Crestron | iMedia IM-RX3 | Installation guide | Crestron iMedia IM-RX3 Installation guide

Crestron iMedia IM-RX3 Installation guide
Crestron IM-WCC
iMedia Wall Mount Computer Center
Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2005 Crestron Electronics, Inc.
Crestron IM-WCC
iMedia Wall Mount Computer Center
Contents
iMedia Wall Mount Computer Center: IM-WCC
1
Introduction ..........................................................................................................1
Features and Functions...........................................................................1
The iMedia System ................................................................................1
Specifications .........................................................................................3
Physical Description...............................................................................4
Industry Compliance ..............................................................................7
Setup.....................................................................................................................7
Network Wiring .....................................................................................7
Installation..............................................................................................7
Hardware Hookup ..................................................................................8
System Configuration.............................................................................9
Problem Solving .................................................................................................10
Troubleshooting ...................................................................................10
Further Inquiries...................................................................................10
Future Updates .....................................................................................10
Return and Warranty Policies.............................................................................11
Merchandise Returns / Repair Service .................................................11
CRESTRON Limited Warranty ...........................................................11
Operations & Installation Guide – DOC. 6382
Contents • i
Crestron IM-WCC
iMedia Wall Mount Computer Center
iMedia Wall Mount Computer
Center: IM-WCC
Introduction
Features and Functions
The IM-WCC is part of the Crestron iMedia line of network devices, room
control systems and signal routing solutions. The iMedia devices currently
include two receivers, IM-RX1 and IM-RX3, and three transmitters, IM-WCC,
IM-TCC, and IM-FTCC-B.
The iMedia Wall Mount Computer Center supports a single computer video and
audio connection in a standard double gang electrical box.
This device uses iMedia (IM) technology utilizing a single CresCAT-IM cable
to transmit computer RGB and stereo audio signals to a single projector or
plasma display. A typical XGA signal (1024 X 768 pixels at 60Hz) can be
transmitted up to 84 feet using iMedia, while higher resolutions up to
1600 x 1200 can be handled over shorter distances. Audio is transmitted
digitally at 20-bit, 48 kHz resolution. To facilitate connection of audio, video,
and computer equipment, all media, power and control signals are routed via a
single CresCAT-IM cable for an uncomplicated installation.
NOTE: The IM-WCC is not a Cresnet® device.
Functional Summary
•
One computer RGB input connector
•
One computer audio input connector
•
One iMedia RJ-45 output connector (on the rear side)
•
Power on/off SELECT button and indicator
•
Rotary local volume control
The iMedia System
Using a new, proprietary signal routing solution, RGBHV, audio, power and
control signals are all transported using a single cable solution called iMedia.
Operations & Installation Guide – DOC. 6382
iMedia Wall Mount Computer Center: IM-WCC • 1
iMedia Wall Mount Computer Center
Crestron IM-WCC
The iMedia transport system port is capable of managing computer RGB and
audio signals simultaneously through one CresCAT-IM cable, simplifying
installations.
Routing CresCAT-IM cable is less expensive and much simpler than routing
multi-colored, multi-conductor coax cable. All Crestron products using the
iMedia transport system are capable of sending and receiving iMedia signals via
CresCAT-IM cable. Installation of any iMedia device is as simple as installing
one iMedia cable from output to input. Installations are flexible, affordable, and
fast.
Up to three iMedia transmitters can be installed in an iMedia system. Pressing
the SELECT button on any iMedia transmitter makes that input active,
overriding the previously selected input. Holding the SELECT button for five
seconds powers down the system.
The pin assignment is based on the EIA/TIA 568B RJ-45 Jack standard.
Power is supplied to the IM transmitters via the audio circuit.
To determine which pin is number 1, hold the cable so that the end of the eight
pin modular jack is facing you, with clip down and copper side up. When
looking down at the copper connections, pin 1 is on the far right.
iMedia Pin Assignment
RJ-45 Male Connector
RJ-45
Pin
Number
Wire Colors
iMedia
Assignment
RGB and Audio
1
White/Orange
- RGB Red
2
Orange
+ RGB Red
3
White/Green
- RGB Green
4
Blue
+ Audio/Power
5
White/Blue
- Audio/Power
6
Green
+ RGB Green
7
White/Brown
- RGB Blue
8
Brown
+ RGB Blue
NOTE: Power is supplied to pins 4 and 5 from the IM-RX1 or IM-RX3.
Signal Selection
The VGA signal connected to the IM transmitter is delivered to the display
device (e.g., projector) via the RGBHV output of an IM receiver (IM-RX1 or
IM-RX3). Each IM transmitter possesses a SELECT button, which activates that
input. The receiver automatically routes the last activated input to the RGB
output and deactivates any prior selection. In addition, the display's power and
input selection commands can be controlled via the IR or COM port.
Video Resolution and Cable Length
The receiver can accomplish frequency compensation on each input to achieve
correct operation. This compensation scheme is effective for CresCAT-IM
cables as long as the maximum skew of 15 ns per 100 m is not exceeded.
2 • iMedia Wall Mount Computer Center: IM-WCC
Operations & Installation Guide - DOC. 6382
Crestron IM-WCC
iMedia Wall Mount Computer Center
Maximum Resolution and Cable Length
RESOLUTION
REFRESH
RATE
(HZ)
PIXEL
RATE
(MHZ)
VGA
60
25.18
39.7
218.5
(640 X 480)
72
31.50
31.7
174.6
85
36.00
27.8
152.8
SVGA
56
36.00
27.8
152.8
(800 X 600)
72
50.00
20.0
110.0
85
56.25
17.8
97.8
XGA
60
65.00
15.4
84.6
(1024 X 768)
70
75.00
13.3
73.3
85
94.50
10.6
58.2
SXGA
60
108.00
9.3
50.9
(1280 X 1024)
75
135.00
7.4
40.7
85
157.50
6.3
34.9
UXGA
60
162.00
6.2
34.0
(1600 X 1200)
70
189.00
5.3
29.1
85
229.50
4.4
24.0
PIXEL
TIME
(NS)
MAX
LENGTH
(FEET)
Specifications
Specifications for the IM-WCC are given in the following table.
IM-WCC Specifications
SPECIFICATION
DETAILS
Connectors
Computer Input
(1) DB15HD Female
Computer Audio
(1) 3.5mm Mini-Jack, Computer Soundcard
Type
iMedia Output
(1) RJ-45 CAT5E/CAT6
Ground
(1) Flying Ground Lead
Video Formats
RGBHV (VGA), RGBS, RGsB
RGB Video
R/G/B: 0 dB (Unity gain, 75 Ω termination), for
1.0 V p-p max input. Input Impedance 75 Ohms.
Gain / Bandwidth
Supports videos up to XGA @ 60 Hz vertical
rate with maximum cable length of 84 feet and
maximum compensation at receiver. For higher
pixel resolutions (up to 1600 X 1200 pixels at 60
Hz vertical rate) refer to the chart on page 3.
H and V Sync
5 V p-p max into 1 K Ohm
Computer Associated Audio
Max. Line level input
2 V RMS
Input Impedance
10 K Ohm
Level / Bandwidth
Audio Bandwidth 20 Hz to 20 KHz
Audio Analog/Digital
conversion
20-bit, 48 kHz
Frequency Response
20 Hz to 20 kHz
Continued on the following page
Operations & Installation Guide – DOC. 6382
iMedia Wall Mount Computer Center: IM-WCC • 3
iMedia Wall Mount Computer Center
Crestron IM-WCC
IM-WCC Specifications (continued)
SPECIFICATION
DETAILS
Operating Temperature and
Humidity
41º to 104º F (5º to 40º C)
10 to 90% relative humidity
(non-condensing)
Dimensions and Weight
Width: 4.56 in (11.59 cm)
Height: 4.50 in (11.43 cm)
Depth: 2.81 in (7.13 cm)
Weight: 0.85 lbs (0.39 kg)
Physical Description
The IM-WCC is a mountable plate with electronic components attached to the
rear side. The front side of the plate is labeled and includes; one SELECT
button, one VOLUME control, one COMPUTER DB15HD female connector
and one AUDIO mini-jack connector. Refer to the following physical
dimensions.
IM-WCC Front View
4 • iMedia Wall Mount Computer Center: IM-WCC
Operations & Installation Guide - DOC. 6382
Crestron IM-WCC
iMedia Wall Mount Computer Center
Physical Dimensions - Front View
SideView
Operations & Installation Guide – DOC. 6382
Top View
Back View
iMedia Wall Mount Computer Center: IM-WCC • 5
iMedia Wall Mount Computer Center
Crestron IM-WCC
Controls
Select Button
The IM-WCC has one momentary select button and a power on/selected green
LED indicator. Press to turn on the system and select this transmitter as the input
to the iMedia receiver (IM-RX1 or IM-RX3). Press and hold for five seconds to
power down the system. The LED blinks while powering down. When the LED
stops blinking and the button is released, the unit powers down.
Volume Control
The IM-WCC has a rotary local volume control. Adjusting this knob sets the
audio level for the local input.
Ports
COMPUTER
This female DB15HD connector is used for connecting a computer’s RGB
video output to the display device. A corresponding 3.5mm mini-jack is
provided for the computer sound card output.
•
Maximum input voltage 1.0 Vp-p (R/G/B), 5.0 Vp-p (H/V)
•
Input Impedance 75 Ohms (R/G/B), 1 k Ohms (H/V)
Refer to the following table for pin-assignments.
RGB DB15HD Pin Assignments
PIN
FUNCTION
PIN
FUNCTION
1
Red Video
9
No Connect
2
Green Video
10
Ground
3
Blue Video
11
No Connect
4
Reserved
12
Monitor Sense 1
5
Ground
13
Horizontal Sync
6
Red Ground
14
Vertical Sync
7
Green Ground
15
Monitor Sense 2
8
Blue Ground
AUDIO
The 3.5 mm computer audio connector provides an unbalanced stereo line-level
audio input.
•
Maximum input level 2 VRMS
•
Input impedance 10 kΩ
6 • iMedia Wall Mount Computer Center: IM-WCC
Operations & Installation Guide - DOC. 6382
Crestron IM-WCC
iMedia Wall Mount Computer Center
IM
1
This unlabeled eight-pin RJ-45 transport port on the rear side of the IM-WCC
allows connection of the iMedia cable. It carries audio and video signals over
CresCAT-IM cable to an iMedia receiver (IM-RX1 or IM-RX3). For more
information on iMedia cable length refer to the chart on page 3.
NOTE: Always use CresCAT-IM cable to make iMedia connections.
Industry Compliance
As of the date of manufacture, the IM-WCC has been tested and found to
comply with specifications for CE marking and standards per EMC and
Radiocommunications Compliance Labelling.
NOTE: This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Setup
Network Wiring
CAUTION: In order to ensure optimum performance over the full range of
your installation topology, Crestron Certified Wire, and only Crestron Certified
Wire, should be used. Failure to do so, may incur additional charges if support is
required to identify performance deficiencies as a result of using improper wire.
CAUTION: Use only Crestron power supplies for Crestron equipment. Failure
to do so could cause equipment damage or void the Crestron warranty.
Installation
The IM-WCC is designed to mount in a standard 2.5-inch (6.35 cm) deep,
double-gang, electrical box.
Tools Required
•
Phillips screwdriver
•
Small flat-blade screwdriver (for connecting the VGA cable)
Mounting Parts Supplied with the IM-WCC
PART DESCRIPTION
Screw #6-32 x 1 in, Pan Head, Phillips
Operations & Installation Guide – DOC. 6382
QUANTITY
4
iMedia Wall Mount Computer Center: IM-WCC • 7
iMedia Wall Mount Computer Center
Crestron IM-WCC
Installation in a 2-Gang Electrical Box
Hardware Hookup
Refer to the following hookup diagram and, aside from attaching power last,
complete the connections in any order.
NOTE: To prevent overheating, do not operate this product in an area that
exceeds the environmental temperature range listed in the specifications table.
Consideration must be given if installed in a closed or multi-unit rack assembly,
inside a closed desk, or in a closed podium since the operating ambient
temperature of these environments may be greater than the room ambient.
Contact with thermal insulating materials should be avoided on all sides of the
unit.
NOTE: The maximum continuous current from equipment under any external
load conditions shall not exceed a current limit that is suitable for the minimum
wire gauge used in interconnecting cables. The ratings on the connecting unit's
supply input should be considered to prevent overloading the wiring.
NOTE: Connect the flying ground lead to earth ground.
8 • iMedia Wall Mount Computer Center: IM-WCC
Operations & Installation Guide - DOC. 6382
Crestron IM-WCC
iMedia Wall Mount Computer Center
Rear Side Connection
Front Side Connections
System Configuration
Refer to the latest version of the IM-RX1 & IM-RX3 Operations and Installation
Guide (Doc. 6384), available from the Crestron website
(http://www.crestron.com/manuals) for detailed IM system configuration
instructions.
Operations & Installation Guide – DOC. 6382
iMedia Wall Mount Computer Center: IM-WCC • 9
iMedia Wall Mount Computer Center
Crestron IM-WCC
Problem Solving
Troubleshooting
The following table provides corrective action for possible trouble situations. If
further assistance is required, please contact a Crestron customer service
representative.
IM-WCC Troubleshooting
TROUBLE
POSSIBLE
CAUSE(S)
CORRECTIVE ACTION
PWR LED
does not
illuminate.
Not receiving power.
Verify that the iMedia cable and the
AC cable are properly attached.
Incorrect power supply.
Only use Crestron power supplies.
No video
output
displayed.
Incorrect cable
connection.
Verify computer cable connection.
Video from
RGB source is
garbled or no
output.
Incorrect cable
connections.
Verify 15-pin computer cable
connection. Verify iMedia output
cable connections.
Button does
not function
when pressed.
Incorrect cable connection.
Verify iMedia output cable
connection is secure.
Verify maximum iMedia cable
length.
Other functions Connections to projector.
operate, but
does not
control the
projector.
Verifythat the iMedia output cable
connection is secure.
Verify cable wiring and connections
between receiver and projector.
Further Inquiries
If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team
by calling the Crestron corporate headquarters at 1-888-CRESTRON
[1-888-273-7876]. For assistance in your local time zone, refer to the Crestron
website (www.crestron.com) for a listing of Crestron worldwide offices.
You can also log onto the online help section of the Crestron website to ask
questions about Crestron products. First-time users will need to establish a user
account to fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features, and extends the capabilities
of the IM-WCC, additional information may be made available as manual
updates. These updates are solely electronic and serve as intermediary
supplements prior to the release of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
10 • iMedia Wall Mount Computer Center: IM-WCC
Operations & Installation Guide - DOC. 6382
Crestron IM-WCC
iMedia Wall Mount Computer Center
Return and Warranty Policies
Merchandise Returns / Repair Service
1.
No merchandise may be returned for credit, exchange, or service without prior
authorization from CRESTRON. To obtain warranty service for CRESTRON products,
contact the factory and request an RMA (Return Merchandise Authorization) number.
Enclose a note specifying the nature of the problem, name and phone number of contact
person, RMA number, and return address.
2.
Products may be returned for credit, exchange, or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight
prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J. 07647, or its authorized
subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments
arriving freight collect or without an RMA number shall be subject to refusal.
CRESTRON reserves the right in its sole and absolute discretion to charge a 15%
restocking fee, plus shipping costs, on any products returned with an RMA.
3.
Return freight charges following repair of items under warranty shall be paid by
CRESTRON, shipping by standard ground carrier. In the event repairs are found to be
non-warranty, return freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in
materials and workmanship under normal use for a period of three (3) years from the date of
purchase from CRESTRON, with the following exceptions: disk drives and any other moving or
rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1)
year; touchscreen display and overlay components are covered for 90 days; batteries and
incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized
CRESTRON dealer. Purchasers should inquire of the dealer regarding the nature and extent of the
dealer's warranty, if any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in
any application other than that for which it was intended, or if it has been subjected to misuse,
accidental damage, modification, or improper installation procedures. Furthermore, this warranty
does not cover any product that has had the serial number altered, defaced, or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic
damages inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for
any claim made by a third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for
parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be
covered only by the unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed
or implied, nor authorizes any other party to offer any warranty, including any implied warranties
of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed
by law are limited to the terms of this limited warranty. This warranty statement supercedes all
previous warranties.
Trademark Information
All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered
trademark of Microsoft Corporation. Windows95/98/Me/XP and WindowsNT/2000 are trademarks of Microsoft
Corporation.
Operations & Installation Guide – DOC. 6382
iMedia Wall Mount Computer Center: IM-WCC • 11
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Operations & Installation Guide – DOC. 6382
(2013230)
07.05
Specifications subject to
change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising