Table of contents
Table of contents
1.
2.
2-1.
3.
4.
5.
6.
7.
7-1.
7-2.
7-3.
7-4.
7-5.
8.
8-1.
8-2.
8-3.
8-4.
8-5.
8-6.
8-7.
9.
9-1.
9-2.
9-3.
9-4.
9-5.
9-6.
9-7.
9-8.
9-9.
9-10.
9-11.
9-12.
9-13.
9-14.
9-15.
9-16.
9-17.
9-18.
9-19.
9-20.
9-21.
9-22.
About your system
System maintenance
Remote battery replacement
LCD 2-way configuration
1-way remote description
2-way & 1-way remote function table
Standard LCD 2-way icon instructions
Programming 2-way remote
Disable remote receiving
Remote button 1.2.3 on/off
Vibrate mode on/off
Time adjust mode
Alarm clock setting
2-way signal paging features
Command Page
Alarm Page
Page Recognition (Acknowledgement)
Check-in range notification (on/off )
Reminder disarm status (Programmable)
Vehicle status checking
Turn on LCD display back light
Standard features
To ARM the system
Defective Zone Bypass & Alert
Auto Reset
Arm without siren chirp
To DISARM the system
Intrusion Alert
2-way LCD Intrusion Alert
Disarm without siren chirp
Silent arm mode
Automatic REARM (programmable)
Passive arm (programmable)
Panic mode
Dual stage shock sensor
Remote sensor by pass
Car search mode
Confort /window close
Valet mode
Ignition controlled door lock/unlock(programmable)
Ch-4: 2nd stage door unlock (programmable)
Ch-4: Remote latched (programmable)
Passive immobilizer (programmable)
Arming without Remote control (programmable)
-1-
Page
3
4
4
4
5
5
6
9
9
9
9
10
10
11
11
11
11
12
12
12
12
13
13
13
13
13
14
14
14
15
15
15
15
16
16
16
17
17
17
17
17
17
18
18
9-23.
9-24.
9-25.
9-26.
9-27.
9-28.
9-29.
9-30.
9-31.
9-32.
9-33.
9-34.
9-35
9-36.
9-37.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
2nd step disarm
Remote trunk open
CH-5: Dome light supervision
CH-5: Arm W/Engine running
CH-5: Turbo mode
CH-6: Programmable output
CH-7: Programmable output
Red/black programme (+) input
- Reverse warning
- Heard light warning
- Extra sensor (knock sensor) input
Siren chirps ON/OFF (programmab le)
Status LED timer
Power disconnecting memory
Emergency reset switch
Emergency disarm (Valet SW & PIN code)
Anti car-jacking mode
R.f antenna call switch
Set your own PIN code
Transmitter programming
Programme mode features
Programme mode table
System installation
Wiring diagram
Central door lock wiring
-2-
18
19
19
19
20
20
20
20
20
20
20
21
21
21
21
21
22
23
23
24
24
25
27
28
30
About Your System
Congratulations on your purchase of this state-of-the-art vehicle security system.
With proper installation this system will provide superior protection and performance for
many years to come.
What is included:
A control module
2-way pager transceiver antenna
One 5-button 2-way LCD remote transmitter
One 3-button or 4-button random code remote transmitter
Dual stage shock sensor
High output 6-tone siren (optional)
Status LED indicator
Valet over-ride switch
Options and Accessories:
This system includes several optional inputs and outputs allowing the creation of a
completely personalized security and convenience system by offering many optional
features such as:
2nd stage door unlock
Horn honk output
2pulse signal door unlock
Engine turbo time mode
Check range notification
Arm/disarm chirp on/off
Window close control
Anti car-jack by door switch
Power trunk/hatch release
Glass breakage sensor
Micro-wave detector
Back-up battery sirem
*Many require additional parts and/or labor, see store for details
NOTE:
Some of the features described in this manual may required additional parts and/or
labor, and may not be included as part of the standard installation of this unit.
Additionally, many features of this security system have selectable options that must be
activated or programmed during the system's installation. These items will be identified
in the following sections. Please discuss these features and any questions you may
regarding the installation of this product with your authorized dealer.
-3-
System maintenance
The system requires no specific maintenance other than battery replacement for the remotes.
LCD 2-Way Remote Battery Replacement
The 2-way remote is powered by a 1.5V AAA battery. The Battery Level indicator has three level
indicators that serve as a visual indication of battery charge. When the battery reaches a low
charge level that requires replacement, the transceiver will generate a single notification chirp,
and the Battery Level indicator will flash continuously.
FULL
REPLACE
EMPTY
To replace the battery, gently pull the battery cover release tab, then slide the door down to
expose the battery and remove the expired battery. Place the new battery into the transceiver
observing the correct polarity. When power is returned the transceiver will light all icons in the
LCD and generate all beeper tones once.
3 & 4-Button Remote Battery Replacement
Your remote is powered by a 12V A27 that will last approximately one year under normal use.
When the battery begins to weaken, operating range will be reduced and the LED on the remote
will dim.
LCD 2-Way configuration
Antenna
Button 3
LCD screen
Button 4
Button 5
Button 2
Button 1
NO: TR-44LCD
-4-
1-Way Remote Transmitter Description
LED indicator
Button 1 (Arm / Door lock)
Button 2 (Disarm / Door unlock)
Button 3 (Trunk open)
Button 4 (Silent arm mode)
NO:
TX-4R
2-way & 1-way Remote Function Table:
Functions
Step
Arm and door lock
Press
once
Arm without siren chirp
Press
once then within 3sec. press
Condition
Disarmed & ACC off
once
Disarmed & ACC off
Disarm and door unlock
Press
once
Disarm without siren chirp
Press
once then within 3sec. press
Trunk open
Press
over 2sec
Anti car-jack mode
Press
Panic mode
Press
over 2sec.
Armed
Car search mode
Press
once after 8sec. of armed
Armed
1st stage sensor bypass
Press
once within 8sec. of armed
Armed
2nd stage sensor bypass
Press
once within 8sec. of armed
Armed
Valet mode
Press
together over 2sec.
Status check & Back light
Press
once
Remote button 1.2.3 on/off
Press
over 2sec.
Silent arm mode
Press
once. & Press 1-way
Enable check-in range
Press
once within 8sec. of armed.
Vibrate mode on/off
Press
over 2sec.
Armed
once
Any time
ACC ON
together over 2sec..
Disable remote receiving
Press
together over 2sec.
Time adjust mode
Press
together over 3sec.
Alarm clock setup
Press
together over 3sec.
-5-
Armed
ACC ON
once.
Disarmed
Armed
Standard LCD 2-way icon instructions
Remote transmitting a signal.
Check-in range turn ON status.
Weak signal notification.
T
R
System Armed.
System Disarmed.
Silent Armed.
Passive arming &
Auto re-arming mode.
1st-stage sensor bypass.
2nd-stage sensor bypass.
X
PASS
Panic mode.
Door open when armed.
-6-
X
PASS
Trunk open when armed.
Hood open when armed.
1st stage sensor triggered.
2nd stage sensor triggered.
Door switch triggered.
Trunk switch triggered.
Hood switch triggered.
Ignition switch triggered.
Passive immobilizer mode.
Anti car-jacking mode.
AHJ
IMMO
Valet mode.
Arm W/engine running mode.
-7-
Turbo mode.
Call / page mode.
2way receiving OFF mode.
2way button OFF mode.
2way time display.
Alarm clock.
CALL
2way Vibration mode.
AM
Extra sensor triggered.
(Knock sensor) optional
Hand brake indication.
(Optional for starter model)
BRAKE
-8-
AM
2way battery level indication.
Programming 2-way remote
Disable remote receiving
You may turn off the 2-Way remote receiving signal from the main unit. Press button
simultaneously for 2sec. until one long beep is heard. Remote receiving is now
disabled. To turn on receiving again, Press button
simultaneously until two long
beep is heard, remote receiving is now enable.
2-way LCD display :
2way remote button ON/OFF
For safety purpose, this 2-way remote can be lockout the remote button in order not to
mis-touched the buttons. Press button
for over 2sec. until one beep is heard, remote
button is now locked. To turn on remote button, press button
for over 2sec. until two
beeps is heard, remote button is now unlocked.
2-way LCD display :
Vibrate mode on/off
Press button
the button
for over 2sec. the 2-way remote will respond tone & vibrate feature,
pressing 2sec. will change the feature, see under table:
Beeps
1-beep
Vibrations
2-way remote feature
1-time
Remote with tone and vibration
1-time
Remote with vibration only
1-beep
Remote with tone only
If set with vibration only
the 2-way LCD will display :
-9-
Time adjust mode
Besides operating for alarm functions, LCD remote control additionally provides 12-hour
clock, alarm clock.
Instructions:
1. Press and hold Button
for 3sec. to enter time-setup mode, 1 beep will be heard.
2. Press button
to select Hour & Min adjust setting. Icon flashing to indicate.
AM/PM indicator
AM
PM
12-hour display
Minutes display
3. Press button
to turn up the numbers. Press button
to turn down the numbers.
The button may be held down to scroll faster.
4. Press button
to exit the setting mode. 2 beep will be heard.
Note: The remote will revert to normal operation from the set mode when 10-seconds has
elapsed without a button entry.
Alarm clock setting
This function useful to warning the user by pre-setting alarm clock time, if setting time up,
the LCD remote will give beep sound for 1 minutes. (Press any button once will stop beep).
Instructions:
1. Press button
for 3sec. To enter alarm clock time-setup mode, 1 beep sound will
be heard and alarm clock icon flashing:
AM
PM
2. Press button
to select Hour & Min adjust setting. Icon flashing to indicate.
3. Press button
to turn up the numbers. Press button
to turn down the numbers.
The button may be held down to scroll faster.
4. Press button
to enable the alarm clock. 1 beep will be heard and exit the mode.
Press button
to disable the alarm clock. 2 beep will be heard and exit the mode.
Note: The remote will revert to normal operation from the set mode when 10-seconds has
elapsed without a button entry.
-10-
2-way signal paging features
A page is the signal the control module sends to the remote controls confirmation of
receipt of a command or alarm system status. When the remote control receives a page
it will generate a page notification to the user (notifications are audible beeps) and the
LCD Icons will display the current system status.
Command Page
When a command (arm/disarm, or auxiliary channel) from the remote control is sent
and received, the system will send a command page back to confirm receipt.
Alarm Page
If the alarm system is triggered while armed, an Alarm Page will be sent to the remote
control. When the remote receives an Alarm Page, the LCD icons will display the alarm
system status information and the remote control will generate beeps.
Display
Beeps
5 short
Vibrations
1 times
Trigger
1st stage-Sensor warning
Melody 1 1 times periodically
2nd stage-Sensor triggering
Melody 2 2 times periodically
Trunk switch triggering
Melody 3 3 times periodically
Door switch triggering
Melody 4 4 times periodically
Hood switch triggering
Melody 5 5 times periodically
Ignition triggering
Page Recognition (Acknowledgement)
To clear a page alert/notification, quickly press any button on the remote control. This
can be performed at any time during or after the page notification has occurred.
The remote control will not send a command to the system at this time; it will only clear
future repeats of the page notification. The next time a button is pressed on the remote
control it will send a command to the system.
-11-
Check-in range notification (on/off )
Arming the system within 8-seconds, press button
system will enable this Check- in range function.
The 2way remote
will respond:
R
once on the 2way remote , the
Icon will on for 2sec. and give 1 beep
sound to indicate the function has been
turned ON.
- With in 5 minutes, the 2-way remote will than give 1 beep sound every one minute for 5
cycles to remind the user within range.
- After 5 minutes , the Antenna icon will indicates under receiving status:
Full reception
Half reception
Weak signal
Non reception
(flashing icon)
For friendly usage, the 2-way remote will provide 2 beeps/ 3cycles and flashing icon
after 35 minutes if the user is out of the receiving rage. However, afterwards if the 2-way
remote detect the signal again from the system, 1 beep sound will be provided and flashing
icon
will be ON to indicate the 2-way remote is within range.
Note: If under Check-in range mode, if alarm triggered, this function will automatically
turn off (disable).
Reminder disarm status (Programmable)
If programmed with " 1way reminder disarm status to 2way" feature , this function will
reminder disarm status if disarming by 1-way remote control. The 2-way remote will display
disarm icon and give 2 beep sound .
Vehicle status checking
The 2-Way remote offer the feature to check the current status of the car, simply press
button
once within proper operation range. The main unit will send the signals to
the 2-Way remote about the vehicle current status.
Turn on LCD display back light
Simply press button
once, the back light of LCD display will turn on 5 seconds and
also check the vehicle status.
-12-
STANDARD FEATURES:
- To ARM the system:
To arm your system within proper operation range, simply press button
once (while system
in disarmed or Acc off position) . The system will respond one siren chirp, one lights flash,
doors lock, disable engine starter, LED will begin flashing quickly until all sensor inputs are active
- LED will start blinking slowly (flash once per second) to indicate the system is in full armed.
+ One beep sound
2-way LCD display :
- Defective Zone Bypass & Alert:
If the security system is armed at the same time that an input is active (such as a door opening
or hood / trunk opening ), you will hear one siren chirp to indicate arming and after 8 seconds
a second siren chirp to indicate Bypass Notification. A Bypass Notification chirp means that the
security system ignores the input that was active when the system was armed, until that input
ceases.
Defective zone
Siren chirps
2-way beeps
Door opened
3 chirps
1 long + 3 short
Trunk opened
4 chirps
1 long + 4 short
Hood opened
5 chirps
1 long + 5 short
Note: You may press 2-way remote button
2-way LCD indicator
once to check again which zone is not closed.
- Auto Reset:
If a violation occurs the system will respond by sounding the siren and flashing the lights for
approximately 30sec. before the system resets itself and continues to protect your car. If violation
still occurs the system, siren and lights will working for 8 cycles then the system reset itself and
continues to protect other zones.
- Arm without siren chirp :
You may temporarily to arm your system without siren chirp , to operate it by simply press button
once then within 3sec. press button
once.
The system will armed and without one siren chirp,
Note: this features is only activated under the system is in disarmed and Acc off position,.
-13-
- To DISARM the system :
To disarm your system within proper operating range, simply press button
once (while
system in arm position). The system will respond two siren chirp, two light flash, doors unlock,
Enable your engine starter, LED off.
+ Two beep sound
2-way LCD display :
- Intrusion Alert:
Upon disarming the system, if the vehicle is attempted or intruded, siren and lights will Indicates
4 chirps and 5 flashes to identify which zone was triggered. LED mode indicates the following
different triggering.
flash 2 times after a pause
Sensor 1st-stage triggered
flash 3 times after a pause
Sensor 2nd-stage triggered
flash 4 times after a pause
Door switch triggered
flash 5 times after a pause
Trunk switch triggered
flash 6 times after a pause
Hood switch triggered
Flash 7times after a pause
Ignition switch triggered
- 2-way LCD Intrusion Alert:
Upon disarming the system, if the vehicle is attempted or intruded, the 2-way remote will respond
2 short beep follow with melody sound, and LCD display will indicates different icons as under:
1st-stage sensor
triggered
Trunk switch triggered
2nd-stage sensor
triggered
Hood switch triggered
Door switch triggered
Ignition switch triggered
Note: Before the ignition turn on, you may realized again which zone been triggered by press
button (status check) once, the LCD will display triggered zone again.
-14-
- Disarm without siren chirp :
To disarm your system without siren chirp , simply press button
once then within 3sec.
press button
once.
Note: this features is only activated under the system is in armed position,.
- Silent arm mode :
The system provide a feature to turn OFF the siren, simply press 2-way button
of press
1-way button
once (while system in disarmed or Acc off position) . The system will
respond one lights flash, doors lock, disable engine starter, LED will begin flashing quickly
until all sensor inputs are active - LED will start blinking slowly (flash once per second) to
indicate the system is full armed.
2-way LCD display :
+ One beep sound
Note: Under Silent Arm mode, if Sensor, Door, Hood or trunk been triggered, the siren will
not activated, but if Ignition been triggered will activated the siren.
- Automatic REARM (programmable):
If the system is disarmed by remote and a door is not opened within approximately 30
seconds the system will automatically rearm itself. This feature guards against disarming
caused by accidental or unintended operation of the remote transmitter. Main unit will
sends signal to the 2-Way LCD remote and indicates ARM mode with one beep sound.
Flashing icon to indicate that the
system is in Auto re-arming mode.
2-way LCD display :
Flashing
- Passive arm (programmable):
If set programme mode to "WITH", while turn Ignition OFF, then close the last door ,system
will provide 2 siren chirp and 2 light flash and LED flashing fast to indicated that the system
is in passive arming mode. After 30sec. The system will arm by itself and LED flashing slowly
to show the system is in arming mode. Main unit sends the signal to the 2-Way LCD remote
and indicates ARM mode with one beep sound .
This system also provide under passive arming with door lock or without door lock
feature (please see "programme mode" features. ) During the period of 30sec. passive
arming, if a door is opened, Led will light on and it will re-passive arming when the door
closed again.
Two beep sound will provided to
to indicate that the system is in
Passive arm mode.
2-way LCD display :
Flashing
-15-
- Panic mode:
If you are threatened in or near your vehicle, you can attract attention by press button
for 2sec. system will triggering for 30sec. To stop Panic mode at any time, simply press
any button once.
Note: if Panic mode activate in disarmed position, the 2-way remote will respond melody
sound and LCD indicates flashing icons as under:
Under Panic mode, the 2-way remote
will respond melody sound and
flashing icons .
2-way LCD display :
- Dual stage shock sensor:
This device only activates after 8 seconds of arming state; this is preventing from the
weak impact caused by the driver while leaving the car.
The device operates:
-Light impact will activate the 1st stage sensor by giving 5 short warning chirps. 2-way
remote will respond 5 beeps and flashing icon as under.
2-way LCD display :
+ 5 beeps sound
Note: This paging feature is
can be programmed to
With or Without .
-Heavy impact will activate the 2nd stage sensor and trigger the alarm for 30sec. 2-way
remote will respond melody and flashing icon as under.
2-way LCD display :
+ Melody sound
NOTE: Adjustments are made via the rotary control above the shock sensor.
- Remote sensor by pass :
This system offer 2stage sensor optional. Within 8sec. after set arming, to press button
once , the system will give 2 short chirps and 2 lights flash, thus the 1st stage shock
sensor has been turn off.
Press button
once again, within 8sec. the system will give 3 short chirps and 3 lights
flash, thus the 2nd stage shock sensor has been turn off.
If press button
once (at 3 times) again within 8sec. of arming the shock sensor will
turn ON again.
1st stage sensor bypass.
X
2nd stage sensor bypass.
X
PASS
PASS
2-way LCD display :
Note: - if remote sensor bypassed, it will be detected again by next arming.
- if armed with silent mode, to operate sensor bypass will only indicate by lights flash.
-16-
- Car search mode:
The system provide a feature to easy find your car position, simply press button
when in armed after 8sec. The system will respond by 5 chirps and 5 lights flash.
once
-Comfort /window close :
This channel "White/black wire" is a negative (-500mA) output features, this feature can be
controlled " window close when arming". This function will constant output for 30sec.
When arming the system. Note: sensor will be bypassed when this channel is activating.
- Valet mode:
To enter valet mode: Disarm the system and turn Ignition switch to ON position then press
button
+
for over 2 seconds, or press Valet/over-ride switch for over 5 seconds, until
siren give 1 long with 1 short chirp and LED light ON to confirm the system is in valet mode.
Note:
Under Valet mode, each time
turn Acc off , the siren will give
2 chirps for notification.
2-way LCD display:
When the system is in the valet mode it can not be armed. The door lock and unlock will
function as keyless entry system.
To exit valet mode:
Turn Ignition switch to ON position , then press button
+
for over 2seconds, or press
Valet/over-ride switch for 5 seconds. You will hear siren provide 1 long with 2 short chirps
and LED light OFF to confirm exit this mode and in alarm mode. The 2-Way remote will
respond 1 long and 2 short beeps.
- Ignition controlled door lock/unlock(programmable):
If programmed with this feature, turn Ignition ON after 10 seconds the doors will auto
locked , but within this 10 seconds the door has been opened this feature will bypassed,
till next time of ignition on.
When turn Ignition OFF, the doors will unlock for take off, if programmed with ignition off
door unlock.
Note: You may manage lock and unlock doors in ignition on position by short pressing
button
to lock door or pressing
to unlock door.
- Channel -4 (-) output (programmable):
This channel Yellow/black wire" is a negative (-500mA) output features, this feature
can be controlled " 2nd stage door unlock / Remote latched ".
2nd stage door unlock:
If programmed with the feature , to operate it by press button
at 2nd time , 2nd stage
door unlock will be output for passenger side .
Remote latched:
If programmed with the feature, to operate it when ignition off, press button
for over
2 seconds, siren will give 1 chirp and the Channel will constant output.
To exit by ignition off and press button
over 2 seconds, siren will give 2 chirp and
the channel will stop output.
-17-
- Passive immobilizer (programmable):
If programmed with this function, when turn off ignition switch for 30 seconds or you open
and close the door, it will disable the engine starter right way . The LED will flash twice
per second.
IMMO
2-way LCD display :
IMMO
+ One beep sound
Exit: To disarm this function by (1) simply press button
once. LED off.
Note: Under this mode, if ignition force been turn ON , siren will give 1long + 1 short chirps
warning, 10seconds later will activate the alarm, the 2way remote will indicate Anti
car-jack icon and warning sound. To disarm it with programmed "Valet SW or PIN
code " feature. (Please see Emergency disarm.)
- Arming without Remote control:
This function gives you a possibility to Arm and Disarm the system without remote control.
Note: if programmed with Passive arm feature, this feature will not activated.
- To activated arm without Remote control :
(1)
(2)
(3)
(4)
After driving and ignition keep ON.
Open a door, and keep it opened.
Turn ignition OFF and within 10seconds. press Valet switch once.
within 15 seconds, close door, the system will arm immediately.
- Disarm without Remote control:
Delay of alarm only available to activate while you have successfully enter into Arm W/O
RC mode ., within 20 seconds after opened the door or trunk switch. It allows you after
opening the door, to seat in to the car and enter 1st digit of PIN code. (10 seconds delay
st
time for Ignition turn on to set 1st PIN code). If within (10) seconds you didn't enter 1 digit
PIN code or insert wrong PIN code , the system will alarming., To re-set the system may
required only 2 digit PIN CODE (See "How to use your PIN code" ).
If programmed without PIN code, to disarm it by turn ignition on then press and hold the
Valet switch for over 5 seconds.
Note: To exclude unauthorized entering in to the car, pager output will activate immediately
after opening the door despite of the switched on delay of alarm mode.
- 2 step disarm:
This system offers 2 step disarm. It's a feature that make it possible to silence and reset
the system while it is triggering, without disarming the system. If the system is triggered
and the siren has been sounding, pressing any button once on the remote transmitter will
stop the trigger and return the unit to the armed state.
Note: Under system triggering, if press any button of 2-way remote once , the remote will
stop the beep sound and LCD display will indicate the intrusion icon for 2sec.
Press any button again to stop alarm triggering.
-18-
- Remote trunk open:
Simply press and hold button
over 2 seconds, the channel will output for 1 second pulse ,
to open the trunk. When armed if remote trunk open or close, the system will give one light
flash and the 2-way remote will give one beep sound. The 2-way LCD display icon as under:
2-way LCD display :
Note: (1) Ignition ON does not allow to remote trunk
open, unless one door is opened.
(2) Armed, if trunk opened over 1 minutes, the
2-way remote will give pre-warn beep sound.
Note: If trunk has been remote opened in arming position, trunk switch will delay sensing for
5 seconds, and the shock sensor will be bypassed.
- Channel-5 (-) output(programmable):
This channel "Gray/black wire" is a negative (-500mA) output features, this feature
can be controlled " Dome light output / Arm W/Engine running / Turbo mode) ".
Dome Light:
If programmed with the feature , the channel will constant output 30sec. when disarming .
Turn ignition switch ON will stop the channel output.
Arm W/Engine running:
If programmed with the "Arm W/Engine running, this feature for the car to keep engine
running after arriving at your destination.
To operate this feature by pressing
for 2sec. while driving or ignition ON , the
siren will give one chirp and the LED will start flashing Green color, at the time the system is
in standby mode, the owner must follow under process to activate the "Arm W/Engine
running " mode.
(1) Within 30sec. Turn Ignition OFF (engine still keep running), open and close door to
leave the car.
Note: If within this 30sec. not leave the car by door open close, will exit the mode.
(2) While leaving the car by open and close the door, within 15sec. :
if press button
once, to enter engine running mode without time limited.
if press button
once, to enter engine running mode with time limited.
While the system in engine running mode , The parking lights will flash once every 5 sec.,
and the status LED will flashing Green color.
The 2-Way remote will respond under icons flashing as long as turbo time finished.
Note:
(1) After leaving the car, within 15sec.
If press wrong button will exit mode.
(2) After leaving the car, within 15sec.
If without press
button will exit
mode automatically.
2-way LCD display :
Exit mode :
Pressing button
once of the remote control within engine running mode , the system
will delay 30 seconds and exit turbo mode, this delay time is allow the user using the key
turn ignition on without stop the engine running.
NOTE: 1. In engine running mode, the sensor zone trigger will be bypassed.
2. In engine running mode, if door, hood or trunk has been triggered, engine will
stop running and alarming the system, simply press button
to disarm .
-19-
Turbo mode:
If programmed , the CH-5 channel will constant output when ignition turn on 1 minutes. It will
keeps the engine running after arriving at your destination by ignition off for a programmed
time 1/ 3/ 5/ 10 minutes. This allows the system's timer to conveniently cool down the turbo
after you have left the vehicle.
2-way LCD display
when armed:
NOTE:
you may disable this turbo mode
after ignition turn off ,by press
button
once, the CH-5 will
stop outputting.
Flashing icon
Note: in turbo mode time , if arming the system, sensors will be bypassed and LED flashing
Green color for a programmed turbo time.
Important: Turbo mode should be used only in open areas. Never start and run the vehicle
in an enclosed space such as a garage or carport.
- Channel-6 (-) output(programmable):
This channel "Brown/black wire" is a negative (-500mA) output features, this channel can be
programmed : (1)- Arming output 1~120sec. (2)- Press button
+
output 1~120sec.
(1)- Arming output 1~120sec. if programmed, this channel will activate when arming, the
output timing can be programmed from 1 to 120seconds.
(2)- Press button
+
output 1~120sec. If programmed, to operate this channel by press
button
+
for over 2sec. This channel will constant output for programme time.
Note: When this channel is outputting, if press button
+
once, it will stop outputting.
- Channel-7 (-) output(programmable):
This channel "Black/white wire" is a negative (-500mA) output features, this channel can be
programmed : (1)- Disarming output 1~120sec. (2)- Press button
+
output 1~120sec.
(1)- Disarming output 1~120sec. if programmed, this channel will activate when disarming,
the output timing can be programmed from 1 to 120seconds.
(2)- Press button
+
output 1~120sec. If programmed, to operate this channel by press
button
+
for over 2sec. This channel will constant output for programme time.
Note: When this channel is outputting, if press button
+
once, it will stop outputting.
- Red/black programme (+) input:
This red/black (+) positive input can be programme three feature as:
- Reverse warning : If programmed , connect to the (+)reverse back light. when you are
-
reversing your car the siren will give a short warning chirp every one second.
Note: you can proceed the Reverse warning without siren chirps : (1) when you activated
the Disarm w/o chirp before Ignition On. (2) when you reversing the Car simply press
the button
once.
Head warning : If programmed , connect to the (+)head light . This feature will provide
pre-warning chirps if you forgot to turn off the head light while leaving the car.
Extra sensor (knock sensor) : If programmed , connect to the (+) optional extra
sensor ( knock sensor). This feature will paging the 2way remote while trigger the sensor.
+ Melody sound
2-way LCD display :
-20-
- Siren chirps ON/OFF (programmable):
This programme feature controls the chirps that confirm the arming , disarming and
intrusion alert of the system.
Note: Set siren chirp off, if door, hood or trunk not closed, siren will activated.
- Status LED timer:
If the alarm system armed after 24 hours, the LED will blink shortly once per second.
Armed after 25~48 hours, the LED will blink shortly once every 3 seconds.
Armed after 48 hours, the LED will blink shortly once every 5 seconds.
- Power disconnecting memory :
Alarm is built in memory on main unit. Generally, after alarm power is cut off and reconnect,
main unit will read back these data make the alarm to resume. When in disarm, arm or
valet mode position, power off then on , alarm will read back original position.
Note: while power on of the system, the parking lights will flash twice for indication.
- Emergency reset switch: (for installer only)
If the remote has been lost or damage, or forgot the PIN code number the owner can enter the
car by using the key. It will act the alarm. To disarm the alarm turn ignition on and connect
"reset switch" for over 2sec. , it will disarm the alarm immediately. (Please ask your installer
this reset switch location).
Note: after this emergency reset activated, the PIN code will resumed factory setting
PIN code " 2 . 5 "
Emergency disarm (Valet SW & PIN code):
If the remote control has been lost or damaged, you can manually disarm your system by
programmed " Valet SW or PIN code":
Emergency disarm by Valet Switch :
(1) Turning the Ignition switch from OFF to ON position.
(2) Simply pressing and holding the Valet switch for over 3 seconds, the system will
disarmed immediately.
Emergency disarm by PIN code :
(The system's factory-set PIN code is "2 . 5" )
(1) Turning the Ignition switch from OFF to ON position.
(2) The LED will start flashing, the times of LED flashing is according to the 1st PIN code
numbers.
(3) While the LED flashing 2 times then turning the ignition switch to the OFF position, thus
the 1st PIN code has been inserted.
(4) Turn the ignition to ON again, the LED will start flashing again, while flashing 5 times
then turning the ignition the OFF position, thus the 2nd PIN code has been inserted.
(5) After 2 digit PIN code has been correctly inserted, the system will disarmed immediately
and siren will give 4-short chirps.
NOTE: Each cycle of alarm triggering is only provide one time to set PIN code, otherwise
the owner must wait next cycle triggering and then set PIN code again to disarm the system.
If the owner forgot the PIN code number, must use "Emergency reset switch " to reset the
alarm system (please see "Emergency reset switch" ).
-21-
Anti Car-Jacking mode:
This feature will protect your vehicle in the event that there is an attempt to Hi-jack the
vehicle. The system provide two ways to activate the Anti car-jacking mode if programmed.
While system is trigger anti-car jack mode, lights will flash once and the LED will fast
flashing to show the system is enter anti-car jacking mode. see "anti-car jack mode table".
Remote activates:
If programmed, to operate it when driving the car (ACC ON), press button
for
2 sec. The parking lights will flash once and the LED will fast flash to show the system is
entering anti car-jack mode.
Door switch activates:
If programmed, to operate it when driving the car, if a door is forced been open and close,
the system will activate Anti-car jack immediately. The parking lights will flash once and the
LED will fast flash to show the system is enter anti car-jack mode.
AHJ
2-way LCD display :
AHJ
-Anti car-jack mode table:
If enter anti car-jack mode, Parking lights will flashing once and the LED will fast flashing
to show the system is enter anti car-jack mode.
While proceed at 60sec. main unit sends signal to the 2-Way remote and respond
flash AHJ icon give melody sound.
AHJ
2-way LCD display :
+ melody sound
AHJ
Flashing
LED flashing fast
LED flash
1 flash
Lights flashing once per second
Lights flash
Pre-warning
Siren blowing
Siren chirp
Immobilizer-1 blocked
Immobilizer-1
2nd killer blocked
Immobilizer-2
Timer
0sec.
20sec.
40sec.
60sec.
100sec.
Exit Anti car-jack mode:
1- Within 60sec: After entering this mode, simply press any button of the remote control
in ACC on position, siren will give 4 chirps and LED will off to confirm
exit this anti car-jacking mode. 2-way remote will give 2 beep sound.
2- After 60sec: To exit this mode with programmed Valet SW or PIN code , please see
( Emergency disarm by Valet SW & PIN code).
-22-
R.F Antenna CALL SWITCH :
The R.F antenna module provide a switch which can be
send a signal to the 2-way remote.
In disarmed or ACC on position, if press Call switch for
2 seconds, lights will flashing 5 times and the 2-way
remote will give pre-warn beep sound . The vehicle
page mode icon displays when the alarm module is
paging the transceiver.
CALL
CALL
Call switch
Set your own PIN code :
The system provide 2 digit PIN code and it can be programme your own PIN code.
Whenever you set your own PIN code of the system, the procedures are as following:
1. Enter Valet mode, the LED on status.
2. Keep a door opened.
3. Turning ignition switch ON to OFF for 3 times within 10sec. , and steady in OFF
position, siren will provide 1 long chirp.
(Each time ignition switch turned off, siren will give 2 chirps for indication)
4. Now you have insert your former (old)PIN code to release this programming
mode. For example your old PIN code is "2.5", turn ignition ON , LED start
flashing (the times of LED flashing is according to the 1st PIN code), While LED
flashing 2 times then turn ignition OFF, thus the 1st PIN code entered.
Turn ignition ON again, LED start flashing, while it flashing 5 times then turn
ignition OFF, thus the 2nd PIN code entered.
If the 2-digits PIN code entered correctly, the siren will provide 2 long chirp and
LED off . System now is in the new PIN code programming mode.
Note: If enter not correct PIN code, siren will give 2 short chirps and exit this
mode and back to Valet mode. Please repeat procedure step # 4 again.
5. Follow from 2-long chirp, the system under new PIN code setting mode.
Suppose to set new PIN code : ( 3 . 8)., Turn ignition to ON , at time the LED will
start flashing (the times of LED flashing is according to the 1st PIN code), While
LED flashing 3 times then turn ignition OFF, thus the 1st PIN code been
programmed.
Turn ignition to ON again, LED start flashing, while it flashing 8 times then turn
ignition OFF, thus the 2nd PIN code been programmed.
6. At the time system of Led will indicating to identify the New Pin code.3.8 (3 flash
Pulse then 8 flash). Siren will give 2 short chirps to identify the new PIN has been
programmed.
7. Then system existed new pin code setting and return back to the Valet mode.
-23-
Transmitter programming:
This programming features is provide the owner to learn the new transmitter into the system
memory. This system can expand 4 different transmitters, and comes from factory with two
transmitters already programmed into the system memory (1-way & 2-way ) .
Whenever you want to add or delete transmitter code , the procedures are as following:
1. Enter Valet mode, the LED on status.
2. Keep all door closed.
3. Turning ignition switch ON to OFF for 3 times within 10sec. , and steady in OFF position,
siren will provide 3 long chirp.
(Each time ignition switch turned off, siren will give 2 chirps for indication)
4. Now you have insert your former (old)PIN code to release this programming mode.
For example your old PIN code is "2.5", turn ignition ON , LED start flashing (the times
of LED flashing is according to the 1st PIN code), While LED flashing 2 times then turn
ignition OFF, thus the 1st PIN code entered. Turn ignition ON again, LED start flashing,
while it flashing 5 times then turn ignition OFF, thus the 2nd PIN code entered.
If the 2-digits PIN code entered correctly, the siren will provide 1 long chirp and the LED
will flashing fast to indicate that the system is in Learning mode.
Note: If enter not correct PIN code, siren will give 2 short chirps and exit this
mode and back to Valet mode. Please repeat procedure step # 4 again.
5. Follow from 1-long chirp, LED flashing fast, It's available to learn the new transmitter into the
system by press any button once of the new transmitter, siren will give 1-long and 1-short chirps
to indicate the first transmitter code learn into the system memory.
To learn the 2nd,3rd,4th new transmitters, simply press any button once on the each transmitter,
the numbers of siren short chirps is according to the numbers of the new transmitters learn into
the system memory . (Each time learning new code of remote, the old code will be erased, hence
you have to learn again.)
6. To exit this programming mode, if there is no new transmitters button been pressed, turn ignition
to ON or within 20 seconds without any button pressed , siren will give 2 short chirps and back
to the Valet mode.
Programme mode features:
Many of the operating settings of this unit are programmable. The programmable mode setting
dictates how the unit operates.
To enter programme mode and access Feature Change:
1. Disarmed the system, turn ignition from ON to OFF, within 10 seconds press valet Switch
ON-OFF for 5 times.
2. Siren will 2 long and 2 short chirps. Then turn the ignition switch to ON, and LED will steady
ON to confirm the system is in programme mode.
3. To press the
button : select the item number , each time the
button is pressing, siren
will give a different chirps sound to confirm.
4. To press the
button: select the feature status, press the
button , siren will give short
chirp to confirm the feature has been programmed.
Exit programme mode:
Under programming mode, if turning Ignition to OFF , the system will exit the programming mode
and siren will give two short chirps .
-24-
I
PROGRAMME FEATURES TABLE:
Press
Item NO:
LED flash
Siren
chirp
confirm
Press
FEATURES
once Press
1-chirp
twice Press
2-chirp
1
Ignition controlled doors lock
*W/I
W/O
2
Ignition controlled doors unlock
*W/I
W/O
3
Automatic re-arm
W/I
*W/O
4
Siren & Horn pulse output
*Siren
Horn
5
Arm / Disarm siren chirp on/off
*ON
OFF
6
Passive arming & door lock
7
W/I
W/I
With door lock
Without door lock
Passive immobilizer
W/I
*W/O
8
Anti car-jack by Remote activation
W/I
*W/O
9
Anti car-jack by Door switch activation
W/I
*W/O
10
CH-4 (2nd stage unlock / Remote latched) 2nd stage
11
12
unlock
*Remote
latched
Manage Door lock/unlock (Time/Pulse)
*0.8sec.
4sec.
Door switch arming delay 3 / 45 second
*3sec.
45sec.
for siren short pulse
for siren long pulse
-25-
3 times Press
3-chirp
4 times
4-chirp
*W/O
2pulse
unlock
Lock 30sec.
Unlock 0.8sec.
Press
Item NO:
LED flash
Siren
chirp
confirm
Press
FEATURES
once Press
13
1-way Reminder disarm status to 2-way
*W/I
14
CH-5 (Dome light/Engine run/Turbo mode)
Dome light
15
Turbo mode & Arm with engine runing
twice Press
2-chirp
1-chirp
3 times Press
3-chirp
4 times
4-chirp
W/O
*Arm With
Engine Turbo mode
running
*1 minute
3 minute
5 minute
10 minute
time setting
16
Emergency disarm by (Valet SW/ PIN code) *Valet SW
17
1st-stage sensor trigger W/2way report
18
Ignition turn ON W/2way report
19
Red/black wire optional (+) input
PIN code
*W/I
W/O
W/I
*W/O
*Reverse Head light Extra sensor
(knock sensor)
warning warning
Press button
once , siren will give 1 chirp and
also in counting time , after your desire time if press
CH-6
button :
Press button
+
output 1~120sec.
If press
button once, siren will give 1 chirp
for programme time when arming/disarming , then
siren will give 1 long chirp to indicate jump to next
item.
Disarming output 1~120sec..
If press
button once, siren will give 1 chirp
CH-7
Press button
+
output 1~120sec. for programme time by press buttons to activate,
then siren will give 1 long chirp to indicate jump to
next item.
Arming output 1~120sec..
20
21
22
Press button
Factory default
once, siren give 2 long chirp
and all features back to factory default.
W/O : means without the feature
W/I : means with the feature
Note:
means factory default setting before delivery.
-26-
System Installation:
1. Thoroughly read and become familiar with the installation instructions before
beginning the installation.
2. Review system contents: (1). A control module. (2).2-way pager transceiver antenna
(3). One 5-button 2-way LCD remote transmitter.
(4).One 3-button or 4-button random code remote transmitter
(5).Dual stage shock sensor (6).High output 6-tone siren (optional )
(7).Status LED indicator
(8).Valet over-ride switch
(9).Harness:
. 20-Pin main harness
. Two 4-pin shock sensor harness
. 6-pin transceiver harness
. 2-Pin dual color LED harness (optional)
. Valet/over-ride switch harness . 6-PIN Central door lock harness
3. Verify with the owner, the mounting location for all visible components, including the
LED and Valet/over-ride switch.
4. Verify with the owner, the optional programme features.
5. Inspect and perform a function test for all vehicle systems before and after the
installation.
6. Always use a Volt / Ohm meter for testing vehicle circuits. Never use a test light.
7. Always look before drilling any holes or mounting self-tapping screws. Be sure fuel
lines and exterior wiring looms are clear as they often close to the chassis and difficult
to see.
8. Protect all wires running from the engine compartment to the interior of the vehicle by
covering with electrical tape and split loom tubing. Be sure to use a grommet when
routing wires through the firewall.
9. Properly fuse any additional accessories such as window module, trunk opener, etc.,
making sure to power them separate from the alarm module. This will ensure the
functionality system in the event of an accessory failure.
Mounting the Control Unit
The control unit only be mounted in the inter of the vehicle. Do not mount the main unit in
the engine compartment. Choose a mounting location that will not be easily accessible
to a thief, and will not interfere with the operation of any vehicle components, such as
foot pedal, steering column, air vents, seat rails, etc.
Do not mounting the control unit until after setting the internal jumpers and performing
a complete operation check of the system. After installation is complete and
performance verified, the control unit can be easily mounted using wire ties through the
mounting tabs on the button of the unit.
Mounting the Shock Sensor
Choose a suitable interior mounting locating for the shock sensor that provides ample
coverage of the vehicle. Keep the sensor away from the vehicle's ECM or other sources
of the electrical interference. Suggested mounting locations include air conditioning
ducts, dashboard braces, or center console supports.
During proper operation, the shock sensor will detect impacts to the vehicle only and
will not usually br triggered by slow rocking movements of the vehicle like those caused
by wind.
-27-
WIRING DIAGRAM
Dual color LED
M
ALAR
2 W AY O L U N I T
R
CONT
Plug-in dual color
LED indicator
R.F Antenna
Antenna
Extend the whole wire, align it
with the intersection of dashboard
and the front window glass.
Keep it away from the metal at
least 5 centimeter to have the
best receiving condition.
6 PIN DOOR
LOCK PORT
Optional blue LED
indicator
1
4
2
5
18PIN
MAIN PORT
3
Engine &
starter
blocking
socket
6
Call switch
Green
Green/black
Green/red
Blue
Blue/black
Blue/red
Optional blue LED
indicator
Plug-in Valet/ over-ride switch
Lock Com
Lock N/C
Lock N/O
Unlock Com
Unlock N/C
Unlock NO
Plug-in dual stage shock sensor
External Ultra sonic &
micro-wave sensor port
+12V DC output
- Ground
1st stage(-) trigger
2nd stage (-) trugger
Red
Black
Blue
Green
Dual-stage/zone
Shock Sensor
-28-
20 PIN MAIN PORT WIRING DIAGRAM
Connect to Chassis
Ground (-)
2
3
4
5
6
7
8
9
ENG / Starter
BLOCKING
(-) Green
Connect to (-)
Negative Door
Pin Switch
Connect to (+)
12Volts Battery
Sources
1
Black(-)
Cutting the vehicle's starter wire
will leave two sides- the ignition
switch side and the starter solenoid
side.
15Amp
Fuse
Connect (+) 12V
Ignition switch
(+) Yellow
Red (+)
Immobilizer-2
(-) Orange/black
Connect to(+)
Positive Door
Pin Switch
(+) Purple
(-) negative pulsed when
disarmed output
+12V
(-) Trunk
output
Trunk release
solenoid
(-) Gray
Optional (+) input (PROG.)
- Reverse warning
- Head light warning
- Extra sensor input
(knock sensor)
Optional relay
(+) Red/black
CH-3
(-) White/black
(-) Yellow/black
Connect to (-) Trunk Pin Switch
(-) Blue
(-) negative pulsed output
for Window close (confort)
CH-4 (PROG)
(-) pulsed output :
- 2nd stage unlock
- Remote latched
CH-5 (PROG)
(-)Gray/black
(+) Siren
Connect to Re
from Siren
(+)Brown
(-) pulsed output for :
-Dome light
-Keep engine run
-Turbo mode
CH-6 (PROG)
(-) Brown/black
(-) Pink
Connect to (-) Hood
Pin Switch
(-) programme time
output 1~120sec.
10Amp Fuse
2 side Parking Lights
(+) /(-) White/red
6A2 diode
Lights(+)or (-) input ,
for parking lights power
sources
CH-7 (PROG)
(+)White
(-) Black/white
-29-
(-) programme time
output 1~120sec.
Central door lock wiring:
1.) For Factory installed central door lock system
MOTOR CONTROL
ORIGINAL
BUILT-IN
CONTROLLER
MOTOR CONTROL
DOWN
DOOR MOTOR LOCK
(Inside of the front door)
UP
MAIN LINE
Central door lock wiring
Green/black
Green
Green/red
Blue/black
Blue
Blue/red
2.) Directly connect to 2 wire Actuator
Central door lock wiring
+ 12V
2 WIRE ACTUATOR
Green/black
Green
Green/red
Blue/black
Blue
Blue/red
LOCK MOTOR
UNLOCK MOTOR
(-)GND
3.) A built-in Central door lock with electric lock switch( like: CHRYSLER.. )
+ 12V
Central door lock wiring
Green/black
Green
Green/red
Blue/black
Blue
Blue/red
DOWN
ELECTRIC
MOTOR
MOTOR LOCK
INSIDE THE
FRONT DOOR
UP
4.) For vacuum type central door lock system ( like : Mercedes Benz , AUDI.. )
Green/black
Green
Green/red
Blue/black
Blue
Blue/red
Note: Door lock active time for 4 secs.
+ 12V
Central door lock wiring
ELECTRIC
MOTOR
DOWN
AIR COMPRESSOR
UP
-30-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement