Avenview HDM-SWITCHPRO-VW4 Specification

Avenview HDM-SWITCHPRO-VW4 Specification
AV Connectivity, Distribution And Beyond...
VIDEO WALLS VIDEO PROCESSORS
VIDEO MATRIX SWITCHES
EXTENDERS SPLITTERS WIRELESS
CABLES & ACCESSORIES
HDBaseT HDMI CAT5/6/7Extender with
POE/LAN/RS-232/ Bi-directional IR
Model #: HBT-C6POE-SET
© 2013 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any
express or implied warranty, relating to its products are is strictly prohibited.
Product Application & Market Sectors
Corporate
House Of Worship
Military
Residential
Education
Industrial
Medical
Aviation
www.avenview.com
TABLE OF CONTENTS
1.
GETTING STARTED...........................................................................................................................1
1.1 Important Safeguards...............................................................................................................1
1.2 Safety Instructions...................................................................................................................1
1.3 Regulatory Notices Federal Communications Commission (FCC)............................ 2
2.Introduction...............................................................................................................................3
2.1Package Contents......................................................................................................................4
2.2 Before Installation....................................................................................................................5
2.3 CABLE SPECIFICATIONS...................................................................................................................5
3.
APPLICATION DIGRAM.....................................................................................................................6
4.Panel Description........................................................................................................................7
4.1 INPUT PANEL (Transmitter, HBT-C6POE-S) Front......................................................................7
4.2 INPUT PANEL (Transmitter HBT-C6POE-S) Rear........................................................................7
4.3 INPUT PANEL (Receiver, HBT-C6POE-R) Front..........................................................................8
4.4 INPUT PANEL (Receiver HBT-C6POE-R) Rear............................................................................8
5.
IR CABLE DEFINITION.......................................................................................................................9
6.
INSTALLATION (HBT-C6POE-SET).................................................................................................10
7.
General Troubleshooting....................................................................................................12
8.Specifications..............................................................................................................................13
www.avenview.com
Page
3
1.GETTING STARTED
SECTION 1: GETTING STARTED
1.1 Important Safeguards
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
What the warranty does not cover
•• Any product, on which the serial number has been defaced, modified or removed.
•• Damage, deterioration or malfunction resulting from:
•• Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to
follow instructions supplied with the product.
•• Repair or attempted repair by anyone not authorized by us.
•• Any damage of the product due to shipment.
•• Removal or installation of the product.
•• Causes external to the product, such as electric power fluctuation or failure.
•• Use of supplies or parts not meeting our specifications.
•• Normal wear and tear.
•• Any other causes which does not relate to a product defect.
•• Removal, installation, and set-up service charges.
1.2 Safety Instructions
The HBT-C6POE-SET HDBaseT HDMI CAT5/6/7 Extender set has been tested for conformance to safety regulations and
requirements, and has been certified for international use. However, like all electronic equipments, the HBT-C6POE-SET should
be used with care. Read the following safety instructions to protect yourself from possible injury and to minimize the risk of
damage to the unit.
! Do not dismantle the housing or modify the module.
! Dismantling the housing or modifying the module may result in electrical shock or burn.
! Refer all servicing to qualified service personnel.
! Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage
or other hazards
! Keep the module away from liquids.
! Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on
to the housing, unplug the module immediately.
! Have the module checked by a qualified service engineer before using it again.
! Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
www.avenview.com
Page
1
1.3 Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.
Warning symbols
Description
ONLY USE THE PROVIDED POWER CABLE OR POWER
ADAPTER SUPPLIED. DO NOT TAMPER WITH THE
ELECTRICAL PARTS. THIS MAY RESULT IN ELECTRICAL
SHOCK OR BURN.
DO NOT TAMPER WITH THE UNIT. DOING SO WILL
VOID THE WARRANTY AND CONTINUED USE OF THE
PRODUCT.
THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.
PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON A
SURFACE, IT SHOULD BE IN A GROUNDED ENVIROMENT.
www.avenview.com
Page
2
2.Introduction
The Avenview HBT-C6POE-SET HDBaseT Extender set CAT5/6/7 with POE, Bi-Directional IR, RS232 and Ethernet has been
designed to extend High Definition video and multi-channel digital audio formats to any HD Monitor.
Video Signals: [email protected] (Ultra HD), 3D, 8/10/12 Deep Color, and Full HD [email protected] Hz/36-bit color depth.
Audio signals: Lossless Multi-channel audio formats (DTS-HD Master Audio, Dolby TrueHD).
Data Signals: Bi-Directional IR signals 30 KHz to 50 KHz over CAT5/6.
The HBT-C6POE-SET includes two (2) units: Sending unit (TX) HBT-C6POE-S and Receiving unit (RX) HBT-C6POE-R with
one (1) UTP output port which allows the user to extend video and audio up to 100m (330ft). The HBT-C6POE-SET also allows
bi- directional IR control of the source connected to the unit from the users IR remote control at the monitor side.
The bonus features with this device it can be powered by the 24V from the TX PoE (Power over the CATx cable to the RX)
also Internet (100Mbps Ethernet service when connected to a Router). These features has been added to this unit to give the
installer and user a complete solution with the new trends in online streaming, network connected devices and new demand in
Smart TV, Ultra HD monitors and content.
-- Input: HDMI with 3D & 4Kx2K, 1080p,HDCP and DVI compliant
-- Video bandwidth: From 300MHz / 9 Gbps
-- Pc resolutions: Up to VGA to WUXGA
-- HD resolutions: Up to 4Kx2K ([email protected] and [email protected])1080p ([email protected])
-- Audio supported: LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio
-- Audio transmission: (32-192kHz sample rate)
-- Supports: CEC bypass
-- Distance: Up to 100 meters through CAT6e/6a/7 cables
-- Ethernet transmission: Rate up to 100Mbps
-- Uncompressed video: 1080p, 60 Hz, 36-bit
-- Service: USB for Manufacturer USE ONLY
-- 3D support: Follow by Display / TV’s EDID
-- 5Play™ convergence: HDMI, LAN, PoE & Bi Directional Control (IR & RS-232)
NOTE:
-- The PoE function is designed for powering compatible Receiver units only.
-- The non-PoE Receivers has to be powered with a power supply.
-- Receivers (Rx) from different manufactures would not be compatible.
-- Displaying HDMI 4Kx2K resolution would require the standard 4Kx2K HDMI cable and display for accurate results.
www.avenview.com
Page
3
2.1Package Contents
Before you start the installation of the converter, please check the package contents.
HBT-C6POE-SET Includes
1
HBT-C6POE-S (TX)
HBT-C6POE-R (RX)
Power Adapter (24V/1.25A DC)
X1
IR Extender
X1
IR Blaster
X1
User’s Manual
X1
2
www.avenview.com
Page
4
2.2 Before Installation
•• Put the product in an even and stable location. If the product falls down or drops, it may cause an injury or malfunction.
•• Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high humidity.
•• Use the DC power adapter with correct specifications. If inappropriate power supply is used then it may cause a fire.
•• Do not twist or pull by force ends of the optical cable. It can cause malfunction.
2.3 CABLE SPECIFICATIONS
CABLE TYPE
CAT5e/6/7
RANGE
100 m
VIDEO DATA
RATE
<=5.3 Gbps
(HD Video)
70m
>5.3 Gbps
(Ultra HD Video)
www.avenview.com
SUPPORTED VIDEO
Up to 1080p, 60Hz, 36bits, 3D ( Data
rates lower than 5.3 Gbps or below 225
MHz TMDS clock).
4K2K, 30Hz
video formats
Page
5
3.
APPLICATION DIGRAM
www.avenview.com
Page
6
4.Panel Description
4.1 INPUT PANEL (Transmitter, HBT-C6POE-S) Front
1
3
2
1. HDMI IN: Connect
2. LAN Connect to a router for LAN sharing. This allows network/internet
HDMI source Max 35ft
access) to be shared over the CATx to the RX.
via HDMI Cable Blu-ray
player or Digital player Warning: DO NOT connect the LAN connection to the CAT5e/6/7 output,
this may trigger a power shut down and may damage the device.
3. RS-232 IN: Connect to a device that has the ability to send control commands ( PC or laptop via D-Sub
9-pin male cable)
4.2 INPUT PANEL (Transmitter HBT-C6POE-S) Rear
5
4
6
7
8
9
4. DC 24V: Connect the 24 V DC power supply included. Secure screw connector.
5. POWER LED: This blue LED will illuminate when the
device is connected to a power supply.
6. IR 1 Blaster: Plug the IR Blaster cable for IR signal
being transmitted. Place IR Blaster within direct site
of the device being controlled.
7. IR 2 Extender: Plug the IR Extender cable for IR signal
being received. Place IR Extender within direct line of
site with the IR Remote.
8. LINK LED: Illuminate when both the input and
9. CAT5e/6/7 OUT: Connect CAT5e/6/7 cable to transoutput signals are in sync. The LED will blink intermit all data signals extend the signal to the Rx unit.
mittently to indicate no signal is being received from
the display and irregularly to indicate that an error
has occurred.
www.avenview.com
Page
7
4.3 INPUT PANEL (Receiver, HBT-C6POE-R) Front
10
11
12
10. HDMI OUT: Connect
11. LAN OUT: Connect to a LAN equipped device (such as a smart
to HDMI display Max
TV or games console) to share the network/internet access.
35ft via HDMI Cable or
Warning: DO NOT connect the LAN connection to the CAT5e/6/7 output,
cascade with another
this may trigger a power shut down and may damage the device.
Avenview type Transmitter
12. RS-232 OUT: Connect to a device that has the ability to Receive control commands via RS232 only with
compatible Transmitters.
4.4 INPUT PANEL (Receiver HBT-C6POE-R) Rear
13
14
15
16
13. IR 2 Blaster: Plug the IR Blaster cable for IR signal being 14. IR 1 Extender: Plug the IR Extender cable for IR sigtransmitted. Place IR Blaster within direct site of the
nal being received. Place IR Extender within direct
device being controlled.
line of site with the IR Remote.
15. LINK LED: Illuminate when both the input and output 16. CAT5e/6/7 IN: Connect CAT5e/6/7 cable to transsignals are in sync. The LED will blink intermittently to
mit all data signals extend the signal from the TX
indicate no signal is being received from the display and
unit.
irregularly to indicate that an error has occurred.
www.avenview.com
Page
8
5.
IR CABLE DEFINITION
Power 5V
IR Blaster Signal
NC
IR Signal
Power V
Grounding
IR Sockets
IR BLASTER: plug in the IR blaster to the HBT-C6POE-R to emit all IR command signals received from the IR Extender plugged
into the TX. IR1 Blaster on TX receives IR from IR1 Extender on RX. IR2 Blaster on RX receives IR from IR2 Extender on TX.
to control the devices corresponding to the IR signals. Example: Set Top Box or DVD player (The Source).
IR EXTENDER: plug in the IR Extender into the (RX) Receiver (Monitor Side) to receive all IR command signals from the IR
remote controls of the corresponding source.
Example: Set Top Box or DVD player (IR Remote Control).
NOTE: Incorrect placement of IR Blaster and IR Extender into the extender may result in the failure of the IR
extenders.
Please check carefully before plugging in the IR extender to the respective IR sockets.
It is clearly marked and IR 1: IR EXTENDER /IR 2: IR BLASTER
WARRANTY WILL NOT COVER THE DAMAGE.
www.avenview.com
Page
9
6.
INSTALLATION (HBT-C6POE-SET)
To setup Avenview HBT-C6POE-SET please follow these steps for connecting to a device:
-- Turn off all devices including monitors / TV
-- .Connect to a HDMI source (such as a Blu-Ray Disc player) to the Transmitter HBT-C6POE-S/SP4/8 or Matrix 4x4/8x8
-- Connect HBT-C6POE-R 100m or HBT-C6POE-RL 60m with a CAT5/6/7 cable with shielded ends, then connect to
display with HDMI cable.
-- Plug in Power for the Tx.
-- Plug in the IR BLASTER: into IR BLASTER in this case and the blinker on the IR eye (Source)
-- Plug in the IR Extender to IR EXTENDER in this case to receive IR Signals from Remote
-- Power on the HDMI display
-- Power on HDMI Sources.
NOTE:The QUALITY and TRANSMISSION of the video signals depends on the characteristics and quality of the
UTP cables. Higher resolutions and longer transmission distances require low skew cables (<25ns/100m) for
best performance.
Unshielded CAT6 with metal RJ-45 connectors is recommended.
www.avenview.com
Page
10
HBTC6POE-S
HDM-SWITCHPRO-VW4
PIN
Assignment
1
NC
2
TxD
3
RxD
4
NC
5
GND
6
NC
7
NC
8
NC
9
NC
Remote
RemoteController(PC)
Controller(PC)
è
ç
PIN
1
2
3
4
5
6
7
8
9
www.avenview.com
De finition
NC
RxD
TxD
NC
GND
NC
NC
NC
NC
Page
11
7.
General Troubleshooting
Problem
Possible Solution
1. Check if connection to the source and the display are correct.
2. Ensure that display device supports 480p, 720p and 1080p [email protected]
resolution
NO IMAGE
3. Terminated to 568B standard with Shielded Ends Recommended
4. High Quality CAT5/6/7 Cable helps signal transmission
5. Please use the supplied power supply-DC 24V 1.25A
6. Check LED Link light see (Section 4 Panel Description)
7. Check LED Sync light see (Section 4 Panel Description)
8. HDBaseT and HDMI 1.3 standards support CLOCK STRETCHING for
i2c buss protocol
Set-Top Box No Picture
9. Example set top boxes like Scientific Atlantic results no picture. This can
be resolved by swapping out the box for a newer version that supports
HDMI 1.3 not HDMI 1.2
10.Ensure the UTP cable is run within the wall away from EMI and High
Voltage power Lines.
NO Infrared
Communication
11.Please check manual of device to ensure proper placement of IR Blaster
on IR EYE.
12.Some LED /Plasma TV have EMI interference with the IR Extender, please
place the IR Rx 3-6” away from Screen
Recommended TEST
End-to-End Testing
13.HDBaseT system, a final end-to-end test of all the A/V components should
take place. These tests include checking the HDMI stream at the far end
(sink end), the clock rate, frame compare, video pattern, audio, EDID and
HDCP with Quantum 780 (recommended)
Passive Monitoring:
14.Passive monitoring enables an integrator to view the HDCP transactions,
EDID exchange, as well as the connection events between the actual
devices in the network.
NOTE
Addional info on Guidelines to Test & Troubleshoot HDBaseT Systems
Can be retreived from our website under the category Downloads for this product HBT-C6POE-SET
www.avenview.com
Page
12
8.Specifications
Item
UNITS
UNIT DESCRIPTION
Description
HBT-C6POE-S
HBT-C6POE-R
HDBaseT HDMI Transmitter
HDBaseT HDMI Receiver
HDCP
YES
ETHERNET SPEED
100Mbps
VIDEO BANDWIDTH
SUPPORTED RESOLUTIONS
Single-link 300MHz [9Gbps]
[email protected]/60, [email protected], 3D [email protected] Up to Ultra HD
([email protected]/25/30Hz)
CEC SUPPORT
CAT5/6/7 CABLE
AUDIO SUPPORT
ALLOWS CEC BYPASS
4K2K: ([email protected]) ~ 70meter (229feet) (CAT6e)
FULL HD: (1080p) ~ 100meter (330feet) (CAT6e/6A)
LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio
HDMI IN CABLE M/M
15m/[email protected] or 6m/[email protected]
HDMI OUT CABLE M/M
15m/[email protected] or 10m/[email protected]
ESD PROTECTION
Human body model — ±8kV (air-gap discharge)
& ±4kV (contact discharge)
1x 3.5mm IR Extender
INPUT
1x CAT5e/6/7
1x RS-232 1x LAN port
1x 3.5mm IR Extender
1x HDMI
OUTPUT
1x 3.5mm IR Blaster
1x CAT5e/6/7
1x RS-232 1x LAN port
1x 3.5mm IR Blaster
1x HDMI
HDMI CONNECTOR
Type A (19 pin female)
LED
YELLOW/BLUE LED
IR FREQUENCY
DIMENSIONS (L X W X H)
WEIGHT
POWER SUPPLY
POWER CONSUMPTION
30~50kHz
4” x 4.4” x 1”
4” x 4.4” x 1”
102 mm (L)×113 mm (W)×25 mm
(H)
102 mm (L)×113 mm (W)×25 mm
(H)
252g /0.5lbs
252g /0.5lbs
24V / 1.25A DC
(US/EU standards, CE/FCC/UL certified)
POE (Powered from Transmitter)
13 Watt (max)
Environmental
Operating Temperature
Storage Temperature
Relative Humidity
32˚ ~ 104˚F (0˚ to 40˚C)
-4˚ ~ 140˚F (-20˚ ~ 60˚C)
20~90% RH (no condensation)
www.avenview.com
Page
13
Notes
www.avenview.com
Page
14
Notes
www.avenview.com
Page
15
Avenview Warranty Certificate
AVENVIEW CORP. (“Avenview”) warrants Avenview-branded product(s) contained in the original packaging against defects in materials and workmanship when used
normally in accordance with Avenview's enclosed manual guidelines for a period of THREE (3) YEARS from the date of original retail purchase - Warranty Period. Avenview’s
published guidelines include but are not limited to information contained in technical specifications, user manuals and service communications.
LABOR: During the Warranty Period of THREE (3) YEARS, Avenview will repair or replace the product(s) at no cost using new or used parts equivalent to novel performance
and reliability if the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Labor applicable to product(s) after Warranty Period. For labor costs,
please contact [email protected]
PARTS: During the Warranty Period of of THREE (3) YEARS, Avenview will supply new or rebuilt replacements in exchange for defective parts of the product(s) at no cost if
the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Parts applicable to product(s) after Warranty Period. For part(s) costs, please contact
[email protected]
To obtain Warranty: (a) proof of purchase in the form of a bill of sale or receipted invoice reflecting that the registered product(s) is within warranty period must be presented
to obtain warranty service; (b) product(s) must be registered at time of purchase. Failure to do so will result in applicable parts and labor charges. Returning product(s) must
be shipped in Avenview’s original packaging or in packaging pertaining equal degree of protection to Avenview’s. Both Avenview and purchaser are responsible for freight
charges and brokerages when shipping the product(s) to the receiver.
NOT COVERED BY THIS WARRANTY
This warranty does not apply to any non-Avenview branded product(s); non-registered Avenview product(s). This warranty does not apply: (a) to cosmetic damage, including
but not limited to scratches, dents and broken cords; (b) to damage caused by use with another product; (c) to damage caused by accident, abuse, misuse, liquid contact, fire,
earthquake or other external cause; (d) to damage caused by operating the Avenview product(s) outside Avenview’s manuals or guidelines; (e) to damage caused by service
performed by anyone who is not a representative of Avenview or an Avenview authorized personnel; (f) to defects caused by normal wear and tear or otherwise due to the
normal aging of the Avenview product(s), or (g) if any serial number has been removed or defaced from the Avenview product(s).
AVENVIEW IS NOT LIABLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR
CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR
ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS;
LOSS OF OPPORTUNITY; LOSS OF GOODWILL; LOSS OF REPUTATION; LOSS OF, DAMAGE TO, COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIRECT
OR CONSEQUENTIAL LOSS OR DAMAGE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
Some states do not allow the inclusion or limitation of incidental or consequential damages, or allow limitations on duration implements of the Warranty Period; therefore the above limitations or
exclusions may not be applicable to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
275 Woodward Avenue, Kenmore, NY 14217
1.866.508.0269
www.avenview.com
AV Connectivity, Distribution And Beyond...
TECHNICAL SUPPORT
USA Head Office
Avenview Corp.
275 Woodward Avenue
Kenmore, NY 14217
Phone: 1.716.218.4100
Fax: 1.866.387.8764
Email: [email protected]
Canada Sales
Avenview
151 Esna Park Drive, Units 11 & 12
Markham, ON, L3R 3B1
Phone: 1.905.907.0525
Fax: 1.866.387.8764
Email: [email protected]
Avenview Europe
Avenview Europe
Demkaweg 11
3555 HW Utrecht
Netherlands
Phone: +31(0)85.2100.613
Email: [email protected]
Avenview Hong Kong
Unit 8, 6/F., Kwai Cheong Centre,
50 Kwai Cheong Road,
Kwai Chung, N.T.
Hong Kong
Phone: 852.3575.9585
Email: [email protected]
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of
Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this
documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages
in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability, function or design.
With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties regarding such products, including but
not limited to, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement