646 | User manual | Paradox Esprit 748+ security control panel Reference and Installation Manual

748+ 24-Zone Control Panel
Software Version 3.20
Reference and Installation Manual
Table of Contents
Introduction...................................................................... 1
About This Manual................................................................
Features ...............................................................................
Specifications .......................................................................
Accessories & Keypads........................................................
About Paradox......................................................................
1
1
1
2
2
INSTALLATION ................................................................ 3
Location & Mounting............................................................. 3
Earth Ground ........................................................................ 3
Power ................................................................................... 3
AC Power .................................................................................... 3
Back-up Battery .......................................................................... 3
Auxiliary Power Terminals .......................................................... 3
Battery Test ................................................................................ 4
Keypad Function Test ................................................................. 4
Telephone Line Connection..................................................
Bell/Siren Output. .................................................................
Programmable Outputs (PGM).............................................
Keypad & Keyswitch Connections........................................
Keypad Zone Connections ...................................................
Single Zone Input Terminal Connections .............................
4
4
5
5
5
7
N.C. Contacts, Without EOL Resistor ......................................... 7
N.O. and N.C. Contacts, With EOL Resistor (UL) ...................... 7
N.C. Contacts, Without EOL Resistor, With Tamper Recognition8
N.C. Contacts, With EOL Resistor, With Tamper and Wire Fault
Recognition (UL) ......................................................................... 8
Advanced Technology Zone (ATZ) Connections.................. 8
N.C. Contacts, Without EOL Resistor ......................................... 9
N.C. Contacts, Without EOL Resistor, With Tamper Recognition9
N.C. Contacts, With EOL Resistor, With Tamper & Wire Fault Recognition (UL) ............................................................................... 9
Fire Circuit .......................................................................... 10
Standard Installation ................................................................. 10
UL/cUL Installation .................................................................... 10
Serial Output Connector ..................................................... 10
ACCESS CODES ............................................................ 11
Installer Code .....................................................................
Master & User Codes .........................................................
User / Access Code Length................................................
Duress ................................................................................
Installer Lock ......................................................................
11
11
11
11
11
PROGRAMMING METHODS.......................................... 12
Espload Software ............................................................... 12
Keypad ............................................................................... 12
Hexa Programming ................................................................... 12
Hexa Streamlined Section Programming .................................. 13
Decimal Programming .............................................................. 13
Feature Select Programming .................................................... 14
Key Access Programming ........................................................ 14
PANEL SETTINGS FOR ESPLOAD............................... 15
Panel Answer Options ........................................................
Panel Identifier ...................................................................
PC Password......................................................................
Computer Telephone Number ............................................
Call Espload .......................................................................
Answer Espload..................................................................
Cancel Communication ......................................................
15
15
16
16
16
16
16
Call Back............................................................................. 16
Automatic Event Buffer Transmission................................. 17
Event Reporting ............................................................. 18
Reporting Options ............................................................... 19
Reporting Disabled ................................................................... 19
Regular Reporting .................................................................... 19
Split Reporting .......................................................................... 19
Double Reporting ..................................................................... 19
Monitoring Station Telephone Number 1 ............................
Monitoring Station Telephone Number 2 ............................
System Account Codes.......................................................
Communicator Formats ......................................................
20
20
21
21
Ademco Contact ID (all codes) ................................................ 21
Ademco Contact ID (programmable codes) ............................. 22
Ademco Express ...................................................................... 22
DTMF - no handshake ............................................................. 22
Standard Pulse Formats .......................................................... 22
Reporting Event Codes....................................................... 22
Arming Codes .......................................................................... 23
Disarming Codes ...................................................................... 23
Alarm Codes ............................................................................ 23
Restore Codes ......................................................................... 23
Shutdown Codes ...................................................................... 23
Tamper/Trouble Codes ............................................................ 23
Trouble/Restore Codes ............................................................ 23
Special Codes .......................................................................... 24
Auto Test Report.................................................................
Manual Test Report ............................................................
Power Failure Report Delay................................................
Recent Close Delay ............................................................
Report Zone Restore Options .............................................
Report Code Disarming Options .........................................
24
24
24
24
25
25
ZONE DEFINITIONS ....................................................... 26
Zone Speed ........................................................................ 27
Advanced Technology Zoning (ATZ) .................................. 27
Intellizones .......................................................................... 27
Intellizone Time Delay .............................................................. 27
Silent Zones ........................................................................ 27
24 Hour & Fire Zones.......................................................... 27
Zone 15 (Enable/Disable) ........................................................ 28
Instant Zones ......................................................................
Follow Zones.......................................................................
Entry Delay 1 ......................................................................
Entry Delay 2 ......................................................................
28
28
28
28
Entry Time Delay 2 ................................................................... 29
Partitioning .......................................................................... 29
System A/Stay Zones ............................................................... 29
System B Zones ....................................................................... 29
Bypass Enabled Zones ....................................................... 29
Auto Zone Shutdown ................................................................ 29
EOL Zones (Enabled/Disabled) .......................................... 29
Keypad Zone 1 Supervision................................................ 30
Keypad Zone 2 Supervision................................................ 30
ARM/DISARM & ALARM OPTIONS............................... 31
Timed Auto Arming ............................................................. 32
Auto Arm Time ......................................................................... 32
Auto Arming Options ................................................................ 32
No Movement Auto Arming................................................. 32
No Movement Auto Arm Time .................................................. 32
Esprit 748 +
One-Key Regular Arming....................................................
One-Key Stay/System A Arming.........................................
Arming using a keyswitch ...................................................
Bell Squawk ........................................................................
Exit Delay............................................................................
Beep on Exit Delay .............................................................
Alarm Transmission Delay ..................................................
Silent Zones & Silent Panics Option ...................................
Bell Cut-Off Time ................................................................
Code Priority .......................................................................
32
33
33
33
33
33
34
34
34
34
PGM (PROGRAMMABLE OUTPUT).............................. 35
PGM Types ......................................................................... 35
PGM Timer Setting ............................................................. 35
PGM Options ...................................................................... 36
OTHER OPTIONS........................................................... 37
Telephone Line Monitoring (TLM).......................................
Dialing Options ...................................................................
Dialing Pulse Rates.............................................................
Keypad Panic Options ........................................................
Panel Time..........................................................................
Time Correction ..................................................................
Tamper/Wire Fault Recognition Options.............................
Tamper Bypass Options .....................................................
Installer Test Mode .............................................................
Exclude Power Failure From Trouble Display.....................
Audible Trouble Warning ....................................................
Power Down Reset .............................................................
37
37
37
37
38
38
38
39
39
39
39
39
USER/KEYPAD FUNCTIONS......................................... 40
Programming Master & User Codes ................................... 40
Regular Arming ................................................................... 40
One-Key Regular Arming .......................................................... 40
Away Arming....................................................................... 40
Stay Arming ........................................................................ 41
One-Key Stay Arming ............................................................... 41
One-Key Double Stay Arming ................................................... 41
Fast Exit .................................................................................... 41
Arming/Disarming Partitions ............................................... 41
One-Key System A Arming ....................................................... 42
System Disarming...............................................................
Alarm Memory.....................................................................
Keyswitch or Pushbutton Arming/Disarming.......................
Manual Zone Bypassing .....................................................
Bypass Recall .....................................................................
Keypad Chime Zones .........................................................
Trouble Display Monitoring .................................................
42
42
42
42
43
43
43
No Battery/Low Battery - Key [1] .............................................. 43
Power Failure - Key [2] ............................................................. 43
Bell Disconnected - Key [4] ....................................................... 43
Maximum Bell current - Key [5] ................................................. 43
Maximum Auxiliary Current - Key [6] ........................................ 44
Communicator Report Failure - Key [7] .................................... 44
Timer Loss - Key [8] .................................................................. 44
Tamper/Zone Wiring Failure - Key [9] ....................................... 44
Telephone Line Monitoring - Key [10] ....................................... 44
Fire Trouble - Key [11] .............................................................. 44
Key Access Programming................................................... 44
Warnings ........................................................................ 45
Reference & Installation Manual
Part 1: Introduction
1.1
About This Manual
This manual provides all the information you will need to understand panel operation, features and functions. If you are familiar
with other security control panels, we recommend that you read this manual at least once to familiarize yourself with panel
features and programming. Please refer to the index for a complete list of this manual's contents.
The following terminology is used throughout this manual:
[ ] = indicates a key on the keypad
[ ] = indicates a key on the keypad must be pressed
= indicates a warning or important note
italic = indicates data that must be entered, reference to a section in the manual, or an example
“SMALL CAPS” = indicates terminals or LEDs that are located on the control panel, keypad, etc.
1.2
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1.3
Improved Lightning Protection
New and Innovative Dialer Circuit
748+ : 24 zones (12 on-board inputs with ATZ = 24 zones including 2 keypad zones)
Powerful 16-bit RISC processor with built in analog to digital converters
User-friendly programming
"False Alarm Prevention" features such as: Intellizones, Auto Zone Shutdown, Beep on Exit Delay, Programmable
Delay Before Alarm Transmission, and Recent Closing Report
2 Flexible Partitions
High-Speed Communication Formats
256 Event Buffer with time and date stamp
2 fully programmable outputs (PGMs) Upload & Download capability with Espload Software
Alarm Relay
48 User Codes + 1 Master Code + 1 Installer Code
Telephone Line Supervision
3 keypad activated panic alarms
Regular Arming, "Stay" Arming, "Double Stay" Arming, Force "Away" Arming, "One- Key” Regular Arm, "One-Key" Stay Arm,
"One-Key" Exit & Re-arm, "Auto Arming", Key Switch
Specifications
Battery Charger:
Aux. Power:
Bell Out:
AC input:
PGM outputs:
Serial Data Output:
360mA with dynamic Battery test.
Two auxiliary outputs rated at 1A each. Fuseless electronic shutdown at 1.1A, automatic restore
1A, Fuseless electronic shutdown at 3A, automatic restore
16.5 VAC, 40VA min. (recommended: 75VA), 50 - 60Hz
N.C. or N.O to ground, 50mA Max.
(1200, 1, N) for use with accessory modules (not UL systems).
Esprit 748+
1
1.4
Accessories & Keypads
If you would like to obtain more information on the following keypads, security system accessories or other security products,
please contact your local Paradox distributor or come and visit us at our web site http://www.paradox.ca
•
•
•
•
1.5
Esprit 636/646 LED Keypads
Esprit 642 LCD Keypads
A wide range of analog and digital Motion Detectors
Glass Break Detector
About Paradox
Paradox Security Systems strives to design and manufacture the best security products money could buy. Our products are of
the highest quality standards and most importantly meet the needs and expectations of our customers.
By refusing to settle for the limitations of existing technology, Paradox makes it clear, we are not interested in mirroring the
products already on the market. Breaking down barriers to better technology is what innovation is all about.
The guiding principle behind Paradox research and development has always been to create security products that make sense.
Whether the situation calls for a full range of "intelligent" and easy to use control panels, efficient peripheral security devices, or
"false alarm free" motion or breaking glass detectors. We are putting all our resources into developing products that reflect our
twin philosophies of innovation and user-friendliness. Now we invite you to reap the benefits.
2 Reference & Installation Manual
Part 2: INSTALLATION
2.1
Location & Mounting
Remove the printed circuit board, mounting hardware and keypad from the packaging inside the panel box. The circuit board
should not be mounted into the back of the cabinet, until all cables are pulled into the cabinet and prepared for connection. Before
mounting the cabinet, push the five white nylon-mounting studs into the back of the cabinet. Select an installation site that is not
easily accessible to intruders. Leave at least 2" around the panel box to permit adequate ventilation and heat dissipation. The
installation site should be dry and close to an AC source, ground connection and telephone line connection.
WARNING: THIS EQUIPMENT MUST BE INSTALLED AND MAINTAINED BY QUALIFIED SERVICE PERSONNEL
ONLY.
2.2
Earth Ground
Connect the zone and dialer ground terminals from the control panel to the metallic
enclosure and cold water pipe or grounding rod as per local electrical codes. For
UL and cUL warnings, refer to the Warnings section.
Figure 1
For maximum lightning protection use separate earth grounds for
the zone and dialer grounds (see Figure 1)
2.3
Power
2.3.1
AC Power
Figure 2
Use a 16.5Vac (50-60Hz) transformer with a MINIMUM 40VA rating to provide sufficient AC
power (aux outputs = 500mA each); RECOMMENDED 75VA rating to provide maximum
power output (aux outputs = 1A each). Do not use any switch-controlled outlets to power the
transformer. For UL and cUL warnings, refer to the Warnings section.
Do not connect the transformer or the back-up battery until all wiring is
completed
2.3.2
Back-up Battery
Figure 3
We recommend connecting a back-up battery to power the control panel, in case of power loss. Use
a 12Vdc 4Ah / 7Ah rechargeable acid/lead or gel cell battery. Connect the back-up battery after
applying the AC power. When installing the battery, verify proper polarity, as reversed connections
will blow the battery fuse. Connect the "red" battery lead to the positive battery terminal, and the
"black" battery lead to the negative battery terminal of the control panel. Use the Battery Charge
Current Jumper on the PCB to determine the charging current of the backup battery. With the jumper
ON, the charging current will be set at 350mA. With the jumper OFF, the charging current will be set
at 700mA.
2.3.3
Auxiliary Power Terminals
The auxiliary power supply terminals can be used to power motion detectors, keypads, and other modules or accessories in the
security system. A fuseless sircuit protects the auxiliary output against current overload and automatically shuts down if the
current exceeds 1.1A. If this occurs, the MAximum Auxiliary Current failure will appear in the keypads’ Trouble Display (see page
43). Therefore, the combined current consumption of devices connected to each of the auxiliary power supply should not exceed
700mA. If the auxiliary output is overloaded and is shutdown, you must disconnect all loads from the output for at least 10
seconds before reconnecting any load back to the auxiliary output. The maximum available current of the 748+ is 1.7A. So if the
Esprit 748+
3
battery charging is set at 700 mA, then only 1A is left for the auxiliary output. If the battery charging is set at 350mA, then 1.35A
is available for the AUX output, but with a maximum of 700mA per output.
Table 1: Current Consumption Table
Modules
Motion Detectors (see detector instructions for details)
636/646* LED Keypads
642* LCD Keypads
708 Ultra Stand-Alone Digital Dialer
MG-RCV3 Wireless Expansion Module
2.3.4
Current Consumption
Typical
10 to 50mA
15mA
40mA
50mA
50mA
Maximum
30mA
55mA
50mA
50mA
Battery Test
The control panel conducts a dynamic battery test under load every 60 seconds. If the battery is disconnected, or its
capacity is too low, the [1] key in the trouble display mode will be on. Key [1] also comes "on" if the battery voltage
drops to 10.5 volts or less when the control panel is running on the back-up battery (no AC). At 8.5 volts, the panel
shuts down and all outputs close.
2.3.5
Keypad Function Test
We recommend conducting a "power-up" test on keypads installed far from the control panel. To do so temporarily
connect the keypads near the control panel and connect the transformer. After 10 seconds, begin entering random
commands on the keypad and verify that the keypad "beeps" in response to these commands. Then open a zone to
ensure that the keypad and the control panel are responding to these signals. If the keypad does not respond and
indicator lights do not illuminate, verify that approximately 16Vac is present at the "AC" terminals. If AC is present,
check the keypad wiring and verify there isn't a short between the "black" and "red" keypad wires. If the keypad does
not respond, please contact your local Paradox Distributor.
2.4
Telephone Line Connection
Figure 4
Connect the incoming telephone company wires into the tip and ring connections
of the control panel. Then run the wires from T-1 and R-1 to the telephone system
as shown in Figure 4.
2.5
Bell/Siren Output.
The BELL+ and BELL- terminals power bells and/or other warning devices requiring a steady
voltage output during an alarm. The bell output supplies 12Vdc upon alarm and can support
two 20-watt or two 30-watt sirens. The bell output is microprocessor-controlled and will
automatically shut down if the current exceeds 3A. If the load on the BELL terminals returns to
normal (≤3A), the control panel will re-instate power to the BELL terminals. When connecting
sirens (speakers with built-in siren drivers) please verify correct polarity. Connect the positive
lead to the BELL+ terminal and the negative lead to the BELL- terminal of the control panel as
shown in Figure 5. The Alarm Relay (optional), which is rated at 5A, can also be used to power
bells and/or other warning devices requiring a steady voltage output during an alarm (see
Figure 5). The Alarm Relay is activated (toggles to opposite state) whenever the local bell/
siren output is activated.
4 Reference & Installation Manual
Figure 5
If the Bell/Siren output is not being used when connecting a bell or siren to an optional relay output, the [4]
trouble indicator (see section 11.12.3) will always be on. To avoid this, connect a 1KW resistor across the bell
output.
2.6
Programmable Outputs (PGM)
Figure 6
The 748+ control panels includes two fully programmable output (PGM). When a
specific event or condition occurs in the system, a PGM can be used to reset
smoke detectors, activate strobe lights, open/close garage doors and much
more. The PGMs provide a maximum 50mA output. If the current draw on a
PGM output is to exceed 50mA we recommend the use of a relay as show in
Figure 6. The PGMs can be programmed to toggle on and off from more than a
thousand different events. For example, PGM1 can open and close an automatic
garage door by pressing keys [1] and [2] simultaneously on the keypad. For
details on how to program the PGMs, refer to section 9.
2.7
Keypad & Keyswitch Connections
Figure 7
Connect the four keypad connections labeled RED, BLACK, GREEN and YELLOW to the
corresponding colour terminals on the control panel as indicated in Figure 7. Note, on
some keypads you may have to remove the back panel to make the connections.
Connect the keyswitch to the “GRN” and “BLK” terminals of the control panel as shown
in Figure 7. To enable this function please refer to sections 8.5 and 11.8 for more
information on keyswitches.
2.8
Keypad Zone Connections
Each keypad comes with one input terminal, allowing you to connect one detector or door contact directly to the keypad. Once
the keypad zones have been defined you must enable "Keypad Zone Supervision" (see section 7.13 & 7.14) in the control panel.
Figures 8 and 9 demonstrate typical keypad zone input installations.
Example: A door contact located at the entry point of an establishment can be wired directly to the input terminal of the
entry point keypad instead of wiring the door contact all the way to the control panel.
If a keypad has the ATZ (zone doubling) feature, two detection devices can be connected to one input terminal. Each device will
be assigned a zone (see table below) and each will transmit a separate alarm code, therefore, capable of adding one or two
zones to your security system. Regardless of the number of keypads in the system, the control panel supports a maximum of two
keypad zones.
Example 1: A security installation is comprised of five keypads. Of these five keypads only two can have their zone input
terminals enabled (see Figure 9). The other three keypads must have their zone input terminals disabled as described
below.
Example 2: A security installation is comprised of three 636 keypads and two 642 LCD keypads. You can enable the ATZ
(Zone Doubling) feature on one of the 642 keypads, providing you with 2 zones on one keypad input terminal (see Figure
10). The remaining four keypads must have their input terminals disabled as described below.
Note if using two keypad zones, one keypad must be defined as keypad zone 1 while the other must be defined as keypad zone
2. Unless you are using an LCD keypad with the ATZ (zone doubling) feature enabled, in which case the LCD will automatically
define the keypad zones. The control panel will recognize these added zones as shown in the table below.
Disabling 636/646 Keypad Zones:
If the keypad zone input terminal is not being used, disable it by shorting the blue zone wire with the black com wire of the
keypad.
Esprit 748+
5
Disabling 642 Keypad Zones:
If the keypad zone input terminal is not being used, disable it by shorting the ZONE and COM terminals of the keypad with a 1KW
resistor.
Table 2: Keypad Zone Recognition
If using an LED keypad simply set the Zone Select Jumper at the back of the keypad:
Zone Select Jumper "OFF" = Keypad Zone 1
Zone Select Jumper "ON" = Keypad Zone 2
Note:
If the zone select jumper is changed, the control panel will only recognize the change
when the keypad is disconnected and re-connected.
If using an LCD keypad with ATZ disabled, program the keypad definition as follows:
Keypad Programming Mode, option [2] (Keypad Options); Key [3] OFF = Keypad Zone 1
Keypad Programming Mode, option [2] (Keypad Options); Key [3] ON = Keypad Zone 2
The control panel will display open keypad zones as follows:
Kpd Zone 1 = Zone [13]
Kpd Zone 2 = Zone [14]
Note: When the ATZ feature is enabled in the control panel, it will not be able to distinguish
between zone 13 and keypad zone 1 and between zone 14 and keypad zone 2
(see section 2.10)
Once the keypad zones have been defined you must enable "Keypad Zone Supervision" (see section 7.13 & 7.14) in the control
panel. Figures 8 and 9 demonstrate typical keypad zone input installations.
6 Reference & Installation Manual
2.9
Single Zone Input Terminal Connections
The system hardware recognizes the following single zone input terminal connections. For more information on programming the
options mentioned below refer to ZONE DEFINITIONS in section 7 on page 26.
2.9.1
N.C. Contacts, Without EOL Resistor
Figure 11
If your security installation does not require tamper
or wire fault detection, connect the detection
devices and program the control panel as shown
in Figure 11. This setup will communicate an open
or closed zone to the control panel, displaying
open zones on the keypad. Do not use devices
with normally open contacts in this setup, as this
will cause the control panel to remain in alarm.
2.9.2
N.O. and N.C. Contacts, With EOL Resistor (UL)
Figure 12
Figure 13
If your security installation does not require tamper
or wire fault recognition but some detection devices
will use normally open contacts. Connect all
detection devices using a 1KW end of line (EOL)
resistor and program the control panel as shown in
Figures 12 and 13. This setup will communicate an
open or closed zone to the control panel, displaying
open zones on the keypad.
Esprit 748+
7
2.9.3
N.C. Contacts, Without EOL Resistor, With
Tamper Recognition
Figure 14
If your security installation requires tamper
recognition, all detection devices must use normally
closed contacts. Connect the devices and program
the control panel as shown in Figure 14. This setup
will communicate an open or closed zone to the
control panel, displaying open zones on the keypad.
The control panel will also communicate any
detected tampers (cuts) as per Tamper/Wire Fault
Recognition Options (see section 10.7 on page 38).
2.9.4
N.C. Contacts, With EOL Resistor, With
Tamper and Wire Fault Recognition (UL)
Figure 15
If your security installation requires tamper (cut)
and wire fault (short) recognition, all detection
devices must use normally closed contacts.
Connect the devices and program the control panel
as shown in Figure 15. This setup will communicate
an open or closed zone to the control panel,
displaying open zones on the keypad. The control
panel will also communicate any detected tampers
(cuts) and/or wire faults (short) as per Tamper/Wire
Fault Recognition
Options (see section 10.7 on page 38)
2.10
Advanced Technology Zone (ATZ) Connections
Enabling the ATZ feature (see section 7.2 on page 27) allows you install two detection devices per input terminal, therefore,
doubling zone capacity of the control panel. Advanced Technology Zoning is a software-oriented feature, there is no need for
extra modules, simply install the devices as shown in Figures 17 to 19. The control panel will recognize the installed devices as
shown in Figure 16. The extra zones function exactly like any other zone displaying zone status on the keypad and sending
separate alarm codes for each zone. For more information on programming the options mentioned in the following sections refer
to ZONE DEFINITIONS in section 7 on page 26.
Figure 16
When ATZ is enabled, keypad zones are recognized as zones 13 and 14. This means that the control panel will
not be able to distinguish between zone 13 and keypad zone 1 and between zone 14 and keypad zone 2.
8 Reference & Installation Manual
2.10.1
N.C. Contacts, Without EOL Resistor
If your security installation does not require tamper or wire
fault recognition but you are using the ATZ feature,
connect the detection devices and program the control
panel as shown in Figure 17. Do not use devices with
normally open contacts, as this will cause the system to
remain in alarm. This setup will communicate the status of
each device to the control panel (see Figure 16),
displaying open zones on the keypad.
2.10.2
N.C. Contacts, Without EOL Resistor, With
Tamper Recognition
Figure 17
Figure 18
If your security installation requires tamper recognition and
you are using the ATZ feature, connect the detection
devices and program the control panel as shown in Figure
18. Do not use devices with normally open contacts, as this
will cause the zone to remain open. This setup will
communicate the status of each zone to the control panel
(see Figure 16), displaying open zones on the keypad. The
control panel will also communicate any detected tampers
(cuts) on the system as per Tamper/Wire Fault Recognition
Options (see section 10.7).
2.10.3
N.C. Contacts, With EOL Resistor, With Tamper &
Wire Fault Recognition (UL)
Figure 19
If your system requires tamper (cut) and wire fault (short)
recognition, connect two detection devices to one input
terminal with a 1KW end of line (EOL) resistor and program
the control panel as shown in Figure 19. Do not use devices
with normally open contacts, this will cause the zone to
remain open. This setup will communicate the status of each
zone to the control panel (see Figure 16), displaying open
zones on the keypad. Any tampers (cuts) and/or wire fault
(shorts) detected on the system are communicated as per
Tamper/Wire Fault Recognition Options (see section 10.7).
Esprit 748+
9
2.11
Fire Circuit
If your security installation requires the use of smoke detectors, define zone 3 as a "24-hour" fire zone; please
refer to section 7.5.
2.11.1
Standard Installation
Connect the smoke detectors to zone 3 as shown in Figure 20. Note that a fire zone must use a
1KW EOL resistor. If there is a line short or if the smoke detector becomes active, whether the
system is armed or disarmed, the control panel will generate an alarm (see Fire Alarm Output Figure
on page 28). If the line is "open", the control panel will send a "fire loop" trouble report to the
monitoring station and trouble indicator, key [11], will appear in the keypad’s trouble display.
2.11.2
UL/cUL Installation
For UL installations, use a 4-wire, latching, smoke detector (System Sensor - Model 2112/
240). To supervise the power supply, install an "end of line" relay (Model MR3). Connect
the smoke detectors and relay as shown in Figure 21. In the event power is interrupted the
relay will cause a FIRE TROUBLE report to be generated (see section 7.5).
To reset (unlatch) the smoke detectors after an alarm, momentarily interrupt power to the
detectors. To do so, verify that the negative (-) of the smoke detectors is connected to a
PGM. Set the PGM for "Timed N.C." (normally closed), and program the PGM to "open"
when any two keys on the keypad are pressed simultaneously. For more information on
programming the PGM refer to section 9. For UL and cUL warnings, refer to the Warnings
section.
EXAMPLE: To program PGM1 to conduct a smoke detector reset when the [clear] and [enter] keys are pressed at the
same time.
Address 039 = [byp] [2nd]
Address 040 = [5] [10]
Address 042 = [2nd] [6]
Address 056 = [10] [10] [4]
It is recommended to connect all 4-wire smoke detectors using a daisy chain configuration.
2.12
Serial Output Connector
The four pin Serial Output Connector is used to connect additional devices such as the 708DVACS communicator, the Esprint
printing module and the SRI-18 PGM Expander Module to the control panel. For serial output connector specifications refer to
section 1.3.
10 Reference & Installation Manual
Part 3: ACCESS CODES
3.1
Installer Code
Streamline - Section 00 D Hexa Programming - Addresses 000-002
Default: 748+ = 484848
Only the installer code allows you to program all control panel settings, except the Master and User codes. To program any
setting in the control panel you must enter the programming mode by pressing the [ENTER] key followed by the installer code. The
installer code contains six digits and each digit can be any value from 0 to 9. Although the control panel can accept 4-digit codes,
when programming the installer code, always enter six digits. To change the installer code press:
[ENTER] + Installer Code + [10] [10] [10] + First 2 digits + [10] [10] [1] + Next 2 digits + [10] [10] [2] + Final 2 digits + [ENTER]
3.2
Master & User Codes
Default Master Code: 474747
You cannot use the installer code to program the master and user codes. Only the master and user 1 codes can program these
access codes. (See section 11.1)
3.3
User / Access Code Length
Feature Select Programming D Address 088, key [9]
Default: 6-digit Access Codes
When programming user codes an option for either 4-digit or 6-digit access codes can be programmed. When the 4-digit option is
selected, entering a 4-digit code will allow the person access. Using the 6-digit option, entering 6 digits is required to allow
access.
Key [9] "Off": 6-digit Access Codes
Key [9] "On": 4-digit Access Codes
[ENTER] + Installer Code + [10] [8] [8] + [9] On/Off + [ENTER] twice
3.4
Duress
Feature Select Programming D Address 090, key [10]
Default: Duress Disabled
When unwillingly forced to disarm a system, a User can enter the User Code #48 instead of their usual code. This code will
disarm the system and send a silent alert (Duress Code) to the Monitoring Station.
Key [10] "Off": Duress Disabled
Key [10] "On": Duress Enabled
[ENTER] + Installer Code + [10] [9] [10] + [10] On/Off + [ENTER] twice
3.5
Installer Lock
Decimal Programming D Address 058
Default: Address Empty
Program 147 into address 058 to lock all programming. Hence, performing a hardware reset (see section 10.12) will not affect the
current settings. To remove the installer lock, enter any value besides 147.
[ENTER] + Installer Code + [10] [5] [8] + [1] [4] [7] + [ENTER]
Esprit 748+
11
Part 4: PROGRAMMING METHODS
The 748+ Control Panels can be programmed using either the keypad or the Espload Software. We highly recommend
programming the control panels using the Espload Software, as it simplifies the process and reduces the potential of data entry
errors. You can also program the control panels manually by using a keypad.
4.1
Espload Software
With the Espload Software, you can program the 748+ family of control panels remotely via modem or locally using an ADP-1
adapter. The advanced Espload software can execute fast uploads or downloads and provides many powerful features. These
include a comprehensive "monitoring" mode to oversee all panel activity, a "scheduler" to initiate pre-programmed tasks at set
intervals, and a "batch" mode to carry out pre-programmed tasks following a call from the control panel. Using Espload there is no
limit to the number of account files or panel defaults created and you can assign thousands of programming combinations to the
PGM outputs. Espload can also be converted to the language of your choice. Contact your local Paradox Distributor for your FREE
copy of the Espload software.
4.2
Keypad
When programming, use the supplied "Programming Guide" to keep track of which addresses were programmed and how.
Before you begin programming the control panel, we recommend you read sections 5 through 11 of this manual in order to
acquire a good understanding of the control panel and its many features. When programming with the keypad, certain addresses
are programmed using different methods. These methods are described in detail below. Each section in this manual will
reference the appropriate programming method.
4.2.1
Hexa Programming
Addresses 000 to 043 and 300 to 527 are programmed using the Hexa Programming method. In this mode, you can
enter any hexa-digit from 0-F where keys [1] to [9] represent digits 1 to 9 respectively; the other keys represent hexadigits A to F as shown in Figure 22. To program using the Hexa Programming method:
1)Press [ENTER] + Installer Code
2)The [ENTER] key will flash indicating you are in programming mode
3)Enter the desired 3-digit address
4)The keypad will display the 2-digit data currently saved at this address as described in Figure 22
5)Enter 2-digit data; after entering data you do not need to press enter, the software will automatically save the data
into the selected address
6)Return to step 2 to continue programming or press [CLEAR] to exit programming mode
12 Reference & Installation Manual
Figure 22
4.2.2
Hexa Streamlined Section Programming
This is an alternate method to Hexa Programming. The addresses (000-043 and 300-527) programmed in the Hexa
Programming method are grouped into 67 sections where each section contains four addresses (i.e. section 00 = addresses 000003). Using this method allows you to program 8 digits (4 addresses) without having to exit and re-enter addresses. When
entering the final digit, the software will automatically advance to the next section.
Example: If you complete the "Programming Guide" with the desired data, you can program the 68 sections by entering
all digits without pressing [enter] or entering any other addresses. This greatly reduces programming time.
Note: the keypad will not display the current data in the Hexa Streamlined Programming method. To program using the Hexa
Streamlined Section method:
1) Press [ENTER] + Installer code + [7]
2) The [ENTER] and [2ND] keys will flash to indicate you are in streamlined programming mode
3) Enter 2-digit section (00-67)
4) The [ENTER] key will remain on and the [2nd] key will turn off
5) Enter 8-digit data to program the section
6) The keypad will "beep" to indicate that the section has been programmed, data is saved and the software has advanced to the
next section
7) Return to step 4 to continue programming or press [CLEAR] to exit programming mode
4.2.3
Decimal Programming
Addresses 044 to 061 are programmed using the Decimal Programming method. Values entered must contain three digits from
000 to 255 (where the [10] key = 0). To program using the Decimal Programming method:
1) Press [ENTER] + Installer Code
2) The [ENTER] key will flash to indicate you are in programming mode
3) Enter 3-digit address (044-061)
4) The keypad will now display the current 3-digit data currently saved at this address as described in Figure 22
Esprit 748+
13
5) Enter 3-digit data (decimal) value; after entering data you do not need to press [ENTER], the software will automatically save the
data into the selected address
6) Return to step 2 to continue programming or press [CLEAR] to exit programming mode
4.2.4
Feature Select Programming
Addresses 062 to 126 are programmed using the Feature Select Programming method. In this method, every key in
each address on the keypad represents an option or feature. Pressing a key will display it on the keypad and pressing
it again will extinguish the key. The On/Off status of each key determines the selected feature. To program using the
Feature Select Programming method:
1) Press [ENTER] + Installer Code
2) The [ENTER] key will flash to indicate you are in programming mode
3) Enter 3-digit address (062-126)
4) After entering the address, the keypad will display the feature selection status. The On/Off status of the keys
determines the selected features as described in the "Programming Guide" and in the appropriate sections of this
manual. Turn the keys On/Off by pressing the appropriate key until the desired options are set. Then press the [ENTER]
key to accept, there will be a confirmation "beep" indicating the options have been accepted. The [enter] key will flash
to indicate that the software is awaiting the next address entry
5) Return to step 3 to continue programming or press [CLEAR] to exit programming mode
4.2.5
Key Access Programming
This method allows for quick programming of features without entering addresses or section numbers. The following
features are programmed using the installer code as well as the master and user 1 codes.
•
•
•
•
•
•
•
Installer Test Mode: see section 10.9
Auto Arm Time: see section 8.1.1
Answer Espload: see section 5.6
Call Espload: see section 5.5
Cancel Communication: see section 5.7
Manual Test Report: see section 6.8
Panel Time: see section 10.5
14 Reference & Installation Manual
Part 5: PANEL SETTINGS FOR ESPLOAD
5.1
Panel Answer Options
Streamline - Section 00 D Hexa Programming - Address 003
Default: Answering Machine Override Disabled & Maximum 8 rings
The following two options will define how the control panels answer an incoming call from a computer using the Espload software.
In order for the Espload software to remotely communicate with the control panel, call the installation site twice using
the Espload Software. To do so, program the first digit in address 003 with any value from 1-F (see table 2 below), this
value represents the delay period the control panel will wait between the first and second call. Using the Espload
software, call the installation site and on the second ring press [ENTER] on the keyboard to hang-up. After hanging up,
the Espload software will immediately call the installation site back. If the installation site is called back within the
programmed delay period, the control panel will override the answering machine or service by picking-up on the first
ring. To disable this option program [2nd] or [1] as the first digit in address 003.
Example: A security installation is using an answering machine set to answer after 3 rings, the first digit at address 003
has been programmed with [5] (40 sec.) and the second digit has been programmed with 8. When you call the installation
site with the Espload software the first time, wait two rings and press [enter] on the keyboard. The Espload software will
immediately call the installation site back. If the second call is made within 40 seconds, the panel will pick up the line on
the first ring. If it takes more than 40 seconds, the panel will not answer on the first ring and the answering machine will
answer after three rings.
Table 3: Answering Machine Override Options
[2nd] or [1] = Answering Machine Override disabled
[2] = 16 seconds
[4] = 32 seconds
[3] = 24 seconds
[5] = 40 seconds
[6] = 48 seconds
[7] = 56 seconds
[8] to [F] = 60 seconds
[ENTER] + Installer Code + [10] [10] [3] + 1st digit + 2nd digit (1-15 rings) + [ENTER]
The second digit represents the number of rings the control panel will wait before picking-up the line. If the line is not answered
after the number of re-programmed rings, the control panel will answer the call. Note the control panel resets the "ring" counter
every 64 seconds. Therefore, if someone or an answering machine answers a call before the number of pre-programmed rings
has elapsed, the control panel will keep the number of rings in memory for 64 seconds. If you hang-up and call the installation site
back within 64 seconds, the control panel will continue to count the number of rings from the first call. After reaching the total
number of rings, the control panel will answer the call. The number of rings can be set from 1-15 by programming the second digit
at address 003 with any hexa-digit from 1-F. Program the second digit with [2nd] to disable this option.
Example: Address 003 = [2nd] [8]. Using the Espload software, you call an installation site where there is no answering
machine or service and no one is home. Since there is no one to answer the telephone call, the control panel will pick-up
the line on the eighth ring. If someone happens to be home and answers the telephone, say, after three rings, the control
panel will keep the three rings in memory for 64 seconds. If you hang-up and call back the installation site within 64
seconds the control panel will answer the call on the fifth ring. If you call back after 64 seconds the "ring" counter will
have been reset and the control panel will answer the call on the eighth ring.
If you program four or less rings, the control panel will always reset the counter
5.2
Panel Identifier
Streamline - Section 01 D Hexa Programming - Addresses 004-005
This four-digit code identifies the control panel to the Espload software before initiating upload. Program the same 4-digit code
into the control panel and the Espload software before attempting to establish communication. If the codes do not match, the
control panel will not establish communication. Enter any hexa digits from 0 to F.
[ENTER] + Installer Code + [10] [10] [4] + First 2 digits + [10] [10] [5] + Final 2 digits + [ENTER]
Esprit 748+
15
5.3
PC Password
Streamline - Section 01 D Hexa Programming - Addresses 006-007
This four-digit download password identifies the PC to the panel, before beginning the download process. Enter the same
password into the Espload software and the control panel. If the passwords are not the same, Espload will not establish
communication. Enter any hexa digits from 0 to F.
[ENTER] + Installer Code + [10] [10] [6] + First 2 digits + [10] [10] [7] + Final 2 digits + [ENTER]
5.4
Computer Telephone Number
Streamline Section 02 & 03 D Hexa Programming - Address 008-015
The control panel will dial this telephone number when trying to initiate communication with the PC (see section 5.5 Call
Espload). There is no default telephone number and you can enter any number from 0-9 up to a maximum of 16 digits. If you
would like to enter any special keys or functions refer to table 3 in section 6.3. If the telephone number contains less than 16
digits, press the [trbl] key to indicate the end of the telephone number.
[ENTER] + Installer Code + [7] + [10] [2] + Telephone Number (if <16 digits press [TRBL]) + [ENTER]
5.5
Call Espload
Key Access Programming D key [TRBL]
The control panel will dial the telephone number entered at addresses 008-015 (see section 5.4) in order to communicate with the
Espload software. The control panel and the computer will verify that the Panel Identifier and the PC Password match before
establishing communication (see sections 5.2 and 5.3).
Press [ENTER] + (Installer, Master, or User 1 Code) + [TRBL]/[TBL]
5.6
Answer Espload
Key Access Programming D key [AWAY]
By entering the code sequence listed below, you can manually force the control panel to answer any incoming calls from the
Espload software. This option can also be used to perform an on-site upload/download by connecting your computer directly to
the control panel using an ADP-1 line adapter and manually answering Espload from the control panel. In Espload go to:
Main Menu - Program Setup - Modem & Printer Configuration
Set "Dialing Condition" to "Blind Dial". Program the panel telephone number in Espload and follow the instructions on the ADP-1
adapter. When the computer has dialed press:
[ENTER] + (Installer, Master, or User 1 Code) + [AWAY]
5.7
Cancel Communication
Key Access Programming D key [STAY]
Use the Installer Code to cancel all communication and erase any unreported events in the buffer until the next reportable event.
Use the Master or User 1 code to cancel communication attempts with Espload.
[ENTER] + (Installer, Master & User 1 Code) + [STAY]
5.8
Call Back
Feature Select Programming D Address 086, key [4]
Default: Call Back Disabled
For additional security, when a PC using the Espload software attempts to communicate with the control panel, the control panel
can hang-up and call the PC back in order to re-verify identification codes and re-establish communication. When the control
panel answers the call, it will verify if the Panel ID and PC Passwords match and if they do, the control panel will hang-up and call
the Espload software back. The Espload software will automatically go into "wait for dial tone", ready to answer when the control
panel calls back. Please note the Computer Telephone Number (see section 5.4) must be programmed in order to use the "Call
Back" feature.
Key [4] "Off": Call Back Disabled
Key [4] "On": Call Back Enabled
[ENTER] + Installer Code + [10] [8] [6] + [4] On/Off + [ENTER] twice
16 Reference & Installation Manual
5.9
Automatic Event Buffer Transmission
Feature Select Programming D Address 088, key [2nd]
Default: Automatic Event Buffer Transmission Disabled
When the event buffer reaches 50% capacity, the control panel will make two attempts to establish communication with a PC. The
control panel will call the Computer Telephone Number (see section 5.4) programmed at addresses 008 to 015. The Espload
software must be in "wait for dial tone" mode. When the system establishes communication, it will upload the contents of the
event buffer to the Espload software. If communication is interrupted before transmission of the complete contents of the buffer,
or if after two attempts, communication is not established, the system will wait until the event buffer is full before attempting to recommunicate with Espload. When the Event Buffer is full, each subsequent new event will erase the oldest event in the buffer.
Key [2nd] "Off": Automatic Event Buffer Transmission Disabled
Key [2nd] "On": Automatic Event Buffer Transmission Enabled
[ENTER] + Installer Code + [10] [8] [8] + [2nd] On/Off + [ENTER] twice
Esprit 748+
17
Part 6: Event Reporting
Figure 23
NO
Account 1 and 2
Have the same number
YES
Account 1 and 2
Have the same number
or
System A = Account #1
System B = Account #2
Partitioned
Section 08
Addresses
032 to 035
Monitoring Station Telephone Number #1
Sections 04 & 05; Addresses 016 to 023
Phone Number
Monitoring Station Telephone Number #2
Sections 06 & 07; Addresses 024 to 031
Control panel will never
transmit report codes
Disabled
OFF/OFF
Related Features
Alternate between the two
monitoring station numbers until
communication is achieved
beginning with Monitoring #1
Regular
OFF/ON
Reporting
Events
Reporting Options
Address 086
Keys [STAY] &
[AWAY]/[FORCE]
When system is in alarm,
Monitoring Station Telephone #1
will be dialed until communication
is achieved
Split
ON/OFF
When system is not in alarm,
Monitoring Station Telephone #2
will be dialed until communication
is achieved
Manual Test Report
[BYP] Key Access
Power Failure Report Delay
Address 054
Recent Close Delay
Address 060
Report Zone Restore Options
Address 088; [BYP]
Report Disarm Option
Address 088; [TBL] / [TRBL]
Will send the report code to both
monitoring stations starting with
Monitoring #1
Doubled
ON/ON
[2ND] = Ademco Slow
[2] = Silent Knight Fast
Pulse
Auto Test Report
Addresses 046 to 048
[3] = SESCOA
Valid report codes must be
programmed into the
addresses corresponding
to the reportable events
[4] to [7] = Radionics
Communication
Format
Address 038
1st digit = Monitoring 1
2nd digit = Monitoring 2
[1] = 1400Hz to 1800Hz
[8] = Ademco Express
DTMF
(Tone)
[0] = Ademco Contact I.D.
(all codes)
Section 11 to 67
Addresses 300 to 527
Addresses 300 to 527 do not need to
be programmed
[9] = Ademco Contact I.D.
Programmable
[TRBL] = Pager
Valid codes corresponding to the
Contact I.D. table (Table 7 on page 22)
must be programmed in the addresses
corresponding to the reportable events
Sections 11 to 67
Addresses 300 to 527
18 Reference & Installation Manual
6.1
Reporting Options
Feature Select Programming D Address 086, key [11] & [12]
Default: Reporting Disabled
When a specific event occurs in the system, the control panel will attempt to report the appropriate event code (if programmed) to
the Monitoring Station. The four available Reporting Options described in the table below, define where the event codes are
reported. In order to establish communication with the Monitoring Station the control panel will first access a telephone line and
wait a maximum of 8 seconds for a dial tone. If a dial tone is recognized or if after 8 seconds there is no dial tone, the control
panel will dial the appropriate Monitoring Station Telephone Number as defined by the Reporting Options listed in the table below.
If communication is established, the control panel will transmit the events in the event buffer to the Monitoring Station. If
communication fails during transmission, the control panel will dial the next monitoring station telephone number, as defined by
the reporting options listed below, and report only those events not reported during the interrupted attempt. For information on
Reporting Event Codes see section 6.6.
[ENTER] + Installer Code + [10] [8] [6] + [11] & [12] On/Off + [ENTER]
Table 4 - Reporting Options
6.1.1
Reporting Disabled
The Control Panel will never transmit any event codes to the monitoring station.
6.1.2
Regular Reporting
Using regular reporting the event codes are reported to the monitoring station using either telephone number 1 or 2.
The control panel will begin by dialing monitoring station telephone number 1. If communication fails, the dialer will
hang up, wait a predetermined period and dial monitoring station telephone number 2. This sequence will repeat 4
times, switching back and forth between the 1st and 2nd number (see Figure 24 on the following page) until
communication is established. After eight unsuccessful attempts, the redial sequence ends and a "communicator
report failure" will appear in the keypad's trouble display (key [7] "on"). When the next event occurs (reportable or nonreportable), the control panel will begin the dialing sequence again.
6.1.3
Split Reporting
When the system is not in alarm, the control panel will report all Event Codes to Monitoring Station Telephone 2. If
communication fails, the dialer will hang-up, wait a predetermined period and dial the number again. The control panel
will dial the number eight times until communication is established (see Figure 24 on the following page). After eight
unsuccessful attempts, the redial sequence ends and a "communicator report failure" will appear in the keypad's
trouble display (key [7] "on"). When the next event occurs (reportable or non-reportable), the control panel will begin
the dialing sequence again.
When the system is in alarm, the control panel will report all Event Codes to Monitoring Station Telephone 1. Any
ongoing communication (upload/download or reporting to Telephone 2) will stop immediately and the panel will dial
Telephone 1. If communication fails, the dialer will hang-up, wait a predetermined period and dial the number again.
The control panel will dial the number eight times until communication is established (see Figure 24 below). After eight
unsuccessful attempts, the redial sequence ends and a "communicator report failure" will appear in the keypad's
trouble display (key [7] "on"). When the next event occurs (reportable or non-reportable), the control panel will begin
the dialing sequence again.
6.1.4
Double Reporting
In double reporting, the control panel will report each event code to both monitoring station telephone numbers. The
control panel will begin by attempting communication with monitoring station telephone 1 and if communication fails,
the dialer will hang-up, wait a predetermined period and dial the number again. The control panel will dial the number
eight times until communication is established (see Figure 24). After eight unsuccessful attempts, the redial sequence
ends and a "communicator report failure" will appear in the keypad's trouble display (key [7] "on"). If communication
has been established and the event codes transmitted or if after eight attempts communication has not been
established, the control panel will report the same Event Codes to Monitoring Station Telephone 2.
Esprit 748+
19
Figure 24
6.2
Monitoring Station Telephone Number 1
Streamline - Section 04 & 05 D Hexa Programming - Addresses 016-023
The control panel will dial the programmed telephone number when reporting an event code to the monitoring station computer
(see Reporting Options in section 6.1). For example, if the alarm system is armed and a zone with a motion detector opens, the
control panel may dial the telephone number in order to send the programmed event code to the monitoring station computer.
There is no default telephone number and you can enter any number from 0-9 up to a maximum of 16 digits. If you would like to
enter any special keys or functions, refer to table 5 below. If the telephone number contains less than 16 digits, press the [trbl] key
to indicate the end of the telephone number.
[ENTER] + Installer Code + [7] + [10] [4] + Telephone Number + [ENTER] OR [TRBL] if number is <16 digits
6.3
Monitoring Station Telephone Number 2
Streamline - Section 06 & 07 D Hexa Programming - Addresses 024-031
The control panel can communicate with two monitoring station numbers. The control panel may at times dial the second number
depending on the selected Reporting Options see section 6.1. If the monitoring station does not have a second number, you must
enter the same number as the first. There is no default telephone number and you can enter any number from 0-9 up to a
maximum of 16 digits. If you would like to enter any special keys or functions refer to table 3 below. If the telephone number
contains less than 16 digits, press the [trbl] key to indicate the end of the telephone number.
[ENTER] + Installer Code + [7] + [10] [6] + Telephone Number + [ENTER] OR [TRBL] if number is <16 digits
Table 5 - Telephone Number Special Instruction
Enter special instructions in the telephone numbers using these keys:
= switch from pulse to tone while dialing
[0]
= the number “0”
[BYP]
=*
[MEM]
= pause 4 seconds
[STAY]
[AWAY]/[FORCE] = #
[TBL]/[TRBL] = end of telephone number
20 Reference & Installation Manual
Both Monitoring Station Telephone Numbers must be programmed in order for event reporting to function
properly
6.4
System Account Codes
Streamline - Section 08 D Hexa Programming - Addresses 032-035
All report codes are preceded by a 3 or 4-digit system account code to ensure correct identification to the monitoring station,
identifying from which security system the event originated. For example, if a zone opens, the control panel will first send the
account code followed by the appropriate report code. In a partitioned system, the control panel can send a separate account
code for each system. This will identify to the monitoring station from which partition the report code originated. To do so, program
a different number into each account code. Where account code #1 will represent “System A" and account code #2 will represent
“System B".
If partitioning is disabled, program the same value for both account numbers.
There are no defaults and you can enter any hexa digit from 0 to F. Please note if required, system account codes can have 3
digits. To do so, press the [2nd] key followed by the 3-digit account number.
[ENTER] + Installer Code + [7] + [10] [8] + 4-digit Account Code #1 + 4-digit Account Code #2 + [ENTER]
[ENTER] + Installer Code + [7] + [10] [8] + [2nd] + 3-digit Account Code #1 + [2nd] 3-digit Account Code #2 + [ENTER]
6.5
Communicator Formats
Streamline - Section 09 D Hexa Programming - Address 038
Default: Ademco Slow for both numbers
The following option will determine which format the control panel will use to communicate with the Monitoring Station. You can
select a different communicator format for each Monitoring Station Telephone Number. Using table 4 below, select the
appropriate communication format. The first digit represents the Communication Format for Monitoring Station Telephone
Number 1 and the second digit represents the Communication Format for Monitoring Station Telephone Number 2. Below you will
find a brief description of all available Communicator Formats.
[ENTER] + Installer Code + [10] [3] [8] + First digit = (Monitoring Station Telephone #1) + Second digit = (Monitoring Station
Telephone #2) + [ENTER]
Key
[2ND]
[1]
[2]
[3]
[4]
[5]
Table 6 - Communicator Formats
Key
= ADEMCO slow (1400Hz, 1900Hz, 10bps)
[6]
= RADIONICS with PARITY (1400Hz, 40Bps)
= (1400Hz, 1800Hz, 10bps)
[7]
= RADIONICS with PARITY (2300Hz, 40Bps)
= SILENT KNIGHT fast (1400Hz, 1900Hz, 20bps)
[8]
= * ADEMCO express
= SESCOA (2300Hz, 1800Hz, 20bps)
[9]
= * ADEMCO contact ID (programmable codes)
= RADIONICS (40Bps with 1400Hz handshake)
[0]
= * ADEMCO contact ID (all codes)
= RADIONICS (40Bps with 2300Hz handshake)
[TBL]/[TRBL] = * PAGER FORMAT - (personal dialing)
* = 4-digit account codes only
6.5.1
Ademco Contact ID (all codes)
Please note that this format must use a 4-digit system account code (see section 6.4). Ademco Contact ID is a fast
communicator format that uses tone transmission instead of pulse transmission. This communicator format also uses a
pre-defined list of industry standard messages and event codes that should suit most of your basic installation needs.
Using the "All Codes" format, the control panel will automatically generate the Contact ID event codes (see table 7
below) for every event in addresses 300 to 527. Therefore, you do not need to program addresses 300 to 527.
Esprit 748+
21
Table 7 - Contact ID Event Codes
Event Code Addresses Contact ID Message
System Event
Alarms/Restores
400 to 447
Alarm/Restore on Zone 3 if 24Hr fire or 2-wire
Arm/Disarm
402, 426
301 to 349 / 351 to 399
Burglary Zone #
Contact ID Code #
130
Fire Alarm
110
Open/Close By User #
401
Zone Shutdown
448 to 471
Burglary Bypass #
573
Zone Tamper
472 to 495
Sensor Tamper
383
383
Zone Tamper Reset
510
Sensor Tamper
Auxiliary Power Trouble
496 and 504
System Trouble
300
Bell Disconnect/Max. Current Trouble
497 and 505
Bell 1 Trouble
321
Low Battery
498 and 506
Low System Battery
302
AC Fail
499 and 507
AC Loss
301
Fire Loop Trouble
500 and 508
Fire Loop Trouble
373
Timer Loss/Timer Programmed
501 and 509
Time/Date Reset
625
TLM Trouble Restore
511
Telco 1 Fault
351
Test Report
512
Periodic Test
602
Panic #1 (keys 1 and 3)
513
Panic Alarm
120
Panic #2 (keys 4 and 6)
514
Medical
100
Panic #3 (keys 7 and 9)
515
Fire Alarm
110
Duress
520
Duress
121
Late to Close or No Movement
Late to Open/Close
404
Partial Arming
518
Group Bypass
574
Recent Close
519
Open/Close
400
Espload Log-In
524
Remote Access
410
Program Change
525
Program Changed
306
6.5.2
516 and 517
Ademco Contact ID (programmable codes)
Please note that this format must use a 4-digit system account code (see section 6.4). Ademco Contact ID is a fast
communicator format that uses tone transmission instead of pulse transmission. Use the Ademco Contact event list of
industry standard messages and event codes found in the programming guide to program the desired event codes into
addresses 300 to 527.
6.5.3
Ademco Express
This high-speed reporting format communicates 2-digit (00 to FF) events programmed at addresses 300 to 527 at a
speed of 2 seconds per event. Unlike other Ademco formats, the Contact ID Event Codes are not used. Please note
this format must use a 4-digit system account code (see section 6.4).
6.5.4
DTMF - no handshake
This format is the same as the Ademco contact ID (programmable codes) except there is no verification of the report
code sent (no handshake). Use this format in reporting situations where a monitoring station receiver is not connected
to the telephone number. It is also useful for personal reporting where a "handshake" is not required. For example, in
"double reporting" mode, the first monitoring station number can be connected to a receiver, while the second can be
used for personal reporting using "no handshake" format. The panel will make two attempts to call the "no handshake"
number. Please note this format must use a 4-digit system account code (see section 6.4).
6.5.5
Standard Pulse Formats
The control panel supports the following pulse reporting formats (see table 4 on the previous page): Ademco slow,
Silent Knight, Sescoa, and Radionics.
6.6
Reporting Event Codes
Streamline - Sections 11 to 67 D Hexa Programming - Addresses 300-527
An Event Code is a 2-digit hexadecimal value, consisting of numbers from 00-FF. Each address between 300 and 527 represents
a specific event, as described below and in the "Programming Guide". When an event occurs in the system, the control panel will
attempt to transmit the 2-digit Event Code programmed at the corresponding address to the monitoring station. The method of
Event Code transmission is dependent on the Communicator Formats (see section 6.5) and the Reporting Options (see section
6.1).
22 Reference & Installation Manual
Note:You do not need to program addresses 300-527 if using the Ademco Contact I.D. (all codes) format. If you plan to program
most of the event code addresses, we suggest you use the Hexa Streamlined Section Programming Method as described in
section 4.2.2. Otherwise, use the Hexa Programming Method as described in section 4.2.1.
6.6.1
Arming Codes
Streamline - Sections 11 to 23 D Hexa Programming - Addresses 300-349
Whenever the system is armed, the control panel will send the programmed event code to the Monitoring Station
identifying who or how the system was armed.
6.6.2
Disarming Codes
Streamline - Sections 23 to 35 D Hexa Programming - Addresses 350-399
Whenever the system is disarmed, the control panel will send the programmed event code to the Monitoring Station
identifying who disarmed the system.
6.6.3
Alarm Codes
Streamline - Section 36 to 41 D Hexa Programming - Addresses 400-423
Whenever an alarm occurs, the control panel will send the programmed event code to the Monitoring Station
identifying which zone generated an alarm.
6.6.4
Restore Codes
Streamline - Sections 42 to 47 D Hexa Programming - Addresses 424-447
The control panel will send the programmed event code to the Monitoring Station as soon as the zone closes after
having generated an alarm or as soon as the zone closes after bell cut-off. For more information, please see Report
Zone Restore Options in section 6.11.
6.6.5
Shutdown Codes
Streamline - Sections 48 to 53 D Hexa Programming - Addresses 448-471
If the Auto Zone Shutdown (see section 7.11.1) feature is enabled, the control panel will send the programmed event
code to the Monitoring Station identifying which zones were shutdown.
6.6.6
Tamper/Trouble Codes
Streamline - Sections 54 to 56 D Hexa Programming - Addresses 472-483
If the Tamper/Wire Fault Recognition Options are disabled (see section 10.7), the control panel will never transmit
these event codes. Otherwise, whenever a tamper occurs on a zone, the control panel will send the programmed
Event Code to the Monitoring Station. With Advanced Technology Zoning (ATZ) enabled (see section 7.2) each
Tamper Code address will represent two zones (e.g. Tamper 1 = zones 1 & 2, Tamper 2 = zones 3 & 4, etc.). The
control panel will send the programmed Event Code when a tamper occurs on either zone.
6.6.7
Trouble/Restore Codes
Streamline - Sections 60 to 63 D Hexa Programming - Addresses 496-511
Each of the these addresses represent a specific trouble or restore condition. The control panel will report the
appropriate event code to the monitoring station when one of the following conditions occurs or after the condition has
returned to normal.
496 504 497 505 498 506 499 507 500 508 501 509 502 to 503 510 -
Max. Auxiliary Current: the current draw from auxiliary is ≥ 1.1A.
Max. Auxiliary Current Restore
Bell Disconnect/Max. Bell Current: Bell is disconnected or Bell current is ≥ 3A.
Bell Disconnect Restore: No restore code for bell current.
Battery Disconnect/Low Voltage: Battery disconnected or battery voltage ≤ 10.5V.
Battery Disconnect/Low Voltage Restore
Power Failure: Voltage on AC input is ≤ 12.5V.
Power Failure Restore
Fire Loop Trouble: A tamper occurs on a fire zone (Zone 3/24hr.).
Fire Loop Trouble Restore
Timer Loss: The control panel detects a loss in the panel timer.
Timer Programmed
Reserved for Future Use
All Tamper/Trouble Codes (see section 6.6.6) have returned to "normal".
Esprit 748+
23
511 -
6.6.8
TLM Trouble Restore: Telephone line has restored after the TLM (see section 10.1) has detected
the loss of a telephone line.
Special Codes
Streamline - Sections 64 to 67 D Hexa Programming - Addresses 512-527
Each address represents a special condition in the system. When one of these special conditions occur, the control
panel will report the event code associated with the address.
512 -
Test Report: The test report has been activated either manually (see section 6.8) or automatically
(see section 6.7).
513 Panic 1: Keys [1] and [3] or a PS1 is pressed to activate a Panic 1 alarm
514 Panic 2: Keys [4] and [6] are pressed to activate a Panic 2 alarm
515 Panic 3: Keys [7] and [9] are pressed to activate a Panic 3 alarm
For more information on Keypad Panic Options see section 10.4
516 517 518 519 520 524 525 521 to 523 526 to 527 -
6.7
Late To Close: "Timed" Auto Arming is enabled (see section 8.1) and the system has not
automatically armed itself at the specified time.
No Movement: "No Movement" Auto Arming is enabled (see section 8.2) and no movement has
occurred for the designated amount of time.
Partial Arming: Whenever the system is "Away" armed, "Stay" armed, or armed while one or more
zones are bypassed.
Recent Close: An alarm occurs shortly after the system has been armed, refer to Recent Close
Delay in section 6.10.
Duress: The Duress feature is enabled (see section 3.4) and a User disarms the system using the
User Code #48.
Log-In (Espload): Espload software is used to communicate with the Control Panel.
Program Change: The installer code is used to enter the programming mode
Reserved for Future Use
Reserved for Future Use
Auto Test Report
Decimal Programming D Addresses 046-048
Default: Auto Test Report Disabled
The report code programmed at address 512 will be reported to the monitoring station after the number of days programmed at
address 046 and the time programmed at address 047 (hours) and 048 (minutes) has elapsed. To disable this feature, program
000 at address 046. Also note that if [2nd][2nd] is programmed at address 512 nothing will be reported.
[ENTER] + Installer Code + [10] [4] [6] + 3 digits (days) + [10] [4] [7] + 3 digits (hours) + [10] [4] [8] + 3 digits (minutes) + [ENTER]
6.8
Manual Test Report
Key Access Programming D key [byp]
Activating the manual test report will send the Event Code programmed at address 512 to the Monitoring Station.
[ENTER] + (Installer, Master, or User 1 Code) + [BYP] + [ENTER]
6.9
Power Failure Report Delay
Decimal Programming D Addresses 054
Default: 30 minutes
After a power failure, the control panel will delay transmission of the event code programmed at address 499 by the
period programmed at this address (001 to 255 minutes).
[ENTER] + Installer Code + [10] [5] [4] + 3-digit decimal value (001-255) + [ENTER]
6.10
Recent Close Delay
Decimal Programming D Addresses 060
Default: Recent Close Delay Disabled
The system will transmit the recent close event code programmed at address 519 if after arming the system, an
alarm occurs within the period programmed at this address (001 to 255 minutes). Program 000 into address 060 tO
disable this feature.
[ENTER] + Installer Code + [10] [6] [10] + 3-digit decimal value (001-255) + [ENTER]
24 Reference & Installation Manual
6.11
Report Zone Restore Options
Feature Select Programming D Address 088; key [BYP]
Default: Zone Restore Codes Transmit on Bell Cut-Off
With the [BYP] key “Off”, the report codes programmed at addresses 424-447 (see Restore Codes in section 6.6.4) will only
transmit if the zone has returned to normal after bell cut-off (see section 8.11). With the [BYP] key “On”, the codes will transmit as
soon as the zone returns to normal (zone closure).
Key [BYP] "Off": Report on Bell Cut-Off
Key [BYP] "On": Report on zone closure
[ENTER] + Installer Code + [10] [8] [8] + [BYP] On/Off + [ENTER]
6.12
Report Code Disarming Options
Feature Select Programming D Address 088; key [TRBL]
Default: Disarming Codes Transmit on User Disarming
With the [TRBL] key "OFF", the Disarming Codes programmed at addresses 350-399 (see in section 6.6.2) will transmit whenever
a User disarms the system. With the [TRBL] key "ON", the control panel will transmit these codes when a User disarms a system
in alarm.
Key [TRBL] "Off": Always Report Disarm
Key [TRBL] "On": Report Disarm Only After Alarm
[ENTER] + Installer Code + [10] [8] [8] + [TRBL] On/Off + [ENTER]
Esprit 748+
25
Part 7: ZONE DEFINITIONS
Figure 25
Zone Speed
(applies to all zones)
Address 053
EOL Zones
(applies to all zone inputs)
Address 088; [MEM] key
ATZ Zone Doubling
(applies to all zone inputs)
Address 090; key [8]
Address 090; key [7]
Partitioning
(applies to entire system)
Address 086; key [8]
System A/Stay Zones
Address 116; Keys [1] to [10 (0)]
Note: If the system is not partitioned,
zones will be defined as Stay zones
System B Zones
Addresses 120; Keys [1] to [10 (0)]
Bypass Enabled Zones
Address 124
Keys [1] to [10 (0)]
Auto Zone Shutdown
Address 086; [TRBL] key
Zone Related
Features
Intellizones
Address 092
Keys [1] to [10 (0)]
Intellizone
Time Delay
Address 057
Silent Zones
Address 096
Keys [1] to [10 (0)]
Generates
Report Only
Address 086
Key [9]
Independent Zone
Definitions
Zone Definitions
Up to 10 zones can be
independently
programmed (defined).
Only one of these options
can be assigned to a
zone. If a zone is assigned
more than one option, the
control panel will apply the
option with the highest
priority (1 to 5).
Keypad Zone 1 & 2 Supervision
Enabled/Disabled
Address 090;
Keys [STAY] & [AWAY]/[FORCE]
26 Reference & Installation Manual
24Hr/Fire Zones
Address 100
Keys [1] to [10 (0)]
Instant Zones
Address 104
Keys [1] to [10 (0)]
Follow Zones
Address 108
Keys [1] to [10 (0)]
Enable/
Disable
Zone 4
Address 090
Key [1]
Only if zone
3 is defined
fire zone and
ATZ is
enabled
Delay 2 Zones
Address 112
Keys [1] to [10 (0)]
Entry Delay 2
Timer
Address 051
Delay 1 Zones
Zone not defined as
any of the above will
default to Delay 1
Entry Delay 1
Timer
Address 050
7.1
Zone Speed
Decimal Programming D Address 053
Default: 600mS
The zone speed applies to all zones whether the system is armed or disarmed. The zone speed defines how quickly the control
panel will respond to an open zone. The control panel will not display and/or respond to an open zone until the programmed zone
speed elapses. All other zone definitions and options do not come into effect until the zone speed has elapsed.
Example: The system is armed and the zone speed is set for 1.2 seconds. A zone opens and closes in less than 1.2
seconds the control panel will not respond (i.e. no reporting, no alarm and no display on keypad).
The zone speed can be set from 15ms to 3.8s (001 to 255 X 15ms). This feature prevents any momentary glitches in the system
from causing an alarm or unnecessary reporting.
[ENTER] + Installer Code + [10] [5] [3] + 3 digit decimal value (001-255) + [ENTER]
7.2
Advanced Technology Zoning (ATZ)
Feature Select Programming D Address 090, key [8]
Default: ATZ Disabled
Enabling the ATZ feature allows you to install two detection devices per zone input. Each detection device will have its own zone
number and each will transmit a separate alarm code that will display on the keypad. For information on how to connect the
detection devices and how the panel recognizes them, please refer to section 2.10.
Key [8] "Off": ATZ Disabled
Key [8] "On": ATZ Enabled
[ENTER] + Installer Code + [10] [9] [10] + [8] On/Off + [enter]
7.3
Intellizones
Feature Select Programming D Addresses 092 & 094, keys [1] to [12]
If an alarm condition occurs on a zone identified as Intellizone, the control panel will trigger a timer and will not generate an alarm
until one of the following conditions occurs within a specified period (see Intellizone Time Delay below):
• An alarm condition occurs on another zone during intellizone time delay.
• The zone that is in alarm has restored and re-occurred during intellizone time delay.
• The zone that is in alarm remains in alarm the entire intellizone time delay.
Note: Intellizone timer will only begin after the zone speed period has elapsed (see section 7.1).
Do not use the Intellizone feature on zones programmed with any Entry Delay. An alarm may occur when
disarming the system.
7.3.1
Intellizone Time Delay
Decimal Programming - Address 057
Default: 48 seconds
You can set the Intellizone Time Delay between 010 and 255 seconds. Before an Intellizone can generate an alarm,
one of three conditions must occur during this time delay (see section 7.3).
[ENTER] + Installer Code + [10] [5] [7] + 3-digit decimal value (010-255) + [ENTER]
7.4
Silent Zones
Feature Select Programming D Addresses 096 & 098, keys [1] to [12]
Using the "Feature Select Programming Method", select which zones will be defined as Silent Zones. If an alarm occurs on a
Silent Zone, the control panel will report the alarm (see Event Reporting in section 6) to the monitoring station without triggering
any bells and/or sirens. Note if zone 3 is defined as 24 hour (fire zone), the control panel will generate an audible alarm,
overriding a silent zone definition.
7.5
24 Hour & Fire Zones
Feature Select Programming D Addresses 100 & 102 , keys [1] to [12]
Using the "Feature Select Programming Method", select which zones will be defined as 24 hour Zones. Keypad zones should
not be programmed as 24hr zones. Regardless of the system’s armed status, an open “24hr” zone will always generate an
alarm.
If zone 3 is defined as "24 hour", it becomes a "Fire Zone". Connect the smoke detectors as described in section 2.11. An open
"Fire Zone" will generate the following:
Esprit 748+
27
•
•
•
•
The panel will send a fire loop trouble report (if programmed at address 500) to the Monitoring Station.
A trouble indicator, key [11], and a fire zone indicator, key [3], will flash on the keypad.
Alarms will generate an intermittent output signal (see Figure below), regardless of the system's current arming status.
Alarms are always audible, regardless of other settings.
Figure 26
7.5.1
Zone 15 (Enable/Disable)
Feature Select Programming D Address 090, key [1]
Default: Zone 15 Enabled
If the ATZ feature is enabled and zone 3 has been set as a fire zone, zone 15 must be disabled if it is not going to be
used.
Key [1] "Off": Zone 15 Enabled
Key [1] "On": Zone 15 Disabled
[ENTER] + Installer Code + [10] [9] [10] + [1] On/Off + [ENTER]
7.6
Instant Zones
Feature Select Programming D Addresses 104 & 106, keys [1] to [12]
Using the "Feature Select Programming Method", select which zones will be defined as Instant Zones. If an "Instant" zone opens,
the control panel will immediately generate an alarm after the "Zone Speed" has elapsed.
7.7
Follow Zones
Feature Select Programming D Addresses 108 & 110, keys [1] to [12]
Using the "Feature Select Programming Method", select which zones will be defined as Follow Zones. Follow zones function as
follows:
• If a follow zone opens and no entry delay zones have been triggered; the control panel will immediately generate an alarm
after the zone speed has elapsed.
• If a follow zone opens during another zone's entry delay period, the control panel will wait until the end of the entry delay
period before generating an alarm.
• If a follow zone opens when more than one entry delay zone has been triggered, the panel will wait until the end of the entry
delay zone that opened first before generating an alarm.
7.8
Entry Delay 1
Decimal Programming D Address 050
Default: 45 seconds
Any zone that has not been identified as either Instant Zones, Follow Zones, Entry Delay 2, or "24 Hour" & Fire Zones (see
above) will automatically default to Delay 1. You can program the Delay 1 period between 001 and 255 seconds into address
050. If a zone defined as Delay 1 opens in an armed system, the control panel will wait the pre-programmed period before
generating an alarm. This provides the users the time required to disarm the system when entering the protected area.
[ENTER] + Installer Code + [10] [5] [10] + 3-digit decimal value (001-255) + [ENTER]
7.9
Entry Delay 2
Feature Select Programming D Addresses 112 & 114, keys [1] to [12]
Using the "Feature Select Programming Method", select which zones will be defined as Entry Delay 2 Zones. If a zone defined as
Delay 2 opens in an armed system, the control panel will wait the Entry Time Delay 2 (see below) period before generating an
alarm. This provides the users the time required to disarm the system when entering the protected area.
28 Reference & Installation Manual
7.9.1
Entry Time Delay 2
Decimal Programming D Address 051
Default: 45 seconds
This applies to all zones defined as Delay 2 (see Entry Delay 2 above). You can program the Delay 2 between 001 and
255 seconds.
[ENTER] + Installer Code + [10] [5] [1] + 3-digit decimal value (001-255) + [ENTER]
7.10
Partitioning
Feature Select Programming D Address 086, key [8]
This feature divides the alarm system into two distinct systems, identified as "System A" and "System B". You can assign each
zone to System A, System B, both systems, or neither system. Partitioning works as follows:
• Zones assigned to System A, will arm/disarm when the system is "System A Armed/Disarmed".
• Zones assigned to System B, will arm/disarm when the system is "System B Armed/Disarmed".
• Zones assigned to both systems ("dual area") will arm when the system is either "System A Armed", "System B Armed" or
when both systems are armed and will disarm only when both systems disarm.
• Zones not identified to any system ("common area") will arm only when the system is both "System A Armed" and "System B
Armed" and will only disarm when at least one of the two systems disarms.
For more information on arming and disarming partitions, see section 11.5. Also see Code Priority in section 8.12.
7.10.1
System A/Stay Zones
Feature Select Programming D Addresses 116 & 118, keys [1] to [12]
Using the "Feature Select Programming Method", select which zones will be assigned to "System A" or if the system
isn’t partitioned which zones will be identified as Stay Zones. For details on "System A" zones refer to Partitioning
above. For details on Stay Arming see section 11.4.
7.10.2
System B Zones
Feature Select Programming D Address 120 & 122, keys [1] to [12]
Using the "Feature Select Programming Method", select which zones will be assigned to "System B". For details on
"System B" zones refer to Partitioning above.
7.11
Bypass Enabled Zones
Feature Select Programming D Addresses 124 & 126, keys [1] to [12]
Using the "Feature Select Programming Method", select which zones will be defined as Bypass Enabled. Only
zones defined as bypass enabled can be used for Manual Zone Bypassing (section 11.9) or during Auto Zone
Shutdown (see below).
7.11.1
Auto Zone Shutdown
Feature Select Programming D Address 086 key [trbl]
Default: Auto Zone Shutdown Disabled
The control panel will automatically bypass any "Bypass Enabled Zones" which initiate 5 consecutive alarms in the
same-armed period. Therefore, the zone will no longer generate an alarm. After the control panel has bypassed a
zone, it will report an event code to the Monitoring Station if programmed at addresses 448-461.
This feature is also a function of the Report Zone Restore Options (see section 6.11). If this option is set for report
zone restore on bell cut-off, the zone will only be bypassed after the bell or siren has cut-off 5 consecutive times in
the same armed period. While if the option is set for report zone on zone closure, the zone will be bypassed when
the zone has opened and closed 5 consecutive times in one armed period. The Auto Zone Shutdown counter resets
when the system is disarmed.
Key [trbl] "Off": Auto Zone Shutdown Disabled
Key [trbl] "On": Auto Zone Shutdown Enabled
[ENTER] + Installer Code + [10] [8] [6] + [TRBL] On/Off + [ENTER]
7.12
EOL Zones (Enabled/Disabled)
Feature Select Programming D Address 088; key [mem]
If the system requires the use of 1KW end of line resistors on zone input terminals, enable this feature (see Zone
Connections in sections 2.8 to 2.10).
Key [MEM] "Off": Input Zones use EOL Resistors
Key [MEM] "On": Input Zones do not use EOL Resistors
[ENTER] + Installer Code + [10] [8] [8] + [MEM] On/Off + [ENTER]
Esprit 748+
29
7.13
Keypad Zone 1 Supervision
Feature Select Programming D Address 090, key [11]
Default: Disabled
When using a keypad defined as keypad zone 1, enable this feature. When enabled, the control panel will verify the
presence of a keypad and the keypad zone. For more information see Keypad Zone Connections in section 2.8.
Key [11] "Off": Keypad Zone 1 Disabled
Key [11] "On": Keypad Zone 1 Enabled
[ENTER] + Installer Code + [10] [9] [10] + [11] On/Off + [ENTER]
7.14
Keypad Zone 2 Supervision
Feature Select Programming D Address 090, key [12]
Default: Disabled
When using a keypad defined as keypad zone 2, enable this feature. When enabled, the control panel will verify for the presence
of a keypad and the keypad zone. For more information see Keypad Zone Connections in section 2.8.
Key [12] "Off": Keypad Zone 2 Disabled
Key [12] "On": Keypad Zone 2 Enabled
[ENTER] + Installer Code + [10] [9] [10] + [12] On/Off + [ENTER]
30 Reference & Installation Manual
Part 8: ARM/DISARM & ALARM OPTIONS
Figure 27
Esprit 748+
31
8.1
Timed Auto Arming
Feature Select Programming D Address 086, key [5]
Default: "Timed" Auto Arming Disabled
The alarm system will automatically arm itself at a specified time everyday. Note, as with regular arming, the system will not arm
if a zone is open and will report a "late to close" to the monitoring. If this occurs, the system will not arm until the next day. The
type of arming is dependent on the Auto Arming Options (see below). Program the Auto Arm Time as described below.
8.1.1
Auto Arm Time
The control panel will automatically arm itself at the specified time if "Timed" Auto Arming (see above) is enabled. The
time is programmed using the 24-hour clock (i.e. 8:00PM = 20:00). There are two methods of programming the "Auto
Arm Time" as described below.
Decimal Programming D Address 044 & 045
Program the "Auto Arm Time" in hours into address 044 and the "Auto Arm Time" in minutes into address 045.
[ENTER] + Installer Code + [10] [4] [4] + 3-digit decimal value (hours) + [10] [4] [5] + 3-digit decimal value (minutes) +
[ENTER]
Key Access Programming D key [9]
The User 1, Master, or Installer can program the "Auto Arm Time" using this method.
[ENTER] + (Installer, Master, or User 1 Code) + [9] + 2 digits representing hours + 2 digits representing minutes +
[ENTER]
8.1.2
Auto Arming Options
Feature Select Programming D Address 090, key [2]
Default: Regular Arming
The "Auto Arm" feature will arm the system as described in the table below.
Table 8 - Auto Arming Options
8.2
No Movement Auto Arming
Feature Select Programming D Address 086, key [6]
Default: Disabled
If the control panel does not detect any movement (zone openings) for a specified period, the panel will arm the system and
transmit the event code programmed at address 517. Note the type of arming is dependent on the Auto Arming Options (see
section 8.1.2). Program the "No Movement" Auto Arm Time as described below.
Key [6] "Off": No Movement Auto Arm Disabled
Key [6] "On": No Movement Auto Arm Enabled
[ENTER] + Installer Code + [10] [8] [6] + [6] On/Off + [ENTER]
8.2.1
No Movement Auto Arm Time
Decimal Programming D Address 055
Default: Disabled
000 = disabled; (001-255) X 15 minutes
If the "No Movement" Auto Arming (see above) feature is disabled and a time is programmed, the control panel will
transmit the event code programmed at address 517 if no movement is detected during the programmed period.
[ENTER] + Installer Code + [10] [5] [5] + 3-digit decimal value (001-255) + [ENTER]
8.3
One-Key Regular Arming
Feature Select Programming D Address 088, key [7]
Default: Disabled
A User can "Regular" arm the system by pressing and holding the [10] key for 2 seconds.
32 Reference & Installation Manual
Key [7] "Off": "One Key" Regular Arming Disabled
Key [7] "On": "One Key" Regular Arming Enabled
[ENTER] + Installer Code + [10] [8] [8] + [7] On/Off + [ENTER]
8.4
One-Key Stay/System A Arming
Feature Select Programming D Address 088, key [8]
Default: Disabled
Press and hold the [11] key for 2 seconds to "Stay" arm the system if partitioning is disabled. If the system is
partitioned, the control panel will arm System "A".
Key [8] "Off": "One Key" Stay/System A Arming Disabled
Key [8] "On": "One Key" Stay/System A Arming Enabled
[ENTER] + Installer Code + [10] [8] [8] + [8] On/Off + [ENTER]
8.5
Arming using a keyswitch
Feature Select Programming D Address 086, key [2] & [3]
Default: Disabled
The User can use a keyswitch to "Stay" arm or "Regular" arm/disarm the system. If the system is ready and the button is pressed
the system will arm. Pressing the button again will disarm the system. The keyswitch will not disarm a “Stay” armed system in
alarm. Refer to section 2.7 for installation of a keyswitch.
[ENTER] + Installer Code + [10] [8] [6] + [2] & [3] On/Off + [ENTER].
Table 9 - Keyswitch Arming
Key [2]
OFF
ON
OFF
ON
8.6
Key [3]
OFF
OFF
ON
ON
Function
Disabled
Disabled
Full Arming
Stay Arming*
Bell Squawk
Feature Select Programming D Address 086; key [mem]
Default: Disabled
With this feature enabled, the bell or siren will emit a half-second "squawk" upon arming and two half-second "squawks" upon
disarming.
Key [mem] "Off": Bell Squawk Disabled
Key [mem] "On": Bell Squawk Enabled
[ENTER] + Installer Code + [10] [8] [6] + [MEM] On/Off + [ENTER]
8.7
Exit Delay
Decimal Programming D Address 049
Default: 60 seconds
Exit Delay applies to all zones. This option determines how much time the user has to leave the protected area before the system
arms after entering a valid access code. You can program the Exit Delay from 001 to 255 sec.
[ENTER] + Installer Code + [10] [4] [9] + 3 digit decimal value (001-255) + [ENTER]
8.8
Beep on Exit Delay
Feature Select Programming D Address 088, key [12]
Default: Disabled
With this feature enabled, the keypad will emit an intermittent "beep" during the programmed exit delay period (except when in
"stay" arming). The frequency of intermittent beeps increases during the last 10 seconds of the exit delay period. For more
information on Exit Delay refer to section 8.7.
Key [12] "Off": Beep on Exit Delay Disabled
Key [12] "On": Beep on Exit Delay Enabled
[ENTER] + Installer Code + [10] [8] [8] + [12] On/Off + [ENTER]
Esprit 748+
33
8.9
Alarm Transmission Delay
Decimal Programming D Address 059
This time limit, set between 5 and 63 seconds, is the delay period before reporting an alarm to the monitoring station after an
alarm condition. During this period, disarming the system will cancel all pending alarms and send the restore codes.
Programming 000-004 in this address disables this feature. Maximum 30 seconds on UL listed systems.
[ENTER] + Installer Code + [10] [5] [9] + 3-digit decimal value (005-063) + [ENTER]
8.10
Silent Zones & Silent Panics Option
Feature Select Programming D Address 086, key [9]
If the [9] key is on, silent zones or silent panics only transmit a report to the monitoring station. The system will not indicate an
alarm and will not have to be disarmed.
Although, the control panel can still activate a PGM. If a keypad panic has been defined as audible, the control panel will override
this option.
Key [9] "Off": Silent Zones & Silent Panics generate a silent alarm
Key [9] "On": Silent Zones & Silent Panics generate a report only
[ENTER] + Installer Code + [10] [8] [6] + [9] On/Off + [ENTER]
8.11
Bell Cut-Off Time
Decimal Programming D Address 052
Default: 5 minutes
After an audible alarm, the bell or siren will stop after the programmed time has elapsed.
[ENTER] + Installer Code + [10] [5] [2] + 3-digit decimal value (001-255) minutes + [ENTER]
8.12
Code Priority
Feature Select Programming D Address 062-078, [all] keys
In order for a user to arm a partitioned system, to "Stay" arm, to "Away" arm or to manually bypass zones, the user must be given
code priority. Using the "Feature Select Programming Method", identify which arming method each user can use. For more
information on arming/disarming methods please refer to section 11. Also refer to the “Programming Guide” for additional
information.
• Partitioning Disabled:
Addresses 062-066: Selected keys indicate which user codes can activate "Stay" arming.
Addresses 068-072: Selected keys indicate which user codes can activate "Away" arming.
Addresses 074-078: Selected keys indicate which user codes can "Bypass" zones.
• Partitioning Enabled:
Addresses 062-066: Selected keys indicate which user codes can arm “System A".
Addresses 068-072: Selected keys indicate which user codes can arm “System B".
Addresses 074-078: Selected keys indicate which user codes can "bypass" zones.
34 Reference & Installation Manual
Part 9: PGM (PROGRAMMABLE OUTPUT)
We strongly suggest using of the Espload software to program the PGMs.
9.1
PGM Types
Streamline - Sections 09 - Hexa Programming - Address 039
These control panels have two programmable outputs (PGMs). When a PGM closes, a ground is supplied to activate any device
or relay connected to it, providing up to a maximum of 50mA (UL 30mA). When a PGM opens, the circuit is opened from ground,
therefore not providing any power to devices connected to it. To program a PGM you must define the PGM state (normally open
or normally closed), the timing (regular or timed) and you must define the type of logic ("OR", "AND", "EQUAL"). To do so, use
table 7 to determine which hexa digit to program into address 039, where the first hexa digit programmed corresponds to PGM1
and the second hexa digit corresponds to PGM2.
• Regular N.O./N.C.
A triggered PGM will switch to its opposite state (i.e. closed to open or opened to closed). The PGM will return to its original state
once the event(s) that triggered it have terminated.
• Timed N.O./N.C.
A triggered PGM will switch to its opposite state (i.e. closed to open or opened to closed). The PGM will remain in its opposite
state for the period programmed at address 056 (see section 9.2). If the PGM is triggered again before the period has elapsed,
the PGM will remain in its opposite state and reset the timer.
• "OR" Logic
Will trigger a PGM when at least one event occurs from a specific group of events (e.g. key [1] and/or key [2] is pressed on the
keypad).
• "AND" Logic
The "AND" logic will trigger a PGM when all events, or more, occur from a specific group of events (e.g. Keys [1] and [2] are
pressed simultaneously. Note that pressing those two keys in conjunction with any other key will also trigger the PGM).
• "EQUAL" Logic
The "EQUAL" logic will trigger a PGM only when the events from a specific group of events occur (e.g. Key [1] and [2] are
pressed. Note the PGM will only trigger when pressing keys [1] and [2] simultaneously, if any other key is pressed at the same
time (e.g. [1], [2] & [3]) the PGM will not trigger).
Table 10 - PGM Type Selection
Key
[2ND]
[1]
[2]
: OR
: AND
: EQUAL
[4]
[5]
[6]
: OR
: AND
: EQUAL
Reg. N.O.
Timed N.O.
Key
[8]
[9]
[0]
: OR
: AND
: EQUAL
Reg. N.C.
[AWAY/FORCE]
[BYP]
[MEM]
: OR
: AND
: EQUAL
Timed N.C.
(For timed PGM, see address 056 in section 9.2.)
[ENTER] + Installer Code + [10] [3] [9] + first digit (PGM1) + second digit (PGM2) + [ENTER]
9.2
PGM Timer Setting
Decimal Programming D Address 056
Default: 5 seconds
You can program the PGM Timer from 1 to 127 seconds or 1 to 127 minutes. The PGM Timer applies to both PGMs. To
determine the 3-digit decimal value, do the following:
• To program seconds, the required time is respective to the decimal value
1 second = 001, 55 seconds = 055, 127 seconds = 127.
• To program the minutes add the required minutes to 128:
5 minutes: 128 + 5 = 133
127 minutes: 128 +127 = 255
Esprit 748+
35
[ENTER] + Installer Code + [10] [5] [6] + 3-digit decimal value (001-255) + [ENTER]
9.3
PGM Options
Streamline - Section 10 D Hexa Programming - Addresses 040 to 043
The PGM options define which sequence of events will trigger the PGM. The PGM options are virtually endless. Therefore, to list
them in the manual is impractical. Table 8, contains a list of the most commonly used PGM options with the required 2-digit data
for each address. If other options are required, you can fax your requests to Paradox Technical Support, you can visit our web
site at www.paradox.ca. or the 2-digit data can be derived using the Espload Software as follows:
1) From the "Main Menu" select Accounts
2) Select a current Account or create a new one
3) Press the ‘Page Down’ key until page 9 appears
4) Using the arrow keys and space bar select the PGM options, state, logic and type for the PGM
5) Press the ‘F6’ key to view the "Hexadecimal Mode". This mode will display the 2-digit data for addresses 039 to 043.
6) Record these numbers and program them into the control panel or use the Espload Software to download the data directly to
the control panel.
If you do not have a copy of the Espload Software, you can obtain a FREE copy from your local Paradox distributor.
Table 11 - Commonly Used PGM Options
State
Option
Timed N.O.
Output enabled for 3 seconds before
communication attempt*
Regular N.O. Output enabled when keys [1] and [2] are
pressed simultaneously
Regular N.O. Output enabled when system armed
Regular N.O. Output enabled during an alarm
Timed N.O.
Output enabled for 2 minutes upon fail to
communicate
Regular N.O. Output enabled after one failed communication
attempt
Timed N.O.
Output enabled for 3 seconds after signal
received at monitoring station
*Not permitted on UL listed systems.
36 Reference & Installation Manual
PGM1
PGM2 (738 Ultra only)
add. 042
2nd digit
add. 039
add. 041
add. 043
[5] / [2]
[2ND] / [8]
[5]
[5] / [2]
[2ND] / [8]
[1]
[5] / [8]
[2ND] / [6]
[1]
[5] / [8]
[2ND] / [6]
[2ND]
[2ND]
[5]
[2] / [9]
[2] / [12]
[2] / [6]
[2ND] / [3]
[2ND] / [2]
[2ND] / [4]
[2ND]
[2ND]
[5]
[2] / [9]
[2] / [12]
[2] / [6]
[2ND] / [3]
[2ND] / [2]
[2ND] / [4]
[2ND]
[7] / [0]
[2ND] / [MEM]
[2ND]
[7] / [0]
[2ND] / [MEM]
[5]
[7] / [BYP]
[2ND] / [8]
[5]
[7] / [BYP]
[2ND] / [8]
1st digit
add. 039
add. 040
[5]
Part 10: OTHER OPTIONS
10.1
Telephone Line Monitoring (TLM)
Feature Select Programming D Address 086, key [2nd] & [1]
Default: TLM Disabled
When enabled, the system verifies the existence of a telephone line every 4 seconds. After each successful test, the dialer LED
(green light) on the control panel flashes briefly. If the test fails the LED flashes on and off until the control panel detects the
telephone line again. TLM will activate a trouble when less than 3 volts is detected in four consecutive tests.
Note: when the dialer detects a telephone ring, the TLM test stops for 1 minute.
There are three TLM options, which are set as indicated in table 9:
Table 12 - Telephone Line Monitoring (TLM)
Key
[2ND]
OFF
OFF
ON
ON
[1]
OFF
ON
OFF
ON
- TLM is disabled (default)
- TLM generates a trouble only
- generates an alarm if armed
- silent alarm becomes audible
(address 086, key [9] has to be OFF)
1) OFF/ON: Line test failure will generate a trouble indication; key [10] will illuminate on the keypad.
2) ON/OFF: Line test failure will generate a trouble indication and an alarm if the system is armed.
3) ON/ON: Line test failure will generate a trouble indication and cause a silent zone or a silent panic alarm to switch to audible
mode.
[ENTER] + Installer Code + [10] [8] [6] + [2nd] & [1] On/Off + [ENTER]
10.2
Dialing Options
Feature Select Programming D Address 086, key [7]
Default: Pulse Dialing
You can program the control panel to use the pulse dialing or tone/DTMF dialing format.
Key [7] "Off": Pulse Dialing
Key [7] "On": Tone/DTMF Dialing
[ENTER] + Installer Code + [10] [8] [6] + [7] On/Off + [ENTER]
10.3
Dialing Pulse Rates
Feature Select Programming D Address 086, key [10]
This selection reflects the ratio between "pulse" time and "quiet" time. Select Pulse Europe for a 1:2 ratio and select Pulse USA
for 1:1.5. Must be set to pulse dialing mode, refer to section 10.2.
Key [10] "Off": Pulse Europe 1:2
Key [10] "On": Pulse USA 1:1.5
[ENTER] + Installer Code + [10] [8] [6] + [10] On/Off + [ENTER]
10.4
Keypad Panic Options
Feature Select Programming D Address 088 keys [1] to [6]
This feature will generate an alarm when the User presses two specific keys on the keypad simultaneously for 2 seconds as
described below:
Key [1] "on" = Panic 1 (keys [1] and [3] or PS1) enabled
Key [2] "on" = Panic 2 (keys [4] and [6]) enabled
Key [3] "on" = Panic 3 (keys [7] and [9]) enabled
Keypad panic options:
Esprit 748+
37
Key [4] "off" = Panic 1 silent
Key [4] "on" = Panic 1 audible
Key [5] "off" = Panic 2 silent
Key [5] "on" = Panic 2 audible
Key [6] "off" = Panic 3 silent
Key [6] "on" = Panic 3 fire alarm
[ENTER] + Installer Code + [10] [8] [8] + [1] to [6] On/Off + [ENTER]
Silent operation:
When using the panic keys or the PS1, the control panel will emit a single confirmation beep. The control panel will transmit the
event codes programmed at addresses 513, 514, and 515. The alarm will latch (no audible alarm) and the "armed" light on the
keypad will flash until the system is disarmed by a valid User code.
Audible operation:
Same as silent operation, except the alarm output (bell/siren) will activate until the system is disarmed by a valid User code or
until the Bell Cut-Off Time (see section 8.11) elapses.
Fire operation:
Same as audible operation except that bell/siren output will be pulsed (see Fire Alarm Output Figure on page 28).
10.5
Panel Time
Key Access Programming D key [mem]
To program the current time into the control panel press:
[ENTER] + (Installer, Master, or User 1 Code) + [MEM] + 2 digits representing hours (00-23) + 2 digits representing minutes (00-59)
10.6
Time Correction
Streamline - Section 09 D Hexa Programming - Address 037
If you notice a gain or loss in the control panel time, calculate the average gain or loss per day; select the "opposite" amount from
the Time Correction table in order to automatically correct the time setting every 24 hours.
Example: The control panel loses 4 minutes per month, representing an average loss of 8 seconds per day. Therefore, program
[2] (plus 8 seconds) as the second digit in address 037 to compensate for the 8-second loss.
Table 13 - Time Correction Table
(address 037 2nd digit)
[2ND]
[1]
[2]
[3]
10.7
- No adjustment
- Plus 4 seconds
- Plus 8 seconds
- Plus 12 seconds
[4]
[5]
[6]
[7]
- Plus 16 seconds
- Plus 20 seconds
- Plus 24 seconds
- Plus 28 seconds
[8]
[9]
[0]
- Minus 4 seconds
- Minus 8 seconds
- Minus 12 seconds
[STAY] - Minus 16 seconds
[AWAY]/[FORCE]
[BYP]
[MEM]
[TBL/TRBL]
- Minus 20 seconds
- Minus 24 seconds
- Minus 28 seconds
- Minus 32 seconds
Tamper/Wire Fault Recognition Options
Feature Select Programming D Address 088, keys [10] to [11]
If the control panel detects an open or a short on a zone when the system is armed, regardless of the tamper/wire settings it will
always generate an alarm and trouble indicator (key [9]). Alarms will be audible or silent depending on individual zone definitions.
If an open or short occurs on a disarmed system, the control panel will generate an incident depending on the following settings:
Table 14 - Tamper Recognition Option
Key [10 (0)]
OFF
OFF
ON
ON
38 Reference & Installation Manual
Key [STAY]
OFF
ON
OFF
ON
- Tamper/Wire Fault disabled
- Trouble Indicator enabled
- Silent Alarm enabled
- Audible Alarm enabled
"Tamper/wire" disabled
Tamper/wiring failure recognition is disabled. Not permitted on UL listed systems.
"Trouble" enabled
Tamper/wiring failure will generate a trouble indicator (key [9]) and a trouble report code (see Tamper/Trouble Codes in section
6.6.6.) when the system is disarmed.
"Silent alarm" enabled
Tamper/wiring failure will generate a trouble indicator (key [9]), a trouble report code (see Tamper/Trouble Codes in section
6.6.6.) and a silent alarm (no bells/sirens)
"Audible alarm" enabled
Tamper/wiring failure will generate a trouble indicator (key [9]), a trouble report code (see Tamper/Trouble Codes in section
6.6.6.) and an audible alarm.
When the zone definition is "24 hour", the tamper definition follows the audible/silent alarm definition of the "24
hour" zone.
10.8
Tamper Bypass Options
Feature Select Programming D Address 090, key [6]
With this option enabled, the control panel will not generate an alarm if a tamper is detected on a bypassed zone while the
system is armed. With this option disabled, the control panel will generate an alarm if a tamper is detected on a bypassed zone
while the system is armed.
Key [6] "Off": Arm the system if Tamper on Bypassed Zone
Key [6] "On": Do not arm the system if Tamper on Bypassed Zone
[ENTER] + Installer Code + [10] [9] [10] + [6] On/Off + [ENTER]
10.9
Installer Test Mode
Key Access Programming D key [8]
The "Test Mode" will allow you to perform walk tests where the bell or siren will squawk, to indicate opened zones. To enter or exit
the control panel "Test Mode" press:
[ENTER] + Installer Code + [8] to enable; press [8] again to disable
10.10
Exclude Power Failure From Trouble Display
Feature Select Programming D Address 090, key [2nd]
Default: Disabled
Excludes the Power Failure, key [2], from the Trouble Display (see section 11.2).
10.11
Audible Trouble Warning
Feature Select Programming D Address 090, key [9]
Default: Disabled
Trouble conditions will emit an intermittent "beep" on the keypad. To silence the trouble warning, press the [TRBL] key.
10.12
Power Down Reset
Performing a power down reset will set the installer and master codes to factory default. Values entered at addresses 008-043,
062-124, 300-527, and all user codes will be erased ([2ND], [2ND]). Programmed values for all other addresses do not change. To
perform a reset, the installer lock must be disabled. To perform a power down reset perform the following:
1) Verify installer lock is disabled (see section 3.5)
2) Remove the battery and AC power from the control panel.
3) Set the reset jumper to on by placing a jumper on the reset pins of the control panel.
4) Re-connect the AC and battery power to the control panel.
5) Wait 10 seconds and remove the jumper.
Esprit 748+
39
Part 11: USER/KEYPAD FUNCTIONS
The innovative Esprit keypads take a new approach to security features and functions. Each numeral from 1 to 12 on the keypad
respectively represents each zone from 1 to 12 on the control panel. When the [2ND] key flashes, press the [2ND] key to view
zones 13 to 24, where keys [1] to [12] represent zones 13-24 respectively. When the zone light is "off", the status in the protected
zone is normal. If the zone light is "on", this means the zone is open. An LCD keypad will display the open zone numbers on the
screen.
The green "ready" indicator on the keypad will illuminate when the status of all the zones is normal (zones are closed). Therefore,
all protected windows and doors must be closed and motion detectors must not detect any movement except those zones that
have been bypassed.
Confirmation Beep: an intermittent series of beeps ("beep-beep-beep") indicates a successful keypad entry or system operation.
End/Rejection Beep: one long tone ("beeeeeeep") indicates incorrect keypad entry or unsuccessful system operation.
11.1
Programming Master & User Codes
The Esprit control panels have one Master (00) code and up to 48 User (01-48) codes. The default Master code is 474747.
The Master code can arm the system using any arming method, can create/modify user codes and can perform Key Access
Programming (see section 10.13). The User 1 code can create/modify access codes and perform key access programming. The
access code consists of either 4 or 6-digits and each digit can be any value from 0 to 9.
Note: do not enter [2nd] when programming the master code as this will invalidate the master code.
[ENTER] + Master or User 1 Code + 2-digit code number (00-48) + 4 or 6-digit access code + [ENTER]
11.2
Regular Arming
This method, commonly used for day-to-day arming, will arm all the zones in the system. To do so, the keypad's green "READY"
light must be illuminated, indicating that all zones are closed. All doors and windows must be closed, and there can be no
movement in areas monitored by motion detectors. Once the "READY" light is on, a valid user access code must be entered. If a
mistake is made entering the code or if the "READY" indicator is not on when the code was entered, the keypad will emit a
"rejection beep" (beeeeeeep).
When the correct user access code is entered, the keypad will emit a "confirmation beep" (beep-beep-beep) and the red "arm"
indicator will illuminate. The "READY" light will flash and the keypad will "beep" during the exit delay period (see section 8.7).
During the final 10 seconds of the exit delay, the keypad will "beep" and the "READY" indicator will flash at a faster rate. At the end
of the exit delay, the keypad will emit a "confirmation beep", the green "READY" indicator will extinguish and the red "arm"
indicator will remain illuminated to indicate that the system is armed.
11.2.1
One-Key Regular Arming
To use this feature, enable the "One-Key" Regular Arming option (see section 8.3). When the green "READY" light is on,
pressing and holding the [10] key for 2 seconds will arm all zones in the system. This feature can be used to allow
specific individuals like service personnel (i.e. cleaners, maintenance) to arm the system when leaving the protected
area, without giving them access to any other control panel operations. The use of a valid access code is still required
to disarm the system. For details on "Regular Arming", refer to section 11.2.
11.3
Away Arming
To rapidly arm the system without having to wait for the green "READY" indicator, simply press the [AWAY] key followed by a valid
access code. Once the exit delay expires, any open zones will be considered "deactivated" by the control panel. If while the
system is armed a "deactivated" zone is closed, the control panel will revert that zone to "active" status, generating an alarm if
breached.
If a mistake is made entering the code, the keypad will emit a "rejection beep" (beeeeeeep). When the correct user code is
entered, the keypad will emit a "confirmation beep" (beep-beep-beep) and the red "arm" indicator will illuminate. The "READY" light
and [AWAY] key will flash and the keypad will "beep" during the exit delay period (see section 8.7). During the final 10 seconds of
the exit delay, the keypad will "beep" and the "READY" indicator and [AWAY] key will flash at a faster rate. At the end of the exit
delay, the green "READY" indicator will stop flashing, the red "ARM" indicator will remain illuminated and the [AWAY] key will flash. If
programmed at address 518, the control panel will send a "partial arm" report code to the monitoring station. Note, to use this
method the user must have "away" arming priority, see Code Priority in section 8.12)
40 Reference & Installation Manual
11.4
Stay Arming
"Stay" arming allows the user to remain in the protected area while partially arming the system. This means that they can stay in
and move around the establishment, while certain designated zones are armed. For example, entry/exit points like doors or
windows, the basement, or perhaps all the zones on the perimeter of the establishment may be armed when going to sleep at
night, while the other zones remain deactivated. To program which zones will be activated when "stay arming" the system refer to
"System A"/Stay Zones in section 7.10.1. Also note that fire zones must be programmed as "stay zones"; they can not be
bypassed.
Unlike regular arming, the green "READY" indicator does not have to be illuminated. Only doors and windows programmed as
"stay zones" must be closed, and there can be no movement in areas monitored by motion detectors in "stay zones". To "stay"
arm the system, press the [STAY] key followed by a valid access code. If a mistake is made entering the code or if a "stay zone" is
open when entering the code, the keypad will emit a "rejection beep" (beeeeeeep). After entering the correct user access code,
the keypad will emit a "confirmation beep" (beep-beep-beep), the "ARM" indicator will illuminate and the green "READY" indicator
and [STAY] key will flash during the exit delay period. During the final 10 sec. of the exit delay, the "READY" indicator and [STAY] key
will flash at a faster rate. At the end of the exit delay, the keypad will emit a "confirmation beep", the "READY" indicator will stop
flashing, the "ARM" indicator will remain illuminated and the [STAY] key will flash. Note, to use this method the user must be given
"stay" arming priority, see Code Priority in section 8.12.
11.4.1
One-Key Stay Arming
To use this feature, enable the "One-Key" Stay/"System A" Arming option (see section 8.4). When all "stay zones" are
closed, pressing and holding the [STAY] key for 2 seconds will arm only zones programmed as "stay zones". For details
on "Stay Arming", refer to section 10.4.
11.4.2
One-Key Double Stay Arming
During the "stay" arming exit delay (see section 11.4), press and hold the [stay] key for 2 seconds until you hear a
single "beep". This will switch all "entry delay" zones to "instant" zones (see sections 7.6, 7.8 and 7.9). Therefore, any
entry delay zone that is breached will immediately generate an alarm instead of waiting a pre-determined period.
11.4.3
Fast Exit
This feature is only available when the system is "Stay" armed (see section 11.4). This feature will allow the user to exit
premises while the system is already armed and keep the system armed. This can be done one of two ways:
With the system already "stay" armed (after its exit delay), press and hold the [STAY] key for 2 seconds. The system will
switch to exit delay mode (green "READY" indicator flashes), allowing time for the user to exit the premises. At the end
of the exit delay period, the system will return to "stay" arm mode.
With the system already "stay" armed, press and hold the [10] key for 2 seconds. The system will switch to exit delay
mode (green "READY" indicator flashes). At the end of the exit delay period, the system will "regular" arm the system
(see section 11.2).
11.5
Arming/Disarming Partitions
Thanks to the partitioning feature, two distinct systems (A and B) can be created and controlled by the control panel. Partitioning
can be used in installations where shared security systems are more practical, such as office/warehouse buildings, or apartment/
condominium complexes. Each zone can be assigned to System A, System B, both systems or given no system assignment.
User access codes can also be programmed to arm/disarm one system or both systems simultaneously (see Code Priority in
section 8.12). Unlike regular arming, the green "READY" indicator does not have to be illuminated. All doors and windows
pertaining to the desired system must be closed, and there can be no movement in areas monitored by motion detectors in the
desired system.
1) If a user is not given any code priorities, the user can not arm or disarm a partitioned system.
2) If a user is given code priority to one of the two systems, entering the correct access code will arm or disarm the system to
which the user was given priority.
3) If a user is given code priority to arm/disarm both systems A & B, it will function as follows:
• If the User enters the correct access code when systems "A" and "B" are disarmed, it will completely arm both systems.
• If the User enters the correct access code when systems "A" and "B" are armed, it will completely disarm both systems.
• When the system is partially armed, (i.e. only “System A" or only “System B" is armed) entering the correct access code will
arm the other system.
• To arm/disarm each system separately, do the following:
Press [STAY] + [VALID ACCESS CODE] to arm/disarm "System A".
Press [AWAY] + [VALID ACCESS CODE] to arm/disarm "System B".
Esprit 748+
41
If a mistake is made entering the code or if a zone in the desired system is open when entering the code, the keypad will emit a
"rejection beep" (beeeeeeep). When the access code is correctly entered, the keypad will emit a "confirmation beep" (beep-beepbeep). The keypad can display the status of both systems. When "System A" is armed, the [STAY] key and "ARM" indicator will
remain on. If System B is armed, the "AWAY" key and "ARM" indicator will remain on. When both systems are armed, all three
lights will remain on.
11.5.1
One-Key System A Arming
This feature allows the user to arm "System A" without the use of an access code. To use this feature, enable the
"One-Key" Stay/"System A" Arming option (see section 7.4). When all the zones in "System A" are closed, press and
hold the [stay] key for 2 seconds to arm "System A". This feature can be used to allow specific individuals like service
personnel (i.e. cleaners, maintenance) to arm the system when leaving the protected area, without giving them access
to any other control panel operations. For details on "System A" Arming refer to section 11.5.
11.6
System Disarming
The user must enter the protected area through a designated entry/exit point. The keypad will "beep" during the entry delay
reminding the user to disarm the system. Upon entry of a valid access code, the red "ARM" indicator will extinguish and the
keypad will emit a confirmation "beep" (beep-beep-beep) denoting the system has been disarmed. If an incorrect access code is
entered, the keypad will emit a rejection "beep" (beeeeeeeep). Press the [CLEAR] key at any time to clear data and re-enter
another access code. If an alarm was generated from a fire or 24-hour zone while the system was armed, entering a valid user
code will silence the siren. However, you should then check the zone and eliminate the cause of the alarm. If you are unable to
pinpoint the reason for the alarm, call your installer.
11.7
Alarm Memory
If an alarm condition occurs when the system is armed, the [MEM] key will turn on. A record of all alarm situations that occur is
stored in memory. After disarming the system, pressing once on the [MEM] key will display which zones were open during the
alarm period by illuminating the corresponding zone indicator(s) or by displaying it on the LCD screen depending on the type of
keypad used. Please note if the [MEM] key is pressed again when using LED keypads (636 and 646) you will enter the event
display which can only be decoded with a 642 LCD keypad. To exit the alarm memory display, press the [CLEAR] key. If using a
642 LCD keypad press the [MEM] key followed by the [INFO] key and use the up and down keys to scroll through the event list in
memory. The alarms will remain in memory until the system is armed and disarmed without generating an alarm.
11.8
Keyswitch or Pushbutton Arming/Disarming
A keyswitch or push button can be used to "Stay" (section 11.4) or "Regular" (section 11.2) arm/disarm the system. If the system
is ready and the button is pressed, the system will arm. Pressing the button again will disarm the system. If a "Stay" armed
system is in entry delay or if an alarm has been generated while "Stay" armed, the keyswitch or push button can not be used to
disarm the system. In this case, only a keypad can disarm the system. In a partitioned system the keyswitch or push button will
arm/disarm "System A" regardless of the "System B" status. To enable this feature and set the options (stay or regular arming)
refer to Arming Using Keyswitch in section 8.5.
11.9
Manual Zone Bypassing
When a zone is bypassed it will no longer be monitored by the control panel, hence, will not generate an alarm. A user may wish
to bypass certain zones when, for example, workers are renovating part of the establishment or if a component in the system is
damaged. Manual bypass arming instructs the control panel to ignore ("deactivate") specified zones in order to arm the
remainder of the system. Verify that the following options are set in the control panel so that a user can manually bypass zones:
• You must first define which zones are Bypass Enabled Zones (see section 7.11). Zones not identified as Bypass Enabled can
not be bypassed.
• Only users with the appropriate Code Priority (see section 8.12) can bypass zones.
• Please note, the control panel can not bypass fire zones.
To bypass zones, press the [BYP] key followed by a valid access code. If the wrong code was entered or a code without bypass
priority, the keypad will emit a "rejection beep" (beeeeeeep). If the correct code is entered, the [BYP] key will flash to indicate that
you are now in "bypass mode". If there are any currently bypassed zones, their respective zone indicators will turn on. Press the
key corresponding to the zone you wish to bypass until their respective zone indicator turns on. If the zone you wish to bypass
has not been programmed as "bypass enabled", the corresponding zone indicator will never turn on. Press the [CLEAR] key to
erase the current zone bypass entries and exit the "bypass mode". If you have entered the correct bypass entries, press the
[ENTER] key to accept these entries. The [BYP] key will remain on, denoting that zones in the system are currently bypassed,
hence, the next time the system is armed, certain zones will be bypassed. When the system is disarmed, the bypass entries will
be erased.
42 Reference & Installation Manual
11.10
Bypass Recall
This feature permits users to reinstate the last zone bypass entries saved in memory. When the system is disarmed, the bypass
entries will be erased. By using the "bypass recall" feature, you can reinstate the previous bypass entries saved in memory. While
in the "bypass mode", press the [BYP] + [ENTER] keys and the previous bypass status will be re-established. This eliminates the
need to re-enter the bypass entries every time the system is armed. If a user is in the process of entering new bypass entries on
the keypad, pressing the [BYP] key will override new information and reinstate previous bypass entries.
11.11
Keypad Chime Zones
A chimed zone "advises" you when a zone is opened by creating a rapid intermittent beep tone (beep-beep-beep-beep-beep). Up
to six zones plus the local keypad zone can be programmed as chime zones. To turn on the "chime zone" feature, press and hold
the key corresponding to the desired zone ([1] to [6]) for three seconds until the intermittent chime beep is heard. This means that
the chime feature has been activated. If a continuous beep is heard, this means that the chime beep has been deactivated. To
enable the chime feature on the keypad zone, press and hold the [8] key for three seconds. To mute the keypad's alarm sounder,
press and hold the [9] key for three seconds until the intermittent chime beep is heard. This means that the muting feature has
been activated. If a continuous beep is heard, this means that the muting feature has been deactivated. If there is more than one
keypad in the system, please "chime" program each keypad separately. Keypad chimes must be reprogrammed if the panel
suffers a total power loss.
Key [1]-[6]: Turns chime "on" or "off" in zones numbered 1-6
Key [8]:
Turns chime "on" and "off" for the local keypad zone
Key [9]:
Turns the keypad's alarm sounder muting "on" or "off"
11.12
Trouble Display Monitoring
Trouble conditions are continuously monitored by the control panel, which recognizes and displays 10 different trouble conditions
on the keypad. When a trouble condition occurs, the [TRBL] key will illuminate and the keypad will emit an intermittent beep if the
Audible Trouble Warning (see section 10.11) is enabled. Press the [TRBL] key to switch to "trouble display" mode. The [TRBL] key
will flash and any illuminated keys correspond to a current trouble condition as described below. Press any key to exit the "trouble
display" mode.
11.12.1 No Battery/Low Battery - Key [1]
The control panel conducts a dynamic battery test under load every 60 seconds. The illumination of the [1] key indicates that the
back-up battery is disconnected or that the battery should be replaced, as it will not provide adequate back-up current in case of
AC loss. If the control panel is currently running on battery power, the illumination of the [1] key indicates that the battery voltage
has dropped to 10.5 volts or lower.
11.12.2 Power Failure - Key [2]
The control panel conducts a dynamic battery test under load every 60 seconds. The control panel will detect a power loss if a
continuous loss of AC (≤12.5V) has occurred during the period between two AC power tests (64 to 116 seconds). If a power loss
remains present throughout the Power Failure Report Delay (see section 6.9), the panel will transmit the report code
programmed at address 507 and the [TRBL] key will flash rapidly indicating a power failure. The trouble indicator is restored if AC
is detected during the dynamic battery test. You can remove the power failure trouble indicator from the trouble display by
enabling the Exclude Power Failure From Trouble Display option (see section 10.10).
11.12.3 Bell Disconnected - Key [4]
The illumination of the [4] key indicates that there is no bell or siren connected to the bell output terminals of the panel.
Please note that when connecting a bell or siren to an optional relay output the trouble indicator will always be on. To
avoid this, connect a 1KW resistor across the bell output. The control panel only recognizes bells or siren connected
directly to the bell output of the control panel not those connected through a relay.
11.12.4 Maximum Bell current - Key [5]
The bell output is microprocessor controlled and will automatically shutdown when the current exceeds 3A. If this
occurs, the [5] key will illuminate. After opening the short or reducing the load, the bell current is restored upon the
following alarm generation.
This trouble indicator will only appear when the bell is activated (i.e. during an alarm)
Esprit 748+
43
11.12.5 Maximum Auxiliary Current - Key [6]
The illumination of the [6] key indicates that the auxiliary current has exceeded 1A. This will cause automatic shutdown
of the auxiliary output. After opening the short or reducing the load, the panel will restore power to the auxiliary output
following the dynamic battery test (approximately 60 seconds).
11.12.6 Communicator Report Failure - Key [7]
If the control panel was unsuccessful when attempting to communicate with the monitoring station computer or the
Espload software the [7] key will illuminate.
11.12.7 Timer Loss - Key [8]
The illumination of the [8] key indicates that the control panel’s internal clock must be re-programmed. To re-program
the timer press:
[ENTER] + (Installer, Master or User 1 Code) + [MEM] + 2 digits (00 to 23) representing hours + 2 digits (00 to 59)
representing minutes + [ENTER]
11.12.8 Tamper/Zone Wiring Failure - Key [9]
If the Tamper/Wire Fault Recognition Options (see section 10.7) are enabled, the [9] key will illuminate to indicate a
short or cut on a zone input. In order to provide line short recognition the zone connections must have EOL resistors
(see Zone Input Terminal Connections sections 2.8 to 2.10).
11.12.9 Telephone Line Monitoring - Key [10]
If the Telephone Line Monitoring (TLM) feature (see section 10.1) is enabled, the [10] key will illuminate to indicate
that the control panel has not detected the presence of a telephone line for 30 seconds.
11.12.10 Fire Trouble - Key [11]
The illumination of the [11] key indicates a tamper on zone 3, if identified as a fire zone (see "24 Hour" & Fire Zones in
section 7.5).
11.13
Key Access Programming
This method allows for quick programming of features without entering addresses or section numbers. The following features are
programmed using the installer code as well as the master code and user 1 codes.
•
•
•
•
•
•
•
Auto Arm Time: for details see section 8.1.1
Panel Time: for details see section 10.5
Manual Test Report: for details see section 6.8
Call Espload: for details see section 5.5
Answer Espload: for details see section 5.6
Cancel Communication: for details see section 5.7
Installer Test Mode: for details see section 10.9
44 Reference & Installation Manual
Warnings
Important Information
This equipment complies with Part 68 of the FCC rules subpart D and CS03. Inside the cover of this equipment is a label that contains, among other
information, the FCC registration number of this equipment.
Notification to Telephone Company
Upon request, customer shall notify telephone company of particular line to
which the connection will be made, and provide the FCC registration
number and the ringer equivalence of the protective circuit.
FCC Registration Number: 5A7AL01B728ULT
Ringer Equivalence Number: 0.1B (U.S. & Canada)
USOC Jack:
RJ31X (USA), CA31A (CANADA)
Telephone Connection Requirements
Except for telephone company provided ringers, all connections to the
telephone network shall be made through standard plugs and telephone
company provided jacks, or equivalent, in such a manner as to allow for
easy, immediate disconnection of terminal equipment. Standard jacks shall
be so arranged that, if plug connected thereto is withdrawn, no interference
to operation of equipment at customer's premises which remains connected
to telephone network shall occur by reason of such withdrawal.
Incidence of Harm
Should terminal equipment/protective circuitry cause harm to telephone
network, telephone company shall, where practicable, notify customer that
temporary disconnection of service may be required; however, where prior
notice is not practicable, the telephone company may temporarily
discontinue service if action is deemed reasonable in circumstances. In
case of temporary discontinuance, telephone company shall promptly notify
customer and will be given opportunity to correct the situation.
Changes in Telephone Company Equipment or Facilities
The telephone company may make changes in its communication facilities,
equipment operations or procedures, where such actions are reasonably
required and proper in its business. Should any such changes render
customer's terminal equipment incompatible with the telephone company
facilities, the customer shall be given adequate notice to effect the
modifications to maintain uninterrupted service.
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
equipment intermittently, the user is encouraged to try to correct the
interference by one or more of the following measures: (1) re orient or
relocate the receiving antenna; (2) increase the separation between the
equipment and receiver; (3) connect the equipment to an outlet on a circuit
other than the one to which the receiver is connected, or (4) consult the
dealer or an experienced radio/tv technician for assistance.
Caution:
Changes or modifications not expressly approved by PARADOX
SECURITY SYSTEMS could void the user's authority to operate the
equipment.
Warranty
Paradox Security Systems Ltd. (“Seller”) warrants its products to be free
from defects in materials and workmanship under normal use for a period of
one year. Except as specifically stated herein, all express or implied
warranties whatsoever, statutory or otherwise, including without limitation,
any implied warranty of merchantability and fitness for a particular purpose,
are expressly excluded. Because Seller does not install or connect the
products and because the products may be used in conjunction with
products not manufactured by Seller, Seller cannot guarantee the
performance of the security system and shall not be responsible for
circumstances resulting from the product’s inability to operate. Seller
obligation and liability under this warranty is expressly limited to repairing or
replacing, at Seller's option, any product not meeting the specifications.
Returns must include proof of purchase and be within the warranty period.
In no event shall the Seller be liable to the buyer or any other person for any
loss or damages whether direct or indirect or consequential or incidental,
including without limitation, any damages for lost profits stolen goods, or
claims by any other party, caused by defective goods or otherwise arising
from the improper, incorrect or otherwise faulty installation or use of the
merchandise sold.
Notwithstanding the preceding paragraph, the Seller’s maximum liability will
be strictly limited to the purchase price of the defective product. Your use of
this product signifies your acceptance of this warranty.
General
BEWARE: Dealers, installers and/or others selling the product are not
authorized to modify this warranty or make additional warranties that are
binding on the Seller.
This equipment shall not be used on coin telephone lines. Connection to
party line service is subject to state tariffs.
Attachment Limitation Notice
Ringer Equivalence Number (REN)
The ren is useful to determine the quantity of devices that you may connect
to your telephone line and still have all of those devices ring when your
telephone number is called. In most, but not all areas, sum of the ren's of
all devices connected to one line should not exceed five (5.0). To be certain
of the number of devices that you may connect to your line, you may want
to contact your local telephone company.
Equipment Maintenance Facility
If you experience trouble with this telephone equipment, please contact
facility indicated below for information on obtaining service or repairs. The
telephone company may ask that you disconnect this equipment from
network until problem is corrected or until you are sure that the equipment
is not malfunctioning.
FCC Part 15, Warnings
Information to User
This equipment has been tested and found to comply with the limits for
Class B digital devices, pursuant to Part 15 of FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy, and, if not installed and used in accordance with
The Industry Canada label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network
protective, operational and safety requirements. The Department does not
guarantee the equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is permissible
to be connected to the facilities of the local telecommunications company.
The equipment must also be installed using an acceptable method of
connection. The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may give
the telecommunications company cause to request the user to disconnect
the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic water
pipe system, if present, are connected together. This precaution may be
particularly important in rural areas.
CAUTION: Users should not attempt to make such connections
themselves, but should contact the appropriate electrical inspection
Esprit 748+
45
authority, or electrician, as appropriate.
The Load Number (LN) assigned to each terminal device denotes the
percentage of the total load to be connected to a telephone loop which is
used by the device, to prevent overloading. The termination on a loop may
consist of any combination of devices subject only to the requirement that
the total of the Load Numbers of all of the devices does not exceed 100.
terminal. The Class 2 or power-limited fire alarm circuits shall be installed
using CL3, CL3R, CL3P or substitute cable permitted by the National
Electrical Code, ANSI/NFPA 70.
Requirements and Guidelines for AUSTEL Installations
Industry Canada certification is only applicable to installation of devices
which include transformers approved by the Canadian Standards
Association (CSA).
Austel-approved installations: use a transformer approved by the State
Electricity commission, such as "Dyen" PA series 15Vac 22VA. With this
transformer, do not exceed the following maximum currents:
- maximum Auxiliary current (including keypads): 300mA
- maximum Bell current: 600mA
Requirements and Guidelines for UL Installations
Requirements and Guidelines for cUL Installations
UL has only evaluated the 728ULT for compatibility with the Ademco model
685, FBI model CP220FB, SUR-GUARD SG-MLR2-D6 and Silent Knight
model 9000.
When the system controls a fire alarm system, wiring method must
correspond to section 32 of the Canadian Electrical Code.
UL listed in accordance with standard UL1023 (Household Burglar - Alarm
System Units), standard UL985 (Household Fire Warning Units) and
UL1635 (Digital Alarm Communicator System Units). Look for the UL mark
on the product. Only products bearing this mark are UL listed.
Some operational features are not permitted in UL installations. To respect
the standards for household applications, the installer should follow these
guidelines when configuring the system.
1. All components of the system should be UL listed for the intended
application.
2. If the installation is a FIRE ALARM application, refer to NFPA Standard
74 for details on smoke detector locations. There must be at least one
UL-Listed Indoor Fire Alarm Warning Signalling Appliance.
3. For UL/cUL Burglar Applications:
Maximum entry time = UL 45 seconds/cUL 60 seconds
Maximum exit time = UL 60 seconds/cUL 120 seconds
Minimum bell cutoff time = 5 minutes
4. Keypad Models 639, 642 and 646 are not UL/cUL listed. Do not use the
708 or Esprit with a UL installation--they are not UL listed.
5. The upload/download software should not be used on UL listed systems.
6. All outputs are Class 2 or power-limited, except for the battery terminal.
The Class 2 and power-limited fire alarm circuits shall be installed using
CL3, CL3R, CL3P or substitute cable permitted by the National Electrical
Code, ANSI/NFPA 70.
Label: US: 5A7AL01B728ULT
Filing Type: New Filing
Product Identifier: 728ULT
Equipment Code: AL
Network Address Signal Code: E
Country of Origin: CANADA (CAN)
AC Ringer Equivalent Number: 01B
USOC Jacks: RJ31X
Equipment Description: Control panel for residential burglar and fire
warning systems
Rechargeable Acid/Lead or Gel Cell Backup Battery: 12Vdc, 4Ah/7Ah; UL/
cUL: 12Vdc, 7Ah only
Transformer: Universal, Model No. UB1640W, 16.5Vac (50-60Hz) 20VA
minimum (40VA recommended). Do not connect the transformer to a
switch-controlled outlet.
Bell/Siren: UL/cUL Wheelock 46T-12
Aux Power: 450mA (fuseless shutdown at 650mA); UL: 200mA maximum
for 24Hr stand-by
Smoke Detector: 2-wire Hochicki model SLR 835BH-2 (see page 10 for
more information)
Warning: For UL installations, the metallic enclosure must be grounded to
the cold water pipe or to the grounding rod.
UL/cUL: All outputs are Class 2 or power-limited, except for the battery
46 Reference & Installation Manual
Look for the cUL mark on the product. Only products bearing this mark are
cUL listed.738 Ultra is not UL listed.
Rechargeable Acid/Lead or Gel Cell Backup Battery: 12Vdc, 4Ah/7Ah; UL/
cUL: 12Vdc, 7Ah only
Transformer: Universal, Model No. UB1640W, 16.5Vac (50-60Hz) 20VA
minimum (40VA recommended). Do not connect the transformer to a
switch-controlled outlet.
Bell/Siren: UL/cUL Wheelock 46T-12
Aux Power: 450mA (fuseless shutdown at 650mA); UL: 200mA maximum
for 24Hr stand-by
Smoke Detector: 2-wire Hochicki model SLR 835BH-2 (see page 10 for
more information)
© 2003-2005 Paradox Security Systems Ltd. Esprit and Ultra are
trademarks or registered trademarks of Paradox Security Systems Ltd. and
its affiliates in Canada, the United States and other countries. All rights
reserved. Specifications may change without prior notice. One or more of
the following patents may apply: 6215399, 6111256, 5751803, 5721542,
5287111, 5119069, 5077549, 5920259 5886632. Canadian and
international patents may also apply
FCC WARNINGS
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC rules. Inside the cover of
this equipment is a label that contains, among other information, the FCC
registration number of this equipment.
NOTIFICATION TO TELEPHONE COMPANY
Upon request, customer shall notify telephone company of particular line to
which the connection will be made, and provide the FCC registration
number and the ringer equivalence of the protective circuit.
GENERAL
This equipment shall not be used on coin telephone lines. Connection to
party line service is subject to state tariffs.
RINGER EQUIVALENCE NUMBER (REN)
The ren is useful to determine the quantity of devices that you may connect
to your telephone line and still have all of those devices ring when your
telephone number is called. In most, but not all areas, sum of the ren's of
all devices connected to one line should not exceed five (5.0). To be certain
of the number of devices that you may connect to your line, you may want
to contact your local telephone company.
EQUIPMENT MAINTENANCE FACILITY
If you experience trouble with this telephone equipment, please contact
facility indicated below for information on obtaining service or repairs. The
telephone company may ask that you disconnect this equipment from
network until problem is corrected or until you are sure that the equipment
is not malfunctioning.
FCC PART 15, WARNINGS
INFORMATION TO USER
This equipment has been tested and found to comply with the limits for
Class B digital devices, pursuant to Part 15 of FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy, and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
equipment intermittently, the user is encouraged to try to correct the
interference by one or more of the following measures: (1) reorient or
relocate the receiving antenna; (2) increase the separation between the
equipment and receiver; (3) connect the equipment to an outlet on a circuit
other than the one to which the receiver is connected, or (4) consult the
dealer or an experienced radio/tv technician for assistance.
CAUTION:
Changes or modifications not expressly approved by PARADOX
SECURITY SYSTEMS could void the user's authority to operate the
equipment
CAUTION: Users should not attempt to make such connections
themselves, but should contact the appropriate electrical inspection
authority, or electrician, as appropriate.
The Load Number (LN) assigned to each terminal device denotes the
percentage of the total load to be connected to a telephone loop which is
used by the device, to prevent overloading. The termination on a loop may
consist of any combination of devices subject only to the requirement that
the total of the Load Numbers of all of the devices does not exceed 100.
The Load Number of this unit is 33.
Industry Canada certification is only applicable to installation of devices
which include transformers approved by the Canadian Standards
Association (CSA).
Esprit 748+
47
Notes
48 Reference & Installation Manual
Esprit 748+
49
For technical support in Canada or the U.S., call 1-800-791-1919 for English or 1-866-912-0600 for French, Monday to Friday from
8:00 a.m. to 8:00 p.m. EST. For technical support outside Canada and the U.S. call 00-1-450-491-7444, Monday to Friday from
8:00 a.m. to 8:00 p.m. EST. Please feel free to visit our website at www.paradox.ca.
780 Industriel Blvd., Saint-Eustache (Quebec) J7R 5V3 CANADA
Tel.: (450) 491-7444
Fax: (450) 491-2313
www.paradox.ca
PRINTED IN CANADA 01/06
748P-EI02