Panasonic PT-LB75NTU Technical Appendix

Panasonic PT-LB75NTU Technical Appendix
S
P
E
C
P ro d u c t N u m b e r :
PT-LB75NT
P ro d u c t N a m e :
LCD Projector
F
As of May 2008. Specifications subject to change without notice.
I
L
E
< 1 >
S
P
E
C
F
I
L
E
Portable LCD Projector
PT-LB75NT
Specifications
100–240 V AC, 50/60 Hz
300 W (approx. 3 W in standby mode with fan stopped. 28 W in
standby mode when controlled by a Web browser.)
Dichroic mirror separation/prism synthesis system
Optical system
0.63˝ (16 mm) diagonal (4:3 aspect ratio)
LCD panel
Panel size
Transparent LCD panel (x 3, R/G/B)
Display method
Active matrix
Drive method
786,432 (1,024 x 768) x 3, total of 2,359,296 pixels
Pixels
Stripe
Pixel configuration
Manual zoom (1:1–1:1.2), manual focus
Lens
F 1.7–1.9, f 18.5– 22.2 mm
1.4–1.7:1
Throw ratio
220 W UHM™ lamp
Lamp
Full color (16,777,216 colors)
Colors
2,600 lumens
Brightness*1
85%
Center-to-corner uniformity ratio*1
500:1 (full on/full off)
Contrast ratio*1
1,024 x 768 pixels (Input signals that exceed this resolution will be
Resolution RGB
converted to 1,024 x 768 pixels.)
Horizontal: 15.00 – 91.00 kHz, Vertical: 50 – 85 Hz
Scanning frequency
RGB
480i (525i): fH 15.75 kHz; fV 60 Hz
YPBPR
576i (625i): fH 15.63 kHz; fV 50 Hz
480p (525p): fH 31.50 kHz; fV 60 Hz
576p (625p): fH 31.25 kHz; fV 50 Hz
720/60p (750p): fH 45.00 kHz; fV 60 Hz
1080/60i (1125i): fH 33.75 kHz; fV 60 Hz
1080/50i (1125i): fH 28.13 kHz; fV 50 Hz
NTSC, NTSC4.43, PAL-M, PAL60: fH 15.75 kHz; fV 60 Hz
S-Video/Video
PAL, SECAM, PAL-N: fH 15.63 kHz; fV 50 Hz
838–7,620 mm (33– 300 inches) diagonally, 4:3 aspect ratio
Projection size
5:1 (fixed)
Optical axis shift
Vertical: approx. ±30°
Keystone correction range
17 languages: English, French, German, Spanish, Italian, Korean,
On-screen menu
Russian, Chinese, Japanese, Swedish, Norwegian, Danish, Portuguese,
Polish, Hungarian, Czech, and Thai
Front/rear, ceiling/desk (menu selection)
Installation
4 x 2 cm, x 1, oval
Built-in speakers
Size
1.0 W (monaural)
Output power
Terminals
COMPUTER (RGB) 1 IN D-sub HD 15-pin x 1
R, G, B: 0.7 Vp-p, 75 Ω, Sync on green: 1.0 V [p-p], 75 Ω,
RGB signal
HD/SYNC, VD: TTL (positive/negative polarity compatible)
Y: 1.0 V [p-p] (including sync signal), 75 Ω, PB, PR: 0.7 Vp-p, 75 Ω
YPBPR signal
COMPUTER (RGB) 2 IN/1 OUT
D-sub HD 15-pin x 1 (input/output selectable using on-screen menu)
RGB signal
R, G, B: 0.7 V [p-p], 75 Ω, Sync on green: 1.0 V [p-p], 75 Ω,
HD/SYNC, VD: TTL (positive/negative polarity compatible)
Y: 1.0 V [p-p] (including sync signal), 75 Ω, PB, PR: 0.7 V [p-p], 75 Ω
YPBPR signal
VIDEO IN
RCA pin x 1, 1.0 Vp-p, 75 Ω
S-VIDEO IN
Mini DIN 4-pin x 1, Y: 1.0 V [p-p], C: 0.286 V [p-p], 75 Ω
COMPUTER AUDIO IN
M3 (L, R) x 1, 0.5 V [rms], for COMPUTER (RGB) 1 and 2
AUDIO IN
RCA (L, R) x 1, 0.5 V [rms], for VIDEO and S-VIDEO
VARIABLE AUDIO OUT
M3 (L, R) x 1, 0 – 2.0 V [rms]
SERIAL
D-sub 9-pin x 1, for external control (RS-232C)
Power cord length
2 m/6.6´
Cabinet material
Moulded plastic (PC+ABS)
Dimensions (W x H x D)
368 x 88 x 233 mm (14-1/2˝ x 3-15/32˝ x 9-3/16˝)* 2
Weight*2
2.96 kg (6.5 lbs.)
0°– 40°C (32°–104°F)
Operating environment
Temperature
20%–80% (no condensation)
Humidity
Power supply
Power consumption
As of May 2008
< 2 >
S
P
E
F
C
I
L
E
PT-LB75NT
Portable LCD Projector
Remote control unit
Power supply
Operation range*3
Dimensions (W x H x D)
Weight*2
Standard
Modulation
IEEE 802.11b
IEEE 802.11g
Transmission system
IEEE 802.11b
IEEE 802.11g
Wireless LAN
Transmission speed
IEEE 802.11b
IEEE 802.11g
Operating range*3
Frequency range
Channels
Wireless Manager ME 5.0 system requirements
OS
3 V DC (AA battery x 2)
Approx. 15 m (49´3˝) when operated from directly in front of the signal
receptor
48 x 163 x 24.5 mm (1-7/8˝ x 6-13/32˝ x 31/32˝)
117 g (4.1 oz) (including batteries)
IEEE 802.11b/g (ARIB STD-T66)
Direct sequence spread spectrum (DS-SS) system
Orthogonal frequency division multiplex (OFDM) system
CCK (11/5.5 Mbps), DQPSK (2 Mbps), DBPSK (1 Mbps)
64-QAM (54/48 Mbps), 16-QAM (36/24 Mbps), QPSK (18/12 Mbps),
BPSK (9/6 Mbps)
11 Mbps, 5.5 Mbps, 2 Mbps, 1 Mbps
54 Mbps, 48 Mbps, 36 Mbps, 24 Mbps, 18 Mbps, 12 Mbps, 9 Mbps,
6 Mbps
Approx. 30 m (98´5˝)
PT-LB80NTE/LB80NTEA: 2,412 MHz–2,472 MHz
PT-LB80NTU: 2,412 MHz – 2,462 MHz
PT-LB80NTE/LB80NTEA: 1–13 ch
PT-LB80NTU: 1–11 ch
To use network functions, a PC is required that meets the conditions
given below.
Microsoft® Windows® 2000 Professional SP4, Windows® XP
Professional, Windows® XP Home Edition, Windows® XP Tablet PC
Edition, Windows Vista® Ultimate 32-bit, Windows Vista® Business
32-bit, Windows Vista® Home Premium 32-bit, Windows Vista®
Home Basic 32-bit
Apple Mac OS X 10.4 (Tiger) and OS X 10.5* (Leopard)
NOTE: Some functions are not available with Windows Vista ® and Mac.
Web browser
CPU
Memory
Free hard disk space
CD-ROM drive
Wireless LAN
Windows®: Internet Explorer 6.0 or later, or Netscape Communicator
7.0 or later
Mac OS: Safari 2.0 or later
Windows®: Intel® Pentium® III or higher, or other compatible processor
(1 GHz or higher is recommended.)
Mac OS X: 1-GHz or higher PowerPC G4, or 1.8-GHz or higher Intel ®
Core™ processor
256 MB or more (512 MB or higher is recommended for Mac OS X)
60 MB or more
CD-ROM drive or DVD drive
IEEE 802.11b/g compatible (built-in wireless LAN system or external
IEEE 802.11b/g LAN card must be installed and running normally.)
NOTE: Some IEEE 802.11g/b wireless LAN may not allow connection to the projector. For Mac OS, Built-in IEEE 802.11b/g wireless LAN adapter must be
installed and running normally.
Supplied accessories
Optional accessories
Power cord
Power cord secure lock
Wireless remote control
Batteries for remote control
VGA cable for RGB signals (1.8 m/5´11˝)
Carrying bag
Wireless Manager ME 5.0 (CD-ROM)
Replacement lamp unit: ET-LAB80
Ceiling mount bracket: ET-PKB80
*1: Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*2: Values indicate overall average values of the product.
*3: Operation range differs depending on environments. Weights and dimensions shown are approximate. Specifications
subject to change without notice.
Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product may be subject to export control regulations. UHM is a trademark of Matsushita Electric Industrial Co., Ltd. Intel and Pentium are registered trademarks of Intel Corporation. Microsoft, Windows
Vista and Windows are either registered trademarks or trademarks of Microsoft Corp. in the United States and/or other countries. Apple, Mac, Mac OS,
Macintosh and Safari are trademarks of Apple Inc., registered in the U.S. and other countries. All other trademarks are the property of their respective
trademark owners. Projection images simulated.
As of May 2008
< 3 >
S
P
E
C
F
I
L
E
PT-LB75NT
Portable LCD Projector
Dimensions
9
(11/32˝)
97
(3-13/16˝)
88
(3-15/32˝)
54.5
(2-5/32˝)
3
(1/8˝)
233
(9-3/16˝)
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
89
(3-1/2˝)
368
(14-1/2˝)
194
(7-5/8˝)
Terminals
4
1
2
3
7
5
6
1
COMPUTER (RGB) 1 input
2
COMPUTER (RGB) 2 input/COMPUTER (RGB) 1 output
3
S-Video input
4
Video input
5
Audio input for Video/S-Video
6
Audio output
7
Audio input for COMPUTER 1/2
8
Serial
8
As of May 2008
< 4 >
S
P
E
F
C
I
L
E
PT-LB75NT
Portable LCD Projector
Standard setting-up positions
369–449
(14-17/32˝–
17-11/16˝)
Adjustable
in 20-mm
(15/32-inch) step.
unit : mm (inch)
ø49
Upper edge of projected image
(1-15/16˝)
H
ø43
(1-11/16˝)
L
195
Projected image
L: Distance to screen
H: Height from the edge of screen to
center of lens
(7-11/16˝)
H
L
Lower edge of projected image
65 (2-9/16˝)
NOTE:
70 (2-3/4˝)
Illustrations show the projector installed
using optional ceiling bracket.
This illustration is not drawn to scale.
13 (1/2˝)
L
Projected image
Projection size
Projection distance (L)
(diagonal)
0.84
1.02
1.27
1.52
1.78
2.03
2.29
2.54
3.05
3.81
5.08
6.35
7.62
m
m
m
m
m
m
m
m
m
m
m
m
m
/ 33˝
/ 40˝
/ 50˝
/ 60˝
/ 70˝
/ 80˝
/ 90˝
/ 100˝
/ 120˝
/ 150˝
/ 200˝
/ 250˝
/ 300˝
Min (wide)
–
1.1 m
1.4 m
1.7 m
2.0 m
2.3 m
2.6 m
2.9 m
3.5 m
4.3 m
5.8 m
7.3 m
8.7 m
/
/
/
/
/
/
/
/
/
/
/
/
/
–
3.7´
4.7´
5.6´
6.6´
7.6´
8.5´
9.5´
11.4´
14.3´
19.0´
23.8´
28.6´
Max (telephoto)
1.1
1.4
1.7
2.1
2.4
2.8
3.1
3.5
4.2
5.2
7.0
8.7
10.5
m
m
m
m
m
m
m
m
m
m
m
m
m
/
/
/
/
/
/
/
/
/
/
/
/
/
3.7´
4.5´
5.6´
6.8´
7.9´
9.1´
10.2´
11.4´
13.7´
17.1´
22.9´
28.7´
34.4´
Height from the edge of screen
to centre of lens (H)
0.08
0.10
0.13
0.15
0.18
0.20
0.23
0.25
0.30
0.38
0.51
0.64
0.76
m
m
m
m
m
m
m
m
m
m
m
m
m
/
/
/
/
/
/
/
/
/
/
/
/
/
0.28´
0.33´
0.42´
0.50´
0.58´
0.67´
0.75´
0.83´
1.00´
1.25´
1.67´
2.08´
2.50´
* This distance is especially recommended for ceiling-mounted use and other
permanent installations.
NOTE:
Values shown are approximate.
The value for L (distance to screen)
varies slightly depending on the zoom
lens characteristics.
When the shortest projection distance is
used, a small amount of distortion may
occur in the image due to the zoom lens
characteristics.
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
Aspect ratio 4 : 3
minimum
L (m) = (diagonal screen size in inches) x 0.0292 – 0.036
maximum
L (m) = (diagonal screen size in inches) x 0.0351 – 0.044
NOTE: Distances calculated with the above equations will include a slight error.
Installable Angle
Install the projector at an angle within the range shown below.
• Vertical direction
The projector
may be installed
at a vertical
angle of ±30°.
As of May 2008
• Vertical direction
The projector may not be angled horizontally.
< 5 >
S
P
E
C
F
I
L
E
PT-LB75NT
Portable LCD Projector
Computer data compatibility
This projector accepts up to 91 kHz horizontal scanning frequency and 162 MHz dot clock.
NOTE:
Pixel thinning is applied to signals that exceed a dot clock frequency of 100 MHz. The display resolution of this projector is 1,024 x 768
pixels. Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.
List of compatible signals
Display mode
Display
resolution
(dots) 1
Scanning frequency Dot clock
H
V
frequency
(kHz)
(kHz)
(MHz)
Picture Input terminal
quality 2
NTSC/NTSC4.43/PAL-M/PAL60
720 x 480i
15.7
59.9
–
A
PAL/PAL-N/SECAM
720 x 576i
15.6
50.0
–
A
525i (480i)
720 x 480i
15.7
59.9
13.5
A
625i (576i)
720 x 576i
15.6
50.0
13.5
A
525p (480p)
720 x 483
31.5
59.9
27.0
A
625p (576p)
720 x 576
31.3
50.0
27.0
A
750 (720)/60p
1280 x 720
45.0
60.0
74.3
A
750 (720)/50p
1280 x 720
37.5
50.0
74.3
A
1920 x 1080i
33.8
60.0
74.3
A
28.1
50.0
74.3
A
31.5
70.1
25.2
A
37.9
85.1
31.5
A
1125 (1080)/60i
1125 (1080)/50i
VESA70
640 x 400
VESA85
640 x 480
31.5
59.9
25.2
A
VGA65
35.0
66.7
30.2
A
VGA72
37.9
72.8
31.5
A
VGA75
37.5
75.0
31.5
A
VGA85
43.3
85.0
36.0
A
35.2
56.3
36.0
A
SVGA60
37.9
60.3
40.0
A
SVGA70
48.1
72.2
50.0
A
SVGA75
46.9
75.0
49.5
A
SVGA85
53.7
85.1
56.3
A
VGA60
SVGA55
800 x 600
MAC16
832 x 624
49.7
74.6
57.3
A
XGA50
1024 x 768
39.6
50.1
51.9
AA
XGA60
48.4
60.0
65.0
AA
XGA70
56.5
70.1
75.0
AA
XGA75
60.0
75.0
78.8
AA
XGA85
68.7
85.0
94.5
AA
39.6
49.9
65.3
A
47.8
59.9
79.5
A
41.3
50.0
68.0
A
49.1
60.2
69.1
A
49.7
59.8
83.5
A
64.0
71.2
94.2
A
MXGA75
67.5
74.9
108.0
A
MXGA85
76.7
85.0
121.5
B
WXGA768
WXGA800
MXGA70
1280 x 768
1280 x 800
1152 x 864
MAC21
1152 x 870
68.7
75.1
100.0
A
MSXGA60
1280 x 960
60.0
60.0
108.0
A
1280 x 1024
64.0
60.0
108.0
A
80.0
75.0
135.0
B
91.1
85.0
157.5
B
64.0
60.0
108.0
A
65.1
59.9
122.4
B
SXGA60
SXGA75
SXGA85
SXGA60+
1400 x 1050
1440 x 900
55.9
59.9
106.5
A
UXGA60
1600 x 1200
75.0
60.0
162.0
B
WSXGA+
1680 x 1050
65.3
60.0
146.3
B
WUXGA
1920 x 1200
74.6
59.9
193.3
B
WXGA+
VIDEO/S-VIDEO
COMPUTER (RGB/YP B P R )
COMPUTER (RGB/YP B P R ) 3
COMPUTER (RGB/YP B P R )
COMPUTER (RGB only)
1. The “i” appearing after the resolution indicates an interlaced signal.
2. The following symbols are used to indicate picture quality.
AA Maximum picture quality can be obtained.
A
Signals are converted by the image processing circuit before picture is projected.
B
Signals are compressed by the image processing circuit before picture is projected.
3. When 750 (720)/60p or 750 (720)/50p signals are input to a computer input terminal, images are projected in the WIDE750 (720) format. Be sure
to run the auto setup function.
As of May 2008
< 6 >
S
P
E
F
C
I
L
E
PT-LB75NT
Portable LCD Projector
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below.
Pin assignments and signal names
6 9
1
5
No. Signal name
Description
No. Signal name
1
–
NC
6
–
2
TXD
Send data
7
CTS
3
RXD
Receive data
8
RTS
4
–
Connected internally
9
–
5
GND
Ground
D-sub HD 9-pin, female
Signal name
NC
Connected internally
Connected internally
NC
* Effective when connected to a PC having proper functions.
Communication conditions (factory setting)
Signal level
RS-232C-compliant
Synchronization method
Start-stop synchronization
Baud rate
9,600 bps
Parity
None
Character length
8 bits
Stop bit
1 bit
X parameter
None
S parameter
None
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
STX
C1 C2 C3
Start
(1 byte)
:
P1 P2 P3 P4
Colon
Parameter
Command
(1 byte)
(1-4 bytes)
(3 bytes)
(Control and/or query commands)
ETX
End
(1 byte)
CAUTION
It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then
try sending or receiving again. When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector
before sending the next command. Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for
command response to 10 seconds or more.
NOTE:
If a wrong command is received, the projector will send an ER401 command to the computer.
When sending commands without parameters, a colon (:) is not necessary.
Cable specifications
Projector
1
PC (DTE)
NC
NC
2
2
3
3
4
NC
NC
DSR
NC
6
6
7
7
8
8
9
4
5
5
As of May 2008
1
NC
NC
9
< 7 >
S
P
E
C
F
I
L
E
PT-LB75NT
Portable LCD Projector
Control commands
Command: <Parameter>
Function
Callback: <Parameter>
P O N *1
P O F *1
AVL:<pl>
IIS:<input signal>
OST
OFZ:<off on>
OEN
OXG:<off on>
VPM:<NAT>
VPM:<STD>
VPM:<DYN>
VPM:<BBD>
VXX:DLVI0=<+00000>
VXX:DLVI0=<+00001>
VXX:DLVI0=<+00002>
AUU
AUD
OMN
OCU
OCD
OCL
OCR
OAS
O S H * 1/* 2
OIX
DZU
DZD
Power on (standby mode on)
Power off (standby mode off)
Volume control
Input signal selection
The same function as “default” button
Freeze
Enter
Wide mode
Picture mode: Natural
Picture mode: Standard
Picture mode: Dynamic
Picture mode: Blackboard
Daylight View: Off
Daylight View: Auto
Daylight View: On
Volume up
Volume down
Menu
Cursor up
Cursor down
Cursor left
Cursor right
Auto setup
AV mute
Index window
Digital zoom: Enlargement
Digital zoom: Reduction
PON
POF
AVL:<pl>
IIS:<input signal>
OST
OFZ:<off_on>
OEN
OXG:<off_on>
VPM:<NAT>
VPM:<STD>
VPM:<DYN>
VPM:<BBD>
VXX:DLVI0=<+00000>
VXX:DLVI0=<+00001>
VXX:DLVI0=<+00002>
AUU
AUD
OMN
OCU
OCD
OCL
OCR
OAS
OSH
OIX
DZU
DZD
*1
*2
Parameter value
Min
Max
–
–
0
–
–
0
–
0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
63
–
–
1
–
1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Do not send PON, POF, or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle.
When a command other than OSH is sent while the shutter function is operating, the projector will send an ER401 command in reply and release the shutter function.
Status asking commands
Command
Description
QP W
Q$ S
QI N
QA V
QV C
QV Ç s
QV B
QV R
QV S
QW R
QW G
QW B
QH P
QÇ u P
QC P
QD C
QS P
QL G
QX G
QV X : D L V I 0
Standby power status
Lamp status
Input signal status
Volume adjustment value
Color adjustment value
Tint adjustent value
Brightness adjustment value
Contrast adjustment value
Sharpness adjustment value
White balance: R adjustment value
White balance: G adjustment value
White balance: B adjustment value
Horizontal position adjustment value
Vertical position adjustment value
Clock phase adjustment value
Dot clock adjustment value
Projection method status
On-screen menu language
Wide mode status
Daylight View status
Off
Auto
On
Picture mode status
Natural
Standard
Dynamic
Blackboard
Freeze status
Lamp run time
Shutter function status
Keystone correction status
Color temperature adjustment status
QP M
QF Z
Q$ L
QS H
QK S
QT E
As of May 2008
Callback
<Parameter>
<power condition>
<lamp condition>
<input signal>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<off_on>
<+00000>
<+00001>
<+00002>
<NAT>
<STD>
<DYN>
<BBD>
<off_on>
<acctch>
<off_on>
<pl>
<color temp>
< 8 >
S
P
E
C
F
I
L
E
PT-LB75NT
Portable LCD Projector
Parameter format
Parameter format
<pl>
Size (Byte)
Definition
<off on>
<input signal>
3 (1 or 2 bytes also
possible when
under control)
1
3
<installation>
<language>
1
3
<power condition>
<lamp condition>
3
1
<acctch>
<color temp>
<date>
4
1
8
<time>
6
Decimal without signs: 0 to 999 (000, 001, 002...999)
Decimal with signs: -99 to +99 (-99...-01, +00, +01, +02...+99)
Callback from the projector is 3 Byte.
0 = off, 1 = on
RG1 = computer 1, RG2 = computer 2, NWP = network,
YUV = component, VID = video, SVD = S-Video
0 = front, 1 = rear, 2 = ceiling and front, 3 = ceiling and rear
ENG = English, DEU = German, FRA = French, ESP = Spanish,
ITL = Italian, JPN = Japanese, CHI = Chinese, POR = Portuguese,
SVE = Swedish, NOR = Norwegian, DAN = Danish, POL = Polish,
CES = Czech, MAG = Hungarian, RUS = Russian, THA = Thai, KOR = Korean
000 = power on (standby mode on), 001 = power off (standby mode off)
0 = standby, 1 = lamp on under control, 2 = lamp off,
3 = lamp off under control
Decimal without signs: 0000-9999 hours
0 = economy, 1 = normal, 2 = high
y1y2y3y4m1m2d1d2w = year (y) month (m) day (d) day of week (w)
Day of week: Monday = 1, Tuesday = 2, ... Sunday = 7
h1h2m1m2s1s2 = hour (h) minute (m) second (s)
NOTE: If a wrong command is received, the projector will send an ER401 command to the computer.
Command example
To set the volume to +30, send the command as shown below.
STX
Start
AVL
:
Command
30
ETX
Parameter
End
NOTE: When sending commands without parameters, a colon (:) is not necessary.
As of May 2008
< 9 >
S
P
E
F
C
I
L
E
PT-LB75NT
Portable LCD Projector
Notes on Projector Placement and Operation:
The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the
following precautions.
1.
Never place objects on top of the projector while it is operating.
2.
Make sure there is an unobstructed space of 150 mm (5-29/32˝) or more around the projector’s
exhaust openings.
3.
If the projector is placed in a box or enclosure, ensure the temperature of the air surrounding the
projector is between 0°C/32°F and 35°C/95°F. Also make sure the projector’s intake and exhaust
openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is
not sucked into the intake openings.
200 mm (7-7/8˝) or more
500 mm (7-5/8˝) or more
500 mm (7-5/8˝) or more
Direction of Air Intake and Exhaust
Intake
Exhaust
Operating the Projector Continuously
1.
If the projector is to be operated continuously 10 hours or more, lamp replacement cycle duration
becomes shorter.
2.
The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short
periods (one hour or less).
Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product may be subject to
export control regulations. UHM is a trademark of Matsushita Electric Industrial Co., Ltd. Intel and Pentium are registered trademarks of
Intel Corporation. Microsoft, Windows Vista and Windows are either registered trademarks or trademarks of Microsoft Corp. in the United
States and/or other countries. Apple, Mac, Mac OS, Macintosh and Safari are trademarks of Apple Inc., registered in the U.S. and other
countries. All other trademarks are the property of their respective trademark owners. Projection images simulated.
As of May 2008
< 10 >
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising