Yamaha EL-100 Owner's manual

PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from
electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not
limited to, the following:
Power supply/Power cord
Water warning
• Only use the voltage specified as correct for the instrument. The
required voltage is printed on the name plate of the instrument.
• Do not expose the instrument to rain, use it near water or in damp
or wet conditions, or place containers on it containing liquids
which might spill into any openings.
• Check the electric plug periodically and remove any dirt or dust
which may have accumulated on it.
• Never insert or remove an electric plug with wet hands.
• Use only the supplied power cord/plug.
• Do not place the power cord near heat sources such as heaters or
radiators, and do not excessively bend or otherwise damage the
cord, place heavy objects on it, or place it in a position where
anyone could walk on, trip over, or roll anything over it.
Fire warning
• Do not put burning items, such as candles, on the unit.
A burning item may fall over and cause a fire.
If you notice any abnormality
Do not open
• Do not open the instrument or attempt to disassemble the internal
parts or modify them in any way. The instrument contains no
user-serviceable parts. If it should appear to be malfunctioning,
discontinue use immediately and have it inspected by qualified
Yamaha service personnel.
• If the power cord or plug becomes frayed or damaged, or if there
is a sudden loss of sound during use of the instrument, or if any
unusual smells or smoke should appear to be caused by it,
immediately turn off the power switch, disconnect the electric plug
from the outlet, and have the instrument inspected by qualified
Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or
damage to the instrument or other property. These precautions include, but are not limited to, the following:
Power supply/Power cord
• When removing the electric plug from the instrument or an outlet,
always hold the plug itself and not the cord. Pulling by the cord
can damage it.
Assembly
• Remove the electric plug from the outlet when the instrument is
not to be used for extended periods of time, or during electrical
storms.
2
• Do not connect the instrument to an electrical outlet using a
multiple-connector. Doing so can result in lower sound quality, or
possibly cause overheating in the outlet.
• Read carefully the attached documentation explaining the
assembly process. Failure to assemble the instrument in the
proper sequence might result in damage to the instrument or even
injury.
(1)B-7
1/2
Location
• Never insert or drop paper, metallic, or other objects into the gaps
on the panel or keyboard. If this happens, turn off the power
immediately and unplug the power cord from the AC outlet. Then
have the instrument inspected by qualified Yamaha service
personnel.
• Do not expose the instrument to excessive dust or vibrations, or
extreme cold or heat (such as in direct sunlight, near a heater, or
in a car during the day) to prevent the possibility of panel
disfiguration or damage to the internal components.
• Do not use the instrument in the vicinity of a TV, radio, stereo
equipment, mobile phone, or other electric devices. Otherwise, the
instrument, TV, or radio may generate noise.
• Do not place the instrument in an unstable position where it might
accidentally fall over.
• Do not place vinyl, plastic or rubber objects on the instrument,
since this might discolor the panel or keyboard.
• Do not rest your weight on, or place heavy objects on the
instrument, and do not use excessive force on the buttons,
switches or connectors.
• Do not operate the instrument for a long period of time at a high or
uncomfortable volume level, since this can cause permanent
hearing loss. If you experience any hearing loss or ringing in the
ears, consult a physician.
• Before moving the instrument, remove all connected cables.
• Do not place the instrument against a wall (allow at least 3 cm/
one-inch from the wall), since this can cause inadequate air
circulation, and possibly result in the instrument overheating.
Using the bench (If included)
Connections
• Before connecting the instrument to other electronic components,
turn off the power for all components. Before turning the power on
or off for all components, set all volume levels to minimum. Also,
be sure to set the volumes of all components at their minimum
levels and gradually raise the volume controls while playing the
instrument to set the desired listening level.
Maintenance
• When cleaning the instrument, use a soft, dry cloth. Do not use
paint thinners, solvents, cleaning fluids, or chemical-impregnated
wiping cloths.
Handling caution
• Do not place the bench in an unstable position where it might
accidentally fall over.
• Do not play carelessly with or stand on the bench. Using it as a
tool or step-ladder or for any other purpose might result in
accident or injury.
• Only one person should sit on the bench at a time, in order to
prevent the possibility of accident or injury.
• If the bench screws become loose due to extensive long-term use,
tighten them periodically using the included tool.
Saving data
Saving and backing up your data
• All panel settings and Registration Memories are lost when you
turn off the power to the instrument. If you want to keep the
settings, save the data to a floppy disk (see page 67).
• Do not insert a finger or hand in any gaps on the instrument.
Backing up the floppy disk
• To protect against data loss through media damage, we
recommend that you save your important data onto two floppy
disks.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.
Always turn the power off when the instrument is not in use.
(1)B-7
2/2
3
Congratulations!
You are the proud owner of a fine electronic organ, Electone EL-100.
The Yamaha EL-100 Electone combines the most advanced AWM tone generation
technology with state-of-the-art digital electronics and features to give you stunning sound
quality with maximum musical enjoyment.
In order to make the most of the Electone and extensive performance potential, we urge you
to read the manual thoroughly while trying out the various features described.
Keep the manual in a safe place for later reference.
Included Items
Owner’s Manual
Music Stand
Dust Cover
Bench
Turning the Electone off erases all panel settings you have made. When the Electone is turned on, Basic
Registration 1 is automatically selected.
GM (General MIDI System Level 1) is an addition to the MIDI standard that ensures that any GM-compatible
music data can be accurately played by any GM-compatible tone generator, regardless of maker.
The GM mark is affixed to all software and hardware products that support the General MIDI standard.
XG is a new MIDI format created by Yamaha that significantly improves and expands upon the General MIDI
standard by providing a greater variety of high-quality voices plus considerably enhanced effect operation – while
being fully compatible with GM.
• The screen displays and illustrations as shown in this owner’s manual are for instructional purposes only, and may appear somewhat different
from those on your instrument.
• Copying of the commercially available music sequence data is strictly prohibited except for your personal use.
• The company names and product names in this Owner’s manual are the trademarks or registered trademarks of their respective companies.
• This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license
to use others’ copyrights. Such copyrighted materials include, without limitation, all computer software, styles files, MIDI files, WAVE data and
sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any
violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.
4
Table of Contents
Main Features ............................... 6
Panel Layout ................................. 7
EL-100 Panel Layout .......................................................... 8
5 Registration Memory .............. 67
1
2
3
4
Storing Registrations ......................................... 67
Selecting Registrations ...................................... 68
Saving the Registration Data to Disk .............. 68
Registration Shift ............................................... 69
1
Quick Introductory
Guide
2
Voice Sections
3
Voice Controls
and Effects
4
Rhythm and
Accompaniment
5
Registration Memory
6
Music Disk Recorder
(M.D.R.)
7
Footswitches and
Expression Pedal
8
Transpose and
Pitch Controls
9
MIDI
1 Quick Introductory Guide ........ 10
1
2
3
4
Getting Started ................................................... 10
Basic Registrations ............................................. 11
Basic Operation .................................................. 12
LCD DISPLAY ................................................... 13
2 Voice Sections ......................... 17
1
2
3
4
Voice Display ....................................................... 17
Selecting Voices from the Panel ........................ 18
Selecting Voices from the Dotted Buttons ....... 21
Voice Menus ........................................................ 23
3 Voice Controls and Effects ....... 29
1
Selecting from Voice Condition Pages ............. 30
(PAGE 1) .............................................................. 30
1 Initial Touch .................................................... 30
2 Feet .................................................................. 30
(PAGE 2) .............................................................. 31
1 Volume ............................................................. 31
2 Panning ............................................................ 31
3 Reverb .............................................................. 31
(PAGE 3) .............................................................. 32
1 Effect ............................................................... 32
(PAGE 4) .............................................................. 33
1 Vibrato ............................................................. 33
(PAGE 5) .............................................................. 34
2
1 Tune ................................................................. 34
2 Slide ................................................................. 34
Selecting from Effect Set Page ......................... 34
3
1 Tremolo/Chorus .............................................. 35
2 Symphonic/Celeste ......................................... 35
3 Delay ................................................................ 36
4 Flanger ............................................................. 38
5 Distortion ......................................................... 39
Selecting from the Panel .................................... 40
6 Music Disk Recorder (M.D.R.) .. 73
1
2
3
4
5
6
7
8
Precautions on M.D.R. ...................................... 73
Formatting a Disk .............................................. 75
Recording ............................................................ 76
Recording Registrations (and Bulk Data) ...... 82
Recalling Recorded Registrations
(and Bulk Data) .................................................. 83
Replacing Registrations .................................... 83
Playback .............................................................. 84
Other Functions .................................................. 88
7 Footswitches and
Expression Pedal .................... 97
1
2
Footswitch ........................................................... 97
Expression Pedal .............................................. 100
8 Transpose and Pitch Controls 101
9 MIDI ...................................... 102
10 Accessory Jacks and Controls .... 104
11 Appendix ............................. 105
MIDI .......................................................................... 105
MIDI Data Format .................................................. 111
MIDI Implementation Chart ................................. 120
Troubleshooting ....................................................... 122
EL-100 ASSEMBLY INSTRUCTIONS ................ 125
EL-100 Specifications .............................................. 129
Index .......................................................................... 131
1 Reverb .............................................................. 40
2 Sustain ............................................................. 41
3 Tremolo/Chorus .............................................. 42
4 Rhythm and Accompaniment .. 45
1
2
3
4
5
6
7
8
Selecting Rhythms from the Panel ................... 45
Rhythm Condition Pages .................................. 48
Dotted Buttons and User Rhythms .................. 49
Rhythm Menus ................................................... 51
Automatic Accompaniment Auto Bass Chord (A.B.C.) ................................ 52
Accompaniment Controls ................................. 54
Preset/User Keyboard Percussion .................... 56
Melody On Chord (M.O.C.) ............................. 64
10
11
Accessory Jacks
and Controls
Appendix
The Index on page 131 can be of your help in finding the functions and terms.
5
Main Features
1
Astoundingly True-to-life Sounds
The new AWM (Advanced Wave Memory) tone generation technologies combined with authentic touch
response make this Electone a truly expressive musical instrument.
You can enjoy playing a total of 173 AWM voices using the touch response function.
2
Wide Variety of High Quality Effects
Electone voices can also be enhanced with a full range of high-quality digital effects, ranging from Tremolo
and Reverb to Flanger, Delay and Distortion. Stereo panning is independent of effect on/off status. (page 34)
3
Dynamic Rhythm Patterns and Programmable Percussion Sounds
The Rhythm section of the Electone features authentic drum and percussion sounds, used by expert rhythm
programmers in creating a total of 66 rhythm patterns, ranging across all styles of music. (page 45)
The Keyboard Percussion function lets you play 120 different percussion sounds, each of which can be
assigned onto any key. (page 56)
4
Convenient Registration Functions
The Basic Registrations let you instantly change the voices for playing any styles of music. (page 11)
Also, Registration Memory Function lets you set up and record your own Electone settings, and call up them
in the middle of the performance. (page 67)
5
Versatile Functions of the Music Disk Recorder
The Electone also features a Music Disk Recorder (MDR) for recording your registrations and performances
to a floppy disk. In addition, the MDR allows you to copy a song from a disk to another, duplicate a disk, and
play commercially available XG song data. (page 73)
6
LCD for Systematic and Intuitive Operation
The systematic and intuitive LCD allows you to smoothly understand almost all the Electone operation.
6
Panel Layout
Music Stand
Upper Keyboard
Front Panel (pages 8-9)
Lower Keyboard
MIDI Jacks (page 104)
Jacks (page 104)
Right-Footswitch (page 69)
Speaker Unit
Left-Footswitch (page 97)
Expression Pedal (page 11)
Pedalboard
7
EL-100 Panel Layout
UPPER KEYBOARD VOICE
(page 17)
LEAD VOICE
(page 17)
PEDAL VOICE
(page 17)
LOWER KEYBOARD
VOICE
(page 17)
MAX
STRINGS
BRASS
CLARINET
SAXOPHONE
CHORUS
HARMONICA
ORGAN
PIANO
GUITAR
VIBRAPHONE
COSMIC
TUTTI
MIN
VIOLIN
FLUTE
OBOE
TRUMPET
MAX
TO
LOWER
MIN
SUSTAIN
MIN
PEDAL VOICE
LOWER KEYBOARD VOICE
UPPER
LOWER
MAX
PEDAL
STRINGS
BRASS
CLARINET
SAXOPHONE
CHORUS
HORN
ORGAN
PIANO
GUITAR
VIBRAPHONE
COSMIC
TUTTI
¨⁄String
Ò⁄String
BASIC
REGIST.
LEAD VOICE
UPPER KEYBOARD VOICE
REVERB
(page 40)
MAX
CONTRA
BASS
ELEC.
BASS
ORGAN
BASS
TUBA
MIN
MAX
TO
LOWER
MIN
RHYTHM
RHYTHM
(page 45)
SEQ.
1
SEQ.
2
MARCH
WALTZ
SWING
BOUNCE
SLOW
ROCK
SEQ.
3
SEQ.
4
TANGO
LATIN
1
LATIN
2
8 BEAT
16 BEAT
MAX
MIN
KEYBOARD
PERCUSSION
RHYTHM
BAR / BEAT
INTRO.
ENDING
LOWER
KEYBOARD
PERCUSSION
(page 56)
SYNCHRO
START
START
TEMPO
PEDAL
FILL IN
BAR / BEAT
TEMPO
(page 47)
8
LCD Display
(page 13)
DATA CONTROL
REVERB
SUSTAIN
(page 41)
DATA CONTROL
(page 14)
BAR/BEAT
(page 47)
BAR/BEAT/TEMPO
(page 47)
RHYTHM
(page 46)
BASIC REGIST.
(page 11)
DISPLAY SELECT (page 15)
A.B.C./M.O.C. Button (pages 52, 64)
EFFECT SET Button (page 34)
VOICE DISPLAY Button (page 20)
DISPLAY SELECT
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
PAGE
(page 14)
TREMOLO
(FAST)
TREMOLO (FAST) Button (page 44)
PITCH/MIDI Button (pages 101, 102)
REGIST. SHIFT Button (page 69)
FOOT SW. Button (page 97)
M./TO DISK
(page 67)
Registration Memory
(page 67)
D. (Disable)
(page 68)
MASTER VOLUME
DISPLAY SELECT
DATA CONTROL
PAGE
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
REGISTRATION MEMORY
s1ÎViolin1 ⁄
s1∏⁄ContBs.1
M.
/ TO DISK
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
1
2
3
4
5
6
7
8
MASTER VOLUME
(page 11)
D.
RECORD
UPPER
SONG
REPEAT
PAUSE
LOWER
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
STOP
PLAY
SHIFT
MUSIC DISK
RECORDER
(page 73)
SONG DEL.
FROM
TO
SONG COPY
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
POWER
POWER
(page 10)
Floppy Disk Slot
LED (Lamp in-use)
Eject
9
1 Quick Introductory Guide
1 Getting Started
1
Plug the power cord in to an appropriate electrical outlet.
2
Turn on the Electone by pressing the POWER switch.
Only use the voltage specified as correct
for the Electone. The required voltage is
printed on the name plate of the Electone.
Yamaha products are manufactured
specifically for the supply voltage in the
area where they are to be sold. If you
should move, or if any doubt exists about
the supply voltage, please consult with a
qualified technician.
POWER
When you turn on the Electone, the following displays will appear one
after the other on the LCD display:
YAMAHA
Electone
¨⁄Strings1ÎViolin1 ⁄
Ò⁄Strings1∏⁄ContBs.1
This last display, Voice Display, shows you the currently assigned
voice settings for each voice section.
When the Electone is turned on, Basic Registration 1 is automatically
selected.
10
3
Set the MASTER VOLUME control.
The MASTER VOLUME control is an overall control which affects the
volume of the entire instrument.
1
MASTER VOLUME
Quick Introductory Guide
4
Press the Expression pedal down with your foot.
Once you have set the MASTER VOLUME control to a suitable level,
you can use the Expression pedal to change the volume with your foot
as you play.
Louder
Softer
BASIC
REGIST.
2 Basic Registrations
“Registration” indicates a panel setting including upper keyboard voices,
lower keyboard voices, pedal voices, a rhythm and so on. The Basic
Registration section has five factory preset registrations, each with a
different set of voices for Upper/Lower keyboards and Pedalboard and
each specially suited for playing in a different music style.
To select Basic Registrations:
Press the BASIC REGIST. buttons to select each Basic Registration.
When you turn the power on, the Electone automatically selects Basic
Registration 1.
Basic
Basic
Basic
Basic
Basic
Registration 1 Registration 2 Registration 3 Registration 4 Registration 5
NOTE:
Upper Keyboard
Voice
Strings 1
Brass 1
Flute 1
Cosmic 1
Synth. Brass 1
Lower Keyboard
Voice
Strings 1
Horn1
Piano 1
Cosmic 2
Cosmic 3
Pedal Voice
Contra Bass1
Tuba
Contra Bass 1
Cosmic 2
Synth. Bass 1
Additional basic registrations are preset on
the Registration Memory locations from 1
to 8. See page 67 for the details.
Turning the Electone off erases all panel
settings you have made. When the
Electone is turned on, Basic Registration 1
is automatically selected.
11
3 Basic Operation
1
Quick Introductory Guide
Registration Set-up
Select the keyboard
to play
Select the voice
(Voice Menu)
Select the rhythm
(Rhythm Menu)
Finely adjust the voice
(Voice Condition)
Finely adjust the rhythm
(Rhythm Condition)
* The Controls and Effects may
be applied differently depending
on the selected type of Controls
and Effects. See page 29 for
more information.
Add effects
(Effect Set)
Add reverb
Adjust the total volume
(Master Volume)
Playing Electone
Setting Registration
Shift/Footswitch
Saving the
registration data
Recording the performance
Music Disk Recorder
Expression Pedal
Playing back
12
Loading the
registration data
4 LCD DISPLAY
1
Quick Introductory Guide
This section introduces you the convenient control functions of the LCD
display. The LCD display lets you see at a glance the current settings and
provides easy-to-understand graphic representation of all parameters.
Selecting a voice/rhythm
1
Press the panel voice/rhythm button which you want to use (For
example, press the STRINGS button in the Upper Keyboard Voice
section).
UPPER KEYBOARD VOICE
STRINGS
BRASS
CLARINET
SAXOPHONE
CHORUS
HARMONICA
ORGAN
PIANO
GUITAR
VIBRAPHONE
COSMIC
TUTTI
MAX
MIN
The following display will appear, showing all the available voices/
rhythms in the category (Strings Category in this case).
DATA CONTROL
DATA CONTROL
Strings1 Strings2
Pizz.Strs Syn.Strs1
2
Press the Data Control button corresponding to the voice you want to
play (Strings 2 in this case).
DATA CONTROL
DATA CONTROL
Strings1 Strings2
Pizz.Strs Syn.Strs1
The first letter of the selected voice/rhythm will start blinking.
For more information on the Voice Menu list see page 23.
13
Function of the Data Control Buttons
1
DATA CONTROL
DATA CONTROL
Quick Introductory Guide
Strings1 Strings2
Pizz.Strs Syn.Strs1
1
1
2
DATA CONTROL
DATA CONTROL
VOL.:24
PAN:C ¨1¤
REVERB:24
2
DATA CONTROL
DATA CONTROL
EFFECT:SYMPHONIC ¨1‹
”SYMPHONIC ’CELESTE
3
3
DATA CONTROL
DATA CONTROL
<R.SHIFT>[INS][DEL]¤
T_
??????????????????
Cursor
4
4
The Data Control buttons are used to select 1 a voice/rhythm or function
shown on the display. Each pair of buttons corresponding to the section of the
display directly above it increases/decreases 2 the value or chooses 3 a
setting/function. When you are setting the Registration Shift, each of them
moves the cursor 4 to the right/left.
Using Page Buttons
DATA CONTROL
pages
DATA CONTROL
¨⁄Strings1ÎViolin1 ⁄
Ò⁄Strings1∏⁄ContBs.1
These buttons 5 are used to select (when available) the various ‘pages’ of the
display, the names of which appear at the top right of the LCD. Use Page F to
select the next page, and Page E to select the previous page.
14
PAGE
5
Summary of the LCD Operation
1
The following chart gives you a general view of the basic operations on the Electone.
Quick Introductory Guide
1. To call up the LCD display
2) Pressing a Display Select button
1) Pressing Panel Buttons
● Selecting voices or setting up the Voice Condition
● Selecting rhythms or setting up the Rhythm
Condition
● Setting the Reverb effect
● Setting the Sustain
● Setting the User Keyboard Percussion
●
●
●
●
●
●
●
●
Displaying Voice Display (Manual Balance)
Setting effects
Setting A.B.C./M.O.C.
Setting the Left-Footswitch
Setting Registration Shift (Right-Footswitch)
Setting Pitch and Transpose
Setting MIDI
Selecting and setting Tremolo/Chorus
LCD display
2. To Select Pages
Selecting the page you want to
use with the Page buttons
3. To Actually Change the Settings
Using the Data Control buttons to:
● Select voices/rhythms/effects
● Turn on/off the Accompaniment and A.B.C. Memory
● Adjust Initial Touch and Reverb depth
● Move the pan position and cursor position
15
Language on the LCD
1
LCD display can be shown in two languages, English and Japanese.
Quick Introductory Guide
How to select the language:
1. Press the VOICE DISPLAY button in the DISPLAY SELECT section.
The page 1 will be displayed.
DISPLAY SELECT
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
DATA CONTROL
DATA CONTROL
¨⁄Strings1ÎViolin1 ⁄
Ò⁄Strings1∏⁄ContBs.1
2. Press the PAGE button to select the page 3.
DATA CONTROL
DATA CONTROL
<v(4∂/Display>
‹
’i-y∫
”English
3. Pressing each pair of Page buttons at the bottom select the language: the
right ones select English and the left ones select Japanese.
DATA CONTROL
DATA CONTROL
<v(4∂/Display>
‹
’i-y∫
”English
16
PAGE
2 Voice Sections
The EL-100 features 173 different high quality AWM voices. Each of the AWM voices can be used on the Upper
keyboard, Lower keyboard and Pedalboard. There are two voice sections for the Upper keyboard, one voice
section for the Lower keyboard and Pedalboard, respectively.
Each voice section can, of course, have its own Voice Condition page(s), which allow you to finely set up voice
and volume settings.
LEAD VOICE
UPPER KEYBOARD VOICE
BRASS
CLARINET
SAXOPHONE
CHORUS
HARMONICA
ORGAN
PIANO
GUITAR
VIBRAPHONE
COSMIC
TUTTI
MAX
VIOLIN
FLUTE
OBOE
TRUMPET
TO
LOWER
MIN
MIN
PEDAL VOICE
LOWER KEYBOARD VOICE
STRINGS
BRASS
CLARINET
SAXOPHONE
CHORUS
HORN
ORGAN
PIANO
GUITAR
VIBRAPHONE
COSMIC
TUTTI
2
MAX
Voice Sections
STRINGS
MAX
CONTRA
BASS
ELEC.
BASS
ORGAN
BASS
TUBA
MIN
MAX
TO
LOWER
MIN
1 Voice Display
You can visually confirm the voice assignments to each keyboard.
Pressing the VOICE DISPLAY button in the DISPLAY SELECT section selects
the Voice Display. (The Voice Display always appears when the Electone is
turned on.)
DISPLAY SELECT
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
The Voice Display is configured with three pages. Each page can be selected
using the Page buttons.
Page 1 and 2 show the currently assigned voice settings for each voice section,
as well as the overall balance between the Upper and Lower voices.
(page 1)
DATA CONTROL
UPPER KEYBOARD VOICE
LEAD VOICE
DATA CONTROL
PAGE
¨⁄Strings1ÎViolin1 ⁄
Ò⁄Strings1∏⁄ContBs.1
LOWER KEYBOARD VOICE
PEDAL VOICE
17
(page 2)
DATA CONTROL
UPPER KEYBOARD VOICE 2
Volume Balance
between UPPER
and LOWER (Page 20)
DATA CONTROL
PAGE
¨¤Strings1 M.BAL: 0¤
Ò¤Strings1∏¤ContBs.1
2
NOTE:
LOWER KEYBOARD VOICE 2
PEDAL VOICE 2
Voice Sections
In addition to the four panel voice groups such as Upper Keyboard Voice, Lower
Keyboard Voice, Pedal Voice and Lead Voice, the EL-100 has three “hidden”
voice groups, Upper Keyboard Voice 2, Lower Keyboard Voice 2, Pedal Voice 2.
These three voice groups are displayed on page 2 of the Voice Display screen.
This fact indicates the EL-100 owns the same voice group numbers as those of
the upper models like EL-500. Accordingly, the EL-100 can play back the
registrations created with the upper models like EL-500. You can change the
settings of each “hidden” voice group as you do with the panel voice groups.
See page 27 for the details.
For more information on the volume
balance between the Upper Keyboard and
the Lower Keyboard see page 20.
You can select the language shown on the LCD display on page 3 of the Voice
Display (page 16).
DATA CONTROL
DATA CONTROL
<v(4∂/Display>
‹
’i-y∫
”English
2 Selecting Voices from the Panel
Since selection of panel voices follows the same procedure throughout the
various sections, instructions for only the Upper Keyboard Voice are given
here.
1
Select a voice from the Upper Keyboard Voice section by pressing one
of the Voice buttons in that section.
UPPER KEYBOARD VOICE
STRINGS
BRASS
CLARINET
SAXOPHONE
CHORUS
HARMONICA
ORGAN
PIANO
GUITAR
VIBRAPHONE
COSMIC
TUTTI
MAX
MIN
If, for example, you have selected the ORGAN voice, the following
display (Voice Menu) will appear:
DATA CONTROL
DATA CONTROL
Organ1
JazzOrgan1
PopOrgan1 Accordion
18
Notice that several different voice names are shown on this display.
These are variations of the basic organ voice category.
PAGE
2
Press one of the Data Control buttons that corresponds to the voice you
wish to select. (Pop Organ 1, in this case)
DATA CONTROL
DATA CONTROL
Organ1
JazzOrgan1
PopOrgan1 Accordion
2
Voice Sections
The first letter of the selected voice will start blinking. You have
selected Pop Organ 1 for the Upper Keyboard Voice.
3
4
If you wish to, you can select voices from Lead Voice, Lower
Keyboard Voice and Pedal Voice sections, following steps #1 and #2
above.
Set the volume for each voice section.
There are two volume controls:
Coarse:
Use the VOLUME controls of each voice section on the panel to set the
desired level for each voice. The controls have seven volume settings,
from a minimum of 0, or no sound, to a maximum of full volume.
UPPER KEYBOARD VOICE
STRINGS
BRASS
CLARINET
SAXOPHONE
CHORUS
HARMONICA
ORGAN
PIANO
GUITAR
VIBRAPHONE
COSMIC
TUTTI
MAX
MIN
Fine:
Pressing the same panel voice button again (or the same Data Control
button corresponding to the selected voice) calls up the Voice
Condition display. Use the Page buttons to select page 2, which
contains Volume setting.
DATA CONTROL
DATA CONTROL
PAGE
INIT.T: 8
¨1⁄
FEET:PRESET
19
Use the top left side Data Control button pair to change the level of the
desired voice. Fine volume settings, 0-24, are available.
DATA CONTROL
DATA CONTROL
VOL.:24
2
PAN:C ¨1¤
REVERB:24
NOTE:
Pressing a voice button once calls up that
voice’s Voice Menu display. Pressing it a
second time calls up the Voice Condition
display. Successive presses alternate
between the two displays.
NOTE:
Voice Sections
The Lead and Pedal Voices sound one note
at a time; when you simultaneously press
two or more keys, only the highest note
will sound.
5
6
Now select voices for the Lower keyboard and Pedalboard as you did
for the Upper keyboard above. Also set the volumes of the voices.
Adjust the volume balance between the Upper and Lower Voices with
the Balance Control provided on the Voice Display.
To adjust the volume balance:
1. Press the VOICE DISPLAY button in the DISPLAY SELECT
section. The Voice Display always appears when the Electone is
turned on.
DISPLAY SELECT
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
2. Select page 2 of the Voice Display using Page buttons at the right
side of the LCD display.
DATA CONTROL
DATA CONTROL
PAGE
¨⁄Strings1ÎViolin1 ⁄
Ò⁄Strings1∏⁄ContBs.1
3. Adjust the balance with the corresponding Data Control buttons, at
the top right side. The positive values increase the Upper Keyboard
volume, while the negative values lower it, or increase the Lower
Keyboard volume. Range: -6 - +6
DATA CONTROL
DATA CONTROL
¨¤Strings1 M.BAL:+4¤
Ò¤Strings1∏¤ContBs.1
20
NOTE:
Pressing this pair of Data Control buttons
at the same time restores the balance to the
center position.
About TO LOWER - Playing (Upper) Lead Voice and Pedal Voice from the Lower keyboard:
The Electone has a special ‘To Lower’ function that lets you assign Lead or
Bass voices to the Lower keyboard. Simply press the TO LOWER button
on the voice section you wish to assign, and that voice will be playable
from the Lower keyboard.
PEDAL VOICE
LEAD VOICE
FLUTE
OBOE
TRUMPET
MAX
TO
LOWER
CONTRA
BASS
ELEC.
BASS
ORGAN
BASS
TUBA
MAX
2
Voice Sections
VIOLIN
When the TO LOWER button is turned on,
the Lead voices and Pedal voices cannot
be played on the Upper keyboard and
Pedalboard, respectively.
TO
LOWER
MIN
MIN
Turning the Electone off erases all panel settings you have made. When the Electone is turned on, Basic Registration 1 is automatically selected.
If you have made panel settings you wish to keep, save them to the floppy disk before turning the Electone off. See page 68 for more information.
3 Selecting Voices from the
Dotted Buttons
The EL-100 has a wide variety of voices from which you can choose – far
greater than what is immediately apparent from the front panel controls.
You’ve already learned in the section above how to select the different
voices that are available in the Voice Menu display of each panel voice.
The Electone also has dotted buttons in each voice section, giving you access to
even more voices. These dotted buttons function as ‘wild card’ Voice Menu
selectors; any internal voices can be selected from these buttons.
UPPER KEYBOARD VOICE
STRINGS
BRASS
CLARINET
SAXOPHONE
CHORUS
HARMONICA
ORGAN
PIANO
GUITAR
VIBRAPHONE
COSMIC
TUTTI
MAX
MIN
The dotted buttons have two basic uses:
● For playing any voice of the Voice Menus from any of the keyboards or
Pedalboard. You can play on the Upper keyboard, for example, voices
from the twenty-two Voice Menu pages (including User), and not be
limited to only the twelve buttons (equivalent to twelve Voice Menu
pages) that make up the Upper Voice section. Another advantage to this
feature is that when the normally monophonic (one note) Lead and
Pedal voices are assigned to the Upper or Lower keyboard Voice
sections, they can be played polyphonically.
● For having three different voices from the same Voice Menu page
available for selection in the same song. For example, you can
assign one of the voices to a dotted button in the Upper Keyboard
Voice section, the second voice to the other dotted button in the
same section, and the third one on the Voice Menu.
21
To select voices from the dotted buttons:
1
Press one of the dotted buttons in any of the voice sections.
Select Honky Tonk piano, for example, to the Dotted button 1 in Upper
Keyboard Voice.
2
UPPER KEYBOARD VOICE
Voice Sections
STRINGS
BRASS
CLARINET
SAXOPHONE
CHORUS
HARMONICA
ORGAN
PIANO
GUITAR
VIBRAPHONE
COSMIC
TUTTI
MAX
MIN
STRINGS, Voice Menu 1, appears.
DATA CONTROL
DATA CONTROL
<STRINGS>
01:Strings1
2
¨1‚⁄
Select one of the pages with the Page buttons, and choose a Voice
Menu. (PIANO, page 17, in this case)
DATA CONTROL
DATA CONTROL
<PIANO>
01:Piano1
PAGE
¨1⁄‡
NOTE:
3
Select 03: Honky Tonk piano voice using the Data Control buttons.
DATA CONTROL
DATA CONTROL
<PIANO>
03:Honky Tonk
¨1⁄‡
You have selected Honky Tonk for the Upper Keyboard Voice.
About User voices:
Page 22 is “User” area. Although EL-100 cannot exactly play back the user
voices created with the upper models like EL-900, the automatic conversion
function allows your EL-100 play back the voices fairly close to the original
sounds. However, some voices may not be reproduced properly.
DATA CONTROL
DATA CONTROL
<USER VOICE>
01:******
22
¨1¤¤
You can directly view and select Voice
Menu pages by holding down one of the
Dotted buttons and simultaneously
pressing the desired voice buttons in
succession.
4 Voice Menus
The following chart lists the voices that are shown by pressing the panel
voice buttons. The other voices that are only available when using the
Dotted buttons are shown on pages 24 - 26.
STRINGS Upper/Lower
CONTRABASS Pedal
Horn2
Huted Horn
Tuba
Timpani
Timp.Roll
Trumpet1 Trumpet2
Trombone1 Muted Trp
Flute1
Recorder
Piccolo
Whistle
CLARINET Upper/Lower
OBOE Lead
Oboe2
EnglshHorn
Clarinet1 Clarinet2
Bass Cla. Syn.Cla.1
TUTTI Upper/Lower
SAXOPHONE Upper/Lower
Saxophon1 Saxophon2
Sopra.Sax Syn.Lead1
Tutti1
Tutti3
Tutti2
Tutti4
HARMONICA Upper
CHORUS Upper/Lower
Chorus2
Vocal
Harmoni.1 Harmoni.2
ORGAN BASS Pedal
ORGAN Upper/Lower
Organ1
JazzOrgan1
PopOrgan1 Accordion
Org.Bass1 Org.Bass2
Org.Bass3 Org.Bass4
GUITAR Upper/Lower
PIANO Upper/Lower
E.Piano1
Harpsi.
Guitar1
Guitar2
ElecGtr.1 Harp
ELECTRIC BASS Pedal
VIBRAPHONE Upper/Lower
Vibrphone Glocken.
Marimba
Syn.Chime
ElecBass1 ElecBass2
Syn.Bass1 Syn.Bass2
USER VOICE Upper/Lower/Pedal
COSMIC Upper/Lower
Cosmic1
Cosmic3
Brass2
Syn.Brass1
FLUTE Lead
TUBA Pedal
Piano1
E.Piano2
Brass1
Brass3
TRUMPET Lead
HORN Lower
Chorus1
Chorus3
Violin2
PizzViolin
BRASS Upper/Lower
ContBass1 ContBass2
Pizz.Bass UprghtBass
Oboe1
Bassoon1
Violin1
Cello
Voice Sections
Strings1 Strings2
Pizz.Strs Syn.Strs1
Horn1
Horn3
2
VIOLIN Lead
Cosmic2
Cosmic4
<USER VOICE>
01:******
The details for each voice such as octave (feet) setting and effect on/off status are shown in the list on pages 24 - 26.
23
Details on All Voices
The voices not lead by a bullet indicate that they are only selectable using the Dotted buttons.
Preset
Page/Section
Voice Name
Comments
Effect
1. Upper/Lower
●
01: Strings 1
8'
-
Large strings ensemble.
STRINGS
●
02: Strings 2
8'
-
Relatively small strings ensemble for contemporary music.
2
●
Voice Sections
●
03: Strings 3
8'
-
Small strings ensemble.
04: Strings 4
8'
-
Having specific harmonics for layering other voices.
05: Strings 5
8'
-
For legato playing.
06: Strings 6
8'
-
Strings with clarity. Appropriate for the fast passages.
07: Strings 7
8'
-
Expressive full bodied strings with a slow attack.
08: Pizz. Strings
8'
-
Pizzicato strings.
09: Trem. Strings
8'
-
Tremolo strings.
10: Synth. Strings 1
8'
Cele.
Synth. strings with softer attack.
11: Synth. Strings 2
8'
Sym.
Bright synth. strings.
Softer Synth. strings.
12: Synth. Strings 3
8'
Cele
2. Lead
●
01: Violin 1
8'
-
For multi purposes.
VIOLIN
●
02: Violin 2
8'
-
For solo with sharp attack.
03: Violin 3
8'
-
Bright fidle for country music.
04: Violin 4
8'
-
Darker synth. violin with wider dynamic range.
05: Violin 5
8'
-
Violin with deep vibrato, also suited for chord playing.
●
06: Pizz. Violin
8'
-
Pizzicato violin.
●
07: Cello
8'
-
Cello with realistic rubbed string-instrument feel.
08: Kokyu
8'
-
Ancient Chinese fiddle.
8'
-
Standard type.
3. Pedal
●
01: Contrabass 1
CONTRABASS
●
02: Contrabass 2
8'
-
True-to-life tight contrabass sounding in an octave unison.
03: Contrabass 3
16'
-
Realistic contrabass solo.
●
04: Pizz. Bass
8'
-
Pizzicato contrabass for classicals.
●
05: Upright Bass
8'
-
For jazz.
4. Upper/Lower
●
01: Brass 1
8'
-
Trumpet and trombone ensemble for classicals.
BRASS
●
02: Brass 2
8'
-
For big band with brighter attack.
●
03: Brass 3
8'
-
With strong impact. Can be used as orchestra hit.
04: Brass 4
U16'/L8'
-
Trombone ensemble.
05: Brass 5
8'
-
Tight octave brass for contemporary music.
●
06: Synth. Brass 1
8'
-
Synth. brass with sharp attack. Used for Basic Regist. 5.
07: Synth. Brass 2
8'
-
Analog type. Can be used as melody line.
08: Synth. Brass 3
8'
-
Fat synth. brass.
5. Lower
●
01: Horn 1
8'
-
Standard horn for classicals.
HORN
●
02: Horn 2
8'
-
Horn unison solo. Alpenhorn.
●
03: Horn 3
8'
-
For solo playing.
04: Horn 4
8'
-
Impressive horn ensemble.
●
05: Muted Horn
8'
-
Muted horn.
6. Lead
●
01: Trumpet 1
8'
-
Standard trumpet for classicals.
TRUMPET
●
02: Trumpet 2
8'
-
Jazz trumpet 1 with full-bodied sounds.
03: Trumpet 3
8'
-
Sweet voice.
04: Trumpet 4
8'
-
Jazz trumpet 2 with a peculiar attack.
05: Trumpet 5
8'
-
Comical synth. trumpet.
06: Trumpet 6
8'
-
Resonant trumpet solo.
●
07: Muted Trp.
8'
-
Harmon mute.
●
08: Trombone 1
U16'/L8'
-
For legato playing.
09: Trombone 2
U16'/L8'
-
Bright trombone solo. For fast phrases.
10: Muted Trb.
U16'/L8'
-
Cup mute.
11: Flugel Horn
8'
-
Flugelhorn.
12: Euphonium
U16/L8
-
Euphonium with softer sounds.
7. Pedal
●
01: Tuba
16'
-
Accentuated by touch.
TUBA
●
02: Timpani
8'
-
Standard timpani.
●
03: Timpani Roll
8'
-
Typical timpani roll.
●
01: Flute 1
8'
-
Standard flute solo.
02: Flute 2
8'
-
For legato playing.
03: Piccolo
4'
-
Standard piccolo.
04: Yokobue
4'
-
Japanese pipe with clear sounds.
05: Recorder
4'
-
Block floete.
06: Ocarina
4'
-
Ocarina with simple but warm sounds.
07: Pan Flute
8'
-
Pan Flute.
8. Lead
FLUTE
●
●
●
24
Feet
08: Shakuhachi
8'
-
Japanese Shakuhachi with realistic breath noises.
09: Whistle
4'
-
Whistle.
Preset
Page/Section
Voice Name
Feet
Effect
Comments
9. Lead
●
01: Oboe 1
8'
-
Softer oboe.
OBOE
●
02: Oboe 2
8'
-
Rounder tone with characteristic tonguing. For fast phrases.
●
03: English Horn
8'
-
Cor Anglais.
●
04: Bassoon 1
U16'/L8'
-
For legato playing.
U16'/L8'
-
For staccato playing.
●
01: Clarinet 1
8'
-
Standard clarinet.
CLARINET
●
02: Clarinet 2
8'
-
Clarinet solo for jazz and contemporary.
●
03: Bass Cla.
8'
-
Bass clarinet with fat and resonant sounds.
●
04: Synth. Cla. 1
8'
-
Resonant synth. clarinet.
Synth. reed with a unique attack sound.
05: Synth. Cla. 2
8'
-
11. Upper/Lower
●
01: Saxophone 1
U16'/L8'
-
Alto sax.
SAXOPHONE
●
02: Saxophone 2
U16'/L8'
-
Characteristic tenor sax with strong tonguing.
●
03: Sopra. Sax.
8'
-
Standard soprano sax.
04: Sax. Ens. 1
U16'/L8'
-
Softer sounds for classicals.
05: Sax. Ens. 2
U16'/L8
-
Saxophone section for bigband.
06: Synth. Sax.
8'
-
Wind synthesizer with thick sounds in the middle and lower range.
07: Synth. Lead 1
8'
-
Softer analog synth. reed.
●
08: Synth. Lead 2
8'
-
Clear synth. reed with a sharp attack.
09: Synth. Lead 3
4'
-
Hoarse noise reed.
10: Synth. Lead 4
8'
-
Digital synth. reed.
11: Synth. Lead 5
8'
-
Synth. reed with thick fourth notes.
12. Upper/Lower
●
01: Tutti 1
8'
-
Strings unison and wood winds ensemble.
TUTTI
●
02: Tutti 2
8'
-
Strings unison and the brasses.
●
03: Tutti 3
8'
-
The brasses for classicals and bands.
●
04: Tutti 4
8'
-
Big band. Softer playing = sax only. Harder playing = 1 octave higher brasses added.
05: Tutti 5
8'
-
Wood winds ensemble. Instruments vary depending on the register played.
06: Tutti 6
8'
-
Wood winds quintet.
07: Tutti 7
8'
-
Brass ensemble.
Female “Ah”.
13. Upper/Lower
●
01: Chorus 1
8'
-
CHORUS
●
02: Chorus 2
8'
-
Male “Wh”.
●
03: Chorus 3
8'
-
Mixed chorus.
04: Chorus 4
8'
-
Mixed chorus with beautiful resonance. Wh.
05: Chorus 5
8'
-
Scat type vocal ensemble.
●
06: Vocal
8'
-
Accentuated solo vocal, “Ah”.
14. Upper
●
01: Harmonica 1
8'
-
Standard type with pitch modulated vibrato.
HARMONICA
●
02: Harmonica 2
8'
-
Solo harmonica with filter and amplitude modulated vibrato.
15. Upper/Lower
●
01: Organ 1
8'
-
Small pipe organ. 8'.
ORGAN
●
●
●
02: Organ 2
8'
-
Big pipe organ with full coupler.
03: Organ 3
8'
-
Nasard stops. 8'+2 2/3'.
04: Organ 4
8'
-
05: Jazz Organ 1
16'
Chor.
Harmonium.
For solo playing. 16'+8'+5 1/3'.
06: Jazz Organ 2
16'
Trem.
16'+8'+2'.
07: Jazz Organ 3
16'
Trem.
For cluster playing. 16'+1 3/5'+1 1/3'+1'.
08: Jazz Organ 4
16'
Chor.
Fat and noisy jazz organ.
09: Pop Organ 1
8'
Chor.
Bright sounds for jazz. 8'+4'+2 2/3'.
10: Pop Organ 2
8'
Chor.
For multi purposes.
11: Theat. Organ 1
8'
Sym.
8'+4' with slower attack.
12: Theat. Organ 2
8'
-
16'+8' with slower attack.
13: Accordion
8'
-
Slower attack.
14: Bandoneon
8'
-
Attack can be controlled by initial touch.
8'
-
Combination organ bass.
16. Pedal
●
01: Organ Bass 1
ORGAN BASS
●
02: Organ Bass 2
16'
-
Pipe organ bass 1. Standard type.
●
03: Organ Bass 3
16'
-
For jazz. 16'.
●
04: Organ Bass 4
16'
-
Pipe organ bass 2. Full coupler.
●
01: Piano 1
8'
-
For multi purposes.
02: Piano 2
8'
-
Brighter sounds. CP80 type.
17. Upper/Lower
PIANO
03: Honkytonk
8'
-
●
04: Elec. Piano 1
8'
Cele.
●
05: Elec. Piano 2
8'
Cele.
06: Elec. Piano 3
8'
-
●
2
Voice Sections
05: Bassoon 2
10. Upper/Lower
Honky tonk piano.
DX7 type.
Old fashioned, full bodied electric piano.
Electric piano with clearly brilliant but deep sounds.
07: Harpsichord
8'
-
Standard cembalo.
08: Clavi.
16'
-
Funky clavi.
09: Clavichord
8'
-
Clavichord with stable and grave sounds.
25
Preset
Page/Section
Voice Name
Feet
Comments
Effect
18. Upper/Lower
●
01: Guitar 1
U16'/L8'
-
Folk guitar. Steel string.
GUITAR
●
02: Guitar 2
U16'/L8'
-
Acoustic jazz guitar. Tone varies depending on the touch.
03: Guitar 3
U16'/L8'
-
Classic guitar. Suitable to backing for bossanova.
04: 12Str. Guitar
U16/L8
-
12-string classic guitar with gorgeous sounds.
2
Voice Sections
●
●
05: Banjo
8'
-
06: Mandolin
8'
Cele.
For country and dixieland.
07: Sitar
8'
-
08: Shamisen
8'
-
Japanese classical shamisen.
09: Elec. Guitar 1
U16'/L8'
-
For backing.
10: Elec. Guitar 2
U16'/L8'
-
For solo playing.
11: Muted Guitar
U16'/L8'
-
Muted guitar.
12: Dist. Guitar
U16'/L8'
-
Distorted guitar.
13: Harp
8'
-
Grand harp.
14: Steel Guitar
8'
-
Hawaiian guitar. Effective when used with the glide function.
15: Koto
8'
-
16: Taisho Koto
4'
Cele.
Standard mandolin.
Indian sitar with the different resonances between lower and mid./high ranges.
Japanese Koto.
Japanese Taisho Koto.
19. Upper/Lower
●
01: Vibraphone
8'
-
VIBRAPHONE
●
02: Glocken
4'
-
Glockenspiel.
03: Celesta
4'
-
Celesta.
●
●
Standard vibraphone.
04: Music Box
4'
-
Antique music box.
05: Marimba
8'
-
Concert marimba.
06: Xylophone
4'
-
Tone varies depending on the initial touch.
07: Chime
4'
-
08: Synth. Chime
8'
Cele.
Chime.
Starry chime.
09: Steel Drum
8'
-
20. Pedal
●
01: Elec. Bass 1
8'
-
Steel Drum.
For multi purposes.
ELECTRIC BASS
●
02: Elec. Bass 2
16'
-
Slap bass.
03: Elec. Bass 3
16'
-
04: Elec. Bass 4
16'
Cele.
Plucked bass with hard attack.
●
05: Synth. Bass 1
16'
-
Sustained sounds.
●
06: Synth. Bass 2
16'
-
With remarkable attack.
07: Synth. Bass 3
16'
-
Tone varies depending on the touch.
4'
-
Decay type. For multi purposes. UK in Basic Regist. 4.
Fretless bass, also suited for solo playing.
21. Upper/Lower
●
01: Cosmic 1
COSMIC
●
02: Cosmic 2
8'
-
The lower register of celesta. LK and PK in Basic Regist. 4.
●
03: Cosmic 3
8'
-
Brass type.LK in Basic Regist. 5.
●
04: Cosmic 4
8'
-
Decay type. With fantastic image.
05: Cosmic 5
8'
-
Spacious sounds with feedback.
06: Cosmic 6
8'
-
Synth. brass type.
07: Cosmic 7
8'
-
Vocal type with feedback.
08: Cosmic 8
8'
-
Distortion type with feedback.
09: Cosmic 9
8'
-
Decay type with unique feedback.
10: Cosmic 10
8'
-
Clear synth. pad.
11: Cosmic 11
8'
-
Digital synth. pad.
12: Cosmic 12
8'
-
Chorus type synth. pad.
13: Cosmic 13
8'
-
Special sound effect with a slower attack. The sounds drastically changes.
14: Cosmic 14
8'
-
Fantastic digital music box.
15: Cosmic 15
8'
-
Ethnic synth. percussion.
16: Cosmic 16
16'
-
Special sound effect with a complicated mixture of various sounds.
Some of the voices may be different from the ones on the upper models like EL-900 even if they have the same voice names.
26
To select the “hidden” voices
(Upper Keyboard Voice 2, Lower Keyboard Voice 2 and Pedal Voice 2):
You can call up the “hidden” voices on the LCD display and select them.
This function allows you to layer the voices on each keyboard to make the
sound thicker.
2
Voice Sections
The procedure is explained with the selection of Upper Keyboard Voice 2,
as an example.
1. Press one of the voice buttons in the Upper Keyboard Voice section
while holding down the VOICE DISPLAY button in the DISPLAY
SELECT section.
UPPER KEYBOARD VOICE
DISPLAY SELECT
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
STRINGS
BRASS
CLARINET
SAXOPHONE
CHORUS
HARMONICA
ORGAN
PIANO
GUITAR
VIBRAPHONE
COSMIC
TUTTI
MAX
MIN
If, for example, you have selected the ORGAN voice, the following
display (Voice Menu) will appear:
DATA CONTROL
DATA CONTROL
Organ1
JazzOrgan1
PopOrgan1 Accordion
Notice that several different voice names are shown on this display.
These are variations of the basic organ category.
NOTE:
In this case the lamp on/off status in the
Upper Keyboard Voice section will not be
affected since you are dealing with the
Upper Keyboard Voice 2.
2. Press one of the Data Control buttons that corresponds to the voice you
wish to select. (Pop Organ 1, in this case)
DATA CONTROL
DATA CONTROL
Organ1
JazzOrgan1
PopOrgan1 Accordion
The first letter of the selected voice will start blinking. You have
selected Pop Organ 1 for the Upper Keyboard Voice 2.
27
3. Set the volume for the Upper Keyboard Voice 2.
Pressing the same Data Control button corresponding to the selected
voice calls up the Voice Condition display. Use the Page buttons to
select page 2, which contains Volume setting.
DATA CONTROL
2
DATA CONTROL
PAGE
INIT.T: 8
Voice Sections
¨2⁄
FEET:PRESET
Use the top left side Data Control button pair to change the level of the
desired voice.
DATA CONTROL
DATA CONTROL
VOL.:24
PAN:C ¨2¤
REVERB:24
You can select the voices of Lower Keyboard Voice 2 and Pedal Voice
2 in the same manner.
NOTE:
Also, you can change the volume of the
Upper Keyboard Voice 2 voices by
pressing the Upper Keyboard Voice
volume buttons on the panel while
holding VOICE DISPLAY button.
NOTE:
The panel volume lamp position will not
be affected even if you change the
volume of Upper Keyboard Voice 2.
The volume buttons on the panel are
exclusive for the panel voice groups.
28
3 Voice Controls and Effects
The Electone is equipped with two general kinds of functions that can be used to change the sound of the voices:
Voice Controls and Effects.
Certain effects may have been applied to some of the voices, but can be modified as you like. All built-in effects
are digital.
The chart below shows the various voice controls and effects for the individual voice sections. Available
functions are indicated by circles. The controls and effects are differently applied depending on those types:
applied to each voice group, to each keyboard or to the entire system.
Inital
Touch
Feet
Volume
Pan
Reverb
*2
Tremolo Sym/Chorus phonic/ Delay Flanger Distortion Vibrato
*1
Celeste
Lead
Slide
Lead
Tune
3
Sustain
Voice Controls and Effects
Upper Keyboard Voice
Lower Keyboard Voice
Lead Voice
Pedal Voice
Voice Condition Page 1
Voice Condition Page 2
Voice Condition Page 3
Related Pages
Voice Condition Page 4
Voice Condition Page 5
(Lead Voice only)
Effect Set Page
Reverb Page
Sustain Page
Tremolo Page
*1
*2
Turning tremolo/chorus on/off and switching between tremolo and chorus are common to all voice sections.
The total reverb depth and length are controlled on the reverb page, though the different reverb settings can be done for each voice section.
To change the settings and add the effects, display the appropriate page:
1. Selecting from Voice Condition Pages
2. Selecting from Effect Set Pages
3. Selecting from the Panel
29
1 Selecting from Voice
Condition Pages
To call up the Voice Condition Pages:
Choose a voice on the panel, then press that voice’s panel button again. The
Voice Condition Choose a voice on page appears on the LCD display.
LEAD VOICE
3
Voice Controls and Effects
VIOLIN
FLUTE
OBOE
TRUMPET
MAX
TO
LOWER
MIN
Each voice group’s Voice Condition (except for Lead Voice) is configured with
four pages. Voice Condition of the Lead Voice consists of five pages.
Voice Condition [PAGE 1]
1
DATA CONTROL
DATA CONTROL
INIT.T: 8
Î ⁄
FEET:PRESET
2
The included items are different between Pedal Voice group and the others
(Only Feet setting is available with Pedal Voice group).
Pedalboard
∏1⁄
FEET:PRESET
1 Initial Touch
Controls volume and timbre according to the velocity at which you strike the
keys.
The harder you strike the keys, the greater the volume and the brighter the
timbre will become. All voices are provided with this expressive function,
making it possible to perfectly reproduce the subtle dynamic and tonal changes
of actual instruments.
Higher settings make the change wider.
Range: 0 - 14
2 Feet
Determines the octave setting of the voice group. You can use a certain voice in
the broader range.
PRESET is the original (factory) setting; 4' is the highest and 16' is the lowest.
2' setting is added to the Pedal Voice sections.
30
NOTE:
Minimum setting produces no effect at all.
Voice Condition [PAGE 2]
Press the Page buttons to select PAGE 2.
DATA CONTROL
1
VOL.: 0
2
DATA CONTROL
PAGE
PAN:C Î ¤
REVERB:24
3
1 Volume
3
Fine adjustment of the voice volume. See page 20 for more information.
Voice Controls and Effects
Range: 0 - 24
2 Panning
Determines the position of the voice in the stereo image.
Seven pan positions are available.
3 Reverb
Determines the amount of reverb applied to each Voice section. When the panel
REVERB control is set to the minimum, the setting here will have no effect.
See page 40 for the details.
Range: 0 - 24
31
Voice Condition [PAGE 3]
Press the Page buttons to select PAGE 3.
1
DATA CONTROL
EFFECT:PRESET
1-1
1-2
1-3
1-4
1-5
1-6
1-7
3
DATA CONTROL
PAGE
Î ‹
Voice Controls and Effects
PRESET
OFF
TREMOLO
SYMPHONIC
DELAY
FLANGER
DISTORTION
1 Effect
Determines the effect type applied to each voice section.
Each press of top left F Data Control button selects Preset, Off, Tremolo,
Symphonic, Delay, Flanger and Distortion, in order. Each press of top left E
Data Control button selects in the reversed order.
32
1 -1
Preset
Selects the original (factory) effect. When PRESET is selected, some
of the voices have already got a certain type of effects.
1 -2
Off
Cancels the effect.
1 -3
Tremolo
Selects Tremolo/ Chorus. See page 42 for the details of the Tremolo/
Chorus setting.
1 -4
Symphonic
Selects Symphonic/ Celeste. See page 35 for the details of the
Symphonic/ Celeste setting.
1 -5
Delay
Selects Delay. See page 36 for the details of the Delay setting.
1 -6
Flanger
Selects Flanger. See page 38 for the details of the Flanger setting.
1 -7
Distortion
Selects Distortion. See page 39 for the details of the Distortion setting.
NOTE:
Effect can also be selected in the Effect
Set page (page 34).
Voice Condition [PAGE 4]
Press the Page buttons to select PAGE 4.
1 -1
DATA CONTROL
DATA CONTROL
VIB:PRESET
Î ›
1 -3
DATA CONTROL
PAGE
DATA CONTROL
3
1 -2
Voice Controls and Effects
VIB:USER DEPTH: 0Î ›
DELAY: 0 SPEED: 0
1 -4
1 Vibrato
Vibrato function vibrates the voices to create softer image. Applied to each
voice group.
1 -1
PRESET/USER
Selects the original (factory) effect. When PRESET is selected, some
of the voices have already got vibrato effect.
Selecting User allows you to access the Vibrato parameters to create
your own vibrato setting.
NOTE:
The User vibrato may not be effective for
some voices such as Harmonica2, Electric
Piano1 and Synth. Chime.
NOTE:
1 -2
Delay
Determines the amount of time that elapses between the playing of a
key and the start of the vibrato effect (see diagram). Higher settings
increase the delay of the vibrato onset.
The Vibrato parameters, Delay, Depth and
Speed, are not displayed as long as Preset
is selected.
Range: 0 - 14
1 -3
Depth
Determines the intensity of the vibrato effect (see diagram). Higher
settings result in a more pronounced vibrato.
Range: 0 - 14
1 -4
Speed
Determines the speed of the vibrato effect (see diagram).
Range: 0 - 14
Vibrato Control
Speed
Delay
Depth
33
Voice Condition [PAGE 5]
Press the Page buttons to select PAGE 5.
1
DATA CONTROL
DATA CONTROL
TUNE: 0
SLIDE:OFF
Î fi
S.TIME: 0
2 -1
2 -2
1 Tune
3
Voice Controls and Effects
Determines the pitch of the Lead voice. This control lets you detune the Lead
voice relative to the other voices of the Electone, for producing a richer sound.
The higher the value set, the higher the pitch.
Range: 0-24 (max. 28.88 cents; 1 step= Ca.1.2cents)
2 Slide
Slide applies a portamento effect to notes played in legato. For example, if you
play one note, then play another before completely releasing the first note, the
pitch of the first note will ‘slide’ up or down to the second note. The Slide
function is effective within a one-octave range.
2 -1
On/Off
Determines on/off status of the Slide effect.
2 -2
Slide Time
Determines the speed of the slide or portamento effect. The higher the
value that is set, the slower the speed.
Range: 0 - 14
2 Selecting from Effect Set
Page
To call up the Effect Set page:
Pressing the EFFECT SET button in the DISPLAY SELECT section calls up the
Effect Set pages.
DISPLAY SELECT
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
See page 32 for the information on Preset and Off.
The explanation on each effect is given here.
34
PAGE
DATA CONTROL
DATA CONTROL
EFFECT:PRESET
1
2
3
4
5
PAGE
¨1
PRESET
OFF
TREMOLO
SYMPHONIC
DELAY
FLANGER
DISTORTION
3
Voice Controls and Effects
Selecting Voice Group
You can select the voice section to which the effect should be applied, by
pressing the Page buttons. The acronyms indicate each voice group.
¨1:
Ò1:
Î:
1:
Upper Keyboard Voice
Lower Keyboard Voice
Lead Voice
Pedalboard Voice
¨2:
Ò2:
2:
Upper Keyboard Voice 2
Lower Keyboard Voice 2
Pedalboard Voice 2
1 Tremolo/Chorus
See Tremolo section on page 42. Independently applied to each voice section.
2 Symphonic/Celeste
Determines the type of the Symphonic effect, SYMPHONIC (Sym.) or
CELESTE (Cele.).
Symphonic is a subtle echo effect that makes one voice sound like an ensemble.
For example, a solo violin voice played through Symphonic would sound like
many violins playing together.
SYMPHONIC simulates the effect of a large ensemble, while CELESTE creates
the effect of a gradually expanding sound.
Press the appropriate Data Control button to turn on the desired effect. The solid
(negative) box indicates the effect is turned on.
DATA CONTROL
DATA CONTROL
EFFECT:SYMPHONIC ¨1
”SYMPHONIC ’CELESTE
2 -1
2 -2
2 -1
Symphonic
Selects the Symphonic effect to the designated voice section.
2 -2
Celeste
Selects the Celeste effect to the designated voice section.
NOTE:
In the illustration at the left, Symphonic is
selected and effective.
35
3 Delay
Delay is a pronounced echo effect, with distinct delayed repeats of the original
sound. Independently applied to each voice section.
Delay Effect
Signal
Adjusts the level
balance using
BALANCE
parameter
Time
Delayed Signal
3
Adjusts the delay interval using TIME parameter
Voice Controls and Effects
Adjust the number of repeated sounds using FEEDBACK parameter
DATA CONTROL
DATA CONTROL
EFFECT:DELAY
¨1
ÚÆTIME----242mSec
3 -1
3-2
3-3
3-4
3-5
TIME
F.B.
BAL.
MODE
3 -1
Parameter Settings
The bottom left Data Control buttons select available Delay parameters.
Available parameters are as follows:
3 -2
Time
Determines the time between delayed repeats.
DATA CONTROL
DATA CONTROL
EFFECT:DELAY
¨1
ÚÆTIME----242mSec
Range: 5mSec – 956mSec
3 -3
Feedback
Determines the number of delayed repeats.
DATA CONTROL
DATA CONTROL
EFFECT:DELAY
ÚÆF.B.----28.5%
Range: 0.2% - 46.9%
36
¨1
3 -4
Balance
Determines the volume of the delay effect, relative to the original
sound. Higher settings produce a louder delay.
DATA CONTROL
DATA CONTROL
EFFECT:DELAY
ÚÆBAL.----60.6%
¨1
3
Range: 0% - 100%
Mode
Selects the delay type from Mono, ST (Stereo) 1, 2, 3.
Selecting one of the Stereo Delays produces more expanding image or
an image sounds move from right to left, or left to right.
DATA CONTROL
Voice Controls and Effects
3 -5
DATA CONTROL
EFFECT:DELAY
ÚÆMODE----MONO
¨1
Range: Mono, ST1, ST2, ST3
Characteristics of Each Delay Type
Monaural
Normal monaural delay.
ST1
Multi delay with complicated reflections. Provides the most pronounced
effect.
ST2
Simple stereo delay. Feedback is 0 and the first reflection only. Special
effects can be obtained.
ST3
Adds thickness and brilliance to the monaural delay.
37
4 Flanger
Flanger introduces a swirling, animated modulation effect to the sound.
Independently applied to each voice section.
Flanger Effect
Signal
Changes the pitch using
SPEED parameter
Sets the depth using
DEPTH parameter
Time
3
Intensifies the pitch change
using FEEDBACK parameter
Voice Controls and Effects
DATA CONTROL
DATA CONTROL
EFFECT:FLANGER
ÚÆSPEED--- 4.5Hz
4 -1
¨1
4-2 SPEED
4-3 F.B.
4-4 DEPTH
4 -1
Parameter Settings
The bottom left Data Control buttons select available Flanger
parameters. Available parameters are as follows:
4 -2
Speed
Determines the speed of the modulation.
DATA CONTROL
DATA CONTROL
EFFECT:FLANGER
ÚÆSPEED--- 4.5Hz
¨1
Range: 0Hz - 12.1Hz
4 -3
Feedback
Controls the brightness and the metallic sound of the effect.
DATA CONTROL
DATA CONTROL
EFFECT:FLANGER
ÚÆF.B.----35.2%
¨1
Range: 0.6% - 94.0%
4 -4
Depth
Determines the intensity of the effect.
DATA CONTROL
DATA CONTROL
EFFECT:FLANGER
ÚÆDEPTH---52.3%
Range: 37.8% - 87.8%
38
¨1
5 Distortion
Distortion adds a distorted image to the sounds usually found in electric guitars.
Independently applied to each voice section.
Distortion Effect
Determines the depth
using LEVEL parameter
Signal
Changes the
timbre using
HIPASS
parameter
DATA CONTROL
3
DATA CONTROL
Voice Controls and Effects
EFFECT:DISTORTION ¨1
ÚÆLEVEL---16.4dB
5 -1
5-2 LEVEL
5-3 HI PASS
5 -1
Parameter Settings
The bottom left Data Control buttons select available Distortion
parameters. Available parameters are as follows:
5 -2
Level
Determines the depth of the distorted sounds.
DATA CONTROL
DATA CONTROL
EFFECT:DISTORTION ¨1
ÚÆLEVEL---16.4dB
Range: 0dB – 21.8dB
5 -3
High Pass
Changes the timbre of the distorted sounds.
DATA CONTROL
DATA CONTROL
EFFECT:DISTORTION ¨1
ÚÆHI PASS- 476Hz
Range: 20Hz - 1036Hz
39
3 Selecting from the Panel
Reverb, Sustain and Tremolo/Chorus pages are called up by pressing the
respective panel buttons.
1 Reverb
Reverb adds an echo-like effect to the sound, giving the impression of a
performance in a large room or concert hall. Reverb effect can be applied to the
entire system or to each voice section (page 31) independently. Also, Reverb
can be applied to the rhythm and accompaniment independently.
3
Voice Controls and Effects
Press one of the REVERB buttons, located to the left of the panel, to set the
Reverb effect. The following display appears.
REVERB
MAX
MIN
REVERB page
1 -1
DATA CONTROL
<REVERB>
LENGTH:3
1 -2
DATA CONTROL
TYPE:HALL
DEPTH:16
1 -3
1 -1
Type
Determines the type of reverb effect: Room, Hall and Church. Each
type simulates a different acoustic environment; Room is the smallest
and Church the largest.
1 -2
Length
Determines the acoustic liveliness of the simulated room in the effect.
Higher settings make the room more reverberant.
Range: 0 - 6
1 -3
Depth
Fine adjustment of the depth of reverberation or the level of the
reflected sounds. Coarse reverb depth settings are made with the panel
REVERB buttons.
Range: 0 - 24
40
NOTE:
When this parameter or the panel
REVERB control is set to the minimum,
the settings in each voice condition page
(page 31) have no effect.
2 Sustain
The Sustain effect, selectable for the Upper, Lower and Pedal voices, causes
voices to gradually fade out when the keys are released. The sustain on/off and
sustain length settings are independent for each keyboard, providing maximum
expressive control.
Press one of the SUSTAIN buttons, located to the left of the panel, to set the
Sustain effect. The following display appears.
The lamp of the button lights up to indicate that sustain is on. Press the button
again to turn sustain off.
3
SUSTAIN
LOWER
Voice Controls and Effects
UPPER
PEDAL
SUSTAIN Page
DATA CONTROL
DATA CONTROL
<SUSTAIN> UPPER:10
LOWER:10 PEDAL: 6
Upper/Lower/Pedal
Determines the length of sustain applied to each keyboard. The display shows
the current sustain length values for each keyboard. The values here must be set
high enough for the sustain effect to be noticeable.
NOTE:
Sustain cannot be applied to the Lead
voices.
Range: 0 - 12
NOTE:
Remember that the SUSTAIN buttons are
on/off switches. If you use them to simply
check the sustain length values, you may
unintentionally change the on/off status of
the effect. Remember to check whether the
sustain button lamps are on or off before
you start to play.
41
3 Tremolo/Chorus
Tremolo recreates the rich, swirling sound of the popular rotating speaker effect.
Just as with a conventional rotating speaker, you can switch between slow and
fast speeds. And like a motor-driven speaker, the characteristic tremolo effect
gradually changes speed after it is switched. You can also adjust the maximum
speed of the effect to suit your playing style. The Tremolo effect can be
switched in real time as you play with either the front panel button or the Left
Footswitch (when properly set for Footswitch operation).
3
■ Tremolo Operation
Voice Controls and Effects
For Panel Voices (Voice Menu)
1
Select (turn on) Tremolo effect in each Voice Condition
page 3.
2
Adjust the Tremolo setting in Tremolo
Control (or Effect Set) page.
3
Assign footswitch for Tremolo Control, if desired.
Turn on Tremolo as you play,
with Tremolo button or Footswitch.
42
1) Turning on the Tremolo effect (set to standby):
You cannot use the Tremolo effect only by turning on the TREMOLO (FAST)
button. First, you need to turn the effect on in the desired voice section(s).
Independently applied to each voice section.
Select (turn on) Tremolo
1
Press the desired voice button on the panel twice to display one of the
Voice Condition pages.
3
LEAD VOICE
FLUTE
OBOE
TRUMPET
MAX
Voice Controls and Effects
VIOLIN
TO
LOWER
MIN
The Voice Condition page appears.
2
Select page 3 of the Voice Display using PAGE buttons at the right side
of the LCD display.
DATA CONTROL
DATA CONTROL
EFFECT:PRESET
3
PAGE
Î ‹
Select Tremolo to turn it on.
DATA CONTROL
DATA CONTROL
EFFECT:TREMOLO
Î ‹
43
2) Setting the Tremolo Effect
Tremolo setting made here are global; in other words, they are applied the same
to all voices for which Tremolo has been turned on (set to standby).
To turn on the Tremolo effect and call up the Tremolo Control page:
Press the TREMOLO (FAST) button in the DISPLAY SELECT section.
The following display appears.
DISPLAY SELECT
3
Voice Controls and Effects
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
DATA CONTROL
DATA CONTROL
<TREMOLO> <CHORUS>
SPEED:6.82 MODE:SLOW
1
2
The lamp of the button lights up to indicate that Tremolo is on. Press the button
again to turn Tremolo off and Chorus on (the LED turns off).
1 Tremolo Speed
Determines the speed of the Tremolo (rapid rotation) effect.
Range: 4.75Hz – 7.77Hz
2 Chorus Mode
Determines the effect applied when Tremolo is switched off: a slow chorus
effect (SLOW) or STOP. Use the SLOW setting when you want to have a
constant rotating speaker sound.
3) Realtime control of Tremolo effect
Once the Tremolo effect has been turned on and set, you can control the effect
in real time from the panel or from the Left Footswitch (page 97). Simply press
the TREMOLO (FAST) button in the DISPLAY SELECT section to turn the
Tremolo effects on and off while you’re playing. This button functions just like
the fast/slow switch on an actual rotating speaker cabinet. When Tremolo is on,
the rotation effect is fast; when off (Chorus), it is slow. The speed change is
gradual, effectively simulating the slowing down and speeding up of a rotating
speaker. You can also use the Left Footswitch to control the Tremolo effect in
the same way, if the Footswitch has been properly assigned.
44
4 Rhythm and Accompaniment
The Rhythm features of the Electone use actual drum and percussion sampled sounds to automatically play
various rhythms. Automatic Accompaniment functions are used with the rhythms, providing appropriate and
completely automatic accompaniment to match the style of the selected rhythm. Moreover, the Electone has a
Keyboard Percussion feature that allows you to play drum and percussion sounds from the Lower keyboard
and Pedalboard.
1 Selecting Rhythms from the Panel
Ten different rhythm categories in various styles can be instantly selected
from the front panel. The Electone has many more ‘hidden’ rhythms,
however. A total of 66 rhythms are available, and can be selected by using
the display.
4
1) To select and play a rhythm:
Rhythm and Accompaniment
1
Press any of the RHYTHM buttons once.
NOTE:
RHYTHM
SEQ.
1
SEQ.
2
MARCH
WALTZ
SWING
BOUNCE
SLOW
ROCK
SEQ.
3
SEQ.
4
TANGO
LATIN
1
LATIN
2
8 BEAT
16 BEAT
In addition to 10 different rhythm styles,
four types of metronome sounds, simple
metronome, two four, three four and four
four, are assigned to the SEQ 1 – 4
buttons, respectively, as the defaults.
MAX
MIN
Designated Rhythm Menu page will be displayed.
DATA CONTROL
DATA CONTROL
8Beat1
8Beat2
DancePop1 DancePop2
The first letter of the currently selected rhythm will start blinking.
2
Press the Data Control button corresponding to the rhythm you wish to
play, as you do with the voices.
The first letter of the selected rhythm will start blinking. Dance Pop 1
is selected here, for example.
DATA CONTROL
DATA CONTROL
8Beat1
8Beat2
DancePop1 DancePop2
NOTE:
The chord/bass patterns matching with the
designated rhythm will be selected
automatically when the A.B.C. function is
turned on. (Refer to the Auto Bass Chord
section, page 52, for details on Auto Bass
Chord and Memory.)
45
3
Turn the rhythm on.
You can use one of three buttons to turn on the rhythm:
RHYTHM
INTRO.
ENDING
SYNCHRO
START
START
3
2
1
FILL IN
1 START
This button does as its name indicates; the rhythm begins as soon as
the button is pressed. To stop the rhythm, press this button again.
2 SYNCHRO START
This button puts the rhythm in ‘stand-by’ status. The rhythm will
start when you press a note on the Lower keyboard or Pedalboard.
4
Rhythm and Accompaniment
3 INTRO. ENDING
Pressing this button automatically adds a short introduction (of up to
eight measures) before starting the actual rhythm.
First, press the INTRO. ENDING button, then the START or
SYNCHRO START button to actually start the rhythm.
While the introduction is playing, the display shows the countdown
to the first measure of the pattern. For example, if there is an eightmeasure lead-in for a pattern in 4/4 time, the following display
appears.
Pressing the INTRO. ENDING button again while the pattern is
being played will automatically add an ending phrase before
stopping the rhythm.
BAR / BEAT
NOTE:
The Left Footswitch can also be used to
turn the rhythm on and off in the middle of
song. To assign the Footswitch for rhythm
control, see page 98.
NOTE:
ABOUT SYNCHRO START:
Synchro Start functions quite differently
when the Auto Bass Chord feature is
turned on and the Accompaniment
Memory is turned off. The rhythm starts
when a key on the Lower keyboard is
played, but then immediately stops when
the key is released. To keep this from
happening, turn the Memory function on.
(Refer to the Auto Bass Chord section,
page 52, for details on Auto Bass Chord
and Memory.)
LEAD IN
Pressing the START button while holding down the INTRO. ENDING
button automatically plays a special one-measure Lead In, with a click on
each beat, to cue you in to the beginning of the song.
4
Set the volume using the panel rhythm volume button.
The controls have seven volume settings, from a minimum of 0, or no
sound, to a maximum of full volume. Fine adjustments in the volume of
the rhythm can also be made from the Rhythm Condition page (page 48).
RHYTHM
SEQ.
1
SEQ.
2
MARCH
WALTZ
SWING
BOUNCE
SLOW
ROCK
SEQ.
3
SEQ.
4
TANGO
LATIN
1
LATIN
2
8 BEAT
16 BEAT
MAX
MIN
46
NOTE:
When the Electone is turned on, the
Rhythm Volume is automatically set to 0.
5
Set the rhythm tempo using the Tempo button in the rhythm section.
BAR / BEAT
2
(TEMPO Display:
shows current tempo)
TEMPO
1
BAR / BEAT
1 TEMPO Button
For adjusting the speed of the rhythm. Pressing the right button
increases the tempo and pressing the left button decreases it.
Range: 40 - 240
When the rhythm begins playing, the TEMPO display changes
function to a Bar/Beat indicator.
4
Rhythm and Accompaniment
2 TEMPO Display (BAR/BEAT Indicator)
Shows the current tempo. (Displayed values are given in beats per
minute, just as on a conventional metronome.)
NOTE:
When you press the TEMPO Button even
while the rhythm is playing, the display
momentarily changes to show the current
tempo.
BAR / BEAT
The number on the left indicates the current bar
or measure and the one on the right indicates
the number of the beat in each bar.
The beat indicator lamp below the TEMPO
buttons also indicates the beats.
(BAR/BEAT Indicator: shows the
current position in the measures)
2) To use the Fill In patterns:
Fill In patterns are designed to be used as temporary and regular rhythmic
breaks to spice up a repeating rhythm. Like the regular rhythms, all Fill In
patterns have been designed to perfectly match the bass and chord parts of the
Automatic Accompaniment feature.
1
2
Select and play a rhythm.
As you play the Electone along with the rhythm, occasionally press the
FILL IN button.
RHYTHM
INTRO.
ENDING
SYNCHRO
START
START
FILL IN
NOTE:
USING A FILL IN FOR THE START
OF A SONG:
Fill In patterns can also be used as
introductions; simply press the FILL IN
button before starting the rhythm with the
START or SYNCHRO START buttons.
NOTE:
PLAYING PARTIAL FILL IN
PATTERNS:
You can also start Fill In patterns within a
bar, in order to play only the final one or
two beats of the Fill In pattern and create
additional rhythmic interest. Since the Fill
In feature is very sensitive to bar/beat
boundaries, you should be very careful to
‘play’ the FILL IN button precisely on (or
just slightly before) the beat that you want
the Fill In pattern to begin.
47
2 Rhythm Condition Pages
The Rhythm Condition includes the following two pages: the Rhythm
Condition page used to adjust the rhythms and the Instrument page used to
make up each drum/percussion instrument, each of which comprises the
rhythms and is playable using the Keyboard Percussion function.
To select the Rhythm Condition page:
Choose a rhythm, and press that pattern’s panel button again (or again press the
Data Control button corresponding to the selected rhythm). (The button should
be pressed only once if the Rhythm display has already been called up;
otherwise press the button twice.)
RHYTHM
4
Rhythm and Accompaniment
SEQ.
1
SEQ.
2
MARCH
WALTZ
SWING
BOUNCE
SLOW
ROCK
SEQ.
3
SEQ.
4
TANGO
LATIN
1
LATIN
2
8 BEAT
16 BEAT
MAX
MIN
Rhythm Condition [PAGE 1]
1
DATA CONTROL
VOL.: 0
REV.:12
3
2
DATA CONTROL
BAL.: 0 ⁄
’AUTO VARI.
4
1 Volume
Fine Adjustment of rhythm/keyboard percussion volume.
Range: 0 - 24
2 BAL. (Balance)
Determines the balance between two main sound types of the rhythms: the
drum sounds and the cymbal sounds. Positive settings emphasize the cymbal
sounds, while negative settings emphasize the drums.
Range: -6 - 0 - +6
NOTE:
Pressing this pair of Data Control buttons
at the same time restores the balance to the
center position.
3 Reverb
Determines the amount of reverb applied to the rhythms and percussion
sounds used in the rhythms. When the panel REVERB control is set to the
minimum, the setting here will have no effect.
Range: 0 - 24
4 Auto Variation
On/off switches of the Auto Variation function. Use the bottom right Data
Control button to turn on the Auto Variation function (Solid box indicates
the function is effective). The Auto Variation function lets you set pattern
variations to be played automatically. When set to ON, Auto Variation
automatically substitutes additional pattern variations to make the rhythm
more interesting and complex.
48
NOTE:
The Auto Variation function is not applied
to some of the rhythms.
Rhythm Condition [PAGE 2]
DATA CONTROL
DATA CONTROL
ACC.VOL.: 0 ”ON’OFF¤
ACC.REV.:24 TYPE:1
The settings related to Accompaniment are available on this page. See page 54
for the details.
3 Dotted Buttons and User
Rhythms
4
Rhythm and Accompaniment
The Rhythm section also has, like the voice sections, dotted buttons from
which rhythms can be selected. These dotted buttons function as ‘wild
card’ rhythm selectors; any of the rhythms available from the panel
buttons, the Rhythm Menus or User rhythms loaded from optional Pattern
Disk can be selected from these buttons.
1) To select a rhythm from a dotted button:
1
Press one of the dotted buttons on the right side of the Rhythm section.
RHYTHM
SEQ.
1
SEQ.
2
MARCH
WALTZ
SWING
BOUNCE
SLOW
ROCK
SEQ.
3
SEQ.
4
TANGO
LATIN
1
LATIN
2
8 BEAT
16 BEAT
MAX
MIN
MARCH, Rhythm Menu 1, appears.
DATA CONTROL
DATA CONTROL
<MARCH>
01:March1
2
‚⁄
Select one of the pages with the Page buttons, and choose a Rhythm
Menu.
DATA CONTROL
DATA CONTROL
<SWING>
01:Swing1
PAGE
‚‹
49
3
Select the desired rhythm using the Data Control buttons.
DATA CONTROL
DATA CONTROL
<SWING>
07:JazzBallad
‚‹
2) To call up the User rhythms:
You can call up the rhythms created by the other Electone that has Rhythm
Pattern Programming function and those on optional Pattern Disks.
4
Rhythm and Accompaniment
1
Press Page buttons to select the User page.
DATA CONTROL
DATA CONTROL
<USER RHYTHM>
01:USER1-A
2
⁄⁄
Press to select the User rhythm number and its Type.
DATA CONTROL
DATA CONTROL
<USER RHYTHM>
04:USER1-D
50
⁄⁄
PAGE
4 Rhythm Menus
NOTE:
The Baroque on the March page is
configured with accompaniment only; it
does not contain any drum or percussion.
This chart lists all 66 of the rhythms available on the Electone.
MARCH
WALTZ
March1
Country1
Polka1
Broadway
Waltz1
J.Waltz1
SWING
Waltz2
Bolero
BOUNCE
Swing1
J.Ballad
Swing2
Dixieland1
Bounce1
Reggae1
SLOW ROCK
Bounce2
Reggae2
TANGO
SlowRock1 SlowRock2
SlowRock3
Tango1
Tango3
Tango2
4
LATAN2
LATIN1
Rhumba
Mambo
Samba1
Bossa.1
Samba2
Bossa.2
Rhythm and Accompaniment
ChaCha
Beguine
16 BEAT
8 BEAT
16Beat1
Funk1
8Beat1
8Beat2
DancePop1 DancePop2
16Beat2
Funk2
USER RHYTHM
<USER RHYTHM>
01:USER1-A
The rhythms not lead by a bullet can be selectable only through the Dotted buttons.
Page
Category
LCD
Page
Category
LCD
Page
Category
01
MARCH
● 01:March1
05
SLOW ROCK
●
●
●
●
●
●
●
●
●
●
11
USER RHYTHM
02:March2
03:March3
● 04:Polka1
06
TANGO
05:Polka2
● 06:Country1
07:Country2
07
LATIN1
● 08:Broadway
09:Baroque
02
WALTZ
● 01:Waltz1
● 02:Waltz2
SWING
02:USER1-B
03:SlowRock3
03:USER1-C
01:Tango1
04:USER1-D
02:Tango2
05:USER2-A
03:Tango3
06:USER2-B
01:ChaCha
07:USER2-C
02:Rhumba
08:USER2-D
03:Beguine
09:USER3-A
04:Mambo
10:USER3-B
05:Salsa
11:USER3-C
12:USER3-D
05:Waltz5
03:Samba3
14:USER4-B
● 06:JazzWaltz1
15:USER4-C
07:JazzWaltz2
● 04:Bossanova1
● 05:Bossanova2
08:JazzWaltz3
06:Bossanova3
17:USER5-A
● 09:Bolero
● 01:Swing1
● 02:Swing2
LATIN2
13:USER4-A
16:USER4-D
● 01:8Beat1
● 02:8Beat2
18:USER5-B
03:8Beat3
20:USER5-D
03:Swing3
04:8Beat4
21:USER6-A
04:Swing4
05:8Beat5
22:USER6-B
05:Swing5
● 06:DancePop1
● 07:DancePop2
23:USER6-C
08:DancePop3
25:USER7-A
09:DancePop4
26:USER7-B
09
8 BEAT
● 07:JazzBallad
● 08:Dixieland1
19:USER5-C
24:USER6-D
● 01:16Beat1
● 02:16Beat2
27:USER7-C
03:16Beat3
29:USER8-A
03:Bounce3
04:16Beat4
30:USER8-B
● 04:Reggae1
● 05:Reggae2
05:16Beat5
31:USER8-C
09:Dixieland2
BOUNCE
01:USER1-A
02:SlowRock2
04:Waltz4
08
06:Swing6
04
LCD
● 01:Samba1
● 02:Samba2
03:Waltz3
03
01:SlowRock1
● 01:Bounce1
● 02:Bounce2
10
16 BEAT
● 06:Funk1
● 07:Funk2
28:USER7-D
32:USER8-D
08:Funk3
51
5 Automatic Accompaniment Auto Bass Chord (A.B.C.)
The Auto Bass Chord (A.B.C.) function works with the Rhythm section of the
Electone to automatically produce chord and bass accompaniment as you play.
There are three modes to obtain Automatic Accompaniment patterns.
To select the A.B.C. function:
Press the A.B.C./M.O.C. button in the DISPLAY SELECT section.
DISPLAY SELECT
4
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
Rhythm and Accompaniment
The following display appears.
A.B.C. [PAGE 1]
1
DATA CONTROL
<ABC>
OFF
1-1
1-2
1-3
1-4
OFF
SINGLE
FINGERED
CUSTOM
2
DATA CONTROL
<MEMORY> ⁄
’L ’P 2
-2
2 -1
1 A.B.C. Type
You can select one of three automatic accompaniment functions here.
Each press of bottom left F Data Control button selects Off, Single
Finger, Fingered Chord and Custom A.B.C., in order. Each press of bottom
left E Data Control button selects in the reversed order.
52
1 -1
Off
Cancels the Auto Bass Chord function.
1 -2
Single Finger
Provides the fastest and easiest means to obtain many different
chord/bass combinations, by simply using one, or at most, two or
three fingers to play the chords.
1 -3
Fingered Chord
Automatically produces bass and chord accompaniment for chords
played in the Lower keyboard. It allows you to use a wider range of
chord types than in the Single Finger mode. In the Fingered Chord
mode, you play all the notes of the chord while the Auto Bass Chord
function automatically selects the appropriate bass pattern.
1 -4
Custom A.B.C.
A slight variation on the Fingered Chord mode. It allows you to
determine what bass notes will be played in the accompaniment by
playing a note on the Pedalboard along with the chords you play in
the Lower keyboard.
2 Memory
When you start a rhythm with this memory function on, A.B.C. automatic
accompaniment keeps playing even after you release your fingers from the
Lower keyboard.
Lower
Use the bottom right E Data Control button to turn on the Lower
keyboard Memory function (Solid box indicates the function is
effective). Selecting this keeps the chord accompaniment of the
Lower Keyboard voices playing even after you release your fingers
from the Lower keyboard.
2 -2
PEDAL
Use the bottom right F Data Control button to turns on the
Pedalboard Memory function (Solid box indicates the function is
effective). Selecting this keeps the chord accompaniment of the
Pedalboard voices playing even after you release your fingers from
the Lower keyboard.
4
Rhythm and Accompaniment
2 -1
2) Chords Recognized in the Single Finger Mode
Major, minor, 7th and minor 7th chords can all be played in the Single Finger
mode.
G
F
A
G
B
A
D
B
C
With Single Finger, the chord produced
will sound in the same octave regardless of
where it is played on the Lower keyboard.
E
D
NOTE:
E
NOTE:
(Key of C)
C
Major chords:
Press the root of the chord (the note that corresponds to the
chord’s name).
Cm
Minor chords:
Simultaneously press the root and any one black key to the left
of it.
PLAYING SINGLE FINGER CHORDS
WITHOUT RHYTHM:
Auto Bass Chord is generally used with
rhythms to create full rhythmic accompaniment, but it can also be used in the
Single Finger mode to add full continuous
chords to your performance without the
use of the rhythm. Simply leave the
rhythm off in Single Finger mode, and
play Single Finger chords from the Lower
keyboard.
C7
7th chords:
Simultaneously press the root and any one white key to the left
of it.
Cm7
Minor 7th chords:
Simultaneously press the root as well as any black key and any
white key to the left of it.
NOTE:
If you forget to cancel the Single Finger or
Fingered Chord accompaniment functions,
single notes that you play will be sounded
as continuous chords.
NOTE:
Minor, 7th and minor 7th chords with
black key roots (such as B or G) are
played in the same way as those with
white key roots.
53
3) Chords Recognized in the Fingered Chord Mode
(Key of C)
C
Cm
C7
Cm7
Cmaj7
Cm maj7
C+5
C7+5
Cdim
C7sus4
Cm7-5
C-5
C7-5
C6
Cm6
4
Rhythm and Accompaniment
6 Accompaniment Controls
The Accompaniment function described in this section is independent of the
A.B.C. accompaniment. When rhythms are used, A.B.C. provides
rhythmical chords and bass, while the Accompaniment of this section
provides arpeggiated chords and other instrumental embellishments.
This control is selected from the Rhythm Menu and Rhythm Condition
pages.
1
Press any of the RHYTHM buttons twice.
RHYTHM
SEQ.
1
SEQ.
2
MARCH
WALTZ
SWING
BOUNCE
SLOW
ROCK
SEQ.
3
SEQ.
4
TANGO
LATIN
1
LATIN
2
8 BEAT
16 BEAT
MAX
MIN
Rhythm Condition page 1 appears.
DATA CONTROL
DATA CONTROL
VOL.: 0
REV.:12
54
BAL.: 0 ⁄
’AUTO VARI.
2
Press the Page buttons to select PAGE 2.
DATA CONTROL
DATA CONTROL
PAGE
ACC.VOL.: 0 ”ON’OFF¤
ACC.REV.:24 TYPE:1
Rhythm Condition [PAGE 2]
1
DATA CONTROL
2
DATA CONTROL
ACC.VOL.: 0 ”ON’OFF¤
ACC.REV.:24 TYPE:1
4
4
Rhythm and Accompaniment
3
1 ACCOMPANIMENT
Determines the volume of the Accompaniment.
Range: 0 - 24
2 On/Off
On/off switches of the Accompaniment function. Use the top right
Data Control buttons to turn on/off the Accompaniment function.
3 ACC. Reverb
Determines the amount of reverb applied to the Accompaniment.
When the panel REVERB control is set to the minimum, the setting
here will have no effect.
Range: 0 - 24
4 Type
Four types of accompaniment are available.
These settings provide various types of rhythmic and melodic
accompaniment, and generally become more complex according to
the type number.
3
Start the rhythm by pressing START button and play the Lower
keyboard.
An appropriate accompaniment pattern, suited to the current rhythm
and the chord played on the Lower keyboard, will be played
automatically.
NOTE:
Even if the Accompaniment Type is
changed, the Intro/Ending and Fill In
patterns remain the same.
NOTE:
When the Electone is turned on, the
Accompaniment Volume is automatically
set to 0 (factory setting). Be sure to set the
Accompaniment Volume to the appropriate value when using the Accompaniment
function.
55
7 Preset/User Keyboard
Percussion
The keyboard Percussion function features a total of 120 different drum
and percussion sounds, playable from the keyboards and pedalboard.
The Keyboard Percussion has two different modes, Preset and User. Preset
Keyboard Percussion lets you play 43 different sounds from the Lower
keyboard and Pedalboard, while the User Keyboard Percussion lets you
freely assign the 120 available sounds to any key or pedal you wish.
1) To use the Preset Keyboard Percussion:
1
2
4
Turn off the Lower and/or Pedal voices by setting each voice’s volume
to MIN.
Rhythm and Accompaniment
Turn on the Keyboard Percussion function by pressing the LOWER/1
and/or PEDAL/2 buttons in the KEYBOARD PERCUSSION section
on the left side of the panel.
KEYBOARD
PERCUSSION
LOWER
PEDAL
DATA CONTROL
DATA CONTROL
<KBP1>
”LK PRESET ’USER1
3
Set the volume.
The volume of the percussion sounds is set together with that of the
rhythm volume.
RHYTHM
SEQ.
1
SEQ.
2
MARCH
WALTZ
SWING
BOUNCE
SLOW
ROCK
SEQ.
3
SEQ.
4
TANGO
LATIN
1
LATIN
2
8 BEAT
16 BEAT
MAX
MIN
4
56
Play some notes on the Lower keyboard and/or Pedalboard. The 43
percussion sounds have been assigned to the keyboards as shown in the
chart below.
NOTE:
Pressing the KEYBOARD PERCUSSION
button call up the Menu display. You can
select from Preset (LK/PK preset) or User
(one of the eight Users you created). LK
Preset/PK Preset is selected as the
defaults. If not, select the Preset.
Preset Keyboard Percussion
Preset Percussion Assignments for the Lower Keyboard (43)
O
rc
le
O
l
d
ve
s
3
2
1
ol
l
1
3
2
1
m
ol
se
p
la
C
d
an gh
H Hi
o
og ow
L
Ag
o
og
h
Ag
ig
H
k
oc w
o
Bl
L
d
oo lock
W
B
1
d
ll
be
ow en
p
C
ng
la
m
m
m
R
ot
m
m
m
ru
R
lo
D
m
C
ru
le
D
ng
ia
oo
W
Tr
ia
e
C
To
To
To
h
Sh
To
To
To
e
h.
h.
h.
us
h
ar
nt
nt
nt
Br
us
Sn
ar
Tr
Sn
ra
e
Br
ar
e
st
ar
he
Sn
Sn
Sy
Sy
Sy
4
Rhythm and Accompaniment
er
ak igh
Sh a H
c
ui Low
C
ca igh
ui
C oH
ng ow
Bo o L h
ng ig
Bo ga H
w
on o h
C a L Hig
g
on 1
C ale Low
b 1
m
Ti le
ba
m t
Ti ane e al 2
t in b
as r
C bou Cym al 1
m ra mb
Ta est Cy
h
rc ra l 1
O st ba
he m
rc y 1
O h C al
b
s
ra m
C Cy n
e pe
id
R at O ed 1
s
i-h lo im
H tC R t
a m h 1
i-h ru ig
H e D L erb
m
ar ru ev
Sn e D R vy
ar rum ea
Sn e D m H avy
ar ru He
Sn re D m t
a ru gh
Sn e D Li vy
ar um ea
Sn Dr H um
ss um Dr
Ba Dr ss
ss Ba
Ba ert
c
on
C
NOTE:
Preset Percussion Assignments for the Pedalboard (18)
h.
nt
Sy
h.
nt
Sy
h.
nt
Sy
m
To
m
To
m
To
m
To
m
To
m
To
1
2
n
pe
O
y
av
He
rb
ve
Re
t
gh
Li
m
Ri
ed
os
Cl
um
Dr
um
Dr
um
Dr
y
av
He
um
Dr
um
Dr
1
l1
ba
m
Cy
ra
st
he
l1
rc
O
ba
m
Cy
h
as
l1
Cr
ba
m
Cy
at
-h
Hi
3
de
Ri
1
e
ar
Sn
at
-h
Hi
2
e
ar
Sn
ss
Ba
e
ar
Sn
e
ar
Sn
3
ll
Ro
1
ot
Sh
h
us
Br
h
us
Br
e
ar
Sn
e
ar
Sn
You can rearrange the key assignments of
the drum and percussion sounds using the
following User Keyboard Percussion
function.
1
57
2) To use the User Keyboard Percussion:
A total of 120 different drum and percussion sounds can be assigned to any key
or pedal, and your original setups can be saved to eight memory locations: User
1 through User 8. (For this example, use User1)
1
Turn on the Keyboard Percussion function by pressing the LOWER/1
button in the KEYBOARD PERCUSSION section.
KEYBOARD
PERCUSSION
LOWER
<KBP1>
”LK PRESET ’USER1
PEDAL
4
Rhythm and Accompaniment
The Menu display appears on the LCD, and indicates that the LK
(Lower Keyboard) PRESET is currently selected.
The Menu can be selected from LK PRESET and eight Users, USER 1
through USER 8.
When the PEDAL/2 button is used to call up the Menu display:
KEYBOARD
PERCUSSION
LOWER
<KBP2>
”PK PRESET ’USER1
PEDAL
The Menu can be selected from PK (Pedalboard) PRESET and eight
Users, USER 1 through USER 8.
2
Select User 1 using the bottom right Data Control buttons. This means
that you change the function of the Keyboard Percussion button from
Preset to User. You have selected User 1 for the LOWER/1 button.
When you select one of the Users, a Page number will be added to the
top right side of the display.
DATA CONTROL
DATA CONTROL
<KBP1>
[COPY]
’LK PRESET ”USER1
58
⁄
NOTE:
User 1 and User 2 contain the LK Preset
data and PK Preset data, respectively, as
the defaults.
3
Press the Page buttons to select PAGE 2.
The page 2 allows you to assign the instruments to each key/
pedalboard.
DATA CONTROL
1
3
DATA CONTROL
‚⁄CYMBAL
[SET] ¤
01:Crash Cym1[CLEAR]
2
4
1 Group
Lets you select the percussion group you want using the top left
Data Control buttons. The percussion groups are 12, 01 – 12. (Refer
to the User Keyboard Percussion Categories list below.)
4
Rhythm and Accompaniment
2 Instrument Names
The individual instruments are shown in the display and can be
selected with the appropriate Data Control buttons. (Refer to the
User Keyboard Percussion Categories list below.)
3 Set
Assigns the selected instrument to the key you wish. (See the
following explanation in the step #4.)
4 Clear
This function is used to erase User assignment for User 1.
CLEAR works in two ways: either to erase a single instrument, or to
erase all instruments. (See step #5 below.)
NOTE:
Playing back EL-100’s MDR reproduces
the instrument condition set by EL-900/
700/500.
59
User Keyboard Percussion Categories
Category
LCD
Category
LCD
01 CYMBAL
01:Crash Cym1
08 CUICA/SURDO
01:Cuica High
02:Crash Cym2
02:Cuica Med.
03:CrashCym M
03:Cuica Low
04:Ride Cym1
04:Tamborim O
05:Ride Cym2
05:Tamborim M
06:RideCymCup
06:Surdo Open
07:Orch.Cym1
07:Surdo Mute
08:Orch.Cym2
08:Surdo Rim
09:Orch.Cym M
10:Cym March
02 HI-HAT
4
Rhythm and Accompaniment
03 SNARE DRUM
09:Surdo Muff
09 TIMBALE/COW
11:Cym BrShot
02:Timbale1 L
12:Tam-Tam
03:Timbale2 H
01:HH Open
04:Timbale2 L
02:HH Close
05:Timbale3 H
03:HH Pedal1
06:Timbale3 L
04:HH Pedal2
07:Timbale4 H
05:AnalogHH O
08:Timbale 4 L
06:AnalogHH C
09:Cowbell1
01:SD Light
10:Cowbell2
02:SD Heavy
11:Cowbell3
03:SD Rim1
04:SD Rim2
04 SNARE BRUSH
12:Cowbell4
10 PERCUSSION1
06 BASS DRUM
02:Shaker
06:SD Accent2
03:Maracas H
07:SD Reverb1
04:Maracas L
08:SD Reverb2
05:GuiroShort
09:Synth.SD
06:Guiro Long
10:Orch.SD
07:Wood High
11:SD Roll
08:Wood Med.
12:Analog SD
09:Wood Low
01:SD BrShot1
10:Claves
02:SD BrShot2
11:Castanet
01:Tom1
12:Vibraslap
11 PERCUSSION2
02:Agogo Low
03:Tom3
03:Triangle O
04:Tom4
04:Triangle C
05:TomBrShot1
05:Windbell1
06:TomBrShot2
06:Windbell2
07:TomBrShot3
07:Tambourine
08:TomBrShot4
08:Pandeiro
09:Synth.Tom1
09:Bell
10:Synth.Tom2
10:Hand Claps
11:Synth.Tom3
11:Fingersnap
01:BD Light
12:Scratch
03:BD Attack
13:Noise Per.
12 PERCUSSION3
01:Kotsuzumi1
04:Synth.BD
02:Kotsuzumi2
05:BD March
03:Kotsuzumi3
06:Concert BD
04:Kotsuzumi4
07:Analog BD1
05:Ohtsuzumi1
08:Analog BD2
06:Ohtsuzumi2
01:Conga High
07:Taiko1
02:Conga Low
08:Taiko2
03:Conga Slap
09:Ohdaiko1
04:Conga Muff
10:Ohdaiko2
05:CongaSlide
11:Kakegoe1
06:Bongo High
12:Kakegoe2
07:Bongo Low
13:Kakegoe3
08:Bongo Slap
09:Bongo Mute
60
01:Agogo High
02:Tom2
02:BD Heavy
07 CONGA/BONGO
01:Cabasa
05:SD Accent1
03:SD BrRoll
05 TOM
01:Timbale1 H
4
To assign an instrument to a particular key or pedal:
Simultaneously hold down the Data Control button corresponding to
[Set] and press the key (or pedal) to which the instrument is to be
assigned. The currently displayed instrument will be assigned to the
key you press down as a part of User 1.
Upper Keyboard
DATA CONTROL
‚flBASS DRUM
02:BD Heavy
[SET] ¤
[CLEAR]
Lower Keyboard
or
Pedalboard
Continue the operation above to build up your own User Keyboard
Percussion set.
If you want, you can erase the instrument assignment.
Rhythm and Accompaniment
5
4
To erase one instrument:
Simultaneously hold down the Data Control button corresponding to
CLEAR and press the key (or pedal) corresponding to the instrument
you wish to erase.
(A short ‘beep’ sound indicates that the instrument has been erased.)
To erase all instruments:
1. Press, then release the Data Control button corresponding to
CLEAR. The following display appears, prompting confirmation of
the operation.
DATA CONTROL
DATA CONTROL
≥ Assign All Clear?≥
≥ [CLEAR] [CANCEL]≥
2. Press any of the bottom left Data Control buttons (corresponding to
[Clear] in the display) to erase all data. When [Clear] is selected, a
‘Completed’ message momentarily appears on the display.
Press any of the bottom right Data Control buttons (corresponding
to [Cancel] in the display) to abort the operation.
NOTE:
Though eight User Keyboard Percussion
setups can be created, they cannot be
memorized to Registration Memory. Only
on/off data and the Keyboard Percussion
Menu are memorized to Registration
Memory.
NOTE:
Two User Keyboard Percussions currently
selected by LOWER/1 and PEDAL/2 are
playable if both buttons are on.
61
3) Other User Keyboard Percussion Functions
Additional operations in the User mode include copying of Lower/Pedal Preset
Keyboard Percussion to one of the Users, and copying from one User location to
another.
To copy the Lower Preset Keyboard Percussion to one
of the Users:
The following operation allows you to copy the Lower Preset Keyboard
Percussion to one of the Users. The copy operation is convenient for
creating a slight modification from the Preset.
1. Turn on the Keyboard Percussion function by pressing the LOWER/
1 button in the KEYBOARD PERCUSSION section.
4
2. Select the User number to which you want to copy using the bottom
right Data Control buttons.
Rhythm and Accompaniment
DATA CONTROL
DATA CONTROL
<KBP1>
[COPY]
’LK PRESET ”USER1
⁄
3. Press the top right Data Control buttons to select Copy function.
DATA CONTROL
DATA CONTROL
<KBP1>
[COPY]
’LK PRESET ”USER1
⁄
The following display appears:
DATA CONTROL
DATA CONTROL
≥ ÚÆPRESET Copy?
≥
≥ [COPY]
[CANCEL]≥
4. Press top left Data Control buttons to select the copy source (in this
case, Lower Preset Keyboard Percussion).
DATA CONTROL
DATA CONTROL
≥ ÚÆPRESET Copy?
≥
≥ [COPY]
[CANCEL]≥
62
5. Press any of the bottom left Data Control buttons (corresponding to
[Copy] in the display) to copy the data. When [Copy] is selected, a
‘Completed’ message momentarily appears on the display.
Press any of the bottom right Data Control buttons (corresponding
to [Cancel] in the display) to abort the operation.
DATA CONTROL
DATA CONTROL
≥
≥
PRESET Copy
Completed!!
≥
≥
The Pedal Preset Keyboard Percussion (PK PRESET) can be copied
in the same way.
DATA CONTROL
4
DATA CONTROL
Rhythm and Accompaniment
<KBP2>
”PK PRESET ’USER1
To copy from one User location to another:
1. Turn on the Keyboard Percussion function by pressing the LOWER/
1 (or PEDAL/2) button in the KEYBOARD PERCUSSION section.
2. Select the User number to which you want to copy using the bottom
right Data Control buttons.
DATA CONTROL
DATA CONTROL
<KBP1>
[COPY]
’LK PRESET ”USER3
⁄
3. Press the top right Data Control buttons to select Copy function.
DATA CONTROL
DATA CONTROL
<KBP1>
[COPY]
’LK PRESET ”USER3
⁄
The following display appears:
DATA CONTROL
DATA CONTROL
≥ ÚÆUSER1 Copy?
≥
≥ [COPY]
[CANCEL]≥
63
4. Select the User number from which you want to copy using the top
left Data Control buttons.
DATA CONTROL
DATA CONTROL
≥ ÚÆUSER1 Copy?
≥
≥ [COPY]
[CANCEL]≥
In this case, the destination User number will not be displayed as
the source number, or selectable on the display.
5. Press any of the bottom left Data Control buttons (corresponding to
[Copy] in the display) to copy the data. When [Copy] is selected, a
‘Completed’ message momentarily appears on the display.
Press any of the bottom right Data Control buttons (corresponding
to [Cancel] in the display) to abort the operation.
4
Rhythm and Accompaniment
DATA CONTROL
DATA CONTROL
≥
≥
USER1 Copy
Completed!!
≥
≥
8 Melody On Chord (M.O.C.)
The Melody On Chord (M.O.C.) feature automatically adds a harmony
part to the melodies you play on the Upper keyboard. The harmony is
derived from the chords you play on the Lower keyboard – or from the
chords that are played for you, if you use Automatic Accompaniment.
Melody On Chord has three different modes, each providing a different set
of harmonies to accompany the melody played.
To display the M.O.C. function, press A.B.C./M.O.C. button in the DISPLAY
SELECT and then select the Page 2.
DISPLAY SELECT
64
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
M.O.C. [PAGE 2]
DATA CONTROL
DATA CONTROL
<MOC>
MODE:OFF
1
2
3
4
5
¤
OFF
1
2
3
1 Mode
You can select one of three automatic accompaniment functions here.
Each press of bottom left F Data Control button selects Off, 1, 2 and 3, in
order. Each press of bottom left E Data Control button selects in the
reversed order.
4
Rhythm and Accompaniment
2 Off
Cancels the Melody On Chord function.
3 1
Produces harmonies of up to two notes in a range close to the melody
played.
4 2
Produces harmonies of up to three notes in a range close to the melody
played.
5 3
Produces harmonies of up to four notes in a range relatively distant from the
melody played.
NOTE:
Melody On Chord applies only when the
Upper keyboard voice section’s volume is
set to the appropriate value.
65
About the Rhythm Sequence
Rhythm Sequence is built up with various different rhythm patterns, and
can be programmed by the other Electone such as EL-900.
The EL-100 doesn’t have Rhythm Sequence function, but it can read and
load the rhythm sequence data recorded on the MDR (a floppy disk) to its
four SEQ buttons in the Rhythm section and play back them, as follows:
1. Insert the floppy disk containing rhythm sequence data into the EL-100’
s MDR slot. The rhythm sequence data is recorded as a part of
registration data (explained on page 78).
2. Select the song number containing the registration data and press PLAY
button on the MDR to load the data. The rhythm sequence data has been
loaded to the Electone, or SEQ button(s).
4
Rhythm and Accompaniment
3. Press the desired SEQ button. The SEQ button’s lamp will be lit.
NOTE:
RHYTHM
SEQ.
1
SEQ.
2
MARCH
WALTZ
SWING
BOUNCE
SLOW
ROCK
SEQ.
3
SEQ.
4
TANGO
LATIN
1
LATIN
2
8 BEAT
16 BEAT
MAX
You can have up to all four rhythm
sequences play back automatically by
pressing the SEQ buttons.
MIN
4. Turn the START button on and play the rhythm sequence(s).
NOTE:
RHYTHM
INTRO.
ENDING
SYNCHRO
START
START
FILL IN
Four types of metronome sounds,
simple metronome, two four, three four
and four four, are assigned to the SEQ 1
– 4 buttons, respectively, as the
defaults.
NOTE:
During the rhythm sequence playback, the rhythm name currently
played back is displayed on the LCD.
66
As soon as you load the sequence data
using MDR, the default settings on each
SEQ button, four types of metronome
sounds, will be overwritten, or lost.
Turning the power off resets the
Electone to the defaults.
Also, pressing any of the BASIC
REGIST. buttons generates a short beep
sound and retrieves the metronome
sounds.
5 Registration Memory
Registration Memory allows you to store virtually all the settings you make on the panel and LCD, providing a
convenient way to instantly change all voice settings and rhythms while you’re playing, with the simple touch of
a single button on the Registration Memory panel.
REGISTRATION MEMORY
M.
/ TO DISK
1
2
3
4
5
6
7
8
D.
Functions and settings that cannot be memorized are:
● Reverb type
● Pan, Reverb, Tune and Volume settings for the
instruments (Drum and percussion sounds)
● User Keyboard Percussion settings (except for User
numbers currently assigned to the Lower/Pedal buttons)
● Registration Shift settings
● Pitch/Transpose settings
● User rhythm patterns in a Pattern Disk (except for
User rhythm numbers currently assigned to the
Dotted buttons)
● Rhythm Sequence
● MIDI settings
When turned on, various types of basic registrations are preset on the
numbered buttons from 1 through 8.
No. Name
1
Marching Band
5
Latin
2
Polka
6
2 Beat
3
8 Beat Ballad
7
Organ Ballad
4
Strings Waltz
8
Dance Pop
When you record your registration setting to one of the numbered buttons, the
preset registration on that button will be overwritten and erased as a result.
When you turn off the Electone, your own
registration setting(s) will be reset to the
default, or erased. Turning the Electone
back to on restores the preset registration
settings (the defaults).
If you want to keep your own registration
settings, you need to record them onto a
floppy disk before turning the Electone
off. Refer to page 68 for details on saving
registration data to disk.
Registration Memory
No. Name
5
NOTE:
1 Storing Registrations
Newly created registrations you make can be stored to the Registration
Memory panel buttons. All registrations in Registration Memory can also
be saved to floppy disk for future recall.
1
2
After creating your original registration, decide which numbered button
you wish to store.
Be careful when turning off the power,
since it erases all your existing data.
Always save your important data to a
floppy disk using M.D.R. (page 68) in
advance.
While holding down the M (Memory) button in the Registration
Memory section, press the numbered button to which you wish to save
your registration.
REGISTRATION MEMORY
M.
/ TO DISK
1
1. While holding down M button..
2
3
4
5
6
7
8
D.
2. ...Press desired numbered button.
When the registration is stored, the lamp above the numbered button
flashes momentarily.
NOTE:
Although the number of the Registration
Memory buttons of EL-100 are limited to
eight, from Registration Memory 1
through Registration Memory 8, the
Registration Memory 9 through Registration Memory 16 can be accessible when
using MDR playback and Registration
Shift functions.
67
2 Selecting Registrations
NOTE:
Simply press the numbered button that corresponds to the registration you
wish to select.
Although the number of registration memory
locations is limited to eight, from 1 through
8, the registrations assigned in the memory
locations from 9 through 16 of an upper
model are accessible using the following
method. To select the number between the
registration memory 9 and 16, press one of
the eight registration memory buttons while
holding down the VOICE DISPLAY button
in the DISPLAY SELECT section (in this
case, the buttons 1 through 8 correspond to
the buttons 9 through 16, respectively). Any
of the numbered button lamps is not lit while
the registration between 9 and 16 is selected.
Using the D (Disable) button:
Rhythm and automatic accompaniment patterns also change when you
select different Registration Memory buttons. Pressing the D (Disable)
button allows you to keep the same rhythm and accompaniment patterns
throughout all your registration changes, or make your own rhythm
selections if you want to.
5
REGISTRATION MEMORY
NOTE:
The settings, can be disabled, are:
■ Current rhythm pattern
■ Rhythm Condition
■ Tempo
■ A.B.C./M.O.C. settings
M.
/ TO DISK
1
2
3
4
5
6
7
8
D.
Registration Memory
3 Saving the Registration Data
to Disk
1
Insert a formatted disk into the disk slot under the Music Disk Recorder
(M.D.R.). Make certain that the disk is either blank or has data you can
erase. If the disk is new and unformatted, you will have to format it.
Refer to the instructions how to format a disk (page 75).
2
Select a song number on the M.D.R. using the SONG SELECT buttons.
You can also select a song number shown on the display using the
appropriate Data Control button and (if necessary) using Page buttons
to display the appropriate page. A song name is displayed next to the
song number that already contains data.
RECORD
UPPER
LOWER
NOTE:
See pages 82 and 83 for the details on
saving/recalling registrations to/from the
M.D.R.
NOTE:
Song name may not be displayed
depending on the Electone model created
the data.
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SHIFT
<SONG NAME>
01:
SONG
REPEAT
PAUSE
FROM
TO
SONG COPY
STOP
PLAY
SONG DEL.
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
There are 40 songs (ten song numbers on the four pages), or memory
locations, available on a single disk.
68
⁄
3
While holding down the RECORD button on the M.D.R., press the M
(Memory) button in Registration Memory.
RECORD
UPPER
LOWER
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
TO
FROM
SONG COPY
SONG
REPEAT
PAUSE
STOP
SHIFT
SONG DEL.
PLAY
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
REGISTRATION MEMORY
M.
/ TO DISK
1
2
3
4
5
6
7
8
D.
This operation saves all eight registrations in Registration Memory to one song.
The other 39 available songs on the disk can be used for saving additional
batches of 8 registrations.
5
Registration Memory
4 Registration Shift
The Registration Shift function allows you to change registrations, all the
settings you make on the panel and LCD, without taking your hands from
the keyboards. Using the Right Footswitch on the Expression Pedal, you
can “jump” to a specified registration or step through the panel
registrations in sequence, either in numeric order or in any order you
specify.
Press the REGIST. SHIFT button in the DISPLAY SELECT section. REGIST.
SHIFT page will be displayed.
DISPLAY SELECT
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
REGIST SHIFT Page
Select one of the modes using the bottom left Data Control buttons.
Registration Shift has three modes: Shift, Jump and User.
DATA CONTROL
DATA CONTROL
<R.SHIFT>
MODE:OFF
1
2
3
4
OFF
SHIFT
JUMP
USER
69
1 Off
Turns off the Registration Shift assignment.
DATA CONTROL
DATA CONTROL
<R.SHIFT>
MODE:OFF
2 Shift
Selects the Shift mode. In the Shift mode, each press of the Right Footswitch
selects the Registration Memory presets in their numerical order. The
numbered buttons light up as they are selected.
DATA CONTROL
DATA CONTROL
<R.SHIFT>
MODE:SHIFT
1˘ 2
5
NOTE:
Registration Memory
• Although the number of the Registration
Memory buttons of EL-100 is limited to
eight, from Registration Memory 1
through Registration Memory 8, you can
select the other eight Registration
Memory numbers, the Registration
Memory 9 through Registration Memory
16.
• After the last preset is reached, the
function “wraps around” to select the
first preset again.
• The current registration number and the
number next to it will be displayed.
3 Jump
Selects the Jump mode. In the Jump mode, each press of the Right
Footswitch selects a specified panel registration.
■ To set the Jump mode:
1. When you select the Jump mode, one of the registration numbers
will be displayed at the right side of the display.
DATA CONTROL
DATA CONTROL
<R.SHIFT>
MODE:JUMP
REGIST: 1
2. Select the registration number to which you want to jump using the
bottom right Data Control buttons. Each press of the bottom right
Data Control buttons selects next number.
3. Pressing the Right Footswitch jumps to select the designated panel
registration.
NOTE:
Although the number of the Registration
Memory buttons of EL-100 are limited to
eight, from Registration Memory 1
through Registration Memory 8, you can
select the other eight Registration Memory
numbers, the Registration Memory 9
through Registration Memory 16.
70
4 User
Selects the User mode. In the User mode, each press of the Right Footswitch
selects registrations according to the order you specify.
1. When you select the User mode, the Shift End selector function,
how the Registration Shift function acts when it reaches to the end,
will be added to the right side of the display. Also, page number
will be shown at the top right side.
DATA CONTROL
DATA CONTROL
<R.SHIFT>
MODE:USER
<S.END> ⁄
STOP
STOP
TOP
NEXT SONG
2. Select the Shift End type using the bottom right Data Control
buttons. The following three types are available:
Stop: Selects the last registration and quits the operation.
Next Song: After reaching the last preset, then automatically calls
up the registration data of the next song. This function is handy for
you to play a song containing more than 16 registrations.
Recording the songs onto the M.D.R. using this function allows you
to play back them successively.
3. Press the Page buttons to select Page 2. The following display
appears. You can edit the registration shift settings of your own
here.
1 -1 1 -4
2 -1 2 -2
DATA CONTROL
DATA CONTROL
5
Always press the PLAY button to start the
songs and activate the Next Song function
on the M.D.R. The CUSTOM PLAY
button will not cause to activate the Next
Song function.
Registration Memory
Top: After reaching the last preset, then selects the first preset again
and repeats the operation.
NOTE:
NOTE:
Using the Next Song function will not read
the User rhythm patterns/sequences while
playing back a rhythm.
NOTE:
The cursor cannot be moved unless
registration numbers have been entered.
NOTE:
<R.SHIFT>[INS][DEL]¤
T_
1¯?????????????????
The registration to which the cursor is
currently positioned is set on the Electone.
However, moving the cursor cannot
activate the Shift End function.
Cursor
1 -2 1 -3
1 -2 1 -3
NOTE:
1 POSITION (Cursor Controls)
1 -1
1 -2
1 -3
1 -4
Moves the cursor to the first position.
Moves the cursor one step to the left.
Moves the cursor one step to the right.
Moves the cursor to the last position.
Up to 80 steps can be memorized.
Although the number of registrations
shown in the display at a time is limited,
the display scrolls to the right to show the
currently entered registration number as
you enter them.
NOTE:
The Shift End mark will automatically be
put at the end of the registrations you
entered.
N
¯
NEXT SONG
TOP
71
2 Data (Data Controls)
The pair of the top right Data Control buttons is used to enter or
delete registration numbers in the registration row. Move the cursor
to the desired position and edit the registration data.
2 -1 [INS] Insert
For initially entering a registration or inserting a registration
number just before the current cursor position.
First, move the cursor to the position at which you want to
insert. Then press the desired Registration Memory button
(the lamp above the selected button will light), and press the
Data Control button corresponding to INS. The new
registration number is inserted at the cursor position and all
other numbers to the right of the cursor are moved to
accommodate the new number.
2 -2 [DEL] Delete
For deleting a registration number at the current cursor
position. To delete the unnecessary number, move the cursor
to a numbered position and press the Data Control button
corresponding to DEL.
5
Registration Memory
Registration numbers cannot be entered beyond the
Registration Shift function’s capacity of 80. END will
automatically be placed at the end of the registration shift
setting. The following message momentarily appears when
the 80 spaces have been filled: First delete unnecessary
registrations, then perform the operation again.
DATA CONTROL
DATA CONTROL
≥
≥
72
Data Full!
≥
≥
6 Music Disk Recorder (M.D.R.)
The Music Disk Recorder (M.D.R.) lets you store the registration data and load back to the Electone as well as
record your performance and play back the data. Moreover, the M.D.R. allows you to execute song copy
operation and play back commercially available XG song data.
1 Precautions on M.D.R.
Follow the important precautions below.
To eject a floppy disk:
Compatible Disk Type
3.5" 2DD and 2HD type floppy disks can be used.
Inserting/Ejecting Floppy Disks
■ To insert a floppy disk into the disk drive:
Hold the disk so that the label of the disk is facing
upward and the sliding shutter is facing forward,
towards the disk slot. Carefully insert the disk into the
slot, slowly pushing it all the way in until it clicks into
place and the eject button pops out.
Press the eject button slowly as far as it will go;
the disk will automatically pop out. When the
disk is fully ejected, carefully remove it by
hand.
Never attempt to remove the disk or turn the
power off during recording, reading and
playing back. Doing so can damage the disk
and possibly the disk drive.
6
Music Disk Recorder
If the eject button is pressed too quickly, or if it
is not pressed in as far as it will go, the disk
may not eject properly. The eject button may
become stuck in a half-pressed position with the
disk extending from the drive slot by only a few
millimeters. If this happens, do not attempt to
pull out the partially ejected disk, since using
force in this situation can damage the disk drive
mechanism or the floppy disk.
Floppy disk slot
LED (Lamp in-use)
Be sure to confirm that the lamp of STOP
button on M.D.R. is turned off before ejecting a
floppy disk from the slot. Never eject the
floppy disk before the STOP lamp lights up.
Eject button
NOTE:
When the EL-100 is turned on, the LED below the floppy disk
slot will be lit indicating that the M.D.R. is ready to use.
To remove a partially ejected disk, try pressing
the eject button once again, or push the disk
back into the slot and then repeat the eject
procedure.
Be sure to remove the floppy disk from the
disk drive before turning off the power. A
floppy disk left in the drive for extended
periods can easily pick up dust and dirt that
can cause data read and write errors.
73
Cleaning the Disk Drive Read/Write Head
● This instrument employs a precision read/write
magnetic head. The magnetic head will pick up a
layer of magnetic particles from the disks for an
extended period of time. The stained magnetic head
will eventually cause read and write errors.
● To maintain the disk drive in optimum working
order Yamaha recommends that you use a commercially available dry-type head-cleaning disk to clean
the head about once a month.
■ To protect your data (Write-protect Tab):
To prevent accidental erasure of important data, slide
the disk’s write-protect tab to the “protect” position
(tab open).If you attempt to modify the disk when
the write-protect tab is set to “on” position, “Prot
(Protected)” will appear on the LED display in the
M.D.R. section indicating that the operation is not
possible.
Also please check if the write-protect tab is set to
“off” position when you record data.
Protect Off
(tab closed: unlocked)
NOTE:
Rear side
Ask your Yamaha dealer about the availability of proper headcleaning disk.
Shutter
About the Floppy Disks
■ To handle floppy disks with care:
Do not place heavy objects on a disk or bend or
apply pressure to the disk in any way. Always
keep floppy disks in their protective cases when
they are not in use.
6
Music Disk Recorder
Do not expose the disk to direct sunlight,
extremely high or low temperatures, or excessive humidity, dust or liquids.
Do not open the sliding shutter and touch the
exposed surface of the floppy disk inside.
Do not expose the disk to magnetic fields, such
as those produced by televisions, speakers,
motors, etc., since magnetic fields can partially
or completely erase data on the disk, rendering
it unreadable.
Never use a floppy disk with a deformed shutter
or housing.
Do not attach anything other than the provided
labels to a floppy disk. Also make sure that
labels are attached in the proper location.
Write-protect tab
Protect On
(tab open: locked)
■ Data backup
Yamaha recommends that you keep two copies of
important data on separate floppy disks by using this
function. To make a backup disk use the Disk Copy
function on page 92.
Improved Potentiality of the M.D.R.
The M.D.R. of the EL-100 begins reading all data
as soon as you insert a disk into the floppy disk slot.
Thus, inserting a disk causes to produce a sound
(reading sound) indicating that the M.D.R. is in the
reading process.
The improvement of the M.D.R. allows you to start
song playback immediately, to be free from the
reading sound during playback and to record the
song playback using the several song numbers with
the Next Song function.
NOTE:
Ejecting the disk will lose the data loaded from the disk except
for the currently selected and played back song.
NOTE:
The time reading sound is produced is in proportion to the
amount of data recorded in the disk. You can eject the disk
whenever you are not using the M.D.R. and don’t want to be
bothered with the reading sound.
74
2 Formatting a Disk
Before recording, the disk must first be formatted.
RECORD
1
UPPER
Put the disk, label facing up, into the disk drive (floppy disk slot).
“Fort” will appear on the LED display indicating that the
inserted disk requires to be formatted.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG DEL.
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
RECORD
2
UPPER
While holding down the SHIFT button, press the FORMAT
button.
This step puts the format operation on stand-by, indicated by the
dashes on the LED display and the flashing LED (lamp) above
the FORMAT button.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
RECORD
3
UPPER
<SONG NAME>
01:
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
PLAY
6
SONG DEL.
FROM
TO
SONG COPY
STOP
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
Music Disk Recorder
Press the FORMAT button again to begin formatting.
Formatting is engaged and the LED above the FORMAT button
stays lit.
The number “160” appears on the LED display and counts down
to “001” as the disk is being formatted. When formatting is
completed, operation returns to the original STOP status.
The following Song Name display appears after the operation.
LOWER
MUSIC DISK RECORDER
⁄
The song number can be selected using SONG SELECT button
or the Data Control buttons on the bottom row. Up to 10 song
numbers can be selectable in a single page. The page numbers,
from 1 through 4, are also shown at the top right side of the
display. A total of 40 song locations are created. The song
names next to each song number are left blank and indicate that
each song number doesn’t contain any data.
Formatting a disk erases all the data in the disk and
makes it ready to record. The erased data by
formatting will be lost permanently. Check if the
disk contains your important data, or not, before
executing the operation.
About SHIFT Button
You will find the SHIFT button (printed in green) at the top right
side of the M.D.R. section. Some buttons in the M.D.R. section have
dual functions: the first function is printed in white above each
button; the second function is printed in green below each button.
The SHIFT button is used to select the second functions by pressing
each function button while holding down the SHIFT.
75
3 Recording
1) To record a song:
1
Set the desired registrations on the Electone. Make all the
Electone settings necessary for the song you will record. This
means entering the all registrations you will need for the entire
performance in the Registration Memory. Make sure also to
select the registration that you will use at the beginning of the
song.
2
3
Put a formatted disk into the disk slot.
NOTE:
The song numbers 01 through 40 are available and
up to 40 songs can be stored on a disk. However,
available song numbers may be reduced depending
on the amount of the song data you have recorded.
See page 94 for the information about the total
amount of memory left on a floppy disk.
RECORD
UPPER
LOWER
SONG
REPEAT
Use the SONG SELECT (G, H) buttons to select the song
number for recording. You can also select the song number by
pressing the Data Control buttons.
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
DATA CONTROL
6
DATA CONTROL
<SONG NAME>
01:
⁄
Music Disk Recorder
RECORD
UPPER
4
Press the RECORD button.
The RECORD lamp lights up and the PLAY and CUSTOM
PLAY lamps begins blinking, indicating that the Music Disk
Recorder is ready to record.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
NOTE:
If the selected song number already contains
recorded data, small bars (“--”) appear at the left
part of LED display and flash along with the song
number, warning you that the selected song number
already contains recorded data. If you want to
execute recording operation over the song number,
press the RECORD button again. If you don’t
want, select another song number for recording or
press the STOP button to cancel recording.
RECORD
5
UPPER
Press the PLAY button.
The PLAY lamp lights up and small bars flash across the LED
display from left to right. This indicates M.D.R. is reading the
registrations and other settings.
SONG
REPEAT
PAUSE
LOWER
PLAY
PEDAL CONTROL UPPER
PEDAL CONTROL
STOP
PLAY
SHIFT
SONG DEL.
TO
FROM
SONG COPY
MUSIC DISK RECORDER
76
LOWER
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
RECORD
6
UPPER
After numbers appear on the LED display of the M.D.R., begin
playing.
Once the setup operation in step #5 is complete, a number will
appear on the LED display indicating that you can begin
recording your performance. The number also indicates the
amount of memory left on the disk.
LOWER
SONG
REPEAT
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
PAUSE
STOP
SHIFT
PLAY
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
NOTE:
The short time it takes to set up for recording is
recorded as well, causing a short pause before
playback of the song.
If you make a mistake during recording:
RECORD
UPPER
1. Press the PLAY button while the M.D.R. is still running.
This stops the recording and returns you to the starting point of
the song.
The letters “rE” (retry) appear on the left side of the LED display
and the PLAY and CUSTOM PLAY LEDs start flashing,
indicating that you can re-record the song.
LOWER
SONG
REPEAT
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
PAUSE
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
2. Press PLAY again to begin re-recording the song.
Re-recording starts from the beginning of the song and replaces
the previously recorded performance with the newly recorded
performance.
6
7
When you finish playing, press the STOP button.
After the small bars flash to draw a square on the LED to
indicate the processing for stop, the STOP lamp lights up,
indicating the recording process is finished.
The song number will be displayed on the LCD display,
indicating that the number contains recorded data.
SONG
REPEAT
PAUSE
LOWER
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
PLAY
SHIFT
SONG DEL.
FROM
TO
SONG COPY
STOP
Music Disk Recorder
RECORD
UPPER
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
Indicates the M.D.R. is in the stop process.
<SONG NAME>
01:SONG 1
⁄
Never eject the floppy disk before the STOP lamp
lights up.
NOTE:
When the available memory reaches “008” or less,
the numbers begin flashing to warn you. If this
happens, stop recording before the display reaches
“000.”
8
To hear your newly recorded performance, press the PLAY
button.
Play back will begin after a couple of seconds. For more
information on playback and other playback-related functions,
see page 84.
Never attempt to press the eject button or turn
the power off during recording, reading and
playing back. Doing so can damage the disk
and possibly the disk drive. Be sure to
remove the floppy disk from the disk drive
before turning off the power.
77
Outline of M.D.R. Operation
Though the M.D.R. is as easy to operate as a cassette tape recorder, it is far move versatile. Since it records all
Electone settings and control movements as well as the notes you play as digital data, it allows you much more
flexibility and control than even the most sophisticated tape recorder. Basically, the M.D.R. independently
records the following three types of data:
Registration data (including Bulk data)
All registrations stored to the Registration Memory numbered buttons as well as the registration currently set to
the panel, are recorded at the beginning of a song, before the actual recording of your performance. Bulk data is
also saved to the song with the Registration data. Bulk data includes: Registration Shift settings, and Rhythm
Pattern (User rhythms) and Rhythm Sequence data.
Performance data
The M.D.R. records your performance on the keyboards and pedalboard of the Electone exactly as you play it,
even recording the strength at which you play the keys and how hard you press them down while playing. The
various types of performance data – Upper, Lower, Pedal and Lead – are recorded to independent “tracks,” so that
you can change any one of them without affecting the others.
Control data
All changes you make on the Electone during your performance are recorded in real time. These include
registration changes, the use of the expression pedals and footswitches.
6
Music Disk Recorder
78
2) To record each part separately:
You can also record the parts of your performance independently; for
example, first recording the chords and bass to the song (using the Lower
and Pedalboard), and after that recording the melody (using the Upper
Keyboard). This function also lets you record the lead voice, keyboard
percussion and performance control data, such as registration changes
and expression pedal operation, separately from the other parts of the
song.
1
Set up the M.D.R. for recording, as you did in the section above.
The first steps in recording parts separately are the same as for
normal recording on page 76:
1. Memorize all the registrations needed for your performance
to the Registration Memory numbered buttons, and set the
registration that will be used at the beginning of the song.
2. Insert a formatted disk.
3. Select the song number to which you will record your
performance.
4. Press the RECORD button to make the Music Disk Recorder
ready to record.
RECORD
UPPER
SONG
REPEAT
PAUSE
LOWER
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
Music Disk Recorder
2
Select the parts for recording.
Pressing the RECORD in the procedure 1-4. above turns on the
all parts’ LEDs in the upper left row indicating that each part is
ready to record.
Press the RECORD buttons for each part in the upper left row to
turn off the parts you don’t want to record. For this example,
press RECORD/UPPER, the PLAY/UPPER lamp in the upper
right row lights up.
6
PLAY
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
■ RECORD/UPPER
Records the performance data of the Upper keyboard when
turned on. Recording is cancelled when turned off.
■ RECORD/LOWER
Records the performance data of the Lower keyboard when
turned on. Recording is cancelled when turned off.
■ RECORD/PEDAL
Records the performance data of the Pedalboard when turned
on. Recording is cancelled when turned off.
■ RECORD/CONTROL
Records the control data when turned on. Recording is
cancelled when turned off.
(See Outline of M.D.R. Operation on the previous page.)
This example operation disables recording of the Upper part.
79
Separate recording for Lead Voice and/or Keyboard Percussion parts:
The Lead voice and the Keyboard Percussion can be recorded/played
back separately although they are not shown on the M.D.R. panel.
Separate recording for Lead Voice and/or Keyboard
Percussion parts:
Hold down the SHIFT button and simultaneously press the
appropriate button in the top row in the procedure #2 above. The
two buttons (indicated in the illustration at the right) function as
Lead Voice and Keyboard Percussion selectors in the record mode.
■ RECORD/LEAD
Records the performance data of the Lead voice when turned on.
Recording is cancelled when turned off.
■ RECORD/K.PERC.
Records the performance data of the Keyboard Percussion when
turned on. Recording is cancelled when turned off. Keyboard
percussion can be recorded/played back independently from
rhythm section.
3
4
6
RECORD
PLAY
SHIFT
(LEAD)
(K.PERC.)
(LEAD)
(K.PERC.)
PAUSE
REM.MEM.
NOTE:
If you don’t record the Lead Voice and Keyboard
Percussion parts separately, the Lead part will be
recorded as the Upper data and the Keyboard
Percussion part will be recorded as the Lower/
Pedal data.
Press the PLAY button, and start playing after numbers appear
in the display. For this example, play the lower keyboard and
pedalboard.
Music Disk Recorder
Press the STOP button when you are finished with your performance to stop recording.
Now that you’ve recorded the first parts of your performance.
Press the RECORD button to set up recording of the next part,
Upper part in this case.
RECORD
5
UPPER
Press the RECORD button.
In this case, the song (number) contains the performance data of
the Lower and Pedal in addition to the registration and setup
data. The small bars (“--”) appear at the left part of LED display
and flash along with the song number, warning you that the
selected song number already contains recorded data.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
STOP
PLAY
SHIFT
SONG DEL.
FROM
TO
SONG COPY
SONG SELECT
RECORD
TEMPO
FORMAT
RECORD
6
PEDAL CONTROL
CUSTOM PLAY
MUSIC DISK RECORDER
UPPER
Press the RECORD button again to record another part (Upper
part).
The RECORD lamp lights up and the PLAY and CUSTOM
PLAY lamps begins blinking, indicating that the Music Disk
Recorder is ready to record.
LOWER
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
RECORD
7
UPPER
Press the RECORD buttons for each part in the upper left row to
turn off the parts you have already recorded.
In this case, press RECORD/LOWER, RECORD/PEDAL and
RECORD/CONTROL to turn them off.
SONG
REPEAT
PAUSE
LOWER
PLAY
PEDAL CONTROL UPPER
PEDAL CONTROL
STOP
PLAY
SHIFT
SONG DEL.
FROM
TO
SONG COPY
MUSIC DISK RECORDER
80
LOWER
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
RECORD
8
UPPER
Press the CUSTOM PLAY button to start recording of the new
part or parts (Upper part).
Playback of the previously recorded parts starts immediately.
The CUSTOM PLAY button is used here to record only the
parts that have been selected for recording, and play back only
those parts that have been selected for playback. While you
listen to the parts being played back, start playing the melody on
the Upper keyboard.
Since registration data has already been recorded with the first
parts of the song, recording begins immediately.
When the end of the recorded performance is reached, playback
is automatically stopped and the STOP status is resumed.
SONG
REPEAT
PAUSE
LOWER
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
NOTE:
The CUSTOM PLAY button is used to record or
play back the parts and data other than the
registration data.
NOTE:
The length of a subsequently recorded part cannot
exceed the length of the previously recorded parts.
If you want to change the song length, first delete
the existing song (see Song Delete on page 92) and
record again.
Punch-in Recording
6
You can retry to change specified measure(s) or a specific part you
don’t want to use.
Music Disk Recorder
1. Press the PLAY button to start playback of the song containing
the part you want to change.
2. Press the PAUSE button at the point you want to execute punchin recording. The current song is stopped momentarily.
3. Press the RECORD button. The PLAY and CUSTOM PLAY
lamps begins blinking, indicating that the Music Disk Recorder is
ready to record.
4. Press the RECORD buttons for each part in the upper left row to
turn off the parts you want to keep as they are. (Only the part you
want to do punch-in recording should be turned on.)
5. Press the PLAY button to start punch-in recording. Play the
specified range you want to change.
6. Press the STOP button to quit the Punch-in recording function as
soon as you reach the end of the range.
81
4 Recording Registrations
(and Bulk Data)
You can also record registrations by themselves, without recording a
performance. Bulk data, including Registration Memory,
Registration Shift settings, Rhythm Pattern (User rhythms), and
Rhythm Sequence data, are also saved in the operation. There are
two ways to record the registrations and bulk data:
[1]
1
2
3
6
On the Electone, set the registrations and all other data you want
to record.
Select the song number to which you wish to record the registrations.
RECORD
UPPER
While holding down the RECORD button, press the M./TO
DISK (Memory) button on the Registration Memory panel.
Small bars flash across the LED display from left to right,
indicating that the M.D.R. is reading the registrations and other
settings. After recording, the M.D.R. is automatically stopped
and returns to STOP status.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
SHIFT
PLAY
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
Music Disk Recorder
1. While holding down the RECORD button...
2. Press the M./TO DISK (Memory) button.
REGISTRATION MEMORY
M.
/ TO DISK
1
2
3
4
5
6
[2]
1
2
Set up the registrations and select the song number as you did in
steps #1 and #2 above.
RECORD
UPPER
LOWER
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SHIFT
Press the RECORD button to make the M.D.R. ready to record.
SONG
REPEAT
PAUSE
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
RECORD
3
82
Press the PLAY button to record the registrations, then press the
STOP button as soon as you see the small bars flash across the
LED display from left to right.
This is the same procedure as the one when you start recording.
The small bars that flash across the display indicate that the
M.D.R. is recording the registrations and being set up for normal
recording; pressing the STOP button interrupts this process.
UPPER
SONG
REPEAT
PAUSE
LOWER
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
MUSIC DISK RECORDER
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
5 Recalling Recorded
Registrations (and Bulk Data)
The registrations (and bulk data) recorded to song numbers in the
above operation can be loaded back to the Electone by simply
selecting the appropriate song number and pressing the PLAY
button. When the operation has been completed, the M.D.R. returns
to STOP status.
1
2
Insert the disk and select the song number you want to load back
to the Eelectone.
Press the PLAY button.
Using More Than 8 Registrations
The M.D.R. makes it possible to use more than 8 registrations (8
Registration Memory locations) in a performance, — without having
to alter the current panel settings. A disk can accommodate 40 song
numbers and each song number can contain 8 registrations.
6
Music Disk Recorder
To play a performance using more than 16 different
registrations:
1. First record the registrations you need into several song numbers
on the M.D.R. before the performance. (You should also try to
record them in the order that you’ll use them, if possible.)
2. During the performance, after all 8 registrations from a certain
song number have been used, select the next song number and
press the PLAY button on the M.D.R. This replaces all 8
registrations in Registration Memory with the new ones from the
selected song number.
3. By repeating the above steps, you can run through an entire
performance without having to change the panel settings.
NOTE:
Selecting the Next Song in the User Registration
Shift settings makes it possible to have the M.D.R.
automatically read the 8 registrations in the next
song number. See page 71 for more information.
6 Replacing Registrations
The M.D.R. also lets you change the registrations of an existing song
without changing the performance data. The procedure is the same
as that of Recording Registrations mentioned in the previous page.
83
7 Playback
You can play back your recorded performance by simply pressing
the PLAY button. Registrations and other data will be recalled to the
Electone.
1) To play back a song:
1
RECORD
Select the number of the song you want to play back by using
the SONG SELECT buttons. You can also select the song
number by pressing the appropriate Data Control buttons.
UPPER
SONG
REPEAT
PAUSE
<SONG NAME>
03:SONG 3
LOWER
PLAY
PEDAL CONTROL UPPER
PEDAL CONTROL
STOP
PLAY
SHIFT
SONG DEL.
FROM
TO
SONG COPY
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
⁄
MUSIC DISK RECORDER
RECORD
2
LOWER
UPPER
Press the PLAY button to begin playback of the song.
The PLAY lamp lights up and small bars move across the
display, indicating that the M.D.R. is resetting registrations on
the Electone.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
RECORD
3
6
UPPER
Music Disk Recorder
Playback starts automatically after reading the song data. The
elapsed time will be displayed on the LED.
Playback automatically stops at the end of a song. You can,
however, stop playback in the middle of a song by pressing the
STOP button.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
If you have recorded the Lead Voice/Keyboard
Percussion part separately:
On the EL-100 the Lead/Keyboard Percussion part(s) you have
recorded separately will automatically set to on when you start
playback.
NOTE:
When you play back the data made with other
Electone models such as EL-90/87 and which
includes the separately recorded Lead/Keyboard
Percussion part(s), Lead part will be off and
Keyboard Percussion will be on as the defaults.
(To turn on the Lead part, press PLAY/UPPER
while holding down the SHIFT.)
2) To play back the selected part(s):
You can also play back the selected parts of your recorded performance,
while other parts are temporarily turned off. This function is especially
useful for playing a single part, such as the melody, over previously
recorded accompaniment parts.
1
2
84
Select the number of the song to be played back.
RECORD
UPPER
Set the parts you wish to mute to off, by pressing the appropriate
PLAY button in the upper right row. The LED of the selected
part should be off.
Make sure to turn on the parts you wish to play back.
SONG
REPEAT
PAUSE
LOWER
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
MUSIC DISK RECORDER
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
3
Press the PLAY button to begin playback of the song.
First the registration and other data are read, then playback of
the performance starts (excepting the parts that were turned off
in step #2).
4
Now perform your new part or parts over the playback parts.
When the end of the recorded performance is reached, playback
is automatically stopped and the STOP status is resumed.
3) To repeat playback of a song or songs:
This feature allows you to repeatedly play back either all songs on a disk
or only one specific song.
1
RECORD
UPPER
Select the song number you wish to play back.
If you wish to play back all songs on a disk, select the first song
that will be played back. The others will follow in order.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
RECORD
2
UPPER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
PLAY
6
SONG DEL.
FROM
TO
SONG COPY
STOP
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
Music Disk Recorder
Hold down the SHIFT button and simultaneously press the
SONG REPEAT button.
The lamps above SHIFT and SONG REPEAT light up, and
“ALL” appears on the LED display.
LOWER
CUSTOM PLAY
MUSIC DISK RECORDER
3
To repeatedly playback all songs starting with the
selected song:
Press the PLAY button to begin playback of the song.
Playback will begin from the song selected and repeat
indefinitely.
To repeatedly play back only the selected song:
1. Again hold down the SHIFT button and simultaneously press
the SONG REPEAT button.
“SinG” appears on the LED display to indicate that a single
song will be repeatedly played back.
RECORD
UPPER
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
RECORD
2. Press the PLAY button to begin playback of the song.
Playback of the selected song will begin and repeat
indefinitely.
UPPER
SONG
REPEAT
PAUSE
LOWER
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
To stop playback, press the STOP button.
MUSIC DISK RECORDER
85
About XG
The EL-100 allows you to play back the commercially available XG
song data using the M.D.R. Also, the XG Easy Converter function of
the EL-100 lets you convert the data to the XG compatible data.
NOTE:
The XG song data created with EL-100 conforms
to the SMF format 0 or 1.
Playing back the XG Song Data
This function is for playback only. You can practice a specific part
of the XG song data by muting that part.
NOTE:
1. Insert the XG song disk into the floppy disk slot.
The following display appears.
Total amount of reverb value may be changed
inadvertently while playing back XG Song Data.
Song Name Display
2
DATA CONTROL
DATA CONTROL
1 Selects a song.
2 Change the LCD to Part
Display.
<SONG NAME> [PART]˛˝
01:AMBIENT.MID
[XG] page will be added to
the upper right side of the
display.
1
The XG song data will be displayed on the XG page. You can
store both the XG songs (on the XG page) and Electone songs
(on pages 1 - 4) in a single disk.
6
Music Disk Recorder
2. Use the bottom left Data Control buttons 1 to select a song you
want to play back.
3. Press the PLAY button in the M.D.R. section to start song
playback.
4. Use the top right Data Control buttons 2 to change the LCD to
part display.
Part Display
3
4
DATA CONTROL
3 -2 3 -1
DATA CONTROL
PART:ALL
[NAME]˛˝
’SOLO ’MUTE VOL.:24
5
6
7
Use 3 button to select a part, and press 5 to engage the solo
playback of the selected part, press 6 to mute some parts or
press 7 buttons to adjust the volume of a specific part.
86
3 Selects a part. Range: 1 16, ALL (all parts)
3 -1 Select next part.
3 -2 Select previous part.
4 Change the LCD to Song
Name Display.
5 Solo: Use the
corresponding Data
Control button to turn on/
off the solo function.
When solo is turned on all
other parts will be muted
automatically.
6 Mute: Use the
corresponding Data
Control button to turn on/
off the mute function.
7 VOL. (VOLUME):
Adjusts the volume of
each part within the range,
0 - 24. If you have
selected ALL, you can
adjust overall volume.
XG Easy Converter
This function allows you to convert the EL-100 song data to the XG
format data. You can then play back the data using XG devices and/
or personal computer. Depending on the type of XG devices, sound
may be different from the original data you created.
The contents to be converted:
Voice (Program) number, Volume, Feet (octave settings), Pan, Vibrato, Slide (for the
Lead voices), Initial Touch, Effects (Tremolo and Delay), Reverb (except for
Length), Sustain, Rhythm Patterns (except for Accompaniment), Expression,
Registration, Registration Shift (except for Next Song)
To convert the EL-100 data to the XG song data:
1. Insert the disk containing the Electone data into the floppy disk
slot.
2. Select the song to be converted to the XG data.
3. While holding down the top right Data Control buttons press the
RECORD button in the M.D.R. section.
The following message appears to confirm the operation.
NOTE:
Confirm that the disk should contain enough
amount of available memory before the
conversion.
RECORD
DATA CONTROL
PLAY
DATA CONTROL
UPPER
≥Confirm Conv.Data ≥
≥ [CONFIRM][CANCEL]≥
SONG
REPEAT
PAUSE
≥Conv.to XGSONG01? ≥
≥ [CONV.] [CANCEL]≥
5. Press the Data Control buttons corresponding to [Convert].
After the process of the conversion the LCD returns to the
original display.
<SONG NAME> [PART]˛˝
01:XGSONG01.MID
When the XG song data is newly created in the disk, XG page
will be added to the top right side of the display. The converted
song (XG data) will be stored on the XG page and the original
song (Electone data) is left as is.
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
PLAY
6
SONG DEL.
TO
FROM
SONG COPY
STOP
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
Music Disk Recorder
4. Press the Data Control buttons corresponding to [Confirm].
The M.D.R. starts playback of the selected song for you to decide
whether you convert it to the XG data, or not. After finishing
playback the following message appears.
LOWER
MUSIC DISK RECORDER
NOTE:
In this case the M.D.R. uses the XG tone generator
built in the EL-100 to play back the data.
NOTE:
Select [Cancel] to abort the operation and return
to the original display.
NOTE:
The converted XG song data may sound
differently from the original data.
NOTE:
The converted data cannot be deleted.
87
8 Other Functions
1) Custom Play
If you want to play back the song without resetting the registrations and
other data, press the CUSTOM PLAY button.
This displays the song time and starts playback immediately.
RECORD
UPPER
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
NOTE:
If you hold down the SHIFT and press CUSTOM
PLAY or if you execute the following Read and
Auto Increment function, all data, except for that of
Rhythm Pattern Program, Rhythm Sequence and
Keyboard Percussion assignment, will be loaded
and played back. It is handy when you want to call
up the registrations only.
2) Read and Auto Increment
6
RECORD
UPPER
Another method for calling up only registration data, besides that
mentioned in the NOTE above.
Music Disk Recorder
Pressing the UPPER button in the RECORD section while M.D.R. is in
the stop status calls up the registration data and automatically selects the
next song number.
This method is more convenient than the one mentioned above since the
M.D.R. automatically selects the next song number.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
NOTE:
This function is not possible if the next song
contains no registration data.
3) Pause
RECORD
UPPER
If you want to temporarily stop playback of the song or songs, press the
PAUSE button.
To resume playback from the point at which the song was paused, press
the PAUSE button again.
SONG
REPEAT
PAUSE
LOWER
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
4) Fast Forward and Fast Reverse
During playback, these buttons function as fast forward and fast reverse
buttons, much like those of a tape recorder.
Press SONG SELECT H button to advance to a later point in the song
or press SONG SELECT G button to return to an earlier position.
While either of these buttons is held down, playback stops and the song
time is advanced or reversed accordingly.
Even when the button is released, playback is paused. To resume
playback from the point you’ve advanced or reversed to, press the PLAY
button.
88
NOTE:
It may take some time to search the point at which
you want to resume playback when you return to an
earlier position using the fast reverse function.
NOTE:
Fast Forward and Fast Reverse operate at five
times the normal playback speed.
5) Changing the Tempo
RECORD
UPPER
LOWER
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SHIFT
You can change the tempo of the song as the song is playing back.
While holding down the SHIFT button, press the TEMPO + or TEMPO button.
Each press of the button slows down or speeds up the tempo by a small
amount (not affecting the pitch).
Pressing TEMPO + causes the song faster and TEMPO – slower.
(The Tempo button on the Electone panel cannot be used to change the
tempo on the Music Disk Recorder.)
To restore the original recording tempo of a song, hold down the SHIFT
button and simultaneously press both TEMPO buttons.
SONG
REPEAT
PAUSE
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
NOTE:
When tempo is changed, the LED display indicates
the change as a percentage of the original recorded
tempo (100). Values less than 100 indicate a
slower tempo; values greater than 100 indicate a
faster tempo.
RECORD
PLAY
Indicates faster tempo
UPPER
SONG
REPEAT
Indicates original tempo
PAUSE
LOWER
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
6
Indicates slower tempo
NOTE:
Music Disk Recorder
Tempo change remains in effect even when you
change songs. If you have changed the tempo in
one song, you should perform above step to restore
the original tempo before playing another song.
Turning the power switch off and on again also
restores the original tempo.
89
6) Song Copy
This function lets you copy the data recorded at one song number to
another song number. You can copy and exchange the data even between
two different disks.
To use the Song Copy function within a disk:
Select the song number to be copied (source) with the SONG
SELECT buttons.
1
2
NOTE:
This function is available with the Electone data
only, not with the XG data.
RECORD
UPPER
LOWER
SONG
REPEAT
PAUSE
While holding down the SHIFT button, press the SONG COPY
FROM button.
The song number to be copied from appears at the left of the
LED display.
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
NOTE:
If the specified song number has no recorded data,
the M.D.R. automatically searches for and selects
the next song that contains recorded data.
RECORD
3
6
UPPER
Music Disk Recorder
Next, designate the destination song number. While holding
down the SHIFT button, press the SONG COPY TO button.
The M.D.R. automatically searches for an empty song number to
copy the data to, and displays that number at the right side of the
display. The RECORD lamp will start flashing indicating that
the M.D.R. is ready to copy. If all songs numbers contain
recorded data, “FULL” appears on the LED display. In this
case, you should erase one of the songs on the disk by using the
Song Delete function (page 92).
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
NOTE:
The message “FULL” may appear when the
available memory is short.
NOTE:
If you want to abort the operation, press STOP
button.
4
Use the SONG SELECT buttons to select a destination song
number for copying. Follow this step if you wish to select a
different destination song number than the one displayed.
The M.D.R. will display only those song numbers that have no
data.
RECORD
5
90
UPPER
Press the RECORD button to execute the Song Copy function.
The RECORD lamp stops flashing and remains lit, indicating
that the Song Copy function is in process. The LED display
shows the “size” of the song in numbers, and counts down as the
data is being copied. When the display shows “000,” the song
has been completely copied.
SONG
REPEAT
PAUSE
LOWER
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
MUSIC DISK RECORDER
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
To use the Song Copy function between two different disks:
Insert the source disk that contains the song you want to copy
from.
1
2
RECORD
UPPER
While holding down the SHIFT button, press the SONG COPY
FROM button.
The song number to be copied from appears at the left of the
LED display.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
3
Use the SONG SELECT buttons to select a destination song
number for copying.
NOTE:
You can also use the Data Control buttons to select
the song number.
RECORD
4
UPPER
Press the RECORD button.
The RECORD lamp lights up and the LED continues to indicate
“00.--” as shown at the right.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
6
MUSIC DISK RECORDER
6
7
Insert the destination disk to which you want to copy .
NOTE:
Music Disk Recorder
5
Press the Eject button to take out the source disk.
The RECORD lamp remains lit. Although ejecting
the disk while the RECORD lamp is lit is prohibited, you are allowed to eject the disk in this case.
RECORD
UPPER
While holding down the SHIFT button, press the SONG COPY
TO button.
The song number to be copied to appears at the right side of the
LED display. The M.D.R. automatically searches for an empty
song number to copy the data to.
SONG
REPEAT
PAUSE
LOWER
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
8
9
Use the SONG SELECT buttons to select a destination song
number for copying.
Press the RECORD button to execute the Song Copy function.
The LED display shows the “size” of the song in numbers, and
counts down as the data is being copied. When the display
shows “0000,” the song has been completely copied.
NOTE:
An asterisk (*) is added to the end of the (destination) song’s name to differentiate from the original
(source) song.
91
7) Song Delete
You can delete a song on disk by performing this function.
1
2
Use the SONG SELECT buttons to select the number of the
song you wish to delete.
RECORD
UPPER
While holding down the SHIFT button, press the SONG DEL.
button.
The letters “dL” appear on the left side of the LED display, next
to the selected song number. RECORD lamp flashes to indicate
that the M.D.R. is ready to delete the song.
If you wish to, you can still select a different song number in
this step by using the SONG SELECT buttons.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
NOTE:
If you want to abort the operation, press STOP
button.
NOTE:
XG song data cannot be deleted.
3
6
Music Disk Recorder
Press the RECORD button to execute the Song Delete function.
The RECORD lamp stops flashing and remains lit, indicating
that the Song Delete function has begun. When the Song Delete
function is completed, the STOP status is automatically
resumed.
8) Disk Copy
You can duplicate a floppy disk by copying the contents. Yamaha
recommends that you keep two copies of important data on separate
floppy disks by using this function.
1
Prepare the source disk and the formatted blank disk to be
copied.
The disk type of both source disk and destination
disk must be the same. For example, use 2HD for
the disk to be copied (destination) if the source disk
is 2HD type.
Be sure to set the Write-protect tab (page 74) on
the source disk to on. The message “Prot” may
appear if you insert the source disk with the Writeprotect tab “off.” On the contrary, set the Writeprotect tab on the destination disk to off. The
message “Prot” may appear if you insert the
destination disk with the Write-protect tab “on.”
In this case, the Disk Copy function cannot be
executed.
RECORD
2
UPPER
While holding down the SHIFT button, press the LOWER
button in the RECORD part.
“In 1” appears on the LED display to indicate that the M.D.R. is
ready to execute the Disk Copy.
SONG
REPEAT
PAUSE
LOWER
PLAY
PEDAL CONTROL UPPER
PEDAL CONTROL
STOP
PLAY
SHIFT
SONG DEL.
FROM
TO
SONG COPY
MUSIC DISK RECORDER
92
LOWER
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
RECORD
3
UPPER
Insert the source disk into the disk slot.
The M.D.R. starts reading the data in the source disk.
“out 1” appears on the LED display.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
RECORD
4
UPPER
Press the eject button to take out the source disk.
“In 2” appears on the LED display to urge you to insert the
destination disk.
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
RECORD
5
Insert the destination disk.
The number “160” appears on the LED display and counting
down is initiated as the disk is being copied.
When finished, “End” will appear on the LED display for few
seconds.
UPPER
LOWER
SONG
REPEAT
PAUSE
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
CUSTOM PLAY
MUSIC DISK RECORDER
RECORD
UPPER
SONG
REPEAT
PLAY
PEDAL CONTROL UPPER
LOWER
PEDAL CONTROL
SONG DEL.
FROM
TO
SONG COPY
STOP
PLAY
6
SHIFT
SONG SELECT
RECORD
TEMPO
FORMAT
Music Disk Recorder
PAUSE
LOWER
CUSTOM PLAY
MUSIC DISK RECORDER
NOTE:
“Fort” or “bAd” may appear if an error occurs in
the middle of the operation. If this happens, please
retry formatting the destination disk and copying
disk.
Follow the M.D.R. direction to eject/insert the
disks during the operation. Do not eject/insert the
disks frivolously ignoring the M.D.R. direction.
Doing so can damage the disk and possibly the disk
drive.
93
9) Checking the Remaining Memory
RECORD
PLAY
SHIFT
You can check the amount of memory available for additional recording
in a disk by pressing PAUSE button while holding down SHIFT button.
The amount of available memory will be displayed on the LED.
The maximum amount of memory is ca.700 for 2DD disks and ca.1400
for 2HD disks.
(LEAD)
(K.PERC.)
(LEAD)
(K.PERC.)
PAUSE
REM.MEM.
10) Pattern Disks
The M.D.R. also allows you to select rhythms from optional disks.
To load the patterns from a Pattern disk:
Insert the Pattern Disk into the disk slot under the Music Disk
Recorder.
The pattern number and name from the Pattern Disk appears.
1
2
Refer to the pattern list included in the Pattern Disk
for the information on each rhythm.
Select the rhythm you want to use using the appropriate Data
Control buttons.
Jumps
back
10 numbers
6
NOTE:
Jumps
ahead
10 numbers
Save
DATA CONTROL
DATA CONTROL
Music Disk Recorder
<PATTERN DISK>[SAVE]
01:Pop.R-1
Pattern Number
Selects
previous
number
3
94
Pattern Name
Selects
next
number
Start the rhythm to check the pattern to be called up.
Selects
previous
number
Selects
next
number
4
If you want to save the current pattern to a User Rhythm space,
select the “SAVE” with the corresponding Data Control buttons.
The following display appears.
DATA CONTROL
Selects the destination (User Rhythm) number
DATA CONTROL
≥ ÚÆSave to USER1-A≥
≥ [SAVE]
[CANCEL]≥
Execute save
5
6
Select the User number to which you want to save using the top
left Data Control buttons.
Press the Data Control buttons corresponding to [Save].
The rhythm is saved and loaded to the designated User Rhythm
number.
NOTE:
Select [Cancel] to abort the operation and return to
the original display.
NOTE:
See page 50 for the details to use the loaded User
pattern.
6
Music Disk Recorder
11) Copy Protect
Some of the Disks available for the Electone are purposely protected
from being copied or erased. You cannot save the data to another floppy
disk.
If you try to load data from such a “copy-protected” disk to the Electone,
a “Protected Disk” (PrXX*) message will appear on the LED display.
The data cannot be saved to the disk.
*XX: song number
95
Messages on the M.D.R. LED Display
Display
Description of the Messages
No disk is installed. Install a disk.
1) The installed disk is write-protected, so the Record, Song Copy, and Song Delete jobs cannot be
performed. Set the disk’s Write-protect tab (page 74) to OFF.
2) If you are using a copy-protected playback-only disk, this message may appear when you attempt
the Record, Song Copy, or Song Delete operations. Cancel the operation.
3) When executing Disk Copy, set the Write-protect tab on the source disk to ON.
The installed disk is not formatted. Format the disk. (page 75)
1) The disk’s memory capacity is full, so the Record or Song Copy operation cannot be performed.
Use another formatted disk or delete unnecessary data.
2) All of the song numbers contain recorded data, so the Song Copy operation cannot be performed.
Press the STOP button, then delete any unnecessary data.
None of the song numbers contain recorded data, so the Song Copy operation cannot be performed.
Press the STOP button and abort the operation.
An error occurred because the disk was removed during recording or playback. Press the STOP
button, and replace the disk, then start the operation over again.
Incompatible disk has been inserted. Insert the appropriate disk.
Recording cannot be performed because too much data was received at one time. Press the STOP
button and retry recording.
6
The disk is defective and cannot be formatted. Use another disk.
Music Disk Recorder
An error occurred during the transmission or reception of data. Press the STOP button and retry the
operation over again.
You are trying to record to the song number that already contains recorded data. Stop the recording
and select the other blank song number by pressing the SONG SELECT buttons.
XX: song number
When you insert the “copy-protected” disk to the Electone, this message will appear on the LED
display. You cannot overwrite or save the changes.
XX: song number
oooo
This message indicates that an incompatible disk is inserted in the Pattern Disk or Registration
Menu Disk operation. Insert the appropriate disk.
_XX
An under line (_) before the song number indicates that it is XG song data.
XX: song number
or
96
You have inserted a wrong type disk as the destination disk in the Disk Copy operation. Use the
same disk type as the source disk.
7 Footswitches and Expression Pedal
These foot-operated controls allow you to turn on and execute various performance functions without taking
your hands from the keyboards.
1 Footswitch
The Electone has two Footswitches on the expression pedal that can be used
to control various functions.
The Right Footswitch is used for the Registration Shift function. (See page
69 for the details of the Registration Shift function.)
The Left Footswitch can be set to control one of the following functions:
Glide, Tremolo, rhythm controls.
Assignments of the functions to the Left Footswitch are made in the
FOOTSWITCH pages.
Press the FOOT SW. button in the DISPLAY SELECT section.
DISPLAY SELECT
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
The following display appears.
7
Footswitch-Left Page
DATA CONTROL
DATA CONTROL
Footswitches and Expression Pedal
<FOOT.SW>MODE:OFF
1
2
3
4
OFF
RHYTHM
GLIDE
TREM.
1 Off
Cancels Left Footswitch control.
97
2 Rhythms
Selection of Left Footswitch control over rhythm functions. When this is
chosen, the following items appear at the bottom of the display:
DATA CONTROL
DATA CONTROL
<FOOT.SW>MODE:RHYTHM
”STOP ’ENDING ’FILL
2 -1
2 -2
2 -3
2 -1
Stop
Functions as an on/off switch for the rhythm or the rhythm
sequence.
2 -2
Ending
Switches the rhythm to the Ending pattern, after which the rhythm is
stopped.
2 -3
Fill In
Switches the rhythm to the Fill In pattern.
3 Glide
Selection of Footswitch control over Glide.
Pressing the Footswitch immediately lowers the pitch of the selected voice
or voices by a half step. And releasing it slowly returns the pitch to the
original. When the Glide setting is chosen, the following display appears:
Also, page number will be shown at the top right side. The Glide function is
configured with three pages.
7
Footswitch – Glide Page 1
Footswitches and Expression Pedal
DATA CONTROL
DATA CONTROL
PAGE
DATA CONTROL
PAGE
DATA CONTROL
PAGE
<FOOT.SW>MODE:GLIDE⁄
”UPPER1
”UPPER2
3 -1
3 -1
Footswitch – Glide Page 2
DATA CONTROL
<FOOT.SW>MODE:GLIDE¤
’LOWER1
’LOWER2
3 -1
3 -1
Footswitch – Glide Page 3
DATA CONTROL
<FOOT.SW>MODE:GLIDE‹
”LEAD
TIME:2
3 -1
98
3 -2
3 -1
3 -2
Upper 1, 2, Lower 1, 2, Lead
The Glide function can be applied to any or all of the voice sections
shown in the display. Select the desired voice section(s).
Time
Determines the speed of the Glide function, or in other words, how
gradually the pitch returns when the Footswitch is released. Higher
settings produce slower pitch changes.
NOTE:
When the Glide function is applied, the
Vibrato is not effective.
Range: 1-5
4 Tremolo
Selection of Footswitch control over Tremolo.
Pressing the Footswitch turns the Tremolo effect on and off (Chorus),
performing the same function as the TREMOLO (FAST) button in the
DISPLAY SELECT section. (If you want to use this function, the tremolo
settings must be set properly. See page 42 for more information.)
DATA CONTROL
DATA CONTROL
<FOOT.SW>MODE:TREM.
7
Footswitches and Expression Pedal
99
2 Expression Pedal
You can choose the function of the Expression Pedal from three settings.
1
2
Press the PITCH/MIDI button in the DISPLAY SELECT section.
Transpose/Pitch function, the first page, will be displayed.
DISPLAY SELECT
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
Select page 3 using Page buttons at the right side of the LCD display.
MIDI IN page will be displayed.
DATA CONTROL
DATA CONTROL
<MIDI IN> LEAD:INT.‹
SYNC:INT. EXP.:AUTO
EXP. (Expression)
Determines the control of the expression pedal functions.
7
DATA CONTROL
DATA CONTROL
Footswitches and Expression Pedal
<MIDI IN> LEAD:INT.‹
SYNC:INT. EXP.:AUTO
AUTO
INT.
EXT.
Ordinarily, this control is set to Auto.
However, when it is set to INT., the expression pedal lets you control Electone
volume even during M.D.R. playback.
When set to EXT., another (external) Electone controls over the volume of the
Electone.
100
PAGE
8 Transpose and Pitch Controls
There are two pitch-related controls on the Electone: Transpose and Pitch. Transpose allows you to change the
key of the instrument and Pitch lets you finely adjust the tuning. These features make it easy to change the key
of a song to accommodate a vocalist’s range or to precisely match the tuning of another instrument.
1
Press the PITCH/MIDI button in the DISPLAY SELECT section.
Transpose/Pitch function, the first page, will be displayed.
DISPLAY SELECT
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
Transpose/Pitch Page
DATA CONTROL
DATA CONTROL
<TRANSPOSE><PITCH> ⁄
0
A=440.0Hz
1
2
1 Transpose
Determines the coarse pitch setting of all the voices, and is adjustable in half
steps (semitones).
Range: -6 - +6 (one octave)
2 Pitch
Determines the fine pitch setting of all the voices. The range is about a
quarter of semitone.
NOTE:
8
The default Pitch is 440.0Hz (=A3).
NOTE:
Range: 438.8Hz – 444.5Hz
Transpose and Pitch Controls
The pitch changes cannot be recorded to
the Music Disk Recorder.
About the Pitch
Each voice is tuned with the temperament.
Cent
LEAD voice
+6.0
LEAD
UK voice
+2.4
(UK voice 2)
+1.2
UK
NOTE:
When matching the pitch with other
instrument, use the Clarinet voice on the
Lower keyboard.
(UK2)
LK voice
0 (Standard 440Hz)
LK
(LK voice 2)
–1.2
(LK2)
PK voice
–3.6
PK
101
9 MIDI
MIDI (Musical Instrument Digital Interface) is a kind of communication system for electronic musical
instruments. It is built into most every modern digital musical instrument and allows different instruments to
“talk” to each other and control each other’s functions. For example, the Upper keyboard of your Electone
could be used to play sounds on a connected synthesizer. In another application, a rhythm machine can be
programmed to play its rhythms in perfect synchronization with the tempo set on the Electone.
To use the MIDI functions you must, of course, have a second MIDI device (such as a synthesizer or rhythm
machine), and a set of MIDI cables. For more information see page 105.
To select the MIDI page:
1
Press the PITCH/MIDI button in the DISPLAY SELECT section.
DISPLAY SELECT
VOICE
DISPLAY
EFFECT
SET
A.B.C.
M.O.C.
FOOT
SW.
REGIST.
SHIFT
PITCH
MIDI
TREMOLO
(FAST)
Transpose/Pitch function, the first page, will be displayed. The MIDI
related settings are shown on the second and third pages.
2
Select pages 2 and 3 using Page buttons at the right side of the LCD
display.
MIDI OUT Page
2
DATA CONTROL
DATA CONTROL
<MIDI OUT>LOWER: 2 ¤
UPPER: 1 PEDAL: 3
1
3
For setting the channels over which MIDI information will be transmitted. Any
channel from 1 through 16 can be assigned to each keyboard, the Upper
keyboard, the Lower keyboard and the Pedalboard. The note on/off messages
on each keyboard will be sent through the channels set here.
9
MIDI
1 Upper
Selects the transmit channel for Upper keyboard from channels 1 - 16.
2 Lower
Selects the transmit channel for Lower keyboard from channels 1 - 16.
3 Pedal
Selects the transmit channel for Pedalboard from channels 1 - 16.
The MIDI receive channel of each connected MIDI device should match the
numbers set here.
102
PAGE
Receive Channels
When using another MIDI device to play the Electone’s voices, you must
set the MIDI transmit channel(s) of the connected device to match the
receive channel(s) of the Electone.
The MIDI receive channels of the Electone are fixed to the following
values:
Upper Keyboard: 1
Lower Keyboard: 2
Pedalboard: 3
MIDI IN Page
1 -1
DATA CONTROL
DATA CONTROL
PAGE
<MIDI IN> LEAD:INT.‹
SYNC:INT. EXP.:AUTO
1 -2
1 Internal/External Controls
Switches between the Electone (INT.: Internal) and the connected device
(EXT.: External) to control the displayed items.
Lead
Determines Internal or External control of the Lead Voices. When
set to Internal, Lead Voices are played from the Electone and the
sounds from a connected MIDI instrument can be played via MIDI
channel 1 (or channel 2, when the To Lower function is on). When
set to External, the Lead Voices can only be played from the
connected instrument via MIDI channel 4.
1 -2
Sync.
Determines the source of the timing control, for rhythm
synchronization purposes. Setting this to Internal gives the Electone
timing control over the connected rhythm machine. This also allows
you to start and stop the rhythms of the connected rhythm machine
from the Electone’s panel controls. Setting this to External gives
timing control to the connected rhythm machine.
9
NOTE:
Accompaniment pattern sounds cannot be
controlled via MIDI.
MIDI
1 -1
NOTE:
For the information on EXP. See page 100.
103
10 Accessory Jacks and Controls
On the underside of the Electone keyboard is a separate panel equipped with various input/output terminals
and miscellaneous controls, the functions of which are described below.
5
2
HOST SELECT
TO HOST
4
PC-2
MIDI
1
HEADPHONES
R
AUX. L
OUT
PC-1
Mac
MIDI
OUT
IN
3
1 AUX. OUT (RCA, L/R)
This pair of RCA jacks is for connection to an external amplifier/speaker.
2 HEADPHONES (Phone)
For connection of a stereo headphone set. When headphones are connected
to this jack, sound to the Electone’s built-in speaker system is automatically
cut off, allowing you to play without disturbing others.
3 MIDI IN/OUT
For connecting external devices such as synthesizer and rhythm machine
with MIDI cables. MIDI cables are required (page 106).
4 TO HOST
This terminal can be connected to the serial port of a personal computer
instead of using MIDI connection.
5 HOST SELECT
When you have connected the Electone and the personal computer using the
TO HOST terminal, you need to select the appropriate setting here
depending on the computer used. (page 105)
10
Accessory Jacks and Controls
104
NOTE:
See next page for the details of the
connection using the TO HOST terminal.
11 Appendix
MIDI
On the right underside of the Electone keyboard you will find the MIDI IN/
OUT jacks and TO HOST terminal.
MIDI is an acronym that stands for Musical Instrument Digital Interface,
which allows electronic musical instruments to communicate with each
other, by sending and receiving MIDI messages. If your Electone is
connected with external devices via these MIDI jacks (with a personal
computer via the TO HOST terminal) and appropriate MIDI settings are
done, you can play an external MIDI device such as synthesizer from your
Electone keyboard or your Electone can be played by an external device
such as sequencer (by a personal computer with a sequencing software
installed).
You need MIDI cable(s) when you exchange the data between Electone and
an external device. Or you need a serial cable when you connect Electone’s
TO HOST to the computer serial port instead of using MIDI cables.
Also, to exchange the data between your Electone and connected MIDI
device you have to match the MIDI transmit/receive channels on both
devices. Receive channels of Electone are fixed as mentioned on page 103.
Accordingly, you need to match the transmit channels on the external
device to the fixed receive channels of Electone when you want to control
Electone by the external device. See page 102 for the detailed information
about the MIDI channel settings.
NOTE:
See page 107 for the information on the
MIDI message types.
Setting examples
Using the TO HOST terminal
Using a separately available Serial Cable allows you to directly connect them
(between the TO HOST terminal of your Electone and the Serial Port of the
personal computer). In this case you need to select one of the HOST SELECT
switches to match the computer type you use.
No additional MIDI setting is necessary.
NOTE:
MIDI jacks will be inactive when the TO
HOST terminal is currently used.
Windows 95/98/Me
NOTE:
HOST SELECT
PC-2
MIDI
8-pin MINI DIN to
D-SUB 9-pin Cable
PC-1
Mac
For Windows users: To actually exchange
the data via the Serial Cable you need to
install the appropriate MIDI driver to your
personal computer in advance.
TO
HOST
11
NOTE:
RS-232C
(DB9)
Windows 95/98/Me
EL-100
(Computer)
HOST SELECT
PC-2
MIDI
Macintosh Peripheral
Cable (M0197)
PC-1
Mac
Appendix
Macintosh
Select the HOST SELECT switches as follows:
When you use MIDI connection: MIDI
When you use TO HOST connection with
Windows system: PC-2
When you use TO HOST connection with
Macintosh: Mac
TO
HOST
NOTE:
If you use a PC with USB terminal, you
need to use USB interface.
EL-100
Macintosh
(Computer)
105
Using MIDI IN/OUT jacks
Controls an external device using
the EL-100 (as a master)
Controls the EL-100 using an external
device (as a slave)
Exchanges the data between EL-100 and
an external device
EL-100
EL-100
EL-100
MIDI OUT
MIDI IN
MIDI IN
HOST SELECT
PC-2
MIDI
PC-1
Mac
MIDI IN
MIDI OUT
HOST SELECT
PC-2
MIDI
HOST SELECT
PC-1
Mac
PC-2
MIDI
MIDI OUT
MIDI OUT
MUSIC SYNTHESIZER
REALTIME CONTROL
EXTENDED SYNTHESIS
PC-1
Mac
MIDI IN
MIDI
Interface
MU80 etc.
MIDI Keyboard
PC
1 Control an external device using the EL-100
Using an external MIDI keyboard or MIDI tone generator
● Playing your Electone can cause the MIDI keyboard (or tone generator) to
be played using its own voices, accomplishing thick sound layers. (The
MIDI receive channels of the MIDI keyboard must match the transmit
channels on your Electone.)
● Various messages including the values how far the expression pedal is
pressed down and how hard you play the Electone keyboard can be transmitted as digital data. However, how the external device responds depends on
the external device you have connected.
● The performance on your Electone can be recorded onto your PC using an
appropriate sequencing software. (You need a sequencing software in this
case.)
2 Control the EL-100 using an external device
Using an external MIDI keyboard
● Playing the external MIDI keyboard can cause your Electone to be played
using Electone’s voices. (The MIDI transmit channels of the MIDI keyboard
must match the (fixed) receive channels on your Electone. The channels 1, 2
and 3 for the Upper, Lower and pedal voices, respectively.)
● Also, Keyboard Percussion on your Electone can be played by playing the
external MIDI keyboard. (The MIDI transmit channels of the MIDI keyboard must be channel 15)
11
Appendix
● The MIDI data played back by the external PC (using a sequencing software) can be played using Electone’s voices. You can use the Electone as
an XG tone generator for computer-based music production. See page 110
for the details to use the EL-100 as an XG tone generator.
106
NOTE:
You cannot use the M.D.R. and MIDI
function at one time since the M.D.R. is
also connected via MIDI internally.
The MIDI Messages of the EL-100
The MIDI messages can be divided into two groups: the Channel Messages and
System Messages. The Channel Messages are the data related to the
performance on the keyboard for a specific channel. Each time you play the
keyboard on the EL-100, the channel messages, which keys are played and how
hard the keys are pressed, will be transmitted via a specific channel. The
System Messages are the data that allows several MIDI devices communicate
each other. Below is an explanation of the various types of MIDI messages
which the EL-100 can receive/transmit.
Channel Messages
Channel Messages are the data related to the performance on the keyboard for a
specific channel.
Key related messages
These are transmitted every time you play the keyboards on your Electone.
Reversely, the Electone can be played using these data from an external
keyboard.
Note On
Indicates which keys are played with the note numbers 0
through 127. The note range is C-2 (0) – G8 (127), C3=60.
Velocity
Indicates how hard the key is held. The range is 1 - 127.
Note Off
Generated when a key is released.
Program Change
The Program Change messages allow you to change voices in the middle of a
song. With these messages you can change the registrations of the EL-100.
NOTE:
For more detailed information see MIDI
Data Format on page 111 and MIDI
Implementation Chart on page 120.
NOTE:
For more detailed information see MIDI
Data Format on page 111 and MIDI
Implementation Chart on page 120.
Control Change
The Control Change Messages let you select a voice bank, control volume,
panning, modulation, portamento time, brightness and various other control
parameters, through specific Control Change numbers.
NOTE:
For more detailed information on the
Control Change messages available for the
EL-100 see MIDI Data Format on page
111 and MIDI Implementation Chart on
page 120.
11
Appendix
107
System Messages
System Exclusive Messages
System Exclusive messages are used to exchange the system and voice/
registration data. These allow you to execute bulk dump operation, sending and
receiving all the data of the EL-100 including registrations to and from an
external device. This is especially useful for you to build up the library of the
registration data in a device like a hard disk.
Examples of Exchanging the Data
Use the following examples to send (or receive) the registration data to (or
from) a personal computer (a sequencing software).
First, you need to connect your EL-100 with a personal computer (a
sequencing software) using a Serial Cable or a MIDI cable (page 105).
NOTE:
You also need a sequencing software,
which has been properly installed in the
personal computer, and which can send
and receive system exclusive messages.
Send the Registration Data
from the EL-100 to the Personal Computer (PC)
Preparation (Setting up registrations)
Set the Strings voice on the Upper Keyboard of the EL-100.
Press STRINGS button on the Upper Keyboard Voice section, and
select String 1 from the Strings Menu.
1
2
Store the registration to the Registration Memory button 1.
While holding down the M. button Press the Registration Memory
button 1.
Sending the Registration Data
Send the Request-to-Send all RAM message, “F0, 43, 70, 70, 10, F7”
(Hexadecimal), from the sequencing software (PC) to the EL-100.
3
Once the EL-100 receives the Request-to-Send all RAM message, the
EL-100 automatically sends all registration data in the all registration
numbers to your PC.
You can store the registration data in a file on your PC.
11
Appendix
108
NOTE:
Depending on the capacity of your
sequencing software, you may need to
divide the data into two and send them to
the PC separately. If you want to divide,
see page 114, “Data Code to Send” table.
For example,
by changing the message from
“F0,43,70,70,10,F7” (all data) to
“F0,43,70,70,17,F7,” the Electone will
send the Keyboard Percussion Assignment
data only.
Send the Registration Data
from your PC to the EL-100 and
Change the Registration Memory Buttons
Send the data stored in the PC back to your Electone. Also, select a
Registration Memory button and then play the upper keyboard using PC.
Receiving the Registration Data
Send the Request-to-Receive all RAM message, “F0, 43, 70, 70, 20,
F7” (Hexadecimal), from the sequencing software (PC) to the EL-100.
1
Once the EL-100 receives the Request-to-Receive all RAM message, it
automatically receives all registration data and relocates them to the all
registration numbers.
Selecting the Registration Memory Buttons
Sending the Program Change messages from the PC to your EL-100 makes it
possible to change the registration on the Electone.
2
Send the Program Change message, “CF, 00” (Hexadecimal) to the EL100.
Once the Program Change message is received, the EL-100
automatically turns the Registration Memory button 1 on.
Sending the Note-On Messages
Send the Note-On message, “90, 30, 7F” (Hexadecimal) to the EL-100.
3
EL-100 receives the note-on message and plays C2 key on the Upper
keyboard. It plays String voice you have set in the previous step.
Send the Note-Off message, “90, 30, 00” to the Electone.
All the above operations can also be done with the M.D.R. easily and
efficiently. However, using the PC/ hard disk allows you to build up a
large data library a single disk cannot deal with.
11
Appendix
109
Use the EL-100 as an XG Tone Generator
You can also use the EL-100 as an XG tone generator since the EL-100 is
compatible with the XG format. You can play back the commercially available
XG song data with the Electone’s M.D.R., and also play them using an external
sequencer (or sequencing software) and the internal XG tone generator.
The internal tone generator section of the EL-100 is normally set to EL Mode
for playing as an “Electone.”
Sending an appropriate system exclusive message from the sequencing software
(PC) to the EL-100 changes the mode to XG Mode, in which you can use the
Electone as an XG tone generator.
1
Send the XG System On message, “F0, 43, 1N*, 4C, 00, 00, 7E, 00,
F7” (Hexadecimal), from the sequencing software (PC) to the EL-100.
*N: Device Number (“0” for the EL-100)
Once the XG System On message is received, the internal tone
generator will be in the XG Mode allowing the EL-100 to receive all
the MIDI messages defined by the XG format such as NRPN and Bank
Select.
NOTE:
The M.D.R. lets you play back the
commercially available XG song
data and convert the Electone song
data to XG data. For more
information on XG song playback
and data conversion functions, see
page 86, 87.
NOTE:
When you create an XG song data
using a sequencing software, be
sure to insert the XG System On
message at the beginning of the
data. The internal tone generator
mode automatically changes to
XG when you start to play back
the data.
NOTE:
The internal tone generator mode
automatically changes to XG
when you play back commercially
available XG song data.
11
Appendix
110
MIDI Data Format
1. Channel Messages
1.1 EL Mode
Code (Hexadecimal)
Function
Transmit
Receive
8n,nn,00-7F
Note Off
˛
1ch
UK
Remarks
˛
2ch
LK
˛
3ch
˛
(4ch)*
LEAD
˛
5-14ch
XG
˛
15ch
Keyboard Percussion
PK
9n,nn,00
Note Off
(1ch)*
1ch
UK
9n,nn,01-7F
Note On
(2ch)*
2ch
LK
(3ch)*
3ch
˛
(4ch)*
LEAD
˛
5-14ch
XG
˛
15ch
Bank select
˛
5-14ch
XG
Bn,01,00-7F
Modulation
˛
5-14ch
XG
Bn,04,00-7F
2nd Expression
˛
16ch
˛
(4ch)*
LEAD
Bn,00,00-7F
PK (note on transmit velocity=50H)
Keyboard Percussion
Bn,20,00-7F
Control
Bn,05,00-7F
Portamento Time
˛
5-14ch
XG
Bn,06,00-7F
Data Entry
˛
5-14ch
XG
Bn,26,00-7F
Bn,07,00-7F
Volume
˛
5-14ch
XG
Bn,0A,00-7F
Pan
˛
5-14ch
XG
Bn,0B,00-7F
Expression
16ch
16ch
5-14ch
Control
XG
Bn,40,00-7F
Hold
˛
5-14ch
XG
Bn,41,00-7F
Portamento
˛
5-14ch
XG
Bn,42,00-7F
Sostenuto
˛
5-14ch
XG
Bn,43,00-7F
Soft Pedal
˛
5-14ch
XG
Bn,47,00-7F
Resonance
˛
5-14ch
XG
Bn,48,00-7F
Release Time
˛
5-14ch
XG
XG
Bn,49,00-7F
Attack Time
˛
5-14ch
Bn,4A,00-7F
Brightness
˛
5-14ch
XG
Bn,54,00-7F
Portamento Control
˛
5-14ch
XG
Bn,5B,00-7F
Reverb Send Level
˛
5-14ch
XG
Bn,5D,00-7F
Chorus Send Level
˛
5-14ch
XG
Bn,5E,00-7F
Variation Send Level
˛
5-14ch
XG
Bn,60,00-7F
Data Increment
˛
5-14ch
XG
Bn,61,00-7F
Data Decrement
˛
5-14ch
XG
˛
5-14ch
XG
˛
5-14ch
XG
Bn,62,00-7F
NRPN LSB
Bn,63,00-7F
NRPN MSB
Bn,64,00-7F
RPN LSB
Bn,65,00-7F
RPN MSB
All Sounds Off
Bn,79,00
Reset All Controllers
Bn,7B,00
All Note Off
Bn,7C,00
Omni Off
Bn,7D,00
Omni On
Bn,7E,00
Mono
Bn,7F,00
Poly
11
Appendix
Bn,78,00
111
Code (Hexadecimal)
Function
Cn,nn
Program Change
Transmit
Receive
˛
1ch
UK
Remarks
˛
2ch
LK
˛
3ch
PK
˛
5-14ch
XG
16ch
16ch
Dn,00-7F
After Touch
˛
5-14ch
Control
XG
En,00-7F,00-7F
Pitch Bend
˛
5-14ch
XG
* Can be changed in the MIDI settings.
1.2 XG Mode
Code (Hexadecimal)
Function
Transmit
Receive
8n,nn,00-7F
Note Off
˛
1-16ch
Remarks
9n,nn,00
Note Off
(1ch)
UK
9n,nn,01-7F
Note On
(2ch)*
LK
(3ch)*
PK (note on transmit velocity=50H)
1-16ch
Bn,00,00-7F
Bank select
˛
1-16ch
1-16ch
Bn,20,00-7F
Bn,01,00-7F
Modulation
˛
Bn,04,00-7F
2nd Expression
˛
˛
Control
˛
˛
LEAD
Bn,05,00-7F
Portamento Time
˛
1-16ch
Bn,06,00-7F
Data Entry
˛
1-16ch
Bn,26,00-7F
11
Appendix
112
Bn,07,00-7F
Volume
˛
1-16ch
Bn,0A,00-7F
Pan
˛
1-16ch
Bn,0B,00-7F
Expression
16ch
1-16ch
Bn,40,00-7F
Hold
˛
1-16ch
Bn,41,00-7F
Portamento
˛
1-16ch
Bn,42,00-7F
Sostenuto
˛
1-16ch
Bn,43,00-7F
Soft Pedal
˛
1-16ch
Bn,47,00-7F
Resonance
˛
1-16ch
Bn,48,00-7F
Release Time
˛
1-16ch
Bn,49,00-7F
Attack Time
˛
1-16ch
Bn,4A,00-7F
Brightness
˛
1-16ch
Bn,54,00-7F
Portamento Control
˛
1-16ch
Bn,5B,00-7F
Reverb Send Level
˛
1-16ch
Bn,5D,00-7F
Chorus Send Level
˛
1-16ch
Bn,5E,00-7F
Variation Send Level
˛
1-16ch
Bn,60,00-7F
Data Increment
˛
1-16ch
Bn,61,00-7F
Data Decrement
˛
1-16ch
˛
1-16ch
Bn,62,00-7F
NRPN LSB
Bn,63,00-7F
NRPN MSB
Bn,64,00-7F
RPN LSB
Bn,65,00-7F
RPN MSB
Control
Code (Hexadecimal)
Function
Bn,78,00
All Sounds Off
Bn,79,00
Reset All Controllers
Bn,7B,00
All Note Off
Bn,7C,00
Omni Off
Bn,7D,00
Omni On
Bn,7E,00
Mono
Bn,7F,00
Poly
Cn,00-7F
Program Change
Transmit
Receive
˛
1-16ch
16ch
Control
Remarks
1-16ch
Dn,00-7F
After Touch
˛
1-16ch
En,00-7F,00-7F
Pitch Bend
˛
1-16ch
Transmit
Receive
Ø
Ø*
* Can be changed in the MIDI settings.
2. Realtime Messages
Code (Hexadecimal)
Function
F8
Clock
FA
Start
Ø
Ø
FC
Stop
Ø
Ø
FE
Active Sensing
Ø
Ø
FF
Reset
˛
˛
Remarks
* Received only when in the Ext. mode
3. System Exclusive Messages
3.1 Format
Universal Realtime Messages
Code (Hexadecimal)
Message
F0,7F,7F,04,01,SS,TT,F7
XG Master Volume
XN
Transmit
Receive
˛
Ø
˛
Ø
Transmit
Receive
˛
Ø
˛
Ø
Transmit
Receive
Universal Non-Realtime Messages
Code (Hexadecimal)
Message
F0,7E,7F,09,01,F7
GM ON
XN
XG Native
Code (Hexadecimal)
Message
F0,43,1N,4C,AH,AM,AL,..data..,F7
XG Parameter Change
˛
Ø
F0,43,0N,4C,BH,BL,AH,AM,AL,..data..,cc,F7
XG Bulk Dump
˛
Ø
F0,43,1N,27,30,00,00,MM,LL,cc,F7
XG Master Tuning
˛
Ø
F0,43,1N,4C,00,00,7E,00,F7
XG System On
˛
Ø
Transmit
Receive
Electone/Single Keyboard Common Messages
Code (Hexadecimal)
Message
F0,43,73,01,02,F7
Request for Internal Synch. Mode
˛
Ø
Request for External Synch. Mode
˛
Ø
03
11
Appendix
113
Electone Exclusive
Code (Hexadecimal)
Message
F0,43,70,70,00,...(Data)...F7
Bulk Dump Data
78
ID
F0,43,70,ID,00,F7
Model ID Data
F0,43,70,70,nn(*1),F7
Request-to-Send Data
78
ID
Ø
Ø
Ø
˛
Ø
Ø
˛
˛
Ø
˛
Ø
˛
Ø
Ø
78
˛
Ø
ID
˛
Ø
Ø
Request-to-Receive Data
F0,43,70,70,30,F7
Request-to-Send Model ID data
˛
F0,43,70,70,38,7F,F7
Bulk Dump Acknowledge
˛
˛
Bulk Dump Unacknowledge
Ø
˛
00
F0,43,70,70,40,nn(*3),7F,F7
Switch On
Ø
Ø
Switch Off
Ø
Ø
F0,43,70,70,40,50,TL,TH,F7
Tempo
Ø
Ø
F0,43,70,78,41,cd,dd,F7(*4)
Panel Switch Events
Ø
Ø
F0,43,70,78,42,...(Data)...F7
Current Registration Data
Ø
Ø
F0,43,70,78,44...(Data)...(*5),F7
EL MIDI Parameters
Ø
Ø
F0,43,70,70,70,nn(*6),F7
External MDR
˛
Ø
F0,43,70,70,73,F7
EL ON
˛
Ø
F0,43,70,70,78,SC,NC,F7
Bar Signal
Ø
Ø
00
X : don't care
N : Device Number(“0” on EL-100)
ID=4C
*1 Data Codes to Send
nn
Data
10
All RAM
11
Registrations
12
14,15
Rhythm Sequences
User Patterns
16
User Voices
17
Keyboard Percussion Assignments
*2 Data Codes to Receive
nn
Data
20
All RAM
21
Registrations
22
24,25
Rhythm Sequences
User Patterns
26
User Voices
27
Keyboard Percussion Assignments
*3 Switches
Appendix
114
Receive
˛
˛
F0,43,70,70,nn(*2),F7
11
Transmit
nn
Switch
45
Left Footswitch
Transmit Receive
Ø
Ø
47
Knee Lever
˛
Ø
48
Fill In
Ø
Ø
4B
Intro./Ending
Ø
Ø
*4 Switch Codes
Selectors
Code
Switch
Transmit Tx Range
Receive Rx Range Remarks
02
UK Voice 1
Ø
[00-0D]
Ø
[00-0D]
03
LK Voice 1
Ø
[00-0D]
Ø
[00-0D]
Switch Number
Switch Number
04
UK Voice 2
Ø
[00-01]
Ø
[00-0D]
Switch Number
05
LK Voice 2
Ø
[00-01]
Ø
[00-0D]
Switch Number
06
LEAD Voice
Ø
[00-04]
Ø
[00-04]
Switch Number
07
Pedal Voice 1
Ø
[00-04]
Ø
[00-04]
Switch Number
08
Pedal Voice 2
Ø
[00-04]
Ø
[00-04]
Switch Number
0B
Rhythm
Ø
[00-0B]
Ø
[00-0B]
Switch Number
0F
Registration Memory
˛
Ø
[00-0F]
Volume
Code
Switch
Transmit Tx Range
Receive Rx Range Remarks
12
UK Voice 1
Ø
[00-7F]
Ø
[00-7F]
13
LK Voice 1
Ø
[00-7F]
Ø
[00-7F]
Volume Data 00:MAX,7F:MIN
Volume Data; 00:MAX,7F:MIN
14
UK Voice 2
Ø
[00-7F]
Ø
[00-7F]
Volume Data; 00:MAX,7F:MIN
15
LK Voice 2
Ø
[00-7F]
Ø
[00-7F]
Volume Data; 00:MAX,7F:MIN
16
LEAD Voice
Ø
[00-7F]
Ø
[00-7F]
Volume Data; 00:MAX,7F:MIN
17
Pedal Voice 1
Ø
[00-7F]
Ø
[00-7F]
Volume Data; 00:MAX,7F:MIN
18
Pedal Voice 2
Ø
[00-7F]
Ø
[00-7F]
Volume Data; 00:MAX,7F:MIN
1A
Rhythm
Ø
[00-7F]
Ø
[00-7F]
Volume Data; 00:MAX,7F:MIN
1B
Reverb
Ø
[00-7F]
Ø
[00-7F]
Depth Data; 00:MAX,7F:MIN
To Lower
Code
Switch
Transmit Tx Range
Receive Rx Range Remarks
36
LEAD Voice
Ø
[00-01]
Ø
[00-01]
00:OFF,01:ON
37
Pedal Voice 1
Ø
[00-01]
Ø
[00-01]
00:OFF,01:ON
38
Pedal Voice 2
Ø
[00-01]
Ø
[00-01]
00:OFF,01:ON
Sustain
Code
Switch
Transmit Tx Range
Receive Rx Range Remarks
50
Upper Keyboard
Ø
[00-01]
Ø
[00-01]
00:OFF,01:ON
51
Lower Keyboard
Ø
[00-01]
Ø
[00-01]
00:OFF,01:ON
52
Pedalboard
Ø
[00-01]
Ø
[00-01]
00:OFF,01:ON
Keyboard Percussion
Code
Switch
Transmit Tx Range
Receive Rx Range Remarks
5B
Lower Keyboard
Ø
[00-01]
Ø
[00-01]
00:OFF,01:ON
5C
Pedal Board
Ø
[00-01]
Ø
[00-01]
00:OFF,01:ON
Disable
Code
Switch
5F
Disable
Transmit Tx Range
Ø
[00-01]
Receive Rx Range Remarks
Ø
[00-01]
00:OFF,01:ON
Tremolo
Code
Switch
60
Tremolo
Transmit Tx Range
Ø
[00-01]
11
Receive Rx Range Remarks
Ø
[00-01]
00:SLOW,01:FAST
Code
Switch
Transmit Tx Range
Appendix
Rhythm Sequence
Receive Rx Range Remarks
61
Sequence 1
Ø
[00-01]
Ø
[00-01]
00:OFF,01:ON
62
Sequence 2
Ø
[00-01]
Ø
[00-01]
00:OFF,01:ON
63
Sequence 3
Ø
[00-01]
Ø
[00-01]
00:OFF,01:ON
64
Sequence 4
Ø
[00-01]
Ø
[00-01]
00:OFF,01:ON
115
*5 EL MIDI Parameters
Voice Section Parameters
Panel Voice Parameters
Address
00
00-04, 06, 07
00-0D
Parameter
Data
2
00-7F
Voice Assign Number H
Ø
[00-7F]
Ø
00-7F
Voice Assign Number L
Ø
[00-0F]
Ø
[00-7F]
˛
[00-0D]
Ø
[00-0D]
˛
[00-7F]
Ø
[00-7F]
Ø
[00-7F]
Ø
[00-7F]
Ø
[00]
Ø
[00][05-7F]
00
00-04, 06, 07
10
1
00-0D
Voice Selector Number
00
00-04, 06, 07
11
1
00-7F
Volume
Data
Transmit Tx Range Receive Rx Range Remarks
Size
00:MIN
[00-7F]
7F:MAX
00
00-04, 06, 07
12
1
00-7F
Reverb Send Level
00:MIN
7F:MAX
00
00
00-04, 06, 07
00-04, 06, 07
14
15
1
1
00-04
00-7F
Feet
Pan
00:Preset
01:16Feet
[01]
[01]
02:8Fee
[02]
[02]
03:4Feet
[03]
[03]
04:2Feet
[04]
00:Right
Ø
[0B]
[04]
Ø
[1D]
40:Center
7F:Left
00
00-04, 06, 07
16
1
00-7F
Initial Touch Sensitivity
00:MIN
[00-11]
[12-25]
[2B]
[26-31]
[40]
[32-4E]
[55]
[4F-5A]
[63]
[5B-6E]
[75]
[6F-7F]
Ø
[00-7F]
Ø
Ø
[00]
Ø
[00-7F]
7F:MAX
00
00-04, 06, 07
19
1
00-01
User Vibrato
00:PRESET
01:USER
00
00-04, 06, 07
1A
1
02-1A
Vibrato Delay
00:Short
[01]
[00]
[01-7F]
Ø
[02-1A]
Ø
[00-7F]
Ø
[00-54]
Ø
[00-7F]
Ø
[3C-6C]
Ø
[00-7F]
˛
[00]
Ø
7F:Long
00
00-04, 06, 07
1B
1
00-54
Vibrato Depth
00:MIN
7F:MAX
00
00-04, 06, 07
1C
1
3C-6C
Vibrato Speed
00:Slow
7F:Fast
00
04, 06, 07
1F
1
00-01
To Lower
00:OFF
01:ON
00
04
20
1
00-02
Slide
00:OFF
[01]
Ø
01:ON
00
04
21
1
02-7F
Slide Speed
00
04
22
1
00-24
Detune
[00]
[00]
[01-7F]
Ø
[01]
[00]
[01]
Ø
[02]
[02-7F]
Ø
[00-7F]
Ø
[00-24]
Ø
[00-7F]
˛
[00]
Ø
02:KneeControl
˛
02:Slow
Ø
7F:Fast
00:Normal
24:TuneUP
00
00-07
23
1
00-01
2nd Expression Pedal
00, 01, 04, 06, 07
00
00-04
00:OFF
01:ON
24
1
00-01
Glide
00:OFF
01:ON
11
Appendix
116
[01]
Ø
[00]
[01]
[00]
[01-7F]
Ø
[00]
[01-7F]
Effect Parameters (Voice Sections)
Address
00-01 00-04, 06, 07
3F
Size
Data
1
00-05
Parameter
Effect Select
Transmit Tx Range Receive Rx Range
Content
Ø
00:Preset
Ø
[00]
Remarks
[00][07-7F]
01:OFF
[01]
[01]
02:Tremolo
[02]
[02]
03:Symphonic
[03]
[03]
04:Delay
[04]
[04]
05:Flanger
[05]
[05]
06:Distortion
[06]
[06]
00-01 00-04, 06, 07
40-42
1
00-7F
Reverb
˛
[00-7F]
Ø
[00-7F]
00-01 00-04, 06, 07
48-4A
1
00-7F
Tremolo
˛
[00-7F]
Ø
[00-7F]
00-01 00-04, 06, 07
50
1
00-7F
Symphonic
Ø
[00-7F]
Ø
[00-7F]
00-01 00-04, 06, 07
58-5B
1,2
00-7F
Delay
Ø
[00-7F]
Ø
[00-7F]
00-01 00-04, 06, 07
60-62
1
00-7F
Flanger
Ø
[00-7F]
Ø
[00-7F]
00-01 00-04, 06, 07
68-69
1
00-7F
Distortion
Ø
[00-7F]
Ø
[00-7F]
Keyboard Parameters
Sustain Parameters
Size
Data
02
Address
00-02
00
1
00-01
Sustain On/Off
Parameter
02
00-02
01
1
00-0C
Length
Content
00:OFF
Transmit Tx Range Receive Rx Range
˛
[00]
Ø
[15-3D]
01:ON
00:Short
Ø
[01]
Remarks
[00]
[01-7F]
Ø
[00-7F]
0C:Long
Keyboard Percussion Parameters
Address
Parameter
Size
Data
02
01-02
10
1
00-01
Keyboard Percussion
02
01-02
11
1
00-08
Modes
Content
00:OFF
Transmit Tx Range Receive Rx Range
˛
01:ON
00:Preset
[00]
Ø
[01]
Ø
01-08:UserAssign1-8
[00]
Remarks
[00]
[01-7F]
Ø
[01-08]
[00]
[01-08]
Effect Parameters (Keyboard)
Address
Size
Data
Parameter
Content
Transmit Tx Range Receive Rx Range
02
00-02
40-42
1
Reverb
˛
[00-7F]
Ø
[00-7F]
02
00-02
48-4A
1
Tremolo
˛
[00-7F]
Ø
[00-7F]
02
00-02
50
1
Symphonic
˛
[00-7F]
Ø
[00-7F]
02
00-02
58-5B
1,2
Delay
˛
[00-7F]
Ø
[00-7F]
02
00-02
60-62
1
Flanger
˛
[00-7F]
Ø
[00-7F]
02
00-02
68-69
1
Distortion
˛
[00-7F]
Ø
[00-7F]
Remarks
Rhythm
Rhythm Parameters
Address
Transmit Tx Range Receive Rx Range
Size
Data
Parameter
03
00
00-0B
1
00-65
Pattern Assign Number
Pattern Numbers
Ø
[00-62]
Ø
[00-62]
03
00
10
1
00-0B
Pattern Select Number
Selector Switch Numbers
˛
[00-0B]
Ø
[00-0B]
03
00
11
1
00-7F
Volume
00:MIN
˛
[00-7F]
Ø
[00-7F]
Ø
[00-7F]
Ø
[00-7F]
Ø
[00]
Ø
[00]
Ø
[00-7F]
Ø
˛
[00]
Ø
Content
Remarks
67-98
7F:MAX
03
00
12
1
00-7F
Reverb Send Level
00:MIN
11
7F:MAX
00
14
1
00-01
Auto Variation
03
00
15
1
00-7F
Rhythm Balance
00:OFF
01:ON
00:Cymbal
[01]
[01-7F]
Appendix
03
[00-7F]
40:Center
7F:Drums
03
03
00
00
16
17
1
1
00-01
00-03
2nd Expression
00:OFF
Tempo Control
01:ON
Footswitch Rhythm Mode
00:OFF
[01]
Ø
[00]
[01-7F]
[00][04-7F]
[00]
Ø
[01]
01:RhythmStop
[01]
02:Ending
[02]
[02]
03:FillIn
[03]
[03]
117
Rhythm Sequence Parameters
Address
03
01
00-03
Size
Data
1
00-01
Parameter
Rhythm Sequence
Content
00:OFF
Transmit Tx Range Receive Rx Range
˛
01:ON
[00]
Ø
[01]
Remarks
[00]
[01-7F]
Accompaniment Parameters
Address
03
03
02
02
10
11
Size
Data
Parameter
1
00-03
Pattern Selector Number
1
00-01
Volume Mute
Content
00:Type1
Transmit Tx Range Receive Rx Range
Ø
02
12
1
00-7F
Volume
Ø
[01]
[01]
02:Type3
[02]
[02]
03:Type4
[03]
00:OFF
Ø
00:MIN
[00]
Remarks
[00]
01:Type2
[03]
Ø
[01]
01:MUTE
03
[00]
[00]
[01-7F]
Ø
[00-7F]
Ø
[00-7F]
Ø
[00-7F]
Ø
[00-7F]
7F:MAX
03
02
13
1
00-7F
Reverb Send Level
00:MIN
7F:MAX
A.B.C. Parameters
Address
03
03
03
03
00
01
Size
Data
1
00-03
1
00-01
Parameter
A.B.C. Mode
Lower Memory
Content
00:OFF
Transmit Tx Range Receive Rx Range
Ø
03
02
1
00-01
Pedal Memory
Ø
[01]
[01]
02:Fingerd
[02]
[02]
03:CustomABC
[03]
00:OFF
Ø
00:OFF
[00]
[03]
Ø
Ø
[00]
[00]
[01-7F]
[01]
Ø
[00]
[01-7F]
[01]
01:ON
Remarks
[00][04-7F]
01:SingleFinger
01:ON
03
[00]
M.O.C. Parameters
Address
03
03
04
04
00
01
Size
Data
1
00-03
1
00-01
Parameter
M.O.C. Mode
M.O.C. Knee Control
Content
00:OFF
Appendix
118
Ø
[00]
Ø
[00][04-7F]
01:Close2Note
[01]
[01]
02:Close3Note
[02]
[02]
03:PassBOpen
[03]
00:OFF
01:ON
11
Transmit Tx Range Receive Rx Range
˛
[03]
Ø
[00]
[01-7F]
Remarks
Overall
System Parameters
Size
Data
04
Address
00
00
1
00-01
Disable
Parameter
04
00
02
1
3A-46
Transpose
Transmit Tx Range Receive Rx Range
Content
00:OFF
˛
[00]
Ø
[3A]
01:ON
04
00
03
1
00-0B
2nd Expression Range
Ø
[01]
3A:KeyDown
40:Normal
[40]
46:KeyUp
[46]
01:100 ¢
Remarks
[00]
[01-7F]
Ø
[3A]
[40]
[46]
˛
[01-0C]
Ø
[01-0C]
Ø
[00]
Ø
[00][04-7F]
0C:1200 ¢
04
04
00
04
00
1
05
1
00-03
Footswitch Mode
3C-4F Pitch
00:OFF
01:Rhythm
[01]
[01]
02:Glide
[02]
[02]
03:Tremolo
[03]
3C:PitchDown
[03]
Ø
[3C-4F]
Ø
[3C-4F]
Ø
[04-1C]
Ø
[00-7F]
Ø
[34-4C]
Ø
[00-7F]
˛
[00]
˛
[00]
Ø
[00][02-7F]
40:Normal
4F:PitchUp
04
00
06
1
00-04
Glide Speed
01:Slow
05:Fast
04
00
07
1
34-4C
Manual Balance
34:Upper
40:Center
4C:Lower
04
00
09
1
00-01
L.I.T.
00:Mode1
01:Mode2
04
00
0A
1
00-01
Expression INT/EXT
[01]
˛
00:Internal
01:External
[00]
[01]
[01]
[01]
Effect Parameters (Overall)
Address
Size
Data
Parameter
Transmit Tx Range Receive Rx Range
Content
Ø
[00-7F]
Ø
[00-7F]
Tremolo
Ø
[00-7F]
Ø
[00-7F]
Symphonic
˛
[00-7F]
Ø
[00-7F]
Delay
˛
[00-7F]
Ø
[00-7F]
1
Flanger
˛
[00-7F]
Ø
[00-7F]
1
Distortion
˛
[00-7F]
Ø
[00-7F]
04
00
40-42
1
Reverb
04
00
48-4A
1
04
00
50
1
04
00
58-5B
1,2
04
00
60-62
04
00
68-69
Remarks
*6 External MDR
nn
Command
01
Play Start
Transmit Receive
˛
Ø
02
Play Stop
˛
Ø
03
Record Start
˛
Ø
04
Record Stop
˛
Ø
09
Rhythm Pointer Reset
˛
Ø
11
Appendix
119
MIDI Implementation Chart
Date:15. Nov. 2001
Version: 1.00
YAMAHA [Electone-EL mode] / Model: EL-100
Function
Transmit
Default
Changed
1, 2, 3, 16 *1
1-16
1-3, 5-16 *2
4
Mode
Default
Messages
Altered
Mode 3
˛
************************
Mode 3
˛
˛
0-127 *4
True Voice
36-96 *3
************************
Ø 9nH, v=1-127
Ø 9nH, v=0
Ø 9nH, v=1-127
Ø 9nH, v=0, 8nH
Transmit with EL-100:
fixed to 80.
˛
˛
˛
Ø *6
PK after touch with EL-100:
not transmit.
˛
Ø *6
˛
˛
Ø
˛
Ø *7
˛
˛
˛
˛
˛
˛
Ø *6
Ø *6
Ø *7
Ø *6
Ø *6, 7
Ø *6
Ø *6
Ø *6
Ø *6
Ø *6
Ø *6
Ø *9
************************
Ø *10
System Exclusive
Ø
Ø
System
Common
Song Position
Song Select
Tune
˛
˛
˛
˛
˛
˛
System
Real Time
Clock
Commands
Ø
Ø
Ø *8
Ø
Aux
Messages
Local ON/OFF
All Notes OFF
Active Sense
Reset
˛
˛
Ø
˛
˛
Ø (123-127) *6
Ø
˛
Note ON
Note OFF
Velocity
Key's
Ch's
After Touch
Pitch Bend
0, 32
1, 5, 7, 10
4
6, 38
11
96, 97
64-67
71-74
84, 91, 93, 94
98-99, 100-101
120, 121
Control Change
Program Change
Range
Appendix
Notes
Mode 1 : OMNI ON, POLY
Mode 3 : OMNI OFF, POLY
120
Remarks
Basic Channel
Note Number
11
Receive
*1
*2
*3
*4
*5
*6
*7
*8
*9
*10
Bank Select
2nd Expression Pedal
Data Entry
Expression Pedal
Data Entry SW
Sound Controller
NRPN, RPN
(FAH, FCH)
Ch 1: UK; Ch 2: LK; Ch 3: PK; Ch 16: Control
Ch 1: UK; Ch 2: LK; Ch 3: PK; Ch 4: LEAD 1; Chs 5 - 14: XG; Ch 15: Keyboard
UK: 48 - 96; LK: 36 - 84; PK: 36 - 55
UK, LK, PK, LEAD 1: 36 - 96; XG: 0 - 127; Keyboard Percussion: 3 - 127
UK: UK Horizontal Touch; LK: LK Horizontal Touch
XG only
Control only
External Mode only
Control: 0 - 15, 112 - 116
UK, LK, PK, Control: 0 - 15, 112 - 116; XG: 0 - 127
Mode 2 : OMNI ON, MONO
Mode 4 : OMNI OFF, MONO
Ø : YES
˛ : NO
Date:15. Nov. 2001
Version: 1.00
YAMAHA [Electone-XG mode] / Model: EL-100
Transmit *11
Function
Receive
Basic Channel
Default
Changed
1, 2, 3, 16
1-16
1-16
1-16
Mode
Default
Messages
Altered
Mode3
˛
************************
Mode 3
˛
˛
36-96
************************
0-127
True Voice
Ø 9nH, v=1-127
Ø 9nH, v=0
Ø 9nH, v=1-127
Ø 9nH, v=0, 8nH
˛
˛
˛
Ø
˛
Ø
˛
˛
˛
˛
Ø
˛
˛
˛
˛
˛
˛
Ø
Ø
˛
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø 0-15, 112-116
************************
Ø
System Exclusive
Ø
Ø
System
Common
Song Position
Song Select
Tune
˛
˛
˛
˛
˛
˛
System
Real Time
Clock
Commands
Ø
Ø
˛
˛
Aux
Messages
Local ON/OFF
All Notes OFF
Active Sense
Reset
˛
˛
Ø
˛
˛
Ø (123-127)
Ø
˛
Note Number
Note ON
Note OFF
Velocity
Key's
Ch's
After Touch
Pitch Bend
0, 32
1, 5, 7, 10
4
6, 38
11
96, 97
64-67
71-74
84, 91, 93, 94
98-99, 100-101
120, 121
Control Change
Program Change
Range
Mode 1 : OMNI ON, POLY
Mode 3 : OMNI OFF, POLY
Transmit with EL-100:
fixed to 80.
Bank Select
2nd Expression Pedal
Data Entry
Expression Pedal
Data Entry SW
Sound Controller
NRPN, RPN
11
Appendix
Notes
Remarks
*11 The same as the one in the EL Mode
Mode 2 : OMNI ON, MONO
Mode 4 : OMNI OFF, MONO
Ø : YES
˛ : NO
121
Troubleshooting
Problem
Possible Cause and Solution
GENERAL OPERATION
A cracking noise is sometimes heard.
Noise may be produced when either an electrical appliance is turned on or off,
or an electric power tool (such as drill) is used in the proximity of the Electone.
If this occurs, plug the Electone into an electrical outlet located as far as
possible from the device that seems to be the source of the problem.
Interference from radio, TV, or other sources occurs.
This is caused by the proximity of a high-power broadcasting station, an
amateur ham radio setup or a mobile phone.
Electone generates some noise.
A cell phone may be used in the proximity of Electone. Using a cell phone
beside the Electone may cause a noise. Turn off the power of the cell phone.
Radio or TV generates some noise.
Locating a radio or TV close to the Electone causes to produce a noise from it.
Relocate it farther from the Electone.
The sound of the Electone causes surrounding
objects to resonate.
Because the Electone is capable of producing powerful bass sounds, resonance
may be caused in surrounding objects, such as cabinets or glass windows.
To avoid this, relocate the objects or lower the Electone’s volume.
Some of the lamps in the DISPLAY SELECT
section do not light.
The lamp of TREMOLO (FAST) button is lit when turned on.
The others momentarily flash when the function is selected.
The sound is too small even when the volume is
set to its maximum.
● The Master Volume may be set around the minimum position. Turn it
clockwise.
● The Expression Pedal may not be pressed down. Press it down with your
toe.
The Electone panel does not function normally or
the content of the memorized data has changed.
This happens very rarely. Occasionally, power surges and spikes due to
electrical storms or other reasons may cause the Electone to malfunction and/or
alter the contents of memorized data. If this happens, turn the power off and
turn it back to on.
Pressing a certain panel button doesn’t open its
related LCD display.
When the Pattern Disk is inserted in the M.D.R., the LCD will
not change even if you press any buttons.
Eject the Disk and press the desired button again.
VOICES/RHYTHMS
11
Appendix
122
Switching voices causes the volume to change,
despite their having identical volume setting.
The volume of certain voices may seem lower than that of others. Adjust the
balance of the sound with the volume control within the appropriate Voice
Condition display.
The pitch seems to be higher on the Pedalboard and
lower on the Upper and Lower keyboards.
You may feel it especially when playing piano voice. The temperament for the
acoustic piano is tuned by listening to the overtones since the overtone
configuration of the acoustic piano is so complicated that the actual notes in the
higher and lower registers are difficult to be adjusted. On the contrary, the
Electone voices including piano voice are tuned by actual notes. Thus, the
tuning method itself in the higher and lower registers is different.
Some voices seems to contain crack or distorted noise.
You may feel it mainly with wind instrument voices. These are purposely built
in effects, which can faithfully reproduce the characteristics of each instrument.
You can enjoy more realistic sounds such as brass vibration and breath noise.
When too many keys are pressed, not all of
the notes sound.
Total polyphonic capacity (notes sounding for both Upper and Lower
Keyboards) is 10 notes. The notes exceeding this limit may not be produced.
Only a note will be produced when pressing two
keys or more on the Pedalboard and/or Lead voice.
The Lead and Pedal voices are designed to sound one note at a time. When you
simultaneously press two or more keys, only the highest note will sound.
Problem
Possible Cause and Solution
VOICES/RHYTHMS
The volume of Upper keyboard is louder than that
of Lower keyboard, or vice versa.
Manual Balance is wrongly set to the either side, Upper or Lower. Open the
Voice Display by pressing the VOICE DISPLAY button in the DISPLAY
SELECT section, and select page 2 to display the Manual Balance. Then
change the balance between Upper keyboard and Lower keyboard.
Pedalboard doesn’t sound, even when its volume is
properly set.
● One of the A.B.C. modes, Single Finger or Fingered Chord, is active. Set
the A.B.C. mode to off on A.B.C. page.
● The TO LOWER button in the Pedal Voice is turned on. Turn them off.
When keys on the Lower keyboard or pedalboard
are pressed, the sounds of percussion instruments
are also heard.
Keyboard Percussion function is set to on.
Turn the Keyboard Percussion off.
Even though a Dotted button’s rhythm has been
selected and started, the pattern does not sound.
Since the Dotted buttons contain User rhythms, no rhythm will sound if a
Pattern Disk pattern has not been saved to the selected Dotted button.
EFFECT
The Initial Touch function does not operate.
Initial Touch setting in the Voice Condition is not high enough to get the effect.
Adjust the Initial Touch setting using the Voice Condition display.
The Reverb effect does not operate, even when
Reverb parameters for the selected voice sections
are increased.
The Reverb setting of the targeted voice group is set to 0. Raise the Reverb
volume in the Voice Condition page 2 of the desired voice group.
The Tremolo effect cannot be heard, even when the
TREMOLO (FAST) button in the DISPLAY
SELECT section is on.
To get the Tremolo effect, you first need to select the Tremolo function in the
Voice Condition page 3 or Effect Set page.
ACCOMPANIMENT
The pitch in the Single Finger mode does not
change, even when pressing different keys of
the keyboard.
Single Finger mode will only produce notes when played within a fixed octave
interval on the Lower keyboard.
If notes with the same letter name are pressed outside of that range, the chords
that are sounded will share the same pitch.
While an intro./Ending pattern is automatically
playing, the Lower keyboard does not produce any
sound, even when the keys are played.
Since the Accompaniment chords play automatically one after another, the
Lower keyboard is designed not to produce any sound during the playback of
an Intro./Ending pattern.
The Accompaniment cannot be heard even when
an appropriate Accompaniment type is selected and
the rhythm has been started.
The Accompaniment volume is set to 0 as the default. Be sure to raise the
Accompaniment volume on the rhythm condition page.
The harmony notes of the Melody On Chord
function cannot be heard.
The Upper keyboard has been set to sound only Lead voices. Raise the volume
of Upper Keyboard voices (not Lead voice, in this case) high enough to get the
effect.
11
Appendix
123
Problem
Possible Cause and Solution
REGISTRATION MEMORY
Certain functions have not been memorized to
Registration Memory.
Some functions will not be memorized.
(See page 67 for more information.)
An error occurs and the registration data is not
recorded to M.D.R., when executing To Disk
operation.
Your operation may be wrong or the Write-protect tab of the floppy disk is set
to on.
A simple beep sound is produced when I press the
Basic Regist. Button.
When the contents of the SEQ buttons are different from Electone’s default
settings (you may have loaded the sequence data from the upper models),
pressing one of the Basic Regist. buttons restores the original data and give a
simple beep sound to notify it.
MUSIC DISK RECORDER
11
Appendix
124
Recording or playback cannot be performed.
The PLAY or RECORD section buttons for selecting parts may be turned off.
Turn on the appropriate PLAY or RECORD buttons.
A total of 40 songs cannot be recorded.
If some song numbers contain a large amount of recorded data, the disk may
not have enough available memory left to record the normal maximum of 40
songs. Check the remaining memory.
Recording is stopped before the performance is
finished, or the Song Copy function cannot be
executed.
● The amount of recorded data on the disk is close to the maximum limit.
Either use another disk or delete the data of any unnecessary song number.
● The length of a subsequently recorded part cannot exceed the length of the
previously recorded parts. If you want to change the song length, first
delete the existing song and record again.
The rhythm does not start at the beginning of a
recording, or stops in the middle of the performance.
The M.D.R. is designed so that the rhythm cannot be started at the very
beginning of a recording. If you wish to use the rhythm, start it after the
available memory display appears on the M.D.R. display.
The notes of the recording are “stuck” and sound
continuously.
During playback, you removed the disk by pressing the EJECT button.
Whenever you wish to stop playback, always press the STOP button.
YAMAHA Electone
EL-100 ASSEMBLY INSTRUCTIONS
Carefully read these instructions BEFORE assembling the Electone.
■ Precautions
Be careful not to confuse parts, and be sure to install all parts in the correct direction by following the procedures given
below.
Be sure to assemble the Electone with two or more people.
Don’t use the screws other than the ones specified and included in this package. Use of incorrect screws can cause
damage and malfunction.
Be sure to tighten up all screws upon completing assembly.
To disassemble, reverse the procedures.
You need a Phillips (+) screwdriver to assemble the Electone.
the package, take out two cardboard pads from the both sides of the package, and place the main unit on
1. Open
top of the cardboard pads.
Position the pads not to directly contact the terminals equipped on the bottom of the main unit.
out all parts from the package.
2. Take
Please confirm that all parts shown in the illustration are provided.
Dust Cover
Music
Stand
AC Power Cord
1 Long/Black Screws (ø6X25mm): 4pcs.
Main Unit
2 Long/Yellow Screws (ø5X25mm): 4pcs.
Sideboard
(Left)
3 Short/Black Screws (ø5X12mm): 8pcs.
Speaker
Unit
Grill Net
(Attached to the Speaker Unit)
Pedalboard Cord Cramps: 2pcs.
11
Screw caps: 4pcs.
Bench
Pedalboard Unit
Appendix
Sideboard
(Right)
Bench Board
Legs: 4pcs.
125
the Sideboards onto the Pedalboard unit.
3. Mount
Be sure not to confuse the Right and Left Sideboards.
3-1
Raise the Pedalboard as shown in the illustration
below.
3-2
Position each screw hole on both the Pedalboard and
Sideboards as shown in the illustration and mount
the Sideboards onto the Pedalboard using the 4 Short/
black screws (2 screws on each Sideboard).
4-2
While holding the Sideboard(s) to the Speaker unit, screw
the 4 Short/black screws, from the rear side, to fasten it
to the Sideboards. Cover 4 screw holes on the rear
side with the 4 screw caps.
4-3
Also, use the 4 Long/yellow screws to secure it.
while pushing
the Sideboard
toward the
Speaker unit...
2 Long/yellow screws
while pushing
the Sideboard
toward the
Speaker unit...
while pushing the
Sideboard toward
the Pedalboard…
3 Short/black screws
3 Short/black
screws
Screw caps
Screw caps
3 Short/black screws
3-3
Stand the Pedalboard after securing the screws.
4. Mount the Speaker Unit onto the Sideboards.
4-1
Remove the Grill Net from the Speaker Unit.
4-2
Hold the Speaker unit horizontally (by 2 people) and
slide it, from the rear side, in place along the brackets.
5. Mount the Main Unit.
5-1
As shown in the illustration, hold the Main unit
horizontally (by 2 people), and place it on the rear
side of the Speaker unit, then slide it to the front side.
Hook the guide screw,
protruding from the
bottom of the Main
unit, here.
11
Appendix
Make sure to center the main unit to produce equal
clearance on the left and right sides.
Take care not to drop the Main unit or to pinch your
finger(s) between the Speaker unit and Main unit.
Take care not to drop the Speaker unit or to pinch your
finger(s) between the Speaker unit and Sideboard.
126
5-2
Use the 4 Long/black screws to fasten the Main unit
to the Sideboards as shown in the illustration.
the Pedalboard cord and Speaker cord
7. Connect
to the Main Unit.
Make sure that the latches on each plug of the cords
face to your side and that you connect them to each
socket securely.
1 Long/black
screws
Speaker
cord
Pedalboard
cord
the Pedalboard cord to the Sideboard using
8. Fix
the Pedalboard cord Cramps.
8-1
Stick the 2 Pedalboard cord cramps to the rear side of
the Left Sideboard as shown in the illustration.
8-2
Fix the Pedalboard cord in the cramps.
1 Long/black
screws
Grill Net onto the Speaker.
6. FitFirst,thealign
the bottom line and then fix it.
Hook up the Grill Net by
inserting the protrudents
into the holes.
11
Shut the cramp
after inserting
the cord.
Appendix
127
the AC Power Cord plug to the AC Inlet
9. Connect
of the Main Unit.
BENCH ASSEMBLY
Reverse the bench board and place one of the legs to the
corner of the bench board, then tighten the nut using the
included wrench. Be sure to put the washer between the
leg and the bench board.
leg
washer
bench
board
nut
10.Place the Music Stand.
■ After completing the assembly, please check the following
items.
•
Are there any parts left over?
fi Review all assembly procedures.
•
Is the Electone clear of doors and other movable
fixtures?
fi Move the Electone to an appropriate location.
•
Does the Electone make a rattling noise when you
shake it?
fi Tighten all screws.
•
Can the Electone be turned on?
fi Confirm that the AC power cord plug is securely
connected to the Electone’s AC Inlet and the other
side of the cord is connected to an appropriate power
outlet.
•
Does the Electone produce sounds?
fi Confirm that the Speaker cord plug and the Pedalboard
cord plug are securely connected to each socket on
the Main unit.
11.
Turn on the Electone’s power switch and confirm
that the Electone can be played, or that the
assembly is successful.
11
Appendix
If the Electone creaks or is otherwise unsteady when you
play on the keyboard, refer to the assembly instructions and
tighten all screws again.
128
EL-100 Specifications
KEYBOARD
Upper: 49 keys (C – C), Lower: 49 keys (C – C), Pedal: 20 keys (C – G)
Initial Touch
Upper 1, 2, Lead, Lower 1, 2, Pedal 1, 2 (Available only when it is played by external MIDI control)
VOICE
Tone Generation
AWM
Upper Keyboard Voice
Strings 1, 2, 3, 4, 5, 6, 7, Pizz. Strings, Tremolo Strings, Synth. Strings 1, 2, 3; Brass 1, 2, 3, 4, 5,
Lower Keyboard Voice
Synth. Brass 1, 2, 3; Clarinet 1, 2, Bass Clarinet, Synth. Clarinet 1, 2; Saxophone 1, 2,
Upper Keyboard Voice 2
Soprano Sax., Sax. Ensemble 1, 2, Synth. Sax, Synth. Lead 1, 2, 3, 4, 5; Chorus 1, 2, 3, 4, 5,
Lower Keyboard Voice 2
Vocal; Organ 1, 2, 3, 4, Jazz Organ 1, 2, 3, 4, Pop Organ 1, 2, Theatre Organ 1, 2, Accordion,
Bandoneon; Piano 1, 2, Honky Tonk, Elec. Piano 1, 2, 3, Harpsichord, Clavi., Clavichord;
Guitar 1, 2, 3, 12 String Guitar, Banjo, Mandolin, Sitar, Shamisen, Elec. Guitar 1, 2,
Muted Guitar, Distortion Guitar, Harp, Steel Guitar, Koto, Taisho Koto; Vibraphone,
Glockenspiel, Celesta, Music Box, Marimba, Xylophone, Chime, Synth. Chime, Steel Drum;
Cosmic 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16; Tutti 1, 2, 3, 4, 5, 6, 7;
[Upper] Harmonica 1, 2; [Lower] Horn 1, 2, 3, 4, Muted Horn; 2 Dotted Buttons;
[Upper] 115 Voices; [Lower] 118 Voices; Volume Fine
Lead Voice
Violin 1, 2, 3, 4, 5, Pizz. Violin, Cello, Kokyu; Flute 1, 2, Piccolo, Yokobue, Recorder, Ocarina,
Pan Flute, Shakuhachi, Whistle; Oboe 1, 2, English Horn, Bassoon 1, 2;
Trumpet 1, 2, 3, 4, 5, 6, Muted Trumpet, Trombone 1, 2, Muted Trombone, Flugel Horn,
Euphonium; To Lower; Dotted Button; 34 Voices; Volume Fine
EFFECT/
CONDITION
Pedalboard Voice
Contrabass 1, 2, 3, Pizz. Bass, Upright Bass; Elec. Bass 1, 2, 3, 4, Synth. Bass 1, 2, 3; Organ
Pedalboard Voice 2
Bass 1, 2, 3, 4; Tuba, Timpani, Timpani Roll; To Lower; Dotted Button; 19 Voices; Volume Fine
Voice Display
Upper 1, 2; Lower 1, 2; Lead; Pedal 1, 2; Manual Balance
Digital Reverb
3 Types: Room, Hall, Church; Length; Depth; Volume: Upper 1, 2, Lower 1, 2, Lead,
Pedal 1, 2, Accompaniment, Percussion
Sustain
Upper, Lower, Pedal: Length
Tremolo/Chorus
Upper 1, 2, Lower 1, 2, Lead, Pedal 1, 2, Tremolo (Fast): Speed; Chorus: Slow, Stop
Symphonic/Celeste
Upper 1, 2, Lower 1, 2, Lead, Pedal 1, 2; Mode: Symphonic/Celeste
Vibrato
Upper 1, 2, Lower 1, 2, Lead, Pedal 1, 2: Preset/User (Delay, Depth, Speed)
Delay
Upper 1, 2, Lower 1, 2, Lead, Pedal 1, 2; Control: Time, Feedback, Balance; Mode: Mono,
Stereo 1, 2, 3
Flanger
Upper 1, 2, Lower 1, 2, Lead, Pedal 1, 2; Control: Speed, Feedback, Depth
Distortion
Upper 1, 2, Lower 1, 2, Lead, Pedal 1, 2; Control: Level, Hi-pass
Glide
Upper 1, 2, Lower 1, 2, Lead; Control: Time
Lead Slide
On/Off; Control: Time
Lead Tune
Tune Control
Panning
Upper 1, 2, Lower 1, 2, Lead, Pedal 1, 2; (7 positions)
Feet
Upper 1, 2, Lower 1, 2, Lead, Pedal 1, 2; Preset 2' (Pedal Voices only)/4'/8'/16'
11
Appendix
129
RHYTHM
Rhythms
March 1, 2, 3, Polka 1, 2, Country 1, 2, Broadway, Baroque; Waltz 1, 2, 3, 4, 5,
Jazz Waltz 1, 2, 3, Bolero; Swing 1, 2, 3, 4, 5, 6, Jazz Ballad, Dixieland 1, 2; Bounce 1, 2, 3,
Reggae 1, 2; Slow Rock 1, 2, 3; Tango 1, 2, 3; Chacha, Rhumba, Beguine; Mambo, Salsa,
Samba 1, 2, 3, Bossanova 1, 2, 3; 8Beat 1, 2, 3, 4, 5, Dance Pop 1, 2, 3, 4; 16Beat 1, 2, 3, 4, 5,
Funk 1, 2, 3; User 1-8 (A-D); 2 Dotted Buttons; 66 Rhythms; Volume Fine
Variations
Fill-In; Intro. Ending; Lead In; Auto Variation: On/Off
Others
Start; Synchro Start; Tempo; Bar/Beat LED; Condition: Reverb, Balance, Volume
Rhythm Sequence
On/Off, Sequence 1 - 4
KEYBOARD PERCUSSION
Lower, Pedal On/Off: Lower Preset, Pedal Preset, User 1- 8; Copy: LK Preset, PK Preset,
User; Assign: 120 Instruments, Clear
ACCOMPANIMENT
Auto Bass Chord
Mode: Off; Single Finger; Fingered Chord; Custom A.B.C.; Memory: Lower, Pedal
Accompaniments
Type 1, 2, 3, 4, All Off, Volume, Reverb
MELODY ON CHORD
Mode: Off, 1, 2, 3
BASIC REGISTRATION
1-5
REGISTRATION MEMORY
M./To Disk, 1 - 8; Disable Button; Registration shift
MUSIC DISK RECORDER
Play/Record: Upper, Lower, Pedal, Lead, Keyboard Percussion, Control; Pause, Stop, Fast Forward/
Reverse, Song Select, Shift, Custom Play, Tempo; Format, Read & Auto Increment, Song Repeat; Song
Delete; Song Copy: From/To; Disk Copy, Punch in Recording, XG Song Playback, XG Easy Converter,
Song Name, Pattern Disk, Remaining Memory; LED Display; Eject
FOOT SWITCH
Left
Mode: Off; Rhythm (Stop, Ending, Fill-In); Glide (Upper 1, 2/Lower 1, 2/Lead; Time);
Tremolo/Chorus
Right
Regist. Shift Mode: Off, Shift, Jump, User (80 Positions; Cursor Controls: Data: Insert, Delete;
Shift End: Stop, Top, Next Song)
TRANSPOSE/PITCH
Transpose: -6 - +6; Pitch: 438.8Hz - 444.5Hz
LCD DISPLAY
20 x 2 Character
LANGUAGE
English, Japanese
OTHER CONTROLS
Power On/Off; Exp. Pedal (Right/Left Footswitches); Pitch Control; Transpose; Master Volume;
Display Select; Data Controls; Page; MIDI (Output: Upper, Lower, Pedal; Int./Ext.: Lead, Sync.,
Exp.)
OTHER FITTINGS
Dust Cover; Music Stand; Bench; Headphone Jack; Aux In/Out (RCA; R/L); MIDI In/Out; To Host;
Host Select
OPTIONAL ACCESSORIES
Pattern Disk; HPE-170 Headphones; 3.5" Floppy Disks
SOUND SYSTEM
Power Amplifiers
40W (Stereo)
Speakers
16cm x 2; 5cm x 2
DIMENSIONS (W x D x H)
112.3cm x 48.2cm x 92.5cm (111.1cm with Music Stand)
[Bench] 59.5cm x 29.5cm x 58.0cm
WEIGHT
55.0kg
[Bench] 6.2kg
Specifications and description in this Owner's Manual are information purposes only.
Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice.
As specifications, equipment or options may not be the same in every locale, please check with Yamaha dealer.
11
Appendix
130
Index
A
F
A.B.C. ............................................................ 52
A.B.C./M.O.C. .......................................... 52, 64
ACC. Reverb ................................................. 55
Accompaniment ...................................... 45, 54
Auto Bass Chord (A.B.C.) ............................. 52
Auto Varietion (Rhythm) ................................ 48
AUX. OUT .................................................... 104
Fast Forward (M.D.R.) ...................................
Fast Reverse (M.D.R.) ...................................
Feedback (Delay) .........................................
Feedback(Flanger) .......................................
Feet ................................................................
Fill In ..............................................................
Fingered Chord .............................................
Flanger ..................................................... 32,
Floppy Disk ....................................................
FOOT SW. ......................................................
FORMAT ........................................................
B
Balance (Delay) .............................................
Balance (Rhythm) .........................................
BAR/BEAT .....................................................
BASIC REGlST. .............................................
37
48
47
11
G
Glide (Footswitch) ......................................... 98
Group (Keyboard Percussion) ...................... 59
C
Celeste ........................................................... 35
Characteristics of Each Delay Type ............. 37
Chord ............................................................. 53
Chorus ..................................................... 35, 42
Church (Reverb) ............................................ 40
Clear (Keyboard Percussion) ....................... 59
Control data ................................................... 78
Copy/LK PRESET (Keyboard Percussion) ... 62
Copy/PK PRESET (Keyboard Percussion) ... 63
Copy/USER (Keyboard Percussion) ............. 63
Copy Protect ................................................. 95
Cursor Controls (Registration Shift) .............. 71
Custom A.B.C. ............................................... 52
CUSTOM PLAY .............................................. 88
D
D. (Disable) ...................................................
DATA CONTROL ...........................................
Data Controls (Registration Shift) .................
Delay (Effect) ........................................... 32,
Delay (Vibrato) ..............................................
Delete (Registration Shift) .............................
Depth (Flanger) .............................................
Depth (Reverb) ..............................................
Depth (Vibrato) ..............................................
Disk Copy ......................................................
DISPLAY SELECT ...................................... 9,
Distortion ................................................. 32,
Dotted button (Rhythm) ................................
Dotted button (Voice) ....................................
M
88
88
36
38
30
47
52
38
73
97
75
H
Hall (Reverb) ................................................. 40
HEADPHONES ............................................ 104
“hidden” voices ............................................. 27
Hi Pass (Distortion) ....................................... 39
HOST SELECT ............................................. 104
I
Initial Touch ................................................... 30
Insert .............................................................. 72
Instrument Names (Keyboard Percussion) .. 59
Internal/External (MIDI IN) .......................... 103
INTRO. ENDING ............................................ 46
J
68
14
72
36
33
72
38
40
33
92
20
39
49
21
E
K
KEYBOARD PERCUSSION ........................... 56
L
Language ...................................................... 16
LCD Display .................................................. 13
LEAD (MIDI) ................................................ 103
LEAD IN ......................................................... 46
LEAD VOlCE .................................................. 17
LED Display ................................................... 75
Left Footswitch .............................................. 97
Length (Reverb) ............................................ 40
Level (Distortion) ........................................... 39
Lower (MIDI OUT) ....................................... 102
LOWER KEYBOARD VOlCE .......................... 17
LOWER KEYBOARD VOlCE 2 ...................... 18
N
Next Song (Shift End) ................................... 71
P
PAGE ............................................................. 14
Panning .......................................................... 31
PART (XG) ..................................................... 86
Pattern Disk ................................................... 94
PAUSE (M.D.R.) ............................................ 88
Pedal (MIDI OUT) ........................................ 102
PEDAL VOICE ............................................... 17
PEDAL VOICE 2 ............................................ 18
Performance data ......................................... 78
Pitch ............................................................. 101
PITCH/MIDI .......................................... 101, 102
PLAY .............................................................. 76
Playback (M.D.R.) ......................................... 84
POSITION (Registration Shift) ...................... 71
POWER .......................................................... 10
Preset (Effect) ................................................ 32
Preset (Keyboard Percussion) ...................... 56
Preset (Vibrato) ............................................. 33
Preset Keyboard Percussion ........................ 57
PRESET/USER (Vibrato) ................................ 33
Punch-in Recording ...................................... 81
R
Read and Auto Increment (M.D.R.) ..............
RECORD ........................................................
Recording Registrations ...............................
Registration data ...........................................
Registration Memory .....................................
REGlST. SHlFT ..............................................
Remaining Memory (M.D.R.) ........................
Repeat playback ...........................................
Retry ..............................................................
REVERB .........................................................
Reverb (Rhythm) ...........................................
Reverb (Voice Condition) ........................ 31,
RHYTHM ........................................................
Rhythm (Footswitch) .....................................
Rhythm Condition ..........................................
Rhythm Menu ................................................
Rhythm Sequence .........................................
Right Footswitch ............................................
Room (Reverb) ..............................................
88
76
82
78
67
69
94
85
77
40
48
40
45
98
48
51
66
69
40
11
Appendix
Effect ........................................................ 29, 32
EFFECT SET .................................................. 34
Eject ............................................................... 73
ENDlNG ......................................................... 46
EXP. (Expression) ....................................... 100
Expression Pedal .................................. 11, 100
Jump (Registration Shift) .............................. 70
M./TO DISK .................................................... 67
M.BAL ............................................................ 20
MASTER VOLUME ........................................ 11
Melody On Chord (M.O.C.) ........................... 64
Memory (Lower/Pedal) .................................. 53
Metronome .................................................... 66
MIDI ..................................................... 102, 105
MIDI IN ......................................................... 103
MIDI IN/OUT ................................................ 104
MIDI OUT ..................................................... 102
Mode (Chorus) .............................................. 44
Mode (Delay) ................................................. 37
Mode (M.O.C.) .............................................. 65
Music Disk Recorder (M.D.R.) ...................... 73
Mute (XG) ...................................................... 86
131
S
V
Selecting Voice Group .................................. 35
SEQ. ............................................................... 66
Set (Keyboard Percussion) ........................... 59
SHIFT ............................................................. 75
Shift (Registration Shift) ................................ 70
Shift End ........................................................ 71
Single Finger ................................................. 52
Slide ............................................................... 34
Slide Time ...................................................... 34
SOLO (XG) .................................................... 86
Song Copy ..................................................... 90
Song Delete ................................................... 92
SONG REPEAT .............................................. 85
SONG SELECT .............................................. 75
SPEED (Flanger) ........................................... 38
SPEED (Tremolo) ........................................... 44
SPEED (Vibrato) ............................................ 33
START ............................................................ 46
STOP (Footswitch) ........................................ 98
STOP (M.D.R.) ............................................... 77
STOP (Shift End) ........................................... 71
Sustain ........................................................... 41
Symphonic ............................................... 32, 35
SYNC.(MIDI IN) ........................................... 103
SYNCHRO START ......................................... 46
Vibrato ...........................................................
Voice ..............................................................
Voice Condition .............................................
Voice Control .................................................
VOICE DISPLAY ...................................... 17,
Voice Menu .............................................. 18,
Voice section .................................................
Volume (Rhythm) ...........................................
Volume (Voice Condition) .............................
Volume (XG) ..................................................
Volume (Accompaniment) ............................
Volume balance ............................................
T
TEMPO ........................................................... 47
Tempo (M.D.R.) ............................................. 89
Time (Delay) .................................................. 36
TO HOST ..................................................... 104
TO LOWER .................................................... 21
Top (Shift End) .............................................. 71
Transpose .................................................... 101
Tremolo (Effect) ................................. 32, 35, 42
TREMOLO (FAST) ......................................... 44
Tremolo (Footswitch) ..................................... 99
Tune ............................................................... 34
Type (Accompaniment) ................................ 55
Type (Reverb) ............................................... 40
U
Upper (MIDI OUT) ....................................... 102
UPPER KEYBOARD VOlCE ........................... 17
UPPER KEYBOARD VOlCE 2 ....................... 18
User (Registration Shift) ................................ 71
User Keyboard Percussion ........................... 58
User rhythm ................................................... 50
User voice (Voice) ......................................... 22
11
Appendix
132
33
17
30
29
20
23
17
48
31
86
55
20
W
Write-protect tab ........................................... 74
X
XG .............................................................. 4, 86
XG Easy Converter ........................................ 87
XG Song Playback ........................................ 86
11
Appendix
133
11
Appendix
134
For details of products, please contact your nearest Yamaha or the authorized distributor listed below.
CENTRAL & SOUTH AMERICA
MEXICO
ASIA
HONG KONG
Yamaha de Mexico S.A. De C.V.,
Departamento de ventas
Javier Rojo Gomez No.1149, Col. Gpe Del
Moral, Deleg. Iztapalapa, 09300 Mexico, D.F.
Tel: 686-00-33
BRAZIL
Yamaha Musical do Brasil LTDA.
Av. Reboucas 2636, Sao Paulo, Brasil
Tel: 011-853-1377
ARGENTINA
Yamaha de Panamá S.A.
Sucursal de Argentina
Viamonte 1145 Piso2-B 1053,
Buenos Aires, Argentina
Tel: 1-4371-7021
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha de Panamá S.A.
Torre Banco General, Piso 7, Urbanizacion
Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
Tel: 507-269-5311
AFRICA
Yamaha Corporation,
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: 053-460-2312
MIDDLE EAST
* Except Turky and Cyprus
Yamaha Music Gulf FZE
LB21-128 Jebel Ali Freezone
P.O.Box 17328, Dubai, U.A.E.
Tel: 971-4-881-5868
Tom Lee Music Co., Ltd.
11/F., Silvercord Tower 1, 30 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel: 2737-7688
INDONESIA
PT. Yamaha Music Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 21-520-2577
KOREA
Yamaha Music Korea Ltd.
Tong-Yang Securities Bldg. 16F
23-8 Yoido-dong, Youngdungpo-ku, Seoul, Korea
Tel: 02-3770-0661
MALAYSIA
Yamaha Music Malaysia, Sdn., Bhd.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: 3-703-0900
PHILIPPINES
Yupangco Music Corporation
339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,
Makati, Metro Manila, Philippines
Tel: 819-7551
SINGAPORE
Yamaha Music Asia Pte., Ltd.
11 Ubi Road #06-00, Meiban Industrial Building,
Singapore
Tel: 65-747-4374
TAIWAN
Yamaha KHS Music Co., Ltd.
10F, 150, Tun-Hwa Northroad,
Taipei, Taiwan, R.O.C.
Tel: 02-2713-8999
THAILAND
Siam Music Yamaha Co., Ltd.
121/60-61 RS Tower 17th Floor,
Ratchadaphisek RD., Dindaeng,
Bangkok 10320, Thailand
Tel: 02-641-2951
THE PEOPLE'S REPUBLIC OF CHINA
AND OTHER ASIAN COUNTRIES
Yamaha Corporation,
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: 053-460-2317
HEAD OFFICE
Yamaha Corporation, Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: 053-460-2317
[EL] 23
Yamaha Manual Library (English versions only)
http://www2.yamaha.co.jp/manual/english/
V788820 ???MW???.?-01A0
M.D.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
© 2002 Yamaha Corporation
Printed in Indonesia
">