Samsung Techwin SND-3080CF network camera User Manual

Below you will find brief information for network camera SND-3080CF. The SND-3080CF is a network camera that allows you to monitor your home or business remotely. You can connect the camera to your network and view live video on your computer or mobile device. The camera features a number of useful features, including:

PDF Download

Document

NETWORK CAMERA
User Manual
SND-3080CF
Network Camera
User Manual
Copyright
&copy;2010 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this
document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of
Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but
no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on
the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document
without prior notice.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve
the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
• If the system behaves abnormally because you run a program irrelevant to the system operation.
• Deteriorated performance or natural worn-out in process of time
overview
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of
electric shock is present within this unit.
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this unit.
WARNING
y To reduce the risk of fire or electric shock, do not expose this appliance to rain or
moisture.
y To prevent injury, this apparatus must be securely attached to the floor/wall in accordance
with the installation instructions.
y If this power supply is used at 24V ac, a suitable plug adapter should be used.
y The camera is to be only connected to PoE networks without routing to the outside plant.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause
abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may
cause fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause
personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or
containers filled with water on top of the camera. Doing so may cause personal injury
due to fire, electric shock, or falling objects.
English _3
● OVERVIEW
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER
overview
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or
electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such
case, immediately disconnect the power source and contact the service center.
Continued use in such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never
disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused
by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may
cause fire or electric shock
11. Do not expose the product to the direct airflow from an air conditioner.
Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature
difference between internal and external of the dome camera.
12. If you install this product in a low-temp area such as inside a cold store, you must seal
up the wiring pipe with silicon, so that the external air can not flow inside the housing.
Otherwise, external high, humid air may flow inside the housing, pooling moisture or
vapor inside the product due to a difference between internal and external temperature.
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a
location subject to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50&deg;C), low temperature
(below -10&deg;C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and
then move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do
so may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this
may damage the CCD image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any
time.
10. When using the camera outdoors, moisture may occur inside the camera due
to temperature difference between indoors and outdoors. For this reason, it is
recommended to install the camera indoors. For outdoor use, use the camera with builtin fan and heater.
4_ overview
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions :
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may cause
undesired operation.
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian
Interference.-Causing Equipment Regulations of ICES-003.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
English _5
● OVERVIEW
CAUTION
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his
own expense.
overview
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as powersupply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus
6_ overview
CONTENTS
Important Safety Instructions
Product Features
Recommended PC Specifications
What’s Included
At a Glance
INSTALLATION &amp;
CONNECTION
14
15
14
16
Instalation
Inserting/Removing an SD
Memory Card
Memory Card Information (not
included)
Connecting with Other Device
CAMERA SETUP
20
20
21
21
22
27
28
29
NETWORK CONNECTION
AND SETUP
30
30
31
3
17
32
33
34
35
38
39
40
40
How to Use the Keyboard
Controller
Main Menu
Profile
Camera Setup
Privacy Zone
Others
System Info
Connecting the Camera to an
IP Router with the xDSL/Cable
Modem
Connecting the Camera to an IP
Router With Local Area Networking
Connecting the Camera Directly
to a DHCP-Based xDSL/Cable
Modem
Connecting the Camera Directly
to Local Area Networking
Buttons Used in IP Installer
Static IP Setup
Dynamic IP Setup
Port Range Forward (Port Mapping)
Setup
Connecting to the camera from a
shared local PC
Connecting to the camera from a
remote PC via the Internet
English _7
● OVERVIEW
6
9
9
10
11
OVERVIEW
overview
WEB VIEWER
41
SETUP SCREEN
49
APPENDIX
71
8_ overview
41
42
43
44
45
47
48
Connecting to the Camera
Login
Installing Activex
Using the Live Screen
Backup
Checking the Object Counting
Using the SD Search Viewer
Screen
49
50
55
58
59
70
Accessing the Setup Screen
Default Setup
System Setup
Overlay Setup
Event Setup
Network Setup
71
72
73
77
83
89
91
Profile
Terminology
Specifications
Frame Rate (NTSC)
Frame Rate (PAL)
Troubleshooting
GPL/LGPL Software License
PRODUCT FEATURES
RECOMMENDED PC SPECIFICATIONS
y CPU : Pentium4 / 2.4GHz or higher
y Operating System : Windows XP(Service Pack2, Service Pack3) / Windows Vista /
Windows 7
y Resolution : 1024X768 pixels or higher
y RAM : 512MB or higher
y Web Browser : Internet Explorer 6.0 or higher
y Video Card : Radeon, Nvidia
y Video Memory : 128MB
y DirectX 8.1 or higher
Compatible IP Routers
y Linksys
y D-Link
y Netgear
Compatible PoE Switches
y Linksys SRW224G4P
y D-Link DES-1316
y SMC SMCPWR-INJ3
English _9
● OVERVIEW
y Support various communication protocols
Supports TCP/IP, UDP, RTP/RTSP, SMTP for email, and FTP protocols as well as various
internet protocols such as ARP, HTTP, HTTPS and DHCP.
y Web Browser-based Monitoring
Using the Internet web browser to display the image in a local network environment.
y Automatic Local IP Setup
Even a network novice can install it with minimum operations.
y Alarm
If an alarm sensor is connected and it detects a motion, a message is sent to the registered
address via FTP/email (SMTP) or stored in the SD memory card, or an alarm will signal to the
alarm out terminal.
y Object Counting (only the MJPEG Live screen displays event rules and motion rectangle)
Applies object counting rule to the source image and acquires data to transfer to the configured
FTP server or displays in graph format.
overview
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
Camera
User Manual/
IP INSTALLER DVD
Quick Guide
Test Monitor Cable
Screw
Tapping Screw
Bracket Safety
M
 The Test Monitor Cable is connected to a portable displayer and used for testing the camera.
If you intend to use it for an actual monitoring camera, use the BNC cable instead.
10_ overview
AT A GLANCE
Appearance
● OVERVIEW
Item
Description
Dome Cover
Case cover used to protect the lens and the main unit.
b
Main Unit
Consists of: lens, switch board, PCB and screws.
c
Power Port
Used to plug in the power cable.
Video Output Port
Used to connect the Video In connector of the monitor, from which the video
signal of the camera outputs.
Network Port
Used to connect the PoE or LAN cable.
M
 Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied
ethanol.
English _11
overview
Inside
3
4
Item
Description
Network Port
Used to connect a PoE or LAN cable.
b
Alarm In / Out
terminals
Alarm in/out terminals can be configured as follows:
- ALARM IN : Terminal for Alarm Input.
- ALARM OUT : Terminal for Alarm Output.
- GND : Grounding terminal.
c
SD Memory Card
Compartment
Compartment for the SD memory card.
Reset Button
12_ overview
Resets the camera settings.
Press the button for about 3 seconds, and the system indicator turns off
and will restart.
J Resetting the camera requires reconfiguration of network settings (IP
address, subnet mask, gateway address etc.) using the IP Installer
software application.
Components
3
4
5
● OVERVIEW
Item
b
c
Description
Inner Cover
Cover for the main unit’s protection.
Side wing hooks
By lifting it while gently pressing the both ends, you can separate the inner cover.
ZOOM lever
You can adjust or fix the zoom ratio.
Focus lever
Turn the barrel left or right to adjust the focus, and turn the knob clockwise to
lock the focus.
Monitor Out
Using the test monitor cable, you can connect to a mobile display for camera
test.
English _13
installation &amp; connection
INSTALATION
Removing the dome cover
1. Hold down the bottom lock lever while removing
the cover with the other hand.
Removing the cover reveals the main unit and
inner cover.
2. To fix the camera position, hold down both
hooks of the inner cover while lifting it up.
14_ installation &amp; connection
INSERTING/REMOVING AN SD MEMORY CARD
Inserting an SD Memory Card
Push the SD memory card in the direction of the arrow shown in the diagram.
 Do not insert the SD memory card while it’s upside down by force. Otherwise, it may damage the
SD memory card.
Removing an SD Memory Card
Gently press down on the exposed end of the memory card as shown in the diagram to
eject the memory card from the slot.
J
 Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from the
slot when released.
 Before ejecting the SD memory card, release the checkbox &lt;SD Card Record&gt; in &lt;Alarm
image&gt; and press [Apply] button. (page 62)
English _15
● INSTALLATION &amp; CONNECTION
J
installation &amp; connection
MEMORY CARD INFORMATION (NOT INCLUDED)
What is a memory card?
The memory card is an external data storage device that has been developed to offer an
entirely new way to record and share video, audio, and text data using digital devices.
Selecting a memory card that’s suitable for you
Your camera supports SDHC memory cards.
You may, however, experience compatibility issues depending on the model and make of
the memory card.
Your camera supports SD memory cards.
Note that supported memory card capacity is up to 2GB.
For your camera, we recommend you use a memory card from the following manufacturers:
SDHC/SD Memory Card: Panasonic, Sandisk, Toshiba
Your camera supports 128MB to 16GB (SD Card : 2GB) of memory card capacity.
Playback performance can be affected depending on the speed of memory card, so use
the high-speed memory card.
To ensure proper recording of video data, we recommend you use a memory card that
supports at least read/write speed 10Mbps and Class 6.
Memory Card Use
SD and SDHC memory cards feature a switch that disables writing data on to the media.
Having this switch to the Lock position will prevent accidental deletion of data stored in the
memory card but at the same time will also prevent you from writing data on to the media.
❖ Memory Card Components
Contacts
Lock Switch
SDHC
16_ installation &amp; connection
CONNECTING WITH OTHER DEVICE
Monitor
Network
Power Supply
Connect the power adaptor to the power input port.
J
 Be careful not to reverse the polarity when you connect the power cable.
You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.
Connecting to the monitor
Connect the [V_OUT] port of the camera to the video input port of the monitor.
Network Connection
Connect the Network cable to the local network or to the Internet.
English _17
● INSTALLATION &amp; CONNECTION
Power
installation &amp; connection
Connecting to the I/O port box
Connect the Alarm I/O cable to the corresponding port of the inner port box.
ALARM IN
GND
ALARM OUT
y ALARM IN 1, 2 : Used to connect the alarm input signal.
y GND : Used for earth-grounding.
y ALARM OUT 1, 2 : Used to connect the alarm output signal.
Alarm I/O Wiring Diagram
ALARM IN 1
1
ALARM IN 2
2
GND
3
External Relay
ALARM OUT 1
4
External Relay
ALARM OUT 2
5
18_ installation &amp; connection
Adjusting the monitoring direction for the camera
Panning
Lens rotation
You can adjust the camera direction only when the camera is fixed on the ceiling.
Then, turning the camera to the left or right is referred to as &quot;Panning&quot;, while tilting the angle
is &quot;Tilting&quot;. For panning, the panning limit is 220˚ for the clockwise, and 120˚ for the counterclockwise, a total of 340˚ enabled; further rotation is stopped by the stopper.
Adjusting the tilt
Loosen the tilt adjustment screws and rotate the lens.
Adjust the lens and the floor at the angle of 90˚, and then tighten the tilt adjustment screws
to fix the lens.
 To use the &lt;Object counting&gt; function, adjust the camera lens vertically to face the floor.
Otherwise, the &lt;Object counting&gt; function may not work normally.
Adjusting the zoom and focus
Watch the camera’s real time video and rotate the “Zoom lever” to zoom in/out the subject
as you want.
Rotate the “Focus lever” until the image looks clear.
 For the position of the Zoom lever and Focus lever, refer to the “Components” (page 13).
M
 It is recommended to install the camera 2.5M~10M high above from the floor.
English _19
● INSTALLATION &amp; CONNECTION
Tilt Adjustment Screw
Tilting
camera setup
You can configure the camera settings using the Web Viewer.
M
 For accessing the Web Viewer, refer to &quot;Network Connection and Setup&quot;. (page 30)
HOW TO USE THE KEYBOARD CONTROLLER
Follow the steps below if you run the Web Viewer for setting the menus.
1. Launch the Web Viewer.
2. From the [Camera OSD] menu in the left
pane, click [Menu].
The &lt;MAIN MENU&gt; screen appears.
3. Click the Up/Down (▲▼) buttons to move to a
desired item.
4. Click the four direction (▲▼◄ ►) buttons to navigate through the menu items.
5. To change the value of a selected item, click the Left/Right (◄ ►) buttons.
].
6. Click [
Your changes will be applied.
: Exits the menu setup screen.
Before exiting the setup screen, select [SAVE] to save your settings, or [QUIT] to
cancel them.
: Saves your settings and returns to the previous screen.
: Use this icon if you want to save your settings after you specified the mask area and
privacy area, etc.
Once you saved your settings, the changes remain intact even if you select [QUIT] on
exit.
: Use this icon if you want to delete a mask, or privacy area, etc.
Once you deleted your settings, the deletions remain valid even if you select [QUIT] on
exit.
: This arrow appears next to a menu that contains sub items.
For the items with the &quot;*&quot; mark on the right, You can get help from &quot;Terminology&quot;. (page 72)
20_ camera setup
MAIN MENU
You can configure the camera settings to your preference.
** MAIN MENU **
PROFILE
CAMERA SET
PRIVACY ZONE
OTHER SET
SYSTEM INFO
PROFILE
You can select one from the pre-determined modes as appropriate to your specific camera installation
environment.
Your selection on each item in PROFILE will affect all other settings of the camera. For the
setting, refer to &quot;PROFILE&quot;. (page 71)
For selecting and saving each menu item, refer to &quot;How to use the keyboard controller&quot;. (page 20)
y STANDARD
◄ PROFILE ►
Automatically optimizes the camera settings to
*STANDARD
the normal environment.
ITS
y ITS
BACKLIGHT
DAY/NIGHT
This setting enables you to analyze the traffic
GAMING
situation and take the traffic information at a glance.
BANK
CUSTOM
y BACKLIGHT
This setting enables you to view a sharp background
and object even in a severe backlight scene.
y DAY/NIGHT
Automatically optimizes the camera settings to the day and night scene.
y GAMING
This automatically configures the settings so that you can work in a stable illumination
condition as indoors.
y BANK
Automatically optimizes the camera settings to the bank environment.
y CUSTOM
Your change to any of the PROFILE settings will switch the display to CUSTOM.
English _21
● CAMERA SETUP
y PROFILE
You can select a mode that is appropriate to the
camera installation environment.
y CAMERA SET
Configure the camera functions and settings.
y PRIVACY ZONE
You can configure the privacy settings.
y OTHER SET
You can configure more settings including
FACTORY DEFAULTS.
y SYSTEM INFO
Shows the camera version and type.
camera setup
CAMERA SETUP
You can configure the general settings of the camera module.
Use the four direction (▲▼◄ ►) buttons to select a desired item.
CAMERA ID
Provide the ID and position for a camera that displays on the screen.
For selecting and saving each menu item, refer to &quot;How to use the keyboard controller&quot;. (page 20)
1. Select &lt;CAMERA SET&gt; - &lt;CAMERA ID&gt;.
2. Use the four direction (▲▼◄ ►) buttons to
select a desired character.
In the lower input box of the screen, the
selected character will be entered.
 You can enter up to 54 characters including alphabets,
numbers and special characters.
CAMERA ID
ABCDEFGHIJKLMNOPQRSTUVWXYZO
BCDEFGHIJKLMNOPQRSTUVWXYZO
_
123456789 : ? + *()/
SP►► ◄◄
SP►►
◄◄ SP
LOCATION
-------------------------------------------------
3. When done, continue to select &lt;LOCATION&gt;
to specify the display position of the camera ID.
IRIS
You can set the iris to control the intensity of radiation incoming to the camera.
For selecting and saving each menu item, refer to &quot;How to use the keyboard controller&quot;. (page 20)
1. Select &lt;CAMERA SET&gt; - &lt;IRIS&gt;.
2. Use the left/right (◄ ►) buttons to select &lt;ALC&gt;.
y LEVEL : Select an overall brightness level.
y BACKLIGHT : Select either &lt;BLC&gt; or &lt;WDR&gt;.
- WDR : Specify the synthesis level in
the WEIGHT, and shutter speed in the
WDR LEVEL, or select &lt;OUTDOOR&gt; or
&lt;INDOOR&gt; in the WHITE BAL.
- BLC : Set the &lt;BLC&gt; area by specifying the
&lt;SIZE&gt; and &lt;POSITION&gt;.
M
ALC
LEVEL
BACKLIGHT
[ 00] ---- I ---OFF
 If the iris is set to &lt;ALC&gt;, fixing the iris is your priority when you adjust AE and the shutter speed.
22_ camera setup
MOTION
◄
CAMERA SET
CAMERA ID
IRIS
MOTION
DNR
SHUTTER
SENS-UP
FLICKERLESS
XDR
DIS
►
ON
ALC
(F.FAST)
(F.FAST)----MID
OFF
AUTO X4
OFF
MID
OFF
DNR
Reduces the noise on the screen.
This is useful, especially for a noisy screen.
Set it to &lt;USER&gt;, you can specify the level.
SHUTTER
The SHUTTER menu is used to set the fixed fast
electronic shutter or auto fast electronic shutter.
DAY/NIGHT
WHITE BAL
DIGITAL ZOOM
DETAIL
AGC COLOR SUP
REVERSE
POSI/NEGA
PIP
AUTO
[2]
OFF
MID
OFF
+
OFF
SENS-UP
If the brightness of the video signal is too low, the
Slow Shutter function will be activated.
Slow Shutter can collect the individual max frame rate to adjust the setting.
FLICKERLESS
If set to &lt;ON&gt;, the shutter speed will be fixed to 1/100 second. This will prevent possible
screen distortion due to a mismatch between the vertical sync frequency and the blinking
frequency of the lighting.
 If SHUTTER is set to AUTO, FIX, EXT mode / SENSE UP to FIX / AGC to FIX, the &lt;DIS&gt; menu will be
disabled.
XDR
This will correct a brightness difference between different scenes for the optimal visibility.
The higher the value is, the higher the correction level is.
DIS
Automatically compensates for the flicker on the screen.
If set to &lt;ON&gt;, the image will be enlarged with digital zoom as much area as
compensated.
 If you set DIS to ON, the compensation area will be enlarged as set in the digital zoom factor.
If you set the digital zoom factor to greater than the enlarged zoom factor for the compensation, the DIS
function will be deactivated.
English _23
● CAMERA SETUP
You can specify a level of AGC for controlling the
camera motion.
Select F.FAST if you want to monitor a very fast
moving object in a low contrast scene, and S.SLOW
if monitoring a very slow moving, inanimate object in
the same condition.
As long as DAY/NIGHT is set to AUTO, the
&lt;MOTION&gt; menu is not available.
camera setup
DAY/NIGHT
You can specify a recording mode according to the scene.
For selecting and saving each menu item, refer to &quot;How to use the keyboard controller&quot;. (page 20)
1. Select &lt;CAMERA SET&gt; - &lt;DAY/NIGHT&gt;.
2. Select a screen transition mode according to
the illumination, and set options as appropriate.
y DAY : Fixed to DAY mode, regardless of the
scene.
y NIGHT : Fixed to NIGHT mode, regardless
of the scene.
If BURST is set to &lt;ON&gt;, the burst signal will
output.
y AUTO : According to the luminance, this will
switch DAY to NIGHT mode, or vice versa.
y DAYNIGHT / NIGHTDAY : If set to
&lt;AUTO&gt;, you can specify the brightness
level triggering the mode switch between
DAY and NIGHT as well as the interval.
y MASK AREA : If there exists a bright spot
light source in a night scene, you can specify
the size and position as needed.
Any excessively bright area in a night scene
will be masked.
24_ camera setup
AUTO
BURST
DAY
DAY
NIGHT
BRIGHTNESS
DWELL TIME
NIGHT
NIGHT
DAY
BRIGHTNESS
DWELL TIME
MASK AREA
MASK AREA
&lt;SIZE&gt;
&lt;LOCATION&gt;
OFF
MID
2S
1
MID
5S
2
WHITE BAL
If you need to adjust the screen brightness, use the WHITE BALANCE function.
For selecting and saving each menu item, refer to &quot;How to use the keyboard controller&quot;. (page 20)
1. Select &lt;CAMERA SET&gt; - &lt;WHITE BAL&gt;.
WHITE BAL
DAY/NIGHT
MODE
RED
BLUE
DAY
ATW2
[ 00]
00] ---- I ---[ 00
00]] ---- I ----
3. According to the specified recording mode,
WHITE BAL
select a WHITE BAL mode with necessary
options.
DAY/NIGHT
NIGHT
BRIGHTNESS
MID
y BRIGHTNESS : Specify a brightness level
MODE
AWC
[ 00
RED
00]] ---- I ---triggering the switch from DAY to NIGHT
[ 00
BLUE
00]] ---- I ---mode.
[[0040
R-GAIN
0040]]
[[0133
B-GAIN
0133]]
y MODE : According to the selected mode,
you can adjust the RED and BLUE color
level.
- RED : Adjust the strength of the red color.
- BLUE : Adjust the strength of the blue color.
- R-GAIN/B-GAIN : Specify the current color temperature manually.
 You can set the R-GAIN, and B-GAIN value only in AWC mode.
DIGITAL ZOOM
You can set the digital zoom factor and position.
When the zoom factor and position are defined, the digital zoom function will operate.
 If you set the digital zoom to a larger factor than the actual enlargement for compensation, the DIS
function will be disabled.
DETAIL
You can adjust the vertical and horizontal sharpness, respectively.
English _25
● CAMERA SETUP
2. Select a mode where you set the balance.
y DAY : You can set the RED, and BLUE value
in DAY mode.
y NIGHT : You can adjust the &lt;WHITE BAL&gt;
according to the ambient luminance.
camera setup
AGC COLOR SUP
This will adjust the color scheme according to the AGC value.
REVERSE
This will reverse the signal left to right, top to bottom, or a combination of the preceding.
POSI/NEGA
This will display the video brightness signal either normally or reversely.
PIP
You can view a main image with a sub image on the same screen.
 If more than one privacy zone is set and the PRIVACY SET is set to ON, the PIP function will be
deactivated.
26_ camera setup
PRIVACY ZONE
You can set up to 12 privacy zones that will be hided for privacy of the subject when recording.
For selecting and saving each menu item, refer to &quot;How to use the keyboard controller&quot;. (page 20)
ZONE SETUP
1. Select &lt;MAIN MENU&gt; - &lt;PRIVACY ZONE&gt;.
3. Select the &lt;PIXEL LEVEL&gt;.
Specify the pixel unit level for the POSITION
setting.
4. Select &lt;POINT&gt;.
You will see dots on the screen.
◄
1
7
PRIVACY ZONE
2
8
3
9
4
10
5
11
PRIVACY SET
STYLE
►
6
12
ON
MOSAIC1
PRIVACY ZONE SET 1
PIXEL LEVEL
&lt;POINT&gt;
&lt;POSITION&gt;
[4]
5. Use the four direction (▲▼◄ ►) buttons to
specify the position for each of the four dots.
6. Select &lt;POSITION&gt; and use the four direction
(▲▼◄ ►) buttons to specify the position for
each of the four dots.
7. Save the changes and move to the previous screen and select the &lt;STYLE&gt;.
Select &lt;COLOR&gt; and pick a desired color.
M
 Setting one or more privacy zone and enabling privacy function will disable the PIP function.
English _27
● CAMERA SETUP
2. Use the four direction (▲▼◄ ►) buttons to
select a desired number.
The Zone setup screen appears.
camera setup
OTHERS
You can reset the camera, or select the OSD font color to your preference.
For selecting and saving each menu item, refer to &quot;How to use the keyboard controller&quot;. (page 20)
LANGUAGE
You can slect a preferred language for the screen
display.
Select your language by using the left and right keys.
◄
OTHER SET
►
LANGUAGE
ENGLISH
FACTORY DEFAULTS
OSD COLOR
BW
FACTORY DEFAULT
1. Select &lt;MAIN MENU&gt; - &lt;OTHER SET&gt;
- &lt;FACTORY DEFAULTS&gt;.
The FACTORY DEFAULTS setup screen
appears.
2. Select &lt;OK&gt;.
All the settings will be restored to the factory
default.
However, the language setting will not be
restored.
OSD COLOR
You can set the font color of the user interface.
28_ camera setup
FACTORY DEFAULTS
OK
CANCEL
SYSTEM INFO
You can check the system information.
For selecting and saving each menu item, refer to &quot;How to use the keyboard controller&quot;. (page 20)
1. Select &lt;MAIN MENU&gt; - &lt;SYSTEM INFO&gt;.
2. The current system information is displayed.
 The camera type may different, depend on the video
SYSTEM INFO
►
3_IPV_N
v2.00_101012
signal.
English _29
● CAMERA SETUP
M
◄
TYPE
CAMERA VER.
network connection and setup
You can set up the network settings according to your network configurations.
M
 Before installing or while using this program, visit the Samsung website www.samsungsecurity.com
and download and upgrade with the latest S/W version available.
CONNECTING THE CAMERA TO AN IP ROUTER WITH THE
XDSL/CABLE MODEM
This is for a small network environment such as homes, SOHO and ordinary shops.
SND-3080CF
INTERNET
SND-3080CF
IP Router
xDSL or
Cable Modem
xDSL or
Cable Modem
External Remote PC
Local PC
DDNS Server
(Data Center, KOREA)
Configuring the network settings of the local PC connected to an
IP router
Configuring the network settings of the local PC connected to an IP router, follow the
instructions below.
y Select : &lt;Network Neighborhood&gt; &lt;Properties&gt; &lt;Local Area Connection&gt;
&lt;Properties&gt; &lt;General&gt; &lt;Internet Protocol (TCP/IP)&gt; &lt;Properties&gt;
&lt;Obtain an IP address automatically&gt; or &lt;Use the following IP address&gt;.
y Follow the instructions below if you select &lt;Use the following IP address&gt;:
ex1) If the address (LAN IP) of the IP router is 192.168.1.1
IP address: 192.168.1.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
ex2) If the address (LAN IP) of the IP router is 192.168.0.1
IP address: 192.168.0.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.1
30_ network connection and setup
ex3) If the address (LAN IP) of the IP router is 192.168.xxx.1
IP address: 192.168.xxx.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.xxx.1
M
 For the address of the IP router, refer to the product’s documentation.
Checking if the IP router is connected to the xDSL/Cable modem properly
y If it is properly connected, &lt;IP Address&gt;, &lt;Subnet Mask&gt; and &lt;Gateway&gt;
provided by your ISP are displayed. Please remember these values because they
are required so that an external remote computer of the IP router connects to the
camera. However, note that certain ISPs change the settings of &lt;IP Address&gt;,
&lt;Subnet Mask&gt; and &lt;Gateway&gt; on a regular basis
y If the IP router is not properly connected, press the [Connect] button to try to reconnect or check if the settings of the IP router are correct.
CONNECTING THE CAMERA TO AN IP ROUTER WITH
LOCAL AREA NETWORKING
This is for a large network environment such as corporate office, building, public office and factory.
SND-3080CF
INTERNET
SND-3080CF
External Remote PC
IP Router
Firewall
Local PC
Local PC
DDNS Server
(Data Center, KOREA)
Configuring the network settings of the local PC connected to an
IP router
Configuring the network settings of the local PC connected to an IP router, follow the
instructions below.
y Select : &lt;Network Neighborhood&gt; &lt;Properties&gt; &lt;Local Area Connection&gt;
&lt;Properties&gt; &lt;General&gt; &lt;Internet Protocol (TCP/IP)&gt; &lt;Properties&gt;
&lt;Obtain an IP address automatically&gt; or &lt;Use the following IP address&gt;.
English _31
● NETWORK CONNECTION AND SETUP
Select &lt;Status&gt; from the Settings menu of the IP Router
network connection and setup
y Follow the instructions below if you select &lt;Use the following IP address&gt;:
ex1) If the address (LAN IP) of the IP router is 192.168.1.1
IP address: 192.168.1.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
ex2) If the address (LAN IP) of the IP router is 192.168.0.1
IP address: 192.168.0.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.1
ex3) If the address (LAN IP) of the IP router is 192.168.xxx.1
IP address: 192.168.xxx.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.xxx.1
M
 For the address of the IP router, refer to the product’s documentation.
CONNECTING THE CAMERA DIRECTLY TO A DHCPBASED XDSL/CABLE MODEM
INTERNET
SND-3080CF
xDSL or
Cable Modem
External Remote PC
DDNS Server
(Data Center, KOREA)
Setting the IP Router
This is enabled for a modem using DHCP.
1. Set the Static or Dynamic IP address. (pages 35~38)
2. Launch an Internet browser on the local PC connected to the IP Router.
3. Enter the IP Router’s address in the address bar of the browser.
ex) http://192.168.1.1, http://192.168.0.1 or http://192.168.xxx.1
 For the DDNS URL address, refer to &quot;To check the DDNS address&quot;. (page 42)
32_ network connection and setup
4. When the IP Router is connected, the login window appears and prompts you to
enter the password.
 For the login IP and the password, refer to the IP router’s documentation.
5. When done, you will see the setup window of the IP router. In the setup menu,
select “Automatic Configuration-DHCP” for Internet Connection Type.
 For the menu location of Internet Connection Type or DHCP selection, refer to the IP router’s
documentation.
CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA
NETWORKING
Connecting to the camera from a local PC in the LAN
1. Launch an Internet browser on the local PC.
2. Enter the IP address of the camera in the address bar of the browser.
SND-3080CF
INTERNET
SND-3080CF
External Remote PC
Firewall
Local PC
DDNS Server
(Data Center, KOREA)
M
 A remote PC in an external Internet out of the LAN network may not be able to connect to the
camera installed in the intranet if the port-forwarding is not properly set or a firewall is set.
In this case, to resolve the problem, contact your network administrator.
English _33
● NETWORK CONNECTION AND SETUP
6. When done, click the [Save] or [Apply] button to save the settings.
network connection and setup
BUTTONS USED IN IP INSTALLER
Item
Description
Device Name
Model name of the connected camera.
Click the column to sort the list by model name.
However, search will be stopped if clicked during the search.
b
Mode
Displays either &lt;Static&gt; or &lt;Dynamic&gt; for the current network connection
status.
c
MAC(Ethernet)
Address
Ethernet address for the connected camera.
Click the column to sort the list by Ethernet address.
However, search will be stopped if clicked during the search.
IP Address
IP address.
Click the column to sort the list by IP address.
However, search will be stopped if clicked during the search.
The factory default is “192.168.1.200”.
Protocol
Network setting for the camera.
The factory default is &quot;IPv4&quot;.
Cameras with the IPv6 setting will be displayed &quot;IPv6&quot;.
UPnP Status
This function is not currently implemented.
34_ network connection and setup
Item
m
URL
DDNS URL address enabling access from the external Internet.
However, this will be replaced with the &lt;IP Address&gt; of the camera if
DDNS registration has failed.
IPv4
Scans for cameras with the IPv4 setting.
IPv6
Scans for cameras with the IPv6 setting.
Search
Scans for cameras that are currently connected to the network.
However, this button will be grayed out if neither IPv4 nor IPv6 is checked.
Auto Set
&lt;IP Installer&gt; will automatically configure the network settings for you.
Manual Set
You should configure the network settings manually.
Exit
Exits the IP Installer program.
STATIC IP SETUP
Manual Network Setup
Run &lt;IP Installer.exe&gt; to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
M
 For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not
support this function.
1. Select a camera in the search list.
Find the MAC (Ethernet) address
labeled on the rear of the camera.
Both the [Auto Set] and [Manual Set]
buttons will be activated.
2. Click [Manual Set].
The Manual Setting dialog appears.
The default values of &lt;IP Address&gt;,
&lt;Subnet Mask&gt;, &lt;Gateway&gt;, and &lt;HTTP Port&gt; of the camera will be displayed.
The default &lt;Password&gt; is &quot;4321&quot;.
3. In the &lt;Address&gt; pane, provide the
necessary information.
y MAC (Ethernet) Address : The MAC
(Ethernet) address of the applicable
camera will be set automatically so
you don't need to input it manually.
English _35
● NETWORK CONNECTION AND SETUP
Description
network connection and setup
If using an IP router :
y IP Address : Enter an address falling in
the IP range provided by the IP router.
ex) 192.168.1.2~254,
192.168.0.2~254,
192.168.XXX.2~254
y Subnet Mask : The &lt;Subnet Mask&gt; of
the IP router will be the &lt;Subnet Mask&gt;
of the camera.
y Gateway : The &lt;Local IP Address&gt; of
the IP router will be the &lt;Gateway&gt; of
the camera.
If not using an IP router :
For setting &lt;IP Address&gt;, &lt;Subnet Mask&gt;, and &lt;Gateway&gt;, contact your network
administrator.
M
 The values of Device, TCP, UDP, Upload, and Multicast ports can not be changed manually, and
will be adjusted according to the HTTP port value.
4. In the &lt;Port&gt; pane, provide necessary
information.
y HTTP Port : Used to access the
camera using the Internet browser,
defaulted to 80. Use the spin button
to change the HTTP Port value. The
start value of the port is 80, and
increases or decreases by 6 like
10000, 10006, 10012.
y VNP Port : Used to control the video signal transfer, defaulted to 60001(TCP).
y TCP Port : Video signal transfer port using TCP protocols, defaulted to
60002(TCP).
y UDP Port : Video signal transfer port using the UDP Unicast method, defaulted to
60003(UDP).
y Upload Port : Used to upgrade the software firmware, defaulted to 60004(TCP).
y Multicast Port : Video signal transfer port using the UDP Multicast method,
defaulted to 60005(UDP).
5. Enter the password.
This is the login password for the &quot;admin&quot; user who accesses the camera.
The default password is &quot;4321&quot;.
36_ network connection and setup
6. Click [OK].
Manual network setup will be completed.
7. When the manual setup including &lt;IP&gt; is completed, the camera will restart.
If the IP router has more than one camera connected
Configure the IP related settings and the Port related settings distinctly with each other.
Category
IP Address
Subnet Mask
Gateway
HTTP Port
VNP Port
TCP Port
Port related settings
UDP Port
Upload Port
Multicast Port
M
Camera #2
192.168.1.200
255.255.255.0
192.168.1.1
192.168.1.201
255.255.255.0
192.168.1.1
80
60001
60002
60003
60004
60005
10000
10001
10002
10003
10004
10005
 If the &lt;HTTP Port&gt; is set other than 80, you must provide the &lt;Port&gt; number in the address
bar of the Internet browser before you can access the camera.
ex) http://IP address : HTTP Port
http://192.168.1.201:10000
Auto Network Setup
Run &lt;IP Installer.exe&gt; to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
M
 For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not
support this function.
1. Select a camera in the search list.
Find the MAC (Ethernet) address
labeled on the rear of the camera.
Both the [Auto Set] and [Manual Set]
buttons will be activated.
2. Click [Auto Set].
The Auto Setting dialog appears.
The &lt;IP Address&gt;, &lt;Subnet Mask&gt;,
and &lt;Gateway&gt; will be set automatically.
English _37
● NETWORK CONNECTION AND SETUP
IP related settings
Camera #1
network connection and setup
3. Enter the password.
This is the login password for the
&quot;admin&quot; user who accesses the
camera.
The default password is &quot;4321&quot;.
4. Click [OK].
Auto network setup will be completed.
5. The camera will automatically complete
the network setting and restart.
DYNAMIC IP SETUP
Dynamic IP Environment Setup
y Example of the dynamic IP environment
- If an IP router, with cameras connected, is assigned an IP address by the DHCP
server
- If connecting the camera directly to the xDSL or cable modem using the DHCP
protocols
- If IPs are assigned by the internal DHCP server via the LAN
Checking the dynamic IP
1. From a local PC, run &lt;IP Installer&gt;
to display a list of cameras that are
assigned &lt;Dynamic IP&gt;.
2. Select a camera in the list, and click
[Manual Set] to check the &lt;Dynamic
IP&gt; of the camera.
If you uncheck &lt;DHCP&gt;, you can
change &lt;IP&gt; or &lt;Port&gt; to &lt;STATIC&gt;.
38_ network connection and setup
PORT RANGE FORWARD (PORT MAPPING) SETUP
If you have installed an IP router with a camera connected, you must set the port range
forwarding on the IP router so that a remote PC can access the camera in it.
Manual Port Range Forwarding
● NETWORK CONNECTION AND SETUP
1. From the Setup menu of the IP router,
select &lt;Applications &amp; Gaming&gt; &lt;Port Range Forward&gt;.
For setting the port range forward for
a third-party IP router, refer to the user
guide of that IP router.
2. Select &lt;TCP&gt; and &lt;UDP Port&gt; for
each connected camera to the IP
router.
Each port number for the IP router
should match that specified in &lt;Basic&gt;
- &lt;IP&gt; from the camera's Setup menu.
3. When done, click [Save Settings].
Your settings will be saved.
English _39
network connection and setup
CONNECTING TO THE CAMERA FROM A SHARED LOCAL
PC
1. Launch &lt;IP Installer&gt;.
It will scan for connected cameras and
display a list of them.
2. Double-click a camera to access.
The Internet browser starts and
connects to the camera.
M
 You can also access the camera in such
way you type the IP address of the found camera in the address bar of the Internet browser.
CONNECTING TO THE CAMERA FROM A REMOTE PC VIA
THE INTERNET
As a remote PC can not directly access &lt;IP Installer&gt;, you should access the camera in the IP
router network using DDNS URL of the camera.
1. Before you can access a camera in the IP router network, you should have set the
port range forward for the IP router.
2. From the remote PC, launch the Internet browser and type the DDNS URL address
of the camera, or the IP address of the IP router in the address bar.
ex) http://mfffe42.websamsung.net
 For the DDNS URL address, refer to &quot;To check the DDNS address&quot;. (page 42)
40_ network connection and setup
web viewer
CONNECTING TO THE CAMERA
Normally, you would
● WEB VIEWER
1. Launch the Internet browser.
2. Type the IP address of the camera in
the address bar.
ex) • IP address (IPv4) : 192.168.1.200
http://192.168.1.200
- the Login dialog should appear.
• IP address (IPv6) : 2001:230:abcd:
ffff:0000:0000:ffff:1111
http://[2001:230:abcd:ffff:0000
:0000:ffff:1111]
If the HTTP port is other than 80
1. Launch the Internet browser.
2. Type the IP address and HTTP port number of the camera in the address bar.
ex) IP address : 192.168.1.200:Port number(10000) http://192.168.1.200:10000
- the Login dialog should appear.
Using URL
1. Launch the Internet browser.
2. Type the DDNS URL of the camera in the address bar.
ex) URL address : http://mfffe42.websamsung.net
- the Login dialog should appear.
Connecting via URL (If the HTTP port is other than 80)
1. Launch the Internet browser.
2. Type the DDNS URL and HTTP port number of the camera in the address bar.
ex) URL address : http://mfffe42.websamsung.net:Port number(10000)
http://mfffe42.websamsung.net:10000
- the Login dialog should appear.
English _41
web viewer
To check the DDNS address
The DDNS address consists of: &lt;one of the lower-case letters: c, m, p&gt; + &lt;the last 6 digits
of the MAC (Ethernet) address&gt; + &lt;websamsung.net&gt;
The small letter will be &lt;c&gt; if the first 6 digits of the MAC (Ethernet) address is &lt;00:00:f0&gt;,
or &lt;m&gt; if they are &lt;00:16:6c&gt;, or &lt;p&gt; for &lt;00:68:36&gt;.
ex) - If the MAC (Ethernet) address is 00:00:f0:ff:fe:42: c + fffe42 + websamsung.net =
cfffe42.websamsung.net
- If the MAC (Ethernet) address is 00:16:6c:ff:fe:42: m + fffe42 +websamsung.net =
mfffe42.websamsung.net
- If the MAC (Ethernet) address is 00:68:36:ff:fe:42: p + fffe42 +websamsung.net =
pfffe42.websamsung.net
J
 The above mentioned addresses are simply examples; do not use any of these for connecting
purposes.
LOGIN
The default user ID is “admin”, and the default password is “4321”.
1. Enter “admin” in the &lt;User Name&gt;
input box.
2. Enter “4321” in the &lt;Password&gt; input
box.
If the password is changed, enter the
changed password instead.
3. Click [OK].
If you have logged in successfully, you
will the Live Viewer screen.
M
 For security purposes, ensure that you change the password in &lt;Basic&gt; - &lt;User&gt;.
The administrator ID, “admin”, is fixed and can not be changed.
 If you check the “Save this password in your password list” option when your input is done, you
will be logged in automatically without being prompted to enter the login information from next time on.
J
 For this, your computer has installed DirectX 8.1 or later.
You can get a free download of the latest DirectX from http://www.microsoft.com/download.
If you are using Internet Explorer 7.0 or 8.0 as the default web browser, you can view the best
quality image with a screen ratio of 100%. Reducing the ratio may cut the image on the borders.
42_ web viewer
INSTALLING ACTIVEX
If connecting to a camera for the first time, you will see the installation message. Then, install the
required ActiveX to access the camera and control the video from it in real time.
For Windows XP Service Pack 2 users
● WEB VIEWER
1. Click the installation message that pops
up when you first access the camera.
2. Click &lt;Install ActiveX Control...&gt;.
3. The security warning popup appears,
click [Install].
4. When the required ActiveX is installed
properly after your access to the
camera, the Live screen should appear.
J
 For normal installation, set the Block
Popup setting as follows:
Internet Explorer ➝ Tools ➝ Block
Popup ➝ Always allow popups from
the current site(A)
English _43
web viewer
USING THE LIVE SCREEN
Item
b
c
Description
SD search
Moves to the screen for searching event images from the SD card.
Setup
Move to the Setup screen.
About
You can check the firmware version, serial number and manufacturer information.
Reset Alarm
Resets the Alarm icon. (the Alarm and Motion icons disappear.)
Capture
Saves the snapshot as an image file in the .jpeg or .bmp format.
Print
Prints out the current image.
Record
Saves the snapshot as a video file in the .avi format.
Full Screen
Displays the Live screen in full screen.
Video format
You can set the video format (MJPEG, H.264/MPEG4) for vidoe files.
The context menu will differ, depending on the codec specified in &lt;Select H.264 &amp;
MPEG4 Video&gt; of the active viewer.
Alarm output
On : Activates the specified Alarm Out port.
Off : Deactivates the specified Alarm Out port.
Pulse : Activates the Alarm Out port as much time as specified before deactivating it.
44_ web viewer
Item
Description
Used to retrieve and customize the Camera Setup menu.
Camera OSD
Object counting
Displays the event occurrence count summed up by the rule designated at
&lt;Set rules&gt; in &lt;Object counting&gt;.
m
Viewer Screen
Displays the Live video on the screen.
For selecting and saving each menu item, refer to “How to use the keyboard controller”.
(page 20)
● WEB VIEWER
BACKUP
You can capture, print out, and save the snapshot in the specified path.
To capture the snapshot
1. Click [ ] on the scene to capture.
The Capture dialog should appear.
2. Click [OK].
The screenshot will be saved in the
specified path.
y Default file path
- Windows XP : C:\Program Files\
Samsung\SND-3080C\SnapShot\Live
If you want to change the path, click [Set path ( )] and specify a path.
- Windows Vista, Windows 7 : C:\users\[UserID]\Documents\Samsung\
SND-3080C\SnapShot\Live
On the Windows Vista, Windows 7 system, the path to save is fixed.
y The screenshot file will be named automatically in the format of &lt;IP address_
Port number_YYYYMMDD_hhmmss_index&gt;.
ex) 192.168.1.200_60001_20101012_204029_00
To print out the screenshot
1. Click [ ] on the scene to print out.
The Print setup dialog appears.
2. Specify the name of the printer
connected, and click [OK].
English _45
web viewer
To record a video
1. Click [
] on the scene to record.
2. You will see the Save AVI dialog;
provide the necessary information.
y Save path : You can change the
default saving path.
y File name : You can change the
default file name.
y HDD minimum free size : If the free
space on the HDD is less than the
recorded space, recording will be forcibly ended.
3. Click [OK].
Recording will start with the display of
&lt;REC&gt; on the viewer screen.
The video file will be saved into the
specified path.
4. If you want to quit recording, click [ ]
again.
y Default file path
- Windows XP : C:\Program Files\
Samsung\SND-3080C\VideoClip\
Live
If you want to change the path,
click [Set path ( )] and specify a path.
- Windows Vista, Windows 7 : C:\users\[UserID]\Documents\Samsung\
SND-3080C\VideoClip\Live
On the Windows Vista, Windows 7 system, the path to save is fixed.
y The screenshot file will be named automatically in the format of &lt;IP address_
Port number_YYYYMMDD_hhmmss_index&gt;.
ex) 192.168.1.200_60001_20101012_204059_00
y If you want to play an .avi file, you must have installed the corresponding DivX
codec on your system.
You can get a free download of the DivX from http://sourceforge.net/projects/
ffdshow/.
y A specific codec to MPEG4 is required before you can play videos in the MPEG4 format.
You can download the codec for MPEG4 videos from www.samsungsecurity.com.
46_ web viewer
CHECKING THE OBJECT COUNTING
1. Go to &lt;Setup&gt; - &lt;Object counting&gt;
and select the &lt;Enable&gt; to set the
event rule.
 For more information, refer to “To set the
object counting function” (page 64).
3. Check the Count Results for the Line
crossing or the Area Occupancy which
is displayed in the &lt;Object counting&gt;.
y Line In : If you draw a straight line from top(left) to bottom(right) to set the Line
Crossing, the number of objects that cross the straight line from left(bottom) to
right(top) is displayed. Or if you draw straight line from bottom(right) to top(left)
to set the Line Crossing, the number of objects that cross the straight line from
right(top) to left(bottom) is displayed.
y Line Out : If you draw a straight line from top(left) to bottom(right) to set the Line
Crossing, the number of objects that cross the straight line from right(top) to
left(bottom) is displayed. Or if you draw straight line from bottom(right) to top(left)
to set the Line Crossing, the number of objects that cross the straight line from
left(bottom) to right(top) is displayed.
y Area : Displays the number of objects appeared in the polygon which is drawn in
the Area Occupancy configuration screen.
M
 The &lt;Line In&gt; and &lt;Line Out&gt; display the data accumulated before resetting.
They are reset to 0 when the volume of the accumulated data reaches 10,000,000.
 The &lt;Area Counting&gt; displays the average data during the &lt;Area Counting Interval&gt;.
To reset the Object Counting, click the &lt;Reset&gt; button.
The number displayed in &lt;Line In&gt; and &lt;Line Out&gt; is reset to 0.
The number displayed in the &lt;Area&gt; is updated every object counting interval selected in the
Object Counting Configuration.
English _47
● WEB VIEWER
2. Select the &lt;MJPEG&gt; for &lt;Video
format&gt; and press the [Refresh]
button in the browser.
web viewer
USING THE SD SEARCH VIEWER SCREEN
1. Click &lt;SD search&gt; tab in the Live screen.
2. The SD Search Screen appears.
Name
b
c
Function and description
Thumbnail Size
The thumbnail images are displayed based on the selected size.
Date
You can select the desired date to search for events generated.
Schedule
You can select the desired time to search the schedule events.
Alarm input
You can select the desired time to search the alarm events.
48_ web viewer
setup screen
ACCESSING THE SETUP SCREEN
You can configure the default setting, system, overlay, event and network related settings, and
change them as necessary.
● SETUP SCREEN
1. In the Live screen, click the &lt;Setup&gt; tab.
2. The Setup screen appears.
English _49
setup screen
DEFAULT SETUP
To configure the video settings
You can set the video resolution and quality, and select the codec required.
1. Select &lt;Basic&gt; - &lt;Video&gt;.
The Video setup screen appears.
y Brightness : Adjust the screen
brightness from 1 to 100.
y Contrast : Adjust the contrast from
1 to 100.
y Resolution : Set the video size of the
MPEG4, H.264, and MPEG files.
- NTSC : 4CIF(704x480),
VGA(640X480), CIF(352X240)
- PAL : 4CIF(704x576),
VGA(640X480), CIF(352X288)
y Quality : Adjust the picture quality
from 1 to 10.
y Frame rate :
- NTSC : Select one from 30 fps, 15
fps, 8 fps, 3 fps, and 1 fps.
- PAL : Select one from 25 fps,
13fps, 6fps, 3fps and 1fps.
y Bitrate control* : Select CBR
(Constant Bit Rate) or VBR (Variable
Bit Rate) for the compression
method.
 If selecting VBR, you can not set the target bit rate.
y
y
y
y
y
y
Target bitrate : Transfers video signal at a specified bit rate.
Compression : Adjust the compression rate from 5 through 100 by 5.
Encode priority : Set the video transfer method to Frame rate or Quality.
GOP* size : Select a GOP size between 5 and 15.
Deblock : This will soften the edges between macro blocks.
De-interlace : You can set the grid noise reduction function.
 This can be set only if the resolution of MPEG4 video is 4CIF.
50_ setup screen
y Profile : Select Baseline or Main for the H.264 profiling method.
y Entropy coding* : Reduces the compression loss due to encoding.
y Motion estimation : Estimates the movement of pixels by determining the motion
vector.
J
 If you set the profile to Baseline, the entropy coding is available only for CAVLC*; if you set it to
MAIN, the entropy coding is available for both CAVLC* and CABAC*.
 If you set WDR to &lt;OFF&gt;, or the resolution of MPEG4 video is other than 4CIF, De-Interlace of
● SETUP SCREEN
MPEG4 codec will not be available.
2. When done, click [Apply].
Your settings will be saved.
To configure the IP settings
1. Select &lt;Basic&gt; - &lt;IP&gt;.
The IP setup window appears.
y IP configuration : Set the IP and port
settings for the camera.
- IP type : Select one from &lt;Static
IP&gt;, &lt;Dynamic IP&gt;, and &lt;PPPoE
IP&gt;.
 If you select &lt;PPPoE IP&gt;, you can
provide the optional ADSL IP and
password. However, the multicast items
(multicast address, port, TTL) for VNP
and RTP will disappear.
- MAC address : Displays the
Ethernet MAC address.
This is used for creating a DDNS
address.
- IP address : Displays the current IP
address.
- Subnet mask : Displays the
&lt;Subnet mask&gt; for the set IP.
- Gateway : Displays the &lt;Gateway&gt; for the set IP.
- DNS server : Displays the DNS(Domain Name Service) server address.
- HTTP webserver port : HTTP port used to access the camera via the web
browser. The default is 80(TCP).
- Upload port (TCP) : Used to upgrade the software firmware, defaulted to 60004(TCP).
y IPv6 configuration : Obtains the IPv6 address to access the IPv6 network.
English _51
setup screen
y VNP configuration : Set a port used to transfer video signals with the Samsung
protocols.
- Device port (TCP) : Used to control the video signal transfer, defaulted to 60001(TCP).
- TCP streaming port : Video signal transfer port using TCP protocols, defaulted
to 60002(TCP).
- UDP streaming port : UDP Port used to transfer video signal with the UDP
Unicast protocols. The default is 60003(UDP).
- Multicast address : IP address used to transfer video signal with the UDP
Multicast protocols.
The default is 225.128.1.128, and if you want to change the address, specify it
ranging from 224.0.0.0 to 239.255.255.255.
- Multicast port : UDP Port used to transfer video signal with the UDP Multicast
protocols. The default is 60005(UDP).
- TTL* : Set the TTL for the VNP packet.
The default is 63, and if you want to change the address, specify it ranging from
0 to 255.
y RTP configuration : You can set the RTP protocol.
- RTSP port : You can set the RTSP port.
- Streaming port : Used to transfer video signal with the RTP protocols.
The default range is between 61000 and 61999.
- Multicast address : IP address used to transfer video signal with the RTP
protocols.
- Multicast port : Used to transfer video signal with the RTP-protocol multicasting.
- TTL* : You can set the TTL for the RTP packet.
2. When done, click [Apply].
Your settings are saved and the system restarts.
The currently opened web browser will be closed.
M
 If the IP router has more than one camera connected, you should configure IP and port settings
differently with each other.
52_ setup screen
To set the user account
2. When done, click [Apply].
Your settings will be saved.
The currently opened web browser will be closed.
User Registration
1. From the User setup window, click
[Insert].
The Register User window appears.
2. Provide the &lt;User ID&gt;, &lt;Password&gt;,
and &lt;Confirm password&gt;,
respectively. You can enter up to 9
alphanumeric or special characters
(some excluded) for the user ID and
password, respectively.
3. Select a user level.
Select either &lt;Operator&gt; or &lt;User&gt; for a new user's permission.
4. Click [Apply].
The user registration is completed.
J
 An existing user ID can not be added duplicate.
 Neither admin ID nor guest ID can be registered.
English _53
● SETUP SCREEN
1. Click &lt;Basic&gt; - &lt;User&gt;.
The User setup window appears.
y Login authentication : You can set to
authenticate the login by the user.
- If you select &lt;Enable&gt;, the user
should have gone through the
login authentication; if selecting
&lt;Disable&gt;, every user can access
the system without the login authentication, having the ordinary user permissions.
- When done, click [Apply].
y User login ID/password list : Displays a list of accessible users ID, passwords, and
ratings.
- You can add up to 10 users.
- The admin ID is “admin”.
- The password for the admin ID can be changed, but not added or deleted.
setup screen
To edit a registered user account
1. From the User setup window, select a
user ID to change.
2. From the User setup window, click
[Modify].
The Modify user window appears.
3. Change the &lt;User ID&gt;, &lt;Password&gt;,
&lt;Confirm password&gt;, and &lt;Level&gt; as
you wish.
4. Click [Apply].
The selected user ID will be changed.
To delete a user ID
1. From the User setup window, select a user ID to delete.
2. From the User setup window, click [Delete].
The selected user ID will be deleted.
M
 About the user permission
Administrator : Can use all functions (change/control settings).
Operator : Can use only the functions available in the Live Viewer.
User : Can only view the video on the Live Viewer.
To set the display language
1. Click &lt;Basic&gt; - &lt;Language&gt;.
The Language setup window appears.
You can select one from 7 languages
(English/Korean/Chinese/French/Italian/
Spanish/German).
2. When done, click [Apply].
The selected language will be applied.
54_ setup screen
SYSTEM SETUP
To set the date/time
You can obtain the current system time from the NTP server or your PC for your time
setting.
2. If you select Manual, input the date and
time manually.
Your settings will be saved.
y Current system time : The specified
time in System Time Setup will be
applied.
y System time setup : You can synchronize the system time with the NTP server (time
server) or your PC, or specify it manually.
M
 You can specify the time between January 1, 2000 and December 31, 2037.
To set the system time
1. Select a desired address in &lt;Address&gt;
or select &lt;Synchronize with PC
viewer&gt;.
2. If you select Manual, input the date and
time manually.
3. Click [Apply].
The specified system time will be applied.
M
 &lt;NTP Server IP&gt; is provided by a public agency, the list of which is subject to change from time
to time.
 In a local network, a separate NTP server must be manually defined.
J
 The current time can vary depending on the computers regional (GMT and DST) and country (PC
time configuration) settings.
English _55
● SETUP SCREEN
1. Select &lt;System&gt; - &lt;Date &amp; Time&gt;.
The Date &amp; Time setup window
appears.
setup screen
To check the log information
Select &lt;System&gt; - &lt;Log&gt;.
The Log information list appears.
y System log list : Shows the log
information about the system changes
along with time and IP address.
- User login : Shows the current login
user to the camera.
- Video configuration change : Show
video setting changes.
- System time change : Shows the time
changes.
- System started : Shows time when the camera is turned on.
M
 The maximum of 2000 logs can be recorded.
If the log number is over 2000, the log in the bottom of the log list will be replaced with a new log.
To update the software
Select &lt;System&gt; - &lt;Software update&gt;.
The Software update window appears.
How to update the software
1. From the software update window,
click [Browse…].
The Open dialog appears.
2. Select an updatable file and click
[Open].
3. From the software update window,
click [Install].
The selected file will be unzipped with a
start of the update.
It may take a several minutes to
complete the update.
56_ setup screen
4. When the software update is completed, you will be prompted to restart the system.
5. Click [OK] to restart the system.
Since the current connection is disconnected, you have to connect to the system
again.
J
 If the network is disconnected, the power supply fails, or the PC abnormally operates during the
update, the system does not work at all.
Restart or reset the system if it does not work properly or causes a problem.
Select &lt;System&gt; - &lt;Reset&gt;.
The Reset window appears.
y Restart : Restarts the system.
y Factory default : Resets the system
settings to the factory defaults with
following two options:
- Except network parameter : Resets all settings except for the Network Parameters.
- All : Restores all settings to the default.
This works the same as pressing the [RESET] button on the inside of the camera.
J
 After the system is reset or restarts, you should try to connect to the camera again.
 It takes several minutes until the system completes rebooting. Wait until the system rebooting is
completed and try to connect again.
 After executing &lt;Factory default&gt;, you must run the &lt;IP Installer.exe&gt; program to change the
basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to
the Internet.
To set the HTTPS
1. Select &lt;System&gt; - &lt;HTTPS&gt;.
The HTTPS setup window appears.
y Secure connection system : Select
a secure connection system to use.
To use the secure connection mode
requiring the public certificate for the
secure connection system, you must
have installed a signed certificate
issued by a certificate authority on
your system.
English _57
● SETUP SCREEN
To reset the system
setup screen
y Install a public certificate : To install the certificate to camera, you need to type a
certificate name (it can be arbitrarily assigned by user), certificate file issued from
the authority and a key file. When done, click [Install].
If the certificate is installed successfully, the user-defined certificate name will be
displayed. Also, the option button of &lt;HTTPS (Secure connection mode using
the public certificate)&gt; in the upper side becomes activated.
M
 To access the camera using HTTPS mode, you have to type the IP address for the camera in the
form of “https://&lt;Camera_IP&gt;”.
2. When done, click [Apply].
The web viewer will switch to the set secure connection system.
OVERLAY SETUP
You can display text on the screen.
To set the text
1. Select &lt;Overlay&gt; - &lt;Overlay text&gt;.
The Overlay Text setup window
appears.
2. When done, click [Apply].
Your settings will be saved.
y Overlay text settings : If you select
&lt;Disable&gt;, the overlay text will not
be displayed; If selecting &lt;Enable&gt;, it will display on the screen.
y Show date : Set to display the date information on the bottom screen.
- Output Format : Select a display format of the date information.
YYYY-MM-DD : Year-Month-Day / MM-DD-YYYY : Month-Day-Year/
DD-MM-YYYY : Day-Month-Year
y Show time : Set to display the time information on the bottom screen.
- Output Format : Select a display format of the time information.
24hr : Displays the time in the 24-hour format.
12hr : Displays the time in the 12-hour format.
y Text color : Select black or white for the text color.
y Background color : Select black or white for the background color.
58_ setup screen
EVENT SETUP
To set the event transfer function
You can set the FTP/email server (SMTP) to transfer the alarm images present in the
camera, in case an alarm event occurs.
Select &lt;Event&gt; - &lt;Transfer setup&gt;.
The Image transfer setup window appears.
● SETUP SCREEN
M
 For more information on commercial
SMTP services, contact the SMTP service
provider.
To test the FTP transfer
Click [Test].
This will test if the image is transferred to the
specified FTP server properly.
When the test on the FTP server connection
and transfer is done, a message of
&lt;( Verified )&gt; will be displayed.
You will see an error message if the test
fails. If this is the case, check the FTP server
status or the settings again.
y FTP transfer : With this, you can transfer alarm images to the FTP server. If the initial FTP
server setting and the connection status are not verified, the &lt;( Not verified )&gt; message
appears.
- Use passive mode : Select this option when the passive mode connection is
inevitable due to the firewall or FTP server setting.
- FTP server address : Enter the IP address of a FTP server to which an alarm image
will be transferred.
English _59
setup screen
- Upload path : You can specify the path of the FTP directory to which you will
transfer an alarm image.
You can specify the path by just typing &lt;/directory name&gt; or &lt;directory name&gt;
in this field.
If nothing is specified, the path will be defaulted to the root directory of the FTP
server.
- Port : The FTP port is defaulted to 21. This value can be changed according to the
FTP server setting.
- User ID : Provide the user account ID to access the FTP server.
- Password : Provide the user account password to access the FTP server.
y E-mail(SMTP) transfer : With this setting, you can transfer alarm images to the email
server. This function is available only for the SMTP email server. When the initial SMTP
server setting and connection are not verified, the &lt;Not verified&gt; message appears.
- SMTP server address : Enter the SMTP server address to use when you send an
email.
ex) 10.240.56.228
- Port : Enter a port number to use when you send an email. The default is 25.
- User ID : Provide the user account ID to access the SMTP server.
- Password : Provide the user account password to access the SMTP server.
- E-mail sender : Enter the address of the email sender. If the sender address is
incorrect, the email from the sender may be classified as SPAM by the SMTP
server and may not be sent.
- E-mail receiver : Enter the address of the email receiver.
- Title : Enter the subject of the email to send.
- Message : Enter the content of the email to send.
60_ setup screen
To test the email transfer
● SETUP SCREEN
Click [Test].
This will test if the image is transferred to the
specified SMTP server properly. When the
test on the SMTP server connection and
transfer is done, a message of &lt;( Verified )&gt;
will be displayed.
You will see an error message if the test
fails.
If this is the case, check the SMTP server
status or the settings again.
To setup the record
1. Click &lt;Event&gt; - &lt;Record setup&gt;.
The Record setup window appears.
2. To complete the setting, click the
[Apply] button.
The settings are saved.
y SD card : Enables you to verify data
saved on the SD memory card and
format the memory card itself.
It is possible to set to automatically delete movie clips recorded before a certain
period of time (e.g. 1 week, 1 month, or 1 year).
y Options : Determine whether or not you wish to receive Email notification of
insufficient capacity warnings.
English _61
setup screen
To set an alarm image
You can configure to send message via FTP/E-mail (SMTP) or to save recording into the
SD memory card.
Select a transfer method when an event occurs or the schedule transfer function is
activated.
1. Select &lt;Event&gt; - &lt;Alarm image&gt;.
The Alarm Image setup window
appears.
y Transfer mode : You can select
alarm message notification method
among FTP/E-mail transfer and SD
Card recording.
- FTP transfer : The image is sent to
the specified FTP address.
- E-mail transfer : The image is sent to the specified email address.
- SD Card Record : Saves images into the SD memory card.
M
If an SD memory card is not inserted, the corresponding button will be disabled.
In this case, insert the SD memory card into the slot and refresh to enable the button.
J
If the SD memory card is ejected while the button is checked, the camera automatically
restarts.
y Transferred image naming setup : You can set the file name of an alarm image
to be sent when an alarm is triggered or during the scheduled transfer.
y Pre/post alarm image : You can set to save the pre or post alarm image.
- Number of image : The frame rate per second can be one among 1, 2, 3, and 5.
- Pre-alarm duration : The pre alarm duration can be one among 5 seconds, 10
seconds, 15 seconds, and 30 seconds. You can send a pre-alarm image of up
to 30 seconds before the alarm is triggered.
(The max time differs, depending on the frame rate)
- Post-alarm duration : The post alarm duration can be one among 5 seconds, 10
seconds, 15 seconds, and 30 seconds. You can send a post-alarm image of up
to 30 seconds after the alarm is triggered.
(The max time differs, depending on the frame rate)
M
 The pre/post alarm duration is not available in SMTP transfer mode.
Only one image at the corresponding time will be transferred.
2. When done, click [Apply].
Your settings will be saved.
62_ setup screen
To set the alarm input
1. Select &lt;Event&gt; - &lt;Alarm input 1&gt; or
&lt;Alarm input 2&gt;.
The Alarm Input setup window appears.
English _63
● SETUP SCREEN
2. When done, click [Apply].
Your settings will be saved.
y Input device setup : Select an input
type according to the characteristics
of the alarm sensor on the rear of the
camera.
- Off : Turns off the alarm input setting.
- NO (Normal Open) : It is normally open, but if it is closed, an alarm will be triggered.
- NC (Normal Close) : It is normally closed, but if it is open, an alarm will be triggered.
y Activation time : You can set a time to execute a specific command when an
alarm occurs.
- Always : Always executes the specified command when an alarm occurs.
- Only scheduled time : Executes the specified command when an alarm occurs
only on a specified weekday, or time.
y Action : You can set an action to execute when an alarm occurs.
- Alarm output : Set the alarm output port to which the alarm signal is transferred.
- Output duration : Set the period of time to output the alarm signal to the
specified alarm output port when an alarm occurs.
If a new alarm event is detected during the alarm output, the delay time is
recalculated based on the detection time of the recent alarm.
- Alarm image transfer : If you select &lt;On&gt;, you can transfer JPEG images to a
registered address via FTP or SMTP server or save images into the SD memory card
according to the setting in &lt;Event&gt; - &lt;Transfer setup&gt;.
setup screen
To set the object counting function
1. Click the &lt;Event&gt; - &lt;Object counting&gt;.
The Object Counting Configuration
window is displayed.
2. To enable the object counting function,
select the &lt;Enable&gt; for the &lt;Object
counting function&gt;.
3. To display the line crossing or the area
occupancy in the monitoring video,
select the &lt;Enable&gt; for &lt;Overlay&gt;.
4. Set the Sensitivity for object detection.
5. Set the Line Crossing or the Area
Occupancy.
6. Set the Activation Time.
To set the object counting rules
1. Select your desired rule to set between
the &lt;Line Crossing&gt; or &lt;Area
Occupancy&gt;.
2. Set the line or area for the object
counting rule.
y Setting the line : Select the &lt;Line
Crossing&gt;, and then click your left
mouse button to draw the line in the
monitoring image in configuration screen.
If you complete drawing the line, click your right mouse button. Select one of the
lines displaying object motion directions in the dialog box, and then click the [OK]
button.
64_ setup screen
M
 You can draw the line to have maximum 11 dots.
 You must draw a threshold line so as to make room for an incoming object between threshold line
and image boundary .
If there is no room for the object between threshold and boundary, line crossing may not be enabled.
 If the distance between center of an object and threshold line stays at below a certain value after
y Deleting the line : Put the mouse cursor on the counting line in the monitoring
image in the &lt;Line Crossing&gt; configuration screen. When the Line Crossing
dialog box appears, click the [Delete] button.
y Setting the counting area : Select the &lt;Area Occupancy&gt;, and then click your left
mouse button to draw a polygon in the monitoring image in configuration screen.
If you complete drawing the polygon, click your right mouse button. When a
dialog box appears, click the [OK] button.
 You can set the counting area to a closed polygon with maximum 11 dots.
y Deleting the counting area : Put the mouse cursor on the counting area in the
monitoring image in the &lt;Area Occupancy&gt; configuration screen. When a dialog
box appears, click the [Delete] button.
3. Select the object size to be displayed in the monitoring image in configuration screen.
As the number gets bigger, the rectangle size for the object in the monitoring image
gets bigger.
If you set the object size small and an object with much bigger size appears, the
number of detected objects may be more than the actual.
4. Set the Activation Time.
y Always : Always enables the object counting function by designated setting.
y Only scheduled time : Enables the object counting function only at designated
time and day.
5. Set the File Transfer Interval.
y Counting interval : Save as a file the accumulative counting of objects that have
passed through the user-defined threshold line for a specific time as well as the
average of number of objects that have appeared in the counting area.
The average for the counting area will be updated in &lt;Object Counting&gt; &lt;Area&gt; at a certain time interval.
y File transfer interval : The CSV or XML file containing the results of counting at a
specified interval will be transferred to the server.
6. Specify the saving method of the result log.
y File Format: Select XML or CSV for the file format.
y Location : The position information of the camera will be attached to the file title
before sent to the server.
- You can enter only alphabets and number up to 15 characters.
English _65
● SETUP SCREEN
the object center passed through the threshold line, the object will not be counted even if it
passes over the threshold line again.
The distance value is proportional to the specified image size and &lt;Object Size&gt;.
If the image size is CIF (320x240), the distance corresponding to between 1 and 10 &lt;Object
Size&gt; will be 12, 15, 18, 21, 24, 27, 30, 33, 36 and 39 in pixels, respectively.
setup screen
7. Specify the contents of the file.
You can specify what’s included in the file.
8. When done, click [Apply].
J
 If the Object Counting function is activated, you cannot transfer the image or save it in SD card
M
 The following conditions may cause an error in object counting function or the object counting to
with Event function or Schedule Transfer function.
fail.
- If the light is continuously changed, the light is too strong, or shadow is too dark
- If the object does not satisfy the specified &lt;Object Size&gt; or a person, who is recognized as
an object, is creeping.
- If a person carries a heavy load such as shopping cart, big suitcase, etc.
- If several persons move together keeping close to each other
- If a person, who is recognized as an object, staying without any motion
(Ex. If a person keeps standing or sitting down without any motion)
- If shadow is too dark or the indoor illuminance is influenced by light such as lighting, sunlight, etc
- If the target object is reflected to the floor or wall; or if there is too dark shadow
(Ex. smooth marble floor, glass wall, etc.)
- If the camera is shaken
- If there is additional moving object other than the target object to count
(Ex. revolving door, waving curtain, etc.)
- If the size of object considerably varies from that of normal adult who is walking or running
(Ex. toddler, creeping person, too heavyset person, etc.)
- Several objects moves together (Ex. a person carrying a big object, a person in wheelchair,
people putting arms around each other's shoulders, etc.)
- If only part of the target object is displayed (Ex. a person located in the image boundary, a
person whose body is covered by specific structure, etc.)
66_ setup screen
To search for the count data
You can check the count data for up to 1 year by the searching method.
1. Select &lt;Event&gt; - &lt;Counting graph&gt;.
The Count Graph window appears.
● SETUP SCREEN
2. Before searching for the count graph,
check the followings below.
- SD Memory Card: Should be
unlocked before inserted.
- Alarm Image: The &lt;SD Card
Record&gt; item should be checked.
- The object counting function should
be operating or have operated in the
past.
3. Specify the search criteria and press
[Search].
To search for the latest data
1. Select Recent Search for the search
type.
2. If selecting the latest one month, you
can search for the latest 30 days of
data by the day.
3. If selecting the latest one week, you can search for the latest 7 days of data by the
day.
4. If selecting the latest one day, you can search for the latest 1 day of data by the hour.
5. If selecting the latest one hour, you can search for the latest 1 hour of data by 5
minutes.
To make a search for a selected range
1. Selective Search for the search type.
2. If selecting a specific year, you will make a search for the year by the month.
3. If selecting a specific month, you will make a search for the month by the day.
4. If selecting a specific day, you will make a search for the day by the hour.
5. If selecting a specific hour, you will make a search for the hour by 5 minutes.
English _67
setup screen
To make a search for a specific period
1. Select Period Search for the search type.
2. If selecting the yearly search, you will make a search for the specified period by the year.
3. If selecting the monthly search, you will make a search for the specified period by
the month.
4. If selecting the daily search, you will make a search for the specified period by the day.
To search for the average data for a specific period
1. Select Average Search for the search type.
2. If selecting the daily average search, you will make a search for the daily average data
for the specified period.
3. If selecting the hourly average search, you will make a search for the hourly average
data for the specified period.
To view a desired data item
1. From the top right corner of the result graph, select or deselect the checkboxes:
Line In, Line Out or Area.
To output the search results as a file
1. Click [Export] from the bottom right corner of the result graph.
2. The search results will be saved to the “C:\CountingLog\Counting.csv” file.
68_ setup screen
To set the scheduled transfer
You can set to transfer the JPEG image to the FTP/SMTP server saved in the SD memory
card at a specific interval.
2. When done, click [Apply].
Your settings will be saved.
English _69
● SETUP SCREEN
1. Select &lt;Event&gt; - &lt;Schedule&gt;.
The Schedule Transfer setup window
appears.
y Schedule transfer function :
If selecting &lt;Enable&gt;, the schedule
transfer function will be activated;
if selecting &lt;Disable&gt;, it will be
deactivated.
y Transfer interval : You can set the
time interval to transfer images.
You can set the unit of the interval to &lt;seconds&gt; or &lt;minutes&gt;; you can also set to
transfer one image per 5/15/30/45/60 seconds, or one per 5/15/30/45/60 minutes.
y Activation time : You can set a time to execute a specific command when a schedule transfer event occurs.
- Always : Always sends an image at the set interval.
- Only scheduled time : Sends the image only on a specified weekday, or time.
setup screen
NETWORK SETUP
To set the video transfer mode
You can control the transfer rate according to the video transfer mode and network speed.
1. Select &lt;Network&gt; - &lt;Streaming type&gt;.
The Video Transfer setup window
appears.
2. When done, click [Apply].
Your settings will be saved.
y VNP streaming : You can set the
Samsung Protocol (VNP) for the streaming service.
- Protocol : Select a video transfer protocol from TCP*, UDP (Unicast)*, and UDP
(Multicast)*.
 Multicast backbone (MBone) is not supported; you can access the camera only in the
multicast local network environment.
y RTP streaming : You can set the RTP Protocol or the streaming service.
- Protocol : Select a video transfer protocol from UDP (Unicast) and UDP (Multicast).
To set the DDNS
DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address
of a camera into a general Host Name so that the user can easily remember it and enables
connecting a camera with a fixed Host Name even if the IP address of the camera may be
dynamically changed.
1. Select &lt;Network&gt; - &lt;DDNS&gt;.
The DDNS setup window appears.
2. When done, click [Apply].
Your settings will be saved.
M
 For checking the DDNS address, refer to
“To check the DDNS address”.
(page 42)
70_ setup screen
appendix
PROFILE
CAMERA SETUP MENU
STANDARD
ITS
ALC
ALC
ALC
-
-
-
DC
DC
DC
GAMING
BANK
ALC
ALC
ALC
-
-
-
DC
DC
DC
BACKLIGHT DAY/NIGHT
Parent Menu Sub-menus
IRIS
LENS
LEVEL
BACKLIGHT
MOTION
0
0
0
0
0
0
OFF
OFF
WDR
OFF
OFF
WDR
(F.FAST)
---
(F.FAST)
---
NORM
(F.FAST)
---
SLOW
(F.FAST)
---
DNR
MID
MID
MID
MID
MID
MID
SHUTTER
OFF
AUTO 1/250
OFF
OFF
OFF
OFF
SENSE UP
AUTO X4
AUTO X2
AUTO X4
AUTO X4
AUTO X4
AUTO X4
XDR
MID
MID
MID
MID
MID
MID
AUTO
AUTO
DAY
AUTO
DAY
AUTO
DAY/NIGHT NIGHT
-
-
-
-
-
-
OFF
ON
OFF
OFF
OFF
OFF
DAY
DAY/NIGHT
DAY
DAY/NIGHT
DAY
DAY
-
-
-
-
-
-
MODE
ATW2
ATW1
ATW1
ATW1
ATW1
ATW2
RED
0
0
0
0
0
0
BLUE
0
0
0
0
0
0
-
-
-
-
-
-
MID
Custom Setting
MID
ATW2
OFF
ATW2
0
Custom Setting
0
Custom Setting Custom Setting
0
Custom Setting
0
Custom Setting Custom Setting
2
2
2
BURST
DAY
WHITE BAL
NIGHT
BRIGHTNESS Custom Setting
MODE
OFF
RED Custom Setting
BLUE Custom Setting
DETAIL
2
Custom Setting Custom Setting
OFF
2
OFF
2
English _71
● APPENDIX
ALC
appendix
TERMINOLOGY
y GOP : The default is 15, and if set to 15, one I-Frame will be output per 15 frames as one
I-Frame and 14 P-Frames constitute the GOP.
The lower the GOP size is, the better the quality is; however, the bit rate as well as the data
size will increase, causing a lower of the fps. GOP(Group of Pictures) is a set of video frames
for MPEG4 and H.264 format compression, indicating a collection of frames from the initial
I-Frame (key frame) to the next I-Frame. GOP consists of 2 kinds of frames: I-Frame and
P-Frame. I-Frame is the basic frame for the compression, also known as Key Frame, which
contains one complete image data. P-Frame contains only the data that has changed from
the preceding I-Frame.
y Entropy coding : Data transfer technology used to reduce the compression loss from encoding.
- CAVLC (Context-adaptive variable-length coding): Records a higher compression loss
rate than CABAC.
- CABAC (Context-adaptive binary arithmetic coding): Shows a lesser compression loss than
CAVLC.
y Bitrate Control
- CBR(Constant Bitrate)
This will transfer video data in an equal size at all times, regardless of the video
complexity. The video quality may be deteriorated, depending on the video complexity.
- VBR(Variable Bitrate)
The amount of video data to transfer may differ, depending on the video complexity. This
enables receiving video data in an equal quality at all times.
y TTL : TTL stands for “Time To Live”, which you can specify to prevent loss of data packet that
passes through multiple-staged routers. Each router decreases the TTL value by one each
time a packet passes it through; If the TTL value reaches 0, the packet cannot further pass
through a router.
y TCP : It is a general purpose protocol used for transmission that requires reliability. With
constant communication between the sender and recipient, it provides high reliability against
transmission data loss; however, it has imitation to transmit a large amount of data in real time
at a high speed.
It enables reliable data transmission over xDSL and cable network at a relatively slow speed.
y UDP (Unicast): It refers to a system that transmits data between only one transmitter and one
receiver (1:1).
y UDP (Multicast): It refers to the data transfer protocol in one-to-many (1:N) between the transmitting and receiving terminals; although it alleviates the network load, it requires &lt;Multicast&gt;
router.
For more information such as whether the network over which the camera is installed supports &lt;Multicast&gt;, contact the network administrator.
y UDP : It is a protocol appropriate to transmit a large amount of data such as multimedia data at a
high speed. However, with its nonconnection structure, it records a higher transmission efficiency
than TCP especially in a high LAN environment faster than 100Mbps.
72_ appendix
SPECIFICATIONS
Description
Item
Camera
Type
Scanning
Color/BW
Color
Device
1/3&quot; Super-HAD PS CCD
811 x 508
768 x 494
Progressive
15.734 Hz
59.94 Hz
Pixels
Total
Effective
System
Horizontal Frequency
Vertical Frequency
795 x 596
752 x 582
15.625 Hz
50 Hz
Color
Sens off : 0.12 Lux(15 IRE), 0.2 Lux(30 IRE),
0.4Lux(50 IRE)@F1.2
Sens up x512 : 0.00023 Lux(15 IRE), 0.0005 Lux(30 IRE),
0.0008 Lux(50 IRE)@F1.2
B/W
Sens off : 0.012 Lux(15 IRE), 0.02 Lux(30 IRE),
0.04Lux(50 IRE)@F1.2
Sens up x512 : 0.000023 Lux(15 IRE), 0.00005 Lux(30 IRE),
0.00008 Lux(50 IRE)@F1.2
Number of Privacy Zone
Day/Night
Extended Dynamic Range
WDR
D-Zoom
PIP
High Speed Shutter
Flickerless
Sens Up
BLC
AGC
Camera ID
White Balance
Digital Noise Reduction
Digital Image Stablization
Etc. Function
12 ea
Day/Night/AUTO(Soft Method)
Off/On (Level Setting)
Off/On (128)
Off/On (160)
x1 ~ x16 (x0.1 STEP)
Off/On (Advanced)
1/60 ~ 1/10Ksec
1/50 ~ 1/10Ksec
Off/On
x2 ~ x512
Off/On (Area Setting)
Off/On (Max.Level Setting)
Off/On (Max.54ea/2Line)
ATW1/ATW2/AWC/MANUAL
Off/On (Adaptive 3D+2D)
Off/On
Detail, Reverse(H/V), Posi/Nega
Min. Scene
Illumination
Functions
PAL
● APPENDIX
Image
NTSC
English _73
appendix
Description
Item
NTSC
Horizontal
600 TV Lines
Vertical
350 TV Lines
PAL
Resolution
Video Output Video Output
VBS 1.0Vp-p
S/N Ratio
S/N Ratio
about 52 dB
Lens Drive Type
AI (DC)
Mount Type
Board Type
Lens
OS
Network
Board
Hardware
Embedded Linux
Flash memory
32M byte
RAM
256M byte
DSP
TI Davinci
Ethernet
RJ-45 (10/100BASE-T)
PoE
Yes (IEEE802.3af)
Input
2 ea
Output
2 ea
Compression
H.264 / MPEG4 / MJPEG Multiple Codec
(H.264 / MPEG4 selectable)
Simultaneous Dual Streaming
Alarm
Video
Resolution
4CIF
704x480
VGA
640x480
CIF
704x576
352x240
352x288
Frame Rate
30, 15, 8, 3, 1 fps
25, 13, 6, 3, 1 fps
Quality
1 ~ 10 level
OSD
Camera Control and Adjustment
OSD menu on Video
(Menu enter/exit, move by Web UI)
* Some key adjustment menus will be supported by CGI API.
Object
Counting
Set Rules
Line Crossing, Area Occupancy
74_ appendix
Description
Item
NTSC
IP
Network
Protocol
IPv4
TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTSP, NTP, HTTP,
HTTPS, SSL, DHCP
PPPoE, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2),
ARP, DNS, DDNS, VSIP
IPv6
TCP/IP, HTTP, HTTPS, SSL, DHCP
Streaming
Unicast (TCP, UDP), Multicast (UDP)
Security
HTTPS Login Authentication
Digest Login Authentication
DDNS
Supporting Samsung DDNS and Public DDNS services
Maximum User Access
Connection
Administrator
User Access
Level
Video Player
Live Monitoring, Alarm I/O control
User
Live Monitoring
JPEG Image transfer : FTP, SMTP, SD Card
Notification : notify to viewer or by E-mail (one image
attachment)
Alarm Out
Schedule
JPEG Image transfer : FTP, SMTP, SD Card
Supported OS
Windows XP, Windows VISTA, Windows 7
Supported Browser
Internet Explorer 6.0 or Higher
UI Language
E/F/G/S/I/C/K
S/W upgrade
Support
RTP/RTSP streaming
Quicktime, VLC player
Video
Management
Software
Application
Max 10 Users at Unicast (TCP, UDP) Mode
Max 20 Users at Multicast (UDP) Mode
Live Monitoring, Alarm I/O control, OSD menu control,
SETUP
Operator
Alarm Input
Event
Management
Web
Browser
Viewer
(Default)
● APPENDIX
Protocol
PAL
IPv4 / IPv6
Samsung iPOLiS
3rd Party S/W appliction
IP Installation
IP Installer Application for All Samsung IP Devices
English _75
appendix
Item
HTTP API
CGI Command
SDK
RTP/RTSP API
ActiveX
Description
NTSC
PAL
Provides functionality to control cameras and set/retrieve
internal parameter values.
Get JPEG image or MJPEG stream
Alarm In/Out control
RTP Header, RTSP Command Document
SDK
ActiveX API for viewing data streams from IP camera.
AC24V&plusmn;10%(60Hz&plusmn;0.3Hz)
AC24V&plusmn;10%(50Hz&plusmn;0.3Hz)
Power
DC12V+10%/-5% / PoE (Power over Ethernet)
Power Consumption
Max. 8W
Operating Temp.
-10˚C~50˚C
Operating Humidity
~90%
Dimension (&Oslash; x H)
159.9(&Oslash;) x 125.0(H)mm
Weight
About 650g
76_ appendix
FRAME RATE (NTSC)
 Test Condition: MJPEG - Resolution(CIF), Quality(1), Frame rate(1)
M
❖ MPEG4 (4CIF)
Frame Rate
30 FPS
15 FPS
8 FPS
3 FPS
1 FPS
LEVEL10
4239 Kbps
23 FPS
2765 Kbps
15 FPS
1290 Kbps
7 FPS
737 Kbps
4 FPS
221 Kbps
1 FPS
LEVEL9
3686 Kbps
24 FPS
2304 Kbps
15 FPS
1075 Kbps
7 FPS
614 Kbps
4 FPS
184 Kbps
1 FPS
LEVEL8
3072 Kbps
25 FPS
1843 Kbps
15 FPS
860 Kbps
7 FPS
492 Kbps
4 FPS
147 Kbps
1 FPS
LEVEL7
2396 Kbps
26 FPS
1382 Kbps
15 FPS
645 Kbps
7 FPS
369 Kbps
4 FPS
111 Kbps
1 FPS
LEVEL6
1659 Kbps
27 FPS
922 Kbps
15 FPS
430 Kbps
7 FPS
246 Kbps
4 FPS
74 Kbps
1 FPS
LEVEL5
1336 Kbps
29 FPS
691 Kbps
15 FPS
323 Kbps
7 FPS
184 Kbps
4 FPS
55 Kbps
1 FPS
LEVEL4
1133 Kbps
30 FPS
576 Kbps
15 FPS
269 Kbps
7 FPS
154 Kbps
4 FPS
46 Kbps
1 FPS
LEVEL3
922 Kbps
30 FPS
461 Kbps
15 FPS
215 Kbps
7 FPS
123 Kbps
4 FPS
37 Kbps
1 FPS
LEVEL2
691 Kbps
30 FPS
346 Kbps
15 FPS
161 Kbps
7 FPS
92 Kbps
4 FPS
28 Kbps
1 FPS
LEVEL1
461 Kbps
30 FPS
230 Kbps
15 FPS
108 Kbps
7 FPS
61 Kbps
4 FPS
18 Kbps
1 FPS
Quality
English _77
● APPENDIX
H.264 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate),
GOP size(15), Deblock(ON), Profile(Baseline), Entropy coding(CAVLC), Motion
estimation(HPel)
MPEG4 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate),
De-Interlace(ON), GOP size(15)
appendix
❖ H.264 (4CIF)
Frame Rate
30 FPS
15 FPS
8 FPS
3 FPS
1 FPS
LEVEL10
2298 Kbps
19 FPS
1229 Kbps
10 FPS
737 Kbps
6 FPS
369 Kbps
3 FPS
147 Kbps
1 FPS
LEVEL9
1751 Kbps
19 FPS
1198 Kbps
13 FPS
645 Kbps
7 FPS
369 Kbps
4 FPS
111 Kbps
1 FPS
LEVEL8
1536 Kbps
20 FPS
1075 Kbps
14 FPS
538 Kbps
7 FPS
307 Kbps
4 FPS
92 Kbps
1 FPS
LEVEL7
1352 Kbps
22 FPS
897 Kbps
15 FPS
430 Kbps
7 FPS
246 Kbps
4 FPS
74 Kbps
1 FPS
LEVEL6
1129 Kbps
25 FPS
691 Kbps
15 FPS
369 Kbps
8 FPS
184 Kbps
4 FPS
55 Kbps
1 FPS
LEVEL5
960 Kbps
25 FPS
576 Kbps
15 FPS
307 Kbps
8 FPS
154 Kbps
4 FPS
46 Kbps
1 FPS
LEVEL4
799 Kbps
26 FPS
461 Kbps
15 FPS
246 Kbps
8 FPS
123 Kbps
4 FPS
37 Kbps
1 FPS
LEVEL3
622 Kbps
27 FPS
346 Kbps
15 FPS
184 Kbps
8 FPS
92 Kbps
4 FPS
28 Kbps
1 FPS
LEVEL2
445 Kbps
29 FPS
230 Kbps
15 FPS
123 Kbps
8 FPS
61 Kbps
4 FPS
18 Kbps
1 FPS
LEVEL1
223 Kbps
29 FPS
115 Kbps
15 FPS
61 Kbps
8 FPS
31 Kbps
4 FPS
9 Kbps
1 FPS
Quality
78_ appendix
❖ MPEG4 (VGA)
Frame Rate
15 FPS
8 FPS
3 FPS
1 FPS
LEVEL10
2580 Kbps
14 FPS
1290 Kbps
7 FPS
737 Kbps
4 FPS
221 Kbps
1 FPS
LEVEL9
3533 Kbps
23 FPS
2304 Kbps
15 FPS
1075 Kbps
7 FPS
614 Kbps
4 FPS
184 Kbps
1 FPS
LEVEL8
2949 Kbps
24 FPS
1843 Kbps
15 FPS
860 Kbps
7 FPS
492 Kbps
4 FPS
147 Kbps
1 FPS
LEVEL7
2304 Kbps
25 FPS
1382 Kbps
15 FPS
645 Kbps
7 FPS
369 Kbps
4 FPS
111 Kbps
1 FPS
LEVEL6
1536 Kbps
25 FPS
922 Kbps
15 FPS
430 Kbps
7 FPS
246 Kbps
4 FPS
74 Kbps
1 FPS
LEVEL5
1152 Kbps
25 FPS
691 Kbps
15 FPS
323 Kbps
7 FPS
184 Kbps
4 FPS
55 Kbps
1 FPS
LEVEL4
998 Kbps
26 FPS
576 Kbps
15 FPS
269 Kbps
7 FPS
154 Kbps
4 FPS
46 Kbps
1 FPS
LEVEL3
799 Kbps
26 FPS
461 Kbps
15 FPS
246 Kbps
8 FPS
123 Kbps
4 FPS
37 Kbps
1 FPS
LEVEL2
622 Kbps
27 FPS
346 Kbps
15 FPS
184 Kbps
8 FPS
92 Kbps
4 FPS
28 Kbps
1 FPS
LEVEL1
415 Kbps
27 FPS
230 Kbps
15 FPS
123 Kbps
8 FPS
61 Kbps
4 FPS
18 Kbps
1 FPS
English _79
● APPENDIX
30 FPS
4055 Kbps
22 FPS
Quality
appendix
❖ H.264 (VGA)
Frame Rate
30 FPS
15 FPS
8 FPS
3 FPS
1 FPS
LEVEL10
2089 Kbps
17 FPS
1229 Kbps
10 FPS
737 Kbps
6 FPS
369 Kbps
3 FPS
147 Kbps
1 FPS
LEVEL9
1659 Kbps
18 FPS
1014 Kbps
11 FPS
553 Kbps
6 FPS
276 Kbps
3 FPS
111 Kbps
1 FPS
LEVEL8
1459 Kbps
19 FPS
845 Kbps
11 FPS
538 Kbps
7 FPS
307 Kbps
4 FPS
92 Kbps
1 FPS
LEVEL7
1229 Kbps
20 FPS
737 Kbps
12 FPS
430 Kbps
7 FPS
246 Kbps
4 FPS
74 Kbps
1 FPS
LEVEL6
1014 Kbps
22 FPS
691 Kbps
15 FPS
323 Kbps
7 FPS
184 Kbps
4 FPS
55 Kbps
1 FPS
LEVEL5
883 Kbps
23 FPS
576 Kbps
15 FPS
269 Kbps
7 FPS
154 Kbps
4 FPS
46 Kbps
1 FPS
LEVEL4
707 Kbps
23 FPS
461 Kbps
15 FPS
215 Kbps
7 FPS
123 Kbps
4 FPS
37 Kbps
1 FPS
LEVEL3
553 Kbps
24 FPS
346 Kbps
15 FPS
161 Kbps
7 FPS
92 Kbps
4 FPS
28 Kbps
1 FPS
LEVEL2
384 Kbps
25 FPS
230 Kbps
15 FPS
108 Kbps
7 FPS
61 Kbps
4 FPS
18 Kbps
1 FPS
LEVEL1
200 Kbps
26 FPS
115 Kbps
15 FPS
54 Kbps
7 FPS
31 Kbps
4 FPS
9 Kbps
1 FPS
Quality
80_ appendix
❖ MPEG4 (CIF)
Frame Rate
15 FPS
8 FPS
3 FPS
1 FPS
LEVEL10
691 Kbps
15 FPS
369 Kbps
8 FPS
184 Kbps
4 FPS
55 Kbps
1 FPS
LEVEL9
1152 Kbps
30 FPS
576 Kbps
15 FPS
307 Kbps
8 FPS
154 Kbps
4 FPS
46 Kbps
1 FPS
LEVEL8
922 Kbps
30 FPS
461 Kbps
15 FPS
246 Kbps
8 FPS
123 Kbps
4 FPS
37 Kbps
1 FPS
LEVEL7
691 Kbps
30 FPS
346 Kbps
15 FPS
184 Kbps
8 FPS
92 Kbps
4 FPS
28 Kbps
1 FPS
LEVEL6
461 Kbps
30 FPS
230 Kbps
15 FPS
123 Kbps
8 FPS
61 Kbps
4 FPS
18 Kbps
1 FPS
LEVEL5
346 Kbps
30 FPS
173 Kbps
15 FPS
92 Kbps
8 FPS
46 Kbps
4 FPS
14 Kbps
1 FPS
LEVEL4
288 Kbps
30 FPS
144 Kbps
15 FPS
77 Kbps
8 FPS
38 Kbps
4 FPS
12 Kbps
1 FPS
LEVEL3
230 Kbps
30 FPS
115 Kbps
15 FPS
61 Kbps
8 FPS
31 Kbps
4 FPS
9 Kbps
1 FPS
LEVEL2
173 Kbps
30 FPS
86 Kbps
15 FPS
46 Kbps
8 FPS
23 Kbps
4 FPS
7 Kbps
1 FPS
LEVEL1
151 Kbps
30 FPS
76 Kbps
15 FPS
40 Kbps
8 FPS
20 Kbps
4 FPS
6 Kbps
1 FPS
English _81
● APPENDIX
30 FPS
1382 Kbps
30 FPS
Quality
appendix
❖ H.264 (CIF)
Frame Rate
30 FPS
15 FPS
8 FPS
3 FPS
1 FPS
LEVEL10
922 Kbps
30 FPS
461 Kbps
15 FPS
215 Kbps
7 FPS
123 Kbps
4 FPS
37 Kbps
1 FPS
LEVEL9
691 Kbps
30 FPS
346 Kbps
15 FPS
184 Kbps
8 FPS
92 Kbps
4 FPS
28 Kbps
1 FPS
LEVEL8
576 Kbps
30 FPS
288 Kbps
15 FPS
134 Kbps
7 FPS
77 Kbps
4 FPS
23 Kbps
1 FPS
LEVEL7
461 Kbps
30 FPS
230 Kbps
15 FPS
108 Kbps
7 FPS
61 Kbps
4 FPS
18 Kbps
1 FPS
LEVEL6
346 Kbps
30 FPS
173 Kbps
15 FPS
81 Kbps
7 FPS
46 Kbps
4 FPS
14 Kbps
1 FPS
LEVEL5
288 Kbps
30 FPS
144 Kbps
15 FPS
67 Kbps
7 FPS
38 Kbps
4 FPS
12 Kbps
1 FPS
LEVEL4
230 Kbps
30 FPS
115 Kbps
15 FPS
54 Kbps
7 FPS
31 Kbps
4 FPS
9 Kbps
1 FPS
LEVEL3
173 Kbps
30 FPS
86 Kbps
15 FPS
40 Kbps
7 FPS
23 Kbps
4 FPS
7 Kbps
1 FPS
LEVEL2
115 Kbps
30 FPS
58 Kbps
15 FPS
27 Kbps
7 FPS
15 Kbps
4 FPS
5 Kbps
1 FPS
LEVEL1
58 Kbps
30 FPS
29 Kbps
15 FPS
13 Kbps
7 FPS
8 Kbps
4 FPS
2 Kbps
1 FPS
Quality
82_ appendix
FRAME RATE (PAL)
 Test Condition: MJPEG - Resolution(CIF), Quality(1), Frame rate(1)
M
❖ MPEG4 (4CIF)
Frame Rate
25 FPS
13 FPS
6 FPS
3 FPS
1 FPS
LEVEL10
4645 Kbps
21 FPS
2654 Kbps
12 FPS
1327 Kbps
6 FPS
664 Kbps
3 FPS
221 Kbps
1 FPS
LEVEL9
4055 Kbps
22 FPS
2212 Kbps
12 FPS
1106 Kbps
6 FPS
553 Kbps
3 FPS
184 Kbps
1 FPS
LEVEL8
3391 Kbps
23 FPS
1769 Kbps
12 FPS
885 Kbps
6 FPS
442 Kbps
3 FPS
147 Kbps
1 FPS
LEVEL7
2544 Kbps
23 FPS
1327 Kbps
12 FPS
664 Kbps
6 FPS
332 Kbps
3 FPS
111 Kbps
1 FPS
LEVEL6
1769 Kbps
24 FPS
885 Kbps
12 FPS
442 Kbps
6 FPS
221 Kbps
3 FPS
74 Kbps
1 FPS
LEVEL5
1382 Kbps
25 FPS
664 Kbps
12 FPS
332 Kbps
6 FPS
166 Kbps
3 FPS
55 Kbps
1 FPS
LEVEL4
1152 Kbps
25 FPS
553 Kbps
12 FPS
276 Kbps
6 FPS
138 Kbps
3 FPS
46 Kbps
1 FPS
LEVEL3
922 Kbps
25 FPS
442 Kbps
12 FPS
221 Kbps
6 FPS
111 Kbps
3 FPS
37 Kbps
1 FPS
LEVEL2
691 Kbps
25 FPS
332 Kbps
12 FPS
166 Kbps
6 FPS
83 Kbps
3 FPS
28 Kbps
1 FPS
LEVEL1
461 Kbps
25 FPS
221 Kbps
12 FPS
111 Kbps
6 FPS
55 Kbps
3 FPS
18 Kbps
1 FPS
Quality
English _83
● APPENDIX
H.264 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate),
GOP size(15), Deblock(ON), Profile(Baseline), Entropy coding(CAVLC), Motion
estimation(HPel)
MPEG4 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate),
De-Interlace(ON), GOP size(15)
appendix
❖ H.264 (4CIF)
Frame Rate
25 FPS
13 FPS
6 FPS
3 FPS
1 FPS
LEVEL10
2359 Kbps
16 FPS
1180 Kbps
8 FPS
737 Kbps
5 FPS
442 Kbps
3 FPS
147 Kbps
1 FPS
LEVEL9
1991 Kbps
18 FPS
1106 Kbps
10 FPS
664 Kbps
6 FPS
332 Kbps
3 FPS
111 Kbps
1 FPS
LEVEL8
1751 Kbps
19 FPS
1014 Kbps
11 FPS
553 Kbps
6 FPS
276 Kbps
3 FPS
92 Kbps
1 FPS
LEVEL7
1475 Kbps
20 FPS
885 Kbps
12 FPS
442 Kbps
6 FPS
221 Kbps
3 FPS
74 Kbps
1 FPS
LEVEL6
1161 Kbps
21 FPS
664 Kbps
12 FPS
332 Kbps
6 FPS
166 Kbps
3 FPS
55 Kbps
1 FPS
LEVEL5
968 Kbps
21 FPS
553 Kbps
12 FPS
276 Kbps
6 FPS
138 Kbps
3 FPS
46 Kbps
1 FPS
LEVEL4
811 Kbps
22 FPS
442 Kbps
12 FPS
221 Kbps
6 FPS
111 Kbps
3 FPS
37 Kbps
1 FPS
LEVEL3
608 Kbps
22 FPS
332 Kbps
12 FPS
166 Kbps
6 FPS
83 Kbps
3 FPS
28 Kbps
1 FPS
LEVEL2
424 Kbps
23 FPS
221 Kbps
12 FPS
111 Kbps
6 FPS
55 Kbps
3 FPS
18 Kbps
1 FPS
LEVEL1
230 Kbps
25 FPS
111 Kbps
12 FPS
55 Kbps
6 FPS
28 Kbps
3 FPS
9 Kbps
1 FPS
Quality
84_ appendix
❖ MPEG4 (VGA)
Frame Rate
13 FPS
6 FPS
3 FPS
1 FPS
LEVEL10
2654 Kbps
12 FPS
1327 Kbps
6 FPS
664 Kbps
3 FPS
221 Kbps
1 FPS
LEVEL9
3871 Kbps
21 FPS
2212 Kbps
12 FPS
1106 Kbps
6 FPS
553 Kbps
3 FPS
184 Kbps
1 FPS
LEVEL8
3097 Kbps
21 FPS
1769 Kbps
12 FPS
885 Kbps
6 FPS
442 Kbps
3 FPS
147 Kbps
1 FPS
LEVEL7
2433 Kbps
22 FPS
1327 Kbps
12 FPS
664 Kbps
6 FPS
332 Kbps
3 FPS
111 Kbps
1 FPS
LEVEL6
1769 Kbps
24 FPS
885 Kbps
12 FPS
442 Kbps
6 FPS
221 Kbps
3 FPS
74 Kbps
1 FPS
LEVEL5
1382 Kbps
25 FPS
664 Kbps
12 FPS
332 Kbps
6 FPS
166 Kbps
3 FPS
55 Kbps
1 FPS
LEVEL4
1152 Kbps
25 FPS
553 Kbps
12 FPS
276 Kbps
6 FPS
138 Kbps
3 FPS
46 Kbps
1 FPS
LEVEL3
922 Kbps
25 FPS
442 Kbps
12 FPS
221 Kbps
6 FPS
111 Kbps
3 FPS
37 Kbps
1 FPS
LEVEL2
691 Kbps
25 FPS
332 Kbps
12 FPS
166 Kbps
6 FPS
83 Kbps
3 FPS
28 Kbps
1 FPS
LEVEL1
461 Kbps
25 FPS
221 Kbps
12 FPS
111 Kbps
6 FPS
55 Kbps
3 FPS
18 Kbps
1 FPS
English _85
● APPENDIX
25 FPS
4424 Kbps
20 FPS
Quality
appendix
❖ H.264 (VGA)
Frame Rate
25 FPS
13 FPS
6 FPS
3 FPS
1 FPS
LEVEL10
2507 Kbps
17 FPS
1327 Kbps
9 FPS
737 Kbps
5 FPS
442 Kbps
3 FPS
147 Kbps
1 FPS
LEVEL9
1991 Kbps
18 FPS
1217 Kbps
11 FPS
664 Kbps
6 FPS
332 Kbps
3 FPS
111 Kbps
1 FPS
LEVEL8
1659 Kbps
18 FPS
1106 Kbps
12 FPS
553 Kbps
6 FPS
276 Kbps
3 FPS
92 Kbps
1 FPS
LEVEL7
1401 Kbps
19 FPS
885 Kbps
12 FPS
442 Kbps
6 FPS
221 Kbps
3 FPS
74 Kbps
1 FPS
LEVEL6
1106 Kbps
20 FPS
664 Kbps
12 FPS
332 Kbps
6 FPS
166 Kbps
3 FPS
55 Kbps
1 FPS
LEVEL5
968 Kbps
21 FPS
553 Kbps
12 FPS
276 Kbps
6 FPS
138 Kbps
3 FPS
46 Kbps
1 FPS
LEVEL4
774 Kbps
21 FPS
442 Kbps
12 FPS
221 Kbps
6 FPS
111 Kbps
3 FPS
37 Kbps
1 FPS
LEVEL3
608 Kbps
22 FPS
332 Kbps
12 FPS
166 Kbps
6 FPS
83 Kbps
3 FPS
28 Kbps
1 FPS
LEVEL2
424 Kbps
23 FPS
221 Kbps
12 FPS
111 Kbps
6 FPS
55 Kbps
3 FPS
18 Kbps
1 FPS
LEVEL1
230 Kbps
25 FPS
111 Kbps
12 FPS
55 Kbps
6 FPS
28 Kbps
3 FPS
9 Kbps
1 FPS
Quality
86_ appendix
❖ MPEG4 (CIF)
Frame Rate
13 FPS
6 FPS
3 FPS
1 FPS
LEVEL10
664 Kbps
12 FPS
332 Kbps
6 FPS
166 Kbps
3 FPS
55 Kbps
1 FPS
LEVEL9
1152 Kbps
25 FPS
553 Kbps
12 FPS
276 Kbps
6 FPS
138 Kbps
3 FPS
46 Kbps
1 FPS
LEVEL8
922 Kbps
25 FPS
442 Kbps
12 FPS
221 Kbps
6 FPS
111 Kbps
3 FPS
37 Kbps
1 FPS
LEVEL7
691 Kbps
25 FPS
332 Kbps
12 FPS
166 Kbps
6 FPS
83 Kbps
3 FPS
28 Kbps
1 FPS
LEVEL6
461 Kbps
25 FPS
221 Kbps
12 FPS
111 Kbps
6 FPS
55 Kbps
3 FPS
18 Kbps
1 FPS
LEVEL5
346 Kbps
25 FPS
166 Kbps
12 FPS
83 Kbps
6 FPS
41 Kbps
3 FPS
14 Kbps
1 FPS
LEVEL4
288 Kbps
25 FPS
138 Kbps
12 FPS
69 Kbps
6 FPS
35 Kbps
3 FPS
12 Kbps
1 FPS
LEVEL3
230 Kbps
25 FPS
111 Kbps
12 FPS
55 Kbps
6 FPS
28 Kbps
3 FPS
9 Kbps
1 FPS
LEVEL2
173 Kbps
25 FPS
83 Kbps
12 FPS
41 Kbps
6 FPS
21 Kbps
3 FPS
7 Kbps
1 FPS
LEVEL1
151 Kbps
25 FPS
73 Kbps
12 FPS
36 Kbps
6 FPS
18 Kbps
3 FPS
6 Kbps
1 FPS
English _87
● APPENDIX
25 FPS
1382 Kbps
25 FPS
Quality
appendix
❖ H.264 (CIF)
Frame Rate
25 FPS
13 FPS
6 FPS
3 FPS
1 FPS
LEVEL10
922 Kbps
25 FPS
442 Kbps
12 FPS
221 Kbps
6 FPS
111 Kbps
3 FPS
37 Kbps
1 FPS
LEVEL9
691 Kbps
25 FPS
332 Kbps
12 FPS
166 Kbps
6 FPS
83 Kbps
3 FPS
28 Kbps
1 FPS
LEVEL8
576 Kbps
25 FPS
276 Kbps
12 FPS
138 Kbps
6 FPS
69 Kbps
3 FPS
23 Kbps
1 FPS
LEVEL7
461 Kbps
25 FPS
221 Kbps
12 FPS
111 Kbps
6 FPS
55 Kbps
3 FPS
18 Kbps
1 FPS
LEVEL6
346 Kbps
25 FPS
166 Kbps
12 FPS
83 Kbps
6 FPS
41 Kbps
3 FPS
14 Kbps
1 FPS
LEVEL5
288 Kbps
25 FPS
138 Kbps
12 FPS
69 Kbps
6 FPS
35 Kbps
3 FPS
12 Kbps
1 FPS
LEVEL4
230 Kbps
25 FPS
111 Kbps
12 FPS
55 Kbps
6 FPS
28 Kbps
3 FPS
9 Kbps
1 FPS
LEVEL3
173 Kbps
25 FPS
83 Kbps
12 FPS
41 Kbps
6 FPS
21 Kbps
3 FPS
7 Kbps
1 FPS
LEVEL2
115 Kbps
25 FPS
55 Kbps
12 FPS
28 Kbps
6 FPS
14 Kbps
3 FPS
5 Kbps
1 FPS
LEVEL1
58 Kbps
25 FPS
28 Kbps
12 FPS
14 Kbps
6 FPS
7 Kbps
3 FPS
2 Kbps
1 FPS
Quality
88_ appendix
TROUBLESHOOTING
PROBLEM
SOLUTION
y Check to make sure that the camera’s Network settings are appropriate.
y Check to make sure that all network cables have been connected
properly.
y If connected using DHCP, verify that the camera is able to acquire
dynamic IP addresses without any problem.
y If connected using a DDNS URL, verify that the MAC address has been
properly entered.
y If the camera is connected to a router, verify that port forwarding is
properly configured.
y Connected Viewers become disconnected upon any change to camera or
network configurations.
Viewer got disconnected during
monitoring.
y Check all network connections.
I cannot connect to the system
using a tab browser of Internet
Explorer 7.0.
y When you try to connect to the system using a tab browser, the same
cookie information is shared, resulting in errors when connected.
Therefore, instead of using a tab browser, open a new browser window
to connect to the system.
The camera connected to the
network is not detected in the IP
installer program.
y Turn off the firewall settings on your PC and then search the camera
again.
Images overlap.
y Check whether two or more cameras are set to a single multicast address
instead of different addresses. If a single address is used for multiple
cameras, the images may overlap.
No image appears.
y If the transmission method is set to multicast, check whether there is a
router that supports multicast in the LAN the camera is connected to.
y If the camera is connected over an xDSL network, it’ s possible for
Viewer to disconnect under poor network conditions.
English _89
● APPENDIX
I can’t access the camera from a
web browser.
appendix
PROBLEM
I have set &lt;Object counting&gt; to
&lt;On&gt; in &lt;Setup&gt;, but the green
box on the monitoring screen is
displayed bigger or smaller than
the image size of the passer-by.
I have set &lt;Object counting&gt; to
&lt;Enable&gt; in &lt;Setup&gt;, but the
green box is hardly displayed
or excessive on the monitoring
screen.
I couldn’t see any threshold rule
or area coefficient rule on the
monitoring screen.
SOLUTION
y Change the object size as appropriate in &lt;Setup&gt; - &lt;Object counting&gt;
on the moinitoring screen and check if the green box fits.
y If the greenbox is hardly displayed, adjust the sensitivity to higer in
&lt;Setup&gt; - &lt;Object counting&gt;; if the green box is is excessive, adjust
the sensitivity to lower in &lt;Setup&gt; - &lt;Object counting&gt;.
y Check if you have set &lt;Overlay&gt; to &lt;Enable&gt; in &lt;Setup&gt; - &lt;Object
counting&gt;.
Cannot record into the SD memory y Check if the memory card is defective.
card.
y Check if the write protection tab of the memory card is set to “Lock”.
y Check if the memory card is defective.
SD memory indicator does not
turn on even when the SD memory y Check if the &lt;Record&gt; is checked in &lt;Setup&gt; &lt;Event&gt; &lt;SD Card
card is inserted.
Record&gt; menu.
SD memory card is inserted but
the camera does not operate
properly.
Cannot format the SD memory
card.
90_ appendix
y Check if the memory card is inserted in the proper direction. Operation
of memory card that is formatted by other devices is not guaranteed
with this camera unit
y Format the memory card again in &lt;Setup&gt; &lt;Event&gt; &lt;SD Card&gt;
menu.
y Check if the write protection tab of the memory card is set to “Lock”.
GPL/LGPL SOFTWARE LICENSE
The software included in this product contains copyrighted software that is licensed under the GPL/LGPL.
You may obtain the complete Corresponding Source code from us for a period of three years after our last
shipment of this product by sending email to [email protected]
If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the
cost of physically performing source distribution might be charged.
y GPL S/W
- Base Kernel, Busybox, Sysvinit, dosfstools
y LGPL S/W
- gLibc, Inetutils
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright &copy; 1989, 1991 Free Software
Foundation, Inc.
51 Franklin Street,Fifth Floor, Boston,
MA 02110-1301, USA
Everyone is permitted to copy and
distribute verbatim copies of this license
document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take
away your freedom to share and change it. By contrast,
the GNU General Public License is intended to guarantee
your freedom to share and change free software-- to
make sure the software is free for all its users.
This General Public License applies to most of the
Free Software Foundation's software and to any other
program whose authors commit to using it. (Some
other Free Software Foundation software is covered
by the GNU Lesser General Public License instead.)
You can apply it to your programs, too.
When we speak of free software, we are referring to
freedom, not price.
Our General Public Licenses are designed to make
sure that you have the freedom to distribute copies of
free software (and charge for this service if you wish),
that you receive source code or can get it if you want
it, that you can change the software or use pieces of
it in new free programs ; and that you know you can
do these things.
To protect your rights, we need to make restrictions
that forbid anyone to deny you these rights or to
ask you to surrender the rights. These restrictions
translate to certain responsibilities for you if you
distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a
program, whether gratis or for a fee, you must give
the recipients all the rights that you have.
You must make sure that they, too, receive or can
get the source code. And you must show them these
terms so they know their rights.
We protect your rights with two steps :
(1)copyright the software, and (2)offer you this license
which gives you legal permission to copy, distribute
and/or modify the software.
Also, for each author's protection and ours, we want
to make certain that everyone understands that there
is no warranty for this free software. If the software is
modified by someone else and passed on, we want
its recipients to know that what they have is not the
original, so that any problems introduced by others
will not reflect on the original authors' reputations.
Finally, any free program is threatened constantly
by software patents. We wish to avoid the danger
that redistributors of a free program will individually
obtain patent licenses, in effect making the program
proprietary. To prevent this, we have made it clear
that any patent must be licensed for everyone's free
use or not licensed at all.
The precise terms and conditions for copying,
distribution and modification follow.
TERMS AND CONDITIONS FOR
COPYING, DISTRIBUTION AND
MODIFICATION
Version 2, June 1991 Copyright (C) 1989, 1991 Free
Software Foundation, Inc. 51 Franklin S
0. This License applies to any program or other work
which contains a notice placed by the copyright
holder saying it may be distributed under the terms
of this General Public License.
The &quot;Program&quot;, below, refers to any such
program or work, and a &quot;work based on the
Program&quot; means either the Program or any
derivative work under copyright law : that is to
say, a work containing the Program or a portion
of it, either verbatim or with modifications and/or
translated into another language. (Hereinafter,
translation is included without limitation in the term
&quot;modification&quot;.) Each licensee is addressed as
&quot;you&quot;.
Activities other than copying, distribution and
modification are not covered by this License ;
they are outside its scope. The act of running the
Program is not restricted, and the output from the
Program is covered only if its contents constitute a
work based on the Program (independent of having
been made by running the Program). Whether that
is true depends on what the Program does.
1. You may copy and distribute verbatim copies of
the Program's source code as you receive it, in
any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep
intact all the notices that refer to this License and
to the absence of any warranty ; and give any other
recipients of the Program a copy of this License
along with the Program.
You may charge a fee for the physical act of
transferring a copy, and you may at your option
offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the
Program or any portion of it, thus forming a work
based on the Program, and copy and distribute
such modifications or work under the terms of
Section 1 above, provided that you also meet all of
these conditions :
a) You must cause the modified files to carry
prominent notices stating that you changed the
files and the date of any change.
b) You must cause any work that you distribute or
publish, that in whole or in part contains or is
derived from the Program or any part thereof, to
be licensed as a whole at no charge to all third
parties under the terms of this License.
c) If the modified program normally reads
commands interactively when run,you must
cause it, when started running for such
interactive use in the most ordinary way, to
print or display an announcement including
an appropriate copyright notice and a notice
that there is no warranty (or else, saying
that you provide a warranty) and that users
may redistribute the program under these
conditions, and telling the user how to view a
copy of this License. (Exception:if the Program
itself is interactive but does not normally print
such an announcement, your work based
on the Program is not required to print an
announcement.)
These requirements apply to the modified work as
a whole. If identifiable sections of that work are not
derived from the Program, and can be reasonably
considered independent and separate works in
themselves, then this License, and its terms, do not
apply to those sections when you distribute them as
separate works. But when you distribute the same
sections as part of a whole which is a work based on
the Program, the distribution of the whole must be
on the terms of this License, whose permissions for
other licensees extend to the entire whole, and thus
to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights
or contest your rights to work written entirely by you ;
rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on
the Program. In addition, mere aggregation of another
work not based on the Program with the Program (or
with a work based on the Program)on a volume of
a storage or distribution medium does not bring the
other work under the scope of this License.
3. You may copy and distribute the Program (or a
work based on it, under Section 2)in object code
or executable form under the terms of Sections 1
and 2 above provided that you also do one of the
following :
a) Accompany it with the complete corresponding
machine-readable source code, which must
be distributed under the terms of Sections 1
and 2 above on a medium customarily used for
software interchange ; or,
b) Accompany it with a written offer, valid for at
least three years, to give any third party, for a
charge no more than your cost of physically
performing source distribution, a complete
machinereadable copy of the corresponding
source code, to be distributed under the
terms of Sections 1 and 2 above on a medium
customarily used for software interchange ; or,
c) Accompany it with the information you received
as to the offer to distribute corresponding
source code. (This alternative is allowed only
for noncommercial distribution and only if
you received the program in object code or
executable form with such an offer, in accord
with Subsection b above.)
The source code for a work means the preferred
form of the work for making modifications to it. For
an executable work, complete source code means all
the source code for all modules it contains, plus any
associated interface definition files, plus the scripts
used to control compilation and installation of the
executable. However, as a special exception, the
source code distributed need not include anything
that is normally distributed (in either source or
binary form)with the major components (compiler,
kernel, and so on)of the operating system on which
the executable runs, unless that component itself
accompanies the executable.
your obligations under this License and any other
pertinent obligations, then as a consequence you
may not distribute the Program at all.
For example, if a patent license would not permit
royalty-free redistribution of the Program by all
those who receive copies directly or indirectly
through you, then the only way you could satisfy
both it and this License would be to refrain entirely
from distribution of the Program.
If distribution of executable or object code is made
by offering access to copy from a designated place,
then offering equivalent access to copy the source
code from the same place counts as distribution of
the source code, even though third parties are not
compelled to copy the source along with the object
code.
If any portion of this section is held invalid or
unenforceable under any particular circumstance,
the balance of the section is intended to apply and
the section as a whole is intended to apply in other
circumstances. It is not the purpose of this section to
induce you to infringe any patents or other property
right claims or to contest validity of any such claims;
this section has the sole purpose of protecting the
integrity of the free software distribution system,
which is implemented by public license practices.
Many people have made generous contributions to
the wide range of software distributed through that
system in reliance on consistent application of that
system ; it is up to the author/donor to decide if he or
she is willing to distribute software through any other
system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear
what is believed to be a consequence of the rest of
this License.
4. You may not copy, modify, sublicense, or distribute
the Program except as expressly provided under
this License. Any attempt otherwise to copy,
modify, sublicense or distribute the Program is
void, and will automatically terminate your rights
under this License.
However, parties who have received copies, or
rights, from you under this License will not have
their licenses terminated so long as such parties
remain in full compliance.
5. You are not required to accept this License, since
you have not signed it.
However, nothing else grants you permission to
modify or distribute the Program or its derivative
works.
These actions are prohibited by law if you do not
accept this License.Therefore, by modifying or
distributing the Program (or any work based on
the Program), you indicate your acceptance of this
License to do so, and all its terms and conditions
for copying, distributing or modifying the Program
or works based on it.
6. Each time you redistribute the Program (or
any work based on the Program), the recipient
automatically receives a license from the original
licensor to copy, distribute or modify the Program
subject to these terms and conditions.
You may not impose any further restrictions on the
recipients' exercise of the rights granted herein.
You are not responsible for enforcing
compliance by third parties to this License.
7. If, as a consequence of a court judgment or
allegation of patent infringement or for any other
reason (not limited to patent issues), conditions
are imposed on you (whether by court order,
agreement or otherwise)that contradict the
conditions of this License, they do not excuse
you from the conditions of this License. If you
cannot distribute so as to satisfy simultaneously
8. If the distribution and/or use of the Program is
restricted in certain countries either by patents or
by copyrighted interfaces, the original copyright
holder who places the Program under this License
may add an explicit geographical distribution
limitation excluding those countries,so that
distribution is permitted only in or among countries
not thus excluded. In such case, this License
incorporates the limitation as if written in the body
of this License.
9. The Free Software Foundation may publish revised
and/or new versions of the General Public License
from time to time. Such new versions will be similar
in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number.
If the Program specifies a version number of this
License which applies to it and &quot;any later version&quot;,
you have the option of following the terms and
conditions either of that version or of any later version
published by the Free Software Foundation. If the
Program does not specify a version number of this
License, you may choose any version ever published
by the Free Software Foundation.
10. If you wish to incorporate parts of the Program
into other free programs whose distribution
conditions are different, write to the author to ask
for permission. For software which is copyrighted
by the Free Software Foundation,write to the
Free Software Foundation ; we sometimes make
exceptions for this. Our decision will be guided by
the two goals of preserving the free status of all
derivatives of our free software and of promoting
the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED
FREE OF CHARGE, THERE IS NO WARRANTY
FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM &quot;ASIS&quot;
WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE ENTIRE RISK
AS TO THE QUALITY AND PERFORMANCE OF
THE PROGRAM IS WITH YOU. SHOULD THE
PROGRAMPROVE DEFECTIVE, YOU ASSUME
THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY
APPLICABLE LAW OR AGREED TO IN WRITING
WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE DAMAGES, INCLUDING
ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT
OF THE USE OR INABILITY TO USE THE
PROGRAM (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED
INACCURATE OR LOSSES SUSTAINED BY YOU
OR THIRD PARTIES OR A FAILURE OF THE
PROGRAM TO OPERATE WITH ANY OTHER
PROGRAMS), EVEN IF SUCH HOLDER OR
OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New
Programs
If you develop a new program, and you want it to be
of the greatest possible use to the public, the best
way to achieve this is to make it free software which
everyone can redistribute and change under these
terms.
To do so, attach the following notices to the program.
It is safest to attach them to the start of each
source file to most effectively convey the exclusion
of warranty ; and each file should have at least the
&quot;copyright&quot; line and a pointer to where the full notice
is found.
one line to give the program's name and an idea of
what it does.
Copyright (C)yyyy name of author
This program is free software ; you can redistribute it
and/or modify it under the terms of the GNU General
Public License as published by the Free Software
Foundation ; either version 2 of the License, or (at
your option)any later version.
This program is distributed in the hope that it will be
useful, but WITHOUT ANY WARRANTY ; without
even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General
Public License along with this program ; if not, write
to the Free Software Foundation, Inc.,51 Franklin
Street, Fifth Floor, Boston, MA 02110-1301, USA.
Also add information on how to contact you by
electronic and paper mail. If the program is interactive,
make it output a short notice like this when it starts in
an interactive mode :
Gnomovision version 69,
Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO
WARRANTY ; for details type ‘show w’. This is free
software, and you are welcome to redistribute it under
certain conditions ; type ‘show c’ for details.
The hypothetical commands ‘show w’ and ‘show
c’ should show the appropriate parts of the General
Public License. Of course, the commands you use
may be called something other than ‘show w’ and
‘show c’ ; they could even be mouse-clicks or menu
items-- whatever suits your program.
You should also get your employer (if you work
as a programmer)or your school, if any, to sign a
&quot;copyright disclaimer&quot; for the program,if necessary.
Here is a sample ; alter the names:
Yoyodyne, Inc.,hereby disclaims all copyright interest
in the program ‘Gnomovision’ (which makes passes
at compilers) written by James Hacker.
signature of Ty Coon, 1 April 1989 Ty Coon, President
of Vice This General Public License does not permit
incorporating your program into proprietary programs.
If your program is a subroutine library, you may
consider it more useful to permit linking proprietary
applications with the library. If this is what you want
to do, use the GNU Lesser General Public License
instead of this License.
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright &copy; 2007 Free Software Foundation, Inc.
&lt;http://fsf.org/&gt;
Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed.
Preamble
The GNU General Public License is a free, copyleft
license for software and other kinds of works. The
licenses for most software and other practical works
are designed to take away your freedom to share
and change the works. By contrast, the GNU General
Public License is intended to guarantee your freedom
to share and change all versions of a program--to
make sure it remains free software for all its users.
We, the Free Software Foundation, use the GNU
General Public License for most of our software; it
applies also to any other work released this way by its
authors.
You can apply it to your programs, too.
When we speak of free software, we are referring to
freedom, not price. Our General Public Licenses are
designed to make sure that you have the freedom
to distribute copies of free software (and charge for
them if you wish), that you receive source code or can
get it if you want it, that you can change the software
or use pieces of it in new free programs, and that you
know you can do these things.
To protect your rights, we need to prevent others
from denying you these rights or asking you to
surrender the rights. Therefore, you have certain
responsibilities if you distribute copies of the software,
or if you modify it: responsibilities to respect the
freedom of others.
For example, if you distribute copies of such a
program, whether gratis or for a fee, you must pass
on to the recipients the same freedoms that you
received. You must make sure that they, too, receive
or can get the source code. And you must show
them these terms so they know their rights.
Developers that use the GNU GPL protect your rights
with two steps: (1) assert copyright on the software,
and (2) offer you this License giving you legal
permission to copy, distribute and/or modify it.
For the developers' and authors' protection, the GPL
clearly explains that there is no warranty for this free
software. For both users' and authors' sake, the
GPL requires that modified versions be marked as
changed, so that their problems will not be attributed
erroneously to authors of previous versions.
Some devices are designed to deny users access
to install or run modified versions of the software
inside them, although the manufacturer can do so.
This is fundamentally incompatible with the aim of
protecting users' freedom to change the software.
The systematic pattern of such abuse occurs in
the area of products for individuals to use, which is
precisely where it is most unacceptable. Therefore,
we have designed this version of the GPL to prohibit
the practice for those products. If such problems
arise substantially in other domains, we stand ready
to extend this provision to those domains in future
versions of the GPL, as needed to protect the
freedom of users.
Finally, every program is threatened constantly by
software patents. States should not allow patents to
restrict development and use of software on generalpurpose computers, but in those that do, we wish
to avoid the special danger that patents applied to a
free program could make it effectively proprietary. To
prevent this, the GPL assures that patents cannot be
used to render the program non-free.
The precise terms and conditions for copying,
distribution and modification follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General
Public License.
“Copyright” also means copyright-like laws that apply
to other kinds of works, such as semiconductor
masks.
“The Program” refers to any copyrightable work
licensed under this License. Each licensee is
addressed as “you”. “Licensees” and “recipients” may
be individuals or organizations.
To “modify” a work means to copy from or adapt all
or part of the work in a fashion requiring copyright
permission, other than the making of an exact copy.
The resulting work is called a “modified version” of the
earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified
Program or a work based on the Program.
To “propagate” a work means to do anything with it
that, without permission, would make you directly or
secondarily liable for infringement under applicable
copyright law, except executing it on a computer
or modifying a private copy. Propagation includes
copying, distribution (with or without modification),
making available to the public, and in some countries
other activities as well.
shared libraries and dynamically linked subprograms
that the work is specifically designed to require, such
as by intimate data communication or control flow
between those subprograms and other parts of the
work.
To “convey” a work means any kind of propagation
that enables other parties to make or receive copies.
Mere interaction with a user through a computer
network, with no transfer of a copy, is not conveying.
The Corresponding Source need not include anything
that users can regenerate automatically from other
parts of the Corresponding Source.
An interactive user interface displays “Appropriate
Legal Notices” to the extent that it includes a
convenient and prominently visible feature that (1)
displays an appropriate copyright notice, and (2) tells
the user that there is no warranty for the work (except
to the extent that warranties are provided), that
licensees may convey the work under this License,
and how to view a copy of this License. If the
interface presents a list of user commands or options,
such as a menu, a prominent item in the list meets
this criterion.
1. Source Code.
The “source code” for a work means the preferred
form of the work for making modifications to it. “Object
code” means any non-source form of a work.
A “Standard Interface” means an interface that
either is an official standard defined by a recognized
standards body, or, in the case of interfaces specified
for a particular programming language, one that
is widely used among developers working in that
language.
The “System Libraries” of an executable work include
anything, other than the work as a whole, that (a) is
included in the normal form of packaging a Major
Component, but which is not part of that Major
Component, and (b) serves only to enable use of the
work with that Major Component, or to implement
a Standard Interface for which an implementation is
available to the public in source code form. A “Major
Component”, in this context, means a major essential
component (kernel, window system, and so on) of
the specific operating system (if any) on which the
executable work runs, or a compiler used to produce
the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code
form means all the source code needed to generate,
install, and (for an executable work) run the object
code and to modify the work, including scripts to
control those activities. However, it does not include
the work's System Libraries, or general-purpose tools
or generally available free programs which are used
unmodified in performing those activities but which
are not part of the work. For example, Corresponding
Source includes interface definition files associated
with source files for the work, and the source code for
The Corresponding Source for a work in source code
form is that same work.
2. Basic Permissions.
All rights granted under this License are granted
for the term of copyright on the Program, and are
irrevocable provided the stated conditions are
met. This License explicitly affirms your unlimited
permission to run the unmodified Program. The
output from running a covered work is covered
by this License only if the output, given its
content, constitutes a covered work. This License
acknowledges your rights of fair use or other
equivalent, as provided by copyright law.
You may make, run and propagate covered works
that you do not convey, without conditions so long
as your license otherwise remains in force. You may
convey covered works to others for the sole purpose
of having them make modifications exclusively for
you, or provide you with facilities for running those
works, provided that you comply with the terms of
this License in conveying all material for which you do
not control copyright. Those thus making or running
the covered works for you must do so exclusively
on your behalf, under your direction and control, on
terms that prohibit them from making any copies of
your copyrighted material outside their relationship
with you.
Conveying under any other circumstances is
permitted solely under the conditions stated below.
Sublicensing is not allowed; section 10 makes it
unnecessary.
3. Protecting Users' Legal Rights From AntiCircumvention Law.
No covered work shall be deemed part of an effective
technological measure under any applicable law
fulfilling obligations under article 11 of the WIPO
copyright treaty adopted on 20 December 1996, or
similar laws prohibiting or restricting circumvention of
such measures.
When you convey a covered work, you waive any
legal power to forbid circumvention of technological
measures to the extent such circumvention is effected
by exercising rights under this License with respect
to the covered work, and you disclaim any intention
to limit operation or modification of the work as a
means of enforcing, against the work's users, your
or third parties' legal rights to forbid circumvention of
technological measures.
work in an aggregate does not cause this License to
apply to the other parts of the aggregate.
6. Conveying Non-Source Forms.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program's
source code as you receive it, in any medium,
provided that you conspicuously and appropriately
publish on each copy an appropriate copyright
notice; keep intact all notices stating that this License
and any non-permissive terms added in accord with
section 7 apply to the code; keep intact all notices of
the absence of any warranty; and give all recipients a
copy of this License along with the Program.
You may charge any price or no price for each
copy that you convey, and you may offer support or
warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or
the modifications to produce it from the Program, in
the form of source code under the terms of section 4,
provided that you also meet all of these conditions:
a) The work must carry prominent notices stating
that you modified it, and giving a relevant date.
b) The work must carry prominent notices stating
that it is released under this License and
any conditions added under section 7. This
requirement modifies the requirement in section
4 to “keep intact all notices”.
c) You must license the entire work, as a whole,
under this License to anyone who comes into
possession of a copy. This License will therefore
apply, along with any applicable section 7
additional terms, to the whole of the work,
and all its parts, regardless of how they are
packaged. This License gives no permission
to license the work in any other way, but it
does not invalidate such permission if you have
separately received it.
d) If the work has interactive user interfaces,
each must display Appropriate Legal Notices;
however, if the Program has interactive
interfaces that do not display Appropriate Legal
Notices, your work need not make them do so.
A compilation of a covered work with other separate
and independent works, which are not by their nature
extensions of the covered work, and which are not
combined with it such as to form a larger program, in
or on a volume of a storage or distribution medium,
is called an “aggregate” if the compilation and its
resulting copyright are not used to limit the access or
legal rights of the compilation's users beyond what
the individual works permit. Inclusion of a covered
You may convey a covered work in object code form
under the terms of sections 4 and 5, provided that
you also convey the machine-readable Corresponding
Source under the terms of this License, in one of
these ways:
a) Convey the object code in, or embodied in, a
physical product (including a physical distribution
medium), accompanied by the Corresponding
Source fixed on a durable physical medium
customarily used for software interchange.
b) Convey the object code in, or embodied
in, a physical product (including a physical
distribution medium), accompanied by a written
offer, valid for at least three years and valid for
as long as you offer spare parts or customer
support for that product model, to give anyone
who possesses the object code either (1) a
copy of the Corresponding Source for all the
software in the product that is covered by
this License, on a durable physical medium
customarily used for software interchange, for
a price no more than your reasonable cost of
physically performing this conveying of source,
or (2) access to copy the Corresponding Source
from a network server at no charge.
c) Convey individual copies of the object code
with a copy of the written offer to provide
the corresponding Source. This alternative is
allowed only occasionally and noncommercially,
and only if you received the object code with
such an offer, in accord with subsection 6b.
d) Convey the object code by offering access from
a designated place (gratis or for a charge), and
offer equivalent access to the Corresponding
Source in the same way through the same
place at no further charge. You need not require
recipients to copy the Corresponding Source
along with the object code. If the place to
copy the object code is a network server, the
Corresponding Source may be on a different
server (operated by you or a third party) that
supports equivalent copying facilities, provided
you maintain clear directions next to the object
code saying where to find the Corresponding
Source. Regardless of what server hosts the
Corresponding Source, you remain obligated to
ensure that it is available for as long as needed
to satisfy these requirements.
e) Convey the object code using peer-to-peer
transmission, provided you inform other peers
where the object code and Corresponding
Source of the work are being offered to the
general public at no charge under subsection 6d.
A separable portion of the object code, whose source
code is excluded from the Corresponding Source as
a System Library, need not be included in conveying
the object code work.
A “User Product” is either (1) a “consumer product”,
which means any tangible personal property which
is normally used for personal, family, or household
purposes, or (2) anything designed or sold for
incorporation into a dwelling. In determining whether
a product is a consumer product, doubtful cases
shall be resolved in favor of coverage. For a particular
product received by a particular user, “normally used”
refers to a typical or common use of that class of
product, regardless of the status of the particular
user or of the way in which the particular user actually
uses, or expects or is expected to use, the product. A
product is a consumer product regardless of whether
the product has substantial commercial, industrial or
non-consumer uses, unless such uses represent the
only significant mode of use of the product.
“Installation Information” for a User Product means
any methods, procedures, authorization keys, or
other information required to install and execute
modified versions of a covered work in that User
Product from a modified version of its Corresponding
Source. The information must suffice to ensure that
the continued functioning of the modified object
code is in no case prevented or interfered with solely
because modification has been made.
If you convey an object code work under this section
in, or with, or specifically for use in, a User Product,
and the conveying occurs as part of a transaction
in which the right of possession and use of the User
Product is transferred to the recipient in perpetuity or
for a fixed term (regardless of how the transaction is
characterized), the Corresponding Source conveyed
under this section must be accompanied by the
Installation Information. But this requirement does
not apply if neither you nor any third party retains
the ability to install modified object code on the User
Product (for example, the work has been installed in
ROM).
The requirement to provide Installation Information
does not include a requirement to continue to provide
support service, warranty, or updates for a work that
has been modified or installed by the recipient, or for
the User Product in which it has been modified or
installed. Access to a network may be denied when
the modification itself materially and adversely affects
the operation of the network or violates the rules and
protocols for communication across the network.
Corresponding Source conveyed, and Installation
Information provided, in accord with this section must
be in a format that is publicly documented (and with
an implementation available to the public in source
code form), and must require no special password or
key for unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement
the terms of this License by making exceptions from
one or more of its conditions. Additional permissions
that are applicable to the entire Program shall be
treated as though they were included in this License,
to the extent that they are valid under applicable law.
If additional permissions apply only to part of the
Program, that part may be used separately under
those permissions, but the entire Program remains
governed by this License without regard to the
additional permissions.
When you convey a copy of a covered work, you may
at your option remove any additional permissions
from that copy, or from any part of it. (Additional
permissions may be written to require their own
removal in certain cases when you modify the work.)
You may place additional permissions on material,
added by you to a covered work, for which you have
or can give appropriate copyright permission.
Notwithstanding any other provision of this License,
for material you add to a covered work, you may (if
authorized by the copyright holders of that material)
supplement the terms of this License with terms:
a) Disclaiming warranty or limiting liability differently
from the terms of sections 15 and 16 of this
License; or
b) Requiring preservation of specified reasonable
legal notices or author attributions in that
material or in the Appropriate Legal Notices
displayed by works containing it; or
c) Prohibiting misrepresentation of the origin of
that material, or requiring that modified versions
of such material be marked in reasonable ways
as different from the original version; or
d) Limiting the use for publicity purposes of names
of licensors or authors of the material; or
e) Declining to grant rights under trademark law
for use of some trade names, trademarks, or
service marks; or
f) Requiring indemnification of licensors and
authors of that material by anyone who conveys
the material (or modified versions of it) with
contractual assumptions of liability to the
recipient, for any liability that these contractual
assumptions directly impose on those licensors
and authors.
All other non-permissive additional terms are considered
“further restrictions” within the meaning of section
10. If the Program as you received it, or any part of
it, contains a notice stating that it is governed by this
License along with a term that is a further restriction,
you may remove that term. If a license document
contains a further restriction but permits relicensing
or conveying under this License, you may add to a
covered work material governed by the terms of that
license document, provided that the further restriction
does not survive such relicensing or conveying.
If you add terms to a covered work in accord with
this section, you must place, in the relevant source
files, a statement of the additional terms that apply
to those files, or a notice indicating where to find the
applicable terms.
Additional terms, permissive or non-permissive, may
be stated in the form of a separately written license,
or stated as exceptions; the above requirements
apply either way.
8. Termination.
You may not propagate or modify a covered work
except as expressly provided under this License. Any
attempt otherwise to propagate or modify it is void,
and will automatically terminate your rights under this
License (including any patent licenses granted under
the third paragraph of section 11).
However, if you cease all violation of this License,
then your license from a particular copyright holder
is reinstated (a) provisionally, unless and until the
copyright holder explicitly and finally terminates your
license, and (b) permanently, if the copyright holder
fails to notify you of the violation by some reasonable
means prior to 60 days after the cessation.
Moreover, your license from a particular copyright
holder is reinstated permanently if the copyright
holder notifies you of the violation by some reasonable
means, this is the first time you have received notice
of violation of this License (for any work) from that
copyright holder, and you cure the violation prior to
30 days after your receipt of the notice.
Termination of your rights under this section does not
terminate the licenses of parties who have received
copies or rights from you under this License. If your
rights have been terminated and not permanently
reinstated, you do not qualify to receive new licenses
for the same material under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order
to receive or run a copy of the Program. Ancillary
propagation of a covered work occurring solely as a
consequence of using peer-to-peer transmission to
receive a copy likewise does not require acceptance.
However, nothing other than this License grants you
permission to propagate or modify any covered work.
These actions infringe copyright if you do not accept
this License. Therefore, by modifying or propagating
a covered work, you indicate your acceptance of this
License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient
automatically receives a license from the original
licensors, to run, modify and propagate that work,
subject to this License. You are not responsible
for enforcing compliance by third parties with this
License.
An “entity transaction” is a transaction transferring
control of an organization, or substantially all assets
of one, or subdividing an organization, or merging
organizations. If propagation of a covered work
results from an entity transaction, each party to that
transaction who receives a copy of the work also
receives whatever licenses to the work the party's
predecessor in interest had or could give under
the previous paragraph, plus a right to possession
of the Corresponding Source of the work from the
predecessor in interest, if the predecessor has it or
can get it with reasonable efforts.
You may not impose any further restrictions on the
exercise of the rights granted or affirmed under this
License. For example, you may not impose a license
fee, royalty, or other charge for exercise of rights
granted under this License, and you may not initiate
litigation (including a cross-claim or counterclaim in a
lawsuit) alleging that any patent claim is infringed by
making, using, selling, offering for sale, or importing
the Program or any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes
use under this License of the Program or a work on
which the Program is based. The work thus licensed
is called the contributor's “contributor version”.
A contributor's “essential patent claims” are all
patent claims owned or controlled by the contributor,
whether already acquired or hereafter acquired,
that would be infringed by some manner, permitted
by this License, of making, using, or selling its
contributor version, but do not include claims that
would be infringed only as a consequence of further
modification of the contributor version. For purposes
of this definition, “control” includes the right to grant
patent sublicenses in a manner consistent with the
requirements of this License.
Each contributor grants you a non-exclusive,
worldwide, royalty-free patent license under the
contributor's essential patent claims, to make, use,
sell, offer for sale, import and otherwise run, modify
and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license”
is any express agreement or commitment, however
denominated, not to enforce a patent (such as an
express permission to practice a patent or covenant
not to sue for patent infringement). To “grant” such
a patent license to a party means to make such an
agreement or commitment not to enforce a patent
against the party.
If you convey a covered work, knowingly relying on
a patent license, and the Corresponding Source of
the work is not available for anyone to copy, free of
charge and under the terms of this License, through
a publicly available network server or other readily
accessible means, then you must either (1) cause
the Corresponding Source to be so available, or
(2) arrange to deprive yourself of the benefit of the
patent license for this particular work, or (3) arrange,
in a manner consistent with the requirements of this
License, to extend the patent license to downstream
recipients. “Knowingly relying” means you have
actual knowledge that, but for the patent license,
your conveying the covered work in a country, or
your recipient's use of the covered work in a country,
would infringe one or more identifiable patents in that
country that you have reason to believe are valid.
If, pursuant to or in connection with a single
transaction or arrangement, you convey, or propagate
by procuring conveyance of, a covered work, and
grant a patent license to some of the parties receiving
the covered work authorizing them to use, propagate,
modify or convey a specific copy of the covered work,
then the patent license you grant is automatically
extended to all recipients of the covered work and
works based on it.
A patent license is “discriminatory” if it does not
include within the scope of its coverage, prohibits the
exercise of, or is conditioned on the non-exercise of
one or more of the rights that are specifically granted
under this License. You may not convey a covered
work if you are a party to an arrangement with a third
party that is in the business of distributing software,
under which you make payment to the third party
based on the extent of your activity of conveying the
work, and under which the third party grants, to any
of the parties who would receive the covered work
from you, a discriminatory patent license
(a) in connection with copies of the covered work
conveyed by you (or copies made from those
copies), or
(b) primarily for and in connection with specific
products or compilations that contain the
covered work, unless you entered into that
arrangement, or that patent license was
granted, prior to 28 March 2007.
Nothing in this License shall be construed as
excluding or limiting any implied license or other
defenses to infringement that may otherwise be
available to you under applicable patent law.
12. No Surrender of Others' Freedom.
If conditions are imposed on you (whether by court
order, agreement or otherwise) that contradict the
conditions of this License, they do not excuse you
from the conditions of this License. If you cannot
convey a covered work so as to satisfy simultaneously
your obligations under this License and any other
pertinent obligations, then as a consequence you
may not convey it at all. For example, if you agree to
terms that obligate you to collect a royalty for further
conveying from those to whom you convey the
Program, the only way you could satisfy both those
terms and this License would be to refrain entirely
from conveying the Program.
13. Use with the GNU Affero General Public
License.
Notwithstanding any other provision of this License,
you have permission to link or combine any covered
work with a work licensed under version 3 of the GNU
Affero General Public License into a single combined
work, and to convey the resulting work. The terms of
this License will continue to apply to the part which
is the covered work, but the special requirements of
the GNU Affero General Public License, section 13,
concerning interaction through a network will apply to
the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised
and/ or new versions of the GNU General Public
License from time to time. Such new versions will be
similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number.
If the Program specifies that a certain numbered
version of the GNU General Public License “or any
later version” applies to it, you have the option of
following the terms and conditions either of that
numbered version or of any later version published by
the Free Software Foundation. If the Program does
not specify a version number of the GNU General
Public License, you may choose any version ever
published by the Free Software Foundation.
If the Program specifies that a proxy can decide
which future versions of the GNU General Public
License can be used, that proxy's public statement of
acceptance of a version permanently authorizes you
to choose that version for the Program.
Later license versions may give you additional
or different permissions. However, no additional
obligations are imposed on any author or copyright
holder as a result of your choosing to follow a later
version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM,
TO THE EXTENT PERMITTED BY APPLICABLE LAW.
EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESSED
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD THE PROGRAM PROVE DEFECTIVE,
YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY
WHO MODIFIES AND/OR CONVEYS THE PROGRAM
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE
THE PROGRAM (INCLUDING BUT NOT LIMITED
TO LOSS OF DATA OR DATA BEING RENDERED
INACCURATE OR LOSSES SUSTAINED BY YOU OR
THIRD PARTIES OR A FAILURE OF THE PROGRAM
TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
USA Everyone is permitted to copy and distribute
verbatim copies of this license document, but
changing it is not allowed.
[This is the first released version of the Lesser GPL.
It also counts as the successor of the GNU Library
Public License, version 2, hence the version number
2.1.]
Preamble
The licenses for most software are designed to
take away your freedom to share and change it.
By contrast, the GNU General Public Licenses are
intended to guarantee your freedom to share and
change free software to make sure the software is
free for all its users.
This license, the Lesser General Public License,
applies to some specially designated software
packages-typically libraries-of the Free Software
Foundation and other authors who decide to use it.
You can use it too, but we suggest you first think
carefully about whether this license or the ordinary
General Public License is the better strategy to use in
any particular case, based on the explanations below.
When we speak of free software, we are referring
to freedom of use, not price. Our General Public
Licenses are designed to make sure that you have
the freedom to distribute copies of free software (and
charge for this service if you wish); that you receive
source code or can get it if you want it; that you can
change the software and use pieces of it in new free
programs; and that you are informed that you can do
these things.
To protect your rights, we need to make restrictions
that forbid distributors to deny you these rights or to
ask you to surrender these rights. These restrictions
translate to certain responsibilities for you if you
distribute copies of the library or if you modify it.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability
provided above cannot be given local legal effect
according to their terms, reviewing courts shall apply
local law that most closely approximates an absolute
waiver of all civil liability in connection with the
Program, unless a warranty or assumption of liability
accompanies a copy of the Program in return for a fee.
END OF TERMS AND CONDITIONS
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright &copy; 1991, 1999 Free Software Foundation,
Inc. 51 Franklin Street, Fifth Floor, Boston, MA
02110-1301
For example, if you distribute copies of the library,
whether gratis or for a fee, you must give the
recipients all the rights that we gave you. You must
make sure that they, too, receive or can get the
source code. If you link other code with the library,
you must provide complete object files to the
recipients, so that they can relink them with the library
after making changes to the library and recompiling it.
And you must show them these terms so they know
their rights.
We protect your rights with a two-step method: (1)
we copyright the library, and (2) we offer you this
license, which gives you legal permission to copy,
distribute and/or modify the library.
To protect each distributor, we want to make it very
clear that there is no warranty for the free library. Also,
if the library is modified by someone else and passed
on, the recipients should know that what they have is
not the original version, so that the original author’s
reputation will not be affected by problems that might
be introduced by others.
Although the Lesser General Public License is Less
protective of the users’ freedom, it does ensure that
the user of a program that is linked with the Library
has the freedom and the wherewithal to run that
program using a modified version of the Library.
Finally, software patents pose a constant threat to the
existence of any free program. We wish to make sure
that a company cannot effectively restrict the users of
a free program by obtaining a restrictive license from
a patent holder. Therefore, we insist that any patent
license obtained for a version of the library must be
consistent with the full freedom of use specified in this
license.
The precise terms and conditions for copying,
distribution and modification follow. Pay close
attention to the difference between a “work based
on the library” and a “work that uses the library”.
The former contains code derived from the library,
whereas the latter must be combined with the library
in order to run.
Most GNU software, including some libraries, is
covered by the ordinary GNU General Public License.
This license, the GNU Lesser General Public License,
applies to certain designated libraries, and is quite
different from the ordinary General Public License. We
use this license for certain libraries in order to permit
linking those libraries into non-free programs.
When a program is linked with a library, whether
statically or using a shared library, the combination
of the two is legally speaking a combined work, a
derivative of the original library. The ordinary General
Public License therefore permits such linking only
if the entire combination fits its criteria of freedom.
The Lesser General Public License permits more lax
criteria for linking other code with the library.
We call this license the “Lesser” General Public
License because it does Less to protect the user’
s freedom than the ordinary General Public License.
It also provides other free software developers Less
of an advantage over competing non-free programs.
These disadvantages are the reason we use the
ordinary General Public License for many libraries.
However, the Lesser license provides advantages in
certain special circumstances.
For example, on rare occasions, there may be a
special need to encourage the widest possible use
of a certain library, so that it becomes a de-facto
standard. To achieve this, non-free programs must
be allowed to use the library. A more frequent case is
that a free library does the same job as widely used
non-free libraries. In this case, there is little to gain by
limiting the free library to free software only, so we
use the Lesser General Public License.
In other cases, permission to use a particular library
in non-free programs enables a greater number of
people to use a large body of free software. For
example, permission to use the GNU C Library in
non-free programs enables many more people to
use the whole GNU operating system, as well as its
variant, the GNU/ Linux operating system.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software
library or other program which contains a notice
placed by the copyright holder or other authorized
party saying it may be distributed under the terms
of this Lesser General Public License (also called
“this License”). Each licensee is addressed as
“you”.
A “library” means a collection of software functions
and/ or data prepared so as to be conveniently linked
with application programs (which use some of those
functions and data) to form executables.
The “Library”, below, refers to any such software
library or work which has been distributed under
these terms. A “work based on the Library” means
either the Library or any derivative work under
copyright law: that is to say, a work containing the
Library or a portion of it, either verbatim or with
modifications and/or translated straightforwardly into
another language. (Hereinafter, translation is included
without limitation in the term
“modification”.)
“Source code” for a work means the preferred form of
the work for making modifications to it. For a library,
complete source code means all the source code for
all modules it contains, plus any associated interface
definition files, plus the scripts used to control
compilation and installation of the library.
Activities other than copying, distribution and
modification are not covered by this License; they are
outside its scope. The act of running a program using
the Library is not restricted, and output from such a
program is covered only if its contents constitute a
work based on the Library (independent of the use
of the Library in a tool for writing it). Whether that is
true depends on what the Library does and what the
program that uses the Library does.
1. You may copy and distribute verbatim copies of the
Library’s complete source code as you receive it, in
any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep
intact all the notices that refer to this License and
to the absence of any warranty; and distribute a
copy of this License along with the Library.
You may charge a fee for the physical act of
transferring a copy, and you may at your option offer
warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library
or any portion of it, thus forming a work based
on the Library, and copy and distribute such
modifications or work under the terms of Section
1 above, provided that you also meet all of these
conditions:
a) The modified work must itself be a software
library. b) You must cause the files modified
to carry prominent notices stating that you
changed the files and the date of any change.
c) You must cause the whole of the work to be
licensed at no charge to all third parties under
the terms of this License. d) If a facility in the
modified Library refers to a function or a table of
data to be supplied by an application program
that uses the facility, other than as an argument
passed when the facility is invoked, then you
must make a good faith effort to ensure that, in
the event an application does not supply such
function or table, the facility still operates, and
performs whatever part of its purpose remains
meaningful. (For example, a function in a library
to compute square roots has a purpose that
is entirely well-defined independent of the
application. Therefore, Subsection 2d requires
that any application-supplied function or table
used by this function must be optional: if the
application does not supply it, the square root
function must still compute square roots.) These
requirements apply to the modified work as a
whole. If identifiable sections of that work are not
derived from the Library, and can be reasonably
considered independent and separate works
in themselves, then this License, and its terms,
do not apply to those sections when you
distribute them as separate works. But when
you distribute the same sections as part of a
whole which is a work based on the Library, the
distribution of the whole must be on the terms
of this License, whose permissions for other
licensees extend to the entire whole, and thus to
each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights
or contest your rights to work written entirely by you;
rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on
the Library.
In addition, mere aggregation of another work not
based on the Library with the Library (or with a work
based on the Library) on a volume of a storage or
distribution medium does not bring the other work
under the scope of this License.
3. You may opt to apply the terms of the ordinary
GNU General Public License instead of this License
to a given copy of the Library. To do this, you must
alter all the notices that refer to this License, so
that they refer to the ordinary GNU General Public
License, version 2, instead of to this License. (If a
newer version than version 2 of the ordinary GNU
General Public License has appeared, then you
can specify that version instead if you wish.) Do not
make any other change in these notices.
Once this change is made in a given copy, it is
irreversible for that copy, so the ordinary GNU General
Public License applies to all subsequent copies and
derivative works made from that copy.
This option is useful when you wish to copy part of
the code of the Library into a program that is not a
library.
4. You may copy and distribute the Library (or a
portion or derivative of it, under Section 2) in
object code or executable form under the terms
of Sections 1 and 2 above provided t hat you
accompany it with the complete corresponding
machine-readable source code, which must be
distributed under the terms of Sections 1 and 2
above on a medium customarily used for software
interchange.
If distribution of object code is made by offering
access to copy from a designated place, then offering
equivalent access to copy the source code from the
same place satisfies the requirement to distribute
the source code, even though third parties are not
compelled to copy the source along with the object
code.
5. A program that contains no derivative of any
portion of the Library, but is designed to work
with the Library by being compiled or linked with
it, is called a “work that uses the Library”. Such a
work, in isolation, is not a derivative work of the
Library, and therefore falls outside the scope of this
License.
However, linking a “work that uses the Library” with
the Library creates an executable that is a derivative
of the Library (because it contains portions of the
Library), rather than a “work that uses the library”.
The executable is therefore covered by this License.
Section 6 states terms for distribution of such
executables.
When a “work that uses the Library” uses material
from a header file that is part of the Library, the
object code for the work may be a derivative work
of the Library even though the source code is not.
Whether this is true is especially significant if the work
can be linked without the Library, or if the work is
itself a library. The threshold for this to be true is not
precisely defined by law.
If such an object file uses only numerical parameters,
data structure layouts and accessors, and small
macros and small inline functions (ten lines or less in
length), then the use of the object file is unrestricted,
regardless of whether it is legally a derivative work.
(Executables containing this object code plus portions
of the Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library,
you may distribute the object code for the work under
the terms of Section 6. Any executables containing
that work also fall under Section 6, whether or not
they are linked directly with the Library itself.
6. As an exception to the Sections above, you may
also combine or link a “work that uses the Library”
with the Library to produce a work containing
portions of the Library, and distribute that work
under terms of your choice, provided that the terms
permit modification of the work for the customer’
s own use and reverse engineering for debugging
such modifications.
You must give prominent notice with each copy of
the work that the Library is used in it and that the
Library and its use are covered by this License.
You must supply a copy of this License. If the work
during execution displays copyright notices, you must
include the copyright notice for the Library among
them, as well as a reference directing the user to the
copy of this License. Also, you must do one of these
things:
a) Accompany the work with the complete
corresponding machine-readable source code
for the Library including whatever changes were
used in the work (which must be distributed
under Sections 1 and 2 above); and, if the work
is an executable linked with the Library, with the
complete machine readable “work that uses the
Library”, as object code and/or source code,
so that the user can modify the Library and
then relink to produce a modified executable
containing the modified Library. (It is understood
that the user who changes the contents of
definitions files in the Library will not necessarily
be able to recompile the application to use the
modified definitions.)
b) Use a suitable shared library mechanism for
linking with the Library. A suitable mechanism is
one that
(1) uses at run time a copy of the library already
present on the user’s computer system, rather
than copying library functions into the executable,
and (2) will operate properly with a modified version
of the library, if the user installs one, as long as the
modified version is interface-compatible with the
version that the work was made with.
c) Accompany the work with a written offer,
valid for at least three years, to give the same
user the materials specified in Subsection 6a,
above, for a charge no more than the cost of
performing this distribution.
d) If distribution of the work is made by offering
access to copy from a designated place, offer
equivalent access to copy the above specified
materials from the same place.
e) Verify that the user has already received a copy
of these materials or that you have already sent
this user a copy.
For an executable, the required form of the “work that
uses the Library” must include any data and utility
programs needed for reproducing the executable
from it. However, as a special exception, the materials
to be distributed need not include anything that is
normally distributed (in either source or binary form)
with the major components (compiler, kernel, and so
on) of the operating system on which the executable
runs, unless that component itself accompanies the
executable.
It may happen that this requirement contradicts the
license restrictions of other proprietary libraries that
do not normally accompany the operating system.
Such a contradiction means you cannot use both
them and the Library together in an executable that
you distribute.
7. You may place library facilities that are a work
based on the Library side-by-side in a single library
together with other library facilities not covered
by this License, and distribute such a combined
library, provided that the separate distribution of the
work based on the Library and of the other library
facilities is otherwise permitted, and provided that
you do these two things:
a) Accompany the combined library with a
copy of the same work based on the Library,
uncombined with any other library facilities.
This must be distributed under the terms of the
Sections above.
b) Give prominent notice with the combined library
of the fact that part of it is a work based on
the Library, and explaining where to find the
accompanying uncombined form of the same
work.
8. You may not copy, modify, sublicense, link with, or
distribute the Library except as expressly provided
under this License. Any attempt otherwise to copy,
modify, sublicense, link with, or distribute the
Library is void, and will automatically terminate your
rights under this License. However, parties who
have received copies, or rights, from you under this
License will not have their licenses terminated so
long as such parties remain in full compliance.
9. You are not required to accept this License, since
you have not signed it. However, nothing else
grants you permission to modify or distribute the
Library or its derivative works. These actions are
prohibited by law if you do not accept this License.
Therefore, by modifying or distributing the Library
(or any work based on the Library), you indicate
your acceptance of this License to do so, and all
its terms and conditions for copying, distributing or
modifying the Library or works based on it.
10. Each time you redistribute the Library (or
any work based on the Library), the recipient
automatically receives a license from the original
licensor to copy, distribute, link with or modify the
Library subject to these terms and conditions.
You may not impose any further restrictions on
the recipients’
exercise of the rights granted herein. You are not
responsible for enforcing compliance by third
parties with this License.
11. If, as a consequence of a court judgment or
allegation of patent infringement or for any other
reason (not limited to patent issues), conditions
are imposed on you (whether by court order,
agreement or otherwise) that contradict the
conditions of this License, they do not excuse
you from the conditions of this License. If you
cannot distribute so as to satisfy simultaneously
your obligations under this License and any other
pertinent obligations, then as a consequence you
may not distribute the Library at all. For example,
if a patent license would not permit royalty free
redistribution of the Library by all those who
receive copies directly or indirectly through you,
then the only way you could satisfy both it and
this License would be to refrain entirely from
distribution of the Library.
If any portion of this section is held invalid or
unenforceable under any particular circumstance,
the balance of the section is intended to apply, and
the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or
to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free
software distribution system which is implemented
by public license practices. Many people have
made generous contributions to the wide range of
software distributed through that system in reliance
on consistent application of that system; it is up to
the author/donor to decide if he or she is willing to
distribute software through any other system and a
licensee cannot impose that choice.
This section is intended to make thoroughly clear
what is believed to be a consequence of the rest of
this License.
12. If the distribution and/or use of the Library is
restricted in certain countries either by patents
or by copyrighted interfaces, the original
copyright holder who places the Library under
this License may add an explicit geographical
distribution limitation excluding those countries,
so that distribution is permitted only in or among
countries not thus excluded. In such case, this
License incorporates the limitation as if written in
the body of this License.
13. The Free Software Foundation may publish
revised and/or new versions of the Lesser General
Public License from time to time. Such new versions
will be similar in spirit to the present version, but may
differ in detail to address new problems or concerns.
Each version is given a distinguishing version number.
If the Library specifies a version number of this
License which applies to it and “any later version”,
you have the option of following the terms and
conditions either of that version or of any later version
published by the Free Software Foundation. If the
Library does not specify a license version number,
you may choose any version ever published by the
Free Software Foundation.
14. If you wish to incorporate parts of the Library into
other free programs whose distribution conditions
are incompatible with these, write to the author
to ask for permission. For software which is
copyrighted by the Free Software Foundation,
write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision
will be guided by the two goals of preserving the
free status of all derivatives of our free software
and of promoting the sharing and reuse of
software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE
OF CHARGE, THERE IS NO WARRANTY FOR
THE LIBRARY, TO THE EXTENT PERMITTED
BY APPLICABLE LAW. EXCEPT WHEN
OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE LIBRARY “AS IS”
WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE ENTIRE RISK AS
TO THE QUALITY AND PERFORMANCE OF THE
LIBRARY IS WITH YOU. SHOULD THE LIBRARY
PROVE DEFECTIVE, YOU ASSUME THE COST
OF ALL NECESSARY SERVICING, REPAIR OR
CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY
APPLICABLE LAW OR AGREED TO IN
WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MAY MODIFY
AND/OR REDISTRIBUTE THE LIBRARY AS
PERMITTED ABOVE, BE LIABLE TO YOU
FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE LIBRARY (INCLUDING
BUT NOT LIMITED TO LOSS OF DATA OR DATA
BEING RENDERED INACCURATE OR LOSSES
SUSTAINED BY YOU OR THIRD PARTIES OR
A FAILURE OF THE LIBRARY TO OPERATE
WITH ANY OTHER SOFTWARE), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New
Libraries
If you develop a new library, and you want it to
be of the greatest possible use to the public, we
recommend making it free software that everyone can
redistribute and change. You can do so by permitting
redistribution under these terms (or, alternatively,
under the terms of the ordinary General Public
License).
To apply these terms, attach the following notices
to the library. It is safest to attach them to the start
of each source file to most effectively convey the
exclusion of warranty; and each file should have at
least the “copyright” line and a pointer to where the
full notice is found. one line to give the library’s name
and an idea of what it does.
Copyright &copy; year name of author
This library is free software; you can redistribute
it and/ or modify it under the terms of the GNU
Lesser General Public License as published by the
Free Software Foundation; either version 2.1 of the
License, or (at your option) any later version.
This library is distributed in the hope that it will be
useful, but WITHOUT ANY WARRANTY; without
even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the
GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser
General Public License along with this library; if
not, write to the Free Software Foundation, Inc., 51
Franklin Street, Fifth Floor, Boston, MA 02110-1301
USA Also add information on how to contact you by
electronic and paper mail.
You should also get your employer (if you work
as a programmer) or your school, if any, to sign a
“copyright disclaimer” for the library, if necessary.
Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest
in the library ‘Frob’ (a library for tweaking knobs)
written by James Random Hacker.
signature of Ty Coon, 1 April 1990 Ty Coon, President
of Vice.
OpenSSL LICENSE
Copyright &copy; 1998-2006 The OpenSSL Project. All
rights reserved. Redistribution and use in source and
binary forms, with or without modification, are permitted
provided that the following conditions are met:
1. Redistributions of source code must retain the
above copyright notice, this list of conditions and
the following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and
the following disclaimer in the documentation and/
or other materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgment: “This product includes software
developed by the OpenSSL Project for use in the
OpenSSL Toolkit. (http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and
“OpenSSL Project” must not be used to endorse or
promote products derived from this software without
prior written permission. For written permission,
please contact [email protected].
5. Products derived from this software may not be
called “OpenSSL” nor may
“OpenSSL” appear in their names without prior
written permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain
the following acknowledgment: “This product includes
software developed by the OpenSSL Project for use
in the OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL
PROJECT “AS IS” AND ANY EXPRESSED OR
IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE OpenSSL PROJECT OR ITS
CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE. This product
includes cryptographic software written by Eric Young
([email protected]). This product includes software
written by Tim Hudson([email protected]).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.
com) All rights reserved. This package is an SSL
implementation written by Eric Young (eay@cryptsoft.
com). The implementation was written so as to
conform with Netscapes SSL. This library is free for
commercial and non-commercial use as long as the
following conditions are aheared to. The following
conditions apply to all code found in this distribution,
be it the RC4, RSA, lhash, DES, etc., code; not just
the SSL code. The SSL documentation included with
this distribution is covered by the same copyright
terms except that the holder is Tim Hudson (tjh@
cryptsoft.com).
Copyright remains Eric Young’s, and as such any
Copyright notices in the code are not to be removed.
If this package is used in a product, Eric Young
should be given attribution as the author of the parts
of the library used. This can be in the form of a textual
message at program startup or in documentation
(online or textual) provided with the package.
Redistribution and use in source and binary forms,
with or without modification, are permitted provided
that the following conditions are met:
1. Redistributions of source code must retain the
copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and
the following disclaimer in the documentation and/
or other materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgement: “This product includes
cryptographic software written by Eric Young (eay@
cryptsoft.com)” The word ‘cryptographic’
can be left out if the rouines from the library being
used are not cryptographic related :-).
4. If you include any Windows specific code (or
a derivative thereof) from the apps directory
(application code) you must include an
acknowledgement: “This product includes software
written by Tim Hudson (tjh@ cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC
YOUNG ‘‘AS IS AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR
OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for any publically
available version or derivative of this code cannot be
changed. i.e. this code cannot simply be copied and
put under another distribution licence [including the
GNU Public Licence.
Samsung Techwin cares for the environment at all product manufacturing stages, and is
taking measures to provide customers with more environmentally friendly products.
The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly
products, and indicates that the product satisfies the EU RoHS Directive.
Correct Disposal of This Product (Waste Electrical &amp; Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic
accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste
at the end of their working life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take these items for environmentally safe
recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product and its electronic accessories should not be mixed with other commercial wastes
for disposal.
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&amp;D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : +1-877-213-1222 FAX : +1-310-632-2195
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
www.samsungipolis.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
">

Hello! I am an AI chatbot specifically trained to assist you with the Samsung Techwin SND-3080CF network camera User Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated