Avtech AVC798 User manual

H.264 Network DVR
User Manual
Please read instructions thoroughly before operation and retain it for future reference.
AV798(D)_797_796(D)_795_792(D)_CD541(D)_manual_V1.3
IMPORTANT SAFEGUARD
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION:
To reduce the risk of electric shock, do not expose this apparatus to rain or moisture. Only operate this
apparatus from the type of power source indicated on the label. The company shall not be liable for any
damages arising out of any improper use, even if we have been advised of the possibility of such damages.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
This exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
All lead-free products offered by the company comply with the requirements of the European law on the Restriction of Hazardous
Substances (RoHS) directive, which means our manufacture processes and products are strictly “lead-free” and without the
hazardous substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected separately at the
product end-of-life. This applies to your product and any peripherals marked with this symbol. Do not dispose of these products as
unsorted municipal waste. Contact your local dealer for procedures for recycling this equipment.
This apparatus is manufactured to comply with the radio interference requirements.
Disclaimer
The information in this manual was current when released. We reserve the right to revise or remove any content in this manual at any time. We
do not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of this manual. For the actual display
& operation, please refer to your DVR in hand. The content of this manual is subject to change without notice.
The product & company names mentioned herein may be the registered trademarks or tradenames of their respective owners.
Grounding
This is a Safety Class 1 Product (provided with a protective earthing ground incorporated in the power cord). The mains plug shall only be
inserted in a socket outlet provided with a protective earth contact. Any interruption of the protective conductor inside or outside of the instrument
is likely to make the instrument dangerous. Intentional interruption is prohibited.
Water & Moisture
Do not expose this product to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the product.
MPEG4 Licensing
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD
(“MPEG-4 VIDEO”) AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND
NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4
VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT
RELATING TO PROMOTIONAL INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE
HTTP://WWW.MPEGLA.COM.
GPL Licensing
This product contains codes which are developed by Third-Party-Companies and which are subject to the GNU General
Public License (“GPL”) or the GNU Lesser Public License (“LGPL”).
The GPL Code used in this product is released without warranty and is subject to the copyright of the corresponding
author.
Further source codes which are subject to the GPL-licenses are available upon request.
We are pleased to provide our modifications to the Linux Kernel, as well as a few new commands, and some tools to get
you into the code. The codes are provided on the FTP site, and please download them from the following site or you
can refer to your distributor:
ftp://ftp.dvrtw.com.tw/GPL/AV074/
Version
Video Viewer: 0119
TABLE OF CONTENTS
1. OVERVIEW............................................................................................................................... 1
1.1 Product Description .........................................................................................................................................1
1.2 Features...........................................................................................................................................................1
1.3 Specifications...................................................................................................................................................2
1.3.1 Models with DVD Writer.........................................................................................................................2
1.3.2 Models without DVD Writer....................................................................................................................3
1.4 Package Contents ...........................................................................................................................................4
2. FRONT AND REAR PANELS .................................................................................................. 5
2.1 Front Panel ......................................................................................................................................................5
2.2 Rear Panel.......................................................................................................................................................6
3. CONNECTIONS AND SETUP.................................................................................................. 8
3.1 SATA HDD Installation .....................................................................................................................................8
3.1.1 For 16CH& 8CH Models ........................................................................................................................8
3.1.2 For 4CH Models.....................................................................................................................................9
3.2 Camera Connection.......................................................................................................................................10
3.2.1 Regular Camera Connection ...............................................................................................................10
3.2.2 Speed Dome Camera Connection .......................................................................................................11
3.3 Power Setup ..................................................................................................................................................12
3.4 Date and Time Setting ...................................................................................................................................12
3.5 Password Setting...........................................................................................................................................13
4. BASIC OPERATION............................................................................................................... 14
4.1 Live Page.......................................................................................................................................................14
4.2 Recording ......................................................................................................................................................14
4.3 Playback ........................................................................................................................................................15
4.4 Key Lock and Unlock .....................................................................................................................................16
4.5 Upgrade .........................................................................................................................................................16
4.6 Search ...........................................................................................................................................................16
5. MAIN MENU ........................................................................................................................... 17
5.1 Menu Configuration .......................................................................................................................................17
5.2 Menu Operation Instruction............................................................................................................................17
6. QUICK START MENU ............................................................................................................ 18
6.1 Status.............................................................................................................................................................18
6.2 Manual Record ..............................................................................................................................................19
6.3 Timer..............................................................................................................................................................20
6.4 Date ...............................................................................................................................................................21
7. ADVANCED MENU ................................................................................................................ 23
7.1 Advanced Configuration.................................................................................................................................23
7.1.1 Camera................................................................................................................................................23
7.1.2 Detection .............................................................................................................................................24
7.1.3 Alert .....................................................................................................................................................25
7.1.4 Network ...............................................................................................................................................26
7.1.5 SNTP ...................................................................................................................................................28
7.1.6 Display.................................................................................................................................................29
7.1.7 Record .................................................................................................................................................29
7.1.8 Remote ................................................................................................................................................30
7.2 System Info....................................................................................................................................................31
7.3 Event Info.......................................................................................................................................................32
7.3.1 Quick Search .......................................................................................................................................33
7.3.2 Event Search .......................................................................................................................................33
7.3.3 HDD Info..............................................................................................................................................34
7.3.4 Event Log ............................................................................................................................................34
7.4 Backup...........................................................................................................................................................34
7.4.1 USB BACKUP .....................................................................................................................................35
7.4.2 DISK BACKUP (Selected Models Only) ..............................................................................................36
8. REMOTE OPERATION .......................................................................................................... 38
8.1 Supplied Licensed Software ..........................................................................................................................38
8.1.1 Installation & Network Connection .......................................................................................................38
8.1.2 Control Panel Overview .......................................................................................................................39
Simplified Version (Default) ...................................................................................................................39
Full Function Version .............................................................................................................................40
Main Button Overview ...........................................................................................................................40
8.1.3. General Operation ..............................................................................................................................41
Record...................................................................................................................................................41
Playback................................................................................................................................................41
Network Backup ....................................................................................................................................42
8.1.4. E-Map .................................................................................................................................................43
How to Add an E-Map Group.................................................................................................................43
How to Edit / Remove an Existing E-Map Group ...................................................................................45
8.2 IE Web Browser .............................................................................................................................................48
8.3 Quick Timer Player ........................................................................................................................................50
APPENDIX 1 PIN CONFIGURATION ........................................................................................ 51
APPENDIX 2 COMPATIBLE USB FLASH DRIVE BRAND....................................................... 54
APPENDIX 3 COMPATIBLE HDD BRAND................................................................................ 55
APPENDIX 4 TROUBLESHOOTING ......................................................................................... 56
APPENDIX 5 RS485 PROTOCOL ............................................................................................. 57
APPENDIX 6 DVR BATTERY REPLACEMENT ........................................................................ 58
APPENDIX 7 RECORDING TIME TABLE ................................................................................. 59
APPENDIX 8 DVD WRITER INSTALLATION ............................................................................ 60
OVERVIEW
1. OVERVIEW
1.1 Product Description
This H.264 DVR series greatly maximizes the video quality and minimizes the file size (expand the storage
capacity) with the feature of H.264 video compression technology. To quickly backup, the DVD writer (optional) and
USB port are built in for your convenience, or the network backup is also available. It also supports the connection to
the SATA HDD & keyboard controller for your easy operation.
1.2 Features
H.264 Video Compression Technology
‧ At the local site, the file size is minimized and the record time is lengthened
‧ At the remote site, with the features of small file size and low bit rate, it will be more adaptive to different kinds of
network environment compared with conventional codec designs
VGA Support
‧ For Model 1, 2, 3, 4, 6 & 8: VGA interface built-in with output resolution up to 1600 x 1200
‧ For Model 5 & 7: Optional VGA converter needed for VGA output
Graphical & Multi-language OSD
Remote Independent Operation
‧ Allows single-channel viewing of live displays without changing display settings on the licensed software AP
provided
Free Upgrade to Advanced Functions
‧ Allows you to upgrade DVR functions without any charges
Multiplex Operation
‧ Allows live display, record, playback, backup, and network operations at the same time
Excellent Image Quality and Performance
‧ The CIF image quality is excellent for clear and detailed image
Intelligent Motion Trigger Recording
‧ Customizable security settings are achieved with the advanced motion detection, the scheduled motion detection
recording, and the quick search function
‧ Supports pre-alarm recording (8MB)
‧ Activates event recording automatically when an alarm is triggered, and sends a http link with the event snapshot to
the designated e-mails / FTP address (Selected models only)
Backup Devices
‧ Supports USB 2.0 flash drive, DVD writer (optional), and network
Remote Surveillance
‧ Supports remote surveillance up to 20 users simultaneously with the licensed software “Video Viewer”, Internet
Explorer / Mozilla Firefox web browser, and QuickTime player.
Covert Recording
‧ Blank screen replaces live displays to achieve covert recording
Audio Support
‧ For Model 1, 2, 4 & 6: Supports 4 audio-in, 2 audio-out to record soundsFor Model 3 & 8: Supports 4 audio-in, 1 audio-out to record sounds
For Model 5 & 7: Supports 1 audio-in, 1 audio-out to record sounds
General
‧
‧
‧
‧
‧
Supports SATA HDDs
Supports IR remote controller and keyboard controller
System auto recovery after power failure
Supports PTZ camera operations through RS-485, and PTZ Hot Point function
Supports daylight saving function
-1-
OVERVIEW
‧ Supports manual / timer / motion / network recording
‧ Supports TCP/IP, PPPoE, DHCP and DDNS network connection.
1.3 Specifications
1.3.1 Models with DVD Writer
MODEL
Model 1
Model 2
Model 3
Video System
Video Compression Format
Video Input
16 Channels
8 Channels
4 Channels
Video Loop Output
16 Channels
8 Channels
4 Channels
(Composite video signal 1 Vp-p 75Ω BNC)
(Composite video signal 1 Vp-p 75Ω BNC)
Video Output (BNC)
NTSC / PAL (auto detection)
H.264
Main Monitor
Output
Call Monitor
Output
Video Output (VGA)
(up to 1600 x 1200)
Audio Input
Audio Output
Multiplex Operating
Maximum Recording Rate (Frame)
Maximum Recording Rate (Field)
Maximum Recording Rate (CIF)
Recording Mode
Recording Quality Options
Pre-alarm Recording
HDD Type
HDD Storage
* HDDs are optional
** Supports up to 1TB per HDD
For stable display
For sequence display
Built-in VGA output for LCD monitor
4 Channels (Mono)
4 Channels (Mono)
2 Channels (Mono)
1 Channel (Mono)
Supports live display, record, playback, backup, and network simultaneously
30 IPS @ 704×480 <NTSC>
120 IPS @ 704×480 <NTSC>
60 IPS @ 704×480 <NTSC>
25 IPS @ 704×576 <PAL>
100 IPS @ 704×576 <PAL>
50 IPS @ 704×576 <PAL>
240 IPS @ 720×240 <NTSC>
200 IPS @ 720×288 <PAL>
480 IPS @ 360×240 <NTSC>
400 IPS @ 360×288 <PAL>
Accommodates up to two SATA HDDs
Accommodates one SATA HDD
--
Delete HDD Data Efficiently
(1TB within 2 seconds)
HDD Quick Cleaning
Quick Search
USB Flash Drive Backup
DVD Writer Backup
Network Transfer Format
Ethernet
Network Protocol
Network Surveillance Interface
Remote Independent Operation
Network Alarm Notification
CMS (Central Management System)
R.E.T.R. (Remote Event Trigger
Recording)
Operating System for Network
Function
IR Remote Control
Multilingual OSD
Motion Detection Area
Motion Detection Sensitivity
PTZ Control
External Alarm
Picture Zoom
Key Lock (Password Protection)
Video Loss Detection
Camera Title
Video Adjustable
Date Display Format
Daylight Saving
Power Source (±10%)
Power Consumption
120 IPS @ 704×240 <NTSC>
60 IPS @ 704×240 <NTSC>
100 IPS @ 704×288 <PAL>
50 IPS @ 704×288 <PAL>
120 IPS @ 352×240 <NTSC>
240 IPS @ 360×240 <NTSC>
100 IPS @ 352×288 <PAL>
200 IPS @ 360×288 <PAL>
Manual / Timer / Motion / Alarm / Remote
Super Best, Best, High & Normal
YES (8 MB)
SATA
Time / Motion / Alarm
YES
YES
H.264
10/100 Base-T.
TCP/IP, PPPOE, DHCP and DDNS (Dynamic IP)
Licensed Software “Video Viewer” / Internet Explorer & Firefox web browser / QuickTime
(20 users on-line simultaneously)
YES
E-mail and FTP server
YES (Maxmium: 16 different IP addresses)
NO
YES
Windows Vista / XP / 2000; Apple Mac
16 inputs, 1 output
YES
YES
16 × 12 grids per channel
4 adjustable parameters for accurate detection
Pelco-D / Pelco-P / our own protocol
8 inputs, 1 output
2X digital zoom (live & playback)
YES
YES
Supports up to 6 letters
Hue / Color / Contrast / Brightness
YY/MM/DD, DD/MM/YY, MM/DD/YY
YES
DC 19V
＜64 W
-2-
4 inputs, 1 output
< 42 W
OVERVIEW
MODEL
Model 1
Operating Temperature
Dimensions (mm)**
System Recovery
Optional Peripherals
Model 2
Model 3
0℃ ~ 40℃ (32℉~104℉)
432(W) × 90(H) × 326(D)
System auto recovery after power failure
Keyboard controller
10℃ ~ 40℃ (50℉~104℉)
375(W) × 61(H) × 281(D)
* The specifications are subject to change without notice.
1.3.2 Models without DVD Writer
MODEL
Model 4
Video System
Video Compression Format
Video Input
(Composite video signal 1 Vp-p 75Ω BNC)
Video Loop Output
(Composite video signal 1 Vp-p 75Ω BNC)
Video Output (BNC)
Main Monitor
Output
Call Monitor
Output
Video Output (VGA)
(up to 1600 x 1200)
Audio Input
Audio Output
Multiplex Operating
Maximum Recording Rate (Frame)
Maximum Recording Rate (Field)
Maximum Recording Rate (CIF)
Recording Mode
Model 5
Model 6
16 Channels
16 Channels
8 Channels
--
8 Channels
Network Transfer Format
Ethernet
Network Protocol
Network Surveillance Interface
Remote Independent Operation
Network Alarm Notification
CMS (Central Management System)
R.E.T.R. (Remote Event Trigger
Recording)
Operating System for Network
Function
IR Remote Control
Multilingual OSD
Motion Detection Area
--
4 Channels
For sequence
For sequence
For sequence
--display
display
display
Built-in VGA
Built-in VGA
Built-in VGA
output for LCD
-output for LCD
-output for LCD
monitor
monitor
monitor
4 Channels
4 Channels
4 Channels
1 Channel (Mono)
1 Channel (Mono)
(Mono)
(Mono)
(Mono)
2 Channels
2 Channels
1 Channel (Mono)
1 Channel (Mono)
1 Channel (Mono)
(Mono)
(Mono)
Supports live display, record, playback, backup, and network simultaneously
30 IPS @
120 IPS @ 704×480 <NTSC>
60 IPS @ 704×480 <NTSC>
704×480 <NTSC>
25 IPS @
100 IPS @ 704×576 <PAL>
50 IPS @ 704×576 <PAL>
704×576 <PAL>
240 IPS @
120 IPS @
60 IPS @
--720×240 <NTSC>
704×240 <NTSC>
704×240 <NTSC>
200 IPS @
100 IPS @
50 IPS @
--720×288 <PAL>
704×288 <PAL>
704×288 <PAL>
120 IPS @
480 IPS @ 360×240 <NTSC>
240 IPS @ 360×240 <NTSC>
352×240 <NTSC>
100 IPS @
400 IPS @ 360×288 <PAL>
200 IPS @ 360×288 <PAL>
352×288 <PAL>
Manual / Timer /
Manual / Timer /
Manual / Timer /
Manual / Timer /
Manual / Timer /
Motion / Alarm /
Motion / Alarm /
Motion / Alarm /
Motion
/
Remote
Motion
/
Remote
Remote
Remote
Remote
Super Best, Best, High & Normal
YES (8 MB)
SATA
Accommodates up to two SATA HDDs
HDD Quick Cleaning
DVD Writer Backup
4 Channels
For stable display
* HDDs are optional
** Supports up to 1TB per HDD
USB Flash Drive Backup
Model 8
NTSC / PAL (auto detection)
H.264
Recording Quality Options
Pre-alarm Recording
HDD Type
HDD Storage
Quick Search
Model 7
Delete HDD Data
Efficiently (1TB
within 2 seconds)
Time / Motion /
Alarm
-Time / Motion /
Alarm
Time / Motion /
Time / Motion
Alarm
YES
Available for self
Available for self
--installation
installation
H.264
10/100 Base-T.
TCP/IP, PPPOE, DHCP and DDNS (Dynamic IP)
Licensed Software “Video Viewer” / Internet Explorer & Firefox web browser / QuickTime
(20 users on-line simultaneously)
YES
E-mail and FTP
E-mail and FTP
E-mail and FTP
--server
server
server
YES (Maxmium: 16 different IP addresses)
Time / Motion
NO
YES
Windows Vista / XP / 2000; Apple Mac
YES
YES
16 x 12 grids per
channel
3 pre-defined
detection areas
selectable
-3-
16 x 12 grids per
channel
3 pre-defined
detection areas
selectable
16 x 12 grids per
channel
OVERVIEW
MODEL
Motion Detection Sensitivity
PTZ Control
External Alarm
Picture Zoom
Key Lock (Password Protection)
Video Loss Detection
Camera Title
Video Adjustable
Date Display Format
Daylight Saving
Power Source (±10%)
Power Consumption
Model 4
4 adjustable
parameters for
accurate detection
16 inputs, 1 output
Model 5
Model 6
One parameter
One parameter
with three
4 adjustable
with three
sensitivity levels
parameters for
sensitivity levels
(High / Normal /
accurate detection
(High / Normal /
Low)
Low)
Pelco-D / Pelco-P / our own protocol
-8 inputs, 1 output
-2X digital zoom (live & playback)
YES
YES
Supports up to 6 letters
Hue / Color / Contrast / Brightness
YY/MM/DD, DD/MM/YY, MM/DD/YY
YES
DC 19V
＜64 W
Operating Temperature
0℃ ~ 40℃ (32℉~104℉)
Dimensions (mm)**
432(W) × 90(H) × 326(D)
System Recovery
Optional Peripherals
Keyboard
controller
Model 7
System auto recovery after power failure
Keyboard
Keyboard
Keyboard
controller / VGA
controller
/ VGA
controller
Converter
Converter
* The specifications are subject to change without notice.
1.4 Package Contents
□
□
□
□
□
Digital video recorder (DVR)
Adapter and power cord
quick start & IR remote control manual
CD-ROM (including manual & licensed software “Video Viewer”)
IR receiver (optional)
□
□
□
□
HDD bracket screws (spare parts)
DSUB PIN connector
IR remote controller
AAA size battery * 2
Note: Before using the IR remote control, please install the batteries first.
-4-
Model 8
4 adjustable
parameters for
accurate detection
4 inputs, 1 output
< 42 W
10℃ ~ 40℃ (50
℉~104℉)
375(W) × 61(H) ×
281(D)
Keyboard
controller
FRONT AND REAR PANELS
2. FRONT AND REAR PANELS
2.1 Front Panel
1)
LED Indicators
HDD is reading or recording.
DVR is powered on.
An alarm is triggered.
Timer recording is on.
Under playback status (For 4CH model only).
HDD is full (For 16CH / 8CH models only).
2)
MENU
Press “MENU” to enter the main menu.
3)
ENTER
Press “ENTER” to confirm the setting.
4)
SLOW
Under the playback mode, press “SLOW“ to show slow playback.
5)
ZOOM
Press “ZOOM” to enlarge the picture of selected channel in the FRAME or FIELD recording mode.
6)
Press “
7)
“ to show the 4 channel display mode.
SEQ
Press “SEQ” to activate the call monitor function and press “SEQ” again to escape the call monitor mode.
8)
POWER
Press to turn on / off the DVR.
(Under the recording mode, please stop recording before turning off the DVR).
9)
CH1 ~ 16 / CH1 ~ 8 / CH1 ~ 4
Press the channel number buttons to select the channel to display.
10) PLAY
Press to playback the recorded data.
11) ▲ (PAUSE/+) / ▼ (STOP/-) / ◄ (REW) / ► (FF)
Press ▲ / ▼ / ◄ / ► to move the cursor up / down / left / right.
Under the playback mode, press “ PAUSE” to pause playback.
Under the playback mode, press “ STOP” to stop playback.
Under the playback mode, press “FF“ to fast forward.
Under the playback mode, press “REW“ to fast rewind.
-5-
FRONT AND REAR PANELS
12) AUDIO (SLOW + ZOOM)
Press “SLOW” + “ZOOM” to select live or playback sounds of the audio channels.
Live audio of the 1st audio channel
Playback audio of the 1st audio channel
Live audio of the 2nd audio channel
Playback audio of the 2nd audio channel
Live audio of the 3rd audio channel
Playback audio of the 3rd audio channel
Live audio of the 4th audio channel
Playback audio of the 4th audio channel
The audio channel is not selected.
13) P.T.Z. (
+ SEQ)
Press “ ” + “SEQ” at the same time to enter / exit the PTZ control mode.
In the PTZ control mode,
* Zoom in: Press "SEQ"
* Zoom out: Press " "
* Adjust PTZ angle: Press ▲ / ▼ / ◄ / ►
14) LIST (Event List Search)
To quick search the recorded files by event, press to show all types of the event lists.
15) SNAP
Press “SNAP” to take a snapshot.
Note: Before taking a snapshot, insert a compatible USB flash drive into the DVR USB port for snapshot
saving. For the compatible USB flash drive list, please refer to “APPENDIX 2 COMPATIBLE USB
FLASH DRIVE BRAND” at page 54.
16) REC (For 16CH & 8CH Models Only)
Press “REC” to start manual recording function immediately when this function is disabled.
17) EJECT (For Selected Models Only)
Press “EJECT” to open / close the DVD Writer.
18) USB
Supports firmware / OSD upgrade and file backup.
2.2 Rear Panel
1)
75Ω / HI-IMPEDANCE
When using Loop function, please switch to HI-IMPEDANCE. When you don’t use Loop function, please switch to
75Ω.
2)
INPUT (1 ~ 16 / 1 ~ 8 / 1 ~ 4): Connect to video sources, such as cameras.
LOOP (1 ~ 16 / 1 ~ 8 / 1 ~ 4): Video output connector. (For Selected Models Only)
Note: The DVR will automatically detect the video system of the camera, please make sure that the
cameras are properly connected to the DVR and power-supplied before the DVR is turned on.
3)
MONITOR
Connect to a CRT monitor for video output.
4)
CALL (For Selected Models Only)
Connect to a call monitor.
5)
Audio IN
Connect to audio sources, such as cameras equipped with the audio function.
-6-
FRONT AND REAR PANELS
When users start recording, the audio input will also be recorded with corresponding video channel.
Note: To make a video backup with audio, make sure the camera which supports the audio function is
connected to the correct video channel (INPUT) which supports audio recording. Depending on
the model you have, up to four channels for audio recording are supported.
Take Model 1 as an example,
Audio IN 1 audio data will be recorded with CH1 video.
Audio IN 2 audio data will be recorded with CH2 video.
Audio IN 3 audio data will be recorded with CH3 video.
Audio IN 4 audio data will be recorded with CH4 video.
6)
Audio OUT
Connect to a monitor or speaker with 1 mono audio output.
7)
VGA (For Selected Models Only)
Connect to a LCD monitor directly.
8)
IR
Connect the IR receiver extension line (optional) for remote control.
9)
RS485 (For 16CH & 8CH Models Only)
Connect to external devices (such as speed dome cameras) with RS485-A and RS485-B wires.
10) EXTERNAL I/O (For Selected Models Only)
Insert the supplied 15 / 25 PIN DSUB to this port for connecting external devices (external alarm, etc).
For detailed I/O port PIN configuration, please refer to “APPENDIX 1 PIN CONFIGURATION” at page 51.
11) LAN
Connect to Internet by LAN cable.
12) LINK / ACT LED light:
When the Internet is activated, the LED light will be on.
13) DC 19V
Connect to the supplied adapter.
-7-
CONNECTIONS AND SETUP
3. CONNECTIONS AND SETUP
Note: The DVR is designed to automatically detect the video system of the connected cameras (NTSC or
PAL). To make sure the system detection is correct, please check if the cameras are connected to
the DVR and power-supplied before the DVR is powered on.
3.1 SATA HDD Installation
The SATA HDDs must be installed before the DVR is powered on.
3.1.1 For 16CH& 8CH Models
STEP1: Remove the screws on the top cover of DVR, and remove the top cover.
With the front panel facing you, there are two HDD brackets: one is on the left, and the other one is at the
middle.
STEP2: Install the compatible HDD to the bracket.
2.1. To install the HDD on the left:
a) With the PCB side facing up, connect the compatible HDD to the power connector and data bus
connector.
b) Put the compatible HDD in the left bracket, and fasten it with the supplied screws, two for each side.
2.2. To install the HDD at the middle:
a) Remove the bracket.
b) With the PCB side facing up, slide the HDD into the HDD bracket.
c) Fix the HDD with the supplied screws to the bracket, two for each side.
STEP3: Connect the compatible HDD to the power connector and data bus connector.
STEP4: Replace the bracket back to the DVR.
STEP5: Replace the top cover and fasten the screws you loosened in STEP1.
-8-
CONNECTIONS AND SETUP
3.1.2 For 4CH Models
Note: The following description takes a 4CH DVR model WITHOUT a DVD writer built-in as an example.
For the 4CH DVR model with a DVD writer built-in, please ignore STEP2.1.
STEP1: Remove the screws on the top cover of DVR, and remove the top cover.
There are two places to install HDDs for this DVR: one is on the right, and the other one is on the left.
STEP2: Turn the DVR real panel facing you.
2.1. To install the HDD on the right (For the DVR model without a DVD writer built-in only):
a) Find the two HDD brackets in the accessory pack, and fix them onto the DVR base.
b) Get a compatible SATA HDD, and connect it to the power connector and data bus connector.
c) Put the HDD to the DVR, and have the SATA HDD fixed in the DVR.
2.2. To install the HDD on the left side:
a) Remove the HDD bracket as indicated below.
-9-
CONNECTIONS AND SETUP
b) Get a compatible SATA HDD. Slide the HDD to the bracket, and fix it with two screws for each side.
There are three screw holes per side on the bracket, and you can choose two of them to secure the
HDD.
c) Connect the HDD to the power connector and data bus connector.
d) Screw the HDD bracket back to the DVR base.
STEP3: Replace the top cover and fasten the screws you loosened in STEP1.
3.2 Camera Connection
The cameras must be connected and power-supplied before the DVR is turned on. Connect the camera with the
indicated power supply. And then connect the camera video output to the DVR video input port with a coaxial cable or
RCA lines with BNC connectors (The DVR will automatically detect the video system of the camera).
Note: For detailed DVR video input / output ports, please refer to “2.2 Rear Panel” at page 6.
For detailed camera operation, please refer to its own manual.
3.2.1 Regular Camera Connection
1)
Video cable connection
Connect the camera video output to the DVR video input port with a coaxial cable or RCA line with BNC
connector.
2)
Audio cable connection (Optional)
Connect the camera audio output to the DVR audio input port with a coaxial cable or RCA line with BNC
connector.
-10-
CONNECTIONS AND SETUP
3)
Power connection
Connect the camera with indicated power supply and make sure it’s power-supplied.
3.2.2 Speed Dome Camera Connection
The following description is taking our brand’s speed dome camera as an example. For detailed PIN / port
connection, please refer to “APPENDIX 1 PIN CONFIGURATION” at page 51; for DVR setting to control the speed
dome camera, please refer to “7.1.8 Remote” at page 30.
RJ11 cable
RS485-A: Red wire
RS485-B: Green wire
The RJ11 cable is not supplied in the sales package.
15 PIN D-Sub Connector
RS-485 Port
RS485-A: PIN 11
RS485-B: PIN 10
RS485-A: PIN 2
RS485-B: PIN 3
Solder Side of
15-pin D-Sub connector
RS485 -A: PIN11 / RS485-B: PIN1 0
8
7
15 14
16
6
5
13
4
12
3
11
2
1
10
9
17
D-Sub connector is supplied with the DVR package.
Example of RS485 port on the DVR rear panel.
STEP 1: Get a RJ11 cable with the proper length to your connection.
Different RJ11 connector may have different wire layout, so the connection might be different. If you
cannot control the DVR after connection, please reverse the RJ11 cable connection with the DVR.
STEP 2: Remove one end of the insulating coating of the RJ11 cable.
Remove one end of the insulating coating of the RJ11 cable to find the RS485-A and the RS485-B wires,
and remove the insulating coating to reveal the naked wires for further connection.
STEP 3: Twist the RS485-A and RS485-B wires of the RJ11 cable and the speed dome camera together.
Twist the RS485-A (red) and RS485-B (green) wires of the RJ11 cable to the RS485-A (brown) and
RS485-B (orange) wires of the speed dome camera. To protect the naked wires, use the insulation tape
to cover on the twisted wires.
STEP 4: Connect the other end of the RJ11 cable to DVR.
When there’s an RS485 port on the DVR real panel
Connect the other end of the RJ11 cable without removing the insulating coating directly to the RS485
port on the DVR real panel.
When there’s an external I/O port on the DVR real panel
Solder the RS485-A (red) and RS485-B (green) wires of the RJ11 cable to the corresponding pins on the
solder side of the 15 PIN D-Sub connector (as shown in the picture above).
-11-
CONNECTIONS AND SETUP
STEP 5: Set the speed dome camera at the DVR side.
Go to “ADVANCE” l “REMOTE” to set the speed dome camera.
a) Select the device to “PTZ”.
b) Set the ID to the value the same as the one set in the speed dome camera. The default ID of the
camera is 000.
c) Select the protocol to “NORMAL”.
d) Set the baud rate to the value the same as the one set in the speed dome camera. The default baud
rate of the camera is 2400.
REMOTE
TITLE
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
NEXT
DEVICE
PTZ
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
ID
000
000
000
000
000
000
000
000
000
000
PROTOCOL
NORMAL
NORMAL
NORMAL
NORMAL
NORMAL
NORMAL
NORMAL
NORMAL
NORMAL
NORMAL
RATE
2400
2400
2400
2400
2400
2400
2400
2400
2400
2400
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
3.3 Power Setup
This device should be operated only with the type of power source indicated on the manufacturer’s label. Connect
the indicated AC power cord to the power adapter, and plug into an electrical outlet. The power LED will be on.
Note: Before the DVR is powered on, make sure the cameras are connected and power-supplied for the
detection of the camera video system to be correct.
Note: To ensure that your DVR works constantly and properly, it's recommended to use an UPS,
Uninterruptible Power Supply (Optional), for continuously operation.
3.4 Date and Time Setting
Before operating your DVR, please set the date and time on your DVR FIRST.
Note: Please DO NOT change the date or time of your DVR after the recording function is activated.
Otherwise, the recorded data will be disordered and you will not be able to find the recorded file
to backup by time search. If users change the date or time accidentally when the recording
function is activated, it’s recommended to clear all HDD data, and start recording again.
Note: For the first time to use the DVR, please power it on for at least 48 hours continuously after the
date & time is set correctly. It helps to prevent DVR time from resetting after the disconnecting of
DVR power. If the DVR time resets after the disconnecting of DVR power, for example, caused by
a power outage, the battery might run out and please replace the battery as described in
“APPENDIX 6 DVR BATTERY REPLACEMENT” at page 58.
Press “MENU” and enter the password to go to the quick-start menu list. The default admin password is 0000.
-12-
CONNECTIONS AND SETUP
Move to the icon
and you can set the date / time / daylight saving in this menu list.
CHANNEL TITLE
EVENT STATUS
DATE DISPLAY
ADVANCE
QUICK START
ON
ON
ON
IMAGE SIZE
QUALITY
IMAGE PER SECOND
CIF
BEST
120
RECORD TIMER
DETECTION TIMER
OFF
OFF
DATE
FORMAT
DAYLIGHT SAVING
2008 / APR / 23
Y/M/D
OFF
uv SELECT
s BACK
t NEXT
11 : 20 : 45
ENTER
3.5 Password Setting
Press “MENU” and enter the password to go to the quick-start menu list. Then, move to “ADVANCE” to enter the
advanced setting menu.
In the “ADVANCE” menu, move to “
” (SYSTEM INFO). Select “PASSWORD” and press “ENTER” to enter the
submenu to set the password (four digits).
SYSTEM INFO
SERIAL TYPE
BAUD RATE
HOST ID
PASSWORD
RESET DEFAULT
CLEAR HDD
UPGRADE
R.E.T.R. (MIN) (Selected models only)
AUTO KEYLOCK (SEC)
LANGUAGE
VIDEO FORMAT
VERSION
RS485
2400
0
XXXX
RESET
HDD-MASTER-1
START
05
NEVER
ENGLISH
PAL
1083-1028-1009-1013-02-0000
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
-13-
BASIC OPERATION
4. BASIC OPERATION
4.1 Live Page
In this live page of the DVR, you can see the live viewing of 1- / 4- / 9- / 16-cut screen.
Icon Function
Icon
Function
Icon
Function
Icon
st
Function
The 2nd live audio
channel
Key lock
Key unlock
The 1 live audio
channel
The 3rd live audio
channel
The 4th live audio
channel
The 1st playback
audio channel
The 2nd playback
audio channel
The 3rd playback
audio channel
The 4th playback
audio channel
Audio channel
unselected
Digital zoom mode
Digital zoom
unselected
Timer recording
Motion
Recording
R.E.T.R. ON
R.E.T.R. Delay
(Selected models only)
(Selected models only)
Alarm
(Selected models only)
HDD overwrite
4.2 Recording
When the HDD overwrite function is activated, this device will overwrite 8GB data from the oldest for continuous
recording without notice.
1)
Continuous Recording Icon
By defaults, the record icon (
2)
) shows on the screen when the DVR is powered on and a HDD is installed.
Event Recording Icon
When the motion detection or alarm is activated, the motion icon (
any motion or alarm event.
3)
) or alarm icon (
) shows on the screen for
Timer Recording Icon
When the timer record is activated, you will see the icon “
” (timer) on the screen.
Note: A new log will be added in the system log when the HDD data is overwritten or the recording starts
after DVR reboots.
4)
HDD Overwritten Icon
The HDD overwritten function can be set to ON / OFF. When this function is enabled (ON), the
the screen.
-14-
icon will display on
BASIC OPERATION
4.3 Playback
Press “PLAY” on the DVR control panel, and the device will playback the latest recorded video.
Note: There must be at least 8192 images of recorded data for playback to work properly. If not, the
device will stop playback. For example, if the IPS is set to 30, the recording time should be at least
273 seconds (8192 images / 30 IPS) for the playback to work properly.
Note: The playback at the local site might not be so smooth if there’s any remote surveillance
simultaneously going on.
1)
Fast Forward / Fast Rewind
You can increase the speed for fast forward and rewind on this device. In the playback mode:
Press “FF” once to get 4X speed forward and press twice to get 8X speed, etc. And the maximum speed is 32X.
Press “REW” once to get 4X speed rewind and press twice to get 8X speed, etc. And the maximum speed is 32X.
Note: During playback, the image size of the recording (FRAME, FIELD or CIF) will be shown on the
screen.
2)
Pause / Image Jog
Press “PAUSE” to pause the playback.
In the Pause mode:
Press “FF” once to get one frame forward.
Press “REW” once to get one frame rewind.
3)
Stop
Press “STOP” under playback mode, and the screen will return to live monitoring mode.
4)
Slow Playback
Press “SLOW” to get 1/4X speed playback and press twice to get 1/8X speed playback.
5)
Audio Playback (SLOW + ZOOM)
Press “SLOW” + “ZOOM” to select the live or playback sound of the audio channels.
Live audio of the 1st audio channel
Playback audio of the 1st audio channel
Live audio of the 2nd audio channel
Playback audio of the 2nd audio channel
Live audio of the 3rd audio channel
Playback audio of the 3rd audio channel
Live audio of the 4th audio channel
Playback audio of the 4th audio channel
The audio channel is not selected.
Note: To make a video backup with audio, make sure the camera which supports the audio function is
connected to the correct video channel (INPUT) which supports audio recording. Depending on
the model you have, up to four channels for audio recording are supported.
Take Model 1 as an example,
Audio IN 1 audio data will be recorded with CH1 video.
Audio IN 2 audio data will be recorded with CH2 video.
Audio IN 3 audio data will be recorded with CH3 video.
Audio IN 4 audio data will be recorded with CH4 video.
-15-
BASIC OPERATION
4.4 Key Lock and Unlock
1)
Key Lock On
Set the time-out after which the key lock function is activated (NEVER / 10 SEC / 30 SEC / 60 SEC). Please refer
to “7.2 System Info” at page 31.
OR
Press “F2” on the IR remote controller to immediately lock the keys.
2)
Key Lock Off
Enter the DVR password to exit “Key Lock” mode.
Note: For the password setting, please refer to “3.5 Password Setting” at page 13.
4.5 Upgrade
‧ Firmware / Multilanguage OSD Upgrade
1)
By using USB flash drive
Step 1. Format the USB memory device as FAT 32 format first.
Step 2. Get the upgrade files from your distributor, and save the upgrade files in your USB flash device (do not
change the file name).
Step 3. Insert your USB flash drive into the USB port. Wait till the DVR detects your USB flash drive.
Step 4. Press “MENU”, and move to “ADVANCE” l “
” (SYSTEM INFO). Select “UPGRADE” l “START”, and
press “ENTER”.
Step 5. Select “YES”, and press “ENTER” to confirm the upgrade.
2)
By using the supplied software “Video Viewer”
Step 1. Save the upgrade files at your PC (do not change the file name), and execute Video Viewer.
Step 2. In the “Address Book” panel, select the IP address of your DVR (or add the IP address of your DVR to the
address book if it’s not yet in the address book), and click “
” to show the “Update Server” panel.
Step 3. In “Update Server”, click “Firmware” or “Language” tab as needed, and click “Add” to select the firmware
or OSD files to upgrade.
Step 4. Click “Update Firmware” or “Update Language” to start the upgrade.
4.6 Search
1)
Search by List
Press “LIST” on the DVR control panel to show the list for all types of the recorded files. Choose the item you
want to view, and press “ENTER” to start playback.
2)
Search by Time
In the “
” (EVENT INFO) menu list, move to “QUICK SEARCH”, and press “ENTER” to enter the quick search
menu. You can search any specific events by time (Year / Month / Day / Hour / Min) and directly play the file you
find.
-16-
MAIN MENU
5. MAIN MENU
5.1 Menu Configuration
CHANNEL TITLE
EVENT STATUS
DATE DISPLAY
IMAGE SIZE
QUALITY
IMAGE PER SECOND
RECORD TIMER
DETECTION TIMER
DATE
FORMAT
DAYLIGHT SAVING
STATUS
RECORD
QUICK START MENU
TIMER
DATE
ADVANCE CONFIG
ADVANCED MENU
SYSTEM CONFIG
EVENT LOG
CAMERA
DETECTION
ALERT
NETWORK
SNTP
DISPLAY
RECORD
REMOTE
SERIAL TYPE
BAUD RATE
HOST ID
PASSWORD
RESET DEFAULT
CLEAR HDD
UPGRADE
R.E.T.R. (MIN) (Selected Models Only)
AUTO KEYLOCK (SEC)
LANGUAGE
VIDEO FORMAT
VERSION
QUICK SEARCH
EVENT SEARCH
HDD INFO
EVENT LOG
USB BACKUP
BACKUP
DISK BACKUP (Selected Models Only)
5.2 Menu Operation Instruction
ITEM
FUNCTION
QUICK START MENU:
View & change the settings of the quick start menu items.
MENU
Enter / exit the quick start menu
▲▼
Make the selection / Change the setting
◄►
Go to the upper layer or sub-layer / Make the selection
ENTER
Confirm the password entering
ADVANCED MENU:
In the quick start menu, move to “ ”, and press “▼” to enter the advanced
setting menu.
ENTER
Go to the sub-layer of the advanced menu
MENU
Under the sub-layer of the advanced setting menu, use this button to confirm the
settings and go back to the upper layer.
t NEXT
Move to this item and press ENTER to go the next page.
s BACK
Move to this item and press ENTER to go the previous page.
Other operations in the advanced menu are the same as in the quick start menu.
-17-
QUICK START MENU
6. QUICK START MENU
Press MENU” and enter the password to go to the quick-start menu list. The default admin password is 0000.
Users can change the password later. Please refer to “7.2 System Info” at page 31.
6.1 Status
In this menu list, you can check and change some display settings.
Move to
, and you will see the following screen:
QUICK START
ADVANCE
CHANNEL TITLE
EVENT STATUS
DATE DISPLAY
ON
ON
ON
IMAGE SIZE
QUALITY
IMAGE PER SECOND
CIF
BEST
100
RECORD TIMER
DETECTION TIMER
OFF
OFF
DATE
FORMAT
DAYLIGHT SAVING
2008 / APR / 24
Y/M/D
OFF
uv SELECT
s BACK
t NEXT
10 : 20 : 24
ENTER
The submenu items are described below:
1)
CHANNEL TITLE
Select to display the channel title or not (ON / OFF).
2)
EVENT STATUS
Select to display the symbols of the event or not (ON / OFF).
3)
DATE DISPLAY
Select to display the date, status icons & remaining HDD capacity or not (ON / OFF).
-18-
QUICK START MENU
6.2 Manual Record
In this menu list, you can set record settings.
Move to
, and you will see the following screen:
QUICK START
ADVANCE
CHANNEL TITLE
EVENT STATUS
DATE DISPLAY
ON
ON
ON
IMAGE SIZE
QUALITY
IMAGE PER SECOND
CIF
BEST
100
RECORD TIMER
DETECTION TIMER
OFF
OFF
DATE
FORMAT
DAYLIGHT SAVING
2008 / APR / 24
Y/M/D
OFF
uv SELECT
s BACK
t NEXT
10 : 29 : 00
ENTER
The submenu items are described below:
1)
IMAGE SIZE
Select one of the image sizes: FRAME, FIELD or CIF.
2)
QUALITY
Select one of the 4 quality options: SUPER BEST, BEST, HIGH and NORMAL.
3)
IMAGE PER SECOND
Select the images per second for MANUAL RECORD.
Note: For different model’s actual recording IPS, please see “1.3 Specifications” at page 2.
-19-
QUICK START MENU
6.3 Timer
In this menu list, you can schedule different sets of time for recording and detection function.
Move to
, and you will see the following screen:
QUICK START
ADVANCE
CHANNEL TITLE
EVENT STATUS
DATE DISPLAY
ON
ON
ON
IMAGE SIZE
QUALITY
IMAGE PER SECOND
CIF
BEST
100
RECORD TIMER
DETECTION TIMER
OFF
OFF
DATE
FORMAT
DAYLIGHT SAVING
2008 / APR / 24
Y/M/D
OFF
uv SELECT
s BACK
t NEXT
10 : 29 : 00
ENTER
The submenu items are described below:
1)
RECORD TIMER
Use ▲ / ▼ to change the setting (ON / OFF). When it’s set to “ON”, press “ENTER” to go to its submenu for further
settings.
RECORD TIMER
0
2
4
6
8
10
12
14
16
18
20
22
24
SUN
MON
TUE
WED
THU
FRI
SAT
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTINGS
uv s t MOVE SELECT
X axis
Y axis
Operation
0 ~ 24 hours. Each time interval within a square is two hours (divided into four 30-minutes).
Monday ~ Sunday.
Move to the start time point, and press “ENTER” to set the start time point (marked in red
color). Then, press ▲ / ▼ / ◄ / ► to set the timer-recording schedule. After setup, press
“ENTER” again to create an ending time point (marked in yellow color) and press “MENU” to
exit.
-20-
QUICK START MENU
2)
DETECTION TIMER
Use ▲ / ▼ to change the setting (ON / OFF). When it’s set to “ON”, press “ENTER” to go to its submenu for further
settings.
DETECTION TIMER
0
2
4
6
8
10
12
14
16
18
20
22
24
SUN
MON
TUE
WED
THU
FRI
SAT
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTINGS
uv s t MOVE SELECT
X axis
Y axis
Operation
0 ~ 24 hours. Each time interval within a square is two hours (divided into four 30-minutes).
Monday ~ Sunday.
Move to the start time point, and press “ENTER” to set the start time point (marked in red
color). Then, press ▲ / ▼ / ◄ / ► to set the timer-recording schedule. After setup, press
“ENTER” again to create an ending time point (marked in yellow color) and press “MENU” to
exit.
Note: This function here is only for event record timer setup and activation. For motion detection function
setup and activation, please refer to section “7.1.2 Detection” at page 24.
6.4 Date
In this menu list, you can set up the system date and time for this device.
Note: Please DO NOT change the date or time of your DVR after the recording function is activated.
Otherwise, the recorded data will be disordered and you will not be able to find the recorded file
to backup by time search. If users change the date or time accidentally when the recording
function is activated, it’s recommended to clear all HDD data, and start recording again.
Note: The DVR time might get reset when the DVR battery is low or even running out of power. If so,
please replace the DVR battery, CR2032, right away as instructed in “APPENDIX 6 DVR BATTERY
REPLACEMENT” at page 58.
-21-
QUICK START MENU
Press “MENU” to enter the main menu list. Move to
, and you will see the following screen:
QUICK START
ADVANCE
CHANNEL TITLE
EVENT STATUS
DATE DISPLAY
ON
ON
ON
IMAGE SIZE
QUALITY
IMAGE PER SECOND
CIF
BEST
100
RECORD TIMER
DETECTION TIMER
OFF
OFF
DATE
FORMAT
DAYLIGHT SAVING
2008 / APR / 23
Y/M/D
OFF
uv SELECT
s BACK
t NEXT
11 : 20 : 45
ENTER
The submenu items are described below:
1)
DATE
Set the current date and time. The default order is “YEAR – MONTH – DATE HOUR : MIN : SEC”.
2)
FORMAT
Select one date format from the following 3 options: Y-M-D, M-D-Y, D-M-Y.
3)
DAYLIGHT SAVING
Use the ▲ / ▼ to specify whether to use daylight-saving time (ON / OFF). When it’s set to “ON”, press “ENTER”
to go to its submenu for further settings.
DAYLIGHT SAVING
START TIME
END TIME
ADJUST
4TH - SUN - MAR
4TH - SUN - OCT
24 : 00 : 00
24 : 00 : 00
01 : 00
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
Set the start time and end time, and adjust the daylight saving time in hour. The above example means during the
daylight-saving time period (starting from the 4th Sunday of March and ending on the 4th Sunday of October), the
system time will plus one hour. After setup, press “ENTER” again to create an ending time point and press “MENU” to
exit.
-22-
ADVANCED MENU
7. ADVANCED MENU
Note: The following menu display takes 16CH DVR as an example, and some display may differ from the
actual display when users are using a 8CH or 4CH DVR.
Press “MENU” and enter the password to go to the quick-start menu list. Then, move to “ADVANCE” to enter the
advanced setting menu. The default admin password is 0000. Users can change the password later. Please refer to
“7.2 System Info” at page 31.
It is recommended that consult your installer to setup this advanced menu.
7.1 Advanced Configuration
In this menu list, you can check or change CAMERA / DETECTION / ALERT / NETWORK / SNTP / DISPLAY /
RECORD / REMOTE settings.
Move to “
”, and you will see the following screen:
ADVANCE CONFIG
CAMERA
DETECTION
ALERT
NETWORK
SNTP
DISPLAY
RECORD
REMOTE
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
7.1.1 Camera
In this submenu, you can make advanced camera settings, such as changing the camera title, or adjust the
brightness. Move to “CAMERA”, and press “ENTER”. You will see the following screen:
CAMERA
TITLE
BRIG
CONT
SATU
HUE
COV.
REC
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
NEXT
128
128
128
128
128
128
128
128
128
128
098
098
098
098
098
098
098
098
098
098
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
The submenu items are described below. While you changing the camera setting, you can preview the changing
on the screen.
~23~
ADVANCED MENU
1)
TITLE
You can change the default camera naming here. The default title is the channel number.
Move to the camera title you want to change, and press “ENTER” on the control panel of the DVR to access the
character selection screen. Assign a new name to the camera up to six characters (letters or symbols or
numbers).
2)
BRIG / CONT / SATU / HUE
You can adjust the brightness/contrast/saturation/hue of each channel here. The default value of CONT is 098,
and others are 128. The value is adjustable from 0 to 255.
3)
COV
Select if you want to mask the selected channel under recording (ON / OFF). When this function is activated, the
wording “COV.” will be shown on the channel screen.
4)
REC
Select if you want to enable recording for the selected channel (ON / OFF). When this function is activated, the
symbol “
” will be shown on the channel screen.
7.1.2 Detection
In this submenu, you can set up detection-related functions.
Move to “DETECTION”, and press “ENTER”. The submenu items are described below:
1)
TITLE
Show the camera title of each channel set in “CAMERA”.
2)
DET
The available options vary depending on the model you have.
For Model 5 & 7: Select if you want to activate the motion detection function for the selected channel (ON/OFF).
For Model 1, 2, 3, 4, 6 & 8: Select HIGH / NORMAL / LOW to activate the motion detection function with different
sensitivity for the selected channel, or select OFF to disable this function.
3)
AREA
Press “ENTER” to set the detection area. You will see similar screens as the following:
Pink blocks represent the area that is not being detected while the transparent blocks are the area under
detection.
There are two different methods to set the detection area depending on the model you have.
Model 1, 2, 3, 4, 6 & 8
Transparent blocks are the area under
detection.
Press / to choose the height of the
area.
Press “ENTER” to confirm the start area.
Press / to choose the width of the
detection area.
You can also set up multi-detection area. When any movement is detected, you will
see the grids are flashing.
*Pink blocks represent the area that is not being detected while the transparent blocks are the area under detection.
~24~
ADVANCED MENU
Model 5 & 7
*Pink blocks represent the area that is not being detected while the transparent blocks are the area under detection.
There are three detection areas for your choice:
Press “” or ” ” once to broaden the detection area.
Press “” or ” ” once to narrow the detection area.
4)
LS (Level of Sensitivity) (Selected models only)
“LS” is to set the sensitivity of comparing two different images. The smaller the value is, the higher sensitivity for
motion detection.
5)
SS (Spatial Sensitivity) (Selected models only)
“SS” is to set the sensitivity for detecting the size of one object (the number of the grids) on the screen. The
smaller the value is, the higher sensitivity for motion detection.
Note: The default setting of SS is 03, which means once an object is detected more than 3 grids, the
system will get triggered. So the value of SS must be less than the number of grids that you set
up for the motion detection area.
6)
TS (Time of Sensitivity) (Selected models only)
“TS” is to set the sensitivity regarding how long one object stays in the detection area and triggers the recording.
Depending on the model you have, you may see either of the following methods:
a). Select a value -- The smaller the value is, the higher sensitivity for motion detection.
b). Select an option – HIGH / NORMAL.
7)
RE (Reference) (Selected models only)
“RE” is to set a reference for detection. The default value is 10, which means the DVR will compare 10 continuous
images at one time according to the sensitivity of LS, SS, TS simultaneously.
8)
ALARM (Selected models only)
Select N.C. (Normally Closed) / N.O. (Normally open) / OFF for the alarm polarity. The default alarm value is OFF.
7.1.3 Alert
In this menu list, you can set alerts for different kinds of situations, such as when HDD is full.
Move to “ALERT”, and press “ENTER”. You will see the following screen:
ALERT
EXT. ALERT
INT. BUZZER
KEY BUZZER
VLOSS BUZZER
MOTION BUZZER
ALARM BUZZER
HDD BUZZER
ALARM DURATION (SEC)
HDD NEARLY FULL (GB)
ON
ON
ON
ON
ON
ON
ON
05
05
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
~25~
ADVANCED MENU
The submenu items are described below:
1)
EXT. ALERT
Select to enable or disable the sound when any external alarm is triggered (ON / OFF).
2)
INT. BUZZER
Select to enable or disable the sound (ON / OFF) for all the internal buzzers: KEY BUZZER, VLOSS BUZZER,
MOTION BUZZER, and ALARM BUZZER.
Note: When this item is set to OFF, item 3) to item 6) will be disabled even though they are set to ON.
3)
KEY BUZZER
Select to enable or disable the sound when pressing the buttons on the front panel (ON / OFF).
4)
VLOSS BUZZER
Select to enable or disable the sound when video loss happened (ON / OFF).
5)
MOTION BUZZER
Select to enable or disable the sound when any motion alarm is triggered (ON / OFF).
6)
ALARM BUZZER
Select to enable or disable the sound when any internal alarm is triggered (ON / OFF).
7)
HDD BUZZER
Select to enable or disable the sound (ON / OFF) when the HDD remaining capacity reaches to the value set in
“HDD NEARLY FULL (GB)”.
8)
ALARM DURATION (SEC)
Press ▲ / ▼ to set the duration time of alarm recording in second (5 / 10 / 20 / 40).
9)
HDD NEARLY FULL (GB)
If HDD BUZZER is enabled, press ▲ / ▼ to have a buzzer notification when the HDD available capacity is
5/10/15/20 GB left.
7.1.4 Network
In this menu list, you can set up the network.
Move to “NETWORK”, and press “ENTER” to enter the submenu. You will see the following screen:
NETWORK
NETWORK TYPE
IP
GATEWAY
NETMASK
PRIMARY DNS
SECONDARY DNS
PORT
STATIC
192 . 168 . 001 . 080
192 . 168 . 001 . 080
255 . 255 . 255 . 000
168 . 095 . 001 . 001
139 . 175 . 055 . 244
0080
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
The submenu items are described below:
‧ STATIC
1)
NETWORK TYPE
Select the network type as STATIC and set all the information needed in the DVR.
2)
NETWORK INFORMATION (IP / GATEWAY / NETMASK)
Key in all the network information obtained from your ISP (Internet Service Provider).
~26~
ADVANCED MENU
3)
DNS (PRIMARY DNS / SECONDARY DNS)
Key in the IP address of the domain name server obtained from your ISP (Internet Service Provider).
4)
PORT
The valid number ranges from 1 to 9999. The default value is 80. Typically, the TCP port used by HTTP is 80.
However in some cases, it is better to change this port number for added flexibility or security.
See the example below:
STATIC
NETWORK TYPE
STATIC
IP
192 . 168 . 001 . 080
GATEWAY
192 . 168 . 001 . 080
NETMASK
255 . 255 . 255 . 000
PRIMARY DNS
168 . 095 . 001 . 001
SECONDARY DNS
139 . 175 . 055 . 244
PORT
0080
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
‧ PPPOE
1)
NETWORK TYPE
Select the network type as PPPOE.
2)
USER NAME / PASSWORD
Set “username” and “password” subscribed from your ISP supplier
3)
DNS (PRIMARY DNS / SECONDARY DNS)
Key in the IP address of the domain name server obtained from your ISP (Internet Service Provider).
4)
PORT
The valid number ranges from 1 to 9999. The default value is 80. Typically, the TCP port used by HTTP is 80.
However in some cases, it is better to change this port number for added flexibility or security.
See the example below:
PPPOE
NETWORK TYPE
USER NAME
PASSWORD
IP
GATEWAY
NETMASK
PRIMARY DNS
SECONDARY DNS
PORT
PPPOE
ac123456
tech123456
000 . 000 . 000 . 000
000 . 000 . 000 . 000
000 . 000 . 000 . 000
168 . 095 . 001 . 001
139 . 175 . 055 . 244
0080
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
Note: The PPPOE function needs to have one “username” and one “password” subscribed from one ISP supplier
and a “DDNS account” to transforming the dynamic IP corresponding to a specific “Hostname”.
‧ DHCP
1)
NETWORK TYPE
Select the network type as DHCP.
~27~
ADVANCED MENU
2)
DNS (PRIMARY DNS / SECONDARY DNS)
Key in the IP address of the domain name server obtained from your ISP (Internet Service Provider).
3)
PORT
The valid number ranges from 1 to 9999. The default value is 80. Typically, the TCP port used by HTTP is 80.
However in some cases, it is better to change this port number for added flexibility or security.
See the example below:
DHCP
NETWORK TYPE
IP
GATEWAY
NETMASK
PRIMARY DNS
SECONDARY DNS
PORT
DHCP
000 . 000 . 000 . 000
000 . 000 . 000 . 000
000 . 000 . 000 . 000
168 . 095 . 001 . 001
139 . 175 . 055 . 244
0080
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
Note: This DHCP function needs to be supported by a router or a cable modem network with DHCP
services and a “DDNS account” to transforming the dynamic IP corresponding to a specific
“Hostname”.
7.1.5 SNTP
In this menu list, you can set to synchronize your DVR time with the networked computer systems.
Note: Before using this function, please connect your DVR to Internet.
Move to “SNTP”, and press “ENTER” to enter the submenu. You will see the following screen:
SNTP
GMT
(GMT+08:00) TAIPEI
NTP SERVER
tock.stdtime.gov.tw
SYNC PERIOD
DAILY
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
1)
GMT
Select your time zone. There are 75 time zones for you to choose.
2)
NTP SERVER
Users can change the default NTP server to another server they’re familiar with.
3)
SYNC PERIOD
Select to synchronize the DVR time everyday (DAILY), or turn this function off (OFF).
~28~
ADVANCED MENU
7.1.6 Display
In this menu list, you can set up the settings of display.
Move to “DISPLAY”, and press “ENTER” to enter the submenu. You will the following screen:
DISPLAY
DE-INTERLACE
ON
QUAD DWELL DURATION (SEC) (Selected Models Only)
03
FULL SCREEN DWELL DURATION (SEC)
03
VGA OUTPUT (Selected Models Only)
1024 x 768
DISPLAY COVERT
ON
HDD DISPLAY MODE
SIZE
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
The submenu items are described below:
1)
DE-INTERLACE
Select to enable or disable the de-interlace function (ON / OFF).
Note: If you set the recording image size as “FRAME”, please TURN ON de-interlace function.
If you set the recording image size as “CIF”, please TURN OFF the de-interlace function.
2)
QUAD DWELL DURATION (SEC) (Selected Models Only)
Set the quad dwell duration time (3 / 5 / 10 / 15 seconds).
3)
FULL SCREEN DWELL DURATION (SEC)
Set the full screen dwell duration time (3 / 5 / 10 / 15 seconds).
4)
VGA OUTPUT (Selected Models Only)
Select the VGA output resolution. There are seven options for your choice:
800 x 600 / 1024 x 768 (default) / 1280 x 1024 / 1440 x 900 / 1400 x 1050 / 1680 x 1050 / 1600 x 1200
Note: To have the best image quality on your LCD monitor, make sure (1) the selected DVR VGA output
resolution is supported by your monitor, and (2) the VGA output settings on both the LCD monitor
and DVR are consistent.
If the image is not positioned or scaled properly, please go to your monitor’s menu for adjustment.
For details, please refer to the user manual of your LCD monitor.
5)
DISPLAY COVERT
Select “ON” or “OFF” to display or hide the wording “COV.” when covert recording is activated in “CAMERA”.
6)
HDD DISPLAY MODE
Select “SIZE” to show the remaining HDD capacity for recording in GB, or “TIME” to show the remaining recording
time.
7.1.7 Record
In this menu list, you can set up the settings of display.
Note: Please DO NOT change the date or time of your DVR after the recording function is activated.
Otherwise, the recorded data will be disordered and you will not be able to find the recorded file
to backup by time search. If users change the date or time accidentally when the recording
function is activated, it’s recommended to clear all HDD data, and start recording again.
~29~
ADVANCED MENU
Move to “DISPLAY”, and press “ENTER” to enter the submenu. You will the following screen:
RECORD
MANUAL RECORD ENABLE
EVENT RECORD ENABLE
TIMER RECORD ENABLE
EVENT RECORD IPS
TIMER RECORD IPS
OVERWRITE
EVENT RECORD ALL CHANNELS
KEEP DATA LIMIT (DAYS)
ON
ON
ON
100
100
ON
ON
07
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
The submenu items are described below:
1)
MANUAL RECORD ENABLE
Set the manual recording function on / off.
2)
EVENT RECORD ENABLE
Set the event recording function on / off.
3)
TIMER RECORD ENABLE
Set the timer recording function on / off.
4)
EVENT RECORD IPS
Select the images per second for EVENT RECORD (Recording that is triggered by alarm or motion).
Note: For different model’s actual recording IPS, please see “1.3 Specifications” at page 2.
5)
TIMER RECORD IPS
Select the images per second for TIMER RECORD (Recording that is activated according to the scheduled time).
Note: For different model’s actual recording IPS, please see “1.3 Specifications” at page 2.
6)
OVERWRITE
Select “ON” to overwrite previous recorded data in your HDD when the HDD is full. When this function is on and
the HDD is full, the DVR will clear 8GB data from the oldest for continuous recording without notice.
7)
EVENT RECORD ALL CHANNELS
Select to record all channels (ON) or record the channel with an event only (OFF) for any event.
8)
KEEP DATA LIMITS (DAYS)
Assign the maximum days to keep recorded data from 01 to 31, and the data older than the specified days will be
removed, or select “OFF” to disable this function.
7.1.8 Remote
In this menu list, you can set up remote devices to work properly.
Move to “REMOTE”, and press ”ENTER”. You will see the following screen:
TITLE
DEVICE
ID
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
NEXT
PTZ
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
000
000
000
000
000
000
000
000
000
000
REMOTE
PROTOCOL
RATE
NORMAL
NORMAL
NORMAL
NORMAL
NORMAL
NORMAL
NORMAL
NORMAL
NORMAL
NORMAL
2400
2400
2400
2400
2400
2400
2400
2400
2400
2400
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
~30~
ADVANCED MENU
The submenu items are described below:
1)
TITLE
Show the camera title of each channel set in “CAMERA”.
2)
DEVICE
Select the device type (CAMERA / PTZ) according to the connected camera for each channel.
3)
ID
Set the ID number (0 ~ 255) for a PTZ camera.
After connecting to a PTZ camera correctly, the default ID of the PTZ camera will be shown on the screen.
4)
PROTOCOL
Select NORMAL (our protocol), P-D (PELCO-D) or P-P (PELCO-P) protocol.
5)
RATE
Set the baud rate of each channel (2400 / 4800 / 9600 / 19200 / 57600 / 115200).
For the connected cameras, such as PTZ and speed dome cameras, etc., please make sure their baud rate
setting is the same as the setting here.
7.2 System Info
In this menu list, you can check or change some system settings.
Move to “
”, and you will see a similar screen as the following:
SYSTEM INFO
SERIAL TYPE
BAUD RATE
HOST ID
PASSWORD
RESET DEFAULT
CLEAR HDD
UPGRADE
R.E.T.R. (MIN) (Selected Models Only)
AUTO KEYLOCK (SEC)
LANGUAGE
VIDEO FORMAT
VERSION
RS485
2400
0
XXXX
RESET
HDD-EXT-252
START
05
NEVER
ENGLISH
PAL
1083-1028-1009-1013-02-0000
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
The submenu items are described below:
1)
SERIAL TYPE
Here shows the serial type of the DVR (RS-485).
2)
BAUD RATE
Set the baud rate of the DVR (2400 / 9600 / 19200 / 38400 / 57600 / 115200).
3)
HOST ID
Set the ID of the DVR (0 ~ 254).
4)
PASSWORD
Reset the password for accessing the DVR system. You can set the password up to 4 digits.
5)
RESET DEFAULT
Press “ENTER” to reset all settings as default, and select “YES” to confirm or “NO” to cancel.
6)
CLEAR HDD
Select the HDD. Press “ENTER” and select “YES” to confirm to clear HDD or “NO” to cancel.
~31~
ADVANCED MENU
7)
UPGRADE (For upgrading firmware / OSD)
Before using the USB flash drive, please use your PC to format the USB flash drive to FAT32 format first.
Save the upgrade file in a compatible USB flash drive, and insert it into the USB port at the front panel.
Then, press “ENTER” and select “YES” to confirm upgrade or “NO” to cancel.
Note: For the list of compatible USB flash drives, please refer to “APPENDIX 2 COMPATIBLE USB FLASH
DRIVE BRAND” at page 54.
8)
R.E.T.R. (MIN) (Selected Models Only)
Select the timeout after which the R.E.T.R. function will be activated (03 / 05 / 10 / 30).
‧ R.E.T.R. On
Press the R.E.T.R. key on the IR remote controller to enable the timeout function. Key in the password, and the
R.E.T.R. delay icon “
” (in green background) will be shown on the screen. When the RETR function is
activated, the R.E.T.R. on icon “
” (in red background) will be shown on the screen.
‧ R.E.T.R. Off
Press any key (except “POWER”) and enter the password to turn off the RETR function.
9)
AUTO KEYLOCK
Set the time-out in second after which the key lock function is activated (Never / 10 / 30 / 60).
10) LANGUAGE (Multilingual OSD)
Select the language of the OSD.
11) VIDEO FORMAT
Here shows the information of the DVR video format (NTSC / PAL).
12) VERSION
Here shows the firmware version information
7.3 Event Info
In this menu list, you can quickly search the recorded file by time or event, and check all the HDD and event
information (event type, time and channel).
Move to “
”, and press “ENTER”. You will the following screen:
EVENT INFO
QUICK SEARCH
EVENT SEARCH
HDD INFO
EVENT LOG
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
~32~
ADVANCED MENU
7.3.1 Quick Search
In this menu list, you can search any specific events by time and directly play the file you find.
Move to “QUICK SEARCH”, and press “ENTER”. You will see a similar screen as the following:
DATE
SEARCH HDD
START
TIME SEARCH
2008 / APR / 24
22 : 48 : 00
ALL HDD
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
The submenu items are described below:
1)
DATE
Select the specific time period (YEAR / MONTH / DAY / HOUR / MIN) that you want to search.
2)
SEARCH HDD
Change to the HDD you want to search if there are more than one HDD in your DVR by pressing ▲ / ▼.
3)
START
Move to “START” and press “ENTER” to search and directly playback the recorded files.
7.3.2 Event Search
Move to “EVENT SEARCH”, and press “ENTER”. You will see the following screen:
DATE
CHANNEL
EVENT
SEARCH HDD
START
EVENT SEARCH
2008 / JUN / 17
22 : 48 : 00
01
MOTION
ALL HDD
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
The submenu items are described below:
1)
DATE
Set the date and time you want to search for events.
2)
CHANNEL
Press ▲ / ▼ to select the channel.
3)
EVENT
Select the event type: MOTION or ALARM.
4)
SEARCH
Change to the HDD you want to search if there are more than one HDD in your DVR by pressing ▲ / ▼.
5)
START
Move to “START” and press “ENTER” to search and directly playback the recorded files.
~33~
ADVANCED MENU
7.3.3 HDD Info
In this menu list, you can view the remaining capacity of all the connected HDDs in this device.
Move to “HDD INFO”, and press “ENTER”. You will see a similar screen as the following:
HDD NUM
HDD INFO
HDD SIZE (GB)
HDD NUM
HDD SIZE (GB)
HDD–MASTER–1
HDD–MASTER–2
233
NO HDD
NO HDD
NO DISK
HDD–SLAVE–1
DISK-RW
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
7.3.4 Event Log
In this menu list, you can view all the event information (event type, time and channel) or clear all log records.
Move to “EVENT LOG”, and press “ENTER”. You will see a similar screen as the following:
EVENT
EVENT LOG
TIME
NET LOGIN
NET LOGIN
NET LOGIN
KEY UNLOCK
VLOSS
VLOSS
VLOSS
VLOSS
POWER ON
KEY UNLOCK
2008 / APR / 24
2008 / APR / 24
2008 / APR / 24
2008 / APR / 24
2008 / APR / 24
2008 / APR / 24
2008 / APR / 24
2008 / APR / 24
2008 / APR / 24
2008 / APR / 23
PREV
NEXT
COMMENT
10:36:50
10:33:12
10:28:15
10:27:14
10:23:34
10:23:34
10:23:34
10:23:34
10:23:30
14:37:30
04
03
02
01
CLEAN
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
7.4 Backup
In this menu list, you can choose to make a copy for a specified period time to a compatible USB flash drive for
your own purpose.
Move to
, and press “ENTER”. You will the following screen:
~34~
ADVANCED MENU
BACKUP
USB BACKUP
DISK BACKUP (Selected Models Only)
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
7.4.1 USB BACKUP
Before making USB backup, please check if:
a)
The USB flash drive is supported by your DVR. If not, the message “USB ERROR” will be shown on the
screen.
For the list of the compatible USB flash drives, please refer to “APPENDIX 2 COMPATIBLE USB FLASH
DRIVE BRAND” at page 54.
b)
The format of your USB flash drive must be "FAT 32". If not, please format it to “FAT 32” in your PC.
c)
There is no data in the USB flash drive. If yes, it’s recommended to clear all data in the USB flash drive
before starting the backup.
Note: When USB backup starts, it’s not allowed for OSD menu operation or network backup in order to
keep the consistency of the video data.
Note: You can backup up to 2GB video data for one-time USB backup. To backup more data, please set
the time & channel(s) you want, and start USB backup again.
Move to “USB BACKUP”, and press “ENTER”. You will see a similar screen as the following:
START TIME
END TIME
AVAILABLE SIZE
CHANNEL
USB BACKUP
2008 / APR / 24
2008 / APR / 24
01
05
09
13
□
□
□
□
02
06
10
14
□
□
□
□
03
07
11
15
HDD NUM
START
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING
uv SELECT s BACK t NEXT ENTER
The submenu items are described as below:
1)
START TIME
Select the start time of the backup.
~35~
13:00:05
13:10:05
1960.0MB
□ 04
□ 08
□ 12
□ 16
ALL HDD
ADVANCED MENU
2)
END TIME
Select the end time of the backup.
3)
AVAILABLE SIZE
Display the available capacity in the inserted USB flash drive.
4)
CHANNEL
Select channels by pressing “ENTER” to change the symbol in front of the channel number.
Symbol “
” means that this channel is selected to backup.
Symbol “ □ ” means that this channel is not selected to backup.
5)
HDD NUM
Press “ENTER” to select the HDD containing the data you need.
6)
START
Press “ENTER” to start copying the chosen data to the USB flash drive.
7.4.2 DISK BACKUP (Selected Models Only)
Before making disk backup, please check if the type of your CD or DVD is CD-R or DVD-R. The maximum number
of backup files in the CD or DVD is 41.
Note: During the backup process, a file player will also be copied into your disk, and you will see a
message “BACKUP PLAYER” shown on the screen.
Move to “DISK BACKUP”, and press “ENTER”. You will see a similar screen as the following:
START TIME
END TIME
AVAILABLE SIZE
CHANNEL
DISK BACKUP
2008 / APR / 24
2008 / APR / 24
01
05
09
13
□
□
□
□
02
06
10
14
□
□
□
□
03
07
11
15
HDD NUM
START
19:00:05
21:00:05
3.79 GB
□ 04
□ 08
□ 12
□ 16
ALL HDD
PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTINGS
uv SELECT s BACK t NEXT ENTER
The submenu items and their functions are almost the same as USB BACKUP. For the description of the submenu
items, please refer to the previous page.
The process below describes how to make a disk backup:
a) Press “EJECT” to open the disk tray. Put a CD or DVD into the DVD writer, and press “EJECT” again to close
the disk tray.
Note: Check if the type of your CD or DVD is CD-R or DVD-R. The maximum number of backup files in
the CD or DVD is 41.
b) Press “MENU”, and go to “ADVANCE” J “BACKUP”. Select “DISK BACKUP”, and you will see the submenu
items almost the same as USB BACKUP.
For the description of the submenu items, please refer to “5.8.1. USB BACKUP”.
c) Set the start time, end time, channels and HDD.
d) Move to “START”, and press “ENTER” to start backup.
~36~
ADVANCED MENU
While disk backup is processing, users will see the backup completed percentage on the screen.
Note: During the backup process, a file player will also be copied into your disk, and you will see a
message “BACKUP PLAYER” shown on the screen.
e) After disk backup is completed, “BACKUP SUCCESS” will be prompted on the screen. Press “EJECT” to eject
the disk tray and get your disk.
f) Put the CD or DVD into the DVD-ROM drive of your PC. Install the file player “PLAYER.EXE”, and double click
any backup file to play it directly in your PC and see if the backup is successful.
Note: The supported PC operation systems are Windows Vista, XP & 2000.
~37~
REMOTE OPERATION
8. REMOTE OPERATION
You can also control the DVR remotely via the supplied licensed software “Video Viewer”, Internet Explorer web
browser, and Apple’s QuickTime player.
8.1 Supplied Licensed Software
The sections below describe frequently-used functions of the Video Viewer. For details about this software and
network settings, please download its extended user manual from the following link:
http://www.surveillance-download.com/user/CMS.pdf
8.1.1 Installation & Network Connection
1)
Install the software
Step1: Place the supplied CD into your CD-ROM or DVD-ROM drive. The program will be automatically run.
Step2: Click “Licensed Software AP” to install Video Viewer, or click “Download Latest Version” under
“Licensed Software AP” to download the latest version of Video Viewer from the Internet.
Step3: Follow the on-screen instructions to finish the installation. When the installation is completed, a
shortcut icon “
2)
” will be placed on your PC desktop.
Network Connection
Local Connection (via LAN)
LAN is used when it’s the first time to remotely access the DVR and you need to configure the network
setting of your DVR based on your network type in advance.
1)
Connect the DVR to your PC via a RJ45 network cable. The default DVR values are as follows:
Item
Default Value
IP address
192.168.1.10
User name
admin
Password
admin
Port
80
2)
Set the PC’s IP address as “192.168.1.XXX” (1~255, except 10) in order to make the PC and DVR under the
same domain.
3)
Double-click “
” icon on your PC desktop to enter the control panel. By defaults, the “Address Book” panel
will be displayed on the right side of the control panel.
4)
Click “ ”
“
” to key in the default IP address, user name, password, and port number of the DVR
you intend to connect.
~38~
REMOTE OPERATION
OR
Click “
”
“
” to search the available IP address(es) of other DVR(s) under the same domain as
your PC’s IP address. The found address(es) will be listed, and can be added into the address book by
clicking “
5)
”.
Double-click the IP address you just added into the address book to log in.
Remote Connection (via Internet)
When the network configuration of your DVR is completed, you can access your DVR remotely via Internet.
1)
Double-click “
” icon on your PC desktop to enter the control panel. By defaults, the “Address Book” panel
will be displayed on the right side of the control panel.
2)
”
”
Click ”
intend to connect.
” to key in the IP address, user name, password, and port number of the DVR you
OR
Click ”
”
”
” to search the available IP address(es) of other DVR(s) under the same domain
as your PC’s IP address. The found address(es) will be listed, and can be added into the address book by
clicking ”
”.
3) Double-click the IP address you just added into the address book to log in.
8.1.2 Control Panel Overview
Two control panels are available and can be switched depending on your use habit.
Simplified Version (Default)
~39~
REMOTE OPERATION
Full Function Version
Main Button Overview
Button
Simplified
Full Function
Function
Address Book
Description
Click to show the predefined IP address(es). You can add, remove or
search the IP address to log in the DVR remotely.
Miscellaneous Control
Log
/
/
Record / Record Stop
Snapshot
Information
DVR Control
Remote
Config
Click to go into the detailed DVR setting.
Record
Setting
Click to go to the detailed record setting.
Custom
Setting
Click to choose the language of this program. The
language change will take effect when this
program is closed and executed again.
Click to view all event and recording logs, search the desired log(s) by
date, or playback the recording of the selected log.
Click to start / stop the manual recording.
Click to take a snapshot of the current view. The snapshot will be saved
in the path you specified in “Record Setting”.
Click to show the current network connection details.
Click to go to the DVR control panel to operate the DVR remotely.
~40~
REMOTE OPERATION
8.1.3. General Operation
Record
To record remotely at the same time for any event or alarm at the DVR side, click “
” or “
” → “
” to go to
the “Record Setting” page.
In the “Record Setting” page, you can set the following items:
‧Record type
‧Hard disk overwriting
‧Pre- / post-alarm record time
‧Record time setting
‧Record path
If “Manual” is checked, click “
” or “
” on the main control panel to start the manual recording immediately,
and the recordings will be saved in the specified location. The red text indication “REC” will be shown at the top
left corner of the image display view.
If “Motion” and / or “Alarm” are checked, the recording function will also be enabled at the remote side when any
event is triggered at the DVR side, and the recordings will be saved in the specified location.
Playback
To play a recording, click “
” or “
”, and select the “Record” tab or “Backup” tab. A list of all the recordings
will be shown by defaults, and you can also sort out the logs you want to speed up the search time.
~41~
REMOTE OPERATION
To immediately play a recording, select a log from the list, and click “Play”, or double-click the selected log.
Network Backup
Click “
” → “
”, or click “
” to go into the “Backup” page as follows, and you can select a specific time
range or event to make a video backup remotely.
The file(s) you backup will be from the currently selected IP address.
Function
Description
HDD Number / Channel
Specify the hard disk (HDD Number) and channel number (Channel)
within which have the video data you need.
Download by Time
Specify the time range within which has the video data you want in
the “Start Time” and “End Time” columns.
Download by Event
Select an event log from the event list. This list shows all logs in the
specified DVR from the latest to the earliest.
‧To quickly find the events you need, check or uncheck the event
type “System” / “Manual” / “Alarm” / “Motion”, and select the log you
want.
‧To view the earlier or later logs that are not shown in the current
page, click “Prev. Page” or “Next Page”.
‧To refresh the event list, click “Reload”.
File Path
Assign the location where the backup files are saved.
Simultaneous Playback
To view the backup images simultaneously when the download
process is in progress, select the checkbox “Simultaneous Playback”.
You will see the backup images while the images are being
downloaded to the PC or notebook.
~42~
REMOTE OPERATION
Function
Description
To simply backup images without previewing, deselect the checkbox
“Simultaneous Playback”. You will only see a message box indicating
the total time needed, the current status and the saving location.
Download / Cancel
Click “Download” to start or “Cancel” to discard the video backup.
8.1.4. E-Map
Video Viewer is also a Central Management System (CMS) software, which allows network device control &
management for up to 16 devices simultaneously.
Note: Before using this function, make sure Video Viewer is connected to all the devices (up to 16) you
want to monitor.
E-Map is ONLY available when the control panel is switch to the full function version.
How to Add an E-Map Group
STEP1: In the simplified version, click “
” to switch the control panel to the full function version, and click “
”
to enter the E-Map page as follows.
Note: To know where the buttons are, please refer to “Simplified Version (Default) at page 39, and “Full
Function Version” at page 40.
STEP2: Right-click to show the shortcut menu on the top-left panel, and select the E-Map group you want to add.
There are three E-Map groups you can add: Google E-MAP, Single E-MAP, and Building E-MAP.
~43~
REMOTE OPERATION
~44~
REMOTE OPERATION
STEP3: When the E-Map group is created, you will see the tree on the top-left panel, showing all the devices
you’ve added to this group.
Icon
Description
The connected device is camera. When it’s selected, it will become red.
The connected device is DVR. When it’s selected, it will become red.
For any motion or alarm event, it will appear on the screen to catch your attention.
To know what’s happening quickly, double-click the device icon on the E-Map to show the live
view.
How to Edit / Remove an Existing E-Map Group
For Google E-Map Group
Right-click on the group name to show the shortcut menu list, and select
“Edit E-MAP” or “Remove E-MAP” as needed.
You can also add a single E-Map group (Add Single E-MAP) or Building
E-Map group (Add Building E-MAP) into the existing Google E-Map
group.
~45~
REMOTE OPERATION
For Single E-Map Group
Right-click on the group name to show the shortcut menu list, and select
“Edit E-MAP” or “Remove E-MAP” as needed.
For Building E-Map Group
Right-click on the group name to show the shortcut menu list, and select
“Edit Building E-MAP” or “Remove E-MAP” as needed.
~46~
REMOTE OPERATION
To edit or remove a certain level of the building E-Map group, right click
on the level name, and select “Edit E-MAP” or “Remove E-MAP” as
needed.
~47~
REMOTE OPERATION
8.2 IE Web Browser
You can view the images or operate your DVR with IE web browser.
Note: The supported PC operation systems are Windows 2000 and Windows XP and Vista
Step 1: Key in the IP address used by your DVR in the URL address box, such as 60.121.46.236, and press Enter.
You will be prompted to enter the user name and password to access the DVR.
If the port number your DVR used is NOT 80, you need to key in the port number additionally. The format is
ipaddress:portnum. For example, for IP address 60.121.46.236 and port No. 888, please key
in ”http://60.121.46.236:888” into the URL address box, and press “Enter”.
Step 2: Enter the user name and password, the same as the ones used at AP login, and click “OK”. You will see a
similar screen as the following when the login information is correct.
Note: The buttons and functions described below are taking 4CH DVR model as an example.
NO.
Function
Description
1
Home
2
Config.
Click
3
PTZ
Click
4
Channel Selection
5
Selection
6
Display Mode
Click
to go to the main page of the DVR
to go to the detailed DVR setting.
to enter the PTZ mode.
Click one of the number to switch to the channel you want to see in full screen.
Click
or
Click to show 4-cut display.
:
Click to display each channel one by one, starting from CH1. When the last channel is
displayed, it will start from CH1 again.
To exit from this display mode, press any other channel display button.
:
7
Menu and Arrow Keys
Click to enter the menu / exit the menu mode.
:
/
/
8
Event
Click
to go to the previous / next channel, or change setting.
:
:
Move up / down to select the previous / next menu or sub-menu function, or change
the setting.
Move left / right to the previous / next sub-menu items.
to enter the playback search settings screen.
~48~
REMOTE OPERATION
NO.
Function
Description
9
Snapshot
Click
to take a snapshot for the current view, and open another browser window to display
the captured image.
10
Key Lock
Click
to enable the DVR key lock function. To unlock the DVR, key in your password, and
press
.
11
Enter
Click
to confirm the setting or enter your selection.
12
Digital Zoom
Click
to zoom in / out the selected channel image.
13
Search
Click
to enter the DVR full search menu.
You can check all the logs here, and select one of them to payback.
(Stop) /
Playback)
14
Playback control buttons
(Play) /
(Rewind) /
(Forward) /
(Pause) /
(Slow
Rewind / Forward
Click once to get 4X fast rewind / forward, twice to get 8X, three times to get 16X, and four
times to get 32X the highest.
Slow Playback
Click once to get 4X slow playback and twice to get 8X slow playback.
15
Web Transmission
H.264 / M-JPEG / QuickTime (Depending on the model you have)
QuickTime is Apple Inc.’s multimedia software. You need to have QuickTime installed in you
operation system first. When “QuickTime” is selected, you will be promoted to enter the user
name and password to access the server of the DVR.
16
Change Quality
BEST / HIGH / NORMAL / BASIC
Click to change the image quality.
17
Change Resolution
4 CIF / CIF
Click to change the image resolution (4CIF: 704*480 / CIF: 352*240)
18
19
Remote Independent
Operation Off / On
Audio Channel Selection
Click it to disable / enable the network independent function.
Select the audio channel you want for listening to the live audio (in the live mode) or playback
audio (in the playback mode).
Note: You need to connect the camera which supports audio recording to the audio
input of the DVR. For details, please refer to “2.2 Rear Panel” at page 6.
means no camera which supports audio recording is connected to the DVR.
~49~
REMOTE OPERATION
8.3 Quick Timer Player
You can also use the QuickTime player to remotely log into the DVR and check the live view only.
Note: QuickTime is Apple’s multimedia software. You need to have QuickTime installed in you operation
system first, and you can access the DVR to see the live view.
If you have installed QuickTime, please skip Step 1.
Note: The latest version of QuickTime is V6.4 at the time this manual goes to press, and the supported
operation systems are Windows Vista / XP / 2000, and Apple Mac.
Step 1:
Go to Apple’s official website to download QuickTime. The website address is as follows:
http://www.apple.com/quicktime/win.html
a). Click “F
Free Download” to go into the download page, and select to download the free player.
b). Leave your Email address, and click “F
Free Download Now” to download the latest QuickTime player.
c). When the download is completed, execute the “Q
QuickTimeInstaller.exe” file, and follow the on-screen
instructions to finish the installation procedure.
Step 2:
Open your QuickTime player. Select “File” → “Open URL in New Player…”, and key in the URL address.
The URL format is “rtsp://ipaddress:portnum/live/h264” (For example, “rtsp://60.251.8.57:88/live/h264”).
Click “OK” to continue.
Step 3:
A pop-up window will appear and prompt you to enter the authentication information.
Key in the user name and password for accessing your DVR. The user name and password are the same
as the ones you use to log into Video Viewer. If the information is correct, click “OK” to go on. If not, click
“Cancel” to quit the accessing.
Note: If you’re not prompted to enter the authentication information, and the error message 10060
appears, go to “Edit”
“Preferences”
“QuickTime Preferences”, and select “Streaming
Transport” front he drop-down list. Select “Use HTTP”, and keep the port ID as 80.
Step 4:
When the login is successful, you will see the live view.
~50~
APPENDIX 1 PIN CONFIGURATION
APPENDIX 1 PIN CONFIGURATION
‧ For Model 1, & 4
Siren: When the DVR is triggered by alarm or motion, the COM
connects with NO and the siren with strobe starts wailing and
flashing.
Magnetic Contact: When the magnetic contact is opened, the
alarm will be triggered and the recording is on.
PIN
1
FUNCTION
GND
DESCRIPTION
GROUND
Connect ALARM INPUT (PIN 2 -- 9) and GND (PIN 1) connector with wires. Once an
alarm is triggered, the DVR will start recording and the buzzer will be on.
PIN 2 is Alarm 1. Once the alarm is triggered, the CH1 of the DVR will start alarm-triggered recording.
PIN 3 is Alarm 3. Once the alarm is triggered, the CH3 of the DVR will start alarm-triggered recording.
2~9
ALARM INPUT
PIN 4 is Alarm 5. Once the alarm is triggered, the CH5 of the DVR will start alarm-triggered recording.
PIN 5 is Alarm 7. Once the alarm is triggered, the CH7 of the DVR will start alarm-triggered recording.
PIN 6 is Alarm 9. Once the alarm is triggered, the CH9 of the DVR will start alarm-triggered recording.
PIN 7 is Alarm 11. Once the alarm is triggered, the CH11 of the DVR will start alarm-triggered recording.
PIN 8 is Alarm 13. Once the alarm is triggered, the CH13 of the DVR will start alarm-triggered recording.
PIN 9 is Alarm 15. Once the alarm is triggered, the CH15 of the DVR will start alarm-triggered recording.
10~12
PIN OFF
NA
13
EXTERNAL ALARM NO
Under the normal operation, COM disconnects with NO. But when any alarm is
triggered, COM connects with NO.
Attention: The voltage restriction is under DC24V 1A.
14
PIN OFF
NA
Connect ALARM INPUT (PIN 15 – 22) and GND (PIN 1) connector with wires. Once
an alarm is triggered, the DVR will start recording and the buzzer will be on.
PIN 15 is Alarm 2. Once the alarm is triggered, the CH2 of the DVR will start alarm-triggered recording.
PIN 16 is Alarm 4. Once the alarm is triggered, the CH4 of the DVR will start alarm-triggered recording.
15~22
ALARM INPUT
PIN 17 is Alarm 6. Once the alarm is triggered, the CH6 of the DVR will start alarm-triggered recording.
PIN 18 is Alarm 8. Once the alarm is triggered, the CH8 of the DVR will start alarm-triggered recording.
PIN 19 is Alarm 10. Once the alarm is triggered, the CH10 of the DVR will start alarm-triggered recording.
PIN 20 is Alarm 12. Once the alarm is triggered, the CH12 of the DVR will start alarm-triggered recording.
PIN 21 is Alarm 14. Once the alarm is triggered, the CH14 of the DVR will start alarm-triggered recording.
PIN 22 is Alarm 16. Once the alarm is triggered, the CH16 of the DVR will start alarm-triggered recording.
23~24
25
PIN OFF
NA
EXTERNAL ALARM COM
Under the normal operation, COM disconnects with NO. But when any alarm is
triggered, COM connects with NO.
Attention: The voltage restriction is under DC24V 1A.
~51~
APPENDIX 1 PIN CONFIGURATION
‧ For Model 2 & 6
Siren: When the DVR is triggered by alarm or motion, the COM
connects with NO and the siren with strobe starts wailing and
flashing.
Magnetic Contact: When the magnetic contact is opened, the
alarm will be triggered and the recording is on.
PIN
1
FUNCTION
GND
DESCRIPTION
GROUND
Connect ALARM INPUT (PIN 2 – 5) and GND (PIN 1) connector with wires. Once an
2~5
6 ~ 12
alarm is triggered, the DVR will start recording and the buzzer will be on.
ALARM INPUT
PIN OFF
PIN 2 is Alarm 1. Once the alarm is triggered, the CH1 of the DVR will start alarm-triggered recording.
PIN 3 is Alarm 3. Once the alarm is triggered, the CH3 of the DVR will start alarm-triggered recording.
PIN 4 is Alarm 5. Once the alarm is triggered, the CH5 of the DVR will start alarm-triggered recording.
PIN 5 is Alarm 7. Once the alarm is triggered, the CH7 of the DVR will start alarm-triggered recording.
NA
Under the normal operation, COM disconnects with NO. But when any alarm is
13
EXTERNAL ALARM NO.
triggered, COM connects with NO.
Attention: The voltage restriction is under DC24V 1A.
14
PIN OFF
NA
Connect ALARM INPUT (PIN 15 – 18) and GND (PIN 1) connector with wires. Once
an alarm is triggered, the DVR will start recording and the buzzer will be on.
15~18
ALARM INPUT
19~24
PIN OFF
PIN 15 is Alarm 2. Once the alarm is triggered, the CH2 of the DVR will start alarm-triggered recording.
PIN 16 is Alarm 4. Once the alarm is triggered, the CH4 of the DVR will start alarm-triggered recording.
PIN 17 is Alarm 6. Once the alarm is triggered, the CH6 of the DVR will start alarm-triggered recording.
PIN 18 is Alarm 8. Once the alarm is triggered, the CH8 of the DVR will start alarm-triggered recording.
NA
Under the normal operation, COM disconnects with NO. But when any alarm is
25
EXTERNAL ALARM COM
triggered, COM connects with NO.
Attention: The voltage restriction is under DC24V 1A.
~52~
APPENDIX 1 PIN CONFIGURATION
‧ For Model 3 & 8
Siren: When the DVR is triggered by alarm or motion, the COM
connects with NO and the siren with strobe starts wailing and
flashing.
Magnetic Contact: When the magnetic contact is opened, the
alarm will be triggered and the recording is on.
PIN
1~2
FUNCTION
PIN OFF
DESCRIPTION
NA
Connect ALARM INPUT (PIN 3 – 6) and GND (PIN 9) connector with wires. Once an
3~6
alarm is triggered, the DVR will start recording and the buzzer will be on.
ALARM INPUT
PIN 3 is Alarm 1. Once the alarm is triggered, the CH1 of the DVR will start alarm-triggered recording.
PIN 4 is Alarm 2. Once the alarm is triggered, the CH2 of the DVR will start alarm-triggered recording.
PIN 5 is Alarm 3. Once the alarm is triggered, the CH3 of the DVR will start alarm-triggered recording.
PIN 6 is Alarm 4. Once the alarm is triggered, the CH4 of the DVR will start alarm-triggered recording.
Under the normal operation, COM connects with NC and disconnects from NO.
7
NC
But when any alarm is triggered, COM disconnects with NC and connects with
NO.
Attention: The voltage restriction is under DC24V 1A.
Under the normal operation, COM disconnects with NO. But when any alarm is
8
NO
triggered, COM connects with NO.
Attention: The voltage restriction is under DC24V 1A.
9
GND
10
RS485-B
11
RS485-A
12~14
PIN OFF
GROUND
Using RS-485 serial communication signals, DVR can be controlled by keyboard
controller.
Using RS-485 serial communication signals, DVR can be controlled by keyboard
controller.
NA
Under the normal operation, COM disconnects with NO. But when any alarm is
15
EXTERNAL ALARM COM
triggered, COM connects with NO.
Attention: The voltage restriction is under DC24V 1A.
~53~
APPENDIX 2 COMPATIBLE USB FLASH DRIVE BRAND
APPENDIX 2 COMPATIBLE USB FLASH DRIVE BRAND
Please upgrade the firmware of the DVR to the latest version to ensure the accuracy of the following table. If the USB
flash drive is not supported by the DVR, the "USB ERROR" message will be shown on the screen.
Note: Please use your PC to format the USB flash drive as "FAT 32".
Note: You can backup up to 2GB video data for one-time USB backup. To backup more data, please set
the time & channel(s) you want, and start USB backup again.
MANUFACTURER
MODEL
CAPACITY
AH320
2G
AH320A
8G
AH220
1G
AH320
4G
A-data
RB-18
1G
Transcend
JFV35
4G
JFV30
8G
Micro Vault Tiny
1G
Cruzer Micro
2G
Cruzer Micro
4G
Cruzer4-pk
2G
MSI
F200
4G
PQI
U172P
4G
U208
1G
Apacer
Sony
Sandisk
Netac
~54~
APPENDIX 3 COMPATIBLE HDD BRAND
APPENDIX 3 COMPATIBLE HDD BRAND
Please upgrade the firmware of the DVR to the latest version to ensure the accuracy of the following table.
MANUFACTURER
Seagate
WD
Maxtor
Hitachi
MODEL
CAPACITY
ROTATION
ST3320613AS
320GB
7200 rpm
ST33500320AS
500GB
7200 rpm
ST3750330AS
750GB
7200 rpm
ST31000340AS
1000GB
7200 rpm
WD3200AAKS
320GB
7200 rpm
WD5000AACS
500GB
7200 rpm
WD6400AAKS
640GB
7200 rpm
WD7500AAKS
750GB
7200 rpm
WD10EACS
1TB
7200 rpm
WD10EADS
1TB
7200 rpm
WD15EADS
1.5TB
7200 rpm
WD20EADS
2TB
7200 rpm
STM3500320AS
500GB
7200 rpm
STM3750330AS
750GB
7200 rpm
HDT725032VLA360
320GB
7200 rpm
HDS721010KLA330
1000GB
7200 rpm
~55~
APPENDIX 4 TROUBLESHOOTING
APPENDIX 4 TROUBLESHOOTING
Please refer to the table below for easy troubleshooting. The table describes some typical problems and also their
solutions. Please check them before calling your DVR dealer.
‧ FAQ (Frequently ask question)
Questions
No power
Solutions
Check power cord connection.
Confirm that there is power supplied from the outlet.
DVR is not working when pressing any button
You might be under “Key Lock” mode. Press any key and enter the password to exit
this mode.
HDD detection failed
Replace with another HDD for testing.
Replace with another HDD cable for testing.
Can’t detect your USB flash drive
Replace with another USB flash drive for testing.
Format the USB flash drive as FAT 32 format and try again.
No live video
Confirm the camera is power supplied.
Check the setting of the camera lens.
Check the monitor’s video cable and connection.
Check the camera’s video cable and connection.
No recorded video
Check if the HDD is installed and connected properly.
Check the “MANUAL RECORD ENABLE” is set to “ON”, and the record function in
the “CAMERA” menu is set to “ON”, too.
Timer recording is not working
Check if “TIMER RECORD ENABLE” option is set to “ON” and the timer schedule
has been arranged.
Motion detection recording is not working
Check if “EVENT RECORD ENABLE” option is set to “ON”.
Check the detection function “DET” is set to “ON”.
Check the detection area “AREA” has been setup.
Can’t play the recorded data on my DVR
There must be at least 8192 images of recorded data for playback to work properly.
If not, your DVR will stop the playback.
For example, if the IPS is set to 30, the recording time should be at least 273
seconds (8192 images / 30 IPS) for the playback to work properly.
Can’t backup the video with audio
Make sure the audio cameras are connected to the DVR channels which support the
audio function.
Can’t view the DVR images over the network
with IE web browser
Check the DVR firmware version.
Failed to backup the recorded files of the DVR
from remote PC side.
(For details, please see “Network Backup” at
page 42.)
Make sure your user level is SUPERVISOR.
Please choose to allow the web browser ActiveX or applet in the pop-out message.
Check if the network connection information is correct (IP Address / Port / User
Name / Password).
Specify the hard disk (HDD Number) and channel number (Channel) within which
have the recorded data you need.
Failed to upgrade the firmware / OSD file
Check the USB flash drive is format to FAT32.
Check the firmware / OSD is correct.
Can’t use the IR remote control
Check whether if the batteries are installed or not.
Aiming at the IR receiving zone to control the DVR operation.
~56~
APPENDIX 5 RS485 PROTOCOL
APPENDIX 5 RS485 PROTOCOL
Use PC keyboards to simulate DVR keypads.
Data: REMOTE PROTOCOL uses 8 bit data, 1 start bit, 1 stop bit.
FUNCTION
CODE
ASCII
KEY_MENU
0x4D
M
KEY_ENTER
0x0D
ENTER
KEY_PLUS
0x6b
KEY_MINUS
FUNCTION
CODE
ASCII
KEY_SET_CHANNEL
0x6e
n
KEY_DWELL
0x65
e
k
KEY_CH1
0x31
1
0x6d
m
KEY_CH2
0x32
2
KEY_UP
0x55
U
KEY_CH3
0x33
3
KEY_DOWN
0x4E
N
KEY_CH4
0x34
4
KEY_LEFT
0x4C
L
KEY_CH5
0x35
5
KEY_RIGHT
0x52
R
KEY_CH6
0x36
6
KEY_POWER
0x57
W
KEY_CH7
0x37
7
KEY_REC
0x72
r
KEY_CH8
0x38
8
KEY_PLAY
0x50
P
KEY_CH9
0x39
9
KEY_SLOW
0x53
S
KEY_CH10
0x41
A
KEY_ZOOM
0x5A
z
KEY_CH11
0x42
B
KEY_KEY LOCK
0x4B
K
KEY_CH12
0x43
C
KEY_AUDIO
0x64
d
KEY_CH13
0x44
D
KEY_SEARCH
0x73
S
KEY_CH14
0x45
E
KEY_PTZ_MODE
0x70
p
KEY_CH15
0x46
F
KEY_PTZ_PRESET
0x71
q
KEY_CH16
0x47
G
KEY_PTZ_ZOOM_IN
0x69
i
KEY_EJECT_DVD
0x6a
j
KEY_PTZ_ZOOM_OUT
0x66
f
KEY_IRIS_NEAR
0x67
g
KEY_MODE
0x6f
o
KEY_IRIS_FAR
0x68
h
KEY_4 CUT
0x61
a
KEY_PTZ_LIGHT
0x6c
l
KEY_9 CUT
0x62
b
KEY_PTZ_WIPER
0x77
w
KEY_16 CUT
0x63
c
~57~
APPENDIX 6 DVR BATTERY REPLACEMENT
APPENDIX 6 DVR BATTERY REPLACEMENT
DVR time reset after power failure, for example, caused by a power outage, will cause the disorder of the recorded data,
and users may have problems in searching the event clip they want. To keep the DVR time from resetting, a
non-chargeable lithium battery, CR2032, is installed in the DVR.
However, the DVR time might still get reset when the DVR battery is low or even running out of power. If so, please
replace the DVR battery, CR2032, right away as instructed below.
How to replace CR2032
Note: The lithium battery, CR2032, is a non-chargeable battery, and should be purchased separately.
Please replace only with the same or equivalent type battery in case of danger.
Step1: Stop all DVR recording immediately to prevent the disorder of the recorded data. Then, back up the
recorded data if necessary.
Step2: Power off the DVR, and disconnect the DVR power.
Step3: Remove the DVR cover, and find the battery on the mainboard. The battery is located close to the rear
panel.
Step4: Push the release as indicated below to remove the battery.
Step5: Get a new battery with the side of “CR2032” facing up, and install it to the mainboard.
Step6: Replace the DVR cover.
Step7: Connect to DVR power, and turn on the DVR.
Step8: Set DVR date & time, and resume recording. For details, please refer to “3.4 Date and Time Setting” at page
12, and “7.1.7 Record” at page 29.
~58~
APPENDIX 7 RECORDING TIME TABLE
APPENDIX 7 RECORDING TIME TABLE
Testing Environment
The static image source as follows are input to each DVR channel with the highest image quality and IPS in each
record mode, and the video system is NTSC.
Recording Time
Please note that the recording time may vary depending on the following three factors, and the data below is for
reference only.
‧ Different camera resolution;
‧ Different picture complexity;
‧ Different frequency of the object movement
Note: For the environment with dynamic images, the actual recording time may differ from the data
below and needs to be tested based on the actual environment.
For 16CH Model
Record mode
Quality
FRAME
FIELD
BEST
CIF
IPS
GB/Hour
750GB Record Time (day)
120
1.17
26.71
240
0.977
31.99
480
3.39
9.22
IPS
GB/Hour
750GB Record Time (day)
60
0.679
46.02
120
0.643
48.6
240
1.768
17.68
IPS
GB/Hour
750GB Record Time (day)
30
1.104
28.31
60
1.062
29.43
120
1.23
25.41
For 8CH Model
Record mode
Quality
FRAME
FIELD
BEST
CIF
For 4CH Model
Record mode
Quality
FRAME
FIELD
CIF
BEST
~59~
APPENDIX 8 DVD WRITER INSTALLATION
APPENDIX 8 DVD WRITER INSTALLATION
Some DVR models allow users to install a DVD writer by themselves. To know whether your DVR supports this feature,
please check with your local distributor or retailer.
The supported DVD writer models are as follows. Please use only the suggested DVD writer models to ensure the
compatibility.
Type
Brand
Model
IDE
Liteon
DH-20A4P
SATA
Liteon
iHAS120
SONY
AD-7240S
Note: Before installing the DVD writer, make sure your DVR is powered off and your DVR supports this
feature.
For IDE DVD Writer
Step1: Remove the DVR cover, and find the DVD writer bracket to remove it.
Step2: Put the DVD writer in the bracket, and fix it to the bracket with two screws on each side.
Step3: Connect the data bus and power cables*, and make sure the jumper is set to “Slave”.
*Data bus & power cables are optional.
Step4: Replace the bracket to the DVR base and fix it.
~60~
APPENDIX 8 DVD WRITER INSTALLATION
Step5: Connect the data bus and power cables to the IDE bus and power jack on the DVR main board as illustrated in
Step1.
Note: Please make sure the power cable of the DVD writer is plugged into the black jack. This power jack
can supplied power to one hard disk and one DVD writer simultaneously.
The white jack is used to supply power to only one hard disk.
For SATA DVD Writer
Note: Before installing the DVD writer, make sure your current DVR mainboard supports SATA DVD
writer installation or not. If not, you need to install an additional SATA sub-board to support this
installation. For details, please refer to Step4 & Step5 below.
Step1: Remove the DVR cover, and find the DVD writer bracket to remove it.
Step2: Put the DVD writer in the bracket, and fix it to the bracket with two screws on each side.
Step3: Connect the data bus and power cables* to the SATA DVD writer.
*Data bus & power cables are optional.
Step4: (This step is available only when your current DVR mainboard doesn’t support SATA DVD writer installation.)
Make sure you have a SATA sub-board and a spacer support.
Note: The SATA sub-board & spacer support are optional and need to be purchased separately.
~61~
APPENDIX 8 DVD WRITER INSTALLATION
Step5: (This step is available only when your current DVR mainboard doesn’t support SATA DVD writer installation.)
Insert the spacer support and SATA sub-board to the mainboard as illustrated below.
Step6: Connect the data bus and power cables to the data bus and power jack on the DVR main board as illustrated
below.
Note: The data bus on the SATA sub-board is for HDD connection, NOT for DVD writer connection.
Please do not plug the data cable of your DVD writer to it.
Note: Please make sure the power cable of the DVD writer is plugged into the black jack. This power jack
can supplied power to one hard disk and one DVD writer simultaneously.
The white jack is used to supply power to only one hard disk.
Step7: Replace the bracket to the DVR base and fix it.
~62~
">