3M X65 Technical Appendix
X65
Multimedia Projector
Operator’s Guide TECHNICAL
In this section, the technical information about this projector is described.
WARNING Before using, read the "User's Manual - Safety Guide" and these
manuals to ensure correct usage through understanding. After reading, store
them in a safe place for future reference.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual.
• The reproduction, transmission or use of this document or contents is not permitted without
express written authority.
TRADEMARK ACKNOWLEDGEMENT:
• VGA and XGA are registered trademarks of the International Business Machines Corporation.
• Apple and Mac are registered trademarks of Apple Computer, Inc.
• VESA and SVGA are trademarks of the Video Electronics Standard Association.
• Windows is a registered trademark of Microsoft Corporation.
All other trademarks are the property of their respective owners.
TECHNICAL
Dimension Diagram
RGB OUT
AUDIO 1
IN
AUDIO
IN
2
R
AUDIO OUT
L
CONTROL
USB
S-VIDEO IN
VIDEO IN
1
CR/PR CB/PB
COMPONENT VIDEO
Y
RGB IN
2
DVI
266
256.5
360
62.8
106
112.5
49.7
108.4
Unit : mm
Signal Connector Pin Assignment
1. D-sub 15-pin Shrink Connector (RGB IN 1/RGB IN 2/RGB OUT)
Pin No
1
2
3
4
5
6
7
8
Signal
Video input Red
Video input Green
Video input Blue
Ground
Ground Red
Ground Green
Ground Blue
Pin No
Signal
9
10
11
-
12
13
14
Ground
Pin No
15
RGB IN 1: SDA(DDC)
RGB IN 2: RGB OUT: H. sync./ Composite sync.
Vertical sync
Signal
RGB IN 1: SCL(DDC)
RGB IN 2: RGB OUT: -
5 4 3 2 1
10 9 8 7 6
15 14 13 12 11
2. Digital Receptacle Connector (DVI)
Pin No
1
2
3
4
5
6
7
8
9
10
Signal
T.M.D.S. Data 2 T.M.D.S. Data 2 +
T.M.D.S. Data 2 / 4 Shield
DDC Clock
DDC Data
Analog V. Sync.
T.M.D.S. Data 1 T.M.D.S. Data 1 +
Pin No
Signal
11
12
13
14
15
16
17
18
19
20
T.M.D.S. Data 1 / 3 Shield
+5V Power
Ground (+5V, Analog H/V Sync.)
Hot-Plug Sense
T.M.D.S. Data 0 T.M.D.S. Data 0 +
T.M.D.S. Data 0 / 5 Shield
-
Pin No
21
22
23
24
Signal
T.M.D.S. Clock Shield
T.M.D.S. Clock +
T.M.D.S. Clock -
1 2 3 4
5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
3. Mini Din 4-pin Connector (S-VIDEO)
Signal
1
Color:0.286Vp-p (NTSC, burst signal),75Ω terminator
0.300Vp-p (PAL/SECAM, burst signal),75Ω terminator
2
Brightness:1.0Vp-p, 75Ω terminator
3
Ground
4
Ground
TECHNICAL
Pin No
TECHNICAL - 2
TECHNICAL (continued)
Example of computer signal
Resolution
H×V
fH (kHz)
fV (Hz)
Rating
Signal mode
Display mode
640 × 350
37.9
85.1
VESA
VGA-1
Zoom in
640 × 400
37.9
85.1
VESA
VGA-2
Zoom in
720 × 400
37.9
85.0
VESA
TEXT
Zoom in
640 × 480
31.5
59.9
VESA
640 × 480
35.0
66.7
640 × 480
37.9
72.8
640 × 480
37.5
640 × 480
43.3
800 × 600
800 × 600
VGA (60Hz)
Zoom in
Mac13"mode
Zoom in
VESA
VGA (72Hz)
Zoom in
75.0
VESA
VGA (75Hz)
Zoom in
85.0
VESA
VGA (85Hz)
Zoom in
35.2
56.3
VESA
SVGA (56Hz)
Zoom in
37.9
60.3
VESA
SVGA (60Hz)
Zoom in
800 × 600
48.1
72.2
VESA
SVGA (72Hz)
Zoom in
800 × 600
46.9
75.0
VESA
SVGA (75Hz)
Zoom in
800 × 600
53.7
85.1
VESA
SVGA (85Hz)
Zoom in
832 × 624
49.7
74.5
1024 × 768
48.4
60.0
VESA
XGA (60Hz)
1024 × 768
56.5
70.1
VESA
XGA (70Hz)
1024 × 768
60.0
75.0
VESA
XGA (75Hz)
1024 × 768
68.7
85.0
VESA
XGA (85Hz)
1152 × 864
67.5
75.0
VESA
SXGA (75Hz)
Zoom out
1280 × 960
60.0
60.0
VESA
SXGA (60Hz)
Zoom out
1280 × 1024
64.0
60.0
VESA
SXGA (60Hz)
Zoom out
1280 × 1024
80.0
75.0
VESA
SXGA (75Hz)
Zoom out
Mac16"mode
NOTE • Some computers may have multiple display screen modes. Use of some of these modes
will not be possible with this projector.
• Be sure to check jack type, signal level, timing and resolution before connecting this projector to a
computer.
• Depending on the input signal, full-size display may not be possible in some cases. Refer to the
number of display pixels above.
• The image may not be displayed correctly when the input sync. signal is "Composite Sync." or
"Sync. on G".
• The image might be something wrong with computer by computer on the DVI mode. In this case, it
is recommended to reduce the resolution and / or reflesh rate.
TECHNICAL - 3
TECHNICAL (continued)
Initial set signals
The following signals are used for the initial settings.
The signal timing of some computer models may be different. In such case, refer to adjust the
V.POSIT and H.POSIT of the menu.
Back porch b
Front porch d
Display interval c
Back porch b
Front porch d
Display interval c
DATA
DATA
HSYNC
VSYNC
Sync a
Computer /
Signal
Sync a
Horizontal signal timing (µs)
Computer /
Signal
Vertical signal timimg (lines)
VGA-1 (85Hz)
a
2.0
b
3.0
c
20.3
d
1.0
VGA-1 (85Hz)
a
3
b
60
c
350
d
32
VGA-2 (85Hz)
2.0
3.0
20.3
1.0
VGA-2 (85Hz)
3
41
400
1
TEXT
2.0
3.0
20.3
1.0
TEXT
3
42
480
1
VGA (60Hz)
3.8
1.9
25.4
0.6
VGA (60Hz)
2
33
480
10
Mac 13"mode
2.1
3.2
21.2
2.1
Mac 13"mode
3
39
480
3
VGA (72Hz)
1.3
3.8
20.3
1.0
VGA (72Hz)
3
28
480
9
VGA (75Hz)
2.0
3.8
20.3
0.5
VGA (75Hz)
3
16
480
1
VGA (85Hz)
1.6
2.2
17.8
1.6
VGA (85Hz)
3
25
480
1
SVGA (56Hz)
2.0
3.6
22.2
0.7
SVGA (56Hz)
2
22
600
1
SVGA (60Hz)
3.2
2.2
20.0
1.0
SVGA (60Hz)
4
23
600
1
SVGA (72Hz)
2.4
1.3
16.0
1.1
SVGA (72Hz)
6
23
600
37
SVGA (75Hz)
1.6
3.2
16.2
0.3
SVGA (75Hz)
3
21
600
1
SVGA (85Hz)
1.1
2.7
14.2
0.6
SVGA (85Hz)
3
27
600
1
Mac 16"mode
1.1
3.9
14.5
0.6
Mac 16"mode
3
39
624
1
XGA (60Hz)
2.1
2.5
15.8
0.4
XGA (60Hz)
6
29
768
3
XGA (70Hz)
1.8
1.9
13.7
0.3
XGA (70Hz)
6
29
768
3
XGA (75Hz)
1.2
2.2
13.0
0.2
XGA (75Hz)
3
28
768
1
1.0
2.2
10.8
0.5
XGA (85Hz)
3
36
768
1
1.2
2.4
10.7
0.6
1152×864 (75Hz)
3
32
864
1
1280×960 (60Hz)
1.0
2.9
11.9
0.9
1280×960 (60Hz)
3
36
960
1
1280×1024 (60Hz)
1.0
2.3
11.9
0.4
1280×1024 (60Hz)
3
38
1024
1
1280×1024 (75Hz)
1.1
1.8
9.5
0.1
1280×1024 (75Hz)
3
38
1024
1
TECHNICAL
XGA (85Hz)
1152×864 (75Hz)
TECHNICAL - 4
TECHNICAL (continued)
Connection to the Mouse Control
1. PS/2, ADB or Serial Mouse
(1) Turn off the projector and computer, and connect the two units with the appropriate cable. For
PS/2 mouse control (for IBM and compatible), use the enclosed mouse cable. For others, consult
your dealer.
(2) Disconnect the USB cable from the projector if it is connected. Then turn on the projector.
(3) Turn on the computer.
(4) Start the mouse function. If the mouse has not been started, reboot the computer (soft reboot or
reboot buttons). Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT button” of page 4.
2. USB Mouse
(1) Connect the projector and computer with a suitable commercially available USB cable. Consult
your dealer to get the cable, if you need.
(2) Start the mouse function. Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT
button” of page 4.
NOTE • Before connecting, read the instruction manuals of the devices to be connected.
• In the case of notebook type computers with an internal pointing device, the mouse control
function will not work unless the internal pointing device is disabled. In such case, disable the
internal pointing device and change the BIOS setting to select an external mouse before the
operations described in (1) to (4) above.
Also, some computers may not have a utility program to operate a mouse.
Refer to the computer hardware manual for detail.
PS/2 Mouse
Projector
CONTROL Terminal
CLK
DATA
D-sub 15-pin shrink jack
6
2 3 4 5
7 8 9 10
11 12 13 14 15
1
SEL0
RTS
+5V
GND
TECHNICAL - 5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Computer
1
2
3
4
5
6
DATA
GND
+5V
CLK
Mouse jack
Mini DIN 6-pin
6
5
3
4
2
1
TECHNICAL (continued)
ADB Mouse
Projector
CONTROL Terminal
DATA
D-sub 15-pin shrink jack
6
2 3 4 5
7 8 9 10
11 12 13 14 15
1
RTS
+5V
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Computer
1 ADB
2 (POWER ON)
3 +5V
4 GND
Mouse jack
Mini DIN 4-pin
3
4
1
2
Serial Mouse
CONTROL Terminal
D-sub 15-pin shrink jack
6
2 3 4 5
7 8 9 10
11 12 13 14 15
1
Projector
1
2
3
4
5
SEL0 6
RTS 7
8
9
GND 10
11
12
13
TD 14
15
1
2
3
4
5
6
7
8
9
Computer
CD
RD
TD
DTR
GND
DSR
RTS
CTS
RI
Mouse jack
D-sub 9-pin
1
2
6
3
7
5
4
8
9
USB Mouse
2
3
1
4
Computer
Projector
+5V 1
1
+5V
—DATA 2
2 —DATA
+DATA 3
3
GND 4
USB jack
(A type)
+DATA
4 GND
1
2
3
4
USB cable
TECHNICAL - 6
TECHNICAL
USB jack
(B type)
TECHNICAL (continued)
RS-232C communication
(1) Turn off the projector and computer power supplies and connect with the RS-232C cable.
(2) Turn on the computer power supply and after the computer has started up, turn on the projector
power supply.
Projector
Control jack
D-sub 15-pin shrink jack
5 4 3 2 1
10 9 8 7 6
15 14 13 12 11
Computer
1
2
3
4
5
SELO 6
RTS 7
8
9
GND 10
11
12
RD 13
TD 14
15
1
2
3
4
5
6
7
8
9
CD
RD
TD
DTR
GND
DSR
RTS
CTS
RI
RS-232C jack
D-sub 9-pin
2
1
6
3
7
4
8
Communications setting
19200bps, 8N1
1 Protocol
Consist of header (7 bytes) + command data (6 bytes).
2 Header
BE + EF + 03 + 06 + 00 + CRC_low + CRC_high
CRC_low : Lower byte of CRC flag for command data.
CRC_high : Upper byte of CRC flag for command data.
3 Command data
Command data chart
byte_0
byte_1
byte_2
Action
low
byte_3
Type
high
low
byte_4
byte_5
Setting code
high
low
high
Action (byte_0 - 1)
Action
Classification
Content
1
SET
Change setting to desired value.
2
GET
Read projector internal setup value.
4
INCREMENT
Increment setup value by 1.
5
DECREMENT
Decrement setup value by 1.
6
EXECUTE
Run a command.
TECHNICAL - 7
5
9
TECHNICAL (continued)
Requesting projector status (Get command)
(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’)
from the computer to the projector.
(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
Changing the projector settings (Set command)
(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) + setting code (2
bytes)) from the computer to the projector.
(2) The projector changes the setting based on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Using the projector default settings (Reset Command)
(1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+ type (2
bytes) +‘00H’+‘00H’) to the projector.
(2) The projector changes the specified setting to the default value.
(3) The projector returns the response code ‘06H’ to the computer.
Increasing the projector setting value (Increment command)
(1) The computer sends the increment code Header + Command data (‘04H’+‘00H’+ type (2 bytes)
+‘00H’+‘00H’) to the projector.
(2) The projector in creases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Decreasing the projector setting value (Decrement command)
(1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+ type (2 bytes)
+‘00H’ + ‘00H’) to the projector.
(2) The projector decreases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
When the projector cannot understand the received command
When the projector cannot understand the received command, the error code ‘15H’ is sent back to
the computer. Some times, the computer cannot properly receive the command. In such a case, the
command is not executed and the error code ‘15H’ is sent back to the computer. If the this error
code is returned, send the same command again.
When the projector cannot execute the received command
NOTE • Operation cannot be guaranteed when the projector receives an undefined command or
data.
• Provide an interval of at least 40ms between the response code and any other code.
• The projector outputs test data when the power supply is switched ON, and when the lamp is lit.
Ignore this data.
• Commands are not accepted during warm-up.
TECHNICAL - 8
TECHNICAL
When the projector cannot execute the received command, the the error code ‘1cH’ +‘xxxxH’ is
sent back to the computer.
When the data length is greater than indicated by the data length code, the projector will ignore the
excess data code. Conversely, when the data length is shorter than indicated by the data length code,
an error code will be returned to the omputer.
TECHNICAL (continued)
Command data chart
Names
Blank Color
Mirror
Operation type
Set
Set
Type
Setting code
Red
BE EF
03
06 00
3B D3
01 00
00 30
00 00
Orange
BE EF
03
06 00
AB D2
01 00
00 30
01 00
Green
BE EF
03
06 00
5B D2
01 00
00 30
02 00
Blue
BE EF
03
06 00
CB D3
01 00
00 30
03 00
Purple
BE EF
03
06 00
FB D1
01 00
00 30
04 00
White
BE EF
03
06 00
6B D0
01 00
00 30
05 00
Black
BE EF
03
06 00
9B D0
01 00
00 30
06 00
MyScreen
BE EF
03
06 00
FB CA
01 00
00 30
20 00
ORIGNAL
BE EF
03
06 00
FB E2
01 00
00 30
40 00
Get
BE EF
03
06 00
08 D3
02 00
00 30
00 00
Normal
BE EF
03
06 00
C7 D2
01 00
01 30
00 00
H Inverse
BE EF
03
06 00
57 D3
01 00
01 30
01 00
V lnverse
BE EF
03
06 00
A7 D3
01 00
01 30
02 00
H&V Inverse
BE EF
03
06 00
37 D2
01 00
01 30
03 00
BE EF
03
06 00
F4 D2
02 00
01 30
00 00
Normal
BE EF
03
06 00
83 D2
01 00
02 30
00 00
Freeze
BE EF
03
06 00
13 D3
01 00
02 30
01 00
BE EF
03
06 00
B0 D2
02 00
02 30
00 00
Red
BE EF
03
06 00
7F D3
01 00
03 30
00 00
Orange
BE EF
03
06 00
EF D2
01 00
03 30
01 00
Green
BE EF
03
06 00
1F D2
01 00
03 30
02 00
Blue
BE EF
03
06 00
8F D3
01 00
03 30
03 00
Purple
BE EF
03
06 00
BF D1
01 00
03 30
04 00
Transparent
BE EF
03
06 00
2F D0
01 00
03 30
05 00
Gray
BE EF
03
06 00
DF D0
01 00
03 30
06 00
Get
BE EF
03
06 00
4C D3
02 00
03 30
00 00
ORIGNAL
BE EF
03
06 00
0B D2
01 00
04 30
00 00
OFF
BE EF
03
06 00
9B D3
01 00
04 30
01 00
MyScreen
BE EF
03
06 00
CB CB
01 00
04 30
20 00
Get
BE EF
03
06 00
38 D2
02 00
04 30
00 00
Get
Freeze
Set
Get
Menu Color
Startup
Language
Set
Set
Set
TECHNICAL - 9
Command data
Header
CRC
Action
English
BE EF
03
06 00
F7 D3
01 00
05 30
00 00
Français
BE EF
03
06 00
67 D2
01 00
05 30
01 00
Deutsch
BE EF
03
06 00
97 D2
01 00
05 30
02 00
Español
BE EF
03
06 00
07 D3
01 00
05 30
03 00
Italiano
BE EF
03
06 00
37 D1
01 00
05 30
04 00
Norsk
BE EF
03
06 00
A7 D0
01 00
05 30
05 00
Nederlands
BE EF
03
06 00
57 D0
01 00
05 30
06 00
Português
BE EF
03
06 00
C7 D1
01 00
05 30
07 00
Chinese
BE EF
03
06 00
37 D4
01 00
05 30
08 00
Get
BE EF
03
06 00
C4 D3
02 00
05 30
00 00
TECHNICAL (continued)
Command data chart
Operation type
Command data
Header
Type
Setting code
Get
BE EF
03
06 00
7C D2
02 00
07 30
00 00
Increment
BE EF
03
06 00
1A D2
04 00
07 30
00 00
Decrement
BE EF
03
06 00
CB D3
05 00
07 30
00 00
Get
BE EF
03
06 00
08 86
02 00
10 31
00 00
Increment
BE EF
03
06 00
6E 86
04 00
10 31
00 00
Decrement
BE EF
03
06 00
BF 87
05 00
10 31
00 00
Brightness Reset
Execute
BE EF
03
06 00
58 D3
06 00
00 70
00 00
Contrast Reset
Execute
BE EF
03
06 00
A4 D2
06 00
01 70
00 00
V.Position Reset
Execute
BE EF
03
06 00
E0 D2
06 00
02 70
00 00
H.Position Reset
Execute
BE EF
03
06 00
IC D3
06 00
03 70
00 00
H.Size Reset
Execute
BE EF
03
06 00
68 D2
06 00
04 70
00 00
Color Balance R Reset
Execute
BE EF
03
06 00
94 D3
06 00
05 70
00 00
Color Balance B Reset
Execute
BE EF
03
06 00
D0 D3
06 00
06 70
00 00
Sharpness Reset
Execute
BE EF
03
06 00
C4 D0
06 00
09 70
00 00
Color Reset
Execute
BE EF
03
06 00
80 D0
06 00
0A 70
00 00
Tint Reset
Execute
BE EF
03
06 00
7C D1
06 00
0B 70
00 00
Keystone_V Reset
Execute
BE EF
03
06 00
08 D0
06 00
0C 70
00 00
Keystone_H Reset
Execute
BE EF
03
06 00
98 D8
06 00
20 70
00 00
Auto
Execute
BE EF
03
06 00
91 D0
06 00
0A 20
00 00
off
BE EF
03
06 00
FB D8
01 00
20 30
00 00
on
BE EF
03
06 00
6B D9
01 00
20 30
01 00
BE EF
03
06 00
C8 D8
02 00
20 30
00 00
BE EF
03
06 00
D9 D8
02 00
20 60
00 00
Magnify
Auto off
Blank on/off
Set
Get
Error Status
Get
(Example of Return)
00 00
01 00
(Normal) (Cover-error)
04 00
(Temp-error)
Power
Set
Volume
Set
Action
02 00
(Fan-error)
05 00
(Air flow-error)
03 00
(Lamp-error)
06 00
(Lamp-Time-over)
BE EF
BE EF
BE EF
03
03
03
06 00
06 00
06 00
2A D3
BA D2
19 D3
01 00
01 00
02 00
00 60
00 60
00 60
00 00
01 00
00 00
RGB1
BE EF
03
06 00
FE D2
01 00
00 20
00 00
RGB2
BE EF
03
06 00
3E D0
01 00
00 20
04 00
DVI
BE EF
03
06 00
0E D2
01 00
00 20
03 00
Video
BE EF
03
06 00
6E D3
01 00
00 20
01 00
SVideo
BE EF
03
06 00
9E D3
01 00
00 20
02 00
Component
OFF
ON
Get
Input Source
CRC
BE EF
03
06 00
AE D1
01 00
00 20
05 00
Get
BE EF
03
06 00
CD D2
02 00
00 20
00 00
Get
BE EF
03
06 00
31 D3
02 00
01 20
00 00
Increment
BE EF
03
06 00
57 D3
04 00
01 20
00 00
Decrement
BE EF
03
06 00
86 D2
05 00
01 20
00 00
TECHNICAL - 10
TECHNICAL
Names
TECHNICAL (continued)
Command data chart
Names
Operation type
Command data
Header
CRC
Mute
Brightness
Contrast
Color
Balance R
Color
Balance B
Keystone_V
Keystone_H
Aspect
Type
Setting code
Normal
BE EF
03
06 00
46 D3
01 00
02 20
00 00
Mute
BE EF
03
06 00
D6 D2
01 00
02 20
01 00
Get
BE EF
03
06 00
75 D3
02 00
02 20
00 00
Get
BE EF
03
06 00
89 D2
02 00
03 20
00 00
Increment
BE EF
03
06 00
EF D2
04 00
03 20
00 00
Decrement
BE EF
03
06 00
3E D3
05 00
03 20
00 00
Get
BE EF
03
06 00
FD D3
02 00
04 20
00 00
Increment
BE EF
03
06 00
9B D3
04 00
04 20
00 00
Decrement
BE EF
03
06 00
4A D2
05 00
04 20
00 00
Get
BE EF
03
06 00
01 D2
02 00
05 20
00 00
Increment
BE EF
03
06 00
67 D2
04 00
05 20
00 00
Decrement
BE EF
03
06 00
B6 D3
05 00
05 20
00 00
Get
BE EF
03
06 00
45 D2
02 00
06 20
00 00
Increment
BE EF
03
06 00
23 D2
04 00
06 20
00 00
Decrement
BE EF
03
06 00
F2 D3
05 00
06 20
00 00
Get
BE EF
03
06 00
B9 D3
02 00
07 20
00 00
Increment
BE EF
03
06 00
DF D3
04 00
07 20
00 00
Decrement
BE EF
03
06 00
0E D2
05 00
07 20
00 00
Get
BE EF
03
06 00
E9 D0
02 00
0B 20
00 00
Increment
BE EF
03
06 00
8F D0
04 00
0B 20
00 00
Decrement
Set
BE EF
03
06 00
5E D1
05 00
0B 20
00 00
4:3, Full
BE EF
03
06 00
9E D0
01 00
08 20
00 00
16:9
BE EF
03
06 00
0E D1
01 00
08 20
01 00
Small
BE EF
03
06 00
FE D1
01 00
08 20
02 00
BE EF
03
06 00
AD D0
02 00
08 20
00 00
Default
BE EF
03
06 00
62 D1
01 00
09 20
00 00
Bottom
BE EF
03
06 00
F2 D0
01 00
09 20
01 00
Top
BE EF
03
06 00
02 D0
01 00
09 20
02 00
Get
BE EF
03
06 00
51 D1
02 00
09 20
00 00
Get
BE EF
03
06 00
0D 83
02 00
00 21
00 00
Increment
BE EF
03
06 00
6B 83
04 00
00 21
00 00
Decrement
BE EF
03
06 00
BA 82
05 00
00 21
00 00
Get
BE EF
03
06 00
F1 82
02 00
01 21
00 00
Increment
BE EF
03
06 00
97 82
04 00
01 21
00 00
Decrement
BE EF
03
06 00
46 83
05 00
01 21
00 00
Get
BE EF
03
06 00
B5 82
02 00
02 21
00 00
Increment
BE EF
03
06 00
D3 82
04 00
02 21
00 00
Decrement
BE EF
03
06 00
02 83
05 00
02 21
00 00
Get
BE EF
03
06 00
49 83
02 00
03 21
00 00
Increment
BE EF
03
06 00
2F 83
04 00
03 21
00 00
Decrement
BE EF
03
06 00
FE 82
05 00
03 21
00 00
Set
Get
Display
Position at
16 : 9 or Small
V.Position
H.Position
H.Size
H.Phase
Action
Set
TECHNICAL - 11
TECHNICAL (continued)
Command data chart
Names
Operation type
Sharpness
Color
Tint
Set
Video Format
Type
Setting code
Get
BE EF
03
06 00
F1 72
02 00
01 22
00 00
Increment
BE EF
03
06 00
97 72
04 00
01 22
00 00
Decrement
BE EF
03
06 00
46 73
05 00
01 22
00 00
Get
BE EF
03
06 00
B5 72
02 00
02 22
00 00
Increment
BE EF
03
06 00
D3 72
04 00
02 22
00 00
Decrement
BE EF
03
06 00
02 73
05 00
02 22
00 00
Get
BE EF
03
06 00
49 73
02 00
03 22
00 00
Increment
BE EF
03
06 00
2F 73
04 00
03 22
00 00
Decrement
BE EF
03
06 00
FE 72
05 00
03 22
00 00
Auto
BE EF
03
06 00
9E 75
01 00
00 22
0A 00
NTSC
BE EF
03
06 00
FE 71
01 00
00 22
04 00
PAL
BE EF
03
06 00
6E 70
01 00
00 22
05 00
SECAM
BE EF
03
06 00
6E 75
01 00
00 22
09 00
NTSC 4.43
BE EF
03
06 00
5E 72
01 00
00 22
02 00
M-PAL
BE EF
03
06 00
FE 74
01 00
00 22
08 00
N-PAL
BE EF
03
06 00
0E 71
01 00
00 22
07 00
BE EF
03
06 00
0D 73
02 00
00 22
00 00
1080i
BE EF
03
06 00
F2 73
01 00
05 22
00 00
1035i
BE EF
03
06 00
62 72
01 00
05 22
01 00
Get
HDTV
CRC
Action
Set
Get
PinP Size
Command data
Header
Set
Set
PinP Position
BE EF
03
06 00
C1 73
02 00
05 22
00 00
off
BE EF
03
06 00
FE 22
01 00
00 23
00 00
Large
BE EF
03
06 00
6E 23
01 00
00 23
01 00
Small
BE EF
03
06 00
9E 23
01 00
00 23
02 00
Get
BE EF
03
06 00
CD 22
02 00
00 23
00 00
Upper left
BE EF
03
06 00
02 23
01 00
01 23
00 00
Upper right
BE EF
03
06 00
92 22
01 00
01 23
01 00
bottom left
BE EF
03
06 00
62 22
01 00
01 23
03 00
bottom right
BE EF
03
06 00
F2 23
01 00
01 23
02 00
BE EF
03
06 00
31 23
02 00
01 23
00 00
RGB
BE EF
03
06 00
BA 22
01 00
03 23
00 00
Video
BE EF
03
06 00
2A 23
01 00
03 23
01 00
BE EF
03
06 00
89 22
02 00
03 23
00 00
Video
BE EF
03
06 00
D6 22
01 00
02 23
01 00
S-Video
BE EF
03
06 00
26 22
01 00
02 23
02 00
Get
BE EF
03
06 00
75 23
02 00
02 23
00 00
Get
Get
Set
PinP Input
TECHNICAL - 12
TECHNICAL
Set
PinP Audio ch
TECHNICAL (continued)
Command data chart
Names
Sync on G
WHISPER
GAMMA
IR Remote Front
Operation type
CRC
Action
Type
Setting code
off
BE EF
03
06 00
CB D0
01 00
08 30
01 00
on
BE EF
03
06 00
5B D1
01 00
08 30
00 00
Get
BE EF
03
06 00
68 D1
02 00
08 30
00 00
Set
NORMAL
BE EF
03
06 00
3B 23
01 00
00 33
00 00
WHISPER
BE EF
03
06 00
AB 22
01 00
00 33
01 00
Get
BE EF
03
06 00
08 23
02 00
00 33
00 00
NORMAL
BE EF
03
06 00
C7 F0
01 00
A1 30
00 00
CINEMA
BE EF
03
06 00
57 F1
01 00
A1 30
01 00
DYNAMIC
BE EF
03
06 00
A7 F1
01 00
A1 30
02 00
Get
BE EF
03
06 00
F4 F0
02 00
A1 30
00 00
off
BE EF
03
06 00
FF 32
01 00
00 26
00 00
on
BE EF
03
06 00
6F 33
01 00
00 26
01 00
BE EF
03
06 00
CC 32
02 00
00 26
00 00
off
BE EF
03
06 00
03 33
01 00
01 26
00 00
on
BE EF
03
06 00
93 32
01 00
01 26
01 00
BE EF
03
06 00
30 33
02 00
01 26
00 00
off
BE EF
03
06 00
47 33
01 00
02 26
00 00
on
BE EF
03
06 00
D7 32
01 00
02 26
01 00
BE EF
03
06 00
74 33
02 00
02 26
00 00
Set
Set
Set
Get
IR Remote Rear
Command data
Header
Set
Get
Set
IR Remote Top
Get
TECHNICAL - 13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement