AEG | HOBS | Service manual | AEG HOBS Service manual

SERVICE MANUAL
HOBS
Induction Glass Ceramic
Cooking Surface
© AEG Hausgeräte GmbH
Muggenhofer Straße 135
D-90429 Nürnberg
Germany
Fax +49 (0)911 323 1420
TSE - N
Edition:
05.00
Publ.-Nr.:
599 50 82 38
685
EN
C 67100 K
C 68000 K
C 88900 K
CONTENTS
Special notes on induction cooking zones ...................................................................... 3
How to avoid damaging your appliance .......................................................................... 4
Appliance description ................................................................................................... 4
Function and the way the induction cooking zone works ................................................ 4
Features of the ceramic hob C67100K ........................................................................... 5
Features of the ceramic hob C68000K ........................................................................... 5
Control field C67100K and C68000K .............................................................................. 5
Features of the ceramic hob C88900K ........................................................................... 6
Control field C889000K ................................................................................................... 6
The digital displays.......................................................................................................... 7
Safety cutoff of the cooking zone (Hob C89000K).......................................................... 8
Resetting the safety cut-out ............................................................................................ 8
Suitable kitchenware for induction cooking zones .......................................................... 8
Pan size .......................................................................................................................... 9
Automatic pan sensing .................................................................................................... 9
Pots and pans for rapid-glowing standard cooking zones (Hob C67600M) .................... 9
Before using for the first time ........................................................................................ 10
-
10
Using the cooking zones ............................................................................................ 11
TOUCH CONTROL sensor field ................................................................................... 11
Switching on the appliance ........................................................................................... 11
Switching off the Appliance ........................................................................................... 11
Cooking Zone Selection ................................................................................................ 12
Heat Level Selection + and - ......................................................................................... 12
Cooking without the Automatic Heating-Up Function ................................................... 12
Cooking with the Automatic Heating-Up Function ........................................................ 13
Switching the Double ring cooking zone On and Off (C67100K) .................................. 14
Aktivating the power function (C67100K) ...................................................................... 15
Activating the power function (C68000K and C88900K) ............................................... 15
Activate Warming Zone (C88900K) .............................................................................. 16
Locking/Unlocking the Control Panel ............................................................................ 16
Timer
........................................................................................................................ 16
-
16
Cleaning and care ....................................................................................................... 18
Advantages for cleaning and caring for the induction cooking zone ............................ 18
Glass ceramic cooking surface ..................................................................................... 18
Problem dirt ...................................................................................................................19
-
19
Installation Instructions ............................................................................................. 20
Installation (C67100K und C68000K)............................................................................ 21
Installation (C88900K)................................................................................................... 21
Installation ..................................................................................................................... 22
Technical data (C67100K, C68000K, C88900K) .......................................................... 23
Safety instructions for the installer ................................................................................ 24
Electrical connection ..................................................................................................... 24
-
24
Additional information for the service ...................................................................... 25
Cooktop assembly ........................................................................................................ 25
Cooktop technology ...................................................................................................... 25
Compatibility ..................................................................................................................25
Cooktop assembly 4 Induction ...................................................................................... 26
Cooktop assembly 2 Induction ...................................................................................... 28
-
29
-
27
29
What to do if ... ............................................................................................................ 20
TSE-N 05.00 A. B.
-2-
599 50 82 38
EN
Special notes on induction cooking zones
-
Scientific investigations have shown that an influence on or endan-gering of patients with
implanted heart pace makers by AEG induc-tion cooking zones are normally not to be expected.
The distance between the trunk and the cooking zone should howe-ver never be less than 30 cm!
-
Electromagnetic fields can influence electronic circuits and interfere with transistor radios.
-
Do not put magnetically rechargable objects (e.g. credit cards, casset-tes etc.) on the glass
ceramic surface while the induction cooking zone(s) is (are) in use!
-
Do not put any metallic objects (e.g. spoons, pan lids etc.) on the induction surface, since they can
be warmed up when the induction surface is in use.
Certain cooking pots may produce some noise during cooking on induction cooking zones. This,
however, is no malfunction of the cooking zone and this does not affect the function in any way.
TSE-N 05.00 A. B.
-3-
599 50 82 38
EN
How to avoid damaging your appliance
-
Do not use the cooking surface as a work surface or for storage.
Do not use the cooking zones with empty pots and pans.
Glass ceramic is insensitive to temperature shock and very robust, however it is not unbreakable.
Especially sharp and hard objects that fall on the cooking surface can damage it.
Do not use pans with damaged bases that are rough and have burrs. Scratching may occur when
the pans are slid.
Do not place any pans on the cooking surface frame. Scratching may occur or the paint damaged.
Make sure that no acidic liquids, e.g. vinegar, lemon or descaling agents are spilt onto the frame of
the cooking surface, since these cause matte spots.
If sugar or a preparation with sugar comes into contact with the hot cooking zone and melts there it
must be cleaned off immediately with a scraper while it is still hot. If it cools, damage to the surface
may occur on removal.
Keep all items and materials that can melt away from the glass cera-mic surface, e.g. plastics,
aluminium foil, or oven foils. If something of this nature should melt onto the glass ceramic surface,
it must also be removed immediately using the scraper.
Avoid boiling pans dry. The bases could be irreparably damaged in the process and the glass
ceramic cooking surface also damaged.
Appliance description
Function and the way the induction cooking zone works
A copper wire induction coil is beneath the glass ceramic cooking surface. This generates
electromagnetic fields, which act directly on the base of the pots and pans and not, as with other heating
up methods, first heat up the glass ceramic. This means that the base of the pan is immediately heated
up, which saves time and energy. Since the heat required for cooking is generated directly in the base of
the pan the cooking zone itself hardly warms up. It only receives the reflected heat from the pan base.
Note:
If there is no pot or pan on the cooking zone there is no energy transfer (heating up) and thereby
absolute security against acci-dental switching on.
For technical reasons it is necessary that a cooling blower operates
when the induction cooking zone is on.
TSE-N 05.00 A. B.
-4-
599 50 82 38
EN
Features of the ceramic hob C67100K
Cooking zone 2:
Radiant heat single ring zone
1200 W
Cooking zone 3:
Radiated heat double ring cooking zone 1700 W
Cooking zone 4:
Induction cooking zone
1400 W
Cooking zone 1:
Induction cooking zone 2200 W;
with power function 3000 W
Touch-control panel
Features of the ceramic hob C68000K
Cooking zone 2:
Induction cooking zone 1800 W
Cooking zone 3:
Induction cooking zone 1400 W
Cooking zone 1:
Induction cooking zone 2200 W;
with booster function 3000 W
Cooking zone 4:
Induction cooking zone 1800 W;
with booster function 2300 W
Touch-control panel
Control field C67100K and C68000K
Display timer
Heat setting
displays
Cooking zone displays
Timer operation
Timer
Cooking zone selection
Main button “On/Off”
Power/double ring cooking zone activation
TSE-N 05.00 A. B.
Interlock with indicator lamp
-5-
Cooking stage selection “+” and “-”
599 50 82 38
EN
Features of the ceramic hob C88900K
Cooking zone 3:
Induction cooking zone 1400 W
Cooking zone 2:
Induction cooking zone 1800 W
warming zone 120 W
Cooking zone 4:
Induction cooking zone 1800 W;
with booster function 2300 W
Cooking zone 1:
Induction cooking zone 2200 W;
with booster function 3000 W
Touch-control panel
Control Field C88900K
Heat setting displays
Cooking zone displays Display timer
Timer operation
Interlock with indicator lamp
Warming zone
“Off”
Timer
Cooking zone selection
Warming zone
Warming zone
“Preparation” with “On” mit
power indicator
power indicator
“On/Off”
Power/double ring cooking Cooking stage
zone activation
selection “+” and “-”
TSE-N 05.00 A. B.
-6-
599 50 82 38
EN
The digital displays
Digits 1 to 9 and four different letters can appear in the display.
-
The digits show the cooking stage set.
=
the lowest capacity
=
the highest capacity
=
intermediate stage (= 6,5)
-
The letters indicate the functions:
=
Error Display
flashes if the cooking zone is switched on
no pan is on the cooking zone or
an unsuitable pot or pan is being used.
=
Automatic Heating Up (possible for all cooking zones)
is lit, if the cooking zone is set to automatic heating up; (is lit until the automatic feature
switches over to the set further cooking stage).
=
Residual Heat Display
Danger! Cooking zone still hot; it extinguishes when the cooking zone has cooled
down. This display appears only if the cooking zone is switched off.
=
Power Function
lights up when the Power Function is activated. The Power Function delivers extra-high
heating power. It can be switched on for cooking zone 1 (front left ø 210 mm).
=
lights up when
the cooking zone is overheated or
the automatic switch-off function has been activated.
(also see “What to do when ...“)
TSE-N 05.00 A. B.
-7-
599 50 82 38
EN
Safety cutoff for the rings
If one of the rings is not switched off after a certain time or if the cooking setting is not changed, all the
rings are automatically switched off.
appears in the cooker and the ceramic hob ring displays of all
the rings that were switched on.
-
Cooking setting 1 – 2
Cooking setting 3 – 4
Cooking setting 4 – 5
Cooking setting 5 – 9
after 6 hours
after 5 hours
after 4 hours
after 1.5 hours
Resetting the safety cut-out
Turn all the ring switches to the zero position to cancel the active safety cutoff of the rings. The rings are
then ready for operation again.
appears in the ceramic hob display if residual heat is still present.
Suitable kitchenware for induction cooking zones
Pots and Pans
-
In principle all pots and pans with magnetic bases are suitable. These are steel, steel-enamel as
well as cast-iron pots and pans.
High grade steel pans with a mixed metal base (sandwich base, e.g. Tefal with an aluminium/
copper base) are suitable for induction only if the manufacturer has expressly marked them as
such. In that case they have a ferromagnetic percentage in the base.
If you wish to use a special type of pan (e.g. a pressure cooker, sim-mering pan, wok, etc.), please
observe the manufacturer’s instruc-tions.
Aluminium, copper, brass, stainless steel pots and pans (unless especi-ally designated as suitale
for induction), glass, ceramic or porcelain are not suitable for induction cooking zones. The
cooking zone reacts as if it were being used without a pot or pan: Error code .
Look for the label: Suitable for induction!
Suitability Test
If you are not sure if a pot or pan is suitable for cooking or frying on
the induction cooking zone you can check this as follows:
-
Place a pot filled with a little water (3-5 mm filling height) on the cooking zone. Switch the cooking
zone to full power (switch setting 9).
Caution: The pan base of suitable kitchenware heats up within a few seconds!
-
You can also check this with a magnet. If it remains fixed to the base the pan is suitable for
induction cooking zones.
TSE-N 05.00 A. B.
-8-
599 50 82 38
EN
Pan size
Up to a certain limit the induction cooking zone adapts itself to the size of the pan base diameter.
However, the pan base diameter must be of a minimum size, depending on the size of the cooking zone.
For example: Diameter of the cooking zone 14,5 cm
For example: Diameter of the pan base at least 12 cm
For example: Diameter of the cooking zone 18 cm
For example: Diameter of the pan base at least 14,5 cm
For example: Diameter of the cooking zone 21 cm
For example: Diameter of the pan base at least 18 cm
Note:
Please note the diameter of the pan base when buying new pans, since the manufacturers usually
specify the top edge diameter of their pans.
Automatic pan sensing
The induction cooking zone does not function when unsuitable pans are used.
If the cooking zone is switched on without a suitable pan on it
the cooking zone.
flashes in the digital display of
After about 10 minutes the cooking zone switches itself off automati- cally.
display.
appears in the digital
Also when overheating occurs (e.g. heating up a pan cooked empty) or with faults in the electronics the
display
is lit. The cooking zone switches itself off automatically.
To be able to switch it on again the cooking zone must have been first switched off and then set to the
required stage anew.
Pots and pans for rapid-glowing standard cooking zones (Hob C67600K)
-
On principle all pots and pans with level bases are suitable for radiant heat cooking zones. You
can recognise good quality pans by the base of the pan, and not from the material from which the
pan is made.
The base should be as thick and flat as possible. Rough bases (e.g. cast iron pots) scratch the hob
surfaces when they are slid about.
Pots with aluminium or copper bases can cause metallic discolouring on the glass ceramic surface,
which is very difficult or impossible to remove.
The saucepan base and cooking zone should be the same size.
Attention! Avoid letting enamel saucepans and frying pans boil dry. The base could be damaged and
then scratch the cooking surface when slid. Saucepans and frying pans with sharp edges and burrs will
also scratch.
TSE-N 05.00 A. B.
-9-
599 50 82 38
EN
Energy saving tips
-
Always place pans on the cooking zone before switching on.
Ensure that the pots and pans are in the centre of the cooking zone and cover the heated/marked
surface.
Dirty cooking zones and pan bases damage the glass ceramic cooking surface and increase
electricity consumption.
Switch the cooking zone off before cooking is finished to use the residual heat.
Cooking times are reduced by up to 50%. Not only do you save energy, but more vitamins and
minerals are retained.
You will waste energy if the....
Before using for the first time
Initial Cleaning
Wipe the glass ceramic cooking surface with a damp cloth.
Important: Do not use any caustic, abrasive cleaners! The surface could be damaged.
TSE-N 05.00 A. B.
- 10 -
599 50 82 38
EN
Using the cooking zones
TOUCH CONTROL sensor field
To operate the TOUCH CONTROL sensor field, place you finger from
above and flat onto the required field until the corresponding indicator
lamp lights up or goes out, or until the required function is carried out.
For more speedy adjustment, keep your finger on the sensor field until
the required value is reached.
All entries are acknowledged by an acoustic signal.
Switching on the appliance
The complete unit is switched on with the “On/Off” sensor field
.
Touch the “On/Off” sensor field for approximately 2 seconds. The digital displays show
decimal point flashes.
and the
After you have actuated the “On/Off” sensor field to switch on your unit, one of the cooking zones must
be selected with the cooking zone selection keys within approximately 10 seconds. Otherwise, the unit
switches itself off again for safety reasons.
Switching off the Appliance
To completely switch off the unit, activate the “On/Off” sensor field
.
Touch the “On/Off” sensor field for approximately 1 second.
After a single cooking zone or the entire cooking field has been switched off, remaining residual heat is
shown in the digital displays of the corresponding cooking zones with
(for “hot”).
If all cooking zones are switched off, the appliance switches off automatically after a period of time.
TSE-N 05.00 A. B.
- 11 -
599 50 82 38
EN
Cooking Zone Selection
To select the required cooking zone touch the corresponding sensor field for approximately 1 second.
lights up in the associated display field of the cooking zone. The
The zero with a decimal point
decimal point indicates that settings can only be made in this cooking zone. When you touch the cooking
zone sensor field again, the decimal point goes out and further settings are not possible.
To switch off the sensor fields, press
Heat Level Selection
and
simultaneously.
and
For setting and adjusting the heat level (
zone.
to
) on the selected cooking
Increase the heat level with the sensor field .
Reduce the heat level with the sensor field .
If several cooking zones are simultaneously in operation, in order to adjust the heat level it is necessary
to select the corresponding cooking zone by touching the appropriate sensor field. A decimal point in the
display shows the selected cooking zone.
Cooking without the Automatic Heating-Up Function
1.
2.
3.
For heating up/browning, select a high power.
As soon as steam forms or the fat is hot, switch back to the required continued cooking stage.
Reset to zero in order to end cooking.
Note:
When cooking with the induction cooking zone you should take into account that
-
the heating-up times are reduced by the direct energy transfer to the pan!
the cooking process stops immediately after the cooking zone is swit-ched off (no boiling over!)
TSE-N 05.00 A. B.
- 12 -
599 50 82 38
EN
Cooking with the Automatic Heating-Up Function
All four cooking zones of the cooking field can be controlled in nine
stages and have an automatic heating-up function:
-
, Lowest cooking stage
, Highest cooking stage
, Heating-up function.
With the automatic heating-up function ( ), the cooking zone operates for a certain time at full capacity
and then automatically switches back to the set continued cooking stage.
The duration of the automatic heating-up function depends on the sel-ected continued cooking stage.
1.
Select the required cooking zone with the cooking zone sensor fields. The decimal point in the
associated display field illuminates.
2.
With the
or
field again.
sensor fields set the cooking stage
. Put down briefly and press the
sensor
lights up in the cooking stage display.
3.
and set the required continued cooking stage
Next, press the sensor field
continued cooking stage set is then displayed.
to
. The
After 5 seconds,
appears in the display again instead of the continued cooking stage. The continued
cooking stage is displayed again after the heating-up time expires.
If you select a higher stage when the automatic function is in operation, e.g. from
to , the previous
heating-up time is taken into account. If you select a lower stage, then the automatic function is brought
to an immediate end. If you start cooking again on a cooking zone that is still warm, the automatic
heating-up function uses the residual heat. This saves time and energy.
TSE-N 05.00 A. B.
- 13 -
599 50 82 38
EN
Switching the Double ring cooking zone On and Off (C67100K)
1.
Select the corresponding cooking zone.
2.
Set the required cooking stage.
3.
To switch the double ring cooking zone on or off, place your finger flat onto the touch “switch on
until the indicator lamp lights up or goes out.
double ring cooking zone” control field
TSE-N 05.00 A. B.
- 14 -
599 50 82 38
EN
Activatiang the power function (C67100K)
The cooking zone must be selected (decimal point in the display) in order to switch on the PowerFunction (*only in the case of cooking zone 1 front left ø 210 mm). Touch the sensor field “Power/
double ring cooking zone activation” .
appears in the display and the Power function is now active.
The Power function is activated for a maximum of 10 minutes. Then the cooking zone switches
automatically to cooking stage 9.
While the Power function of cooking zone 1 is active, the cooking zone 4 (front right induction cooking
zone Ø 145mm) can be operated at maximum heat setting 7. If a higher setting than 7 (e.g. 8, 9 or A) is
set for cooking zone 4, the cooking stage display alternately shows the set setting and 7. As soon as the
Power function has ended with cooking zone 1 (max. 10 minutes), cooking zone 4 automatically
changes to the previously set heat setting.
Activating the power function (C68000K and C88900K)
Using the Power function “P” you can increase the power of both front cooking zones for 10 minutes.
With this function, you can bring a large quantity of water rapidly to the boil or brown meat very well, for
example.
To switch on the Power function, the cooking zone must be selected (decimal point in the display).
Touch the sensor field “Power-function” . In the display a
appears. The Power function is now
active.
The Power function is activated for a maximum of 10 minutes. After-wards, the cooking zone
automatically switches to cooking stage 9.
The Power function can be canceled as follows:
Touch the “Power function”
sensor.
Touch the - sensor field.
As soon as the Power function is activated for one of the front cooking zones, less heating power is
given to the back cooking zones.
If the Power function for the front right cooking zone is activated, the left back cooking zone can only
attain a maximum heating power level of “8”.
If the Power function for the front left cooking zone is activated, the right back cooking zone can only
attain a maximum heating power level of “7”.
If a higher level than 7 or 8 is set for the back cooking zones in this case, the display of the cooking zone
concerned shows the differing levels in alternation (e.g., 7 and 9).
As soon as the Power function is finished (after a maximum of 10 minutes), the back cooking zones
automatically change back to their previously set heating levels.
TSE-N 05.00 A. B.
- 15 -
599 50 82 38
EN
Activate Warming Zone (C88900K)
1.
Touch the “Prepare” sensor field for approx. 2 seconds. A power indicator lights up in the sensor
field.
2.
Within 10 seconds, touch the sensor field “Activate”. The power indicator under the sensor field
“Prepare” goes out and the power indicator “Activate” under the sensor field lights up. The warming
zone is now switched on.
3.
To switch it off, touch the sensor field “Deactivate”. The power indica-tor under the sensor field
“Activate” goes out.
The warming zone can be used independent of the other cooking zones. The warming zone is
used to warm food.
Locking/Unlocking the Control Panel
The control panel (with the exception of the “On/Off” sensor field) can be locked at any required time
during cooking in order to prevent adju-stment of the settings e.g. caused by wiping over with a cloth.
This function is also useful as a child safety measure.
1.
Touch the button
until the indicator lamp lights up.
2.
To cancel the lock again, touch the lock button again until the indica-tor lamp goes out. Child
safety feature! If the cooking field is completely switched off by the “On/Off” sensor field when the
locking button is activated, the lok-king button is active when the cooking field is switched back on,
i.e. it is first necessary to touch the locking button so that the hobs can be switched back on again.
Timer
A cooking time can be set with the integrated timer for all 4 cooking zones. When the end of the cooking
time is reached, the cooking zone switches itself off automatically.
1.
Use the sensor field Cooking Zone to select the required cooking zone and set the required
cooking stage.
2.
Touch the TIMER
in the display.
TSE-N 05.00 A. B.
sensor field to activate the timer function for this cooking zone.
- 16 -
appears
599 50 82 38
EN
3.
Use the sensor fields
(e.g. 15 minutes).
or
to set or change the required duration until automatic switching-off
After a few seconds, the timer is started automatically and shows the time remaining until
switching-off. In addition, the display “Timer active” for the relevant cooking zone lights up, e.g. the
top left indicator lamp corresponds to the rear left cooking zone.
At the end of the cooking time set, the cooking zone switches off automatically and an acoustic
signal sounds.
4.
Touch the TIMER
sensor field to switch off the signal and indicator lamp.
For more rapid adjustment, leave your finger on the sensor field
or
until the required value is
reached. If the sensor field
is activated first, the time setting starts at 99 minutes. If the sensor field
is activated first, the time setting starts at 1 minute.
Displaying the Remaining Cooking Time
If you select a cooking zone which is in Timer mode, the cooking time still remaining appears in the
Timer display field.
Use the Timer as a Short Time Measurer (“Minute Minder”)
The Timer function can also be used as a short time measurer without the automatic switch-off function,
provided that the timer is not already being used for 1 or more cooking zones. No cooking zone may be
selected in this case. The sensor field cooking zone with the decimal point in the display must therefore
be touched again so that the deci-mal point goes out. Set the time as described above.
Ending the Timer Function Prematurely
There are two ways of switching off the timer early:
Switching off the cooking zone and timer simultaneously
1.
2.
Select the desired cooking zone using the cooking zone buttons.
Touch the
and
buttons simultaneously: cooking zone and timer switch off.
Switching off the timer - leaving the cooking zone active
1.
2.
3.
Select the desired cooking zone using the cooking zone buttons.
Touch the “Timer” button again.
Touch the
and
buttons simultaneously:
only the timer switches off.
The cooking zone is left on.
TSE-N 05.00 A. B.
- 17 -
599 50 82 38
EN
Cleaning and care
Advantages for cleaning and caring for the induction cooking zone
The cleaning effort for induction glass ceramic cooking surfaces is
considerably less than for cooking surfaces with radiant heating:
-
The induction cooking zone reacts faster to switching down and off. Boiling over and burning in of
dishes is avoided to a large degree.
-
The temperaturs on the glass ceramic surface are clearly lower with inductive cooking than with
the conventional radiant heating systems.
Since the heat is generated in the pan, food or foodstuffs possibly on the glass ceramic surface are not
burnt in as badly.
Glass ceramic cooking surface
It is important to clean the cooking surface after every use!
Attention! Never use aggressive cleaning agents such as, for example, coarse scouring cleaners or
scratching scouring pads.
Always clean the cooking surface when it is only a little dirty. Use a damp cloth and a little washing up
liquid. Then rub the cooking surface dry with a clean cloth. Remnants of cleaner must not be left on the
surface.
Clean the entire cooking surface thoroughly once a week. For cleaning use „Sidol-Edelstahlglanz“,
„Stahl-Fix“, „WK-Top“ or „Cillit“.
Then rinse the entire cooking surface with plain water and rub it dry
with a clean cloth. Please ensure that no residues (cleaner) remain on the surface. The coo-king
surface would otherwise be damaged!
TSE-N 05.00 A. B.
- 18 -
599 50 82 38
EN
Problem dirt
Residues from food that has boiled over
First soften these using a wet cloth and then remove residues using a glass or
razor blade scraper.
Danger! Take care not hurt yourself!
Then clean the cooking surface with the clea-ners identified above.
Burnt-in sugar, melted plastic you must remove immediately – while it is
still warm (not hot) – with a glass scraper otherwise damage can be incurred.
Then clean the cooking surface normally. You can prevent damages by sugar
or sugar-containing foods by caring for the cooking surface with „Collo-Profi“ or
„Cera-fix“.
Spots
Limescale stains, mother-of-pearl-like shiny stains, metallic iridiscent
discolourations, pan abrasions that have formed during coo-king can be
removed best while the cooking zones are still warm. Use one of the cleaners
mentioned above. If necessary repeat the cleaning process.
Danger!
Do not put vinegar, lemons or scale remo-vers on the hob frame, they will
make the surface matt. Grains of sand that have fallen on the coo-king
surface can cause scratches when the pans are slid around. Ensure, therefore,
that no grains of sand remain on the cooking surface.
Abraded decor
In time the decor is abraded by the use of aggressive cleaners and scouring
pan bases and dark stains develop.
You can obtain suitable cleaning and caring agents as well as glass
scrapers from the AEG customer service.
TSE-N 05.00 A. B.
- 19 -
599 50 82 38
EN
What to do if ...
... The letters
flashes in the digital display?
Check whether:
The pan is on the right cooking zone.
The diameter of the pan base is too small for the cooking zone!
The pan is suitable for induction cooking!
...
appears in the digital display?
-
Check whether the cooking zone could be overheated. For these checks turn the cooking zone off
and let it cool off. Try to switch the cooking zone on again after a few minutes with a suitable pan
on it.
The automatic switch-off feature for the cooking zone has responded. You can reactivate the
cooking zone by turning it quickly off and then on again.
-
Installationsinstructions
Attention!
The new unit may only be installed and connected by an approved specialist.
-
Repairs to the appliance are only to be carried out by approved ser-vice engineers. Improper
repairs can cause significant hazards for the user. If your appliance needs repairing, please
contact our customer service or your dealer.
Please follow these instructions, otherwise the warranty is void in the event of damages.
-
Flush-mounted units may only be operated following installation in suitable installation cabinets
and workplaces which conform to the relevant standards. This ensures sufficient protection against
contact for electrical units as required by VDE.
-
If your appliance malfunctions or if fractures, cracks or splits appear:
o
switch off all cooking zones,
o
switch off the fuse for the cooking surface or remove it.
TSE-N 05.00 A. B.
- 20 -
599 50 82 38
EN
Installation (C67100K and C6800K)
Installation (C88900K)
TSE-N 05.00 A. B.
- 21 -
599 50 82 38
EN
Installation
TSE-N 05.00 A. B.
- 22 -
599 50 82 38
EN
Technical data (C67100K)
Appliance Dimensions
Width
Depth
Height
Height inside
Cut-Out Dimensions
Width
Depth
Corner radius
Power Consumption
Radiant heat single ring cooking zone ø 145 mm
Radiant heat casserole zone ø 180 mm - ø 120 mm
Induction cooking zone ø 145 mm
Induction cooking zone ø 210 mm
Induction cooking zone ø 210 mm (P)
Heater Element Voltage
Total Electrical Load Max.
Technical data (C67100K)
Appliance Dimensions
Width
Depth
Height
Height inside
Cut-Out Dimensions
Width
Depth
Corner radius
Power Consumption
Induction cooking zone ø 145 mm
Induction cooking zone ø 180 mm
Induction cooking zone ø 180 mm (P)
Induction cooking zone ø 210 mm
Induction cooking zone ø 210 mm (P)
Heater Element Voltage
Total Electrical Load Max.
570 mm
500 mm
55 mm
52 mm
560 mm
490 mm
R3
1200 W
1700 W
1400 W
2200 W
3000 W
230 V ~
6.5 kW
570 mm
500 mm
55 mm
52 mm
560 mm
490 mm
R3
1400 W
1800 W
2300 W
2200 W
3000 W
230 V ~
7.2 kW
Technical data (C88900K)
Appliance Dimensions
Width
Depth
Height
Height inside
Cut-Out Dimensions
Width
Depth
Corner radius
Power Consumption
Induction cooking zone ø 145 mm
Induction cooking zone ø 180 mm
Induction cooking zone ø 180 mm (P)
Induction cooking zone ø 210 mm
Induction cooking zone ø 210 mm (P)
Warming zone
Heater Element Voltage
Total Electrical Load Max.
TSE-N 05.00 A. B.
761 mm
501 mm
55 mm
52 mm
750 +2 mm
490 +2 mm
R3
1400 W
1800 W
2300 W
2200 W
3000 W
120 W
230 V ~
7.32 kW
- 23 -
599 50 82 38
EN
Safety instructions for the installer
-
This hob must be installed by qualified personnel, according to the manufacturer’s instructions and
to the relevant country standards.
In respect of fire protection, this appliance corresponds to type Y (IEC 335-2-6). Only this type of
appliance may be installed with a high cupboard or wall on one side.
It is not permitted to fit drawers below the cooking surface.
Protection against electric shock must be provided by the installation.
The kitchen unit in which the appliance is fitted must satisfy the requirements of DIN 68930 in
respect of stability.
Built-in ovens and cooking surfaces are fitted with special connector systems. They may only be
combined with appliances with a matching system.
All cut surfaces are to be sealed with a suitable sealant for protection against moisture.
On tiled work surfaces, the joints in the area where the hob sits on the surface must be completely
filled with grout.
On natural, artificial stone, or ceramic tops, the snap action springs must be bonded in place.
Ensure that the seal is correctly seated in the frame and that it is sea-ted against the work surface
without leaving any gaps. Additional silicon sealant must not be applied, this will make removal
more difficult in the event of the need for service.
To remove the hob, it must be pressed out from below.
Electrical connection
Only the supply lead fitted on the recess may be used for connecting the unit. Replacement cables can
only be obtained from AEG customer service.
A fixture must be provided in the electrical installation which allows the appliance to be disconnected
from the mains at all poles with a contact opening width of at least 3 millimetres. Suitable isolation
devices include, e.g. cut-outs, fuses (screw type fuses are to be removed from the holder), earth leakage
trips and contactors.
Attention! Make the electrical connection in accordance with the con-nection diagram.
TSE-N 05.00 A. B.
- 24 -
599 50 82 38
EN
Additional information for the service
Cooktop assembly
-
The cooktop assembly conforms to the system of the New Range, i.e. the cooktop frame and the
cooktop glass are two separate parts and not stuck with each other.
-
After disassembling the cooktop take care that the 7-segment display and, with the self-sufficient
built-in cooktops, the control panel are not in the cooktop cover, but is clipped to the cooktop glass
from below.
Cooktop technology
-
With the twofold induction, the induction hot plates are front right and left, not laterally one after the
other as with the previous version. The induction module is a twofold module.
-
With the fourfold induction, the induction module consists of a block of four.
-
With this new series of induction cooktops there are no test points to check the electronic in case
of a malfunction. That means, if the reason for a hot plate, which does not function, is to be found
in a malfunction of the electronic, the only solution is to exchange the module or, with self-sufficient
built-in cooktops, to exchange the control panel. The modules can also not be checked with the
help of a test routine.
Compatibility
-
The induction cooktops can only be combined with ranges which are equipped with an ERM (modular energy regulator), from range series Compentence 2000 onward, classes Top and Comfort.
-
Concerning the compatibility of the control lines, these are directly compatible from Century
onward. With the previous range series Competence, the control line is equipped with an adaptor.
TSE-N 05.00 A. B.
- 25 -
599 50 82 38
EN
Cooktop assembly
4 Induction
TSE-N 05.00 A. B.
- 26 -
599 50 82 38
EN
TSE-N 05.00 A. B.
- 27 -
599 50 82 38
EN
Cooktop assembly
2 Induction
TSE-N 05.00 A. B.
- 28 -
599 50 82 38
EN
TSE-N 05.00 A. B.
- 29 -
599 50 82 38
EN
Download PDF

advertising