San Jose Navigation CT-58 User guide

Add to my manuals
40 Pages

advertisement

San Jose Navigation CT-58 User guide | Manualzz
CT-58A
GPS/GSM Micro Tracker
Dec. 21st 2007
Version: 2.00
San Jose Navigation, Inc.
9F, No.105, Xicheng Rd., Banqiao City,
Taipei County 220, Taiwan (R.O.C.).
Tel: +886-2-26879500
Fax: +886-2-26878893
E-Mail: [email protected]
Web: www.sanav.com
Content
Content.............................................................................................................................................. 2
1. Hardware Description.............................................................................................................. 3
1.1
Front Face ..........................................................................................................................3
1.2
Side Face(1) ......................................................................................................................3
1.3
Side Face(2) ......................................................................................................................4
1.4
Rear Face(Battery Cap) ................................................................................................4
1.5
Package Contents............................................................................................................5
2. Specification............................................................................................................................... 6
3. Features....................................................................................................................................... 7
4. Applications................................................................................................................................ 7
5. Setup ............................................................................................................................................ 8
5.1 Change Username...................................................................................................................9
5.2 Change Password ..................................................................................................................10
5.3 Set up the GPRS APN (Access Point Name) ...............................................................11
5.4 Set up a Host Name (URL) to Transmit Data.............................................................12
5.5 Set up the Phone Number List.........................................................................................13
5.6 Set up Auto Report ...............................................................................................................14
5.7 All Parameters Reset to Default ......................................................................................15
5.8 Acquire Report of Current Position.................................................................................16
5.9 Set up E-mail Address to Receive Data........................................................................17
5.10 Set up SMTP Server...........................................................................................................18
5.11 Set up Router for Transmitting Data by URL/IP or E-mail..................................19
5.12 Request Imei Code.............................................................................................................21
5.13 Deactivate Panic mode .....................................................................................................22
5.14 Set up Panic Report ...........................................................................................................23
5.15 Set up Voice Monitoring Mode .......................................................................................24
5.16 SOS Phone Setting.............................................................................................................25
5.17 Setup Geofence Coordinate............................................................................................26
5.18 Vibration Alarm Setting....................................................................................................28
5.19 Set up TCP/ UDP Address to Transmit Data.............................................................31
5.20 AGPS Update ........................................................................................................................32
6. Respond Messages ................................................................................................................ 33
6.1 Auto Report .............................................................................................................................34
6.2 Emergency Response...........................................................................................................35
6.3 Polling Response....................................................................................................................36
6.4 Vibration Response...............................................................................................................37
6.5 Geo Fencing Response ........................................................................................................38
6.6 NMEA 0183 GPRMC Sentence ..........................................................................................39
7. Warranty.................................................................................................................................... 40
1. Hardware Description
1.1
Front Face
LED Indications
Red: GSM status light
Orange: Data communication light
Blue: GPS status light
Green or Yellow: Power charging light
Note:
A. Yellow light will light on while data while communicating the data to computer
B. Green light will light on while charging the CT-58A
1.2
Side Face(1)
Power switch
1.3
Side Face(2)
Data communication slot
I/O input slot
Power adapter hole
1.4
Rear Face(Battery Cap)
Use your thumb to press the battery cap
and then slide downward to open it.
SIM card insert slot
Battery insert slot
1.5
Package Contents
A.
DC Adapter Charger
B.
Cigar charger
C.
User Guide
2. Specification
SPECIFICATIONS
Electrics Data
Tri Band 850/1800/1900 or 900/1800/1900 Mhz
Frequency
1575.42 Mhz
Reacquisition < 1sec.
Cold < 41 sec. TTFF(Time To First Fix)
GPS Receiver
Acquisition time
Warm < 33 sec. TTFF
Hot < 3.5 sec. TTFF
Support A-GPS services
Power
Battery Power
3.7V DC Li-Ion Battery,1500mA (future version Li-ion polymer battery )
External Power
6V DC
Battery Life
40 hours (estimated)
Environmental Conditions
Operating Temperature
-20°C to +70°C
Storage Temperature
-25°C to +75°C
Relative Humidity
5% to 95 %, non-condensing
Mechanics Data
Size
8.4(L) x 6.4(W) x 2.3(H) cm
Weight
104g with battery
3. Features
A. Panic(option)
External panic button (option) can be connected to CT-58A. When panic button is pressed, CT-58A will
send out SOS report.
Press Panic
Dial the SOS phone number if
this number is defined
(please refer to chapter 5.20)
Upload messages to URL via GPRS. (The default report
frequency is a message every 60 seconds for 60 times)
No
GPRS
GPRS
comes
Send the SMS report to the phone number in the phonebook if the
report router is defined to send the message via SMS
B. Auto Report
You can set up auto report function to receive a regular report, and note that the default setup is off.
Please refer to chapter 5.6 for detailed information.
C. Vibration Sensor Built-in
The vibration sensor is embedded in CT-58A tracker. When the sudden movement cases vibration,
CT-58A will send the alarm report
4. Applications
1. Fleet management
4. Yachting watching
2. Vehicle security and recovery
5. Covert tracking
3. Assert tracking
5. Setup
CT-58A currently provides 13 commands for setup. You can setup the CT-58A by following the instructions shown
in this chapter via SMS from a cellular phone. Key the specific SMS message in your cellular phone as the
instruction and send it to the SIM number of CT-58A. The setup messages are showed in the following sections.
Note1: The default settings are shown as below.
a.
Default CT-58A ID is “username”, and please read Chapter 5.1 in order to change the ID.
b.
Default password is “0000”, and please read Chapter 5.2 in order to change the password.
c.
There’s no number in the default contact, and please read Chapter 5.5 in order to add the phone
number.
d.
Default setting of Auto Report is deactivated, and please read Chapter 5.6 in order to setup the auto
regular report.
e.
Default setting of APN is only suitable for Taiwan GSM network and please read Chapter 5.3 in order
to change the APN.
f.
Default setting of IP/domain is http://www.sanav.com/eric-gga/gprs.aspx and please read
Chapter 5.4 in order to change the IP/domain.
g.
Please be aware of the upper and lower cases when you send the SMS command to CT-58A.
Note2: Before doing any setup, please ensure CT-58A is connected with the GSM network. The red LED must
lights on. And please note that CT-58A must not be under Panic mode.
Note3: While you are keying in any setup message, note that NO space is allowed between the characters in
the SMS. Characters can be letters, commas or any signs.
Note4: Any setup message must be started with a “#” sign and ended up with a “*” sign.
Note5: Only when the password, username and setup message are correct, the CT-58A will update information
according to user’s definition. If the command is not valid, a failure report is going to be sent to the
commander cell phone.
5.1 Change Username
You can change the ID of CT-58A by below command format. No space is allowed between the
characters. For example, if you send the SMS message shown in the example below to the CT-58A, you
will change the ID from “username” to “ason”
Setup format
#「username」,「Password」,「Function Code」,「New username」*
Example:#username,0000,1,ason*
The table 5.1.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A
0000
Default password.
If you have changed the password, please use the updated one.
1
Mode 1 defines the ID setup
Ason
New ID defined by the owner.
At the maximum of 8 letters.
*
End sign.
Table 5.1.1
The table 5.1.2 shows each confirmation message reply after setup
Situation
Message Reply
Setup Succeeds
[username] + CT-58A username is updated.
Setup Fail
[username] + CT-58A username setup fail!
Incorrect password
[username] + Password setup Fail!
Incorrect username or command
format
CT-58A is in Emergency Mode
[username] + command error
[username] + in emergency, changing username is not allowed.
Table 5.1.2
5.2 Change Password
Use this SMS message example shown below to change the password of CT-58A. For example, by
following the example below, you will change the default password, “0000” to a new password, “1111”.
Setup format
#「username」,「Password」,「Function Code」,「new Password」,「new Password」*
Example:#username,0000,2,1111,1111*
The table 5.2.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
2
Mode 2 defines to change the password
1111
New password
1111
Reconfirm the password
*
End sign.
Table5.2.1
The table 5.2.2 shows each confirmation message reply after setup
Situation
Message Reply
Setup Succeeds
[username] + CT-58A101 Password is updated.
Setup Fail
[username] + Password setup Fail!
Incorrect password
[username] + Password setup Fail!
Incorrect username or SMS
format
[username] + command error
CT-58A is in Emergency Mode [username] + in emergency, changing password is not allowed.
Table 5.2.2
5.3 Set up the GPRS APN (Access Point Name)
For uploading the data to a web server, you must have a set of GPRS APN from your GSM network.
Various GSM network provides different GPRS APN settings. Please check the referential tables for APN
in the Chapter 8 before setup. If you could not find the name of your GSM service provider, please ask
your GMS service provider about the APN settings. If the username and password of APN are indefinite
or showed in blank, just leave the parameters blank (no space). You can follow the Setup Format below
to setup the APN that is provided by your GSM network.
Setup format
#「username」,「Password」,「Function Code」,「access point name」,「user」,「password」*
Example:#username,0000,3,internet,user,password*
The table 5.3.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
3
Mode 3 defines the APN
Internet
Name of APN
User
Username of APN
Password
Password of APN
*
End sign.
Table 5.3.1
The table 5.3.2 shows each confirmation message reply after setup.
Situation
Message Reply
Setup Succeeds
[username] + CT-58A101 GPRS APN is updated.
Setup Fail
[username] + CT-58A GPRS APN setup Fail!
Incorrect password
[username] + Password setup Fail!
Incorrect username or command [username] + command error
format
CT-58A is in Emergency Mode
[username] + in emergency, GPRS APN setup is not allowed.
Table5.3.2
5.4 Set up a Host Name (URL) to Transmit Data
This command (SMS) instructs the CT-58A to access an URL or fixed IP for data transmission. If you
send
the
SMS
according
to
the
example
seen
below
to
CT-58A,
the
URL
“http://www.sanav.com/eric-gga/gprs.aspx “ will be assigned to receive the data sent from the CT-58A.
Please note that the question mark “?” or any symbol is not allowed to be keyed in behind the URL. The
CT-58A will add the necessary symbol(s) on automatically.
Setup format
#「username」,「Password」,「Function Code」,「Fixed IP or URL」*
Example:#username,0000,4,http://www.sanav.com/eric-gga/gprs.aspx*
The table 5.4.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the
updated one.
0000
Default password.
If you have changed the password, please use the
updated one.
4
Mode 4 defines to trasmit data to a specific website
http://www,sanav.com/eric-gga/gprs.aspx Default domain name, Sign “?” is not allowed to write in
the area.
*
End sign.
Table 5.4.1
The table 5.4.2 is showing each confirmation message reply after setup.
Situation
Message Reply
Setup Succeeds
[username] + Device IP/Domain is updated.
Setup Fail
[username] + Device IP/Domain setup Fail!
Incorrect password
[username] + Device Password setup Fail!
Incorrect username or command [username] + command error
format
CT-58A is in Emergency Mode
[username] + in emergency, IP/Domain setup is not allowed.
Table 5.4.2
5.5 Set up the Phone Number List
Use this SMS message to predefine the cellular numbers (Max. of 5 numbers) by following the format
below.
Setup format
#「username」,「Password」,「Function Code」,「PH-01」,「PH-02」,「PH-03」*
Example:#username,0000,5,+886123456789,+492234567890,+866323456789*
Note that both adding and not adding the “+ “sign in front of the cellular phone number(s) are both
acceptable, while the”+” sign should precede the national code.
The table 5.5.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
5
Mode 5 defines the changes of the built-in phone number list.
+886123456789
1st cellular numbers, PH-01
+492234567890
2nd cellular numbers, PH-02
+866323456789
3rd cellular numbers, PH-03
*
End sign.
Table 5.5.1
The table 5.5.2 shows each confirmation message reply after setup.
Situation
Message Reply
Setup Succeeds
[username] + Device phone book is updated.
Setup Fail
[username] + Device phone book setup Fail!
Non-numeric data is input for
numbers
Incorrect password
Incorrect username or command
format
CT-58A is in Emergency Mode
[username] + Parameter error
[username] + Password setup Fail!
[username] + command error
[username] + in emergency, phone book setup is not allowed.
Table 5.5.2
5.6 Set up Auto Report
Use this command to set up the frequency of Auto Report. If you send the SMS according to the
example shown below to CT-58A, you will have an Auto Report Message every 300 seconds for 99
messages. Once the loop is done, you can send a SMS message to update/renew, or switching off it in
order to renew it.
Note: You may limit the amount of the Auto reply messages by inputting the digits from 1 to 9998
in the 「total number of report」field. When you input 9999, the Auto Report Message will not stop
unless you define a new Auto Report Setting.
Setup format
#「username」,「Password」,「Function Code」,「intervals (sec)」,「total number of report」*
Example1:#username,0000,6,300,99*
The table 5.6.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
6
Mode 6 defines to change the intervals and times of sending-back data
300
A constant interval of sending data
99
The amount of 99 messages sent automatically
*
End sign.
Table 5.6.1
The table 5.6.2 shows each confirmation message reply after setup
Situation
Message Reply
Setup Succeeds
[username] + Setup OK.Device Auto Report setting is updated.
Setup Fail
[username] + Auto Report setting Setup Fail!
Incorrect password
[username] + Password setup Fail!
Incorrect username or command
format
CT-58A is in Emergency Mode
[username] + command error
[username] + in emergency, Auto Report setting is not
allowed.
Table 5.6.2
5.7 All Parameters Reset to Default
Use this SMS message to reset CT-58A to factory default. You can just send the SMS according to the
example seen below. It will overwrite all the current parameters to default.
Setup format
#「username」,「Password」,「Function Code」*
Example:#username,0000,9*
The table 5.7.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
9
Mode 9 defines to change all the parameter to default value
*
End sign.
Table 5.7.1
The table 5.7.2 shows each confirm message reply after setup.
Situation
Message Reply
Setup Succeeds
[username] + Setup OK. Device resets to default
Setup Fail
[username] + Reset Fail!
Incorrect password
[username] + Password setup Fail!
Incorrect username or command
format
CT-58A is in Emergency Mode
[username] + command error
[username] + in emergency, reset to default is not allowed.
Table 5.7.2
5.8 Acquire Report of Current Position
You can send the SMS according to the example shown below. It will transmit current data to the web
server (URL) at once.
Setup format
#「username」,「Password」,「Function Code」*
Example:#username,0000,10*
The table 5.8.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
10
Mode 10 defines to transmit current data to the web server at once.
*
End sign.
Table 5.8.1
The table 5.8.2 shows each confirm message reply after setup.
Situation
Message Reply
Setup Succeeds
[username] + Polling OK!
Setup Fail
[username] + Polling Fail!
In mail mode, the setup parameters [username] + Mail address or SMTP server parameter is
are empty
empty
Incorrect password
[username] + Password setup Fail!
Incorrect
format
username
or
command
[username] + command error
Table 5.8.2
Note that the message reply shown in Table 5.8.2 will only be sent back to cell phone that sent the
SMS to do configuration. The caller’s ID of cellular phone must be activated in order to let the
CT-58A recognize the caller ID and response accordingly.
5.9 Set up E-mail Address to Receive Data
In addition to receiving data from URL, you can also obtain data from a specified E-mail address via
GPRS service. After setting up the APN, you can also define an E-mail address to receive data by
following the instruction below, please note that, since processing the transformation from APN to
E-mail address might cost longer time, so receiving data from URL is still recommended.
Setup format
#「username」,「Password」,「Function Code」,「Email address」*
Example:#username,0000,12,mail@San Jose.com*
The table 5.9.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
12
Mode 12 defines to setup an E-mail address data to a specific website
mail@San Jose.com
The E-mail address that receives the data.
*
End sign.
Table 5.9.1
The table 5.9.2 shows each confirmation message reply after setup.
Situation
Message Reply
Setup Succeeds
[username] + mail address Setup OK.
Setup Fail
[username] + mail address setup fail.
CT-58A is in Emergency Mode
[username] + in emergency, Mail address setting is not
allowed.
Incorrect password
[username] + Password setup Fail!
Incorrect username or command [username] + command error
format
CT-58A is in Emergency Mode
[username] + in emergency, Mail address setting is not
allowed.
Table 5.9.2
5.10 Set up SMTP Server
After setting up the E-mail address, you still have to setup a SMTP server so that the CT-58A can use
the SMTP server send E-mails. Setup SMTP by following instruction:
Setup format
#「username」,「Password」,「Function Code」,「SMTP server」*
Example:#username,0000,13,mail.sanav.com*
The table 5.10.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
13
mail.sanav.com
*
Mode 13 defines to setup a SMTP server
The SMTP server
End sign.
Table 5.10.1
The table 5.10.2 shows each confirmation message reply after setup.
Situation
Message Reply
Setup Succeeds
[username] + SMTP Setup OK.
[username] + SMTP server updated fail!
Setup Fail
[username] + SMTP server error.
CT-58A is in Emergency Mode
[username] + in emergency, SMTP server setup not allowed.
Incorrect password
[username] + Password setup Fail!
Incorrect username or command [username] + command error
format
CT-58A is in Emergency Mode
[username] + in emergency, SMTP server setting is not
allowed.
Table 5.10.2
5.11 Set up Router for Transmitting Data by URL/IP or E-mail
You can choose the router to transmit the data by URL/IP, E-mail or SMS message. Please refer to the
following table for the information of setting up the router.
The table 5.11.1 describes the meaning of each segment in the message above.
Router code
Representation
0
HTTP/SMS, send data to URL, if the URL is untouchable, then send it via SMS
instead.
1
Mail/SMS, send data to e-mail address, if the e-mail address is untouchable,
then send it via SMS instead.
2
HTTP only, send data to URL, if the URL is untouchable, it won’t send the data
by SMS.
3
E-mail only, send data to the e-mail address, if the e0mail address is
untouchable, it’s won’t send the data by SMS.
4
6
7
8
9
SMS only, send data by SMS only.
TCP/SMS, send data to an assigned IP address, if the IP is untouchable, then
send it via SMS instead.
TCP Only, only send data to an assigned IP address.
UDP/SMS; send data to an assigned IP address, if the IP is untouchable, then
send it via SMS instead.
UDP Only; only send data to an assigned IP address
Setup format
#「username」,「Password」,「Function Code」,「0, 1,2,3,4,6,7,8 or 9」*
Example:#username,0000,14,1*
The table 5.11.2 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
14
0/1/2/3/4/6/7/8/9
*
Mode 14 defines to setup router.
Please see the definition of the code above
End sign.
Table 5.11.2
The table 5.11.3 shows each confirmation message reply after setup.
Situation
Message Reply
[username] + Device is switching to HTTP/SMS mode
[username] + Device is switching to Mail/SMS mode
Setup Succeeds
[username] + Device is switching to HTTP mode
[username] + Device is switching to Mail mode
[username] + Device is switching to SMS mode
[username] + is switching to HTTP/SMS mode without success!
[username] + is switching to Mail/SMS mode without success!
Setup Fail
[username] + is switching to HTTP mode without success!
[username] + is switching to Mail mode without success!
[username] + is switching to SMS mode without success!
[username] + in emergency, switching to HTTP/SMS mode is
not allowed.
[username] + in emergency, switching to Mail/SMS mode is
not allowed.
CT-58A is in Emergency Mode
[username] + in emergency, switching to HTTP mode is not
allowed.
[username] + in emergency, switching to Mail mode is not
allowed.
[username] + in emergency, switching to SMS mode is not
allowed.
Incorrect password
[username] + Password setup Fail!
Incorrect username or command [username] + command error
format
Table 5.11.3
5.12 Request Imei Code
Imei stands for international mobile equipment identification. We offer you a command to acquire the
Imei number from CT-58A via SMS. Actually, every CT-58A budget has a different default Imei code.
You can send the SMS according to the example shown below to check its imei number so as to register
to the web server for tracking.
Setup format
#「username」,「Password」,「Function Code」*
Example:#username,0000,imei*
The table 5.12.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
imei
Mode imei is to inquire for international mobile equipment identification of
CT-58A
*
End sign.
Table 5.12.1
The table 5.12.2 shows each confirmation message reply after setup.
Situation
Message Reply
Setup Succeeds
[username] + “,[imei]”
Incorrect password
[username] + Password setup Fail!
Incorrect username or command [username] + command error
format
Table 5.12.2
5.13 Deactivate Panic mode
In this function, it helps you to deactivate panic mode forcedly. Please note the Panic sensor is
connected to I/O slot.
Setup format
#「username」,「Password」,「Function Code」*
Example:#username,0000,offpanic*
The table 5.13.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
offpanic
Mode offpanic is to deactivate the panic status of CT-58A
*
End sign.
Table 5.13.1
The table 5.13.2 shows each confirmation message reply after setup.
Situation
Message Reply
Setup Succeeds
[username] + is forced to deactivate panic status.
Setup Fail
[username] + is not in Panic mode.
Incorrect password
[username] + Password setup Fail!
Incorrect username or command [username] + command error
format
Table 5.13.2
5.14 Set up Panic Report
Use this command to set up the frequency of Panic Report. If you send the SMS according to the
example shown below to CT-58A, you will have a Panic Report Message every 300 seconds for 99
messages. Once the loop is done, you can send a SMS message to update/ renew, or switching off it in
order to renew it.
Note: You may limit the amount of the Panic reply messages by inputting the digits from 1 to 9998
in the 「total number of report」field. When you input 9999, the Panic Report Message will not stop
unless you define a new Panic Report Setting.
Setup format
#「username」,「Password」,「Function Code」,「intervals (sec)」,「total number of report」*
Example1:#username,0000,15,300,99*
The table 5.14.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
15
Mode 15 defines to change the intervals and times of the Panic report
300
A constant interval of sending data
99
The amount of 99 messages will be sent automatically
*
End sign.
Table 5.14.1
The table 5.14.2 shows each confirmation message reply after setup
Situation
Setup Succeeds
Message Reply
[username] + Setup OK. Device Panic report setting is
updated.
Setup Fail
[username] + Panic report setting Setup Fail!
Incorrect password
[username] + Password setup Fail!
Incorrect username or command
format
CT-58A is in Emergency Mode
[username] + command error
[username] + in emergency, Auto Report setting is not
allowed.
Table 5.14.2
5.15 Set up Voice Monitoring Mode
This function allows the user to select “Overhearing” or “Dial Polling” feature. User can hear the voice
around the surrounding if overhearing is selected.
Setup format:#「username」
,
「Password」
,
「Function Code」
,
「0, 1: hidden microphone 2:Voice polling」
*
Example:#username,0000,8,1*
The table 5.15.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
Username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
8
Mode 8 defines the switch between one-way phone and hidden
microphone
1 or 2
1: CT-58A will automatically switch to the voice monitoring.
2: Voice polling then CT-58A will send a GPS data via assigned router
to terminal.
*
End sign.
Table 5.15.1
The table 5.15.2 shows each confirmation message reply after setup.
Situation
Message Reply
Setup Succeeds (one-way
phone)
Setup
Succeeds
polling)
Incorrect function code
(Dial
Username, Device is switching to MIC mode
Username, Device is switching to voice polling mode
Username, is switching to MIC mode without success!
Table 5.15.2
Note:
When you are doing overhearing through the embedded microphone, you will hear some noises
("Kiala-Kiala" sound), which is made by the impact of metallic ball in vibration sensor. If you have
any questions about this, please contact us.
5.16 SOS Phone Setting
While Panic function is triggered, CT-58A will automatically call the SOS phone number if this number
is defined. The command format will be like following:
Setup format:#「username」,「Password」,「Sosphone」,「Phone Number」*
Example:#username,0000,sosphone,+886933123456*
The table 5.16.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
sosphone
Function code
+886933123456
Phone number of SOS phone
*
End sign.
Table 5.16.1
5.17 Setup Geofence Coordinate
Users can setup the Geofence by using this command. The Geofence is defined as a round area.
Therefore, the coordinates is the center and the radius is defined in meter.
Command: #username,0000,gf,2458.9741,N,12125.6460,E,500,0~3*
Text Keyed In SMS Description
#
Start sign.
username
Default ID of CT-58.
If you have changed the Username, please use the
updated one.
0000
Default password.
If you have changed the password, please use the updated
one.
gf
Mode gf means Geofence setup mode
2458.9741
Latitude
N
N = North, S = South
12125.6460
Longitude
E
E= East , W= West
500
The geofencing distance in meters
0~3
0
1
2
3
*
It will cancel the geofence.
It will trigger the alarm when the tracker is outside of the
geofence.
It will trigger the alarm when the tracker is inside of the
geofence.
It will trigger the alarm when the tracker is either outside or
inside of the geofence.
End sign.
Geofence Alarm Report:
This command is to define the report interval when Geofence is triggered.
Setup format:#「username」,「Password」,「Function Code」,「Time Interval」,「Total Report」*
Command: #username,0000,17,60,12*
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58.
If you have changed the Username, please use the updated one.
0000
Default password.
If you have changed the password, please use the updated one.
17
Mode 17 is the Geofence report interval setting
0~32,000
Time interval in second
0~9999
Total report. Note that 9999 means infinite reporting.
*
End sign.
5.18 Vibration Alarm Setting
Vibration sensor is embedded in CT-58A tracker. You can use following commands to define vibration
report as well as the situation that triggers the vibration alarm.
Setup Format:
#username,0000,vs,on,x,y,z*
Example:
#username,0000,vs,20,20,10*
Text Keyed In SMS Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the
updated one.
0000
Default password.
If you have changed the password, please use the updated
one.
vs
Mode ‘vs’ means vibration setup mode
20
Report interval. Unit: second. Minimum setting: 15 seconds.
20
Total reports
10
Vibration detecting time. That is when there is a constant
vibration for 10 seconds, CT-58A will starting to send the
report.
*
End sign.
Enable Vibration
Setup format:
#username,0000,vs,on*
Text Keyed In SMS Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the
updated one.
0000
Default password.
If you have changed the password, please use the updated
one.
vs
Mode ‘vs’ means vibration setup mode
on
To enable the vibration.
*
End sign.
Disable the vibration
Setup format:
#username,0000,vs,off,n*
Example:
#username,0000,vs,off,10*
Text Keyed In SMS Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the
updated one.
0000
Default password.
If you have changed the password, please use the updated
one.
vs
Mode ‘vs’ means vibration setup mode
off
Disable the vibration.
10
Device vibration detecting time. Unit 10 seconds. Please refer
to the Note below.
*
End sign.
Note:
When the vibration function is switched off, you can still define a period of time to detect the
vibration of the vehicle even though this function is off. When a 10 seconds is defined in the
“off” mode and vibration sensor detects the vibration exceeds 10 seconds constantly, CT-58A
will report to the terminal to alert users that the vehicle is being moved and the interval is 60
seconds and total is 3 times.
*Application of vibration of the tracker
1.
2.
3.
4.
Hide the CT-58A in different places of the vehicle such as glove box, under the passenger, driver’s seat
or the window, and back of the vehicle.
*When someone stoles the car……
Theft is switching on the engine……
*If CT-58A is hidden somewhere in your vehicle and define the alarm report, when the
CT-58A’s sensor detects sudden vibration……
When the vibration is detected and router is set SMS, this is the example that
your mobile phone will receive.
5.19 Set up TCP/ UDP Address to Transmit Data
If the user define to send the report to the TCP or UDP, please setup the TCP or UDP’s address by below
command.
Setup format:
#「username」,「Password」,「Function Code」,「TCP/ UDP address: port number」*
Example:
#username,0000,18,202.39.31.179:1337*
The table 5.19.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
18
Mode 4 defines to setup TCP/ UDP’s address
202.39.31.179
TCP or UDP’s address
1337
Port number
*
End sign.
Table 5.19.1
The table 5.19.2 is showing each confirmation message reply after setup.
Situation
Message Reply
Setup Succeeds
[username] + Device TCP/UDP is updated.
Setup Fail
[username] + IP/Domain setup Fail!
Incorrect password
[username] + Password setup Fail!
Incorrect username or command [username] + command error
format
CT-58A is in Emergency Mode
[username] + in emergency, IP/Domain setup is not allowed.
Table 5.19.2
5.20 AGPS Update
The users can use this command to update AGPS data. Below is the command format.
Setup format:
#username,0000,au,0 or 1,update time*
Example:
#username,0000,au,1,10*
The table 5.20.1 describes the meaning of each segment in the message above.
Text Keyed In SMS
Description
#
Start sign.
username
Default ID of CT-58A.
If you have changed the Username, please use the updated one.
Default password.
If you have changed the password, please use the updated one.
0000
au
The function code; it means “AGPS Update”
0 or 1
Switch on or off AGPS Update
10
The will update AGPS data every 10 hours
*
End sign.
Table 5.20.1
The table 5.20.2 is showing each confirmation message reply after setup.
Situation
Message Reply
Setup Succeeds
[username] + AU setup OK.
Setup Fail
[username] + IP/Domain setup Fail!
Incorrect password
[username] + Password setup Fail!
Incorrect username or command [username] + command error
format
CT-58A is in Emergency Mode
[username] + in emergency, AU setup is not allowed.
Table 5.20.2
6. Respond Messages
This chapter shows you how to read and understand the different response messages sent from CT-58A.
When CT-58A is in GPRS/SMS mode it will upload the data to the assigned URL first. However, if GPRS
service is not available, it will send the SMS to the predefined phone number instead. In the case of
GPRS-only mode, CT-58A will only send the data by GPRS no matter there is GPRS service or not.
Basically, there’re 3 different situations that trigger the CT-58A to response its position (Auto Report,
SMS Polling and Emergency) and are shown in the following pages.
Event Table:
This event table helps you to know what event triggers the response.
Event
Descriptions
When the monitor sends a valid Auto Report command to CT-58A, it will send a
Auto
report including an “Auto” behind each GPRMC sentence.
When the user presses the Panic button, it will send the report including an “SOS”
event behind each GPRMC sentence. No configuration is allowed in SOS mode. The
SOS
SOS mode will only be released by special commands (Master Reset and Off Panic)
and switching it off/on.
POLL
When using the SMS to poll the report, the event will be “poll”.
Vibration
GFIN
GOUT
When the vibration is triggered, CT-58A will send the report including a “Vibration”
event behind each GPRMC sentence
When a geo fencing coordinate is defines, and the tracker is moved into or out the
geo circle, CT-58A will send the report including a “GFIN/ GOUT” event behind each
GPRMC sentence
Note: When CT-58A experiences the low battery power, it will send an SMS to the 1st phone number in
the phonebook. The message will be “username, Device Power low, Check/recharge”. It
will send a second SMS when the power is really too low. The message will be “username,
Device Power too low, recharge battery”.
6.1 Auto Report
6.1.1. Uploading Auto data to URL when GPS is fixed
When execute the Auto Report according to the settings with a GPS fixed, CT-58A will upload the data
to your URL. The data format will be like the following.
Format:
URL?imei=IMEI,RMC=GPRMC,AUTO
Example:
http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
$GPRMC,024903.00,A,2458.98299,N,12125.65413,E,0.355,359.15,130308,,,A*6B
6.1.2. Uploading Auto data to URL when GPS is not fixed
Example:
http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
$GPRMC,024903.00,V,2458.98299,N,12125.65413,E,0.355,359.15,130308,,,A*6B
Field
Descriptions
IMEI
The username of CT-58A that is a unique number.
GPRMC
It is a full sentence of GPRMC including the current Lat/Long, UTC and
others.
AUTO
This is the event triggers the response.
!! Note: 1. When in GPRS or e-mail mode and there is no GPRS service, the report will be sent to the
1st predefined number. In the mean while, the “IMEI” will be changed to the “Username”
and the “username” is changeable by using SMS command.
2. The “A” is the GPRMC sentence indicates the GPS status, which is GPS fixed. If the GPS is
not fixed, letter “V” will substitute the letter “A”.
6.2 Emergency Response
When GPRS is available, CT-58A will upload the data to the URL/e-mail. If the GPRS is not available, it
will send the SMS instead. Please read Chapter 3.1 for how Panic works.
6.2.1. Uploading Emergency data to URL/e-mail when GPS is fixed
When there is GPS fixed, send a single SMS to the built-in numbers with the contents like following:
Format:
URL?imei=IMEI,RMC=GPRMC,SOS
Example:
http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
$GPRMC,024903.00,A,2458.98299,N,12125.65413,E,0.355,359.15,130308,,,A*6B,SOS
6.2.2. Uploading Emergency data to URL/e-mail when GPS is not fixed
When there is GPS fixed, send a single SMS to the built-in numbers with the contents like following:
$GPRMC,024903.00,V,2458.98299,N,12125.65413,E,0.355,359.15,130308,,,A*6B,SOS
Example:
http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
Field
IMEI
Descriptions
The username of CT-58A that is configurable.
$GPRMC It is a full sentence of $GPRMC including the Lat/Long, UTC and others.
SOS
This is the event triggers the response.
!! Note: 1. When in GPRS or e-mail mode and there is no GPRS service, the report will be sent to the
1st predefined number. In the mean while, the “IMEI” will be changed to the
“Username” and the “username” is changeable by using SMS command.
2. The “A” is the GPRMC sentence indicates the GPS status, which is GPS fixed. If the GPS
is not fixed, letter “V” will substitute the letter “A”.
6.3 Polling Response
6.3.1. Uploading Poll data to URL when GPS is fixed
When send an SMS to poll a report with a GPS fixed, CT-58A will upload a data to your URL. The data
format will be like the following.
Format:
URL?imei=IMEI,RMC=GPRMC,POLL
Example:
http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
$GPRMC,024903.00,A,2458.98299,N,12125.65413,E,0.355,359.15,130308,,,A*6B,POLL
6.3.2. Uploading Poll data to URL when GPS is not fixed
When send an SMS to poll a report without a GPS fixed, CT-58A will upload the data to your URL. The
data format will be like the following.
Example:
http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
$GPRMC,024903.00,V,2458.98299,N,12125.65413,E,0.355,359.15,130308,,,A*6B,POLL
Field
Descriptions
IMEI
The IMEI of CT-58A that is a unique number.
GPRMC
It is a full sentence of GPRMC including the previous Lat/Long, UTC and
others.
POLL
This is the event triggers the response.
!! Note: 1. When in GPRS or e-mail mode and there is no GPRS service, the report will be sent to the
1st predefined number. In the mean while, the “IMEI” will be changed to the “Username”
and the “username” is changeable by using SMS command.
2. The “A” is the GPRMC sentence indicates the GPS status, which is GPS fixed. If the GPS is
not fixed, letter “V” will substitute the letter “A”.
6.4 Vibration Response
6.4.1. Uploading vibration data to URL/e-mail when GPS is fixed
When there is GPS fixed, send a single SMS to the built-in numbers with the contents like following:
Format:
URL?imei=IMEI,RMC=GPRMC,Vibration
Example:
http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
$GPRMC,024903.00,A,2458.98299,N,12125.65413,E,0.355,359.15,130308,,,A*,Vibration
6.4.2. Uploading vibration data to URL/e-mail when GPS is not fixed
When there is GPS fixed, send a single SMS to the built-in numbers with the contents like following:
$GPRMC,024903.00,V,2458.98299,N,12125.65413,E,0.355,359.15,130308,,,A*6B,Vibration
Example:
http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
Field
IMEI
Descriptions
The username of CT-58A that is configurable.
$GPRMC It is a full sentence of $GPRMC including the Lat/Long, UTC and others.
Vibration This is the event triggers the response.
!! Note: 1. When in GPRS or e-mail mode and there is no GPRS service, the report will be sent to the
1st predefined number. In the mean while, the “IMEI” will be changed to the
“Username” and the “username” is changeable by using SMS command.
2. The “A” is the GPRMC sentence indicates the GPS status, which is GPS fixed. If the GPS
is not fixed, letter “V” will substitute the letter “A”.
6.5 Geo Fencing Response
6.5.1. Uploading vibration data to URL/e-mail when GPS is fixed
When there is GPS fixed, send a single SMS to the built-in numbers with the contents like following:
Format:
URL?imei=IMEI,RMC=GPRMC,GFIN/GOUT
Example:
http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
$GPRMC,024903.00,A,2458.98299,N,12125.65413,E,0.355,359.15,130308,,,A*,GFIN/GOUT
6.5.2. Uploading vibration data to URL/e-mail when GPS is not fixed
When there is GPS fixed, send a single SMS to the built-in numbers with the contents like following:
$GPRMC,024903.00,V,2458.98299,N,12125.65413,E,0.355,359.15,130308,,,A*6B,GFIN/GOUT
Example:
http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
Field
IMEI
Descriptions
The username of CT-58A that is configurable.
$GPRMC It is a full sentence of $GPRMC including the Lat/Long, UTC and others.
GFIN
GOUT
This is the event triggers the response.
!! Note: 1. When in GPRS or e-mail mode and there is no GPRS service, the report will be sent to the
1st predefined number. In the mean while, the “IMEI” will be changed to the
“Username” and the “username” is changeable by using SMS command.
2. The “A” is the GPRMC sentence indicates the GPS status, which is GPS fixed. If the GPS
is not fixed, letter “V” will substitute the letter “A”.
6.6 NMEA 0183 GPRMC Sentence
$GPRMC
,123456.00 ,V ,3444.12553,N ,13521.45600,E
Field#
1
2
3
4
5
69
13
#.
Description
1.
UTC: Time
Range
“12”: hh
00-23
“34”:mm
00-59
“56”: ss
00-59
00
00-99
2.
A or V
.
3-4.
Latitude
5-6.
“34”: degree
00-90
“44”: minute (integer)
00-59
“12345”: minute (fraction)
0-99999
“N”: North/South
N or S
Longitude
“135”: degree
000-180
“21”: minute (integer)
00-59
“45678”: minute (fraction)
0-99999
“E”: East/West
E or W
Note: Digits below 1/10000 are ignored.
7-8.
Null Fields
9.
UTC: Date
Any entry is ignored.
“02”: DD
01-31
“01”: MM
01-12
“97”: YY
97-40
(1997-2040)
10-12. Null Fields
13.
Checksum
Any entry is ignored.
6
,,
,020197
78
9
…
10 11 12
7. Warranty
Warranty Time Period and Repair Coverage
SAN JOSE NAVIGATION, INC. warrants CT-58A to be free from all defects and malfunctions in
materials and workmanship for a period of 12 months from the original purchase date from SAN JOSE
Navigation or authorized dealers. If the equipment functions improperly during the warranty period,
SAN JOSE Navigation will either repair or replace the unit without charge. Such repair service will
include necessary adjustments, remanufacture, and replacements. The product should be returned
freight-prepaid by the purchaser within valid warranty period. Notice that you must contact SAN
JOSE Navigation for a RMA (Return Material Authorization) number before returning the
goods for repair. Telephone assistance will also be provided during the warranty period.
Limitations
This warranty is limited only to the repair or replacement of defective parts confirmed by SAN JOSE
Navigation to be a result of faulty materials or workmanship. Instruments mechanically or physically
damaged due to the following conditions are beyond our warranty: Neglect, misuse or abuse, such
as a incorrect testing, installation, or operation. Place subject in extreme environments
beyond the limits of the specifications. Subjected to disassembling, soldering, alteration,
unauthorized repair, and electrical shock by nature. Any incidental or consequential losses
or damages result from the purchase. Disaster, accident, using any unauthentic substitutive
equipment or loss of any accessory that’s not provided by SAN JOSE Navigation.
For damages caused under the above conditions, we'll contact you to discuss replacement options.
SAN JOSE NAVIGATION, INC.
9F., No.105, Xicheng Rd., Banqiao City,
Taipei County 220, Taiwan (R.O.C.)
TEL: 886-2-26879500
FAX: 886-2-26878893
www.sanav.com
Technical Support: [email protected]

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement