Panasonic PT-F200 Users Manual

Panasonic PT-F200 Users Manual
S
P
E
C
P ro d u c t N u m b e r :
PT-F200NT
P ro d u c t N a m e :
LCD Projector
F
I
L
E
As of January 2008. Appearance and specifications are subject to change without notice.
< 1 >
S
P
E
C
F
LCD Projector
I
L
E
PT-F200NT
Specifications
100–240 V AC, 50/60 Hz
330 W (Approx. 4.5 W in standby mode with fan stopped. 25 W in
standby mode when controlled by a Web browser.)
Dichroic mirror separation/prism synthesis system
Optical system
0.7˝ (17.78 mm) diagonal, 4:3 aspect ratio
LCD panel
Panel size
Transparent LCD panel (x 3, R/G/B)
Display method
Active matrix
Drive method
786,432 (1,024 x 768) x 3, total of 2,359,296 pixels
Pixels
Stripe
Pixel configuration
Manual zoom (1:1–1:2), manual focus
Lens
F 1.7– 2.6, f 21.6 – 43.0 mm
250 W UHM™ lamp
Lamp
Full color (16,777,216 colors)
Colors
3,500 lumens
Brightness * 1
80%
Center-to-corner uniformity * 1
400:1 (full on/full off)
Contrast ratio* 1
1,024 x 768 pixels (Input signals that exceed this resolution will be
Resolution
RGB
converted to 1,024 x 768 pixels.)
Horizontal: 15 – 91 kHz, Vertical: 50– 85 Hz
Scanning frequency
RGB
480i (525i): fH 15.75 kHz; fV 60 Hz
YPBPR
576i (625i): fH 15.63 kHz; fV 50 Hz
480p (525p): fH 31.50 kHz; fV 60 Hz
576p (625p): fH 31.25 kHz; fV 50 Hz
720/60p (750p): fH 45.00 kHz; fV 60 Hz
720/50p (750p): fH 37.50 kHz; fV 50 Hz
1080/60i (1125i): fH 33.75 kHz; fV 60 Hz
1080/50i (1125i): fH 28.13 kHz; fV 50 Hz
NTSC, NTSC4.43, PAL-M, PAL60: fH 15.75 kHz; fV 60 Hz
S-Video/Video
PAL, SECAM, PAL-N: fH 15.63 kHz; fV 50 Hz
838 –7,620 mm (33 – 300 inches) diagonally, 16:10 aspect ratio
Projection size
1.2 m – 18.1 m (3´11˝– 59´5˝), 4:3 aspect ratio
Throw distance
Vertical: ±50%, horizontal: ±32%
Optical axis shift
Vertical: approx. ±30°
Keystone correction range
Front/rear, ceiling/desk (menu selection)
Installation
17 languages: English, French, German, Spanish, Italian, Korean,
On-screen menu
Russian, Chinese, Japanese, Swedish, Norwegian, Danish, Portuguese,
Polish, Hungarian, Czech, and Thai
4 cm (round), x 1
Built-in speakers
Size
3.0 W (monaural)
Output power
D-sub HD 15-pin x 1
Terminals
COMPUTER 1 IN
R, G, B: 0.7 Vp-p, 75 ohms, Sync on green: 1.0 V [p-p], 75 ohms,
HD/SYNC, VD: TTL (positive/negative polarity compatible)
COMPUTER 2 IN/COMPUTER 1 OUT
D-sub HD 15-pin x 1 (input/output selectable using on-screen menu)
R, G, B: 0.7 V [p-p], 75 ohms, Sync on green: 1.0 V [p-p], 75 ohms,
HD/SYNC, VD: TTL (positive/negative polarity compatible)
RCA pin x 3, Y: 1.0 V [p-p] (including sync signal), 75 ohms,
COMPONENT IN
PB, PR: 0.7 V [p-p], 75 ohms
VIDEO IN
RCA pin x 1, 1.0 Vp-p, 75 ohms
S-VIDEO IN
Mini DIN 4-pin x 1, Y: 1.0 V [p-p], C: 0.286 V [p-p], 75 ohms
AUDIO IN (COMPUTER 1) M3 (stereo) x 1, 0.5 V [rms]
AUDIO IN (COMPUTER 2) M3 (stereo) x 1, 0.5 V [rms]
AUDIO IN (COMPONENT/VIDEO/S-VIDEO)
RCA (L, R) x 1, 0.5 V [rms]
AUDIO OUT
M3 (stereo) x 1, 0 – 2.0 V [rms] (variable)
SERIAL
D-sub 9-pin x 1, for external control (RS-232C)
REMOTE
D-sub 9-pin x 1, for external control (contact control)
LAN
RJ-45 x 1, 10BASE-T/100BASE-TX/1000BASE-T
Power cord length
2 m/6´7˝
Cabinet material
Moulded plastic (PC+ABS)
Dimensions (W x H x D)
432 x 124.5 x 319 mm (17˝ x 4-29/32˝ x 12-9/16˝)
Weight
6.2 kg (13.7 lbs.)
Operating environment
Temperature
0°– 40°C (32°–104°F)
Humidity
20%– 80% (no condensation)
Power supply
Power consumption
As of January 2008
< 2 >
S
P
E
F
C
I
L
E
PT-F200NT
LCD Projector
Remote control unit
Power supply
Operation range* 2
Dimensions (W x H x D)
Weight
Standard
Modulation
IEEE 802.11b
IEEE 802.11g
Transmission system
IEEE 802.11b
IEEE 802.11g
Wireless LAN
Transmission speed
IEEE 802.11b
IEEE 802.11g
Operating range* 2
Frequency range
Channels
Infrastructure mode
Ad-hoc mode
Wireless Manager ME 4.5 system requirements
OS
3 V DC (AA battery x 2)
Approx. 15 m (49´3˝) when operated from directly in front of the
signal receptor
48 x 163 x 24.5 mm (1-7/8˝ x 6-13/32˝ x 31/32˝)
117 g (4.1 oz) (including batteries)
IEEE 802.11b/g
Direct sequence spread spectrum (DSSS) system
Orthogonal frequency division multiplex (OFDM) system
CCK (11/5.5 Mbps), DQPSK (2 Mbps), DBPSK (1 Mbps)
64-QAM (54/48 Mbps), 16-QAM (36/24 Mbps), QPSK (18/12 Mbps),
BPSK (9/6 Mbps)
11 Mbps, 5.5 Mbps, 2 Mbps, 1 Mbps
54 Mbps, 48 Mbps, 36 Mbps, 24 Mbps, 18 Mbps, 12 Mbps, 9 Mbps,
6 Mbps
Approx. 30 m
PT-F200NTE/F200NTEA: 2,412 MHz–2,472 MHz
PT-F200NTU: 2,412 MHz–2,462 MHz
PT-F200NTE/F200NTEA: 1–13 ch, PT-F200NTU: 1–11 ch
WPA-PSK (TKIP/AES), 128/64-bit WEP
128/64-bit WEP
To use network functions, a PC is required that meets the conditions
given below.
Microsoft® Windows® 2000 Professional, Windows® XP Professional,
Windows® XP Home Edition, Windows Vista® Ultimate 32-bit,
Windows Vista® Business 32-bit, Windows Vista® Home Premium
32-bit, Windows Vista® Home Basic 32-bit
Apple Mac OS X 10.4 (Tiger) and OS X 10.5* (Leopard)
* MacBook and MacBook Pro with the Intel Core 2 Duo processor only.
NOTE: Some functions are not available with Windows Vista ® and Mac.
Web browser
CPU
Memory
Free hard disk space
CD-ROM drive
Wireless LAN
Windows®: Internet Explorer 6.0 or later, or Netscape Communicator
7.0 or later
Mac OS: Safari 2.0 or later
Windows®: Intel® Pentium® III or higher, or other compatible processor
(1 GHz or higher is recommended.)
Mac OS X 10.4: 800-MHz or higher PowerPC G4, or 1.8-GHz or higher
Intel® Core™ processor
Mac OS X 10.5: MacBook and MacBook Pro with the Intel ® Core™ 2
Duo processor only
256 MB or more
60 MB or more
CD-ROM drive or DVD drive
IEEE 802.11b/g compatible (built-in wireless LAN system or external
IEEE 802.11b/g LAN card must be installed and running normally.)
NOTE: Some IEEE 802.11g/b wireless LAN may not allow connection to the projector.
Wired LAN connector
RJ-45
NOTE: Use Category 5e (or higher) cables for use with 1000BASE-T.
Supplied accessories
Power cord
Power cord secure lock
Wireless remote control
Batteries for remote control
Wireless Manager ME 4.5 (CD-ROM)
Safety wire rope
Replacement lamp unit: ET-LAF100
Replacement filter unit: ET-RFF100
Ceiling mount bracket for high ceilings: ET-PKF100H
Ceiling mount bracket for low ceilings: ET-PKF100S
Optional accessories
* 1:
Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
* 2: Operation range differs depending on environments.
Weights and dimensions shown are approximate. Specifications are subject to change without notice. Product availability differs depending on region and country.
This product may be subject to export control regulations. UHM is a trademark of Matsushita Electric Industrial Co., Ltd. Intel, Pentium, and Intel Core are trademarks
or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Microsoft, Windows Vista and Windows are either registered
trademarks or trademarks of Microsoft Corp. in the United States and/or other countries. Apple, Mac, Mac OS, and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries. PowerPC is a trademark of International Business Machines Corporation, registered in the U.S. PJLink is a registered trademark
or trademark in Japan, the United States, and other countries and regions All other trademarks are the property of their respective trademark owners.
As of January 2008
< 3 >
S
P
E
C
F
I
L
E
PT-F200NT
LCD Projector
Dimensions
319
(12-9/16˝)
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
9.5
(3/8˝)
53
(2-3/32˝)
309
(12-5/32˝)
115
(4-17/32˝)
124.5
(4-29/32˝)
70
(2-3/4˝)
85
(3-11/32˝)
432 (17˝)
213
(8-3/8˝)
Terminals
4
1
8
2
9
3
10
As of January 2008
5
12
11
6
7
1
LAN
2
Computer 1 input
3
Computer 2 input/computer 1 output
4
S-Video input
5
Video input
6
Component input
7
Audio input for component/S-Video/video
8
Serial input
9
Remote input
10
Audio input for computer 1
11
Audio input for computer 2
12
Audio output
< 4 >
S
P
E
F
C
I
L
E
PT-F200NT
LCD Projector
Standard setting-up positions
369–449
H
Upper edge of projected image
(14-17/32˝–
17-11/16˝)
Adjustable
in 20-mm
(15/32-inch)
step
unit : mm (inch)
Ø49
(1-15/16˝)
Ø43
(1-11/16˝)
L
195
(7-11/16˝)
Projected image
H
L
Lower edge of projected image
A: Distance to screen
E: Height from the edge of screen to
center of lens
70 (2-3/4˝)
65
NOTE:
Illustrations show the projector installed
using optional ceiling bracket.
13 (1/2˝)
L
Projected image
This illustration is not drawn to scale.
Projection distance (screen aspect ratio 4:3)
*
Projection size
(diagonal)
0.84
1.02
1.27
1.52
1.78
2.03
2.29
2.54
3.05
3.81
5.08
6.35
7.62
m
m
m
m
m
m
m
m
m
m
m
m
m
/ 33˝
/ 40˝
/ 50˝
/ 60˝
/ 70˝
/ 80˝
/ 90˝
/ 100˝
/ 120˝
/ 150˝
/ 200˝
/ 250˝
/ 300˝
Projection distance (L)
Min (wide)
–
1.2 m
1.5 m
1.8 m
2.1 m
2.4 m
2.7 m
3.0 m
3.6 m
4.5 m
6.0 m
7.6 m
9.1 m
/
/
/
/
/
/
/
/
/
/
/
/
/
–
3.8´
4.8´
5.8´
6.8´
7.8´
8.8´
9.8´
11.8´
14.8´
19.8´
24.8´
29.8´
Max (telephoto)
1.9
2.4
3.0
3.6
4.2
4.8
5.4
6.0
7.2
9.0
12.1
15.1
18.1
m
m
m
m
m
m
m
m
m
m
m
m
m
/
/
/
/
/
/
/
/
/
/
/
/
/
Height from the edge of screen
to center of lens (H)
6.4´
7.8´
9.8´
11.7´
13.7´
15.7´
17.7´
19.7´
23.7´
29.6´
39.6´
49.5´
59.5´
0
0
0
0
0
0
0
0
0
0
0
0
0
–
–
–
–
–
–
–
–
–
–
–
–
–
0.25
0.30
0.38
0.46
0.53
0.61
0.69
0.76
0.91
1.14
1.52
1.91
2.29
m
m
m
m
m
m
m
m
m
m
m
m
m
/
/
/
/
/
/
/
/
/
/
/
/
/
0
0
0
0
0
0
0
0
0
0
0
0
0
–
–
–
–
–
–
–
–
–
–
–
–
–
0.8´
1.0´
1.3´
1.5´
1.8´
2.0´
2.3´
2.5´
3.0´
3.8´
5.0´
6.3´
7.5´
This distance is especially recommended for ceiling-mounted use and
other permanent installations.
NOTE:
Values shown are approximate. The value
for L (distance to screen) varies slightly
depending on the zoom lens characteristics.
When the shortest projection distance is
used, a small amount of distortion may
occur in the image due to the zoom lens
characteristics.
The value for H (the height from the edge
of the screen to the centre of the lens) is
the value when the horizontal optical axis
shift function is not used. The value
decreases when the horizontal optical
axis shift function is used. For details,
see Shift range on page 6.
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
Aspect ratio 4:3
minimum
maximum
L (m) = (diagonal screen size in inches) x 0.0304 - 0.048
L (m) = (diagonal screen size in inches) x 0.0606 - 0.057
NOTE:
Distances calculated with the above equations will include a slight error.
As of January 2008
< 5 >
S
P
E
F
C
I
L
E
PT-F200NT
LCD Projector
Shift range
Optical axis shift function allows to shift the position of a projected image as shown below.
H
(Width of
projected image)
0.32H
Standard postition
of projected image
0.5V
V
(Height of
projected image)
0.5V
0.32H
Installable Angle
Install the projector at an angle within the range shown below..
• Vertical direction
The projector may be installed at a vertical angle of ±30°.
• Horizontal direction
The projector may not be angled horizontally.
As of January 2008
< 6 >
S
P
E
F
C
I
L
E
PT-F200NT
LCD Projector
Computer data compatibility
This projector accepts up to 91 kHz horizontal scanning frequency and 162 MHz dot clock.
NOTE:
Pixel thinning is applied to signals that exceed a dot clock frequency of 110 MHz. The display resolution of this projector is 1,024
x 768 pixels. If the display resolution indicated in the above data exceeds this resolution, image compression will be used to convert the input signal to 1,024 x 768 pixels.
List of compatible signals
Display mode
Display
resolution
(dots) 1
Scanning frequency Dot clock
H
V
frequency
(kHz)
(kHz)
(MHz)
Picture
quality 2
Input terminal
NTSC/NTSC4.43/PAL-M/PAL60
720 x 480i
15.7
59.9
-
A
PAL/PAL-N/SECAM
720 x 576i
15.6
50.0
-
A
525i (480i)
720 x 480i
15.7
59.9
13.5
A
625i (576i)
720 x 576i
15.6
50.0
13.5
A
525p (480p)
720 x 480
31.5
59.9
27.0
A
625p (576p)
720 x 576
31.3
50.0
27.0
A
1,280 x 720
45.0
60.0
74.3
A
COMPONENT (YP B P R )/
37.5
50.0
74.3
A
COMPUTER (RGB only)
33.8
60.0
74.3
A
COMPONENT (YP B P R )/
28.1
50.0
74.3
A
COMPUTER (RGB only) 3
31.5
70.1
25.2
A
COMPUTER (RGB only)
37.9
85.1
31.5
A
750 (720)/60p
750 (720)/50p
1125 (1080)/60i
1,920 x 1,080i
1125 (1080)/50i
VESA70
640 x 400
VESA85
640 x 480
31.5
59.9
25.2
A
VGA65
35.0
66.7
30.2
A
VGA72
37.9
72.8
31.5
A
VGA75
37.5
75.0
31.5
A
VGA85
43.3
85.0
36.0
A
35.2
56.3
36.0
A
SVGA60
37.9
60.3
40.0
A
SVGA70
48.1
72.2
50.0
A
SVGA75
46.9
75.0
49.5
A
SVGA85
53.7
85.1
56.3
A
VGA60
SVGA55
800 x 600
MAC16
832 x 624
49.7
74.6
57.3
A
XGA50
1,024 x 768
39.6
50.1
51.9
AA
XGA60
48.4
60.0
65.0
AA
XGA70
56.5
70.1
75.0
AA
XGA75
60.0
75.0
78.8
AA
XGA85
68.7
85.0
94.5
AA
44.8
59.9
74.5
A
37.1
49.8
60.5
A
39.6
49.9
65.3
A
47.8
59.9
79.5
A
41.3
50.0
68.0
A
49.1
60.2
69.1
A
49.7
59.8
83.5
A
64.0
71.2
94.2
A
MXGA75
67.5
74.9
108.0
A
MXGA85
76.7
85.0
121.5
B
WIDE750 (720)
WXGA768/50
1,280 x 720
1,280 x 768
WXGA768/60
WXGA800/50
1,280 x 800
WXGA800/60
MXGA70
1,152 x 864
MAC21
1,152 x 870
68.7
75.1
100.0
A
MSXGA60
1,280 x 960
60.0
60.0
108.0
A
1,280 x 1,024
64.0
60.0
108.0
A
80.0
75.0
135.0
B
91.1
85.0
157.5
B
64.0
60.0
108.0
A
65.1
59.9
122.4
B
SXGA60
SXGA75
SXGA85
SXGA60+
1,400 x 1,050
1,440 x 900
55.9
59.9
106.5
A
UXGA60
1,600 x 1,200
75.0
60.0
162.0
B
WSXGA+
1,680 x 1,050
65.3
60.0
146.3
B
WUXGA
1,920 x 1,200
74.6
59.9
193.3
B
WXGA+
VIDEO/S-VIDEO
COMPONENT (YP B P R )/
COMPUTER (RGB only)
1. The “i” appearing after the resolution indicates an interlaced signal.
2. The following symbols are used to indicate picture quality.
AA: Maximum picture quality can be obtained. A: Signals are converted by the image processing circuit before picture is projected.
B: Pixels are thinned by the image processing circuit before picture is projected.
3. When 750 (720)/60p or 750 (720)/50p signals are input to a computer input terminal, images are projected in the WIDE750 (720) format. Be sure
to run the auto setup function.
As of January 2008
< 7 >
S
P
E
F
C
I
L
E
PT-F200NT
LCD Projector
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below.
Pin assignments and signal names
6 9
1
5
No. Signal name
Description
No. Signal name
1
–
NC
6
–
2
TXD
Send data
7
CTS
3
RXD
Receive data
8
RTS
4
–
Connected internally
9
–
5
GND
Ground
D-sub HD 9-pin, female
Signal name
NC
Connected internally
Connected internally
NC
* Effective when connected to a PC having proper functions.
Communication conditions (factory setting)
Signal level
RS-232C-compliant
Synchronization method
Start-stop synchronization
Baud rate
9,600 bps
Parity
None
Character length
8 bits
Stop bit
1 bit
X parameter
None
S parameter
None
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
STX
C1 C2 C3
Start
(1 byte)
:
P1 P2 P3 P4
Colon
Parameter
Command
(1 byte)
(1-4 bytes)
(3 bytes)
(Control and/or query commands)
ETX
End
(1 byte)
CAUTIION
It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then
try sending or receiving again. When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector
before sending the next command. Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for
command response to 10 seconds or more.
NOTE:
If a wrong command is received, the projector will send an ER401 command to the computer.
When sending commands without parameters, a colon (:) is not necessary.
Cable specifications
Projector
1
PC (DTE)
NC
NC
2
2
3
3
4
NC
NC
DSR
NC
6
6
7
7
8
8
9
4
5
5
As of January 2008
1
NC
NC
9
< 8 >
S
P
E
C
F
I
L
E
PT-F200NT
LCD Projector
Control commands
Command: <Parameter>
Function
Callback: <Parameter>
P ON * 1
P OF * 1
A VL:<pl>
I IS:<input signal>
O ST
O FZ:<off on>
O EN
O XG:<off on>
V PM:<NAT>
V PM:<STD>
V PM:<DYN>
V PM:<BBD>
V XX:DLVI0=<+00000>
V XX:DLVI0=<+00001>
V XX:DLVI0=<+00002>
A UU
A UD
O MN
O CU
O CD
O CL
O CR
O AS
O SH * 1/* 2
O IX
D ZU
D ZD
T SD:<date>
T ST:<time>
Power on (standby mode on)
Power off (standby mode off)
Volume control
Input signal selection
The same function as “default” button
Freeze
Enter
Wide mode
Picture mode: Natural
Picture mode: Standard
Picture mode: Dynamic
Picture mode: Blackboard
Daylight View: Off
Daylight View: Auto
Daylight View: On
Volume up
Volume down
Menu
Cursor up
Cursor down
Cursor left
Cursor right
Auto setup
Shutter
Index window
Digital zoom: Enlargement
Digital zoom: Reduction
Date setting
Time setting
PON
POF
AVL:<pl>
IIS:<input signal>
OST
OFZ:<off_on>
OEN
OXG:<off_on>
VPM:<NAT>
VPM:<STD>
VPM:<DYN>
VPM:<BBD>
VXX:DLVI0=<+00000>
VXX:DLVI0=<+00001>
VXX:DLVI0=<+00002>
AUU
AUD
OMN
OCU
OCD
OCL
OCR
OAS
OSH
OIX
DZU
DZD
TSD:<date>
TST:<time>
*1
*2
Parameter value
Min
Max
–
–
0
–
–
0
–
0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
63
–
–
1
–
1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Do not send PON, POF, or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle.
When a command other than OSH is sent while the shutter function is operating, the projector will send an ER401 command in reply and release the shutter function.
Status asking commands
Command
Description
Q PW
Q $S
Q IN
Q AV
Q VC
Q VT
Q VB
Q VR
Q VS
Q WR
Q WG
Q WB
Q HP
Q VP
Q CP
Q DC
Q SP
Q LG
Q XG
Q VX:DLVI0
Standby power status
Lamp status
Input signal status
Volume adjustment value
Color adjustment value
Tint adjustent value
Brightness adjustment value
Contrast adjustment value
Sharpness adjustment value
White balance: R adjustment value
White balance: G adjustment value
White balance: B adjustment value
Horizontal position adjustment value
Vertical position adjustment value
Clock phase adjustment value
Dot clock adjustment value
Projection method status
On-screen menu language
Wide mode status
Daylight View status
Off
Auto
On
Picture mode status
Natural
Standard
Dynamic
Blackboard
Freeze status
Lamp run time
Shutter function status
Keystone correction status
Color temperature adjustment status
Date setting status
Time setting status
Q PM
Q FZ
Q $L
Q SH
Q KS
Q TE
Q GD
Q GT
As of January 2008
Callback
<Parameter>
<power condition>
<lamp condition>
<input signal>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<off_on>
<+00000>
<+00001>
<+00002>
<NAT>
<STD>
<DYN>
<BBD>
<off_on>
<acctch>
<off_on>
<pl>
<color temp>
<date>
<time>
< 9 >
S
P
E
C
F
I
L
E
PT-F200NT
LCD Projector
Parameter format
Parameter format
<pl>
Size (Byte)
Difinition
<off on>
<input signal>
3 (1 or 2 bytes also
possible when
under control)
1
3
<installation>
<language>
1
3
<power condition>
<lamp condition>
3
1
<acctch>
<color temp>
<date>
4
1
8
<time>
6
Dicimal without signs: 0-999 (000, 001, 002...999)
Dicimal with signs: -99 to +99 (-99...-01, +00, +01, +02...+99)
Callback from the projector is 3 Byte.
0 = off, 1 = on
RG1 = computer 1, RG2 = computer 2, NWP = network,
YUV = component, VID = video, SVD = S-Video
0 = front, 1 = rear, 2 = ceiling and front, 3 = ceiling and rear
ENG = English, DEU = German, FRA = French, ESP = Spanish,
ITL = Italian, JPN = Japanese, CHI = Chinese, POR = Portuguese,
SVE = Swedish, NOR = Norwegian, DAN = Danish, POL = Polish,
CES = Czech, MAG = Hungarian, RUS = Russian, THA = Thai, KOR = Korean
000 = power on (standby mode on), 001 = power off (standby mode off)
0 = standby, 1 = lamp on under control, 2 = lamp off,
3 = lamp off under control
Dicimal without signs: 0000-9999 hours
0 = economy, 1 = normal
y1y2y3y4m1m2d1d2w = year (y) month (m) day (d) day of week (w)
Day of week: Monday = 1, Tuesday = 2, ... Sunday = 7
h1h2m1m2s1s2 = hour (h) minute (m) second (s)
NOTE: If a wrong command is received, the projector will send an ER401 command to the computer.
Command example
To set the volume to +30, send the command as shown below.
STX
Start
AVL
:
Command
30
ETX
Parameter
End
NOTE: When sending commands without parameters, a colon (:) is not necessary.
As of January 2008
< 10 >
S
P
E
C
F
I
L
E
PT-F200NT
LCD Projector
Notes on Projector Placement and Operation:
The projector uses a high-wattage lamp that becomes very hot during operation.
Please observe the following precautions.
1.
Never place objects on top of the projector while it is operating.
2.
Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector's exhaust openings. In addition to this space, also ensure that there is a sufficient work space for removing and installing the
lamp, filter and other parts.
3.
If the projector is placed in a box or enclosure, ensure the temperature of the air surrounding the projector is
between 0°C/32°F and 35°C/95°F. Also make sure the projector’s intake and exhaust openings are not blocked.
Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake openings.
200 mm (7-7/8˝) or more
500 mm (7-5/8˝) or more
500 mm (7-5/8˝) or more
Direction of Air Intake and Exhaust
Intake
Exhaust
Operating the Projector Continuously
1.
When the projector is operated continuously 10 hours or more, the lamp replacement cycle decreases.
2.
The lamp replacement cycle also decreases when the projector is used for short periods of time (less than one hour)
repeatedly.
Replacing the Filter Unit
The projector is equipped with the Auto Rolling Filter (ARF) function, which automatically winds the air filter to set a new
filter element in place according to operating conditions. The filter unit replacement cycle ranges from approximately 6,000
hours maximum to approximately 500 hours minimum. Please purchase the ET-RFF100 filter unit for replacement use.
Weights and dimensions shown are approximate. Specifications are subject to change without notice. Product availability differs depending on region and country.
This product may be subject to export control regulations. UHM is a trademark of Matsushita Electric Industrial Co., Ltd. Intel, Pentium, and Intel Core are trademarks
or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Microsoft, Windows Vista and Windows are either registered
trademarks or trademarks of Microsoft Corp. in the United States and/or other countries. Apple, Mac, Mac OS, and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries. PowerPC is a trademark of International Business Machines Corporation, registered in the U.S. PJLink is a registered trademark
or trademark in Japan, the United States, and other countries and regions All other trademarks are the property of their respective trademark owners.
As of January 2008
< 11 >
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising