Reebok RBTL60211.0 User`s manual
Advertisement
Advertisement
www.reebokfitness.com
Model No. RBTL60211.0
Serial No.
Write the serial number in the space above for reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if parts are damaged or missing, DO NOT
CONTACT THE STORE; please contact Customer Care.
IMPORTANT: Please register this product (see the limited warranty on the back cover of this manual) before contacting Customer Care.
CALL TOLL-FREE:
1-877-994-4999
Mon.–Fri., 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB: www.reebokservice.com
CAUTION
Read all precautions and instructions in this manual before using this equipment. Keep this manual for future reference.
USER’S MANUAL
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
ORDERING REPLACEMENT PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
WARNING DECAL PLACEMENT
This drawing shows the locations of the warning decals. If a decal is missing or illegible, call the telephone number on the front cover of this manual and request a free replacement decal. Apply the decal in the
location shown. Note: The decals may not be shown at actual size.
REEBOK and the Vector Logo are registered trademarks and service marks of Reebok. This product is manufactured and distributed under license from Reebok International.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
1. Before beginning any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near water.
5. Place the treadmill on a level surface, with at least 8 ft. (2.4 m) of clearance behind it and 2 ft. (0.6 m) on each side. Do not place the treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
6. Do not operate the treadmill where aerosol products are used or where oxygen is being administered.
7. Keep children under age 12 and pets away from the treadmill at all times.
8. The treadmill should be used only by persons weighing 300 lbs. (136 kg) or less.
9. Never allow more than one person on the treadmill at a time.
10. Wear appropriate exercise clothes while using the treadmill. Do not wear loose clothes that could become caught in the treadmill. Athletic support clothes are recommended for both men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in sandals.
11. Plug the power cord into a surge suppressor
(not included), and plug the surge suppressor into an appropriate outlet (see page 13).
To avoid overloading the circuit, do not plug other electrical devices, except for low-power devices such as cell phone chargers, into the surge suppressor or into an outlet on the same circuit.
12. Use only a surge suppressor that meets all of the specifications described on page 13. To purchase a surge suppressor, see your local
REEBOK dealer, call the telephone number on the front cover of this manual, or see your local electronics store.
13. Failure to use a properly functioning surge suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may slow, accelerate, or stop unexpectedly, which may result in a fall and serious injury.
14. Keep the power cord and the surge suppressor away from heated surfaces.
15. Never move the walking belt while the power is turned off. Do not operate the treadmill if the power cord or plug is damaged, or if the treadmill is not working properly. (See
TROUBLESHOOTING on page 21 if the treadmill is not working properly.)
16. Read, understand, and test the emergency stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 15).
17. Never start the treadmill while you are standing on the walking belt. Always hold the handrails while using the treadmill.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid sudden jumps in speed.
19. The heart rate monitor is not a medical device. Various factors, including the user’s movement, may affect the accuracy of heart rate readings. The heart rate monitor is intended only as an exercise aid in determining heart rate trends in general.
3
20. Never leave the treadmill unattended while it is running. Always remove the key, unplug the power cord, and press the power switch into the off position when the treadmill is not in use. (See the drawing on page 5 for the location of the power switch.)
21. Do not attempt to raise, lower, or move the treadmill until it is properly assembled. (See
ASSEMBLY on page 7, and HOW TO FOLD
AND MOVE THE TREADMILL on page 20.)
You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill.
22. When folding or moving the treadmill, make sure that the storage latch is holding the frame securely in the storage position.
23. Never insert any object into any opening on the treadmill.
25.
DANGER:
Always unplug the power cord immediately after use, before cleaning the treadmill, and before performing the maintenance and adjustment procedures described in this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the procedures in this manual should be performed by an authorized service representative only.
26. This treadmill is intended for home use only.
Do not use this treadmill in a commercial, rental, or institutional setting.
27. Over exercising may result in serious injury or death. If you feel faint or if you experience pain while exercising, stop immediately and cool down.
24. Inspect and properly tighten all parts of the treadmill regularly.
SAVE THESE INSTRUCTIONS
4
BEFORE YOU BEGIN
Thank you for selecting the new REEBOK ®
CHALLENGER 150 treadmill. The CHALLENGER 150 treadmill provides an impressive selection of features designed to make your workouts at home more effective and enjoyable.
For your benefit, read this manual carefully before
you use the treadmill. If you have questions after reading this manual, please see the front cover of this manual. To help us assist you, note the product model number and serial number before contacting us. The model number and the location of the serial number decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with the parts that are labeled in the drawing below.
Console
Length: 6 ft. (183 cm)
Width: 2 ft. 11 in. (89 cm)
Handrail
Tray
Heart Rate
Monitor
Key/Clip
Walking Belt
Foot Rail
Power Switch
Power Cord
Platform Cushion
Idler Roller
Adjustment Screws
5
PART IDENTIFICATION CHART
Use the drawings below to identify small parts used for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see if it is preat- tached. Extra hardware may be included.
5/16" Star
Washer (8)—8
3/8" Star
Washer (5)—6
3/8" Nut (3)—1
#8 x 1/2" Ground
Screw (1)—1
#8 x 3/4" Screw
(6)—12
1/4" x 1"
Screw (9)—4
5/16" x 1"
Bolt (7)—8
3/8" x 1 3/4" Screw (12)—1 3/8" x 2" Bolt (13)—1
3/8" x 3 1/2" Screw (4)—6
6
ASSEMBLY
• To hire a service technician to assemble this product in your home, call 1-800-445-2480.
• Assembly requires two persons.
• Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until you finish all assembly steps.
• The underside of the walking belt is coated with high-performance lubricant. After shipping, there may be some lubricant on top of the walking belt or on the shipping carton. This is normal. If there is lubricant on top of the walking belt, wipe it off with a soft cloth and a mild, non-abrasive cleaner.
• To identify small parts, see page 6.
• Assembly requires the following tools: the included hex keys one adjustable wrench one Phillips screwdriver scissors needlenose pliers
To avoid damaging parts, do not use power tools.
Remove the ties securing the Upright Wire (70) to the Base (80). Pull the Upright Wire and the base ground wire (A) through the indicated hole in the Base.
Next, attach the base ground wire (A) to the Base
(80) with a #8 x 1/2" Ground Screw (1).
Then, press a Base Cap (77) into each end of the
Base (80). Make sure that the Grommet (67) is pressed into the square hole in the Base.
See the inset drawing. Cut the plastic tie near the Upright Wire (70). Be careful not to damage the Upright Wire.
1
77
70
1
A
Hole
67
80
70
Tie
Cut
7
2. Identify the Left Upright (75), which is marked
“Left.” Have a second person hold the Left
Upright near the Base (80).
See the inset drawing. Tie the wire tie in the
Left Upright (75) securely around the end of the
Upright Wire (70). Then, insert the Upright Wire into the lower end of the Left Upright as you pull the other end of the wire tie through the Left
Upright.
2
Wire
Tie
70
75
3. Hold the Left Upright (75) against the Base (80).
Be careful not to pinch the wires. Partially tighten three 3/8" x 3 1/2" Screws (4) with three
3/8" Star Washers (5) into the Left Upright and the Base; do not fully tighten the Screws yet.
Attach the Right Upright (not shown) in the
same way. Note: There are no wires on the right side.
3
70
75
Wire Tie
80
75
5 4
80
Wires
5
8
4. Identify the Left Handrail (71), which is marked
“Left.” Remove the tie from the 5/16" Cage Nut
(33). If necessary, press the Cage Nut back into place.
Hold the Left Handrail (71) near the Left Upright
(75). Insert the Upright Wire (70) through the bracket on the bottom of the Left Handrail.
Then, pull the Upright Wire out of the end of the
Handrail.
Attach the Left Handrail (71) to the Left Upright
(75) with three 5/16" x 1" Bolts (7) and three
5/16" Star Washers (8) as shown. Be careful not to pinch the Upright Wire (70). Start all three Bolts before tightening them.
Attach the Right Handrail (not shown) in the
same way. Note: There are no wires on the right side.
4
5. Identify the Left Handrail Tube (10), which is marked “Left.”
Insert the Left Handrail Tube (10) into the top of the Left Handrail (71). Attach the Left Handrail
Tube with two 1/4" x 1" Screws (9). Start both
Screws before tightening them. Then, insert a Handrail Insert (69) into the top of the Left
Handrail.
Attach the Right Handrail Tube (not shown)
in the same way.
5
71
70
75
Tie
33
8
7
8
7
9
10
69
71
9
6. With the help of a second person, hold the console assembly near the Left Upright (75).
Connect the Upright Wire (70) to the console wire. See the inset drawing. The connectors should slide together easily and snap into
place. If they do not, turn one connector and try again. IF YOU DO NOT CONNECT THE CON-
NECTORS PROPERLY, THE CONSOLE MAY
BECOME DAMAGED WHEN YOU TURN ON
THE POWER.
Remove the wire tie from the Upright Wire (70).
6
Console
Wire
Console
Wire Wire
Tie
70
7. Insert the Upright Wire (70) into the Left Upright
(75) as you set the console assembly on the Left
Handrail (71) and the Right Handrail (72). Make sure that no wires are pinched.
Attach the console assembly to the Left and
Right Handrails (71, 72) with two 5/16" x 1" Bolts
(7) and two 5/16" Star Washers (8). Start both
Bolts before tightening them.
7
71
70
8
7
75
72
8
7
Console
Assembly
70
75
Console
Assembly
10
8. Attach the console assembly to the Left and
Right Handrail Tubes (10, 11) with four #8 x 3/4"
Screws (6); start all four Screws, and then tighten them. Do not overtighten the Screws.
8
11
Console
Assembly
6
9. Identify the Left Tray (87) and the Right Tray
(88). Make sure that the indicated notch is positioned as shown. Attach the Trays with eight
#8 x 3/4" Screws (6). Start all eight Screws, and then tighten them. Do not overtighten the
Screws.
9
6
88
Notch
87
6
10
6
11
10. Fully tighten the six 3/8" x 3 1/2" Screws (4)
(three on each side).
10
4
4
11. Raise the Frame (49) to the position shown.
Have a second person hold the Frame until this step is completed.
Orient the Storage Latch (51) so that the large barrel and the latch knob are oriented as shown.
Attach the lower end of the Storage Latch (51) to the Base (80) with a 3/8" x 2" Bolt (13) and a 3/8"
Nut (3).
Attach the upper end of the Storage Latch (51) to the Frame (49) with a 3/8" x 1 3/4" Screw (12).
Lower the Frame (not shown) (see HOW TO
LOWER THE TREADMILL FOR USE on page
20).
11
49
12
51
Large
Barrel
80
13
Latch
Knob
3
12. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill.
Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used to adjust the walking belt (see pages 22 and 23).
12
OPERATION AND ADJUSTMENT
HOW TO CONNECT THE POWER CORD
Use a Surge Suppressor
Your treadmill, like other electronic equipment, can be damaged by sudden voltage changes in your home’s power. Voltage surges, spikes, and noise interference can result from weather conditions or from other appliances being turned on or off. To decrease the risk of damaging the treadmill, always use a surge suppressor with the treadmill. To purchase a surge suppressor, see precaution 12 on page 3.
Use only a surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of
450 joules. The surge suppressor must also be electrically rated for 120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to use a properly functioning surge suppressor could result in damage to the control system of the treadmill and serious injury to users.
Plug in the Power Cord
The treadmill must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. The treadmill power cord has a plug with a grounding pin (see drawing 1 on this page).
DANGER:
Improper connection of the power cord increases the risk of electric shock. Do not modify the plug—if it will not fit an outlet, have a proper outlet installed by a qualified electrician. If you are unsure whether the treadmill is properly grounded, contact a qualified electrician.
Plug the power cord into a surge suppressor, and plug the surge suppressor into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. The outlet must be on a nominal 120-volt circuit capable of carrying 15 or more amps. To avoid overloading the circuit, do not plug other electrical devices, except for lowpower devices such as cell phone chargers, into the surge suppressor or into an outlet on the same circuit. IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets and may not be compatible with AFCI-equipped outlets.
1
Grounded Outlet
Grounding Pin
Grounding Pin
Surge
Suppressor
A temporary adapter may be used to connect the surge suppressor to a 2-pole receptacle
2
Lug
2-pole Receptacle
Adapter if a properly grounded outlet is not available.
Metal
Screw
The lug or wire extending from the adapter must be connected with a metal screw to a permanent ground such as a properly grounded outlet box cover.
Some 2-pole receptacle outlet box covers are not grounded. Before using an adapter, contact a qualified electrician to determine whether the outlet box cover is grounded. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician.
13
CONSOLE DIAGRAM
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of features designed to make your workouts more effective and enjoyable.
When the manual mode of the console is selected, you can change the speed and incline of the treadmill with the touch of a button. As you exercise, the console will display instant exercise feedback. You can even measure your heart rate using the handgrip heart rate monitor.
In addition, the console offers a weight-loss workout center, designed to create custom-fit workouts to help you meet your fitness goals. Each workout automatically controls the speed and incline of the treadmill as it guides you through an effective exercise session.
You can even listen to your favorite workout music or audio books with the console’s premium stereo sound system while you get in shape.
To turn on the power, see page 15. To use the
manual mode, see page 15. To use a weight-loss
workout, see page 17. To use an iFit workout, see page 18. To use the cool-down mode, see page 18.
To use the information mode, see page 19. To use
the stereo sound system, see page 19.
IMPORTANT: If there is a sheet of plastic on the console, remove the plastic. To prevent damage to the walking platform, wear clean athletic shoes while using the treadmill. The first time the treadmill is used, observe the alignment of the walking belt, and center the walking belt if necessary (see page 23).
The console also features the iFit interactive workout system. The iFit system accepts iFit cards with workouts that help you achieve specific fitness goals.
For example, lose unwanted pounds with the 8-week
Weight Loss workout. iFit workouts automatically con-
ETGT59610 or call the telephone number on the front cover of this manual. iFit cards are also available at select stores.
Note: The console can display speed and distance in either miles or kilometers. To find out which unit of measurement is selected or to change the unit of measurement, see THE INFORMATION MODE on page
19. For simplicity, all instructions in this section refer to miles.
14
HOW TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room temperature before turning on the power. If you do not do this, you may damage the console displays or other electrical components.
Plug in the power cord (see page 13). Next, locate the power switch on the treadmill frame near the power cord. Make sure that the switch is in the reset position.
Reset
Next, stand on the foot rails of the treadmill. Find the clip attached to the key and slide the clip onto the waistband of your clothes. Then, insert the key into the con-
Clip
ETGT59610
Key sole. After a moment, the displays will light. IMPORTANT: In an emergency, the key can be pulled from the console, causing the walking belt to slow to a stop. Test the clip by carefully taking a few steps backward; if the key is not pulled from the console, adjust the position
of the clip. Note: The first time you insert the key into the console, the incline will automatically rise to the maximum incline level and then return to the minimum incline level.
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
2. Select the manual mode.
When the key is inserted, the manual mode will be selected. If a weight-loss workout has been selected, remove the key and then reinsert it.
3. Start the walking belt.
To start the walking belt, press the Go button, the
Speed increase button, or one of the Quick Speed buttons numbered 1 through 10.
If you press the Go button or the Speed increase button, the walking belt will begin to move at 1 mph. As you exercise, change the speed of the walking belt as desired by pressing the Speed increase and decrease buttons. Each time you press one of the buttons, the speed setting will change by 0.1 mph; if you hold down the button, the speed setting will change in increments of 0.5 mph. Note: After you press the buttons, it may take a moment for the walking belt to reach the selected speed setting.
If you press one of the numbered Quick Speed buttons, the walking belt will gradually change speed until it reaches the selected speed setting.
To select a speed setting that includes a decimal— such as 3.5 mph—press two numbered buttons in succession. For example, to select a speed setting of 3.5 mph, press the 3 button and then immediately press the 5 button. Note: This will not function if the console is set to metric units.
To stop the walking belt, press the Stop button. To restart the walking belt, press the Go button, the
Speed increase button, or one of the Quick Speed buttons numbered 1 through 10.
15
4. Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the
Incline increase and decrease buttons or one of the numbered Quick Incline buttons. Each time you press the incline increase or decrease button, the incline will change by 0.5 percent. If you press one of the numbered Quick Incline buttons, the treadmill will adjust to the selected incline setting. Note:
After you press the buttons, it may take a moment for the treadmill to reach the selected incline setting.
5. Monitor your progress with the displays.
Time/Distance display—When the manual mode is selected, this display will show the elapsed time.
When a workout is selected, the display will show the time remaining in the workout rather than the elapsed time. This display will also show the distance that you have walked or run.
Incline/Calories display—This display will show the incline setting for several seconds, each time the incline changes. This display will also show the approximate amount of calories you have burned.
Heart Rate/Speed display—This display will show your heart rate when you use the handgrip heart rate monitor. This display will also show the speed of the walking belt.
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
6. Measure your heart rate if desired.
Before using the handgrip heart rate monitor, first remove the sheets of plastic from the metal contacts. In addition, make sure that your hands are clean.
Contacts
To use the handgrip heart rate monitor, stand on
the foot rails and hold the metal contacts—avoid
moving your hands. When your pulse is detected, your heart rate will be shown. For the most accu- rate heart rate reading, continue to hold the contacts for about 15 seconds.
7. When you are finished exercising, remove the key from the console.
Step onto the foot rails, press the Stop button, and adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest set- ting or you may damage the treadmill when you
fold it to the storage position. Next, remove the key from the console and put it in a secure place.
When you are finished using the treadmill, press the power switch into the off position and unplug the power cord. IMPORTANT: If you do not do this, the treadmill’s electrical components may wear prematurely.
16
HOW TO USE A WEIGHT-LOSS WORKOUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 15.
2. Select a time for the workout.
To select a weight-loss workout, first press one of the Set Time buttons. The duration of the workout will appear in the Time/Distance display.
3. Select the amount of calories you want to burn.
Next, press one of the Set Cals buttons. Note: The console will create a custom workout based on the duration of the workout and the amount of calories you want to burn. You might not be able to select a high amount of calories with a short duration for the workout.
Note: The calorie goal is an estimate of the number of calories that you will burn during the workout. The actual number of calories that you burn will depend on your metabolic rate. In addition, if you manually change the speed or incline of the treadmill during the workout, the number of calories you burn will be affected.
4. Select a user weight.
One of the main factors that contributes to your metabolic rate is your weight. Press the Set Wt. increase and decrease buttons to enter your weight. This will allow the console to calculate the amount of calories you will burn more accurately.
The console will adjust the workout’s intensity level according to the weight entered.
5. Start the walking belt.
Press the Go button or the Speed increase button to start the workout. A moment after you press the button, the treadmill will automatically adjust to the first speed and incline settings of the workout. Hold the handrails and begin walking.
Each workout is divided into one-minute segments.
One speed setting and one incline setting are programmed for each segment. Note: The same speed setting and/or incline setting may be programmed for consecutive segments.
At the end of each segment, a series of tones will sound. If a different speed or incline setting is programmed for the next segment, the Next Incline and/or Next Speed indicator will alert you. The speed or incline setting will also flash in the display to alert you. The treadmill will then automatically adjust to the speed and incline settings for the next segment.
The workout will continue in this way until the last segment of the profile flashes in the display and the last segment ends. The walking belt will then slow to a stop.
If the speed or incline setting is too high or too low at any time during the workout, you can manually override the setting by pressing the Speed or
Incline buttons; however, when the next seg- ment of the workout begins, the treadmill will automatically adjust to the speed and incline settings for the next segment.
To stop the workout at any time, press the Stop button. To restart the workout, press the Go button. The walking belt will begin to move at 1 mph.
When the next segment of the workout begins, the treadmill will automatically adjust to the speed and incline settings for the next segment.
6. Monitor your progress with the displays.
See step 5 on page 16.
7. Measure your heart rate if desired.
See step 6 on page 16.
8. When you are finished exercising, remove the key from the console.
See step 7 on page 16.
17
HOW TO USE AN IFIT WORKOUT
Note: An iFit card is included with this product. To purchase additional iFit cards at any time, go to www.iFit.com or call the telephone number on the front cover of this manual. iFit cards are also available at select stores.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 15.
2. Insert an iFit card and select a workout.
To use an iFit workout, insert an iFit card into the iFit slot; make sure that the iFit card is oriented so that the metal contacts are face-down and are inserted into the iFit slot. When the iFit card is correctly inserted, the iFit logo will light up.
iFit Card iFit Slot iFit Logo
During the workout, the voice of a personal trainer will guide you through the workout.
If the speed or incline setting for the current segment is too high or too low, you can manually override the setting by pressing the Speed or
Incline buttons; however, when the next segment begins, the treadmill will automatically adjust to the speed and incline settings for the next segment.
To stop the workout at any time, press the Stop button. To restart the workout, press the Go button or the Speed increase button. The walking belt will begin to move at 1 mph. When the next segment of the workout begins, the treadmill will automatically adjust to the speed and incline settings for the next segment.
4. Monitor your progress with the displays.
See step 5 on page 16.
5. Measure your heart rate if desired.
See step 6 on page 16.
6. When you are finished exercising, remove the key from the console.
See step 7 on page 16.
CAUTION: Always remove iFit cards from the iFit slot when you are not using them.
Next, select an iFit workout by pressing the iFit increase and decrease buttons next to the iFit slot. When an iFit workout is selected, the workout duration, the maximum incline setting, the name, and the maximum speed setting of the workout will appear in the displays.
Each iFit workout is divided into several one-minute segments. One speed setting and one incline setting are programmed for each segment. Note: The same speed and/or incline setting may be programmed for consecutive segments.
3. Start the walking belt.
Press the Go button or the Speed increase button to start the workout. A moment after you press the button, the treadmill will automatically adjust to the first speed and incline settings of the workout. Hold the handrails and begin walking.
THE COOL-DOWN MODE
To select the cool-down mode, press the Cool Down button. The treadmill will adjust to the lowest incline, and the walking belt will begin to slow down incrementally, once per minute for five minutes, unless the walking belt speed is already around 2 mph. After five minutes, the walking belt will slow to a stop.
18
THE INFORMATION MODE
The console features an information mode that keeps track of the total number of hours that the treadmill has been used and the total distance that the walking belt has moved. The information mode also allows you to select miles or kilometers as the unit of measurement.
To select the information mode, hold down the Stop button while inserting the key into the console and then release the Stop button. When the information mode is selected, the following information will be shown:
The Incline/Calories display will show the total number of hours the treadmill has been used.
The Time/Distance display will show the total number of miles (or kilometers) that the walking belt has moved.
HOW TO USE THE STEREO SOUND SYSTEM
To play music or audio books through the console’s stereo speakers, you must connect your MP3 player,
CD player, or other personal audio player to the console through the audio jack.
To use the audio jack, locate the audio wire and plug it into the audio jack below the Cool Down button. Then, plug the audio wire into a jack on your MP3 player, CD player, or other personal audio player. Make sure that the audio wire is fully plugged in.
Next, press the play button on your MP3 player,
CD player, or other personal audio player.
Adjust the volume on your personal audio player or press the volume increase and decrease buttons on the console.
Increase
Decrease
If you are using a personal CD player and the CD skips, set the CD player on the floor or another flat surface instead of on the console.
An “E” for English miles or an “M” for metric kilometers will appear in the Heart
Rate/Speed display. Press the Speed increase button to change the unit of measurement if desired.
To exit the information mode, remove the key from the console.
19
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL
To avoid damaging the treadmill, adjust the incline to the lowest position before you fold the treadmill.
Then, remove the key and unplug the power cord.
CAUTION: You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by the arrow below. CAUTION: Do not hold the frame by the plastic foot rails. Bend your legs and keep your back straight.
HOW TO MOVE THE TREADMILL
Before moving the treadmill, fold it as described at the left. CAUTION: Make sure that the latch knob is locked in the storage position. Moving the treadmill may require two people.
1. Hold the frame and one of the handrails, and place one foot against a wheel.
1
Frame
1
Frame
Handrail
Wheel
2. Raise the frame until the latch knob locks in the storage position. CAUTION: Make sure that the latch knob locks.
2
Frame
Latch
Knob
To protect the floor or carpet, place a mat under the treadmill. Keep the treadmill out of direct sunlight.
Do not leave the treadmill in the storage position in temperatures above 85° F (30° C).
2. Pull back on the handrail until the treadmill will roll on the wheels, and carefully move it to the desired location. CAUTION: Do not move the tread- mill without tipping it back, do not pull on the frame, and do not move the treadmill over an uneven surface.
3. Place one foot against a wheel, and carefully lower the treadmill.
HOW TO LOWER THE TREADMILL FOR USE
See drawing 2. Hold the upper end of the treadmill frame with your left hand. Then, pull the latch knob to the right. IMPORTANT: Do not turn the
latch knob. If necessary, push the frame forward slightly. Pivot the frame downward a few inches, and release the latch knob.
See drawing 1 at the left. Hold the metal frame firmly with both hands, and lower it to the floor.
CAUTION: Do not hold the frame by the plastic foot rails, and do not drop the frame. Bend your
legs and keep your back straight.
20
TROUBLESHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.
SYMPTOM: The power does not turn on a. Make sure that the power cord is plugged into a surge suppressor and that the surge suppressor is plugged into a properly grounded outlet (see page 13). Use only a surge suppressor that meets all of the specifications described on page 13.
IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets and may not be compatible with AFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the power switch located on the treadmill frame near the power cord. If the switch protrudes as shown, the switch has tripped. To reset the power switch, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.
c. Remove the key from the console, and then reinsert it.
d. If the treadmill still will not run, please see the front cover of this manual.
SYMPTOM: The displays of the console do not function properly a. Remove the key from the console and UNPLUG
THE POWER CORD. Place the treadmill in the storage position (see HOW TO FOLD THE
TREADMILL on page 20).
a
6 c
6
Tripped Reset
SYMPTOM: The power turns off during use a. Check the power switch (see the drawing above).
If the switch has tripped, wait for five minutes and then press the switch back in.
Next, remove the two indicated #8 x 3/4" Screws
(6).
21
Lower the treadmill (see HOW TO LOWER THE
TREADMILL FOR USE on page 20). Remove the three #8 x 3/4" Screws (6). Carefully slide the
Motor Hood (57) off.
57
6
6
Locate the Reed Switch (95) and the Magnet (44) on the left side of the Pulley (43). Turn the Pulley until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet
and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the #8 x 3/4" Truss Head Screw
(19), move the Reed Switch slightly, and then retighten the Screw. Reattach the Motor Hood (not shown) with the five #8 x 3/4" Screws (not shown) and run the treadmill for a few minutes to check for a correct speed reading.
recalibrate the incline system. If the incline does not begin calibrating, press the Stop button again, and then press the Incline increase or decrease button again. When the incline is calibrated, remove the key from the console.
SYMPTOM: The walking belt slows when walked on a. Use only a surge suppressor that meets all of the specifications described on page 13.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
b
2–3 in.
Front
View
43
44
1/8 in.
95
19
Idler Roller Screws
SYMPTOM: The incline of the treadmill does not change correctly a. Hold down the Stop button and the Speed increase button, insert the key into the console, and then release the Stop button and the Speed increase button. Press the Stop button and then press the
Incline increase or decrease button. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will c. Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform unless instructed to do so by an authorized service representative. Such substances may deterio-
rate the walking belt and cause excessive wear.
If you suspect that the walking belt needs more lubricant, see the front cover of this manual.
d. If the walking belt still slows when walked on, see the front cover of this manual.
22
SYMPTOM: The walking belt is off-center or slips when walked on
If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex key to turn the left idler roller screw clockwise 1/2 of a turn; if the walking belt has shifted to the
right, turn the left idler roller screw counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered. a
If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER
CORD. Using the hex key, turn both idler roller screws clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to
7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
b
23
EXERCISE GUIDELINES
WARNING:
Before beginning this or any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems.
The heart rate monitor is not a medical device.
Various factors may affect the accuracy of heart rate readings. The heart rate monitor is intended only as an exercise aid in determining heart rate trends in general.
These guidelines will help you to plan your exercise program. For detailed exercise information, obtain a reputable book or consult your physician. Remember, proper nutrition and adequate rest are essential for successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for fat burning and aerobic exercise.
To find the proper intensity level, find your age at the bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your age define your “training zone.” The lowest number is the heart rate for fat burning, the middle number is the heart rate for maximum fat burning, and the highest number is the heart rate for aerobic exercise.
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of time. During the first few minutes of exercise, your body uses carbohydrate calories for energy. Only after the first few minutes of exercise does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the lowest number in your training zone. For maximum fat burning, exercise with your heart rate near the middle number in your training zone.
Aerobic Exercise—If your goal is to strengthen your cardiovascular system, you must perform aerobic exercise, which is activity that requires large amounts of oxygen for prolonged periods of time. For aerobic exercise, adjust the intensity of your exercise until your heart rate is near the highest number in your training zone.
WORKOUT GUIDELINES
Warming Up—Start with 5 to 10 minutes of stretching and light exercise. A warm-up increases your body temperature, heart rate, and circulation in preparation for exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During the first few weeks of your exercise program, do not keep your heart rate in your training zone for longer than 20 minutes.) Breathe regularly and deeply as you exercise—never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each week, if desired. Remember, the key to success is to make exercise a regular and enjoyable part of your everyday life.
24
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch —never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times. Stretches: Hamstrings, back of knees and back.
2. Hamstring Stretch
1
Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg. Reach toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and groin.
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your hands against a wall. Keep your back leg straight and your back foot flat on the floor. Bend your front leg, lean forward and move your hips toward the wall. Hold for 15 counts, then relax. Repeat 3 times for each leg. To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles tendons and ankles.
3
2
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. Repeat 3 times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for 15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip muscles.
5
25
NOTES
26
PART LIST
Model No. RBTL60211.0 R1211A
Key No. Qty. Description Key No. Qty. Description
25
26
27
28
29
30
31
32
17
18
19
20
21
22
23
24
33
34
35
36
37
38
39
40
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
4
1
1
1
2
2
2
2
2
2
2
8
2
3
17
2
1
1
1
1
2
1
1
2
1
2
2
2
4
1
1
1
6
39
8
8
5
2
5
6
#8 x 1/2" Ground Screw
3/8" x 2 1/2" Bolt
3/8" Nut
3/8" x 3 1/2" Screw
3/8" Star Washer
#8 x 3/4" Screw
5/16" x 1" Bolt
5/16" Star Washer
1/4" x 1" Screw
Left Handrail Tube
Right Handrail Tube
3/8" x 1 3/4" Screw
3/8" x 2" Bolt
1/4" x 2 1/2" Screw
3/8" x 1 3/8" Bolt
1/2" x 2 1/4" Bolt
1/2" Nut
Hood Clip
#8 x 3/4" Truss Head Screw
3/8" x 1 1/2" Bolt
3/8" Jam Nut
Incline Motor Spacer
1/4" x 3/8" Screw
#8 x 7/16" Screw
5/16" x 1 1/4" Bolt
Base Pad Spacer
5/16" x 1 3/4" Bolt
5/16" Washer
5/16" Nut
Hood Accent
Left Speaker Cover
1/4" x 1 3/4" Screw
5/16" Cage Nut
Hex Key
5/32" Hex Key
Platform Cushion
Left Foot Rail
Latch Warning Decal
Walking Platform
Walking Belt
41
42
2
2
Belt Guide
Rubber Spacer
43 1 Drive Roller/Pulley
44 1 Magnet
45
46
47
48
1
1
1
2
Reed Switch Clamp
Drive Motor Belt
Drive Motor
Frame Spacer
49 1 Frame
50
51
52
53
54
55
56
57
58
59
60
61
1
1
1
1
1
1
1
1
2
1
1
1
Right Foot Rail
Storage Latch
Right Rear Foot
Left Rear Foot
Right Speaker Back
Left Speaker Back
Idler Roller
Motor Hood
Incline Frame Spacer
Incline Frame
Incline Motor
Controller Ground Wire
62 1 Controller
63
64
65
66
3
1
Wire Tie
Belly Pan Plate
67 2 Grommet
68
69
70
71
72
73
74
75
1
1
1
2
1
1
1
2
2
1
Power Switch
Power Cord
Belly Pan
Handrail Insert
Upright Wire
Left Handrail
Right Handrail
Handrail Cap
Handrail Tube Cap
Left Upright
76
77
78
79
1
4
2
4
Right Upright
Base Cap
Caution Decal
Base Pad
80 1 Base
81 2 Wheel
82 1 Key/Clip
83 1 Console Base
84 2 Speaker
85 1 Audio Wire
86 1 Console
87
88
89
90
91
92
93
94
95
96
*
2
12
1
4
1
1
1
1
1
8
–
Left Tray
Right Tray
Console Ground Wire
Pulse Bar Bottom
Console Wire Tie
#3 x 1/4" Screw
Right Speaker Cover
#8 x 1/2" Pan Head Screw
Reed Switch
#8 x 1" Tek Screw
User’s Manual
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see the back cover of this manual. *These parts are not illustrated.
27
EXPLODED DRAWING A
42 28
Model No. RBTL60211.0 R1211A
28
EXPLODED DRAWING B
6
Model No. RBTL60211.0 R1211A
6
6
59
58
3
30
3
58
57
17
20
6
6
20
6
6
22
68
21
60
17
21
94
18
6
1
61
63
29
6
18
62
6
6
64
18
66
65
6
67
1
EXPLODED DRAWING C
9
69
33
71
73
8
7
8
8
7
70
7
4
75
5
Model No. RBTL60211.0 R1211A
6
10
74
6
8
7
72
9
7
8
11
6
69
33
8
7
6
74
73
1
15
77
78
76
15
2
67
96
26
79
78
77
5
4
77
96
79
81
3 80
3
77
81 96
26
79
5
4
79
96
2
30
EXPLODED DRAWING D
31
84
92
87
55
92
92
6
6
92
6
6
91
83
6
86
94
6
6
93
Model No. RBTL60211.0 R1211A
82
6
92
84
54
92
92
92
94 6
6
88 6
6
92
90
6
6
1
89
6
85
6
31
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED DRAWING near the end of this manual)
LIMITED WARRANTY
IMPORTANT: You must register this product within 30 days of the purchase date to avoid added fees for service needed under warranty. Go to www.reebokservice.com/registration.
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and material, under normal use and service conditions. The frame is warranted for a lifetime. The drive motor is warranted for twenty-five (25) years from the date of purchase. Parts and labor are warranted for one
(1) year from the date of purchase.
This warranty extends only to the original purchaser (customer). ICON’s obligation under this warranty is limited to repairing or replacing, at ICON’s option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped to a service center, freight charges to and from the service center will be the customer’s responsibility. If replacement parts are shipped while the product is under warranty, the customer will be responsible for a minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge.
This warranty does not extend to freight damage to the product. This warranty will automatically be voided if the product is used as a store display model, if the product is purchased or transported outside the USA, if all instructions in this manual are not followed, if the product is abused or improperly or abnormally used, or if the product is used for commercial or rental purposes. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other consequential damages of any kind. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to the customer.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to the customer.
This warranty provides specific legal rights; the customer may have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 325567 R1211A Printed in China © 2011 ICON IP, Inc.

Public link updated
The public link to your chat has been updated.
Advertisement