Extron electronics | Multi-Rate SDI Fiber Optic Transceiver FOX HD-SDI | User`s manual | Extron electronics Multi-Rate SDI Fiber Optic Transceiver FOX HD-SDI User`s manual

Extron electronics Multi-Rate SDI Fiber Optic Transceiver FOX HD-SDI User`s manual
User’s Manual
FOX HD-SDI
Multi-Rate SDI Fiber Optic Transceiver
www.extron.com
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort, The Netherlands
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
PM Industrial Bldg., Singapore 368363
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
© 2007 Extron Electronics. All rights reserved.
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
+81.3.3511.7655 FAX +81.3.3511.7656
68-1384-01 Rev. A
11 07
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Extron’s Warranty
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
1001 East Ball Road
Anaheim, CA 92805, USA
Asia:
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Europe, Africa, and the Middle East:
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Japan:
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
安全须知 • 中文
警告
这个符号提示用户该设备用户手册中
有重要的操作和维护说明。
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必须使用有地线的供电系统供电。 第三条线
(地线)是安全设施,不能不用或跳过。
这个符号警告用户该设备机壳内有暴
拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后
或桌面电源的电源线,或任何接到市电系统的电源线。
露的危险电压,有触电危险。
电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解所有安全和使用说明。
保存说明书 • 用户应保存安全说明书以备将来使
用。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没
有用户可以更换的零件。为避免出现触电危险不要自己
试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用与
厂家推荐的相同或相近型号的电池。 按照生产厂的建
议处理废弃电池。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备,以避免危险。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
N
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
Quick Start Guide — FOX HD-SDI
N The FOX HD-SDI is a transceiver that can function as a
transmitter and/or a receiver. At least two units are required
for a transmitter-receiver system with at least one fiber optic
cable linking each two units. The FOX HD-SDI is available in
single mode or multimode versions.
Connect and operate two or more FOX HD-SDI units as follows:
Step 1
Power off all equipment. If desired, mount the units in racks.
Step 2
MODE
MODE
MODE
Use the rear panel
1 down
1 down
1 up
Mode DIP switches
2 down
2 up
2 down
to configure each
1 2
1 2
1 2
unit to be installed
Bidirectional
Transmitter
Receiver with
in the system as
Transceiver
Loop-through
a bidirectional
transceiver, a transmitter, or a receiver as shown above right.
N The drawings below and on QS-2 show the signal flow for
the three different FOX HD-SDI configurations. For more
information on the various modes and their capabilities, see
"Transceiverconfigurations"in chapter 1, "Introduction".
Step 3
Transmitting unit — Connect an HD-SDI, SDI, or 3G-SDI
video source to the unit's HD/SDI In BNC connector.
HD/SDI IN
Step 4
Video
Transmitting unit —
Source
To Receiver
If the FOX HD-SDI
is configured as a
FOX HDSDI
transmitter, and if desired,
connect one or two local
monitors to the unit's
Buffered Outputs BNC
Transmitter
connectors. These two
BNCs output the same
HD-SDI, SDI, or 3G-SDI video that was input in step 3.
POWER
12V
0.3A MAX
Video from
Source
OPTICAL
MODE
HD/SDI IN
Tx
Rx
1
2
BUFFERED OUTPUTS
FOX HD-SDI • Quick Start Guide
Rx
Tx
Rx
Tx
OPTICAL
Both units — Connect
a fiber cable between
the transmitting unit's
Optical Tx connector
and the receiving unit's Optical Rx connector.
OPTICAL
Step 5
QS-1
Table of Contents
Quick Start Guide ­— FOX HD-SDI, cont’d
Chapter One • Introduction..................................................... 1-1
Step 6
About this Manual..................................................................... 1-2
About the FOX HD-SDI............................................................. 1-3
Receiving unit — Connect one or two monitors to the unit's Buffered
Outputs BNC connectors.
Video
Unit configured as
Source
bidirectional transceiver —
Both BNCs output
the HD-SDI, SDI, or
3G-SDI video that was
transmitted across the
fiber cable.
Bidirectional
POWER
12V
0.3A MAX
To/from 2nd
Transceiver
Transceiver configurations..................................................... 1-3
Video from 2nd
Transceiver
Bidirectional transceiver.........................................................1-3
Transmitter and receiver.........................................................1-4
FOX HDSDI
Features......................................................................................... 1-5
OPTICAL
MODE
1
HD/SDI IN
Tx
Rx
2
Chapter Two • Installation and Operation. .................. 2-1
BUFFERED OUTPUTS
Mounting the Unit..................................................................... 2-2
Transceiver
Unit configured as
receiver — Output 2 BNC
only outputs the
transmitted video.
Tabletop placement................................................................ 2-2
Rack mounting........................................................................ 2-2
Video from
Transmitter
Source
Daisy-chained
Receiver Transmitter
UL requirements......................................................................2-2
Mounting instructions............................................................2-3
FOX HDSDI
POWER
12V
0.3A MAX
Furniture mounting................................................................ 2-4
Through-desk mounting........................................................ 2-6
Projector mounting................................................................. 2-7
OPTICAL
MODE
HD/SDI IN
1
Tx
Rx
2
BUFFERED OUTPUTS
Receiver with
Loop-through
PMK 300 mounting..................................................................2-7
PMK 350 mounting. ................................................................2-9
Step 7
Connections and Settings...................................................... 2-11
Receiving unit — If desired, connect a fiber cable between the
receiving unit's Optical Tx connector and another unit's Optical Rx
connector.
Power supply wiring............................................................ 2-13
Operation.................................................................................... 2-14
Front panel indicators........................................................... 2-14
Unit configured as bidirectional transceiver — Connect the fiber
cable to the transmitting unit.
Fiber Compatibility Indications............................................ 2-14
System operation.................................................................. 2-15
Unit configured as a receiver — Connect the fiber cable to another
receiving unit for daisy chaining.
Appendix A • Reference Information..............................A-1
N Up to 10 receivers can be daisy-chained in this manner.
Specifications...............................................................................A-2
Part Numbers...............................................................................A-5
Step 8
Receiving unit configured as bidirectional transceiver —
Connect a video source to the unit's HD/SDI In BNC connector.
HD/SDI IN
Step 9
Transmitting unit configured as a bidirectional
transceiver — Connect one or two local monitors to the
unit's Buffered Outputs BNC connectors. These two
BNCs output the same video that was input in step 8.
Step 10
1
FOX HD-SDI part numbers......................................................A-5
Included parts.........................................................................A-5
Optional accessories...............................................................A-6
2
BUFFERED OUTPUTS
Connect power to all FOX units and to all connected video sources
and displays.
68-1384-01 Rev. A
11 07
All trademarks mentioned in this manual are the properties of their respective owners.
QS-2
FOX HD-SDI • Quick Start Guide
FOX HD-SDI • Table of Contents
Table of Contents, cont'd
FOX HD-SDI
1
Chapter One
Introduction
About this Manual
About the FOX HD-SDI
Features
ii
FOX HD-SDI • Table of Contents
Introduction
W
The FOX HD-SDI units output continuous,
invisible light, which may be harmful and
dangerous to the eyes; use with caution.
About the FOX HD-SDI
• Do not look into the rear panel fiber optic
The Extron FOX HD-SDI product family consists of two models
(MM and SM) of high performance digital (HD-SDI, SDI, or
3G-SDI) video fiber optic transceivers. The transmitted signal
can include any audio or unidirectional serial data that is
embedded in the input video.
• Plug the attached dust caps into the optical
N All transceivers in the system must be the same model (all
cable connectors or into the fiber optic cables,
themselves.
singlemode or all multimode).
transceivers when the fiber optic cable is
unplugged.
Transceiver configurations
About this Manual
The transceiver can be configured via its rear panel Mode DIP
switches to operate in one of three ways:
This manual contains information about the following Extron
FOX HD-SDI fiber optic transceiver products:
•
FOX HD-SDI MM, a multimode, long distance
(up to 500 m [1,640']) transceiver
•
FOX HD-SDI SM, a singlemode, very long distance
(up to 30 km [18.75 miles]) transceiver (figure 1-1)
•
•
•
Bidirectional transceiver
Transmitter
Receiver
N See item b, "Modeswitches",on page 2-11 to set the
configuration.
Bidirectional transceiver
Daisy Chain Numerous
Receivers
N In this manual, the term "transceiver" refers to any FOX
HD-SDI; the term "bidirectional transceiver" refers to a
FOX HD-SDI configured as described in this section.
AL
IC
OPT
C
FIG
ON
ED
ER
FF
BU
UTS SD
TP HD
OU OX
F
I
HD-SDI Broadcast
Monitors
N Although the description below does allow connection of
a FOX HD-SDI configured as transmitter or receiver,
the typical configuration is as shown: two bidirectional
transceivers.
Rx
Tx
Extron
FOX HD-SDI
X
V
12 MA
0.2A
H
DI
D/S
IN
Up to 30 km (18.75 miles)
on singlemode fiber using
SM Model
Fiber Optic
Transceiver
AL
IC
OPT
CO
G
NFI
ED
ER
FF
BU
UTS SD
TP HD
OU OX
F
I
A FOX HD-SDI that is configured as a bidirectional transceiver
(figure 1-2) inputs digital video on its SDI/HD-SDI Input BNC.
The transceiver converts the video input to a proprietary signal
and transmits the video over a fiber link to another FOX HD-SDI
that is configured as a bidirectional transceiver or as a receiver.
HD-SDI Broadcast
Monitors
Rx
Tx
Extron
FOX HD-SDI
X
V
12 MA
0.2A
HD
DI
/S
HD-SDI
In From
Source A
IN
Fiber Optic
Transceiver
FOX HDSDI
POWER
12V
0.3A MAX
HD-SDI Camera
1
Tx
Rx
2
BUFFERED OUTPUTS
HD-SDI HD-SDI
Out From Out From
Source A Source A
FOX HDSDI
POWER
12V
0.3A MAX
OPTICAL
MODE
HD/SDI IN
HD-SDI
In From
Source B
HD-SDI HD-SDI
Out From Out From
Source B Source B
OPTICAL
MODE
HD/SDI IN
1
Tx
Rx
2
BUFFERED OUTPUTS
Figure 1-1 — Typical FOX HD-SDI application
N The two products are physically and functionally identical,
with the exception of the effective range of transmission. In this manual, the term "FOX HD-SDI" refers to either
product.
1-2
FOX HD-SDI • Introduction
FOX HD-SDI
Configured as bidirectional transceiver
FOX HD-SDI
Configured as bidirectional transceiver
Figure 1-2 — Bidirectional transceiver connections
FOX HD-SDI • Introduction
1-3
Introduction, cont’d
A bidirectional transceiver can also simultaneously receive
a proprietary signal from another transceiver (in any
configuration) on its Optical Rx port, convert the proprietary
signal to back to the original format digital video, and output
the video on its own two Buffered Outputs BNC connectors.
Transmitter and receiver
N Although the description below does allow connection of a
FOX HD-SDI configured as a bidirectional transceiver, the
typical configuration is as shown: a transmitter and one or
more receivers.
A FOX HD-SDI that is configured as a transmitter (figure 1-3)
inputs digital video on its HD/SDI Input BNC. The transmitter
converts the video input to a proprietary signal and transmits
the video over a fiber link to a FOX HD-SDI that is configured as
a receiver or as a bidirectional transceiver. The transmitter also
simultaneously outputs the digital video on its two Buffered
Outputs BNCs.
FOX HD-SDI(s)
Configured as receiver(s)
HD-SDI
In From
Source A
HD-SDI HD-SDI
Out From Out From
Source A Source A
FOX HDSDI
POWER
12V
0.3A MAX
1
HD/SDI IN
Tx
Rx
Transmitted HD-SDI
from source A
FOX HDSDI
POWER
12V
0.3A MAX
OPTICAL
MODE
2
BUFFERED OUTPUTS
FOX HD-SDI
Configured as transmitter
HD-SDI
Out From
Source A
OPTICAL
MODE
HD/SDI IN
1
Tx
Rx
2
BUFFERED OUTPUTS
FOX HD-SDI
Configured as receiver
Figure 1-3 — Transmitter-to-receiver connections
A FOX HD-SDI that is configured as a receiver receives a
proprietary signal on its Rx fiber optic port. The receiver
converts the proprietary signal back to original HD-SDI, SDI,
or 3G-SDI video and outputs the video on only one of its own
Buffered Output BNC connectors, Output 2.
The receiver converts the second digital video signal that it
created from the optical input back into a proprietary signal
and outputs it on the Optical Rx port over a fiber link to another
FOX HD-SDI that is configured as a receiver or as a bidirectional
transceiver.
Features
Extends HD-SDI, SDI, and 3G-SDI signals very long distances
over a single fiber — The FOX HD-SDI supports multirate SDI at rates up to 2.97 Gbps, and complies with
SMPTE 259M-C, 292M, 424M, and ITU digital video
standards.
Video input — When it is configured as a transmitter, the
FOX HD-SDI inputs digital video on a BNC connector.
HD-SDI loop-through — The transceiver has two Buffered
SDI/HD-SDI BNC connectors that allows connection of
a local monitor when the transceiver is configured as a
transmitter.
Video output — The transceiver outputs digital video on one
or two Buffered SDI/HD-SDI BNC connectors when it is
configured as a bidirectional transceiver or a receiver.
Dual buffered outputs — When the FOX HD-SDI is configured
as a transmitter, the SDI/HD-SDI BNC output connectors
can be used for previewing the video on a local monitor.
Input equalization and reclocking on buffered outputs — The
FOX HD-SDI automatically equalizes incoming multirate SDI signals, and reshapes and restores signals on its
buffered outputs.
Daisy chain capability — Up to 10 transceivers can be daisy
chained to send the video to multiple locations when one
of more units are configured as receivers.
Real-time status LED indicators for troubleshooting and
monitoring
1" high, quarter rack width, metal enclosures — With low
profile enclosures, the transceiver can be discreetly
installed in a variety of locations, such as behind a plasma
or LCD flat-panel display.
Rack mountable — The unit is rack mountable in any
conventional 19" wide rack, using any of a variety of
Extron's rack shelves.
Power — The unit's 100 VAC to 240 VAC, external power supply
provides worldwide power compatibility.
N Up to 10 receivers can be daisy-chained in this manner.
1-4
FOX HD-SDI • Introduction
FOX HD-SDI • Introduction
1-5
Introduction, cont’d
FOX HD-SDI
2
Chapter Two
Installation and Operation
Mounting the Unit
Connections and Settings
Operation
1-6
FOX HD-SDI • Introduction
Installation and Operation
Mounting the Unit
C Installation and service must be performed by
authorized personnel only.
The 1" high, quarter-rack width transceiver can be placed on
a tabletop, mounted on a rack shelf, mounted under a desk or
tabletop, or mounted on a projector bracket.
Tabletop placement
Affix the four included rubber feet to the bottom of the unit and
place it in any convenient location.
Rack mounting
UL requirements
The following Underwriters Laboratories (UL) requirements
pertain to the installation of the FOX HD-SDI transmitter or
receiver into a rack (figure 2-1).
1.
Elevated operating ambient temperature — If installed in
a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater
than room ambient. Therefore, consider installing the
equipment in an environment compatible with the +122 °F
(50 °C) maximum ambient temperature (Tma) specified by
Extron.
2.
Reduced air flow — Installation of the equipment in a rack
should be such that the amount of air flow required for
safe operation of the equipment is not compromised.
3.
Mechanical loading — Mounting of the equipment in
the rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
4.
5.
2-2
Circuit overloading — Consideration should be given to
the connection of the equipment to the supply circuit and
the effect that overloading of the circuits might have on
overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be
used when addressing this concern.
Reliable earthing (grounding) — Reliable earthing
of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections
other than direct connections to the branch circuit (such as
the use of power strips).
FOX HD-SDI • Installation and Operation
Mounting instructions
For optional rack mounting, mount the transceiver on any of the
following rack shelves:
•
RSF 123 3.5" deep 1U VersaTools® rack shelf kit
(part #60-190-20) (figure 2-1)
•
RSB 123 3.5" deep 1U VersaTools rack shelf (part #60-604-20)
•
RSU 126 6" deep 1U universal rack shelf kit
(part #60-190-10)
•
RSB 126 6" deep 1U basic rack shelf (part #60-604-10)
•
RSU 129 9.5" deep 1U universal rack shelf kit
(part #60-190-01) (figure 2-2 on the next page)
•
RSB 129 9.5" deep 1U basic rack shelf (part #60-604-01)
VersaTools Rack Shelf
1/4 Rack Width Front
False Faceplate
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
Figure 2-1 — Mounting the transceiver on a
VersaTools rack shelf
On the non-VersaTools rack shelves, the transceiver unit can be
mounted in the front or the rear of the rack.
1.
If installed, remove the feet from the bottom of the unit.
2.
Mount the unit on the shelf, using two 4-40 x 3/16" screws
in opposite (diagonal) corners to secure the unit to the
shelf.
3.
Install false faceplate(s) or other unit(s) to the rack shelf.
4.
Insert the shelf into the rack, aligning the holes in the shelf
with those of the rack.
FOX HD-SDI • Installation and Operation
2-3
Installation and Operation, cont’d
1U Universal Rack Shelf
1/2 Rack Width
Front False
Faceplate
1/4 Rack Width
Front False
Faceplate
Both front false faceplates
use 2 screws.
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
Figure 2-2 — Mounting the transceiver on a standard
rack shelf
5.
Secure the shelf to the rack using the supplied machine
screws.
Figure 2-3 — Under-desk mounting
6.
Align the installed screws with the slots in the mounting
brackets, and place the transceiver against the surface,
with the screws through the bracket slots.
7.
Slide the transceiver slightly forward or back, then tighten
all four screws to fasten it in place.
Furniture mounting
The transceiver can be mounted under a horizontal surface using an
optional MBU 125 under-desk mounting kit (part #70-077-01).
Mount the unit under a desk or table as follows:
2-4
1.
If rubber feet were previously installed on the bottom of
the unit, remove them.
2.
Secure the under-desk mounting brackets to the
transceiver with the four machine screws provided in the
mounting kit (figure 2-3).
3.
Hold the transceiver with attached brackets against the
underside of the desk or other furniture. Mark the location
of holes for screws on the desk.
4.
Drill 1/4" (6.4 mm) deep, 3/32" (2 mm) diameter pilot
holes in the table or desk at the marked screw locations
from the underside or inside (the concealed side) of the
furniture, where the transceiver will be located.
5.
Insert the four wood screws into the pilot holes. Fasten
each screw into the installation surface until just less than
1/4" of the screw head protrudes.
FOX HD-SDI • Installation and Operation
FOX HD-SDI • Installation and Operation
2-5
Installation and Operation, cont’d
Through-desk mounting
The transceiver can be mounted through a desk or other
furniture using an optional Extron MBD 129 through-desk
mounting kit, part #70-077-02. Mount the transceiver through a
desk or table as follows (figure 2-4):
c. Tighten the screws.
d. Replace the unit inside the surface (step 4).
Projector mounting
The transceiver can be mounted on a projector bracket using
either of the following optional Extron projector mounting kits:
•
PMK 300 projector mounting kit (part #70-374-01)
•
PMK 350 low profile projector mounting kit
(part #70-563-02 [black] or part #70-563-03 [white])
PMK 300 mounting
Mount the transceiver to a PMK 300 bracket as follows:
1.
If necessary, remove the feet from the bottom of the
transceiver.
2.
Mount the transceiver to one of the bracket’s three
mounting plates using two of the supplied 4-40 x 3/16"
screws in opposite (diagonal) corners to secure the device
to the bracket. It can be vertically mounted facing either
up or down (figure 2-5).
N On the side mounting plates, the device is typically
mounted on the outside of the bracket.
On the front mounting plate, the device is typically
mounted on the inside of the bracket.
Figure 2-4 — Through-desk mounting
1.
Loosely attach the mounting brackets to the transceiver
using the four machine screws and washers supplied with
the mounting kit.
2.
Hold the transceiver against the inside of the surface
through which it will be mounted. Mark the four screw
holes on the inside of the surface to which you are
mounting the device.
3.
Drill four pilot holes, each 3/32" in diameter by 1/4" deep,
where you made marks.
4.
Using the provided four wood screws, secure the brackets
to the mounting surface.
5.
Slide the transceiver up and down in the mounting
brackets until the face of the transmitter or receiver is at
the desired height. Tighten the screws that secure the
brackets in place.
If the screws are inaccessible to a screwdriver:
Side Mounting
Plate
Bracket
Brace
U-Bolt
Extron
FOX 500 HDSDI
Transceiver
Power Supply
Extron
PMK 300
Multi-product Projector Mount Kit
Front Mounting
Plate
a. On the transceiver, mark the location of the brackets
relative to the screws.
b. Remove the transceiver from inside the furniture.
2-6
FOX HD-SDI • Installation and Operation
Figure 2-5 — PMK 300 projector mounting a transceiver
FOX HD-SDI • Installation and Operation
2-7
Installation and Operation, cont’d
3.
Use the two included tie wraps to strap the power supply
to one of the brackets.
N The PMK 300 has a hole in the bottom plate that allows the
projector pole to be inserted through the center of the plate
(figure 2-6), rather than outside of the plate (figure 2-5). To install the PMK 300 in this configuration, slide the
bracket up from the bottom of the pole before the projector
is installed on the pole.
PMK 350 mounting
Mount the transceiver to a PMK 350 bracket as follows:
1.
Remove the front and back plates from the PMK 350
(figure 2-7), using an Extron Tweeker or a #2 Philips
screwdriver. Retain the screws to reattach the plates when
you are finished.
Extron
Quarter-rack
Sized Product
Rear Plate
Bracket
Brace
Contoured
Base
L-shaped
Bracket
U-Bolt
Extron
PMK 300
Multi-product Projector
Mount Kit
Extron
PMK 350
U-bolt
Multi-product Projector
Mounting Kit
Extron
Power Supply
Front Plate
Cover Sheet
Figure 2-7 — PMK 350 projector mounting a
transceiver
2.
If necessary, remove the feet from the bottom of the
receiver.
3.
Secure the transceiver to one side of the mounting tray,
using two of the supplied 4-40 x 3/16" screws in opposite
(diagonal) corners.
4.
Use the two included tie wraps to strap the power supply
to the bracket.
5.
Place the PMK 350 around the projector ceiling mounting
pole (figure 2-7, above).
Figure 2-6 — Projector pole on the inside
4.
Place the contoured bracket brace against the pole and
opposite the back plate. The pole should fit snugly into the
depression in the center of the bracket brace.
5.
Place the U-bolt around the ceiling pole and insert the
two legs of the U-bolt through the round holes on the
contoured bracket brace and then through the slotted holes
on the bracket’s mounting plate.
N The supplied U-bolt fits a typical (1.5" to 2.0" diameter)
ceiling pole.
6.
2-8
Secure the bracket to the U-bolt with the included hex
nuts, washers, and lock washers. Tighten the hex nuts just
enough that they can be loosened by hand.
FOX HD-SDI • Installation and Operation
FOX HD-SDI • Installation and Operation
2-9
Installation and Operation, cont’d
Assemble the U-bolt and the following parts in the
following order (figure 2-8):
6.
Connections and Settings
All connectors are on the rear panel (figure 2-9).
Mount Plate
Flange
FOX HDSDI
POWER
12V
0.3A MAX
Contoured
Base
OPTICAL
MODE
U-bolt
L-shaped
Bracket
Slotted Hole
in PMK Tray
5
L-shaped
Bracket Screws
Ceiling
Pole
Figure 2-8 — Hanging the tray on the pole
a. Pass the legs of the U-bolt through the slotted holes on
the mount plate flange.
a
b
d. Pass the U-bolt legs through the holes in the L-shaped
bracket.
8.
Move the PMK 350 up to the desired location on the ceiling
pole, as close to the ceiling as desired.
9.
1 2
c
11. If desired, choose one of the provided four sizes of selfadhesive cover sheets, and apply it to the underside of the
mounting tray.
2-10
FOX HD-SDI • Installation and Operation
Bidirectional transceiver (default position)
Down
Up
Transmitter with local monitor outputs
Up
Down
Up
Up
Receiver with daisy chaining
Spare (functions as receiver with daisy chaining)
Fiber optic connectors —
This unit outputs continuous invisible light, which
may be harmful and dangerous to the eyes; use with
caution. For additional safety, plug the attached
dust caps into the optical transceivers
OPTICAL
when the fiber optic cable is unplugged.
N Ensure that you use the proper fiber cable for
your transceivers. Typically, singlemode fiber
cable has a yellow jacket and multimode fiber
cable has an orange jacket. Also, see "Fiber
CompatibilityIndications"on page 2-14 to
determine the transceiver's compatibility.
N Be sure to tighten the hex nuts securely enough that the
10. Secure the front panel to the mounting tray with four of
the included #6 screws.
Down Down
W
Secure the L-shaped bracket to the U-bolt using the
included hex nuts, washers, and lock washers. Tighten the
hex nuts securely.
PMK 350 does not slide down the ceiling pole. A socket
wrench is recommended to tighten the hex nuts.
4
Mode switches — Set these DIP switches to the positions shown
in the table below to select the transceiver configuration. See
"Transceiver configurations" on page 1-3 for more information.
of the contoured base.
Align the two slotted holes in the bottom of the L-shaped
bracket with the two slotted holes in the base of the tray.
Secure the L-shaped bracket to the base by inserting two
provided 6-32 x 5/16" screws through the aligned slots.
3
2
2
BUFFERED OUTPUTS
HD-SDI Input connector — If the FOX HD-SDI is configured
as either a bidirectional transceiver or as a transmitter, connect
an HD-SDI, SDI, or 3G-SDI video input to this BNC connector.
MODE
N The pole fits snugly into the depression in the center
7.
1
Rx
SW1 SW2 Mode
c. Pass the legs through the holes in the contour base.
diameter) ceiling pole.
Tx
Figure 2-9 — FOX HD-SDI transceiver’s connectors
b. Place the legs around the projector pole.
N The supplied U-bolt fits a typical (1.5" to 2.0"
1
1 2
HD/SDI IN
Tx — In any FOX HD-SDI configuration, for all oneway HD-SDI, SDI, or 3G-SDI transmission, connect a
fiber optic cable to the Optical Tx LC connector.
Connect the free end of this fiber optic cable
to the Optical Rx connector on another
FOX HD-SDI transceiver that is configured as a
bidirectional transceiver or as a receiver.
FOX HD-SDI • Installation and Operation
Tx
Rx
OPTICAL
Tx
Rx
2-11
Installation and Operation, cont’d
Rx — If the FOX HD-SDI is configured as a bidirectional
transceiver or as a receiver, for one-way communications
from the transmitting unit, connect a fiber optic cable to the
Optical Rx connector.
If the FOX HD-SDI is configured as a bidirectional transceiver,
If the FOX HD-SDI is configured as a receiver, connect the
d
e
connect the free end of this fiber optic cable to the Optical Tx
connector on the transmitting FOX HD-SDI.
Power supply wiring
Figure 2-10 shows how to wire the power connector.
Smooth
Ridges
A
A
free end of this fiber optic cable to the Optical Tx connector
on the next FOX HD-SDI in the daisy chain.
Power Supply
Output Cord
SECTION A–A
Tie Wrap
Buffered Outputs connectors — In any FOX HD-SDI
configuration, connect a digital display to these BNC
connectors. See "Transceiver configurations" on page 1-3 for
more details.
If the FOX HD-SDI is configured as a bidirectional transceiver,
the video is output on both connectors 1 and 2 and is the video
signal sent from the other transceiver.
If the FOX HD-SDI is configured as a receiver, the video
is output on connector 2 only and is the video sent by the
transmitting unit.
If the FOX HD-SDI is configured as a transmitter, the video is
output on both connectors 1 and 2 and is looped through from
the same transceiver's HD/SDI Input connector, item a.
Power connector — Plug the included external 12 VDC
power supply into this 2-pole captive screw connector.
See “Power supply wiring”, on the next page, to wire the
connector.
5
3
Captive Screw
Connector
Figure 2-10 — Power connector wiring
C
Power supply voltage polarity is critical. Incorrect
voltage polarity can damage the power supply
and the FOX HD-SDI. Identify the power cord
negative lead by the ridges on the side of the cord
(figure 2-10).
To verify the polarity before connection, plug in the power
supply with no load and check the output with a voltmeter.
W
The two power cord wires must be kept separate
while the power supply is plugged in. Remove
power before wiring.
C
The length of the exposed (stripped) copper wires
is important. The ideal length is 3/16" (5 mm). Longer bare wires can short together. Shorter wires
are not as secure in the connectors and could be
pulled out.
N Do not tin the power supply leads before installing them
in the connector. Tinned wires are not as secure in the
connectors and could be pulled out.
Use the supplied tie-wrap to strap the power cord to the
extended tail of the connector.
Alternatively, an optional Extron PS 123 Universal 12 VDC
Power Supply, part #60-814-01, can power multiple Extron
12 VDC devices using only one AC power connector.
2-12
FOX HD-SDI • Installation and Operation
FOX HD-SDI • Installation and Operation
2-13
Installation and Operation, cont’d
Operation
System operation
Front panel indicators
All indicators are on the front panel (figure 2-13).
270
Mbps
RATE
1.485
Gbps
2.97
Gbps
After the transmitting and receiving units and all of their
connected devices are powered up, the system is fully
operational. If any problems are encountered, ensure all
traditional and fiber cables are routed and connected properly.
UNKNOWN
FOX HDSDI
1
2
Figure 2-13 — FOX HD-SDI's transceiver’s indicators
a
b
Power indicator — When lit, this light emitting diode (LED)
indicates that the FOX HD-SDI transceiver is receiving power.
Rate indicators — These LEDs light to indicate the detected
input video rate, either on the HD/SDI input BNC (if configured
as a transmitter) or on the Optical Rx connector (if configured as
a receiver or bidirectional transceiver). The recognized rates are
270 Mbps, 1.485 Gbps, or 2.97 Gbps.
When the Rate Unknown LED lights, this indicates that an input
is detected, either on the HD/SDI input BNC (if configured as
a transmitter) or on the Optical Rx connector (if configured as a
receiver or bidirectional transceiver), but that the FOX HD-SDI
does not recognize the rate.
N All four Rate LEDs blink repeatedly if a fiber optic
connector module on the rear of the unit is unseated.
N The FOX HD-SDI equalizes and distributes the input
whether it recognizes the rate or not.
Fiber Compatibility Indications
You must use the proper fiber cable for your transceivers.
Each transceiver indicates its fiber compatibility, singlemode or
multimode, at power-up by blinking the four Rate indicators.
•Multimode — The Rate LEDs blink once.
•Singlemode — The Rate LEDs blink twice.
N To determine the fiber cable type, observe the cable jacket. Typically, singlemode fiber cable has a yellow jacket and
multimode fiber cable has an orange jacket.
N All transceivers in the system must be the same model (all
singlemode or all multimode). Mixed transmission mode
units will not work together.
2-14
FOX HD-SDI • Installation and Operation
FOX HD-SDI • Installation and Operation
2-15
Installation and Operation, cont’d
FOX HD-SDI
A
Appendix A
Reference Information
Specifications
Part Numbers
2-16
FOX HD-SDI • Installation and Operation
Reference Information
Specifications
N
The FOX HD-SDI is a transceiver that can function as a
transmitter and/or as a receiver. Two units are required for a
transmitter-receiver system with one fiber optic cable linking
the two units. The FOX HD‑SDI is available in single mode or
multimode versions.
N
These transceivers are class 1 laser products. They meet the
safety regulations of IEC-60825, FDA 21, CFR 1040.10, and
FDA 21 CFR 1040.11.
Optical fiber interconnection between transmitter and
receiver
Number/type................................. 1 fiber optic
N
Only one fiber is required to transmit video and embedded audio
and unidirectional data.
Connectors...................................... 1 LC connector
Operating distance......................... 30 km (18.75 miles) with singlemode (SM)
cables with a FOX HD‑SDI SM
500 m (1640’) with multimode (MM)
cables with a FOX HD‑SDI MM
N
Operating distance is approximate. These are typical
distances. The maximum distance may be greater than these
typical numbers depending on factors such as fiber type, fiber
bandwidth, connector splicing, losses, modal or chromatic
dispersion, environmental factors, and kinks.
Nominal peak wavelength........... 850 nm for FOX HD‑SDI MM,
1310 nm for FOX HD‑SDI SM
Transmission power
Singlemode.......................... -5 dBm, typical
Multimode........................... -5 dBm, typical
Maximum receiver sensitivity
Singlemode.......................... -18 dBm, typical
Multimode........................... -12 dBm, typical
Optical loss budget
Singlemode.......................... 13 dB, maximum
Multimode........................... 7 dB, maximum
A-2
FOX HD-SDI • Reference Information
Video
Signal type....................................... HD-SDI, SDI, and 3G-SDI digital video
signals
Gain ................................................. Unity
Resolution....................................... 8 or 10 bits, automatic
Data rates......................................... 270 Mbps, 1.485 Gbps, 2.970 Gbps
Operation standards...................... SMPTE 259M-C, SMPTE 292M,
SMPTE 424M, ITU‑R BT.601,
ITU‑R BT.1120, DVB‑ASI
Auto data rate lock......................... Yes
Video input— transmitter
Number/signal type...................... 1 single link SDI, HD-SDI, or 3G-SDI
digital component video
Connectors ..................................... 1 female BNC
Data rates......................................... 19 Mbps to 2.97 Gbps
Nominal level................................. 0.8 Vp-p
Minimum/maximum levels......... 0.5 V to 1 Vp-p with no offset
Impedance . .................................... 75 ohms
Return loss ..................................... <-15 dB @ 5 MHz to 2.97 GHz
DC offset (max. allowable)........... 5 V
Input coupling................................ AC
Input cable equalization................ Automatic for up to -30 dB of cable loss
HD-SDI................................ 120 m (400’) using Extron RG6 cable
90 m (300’) using Extron RG59 cable
SDI........................................ 150 m (500’) using Extron RG6 cable
120 m (400’) using Extron RG59 cable
N
The transmission distance varies depending on the signal
resolution and on the type of cable, graphic card, and display
used in the system.
Video output — receiver
Number/signal type......................
digital component video
Connectors ..................................... 2 female BNC
Reclocking....................................... Automatic for 270 Mbps, 1.485 Gbps,
2.97 Gbps, or bypassed for unrecognized
rates
Nominal level................................. 0.8 Vp-p
Minimum/maximum levels......... 0.5 V to 1.0 Vp-p
Impedance . .................................... 75 ohms
FOX HD-SDI • Reference Information
A-3
Reference Information, cont’d
Return loss ..................................... <-25 dB @ 100 MHz
DC offset . ....................................... ±5 mV with input at 0 offset
General
External power supply ................. 100 VAC to 240 VAC, 50/60 Hz, 6 watts,
external; to 12 VDC, 2 A, regulated
Power input requirements............ 12 VDC, 0.3 A
Temperature/humidity................. Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Cooling............................................ Convection, unvented
Rack mount..................................... Yes, with optional 1U, 9.5” deep rack shelf,
part #60-190-01 or 60-604-01;
1U, 6” deep rack shelf, part #60-190-10,
60-604-10;
or VersaTools® 1U, 3” deep rack shelf, part
#60-190-20 or 60‑604‑20.
Also furniture mountable with optional
Through-Desk Mounting Kit, #70-077-02,
or Under-Desk Mounting Kit, #70-077-01;
or attachable to a projector mount using
optional kit #70-526-02 or 70-077-04.
Enclosure type ............................... Metal
Enclosure dimensions.................... 1.0” H x 4.3” W x 3.0” D
(quarter rack wide)
2.5 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.)
Product weight............................... 0.5 lb (0.3 kg) per each unit
Shipping weight ............................ 3 lbs (2 kg) per each unit
Vibration . ....................................... ISTA 1A in carton
(International Safe Transit Association)
Listings............................................ UL, CUL
Compliances.................................... CE, FCC Class A, VCCI, AS/NZS, ICES,
FDA Class 1
MTBF................................................ 30,000 hours
Warranty . ....................................... 3 years parts and labor
N
All nominal levels are at ±10%.
N
Specifications are subject to change without notice.
A-4
FOX HD-SDI • Reference Information
Part Numbers
FOX HD-SDI part numbers
N The FOX HD-SDI is a transceiver that can function as
a transmitter and/or as a receiver. At least two units are
required for a transmitter-receiver system with one fiber
optic cable linking the two units.
Additional transceivers configured as receivers can be
added to the system for daisy-chaining.
The FOX HD-SDI is available in singlemode (SM) and
multimode (MM) models:
FOX HD-SDI Models
Part number
FOX HD-SDI SM
60-901-01
FOX HD-SDI MM
60-900-01
Included parts
These items are included in each order for a FOX HD-SDI:
Included parts
12 VDC power supply
Replacement
part number
70-055-01
Tweeker (small screwdriver)
User’s guide
(1) 10' LC-LC duplex patch cables
(SM or MM, depending on the model)
FOX HD-SDI • Reference Information
A-5
Reference Information, cont’d
Optional accessories
Accessories
Part number
RSU 129 9.5" 1U universal rack shelf kit
60-190-01
RSB 129 9.5" 1U basic rack shelf
60-604-01
RSU 126 6" deep 1U universal rack shelf kit
60-190-10
RSU 126 6" deep 1U universal rack shelf
60-604-10
RSF 123 3.5" deep 1U VersaTools
rack shelf kit
60-190-20
RSB 123 3.5" deep 1U VersaTools
rack shelf
60-604-20
MBD 129 through desk mounting kit
70-077-02
PMK 300 projector mounting kit
70-374-01
®
PMK 350 low profile projector mounting kit,
black (white)
A-6
FOX HD-SDI • Reference Information
70-563-02 (03)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising