ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator

ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
The Installation Space
Door Swing Clearances
The finished cutout width must be 35-1/2".
The installation must allow for clearances to adjacent walls or cabinets.
These refrigerators are equipped with a 2-position door stop. The
factory-set 130° door swing can be adjusted to 90° if clearance to
adjacent cabinets or walls is restricted.
35-1/2"
Finished Width
Wall View
2-5/16"
6"
10"
84-1/2" max
83-1/2" min
Finished
Opening
25"
Min. to
Wall
130° Door Swing
Electrical
Area
75" From
Floor to Bottom
of Electrical
Area
24" Cutout Depth
5" Water Supply
90° Door Swing
36-3/4"
5"
90°
130°
3 1/2"
3 1/2"
The cutout depth must be 24"
The refrigerator will project forward, slightly beyond adjacent cabinetry,
depending on your installation.
The cutout depth beneath a soffit
When installed beneath a soffit, the soffit cannot exceed the 24"
installation depth shown. The top case trim overlaps the bottom
of the soffit.
Electrical
A 115V, 60Hz., 15 or 20 amp power supply is required. An individual
properly grounded branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical receptacle recessed
into the back wall. Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
All models are equipped with an automatic icemaker. The water line can
enter the opening through the floor or back wall. Route GE SmartConnect™
Kit or 1/4" O.D. copper tubing between the cold water line and the water
connection location at the front of the refrigerator. The installation of an
easily accessible shut-off valve in the water line is required.
696Dia7
Product Dimensions
35"
Case Width
36"
Frame to Frame Width
Depth Including Handles:
26-7/8" Framed Models
27-3/4" Stainless Steel Models
Specification Created 5/04
110100
429Dia9
4" Min.
to Wall
605Dia20
Allow 25" minimum clearances for a full 130° door swing. Allow 15"
for pan removal.
*Shipping Height. The
refrigerator can be
adjusted to fit into a
cutout that is 83-1/2" min.
to 84-1/2" max. height.
The top case trim at the
front is 1/2" higher and
will overlap upper
cabinetry or soffit.
Use leveling legs and
wheels for a maximum
1" height adjustment.
605Dia21
• 4" minimum clearance is required when the door swing is adjusted to
90°. If the 90° door stop position is used, pan access is maintained,
but pan removal is restricted.
• See door swing illustrations to determine interaction with adjacent
cabinets or countertops.
ZUG2, ZUGSS2 Unified Grille Panel Kit
• If you are installing two refrigerators side by side, the installation space
must be 71-1/2" wide.
Note: Additional cutout width may be required when side panels are
used. Add side panel thickness to the finished cutout to calculate
rough-in width.
• The water and electrical locations for each product must be located
as shown.
• A separate 115V, 60Hz., 15 or 20 amp power supply is recommended for
each product.
71-1/2" Finished Width
Case Depth:
25-3/8" Framed Models
25-3/4" Stainless Steel Models
*84" From
Floor to
Top Frame
*83-1/2"
at
Rear
23-7/8"
Behind
Frame
2-5/16"
10"
10"
84-1/2" max
83-1/2" min
Finished
Opening
24" Cutout
Depth
5" Water Supply
3-1/2"
R
Wall View
24-3/16"
6"
Electrical
26"
Listed by
Underwriters
Laboratories
Water Supply 5"
26"
75" From
Floor to Bottom
of Electrical
Area
3-1/2"
For answers to your Monogram,® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
696Dia8
ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
Customization Basics: Framed or Overlay Panels,
Custom Handles and Accessory Kits
These bottom-freezer refrigerators are factory set for a left or right
door swing. The door swing is NOT reversible. Choose an RH model
with hinge on the right side; the door swings left to right. Choose an
LH model with hinge on the left side; the door will swing right to left.
Right-Hand
Door Swing
Left-Hand
Door Swing
Trimmed Refrigerators
ZIC360NRLH, ZIC360NRRH
Trimmed refrigerators are designed to be customized with decorative
panels. Field-installed custom door and grille panels are required.
Framed Panels
You may install 1/4"-thick custom panels from your cabinet
manufacturer. The decorative panel or accessory panel slides
into the factory-installed trim.
Door Handles
The supplied handles can be adjusted to accommodate both framed
or overlay panels. Custom handles of your choice, supplied by your
cabinetmaker, can also be installed. If desired, you may order ZKHCSS2
Monogram® Stainless Steel Tubular Handle Kit for overlay panels.
605Dia26
Side Panels
Side panels must be used whenever the sides of the refrigerator will
be exposed.
Optional Accessory Kits
ZKHCSS2: Monogram Stainless Steel Tubular Handle Kit and Handle
Side Trim for custom handles. For use on 3/4" custom panels.
ZUG2: For side-by-side installation of two trimmed bottom-freezer
refrigerators. This kit provides for the installation of a unified custom
grille panel to span the width of two units using a framed or overlay panel.
Standard Door Handle
Framed Panel
Standard supplied handles shown in 1/4" panel position.
Overlay Panels
You may also choose to install custom overlay panels from your cabinet
manufacturer. This design provides a seamless appearance which
integrates smoothly with surrounding cabinetry.
729Dia65
Standard
Door Handle
ZUGSS2: For side-by-side installation of two stainless steel-wrapped
bottom-freezer refrigerators. This kit provides a unified stainless steel
grille panel to span the width of two units.
Accessory Panels
White or black acrylic and stainless steel accessory panels are available
from your Monogram supplier. Panels are cut to size and ready to install.
These panel kits must be ordered separately.
Black
ZPBC360
3/4" Overlay Panel
.10" Thick Spacer Panel
1/4" Thick Backer Panel
Standard supplied handles shown in 3/4" overlay panel position.
Specification Created 5/04
110100
696Dia9
White
ZPWC360
R
Listed by
Underwriters
Laboratories
Stainless Steel
ZPSC360
For answers to your Monogram,® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
1/4" Framed Panel Dimensions
3/4" Overlay Panel Dimensions
If you choose to install framed panels,
they must be cut to the dimensions
shown. The panels will slide into the
frame on the door, drawer and grille.
For a more custom appearance, overlay
panels may be installed on trimmed
models. The overlay panel must be
secured to a 1/4"-thick backer panel
which slides into the trim. A spacer
panel 0.10" thick must be placed
between the overlay and backer panel.
Door/Drawer
If the custom panel is less than 1/4"
thick, and it fits loosely in the door
frame, it can be backed up with a
piece of filler material or foam tape
to improve the fit.
5/16"
Trim
Reveal
1/4"
Panel
Important Note: Maximum weight for
fresh food panel is 50 pounds,
30 pounds for freezer drawer panel
and 11 pounds for the grille panel.
A
Grille Panel
Fresh Food
Panel
B
Door/Drawer
1/4"
Backer
Panel
.250" + .10" + .750" =
1.100" Total Panel Thickness
729Dia84
Center each panel over
the other. Assemble the
panels with glue and
screws. Screws must
be countersunk into the
backer panel.
Overlay
Panel
.10"
Spacer
Overlay Panel
729Dia42
Spacer Panel
Backer Panel
C
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
Freezer Drawer
Panel
ZUG2 Grille Panel Dimensions
The ZUG2 Unified Grille Panel Kit will accept a framed or overlay
grille panel.
D
Framed Panel Dimensions (in inches)
A (Width) B (Grille Ht.) C (FF Ht.) D (FZ Ht.)
1/4" Framed Panel 33-7/8
8-7/8
46-1/16
21-7/8
729Dia89
3/4" Overlay Panel Dimensions (in inches)
A (Width) B (Grille Ht.)
1/4" Backer Panel 33-7/8
8-7/8
.10" Spacer Panel 32-1/2
7-5/8
3/4" Overlay Panel 34-1/8
9
C (FF Ht.)
46-1/16
44-11/16
46-5/16
D (FZ Ht.)
21-7/8
20-1/2
22
• Assemble the overlay panel in the same manner as the door and
drawer panels.
A
605Dia15
B
Grille Panel
Framed Panel Dimensions
A (Width)
1/4" Framed Panel
69-7/8"
B (Height)
8-7/8"
Overlay Panel Dimensions
A (Width)
1/4" Backer Panel
69-7/8"
.10" Spacer Panel
68-1/2"
3/4" Overlay Panel
70-1/8"
B (Height)
8-7/8"
7-5/8"
9"
729Dia85
Specification Created 5/04
110100
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
ZIC360NM – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
Advance Planning for Built-In Custom Bottom-Freezer Refrigerators
Frameless Cabinets: The case trim overlaps cabinets at the top and sides.
Therefore, frameless cabinets may require filler strips to prevent interference
with cabinet door swing. The opening must allow for filler strips.
Use this page to determine door
swing interaction with adjacent
cabinets or countertops.
Refrigerator
23-7/8" From
Rear of
Refrigerator
Case
Trim
3/4"
1/2"
1/4"
1"
1-3/4"
2"
1-1/2"
2-3/4"
3"
2-1/2"
1-1/4"
2-1/4"
1/4"
1/2"
3/4"
1"
l
ain
St
3/4" Overlay
Panel
(Nominal Size)
s
es
l
ee
St
Top View
130° Door Swing
(Optional setting)
Scale 1:1
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Specification Created 5/04
110100
Door
1/4"
1/2"
3/4"
1"
1-1/4"
ZIC360NM – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
Advance Planning for Built-In Custom Bottom-Freezer Refrigerators
Use this page to determine door
swing interaction with adjacent
cabinets or countertops.
Refrigerator
Case Trim
23-7/8"
From Rear of
Refrigerator
Frameless Cabinets: The case trim
overlaps cabinets at the top and sides.
Therefore, frameless cabinets may require
filler strips to prevent interference with
cabinet door swing. The opening must
allow for filler strips.
1/4"
1/2"
3/4"
1"
1-1/4"
1-1/2"
R
Door
1/2"
For answers to your Monogram, GE Profile or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
®
110100
3/4" Overlay
Panel
(Nominal Size)
1/4"
Listed by
Underwriters
Laboratories
Specification Created 5/04
Stainless Steel
Top View
90° Door Swing
(Optional setting)
Scale 1:1
™
3/4"
1"
1-1/4"
ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
Features and Benefits
• 20.6 Cu. Ft. Capacity
• Upfront electronic controls with digital readout
• Multi-shelf air management tower
• 2 Sealed, adjustable humidity vegetable/fruit pans with
easy access lids and full extension slides
• 2 Sealed deli pans with full extension slides
• Adjustable spillproof glass cabinet shelves
• Slide-out freezer compartment with full
extension slides
• Model ZIC360NRRH – Right-handed door swing
(Door panels required)
• Model ZIC360NRLH – Left-handed door swing
(Door panels required)
ZIC360NRLH.EPS
Specification Created 5/04
110100

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project