Hitachi CP-X3010EN Technical Appendix

Hitachi CP-X3010EN Technical Appendix
CTRL001 PROJECTOR CONTROL UNIT
The CTRL001 is a wall mounted easy to use projector control unit compatible with all current and the majority
of Hitachi legacy projectors. The CTRL001 offers manual and automatic on/off and source selection functions.
The auto on function is activated when a USB lead connected to a PC is plugged in to the unit, as the USB
signal can be passed through to an external device; this makes the unit ideal for incorporation in to an
interactive whiteboard setup.
An additional USB connector is incorporated for connecting USB devices to the attached PC. This allows the
user to access files stored on their USB or memory device with the interactive whiteboard setup, without the
need to access the PC.
When connected to a PC the unit is powered by the USB port but will revert to battery power when the PC is
disconnected. The unit incorporates intelligent battery saving technology with a lifetime of at least 6 months.
Power and error indicators are included to alert the user of low battery and other fault conditions.
Custom units can be produced with up to 7 buttons for large orders, minimum quantities and prices on application.
Key Features:
• Turns projector on or off
• Instant Off/On
• Change Input Source
• Warning lights
• No need for a remote control
• Preserves battery life (batteries not included)
• USB Port so that presentations or homework
can be uploaded onto a whiteboard with ease
• Supplied with 5m RS232 cable
CTRL001
Technical specifications
Operation
The unit will remain in unpowered state until either power is detected
on USB input or on/off button is pressed
• On USB power detect
Retrieve last selected channel from non-volatile memory and send
power-on command to projector followed by channel select command.
• On USB power down
Start timeout.
RJ45 socket
USB type A socket
• On power button press when powered down
Retrieve last selected channel from non-volatile memory and send
power on command to projector followed by channel select
command. Start timeout.
• On power button press when powered up
Send command to projector to turn off. Disconnect power.
• On channel button press when powered down
Retrieve last selected channel from non-volatile memory and send
power on command to projector followed by channel select
command. Start timeout.
• On channel button press when powered up
Step to next channel, save channel number in non-volatile memory
and send channel command to projector. Start timeout.
USB type A socket
USB type B socket
• On ten second timeout
Disconnect battery power.
CONNECTORS
USB type B socket
USB type A socket
RJ45 socket
USB type A socket
to PC/laptop
to whiteboard
RS232 to projector
for USB memory stick
on bottom of board
on bottom of board
on top of board
on top of board
Momentary contact push button
Momentary contact push button
Power ON/OFF. Automatic power OFF after 10 seconds if no USB power.
Select next channel
Green LED
Red LED
Illuminated when USB power detected or push button pressed
Flash briefly every 5 seconds when battery is low.
Flash three times quickly if communication with projector fails
SWITCHES
ON/OFF
CHANNEL
INDICATORS
ON
ERROR
LINKS
1 link jumper
3 further jumper links on pcb
To force manual only operation
For future enhancements
BATTERY
Holder for 2/4 AA cells
Provision for further inputs and indicators on pcb
At least 6 months life
DIMENSIONS
Dimensions (H x W x D)
Weight
130 x 67 x 30mm
150g
HITACHI DIGITAL MEDIA, Hitachi Europe Ltd, Whitebrook Park, Lower Cookham Road, Maidenhead, Berkshire SL6 8YA UNITED KINGDOM
Tel: +44 (0)1628 585 000 Fax: +44 (0)1628 585 500 www.hitachidigitalmedia.com
The specification above and photography is for reference only and may be subject to change.
07/08
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement