Delfield 6025XL-SH Installation manual

Delfield 6025XL-SH Installation manual
Delfield
™
®
6000XL & 6100XL Series Reach Ins
Service, Installation and Care Manual
Please read this manual completely before attempting to install or operate this equipment! Notify carrier of
damage! Inspect all components immediately. See page 2.
Refrigerators and Freezers
IMPORTANT INFORMATION
READ BEFORE USE
PLEASE SAVE THESE INSTRUCTIONS!
October 2012
*9294254*
6000XL Series Service and Installation Manual
Important Warning And Safety Information
WARNING
Read This Manual Thoroughly Before Operating, Installing, Or Performing Maintenance On The Equipment.
WARNING
Failure To Follow Instructions In This Manual Can Cause Property Damage, Injury Or Death.
WARNING
Do Not Store Or Use Gasoline Or Other Flammable Vapors Or Liquids In The Vicinity Of This Or Any Other
Appliance.
WARNING
Unless All Cover And Access Panels Are In Place And Properly Secured, Do Not Operate This Equipment.
WARNING
This Appliance Is Not Intended For Use By Persons Who Lack Experience Or Knowledge, Unless They Have
Been Given Supervision Or Instruction Concerning Use Of The Appliance By A Person Responsible For Their
Safety.
WARNING
This Appliance Is Not To Be Played With.
Warning
Do Not Clean With Water Jet.
WARNING
Do Not Use Electrical Appliances Inside The Food Storage Compartment Of This Appliance.
CAUTION
Observe the following:
•
Minimum clearances must be maintained from all walls and combustible materials.
•
Keep the equipment area free and clear of combustible material.
•
Allow adequate clearance for air openings.
•
Operate equipment only on the type of electricity indicated on the specification plate.
•
Unplug the unit before making any repairs.
•
Retain this manual for future reference.
Delfield
™
2
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
®
6000XL Series Service and Installation Manual
Contents
Serial Number Information
Serial Number Information......................................................... 3
Receiving & Inspecting Equipment............................................ 3
Specifications.............................................................................. 4
Installation................................................................................... 5
Door Reversal Procedures.......................................................... 6
Leg & Caster Installation............................................................. 6
Operation..................................................................................7-8
Evaporator Fan Matrix................................................................. 8
The serial number tag of all 6000XL Series refrigerators and
freezers is located inside the cabinet on the left side.
Always have the serial number of your unit available when
calling for parts or service. A complete list of authorized
Delfield parts depots is available at www.delfield.com.
This manual covers standard units only. If you have a custom
unit, consult the customer service department at the number
listed below.
Maintenance...........................................................................9-10
Wiring Diagrams..................................................................11-15
Refrigeration Package Diagram................................................16
Replacement Parts...............................................................17-18
Standard Labor Guidelines.......................................................19
Standard Warranties............................................................20-22
Regulatory Certifications
The models are certified by:
Notes.........................................................................................23
National Sanitation Foundation (NSF)
©2012 The Delfield Company. All rights reserved. Reproduction without
written permission is prohibited. “Delfield” is a registered trademark of The
Delfield Company.
Underwriters Laboratories (UL)
Receiving And Inspecting The Equipment
Even though most equipment is shipped crated, care should
be taken during unloading so the equipment is not damaged
while being moved into the building.
1. Visually inspect the exterior of the package and skid or
container. Any damage should be noted and reported to
the delivering carrier immediately.
2. If damaged, open and inspect the contents with the
carrier.
3. In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment
notify the carrier. Notification should be made verbally as
Delfield
™
well as in written form.
4. Request an inspection by the shipping company of the
damaged equipment. This should be done within 10 days
from receipt of the equipment.
5. Be certain to check the compressor compartment housing
and visually inspect the refrigeration package. Be sure
lines are secure and base is still intact.
6. Freight carriers can supply the necessary damage forms
upon request.
7. Retain all crating material until an inspection has been
made or waived.
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
3
6000XL Series Service and Installation Manual
Specifications
Voltage
Amps
Storage
Capacity FT3
Shelf
Capacity FT2
H.P.
BTU/HR
Evap.
Temp
R-404A Charge
Oz.
Shipping
Weight
Nema
Plug
6025XL-SH,S
115
6.0
20.0
15.1
1/4
2092
20˚F
12.5
274lbs/124kg
5-15p
6025XL-G,GH
115
6.0
20.0
15.1
1/4
2092
20˚F
12.5
338lbs/153kg
5-15p
6051XL-SH,S
115
8.0
43.5
33.2
1/3
2488
20˚F
12.5
454lbs/206kg
5-15p
6051XL-G,GH
115
8.0
43.5
33.2
1/3
2488
20˚F
12.5
548lbs/249kg
5-15p
6076XL-SH,S
115
16.0
66.5
48.3
1/4, 1/3
2092/2488
20˚F
12.5/12.5
622lbs/282kg
5-20p
6076XL-G,GH
115
16.0
66.5
48.3
1/4, 1/3
2092/2488
20˚F
12.5/12.5
774lbs/351kg
5-20p
6125XL-S,SH
115
9.0
20.0
15.1
1/2
2092
-20˚F
12.5
274lbs/124kg
5-15p
6151XL-S,SH
115
12.0
43.5
33.2
3/4
1923
-20˚F
12.5
454lbs/206kg
5-15p
6176XL-S,SH
120/208230
20.0
66.5
48.3
1/2, 3/4
1516/1923
-20˚F
12.5/12.5
622lbs/282kg
14-20P
Voltage
Amps
Storage
Capacity FT3
Shelf
Capacity FT2
Required
BTU/HR
Evap. Temp
Shipping Weight
6025XLR-SH,S
115
5.0
20.0
15.1
2092
20˚F
274lbs/124kg
6025XLR-G,GH
115
5.0
20.0
15.1
2092
20˚F
338lbs/153kg
6051XLR-SH,S
115
5.0
43.5
33.2
2488
20˚F
454lbs/206kg
6051XLR-G,GH
115
5.0
43.5
33.2
2488
20˚F
548lbs/249kg
6076XLR-SH,S
115
5.0
66.5
48.3
2092/2488
20˚F
622lbs/282kg
6076XLR-G,GH
115
5.0
66.5
48.3
2092/2488
20˚F
774lbs/351kg
6125XLR-S,SH
115
5.0
20.0
15.1
2092
-20˚F
274lbs/124kg
6151XLR-S,SH
115
5.0
43.5
33.2
1923
-20˚F
454lbs/206kg
6176XLR-S,SH
115
5.0
66.5
48.3
1516/1923
-20˚F
622lbs/282kg
Model
Model
Delfield
™
4
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
®
6000XL Series Service and Installation Manual
Installation
Stabilizing
Location
Units represented in this manual are intended for indoor use
only. Be sure the location chosen has a floor strong enough to
support the total weight of the cabinet and contents. A fully loaded
6000XL series can weigh as much as 1500 pounds. Reinforce
the floor as necessary to provide for maximum loading. For the
most efficient refrigeration, be sure to provide good air circulation
inside and out.
Inside cabinet: Do not pack refrigerator so full that air cannot
circulate. The refrigerated air is discharged at the top rear of
the unit. It is important to allow for proper air flow from the
top rear to the bottom of the unit. Obstructions to this air flow
can cause evaporator coil freeze ups and loss of temperature
or overflow of water from the evaporator drain pan. The rear
of the unit has molded ribs and the shelves have a rear turn
up on them to prevent this. However,
bags and other items can still be
located to the far rear of the cabinet.
There is also a return air diffuser
along the top front of the cabinet
interior, this also requires proper air
circulation. Prevent obstruction by
locating large boxes and tall stacks of
product to the bottom of the cabinet.
Outside cabinet: Be sure that the
unit has access to ample air. Avoid
hot corners and locations near stoves
and ovens.
It is recommended that the unit be installed no closer than
2” from any wall with at least 12” of clear space above the
unit. Avoid exposing glass door units to direct sunlight. Direct
sunlight through the glass doors will make the ABS liner
fade and become brittle and will greatly reduce refrigeration
efficiency.
Some models are supplied on casters for your convenience,
ease of cleaning underneath and for mobility. It is very
important, however, that the cabinet be installed in a stable
condition with the front wheels locked while in use.
Should it become necessary to lay the unit on its side or back
for any reason, allow at least 24 hours before start-up so as to
allow compressor oil to flow back to the sump. Failure to meet
this requirement can cause compressor failure and unit damage.
Unit repairs will not be subject to standard unit
warranties due to improper installation procedures.
Electrical connection
Refer to the amperage data on page 3, the serial tag, your
local code or the National Electrical Code to be sure the unit is
connected to the proper power source. A protected circuit of the
correct voltage and amperage must be run for con­nec­tion of the
line cord, or permanent connection to the unit.
The thermostat must be turned to OFF and
the unit disconnected from the power source
whenever performing service, maintenance
functions or cleaning the refrigerated area.
Power Switch
Select units are equipped with a power disconnect switch
located next to the energy saver switch and thermostat
control knob. Switch must be in the “on” position for the
unit to operate. On freezers, if the switch is turned off, then
returned to the on position, the unit will enter a defrost cycle
and the display will read “Def.”
Upon powering unit, there could be up to a 10
minute delay before unit begins to cool.
Leveling
A level cabinet looks better and will perform better because the
doors will line up with the frames properly, the cabinet will not
be subject to undue strain and the contents of the cabinet will
not move around on the shelves. Use a level to make sure the
unit is level from front to back and side to side. Units supplied
with legs will have adjustable bullet feet to make the necessary
adjustments. If the unit is supplied with casters, no adjustments
are available. Ensure the floor where the unit is to be located
is level.
Delfield
™
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
5
6000XL Series Service and Installation Manual
Door Reversal Procedures
Standard Edge-Mount Hinge
Only for Models Ordered With Re-Hinging Option
1. Open door 90˚ and lift door straight up and off hinges.
2. Remove the metal screw covers on each door-side hinge
section by sliding it down and off.
3. Remove two outer screws that mount each hinge to door,
loosen the center screw, rotate hinge 180˚, reinstall outer
screws and retighten center screw.
4. Remove two screws that mount lock on top of door, turn
door up-side-down and remount lock to top of door.
5. Use a 3/16” drill to drill holes in cabinet face frame at the
marked hinge locations on the new hinge side.
6. Remove the cabinet hinge screw covers by gently prying
them out with a small screwdriver.
7. Remove all three screws from each hinge and mount them
to the opposite side of the door opening.
8. Remove the plastic cam from the hinges by pulling straight
up, then rotating the cam 180˚ and pushing back into the
hinge.
9. Remount the door and check for proper closure and gasket
seal. Adjust hinges as needed. Once adjustment is verified,
remove the door, reinstall all hinge screw covers and set the
door back in place.
10. If plugs are needed to plug old screw holes in cabinet face
frame, please contact Delfield Parts Department at (800)
733-8821, extension 12801.
1. Open door 90˚ and lift door straight up and off hinges.
2. Remove the metal screw covers on each door-side hinge
section by sliding it down and off.
3. Remove two outer screws that mount each hinge to door,
loosen the center screw, rotate hinge 180˚, reinstall outer
screws and retighten center screw.
4. Remove two screws that mount lock on top of door, turn
door up-side-down and remount lock to top of door.
5. Pry the plugs out of the hinge mounting holes on the side
opposite the current hinge locations and set them aside.
6. Remove the cabinet hinge screw covers by gently prying
them out with a small screwdriver.
7. Remove all three screws from each hinge and mount them
to the opposite side of the door opening. Press the plugs
removed in step 5 into the screw holes from the original
hinge locations.
8. Remove the plastic cam from the hinges by pulling straight
up, then rotating the cam 180˚ and pushing back into the
hinge.
9. Remount the door and check for proper closure and gasket
seal. Adjust hinges as needed. Once adjustment is verified,
remove the door, reinstall all hinge screw covers and set the
door back in place.
10. If additional plugs are needed due to loss or damage, please
contact Delfield Parts Department at (800) 733-8821, extension 12801.
Leg & Caster Installation
WARNING
Some cabinets may weigh over 1000 lbs (450 kg).
Use a lifting device capable of supporting the unit
when removing skid or installing legs or casters.
To install the legs, or casters refer to Figure 1 and proceed as
follows:
1. Remove unit from skid.
2. Raise unit to access leg/caster mounting bolts on bottom
of unit.
3. Remove the bolts from the cabinet and use them to attach
the legs or casters.
All single-section units require that the swivel
casters be mounted on the front and rigid casters
be mounted on the rear.
Figure 1. Leg or Caster Installation
Delfield
™
6
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
®
6000XL Series Service and Installation Manual
Operation
Electronic Temperature Control
Operation:
The electronic temperature control constantly monitors box
temperature as well as evaporator coil temperature to maintain
consistent product temperatures. The control also sends
temperature readings to the digital temperature display. The
control circuits continually self-check and if an error occurs,
the digital display will switch from temperature read-out to
error read-out, i.e. E 1. Even when an error is displayed, the
refrigeration and controls system should continue to function,
however not at optimal performance. Whenever the display has
an error read-out, Delfield Service should be contacted.
At initial start-up or anytime power is disconnected, then
reconnected to the unit, the control will delay all operations for
a short time (up to 10 minutes.) While in this delay period, the
control initializes the control parameters and confirms that the
temperature sensors and circuits are operational. The digital
temperature display will not display temperature OR errors until
the self-check is complete and the control has switched on the
evaporator fan motor, compressor and condenser fan motor.
IMPORTANT NOTE REGARDING FREEZERS: After initializing,
the control will immediately enter a DEFROST mode and the
display will read DEF. The compressor and condenser fan as
well as the evaporator fan will remain off until initialization
defrost is complete. This initial defrost cycle may take up to
15 minutes to complete, at which time the freezing cycle will
begin. The display will continue to read DEF for an additional
30 minutes before displaying temperature.
Temperature Alarm:
The alarm will flash “HI” or “LO” 90 minutes after the unit has
reached its alarm temperature point or after any power interruption
if the temperature is above or below the alarm set points.
Refrigerators are factory set at mid-range to maintain about 38ºF
(3ºC) box temperature. The high refrigerator temperature point
is 50°F (10°C). The low refrigerator temperature point is 25°F
(-4°C). Freezers are factory set at mid-range to maintain about 3ºF
(-18ºC) box temperature. The high freezer temperature point is
20°F (-7°C). Freezers do not have a low temperature point.
Refrigerator:
The control is located in the control box in the top of the
refrigerator behind the removable louvered panel on the left
side. It is factory set at mid-range to maintain about 38˚F
(3˚C) box temperature. To adjust for colder temperatures, turn
the knob clockwise. For warmer temperatures, turn the knob
counter-clockwise. Turn the knob fully counter-clockwise to
turn the refrigeration system off. Never turn the knob more
than 1 dial number and always allow 8 hours for temperature
stabilization before making any additional adjustments.
Delfield
™
Freezer:
The control is located in the control box in the top of the
refrigerator behind the removable louvered panel on the left
side. It is factory set at mid-range to maintain about -3˚F
(-18˚C) box temperature. To adjust for colder temperatures,
turn the knob clockwise. For warmer temperatures, turn the
knob counter-clockwise. Turn the knob fully counter-clockwise
to turn the refrigeration system off. Never turn the knob more
than 1 dial number and always allow 8 hours for temperature
stabilization before making any additional adjustments.
Power Switch
Select units are equipped with a power disconnect switch
located next to the energy saver switch and thermostat control
knob. Switch must be in the “on” position for the unit to
operate. On freezers, if the switch is turned off, then returned to
the on position, the unit will enter a defrost cycle and the display
will read “Def.”
Energy Saver Switch
The energy saver switch is a rocker switch located next to
the thermostat knob that controls the amount of heat applied
to the door perimeter. The normal operating position for this
switch is the ON position, providing the least heat. If excessive
condensation is observed on the door opening, press the
energy saver switch to the OFF position, to increase the amount
of heat (red portion of the rocker switch will be visible).
Refrigeration & Defrost Cycle
Refrigerator:
Whenever the refrigerator is plugged in, and the control
has completed initializing, the digital thermostat will display
box temperature. The temperature control will cycle the
compressor, evaporator fan motor and condenser fan motor to
maintain box temperature at the control setting. See evaporator
fan matrix for more information.
Refrigerator Defrost
The temperature control also monitors the evaporator
temperature and will turn off the compressor and condenser
fan motor when needed to allow accumulated frost on the
evaporator to clear. During this defrost cycle, the digital
temperature display will read dEF. After the defrost cycle is
complete, the temperature control will return to a normal
cooling cycle, but the display will continue to read dEF until the
evaporator returns to normal cooling temperatures (up to 30
minutes).
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
7
6000XL Series Service and Installation Manual
Operation, continued
Freezer:
Whenever the freezer is plugged in, and the control has
completed initializing including the initial defrost cycle (also see
Electronic Temperature Control Operation, on this page). The
digital therostat will display box temperature. The temperature
control will cycle the compressor, evaporator fan motor and
condenser fan motor to maintain box temperature at the control
setting. See evaporator fan matrix for more information.
Freezer Automatic Defrost
The control also monitors compressor total running time
and will enter a defrost cycle after total compressor running
time is greater than 4-hours since the last defrost cycle OR
if evaporator coil temperature drops below -30˚F (-34°C)
(indicating excessive frost on the coil).
Freezer Manual Defrost
If a manual defrost is desired, simply unplug the unit for several
seconds, then plug unit back in. This will cause the control to
re-initialize and then enter a defrost cycle.
When the control enters the defrost mode, it switches off the
evaporator fan motor, compressor and condenser fan motor,
and switches on the defrost heater to warm the evaporator
coil. Thereby melting all frost accumulated during the previous
refrigeration cycle. The digital temperature display will now read
dEF. The control will continue the defrost cycle for a MINIMUM
of 8 minutes and a MAXIMUM of 30 minutes depending on the
amount of frost accumulated on the evaporator coil.
After the defrost cycle is complete, the control returns to a normal
refrigeration cycle, however the evaporator fan motor will not
switch on for 2 minutes AFTER the compressor and condenser
fan motor have begun operating. The digital temperature
display will continue to read dEF until the evaporator has
returned to normal freezing temperatures (up to 30 minutes).
Service Alert
During normal operation the evaporator fan may cycle
and/or pulse independently of the compressor. Consult
the service manual or contact Technical Support at
1-800-733-8829 if you are unsure of the proper function.
Evaporator Fan Matrix
Cooling Cycle
Compressor On
Evap Fan On
Refrigerator
X
Freezer
X
Evap Fan Off
Defrost Cycle
Compressor Off
Evap Fan On
Compressor Off
Evap Fan Off
Cycles On 3-Min, Off 3-Min
Evap Fan On
Evap Fan Off
X
X
X
Delfield
™
8
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
®
6000XL Series Service and Installation Manual
Maintenance
The thermostat must be turned to OFF and the unit
disconnected from the power source whenever
performing service, maintenance functions or
cleaning the refrigerated area.
Refrigerators and Freezers
The Delrite® ABS interior and exterior can be cleaned using
soap and warm water. If this isn’t sufficient, try ammonia
and water or a nonabrasive liquid cleaner. When cleaning the
exterior, always rub with the “grain” of the stainless steel to
avoid marring the finish.
Do not use an abrasive cleaner because it will scratch the
stainless steel and plastic and can damage the breaker strips
and gaskets.
Cleaning the Condenser Coil
The condenser coil requires regular cleaning, recommended is
every 90 days. In some instances though you may find that
there is a large amount of debris and dust or grease accumulated
prior to the 90 day time frame. In these cases the condenser coil
should be cleaned every 30 days.
If the build up on the coil consists of only light dust and debris
the condenser coil can be cleaned with a simple brush, heavier
dust build up may require a vacuum or even compressed air to
blow through the condenser coil.
If heavy grease is present there are de-greasing agents available
for refrigeration use and specifically for the condenser coils.
The condenser coil may require a spray with the de-greasing
agent and then blown through with compressed air.
Failure to maintain a clean condenser coil can initially cause high
temperatures and excessive run times, continuous operation
with dirty or clogged condenser coils can result in compressor
failures. Neglecting the condenser coil cleaning procedures will
void any warranties associated with the compressor or cost to
replace the compressor.
Never use a high pressure water wash for this
cleaning procedure as water can damage the
electrical components located near or at the
condenser coil.
In order to maintain proper refrigeration performance, the
condenser fins must be cleaned of dust, dirt and grease regularly.
It is recommended that this be done at least every three months.
If conditions are such that the condenser is totally blocked in
three months, the frequency of cleaning should be increased.
Clean the condenser with a vacuum cleaner or stiff brush. If
extremely dirty, a commercially available condenser cleaner may
be required.
Delfield
™
Stainless Steel Care and Cleaning
To prevent discoloration or rust on stainless steel several
important steps need to be taken. First, we need to understand
the properties of stainless steel. Stainless steel contains 70-80%
iron which will rust. It also contains 12-30% chromium which
forms an invisible passive film over the steels surface which
acts as a shield against corrosion. As long as the protective
layer is intact, the metal is still stainless. If the film is broken
or contaminated, outside elements can begin to breakdown the
steel and begin to form rust of discoloration.
Proper cleaning of stainless steel requires soft cloths or plastic
scouring pads.
NEVER USE STEEL PADS, WIRE BRUSHES OR SCRAPERS!
Cleaning solutions need to be alkaline based or non-chloride
cleaners. Any cleaner containing chlorides will damage
the protective film of the stainless steel. Chlorides are also
commonly found in hard water, salts, and household and
industrial cleaners. If cleaners containing chlorides are used be
sure to rinse repeatedly and dry thoroughly upon completion.
Routine cleaning of stainless steel can be done with soap and
water. Extreme stains or grease should be cleaned with a nonabrasive cleaner and plastic scrub pad. It is always good to
rub with the grain of the steel. There are also stainless steel
cleaners available which can restore and preserve the finish of
the steels protective layer.
Early signs of stainless steel breakdown can consist of small
pits and cracks. If this has begun, clean thoroughly and start to
apply stainless steel cleaners in attempt to restore the passivity
of the steel.
Never use an acid based cleaning solution!
Many food products have an acidic content which
can deteriorate the finish. Be sure to clean the
stainless steel surfaces of ALL food products.
Common items include, tomatoes, peppers and
other vegetables.
Gasket Maintenance
Gaskets require regular cleaning to prevent mold and mildew
build up and also to keep the elasticity of the gasket. Gasket
cleaning can be done with the use of warm soapy water. Avoid
full strength cleaning products on gaskets as this can cause
them to become brittle and prevent proper seals. Also, never
use sharp tools or knives to scrape or clean the gasket which
could possibly tear the gasket and rip the bellows.
Gaskets can easily be replaced and do not require the use of
tools or authorized service persons. The gaskets are “Dart”
style and can be pulled out of the grove in the door and new
gaskets can be “pressed” back into place.
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
9
6000XL Series Service and Installation Manual
Maintenance, continued
Doors/Hinges
Over time and with heavy use doors the hinges may become
loose. If it is noticed that the door is beginning to sag, it may
become necessary to tighten the screws that mount the hinge
brackets to the frame of the unit. If the doors are loose or
sagging this can cause the hinge to pull out of the frame which
may damage both the doors and the door hinges. In some
cases this can require qualified service agents or maintenance
personnel.
Drain Maintenance
Each unit has a drain located inside the unit which removes the
condensation from the evaporator coil and evaporates it at an
external condensate evaporator pan. Each drain can become
loose or disconnected from moving or bumping the drain. If you
notice excessive water accumulation on the inside of the unit be
sure the drain tube is connected from the evaporator housing
to the condensate evaporator drain pan. If water is collected
underneath the unit you may want to check the condensate
evaporator drain tube to be sure it is still located inside the
drain pan. The leveling of the unit is important as the units are
designed to drain properly when on a level surface, if your floor
is not level this can also cause drain problems. Be sure all drain
lines are free of obstructions, typically food product is found
blocking drain lines causing water to back up and overflow the
drain pans.
Fluorescent Light Bulb Replacement
Delfield recommends that fluorescent light bulbs be recycled
rather than disposed of.
Delfield
™
10
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
®
6000XL Series Service and Installation
Manual
REVISIONS
REV
Wiring Diagrams: Refrigerators
9294455
NOTES:
1) USE COPPER CONDUCTORS ONLY
2) THIS UNIT MUST BE GROUNDED
3) UNIT SHOWN WITH COMPRESSOR
RUNNING AND DOORS CLOSED
N
LINE VOLTAGE
115/60/1
SEE NAMEPLATE FOR MAXIMUM
FUSE SIZE
L ENNIS
3
BROWN COMPRESSOR WIRE WAS BLACK (ON DIAGRAM ONLY)
26-MAY-2011
L ENNIS
M
Y
N
5
BLUE
F
M
6
FAN RELAY
PLUG
DEFROST
HEATER
EVAP COIL
SENSOR
CONTROL
CIRCUIT
W
EVAPORATOR FAN
INCANDESCENT
LIGHT
H
4
HEATER
RELAY
C
M
COMPRESSOR
W
WITH BLUE
STRIPES
W
CONTROL
BOX
1
COMPRESSOR
RELAY
ENERGY SAVER
SWITCH
WIRE
NUT
W
P
1.1,2,3 2.1,2,3 3.1,2,3
SPLICE
BLK
CONDENSOR FAN
CABINET AIR
SENSOR
EVAP COIL
SENSOR
8 21 "
W
M
LED DISPLAY
(IF USED)
17-MAY-2011
EVAP FAN
MOTOR
CABINET AIR
SENSOR
L
DESCRIPTION
EVAPORATOR HOUSING
TEMPERATURE
CONTROL
2/3
APPROVED
INITIAL RELEASE
ADDED L-2/3 DESIGNATION & H-4 FOR HEATER TERMINAL
11"
6025XL-S, 6025XL-SH
L1
DATE
1
2
POWER BOX
GREY
START RELAY
BRN
10
BLK
W
RED
C L L H N F
1 2 3 4 5 6
TEMPERATURE
CONTROL
BLK
12
W
N
RU ING
D
DOOR FRAME
HEATER
WIN
ENERGY SAVER
SWITCH
START
CAPACITOR
11
CONDENSER
FAN
M
RT G
STA INDIN 13
W
COMPRESSOR
GROUND
14
MOTOR PROTECTOR
1.1,2,3 2.1,2,3 3.1,2,3
DOOR
SWITCH
INCANDESCENT
LIGHT
BLK
DOOR
HINGE
SWITCH
BLK
LED DISPLAY
(IF USED)
W
COMPRESSOR
REVISIONS
FRAME HEATERS
REV
PROPRIETARY
6025XL-G, 6025XL-GH
UNLESS OTHERWISE SPECIFIED
11"
.X ±
.XX ±
.XXX ±
ANG. ±
MATERIAL
BLK
9294475
L1
N
LINE VOLTAGE
115/60/1
SEE NAMEPLATE FOR MAXIMUM
FUSE SIZE
02-MAY-2011
L EN
ADDED L-2/3 DESIGNATION & H-4 FOR HEATER TERMINAL
17-MAY-2011
L EN
3
SIGNATURE
DATE
BROWN
COMPRESSOR WIRE
WAS BLACK (ON DIAGRAM ONLY)
26-MAY-2011
L EN
11/11/10
CHECKED:
.1
.03
.010
1
EN
Reach-in Divison
COVINGTON,
DESCRIPTION
LABEL, WIRING, 1 DR, SPEC/6000XL
REFRIGERATOR, ENERGY STAR
MFG:
PURCH:
SIZE
C
QA:
THIRD ANGLE
PROJECTION
LOCATION
DWG. NO.
9294455
SCALE
DO NOT SCALE DRAWING
SHEET
1 OF
RE
1
BLUE
RED
BLK
APPR
INITIAL RELEASE
MGC
ALL PARTS TO BE DEBURRED AND EDGES
BROKEN .010 MAXIMUM.
FLUORESCENT LIGHT
BALLAST
FLUORESCENT
LAMP
SWITCH
DATE
1
2
DRAWN:
DIMENSIONS ARE IN INCHES
TOLERANCES
The contents of this document are
PROPRIETARY TO THE DELFIELD COMPANY
and are not to be disclosed to others
or used for purposes other than
intended without the written approval
of The Delfield Company.
DESCRIPTION
FLUORESCENT LAMP
W
FLUORESCENT LAMP ASSEMBLY
TEMPERATURE
CONTROL
N
CONTROL
CIRCUIT
2/3
EVAPORATOR HOUSING
5
F
6
FAN RELAY
EVAP FAN
MOTOR
M
CABINET AIR
SENSOR
C
M
1
COMPRESSOR
RELAY
COMPRESSOR
CONTROL
BOX
1.1,2,3 2.1,2,3 3.1,2,3
EVAP COIL
SENSOR
CABINET AIR
SENSOR
M
LED DISPLAY
(IF USED)
Y
BLUE
4
HEATER
RELAY
CONDENSOR FAN
PLUG
M
EVAPORATOR FAN
H
EVAP COIL
SENSOR
L
W
BLK
ENERGY SAVER
SWITCH
W
W
WITH BLUE
STRIPES
WIRE
NUT
8 21 "
W
P
W
SPLICE
BLK
POWER BOX
W
GREY
BRN
ENERGY SAVER
SWITCH
DOOR FRAME
HEATER
FLUORESCENT
LAMP BALLAST
12
CONDENSER
FAN MOTOR
1.1,2,3 2.1,2,3 3.1,2,3
R G
STA INDIN 13
W
14
Delfield1.NOTES:
STRIP-TAC ADHESIVE BACKING
™
BLK
W
LED DISPLAY
(IF USED)
BLK
COMPRESSOR
FRAME HEATERS
®
2. BLACK PRINT ON WHITE PAPER
COMPRESSOR
GROUND
MOTOR PROTECTOR
M
NOTES:
1) USE COPPER CONDUCTORS ONLY
2) THIS UNIT MUST BE GROUNDED
3) UNIT SHOWN WITH COMPRESSOR
RUNNING AND DOORS CLOSED
START
CAPACITOR
11
BLK
N
RU ING
D
FLUORESCENT
LAMP
10
WIN
FLUORESCENT
LAMP SWITCH
START RELAY
W
W
C L L H N F
1 2 3 4 5 6
TEMPERATURE
CONTROL
PROPRIETARY
The contents of this document are
PROPRIETARY TO THE DELFIELD COMPANY
and are not to be disclosed to others
or used for purposes other than
intended without the written approval
of The Delfield Company.
SIGNATURE
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
TOLERANCES
DRAWN:
L ENNIS
DATE
15-APR-2011
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
MATERIAL
.X ±
.XX ±
.XXX ±
ANG. ±
.1
.03
.010
1
ALL PARTS TO BE DEBURRED AND EDGES
BROKEN .010 MAXIMUM.
THIRD ANGLE
PROJECTION
CHECKED:
MFG:
PURCH:
DESCRIPTION
SIZE
C
QA:
DO NOT SCALE DRAWING
Reach-in Divison
11
CO
LABEL,WIRING,1DR,REF,GL
DR,SPECLINE/6000XL,ESTAR
SCALE
LOCATION
DWG. NO.
9294475
SHEET
1 OF
1
6000XL Series Service and Installation Manual
REVISIONS
REV
Wiring Diagrams: Refrigerators
9294454
NOTES:
1) USE COPPER CONDUCTORS ONLY
2) THIS UNIT MUST BE GROUNDED
3) UNIT SHOWN WITH COMPRESSOR
RUNNING AND DOORS CLOSED
N
LINE VOLTAGE
115/60/1
SEE NAMEPLATE FOR MAXIMUM
FUSE SIZE
17-MAY-2011
L ENNIS
3
BROWN COMPRESSOR WIRE WAS BLACK (ON DIAGRAM ONLY)
26-MAY-2011
L ENNIS
M
Y
N
5
BLUE
F
M
6
FAN RELAY
PLUG
DEFROST
HEATER
EVAP COIL
SENSOR
CONTROL
CIRCUIT
W
EVAPORATOR FAN
INCANDESCENT
LIGHT
H
4
HEATER
RELAY
C
M
COMPRESSOR
W
WITH BLUE
STRIPES
W
CONTROL
BOX
1
COMPRESSOR
RELAY
ENERGY SAVER
SWITCH
8 21 "
W
M
SPLICE
BLK
CONDENSOR FAN
CABINET AIR
SENSOR
EVAP COIL
SENSOR
WIRE
NUT
W
P
1.1,2,3 2.1,2,3 3.1,2,3
LED DISPLAY
(IF USED)
ADDED L-2/3 DESIGNATION & H-4 FOR HEATER TERMINAL
EVAP FAN
MOTOR
CABINET AIR
SENSOR
L
APPROVED
INITIAL RELEASE
EVAPORATOR HOUSING
TEMPERATURE
CONTROL
2/3
DATE
1
2
11"
6051XL-S, 6051XL-SH
L1
DESCRIPTION
W
POWER BOX
GREY
BRN
ENERGY SAVER
SWITCH
10
C L L H N F
1 2 3 4 5 6
TEMPERATURE
CONTROL
BLK
DOOR FRAME
HEATERS
START RELAY
BLK
W
RED
START
CAPACITOR
11
W
12
M
N
RU ING
D
WIN
CONDENSER
FAN
1.1,2,3 2.1,2,3 3.1,2,3
R G
STA INDIN 13
W
COMPRESSOR
GROUND
14
MOTOR PROTECTOR
INCANDESCENT
LIGHT
DOOR
SWITCHES
LED DISPLAY
(IF USED)
W
BLK
DOOR
HINGE
SWITCHES
BLK
COMPRESSOR
DOOR FRAME HEATERS
PROPRIETARY
MATERIAL
BLK
9294476
L1
N
LINE VOLTAGE
115/60/1
SEE NAMEPLATE FOR MAXIMUM
FUSE SIZE
BLK
FLUORESCENT LAMP
W
CONTROL
CIRCUIT
2/3
6
LOCATION
C
DO NOT SCALE DRAWING
FLUORESCENT LIGHT
BALLAST
DWG. NO.
9294454
SCALE
SHEET
1 OF
1
BLUE
FLUORESCENT LAMP
W
EVAP FAN
MOTOR
Y
M
1
COMPRESSOR
CONTROL
BOX
W
BLK
ENERGY SAVER
SWITCH
CONDENSOR FAN
EVAP COIL
SENSOR
CABINET AIR
SENSOR
BLUE
CABINET AIR
SENSOR
PLUG
M
4
M
EVAP COIL
SENSOR
SIZE
EVAPORATOR HOUSING
M
EVAPORATOR FAN
1.1,2,3 2.1,2,3 3.1,2,3
LED DISPLAY
(IF USED)
PURCH:
N
C
COMPRESSOR
RELAY
COVINGT
FLUORESCENT LAMP ASSEMBLY
H
HEATER
RELAY
26-MAY-2011
Reach-in Divison
DESCRIPTION
LABEL,WIRING,2 DR,SPEC/6000XL,
REFRIGERATOR, ENERGY STAR
RED
BLK
5
F
FAN RELAY
11/11/10
QA:
FLUORESCENT LAMP ASSEMBLY
TEMPERATURE
CONTROL
L
17-MAY-2011
MFG:
FLUORESCENT
LAMP
SWITCH
BLUE
RED
ADDED HEATER RELAY TO CONTROL & L-2/3 DESIGNATION
CHECKED:
ALL PARTS TO BE DEBURRED AND EDGES
BROKEN .010 MAXIMUM.
FLUORESCENT LIGHT
BALLAST
FLUORESCENT
LAMP
SWITCH
02-MAY-2011
2
MGC
.1
.03
.010
1
THIRD ANGLE
BLK
PROJECTION
DATE
INITIAL RELEASE
DRAWN:
DIMENSIONS ARE IN INCHES
TOLERANCES
.X ±
.XX ±
.XXX ±
ANG. ±
DESCRIPTION
1
SIGNATURE
DATE WIRE WAS BLACK (ON DIAGRAM ONLY)
3 BROWN COMPRESSOR
UNLESS OTHERWISE SPECIFIED
The contents of this document are
PROPRIETARY TO THE DELFIELD COMPANY
and are not to be disclosed to others
or used for purposes other than
intended without the written approval
of The Delfield Company.
11"
6051XL-G, 6051XL-GH
REVISIONS
REV
W
W
WITH BLUE
STRIPES
WIRE
NUT
W
P
8 21 "
W
SPLICE
BLK
W
POWER BOX
GREY
BRN
ENERGY SAVER
SWITCH
DOOR FRAME
HEATERS
FLUORESCENT
LAMP BALLAST
FLUORESCENT
LAMP
W
C L L H N F
1 2 3 4 5 6
TEMPERATURE
CONTROL
12
CONDENSER
FAN MOTOR
1.1,2,3 2.1,2,3 3.1,2,3
FLUORESCENT
12
BLK
R G
STA INDIN 13
W
14
COMPRESSOR
GROUND
MOTOR PROTECTOR
M
FLUORESCENT
LAMP BALLAST
LAMP
NOTES:
1) USE COPPER CONDUCTORS ONLY
2) THIS UNIT MUST BE GROUNDED
3) UNIT SHOWN WITH COMPRESSOR
RUNNING AND DOORS CLOSED
START
CAPACITOR
11
BLK
N
RU ING
D
WIN
FLUORESCENT
LAMP SWITCHES
START RELAY
10
W
W
LED DISPLAY
(IF USED)
BLK
COMPRESSOR
DOOR FRAME HEATERS
NOTES:
1. STRIP-TAC ADHESIVE BACKING
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
2. BLACK PRINT ON WHITE PAPER
PROPRIETARY
The contents of this document are
PROPRIETARY TO THE DELFIELD COMPANY
and are not to be disclosed to others
or used for purposes other than
intended without the written approval
of The Delfield Company.
MATERIAL
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
TOLERANCES
.X ±
.XX ±
.XXX ±
ANG. ±
.1
.03
.010
1
ALL PARTS TO BE DEBURRED AND EDGES
BROKEN .010 MAXIMUM.
THIRD ANGLE
PROJECTION
Delfield
™
SIGNATURE
DRAWN:
L ENNIS
CHECKED:
DATE
02-MAY-2011
MFG:
PURCH:
LABEL,WIRING,2DR,REF,GL
DR,SPECLINE/6000XL,ESTAR
SIZE
C
QA:
DO NOT SCALE DRAWING
Rea
®
DESCRIPTION
SCALE
LOCATION
DWG. NO.
9294476
SHEET
1 OF
1
REVISIONS
6000XL Series Service and Installation Manual
REV
DESCRIPTION
INITIAL RELEASE
1
Wiring Diagrams: Refrigerators
DATE
APPROVE
02-MAY-2011
L ENNIS
2
ADDED L-2/3 DESIGNATION & H-4 FOR HEATER TERMINAL
17-MAY-2011
L ENNIS
3
BROWN COMPRESSOR WIRE WAS BLACK (ON DIAGRAM ONLY)
26-MAY-2011
L ENNIS
DATE
APPROVE
11"
6076XL-S, 6076XL-SH
9294477
L1
NOTES:
1) USE COPPER CONDUCTORS ONLY
2) THIS UNIT MUST BE GROUNDED
3) UNIT SHOWN WITH COMPRESSOR
RUNNING AND DOORS CLOSED
N
LINE VOLTAGE
115/60/1
SEE NAMEPLATE FOR MAXIMUM
FUSE SIZE
TEMPERATURE
CONTROL
L
CONTROL
CIRCUIT
2/3
RECEPTICAL BOX
F
FAN RELAY
PLUG
N
5
M
6
EVAPORATOR FAN
H
4
HEATER
RELAY
C
COMPRESSOR
RELAY
M
1
COMPRESSOR
1.1,2,3 2.1,2,3 3.1,2,3
CABINET AIR
SENSOR
ENERGY SAVER
SWITCH
DOOR FRAME
HEATER
EVAPORATOR HOUSING
DOOR
SWITCH
TEMPERATURE
CONTROL
M
Y
BLUE
M
6
BLUE
W
INCANDESCENT
LIGHT
EVAPORATOR FAN
H
INCANDESCENT
LIGHT
4
HEATER
RELAY
M
CONTROL
BOX
COMPRESSOR
P
C
COMPRESSOR
RELAY
1
W
ENERGY SAVER
SWITCH
W
WITH BLUE
STRIPES
CABINET AIR
SENSOR
EVAP COIL
SENSOR
ENERGY SAVER
SWITCH
WIRE
NUT
W
W
SPLICE
CONDENSOR FAN
12
CONTROL
DOOR FRAME
HEATERS
M
N
RU ING
D
WIN
W
CONDENSER
FAN
BRN
START
CAPACITOR
RED
14
10
C L L H N F
1 2 3 4 5 6
TEMPERATURE
BLK
COMPRESSOR
GROUND
START RELAY
BLK
W
RT G
STA INDIN 13
W
POWER BOX
GREY
START RELAY
11
BLK
W
C L L H N F
1 2 3 4 5 6
TEMPERATURE
BLK
W
POWER BOX
BRN
RED
SPLICE
BLK
GREY
10
START
CAPACITOR
11
W
CONTROL
12
M
R G
STA INDIN 13
W
MOTOR PROTECTOR
N
RU ING
D
WIN
1.1,2,3 2.1,2,3 3.1,2,3
DOOR
SWITCHES
W
WITH BLUE
STRIPES
P
BLK
M
ENERGY SAVER
SWITCH
W
CONTROL
BOX
WIRE
NUT
W
W
1.1,2,3 2.1,2,3 3.1,2,3
LED DISPLAY
(IF USED)
8 21 "
Y
W
CABINET AIR
SENSOR
N
5
F
FAN RELAY
EVAP FAN
MOTOR
M
EVAP COIL
SENSOR
CONTROL
CIRCUIT
CABINET AIR
SENSOR
L
2/3
EVAPORATOR HOUSING
EVAP FAN
MOTOR
INCANDESCENT
LIGHT
EVAP COIL
SENSOR
EVAP COIL
SENSOR
LED DISPLAY
(IF USED)
M
CONDENSOR FAN
CONDENSER
FAN
1.1,2,3 2.1,2,3 3.1,2,3
14
COMPRESSOR
GROUND
MOTOR PROTECTOR
BLK
INCANDESCENT
LIGHT
DOOR
HINGE
SWITCH
BLK
LED DISPLAY
(IF USED)
W
COMPRESSOR
W
BLK
DOOR
HINGE
SWITCHES
LED DISPLAY
(IF USED)
BLK
REVISIONS
COMPRESSOR
DOOR FRAME HEATERS
FRAME HEATERS
6076XL-G,
L1
NOTES:
1. STRIP-TAC ADHESIVE BACKING
2. BLACK PRINT ON WHITE PAPER
6076XL-GH
N
LINE VOLTAGE
115/60/1
SEE NAMEPLATE FOR MAXIMUM
FUSE SIZE
TEMPERATURE
CONTROL
CONTROL
CIRCUIT
2/3
N
5
F
FAN RELAY
6
PROPRIETARY
UNLESS OTHERWISE SPECIFIED
11"
1
INITIAL RELEASE
02-MAY-2011
L ENNIS
ADDED HEATER RELAY TO CONTROL & L-2/3 DESIGNATION
SIGNATURE
DATE
BROWNDRAWN:
COMPRESSOR WIRE WAS BLACK (ON DIAGRAM ONLY)
L ENNIS
05-MAY-2011
17-MAY-2011
L ENNIS
DIMENSIONS ARE IN INCHES 3
TOLERANCES
The contents of this document are
PROPRIETARY TO THE DELFIELD COMPANY
and are not to be disclosed to others
or used for purposes other than
intended without the written approval
of The Delfield Company.
.X ±
.XX ±
.XXX ±
ANG. ±
MATERIAL
NOTES:
1) USE COPPER CONDUCTORS ONLY
2) THIS UNIT MUST BE GROUNDED
3) UNIT SHOWN WITH COMPRESSOR
RUNNING AND DOORS CLOSED
DESCRIPTION
2
.1
.03
.010
1
CHECKED:
COVING
LABEL,WIRING,3DR,REF,
6000XL,ESTAR
PURCH:
ALL PARTS TO BE DEBURRED AND EDGES
BROKEN .010 MAXIMUM.
26-MAY-2011 Reach-in Divison
L ENNIS
DESCRIPTION
MFG:
SIZE
C
QA:
THIRD ANGLE
PROJECTION
9294478
L
REV
LOCATION
DWG. NO.
9294477
SCALE
DO NOT SCALE DRAWING
SHEET
1 OF
1
PLUG
RECEPTICAL BOX
M
EVAPORATOR FAN
H
4
C
M
1
BLK
COMPRESSOR
CABINET AIR
SENSOR
CONDENSOR FAN
BLK
BLK
FLUORESCENT LAMP
W
FLUORESCENT
LAMP SWITCH
6
EVAPORATOR FAN
BLUE
BLUE
COMPRESSOR
BLK
CONTROL
BOX
W
ENERGY SAVER
SWITCH
W
WITH BLUE
STRIPES
BLK
WIRE
NUT
W
CABINET AIR
SENSOR
P
EVAP COIL
SENSOR
W
M
1
M
CONTROL
BOX
W
WITH BLUE
STRIPES
WIRE
NUT
W
W
SPLICE
BLK
12
CONDENSER
FAN
14
START
CAPACITOR
10
C L L H N F
1 2 3 4 5 6
TEMPERATURE
CONTROL
COMPRESSOR
GROUND
12
W
M
MOTOR PROTECTOR
1.1,2,3 2.1,2,3 3.1,2,3
CONDENSER
FAN
RT G
STA INDIN 13
W
COMPRESSOR
GROUND
14
MOTOR PROTECTOR
1.1,2,3 2.1,2,3 3.1,2,3
FLUORESCENT
LAMP
FLUORESCENT
LAMP BALLAST
BLK
BLK
START
CAPACITOR
11
BLK
W
N
RU ING
D
M
RT G
STA INDIN 13
W
START RELAY
BRN
WIN
WIN
W
N
RU ING
D
C L L H N F
1 2 3 4 5 6
TEMPERATURE
CONTROL
FLUORESCENT
LAMP BALLAST
11
BLK
W
POWER BOX
GREY
START RELAY
10
DOOR FRAME
HEATERS
SPLICE
BLK
POWER BOX
BRN
FLUORESCENT
LAMP SWITCHES
W
ENERGY SAVER
SWITCH
P
W
CONDENSOR FAN
GREY
ENERGY SAVER
SWITCH
Y
P
W
1.1,2,3 2.1,2,3 3.1,2,3
LED DISPLAY
(IF USED)
M
Y
P
M
4
C
COMPRESSOR
RELAY
EVAP FAN
MOTOR
M
N
8 21 "
EVAPORATOR HOUSING
EVAP FAN
MOTOR
H
HEATER
RELAY
FLUORESCENT LAMP ASSEMBLY
EVAPORATOR HOUSING
5
F
FAN RELAY
FLUORESCENT LAMP ASSEMBLY
EVAP COIL
SENSOR
CONTROL
CIRCUIT
FLUORESCENT LAMP
W
EVAP COIL
SENSOR
L
2/3
W
BLUE
RED
BLK
FLUORESCENT
LAMP
TEMPERATURE
CONTROL
FLUORESCENT LIGHT
BALLAST
FLUORESCENT
LAMP
SWITCH
BLUE
RED
FLUORESCENT
LAMP BALLAST
FLUORESCENT LAMP
W
BLK
FLUORESCENT LIGHT
BALLAST
FLUORESCENT
LAMP
SWITCH
DOOR FRAME
HEATER
BLUE
RED
BLK
CABINET AIR
SENSOR
EVAP COIL
SENSOR
LED DISPLAY
(IF USED)
M
ENERGY SAVER
SWITCH
FLUORESCENT LIGHT
BALLAST
FLUORESCENT
LAMP
SWITCH
1.1,2,3 2.1,2,3 3.1,2,3
CABINET AIR
SENSOR
HEATER
RELAY
COMPRESSOR
RELAY
W
LED DISPLAY
(IF USED)
BLK
COMPRESSOR
BLK
W
LED DISPLAY
(IF USED)
COMPRESSOR
FLUORESCENT
LAMP
DOOR FRAME HEATER
NOTES:
1. STRIP-TAC ADHESIVE BACKING
2. BLACK PRINT ON WHITE PAPER
Delfield
™
®
DOOR FRAME HEATERS
PROPRIETARY
The contents of this document are
PROPRIETARY TO THE DELFIELD COMPANY
and are not to be disclosed to others
or used for purposes other than
intended without the written approval
of The Delfield Company.
SIGNATURE
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
TOLERANCES
.X ±
.XX ±
.XXX ±
ANG. ±
.1
.03
.010
1
DRAWN:
L ENNIS
CHECKED:
DATE
05-MAY-2011
Reach-in Divison
DESCRIPTION
COVING
13
LABEL,WIRING,3DR,REF,GL DR,
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
6000XL,ESTAR
MATERIAL
ALL PARTS TO BE DEBURRED AND EDGES
BROKEN .010 MAXIMUM.
THIRD ANGLE
PROJECTION
MFG:
PURCH:
SIZE
C
QA:
DO NOT SCALE DRAWING
SCALE
LOCATION
DWG. NO.
9294478
SHEET
1 OF
1
6000XL Series Service and Installation Manual
Wiring Diagrams: Freezers
6125XL-S, 6125XL-SH
Delfield
™
14
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
®
6000XL Series Service and Installation Manual
Wiring Diagrams: Freezers
6151XL-S, 6151XL-SH
9294124
L1
N
LINE VOLTAGE
115/60/1
SEE NAMEPLATE FOR MAXIMUM
FUSE SIZE
NOTES:
1) USE COPPER CONDUCTORS ONLY
2) THIS UNIT MUST BE GROUNDED
3) UNIT SHOWN WITH COMPRESSOR
RUNNING AND DOORS CLOSED
EVAPORATOR HOUSING
EVAP FAN
MOTOR
POWER SWITCH
Y
N
5
BLUE
F
M
6
FAN RELAY
PLUG
DEFROST
HEATER
EVAP COIL
SENSOR
CONTROL
CIRCUIT
3
CABINET AIR
SENSOR
L
HIGH TEMP
LIMIT
SWITCH
M
TEMPERATURE
CONTROL
W
EVAPORATOR FAN
INCANDESCENT
LIGHT
H
4
HEATER RELAY
C
M
CONTROL
BOX
1
COMPRESSOR
RELAY
COMPRESSOR
W
POWER SWITCH
W
WITH BLUE
STRIPES
WIRE
NUT
W
P
1.1,2,3 2.1,2,3 3.1,2,3
W
EVAP COIL
SENSOR
CABINET AIR
SENSOR
M
LED DISPLAY
(IF USED)
POWER BOX
DEFROST HEATER
ENERGY SAVER
SWITCH
CONDENSOR FAN
SPLICE
BLK
GREY
W
BRN
ENERGY SAVER
SWITCH
C L L H N F
1 2 3 4 5 6
TEMPERATURE
CONTROL
BLK
DOOR FRAME
HEATERS
W
CONDENSER
FAN
LED DISPLAY
(IF USED)
W
BLK
R
5
2
4
1
START
WINDING
INCANDESCENT
LIGHT
DOOR
HINGE
SWITCHES
RUN CAPACITOR
S
M
1.1,2,3 2.1,2,3 3.1,2,3
DOOR
SWITCHES
MAIN WINDING
C
BLK
W
RED
MOTOR
PROTECTOR
BLK
1
1
2
2
N
N
L
L
START CAPACITOR
COMPRESSOR
DOOR FRAME HEATERS
6176XL-S, 6176XL-SH
NOTES:
1) USE COPPER CONDUCTORS ONLY
2) THIS UNIT MUST BE GROUNDED
3) UNIT SHOWN WITH COMPRESSOR
RUNNING AND DOORS CLOSED
9294127
L2
EVAP FAN
MOTOR
C
1
M
EVAPORATOR FAN
FAN RELAY
DEFROST HEATER
DEFROST HEATER
M
M
H
4
HEATER RELAY
C
COMPRESSOR
COMPRESSOR
M
M
CONDENSOR FAN
CONDENSOR FAN
W
DOOR FRAME
HEATER
DOOR
SWITCH
INCANDESCENT
LIGHT
Delfield
™
WIRE
NUT
BLK
W
BLK
C L L H N F
1 2 3 4 5 6
TEMPERATURE
CONTROL
W
CONDENSER
FAN
ENERGY SAVER
SWITCH
DOOR
SWITCHES
DOOR
HINGE
SWITCH
BLK
W
FRAME HEATERS
LED DISPLAY
(IF USED)
BLK
CABINET AIR
SENSOR
W
W
WITH BLUE
STRIPES
W
MOTOR
PROTECTOR
C
RUN CAPACITOR
5
2
4
1
START
WINDING
1
2
N
L
1
2
N
L
BLK
W
RED
BLK
C L L H N F
1 2 3 4 5 6
TEMPERATURE
CONTROL
W
CONDENSER
FAN
START CAPACITOR
COMPRESSOR
BLK
W
DOOR FRAME HEATERS
LED DISPLAY
(IF USED)
MOTOR
PROTECTOR
C
S
M
1.1,2,3 2.1,2,3 3.1,2,3
DOOR
HINGE
SWITCHES
POWER BOX
W
BRN
MAIN WINDING
R
SPLICE
BLK
ENERGY SAVER
SWITCH
GREY
POWER BOX
WIRE
NUT
W
P
S
M
W
POWER SWITCH
SPLICE
W
GREY
RED
CONTROL
BOX
W
W
BRN
INCANDESCENT
LIGHT
DEFROST
HEATER
INCANDESCENT
LIGHT
BLK
ENERGY SAVER
SWITCH
1
COMPRESSOR
RELAY
1.1,2,3 2.1,2,3 3.1,2,3
DOOR FRAME
HEATERS
BLUE
W
WITH BLUE
STRIPES
P
1.1,2,3 2.1,2,3 3.1,2,3
ENERGY SAVER
SWITCH
W
INCANDESCENT
LIGHT
CONTROL
BOX
CABINET AIR
SENSOR
H
4
F
6
M
EVAPORATOR FAN
LED DISPLAY
(IF USED)
LED DISPLAY
(IF USED)
EVAP COIL
SENSOR
COMPRESSOR
RELAY
1.1,2,3 2.1,2,3 3.1,2,3
F
6
DEFROST
HEATER
L
3
CONTROL
CIRCUIT
EVAP COIL
SENSOR
HEATER RELAY
N
5
CABINET AIR
SENSOR
FAN RELAY
BLUE
Y
EVAP COIL
SENSOR
POWER SWITCH
TEMPERATURE
CONTROL
HIGH TEMP
LIMIT
SWITCH
M
Y
N
N
5
EVAP FAN
MOTOR
HIGH TEMP
LIMIT
SWITCH
M
TEMPERATURE
CONTROL
CONTROL
CIRCUIT
EVAPORATOR HOUSING
EVAPORATOR HOUSING
EVAP COIL
SENSOR
LINE VOLTAGE
115/208-230/60/1
SEE NAMEPLATE FOR MAXIMUM
FUSE SIZE
L
3
RECEPTICAL BOX
CABINET AIR
SENSOR
L1
NEMA 14-20P PLUG
BLK
MAIN WINDING
RUN CAPACITOR
R
5
2
4
1
START
WINDING
1
2
N
L
1
2
N
L
START CAPACITOR
COMPRESSOR
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
15
6000XL Series Service and Installation Manual
Refrigeration Package Diagram
17
16
4
7
15
18
5
12
6
14
11
9
1
3
8
21
13
9
14
11
7
1
15
16
4
5
6
17
21
19
20
3
2
18
Delfield
™
16
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
®
6000XL Series Service and Installation Manual
Refrigeration Package - Replacement Parts
Refrigerator - 1 section & 3 section left package
Item Number
Part Number
1
2 (kit)
3
4
5
6
7
8
9
11
12
13
14
15
15
16
16
17
17
18
3516437
2194811KT
2190154
2184181
2162715
3517390
3516429
3516205
3516427
127-C33-0036
2162717
3516432
2160019
3526999
220V/50Hz
Part#
2194988KT
2162719
2192720
3527013
3516444
117U6002
2194787
117U5015
3516322
1702795
3516041
Freezer- 1 section & 3 section left package
Description
Coil, evaporator
Temperature Control
Switch, energy saver
Cord, power
Motor, fan, evaporator
Fan blade, evaporator
Valve, refrigerant, TXV
Clip, TXV bulb mounting
Coil, condenser
Shroud, condenser fan
Motor, fan, condenser, 9W
Fan blade, condenser
Guard, condenser fan
Compressor
Compressor, 50Hz - NL7CUX
Relay & overload, compressor
50Hz Relay and overload, Danfoss p/n
Capacitor, compressor start, 280MFD
50Hz Capacitor, start, 80MFD, Danfoss p/n
Filter-drier, refrigerant
Condensate pan
Solenoid valve, used on remote units
Refrigerator - 2 section & 3 section right package
Item Number
Part Number
1
2 (kit)
3
4
5
6
7
8
9
11
12
13
14
15
15
16
16
17
17
18
3516437
2194811KT
2190154
2184181
2162715
3517390
3516429
3516205
3516427
127-C33-0030
2162716
3516433
2160019
3527000
220V/50Hz
Part#
2194988KT
2192719
2162721
3527012
3516438
117U6003
2194788
117U5015
3516322
1702795
3516041
Delfield
™
Item
Number
1
2 (kit)
3
4
5
6
7
8
9
11
12
13
14
15
15
16
16
17
17
18
19
20
21
Part Number
3516436
2194812KT
2194959
2184181
2162715
3517390
3516588
3516205
3516427
127-C33-0036
2162717
3516432
2160019
3527001
220V/50Hz
Part#
2194964KT
2194183
2162719
2162720
3527011
3516441
117U6019
2194789
117U5017
3516322
2194785
9321629
2194953
1702795
3516041
2194967
Description
Coil, evaporator
Control, ETC1, Kit
Switch, SPDT, energy saver
Cord, power
Motor, fan, evaporator
Fan blade, evaporator
Valve, refrigerant, TXV
Clip, TXV bulb mounting
Coil, condenser
Shroud, condenser fan
Motor, fan, condenser, 9W
Fan blade, condenser
Guard, condenser fan
Compressor
Compressor, 50 Hz - NL8.4CLX danfoss
Relay & overload, compressor
50Hz Relay and overload, Danfoss p/n
Capacitor, compressor start, 240MFD
50Hz Capacitor, start, 80MFD, Danfoss p/n
Filter-drier, refrigerant
Heater, defrost
Clip, defrost heater mounting
Switch, defrost safety, high limit
Condensate pan
Solenoid valve, used on remote units
Freezer- 2 section & 3 section right package
Description
Coil, evaporator
Temperature Control
Switch, energy saver
Cord, power
Motor, fan, evaporator
Fan blade, evaporator
Valve, refrigerant, TXV
Clip, TXV bulb mounting
Coil, condenser
Shroud, condenser fan
Motor, fan, condenser, 16W
Fan blade, condenser
Guard, condenser fan
Compressor, Kit
Compressor, 50Hz - SC15CLX.2 danfoss
Relay & overload, compressor
50Hz Relay and overload, Danfoss p/n
Capacitor, compressor start, 320MFD
50Hz Capacitor, start, 80MFD, Danfoss p/n
Filter-drier, refrigerant
Condensate pan
Solenoid valve, used on remote units
Item
Number
1
2 (kit)
3
4
5
6
7
8
9
11
12
13
14
15
15
16
16
17
18
19
20
21
Part Number
3516436
2194812KT
2194959
2190154
2184181
2162715
3517390
3516588
3516205
3516427
127-C33-0030
2162716
3516433
2160019
3527002
220V/50Hz Part#
2194964KT
2194183
2162719
2162721
3527010
3516468
117U6013
117U5012
3516322
2194785
9321629
2194953
1702795
3516041
2194967
Description
Coil, evaporator
Control, ETC1, Kit
Switch, SPDT, energy saver
Switch, SPST, ON/OFF
Cord, power
Motor, fan, evaporator
Fan blade, evaporator
Valve, refrigerant, TXV
Clip, TXV bulb mounting
Coil, condenser
Shroud, condenser fan
Motor, fan, condenser, 16W
Fan blade, condenser
Guard, condenser fan
Compressor, Kit
Compressor, 50Hz - Sc18CLX.2, danfoss
Relay and capacitor, compressor start, 125MFD
50Hz Relay, Danfoss p/n
50Hz Capacitor, start, 125MFD, Danfoss p/n
Filter-drier, refrigerant
Heater, defrost
Clip, defrost heater mounting
Switch, defrost safety, high limit
Condensate pan
Solenoid valve, used on remote units
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
17
6000XL Series Service and Installation Manual
Replacement Parts
Miscellaneous Replacement Parts
Part Number
2194791
3235514
3234778
3234779
2194792
3239590
3234791
3978270
3978277
3978278
Description
Cable
Casters, rigid, One section only
Casters, swivel, w/o brake, Two & Three section
Casters, swivel, with brake
Display
Door lock
Legs
Shelf, One Section, Three Section
Shelf LH, Two Section, Three Section
Shelf RH, Two Section, Three Section
5066440
3516204A
Switch, rocker, door, SPDT-D8
Vacuum breaker
Stainless Steel Door Replacement Parts
Part Number
Description
2194005
Bulb, incandescent, 40W
2194145
Bulb, socket
000-AB9-013K
Full Door, s/s, hinged left, edge mount hinges
000-AB9-013J
Full Door, s/s, hinged right, edge mount hinges
000-AB9-013P
Half Door, s/s, bottom left, edge mount hinges
000-AB9-013R
Half Door, s/s, bottom right, edge mount hinges
000-AB9-013M
Half Door, s/s, top left, edge mount hinges
000-AB9-013N
Half Door, s/s, top right, edge mount hinges
3234617KT
Hinge, 1-5/16" offset with adjustable housing
1702796
Gasket, full door. s/s
1702797
Gasket, half door, s/s
Glass Door Replacement Parts
Part Number
Description
2198540
Ballast
2194290
Bulb, fluorescent, 18” coated, F15T8
000-AB9-013U
Full door, glass, hinged left, edge mount hinges
000-AB9-013T
Full door, glass, hinged right, edge mount hinges
000-AB9-013Y
Half door, glass, bottom left, edge mount hinges
000-AB9-013Z
Half door, glass, bottom right, edge mount hinges
000-AB9-013W
Half door, glass, top left, edge mount hinges
000-AB9-013X
Half door, glass, top right, edge mount hinges
3234617KT
Hinge, 1-5/16" Offset with adjustable housing
1701901
Gasket, full door, glass
1701902
Gasket, half door, glass
2194289
Lampholder
Delfield
™
18
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
®
6000XL Series Service and Installation Manual
Standard Labor Guidelines To Repair Or Replace Parts On Delfield Equipment
Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage.
•A maximum of 1-hour is allowed to diagnose a defective component.
•A maximum of 1-hour is allowed for retrieval of parts not in stock.
•A maximum travel distance of 100 miles round trip and 2-hours will be reimbursed.
•Overtime, installation/start-up, normal control adjustments, general maintenance, glass breakage, freight damage, and/or
correcting and end-user installation error will not be reimbursed under warranty unless pre-approved with a Service Work
Authorization from Delfield. You must submit the number with the service claim.
LABOR OF 1-HOUR IS ALLOWED TO REPLACE:
•Thermostat
•Evaporator/Condenser Fan Motor and Blade
•Hi-limit/Thermal Protector Switch
•Compressor Start Components and Overload Protector
•Condensate Element
•
•
•
•
•
Door Jamb Switch
Solenoid Coil
Fan Delay/Defrost Termination Switch
Door Hinges, Locks, and Gaskets
Thermometer
LABOR OF 2 HOURS TO REPLACE:
•Defrost Element
• Solenoid Valve
•Locate/Repair Leak
LABOR OF 3 HOURS TO REPLACE:
•Condenser or Evaporator Coil
•Expansion Valve
LABOR OF 4 HOURS TO REPLACE
•Compressor
This includes recovery of refrigerant and leak check.
$55.00 maximum reimbursement for refrigerant recovery (includes recovery machine, pump, torch, oil, flux, minor fittings,
solder, brazing rod, nitrogen, or similar fees.)
REFRIGERANTS
•R404A A maximum of $15.00/lb. or $1.00/oz. will be reimbursed.
Delfield
™
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
19
6000XL Series Service and Installation Manual
Manufacturers Limited Lifetime Warranty-ABS Liner
Delfield warrants to the original purchaser-user, subject to the
limitations and exclusions set forth below, that the ABS interior of the
Delfield models identified above will be free of manufactured defects
for as long as the equipment is owned by the original purchaser-user
and is in operation.
What is covered.
The interior liner of the 6000XL Series refrigerators are covered
against manufactured defects under normal use. For purposes of
this Warranty, interior liner is defined as the portion of the interior
liner which is made of ABS material. This warranty applies only to
products sold and installed after March 1, 2000 in the United States,
Canada, Puerto Rico, and Mexico. For purposes of this warranty,
lifetime is defined as the expected usable life for the equipment of 12
years.
Delfield’s Obligation
Limited strictly to shipping OEM replacement parts or repair kits
for any covered ABS interior. A Delfield authorized service dealer
and Delfield’s Service Department must confirm the liner defect
has occurred under normal conditions and is not due to misuse
as defined below. All decisions regarding the ABS interior shall be
made by Delfield’s Service Department and shall be binding upon
the parties. No labor or service charges or allowances are covered
by this warranty. Warranty service must be performed by a Delfield
approved authorized service agent.
User Responsibility
The product must be installed, cleaned and maintained as described
in the Service and Installation manual which is furnished with the
product. Only approved replacement parts may be used. Failure
to adhere to the requirements of this paragraph may void warranty
coverage.
Exclusions
This warranty does not cover labor, service, charges for travel time,
mileage, or premium charges. This warranty also does not include
defects resulting from:
•
Operation of the product beyond the specification set forth in the
Service and Installation Manual.
• Failure to clean and maintain the product as described in the
Service and Installation Manual.
• Installation of the product in a manner other than as set forth in
the Service and Installation.
• Use of installation of replacement parts not approved by
Delfield; or
• The introduction hot items directly onto the ABS liner.
This warranty is in lieu of all other warranties or guarantees of
any kind, express or implied, except Delfield’s One Year Parts
and One year Labor Warranty. ANY IMPLIED WARRANTIES OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
ARE HEREBY DISCLAIMED AND EXCLUDED. IN NO EVENT SHALL
DELFIELD BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES OF ANY KIND OR NATURE, OR FOR ANY DEFECT
RESULTING IN WHOLE OR IN PART FROM MISUSE, ALTERATION,
IMPROPER INSTALLATION OR INADEQUATE MAINTENANCE OF THE
PRODUCT OR ANY PART THEREOF.
No part or assembly which has been subject to accident, alteration
or misuse, or which has not been installed or serviced in accordance
with the Operation Manual furnished with the product, or which is
from equipment on which the serial number has been altered or
removed, shall be covered by this warranty.
Procedures
All claims for replacement parts or repair kits must be made through
a Delfield Parts Depot or an authorized Delfield dealer. The defective
part invoice must be returned to Delfield within 15 days after the
date of service to be eligible for warranty coverage. All claims
must include the model number, serial number, an original date of
installation and customer identification. Use of parts other than
original Delfield replacement parts will not be covered.
Delfield
™
20
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
®
6000XL Series Service and Installation Manual
Standard One Year Limited Warranty — Parts And Labor
The Delfield Company (“Delfield”) warrants to the Original Purchaser
of the Delfield product (herein called the “Unit”) that such Unit, and all
parts thereof, will be free from defects in material and workmanship
under normal use and service for a period of one (1) year from the date
of shipment of the Unit to the Original Purchaser or one (1) year from
the date of installation if registration is completed one (1) year from
installation. During this one year warranty period, Delfield will repair
or replace any defective part or portion there of returned to Delfield by
the Original Purchaser which Delfield determines was defective due to
faulty material or workmanship. During this one year warranty period,
Delfield will, subject to the limits set forth below, pay labor, crating,
and freight incurred in the removal of the Unit of defective component
and shipment to Delfield. A maximum of 1-hour is allowed to diagnose
a defective component. A maximum of 1-hour is allowed for retrieval
of parts not in stock. A maximum travel distance of 100 miles round
trip and 2-hours will be reimbursed. Overtime, installation/start-up,
normal control adjustments, general maintenance, glass breakage,
freight damage, delayed site entry because of security or hours of
operation and/or correcting an end-user installation error will not be
reimbursed under warranty unless pre-approved with a Service Work
Authorization from Delfield. Delfield will pay the return costs if the Unit
or part thereof was defective.
The term “Original Purchaser” as used herein means that person, firm,
association, or corporation for whom the Unit was originally installed.
This warranty does not apply to any Unit or part thereof that has
been subjected to misuse, neglect, alteration, or accident, such
as accidental damage to the exterior finish, operated contrary to
the recommendations specified by Delfield; or repaired or altered
by anyone other than Delfield in any way so as to, in Delfield’s sole
judgment, affect its quality or efficiency. This warranty does not
apply to any Unit that has been moved from the location where it was
originally installed. This warranty also does not cover the refrigerator
drier, door gaskets or the light bulbs used in the Unit. The warranty
is subject to the user’s normal maintenance and care responsibility
as set forth in the Service and Installation Manual, such as cleaning
the condenser coil, and is in lieu of all other obligations of Delfield.
Delfield neither assumes, nor authorizes any other person to assume
for Delfield, any other liability in connection with Delfield’s products.
Removal or defacement of the original Serial Number or Model
Number from any Unit shall be deemed to release Delfield from all
obligations hereunder or any other obligations, express or implied.
Parts furnished by suppliers to Delfield are guaranteed by Delfield
only to the extent of the original manufacturer’s express warranty to
Delfield. Failure of the Original Purchaser to receive such manufacturers
warranty shall in no way create any warranty, expressed or implied, or
any other obligation or liability on Delfield’s part in respect thereof.
Under no condition does this warranty give the Original Purchaser the
right to replace the defective Unit with a complete Unit of the same
manufacturer or of another make. Unless authorized by Delfield in
writing, this warranty does not permit the replacement of any part,
including the motor-compressor, to be made with the part of another
make or manufacturer.
No claims can be made under this warranty for spoilage of any
products for any reason, including system failure.
Delfield
™
The installation contractor shall be responsible for building access,
entrance and field conditions to insure sufficient clearance to allow
any hood(s), vent(s), or Unit(s) if necessary, to be brought into
the building. Delfield will not be responsible for structural changes
or damages incurred during installation of the Unit or any exhaust
system.
Delfield shall not be liable in any manner for any default or delay in
performance hereunder caused by or resulting from any contingency
beyond Delfield’s control, including, but not limited to, war,
governmental restrictions or restraints, strike, lockouts, injunctions,
fire, food, acts of nature, short or reduced supply of raw materials, or
discontinuance of the parts by the original part manufacturer.
Except as provided in any Additional Four Year Protection Plan, if
applicable, and the Service Labor Contract, if applicable, the preceding
paragraphs set forth the exclusive remedy for all claims based on
failure of, or defect for Delfield products sold hereunder, whether
the failure or defect arises before or during the warranty period, and
whether a claim, however instituted, is based on contract, indemnity,
warranty, tort (including negligence), strict liability, implied by statute,
common-law or otherwise , and Delfield and its agents shall not be
liable for any claims for personal injuries or consequential damages or
loss, howsoever caused. Upon the expiration of the warranty period,
all such liability shall terminate. THE FOREGOING WARRANTIES ARE
EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER
WRITTEN, ORAL, IMPLIED OR STATUTORY. NO IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE
SHALL APPLY, DELFIELD DOES NOT WARRANT ANY PRODUCTS OR
SERVICES OF OTHERS
This warranty supersedes and excludes any prior oral or written
representations or warranties. The sole and exclusive remedies of
any person relating to the Unit, and the full liability of Delfield for any
breach of this warranty, will be as provided in this warranty.
Other than this Delfield Standard One Year Limited Warranty, any
applicable Delfield Additional Four Year Protection Plan or applicable
Delfield Service Labor Contract, the Original Purchaser agrees and
acknowledges that no other warranties are offered or provided in
connection with or for the Unit or any other part thereof. The liability
of Delfield for breach of any warranty obligation hereunder is limited
to: (i) the repair or replacement of the Delfield Product on which the
liability is based, or with respect to services, re-performance of the
services; or (ii) at Delfield’s option, the refund of the amount paid for
said equipment or services. Any breach by Delfield with respect to any
item or unit of equipment or services shall be deemed a breach with
respect to that item or unit or service only
IN NO EVENT WILL DELFIELD BE LIABLE FOR SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES, OR FOR DAMAGES IN THE NATURE
OF PENALTIES.
If shipment of a replacement part is requested prior to the arrival in
the Delfield factory of the part claimed to be defective, the Original
Purchaser must accept delivery of the replacement part on a C.O.D.
basis, with credit being issued after the part has been received and
inspected at Delfield’s plant and determined by Delfield to be within
this warranty.
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
21
6000XL Series Service and Installation Manual
Additional Four Year Protection Plan — For Motor-Compressor Only
Delfield Model# Serial# Installation Date
In addition to the Standard One Year Warranty on the MotorCompressor contained in the above listed Delfield product (the
“Unit”), The Delfield Company (“Delfield”) also agrees to repair, or
exchange with similar or interchangeable parts in design and capacity
at Delfield’s option, the defective Motor-Compressor contained in the
Unit (the “Motor-Compressor”), or any part thereof, for the Original
Purchaser only, at any time during the four (4) years following the
initial one (1) year period commencing on the date of installation for
the Original Purchaser. This additional Warranty is only available if the
Motor-Compressor is inoperative due to defects in material or factory
workmanship, as determined by Delfield in its sole judgment and
discretion. The Original Purchaser shall be responsible for returning
the defective Motor-Compressor to Delfield prepaid, F.O.B. at the
address shown on the back cover of this manual.
The term “Original Purchaser” as used herein shall be deemed to mean
that person, firm, association, or corporation for whom the equipment
was originally installed.
The term “Motor-Compressor” as used herein does not include unit
base, air or water-cooled condenser, receiver, electrical accessories
such as relay, capacitors, refrigerant controls, or condenser fan/motor
assembly. This warranty does not cover labor charges incidental
to the replacement of parts. This warranty further does not include
any equipment to which said condensing unit is connected, such as
cooling coils, temperature controls or refrigerant metering devices.
This warranty shall be void if the Motor-Compressor, in Delfield’s
sole judgment, has been subjected to misuse, neglect, alteration or
accident, operated contrary to the recommendations specified by the
Unit manufacturer, repaired or altered by anyone other than Delfield
in any way so as, in Delfield’s sole judgment, to affect its quality or
efficiency or if the serial number has been altered, defaced or removed.
This Warranty does not apply to a Motor-Compressor in any Unit that
has been moved from the location where it was originally installed.
The addition of methyl chloride to the condensing unit or refrigeration
system shall void this warranty.
General Conditions
Delfield shall not be liable in any manner for any default or delay in
performance thereunder caused by or resulting from any contingency
beyond Delfield’s control including, but not limited to, war,
governmental restrictions or restraints, strikes, lockouts, injunctions,
fire, floods, acts of nature, short or reduced supply of raw material
or discontinuance of any part or the Motor-Compressor by the unit
manufacturer.
Replacement of a defective Motor-Compressor is limited to one (1)
Motor-Compressor by us during the four (4) year period. Delfield shall
replace the Motor-Compressor part only at no charge.
This Warranty does not give the Original Purchaser of the MotorCompressor the right to purchase a complete re placement MotorCompressor of the same make or of another make. It further does
not permit the replacement to be made with a Motor-Compressor
of another kind unless authorized by Delfield. In the event Delfield
authorizes the Original Purchaser to purchase a replacement MotorCompressor locally, only the wholesale cost of the Motor-Compressor
is refundable.
Expressly excluded from this warranty are damages resulting from
spoilage of goods.
Except as provided in any applicable Standard One Year Limited
Warranty or applicable Service Labor Contract, the foregoing is exclusive
and in lieu of all other war ran ties, whether written or oral, express
or implied. This Warranty supersedes and excludes any prior oral or
written representations or warranties. Delfield expressly disclaims any
implied warranties of merchantability, fitness for a particular purpose
or compliance with any law, treaty, rule or regulation relating to the
discharge of substances into the environment. The sole and exclusive
remedies of any person relating to the Motor-Compressor, and the full
liability of Delfield for any breach of this Warranty, will be as provided
in this Warranty.
Other than any applicable Delfield Standard One Year Limited Warranty,
this Delfield Additional Four Year Protection Plan and any applicable
Delfield Service Labor Contract, the Original Purchaser agrees and
acknowledges that no other warranties are offered or provided in
connection with or for the Motor-Compressor or any part thereof. In
no event will Delfield be liable for special, incidental or consequential
damages, or for damages in the nature of penalties.
Delfield
™
22
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
®
6000XL Series Service and Installation Manual
Notes
Delfield
™
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (888) 779-2040, www.delfield.com
23
Delfield
™
Mt. Pleasant, MI
®
Covington, TN
Thank you for choosing Delfield!
Help is a phone call away. Help our team of professional, courteous
customer service reps by having your model number and serial number
available at the time of your call (800) 733-8829.
Model:_______________________ S/N: _______________________
Installation Date:_______________
For a list of Delfield’s authorized parts depots,
visit our website at www.delfield.com.
Delfield
™
®
980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (989) 773-7981 or (800) 733-8829 • Fax (989) 773-3210 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2012 The Delfield Company. All rights reserved. Printed in the U.S.A.
DM6000XL 10/12
9294254
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement