Copier Paper Source
Copier Copies
Section 20: Digital Copier Support
•
Left 2 i.e. two staples on the left hand side of the document.
•
Center 2 i.e. two staples set in the center of the page. This option
is intended for documents printed in A3 format. The staples are
placed in the center of the page where the document is to be
folded. Please refer to the documentation of your digital copier
for more information on these features.
The AXIS 5470e supports hole punching with the following options:
•
Off i.e. the hole punching option is not activated (default).
•
Long-edge i.e. the left hand side of the document.
•
Short-edge i.e. the top of the document.
Enter the desired input bin i.e. paper tray on your digital copier
Enter how many collated (sorted) copies you wish to print in the
Copies field.
Note:
If you experience problems with this functionality the Digital Copier printing
options may have been set inconsistently. Please check your configuration
settings and try again.
287
288
Section 21: Test Button
Section 21
AXIS 5570e/AXIS 5670e User’s Manual
Test Button
The test button is located on the front right hand side of the AXIS
5570e/AXIS 5670e and is used for:
•
Printing a test page, checking the connection to the printer.
•
Printing a parameter list, showing the AXIS 5570e/AXIS 5670e
current settings.
•
Resetting the AXIS 5570e/AXIS 5670e parameters to the factory
default settings.
The Test Page
Press the test button once to print a test page. If the test page prints,
the parallel interface is functioning correctly. The printed Test Page
contains basic information about the AXIS 5570e/AXIS 5670e. It is
recommended that you print a test page every time you have
connected the AXIS 5570e/AXIS 5670e to a printer.
The Parameter List
Press the test button twice to print a parameter list showing the
current AXIS 5570e/AXIS 5670e settings. This list provides
comprehensive details of all the parameters and their current status.
Refer to The Parameter List, on page 295.
If you want to change any of the parameters, use one of the methods
that are described in Management and Configuration, on page 180.
Performing a Factory
Default
Follow the instructions below to reset the AXIS 5570e/AXIS 5670e to
the factory default settings:
1. Remove the external power supply to switch off the AXIS
5570e/AXIS 5670e.
2. Press and hold down the test button, while you reconnect the
external power supply.
3. Continue to hold down the test button until the network
indicator remains constantly lit. This should take about 20
seconds.
AXIS 5570e/AXIS 5670e User’s Manual
Section 21: Test Button
4. Restart the AXIS 5570e/AXIS 5670e by disconnecting and
reconnecting the external power supply.
Important!
All parameters are reset to their default values when performing a factory
default with the test button.
Installed certificates and keys are not affected by a factory default.
289
290
Section 22: Technical Specifications
Section 22
AXIS 5570e/AXIS 5670e User’s Manual
Technical Specifications
Refer to the ‘Parameter List’ document on www.axis.com for a
complete description of the Axis print server parameters.
Supported Printers:
IBM Capabilities
Support for all printers and copiers except host-based printers such
as Windows GDI.
IBM Mainframe (zSeries):
• OS: IBM S/370, S/390, 30xx, 43xx, 47xx, 937x, 81xx
• TCP/IP based protocols: TN3270E, PPR/PPD, LPR/LPD and RawTCP
• SNA support: LU1 and LU3 (node type 2.0) for IBM 3174 Control
unit emulation
• Data streams: IPDS, SCS, 3270DS as well as PostScript, PCL and
ASCII
• Emulated printers: 4332, 4028, 3812 model 2, 3816 model 01S and
01D, 4224, 4230, 3287, 3268, 4214 and 3262
IBM AS/400 (iSeries):
• OS: IBM OS/400
• TCP/IP based protocols: TN5250E, PPR/PPD, LPR/LPD and RawTCP.
• SNA support: LU6.2 (node type 2.1) for IBM 5494 Control unit
emulation
• Data streams: IPDS, SCS as well as PostScript, PCL and ASCII
• Emulated printers: 4332, 4028, 3812, 3816, 4214-2, 5224, 5225,
5256, 4230, 5x27-2 KS, 5x27-3 KSSM, 5x27-3 and 5x27-5
AXIS 5570e/AXIS 5670e User’s Manual
Supported systems:
Section 22: Technical Specifications
• Microsoft Windows: 98, Me, NT, 2000, XP and 2003 Server
• Novell NetWare: 3.X, 4.X, 5.X, 6.X. Supports bindery and NDS mode.
Supports user messages and printer status. NDPS supported over IP
and IPX. Support for iPrint using both LPR and IPP protocols. PSERVER
(IP/IPX), RPRINTER/NPRINTER supported
• Apple MacOS 7, 8, 9, MacOS X version 10.X
• All Unix systems supporting TCP/IP (Linux, BSD, System V, Solaris,
HP-UX, IBM AIX, Silicon Graphics IRIX, etc.)
• Other systems supporting TCP/IP: IBM (MVS, VM, VSE, OS/400),
DEC, VMS
• Microsoft LAN Manager
• IBM LAN Server
• LANtastic
Supported web
browsers
Supported Protocols:
Any standard web browser (Netscape 4.x or higher and MS Internet
Explorer 4.x or higher)
• TCP/IP: ARP, DHCP, BOOTP, RARP, DNS, DDNS, Telnet, TFTP, FTP,
LPR, Reverse Telnet, PROS, IPP, IP, TCP, UDP, HTTP, HTTPS, SSL/TLS,
SNMP, SLP v1/v2, ICMP, IGMP
• NetWare: IPX, SPX, SAP, NCP (extended with NDS), NDPS, NLSP, LIP,
RIP, RIP-II, OSPF
• Apple EtherTalk: AAPR, ATP, DDP, NBP, PAP,RTMP, ZIP
• NetBIOS/NetBEUI
Logical Printers
Logical printer ports can be programmed to perform auto ASCII to
PostScript conversion, add string before and after job, string
substitution, alternative output and character set conversion.
291
292
Section 22: Technical Specifications
AXIS 5570e/AXIS 5670e User’s Manual
Copiers
Each logical printer port can be configured to activate a number of
finishing options in the digital copier. Please visit the support pages
at www.axis.com for a list of supported copiers.
Security
• Password protected configuration
• SSL/TLS support for HTTPS secure management
• NetWare: Encrypted passwords, NetWare
Packet Signature Level 1, 2, 3
• Option to disable insecure protocols
Print Server
Management
• AXIS ThinWizard for installation, configuration, monitoring and
firmware upgrading of multiple units
• Internal web pages for installation, configuration, monitoring and
firmware upgrading
• SNMP-MIB II compliant (RFC 1213), Axis private enterprise MIB
included
• Netware: full PCONSOLE, NWAdmin, ConsoleOne and iPrintiManager support
Firmware Upgrade
Firmware upgrade using AXIS ThinWizard, the print servers web pages
or FTP
Network Connection
All standard Ethernet and Fast Ethernet networks: RJ-45 connector
(Category 5 or 6, shielded twisted pair cable) for 10baseT or 100base
TX Ethernet with full duplex.
Supports:
• IEEE802.2, IEEE802.3, SNAP and Ethernet II frame types
simultaneously.
• NWay for auto-detection of network speed
AXIS 5570e/AXIS 5670e User’s Manual
Printer Connection
Section 22: Technical Specifications
• Parallel: 36-pin Centronics connector, highspeed IEEE 1284
compliant with ECP support and throughput of 1 MB/sec
• USB: USB 1.1 Low and Full speed. Successfully tested with USB 2.0
Printers
• Serial: 9-pin DSUB connector, RS-232, XON/ XOFF or RTS/CTS, data
rates up to 115.200 baud
• Bi-directional support for Apple EtherTalk,
• Reverse Telnet and PROS
Hardware:
• Processor: AXIS Etrax 100LX 32-bit 100 MHz RISC
• Memory: 2 MB Flash, 8 MB RAM
Front Panel
• 2 LED indicators: Power and Network
• Test button for information printouts
Power Consumption
Dimensions:
Power provided by external supply. Maximum 5.6W (Type PS-H, 5.1
VDC 2000mA)
• AXIS 5570e:
Height: 2.9 cm/1.1 in,
Width: 6.2 cm/2.4 in,
Depth: 11.7 cm/4.6 in,
Weight: 0.081 kg/ 0.18lb
• AXIS 5670e:
Height: 2.9 cm/1.1 in,
Width: 16.0 cm/6.3 in,
Depth: 12.9 cm/5.1 in,
Weight: 0.28 kg/0.64 lb
Environmental
• Temperature: 40-105 °F (5-40 °C)
• Humidity: 10-90% non-condensing
293
294
Section 22: Technical Specifications
Approvals
AXIS 5570e/AXIS 5670e User’s Manual
• EMC: EN 55022/1998, EN 55024:1998, EN 61000-3-2, EN 610003-3, VCCI Class B, CTICK AS/NZS 3548, Compliance to FCC part 15
Subpart B, Class B
• Safety: EN 60950
AXIS 5570e/AXIS 5670e User’s Manual
Section 23
Section 23: The Parameter List
The Parameter List
This appendix provides an overview of the AXIS 5570e/AXIS 5670e
parameters. You can download the latest technical information on
www.axis.com
The Config File
The left-hand column shows the parameters (default values) as they
appear in the internal Web pages.
After you have changed them, most parameters take effect for the
next print job. If Requires Restart appears in a parameter description,
you must restart the AXIS 5570e/AXIS 5670e, before the new setting
for that parameter takes effect.
Please refer to Section 10 Management and Configuration, on page
180, for more information about how to change the parameters.
AXIS 5570e:
--- General Menu
NODE_ADDR. : 00 40 8C XX XX XX
NETWORK_SPEED. : AUTO_SENSE (AUTO_SENSE, 10_HALF_DX, 10_FULL_DX, 100_HALF_DX,
100_FULL_DX)
PS_NAME.
: AXISXXXXXX
ROOT_PWD.
: pass
SWUP_KEY.
:
USERS.
:
BASE_URL.
: www.axis.com
CHARSET.
: ISO-8859-1 (ISO-8859-1, UTF-8)
AXIS_PRINT_SYSTEM. : YES
RCONFIG_ENB. : YES
DEF_OUT.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1)
SYS_LOC.
:
SYS_CONT.
--- TN3270E
:
295
296
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
TN3270E_IR. : 0
TN3270E_1. : OFF, 0 0 0 0, 23, PR1, 1, AXPR1
TN3270E_2. : OFF, 0 0 0 0, 23, PR2, 2, AXPR2
TN3270E_3. : OFF, 0 0 0 0, 23, PR3, 3, AXPR3
TN3270E_4. : OFF, 0 0 0 0, 23, PR4, 4, AXPR4
TN3270E_5. : OFF, 0 0 0 0, 23, PR5, 5, AXPR5
TN3270E_6. : OFF, 0 0 0 0, 23, PR6, 6, AXPR6
TN3270E_7. : OFF, 0 0 0 0, 23, PR7, 7, AXPR7
TN3270E_8. : OFF, 0 0 0 0, 23, PR8, 8, AXPR8
--- TN5250E
TN5250E_KA. : YES
TN5250E_1. : OFF, 0 0 0 0, 23, PR1, 1, AXPR1, QSYSOPR, QSYS
TN5250E_2. : OFF, 0 0 0 0, 23, PR2, 2, AXPR2, QSYSOPR, QSYS
TN5250E_3. : OFF, 0 0 0 0, 23, PR3, 3, AXPR3, QSYSOPR, QSYS
TN5250E_4. : OFF, 0 0 0 0, 23, PR4, 4, AXPR4, QSYSOPR, QSYS
TN5250E_5. : OFF, 0 0 0 0, 23, PR5, 5, AXPR5, QSYSOPR, QSYS
TN5250E_6. : OFF, 0 0 0 0, 23, PR6, 6, AXPR6, QSYSOPR, QSYS
TN5250E_7. : OFF, 0 0 0 0, 23, PR7, 7, AXPR7, QSYSOPR, QSYS
TN5250E_8. : OFF, 0 0 0 0, 23, PR8, 8, AXPR8, QSYSOPR, QSYS
--- TCP/IP Menu
TCP_ENB.
: YES
INT_ADDR.
:0000
DEF_ROUT.
:0000
NET_MASK.
:0000
HTTPS_ENB. : NO
PROS_PWD.
: netprinter
PROS_PRT.
: 35
LPD_BANN.
: OFF (OFF, AUTO, LAST)
DHCP_ENB.
: NO
AUTOIP_ENB. : NO
BOOTP_ENB. : YES
AXIS 5570e/AXIS 5670e User’s Manual
RARP_ENB.
: YES
WINS_ENB.
: YES
Section 23: The Parameter List
WINS_ADDR1. : 0 0 0 0
WINS_ADDR2. : 0 0 0 0
NBT_SCOPE_ID. :
DNS_ENB.
: YES
DNS_ADDR1. : 0 0 0 0
DNS_ADDR2. : 0 0 0 0
DOMAIN_NAME. :
SLP_ENB.
: YES
SLP_SCOPE_LIST. : DEFAULT
SMTP_SERVER. :
FTP_ENB.
: YES
TELNET_ENB. : YES
DEFAULT_RAW_TCP. : 9100-9101 (9100-9101, CLOSED)
RTN_OPT.
: NO
RTN_PR1.
: 0, ASCII, 1
RTN_PR2.
: 0, ASCII, 2
RTN_PR3.
: 0, ASCII, 3
RTN_PR4.
: 5011, SCS, 4
RTN_PR5.
: 5012, SCS, 5
RTN_PR6.
: 5013, SCS, 6
RTN_PR7.
: 0, ASCII, 7
RTN_PR8.
: 0, ASCII, 8
DEF_IP_FRAME_TYPE. : EthernetII (EthernetII, SNAP)
--- SNMP Menu
SNMP_ENB.
: YES
SNMP_V1_CONFIG. : YES
READ_COM.
: public
WRT_COM.
: pass
TRAPADDR.
:0000
TRAP_COM.
: public
297
298
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
SYS_NAME.
:
SNMP_AUT.
: DISABLE (DISABLE, ENABLE)
TRAP_PRT.
: DISABLE (DISABLE, ENABLE)
--- NetWare Menu
NETW_ENB.
: YES
NETW_TRANSPORT_PROTOCOL. : DUAL_STACK (IPX_ONLY, IP_ONLY, DUAL_STACK)
NDPS.
: TCP_AND_SPX (TCP_AND_SPX, TCP_ONLY, SPX_ONLY, DISABLED)
JOB_CHECK_DELAY. : 5
CONF_CHECK_DELAY. : 300
FR_802_3.
: YES
FR_ETH_2.
: YES
FR_802_2.
: YES
FR_SNAP.
: YES
NCP_BURST_MODE. : YES
PSERVER_NDS_TREE. :
PSERVER_NDS_FILESERVER. :
PSERVER_NDS_DISTINGUISHED_NAME. :
PSERVER_BINDERY1. :
PSERVER_BINDERY2. :
PSERVER_BINDERY3. :
PSERVER_BINDERY4. :
PSERVER_BINDERY5. :
PSERVER_BINDERY6. :
PSERVER_BINDERY7. :
PSERVER_BINDERY8. :
PSERVER_BINDERY9. :
PSERVER_BINDERY10. :
PSERVER_BINDERY11. :
PSERVER_BINDERY12. :
PSERVER_BINDERY13. :
PSERVER_BINDERY14. :
PSERVER_BINDERY15. :
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
PSERVER_BINDERY16. :
NPRINTER1. :
NPRINTER2. :
NPRINTER3. :
NPRINTER4. :
NPRINTER5. :
NPRINTER6. :
NPRINTER7. :
NPRINTER8. :
--- NetBIOS/NetBEUI Menu
LSLM_ENB.
: YES
NB_FR_TYPE. : FR_802_2 (FR_AUTO, FR_802_2, FR_DIX)
LPRINT_1.
: AX181E6A.LP1
LLOGIC_1.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1)
LPRINT_2.
: AX181E6A.US1
LLOGIC_2.
: PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1)
LPRINT_3.
:
LLOGIC_3.
: PR3 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1)
LPRINT_4.
:
LLOGIC_4.
: PR4 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1)
LPRINT_5.
:
LLOGIC_5.
: PR5 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1)
LPRINT_6.
:
LLOGIC_6.
: PR6 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1)
LPRINT_7.
:
LLOGIC_7.
: PR7 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1)
LPRINT_8.
:
LLOGIC_8.
: PR8 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1)
299
300
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
--- AppleTalk Menu
ATLK_ENB.
: YES
ATK_ZONE.
:
ZONER_EN.
: YES
ATK_FONT.
: DEFAULT (DEFAULT, 35N, ALL)
AUTO_DT_PRIN. : NO
APRINT_1.
: AXIS181E6A_LPT1
ATYPE_1.
: LaserWriter
ALOGIC_1.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1)
BINARY_TYPE_1. : TBCP (TBCP, BCP, NONE)
APRINT_2.
: AXIS181E6A_USB1
ATYPE_2.
: LaserWriter
ALOGIC_2.
: PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1)
BINARY_TYPE_2. : TBCP (TBCP, BCP, NONE)
--- Printer1 Menu
PR1_OUT.
: LPT1 (NONE, LPT1, USB1)
PR1_NAME.
:
PR1_SCND.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR1_WAIT.
: YES
PR1_IN.
: AUTO (AUTO, NONE)
PR1_BEF.
:
PR1_STR.
:
PR1_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR1_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR1_AFT.
:
PR1_DUMP.
PR1_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR1_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR1_FORM.
: 66 0 100 60 30 50
PR1_FONT.
:
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
--- Printer2 Menu
PR2_OUT.
: USB1 (NONE, LPT1, USB1)
PR2_NAME.
:
PR2_SCND.
: PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR2_WAIT.
: YES
PR2_IN.
: AUTO (AUTO, NONE)
PR2_BEF.
:
PR2_STR.
:
PR2_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR2_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR2_AFT.
:
PR2_DUMP.
PR2_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR2_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR2_FORM.
: 66 0 100 60 30 50
PR2_FONT.
:
--- Printer3 Menu
PR3_OUT.
: LPT1 (NONE, LPT1, USB1)
PR3_NAME.
:
PR3_SCND.
: PR3 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR3_WAIT.
: YES
PR3_IN.
: AUTO (AUTO, NONE)
PR3_BEF.
:
PR3_STR.
:
PR3_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR3_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR3_AFT.
:
PR3_DUMP.
PR3_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR3_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR3_FORM.
: 66 0 100 60 30 50
301
302
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
PR3_FONT.
:
--- Printer4 Menu
PR4_OUT.
: USB1 (NONE, LPT1, USB1)
PR4_NAME.
:
PR4_SCND.
: PR4 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR4_WAIT.
: YES
PR4_IN.
: AUTO (AUTO, NONE)
PR4_BEF.
:
PR4_STR.
:
PR4_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR4_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR4_AFT.
:
PR4_DUMP.
PR4_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR4_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR4_FORM.
: 66 0 100 60 30 50
PR4_FONT.
:
--- Printer5 Menu
PR5_OUT.
: LPT1 (NONE, LPT1, USB1)
PR5_NAME.
:
PR5_SCND.
: PR5 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR5_WAIT.
: YES
PR5_IN.
: AUTO (AUTO, NONE)
PR5_BEF.
:
PR5_STR.
:
PR5_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR5_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR5_AFT.
:
PR5_DUMP.
PR5_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
PR5_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR5_FORM.
: 66 0 100 60 30 50
PR5_FONT.
:
--- Printer6 Menu
PR6_OUT.
: USB1 (NONE, LPT1, USB1)
PR6_NAME.
:
PR6_SCND.
: PR6 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR6_WAIT.
: YES
PR6_IN.
: AUTO (AUTO, NONE)
PR6_BEF.
:
PR6_STR.
:
PR6_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR6_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR6_AFT.
:
PR6_DUMP.
PR6_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR6_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR6_FORM.
: 66 0 100 60 30 50
PR6_FONT.
:
--- Printer7 Menu
PR7_OUT.
: LPT1 (NONE, LPT1, USB1)
PR7_NAME.
:
PR7_SCND.
: PR7 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR7_WAIT.
: YES
PR7_IN.
: AUTO (AUTO, NONE)
PR7_BEF.
:
PR7_STR.
:
PR7_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR7_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR7_AFT.
:
303
304
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
PR7_DUMP.
PR7_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR7_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR7_FORM.
: 66 0 100 60 30 50
PR7_FONT.
:
--- Printer8 Menu
PR8_OUT.
: USB1 (NONE, LPT1, USB1)
PR8_NAME.
:
PR8_SCND.
: PR8 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR8_WAIT.
: YES
PR8_IN.
: AUTO (AUTO, NONE)
PR8_BEF.
:
PR8_STR.
:
PR8_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR8_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR8_AFT.
:
PR8_DUMP.
PR8_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR8_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR8_FORM.
: 66 0 100 60 30 50
PR8_FONT.
:
--- LPT1 Menu
L1_CENTR.
: HISPEED (IBM_PC, STNDRD, FAST, HISPEED, HINOACK)
L1_BSYTM.
: 60
L1_MGM_INFO. : AUTO (DISABLE, AUTO)
L1_COMMENT. :
L1_BIDIR.
L1_READT.
: AUTO (DISABLE, AUTO)
:3
--- USB1 Menu
U1_MGM_INFO. : AUTO (DISABLE, AUTO)
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
U1_COMMENT. :
U1_BIDIR.
: AUTO (DISABLE, AUTO)
U1_READT.
:3
--- IBM EMULATOR 1
PREMUL1. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL1.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR1.
: NO
MPL1.
: 66, ENA
MPP1.
: 132, ENA
LPI1.
: 6 (3, 4, 6, 8)
CPI1.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI1.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI1.
: YES
LM1.
: 0, 0, 48
TM1.
: 26, 26, 74
LDSF1.
: 100, 100, 70
DEFBIN1.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER1. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 2
PREMUL2. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL2.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR2.
: NO
MPL2.
: 66, ENA
MPP2.
: 132, ENA
305
306
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
LPI2.
: 6 (3, 4, 6, 8)
CPI2.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI2.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI2.
: YES
LM2.
: 0, 0, 48
TM2.
: 26, 26, 74
LDSF2.
: 100, 100, 70
DEFBIN2.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER2. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 3
PREMUL3. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL3.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR3.
: NO
MPL3.
: 66, ENA
MPP3.
: 132, ENA
LPI3.
: 6 (3, 4, 6, 8)
CPI3.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI3.
AUTORI3.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
: YES
LM3.
: 0, 0, 48
TM3.
: 26, 26, 74
LDSF3.
: 100, 100, 70
DEFBIN3.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER3. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
--- IBM EMULATOR 4
PREMUL4. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL4.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR4.
: NO
MPL4.
: 66, ENA
MPP4.
: 132, ENA
LPI4.
: 6 (3, 4, 6, 8)
CPI4.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI4.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI4.
: YES
LM4.
: 0, 0, 48
TM4.
: 26, 26, 74
LDSF4.
: 100, 100, 70
DEFBIN4.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER4. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 5
PREMUL5. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL5.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR5.
: NO
MPL5.
: 66, ENA
MPP5.
: 132, ENA
LPI5.
: 6 (3, 4, 6, 8)
CPI5.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI5.
AUTORI5.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
: YES
307
308
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
LM5.
: 0, 0, 48
TM5.
: 26, 26, 74
LDSF5.
: 100, 100, 70
DEFBIN5.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER5. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 6
PREMUL6. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL6.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR6.
: NO
MPL6.
: 66, ENA
MPP6.
: 132, ENA
LPI6.
: 6 (3, 4, 6, 8)
CPI6.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI6.
AUTORI6.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
: YES
LM6.
: 0, 0, 48
TM6.
: 26, 26, 74
LDSF6.
: 100, 100, 70
DEFBIN6.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER6. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 7
PREMUL7. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL7.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
AXIS 5570e/AXIS 5670e User’s Manual
PASSTHR7.
: NO
MPL7.
: 66, ENA
MPP7.
: 132, ENA
LPI7.
: 6 (3, 4, 6, 8)
CPI7.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI7.
Section 23: The Parameter List
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI7.
: YES
LM7.
: 0, 0, 48
TM7.
: 26, 26, 74
LDSF7.
: 100, 100, 70
DEFBIN7.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER7. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 8
PREMUL8. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL8.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR8.
: NO
MPL8.
: 66, ENA
MPP8.
: 132, ENA
LPI8.
: 6 (3, 4, 6, 8)
CPI8.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI8.
AUTORI8.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
: YES
LM8.
: 0, 0, 48
TM8.
: 26, 26, 74
LDSF8.
: 100, 100, 70
DEFBIN8.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER8. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
309
310
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
--- IBM SCS PAGE FORMAT
PCORI.
: NO
DWSISO.
: NO
BIN1.
: COR, LETTER, 0, 0
BIN2.
: COR, LETTER, 0, 0
BIN3.
: COR, LETTER, 0, 0
BIN4.
: COR, LETTER, 0, 0
BIN5.
: COR, LETTER, 0, 0
BIN6.
: COR, LETTER, 0, 0
MANUAL.
: COR, LETTER, 0, 0
ENVELOPE.
: COR, LETTER, 0, 0
CONTINUOUS. : COR, LETTER, 0, 0
SIMBF.
: YES
--- IBM SCS CPI MAPPING
FGID_CPI5. : 244, 11
FGID_CPI10. : 11, 204
FGID_CPI12. : 86, 230
FGID_CPI15. : 230, 281
FGID_CPI17. : 252, 281
FGID_CPI8COR. : 86
FGID_CPI20COR. : 281
FGID_CPI25COR. : 289
FGID_CPI27COR. : 290
PROPOCOR.
TYPOCOR.
: 230
: 230
--- IBM SCS JOB CONTROL
REINIT.
: YES
SUPFFBLANK. : NO
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
--- IBM 3270 OPTIONS
CASE.
: DUAL (DUAL, MONO)
BASCOL.
: BLACK, ENA
XSTRN.
:0
AUTNL.
:1
ADDNL.
:1
FFWPB.
:0
FFEOPB.
:1
NULSUP.
:0
FFCPOS.
:0
AFEOPB.
:0
--- IBM SCS EXTENDED EMULATION
XEMUL.
: YES
WARN.
: NO
SSUBST.
: YES
SBTS.
:
TLIS.
: 025 03C
TTRS.
: 03E 025
FLIS.
: 025 02F
EECS.
COBXEM.
CCLIS.
: 025 041 058 049 053
: SETALL (OFF, SETESC, SETALL)
: 025 050
--- UDS
-------
--- BAR
NUMBER TYPE WIDTH HEIGHT TEXT-MODE CHECK-MODE
-------------------------------------------------------------
311
312
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
--- SSTR
--------
--- MSTR
--------
--- IBM PRINTER DRIVER
PRDRIVERBASE. : PCL5 (GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
SOJS.
: 1B 45 1B 26 6C 30 4C
EOJS.
: 1B 45
BACKSPS.
: 08
CRS.
: 0D
LFS.
: 0A
NLS.
: 0D 0A
FFS.
: 0C
SOS.
:
SIS.
BLKS.
:
:
GRNS.
:
BLUS.
:
REDS.
:
MAGS.
:
CYNS.
YELS.
:
:
BIN1S.
: 1B 26 6C 31 48
BIN2S.
: 1B 26 6C 34 48
BIN3S.
: 1B 26 6C 35 48
BIN4S.
: 1B 26 6C 32 30 48
BIN5S.
: 1B 26 6C 32 31 48
BIN6S.
: 1B 26 6C 32 32 48
MANUALS.
: 1B 26 6C 32 48
ENVELOPES. : 1B 26 6C 36 48
CONTINUOUSS. : 1B 26 6C 31 48
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
CSIZS.
:
LAC.
: HP_PCL (DISABLE, HP_PCL, EPSON_LQ)
GRD.
: HP_PCL (DISABLE, HP_PCL, EPSON_LQ)
JOGS.
: 1B 26 6C 31 54
SSUS.
:
SBSET.
: PC850 (ECMA94, LATIN9, PC437, PC850, PC852, PC857, PC858, PC874, PC891,
PC903, PC904, PC942, ROMAN8, USASCII, USER)
--- FONT
FGID CSSF SBSET SPACING PITCH HEIGHT STYLE STROKE TYPEFACE STRING
---------------------------------------------------------------------------------FONT.
: 3,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 5,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 11, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 12, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 13, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 18, 98, DEFAULT,FIXED, 100, 0,
ITALIC,MEDIUM,4099,
FONT.
: 19, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4200,
FONT.
: 20, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 30, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 38, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,BOLD, 4102,
FONT.
: 39, 98, DEFAULT,FIXED, 135, 0,
UPRIGHT,BOLD, 4102,
FONT.
: 40, 98, DEFAULT,FIXED, 135, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 41, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 42, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 43, 98, DEFAULT,FIXED, 100, 0,
ITALIC,MEDIUM,4099,
FONT.
: 46, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 60, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 66, 98, DEFAULT,FIXED, 150, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 68, 98, DEFAULT,FIXED, 150, 0,
ITALIC,MEDIUM,4102,
FONT.
: 69, 98, DEFAULT,FIXED, 150, 0,
UPRIGHT,BOLD, 4102,
FONT.
: 70, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 71, 98, DEFAULT,FIXED, 120, 0,
ITALIC,MEDIUM,4099,
FONT.
: 72, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 80, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,MEDIUM,4099,
1B 28 31 4F
1B 28 30 4F
313
314
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
FONT.
: 84, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 85, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 86, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 87, 98, DEFAULT,FIXED, 130, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 91, 98, DEFAULT,FIXED, 120, 0,
ITALIC,MEDIUM,4099,
FONT.
: 108, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 110, 98, DEFAULT,FIXED, 130, 0,
UPRIGHT,BOLD, 4102,
FONT.
: 111, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 112, 98, DEFAULT,FIXED, 120, 0,
ITALIC,MEDIUM,4099,
FONT.
: 155, 100, DEFAULT,PROP, 0,
110, ITALIC,BOLD, 4101,
FONT.
: 158, 100, DEFAULT,PROP, 0,
110, UPRIGHT,MEDIUM,4101,
FONT.
: 159, 100, DEFAULT,PROP, 0,
110, UPRIGHT,BOLD, 4101,
FONT.
: 160, 100, DEFAULT,PROP, 0,
110, UPRIGHT,MEDIUM,4148,
FONT.
: 162, 100, DEFAULT,PROP, 0,
110, ITALIC,MEDIUM,4148,
FONT.
: 163, 100, DEFAULT,PROP, 0,
110, UPRIGHT,BOLD, 4148,
FONT.
: 173, 100, DEFAULT,PROP, 0,
110, UPRIGHT,LIGHT, 4148,
FONT.
: 175, 100, DEFAULT,PROP, 0,
110, UPRIGHT,MEDIUM,4101,
FONT.
: 204, 98, DEFAULT,FIXED, 167, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 221, 98, DEFAULT,FIXED, 150, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 223, 98, DEFAULT,FIXED, 150, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 225, 98, DEFAULT,FIXED, 150, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 229, 98, DEFAULT,FIXED, 150, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 230, 98, DEFAULT,FIXED, 180, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 244, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 245, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 252, 98, DEFAULT,FIXED, 171, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 253, 98, DEFAULT,FIXED, 171, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 254, 98, DEFAULT,FIXED, 220, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 258, 98, DEFAULT,FIXED, 180, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 266, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 281, 98, DEFAULT,FIXED, 233, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 289, 98, DEFAULT,FIXED, 267, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 290, 98, DEFAULT,FIXED, 300, 0,
UPRIGHT,MEDIUM,4102,
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
FONT.
: 751, 100, DEFAULT,PROP, 0,
80,
FONT.
: 1051, 100, DEFAULT,PROP, 0,
100, UPRIGHT,MEDIUM,4101,
FONT.
: 1053, 100, DEFAULT,PROP, 0,
100, UPRIGHT,BOLD, 4101,
FONT.
: 1056, 100, DEFAULT,PROP, 0,
100, ITALIC,MEDIUM,4101,
FONT.
: 1351, 100, DEFAULT,PROP, 0,
120, UPRIGHT,MEDIUM,4101,
FONT.
: 1653, 100, DEFAULT,PROP, 0,
160, UPRIGHT,BOLD, 4101,
FONT.
: 2103, 100, DEFAULT,PROP, 0,
240, UPRIGHT,BOLD, 4101,
FONT.
: 3840, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4101,
FONT.
: 3841, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4101,
FONT.
: 3842, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4101,
FONT.
: 3843, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4101,
FONT.
: 3844, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4113,
FONT.
: 3845, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4113,
FONT.
: 3846, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4113,
FONT.
: 3847, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4113,
FONT.
: 3848, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4116,
: 3849, 100, DEFAULT,PROP, 0,
0,
NONE, MEDIUM,4140,
FONT.
UPRIGHT,MEDIUM,4101,
1B
28 73 34 53
FONT.
: 3850, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4148,
FONT.
: 3851, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4148,
FONT.
: 3852, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4148,
FONT.
: 3853, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4148,
FONT.
: 3854, 100, DEFAULT,PROP, 0,
0,
NONE, MEDIUM,4148,
0,
NONE, BOLD, 4148,
0,
NONE, MEDIUM,4148,
0,
NONE, BOLD, 4148,
1B
28 73 34 53
FONT.
: 3855, 100, DEFAULT,PROP, 0,
1B
28 73 34 53
FONT.
: 3856, 100, DEFAULT,PROP, 0,
1B
28 73 35 53
FONT.
: 3857, 100, DEFAULT,PROP, 0,
1B
28 73 35 53
FONT.
: 3858, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4168,
FONT.
: 3859, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4168,
FONT.
: 3860, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4168,
315
316
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
FONT.
: 3861, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4197,
FONT.
: 3862, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4197,
FONT.
: 3863, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4197,
FONT.
: 3864, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4197,
FONT.
: 3865, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4297,
FONT.
: 3866, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,NONE, 4362,
1B 28 73 31 42
FONT.
: 3867, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,NONE, 4362,
1B 28 73 34 42
FONT.
: 3868, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,16602,
FONT.
: 3869, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 16602,
FONT.
: 3870, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,16602,
FONT.
: 3871, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 16602,
FONT.
: 3872, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,16901,
FONT.
: 3873, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 16901,
FONT.
: 3874, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,16901,
FONT.
: 3875, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 16901,
FONT.
: 3876, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,16686, 1B 28 31 39 4D
FONT.
: 3877, 100, DEFAULT,PROP, 0, 0,
FONT.
: 5687, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,16901,
FONT.
: 5707, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 16901,
FONT.
: 5815, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,16901,
UPRIGHT,MEDIUM,31402, 1B 28 35 37 39 4C
FONT.
: 5835, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 16901,
FONT.
: 6199, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4197,
FONT.
: 6219, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4197,
FONT.
: 6327, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4197,
FONT.
: 6347, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4197,
FONT.
: 16951,100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4101,
FONT.
: 16971,100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4101,
FONT.
: 17079,100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4101,
FONT.
: 17099,100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4101,
FONT.
: 33335,100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4113,
FONT.
: 33355,100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4113,
FONT.
: 33463,100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4113,
FONT.
: 33483,100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4113,
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
FONT.
: 33591,100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,16602,
FONT.
: 33601,100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 16602,
FONT.
: 33719,100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,16602,
FONT.
: 33729,100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 16602,
FONT.
: 34103,100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4148,
FONT.
: 34123,100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4148,
FONT.
: 34231,100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4148,
FONT.
: 34251,100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4148,
FONT.
: 41783,100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4116,
FONT.
: 41803,100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4116,
FONT.
: 41911,100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4116,
FONT.
: 41931,100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4116,
FONT.
: 50000,100, PC942,PROP, 0,
144, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50001,100, PC942,PROP, 0,
144, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50002,100, PC942,PROP, 0,
120, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50003,100, PC942,PROP, 0,
108, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50004,100, PC942,PROP, 0,
96,
UPRIGHT,MEDIUM,28752, 1B
96,
UPRIGHT,MEDIUM,28752, 1B
80,
UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50005,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50006,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50007,100, PC942,PROP, 0,
101, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50008,100, PC942,PROP, 0,
101, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50009,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
84,
UPRIGHT,MEDIUM,28752, 1B
317
318
Section 23: The Parameter List
FONT.
AXIS 5570e/AXIS 5670e User’s Manual
: 50010,100, PC942,PROP, 0,
76,
UPRIGHT,MEDIUM,28752, 1B
67,
UPRIGHT,MEDIUM,28752, 1B
67,
UPRIGHT,MEDIUM,28752, 1B
56,
UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50011,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50012,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50013,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50014,100, PC942,PROP, 0,
144, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50015,100, PC942,PROP, 0,
120, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50016,100, PC942,PROP, 0,
108, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50017,100, PC942,PROP, 0,
96,
UPRIGHT,MEDIUM,28752, 1B
80,
UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50018,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50019,100, PC942,PROP, 0,
101, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50020,100, PC942,PROP, 0,
84,
UPRIGHT,MEDIUM,28752, 1B
76,
UPRIGHT,MEDIUM,28752, 1B
67,
UPRIGHT,MEDIUM,28752, 1B
56,
UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50021,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50022,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50023,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50030,100, PC891,PROP, 0,
144, UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50031,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
144, UPRIGHT,MEDIUM,43088, 1B
AXIS 5570e/AXIS 5670e User’s Manual
FONT.
: 50032,100, PC891,PROP, 0,
Section 23: The Parameter List
120, UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50033,100, PC891,PROP, 0,
108, UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50034,100, PC891,PROP, 0,
96,
UPRIGHT,MEDIUM,43088, 1B
96,
UPRIGHT,MEDIUM,43088, 1B
80,
UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50035,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50036,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50037,100, PC891,PROP, 0,
101, UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50038,100, PC891,PROP, 0,
101, UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50039,100, PC891,PROP, 0,
84,
UPRIGHT,MEDIUM,43088, 1B
76,
UPRIGHT,MEDIUM,43088, 1B
67,
UPRIGHT,MEDIUM,43088, 1B
67,
UPRIGHT,MEDIUM,43088, 1B
56,
UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50040,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50041,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50042,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50043,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50044,100, PC891,PROP, 0,
144, UPRIGHT,MEDIUM,41040, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50045,100, PC891,PROP, 0,
120, UPRIGHT,MEDIUM,41040, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50046,100, PC891,PROP, 0,
108, UPRIGHT,MEDIUM,41040, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50047,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
96,
UPRIGHT,MEDIUM,41040, 1B
319
320
Section 23: The Parameter List
FONT.
AXIS 5570e/AXIS 5670e User’s Manual
: 50048,100, PC891,PROP, 0,
80,
UPRIGHT,MEDIUM,41040, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50049,100, PC891,PROP, 0,
101, UPRIGHT,MEDIUM,41040, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50050,100, PC891,PROP, 0,
84,
UPRIGHT,MEDIUM,41040, 1B
76,
UPRIGHT,MEDIUM,41040, 1B
67,
UPRIGHT,MEDIUM,41040, 1B
56,
UPRIGHT,MEDIUM,41040, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50051,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50052,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50053,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50060,100, PC904,PROP, 0,
144, UPRIGHT,MEDIUM,0,
FONT.
: 50061,100, PC904,PROP, 0,
144, UPRIGHT,MEDIUM,0,
FONT.
: 50062,100, PC904,PROP, 0,
120, UPRIGHT,MEDIUM,0,
FONT.
: 50063,100, PC904,PROP, 0,
108, UPRIGHT,MEDIUM,0,
FONT.
: 50064,100, PC904,PROP, 0,
96,
UPRIGHT,MEDIUM,0,
FONT.
: 50065,100, PC904,PROP, 0,
96,
UPRIGHT,MEDIUM,0,
FONT.
: 50066,100, PC904,PROP, 0,
80,
UPRIGHT,MEDIUM,0,
FONT.
: 50067,100, PC904,PROP, 0,
101, UPRIGHT,MEDIUM,0,
FONT.
: 50068,100, PC904,PROP, 0,
101, UPRIGHT,MEDIUM,0,
FONT.
: 50069,100, PC904,PROP, 0,
84,
UPRIGHT,MEDIUM,0,
FONT.
: 50070,100, PC904,PROP, 0,
76,
UPRIGHT,MEDIUM,0,
FONT.
: 50071,100, PC904,PROP, 0,
67,
UPRIGHT,MEDIUM,0,
FONT.
: 50072,100, PC904,PROP, 0,
67,
UPRIGHT,MEDIUM,0,
FONT.
: 50073,100, PC904,PROP, 0,
56,
UPRIGHT,MEDIUM,0,
FONT.
: 50074,100, PC904,PROP, 0,
144, UPRIGHT,MEDIUM,0,
FONT.
: 50075,100, PC904,PROP, 0,
120, UPRIGHT,MEDIUM,0,
FONT.
: 50076,100, PC904,PROP, 0,
108, UPRIGHT,MEDIUM,0,
FONT.
: 50077,100, PC904,PROP, 0,
96,
UPRIGHT,MEDIUM,0,
FONT.
: 50078,100, PC904,PROP, 0,
80,
UPRIGHT,MEDIUM,0,
FONT.
: 50079,100, PC904,PROP, 0,
101, UPRIGHT,MEDIUM,0,
FONT.
: 50080,100, PC904,PROP, 0,
84,
UPRIGHT,MEDIUM,0,
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
FONT.
: 50081,100, PC904,PROP, 0,
76,
UPRIGHT,MEDIUM,0,
FONT.
: 50082,100, PC904,PROP, 0,
67,
UPRIGHT,MEDIUM,0,
FONT.
: 50083,100, PC904,PROP, 0,
56,
UPRIGHT,MEDIUM,0,
FONT.
: 50100,100, PC903,PROP, 0,
144, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50101,100, PC903,PROP, 0,
144, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50102,100, PC903,PROP, 0,
120, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50103,100, PC903,PROP, 0,
108, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50104,100, PC903,PROP, 0,
96,
UPRIGHT,MEDIUM,37058, 1B
96,
UPRIGHT,MEDIUM,37058, 1B
80,
UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50105,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50106,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50107,100, PC903,PROP, 0,
101, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50108,100, PC903,PROP, 0,
101, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50109,100, PC903,PROP, 0,
84,
UPRIGHT,MEDIUM,37058, 1B
76,
UPRIGHT,MEDIUM,37058, 1B
67,
UPRIGHT,MEDIUM,37058, 1B
67,
UPRIGHT,MEDIUM,37058, 1B
56,
UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50110,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50111,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50112,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50113,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50114,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
144, UPRIGHT,MEDIUM,37058, 1B
321
322
Section 23: The Parameter List
FONT.
AXIS 5570e/AXIS 5670e User’s Manual
: 50115,100, PC903,PROP, 0,
120, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50116,100, PC903,PROP, 0,
108, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50117,100, PC903,PROP, 0,
96,
UPRIGHT,MEDIUM,37058, 1B
80,
UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50118,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50119,100, PC903,PROP, 0,
101, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50120,100, PC903,PROP, 0,
84,
UPRIGHT,MEDIUM,37058, 1B
76,
UPRIGHT,MEDIUM,37058, 1B
67,
UPRIGHT,MEDIUM,37058, 1B
56,
UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50121,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50122,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50123,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50130,100, PC891,PROP, 0,
144, UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50131,100, PC891,PROP, 0,
144, UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50132,100, PC891,PROP, 0,
120, UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50133,100, PC891,PROP, 0,
108, UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50134,100, PC891,PROP, 0,
96,
UPRIGHT,MEDIUM,43088, 1B
96,
UPRIGHT,MEDIUM,43088, 1B
80,
UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50135,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50136,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
AXIS 5570e/AXIS 5670e User’s Manual
FONT.
: 50137,100, PC891,PROP, 0,
Section 23: The Parameter List
101, UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50138,100, PC891,PROP, 0,
101, UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50139,100, PC891,PROP, 0,
84,
UPRIGHT,MEDIUM,43088, 1B
76,
UPRIGHT,MEDIUM,43088, 1B
67,
UPRIGHT,MEDIUM,43088, 1B
67,
UPRIGHT,MEDIUM,43088, 1B
56,
UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50140,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50141,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50142,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50143,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50144,100, PC891,PROP, 0,
144, UPRIGHT,MEDIUM,41040, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50145,100, PC891,PROP, 0,
120, UPRIGHT,MEDIUM,41040, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50146,100, PC891,PROP, 0,
108, UPRIGHT,MEDIUM,41040, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50147,100, PC891,PROP, 0,
96,
UPRIGHT,MEDIUM,41040, 1B
80,
UPRIGHT,MEDIUM,41040, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50148,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50149,100, PC891,PROP, 0,
101, UPRIGHT,MEDIUM,41040, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50150,100, PC891,PROP, 0,
84,
UPRIGHT,MEDIUM,41040, 1B
76,
UPRIGHT,MEDIUM,41040, 1B
67,
UPRIGHT,MEDIUM,41040, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50151,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50152,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
323
324
Section 23: The Parameter List
FONT.
AXIS 5570e/AXIS 5670e User’s Manual
: 50153,100, PC891,PROP, 0,
56,
UPRIGHT,MEDIUM,41040, 1B
28 31 38 48 1B 26 74 33 38 50
--- Email Menu
EMAIL_NOTIFICATION. : YES
REPLY_ADDRESS. :
PAPER_JAM_ADDRESS. :
OUT_OF_PAPER_ADDRESS. :
TONER_LOW_ADDRESS. :
NO_TONER_ADDRESS. :
PRINTER_OFFLINE_ADDRESS. :
AXIS 5670e:
--- General Menu
NODE_ADDR. : 00 40 8C XX XX XX
NETWORK_SPEED. : AUTO_SENSE (AUTO_SENSE, 10_HALF_DX, 10_FULL_DX, 100_HALF_DX,
100_FULL_DX)
PS_NAME.
: AXISXXXXXX
ROOT_PWD.
: pass
SWUP_KEY.
:
USERS.
:
BASE_URL.
: www.axis.com
CHARSET.
: ISO-8859-1 (ISO-8859-1, UTF-8)
AXIS_PRINT_SYSTEM. : YES
RCONFIG_ENB. : YES
DEF_OUT.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2)
SYS_LOC.
:
SYS_CONT.
:
--- SNA Menu
SNA_ENB.
: YES
DEVICE_EMUL. : 3174 (3174, 5494)
SNA_FR_TYPE. : FR_802_2 (FR_AUTO, FR_802_2, FR_DIX)
AXIS 5570e/AXIS 5670e User’s Manual
NODE_ID.
Section 23: The Parameter List
: E0 78 1E 58
NODE_SAP.
: $4
NWORK_NAME. : APPN
LU_NAME.
H1_SAP.
: A85E181C
: $4
H1_ADDR.
: FF FF FF FF FF FF
H1_NW_NAME. : APPN
H1_MOD_NAME. : QRMTWSC
H1_LU_NAME. : DEFAULT
SNA_LU1.
: NONE, 1
SNA_LU2.
: NONE, 2
SNA_LU3.
: NONE, 3
SNA_LU4.
: NONE, 4
SNA_LU5.
: NONE, 5
SNA_LU6.
: NONE, 6
SNA_LU7.
: NONE, 7
SNA_LU8.
: NONE, 8
AUTODIAL.
: NO
DIALTIME.
: 20
JOB_TIME.
: 10
IR_TIME.
:0
SNA_HEXDUMP. : NONE (NONE, PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
--- TN3270E
TN3270E_IR. : 0
TN3270E_COMP. : NO
TN3270E_1. : OFF, 0 0 0 0, 23, PR1, 1, AXPR1
TN3270E_2. : OFF, 0 0 0 0, 23, PR2, 2, AXPR2
TN3270E_3. : OFF, 0 0 0 0, 23, PR3, 3, AXPR3
TN3270E_4. : OFF, 0 0 0 0, 23, PR4, 4, AXPR4
TN3270E_5. : OFF, 0 0 0 0, 23, PR5, 5, AXPR5
TN3270E_6. : OFF, 0 0 0 0, 23, PR6, 6, AXPR6
TN3270E_7. : OFF, 0 0 0 0, 23, PR7, 7, AXPR7
325
326
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
TN3270E_8. : OFF, 0 0 0 0, 23, PR8, 8, AXPR8
--- TN5250E
TN5250E_KA. : YES
TN5250E_1. : OFF, 0 0 0 0, 23, PR1, 1, AXPR1, QSYSOPR, QSYS
TN5250E_2. : OFF, 0 0 0 0, 23, PR2, 2, AXPR2, QSYSOPR, QSYS
TN5250E_3. : OFF, 0 0 0 0, 23, PR3, 3, AXPR3, QSYSOPR, QSYS
TN5250E_4. : OFF, 0 0 0 0, 23, PR4, 4, AXPR4, QSYSOPR, QSYS
TN5250E_5. : OFF, 0 0 0 0, 23, PR5, 5, AXPR5, QSYSOPR, QSYS
TN5250E_6. : OFF, 0 0 0 0, 23, PR6, 6, AXPR6, QSYSOPR, QSYS
TN5250E_7. : OFF, 0 0 0 0, 23, PR7, 7, AXPR7, QSYSOPR, QSYS
TN5250E_8. : OFF, 0 0 0 0, 23, PR8, 8, AXPR8, QSYSOPR, QSYS
--- TCP/IP Menu
TCP_ENB.
: YES
INT_ADDR.
:0000
DEF_ROUT.
:0000
NET_MASK.
:0000
HTTPS_ENB. : NO
PROS_PWD.
: netprinter
PROS_PRT.
: 35
LPD_BANN.
: OFF (OFF, AUTO, LAST)
DHCP_ENB.
: NO
AUTOIP_ENB. : NO
BOOTP_ENB. : YES
RARP_ENB.
: YES
WINS_ENB.
: YES
WINS_ADDR1. : 0 0 0 0
WINS_ADDR2. : 0 0 0 0
NBT_SCOPE_ID. :
DNS_ENB.
: YES
DNS_ADDR1. : 0 0 0 0
DNS_ADDR2. : 0 0 0 0
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
DOMAIN_NAME. :
SLP_ENB.
: YES
SLP_SCOPE_LIST. : DEFAULT
SMTP_SERVER. :
FTP_ENB.
: YES
TELNET_ENB. : YES
DEFAULT_RAW_TCP. : 9100-9102 (9100-9102, CLOSED)
RTN_OPT.
: NO
PPR_PRSTAT. : NO
RTN_PR1.
: 5001, IPDS, 1
RTN_PR2.
: 0, ASCII, 2
RTN_PR3.
: 0, ASCII, 3
RTN_PR4.
: 5011, SCS, 4
RTN_PR5.
: 5012, SCS, 5
RTN_PR6.
: 5013, SCS, 6
RTN_PR7.
: 0, ASCII, 7
RTN_PR8.
: 0, ASCII, 8
DEF_IP_FRAME_TYPE. : EthernetII (EthernetII, SNAP)
--- SNMP Menu
SNMP_ENB.
: YES
SNMP_V1_CONFIG. : YES
READ_COM.
: public
WRT_COM.
: pass
TRAPADDR.
:0000
TRAP_COM.
: public
SYS_NAME.
:
SNMP_AUT.
: DISABLE (DISABLE, ENABLE)
TRAP_PRT.
: DISABLE (DISABLE, ENABLE)
--- NetWare Menu
NETW_ENB.
: YES
NETW_TRANSPORT_PROTOCOL. : DUAL_STACK (IPX_ONLY, IP_ONLY, DUAL_STACK)
327
328
Section 23: The Parameter List
NDPS.
AXIS 5570e/AXIS 5670e User’s Manual
: TCP_AND_SPX (TCP_AND_SPX, TCP_ONLY, SPX_ONLY, DISABLED)
JOB_CHECK_DELAY. : 5
CONF_CHECK_DELAY. : 300
FR_802_3.
: YES
FR_ETH_2.
: YES
FR_802_2.
: YES
FR_SNAP.
: YES
NCP_BURST_MODE. : YES
PSERVER_NDS_TREE. :
PSERVER_NDS_FILESERVER. :
PSERVER_NDS_DISTINGUISHED_NAME. :
PSERVER_BINDERY1. :
PSERVER_BINDERY2. :
PSERVER_BINDERY3. :
PSERVER_BINDERY4. :
PSERVER_BINDERY5. :
PSERVER_BINDERY6. :
PSERVER_BINDERY7. :
PSERVER_BINDERY8. :
PSERVER_BINDERY9. :
PSERVER_BINDERY10. :
PSERVER_BINDERY11. :
PSERVER_BINDERY12. :
PSERVER_BINDERY13. :
PSERVER_BINDERY14. :
PSERVER_BINDERY15. :
PSERVER_BINDERY16. :
NPRINTER1. :
NPRINTER2. :
NPRINTER3. :
NPRINTER4. :
NPRINTER5. :
NPRINTER6. :
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
NPRINTER7. :
NPRINTER8. :
--- NetBIOS/NetBEUI Menu
LSLM_ENB.
: YES
NB_FR_TYPE. : FR_802_2 (FR_AUTO, FR_802_2, FR_DIX)
LPRINT_1.
: AX181E58.LP1
LLOGIC_1.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2)
LPRINT_2.
: AX181E58.LP2
LLOGIC_2.
: PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2)
LPRINT_3.
: AX181E58.CM1
LLOGIC_3.
: PR3 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2)
LPRINT_4.
:
LLOGIC_4.
: PR4 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2)
LPRINT_5.
:
LLOGIC_5.
: PR5 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2)
LPRINT_6.
:
LLOGIC_6.
: PR6 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2)
LPRINT_7.
:
LLOGIC_7.
: PR7 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2)
LPRINT_8.
:
LLOGIC_8.
: PR8 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2)
--- AppleTalk Menu
ATLK_ENB.
: YES
ATK_ZONE.
:
ZONER_EN.
: YES
ATK_FONT.
: DEFAULT (DEFAULT, 35N, ALL)
AUTO_DT_PRIN. : NO
APRINT_1.
: AXIS181E58_LPT1
ATYPE_1.
: LaserWriter
ALOGIC_1.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2)
BINARY_TYPE_1. : TBCP (TBCP, BCP, NONE)
329
330
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
APRINT_2.
: AXIS181E58_LPT2
ATYPE_2.
: LaserWriter
ALOGIC_2.
: PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2)
BINARY_TYPE_2. : TBCP (TBCP, BCP, NONE)
APRINT_3.
: AXIS181E58_COM1
ATYPE_3.
: LaserWriter
ALOGIC_3.
: PR3 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2)
BINARY_TYPE_3. : TBCP (TBCP, BCP, NONE)
--- Printer1 Menu
PR1_OUT.
: LPT1 (NONE, LPT1, COM1, LPT2)
PR1_NAME.
:
PR1_SCND.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR1_WAIT.
: YES
PR1_IN.
: AUTO (AUTO, NONE, COM1)
PR1_BEF.
:
PR1_STR.
:
PR1_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR1_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR1_AFT.
:
PR1_DUMP.
PR1_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR1_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR1_FORM.
: 66 0 100 60 30 50
PR1_FONT.
:
PR1_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605, Canon_IR3300,
Gestetner_3235, Gestetner_3245, Gestetner_3255, Gestetner_3265, Gestetner_P7032,
HP_LaserJet_5Si, Minolta_Di250, Minolta_Di350, Minolta_Di520, Minolta_Di620,
Minolta_PI_5500, Ricoh_Aficio_220, Ricoh_Aficio_270, Ricoh_Aficio_350, Ricoh_Aficio_450,
Ricoh_Aficio_550, Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP, Sharp_AR286_FN1,
Sharp_AR336_FN1, Sharp_AR405_FN1, Sharp_AR505_FN1, Sharp_AR286_FN2,
Sharp_AR336_FN2, Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070, Toshiba_eSTUDIO35,
Toshiba_eSTUDIO45, Toshiba_eSTUDIO55, Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR1_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING, SHORT_EDGE_BINDING)
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
PR1_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL, TOP_LEFT_VERTICAL,
TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT, TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR1_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR1_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR1_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR1_DC_COP. : 1
--- Printer2 Menu
PR2_OUT.
: LPT2 (NONE, LPT1, COM1, LPT2)
PR2_NAME.
:
PR2_SCND.
: PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR2_WAIT.
: YES
PR2_IN.
: AUTO (AUTO, NONE, COM1)
PR2_BEF.
:
PR2_STR.
:
PR2_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR2_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR2_AFT.
:
PR2_DUMP.
PR2_SIZE.
PR2_ORNT.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR2_FORM.
PR2_FONT.
: 66 0 100 60 30 50
:
PR2_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605, Canon_IR3300,
Gestetner_3235, Gestetner_3245, Gestetner_3255, Gestetner_3265, Gestetner_P7032,
HP_LaserJet_5Si, Minolta_Di250, Minolta_Di350, Minolta_Di520, Minolta_Di620,
Minolta_PI_5500, Ricoh_Aficio_220, Ricoh_Aficio_270, Ricoh_Aficio_350, Ricoh_Aficio_450,
Ricoh_Aficio_550, Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP, Sharp_AR286_FN1,
Sharp_AR336_FN1, Sharp_AR405_FN1, Sharp_AR505_FN1, Sharp_AR286_FN2,
Sharp_AR336_FN2, Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070, Toshiba_eSTUDIO35,
Toshiba_eSTUDIO45, Toshiba_eSTUDIO55, Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR2_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING, SHORT_EDGE_BINDING)
PR2_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL, TOP_LEFT_VERTICAL,
TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT, TOP_DOUBLE, LEFT_DOUBLE, CENTER)
331
332
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
PR2_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR2_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR2_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR2_DC_COP. : 1
--- Printer3 Menu
PR3_OUT.
: COM1 (NONE, LPT1, COM1, LPT2)
PR3_NAME.
:
PR3_SCND.
: PR3 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR3_WAIT.
: YES
PR3_IN.
: AUTO (AUTO, NONE, COM1)
PR3_BEF.
:
PR3_STR.
:
PR3_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR3_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR3_AFT.
:
PR3_DUMP.
PR3_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR3_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR3_FORM.
: 66 0 100 60 30 50
PR3_FONT.
:
PR3_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605, Canon_IR3300,
Gestetner_3235, Gestetner_3245, Gestetner_3255, Gestetner_3265, Gestetner_P7032,
HP_LaserJet_5Si, Minolta_Di250, Minolta_Di350, Minolta_Di520, Minolta_Di620,
Minolta_PI_5500, Ricoh_Aficio_220, Ricoh_Aficio_270, Ricoh_Aficio_350, Ricoh_Aficio_450,
Ricoh_Aficio_550, Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP, Sharp_AR286_FN1,
Sharp_AR336_FN1, Sharp_AR405_FN1, Sharp_AR505_FN1, Sharp_AR286_FN2,
Sharp_AR336_FN2, Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070, Toshiba_eSTUDIO35,
Toshiba_eSTUDIO45, Toshiba_eSTUDIO55, Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR3_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING, SHORT_EDGE_BINDING)
PR3_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL, TOP_LEFT_VERTICAL,
TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT, TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR3_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR3_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
PR3_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR3_DC_COP. : 1
--- Printer4 Menu
PR4_OUT.
: COM1 (NONE, LPT1, COM1, LPT2)
PR4_NAME.
:
PR4_SCND.
: PR4 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR4_WAIT.
: YES
PR4_IN.
: AUTO (AUTO, NONE, COM1)
PR4_BEF.
:
PR4_STR.
:
PR4_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR4_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR4_AFT.
:
PR4_DUMP.
PR4_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR4_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR4_FORM.
: 66 0 100 60 30 50
PR4_FONT.
:
PR4_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605, Canon_IR3300,
Gestetner_3235, Gestetner_3245, Gestetner_3255, Gestetner_3265, Gestetner_P7032,
HP_LaserJet_5Si, Minolta_Di250, Minolta_Di350, Minolta_Di520, Minolta_Di620,
Minolta_PI_5500, Ricoh_Aficio_220, Ricoh_Aficio_270, Ricoh_Aficio_350, Ricoh_Aficio_450,
Ricoh_Aficio_550, Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP, Sharp_AR286_FN1,
Sharp_AR336_FN1, Sharp_AR405_FN1, Sharp_AR505_FN1, Sharp_AR286_FN2,
Sharp_AR336_FN2, Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070, Toshiba_eSTUDIO35,
Toshiba_eSTUDIO45, Toshiba_eSTUDIO55, Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR4_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING, SHORT_EDGE_BINDING)
PR4_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL, TOP_LEFT_VERTICAL,
TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT, TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR4_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR4_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR4_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR4_DC_COP. : 1
333
334
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
--- Printer5 Menu
PR5_OUT.
: LPT1 (NONE, LPT1, COM1, LPT2)
PR5_NAME.
:
PR5_SCND.
: PR5 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR5_WAIT.
: YES
PR5_IN.
: AUTO (AUTO, NONE, COM1)
PR5_BEF.
:
PR5_STR.
:
PR5_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR5_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR5_AFT.
:
PR5_DUMP.
PR5_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR5_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR5_FORM.
: 66 0 100 60 30 50
PR5_FONT.
:
PR5_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605, Canon_IR3300,
Gestetner_3235, Gestetner_3245, Gestetner_3255, Gestetner_3265, Gestetner_P7032,
HP_LaserJet_5Si, Minolta_Di250, Minolta_Di350, Minolta_Di520, Minolta_Di620,
Minolta_PI_5500, Ricoh_Aficio_220, Ricoh_Aficio_270, Ricoh_Aficio_350, Ricoh_Aficio_450,
Ricoh_Aficio_550, Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP, Sharp_AR286_FN1,
Sharp_AR336_FN1, Sharp_AR405_FN1, Sharp_AR505_FN1, Sharp_AR286_FN2,
Sharp_AR336_FN2, Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070, Toshiba_eSTUDIO35,
Toshiba_eSTUDIO45, Toshiba_eSTUDIO55, Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR5_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING, SHORT_EDGE_BINDING)
PR5_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL, TOP_LEFT_VERTICAL,
TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT, TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR5_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR5_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR5_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR5_DC_COP. : 1
--- Printer6 Menu
AXIS 5570e/AXIS 5670e User’s Manual
PR6_OUT.
Section 23: The Parameter List
: LPT2 (NONE, LPT1, COM1, LPT2)
PR6_NAME.
:
PR6_SCND.
: PR6 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR6_WAIT.
: YES
PR6_IN.
: AUTO (AUTO, NONE, COM1)
PR6_BEF.
:
PR6_STR.
:
PR6_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR6_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR6_AFT.
:
PR6_DUMP.
PR6_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR6_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR6_FORM.
: 66 0 100 60 30 50
PR6_FONT.
:
PR6_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605, Canon_IR3300,
Gestetner_3235, Gestetner_3245, Gestetner_3255, Gestetner_3265, Gestetner_P7032,
HP_LaserJet_5Si, Minolta_Di250, Minolta_Di350, Minolta_Di520, Minolta_Di620,
Minolta_PI_5500, Ricoh_Aficio_220, Ricoh_Aficio_270, Ricoh_Aficio_350, Ricoh_Aficio_450,
Ricoh_Aficio_550, Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP, Sharp_AR286_FN1,
Sharp_AR336_FN1, Sharp_AR405_FN1, Sharp_AR505_FN1, Sharp_AR286_FN2,
Sharp_AR336_FN2, Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070, Toshiba_eSTUDIO35,
Toshiba_eSTUDIO45, Toshiba_eSTUDIO55, Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR6_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING, SHORT_EDGE_BINDING)
PR6_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL, TOP_LEFT_VERTICAL,
TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT, TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR6_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR6_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR6_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR6_DC_COP. : 1
--- Printer7 Menu
PR7_OUT.
PR7_NAME.
: COM1 (NONE, LPT1, COM1, LPT2)
:
335
336
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
PR7_SCND.
: PR7 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR7_WAIT.
: YES
PR7_IN.
: AUTO (AUTO, NONE, COM1)
PR7_BEF.
:
PR7_STR.
:
PR7_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR7_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR7_AFT.
:
PR7_DUMP.
PR7_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR7_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR7_FORM.
: 66 0 100 60 30 50
PR7_FONT.
:
PR7_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605, Canon_IR3300,
Gestetner_3235, Gestetner_3245, Gestetner_3255, Gestetner_3265, Gestetner_P7032,
HP_LaserJet_5Si, Minolta_Di250, Minolta_Di350, Minolta_Di520, Minolta_Di620,
Minolta_PI_5500, Ricoh_Aficio_220, Ricoh_Aficio_270, Ricoh_Aficio_350, Ricoh_Aficio_450,
Ricoh_Aficio_550, Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP, Sharp_AR286_FN1,
Sharp_AR336_FN1, Sharp_AR405_FN1, Sharp_AR505_FN1, Sharp_AR286_FN2,
Sharp_AR336_FN2, Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070, Toshiba_eSTUDIO35,
Toshiba_eSTUDIO45, Toshiba_eSTUDIO55, Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR7_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING, SHORT_EDGE_BINDING)
PR7_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL, TOP_LEFT_VERTICAL,
TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT, TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR7_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR7_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR7_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR7_DC_COP. : 1
--- Printer8 Menu
PR8_OUT.
: COM1 (NONE, LPT1, COM1, LPT2)
PR8_NAME.
:
PR8_SCND.
: PR8 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR8_WAIT.
: YES
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
PR8_IN.
: AUTO (AUTO, NONE, COM1)
PR8_BEF.
:
PR8_STR.
:
PR8_CSET.
DEC>IBM)
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM,
PR8_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR8_AFT.
:
PR8_DUMP.
PR8_SIZE.
: NO
: A4 (A4, LETTER, LEGAL, EXECUT)
PR8_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR8_FORM.
: 66 0 100 60 30 50
PR8_FONT.
:
PR8_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605, Canon_IR3300,
Gestetner_3235, Gestetner_3245, Gestetner_3255, Gestetner_3265, Gestetner_P7032,
HP_LaserJet_5Si, Minolta_Di250, Minolta_Di350, Minolta_Di520, Minolta_Di620,
Minolta_PI_5500, Ricoh_Aficio_220, Ricoh_Aficio_270, Ricoh_Aficio_350, Ricoh_Aficio_450,
Ricoh_Aficio_550, Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP, Sharp_AR286_FN1,
Sharp_AR336_FN1, Sharp_AR405_FN1, Sharp_AR505_FN1, Sharp_AR286_FN2,
Sharp_AR336_FN2, Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070, Toshiba_eSTUDIO35,
Toshiba_eSTUDIO45, Toshiba_eSTUDIO55, Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR8_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING, SHORT_EDGE_BINDING)
PR8_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL, TOP_LEFT_VERTICAL,
TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT, TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR8_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR8_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR8_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR8_DC_COP. : 1
--- LPT1 Menu
L1_CENTR.
: HISPEED (IBM_PC, STNDRD, FAST, HISPEED, HINOACK)
L1_BSYTM.
: 60
L1_MGM_INFO. : AUTO (DISABLE, AUTO)
L1_COMMENT. :
L1_BIDIR.
L1_READT.
: AUTO (DISABLE, AUTO)
:3
337
338
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
--- COM1 Menu
C1_BAUDR.
: 9600 (300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200)
C1_NBITS.
: 8 (7, 8)
C1_PARIT.
: NONE (NONE, ODD, EVEN)
C1_STOPB.
: 2 (1, 2)
C1_HNDSH.
: ROBUST-BOTH (NONE, XON/XOFF, ROBUST, RDY/BSY, BOTH, ROBUST-BOTH)
C1_READT.
:3
C1_BSYTM.
: 60
C1_MGM_INFO. : AUTO (DISABLE, AUTO)
C1_COMMENT. :
--- LPT2 Menu
L2_CENTR.
: HISPEED (IBM_PC, STNDRD, FAST, HISPEED, HINOACK)
L2_BSYTM.
: 60
L2_MGM_INFO. : AUTO (DISABLE, AUTO)
L2_COMMENT. :
L2_BIDIR.
L2_READT.
: AUTO (DISABLE, AUTO)
:3
--- IBM IPDS Configuration
IPDS_COLSUP. : Disabled
IPDS_DUPSUP. : Enabled
IPDS_OPTDUP. : Enabled
IPDS_RAF.
: Disabled
IPDS_NUP.
: 1-up (1-up, 2-up, 4-up)
IPDS_OVLXOFF. : 0
IPDS_OVLYOFF. : 0
IPDS_RPTXOFF. : 0
IPDS_RPTYOFF. : 0
IPDS_DOB.
IPDS_DIB.
: Bin1 (Bin1, Bin2, Bin3, Bin4, Bin5, Bin6)
: Bin1 (Bin1, Bin2, Bin3, Bin4, Bin5)
PS_IPLINK. : Off (Off, Sheet, Bin)
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
IPDS_BIN1. : Letter, 0, 0
IPDS_BIN2. : Letter, 0, 0
IPDS_BIN3. : Letter, 0, 0
IPDS_BIN4. : Letter, 0, 0
IPDS_BIN5. : Letter, 0, 0
--- IBM IPDS PostScript Driver Settings
PS_LFSM.
: Enabled
PS_ERRH.
: Disabled
PS_OPTOVL. : Enabled
PS_G4SUP.
: Disabled
PS_VM.
: 2000
PS_BIN1.
: Default, 100, 100, 0, 0
PS_BIN2.
: Default, 100, 100, 0, 0
PS_BIN3.
: Default, 100, 100, 0, 0
PS_BIN4.
: Default, 100, 100, 0, 0
PS_BIN5.
: Default, 100, 100, 0, 0
PS_DEST.
: 0, 0, 0, 0, 0, 0
--- IBM IPDS PCL Driver Settings
PCL_VER.
: 5 (3, 4, 5)
PCL_SBSET. : AUTOMATIC (AUTOMATIC, US-ASCII, Latin1, Latin5, Latin9, PC437, PC850,
PC852, PC874, Roman8)
PCL_OCR_ENB. : Enabled
PCL_OPTOVL. : Disabled
PCL_BIN1.
: 8, 0, 0
PCL_BIN2.
: 1, 0, 0
PCL_BIN3.
: 4, 0, 0
PCL_BIN4.
: 5, 0, 0
PCL_BIN5.
: 0, 0, 0
PCL_DEST.
: 0, 0, 0, 0, 0, 0
--- IBM EMULATOR 1
339
340
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
IPDS_PREMUL1. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3, IPDS_3812_2,
IPDS_3812_2_00, IPDS_3816, IPDS_4028_1, IPDS_4028_2, IPDS_4312, IPDS_4317,
IPDS_4324, IPDS_4332)
IPDS_PRRES1. : 0
IPDS_SYSL1. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286,
287, 288, 289, 290, 293, 297, 361, 420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858,
860, 861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923, 924, 1004, 1026, 1069,
1140, 1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, 1252)
IPDS_PD1.
: PostScript (PostScript, PCL)
IPDS_SOJS1. :
IPDS_EOJS1. :
PREMUL1. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL1.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR1.
: NO
MPL1.
: 66, ENA
MPP1.
: 132, ENA
LPI1.
: 6 (3, 4, 6, 8)
CPI1.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI1.
AUTORI1.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
: YES
LM1.
: 0, 0, 48
TM1.
: 26, 26, 74
LDSF1.
: 94, 94, 70
DEFBIN1.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER1. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 2
IPDS_PREMUL2. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3, IPDS_3812_2,
IPDS_3812_2_00, IPDS_3816, IPDS_4028_1, IPDS_4028_2, IPDS_4312, IPDS_4317,
IPDS_4324, IPDS_4332)
IPDS_PRRES2. : 0
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
IPDS_SYSL2. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286,
287, 288, 289, 290, 293, 297, 361, 420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858,
860, 861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923, 924, 1004, 1026, 1069,
1140, 1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, 1252)
IPDS_PD2.
: PostScript (PostScript, PCL)
IPDS_SOJS2. :
IPDS_EOJS2. :
PREMUL2. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL2.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR2.
MPL2.
: NO
: 66, ENA
MPP2.
: 132, ENA
LPI2.
: 6 (3, 4, 6, 8)
CPI2.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI2.
AUTORI2.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
: YES
LM2.
: 0, 0, 48
TM2.
: 26, 26, 74
LDSF2.
: 100, 100, 70
DEFBIN2.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER2. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 3
IPDS_PREMUL3. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3, IPDS_3812_2,
IPDS_3812_2_00, IPDS_3816, IPDS_4028_1, IPDS_4028_2, IPDS_4312, IPDS_4317,
IPDS_4324, IPDS_4332)
IPDS_PRRES3. : 0
IPDS_SYSL3. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286,
287, 288, 289, 290, 293, 297, 361, 420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858,
860, 861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923, 924, 1004, 1026, 1069,
1140, 1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, 1252)
IPDS_PD3.
: PostScript (PostScript, PCL)
341
342
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
IPDS_SOJS3. :
IPDS_EOJS3. :
PREMUL3. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL3.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR3.
MPL3.
: NO
: 66, ENA
MPP3.
: 132, ENA
LPI3.
: 6 (3, 4, 6, 8)
CPI3.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI3.
AUTORI3.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
: YES
LM3.
: 0, 0, 48
TM3.
: 26, 26, 74
LDSF3.
: 100, 100, 70
DEFBIN3.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER3. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 4
IPDS_PREMUL4. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3, IPDS_3812_2,
IPDS_3812_2_00, IPDS_3816, IPDS_4028_1, IPDS_4028_2, IPDS_4312, IPDS_4317,
IPDS_4324, IPDS_4332)
IPDS_PRRES4. : 0
IPDS_SYSL4. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286,
287, 288, 289, 290, 293, 297, 361, 420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858,
860, 861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923, 924, 1004, 1026, 1069,
1140, 1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, 1252)
IPDS_PD4.
: PostScript (PostScript, PCL)
IPDS_SOJS4. :
IPDS_EOJS4. :
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
PREMUL4. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL4.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR4.
: NO
MPL4.
: 66, ENA
MPP4.
: 132, ENA
LPI4.
: 6 (3, 4, 6, 8)
CPI4.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI4.
AUTORI4.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
: YES
LM4.
: 0, 0, 48
TM4.
: 26, 26, 74
LDSF4.
: 100, 100, 70
DEFBIN4.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER4. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 5
IPDS_PREMUL5. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3, IPDS_3812_2,
IPDS_3812_2_00, IPDS_3816, IPDS_4028_1, IPDS_4028_2, IPDS_4312, IPDS_4317,
IPDS_4324, IPDS_4332)
IPDS_PRRES5. : 0
IPDS_SYSL5. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286,
287, 288, 289, 290, 293, 297, 361, 420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858,
860, 861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923, 924, 1004, 1026, 1069,
1140, 1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, 1252)
IPDS_PD5.
: PostScript (PostScript, PCL)
IPDS_SOJS5. :
IPDS_EOJS5. :
PREMUL5. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
343
344
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
SYSL5.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR5.
: NO
MPL5.
: 66, ENA
MPP5.
: 132, ENA
LPI5.
: 6 (3, 4, 6, 8)
CPI5.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI5.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI5.
: YES
LM5.
: 0, 0, 48
TM5.
: 26, 26, 74
LDSF5.
: 100, 100, 70
DEFBIN5.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER5. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 6
IPDS_PREMUL6. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3, IPDS_3812_2,
IPDS_3812_2_00, IPDS_3816, IPDS_4028_1, IPDS_4028_2, IPDS_4312, IPDS_4317,
IPDS_4324, IPDS_4332)
IPDS_PRRES6. : 0
IPDS_SYSL6. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286,
287, 288, 289, 290, 293, 297, 361, 420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858,
860, 861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923, 924, 1004, 1026, 1069,
1140, 1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, 1252)
IPDS_PD6.
: PostScript (PostScript, PCL)
IPDS_SOJS6. :
IPDS_EOJS6. :
PREMUL6. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL6.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR6.
MPL6.
: NO
: 66, ENA
AXIS 5570e/AXIS 5670e User’s Manual
MPP6.
Section 23: The Parameter List
: 132, ENA
LPI6.
: 6 (3, 4, 6, 8)
CPI6.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI6.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI6.
: YES
LM6.
: 0, 0, 48
TM6.
: 26, 26, 74
LDSF6.
: 100, 100, 70
DEFBIN6.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER6. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 7
IPDS_PREMUL7. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3, IPDS_3812_2,
IPDS_3812_2_00, IPDS_3816, IPDS_4028_1, IPDS_4028_2, IPDS_4312, IPDS_4317,
IPDS_4324, IPDS_4332)
IPDS_PRRES7. : 0
IPDS_SYSL7. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286,
287, 288, 289, 290, 293, 297, 361, 420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858,
860, 861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923, 924, 1004, 1026, 1069,
1140, 1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, 1252)
IPDS_PD7.
: PostScript (PostScript, PCL)
IPDS_SOJS7. :
IPDS_EOJS7. :
PREMUL7. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL7.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR7.
MPL7.
MPP7.
: NO
: 66, ENA
: 132, ENA
LPI7.
: 6 (3, 4, 6, 8)
CPI7.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI7.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
345
346
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
AUTORI7.
: YES
LM7.
: 0, 0, 48
TM7.
: 26, 26, 74
LDSF7.
: 100, 100, 70
DEFBIN7.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER7. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 8
IPDS_PREMUL8. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3, IPDS_3812_2,
IPDS_3812_2_00, IPDS_3816, IPDS_4028_1, IPDS_4028_2, IPDS_4312, IPDS_4317,
IPDS_4324, IPDS_4332)
IPDS_PRRES8. : 0
IPDS_SYSL8. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286,
287, 288, 289, 290, 293, 297, 361, 420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858,
860, 861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923, 924, 1004, 1026, 1069,
1140, 1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, 1252)
IPDS_PD8.
: PostScript (PostScript, PCL)
IPDS_SOJS8. :
IPDS_EOJS8. :
PREMUL8. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX,
3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,
3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL8.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,
289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR8.
MPL8.
MPP8.
: NO
: 66, ENA
: 132, ENA
LPI8.
: 6 (3, 4, 6, 8)
CPI8.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI8.
AUTORI8.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
: YES
LM8.
: 0, 0, 48
TM8.
: 26, 26, 74
LDSF8.
: 100, 100, 70
AXIS 5570e/AXIS 5670e User’s Manual
DEFBIN8.
Section 23: The Parameter List
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER8. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM SCS PAGE FORMAT
PCORI.
: NO
DWSISO.
: NO
BIN1.
: COR, LETTER, 0, 0
BIN2.
: COR, LETTER, 0, 0
BIN3.
: COR, LETTER, 0, 0
BIN4.
: COR, LETTER, 0, 0
BIN5.
: COR, LETTER, 0, 0
BIN6.
: COR, LETTER, 0, 0
MANUAL.
: COR, LETTER, 0, 0
ENVELOPE.
: COR, LETTER, 0, 0
CONTINUOUS. : COR, LETTER, 0, 0
SIMBF.
: YES
--- IBM SCS CPI MAPPING
FGID_DEFAULT. : 11
FGID_CPI5. : 244, 11
FGID_CPI10. : 11, 204
FGID_CPI12. : 86, 230
FGID_CPI15. : 230, 281
FGID_CPI17. : 252, 281
FGID_CPI8COR. : 86
FGID_CPI20COR. : 281
FGID_CPI25COR. : 289
FGID_CPI27COR. : 290
PROPOCOR.
TYPOCOR.
: 230
: 230
--- IBM SCS JOB CONTROL
REINIT.
: YES
347
348
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
SUPFFBLANK. : NO
--- IBM 3270 OPTIONS
CASE.
: DUAL (DUAL, MONO)
BASCOL.
: BLACK, ENA
XSTRN.
:0
AUTNL.
:1
ADDNL.
:1
FFWPB.
:0
FFEOPB.
:1
NULSUP.
:0
FFCPOS.
:0
AFEOPB.
:0
--- IBM SCS EXTENDED EMULATION
XEMUL.
: YES
WARN.
: NO
SSUBST.
: YES
SBTS.
TLIS.
:
: 025 03C
TTRS.
: 03E 025
FLIS.
: 025 02F
EECS.
COBXEM.
CCLIS.
: 025 041 058 049 053
: SETALL (OFF, SETESC, SETALL)
: 025 050
--- UDS
-------
--- BAR
NUMBER TYPE WIDTH HEIGHT TEXT-MODE CHECK-MODE
-------------------------------------------------------------
--- SSTR
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
--------
--- MSTR
--------
--- IBM PRINTER DRIVER
PRDRIVERBASE. : PCL5 (GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,
EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS)
SOJS.
: 1B 45 1B 26 6C 30 4C
EOJS.
: 1B 45
BACKSPS.
: 08
CRS.
: 0D
LFS.
: 0A
NLS.
: 0D 0A
FFS.
: 0C
SOS.
SIS.
BLKS.
:
:
:
GRNS.
:
BLUS.
:
REDS.
:
MAGS.
:
CYNS.
YELS.
:
:
BIN1S.
: 1B 26 6C 31 48
BIN2S.
: 1B 26 6C 34 48
BIN3S.
: 1B 26 6C 35 48
BIN4S.
: 1B 26 6C 32 30 48
BIN5S.
: 1B 26 6C 32 31 48
BIN6S.
: 1B 26 6C 32 32 48
MANUALS.
: 1B 26 6C 32 48
ENVELOPES. : 1B 26 6C 36 48
CONTINUOUSS. : 1B 26 6C 31 48
CSIZS.
:
349
350
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
LAC.
: HP_PCL (DISABLE, HP_PCL, EPSON_LQ)
GRD.
: HP_PCL (DISABLE, HP_PCL, EPSON_LQ)
JOGS.
: 1B 26 6C 31 54
SSUS.
:
SBSET.
: PC850 (ECMA94, LATIN9, PC437, PC850, PC852, PC857, PC858, PC874, PC891,
PC903, PC904, PC942, ROMAN8, USASCII, USER)
--- FONT
FGID CSSF SBSET SPACING PITCH HEIGHT STYLE STROKE TYPEFACE STRING
---------------------------------------------------------------------------------FONT.
: 3,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 5,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 11, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 12, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 13, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 18, 98, DEFAULT,FIXED, 100, 0,
ITALIC,MEDIUM,4099,
FONT.
: 19, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4200,
FONT.
: 20, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 30, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 38, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,BOLD, 4102,
FONT.
: 39, 98, DEFAULT,FIXED, 135, 0,
UPRIGHT,BOLD, 4102,
FONT.
: 40, 98, DEFAULT,FIXED, 135, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 41, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 42, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 43, 98, DEFAULT,FIXED, 100, 0,
ITALIC,MEDIUM,4099,
FONT.
: 46, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 60, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 66, 98, DEFAULT,FIXED, 150, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 68, 98, DEFAULT,FIXED, 150, 0,
ITALIC,MEDIUM,4102,
FONT.
: 69, 98, DEFAULT,FIXED, 150, 0,
UPRIGHT,BOLD, 4102,
FONT.
: 70, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 71, 98, DEFAULT,FIXED, 120, 0,
ITALIC,MEDIUM,4099,
FONT.
: 72, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 80, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 84, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,MEDIUM,4099,
1B 28 31 4F
1B 28 30 4F
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
FONT.
: 85, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 86, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 87, 98, DEFAULT,FIXED, 130, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 91, 98, DEFAULT,FIXED, 120, 0,
ITALIC,MEDIUM,4099,
FONT.
: 108, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 110, 98, DEFAULT,FIXED, 130, 0,
UPRIGHT,BOLD, 4102,
FONT.
: 111, 98, DEFAULT,FIXED, 120, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 112, 98, DEFAULT,FIXED, 120, 0,
ITALIC,MEDIUM,4099,
FONT.
: 155, 100, DEFAULT,PROP, 0,
110, ITALIC,BOLD, 4101,
FONT.
: 158, 100, DEFAULT,PROP, 0,
110, UPRIGHT,MEDIUM,4101,
FONT.
: 159, 100, DEFAULT,PROP, 0,
110, UPRIGHT,BOLD, 4101,
FONT.
: 160, 100, DEFAULT,PROP, 0,
110, UPRIGHT,MEDIUM,4148,
FONT.
: 162, 100, DEFAULT,PROP, 0,
110, ITALIC,MEDIUM,4148,
FONT.
: 163, 100, DEFAULT,PROP, 0,
110, UPRIGHT,BOLD, 4148,
FONT.
: 173, 100, DEFAULT,PROP, 0,
110, UPRIGHT,LIGHT, 4148,
FONT.
: 175, 100, DEFAULT,PROP, 0,
110, UPRIGHT,MEDIUM,4101,
FONT.
: 204, 98, DEFAULT,FIXED, 167, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 221, 98, DEFAULT,FIXED, 150, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 223, 98, DEFAULT,FIXED, 150, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 225, 98, DEFAULT,FIXED, 150, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 229, 98, DEFAULT,FIXED, 150, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 230, 98, DEFAULT,FIXED, 180, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 244, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 245, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 252, 98, DEFAULT,FIXED, 171, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 253, 98, DEFAULT,FIXED, 171, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 254, 98, DEFAULT,FIXED, 220, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 258, 98, DEFAULT,FIXED, 180, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 266, 98, DEFAULT,FIXED, 100, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 281, 98, DEFAULT,FIXED, 233, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 289, 98, DEFAULT,FIXED, 267, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 290, 98, DEFAULT,FIXED, 300, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 751, 100, DEFAULT,PROP, 0,
UPRIGHT,MEDIUM,4101,
80,
351
352
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
FONT.
: 1051, 100, DEFAULT,PROP, 0,
100, UPRIGHT,MEDIUM,4101,
FONT.
: 1053, 100, DEFAULT,PROP, 0,
100, UPRIGHT,BOLD, 4101,
FONT.
: 1056, 100, DEFAULT,PROP, 0,
100, ITALIC,MEDIUM,4101,
FONT.
: 1351, 100, DEFAULT,PROP, 0,
120, UPRIGHT,MEDIUM,4101,
FONT.
: 1653, 100, DEFAULT,PROP, 0,
160, UPRIGHT,BOLD, 4101,
FONT.
: 2103, 100, DEFAULT,PROP, 0,
240, UPRIGHT,BOLD, 4101,
FONT.
: 3840, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4101,
FONT.
: 3841, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4101,
FONT.
: 3842, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4101,
FONT.
: 3843, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4101,
FONT.
: 3844, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4113,
FONT.
: 3845, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4113,
FONT.
: 3846, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4113,
FONT.
: 3847, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4113,
FONT.
: 3848, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4116,
FONT.
: 3849, 100, DEFAULT,PROP, 0,
0,
NONE, MEDIUM,4140,
1B
28 73 34 53
FONT.
: 3850, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4148,
FONT.
: 3851, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4148,
FONT.
: 3852, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4148,
FONT.
: 3853, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4148,
FONT.
: 3854, 100, DEFAULT,PROP, 0,
0,
NONE, MEDIUM,4148,
0,
NONE, BOLD, 4148,
0,
NONE, MEDIUM,4148,
0,
NONE, BOLD, 4148,
1B
28 73 34 53
FONT.
: 3855, 100, DEFAULT,PROP, 0,
1B
28 73 34 53
FONT.
: 3856, 100, DEFAULT,PROP, 0,
1B
28 73 35 53
FONT.
: 3857, 100, DEFAULT,PROP, 0,
1B
28 73 35 53
FONT.
: 3858, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4168,
FONT.
: 3859, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4168,
FONT.
: 3860, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4168,
FONT.
: 3861, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4197,
AXIS 5570e/AXIS 5670e User’s Manual
Section 23: The Parameter List
FONT.
: 3862, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4197,
FONT.
: 3863, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4197,
FONT.
: 3864, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4197,
FONT.
: 3865, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4297,
FONT.
: 3866, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,NONE, 4362,
1B 28 73 31 42
FONT.
: 3867, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,NONE, 4362,
1B 28 73 34 42
FONT.
: 3868, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,16602,
FONT.
: 3869, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 16602,
FONT.
: 3870, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,16602,
FONT.
: 3871, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 16602,
FONT.
: 3872, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,16901,
FONT.
: 3873, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 16901,
FONT.
: 3874, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,16901,
FONT.
: 3875, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 16901,
FONT.
: 3876, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,16686, 1B 28 31 39 4D
FONT.
: 3877, 100, DEFAULT,PROP, 0, 0,
FONT.
: 5687, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,16901,
FONT.
: 5707, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 16901,
FONT.
: 5815, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,16901,
FONT.
: 5835, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 16901,
FONT.
: 6199, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4197,
FONT.
: 6219, 100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4197,
FONT.
: 6327, 100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4197,
FONT.
: 6347, 100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4197,
FONT.
: 16951,100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4101,
FONT.
: 16971,100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4101,
FONT.
: 17079,100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4101,
FONT.
: 17099,100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4101,
FONT.
: 33335,100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4113,
FONT.
: 33355,100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4113,
FONT.
: 33463,100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4113,
FONT.
: 33483,100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4113,
FONT.
: 33591,100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,16602,
UPRIGHT,MEDIUM,31402, 1B 28 35 37 39 4C
353
354
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
FONT.
: 33601,100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 16602,
FONT.
: 33719,100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,16602,
FONT.
: 33729,100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 16602,
FONT.
: 34103,100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4148,
FONT.
: 34123,100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4148,
FONT.
: 34231,100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4148,
FONT.
: 34251,100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4148,
FONT.
: 41783,100, DEFAULT,PROP, 0,
0,
UPRIGHT,MEDIUM,4116,
FONT.
: 41803,100, DEFAULT,PROP, 0,
0,
UPRIGHT,BOLD, 4116,
FONT.
: 41911,100, DEFAULT,PROP, 0,
0,
ITALIC,MEDIUM,4116,
FONT.
: 41931,100, DEFAULT,PROP, 0,
0,
ITALIC,BOLD, 4116,
FONT.
: 50000,100, PC942,PROP, 0,
144, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50001,100, PC942,PROP, 0,
144, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50002,100, PC942,PROP, 0,
120, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50003,100, PC942,PROP, 0,
108, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50004,100, PC942,PROP, 0,
96,
UPRIGHT,MEDIUM,28752, 1B
96,
UPRIGHT,MEDIUM,28752, 1B
80,
UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50005,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50006,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50007,100, PC942,PROP, 0,
101, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50008,100, PC942,PROP, 0,
101, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50009,100, PC942,PROP, 0,
84,
UPRIGHT,MEDIUM,28752, 1B
76,
UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50010,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
AXIS 5570e/AXIS 5670e User’s Manual
FONT.
: 50011,100, PC942,PROP, 0,
Section 23: The Parameter List
67,
UPRIGHT,MEDIUM,28752, 1B
67,
UPRIGHT,MEDIUM,28752, 1B
56,
UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50012,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50013,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50014,100, PC942,PROP, 0,
144, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50015,100, PC942,PROP, 0,
120, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50016,100, PC942,PROP, 0,
108, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50017,100, PC942,PROP, 0,
96,
UPRIGHT,MEDIUM,28752, 1B
80,
UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50018,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50019,100, PC942,PROP, 0,
101, UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50020,100, PC942,PROP, 0,
84,
UPRIGHT,MEDIUM,28752, 1B
76,
UPRIGHT,MEDIUM,28752, 1B
67,
UPRIGHT,MEDIUM,28752, 1B
56,
UPRIGHT,MEDIUM,28752, 1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50021,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50022,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50023,100, PC942,PROP, 0,
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50030,100, PC891,PROP, 0,
144, UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50031,100, PC891,PROP, 0,
144, UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50032,100, PC891,PROP, 0,
120, UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50033,100, PC891,PROP, 0,
108, UPRIGHT,MEDIUM,43088, 1B
355
356
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50034,100, PC891,PROP, 0,
96,
UPRIGHT,MEDIUM,43088, 1B
96,
UPRIGHT,MEDIUM,43088, 1B
80,
UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50035,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50036,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50037,100, PC891,PROP, 0,
101, UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50038,100, PC891,PROP, 0,
101, UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50039,100, PC891,PROP, 0,
84,
UPRIGHT,MEDIUM,43088, 1B
76,
UPRIGHT,MEDIUM,43088, 1B
67,
UPRIGHT,MEDIUM,43088, 1B
67,
UPRIGHT,MEDIUM,43088, 1B
56,
UPRIGHT,MEDIUM,43088, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50040,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50041,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50042,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50043,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50044,100, PC891,PROP, 0,
144, UPRIGHT,MEDIUM,41040, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50045,100, PC891,PROP, 0,
120, UPRIGHT,MEDIUM,41040, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50046,100, PC891,PROP, 0,
108, UPRIGHT,MEDIUM,41040, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50047,100, PC891,PROP, 0,
96,
UPRIGHT,MEDIUM,41040, 1B
80,
UPRIGHT,MEDIUM,41040, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50048,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50049,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
101, UPRIGHT,MEDIUM,41040, 1B
AXIS 5570e/AXIS 5670e User’s Manual
FONT.
: 50050,100, PC891,PROP, 0,
Section 23: The Parameter List
84,
UPRIGHT,MEDIUM,41040, 1B
76,
UPRIGHT,MEDIUM,41040, 1B
67,
UPRIGHT,MEDIUM,41040, 1B
56,
UPRIGHT,MEDIUM,41040, 1B
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50051,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50052,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50053,100, PC891,PROP, 0,
28 31 39 48 1B 26 74 33 38 50
FONT.
: 50060,100, PC904,PROP, 0,
144, UPRIGHT,MEDIUM,0,
FONT.
: 50061,100, PC904,PROP, 0,
144, UPRIGHT,MEDIUM,0,
FONT.
: 50062,100, PC904,PROP, 0,
120, UPRIGHT,MEDIUM,0,
FONT.
: 50063,100, PC904,PROP, 0,
108, UPRIGHT,MEDIUM,0,
FONT.
: 50064,100, PC904,PROP, 0,
96,
UPRIGHT,MEDIUM,0,
FONT.
: 50065,100, PC904,PROP, 0,
96,
UPRIGHT,MEDIUM,0,
FONT.
: 50066,100, PC904,PROP, 0,
80,
UPRIGHT,MEDIUM,0,
FONT.
: 50067,100, PC904,PROP, 0,
101, UPRIGHT,MEDIUM,0,
FONT.
: 50068,100, PC904,PROP, 0,
101, UPRIGHT,MEDIUM,0,
FONT.
: 50069,100, PC904,PROP, 0,
84,
UPRIGHT,MEDIUM,0,
FONT.
: 50070,100, PC904,PROP, 0,
76,
UPRIGHT,MEDIUM,0,
FONT.
: 50071,100, PC904,PROP, 0,
67,
UPRIGHT,MEDIUM,0,
FONT.
: 50072,100, PC904,PROP, 0,
67,
UPRIGHT,MEDIUM,0,
FONT.
: 50073,100, PC904,PROP, 0,
56,
UPRIGHT,MEDIUM,0,
FONT.
: 50074,100, PC904,PROP, 0,
144, UPRIGHT,MEDIUM,0,
FONT.
: 50075,100, PC904,PROP, 0,
120, UPRIGHT,MEDIUM,0,
FONT.
: 50076,100, PC904,PROP, 0,
108, UPRIGHT,MEDIUM,0,
FONT.
: 50077,100, PC904,PROP, 0,
96,
UPRIGHT,MEDIUM,0,
FONT.
: 50078,100, PC904,PROP, 0,
80,
UPRIGHT,MEDIUM,0,
FONT.
: 50079,100, PC904,PROP, 0,
101, UPRIGHT,MEDIUM,0,
FONT.
: 50080,100, PC904,PROP, 0,
84,
UPRIGHT,MEDIUM,0,
FONT.
: 50081,100, PC904,PROP, 0,
76,
UPRIGHT,MEDIUM,0,
FONT.
: 50082,100, PC904,PROP, 0,
67,
UPRIGHT,MEDIUM,0,
FONT.
: 50083,100, PC904,PROP, 0,
56,
UPRIGHT,MEDIUM,0,
FONT.
: 50100,100, PC903,PROP, 0,
144, UPRIGHT,MEDIUM,37058, 1B
357
358
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50101,100, PC903,PROP, 0,
144, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50102,100, PC903,PROP, 0,
120, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50103,100, PC903,PROP, 0,
108, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50104,100, PC903,PROP, 0,
96,
UPRIGHT,MEDIUM,37058, 1B
96,
UPRIGHT,MEDIUM,37058, 1B
80,
UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50105,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50106,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50107,100, PC903,PROP, 0,
101, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50108,100, PC903,PROP, 0,
101, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50109,100, PC903,PROP, 0,
84,
UPRIGHT,MEDIUM,37058, 1B
76,
UPRIGHT,MEDIUM,37058, 1B
67,
UPRIGHT,MEDIUM,37058, 1B
67,
UPRIGHT,MEDIUM,37058, 1B
56,
UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50110,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50111,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50112,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50113,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50114,100, PC903,PROP, 0,
144, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50115,100, PC903,PROP, 0,
120, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50116,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
108, UPRIGHT,MEDIUM,37058, 1B
AXIS 5570e/AXIS 5670e User’s Manual
FONT.
: 50117,100, PC903,PROP, 0,
Section 23: The Parameter List
96,
UPRIGHT,MEDIUM,37058, 1B
80,
UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50118,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50119,100, PC903,PROP, 0,
101, UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50120,100, PC903,PROP, 0,
84,
UPRIGHT,MEDIUM,37058, 1B
76,
UPRIGHT,MEDIUM,37058, 1B
67,
UPRIGHT,MEDIUM,37058, 1B
56,
UPRIGHT,MEDIUM,37058, 1B
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50121,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50122,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50123,100, PC903,PROP, 0,
28 31 38 43 1B 26 74 33 38 50
FONT.
: 50130,100, PC891,PROP, 0,
144, UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50131,100, PC891,PROP, 0,
144, UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50132,100, PC891,PROP, 0,
120, UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50133,100, PC891,PROP, 0,
108, UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50134,100, PC891,PROP, 0,
96,
UPRIGHT,MEDIUM,43088, 1B
96,
UPRIGHT,MEDIUM,43088, 1B
80,
UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50135,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50136,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50137,100, PC891,PROP, 0,
101, UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50138,100, PC891,PROP, 0,
101, UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50139,100, PC891,PROP, 0,
84,
UPRIGHT,MEDIUM,43088, 1B
359
360
Section 23: The Parameter List
AXIS 5570e/AXIS 5670e User’s Manual
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50140,100, PC891,PROP, 0,
76,
UPRIGHT,MEDIUM,43088, 1B
67,
UPRIGHT,MEDIUM,43088, 1B
67,
UPRIGHT,MEDIUM,43088, 1B
56,
UPRIGHT,MEDIUM,43088, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50141,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50142,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50143,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50144,100, PC891,PROP, 0,
144, UPRIGHT,MEDIUM,41040, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50145,100, PC891,PROP, 0,
120, UPRIGHT,MEDIUM,41040, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50146,100, PC891,PROP, 0,
108, UPRIGHT,MEDIUM,41040, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50147,100, PC891,PROP, 0,
96,
UPRIGHT,MEDIUM,41040, 1B
80,
UPRIGHT,MEDIUM,41040, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50148,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50149,100, PC891,PROP, 0,
101, UPRIGHT,MEDIUM,41040, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50150,100, PC891,PROP, 0,
84,
UPRIGHT,MEDIUM,41040, 1B
76,
UPRIGHT,MEDIUM,41040, 1B
67,
UPRIGHT,MEDIUM,41040, 1B
56,
UPRIGHT,MEDIUM,41040, 1B
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50151,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50152,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
FONT.
: 50153,100, PC891,PROP, 0,
28 31 38 48 1B 26 74 33 38 50
--- Email Menu
EMAIL_NOTIFICATION. : YES
REPLY_ADDRESS. :
AXIS 5570e/AXIS 5670e User’s Manual
PAPER_JAM_ADDRESS. :
OUT_OF_PAPER_ADDRESS. :
TONER_LOW_ADDRESS. :
NO_TONER_ADDRESS. :
PRINTER_OFFLINE_ADDRESS. :
Section 23: The Parameter List
361
362
Section 24: Glossary
Section 24
AXIS 5570e/AXIS 5670e User’s Manual
Glossary
Active Directory
Active Directory - a structure supported by Windows 2000 that lets
any object on a network be tracked and located. Active Directory is
the directory service used in Windows 2000 Server and provides the
foundation for Windows 2000 distributed networks.
3270DS
3270 Data Stream is a control language used for the 3270 family of
terminals and controllers. Also used for printing.
AIX
Advanced Interactive eXecutive. A version of the UNIX operating
system from IBM that runs on various IBM computers including
Mainframe systems.
APPC
Advanced Program-to-Program Communication. SNA facility (based
on LU6.2 and PU2.1) for general purpose inter-program
communications. Often used synonymously with LU6.2 but LU6.2 is
the architecture and APPC is the programming interface.
ARP
Address Resolution Protocol. A protocol within the TCP/IP suite of
network protocols that allows a host to find the physical address of a
node on the same network. It is available in UNIX, Windows 95,
Windows 98 and Windows NT. ARP cannot be used across routers.
ASCII
BOOTP
American Standard Code for Information Interchange, a plain text
format used by computers.
BOOT Protocol. A TCP/IP protocol, used for downloading start-up
information such as the IP address to hosts on the network. It is only
available in UNIX. BOOTP requires a BOOTP daemon on your system. A
request made to an active BOOTP daemon initiates a search of the
Boot Table for an entry matching the print server's Ethernet address.
If a matching entry is found, the daemon downloads the IP address to
the print server.
AXIS 5570e/AXIS 5670e User’s Manual
Section 24: Glossary
BSD
Berkeley Software Distribution. The University of California, Berkeley
additions to the UNIX operating system.
config file
This is a file that resides in the print server’s memory and contains all
the parameters that determine the AXIS 5570e/AXIS 5670e
functionality. By editing the config file (changing the parameter
settings), you can configure the AXIS 5570e/AXIS 5670e to meet the
printing needs of your network.
CPGID
Code Page Global ID
DHCP
Dynamic Host Configuration Protocol. DHCP is available in Windows
NT, NetWare 5 and UNIX systems, and allows for the automatic but
temporary assignment of IP addresses from a central pool. DHCP
causes the selected host to automatically allocate and download an
unused IP address to the requesting print server. It also provides
validation data that defines how long the IP addresses will remain
valid.
To fully benefit from this method, the AXIS 5570e/AXIS 5670e also
supports the WINS host name resolution protocol, which is available
in Windows NT networks.
DNS
Domain Name Service. Reflects the server names and addresses
within a network.
EBCDIC
Extended Binary Coded Decimal Interchange Code. Coded 8-bit
character set used by SNA and native IBM data streams.
FEP
Front End Processor. Generic term for a specialized computer linked
to a host machine to support a specialized function
(e.g. communications). IBM 3705, 3720, 3725, and 3745 are
communications FEPs.
363
364
Section 24: Glossary
Flash Memory
FTP
AXIS 5570e/AXIS 5670e User’s Manual
The print server software is stored in Flash Memory. This memory is
provided by a silicon chip that like any other ROM device, retains
data content even after power is removed. However, Flash Memory is
unique because it allows its data to be erased and re-written. This
means that you can install software updates for your server as soon as
they become available, without having to replace any parts. The new
software is simply loaded into the server over the network.
File Transfer Protocol. A TCP/IP protocol used for logging in to
network servers and for transferring files.
HPR
High Performance Routing. IBM implementation of APPN (Advanced
Peer-to-Peer Networking). Includes pro-active congestion control
and non-disruptive re-routing
HTML
Hypertext Markup Language. A standard hypertext language used for
creating World Wide Web pages and other hypertext documents.
HTTP
IBM
IP
IPDS
LED
Hypertext Transfer Protocol. The TCP/IP protocol for Web based
communication.
International Business Machines Corp.
Internet Protocol. The TCP/IP session-layer protocol that regulates
packet forwarding by tracking IP addresses, routing outgoing
messages and recognizing incoming messages.
Intelligent Printer Data Stream. An IBM protocol for data sent to
page printers. A page description language analogous to PostScript.
Light Emitting Diode.
AXIS 5570e/AXIS 5670e User’s Manual
Section 24: Glossary
Logical Printer
A logical printer acts as a filter between the network and the physical
printer. It appears to the user as a normal printer with additional
characteristics. For example a UNIX workstation may only send a line
feed (LF) to a shared printer that needs carriage return (CR) and LF.
The logical printer can solve this problem by adding a CR.
LPD
Line Printer Daemon protocol. A print server protocol widely used on
the Internet.
LPR
Line PRinter. The Unix print command. This does not actually print
files but rather copies or links them to a spool area from where a
daemon copies them to the printer.
LU
LU6.2
Logical Unit. The user's port into an SNA network. LU1 is a high
performance print stream. LU2 is a 3270 terminal data stream. LU3 is
a 3270 print data stream. LU6 is a host-to-host data exchange
stream. LU7 is the 5250 terminal data stream.
IBM Peer-to-peer data stream for NOS functions. Supports
asynchronous (store-and-forward) networking.
MIB
Management Information Base. A database of network configuration
information used by SNMP and CMIP to monitor or change network
settings.
NAU
Network Adressable Unit. Entities within an SNA network (SSCP, PU,
LU) that can send or receive requests and responses. An SNA network
is made up of NAUs and the underlying path control network.
NCP
NetWare Core Protocol. Network clients use the NCP to request
services of servers, and servers use NCP to provide services, such as
file and print services.
365
366
Section 24: Glossary
AXIS 5570e/AXIS 5670e User’s Manual
NCP(2)
Network Control Program. SNA program resident in the FEP. NCP offloads certain line protocol and routing functions from the host CPU.
NDS
PPR/PPD
PU
PU2.1
NetWare Directory Services. A hierarchical data base that manages
NetWare network resources such as servers and volumes.
Page Printer Requester/Page Printer Daemon. Bidirectional IBM
proprietary TCP/IP application protocol. Supported on AS/400s and
Mainframes for transporting IPDS printer data over TCP/IP. This is not
an open standard.
Physical Unit type within SNA. The software in an SNA node
controlling the node's communications hardware.
SNA PU type 2.1 allows local user ports to communicate without
going thorough a host node's SSCP services. RARP
Reverse Address Resolution Protocol. A TCP/IP protocol used for
downloading IP addresses in UNIX networks. It requires a RARP
daemon on your system, and only operates within a single network
segment. A request made to an active RARP daemon initiates a
search of the Ethernet Address Table for an entry matching the print
server's Ethernet address. If a matching entry is found, the daemon
downloads the IP address to the print server.
RISC
Reduced Instruction Set Computing. A processor that recognizes only
a limited number of assembly-language instructions.
SAP
Service Advertising Protocol. A NetWare network name advertising
service that e.g. file servers can use for advertising their existence to
network clients.
SAP(2)
Service Access Point. Field defined by the IEEE 802.2 specification
that is part of an address specification. Thus, the destination plus the
DSAP define the recipient of a packet. The same applies to the SSAP
AXIS 5570e/AXIS 5670e User’s Manual
Section 24: Glossary
SCS
SNA Character String. A sequence of control commands that allows
sophisticated control of printers and other devices.
SNA
Systems Network Architecture. IBM's data communications
architecture defining levels of protocols for communications between
terminals and applications as well as between programs. Originally
SNA was strictly host-based with VTAM controlling the network
except for path control which was provided by NCP in the FEP.
Recently, with the APPN/APPC and HPR additions SNA has become
more distributed.
SNMP
Simple Network Management Protocol. A TCP/IP protocol for
managing and monitoring nodes on a network.
SSCP
System Services Control Point. SNA software within VTAM which
handles network name/address conversion, device configuration,
network diagnostics and recovery. The SSCP is a NAU located on a
host node in the network.
TCP
Transmission Control Protocol. The connection-oriented, transportlevel protocol used in the TCP/IP suite of protocols.
TFTP
Trivial File Transport Protocol. A simpler version of the FTP protocol
that is used by the print server for the automatic downloading of
config files.
TN3270E
Extension to the Telnet protocol for transporting 3270 terminal and
print data over TCP/IP.
TN5250E
Extension to the Telnet protocol for transporting 5250 terminal and
print data over TCP/IP.
UNIX
A 32-bit multi-tasking, multi-user operating system originally
developed by AT&T.
367
368
Section 24: Glossary
AXIS 5570e/AXIS 5670e User’s Manual
URL
Uniform Resource Locator. A way of specifying the location of
publicly available information on the Internet.
VPDI
Virtual Printer Driver Interface
VTAM
Virtual Telecommunications Access Method. Mainframe software
that performs network control and management. VTAM's most
important objective is to provide the SSCP services.
WINS
Windows Internet Name Service. A NetBIOS Name Server that maps
NetBIOS names to dynamically assigned IP addresses.
Wizard
A special form of user assistance that automates a task through a
dialog with the user. Wizards help the user to accomplish tasks that
are complex and require experience.
AXIS 5570e/AXIS 5670e User’s Manual
Index
Numerics
3270DS 362
A
Account file 194, 195
Active Directory 362
Admin 181
AIX 362
APPC 362
AppleTalk 159
Approvals 294
AS/400 35
ASCII 362
ASCII to Postscript Conversion 225
Autodetect 160
Auto-Detect Printer Type 162
AutoIP 25, 206
AutoIP address structure 25
Axinstall 173
AXIS IPP Gateway Configuration 143
AXIS LPR Gateway Configuration 143
AXIS MIB 200
AXIS Print Monitor 114
AXIS Product CD 18
AXIS ThinWizard
Installing 189
B
Backside label 17
Bar Codes 251
Bar codes 252
Basic setup
AXIS NetPilot 149
BCP and TBCP 162
Bi-directional Printing 229
Bin
Default Input 273
Binary Protocol for Printer 162
369
370
AXIS 5570e/AXIS 5670e User’s Manual
BSD 363
C
Certificates 231
Delete 235
Import 234
View 235
Character Set Conversion 221
Checking SSL/TLS Status 235
Color 272
Concentrator gateway, general 248
Concentrator gateway, Microsoft 249
Concentrator gateway, NetWare 248
config file 180, 295, 363
Configuration and Management 18
Configuration methods
FTP 192
NetWare Administrator 156, 201
PCONSOLE 156, 201
SNMP 199
Telnet 195
Web browser 182
Configuration Mode 251
Configuring
AS/400 48
IBM Mainframes 61
Configutation Wizard 46, 68
Conversions 221, 222, 225
Copier Model 286
Copiers 292
CPI 255
Creating a Network Group 190
D
DBCS 279
Font Types 283
DDNS 33
Debugging 229
AXIS 5570e/AXIS 5670e User’s Manual
Hex Dump Mode 229
Print Problems 229
Default Input Bin 273
Delete Certificate 235
Device Features 282
DEVICE Statement 93
DHCP Enabled parameter 25
Digital Copier printing 287
Digital Copier Support 286
Dimensions 293
Disabling Protocols 234
DNS 363
DSPU 247
Duplex 272
Dynamic IP address Assignment 25
E
EBCDIC 363
Enable/disable SNMP 189
Enabling Protocols 234
Enabling SSL 231
Environmental 293
Ethernet Address 32
F
Factory Default 188
Factory default settings 288
FEP 363
Firmware
Upgrade 188
Firmware Upgrade 292
Flash Loading over the Web 230, 236
Flash Memory 364
Font
Smoothing 274
Font Selection 251
Fonts
Scalable 278
371
372
AXIS 5570e/AXIS 5670e User’s Manual
Selection 252
Typographical 278
Width 278
Front Panel 293
FSS Statement 89
FSSDEF Statement 92
FTP 192, 364
FTP_ENB 189
H
Hardware
293
Hardware Inventory 14
Hex Dump Mode 229
Hex Transparancy 252
Host Name 33
HPR 364
HTML 364
HTTP 364
HTTPS 234
I
IBM Capabilities 290
IBM Font Selection 255
IBM SNA 59
Importing a Certificate 234
Indicators 17, 18
Installation guide 22
Installation Summary 23
Installing AXIS ThinWizard 189
Internet Address 150
IP 364
IP Address
Automatic Assignment Methods 24
Manual Assignment Methods 24
Setting - Macintosh 163
Setting, using AutoIP 25
IPDS 364
AXIS 5570e/AXIS 5670e User’s Manual
IPP
Client 209
Printing Requirements 208
iPrint 123
L
Last Code Point 282
LLC 247
Local Printer 110
Logical Printer 365
Logical Printers 220, 291
Logon-mode Entry 63
LPD 177, 365
LPR 365
LU 365
LU6.2 365
M
Macintosh
Choosing a Printer 160
Installing the Print Server 159
MIB 365
Microsoft SNA 249
Mounting the AXIS 5570e 21
N
NAU 365
NCP 365
NCP(2) 366
NDPS 123, 124
NDS 151, 366
NetWare
Advanced installation 150
Basic installation 149
NDPS 124, 209, 210
NetWare Packet Signature 230
NetWare printing modes
Print Server Mode 155
373
374
AXIS 5570e/AXIS 5670e User’s Manual
Remote Printer Mode 155
NetWare SAA 248
Network
Indicator 17
Printer 110
Speed 230
Network Connection 292
Network Connector 17
Network Group
Create 190
Network Indicator 17
P
Paper Size
Physical 273
Parameter List 187, 295
Pass-through gateway 247
password 182
Point size 278
Ports 17
Power
Indicator 18
Power Consumption 293
PPR/PPD 366
Print Jobs
Redirect 227
Print Problems
Debugging 229
Print Server Management 292
Printer
Autodetect 160
Ports 17
Printer Connection 293
Printer Driver 46, 68
Printer Emulation 46, 68
Printing
Bi-directional 229
Parameter list 288
AXIS 5570e/AXIS 5670e User’s Manual
Test page 288
Protocols
Disable 234
Enable 234
Protocols and Datastreams 15
PRTnnnn Statement 89
PU 366
PU2.1 366
Pure IP 153
Q
Queue-based printing 123
R
Redirecting Print Jobs 227
Restart 187
RISC 366
S
SAP 366
SAP(2) 366
SBCS 283
SCS 367
SDLC 247
Secure Management 18
Secure Web Services 231
Security 292
Security Settings 187
Setting the Internet address
BOOTP 30
DHCP 32
RARP 29
Setting up
IBM SNA 35, 59
Macintosh 158
NetWare 123
UNIX 165
Windows 101
375
376
AXIS 5570e/AXIS 5670e User’s Manual
SNA 367
SNA Printing
3174 CU Mode 48
5494 CU Mode 36, 60
Snap-in for iPrint 143
SNMP 199, 367
SSCP 367
SSL 231
SSL/TLS
Status 235
Starting AXIS ThinWizard 189
Status file 194, 197
String Functions 222
String Substitutions 223, 251
Substitutions 223
Supported Printers 18, 290
Supported Protocols 291
Supported systems 291
Supported web browsers 291
Switched major node definitions 64
T
TCP 367
Technical Specifications 286, 290
Test Button 17
Test button 288
Test page 20
TFTP 30, 32, 367
TLS 231
TN3270E 367
TN3270E Printing 70
TN5250E 367
TN5250E Printing 48
U
UNIX 367
UNIX/Linux Printing Methods
FTP 177
AXIS 5570e/AXIS 5670e User’s Manual
LPD 177
PROS A 178
PROS B 178
Reverse Telnet 178
Upgrading 236
URL 368
User 181, 182
User Defined Strings 251
V
View Certificate 235
VTAM 368
VTAM Logon-mode entry 63
W
Web Flash Loading 230
WINS 32, 33
Wizard 368
World Wide Web 265
377
">