Clarion | FB278RBT | Owner`s manual | Clarion FB278RBT Owner`s manual

Clarion FB278RBT Owner`s manual
Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC
Déclaration de Conformité relative à la Directive 1999/5/CE
Konformitätserklärung nach der R&TTE Directive 1999/5/EC
Dichiarazione di conformità con la Direttiva R&TTE 1999/5/CE
Conformiteitsverklaring betreffende de R&TTE directief 1999/5/EC
Declaración de Conformidad en referencia a la Directiva R&TTE 1999/5/EC
Deklaration om Överensstämmelse med hänseende till R&TTE-direktivet 1999/5/EC
Declaração de Conformidade no que diz respeito à Directiva R&TTE 1999/5/EC
Manufacturer:
Clarion (Malaysia) Sdn. Bhd.
Phase 3, Free Industrial Zone, 11900 Bayan
Lepas, Penang, Malaysia.
EU Representativeʼs:
Clarion Europa GmbH
Hessering 19-21 64546 Mörfelden Walldorf Germany.
English:
Nederlands:
Français:
Español:
Deutsch:
Svenska:
Italiano:
Português:
Hereby, Clarion declares that this unit
FB278RBT is in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC.
Clarion déclare par la présente que cet appareil,
FB278RBT, est en conformité avec les exigences
essentielles et autres dispositions pertinentes de
la Directive 1999/5/CE.
Hiermit erklärt Clarion, dass dieses Gerät
FB278RBT die wesentlichen Anforderungen und
sonstigen Vorschriften der Directive 1999/5/EC
erfüllt.
Con la presente, Clarion dichiara che questa
unità FB278RBT è conforme con i requisiti
essenziali ed altre norme rilevanti della Direttiva
1999/5/CE.
Ownerʼs manual
Mode dʼemploi
Bedienungsanleitung
Istruzioni per lʼuso
Gebruiksaanwijzing
Manual de instrucciones
Bruksanvisning
Manual de instruções
Hierbij verklaart Clarion dat deze unit FB278RBT
overeenkomstig is met de essentiele vereisten
en andere relevante bepalingen van directief
1999/5/EC.
Por la presente, Clarion declara que esta unidad
FB278RBT cumple los requisitos esenciales y
otras condiciones importantes de la Directiva
1999/5/EC.
Härmed förkunnar Clarion, att denna enhet
FB278RBT uppfyller de nödvändiga kraven
samt andra relevanta bestämmelser i Direktiv
1999/5/EC.
A Clarion declara por este meio que a unidade
FB278RBT cumpre com os requisitos essenciais
e outras provisões relevantes da Directiva
1999/5/EC.
Clarion Co., Ltd.
All Rights Reserved. Copyright © 2007: Clarion Co., Ltd.
Printed in Malaysia / Imprimé en Malaisie / Gedruckt in Malaysia / Stampato in Malaysia
Gedrukt in Maleisi / Impreso en Malasia / Tryckt i Malaysia / Impresso na Malásia
Bluetooth® SD/MP3 RECEIVER
ÉMETTEUR SD/MP3 Bluetooth®
Bluetooth® SD/MP3 RECEIVER
RICEVITORE Bluetooth® SD/MP3
Bluetooth® SD/MP3 RECEIVER
RECEPTOR Bluetooth® SD/MP3
Bluetooth® SD-/MP3-RECEIVER
RECEPTOR Bluetooth® SD/MP3
PE-8500E
280-8579-00
280-8346-00
The control panel can be detached to prevent
theft. When detaching the control panel, store it
in the DCP (Detachable Control Panel) case to
prevent scratches.
We recommend taking the DCP with you when
leaving the car.
Attaching the DCP
1. Insert the right side of the DCP into the main
unit.
2. Insert the left side of the DCP to attach into the
main unit.
Removing the DCP
1. Press the [SRC] button for 1.5 seconds or
longer to switch off the power.
Storing the DCP in the DCP case
Hold the DCP, in the orientation as shown in the
figure below, and put it into the supplied DCP case.
(Ensure the DCP is in the correct orientation.)
2. Press in the [RELEASE] button.
∗ The flip down panel can only be opened up
to 65˚, please do not forcibly push to open
further.
Contents
English
English
5. DCP (Detachable Control Panel)
1. PRECAUTIONS .............................................................................................................................. 3
2. HANDLING MEMORY CARD ......................................................................................................... 4
3. CONTROLS .................................................................................................................................... 5
MAIN UNIT ...................................................................................................................................... 5
4. NOMENCLATURE .......................................................................................................................... 6
Names of the Buttons and Their Functions ..................................................................................... 6
Display Items ................................................................................................................................... 7
LCD Screen ..................................................................................................................................... 7
5. DCP (Detachable Control Panel) .................................................................................................. 8
6. OPERATIONS ................................................................................................................................. 9
Basic Operations ............................................................................................................................. 9
Radio Operations .......................................................................................................................... 10
RDS Operations ............................................................................................................................ 12
MP3 Operations ............................................................................................................................ 13
Introduction to Bluetooth® Wireless Technology ............................................................................. 20
Handsfree Operations ................................................................................................................... 22
Audio Streaming Operations ......................................................................................................... 24
Common Operations ..................................................................................................................... 25
Compatible Devices ...................................................................................................................... 30
7. ADDITIONAL INFORMATION ...................................................................................................... 31
8. TROUBLESHOOTING .................................................................................................................. 33
9. ERROR DISPLAYS ...................................................................................................................... 36
10. SPECIFICATIONS ........................................................................................................................ 37
2. HANDLING MEMORY CARD
SD/MMC Memory Card
Do not leave the card in vehicle where there
is high temperature or direct sunlight or
where electromagnetic waves or electrostatic
are easily generated.
Do not allow dirt, dust or water to enter it.
When the card is being read, do not remove
the card.
Do not bend or drop the card. The card or
the recorded content may be damaged.
After eject operation, always remove the
memory card from the slot; otherwise, the flip
down panel may not be closed properly.
After usage, store the supplied memory card
in the enclosed case.
1. PRECAUTIONS
! CAUTION
3. Pull the DCP toward you and remove it.
The DCP can easily be damaged by shock.
After removing it, be careful not to drop it
or subject it to strong shocks.
These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
The connector connecting the main unit and
the DCP is an extremely important part. Be
careful not to damage it by pressing on it
with fingernails, pens, screwdrivers, etc.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Note:
If the DCP is dirty, wipe off the dirt with a soft, dry
cloth only.
FB278RBT
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to consult the dealer or an
experienced radio/TV technician for help.
Do not touch the terminals on the back of the
card with your fingers.
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY.
4. Close the HOLD FLAP.
8
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
SD Logo is a trademark.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Clarion Co.,Ltd. is
under license. Other trademarks and trade names are those of their respective owners.
®
®
FB278RBT
3
4
Be sure to unfold and read the next page. / Veuillez déplier et vous référer à la page suivante.
Bitte ausbreiten und die nächste Seite lesen. / Assicurarsi di aprire e leggere la pagina successiva.
Volgende pagina uitvouwen en doorlezen a.u.b. / Cerciórese de desplegar y de leer la página siguiente.
Glöm inte att vika ut och läsa nästa sida. / Não deixe de abrir e ler a próxima página.
FB278RBT
Notes:
Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5.
SD is the abbreviation of Secure Digital Card while MMC is the abbreviation of Multimedia card.
Names of the Buttons and Their Functions
SD/MMC MEMORY CARD SLOT
SD/MMC memory card insertion slot.
Deutsch
[RELEASE] button
Deeply push in the button to unlock the flip down
panel.
[
Italiano
Nederlands
Español
With the FLIP DOWN PANEL opened / Ouvrez le PANNEAU RABATTABLE
ÖFFNUNG DER KLAPPSCHALTTAFEL / Apertura del PANNELLO APRIBILE
Met het NEERKLAPBARE PANEEL geopend / Apertura del PANEL ABATIBLE
DEN NEDFÄLLBARA PANELEN öppen / Abrindo o PAINEL RECLINÁVEL
Svenska
/ FENTE DE CARTE MÉMOIRE SD/MMC /
SD/MMC-SPEICHERKARTEN SCHLITZ / SLOT SCHEDA DI MEMORIA SD/MMC /
SLEUF VOOR SD/MMC-GEHEUGENKAART / RANURA PARA TARJETA DE MEMORIA SD/MMC /
SD-/MMC-MINNESKORTÖPPNING / SLOT DO CARTÃO DE MEMÓRIA SD/MMC
Português
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.
Hinweis: Bitte diese Seite ausfalten und beim Lesen der einzelnen Kapital die Frontdiagramme beachten.
Nota: Assicurarsi di aprire questa pagina e fare riferimento a questi diagrammi quando si legge ciascun capitolo.
Opmerking: Vouw deze pagina uit en zie tevens de afbeeldingen van het voorpaneel tijdens het doorlezen van de volgende hoofdstukken.
Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.
Observera: Vik ut denna sida för att kunna se figurerna över bilstereons framsida medan du läser de olika kapitlen.
Nota: Certifique-se de abrir esta página e consulte os diagramas frontais conforme realiza a leitura de cada capítulo.
5
FB278RBT
Display Items
4. NOMENCLATURE
English
Français
MAIN UNIT / APPAREIL PRINCIPAL / HAUPTGERÄT
/ APPARECCHIO PRINCIPALE / HOOFDTOESTEL
/ UNIDAD PRINCIPAL / HUVUDENHET / UNIDADE PRINCIPAL
English
English
3. CONTROLS / LES COMMANDES / REGLER
/ CONTROLLI / REGELAARS / CONTROLES
/ KONTROLLER / CONTROLOS
] knob
Adjust the volume by turning the knob clockwise
or counterclockwise.
Press and hold the knob for 1.5 seconds or
longer to perform auto store in the Radio
mode.
Play or pause a track while in the SD/BT Audio
mode.
Press and hold the knob for 1.5 seconds or
longer to perform manual navigation in the SD
mode.
Perform next level adjustment or selection in
the Adjustment mode.
Perform various settings.
INTERNAL MIC
Built-in internal microphone.
[SRC] button
Press the button to turn on the power.
Press and hold the button for 1.5 seconds or
longer to turn off the power.
Switch the Operation mode among the Radio
mode, SD mode, BT Audio mode and AUX
mode.
[
] button
Accept an incoming call or make outgoing call.
[
] button
Reject an incoming call or end a call.
Cancel current operation.
[BND] button
Switch the band while in the Radio mode.
Press and hold the button for 1.5 seconds or
longer to toggle seek/manual tuning.
Play the first track in current folder while in the
SD mode.
Press and hold the button for 1.5 seconds or
longer to play the first track in the memory
card.
6
FB278RBT
[DISP] button
During Radio mode, switch the display indication
in the following order:
Frequency Station ID
Radio Text
Frequency...
During SD mode, switch the display indication
in the following order:
Track Name Folder Name Title Tag
Album Tag
Artist Tag Track Name...
Press and hold the button for 1.5 seconds or
longer to enter the Adjustment mode.
[
,
] buttons
Seek a station while in the Radio mode or
select a track when listening to a SD/BT Audio
mode.
These buttons are also being used to make
various settings.
[1] button
Restart current track in the SD mode.
[RPT] button
Perform track repeat play while in the SD
mode.
Press and hold the button for 1.5 seconds or
longer to perform folder repeat play while in the
SD mode.
[RDM] button
Perform track random play while in the SD
mode.
Press the button to toggle track random/folder
random/card random/random off while in the SD
mode.
Press and hold the button for 1.5 seconds or
longer to perform quick random folder play.
[
], [
] buttons
Select the folder in the SD mode.
[DIRECT] buttons
Store a station into memory or recall it directly
while in the Radio mode.
Store a telephone number into memory or recall
it directly while in the Telephone mode.
[TA] button
Use the button to set the TA ( Traffic
Announcement) standby mode.
∗ Some of the modes will change the whole display such as volume, Adjustment mode and file navigation.
LCD Screen
In extreme cold, the screen movement may slow down and the screen may darken, but this is normal.
The screen will recover when it returns to normal temperature.
Please take note that reflection of the screen cover may increase due to direct sunlight exposure, thus
this might decrease the visibility of the LCD screen.
FB278RBT
7
Basic Operations
Note: Be sure to read this chapter referring to the front diagrams of
chapter “3. CONTROLS” on page 5.
English
6. OPERATIONS
! CAUTION
Be sure to lower the volume before switching off the unit power or the ignition key. The
unit remembers its last volume setting. If
you switch the power off with the volume up,
when you switch the power back on, the sudden loud volume may hurt your hearing and
damage the unit.
Turning on/off the power
1. Press the [SRC] button.
2. The illumination and display on the unit light
up. The unit automatically remembers its last
Operation mode and will automatically switch
to display that mode.
3. Press and hold the [SRC] button for 1.5 seconds or longer to turn off the power for the
unit.
∗ A welcome animation will be displayed at the
first time. This animation can be turned on or
off in the Adjustment mode.
Notes:
Be careful about using this unit for a long time
without running the engine. If you drain the carʼs
battery too much, you may not be able to start the
engine and this can reduce the service life of the
battery.
The unit will automatically prevent from being
turned on the power for a few seconds after power
off for internal protection purposes.
Selecting a mode
1. Press the [SRC] button to change the Operation mode.
2. Each time you press the [SRC] button, the Operation mode changes in the following order:
Radio mode SD mode
(BT Audio mode) (AUX mode)
Radio mode...
∗ AUX mode is only available if AUX is enabled
in ADJ mode while BT Audio mode will only be
available if there is A2DP connection.
Notes:
There will be screen wipe transition in between if
animation is enabled in Adjustment mode.
If the SD mode is selected when no SD memory
card is inserted, the display shows “NO CARD”.
Switching the display
Press the [DISP] button to select the desired display.
When the [DISP] button is pressed at the first
time, the current display type will be displayed.
Further pressing the [DISP] button will switch the
display in the following order:
Radio mode
“FREQUENCY”
“RADIO TEXT”
“STATION ID”
“FREQUENCY”...
∗ Please refer chapter “RDS Operations” on page
12 for more details.
SD mode
“TRACK” “FOLDER” “TITLE”
“ARTIST” “TRACK” ...
“ALBUM”
∗ Once selected, the preferred display becomes the
display default. When a function adjustment such
as volume is made, the screen will momentarily
switch to that functionʼs display, then revert back
to the preferred display several seconds after the
adjustment.
And the following title will be displayed for a
moment each time the mode changes.
FB278RBT
9
English
Basic Operations
Radio Operations
Adjusting the volume
Listening to the radio
“VOLUME 0” to “VOLUME 33” will be displayed
depends on the volume level.
2. To select a preset band, press the [BND] button, then select one of the preset bands such
as FM1, FM2 or FM3. Every time the [BND]
button is pressed, the display will change as:
] knob clockwise inTurning the [
creases the volume; turning it counterclockwise
decreases the volume.
∗ Factory default setting for volume is “VOLUME
13”.
AUX function
This system has AUX RCA input in the rear panel
where you can listen to sounds and music from
external devices connected to this unit.
1. Connect the external music player to the AUX
RCA input.
2. Enable the AUX function in Adjustment mode.
Please refer “Setting AUX function” on page
26 for more details.
3. Press the [SRC] button to select the AUX mode
to activate the AUX function.
Note:
Volume can be adjusted through the unit.
Please refer chapter “Common Operations” on
page 25 for more operation controls.
1. Press the [SRC] button and select the Radio
mode, then the radio will be on.
FM1
FM2
FM3
,
3. Press the [
desired station.
FM1...
] button to tune in the
∗ Initial frequency display is “87.50MHz”.
Seek tuning
There are 2 types of seek tuning: DX SEEK and
LOCAL SEEK.
DX SEEK can automatically tune in to receivable
broadcast stations; LOCAL SEEK can tune in to
only broadcast stations with a good reception
sensitivity.
1. Press the [BND] button and select the desired
FM band.
∗ Press and hold the [BND] button for 1.5 seconds
or longer to switch to Auto Seek mode. Make
sure “SEEK TUNE” is displayed briefly.
2. Press the [
,
station tuning.
] button to start automatic
] button is pressed, search
When the [
will be performing in the direction of higher fre] button is pressed,
quencies. When the [
search will be performed in the direction of
lower frequencies.
DX SEEK
] button is pressed, search will be
When the [
performing in the direction of higher frequencies.
] button is pressed, search will be
When the [
performed in the direction of lower frequencies.
∗ When seek tuning starts, “DX” appears in the
display.
LOCAL SEEK
If the button is pressed and held in position for
1.5 seconds or longer, local seek tuning will be
enabled. Broadcast stations with good reception
sensitivity are selected.
∗ When local seeking starts, “LO” appears in the
display.
10
FB278RBT
Manual tuning
There are 2 ways available: Quick tuning and
step tuning.
When you are in the step Tuning mode, the frequency changes one step at a time. In the Quick
Tuning mode, you can quickly tune the desired
frequency.
1. Press the [BND] button and select the desired
FM band.
∗ Press and hold the [BND] button for 1.5 seconds
or longer to switch to Manual Seek mode. Make
sure “MANUAL TUNE” is displayed briefly.
2. Tune into a station.
] button for 1.5 secPress and hold the [
,
onds or longer to begin station tuning.
Press the [
tuning.
,
] button to perform manual
Preset memory function
Preset memory function can store up to 18 stations:
Six stations for each of FM1, FM2, and FM3.
∗ Factory default setting is empty for all channels.
Manual memory function
1. Press the [BND] button, to select a band you
want to store in the memory.
2. Press the [
,
desired station.
Auto store is a function for storing up to 6 strongest stations that are automatically tuned in
sequentially. If 6 receivable stations cannot be
received, a previously stored station remains unoverwritten at the memory position.
] knob for
1. Push and hold the [
1.5 seconds or longer. The stations with good
reception are stored automatically to the preset
channels.
Notes:
The stations are stored in FM3 even if FM1 or FM2
was chosen for storing stations.
The auto store procedure may take up to 40 seconds to complete.
Quick tuning
Step tuning
Auto store
English
Radio Operations
] button to tune into a
3. Press and hold one of the [DIRECT] buttons
for 1.5 seconds or longer to store the current
station into preset memory and “SAVED” will
be displayed briefly.
Note:
Each preset channel stores the PS (Programme
service) and AF (Alternate frequency) information.
Please refer chapter “RDS Operations” on page
12 for more details.
Recalling a preset station
A total of 18 preset positions (6-FM1, 6-FM2, 6FM3) exists to store individual radio stations in
memory. Pressing the corresponding [DIRECT]
button recalls the stored radio frequency automatically.
1. Press the [BND] button and select the desired
FM band.
2. Press the corresponding [DIRECT] button to
recall the stored station.
∗ Press and hold one of the [DIRECT] buttons for
1.5 seconds or longer to store that station into
preset memory.
Notes:
If there is no preset channel stored, “- -EMPTY- -” is
displayed briefly and reverts to previous frequency
display.
If a preset channel is selected, the previously stored
station will be displayed. If no station can be found
on the previous frequency, the unit will search the
previously stored AF list.
! CAUTION
When radio station is being received nearby
a radio transmission tower, radio quality may
be affected. As a result, you may encounter
other radio station interference and RDS data
may not be received correctly in this situation.
FB278RBT
11
English
RDS Operations
RDS (Radio Data System)
This unit has a built-in RDS decoder system that
supports broadcast stations transmitting RDS
data.
This system can display the name of the broadcast station being received (PS) and can automatically switch to the broadcast station with the
best reception as you move long distances (AF
switching).
Also, if a traffic announcement is broadcast from
an RDS station, no matter what mode you are in,
this broadcast is received.
Additionally, if EON information is received, this
information enables automatic switching of other
preset stations on the same network and interruption of the station being received with traffic
information from other stations (TP). This function is not available in some areas.
AF
: Alternative Frequency
PS : Programme Service Name
EON : Enhanced Other Network
TP
: Traffic Programme
FREQUENCY : Current frequency, such as
“87.50MHz”
STATION ID
: Programme service name of
current station
RADIO TEXT : Text Messages from current
station
If there is no STATION ID information available,
frequency will be displayed.
When RADIO TEXT is selected, the frequency
will still be displayed until a complete message
is received. The message will continue to be displayed until a new message is received. If there
is no Radio Text data available after 45 seconds,
frequency will be displayed again.
Note:
Factory default setting is FREQUENCY display
information type.
AF function
The AF function switches to a different frequency
on the same network in order to maintain optimum reception.
∗ When set receives RDS signal, and can read PS
data, PS appears in the display (if set to STATION
ID display mode).
∗ The factory default setting is “ON”.
Note:
This unit doesnʼt support Programme Type (PTY)
and Regional Programme Function (REG).
2. Press the [
RDS display information
There is several displays selection during listening to a station.
1. Press the [DISP] button to display current
display type.
2. To select the next type, press the [DISP] button again.
The arrangement is shown below.
1. Press and hold the [DISP] button for 1.5 seconds or longer to enter adjustment mode.
3. Turn the [
or “OFF”.
ON
,
] button to select “AF”.
] knob to select “ON”
: AF function turns on.
OFF : AF function turns off.
4. Press the [
ous mode.
] button to return to the previ-
∗ If the reception of the current broadcast station
deteriorates, “AF XXX.XXMHz” appears in the
display where XXX.XX is the frequency of the
AF that is being tested. The radio searches for
the same programme on another frequency.
TA (Traffic Announcement)
In the TA standby mode, when a traffic announcement broadcast starts, the traffic announcement
broadcast is received as top priority regardless of
the Function mode so you can listen to it. However, traffic announcement will not interrupt a call.
∗ This function can only be used when “TP” is lit in
the display. When “TP” is lit, this means that the
RDS broadcast station being received has traffic
announcement programmes.
12
FB278RBT
MP3 Operations
Setting the TA standby mode
What is SD/MMC card?
If you press the [TA] button when only “TP” is lit in
the display, “TP” and “TA” light in the display and
the unit is set into the TA standby mode until a
traffic announcement is broadcast. When a traffic
announcement broadcast starts, “TRAFFIC” appears briefly in the display. and then the relevant
display is shown depends on the current display
mode (Radio Text/ Frequency/Station ID). A car
indicator will light up in the display. If you press
the [TA] or [SRC] button while a traffic announcement broadcast is being received, the traffic announcement broadcast reception is cancelled
and the unit goes into the TA standby mode.
Notes:
Telephone interruption will not be affected by TA
interruption.
If the TA function is turned on in the middle of an
active Traffic Announcement, the current TA interruption will be ignored. It will only valid for the next
Traffic Announcement.
Cancelling the TA standby mode
As “TP” and “TA” indicators lights on, press the
[TA] button. The “TA” indicator goes off and the
TA standby mode is cancelled.
Volume setting of TA
The volume for TA interrupts can be set during
TA interrupt. It is independent from main volume.
During TA interrupts, the unit will select between
TA and main volume whichever is higher as the
new TA volume.
∗ The factory default setting for this volume is “15”.
]
During a TA interrupt, turn the [
knob to set the volume to the desired level (0 to
33).
The MultiMediaCard (MMC) and Secure Digital
(SD) are flash memory (non-volatile) card format
that are used to store large capacity of data in
a compact and slim size of media. SD memory
cards are based on the older MultiMediaCard
(MMC) format with additional features such as
write protection switch.
English
RDS Operations
Memory card that can be played are limited to
those recognized as SD or MMC; operation
is not guaranteed with all SD memory card
from all manufacturers. For SD/MMC memory
card compatibility, please consult your nearest
Clarion dealer for more information.
To prevent the accidental loss of data, always
back up important data to your computer.
Audio files playable on this unit are limited to
MP3 files. AAC, WMA or other audio formats
are not supported.
This unit doesnʼt support SDHC ( Secure
Digital High Capacity) and SDIO (input/output)
cards.
This unit supports SD memory card up to 2GB
based on SD Association standard.
What is MP3?
MP3 is an audio compression method and classified into audio layer 3 of MPEG standards. This
audio compression method has penetrated into
PC users and become a standard format. This
MP3 features the original audio data compression to about 12 percent of its initial size with a
high quality sound. This means that several music CDs can be recorded on a SD card to allow a
long listening time∗.
∗ Depends on the SD card storage capacity.
∗ When the TA interrupt ends, the volume returns to
the level it had before the interrupt.
FB278RBT
13
English
MP3 Operations
Precautions when creating MP3 in SD/
MMC card
Usable sampling rates and bit rates:
MP3
Decode Format
Sampling Rate
(kHz)
Bit-rate (kbps)
SD/MMC
Format
Folder structure
1. SD card with a folder having more than 8 hierarchical levels will be impossible. However,
the following hierarchical structure is recommended.
MPEG 1 and 2 - Layer 3
MPEG-1 : 32, 44.1, 48
MPEG-2 : 16, 22.05, 24
MPEG-1 : 32 - 320
MPEG-2 : 8 - 160
VBR
FAT12 or FAT16
Folder Level limit
: 8 Level
Max. Folder Support : 255
Max. Files Support
: 255
Folder Name
: Max. 30 Characters
File Name
: Max. 30 Characters
File extensions
Always add a file extension “.MP3” to MP3 file
by using single byte letters. If you add a file
extension other than specified or forget to add
the file extension, the file cannot be played.
Never simply change any file extension to
“.MP3” as this will cause unexpected result
and may damage the unit as well. Please use
appropriate audio converter to change to valid
mp3 files.
Logical format (File system)
1. When writing MP3 file on a SD/MMC card,
please select “FAT12” or “FAT16” as the
system file format. Please be aware that the
Windows XP will format any volume of 512MB
or larger with FAT32 by default. Thus, if the disk
is using “FAT32” system file format, please
format the disk with “FAT” system file format
which is “FAT16”. All the data will be erased
during formatting. Thus, please backup your
data accordingly.
2. The folder name and file name can be displayed as the title during MP3 play but the
title must be within 30 single byte alphabetical
letters and numerals (not including a file extension). Longer name will not be displayed.
14
FB278RBT
Notes:
“ ” is a number of folders that are limited to
“Number of files or folders” conditions.
Please use subdirectory/subfolder as recommended and avoid placing all the audio files in the
root directory.
Number of files or folders
1. Up to at least 255∗ files can be recognized
per folder.
Up to at least 255∗ files can be played.
∗ Entries includes sub-folders and MP3 files.
2. Tracks are always sorted alphabetically and
played in that order. (Tracks might not always
be played in the order displayed on the PC.)
3. Some noise may occur depending on the type
of encoder software used while recording.
! CAUTION
Never insert foreign objects into the SD/
MMC memory card slot as it may cause the
unit to break down.
English
MP3 Operations
Do not insert memory card other than
specify. It may be impossible to extract
these cards from the unit and such damage
will not be covered by the warranty on this
product. If the memory card is not inserted
easily, there may be another memory card
in the slot or the unit may require service.
This unit is designed for playing SD/MMC
card only.
Do not forcibly insert the memory card to
the slot with incorrect direction (label side
facing down or reverse direction) as this
will damage the memory card as well as
the SD/MMC MEMORY CARD SLOT.
Do not leave a memory card unattended in
an automobile. Exposure to direct sunlight
or high temperatures may cause deformation or other malfunction of the memory
card.
When the memory card is subjected to electrostatic or electric noise, this may result in
the loss of data.
Loading a memory card
1. Press the [RELEASE] button to flip down the
panel.
2. Insert a memory card into the SD/MMC MEMORY CARD SLOT with the label side facing
up.
3. Close the flip down panel. “Loading...” appears
in the display, the memory card plays automatically after loading.
Playback will begin from the first file recorded
on the memory card.
Notes:
Sound will be muted when panel is flipped.
“FLIPPED” will be displayed.
Always insert the memory card fully by pushing it
into the slot. Incomplete insertion may cause the
memory card not be recognized and flip down panel
will not be able to close.
Depending on the number of tracks and folder
structure recorded, some amount of time may be
required until all tracks are read into the unit. Thus,
please refer chapter “Folder structure” on page
14 for recommended folder hierarchy and optimal
performance. It is best to avoid folders without MP3
files in memory card as this will increase loading
time.
Eject function
1. Press the [RELEASE] button to flip down the
panel.
2. Push the memory card slowly to eject and
remove it when ejected.
3. Close the flip down panel after removing the
memory card.
Notes:
SD memory card may pop out during removal.
If you remove a memory card such as Micro/Mini SD
and leaving the SD memory card adaptor attached
to the unit, it may be hard to remove the adaptor
alone from the unit later. Thus, always remove both
the memory card and adaptor together if you are
using a memory card adaptor.
FB278RBT
15
English
MP3 Operations
Pausing play
] knob to pause play.
1. Push the [
“ ” appears in the display.
2. To resume track play, push the [
knob again. “ ” appears in the display.
]
Display titles
This unit can display title data for the memory
card.
1. Press the [DISP] button to display current title
type.
2. To select the next type, press the [DISP] button
again.
The arrangement is shown below.
! CAUTION
Do not remove the memory card when
the panel is not fully flipped as this may
damage the memory card as well as the
unit. Remove the card only when it is fully
flipped.
Do not drop the memory card into the space
of the flipped down panel.
Listening to a memory card already
loaded in the unit
Press the [SRC] button to select the SD mode.
“
” indicator will light on.
3. Relevant information will be displayed after
showing the title type.
Notes:
If no Artist information, “NO ARTIST” will be displayed.
When the unit enters the SD mode, play starts
automatically.
If a MP3 file encode with ID3 TAG header but not
consist of any TAG information, “unknown” will be
displayed and change according to the following
display:
∗ If there is no memory card loaded, the indication
“NO CARD” appears in the display.
- If no Album information, the folder name will be
displayed.
∗ If there is no MP3 file is detected, the indication
“NO MP3” appears in the display.
- If no Title information, the filename will be displayed.
∗ The mode changes each time the [SRC] button is
presssed.
16
FB278RBT
Supports ID3 Tags v2.3 and v2.4. Earlier ID3 tags
version is ignored but the track is playable.
Only ASCII characters can be displayed in Tags.
UNICODE ID3 (Chinese, Japanese and etc) is not
supported.
If ID3 TAG has Japanese, Chinese or other nonsupported characters, “∗” will be displayed as
substitution.
The folder name will be displayed as “(Root)” which
the file allocates in the root directory.
Folder select
This function allows you to select a folder containing MP3 files and start playing from the first
track in the folder.
1. Press the [
] or [
2. Press the [
Press the [
folder.
] button to move the next folder.
] button to move the previous
English
MP3 Operations
] button.
MP3 playing order
When selected for playing folder/track up down
functions, files and folders are always accessed
in alphabetical order. Due to this, the order in
which they are expected to be played may not
match the order in which they are actually played.
If you do not want the tracks to play in alphabetical order, then you can prefix them with 00, 01,
02 etc. to force them to play in a certain order.
Please refer chapter “Folder structure” on page
14 for recommended folder/file hierarchy.
Selecting a track
Track-up
] button to move ahead to the
1. Press the [
beginning of the next track.
] button is pressed, the
2. Each time the [
track advances ahead to the beginning of the
next track.
Track-down
] button to move to the begin1. Press the [
ning of the previous track.
] button is pressed, play2. Each time the [
back proceeds to previous track in the reverse
direction.
Notes:
Previous track across multiple sub-folders may not
be always return to the previous song you listen as
it will return to the last valid MP3 files of the parent
folder.
Fast forward/fast backward is not supported in this
unit.
3. Press the [
,
] button to select a track.
Notes:
] button while in the final folder will
Press the [
shift to the first folder.
] button while in the first folder will
Press the [
shift to the last folder.
Press the [ ] button will always play the last track
of previous folder.
Folder without a MP3 file is not selectable.
] button for 1.5
Press and hold the [
,
seconds or longer will also perform as folder down/
up.
Manual navigation
Alternatively, you can use the Manual Navigation mode to select folder and files. Track will
be played directly when the specific track is selected.
] knob for
1. Push and hold the [
1.5 seconds or longer in SD mode to enter
Manual Navigation mode.
,
2. Press the [
or track navigation.
] button to select folder
FB278RBT
17
English
MP3 Operations
Top function
Return to the first track of the memory card or
the folder currently being played back, and start
playing.
1. Press the [BND] button to play from the first
track of the current folder.
3. Turn the [
or track.
] knob to select folder
∗ The track play will take effect immediately.
] knob again or press
4. Push the [
] button to exit the mode.
the [
Folder Navigation : Search the folders that
contains tracks.
Track Navigation : Search tracks within the
selected folder.
Notes:
During searching next/previous folder in folder
navigation, amount of time will be required depends
on the complexity of folder structure. Animated dots
“.....” may be appeared in folder navigation during
complex folder searching. “Loading...” will be
displayed if Manual Navigation mode is exit during
this searching.
If no operation is performed for more than 10 seconds, the Manual Navigation mode is cancelled
and returns to the previous display.
Restarting current track
This function allows user to play the beginning of
the current song again.
1. Press the [1] button to move to the beginning
of the current track.
! CAUTION
Track will be automatically restarted after
telephone interrupt, audio streaming, DCP
flipped and power cycle.
2. Press and hold [BND] button for 1.5 seconds
or longer to play the first track of the memory
card.
Note:
These operations will cancel Track Repeat play and
all Random modes.
Special playback functions
By default, all special playback functions are
turned off and “
” will be displayed.
All the special playback functions will be memorized once activated (except Track repeat play)
even after power off.
Repeat mode
Track repeat play
This function allows you to play the current track
repeatedly.
1. Press the [RPT] button to perform track repeat
play.
2. Press the [RPT] button again to cancel track
repeat play.
The “
” indicator lights in the display when
track repeat play is enabled.
Note:
Any track/folder selection, card changing and power
cycle will cancel track repeat play.
Folder repeat play
This function allows you to play all tracks in the
current folder repeatedly.
1. Press and hold the [RPT] button for 1.5 seconds or longer to perform folder repeat play.
“RPT FLDR ON” will be displayed briefly.
2. Press and hold the [RPT] button for 1.5 seconds or longer to cancel folder repeat play.
“RPT FLDR OFF” will be displayed briefly.
18
FB278RBT
The “
” indicator lights in the display when
folder repeat play is enabled.
Note:
This function will cancel other previous special playback functions such as track repeat and Random
mode.
Random mode
There are 3 types of Random mode. When the
[RDM] button is pressed at the first time, the current Random mode will be displayed. Further
pressing the [RDM] button will switch the Random mode in the following order:
“RDM TRACK”
“RDM FOLDER”
“RDM CARD”
“RDM OFF”
The “
” indicator lights in the display.
Track random play
This function allows you to play the tracks of current folder randomly.
1. Press the [ RDM ] button to select “RDM
TRACK”.
Notes:
It will go to next folder after all the tracks in that
folder have been played. However, this will depend
on folder repeat setting.
Card random play
This function allows you to play all the tracks of
all the folders in a random order.
English
MP3 Operations
1. Press the [ RDM ] button to select “RDM
CARD”.
Notes:
This function will require some amount of time
depends on the complexity of folder hierarchy.
Always use the folder hierarchy as recommened in
chapter “Folder structure” on page 14 for optimal
performance.
Any track/folder selection will always perform as
next random track/folder.
To cancel random play
1. Press the [ RDM ] button to select “RDM
OFF”.
Quick random folder play
This function will perform a single jump to a random folder but do not affect current Random or
Folder Repeat settings.
1. Press and hold the [ RDM ] button for 1.5
seconds or longer to perform quick random
folder play.
Special playback priority
The icon will be displayed according to the selected special playback with the following priorities. It will return to previous special playback
setting after the current special playback function
is turned off.
Any track/folder selection will always perform as
next random track/folder.
Folder random play
This function allows you to play all the tracks alphabetically in a random folder.
1. Press the [ RDM ] button to select “RDM
FOLDER”.
Note:
This function will require some amount of time
depends on the complexity of folder hierarchy.
Always use the folder hierarchy as recommened in
chapter “Folder structure” on page 14 for optimal
performance.
FB278RBT
19
English
Introduction to Bluetooth® Wireless Technology
What is Bluetooth® wireless
technology?
Bluetooth wireless technology is a radio technology that connects devices, such as mobile
phones and headsets, without wires or cords
over a short distance of approximately 10 meters
(approx. 33 feet). Get more information at www.
bluetooth.com.
®
What is Bluetooth® wireless
profiles?
Bluetooth® wireless profiles are the different ways
that Bluetooth® devices communicate with other
devices. Bluetooth® phones normally support the
hands-free profile (HFP). In order to support a
certain profiles, a phone manufacturer must
implement certain mandatory features within the
phoneʼs software. The followings are the currently supported profiles for the main unit:
Hands-Free Profile (HFP)
This is commonly used to allow car hands-free
kits to communicate with mobile phones in the
car. The Bluetooth® car kits allow users with Bluetooth-equipped mobile phones to make use of
some of the phoneʼs features.
Advanced Audio Distribution Profile
(A2DP)
What is pairing?
With a mobile phone featuring Bluetooth® technology, you must ʻpairʼ the main unit with the
phone/Bluetooth® audio device before you use it
for the first time.
Pairing creates a unique and encrypted link between two Bluetooth® devices and lets them communicate with each other eliminating the need
to repeat the pairing process during future use.
Bluetooth® devices will not work if the devices
have not been paired. This car stereo is able to
hold up to 8 devices of pairing information.
What is passkey?
Passkey or PIN is a code that you enter on your
mobile phone to pair it with the main unit. This
makes your phone/Bluetooth® audio device and
the main unit recognizes each other and automatically works together. The default passkey for
this unit is ʻ0000ʼ.
Pairing with a mobile phone
1. Enable pairing mode in the car stereo. Please
refer “Adding a new device (Pairing mode)”
on page 28 for more details.
2. Activate Bluetooth® on your mobile phone.
Please check your mobile phone ownerʼs
manual for further details.
This allows you to send CD quality stereo music
from external audio player to car stereo without
wires. A2DP is able to provide crystal clear music
without the hassle of plugging cables. Bluetooth®
Wireless Technology with A2DP makes mobile
phones, pdaʼs and computers capable of streaming music.
4. When attempting to connect to the car stereo,
the mobile phone will prompt for a passkey,
enter the PIN: ʻ0000ʼ.
Audio Video Remote Control Profile
(AVRCP)
This enables music from Bluetooth® audio player
5. Device name will be displayed for editing after
successful pairing. Please refer “Editing a
device name” step 3 onwards on page 29 for
more details.
to be controlled remotely. AVRCP allows some
basic playback control functions such as play/
pause, volume up/down and next/previous track
to a Bluetooth® audio player.
20
FB278RBT
3. Search for new Bluetooth® device on the mobile
phone. The car stereoʼs name is ʻCLARION_
FB275ʼ.
6. The display returns to previous mode after a
few seconds.
7. Any incoming call will be automatically diverted
to the car stereo once connection is established.
Notes:
Please make sure your mobile phone supports the
HFP profile.
Please refer chapter “Audio Streaming Operations” on page 24 for music streaming functionality.
Always make sure the Bluetooth® Operation mode
in the phone is on when using this car handsfree.
Please refer “Bluetooth® adjustment” on page
28 for other Bluetooth® related adjustment.
Any further connection attempts by other devices
to connect as HFP partner are rejected until the
current device is disconnected. Please refer your
mobile phone ownerʼs manual for disconnecting
device.
Connecting Bluetooth® device
Up to the first 8 characters of device name can
be supported. If device name is not obtained,
Bluetooth® address of the device will be used as
default.
Please refer chapter “Handsfree Operations” on
page 22 for telephone function.
Pairing with an external Bluetooth®
audio player (A2DP support)
1. Enable pairing mode in the car stereo. Please
refer “Adding a new device (Pairing mode)”
on page 28 for more details.
2. Set the Bluetooth audio player in Pairing
mode. Please check your audio player ownerʼs
manual for further details.
®
3. The display automatically switches to BT Audio
mode and start playing music upon successfully pairing and connection. Connection can
be established in any source mode.
Notes:
Please make sure your Bluetooth® audio player
supports the A2DP and AVRCP profiles.
Any further connection attempts by other devices
to connect as A2DP/AVRCP partner are rejected
until the current device is disconnected.
You do not have to enter a dedicated pin code
for pairing these two devices (Only applicable to
Clarion products such as Aux Bluetooth® Transmitter), as you do with a mobile phone. However, for
other A2DP devices, you may need to enter “0000”
for the pin code in those devices.
The same device may connect as both A2DP/
AVRCP and HFP partner. This normally happens
to mobile phone with wireless music streaming
capability. However, using the same device will
cause the A2DP/AVRCP to be disconnected when
there is an incoming call or making a call. User may
need to manually resume playback via audio player
in phone depends on the type of phones. However,
some phones will automatically resume to BT Audio
mode after telephone interrupt.
English
Introduction to Bluetooth® Wireless Technology
Your device/phone will normally connect automatically to the unit after pairing. However, some
phones will not allow automatic connection to the
unit after pairing; please use the phone to manually connect to the unit.
If Automatic Connection is enabled in Adjustment
mode, the unit will try to connect to the previously connected phone when entering Telephone
mode or during power up. Connection can be
established at any Source mode. If connection
is unsuccessful, automatic connection will stop.
Please refer “Automatic connection” on page
29 to enable this feature.
The “
” indicator will light on upon successful
connection.
Notes:
Auto connection only works for HFP. User may need
to manually connect for A2DP. This will depends on
the Bluetooth® audio player.
Please connect HFP to unit before audio streaming.
It is recommended to use one device at one time
as using 2 different devices in the same time may
affect the normal operation.
Disconnecting Bluetooth® device
] button for 1.5 sec1. Press and hold the [
onds or longer to disconnect all Bluetooth®
devices.
“CLOSING CONNECTIONS” will be displayed
and “
” indicator lights off.
Notes:
Turning off the unit power and deleting any
Bluetooth® device in Adjustment mode will also
disconnect the current device.
Alternatively, user can use the phone to manually
disconnect the device. However some devices will
automatically reconnect once disconnect. Please
refer your device owner's manual for more details.
Please refer “Compatible Devices” on page 30
to make sure your device is compatible.
FB278RBT
21
English
Handsfree Operations
Storing a preset telephone numbers
This function allows you to make direct call from
the unit. There are 6 preset telephone numbers
can be stored in the unit.
! CAUTION
Please avoid performing this operation while
you are driving as you may lose your concentration on the road. Always be sure to park
your vehicle and apply the parking brake in
order to perform this operation.
Telephone numbers edit mode
1. Press the [
mode.
] button to enter Telephone
] button to select
2. Press the [
,
“MEMORY 1” to “MEMORY 6”.
] knob to edit the num3. Push the [
bers. A blinking cursor on current digit will be
displayed.
4. Turn the [
ber.
5. Push the [
number input.
] knob to select a num] knob to go to next
] knob at a blank or
6. Push the [
the last 16th digit (“
” indicator will be displayed) will store the numbers into memory.
Notes:
“+” can be allowed in the first digit only.
Maximum digit range: 16 digits.
] knob for 1.5
Push and hold the [
seconds or longer at a non-blank digit will store the
numbers into memory as well.
] button at anytime will cancel current
Press the [
operation and exit the Edit mode without saving the
numbers. If no operation is performed for more than
10 seconds, the Edit mode is cancelled and returns
to the previous display.
Clearing all digits
1. During Telephone Numbers Edit mode, turn the
[
] knob to select a blank digit.
] knob for
2. Push and hold the [
1.5 seconds or longer to clear all digits on the
right side.
Note:
Digits on the left side will remain as it is. In order to
clear all the digits, always select the first character
and perform the above operation.
22
FB278RBT
Deleting a digit
1. During Telephone Numbers Edit mode, turn the
[
] knob to select a blank digit.
2. Push the [
rent digit.
] knob to delete cur-
Note:
Digits on the right side (if there is any) will be shifted
to the left.
Incoming call
Whenever your car stereo is operating, the car
stereo is in standby mode awaiting the next call,
when an incoming call arrives the car stereo will
mute automatically and the ring tone is reproduced through your carʼs speaker.
The Car stereo will temporarily switch to Telephone Interrupt mode and caller ID will be displayed in the car stereo.
Notes:
Car stereo will be automatically set as default
speaker output everytime when there is an incoming call.
Some phones choose to present the audio despite
being told to route it to the car stereo. This duplication of audio is a device problem/feature but does
not impair functionality.
During incoming call, caller ID and “Calling...” will
be displayed. Caller ID and CLIP (Calling Line
Identification Presentation) is dependent on mobile
phone and service provider. However, incoming call
with private telephone numbers (CLIR- Calling Line
Identification Restriction) will not be displayed.
Answering a call
User can answer an incoming call directly from
the car stereo.
1. Press the [
call.
] button to pick up an incoming
2. The display switch to Telephone Interrupt mode.
Notes:
During conversation, “
will be displayed.
” and call time elapsed
During an incoming call, some phones may automatically pick up the call when it connects to this
unit.
Rejecting a call
This function allows you to reject an incoming
call directly from the car stereo.
1. Press the [
call.
] button to reject an incoming
2. The display returns to previous mode.
Ending a call
This function allows you to end a call conversation directly from the car stereo.
1. Press the [
] button to end the call.
2. The display returns to previous mode.
Note:
“CALL END” will be displayed when ending a
conversation.
Alternatively, you may also answer/reject/end the
call by using your phoneʼs keypad. However, it
is recommended to always perform those operations from the main unit.
Making a call
There are few ways to make outgoing call.
If no phone is connected, the car stereo will not
be able to make an outgoing call. The car stereo
will try to reconnect to the last connected device if
Auto Connection is enabled in Adjustment mode.
This is dependent on mobile phones.
Please make sure your phone is connected with
the “
” indicator light is on.
There are 2 display icons at the top row of display when entering Telephone mode.
: Call can be activated.
: Call cannot be activated. Please connect
your phone.
Notes:
This is dependent on mobile phone. Please make
sure your mobile phone supports voice dialing in
order to use this feature. Please refer to your mobile
phone ownerʼs manual if this function is supported.
“CALL FAIL” will be displayed if it is not supported
or the call is unsuccessful.
Please use an external microphone (optional) for
better voice reception if necessary.
Call via last dialed number (Redial)
A call can be made with the last number dialed.
When the phone is connected, redial can be
performed according to the phone last dialed
number. Each phone has its own redial number.
If thereʼs no redial number, operation will not be
performed.
2-1. Select “LN REDIAL”
] button again to redial the last
3-1. Press the [
dialed number.
Call via preset telephone numbers
2-1. Select “MEMORY 1” to “MEMORY 6”.
3-1. Press the [
] button again to make call.
Alternatively, user can make outgoing call directly
by pressing the corresponding preset telephone
numbers.
1. Press the [
mode.
] button to enter Telephone
1. Press the [
mode.
] button to enter Telephone
2. Press the corresponding [DIRECT] button to
make outgoing call.
2. Press the [
,
] to select the following
Note:
The preset telephone numbers will be the same for
all paired devices.
“LN REDIAL”
“MEMORY 2”
“MEMORY 4”
“MEMORY 6”
“VOICEDIAL”
“MEMORY 1”
“MEMORY 3”
“MEMORY 5”
3. Press the [
ing call.
] button again to perform outgo-
Note:
“Dialing” will be displayed when making a call.
Telephone numbers will be displayed if using the
preset telephone numbers dialing.
Call via voice dialing
2-1. Select “VOICEDIAL”
3-1. Press the [
voice dialing.
] button again to activate
English
Handsfree Operations
Alternatively, you may also make a call by using your phoneʼs keypad. However, it is recommended to always make a call from the main unit
as some phones may not work well using the
phoneʼs keypad with this unit.
Microphone
The unit is fitted with an internal microphone that
should provide acceptable performance when
fitted to vehicles with low levels of background
noise. For optimum performance Clarion recommends the use of an external microphone fitted
as near as possible to the driver.
3-2. Speak the contact name clearly towards the
internal/external microphone to perform voice
dialing.
FB278RBT
23
English
Handsfree Operations
Audio Streaming Operations
Please refer “Selecting microphone input” on
page 29 for switching to internal/external the microphone.
Note:
Be sure to read the chapter “Pairing with an external Bluetooth® audio player (A2DP support)”
before proceeding.
What is audio streaming?
Audio streaming is a technique for transferring
audio data such that it can be processed as a
steady and continuous stream.
Users can stream music from their external audio
player to their car stereo wirelessly and listen to
the tracks through the carʼs speakers.
Please consult your nearest Clarion dealer for
more information on the product of wireless audio streaming transmitter offered.
Handfree volume
The unit implements an acoustic echo canceller
to reduce the echo heard by the remote caller.
Under normal circumstances the unit operates in
full-duplex mode meaning that both parties can
speak at the same time.
If the volume in the vehicle is set too high, the
echo canceller will revert to half-duplex mode
when only one party can talk at a time. The volume should be adjusted to be just loud enough.
The unit also implements Noise Dependent Volume that increases the volume as the noise in
the vehicle increases.
Adjusting the volume for handsfree
] knob clockwise inTurning the [
creases the volume; turning it counterclockwise
decreases the volume.
“VOLUME 1” to “VOLUME 16” will be displayed
depends on the volume level.
∗ Factory default setting for volume is “VOLUME
8”.
When the unit is connected to a mobile phone
and a call is in progress, turning off the vehicle
ignition key (“ACC” or ACCESSORY) switch will
not end the call. The unit will remain active until the call has ended at which point the unit will
power OFF. It is therefore safe to pull over and
stop the engine during a call without the inconvenience of dropping the call.
24
FB278RBT
! CAUTION
Please avoid operating your connected
mobile phone while audio streaming as this
may cause noise or sound choppy on the
song playback.
Audio streaming may or may not resume
after telephone interrupt as this is dependent on mobile phone.
System will always return to Radio mode if
audio streaming is disconnected.
Play/Pause a track
] knob to pause play.
1. Push the [
“ ” appears in the display.
2. To resume track play, push the [
knob again. “
” appears in the display.
]
Notes:
During music streaming playback, “STREAMING...”
will be shown on the display. Information about
tracks (e.g. the elapsed playtime, song title, etc.)
cannot be displayed on this unit.
When A2DP device is disconnected, “NO STREAM”
will be shown on the display and return to Radio
mode.
Some Bluetooth® audio players may not have play/
pause synchronized with this unit. Please make
sure both device and main unit are in the same
play/pause status in BT AUDIO mode.
Common Operations
Selecting a track
Adjustment mode
Track-up
] button to move to the begin1. Press the [
ning of the next track.
] button is pressed, play2. Each time the [
back proceeds to another track in the advancing direction.
Track-down
] button to move the to begin1. Press the [
ning of the previous track.
] button is pressed, play2. Each time the [
back proceeds to previous track in the reverse
direction.
Notes:
Playing order will depend on Bluetooth® audio
player.
] button is pressed, some A2DP deWhen [
vices will restart the current track depends on the
duration of playback.
There are 6 categories of Adjusment mode:
Audio mode
(Bass, Treble, Balance, Fader and Loudness)
English
Audio Streaming Operations
Additional Source mode (AUX Input)
RDS Adjustment mode (Alternate Frequency)
Clock∗ Adjustment mode
Display∗ Adjustment mode
Bluetooth®∗ Adjustment mode
∗ Item that has 2nd level adjustment
During Telephone/TA Interrupt mode, only Balance and Fader can be adjusted. Adjustment
mode is unaccessible during Telephone mode
and vice versa.
1 . Press and hold the [DISP] button for 1.5 seconds or longer to enter the adjustment selection
display.
2 . Press the [
name”.
,
] button to select the “item
“BASS”
“TREBLE”
“BALANCE”
“FADER”
“LOUDNESS”
“AUX INPUT”
“AF”
“CLOCK”
“DISPLAY”
“BLUETOOTH”
] knob to enter 2nd
3 . Push the [
]
level adjustment or turn the [
knob to select the “desired setting value”
depends on the selected item.
Notes:
A“
” will be displayed and “
” will light on
when an item has 2nd level adjustment.
]
After completing settings, press and hold the [
button for 1.5 seconds or longer to return to the
previous mode.
If no operation is performed for more than 10
seconds, the Adjustment mode is cancelled and
returns to the previous display.
Audio mode
Adjusting the bass
2-1.
Select “BASS”.
3-1.
] knob clockwise
Turn the [
emphasizes the bass; turning it counterclockwise attenuates the bass.
Notes:
The factory default setting is “0”.
The value range is -7 to +7.
FB278RBT
25
English
Common Operations
Adjusting the treble
2-1.
Select “TREBLE”.
3-1.
] knob clockwise emphaTurn [
sizes the treble; turning it counterclockwise
attenuates the treble.
Notes:
The factory default setting is “0”.
The value range is -7 to +7.
Adjusting the balance
2-1.
Select “BALANCE”.
3-1.
] knob clockwise
Turn the [
emphasizes the sound from the right speaker; turning it counterclockwise emphasizes
the sound from the left speaker.
The display changes as follows:
“RIGHT XX” will be displayed where “XX” is
the value from 1 to 12.
“LEFT XX” will be displayed where “XX” is
the value from 1 to 12.
Notes:
When Balance is 0, “CENTRE” will be displayed
instead.
The factory default setting is “CENTRE”.
Adjusting the fader
2-1.
Select “FADER”.
3-1.
] knob clockwise emTurn the [
phasizes the sound from the front speakers;
turning it counterclockwise emphasizes the
sound from the rear speakers.
The display changes as follows:
“FRONT XX” will be displayed where “XX” is
the value from 1 to 12.
“REAR XX” will be displayed where “XX” is
the value from 1 to 12.
Notes:
When Fader is 0, “CENTRE” will be displayed
instead.
The factory default setting is “CENTRE”.
Adjusting the loudness
The loudness effect does not adjust the low
sound area like the normal sound adjustment
function, but emphasizes the deep bass sound
area to provide you with a dynamic sound.
26
FB278RBT
2-1.
Select “LOUDNESS”.
3-1.
Turn the [
or “OFF”.
ON
] knob to select “ON”
: Loudness effect enabled.
OFF : Loudness effect disabled.
Note:
The factory default setting is “OFF”.
Setting AUX function
This option allows user to enable or disable the
AUX function. AUX function will be available in
source mode selection if turned on. Otherwise, it
will be hidden from the source mode selection.
2-1.
Select “AUX INPUT”.
3-1.
Turn the [
or “OFF”.
ON
] knob to select “ON”
: Aux function is turned on.
OFF : Aux function is turned off.
Note:
The factory default setting is “OFF”.
AF function
The AF function switches to a different frequency
on the same network in order to maintain optimum reception.
2-1.
Select “AF”.
3-1.
Turn the [
or “OFF”.
ON
] knob to select “ON”
: AF turns on.
OFF : AF turns off.
Note:
The factory default setting is “ON”.
Clock adjustment
2-1.
Select “CLOCK”.
3-1.
Push the [
3-2.
Press the [
“item name”.
] knob.
,
] button to select the
Adjusting the clock
“CLK EN”
This adjustment allows the clock to be set by
user.
“CLK MODE”
1. Select “CLK SET”.
“CLK SET”
3-3.
2. Push the [
Push or turn the [
pends on selected item.
] knob de-
Setting the clock enable
This setting allows the clock to be displayed at
the bottom of display in all source modes.
1. Select “CLK EN”.
2. Turn the [
options.
“OFF”
] knob to select the
“ON”
“RDS”
] knob.
3. Press the [
,
hour or the minute.
4. Turn the [
rect time.
5. Press the [
] button to exit the setting.
Notes:
The factory default setting is “00:00” for 24 hour
mode.
The clock is updated in realtime.
Display adjustment
: Clock is enabled and manually set by
user.
Press the [
“DISPLAY”.
3-1.
RDS : Clock is enabled and will automatic synchronize to CT data from RDS station.
Push the [
level adjustment.
3-2.
Press the [
“item name”.
Notes:
The factory default setting is “OFF”.
,
,
“CONTRAST”
CT data is not transmitted in some countries and
by some broadcast stations. Also, in some areas,
the CT display may not accurate.
“ILLUM”
Setting the clock mode
“24 HR”
12 HR : 12 hour mode.
24 HR : 24 hour mode.
Note:
The factory default setting is “24 HR”.
] button to select the
“USER COL”
“ANIMATION”
1. Select “CLK MODE”.
“12 HR”
] knob to enter next
“COLOUR”
This setting allows user to select either 12 or 24
hour system.
] knob to select the
] button and select
“SCROLL”
If a CT data is not being received, “--:--” appears
at the bottom of the display.
2. Turn the [
options.
] button to select the
] knob to set the cor-
2-1.
OFF : Clock is disabled.
ON
English
Common Operations
3-3.
Push or turn the [
pends on selected item.
] knob de-
Setting the method for title scroll
Set how to scroll in MP3 title.
∗ The factory default setting is “ON”.
1. Select “SCROLL”.
2. Turn the [
or “OFF”.
] knob to select “ON”
ON : To scroll continunously.
OFF : Scroll function is disabled. It will only
scroll for once.
FB278RBT
27
English
Common Operations
Adjusting the display contrast
Setting the animation effect
You can adjust the display contrast to match the
angle of installation of the unit.
You can turn on or off the animation effect in this
unit.
∗ The factory default setting is “9”.
(Adjustment level: 0 to 14)
1. Select “ANIMATION”.
1. Select “CONTRAST”.
2. Turn the [
contrast.
] knob to adjust the
Adjusting the display and line illumination
You can adjust the display illuminations (Display
backlight intensity) at night (key illumination on).
The adjustment level is from 1 to 9.
2. Turn the [
or “OFF”.
] knob to select “ON”
: Welcome animation and screen wipe
transition at Source mode are enabled.
OFF : Animation effect is disabled.
ON
Bluetooth adjustment
®
2-1.
∗ The factory default setting for key illumination on
is “3”.
Press the [
,
“BLUETOOTH”.
3-1.
1. Select “ILLUM”.
Push the [
3-2.
Press the [
“item name”.
2. Turn the [
illumination.
] knob to adjust the
“DEL. DEV.”
Setting the colour line illumination
“AUTO CONN”
1. Select “COLOUR”.
Setting user colour mode
1. Select “USER COL”.
2. Turn the [
setting.
] knob to enter the
] button to move the
3. Press the [
,
cursor for adjusting the R, G or B value. The
value of R is adjustable by default.
] knob to select from 0
4. Turn the [
to 8. Adjustment will be updated in realtime.
Note:
The factory default setting for user colour R, G and
B (R: red, G: green, B: blue) are “8”.
28
FB278RBT
] button to select the
“EDIT DEV.”
Display illumination is fixed at “9” for key illumination
off (Daytime). “N/A” will be displayed.
COL. SCAN
OFF
BLUE
SURF BLUE
WHITE
AQUA
GREEN
LIME
ORANGE
RED
PINK
PALE PINK
VIOLET
PURPLE
COL. SCAN ...
] knob.
,
“ADD DEV.”
Notes:
The new settings will be stored in memory.
] knob to select the
2. Turn the [
colour, the type changes in the following orders:
] button and select
“MIC”
3-3.
Push or turn the [
depends on selected item.
] knob
Adding a new device (Pairing mode)
1. Select “ADD DEV.”.
2. Push the [
] knob.
∗ The “
” indicator will be blinking. The display
shows “Pairing...” and the car stereo is currently
in Pairing mode.
Note:
The pairing timeout is 3 minutes.
Editing a device name
Automatic connection
1. Select “EDIT DEV.”.
] knob to select a
2. Turn the [
device name to be edited.
3. Push the [
] knob.
∗ The display shows the device name.
This function allows the unit to be connected automatically with previously connected device during power up or entering Telephone mode. The
Bluetooth® wireless function in your phone has to
be turned on to establish automatic connection.
1. Select “AUTO CONN”.
2. Turn the [
or “OFF”.
ON
4. Turn the [
acter.
] knob to edit a char-
] button or push [
5. Press the [
knob to go to next character. Press the [
button to return to previous character.
]
]
] knob at the last blank
6. Push the [
character to store the name.
Notes:
] knob for 1.5
Push and hold the [
seconds or longer at any position will store the
name as well.
If there is no device connected, “(no devices)” will
be shown in the display.
3. Push the [
firmation is prompted.
] knob to select “ON”
: Auto connection enabled.
OFF : Auto connection disabled.
Notes:
The factory default setting is “OFF”.
Please enable this feature only if your phone is
supported.
Selecting microphone input
1. Select “MIC”.
2. Turn the [
the following:
] knob to select one of
INTERNAL : Built-in microphone will be used.
EXTERNAL : An external microphone will be
used.
Note:
The factory default setting is “INTERNAL”.
Deleting a device
1. Select “DEL. DEV.”.
2. Turn the [
to be deleted.
English
Common Operations
] knob to select a device
] knob. A delete con-
4. Turn the [
or “NO”.
] knob to select “YES”
5. Push the [
selection.
] knob to confirm the
Notes:
If there is no device connected, “(no devices)” will
be shown in the display.
“All” option will be available if there is more than
one device connected.
System Menu
] and [
] buttons si1. Press and hold [
multaneously for 1.5 seconds or longer.
2. Press the [
“VERSION”
3. Press the [
] button to select an item.
,
“FACT. RST”
] button to exit the menu.
Checking the unit version
2-1. Select “VERSION”.
Deleting pairing information in the main unit only
stops the unit from being connect to the other device. It does not stop the other device from trying
to connect to main unit. Please delete the pairing
information of the main unit from the phone/device
as well. Always make sure pairing information on
both device and main unit have been deleted before
starting a new pairing activity.
Deleting a device will disconnect any current
Bluetooth® connection. User will need to manually
re-connect if necessary.
FB278RBT
29
English
Compatible Devices
Common Operations
Restoring to factory default setting
This function allows user to restore the unit to the
factory default setting.
2-1. Select “FACT. RST”.
2-2. Push the [
firmation is prompted.
] knob. A reset con-
2-3. Turn the [
or “NO”.
] knob to select “YES”
2-4. Push the [
selection.
] knob to confirm the
Notes:
All pairing information and preset memories will be
cleared. User will have to manually perform those
setting again.
Once reset, system will automatically turn off and
re-power on.
Clock time will not be reset with this operation.
The clock time reset is done with the following
steps.
1. Turn off the power.
2. Press the [RELEASE] button and remove the
DCP.
3. Press the reset button with a thin rod.
30
FB278RBT
Supported phones with Bluetooth
wireless technology
®
Make sure your mobile phone supports the following Bluetooth® profile:
- HFP (Handsfree for mobile phone)
Optional profiles for audio streaming in mobile
phone:
- A2DP (Stereo music streaming)
- AVRCP (Remote control function)
Please check your phoneʼs specification for supported profiles. Features supported for each profile vary from product to product. To ensure your
device will work correctly with this unit, please
consult your nearest Clarion dealer for your
phone compatibilities.
Supported external audio player
with Bluetooth® wireless technology
This car stereo is compatible with Clarion
Bluetooth® Audio Transmitter (DGL370/373) and
Cradle for iPod (BC001N/BC002M/BC003V).
Please consult your nearest Clarion dealer for
the product offer.
Operation is not guaranteed with all the Bluetooth®
audio players that supports A2DP/AVRCP from
other manufacturers.
Safe and efficient use
Note:
Read this information before using your car stereo.
Changes or modifications to this product not expressly approved by Clarion may void the userʼs
authority to operate the equipment.
Please check for any exceptions, due to national
requirements or limitations, in usage of equipment with Bluetooth® wirelesss technology before using this product.
Product care
Do not expose your product to liquid or moisture or to humidity.
Do not expose your product to extreme high or
low temperatures.
Do not expose your product to lit candles,
cigarettes, or cigars, or to open flames etc.
Do not drop, throw or try to bend the product
as rough treatment could damage it.
Do not use any other accessories than Clarion
originals intended for use with this product. Use
of non-original accessories may result in loss
of performance, damage to the product, fire,
electric shock or injury. The warranty does not
cover product failures which have been caused
by use of non-original accessories.
Do not attempt to disassemble your product.
The product does not contain consumer serviceable or replaceable components. Only
Clarion service partners should perform service.
Do not keep the product in an area prone to
dust and dirt. Only use a soft damp cloth to
clean your product.
If you will not be using the product for a while,
store it in a place that is dry, free from damp,
dust and extreme temperatures.
To reduce risk of electric shock, unplug the
unit from any power source before attempting
to clean it.
Installation
Please note that only authorized personnel
should install the car stereo. Please check with
your car dealer for recommendations on professional installation engineers. Check with your car
manufacturerʼs representative to be sure that all
equipment for the car stereo, including additional
accessories, is placed in a safe location. If your
car is equipped with an air bag, check that the
handsfree equipment does not interfere with its
function.
English
7. ADDITIONAL INFORMATION
The car stereo is made for use in cars with a 12
volt electrical system. Other supply voltages may
cause damage to the equipment.
Radio frequency exposure
Your car stereo is a radio transmitter and receiver. When in operation, it communicates with
a mobile device featuring Bluetooth® wireless
technology by receiving and transmitting radio
frequency (RF) electromagnetic fields (microwaves) in the frequency range 2400 to 2500
MHz. The output power of the radio transmitter
is low, 0.001 watt.
Your car stereo is designed to operate in compliance with the RF exposure guidelines and limits
set by national authorities and international health
agencies when used with any compatible mobile
phone with Bluetooth® wireless technology.
Driving
Check the laws and regulations on the use of
mobile phones and handsfree equipment in the
areas where you drive.
Always give full attention to driving and pull off
the road and park before making or answering a
call if driving conditions so require.
RF energy may affect some electronic systems in
motor vehicles such as car stereo, safety equipment etc. Check with your vehicle manufacturerʼs
representative to be sure that your mobile phone
or car handsfree receiver will not affect the electronic systems in your vehicle.
FB278RBT
31
English
Additional Information
Electronic equipment
Most modern electronic equipment is shielded
from RF energy. However, certain electronic
equipment is not, therefore:
Do not use your car stereo near medical equipment without requesting permission. If you are
using any personal medical devices, e.g. a
pacemaker or a hearing aid, please read in your
mobile phoneʼs Userʼs Guide for further information.
Blasting areas
Turn off all your electronic devices when in a
blasting area or in areas posted turn off two-way
radio to avoid interfering with blasting operations.
Construction crews often use remote control RF
devices to set off explosives.
Potentially explosive atmospheres
Turn off your electronic device when in any area
with a potentially explosive atmosphere. It is rare,
but your electronic device could generate sparks.
Sparks in such areas could cause an explosion
or fire resulting in bodily injury or even death.
Areas with a potentially explosive atmosphere
are often, but not always, clearly marked.
Emergency calls
IMPORTANT!
This car stereo, and the electronic device connected
to the handsfree operate using radio signals, cellular,
bluetooth wireless technology and landline networks
as well as user-programmed functions, which cannot
guarantee connection under all conditions. Therefore
you should never rely solely upon any electronic
device for essential communications (e.g. medical
emergencies).
Remember, in order to make or receive calls, the
car stereo and the electronic device connected to
the handsfree must be switched on and in a service
area with adequate cellular signal strength. Emergency calls may not be possible on all cellular phone
networks or when certain network services and/or
phone features are in use. Check with your local
service provider.
32
FB278RBT
Problem
Cause
Replace with a fuse of the same amperage.
If the fuse blows again, consult your store of
purchase.
Incorrect wiring.
Consult your store of purchase.
No sound output when
operating the unit with
amplifiers or power
antenna attached.
Power antenna lead is
shorted to ground or
excessive current is
required for remote-on
the amplifiers or power
antenna.
1. Turn the unit off.
2. Remove all wires attached to the power
antenna lead. Check each wire for a
possible short to ground using an ohm
meter.
3. Turn the unit back on.
4. Reconnect each amplifier remote wire to
the power antenna lead one by one. If
the amplifiers turn off before all wires are
attached, use an external relay to provide
remote-on voltage (excessive current
required).
Nothing happens when
button are pressed.
Display is not accurate.
The microprocessor has
malfunctioned due to
noise, etc.
Perform factory restore. Please refer “Restoring
to factory default setting” on page 30 for
more details.
No sound heard.
The speaker protection
circuit is operating.
1. Turn down sound volume. Function can
also be restored by turning the power off
and on again. (Speaker volume is reduced
automatically when the speaker protection
circuit operates).
2. If the sound is muted again, consult our
service department.
Problem
No sound heard.
SD memory card
Measure
Fuse is blown.
General
Power does not turn on.
(No sound is produced)
Cause
Measure
MP3 files are absent in a
SD memory card.
Write MP3 files onto the SD memory card
properly.
Files are not recognized
as an MP3 file.
Use MP3 files encoded properly.
Sound is cut or skipped.
Noise is generated or
noise is mixed with
sound.
MP3 files are not
encoded properly.
Use MP3 files encoded properly.
SD/MMC memory card
is not readable.
File system format is not
correct.
Format SD memory card as FAT12 or FAT16.
Incompatible SD/MMC.
Please make sure your SD/MMC is supported
or consult your nearest Clarion dealer for SD/
MMC compatibility.
Those MP3 files may
be corrupted or do not
encoded properly.
Use MP3 files encoded properly.
MP3 files are unable
to playback, display
remains pause or
loading.
English
8. TROUBLESHOOTING
FB278RBT
33
Problem
BT audio
English
TROUBLESHOOTING
Cause
Measure
Audio streaming is
disconnected after
telephone interrupt.
This is probably happen
when audio streaming
and telephone function
are from the same
device (mobile phone).
Audio streaming may or
may not resume after
interruption as this is
highly dependent on the
device/phone.
Reconnect A2DP/AVRCP (Audio streaming
profiles) from the phone again after telephone
interrupt.
Use Clarion recommends external audio
player with Bluetooth® wireless technology.
I cannot perform
remote control for audio
streaming.
AVRCP is not connected.
Disconnect and re-connect the device again.
If problem persists, please delete pairing
information on both device and main unit
before re-pairing.
Audio streaming
becomes choppy when
using your connected
phone.
Due to excessive
Bluetooth® activity on a
low bandwidth link. Some
phones will not handle
this well.
If your phone is facing this problem, please
avoid touching the phone's keypad while
audio streaming.
You may pause the audio streaming before
operating your phone.
Display is showing
“STREAMING...” but
there is no sound
output.
Some Bluetooth®
audio devices might
not support AVRCP.
Thus, play/pause is not
synchronized.
Check whether both device and main unit
are in play status. Change the status in the
device if necessary.
If problem persists, please power off and on
the main unit or the device.
There might be
connection links broken
between the devices.
Please delete pairing information on both
device and main unit and start re-pairing.
Due to excessive
Bluetooth® activity on
a low bandwidth link.
Some devices may affect
other devicesʼ normal
operation if both are
used at the same time.
Please disconnect the devices and connect
either one of the devices only. If the problem
persists, please consult you nearest Clarion
dealer for your phone compatibility.
When I use 2 different
devices at the same
time, sometimes audio
streaming or handsfree
operations are not
operating correctly.
34
FB278RBT
Problem
Cause
Measure
After pairing, car stereo
is not able to receive
and make calls.
Bluetooth® connection
is not established yet.
Normally it will take
several seconds to
establish the connection
after pairing.
Some phones will not
automatic connect after
pairing.
Use your phone to manually connect or enter
Telephone mode with Auto connection ON
(Car stereo will try to reconnect).
English
TROUBLESHOOTING
Power off and on the car stereo and perform
pairing again. Always make sure pairing
information on both device and main unit
have been deleted before starting a new
pairing activity.
Telephone
If the problem persists, please consult you
nearest Clarion dealer for your phone
compatibility.
Car stereo is connected
to other device.
Disconnect the previous device and reconnect
current device.
Unable to reconnect to
car stereo using phone.
The device pairing
information may have
been deleted from the
unit.
Please make sure the device is still in the
device list of the unit and perform the above
measure.
Callers voice sounds
distorted or is
intermittent.
Volume is too loud
(depends on the car
environment, speakers
and microphone) and
half-duplex mode is
automatically triggered.
Try reducing the telephone volume level.
Caller reports poor
voice quality at remote
end.
Use external rather than internal microphone.
Move external microphone closer to mouth.
Try reducing the telephone volume level.
Difficulties of pairing
and connecting with
phone during another
Bluetooth® operation
such as audio
streaming.
Due to excessive
Bluetooth® activity on
a low bandwidth link, it
may result hard to get
paired and connected.
Disconnect all devices. Try pairing with phone
first and connect A2DP device later.
There is no sound
output when incoming
call is answered.
Incoming call was
answered too quickly
before you hear the
ringing tone. This can
cause the audio not
properly transferred to
the main unit by some
phones.
Please use your phone to transfer the audio
back to the phone for the current ongoing call.
Kindly answer the call only when you hear a
ringing tone next time.
If the problem persists, please reconnect the
phone or create new pairing before the next
incoming call.
There is no sound
output during
conversation.
Bluetooth®
communication link is
lost.
Please disconnect the phone and reconnect.
If the problem persists, please create new
pairing for both phone and main unit.
Unable to receive and
make call in SD mode
when another A2DP
device is connected.
Due to excessive
Bluetooth® activity on
a low bandwidth link.
Some A2DP devices still
stream data to the unit.
Disconnect the A2DP device and reconnect
mobile phone (HFP). It is recommended to
connect and use one device at a time.
If the problem persists, please consult you
nearest Clarion dealer for your phone
compatibility.
FB278RBT
35
English
9. ERROR DISPLAYS
If an error occurs, one of the following displays is displayed.
Take the measures described below to eliminate the problem.
Error Display
NO MP3
SD ERROR
CALL FAIL
ERROR
STREAM ERR
36
FB278RBT
Cause
Measure
No audio file (MP3) is detected
in the media.
SD memory card format is not
supported.
Replace with audio contents loaded SD/
MMC card.
If the error message persists, please check
the SD memory card compatibility or format
the memory card as FAT12 or FAT16.
SD/MMC cannot be read,
SD memory card format is
corrupted or not supported.
Open the flip down panel, eject and reinsert
the card. Close the panel and try again.
If the error message persists, please check
the SD memory card compatibility or format
the memory card as FAT12 or FAT16.
Call is not made successfully.
Please try a few times or dial from phone if
necessary.
Voice dial feature is not
supported by the phone.
Voice dial cannot be activated.
This is dependent on phone.
Please make sure your phone supports
this feature or consult your nearest Clarion
dealer for voice dial compatibility.
Low level exception in
Bluetooth® communications.
The user may need to re-connect the phone
(if auto connect is off) and he will need to
reconnect any A2DP stream/ HFP.
Low level exception when
handling A2DP streams. It is
due interoperability issues
between the unit and the
streaming source.
The user may need to re-connect the phone
(if auto connect is off) and he will need to
reconnect any A2DP stream/ HFP.
If problem persists, the user will need to
switch off or use an alternative A2DP source.
FM tuner
Frequency Range: 87.5 MHz to 107.9 MHz
Usable Sensitivity: 11 dBf
50 dB Quieting Sensitivity: 17 dBf
Alternate Channel Selectivity: 75 dB
Stereo Separation (1 kHz): 35 dB
Frequency Response (±3 dB): 30 Hz to 15 kHz
SD player
English
10. SPECIFICATIONS
General
Power Supply Voltage:
12 V DC (10.8 V to 15.6 V allowable), negative
ground
Current Consumption: Less than 15 A
Speaker Impedance: 4 Ω (4 Ω to 8 Ω allowable)
Weight: 1.87 lb. (0.85 kg)
Dimensions:
178 mm Width X 50 mm Height X 154 mm
Depth
System: Multimedia audio system
Frequency Response: 10 Hz to 20 kHz (±3 dB)
Dynamic Range: 80 dB (1 kHz)
Harmonic Distortion: 0.01%
Bluetooth® wireless technology
Compliance: Bluetooth® 1.2
Frequency Range: 2.40~2.4835 GHz, ISM band
RF Power: Class 2 (2.5mW)
Profiles: HFP, A2DP, AVRCP
Operating Temperature: -20ºC ~ 60ºC
Telephone Operation:
Noise reduction, echo cancellation, full duplex
telephony
Mic Input (External): 2.2k ohm, 2V electret
Audio
Notes:
• Specifications comply with JEITA Standards.
• Specifications and design are subject to change
without notice for further improvement.
• Please make sure when connecting external power
amplifier, that you properly, to the car chassis,
ground the amplifier.
• If this is not done, severe damage to the source
unit may happen.
Maximum Power Output: 200 W (50 W X 4 ch)
Bass Control Action (100 Hz): ±14 dB
Treble Control Action (10 kHz): ±14 dB
Line Output (with A/C 1 kHz, 10 kΩ): 1.8 V
FB278RBT
37
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising