Acer | Series HE-815J Series | Technical information | Acer Series HE-815J Series Technical information

TravelMate 4070/4080 Series
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on TravelMate 4070/4080 service guide.
Date
II
Chapter
Updates
Copyright
Copyright © 2006 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
SCREEN MESSAGES
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
Chapter 1
System Introduction
Features
This computer was designed with the user in mind. Here are just a few of its many features:
Platform
T
Intel® Centrino® mobile technology, featuring:
T
Intel® Pentium® M 725A/735A/740/750/760/770/780 processor (2MB L2 cache, 1.60/1.70/
1.73/1.86/2.0/2.13/2.26 GHz, 400/533 MHz FSB)
T
Intel® 915GM/915PM Express chipsets
Intel® PRO/Wireless 2200BG network connection (dual-mode 802.11b/g) Wi-Fi
CERTIFIEDTM solution, supporting Acer SignalUpTM wireless technology
T
T
Intel® Celeron M processor 370/380/390 (1 MB L2 cache, 1.50/1.60/1.70 GHz, 400 MHz FSB)
T
256 MB/512 MB of DDRII 533 memory, upgradeable to 2 GB using two soDIMM modules
Memory
Data storage
T
40/60/80/100/120 GB ATA/100 hard disk
T
DVD-Dual double-layer drive
T
DVD/CD-RW combo drive
T
DVD Super Multi double-layer
Display and graphics
T
Color Thin-Film Transistor (TFT) LCD displaying at
-- 15” XGA (1024 X 768)
-- 15.4” WXGA (1280 X 800) supporting simultaneous multi-window viewing on dual displays via
Acer GridVistaTM
T
Intel® 915GM integrated 3D graphics, featuring Intel® Graphics Media Accelerator 950 and up to
128 MB of shared memory, supporting Microsoft® DirectX® 9.0 and dual independent display
T
Intel® 915PM with ATI MobilityTM Radeon® X1300 HyperMemoryTM 256/512MB, supporting ATI
PowerPlayTM 5.0 Microsoft® DirectX® 9.0, DualViewTM
T
MPEG-2/DVD hardware-assisted capability
T
Simultaneous LCD and CRT display with LCD panel resolution at 70 Hz
Communication
T
Modem: 56K ITU V.92 modem with PTT approval; Wake-on-Ring ready
T
LAN: PCI/PCI Express® gigabit Ethernet; Wake-on-LAN ready
T
T
Chapter 1
Wireless LAN: integrated miniPCI Acer InviLinkTM 802.11b/g Wi-Fi CERTIFIEDTM solution;
supporting Acer SignalUPTM wireless technology
Wireless PAN: integrated Bluetooth®
1
Audio
T
Audio system with two built-in speakers
T
Intel® High-Definition audio support
T
Sound Blaster ProTM and MS-Sound compatible
T
S/PDIF2 (Sony/Philips Digital Interface) support for digital speakers
T
Built-in microphone
Input devices
T
88-/89-key Acer FineTouchTM keyboard
T
Touchpad with 4-way integrated scroll button
T
Four easy-launch buttons
T
Two front-panel buttons: wireless LED-button and Bluetooth® LED-button
I/O interface
T
Three USB 2.0 ports
T
PC Card slot (one Type II)
T
External display (VGA) port
T
Microphone-in jack
T
Headphone/speaker/line-out jack
T
Ethernet (RJ-45) port
T
Modem (RJ-11) port
T
DC-in jack for AC adaptor
Environment
2
T
Temperature:
T
Operating: 5 ° C to 35 ° C; Non-operating: -20 ° C to 65 ° C
T
Humidity (non-condension):
T
Operating: 20% to 80%; Non-operating: 20% to 80%
TravelMate 4070/4080
System Block Diagram
Chapter 1
3
Board Layout
Top View
4
TravelMate 4070/4080
Bottom View
1
SW1
Lid Switch
2
CN1
LCD Connector
3
CN2
Launch Board Connector
4
CN3
Modem Connector
5
CN7
Keyboard Connector
6
CN4
Bluetooth Module Connector
7
CN5
Touchpad Board Connector
8
CN6
Internal Microphone Connector
9
U17
Clock Generator
10
U4
PCMCIA Connector
11
CN9
MDC Connector
12
CN11
Internal Speaker Connector
13
CN13
Power Jack
14
CN12
CRT Connector
15
CN14
Battery Connector
16
CN15
Optical Disk Drive Connector
17
CN17
RJ45 & RJ11 Connector
18
CN26
Wireless LAN Controller
19
U11
North Bridge
20
U13
CPU Socket
21
CN20
USB Connector
22
CN21
USB Connector
23
U19
BIOS ROM
24
U4
EC PC97551 (Power and I/O
Connector)
25
CN22
RTC Battery
26
CN18
Memory Socket 1
27
U1
LAN Chipset RTL8100CL
28
CN19
Memory Socket 2
Chapter 1
5
6
29
U18
South Bridge
30
CN24
PCMCIA Connector
31
CN25
HDD Connector
32
CN27
USB Connector
33
CN28
Line-out/SPEDIF Jack
34
CN29
Microphone Jack
35
CN30
Line-in Jack
36
SW3
WLAN Button
37
SW2
Bluetooth Button
38
LED2
Charger LED
39
LED1
Power LED
40
U22
Audio Codec
41
U10
Fan Connector
TravelMate 4070/4080
Panel
This is a brief introduction to the I/O ports, the features and the indicators.
Front view
#
Item
Description
1
Display screen
Also called LCD (Liquid Crystal Display), displays computer
output.
2
Microphone
Internal microphone for sound recording.
3
Keyboard
For entering data into you computer.
4
Palmrest
Comfortable support area for your hands when you use the
computer.
5
Click buttons (Left, center and right)
The left and right buttons function like the left and right
mouse buttons; the center button serves as a 4-way scroll
button.
6
Touchpad
Touch-sensitive pointing device which functions like a
computer mouse.
7
Status indicators
LEDs (Light Emitting Diodes) that turn on and off to show
the status of the computer and its functions and
components.
8
Easy-Launch buttons
Buttons for launching frequently used programs.
9
Power button
Turns the computer on and off.
Chapter 1
7
Closed front view
#
Description
Left and right speakers deliver stereo audio
output.
2
Power indicator
Lights up when the computer is on.
3
Battery indicator
Lights up when the battery is being charged.
4
Bluetooth communication button/
indicator
Press to enable/disable the Bluetooth function.
Indicates the status of Bluetooth communication
(optional).
6
7
#
Item/ Port
Speakers
5
Item
#
Icon
1
Item
Wireless communication button/
Description
indicator
Press to enable/disable the wireless function.
Indicates the status of wireless LAN
communication (optional).
Line-in jack
Accepts audio line-in devices (e.g., audio CD
player, stereo walkman).
Microphone jack
Accepts inputs from external microphones.
Description
8
Speaker/Line-Out/Headphone jack
Connects to audio line-out devices (e.g.,
speakers, headphones).
9
USB 2.0 port
Connects to Universal Serial Bus (USB) 2.0
devices (e.g., USB mouse, UsB camera).
Left view
8
TravelMate 4070/4080
#
Icon
Item/ Port
Description
1
Optical drive
Internal optical drive; accepts CDs or DVDs
depending on the optical drive type.
2
LED indicator
Lights up when the optical drive is active.
3
Optical drive eject button
Ejects the optical drive tray from the drive.
4
Emergency eject hole
Ejects the optical drive tray when the computer is
turned off.
Right view
#
Icon
Item/ Port
Description
1
PC Card slot eject button
Ejects the PC Card from the slot
2
PC card slot
Accepts one Type II CardBus PC Card.
3
Two USB 2.0 ports
Connects to Universal Serial Bus (USB) 2.0
devices (e.g., USB mouse, USB camera).
4
Network jack
Connects to an Ethernet 10/100 based
network.
5
Modem jack
Connects to a phone line.
6
Ventilation slots
Enable the computer to stay cool, even after
prolonged use.
Rear view
Chapter 1
9
#
Icon
Port
Description
1
Power jack
Connects to an AC adaptor.
2
External display port
Connects to a display device (e.g., external
monitor, LCD projector).
3
Security keylock
Connects to a Kensington-compatible
computer security lock.
Bottom view
#
1
Item
Hard disc bay
Description
Houses the computer’s hard disc (secured by a screw).
2
Battery release latch
Unlatches the battery to remove the battery pack.
3
Battery bay
Houses the computer’s battery pack.
4
Battery lock
Locks the battery in place.
5
Cooling fan
Helps keep the computer cool.
Note: Do not cover or obstruct the opening of the fan.
6
10
Memory comparment
House the computer’s main memory.
TravelMate 4070/4080
Indicators
The computer has three easy-to-read status icons on the upper-right above the keyboard, and four on the front
panel.
Icon
Function
Icon
Description
Function
Description
Caps Lock
Lights when Caps Lock is activated.
Num Lock
Lights when Numeric Lock is activated.
Media activity
Indicates when the hard disk or optical
drive is active.
Power
Lights when the computer is on.
Battery
Lights when the battery is being charged.
Bluetooth
Indicates the status of Bluetooth
communication.
Wireless LAN
Indicates the status of Bluetooth
communication.
NOTE: 1. Charging: the light shows amber when the battery is charging.
NOTE: 2. Fully charged: light shows green when in AC mode.
Chapter 1
11
ction
Function
Hot Key
Icon
Function
Description
Fn-F1
Description
Easy-Launch Buttons
Fn-F2
Located at the upper-right, above the keyboard are four buttons. These buttons are called launch keys. They
are mail, Web browser, Acer Empowering key “
eManager" on page 23
"Acer
“, and
one user-programmable button.
"Acer
“ to run
the Acer eManager. The mail and Web buttons are pre-set ot email and internet programs,
but can be reset by users. To set the Web browser, mail and programmable keys, run the Acer Launch
Manager.
Fn-F3 Press “
eManager" on page 23
"Acer eManager" on page
23
Fn>
"Acer eManager" on page
23
Fn-F4
Description
Launch key
Default application
P
User-programmable
Acer eManager (user-programmable)
"Acer
eManager" on page 23
Web browser
Internet browser (user-programmable)
Mail
Email application (user-programmable)
"Acer eManager" on page
23
12
TravelMate 4070/4080
Using the keyboard
The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and
twelve function keys.
Lock keys and embedded numeric keypad
The keyboard has three lock keys which you can toggle on and off.
Lock key
Caps Lock
Description
When @is on, all alphabetic characters typed are in uppercase.
@
Num Lock <Fn>+<F11>
]
When ] is on, the embedded keypad is in numeric mode. The keys function
as a calculator (complete with the arithmetic operators ), -, *, and /). Use this mode
when you need to do a lot of numeric data entry. A better solution would be to
connect an external keypad.
Scroll Lock <Fn>+<F12>
When [ is on, the screen moves one line up or down when you press the up
[
or down arrow keys respectively. [ does not work with some applications.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired access
Num lock on
Num lock off
Number keys on embedded
keypad
Type numbers in a normal manner.
Cursor-control keys on embedded
keypad
Hold <Shift> while using cursor-control
keys.
Hold <Fn> while using cursorcontrol keys.
Main keyboard keys
Hold <Fn> while typing letters on embedded
keypad.
Type the letters in a normal manner.
Windows keys
The keyboard has two keys that perform Windows-specific functions.
Chapter 1
13
Keys
Description
Start button. Combinations with this key perform shortcut functions. Below
are a few examples:
Windows logo key
+ <Tab> (Activates the next Taskbar button)
+ <E> (Opens the My Computer window)
+ <F1> (Opens Help and Support)
+ <F> (Opens the Find: All Files dialog box)
+ <R> (Opens the Run dialog box)
+ <M> (Minimizes all windows)
<shift>+
Application key
+< M> (Undoes the minimize all windows)
This key has the same effect as clicking the right mouse button; it opens the
application’s context menu.
Hot Keys
The computer employs hot keys or key combinations to access most of the computer’s controls like screen
contrast and brightness, volume output and the BIOS Utility.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hot key combination.
Hot Key
14
Icon
Function
Description
Fn-l
Hotkey help
Displays a list of the hotkeys and their functions.
Fn-m
Acer eSetting
Launches Acer eSetting in the eManager set by the
Acer Empowering key..
TravelMate 4070/4080
Hot Key
Icon
Function
Description
Fn-n
Power Management
Launches Power options.
Fn-o
Sleep
Puts the computer in Sleep mode.
Fn-p
Display toggle
Switches display output between the display screen,
external monitor (if connected) and both the display
screen and external monitor.
Fn-q
Screen blank
Turns the display screen backlight off to save power.
Press any key to return.
Fn-r
Touchpad Toggle
Turns the internal touchpad on and off.
Fn-s
Speaker toggle
Turns the speakers on and off.
Fn-w
Volume up
Increases the sound volume.
Fn-y
Volume down
Decreases the sound volume.
Fn-x
Brightness up
Increases the screen brightness.
Fn-¨z
Brightness down
Decreases the screen brightness.
Special keys
You can locate the Euro symbol at the upper-center (for European keyboard) and/or bottom-right (Chinese
keyboard) of your keyboard. To type:
Chapter 1
15
The Euro symbol
1.
Open a text editor or word processor.
2.
Either directly press the <Euro> key at the bottom-right of the keyboard (for Chinese keyboard), or hold
<Alt Gr> and then press the <5> key at the upper-center of the keyboard.symbol at the upper-center of
the keyboard (for European keyboard, you can use both method).
NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
The US dollar sign
1.
Open a text editor or word processor.
2.
Either directly press the <Euro> key at the bottom-right of the keyboard (for Chinese keyboard), or hold
<Shift> and then press the <4> key at the upper-center of the keyboard.symbol at the upper-center of the
keyboard (for European keyboard, you can use both method).
NOTE: This function varies according to the language settings.
16
TravelMate 4070/4080
Touchpad
The built-in touchpad is a pointing device that senses movement on its surface. This means the cursor
responds as you move your finger on the surface of the touchpad. The central location on the palmrest
provides optimum comfort and suuport.
Touchpad basics
The following items teach you how to use the touchpad:
* Move your finger across the touchpad (2) to move the cursor.
* Press the left (1) and right (4) buttons located on the edge of the touchpad to do selection and execution
functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the touchapd is
the same as clicking the left button.
* Use the 4-way scroll (3) button to scroll up or down and move left or right a page. This button mimics your
cursor pressing on the right scroll bar of Windows applications.
Function
Left button (1)
Right button (4)
Touchpad (2)
Execute
Click twice quickly.
Tap twice (at the same speed
as double-clicking a mouse
button).
Select
Click once.
Tap once.
Drag
Click and hold,
then use finger to
drag the cursor on
the touchpad.
Tap twice (at the same speed
as double-clicking a mouse
button); hold finger to the
touchpad on the second tap
and drag the cursor.
Access
context menu
Scroll
Center button (3)
Click once.
Click and hold to
move up/down/left/
right.
NOTE: Keep your fingers dry and clean when using the touchpad. Also keep the touchpad dry and clean. The
touchpad is sensitive to finger movement, hence, the lighter the touch, the better the response. Taping
harder will not increase the touchpad’s responsiveness.
Chapter 1
17
Acer Empowering Technology
Acer’s innovative Empowering Technology makes it easy for you to access frequently used functions and
manage your new Acer notebook. It features the following handy utilities:
T
T
T
T
T
T
T
T
Acer eDataSecurity Management protects data with passwords and advanced encryption algorithms.
Acer eLock Management limits access to external storage media.
Acer ePerformance Management improves system performance by optimizing disk space, memory and
registry settings.
Acer eRecovery Management backs up/recovers data flexibly, reliably and completely.
Acer eSettings Management accesses system information and adjusts settings easily.
Acer eNet Management hooks up to location-based networks intelligently.
Acer ePower Management extends battery power via versatile usage profiles.
Acer ePresentation Management connects to a projector and adjusts display settings conveniently.
For more information, press the <
> key to launch the Empowering Technology menu, then click on the
appropriate utility and select the Help function.
Acer eDataSecurity Management
Acer eDataSecurity Management is handy file encryption utility that protexts your files from being accessed by
unauthorized persons. It is conveniently integrated with Windows explorer as a shell extension for quick and
18
TravelMate 4070/4080
easy data encryption/decryption and also supports on-the-fly file encryption for MSN Messager and Microsoft
Outlook.
There are two passwords that can be used to encrypt/decrypt a file; the supervisor passowrd and the filespecific password. The supervisor passwork is a “master” password that cna decrypt any file on your system;
the file-specific password will be used to encrypt files by default, or you cna choose to enter your own filespecific password when encrypting a file.
NOTE: The password used encrypt a file is the unique key that the system needs to decrypt it. If you lose the
password, the supervisor password is the only other key capable of decrypting the file. If you lose both
passwords, there will be no way to decrypt your encryped file! Be sure to safeguard all related
passwords!
Chapter 1
19
Acer eLock Management
Acer eLock Management is a security utility that allows you to lock up your removable data, optical and floppy
drives to ensure that data can’t be stolen while your notebook is unattended.
T
T
T
Removable data devices - includes USB disk drives, USB pen drives, USB flash drives, USB MP3 drives,
USB memory card readers, IEEE 1394 disk drives and any other removable disk drives that can be
mounted as a file system when plugged into the system.
Optical drive deivces - includes any kind of CD-ROM or DVD-ROM drives.
Floppy disk drives - 3.5-inch disks only.
To activate Acer eLock Management, a password must be set first. Once set, you may apply lock to any of the
three kinds of devices. Lock(s) will immediately be set without any reboot necessary, and will remain locked
after rebooting, until unlocked.
If you do not set a password, Acer eLock Management will reset back to the initial status with all locks
removed.
NOTE: If you lose your password, there is no method to reset it except by reformatting your notebook or taking
your notebook to anAcer Customer Serivce Center. Be sure to remember or write down your password.
20
TravelMate 4070/4080
Acer ePerformance Management
Acer ePerformance Management is a system optimization tool that boosts the performance of your Acer
notebook. It provides you with the following options to enhance overall system performance:
T
T
T
Memory optimization - releases unused memory and check usage.
Disk optimization - removes unneeded items and files.
Speed optimization - improves the usability and performance of your Windows XP system.
Chapter 1
21
Acer eRecovery Management
Acer eRecovery Management is a powerful utility that does away with the need for recovery disks provided by
the manufacturer. The Acer eRecovery Management utility occupies space in a hidden partition on your
system’s HDD. User-created backups are stored on D:\ drive. Acer eRecovery Management provides you
with:
T
T
T
Password protection.
Recovery of applications and drivers.
Image/data backup:
T
T
22
Back up to HDD (set recovery point).
T
Back up to CD/DVD.
Image/data recovery tools:
T
Recover from a hidden partition (factory defaults).
T
Recover from the HDD (most recent user-defined recovery point).
T
Recover from CD/DVD.
TravelMate 4070/4080
NOTE: If your computer did not come with a Recovery CD or System CD, please use Acer eRecovery
Management’s “System backup to optical disk” feature to burn a backup image to CD or DVD. To
ensure the best results when recovering your system using a CD or Acer eRecovery Management,
detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer
ezDock.
Acer eSettings Management
Acer eSettings Management allows you to inspect hardware specifications and to monitor the system health
status. Furthermore, Acer eSettings Management enables you to optimize your Windows operating system, so
your computer runs faster, smoother and better.
Acer eSettings Management also:
Chapter 1
T
Provides a simple graphical user interface for navigating through the program effortlessly.
T
Displays general system status and advanced monitoring for power users.
T
Logs when a hardware component has been removed or replaced.
T
Permits you to migrate personal settings.
T
Keeps a history log of all alerts that were previously issued.
23
Acer eNet Management
Acer eNet Management helps you to quickly and easily connect to both wired and wireless networks in a
variety of locations. To access this utility, either click on the “Acer eNet Management” icon on your netebook,
or start the program from the Start menu. You also have the option to set Acer eNet Management to start
automatically when you boot up your PC.
Acer eNet Management automatically detects the best settings for a new location, while offering you the
freedom to manually adjust the settings to match your needs, simply by right-clicking on the icon in the taskbar.
24
TravelMate 4070/4080
Acer eNet Management can save network settings for a location to a profile, and automatically apply the
appropriate profile when you move fromone location to another. Settings stored include network connection
settings (IP and DNS settings, wireless AP details, etc.), as well as default printer settings.
Security and safety concerns mean that Acer eNet Management does not store username and password
information.
Acer ePower Management
Acer ePower Management features a straightforward user interface. To launch it, select Acer ePower
Management from the Empowering Technology interface, or double-click the Acer ePower Management icon
in the task tray.
Acer Mode
The default setting is “Maximum Performance.” You can adjust CPU speed, LCD brightness and other
settings, or click on buttons to turn the following functions on/off: Wireless LAN, Bluetooth, CardBus, Memory
Card, Audio, and Wired LAN.
DC Mode
To suit your usage, there are four pre-defined profiles - Entertainment, Presentation, Word Processing, and
Maximum Battery. Or, you can define up to three of your own profiles.
Create new power scheme
1.
Assign a name for the new scheme.
2.
Choose existing scheme to use as a template.
3.
Select whether used for mains (AC) or batery mode.
4.
Choose which power options best fit your needs, then click OK.
5.
The new profile will appear on the main screen.
Chapter 1
25
Battery status
For real-time battery life estimates based on current usage, referto the panel on the lower left-hand side of the
window.
You can also click “Advanced Settings” to:
T
T
T
T
26
Set alarms.
Re-load factory defaults.
Select what actions will be taken when the cover is closed, and set passwords for accessing the system
after Hibernation or Standby.
View information about Acer ePower Management.
TravelMate 4070/4080
Acer ePresentation Management
Acer ePresentation Management lets you select from two of the most common projector resolutions: XGA and
SVGA.
Chapter 1
27
Hardware Specifications and Configurations
System Board Major Chip
Item
Controller
System core logic
Intel 915GM/915PM Express chipsets+ICH6-M
Memory controller
®
Integrated in Intel 915GM
Audio controller
RealTek ALC833(ALC260) HD audio interface
®
(Audio amplifer: Maxiam MAX9755)
PCMCIA controller for socket
TI PCI1510A
Video controller
Integrated in Intel® 915GM for UMA models
®
ATI X1300 RADEON for discrete models
Power and Keyboard controller
KBC NS97551/541V
Wireless controller (mini PCI)
Intel (The controller is on the Wireless LAN card. Please look at the
wireless LAN card for controller details).
Processor
Item
CPU type
Specification
®
®
Intel Pentium M 730/740/750/760/770/780 processor (2MB L2 cache,
1.60/1.73/1.86/2/2.13/2.26 GHz, 533 MHz FSB)
Intel® Pentium® M 725 processor (2MB L2 Cache, 1.60 GHz, 400 MHz FSB)
®
®
Intel Celeron M processor 360/370/380 (1 MB L2 cache, 1.40/1.50/1.60
GHz, 400 MHz FSB)
CPU package
Intel socketable 478 pins Micro-FCPGA
CPU core voltage
Low speed: 0.8V
CPU I/O voltage
1.2V
High speed: 1.5V
BIOS
Item
BIOS vendor
Specification
Pheonix BIOS
BIOS Version
BIOS ROM type
Flash ROM, SST39VF040
BIOS ROM size
512Kbyte
BIOS package
32 Pin PLCC-lead
Supported protocols
ACPI 2.0 (if available, at least 1.0b), SMBIOS 2.3, PCI 2.2, Boot Block,
PXE 2.0, Mobile PC2001, Hard Disk Password, INT 13h Extensions, PCI
Bus Power Management interface Specification, EI Torito-Bootable CDROM Format Specification V1.0, Simple Boot Flag 1.0
Second Level Cache
Item
Specification
Cache controller
Built-in CPU
Cache size
2MB for Intel® Pentium® M processor
®
®
1MB for Intel Celeron M processor
1st level cache control
28
Always Enabled
TravelMate 4070/4080
Second Level Cache
Item
Specification
2nd level cache control
Always Enabled
Cache scheme control
Fixed-in write back
System Memory
Item
Specification
Memory controller
built-in CPU
Onboard memory size
0MB
DIMM socket number
2 Sockets
Supports memory size per socket
256MB(min)/1024MB(max)
Supports maximum memory size
2GB with 2 SODIMM support
Supports DIMM type
DDRII
Supports DIMM Speed
533MHz
Supports DIMM voltage
1.8 V/0.9V
Supports DIMM package
200-pin so-DIMM
Memory module combinations
You can install memory modules in any combinations as long as they
match the above specifications .
Memory Combinations
Slot 1
Slot 2
Total Memory
0MB
256MB
256MB
0MB
512MB
512MB
0MB
1024MB
1024MB
256MB
0MB
256MB
256MB
256MB
512MB
256MB
512MB
768MB
256MB
1024MB
1280MB
512MB
0MB
512MB
512MB
256MB
768MB
512MB
512MB
1024MB
512MB
1024MB
1536MB
1024MB
0MB
1024MB
1024MB
256MB
1280MB
1024MB
512MB
1536MB
1024MB
1024MB
2048MB (2G)
Above table lists some system memory configurations. You may combine DIMMs with various capacities to
form other combinations.
LAN Interface
Item
Specification
Chipset
RealTek 8100CL
Supports LAN protocol
10/100
LAN connector type
RJ45
LAN connector location
Right side
Chapter 1
29
Modem Interface
Item
Specification
Chipset
CS1037 Internal Agere Scorpio chipset (Scorpio+CSP1037B)
Fax modem data baud rate (bps)
14.4K
Data modem data baud rate (bps)
56K
Supports modem protocol
V.92MDC
Modem connector type
RJ11
Modem connector location
Right side
Wireless Module 802.11b/g (optional device)
Item
Specification
Chipset
Data throughput
11M~54M bps
Protocol
802.11 b+g
Interface
Mini-PCI type II
Floppy Disk Drive Interface
Item
Specification
Vendor & model name
There is no FDD module for this product
Floppy Disk Specifications
Media recognition
2DD (720KB)
2HD (1.2 MB, 3 mode)
2HD (1.44MB)
Sectors/track
9
15
18
Tracks
80
80
80
Data transfer rate
(Kbit/s)
1 MB
1.6 MB
2 MB
Rotational speed (RPM)
300
360
300
Read/write heads
2
Encoding method
MFM
Power Requirement
Input Voltage (V)
+5V
.
Hard Disk Drive Interface
Item
Vendor & Model
Name
HGST MORAGA
IC25N060ATMR04-0
08K0634
HGST MORAGA
IC25N080ATMR04-0 08K635
TOSHIBA PLUTO
MK1031GAS
Seagate N2 ST9808210A
SEAGATE N2 ST9100822A
Seagate N2 ST960821A
TOSHIBA PLUTO
MK6025GAS
TOSHIBA PLUTO
MK6025GAS
Capacity (MB)
60000
80000
100000
Bytes per sector
512
512
512
Logical heads
16
16
16
Logical sectors
63
63
63
16383
16383
16383
Drive Format
Logical cylinders
30
TravelMate 4070/4080
Hard Disk Drive Interface
Item
Physical read/write
heads
3/3/4
4/3/2
4
Disks
2/2/4
2/2/4
2
Spindle speed (RPM)
4200RPM
4200RPM
4200RPM
8MBytes (8192kbytes)
8MBytes
Performance Specifications
Buffer size
8MBytes (8192kbytes)
Interface
ATA-6
ATA/ATAPI-6
ATA/ATAPI-6
Data transfer, rate
(host~buffer, Mbytes/
s)
100 MB/Sec
100 MB/Sec
100 MB/Sec
5 +/- 5%
5 +/- 5%
DC Power Requirements
Voltage tolerance
5 +/- 5%
Combo Drive Interface
Item
Vendor & model name
Specification
Remark
DVD/CDRW TOSHIBA TS-L462A
General Specification
Interface
Enhanced IDE (ATAPI)
Disc Diameter
8cm/12cm
Loading Type
Drawer Type
Drive Mounting
Horizontal/Vertical
Read/Write
Read Speed:
Max. 24X(3,600 KB/sec) for CD-ROM
Max. 24X(3,600 KB/sec) for CD-RW
Write Speed:
Max. 24X(3,600 KB/sec) for CD-R
Max. 10X(1,500 KB/sec) for CD-RW
Max. 24X(3,600 KB/sec) for US-RW
Mounting Orientation
Horizontal/Vertical
CAV 24X
CAV 24X
P-CAV 24X/20X/16X ; CLV 10X/8X/4X
CLV 10X/4X
P-CAV 24X/16X
All angles
Buffer Under Run
2MB
Power consumption
DC +5v/1.2A
Interface
Enhanced IDE(ATAPI) compatible
Media compatibility
CD:
120mm CD-ROM (Read Only)
80mm CD
800/700/650/550MB CD-Recordable (Read & Write)
700/650MB CD-Rewritable (Read & Write)
700/650MB High Speed CD-Rewritable (Read & Write)
DVD:
5/9/10/18 DVD-Single/Dual (PTP, OTP)
3.9/4.7G DVD-R (Read Only)
4.7GDVD+R (Read Only)
DVD±RW (Read only)
80mm DVD
Chapter 1
31
Combo Drive Interface
Item
Specification
Remark
Format compatibility
CD
CD-DA (Red Book) - Standard Audio CD & CD-TEXT
CD-ROM (Yellow Book Mode1 & 2) - Standard Data
CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session
CD-I /FMV (Green Book, Mode2 Form1 & 2, Ready, Bridge)
CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video
Video-CD (White Book) - MPEG1 Video
DVD
DVD-ROM (Book 1.02),
DVD-Video (Book 1.1)
DVD-R (Book 1.0, 3.9G)
DVD-R (Book 2.0, 4.7G) - General & Authoring
DVD+R (Version 1.0)
DVD±RW
Play DVD-AUDIO except the case that required CPPM
(Content protection for prerecorded Media)
Write Method
Loading mechanism
Load: Manual
Release: (a) Electrical Release
(Release Button)
(b) Release by ATAPI
command
(c) Emergency Release
Power Requirement
Input Voltage
DC +5V+/- 5% (operation)
DC +5V+/- 8% (start up)
DVD-RW Interface
Item
Vendor & model name
Specification
TOSHIBA TS-L532A
Performance Specification
Transfer rate (KB/sec)
(1) Read DVD-ROM
DVD-R
CD-ROM
(2) Write CD-R
CD-RW
HS-RW
US-RW
(3) ATAPI Interface
PIO mode
DMA mode
Ultra DMA mode
32
MAX 8X CAV (MAX 10800kB/s)
MAX 4X CAV (MAX 5400kB/s)
MAX 24X CAV (MAX 3600kB/s)
4X, 8X (CLV), MAX. 24X(ZCLV)
4X
(CLV)
4X, 8X, 10X (CLV)
8X, 10X(CLV), MAX. 16X (ZCLV)
16.6MB/s: PIO mode4
16.6MB/s: Multi word mode2
33.3MB/s: Ultra DMA mode2
Buffer Memory
2MB
Interface
Enhanced IDE(ATAPI) compatible
Applicable disc format
Read:
copy-protected DVD discs, CD-ROM, CD audio, DVD-ROM and DVD-RAM,
DVD-R/-RW, DVD+R/+RW and CD-R/-RW, DVD-ROM, DVD-R/+R, DVD-R/+R,
DVD-RW/+RW, 4.38GB DVD-RAM, CD-DA discs, CD-ROM discs, CD-R discs,
CD-RW discs
Write:
CD-R, CD-RW, high-speed CD-RW, Ultra-speed CD-RW, DVD-R, DVD-RW,
DVD+R, DVD+RW
TravelMate 4070/4080
DVD-RW Interface
Item
Specification
Loading mechanism
Load: Manual
Release: (a) Electrical Release (Release Button)
(b) Release by ATAPI command
(c) Emergency Release
Power Requirement
Input Voltage
5 V +/- 5 % (Operating)
Audio Interface
Item
Specification
Audio Controller
Realtek ALC260 (Audio amplifier: Maxim MAX9755)
Audio onboard or optional
Built-in
Mono or Stereo
Stereo
Resolution
18 bit stereo full duplex
Compatibility
HD audio Interface; S/PDIF output for PCM or AC-3 content
Sampling rate
1Hz resolution VSR (Variable Sampling Rate)
Internal microphone
Yes
Internal speaker / Quantity
Yes
Supports PnP DMA channel
DMA channel 0
DMA channel 1
Supports PnP IRQ
IRQ10, IRQ11
Video Interface
Item
Specification
Vendor & Model Name
built-in Intel
Video memory size
®
915GM
up to 128MB for Aspire 3000/5000
up to 64MB for Aspire 3500
Chip voltage
Core / 2.5V, 1.5V,
Supports ZV (Zoomed Video) port
NO
Graph interface
4X AGP (Accelerated Graphic Port) Bus
Maximum resolution LCD
1600X1200 (UXGA)
Maximum resolution CRT
2048X1536@60HZ
Video Resolutions Mode
Monitor Resolution
Hz
2D Display Mode
640x480
120
800x600
120
1024x768
120
1152X864
120
1280X1024
120
1600x1200
85
1920x1080*16:9
75
1920x1200
75
1920x1440
75
Chapter 1
33
Video Resolutions Mode
Monitor Resolution
2048x1536
Hz
60
Resolution, colors and maximum refersh rate (Hz) in 256, 65K or 16.7M colors.
NOTE: 16:9 aspect ratio monitors are supported on 1920x1080 and 848x480 on Windows(R)XP, Windows(R)
2000 and Windows(R)ME. The complete list of resolutions depends on the driver version and operating
system. NOTE: resolutions are limited by the performance of the attached monitor.
USB Port
Item
Specification
USB Compliancy Level
2.0
OHCI
USB 2.0
Number of USB port
3
Location
Two on the right side; one on the front side
Serial port function control
Enable/Disable by BIOS Setup
PCMCIA Port
Item
Specification
PCMCIA controller
TI PCI1510A
Supports card type
Type II (No Tpye III)
Number of slots
One type II
Access location
Right side
Supports ZV (Zoomed Video) port
NO
Supports 32 bit CardBus
Yes (IRQ17)
Keyboard
Item
Specification
Keyboard controller
KBC NS97551
Keyboard vendor
Darfon
Total number of keypads
88-/89-key
Windows keys
Yes
Internal & external keyboard work simultaneously
Yes
Battery
Item
Vendor & model name
Specification
SANYO
PANASONIC
PANASONIC (RoHS)
SANYO LI-ION 4UR18650F-2-QC141
SIMPPLO
SONY
34
Battery Type
Lithium-ION
Pack capacity
4400mAH
Nominal voltage
14.8V
Number of battery cell
8
TravelMate 4070/4080
Battery
Item
Specification
Package configuration
4S2P for Sanyo and Panasonic
Package voltage
41.8V / 9.6V
4S1P for Sanyo QC141,SIMPPLO and SONY
LCD
Item
Specification
Vendor & model name
AU B154EW01-08
QDI QD15TL02-03
Screen Diagonal (mm)
15.4inch
15.4inch
Active Area (mm)
331.2(H)x207.0(V)
331.2(H)x207.0(V)
Display resolution (pixels)
WXGA (1280x800)
WXGA (1280x800)
Pixel Pitch
0.2588(H)x0.2588(H)mm
0.2588(H)x0.2588(H)mm
Pixel Arrangement
RGB vertical stripe
RGB vertical stripe
Display Mode
Normally white
Normally white
Surface Treatment
Not show
glossy, hardness 2H
Typical White Luminance (cd/m2)
180
160
Luminance Uniformity
not show
1.4(max)
Contrast Ratio
400
400
Response Time (Optical Rise Time/Fall
Time)msec
16
25(5ms for rise+20 ms for
decay)
Nominal Input Voltage VDD
not show
not show
Typical Power Consumption (watt)
6.5 (max)
4.38 (for lamp)
also called Brightness
Weight
585
585
Physical Size(mm)
344(W)x222(H)x6.5(D)
344(W)x222(H)x6.5(D)
Support Color
Native 262K colours
262K colours
40/40
10/30
45/45
15/35
0 to 50
-20 to 60
0 to 50
-20 to 60
Viewing Angle (degree)
Horizontal: Right/Left
Vertial: Upper/Lower
Temperature Range( ° C)
Operating
Storage (shipping)
AC Adapter
Item
Vendor & model name
Specification
LITE-ON PA-1650-02QR
LI SHIN SLS0335A19A57LF
DELTA SADP-65KB
Input Requirements
Maximum input AC current
3.42A
Inrush currenct
50A @ 115Vac
100A @ 230Vac
Nominal frequency (Hz)
50-60
Frequency variation range (Hz)
47-63
Input voltage range (Vrms)
90V AC-264V AC
Inrush current
The maximum inrush current will be less than 50A and 100A when the adapter
is connected to 115Vac and 230Vac respectively.
Chapter 1
35
AC Adapter
Item
Efficiency
Specification
It should provide an efficiency of 83% minimum, when measured at maximum
load under 115Vac.
Output Ratings (CV mode)
DC output voltage
19V
Noise + Ripple
300mVp-pmax (20 MHz bandwidth)
Load
0(min) 3.16A(max)
Output Ratings (CC mode)
DC output voltage
19V +/-1.0V for CV mode
Constant current mode
3.6 +/- 0.3A
Dynamic Output Characteristics
Turn-on delay time
3 sec (@ 115Vac)
Hold up time
5ms (@115Vac, Full load)
Over Voltage Protection (OVP)
24V
Short circuit protection
3.9A max can be protected and output can be shorted without damage
Electrostatic discharge (ESD)
15KV (at air discharge)
8KV (at contact discharge)
Dielectric Withstand Voltage
Primary to secondary
3000Vac
Leakage current
0.25 mA max. (@ 254Vac, 60Hz)
Regulatory Requirements
Safety Requirements:
1.The subject product rated 100-120V 60Hz must be listed under UL 1950 and
certified with SCA Standard C22.2 No.950.
2.The subject product rated 200-240V 50Hz must comply with low voltage
directive 73/23EEC.
EMI Requirements:
1.The subject product rated 100-120V 60Hz must meet the EMI requirements
of FCC part 15, Subpart B for Class B Digital Device and get FCC Certification
before marketing into USA and Canada.
2.The subject product rated 200-240V 50Hz must meet the EMC Directive 89/
336/EEC.
3.The subject product rated 100-120V must meet the VCCI-2 EMI
requirements.
Power Management
ACPI Mode
Power Management
Mech. Off (G3)
All devices in the system are turned off completely.
Soft Off (G2/S5)
OS initiated shutdown. All devices int he sytem are turned off
completely.
Working (G0/S0)
Individual devices such as the CPU and hard disk may be power
managed in this state.
S3 Sleeping State
CPU set power down
VGA suspend
PCMCIA suspend
Audio Power Down
Hard Disk Power Down
CD-ROM Power Down
Super I/O Low Power mode
S4 Sleeping State
36
Also called Hibernate stats. System saves all system state and
data onto disk prior to power off the whole system.
TravelMate 4070/4080
Environmental Requirements
Item
Specification
Temperature
Operating
+0~+35 °C
Non-operating
-20~+65 °C
Package storage
-20~+65 °C
Humidity
Operating
10% to 90% RH, non-condensing
Non-operating
10% to 90% RH, non-condensing (Unpacked)
Non-operating
10% to 90% RH, non-condensing (Storage package)
Vibration
Operating (unpacked)
Operation vibration: 1.0G ,X,Y,Zaxis, 30 minutes/axis
Non-operating (unpacked)
5~27.1Hz: 0.6G
27.1~50Hz: 0.04mm (peak to peak)
50~500Hz: 2.0G
Non-operating (packed)
5~62.6Hz: 0.51mm (peak to peak)
62.6~500Hz: 4.0G
Mechanical Specification
Item
Dimensions
Specification
364(W) x 279(D) x 33.9/38.9 (H)mm
14.3 3X 10.98x 1.33/1.53 inches
Weight
6.4 Ibs (2.91kg) for 15” XGA LCD model
6.5 lbs (2.94kg) for 15.4” WXGA LCD model
I/O Ports
Three USB 2.0 ports
Ethernet (RJ-45) port
Modem (RJ-11) port
External display (VGA) port
Microphone-in jack
Line-in jack
Headphones/speaker/line-out jack
Type II PC Card slot
DC-in jack for AC adaptor
Drive Bays
One
Indicators
LED indicator for keyboard hot key: Caps Lock, Scroll Lock, NUmber lock
LED indicator for function indicator: System power-on, HDD/ODD, Wireless on/off,
Arcade LED mode, DC-in, Battery/Charging indicator
Switch
Chapter 1
Power
37
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press m to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
PhoenixBIOS Setup Utility
Info.
Main
Security
Boot
Exit
Intel (R) Pentium (R) processor 1.73GHz
CPU Type :
1733MHz
CPU Speed :
HDD Model Name:
TOSHIBA MK1031GAS
HDD Serial Number : 751U0320S
HL-DT-ST DVD-RW GWA-4082N
ATAPI Device :
System BIOS Version : 2A02
Alviso 1219
VGA BIOS Version :
1A16
KBC Version :
LXT123456705290116EF00
Serial Number :
Asset Tag Number :
Produce Name
N/A
Aspire 1640
Manufacturer Name:
UUID :
Acer
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
F1 Help
↑↓
Select Item
F5/F6 Change Values
F9 Setup Defaults
Esc Exit
←→
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Chapter 2
38
Navigating the BIOS Utility
There are six menu options: Info., Main, System Devices, Security, Boot, and Exit.
Follow these instructions:
T
To choose a menu, use the cursor left/right keys (zx).
T
To choose a parameter, use the cursor up/down keys ( wy).
T
To change the value of a parameter, press por q.
T
A plus sign (+) indicates the item has sub-items. Press e to expand this item.
T
Press ^ while you are in any of the menu options to go to the Exit menu.
T
In any menu, you can load default settings by pressing t. You can also press u to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information vary in models.
39
Chapter 2
Information
PhoenixBIOS Setup Utility
Main
Info.
Security
Boot
Exit
Intel (R) Pentium (R) processor 1.73GHz
CPU Type :
1733MHz
CPU Speed :
HDD Model Name:
TOSHIBA MK1031GAS
HDD Serial Number : 751U0320S
HL-DT-ST DVD-RW GWA-4082N
ATAPI Device :
System BIOS Version : 2A02
Alviso 1219
VGA BIOS Version :
1A16
KBC Version :
LXT123456705290116EF00
Serial Number :
Asset Tag Number :
Produce Name
N/A
Aspire 1640
Manufacturer Name:
UUID :
Acer
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
F1 Help
↑↓
Select Item
F5/F6 Change Values
F9 Setup Defaults
Esc Exit
←→
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
NOTE: The system information is subject to different models.
Parameter
Description
HDD Model Name
This field shows the model name of HDD installed on primary IDE master.
HDD Serial Number
This field displays the serial number of HDD installed on primary IDE master.
ATAPI Device
This field displays the mofel name of devices installed on secondary IDE master. The hard
disk drive or optical drive model name is automatically detected by the system.
System BIOS Version
This field displays the BIOS version of the system.
VGA BIOS Version
This field displays the VGA BIOS version of this system.
KBC Version
This filed displays the KBC version of this system.
ATAPI Serial Number
This field shows the serial number of devices installed on secondary IDE master.
Serial Number
This field displays the serial number of this unit.
Asset Tag Number
An Asset Tag with 32 bytes will be stored in EEPROM. Default value is set as
“0000000000000000” (in binary code).
Chapter 2
40
Parameter
UUID Number
41
Description
This will be visible only when there is an internal LAN device present. UUID means
Universally Unique ID, a method for computing object identifiers (OIDs). It uses the serial
number in the local Ethernet card combined with the date and time to generate a 128 bit
(16bytes) number. For Acer product, this field displays UUID number. A UUID string will be
stored in the secured data area which is an alphanumeric string of maxium 16 bytes in
length.
Chapter 2
Main
The Main screen displays a summary of your computer hardware information, and also includes basic setup
parameters. It allows the user to specify standard IBM PC AT system parameters.
PhoenixBIOS Setup Utility
Information
Main
Security
Boot
Exit
Item Specific Help
System Time:
[05:45:48]
System Date:
[08/30/2005]
System Memory:
640 KB
<Tab>, <Shift-Tab>, or
<Enter> selects field.
Shows system base memory size
Extended Memory:
1040 MB
Shows extended memory size
Video Memory
[128MB]
VGA memory size
Quiet Boot:
[Enabled]
Power On Display:
Network Boot
[Both]
[Enabled]
F12 Boot Menu
D2D Recovery
[Disabled]
[Enabled]
F1 Help
↑↓
Select Item
F5/F6 Change Values
F9 Setup Defaults
Esc Exit
←→
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
NOTE: The screen above is for reference only. Actual values may differ.
Chapter 2
42
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Format/Option
System Time
Sets the system time. The hours are displayed
with 24-hour format.
Format: HH:MM:SS
(hour:minute:second) System Time
System Date
Sets the system date.
Format MM/DD/YYYY (month/day/
year)
System Date
System Memory
This field reports the memory size of the system.
Memory size is fixed to 640MB
Extended Memory
This field reports the memory size of the
extended memory in the system.
Extended Memory size=Total memory size-1MB
VGA Memory
Shows the VGA memory size. VGA Memory
size=64/128MB
Quiet Boot
Determines if Customer Logo will be displayed or
not; shows Summary Screen is disabled or
enabled.
Option: Enabled or Disabled
Enabled: Customer Logo is displayed, and
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and
Summary Screen is enabled.
Power on display
Auto: During power process, the system will
detect if any display device is connected on
external video port. If any external display device
is connected, the power on display will be in CRT
(or projector) only mode. Otherwise it will be in
LCD only mode.
Option: Both or Auto
Both: Simultaneously enable both the integrated
LCD screen and the system’s external video port
(for an external CRT or projector).
Network Boot
Enables, disables the system boot from LAN
(remote server).
Option: Enabled or Disabled
F12 Boot Menu
Enables, disables Boot Menu during POST.
Option: Disabled or Enabled
D2D Recovery
Enables, disables D2D Recovery function. The
function allows the user to create a hidden
partition on hard disc drive to store operation
system and restore the system to factory
defaults.
Option: Enabled or Disabled
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
43
Chapter 2
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.
Information
Main
PhoenixBIOS Setup Utility
Security
Boot
Exit
Item Specific Help
Supervisor Password Is :
User Password Is :
HDD Password Is :
HDD Master ID :
Clear
Clear
Clear
15422442
Set Supervisor Password
Set User Password
Set HDD Password
[Enter]
[Enter]
[Enter]
Password on Boot
[Disabled]
F1
Help
Esc Exit
Chapter 2
↑ ↓
←→
Supervisor Password
controls accesses of the
whole setup utility.
It can be used to
boot up when Password
on boot is enabled.
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
44
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
User Password Is
Shows the setting of the user password.
Clear or Set
Supervisor Password Is
Shows the setting of the Supervisor password.
Please note that Supervisor Password controls
access to the entire Setup. The Supervisor
Password can be used to boot up when
Password on boot is set to enabled.
Clear or Set
HDD Password Is
Shows the setting of the HDD password.
Clear or Set
Set User Password
Press Enter to set the user password. When
user password is set, this password protects
the BIOS Setup Utility from unauthorized
access. The user can enter Setup menu only
and does not have right to change the value of
parameters.
Set Supervisor Password
Press Enter to set the supervisor password.
When set, this password protects the BIOS
Setup Utility from unauthorized access. The
user can not either enter the Setup menu nor
change the value of parameters.
Set HDD Password
Press Enter to set the HDD password.
Primary Harddisk Security
This feature is available to user when
Supervisor password is set. Password can be
written on HDD only when Supervisor
password or user password is set and
password on HDD is set to enabled.
Supervisor Password is written to HDD only
when Supervisor password is being set. User
password is written to HDD when both
passwords are set. When both Supervisor and
user password are present, both passwords
can unlock the HDD.
Disabled or Enabled
Password on Boot
Defines whether a password is required or not
while the events defined in this group
happened. The following sub-options are all
requires the Supervisor password for changes
and should be grayed out if the user password
was used to enter setup.
Disabled or Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
NOTE: The User Password can chagne the following items in BIOS: System Date, System Time and Power
on Display on Main menu, System Devices menu and Set User Password function on Security menu.
Meanwhile, the Supervisor Password can change ALL settings in BIOS.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.
45
Use the w andy keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Supervisor Password box appears:
Chapter 2
2.
Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.
4.
Press e.
After setting the password, the computer sets the User Password parameter to “Set”.
If desired, you can opt to enable the Password on boot parameter.
5.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
3.
Press e twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.
4.
When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
Chapter 2
46
3.
Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4.
Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5.
If desired, you can enable the Password on boot parameter.
6.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses u.
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following
message.
47
Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Boot
Exit
Item Specific Help
CD-ROM/DVD Drive
+ and - indicate device
categories. Use <Enter> to
expand/collapses.
Floppy Devices
+Hard Drive
Network Boot
Boot order is top-down using
only the top device in each
category.
Use <F6> and <F5> to move
highlighted item up and down.
F1
Help
Esc Exit
Chapter 2
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
48
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Exit
Boot
Item Specific Help
Exit Saving Changes
Exit System Setup and save
your changes to CMOS.
Exit Dicarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1
Help
Esc Exit
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
The table below describes the parameters in this screen.
Parameter
Exit Saving Changes
49
Description
Exit System Setup and save your changes to CMOS.
Exit Discarding Changes
Exit utility without saving setup data to CMOS.
Load Setup Default
Load default values for all SETUP item.
Discard Changes
Load previous values from CMOS for all SETUP items.
Save Changes
Save Setup Data to CMOS.
Chapter 2
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
T
New versions of system programs
T
New features or options
T
Restore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Create Crisis Recovery Diskette
1.
Rename BIOS file of this product to BIOS.wph
2.
Copy BIOS.wph file to crisis folder and overwrite the original BIOS.wph file.
3.
Insert a blank floppy diskette to floppy drive.
4.
Run cs.bat and follow its instructions to create crisis recovery diskette.
Recover BIOS from Crisis Recovery Diskette
1.
Insert the crisis recovery diskette to the floppy drive.
2.
Use AC adaptor power supply.
3.
Press Fn and ESC key together for more than two seconds when you power on the system.
4.
The system will read the files inside the floppy diskette without backlight.
5.
After one to three minutes, the system will automatically reboot. Please do not shut down the system or
remove the power supply.
6.
After step 1 to 5, you sould be able to recover BIOS already. Then you can see the LCD screen with the
backlight is on.
Chapter 2
50
51
Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
T
Wrist grounding strap and conductive mat for preventing electrostatic discharge
T
Flat-bladed screw driver
T
Phillips screw driver
T
Tweezers
T
Plastic Flat-bladed screw driver
Hexed Screw Driver
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
T
Chapter 3
52
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
.
53
1.
Turn off the power to the system and all peripherals.
2.
Unplug the AC adapter and all power and signal cables from the system
NOTE: Aspire 9100 series product uses mylar or tape to fasten the FFC/FPC/connectors/cable, you may
need to tear the tape or mylar before you disconnect different FFC/FPC/connectors.
Chapter 3
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence
and instructs you on the components that need to be removed during servicing. For example, if you want to
remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in
that order.
Start
Battery
*2
HDD Module
*1
Dimm Cover
Modem Cover
Hinge Caps
*2
*2
*2
HDD
HDD Holder
Memory
Modem Board
Middle Cover
*2
*6
Keyboard
*3
*3
*11
*4
LCD Module
RTC Battery
Launch Board
*3 Mini PCI Card
Plate
*4
Lower Case
Assembly
Upper Case
Assembly
*2
*4
*1
*1
ODD Support
Bracket
HDD Bracket
Thermal
Module
W ireless LAN
Card
CPU
*4
W ireless LAN
Antenna
FDD Module
ODD Module
Disconnect
W ireless LAN
Antenna
CPU Heatsink
Plate
Touchpad
Cover
*3
VGA Heatsink
Plate
Touchpad
Button Pad
*2
*4
ODD Bracket
ODD
Main Board
*2
DC Board
Touchpad
Scroll Key
Touchpad
*4
PCMCIA Slot
Touchpad
Cable
Upper Case
*2
Speaker Set
Chapter 3
54
LCD Module
4 LCD
Cushions
*4
LCD Bezel
*1
Inverter
*4
LCD
LCD Panel
*4
LCD Coaxial
Cable
LCD Brackets
Screw List
Item
A
55
Description
SCREW F040 9 5.0X5.0 9.5X(IO) R00
B
SCREW M2.0X0.4P+3FP ZK(NL)
C
SCREW M2.5 K 5/2 X0.85 4 ZK(NL)
D
SCREW M2.5X0.45+10K NIL
E
SCREW M2.5X0.45+8K ZBL
F
SCREW M2.5X0.45P+3F NI
G
SCREW M3.0X0.8P+3K NL
Chapter 3
Removing the Battery
1.
Unlatch the battery latch then remove the battery.
Chapter 3
56
Removing the Hard Disc Drive Module
1.
See “Removing the Battery” on page 56.
2.
Remove the screw securing the hard disk drive (HDD) cover.
3.
Then remove the HDD cover.
4.
Pull the HDD module backwards as shown.
5.
Remove the HDD module.
Disassembling the Hard Disc Drive Module
57
1.
Remove two screw securing the HDD bracket.
2.
Remove the other two screw on the other side.
3.
Take out the HDD from the HDD bracket.
Chapter 3
Removing the Optical Disc Drive Module
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Hard Disc Drive Module” on page 57.
3.
Remove the screw securing the optical disc drove (ODD) module.
4.
Push the ODD module outwards with a flat headed screw driver.
5.
Then remove the ODD module.
Disassembling the Optical Disc Drive Module
1.
Remove two screws securing the ODD bracket.
2.
Then remove the ODD bracket.
Chapter 3
58
Removing the Memory
59
1.
See “Removing the Battery” on page 56.
2.
Remove the two screws securing the DIMM cover then remove the DIMM cover.
3.
Pop out the memory.
4.
Then remove the memory from the DIMM socket.
Chapter 3
Removing the LCD Module
Removing the Middle Cover
1.
See “Removing the Battery” on page 56.
2.
Open the notebook as image shows.
3.
Detach the middle cover carefully then remove it.
Removing the Keyboard
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Middle Cover” on page 60.
3.
Remove the four screws securing the keyboard.
4.
Turn the keyboard over as shown.
5.
Disconnect the keyboard cable then remove the keyboard.
Removing the Fan, the CPU Thermal Module and the CPU
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Middle Cover” on page 60.
3.
See “Removing the Keyboard” on page 60.
4.
Remove the three screws securing the system fan.
5.
Disconnect the fan cable.
6.
Then detach the fan from the main unit.
Chapter 3
60
7.
Remove the four screws securing the CPU thermal module.
8.
Then remove the CPU thermal module.
NOTE: Please remove the screws in the order that the image indicates. Start from 4, 3, 2 then 1. When you
reassemble the CPU thermal module, secure the screws as the order: 1, 2, 3 then 4. This can help you
average the force to each screw, therefore the CPU module can be secured well.
9.
Release the CPU lock with a flat headed screw driver.
10. Then detch the CPU from the socket carefully.
Removing the Wireless LAN Card
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Middle Cover” on page 60.
3.
Pop out the wireless LAN card.
4.
Disconnect the main and the auxiliary antennae.
5.
Then remove the wireless LAN card from the main unit.
Removing the LCD Module
61
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Middle Cover” on page 60.
3.
See “Removing the Keyboard” on page 60.
4.
Disconnect the inverter cable with a flat headed screw driver.
5.
Take out the LVDS cable then disconnect the LVDS cable.
Chapter 3
6.
Tear off the tape securing the wireless LAN antennae then release the antennae.
7.
Remove the two screws securing the LCD module on the rear side.
8.
Remove the two screws securing the LCD module on the bottom.
9.
Then detach the LCD module carefully.
Chapter 3
62
Disassembling the LCD Module
Removing the LCD Bezel
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Middle Cover” on page 60.
3.
See “Removing the Keyboard” on page 60.
4.
See “Removing the Fan, the CPU Thermal Module and the CPU” on page 60.
5.
See “Removing the Wireless LAN Card” on page 61.
6.
See “Removing the LCD Module” on page 61.
7.
Detach the two rubber pads and the two screw pads.
8.
Remove the four screws securing the LCD bezel.
9.
Detach the LCD bezel carefully.
10. Remove the nine screws securing the LCD to the LCD panel.
11. Take out the LCD assembly from the LCD panel.
12. Disconnect the LCD inverter cable.
13. Discnnect the LCD inverter board.
14. Turn over the LCD.
15. Disconnect the LCD cable.
16. Remove the four screws securing the right LCD bracket, then remove the right bracket.
17. Remove the four screws securing the left LCD bracket, then remove the left bracket.
63
Chapter 3
Chapter 3
64
Disassembling the Main Unit
Removing the Upper Case Assembly
1.
See “Removing the Battery” on page 56..
2.
See “Removing the Hard Disc Drive Module” on page 57.
3.
See “Removing the Optical Disc Drive Module” on page 58.
4.
See “Removing the Memory” on page 59.
5.
See “Removing the LCD Module” on page 60.
6.
Remove the fifteen screws securing the lower case assembly and the upper case assembly on the
bottom.
7.
Remove the three screws securing the upper case assembly.
8.
Disconnect the touchpad cable.
9.
Disconnect the power board cable.
10. Then detach the upper case assembly.
Removing the Power Board
65
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Hard Disc Drive Module” on page 57.
3.
See “Removing the Optical Disc Drive Module” on page 58.
4.
See “Removing the Memory” on page 59.
5.
See “Removing the LCD Module” on page 60.
6.
Remove the two screws securing the power board.
7.
Tear off the tape holding the power board cable then remove the power board.
Chapter 3
Removing the Touchpad Bracket, the Touchpad Board and the Touchpad
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Middle Cover” on page 60.
3.
See “Removing the Keyboard” on page 60.
4.
See “Removing the Power Board” on page 65.
5.
See “Removing the Upper Case Assembly” on page 65.
6.
Pull back the tape covering the touchpad FFC.
7.
Disconnect the touchpad FFC the remove it.
8.
Remove the four screws securing the touchpad bracket.
9.
Slide the touchpad bracket back as shown.
10. Then remove the touchpad bracket.
11. Use a flat headed screw driver to detach the touchpad board.
12. Then detach the touchpad carefully.
Chapter 3
66
Removing the Speaker Set
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Middle Cover” on page 60.
3.
See “Removing the Keyboard” on page 60.
4.
See “Removing the Power Board” on page 65.
5.
See “Removing the Upper Case Assembly” on page 65.
6.
Disconnect the SW DJ board cable.
7.
Disconnect the CIR receiver cable.
8.
Then disconnect the audio board FFC cable.
9.
Disconnect the speaker set cable.
10. Then detach the speaker set from the lower case.
Removing the SW DJ Board Assembly
67
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Middle Cover” on page 60.
3.
See “Removing the Keyboard” on page 60.
4.
See “Removing the Power Board” on page 65.
5.
See “Removing the Upper Case Assembly” on page 65.
6.
See “Removing the Speaker Set” on page 67.
7.
Remove the two screws securing the SW DJ board assembly.
Chapter 3
8.
Remove the SW DJ board assembly from the lower case.
9.
Remove the two screws securing the SW DJ board and SW DJ board bracket.
10. Then remove the SW DJ board.
Removing the Audio Board
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Middle Cover” on page 60.
3.
See “Removing the Keyboard” on page 60.
4.
See “Removing the Power Board” on page 65.
5.
See “Removing the Upper Case Assembly” on page 65.
6.
See “Removing the Speaker Set” on page 67.
7.
See “Removing the SW DJ Board Assembly” on page 67.
8.
Remove the screw securing the audio board.
9.
Detach the audio board FFC.
10. Release the CIR receiver cable.
11. Then detach the audio board.
Removing the VGA Thermal Module
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Middle Cover” on page 60.
3.
See “Removing the Keyboard” on page 60.
Chapter 3
68
4.
See “Removing the Power Board” on page 65.
5.
See “Removing the Upper Case Assembly” on page 65.
6.
Remove the three screws securing the VGA thermal module.
7.
Then detach the VGA thermal module.
Removing the Modem Board
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Middle Cover” on page 60.
3.
See “Removing the Keyboard” on page 60.
4.
See “Removing the Power Board” on page 65.
5.
See “Removing the Upper Case Assembly” on page 65.
6.
Remove the two screws securing the modem board.
7.
Disconnect the modem board connector.
8.
Disconnect the modem board cable then remove the board.
Removing the Main Board
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Middle Cover” on page 60.
3.
See “Removing the Keyboard” on page 60.
4.
See “Removing the Power Board” on page 65.
5.
See “Removing the Upper Case Assembly” on page 65.
6.
See “Removing the Speaker Set” on page 67.
7.
See “Removing the SW DJ Board Assembly” on page 67.
8.
See “Removing the Audio Board” on page 68.
9.
See “Removing the VGA Thermal Module” on page 68.
10. See “Removing the Modem Board” on page 69.
11. Remove the two nut screws securing the main board.
12. Press the PCMCIA card button.
69
Chapter 3
13. Remove the dummy card.
14. Remove the two screws securing the main board to the lower case.
15. Then detach the main board from the lower case carefully.
Removing the Control Board
1.
See “Removing the Battery” on page 56.
2.
See “Removing the Middle Cover” on page 60.
3.
See “Removing the Keyboard” on page 60.
4.
See “Removing the Power Board” on page 65.
5.
See “Removing the Upper Case Assembly” on page 65.
6.
See “Removing the Speaker Set” on page 67.
7.
See “Removing the SW DJ Board Assembly” on page 67.
8.
See “Removing the Audio Board” on page 68.
9.
See “Removing the VGA Thermal Module” on page 68.
10. See “Removing the Modem Board” on page 69.
11. See “Removing the Main Board” on page 69.
12. Turn over the main board as shown.
13. Disconnect the control board antenna.
14. Pop out the control board then remove it.
Chapter 3
70
71
Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1.
Obtain the failing symptoms in as much detail as possible.
2.
Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power failure. (The power indicator does not go
on or stay on.)
“Power System Check” on page 74.
POST does not complete. No beep or error
codes are indicated.
“Power-On Self-Test (POST) Error Message” on
page 77
“Undetermined Problems” on page 89
POST detects an error and displayed messages
on screen.
“Error Message List” on page 78
Other symptoms (i.e. LCD display problems or
others).
“Power-On Self-Test (POST) Error Message” on
page 77
Symptoms cannot be re-created (intermittent
problems).
Use the customer-reported symptoms and go to
“Power-On Self-Test (POST) Error Message” on
page 77
“Intermittent Problems” on page 88
“Undetermined Problems” on page 89
Chapter 4
72
System Check Procedures
External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is
required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause
damage to the drive or cause the drive to fail.
Do the following to select the test device.
1.
Boot from the diagnostics diskette and start the diagnostics program.
2.
See if FDD Test is passed as the program runs to FDD Test.
3.
Follow the instructions in the message window.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1.
Reconnect the external diskette drive/DVD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1.
Boot from the diagnostics diskette and start the diagnostics program.
2.
See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3.
Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1.
Reconnect the external diskette drive/CD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the keyboard cables.
2.
Replace the keyboard.
3.
Replace the main board.
The following auxiliary input devices are supported by this computer:
T
Numeric keypad
T
External keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
73
Chapter 4
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.
Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2.
Go to the diagnostic memory in the test items.
3.
Press F2 in the test items.
4. Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1.
Remove the battery pack.
2.
Connect the power adapter and check that power is supplied.
3.
Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
Chapter 4
T
“Check the Power Adapter” on page 75
T
“Check the Battery Pack” on page 76
74
Check the Power Adapter
Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power
adapter cable. See the following figure
Pin 1: +19 to +20.5V
Pin 2: 0V, Ground
1.
If the voltage is not correct, replace the power adapter.
2.
If the voltage is within the range, do the following:
T
Replace the System board.
T
If the problem is not corrected, see “Undetermined Problems” on page 89.
T
If the voltage is not correct, go to the next step.
NOTE: An audible noise from the power adapter does not always indicate a defect.
75
3.
If the power-on indicator does not light up, check the power cord of the power adapter for correct
continuity and installation.
4.
If the operational charge does not work, see “Check the Battery Pack” on page 76.
Chapter 4
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1.
Check out the Power Management in control Panel
2.
In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3.
Repeat the steps 1 and 2, for both battery and adapter.
4.
This helps you identify first the problem is on recharging or discharging.
From Hardware:
1.
Power off the computer.
2.
Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground).
3.
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light
up, replace the DC/DC charger board.
Touchpad Check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the touchpad cables.
2.
Replace the touchpad.
3.
Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
Chapter 4
76
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 89.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
77
Chapter 4
Index of Error Messages
Error Code List
Error Codes
006
Error Messages
Equipment Configuration Error
Causes:
1. CPU BIOS Update Code Mismatch
2. IDE Primary Channel Master Drive Error
(THe causes will be shown before “Equipment Configuration
Error”)
010
Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)
070
Real Time Clock Error
071
CMOS Battery Bad
072
CMOS Checksum Error
110
System disabled.
Incorrect password is specified.
<No error code>
Battery critical LOW
In this situation BIOS will issue 4 short beeps then shut down
system, no message will show.
<No error code>
Thermal critical High
In this situation BIOS will shut down system, not show message.
Error Message List
Error Messages
Failure Fixed Disk
FRU/Action in Sequence
Reconnect hard disk drive connector.
“Load Default Settings” in BIOS Setup Utility.
Hard disk drive
System board
Stuck Key
see “Keyboard or Auxiliary Input Device Check” on page 73.
Keyboard error
see “Keyboard or Auxiliary Input Device Check” on page 73.
Keyboard Controller Failed
see “Keyboard or Auxiliary Input Device Check” on page 73.
Keyboard locked - Unlock key switch
Unlock external keyboard
Monitor type does not match CMOS - Run Setup Run “Load Default Settings” in BIOS Setup Utility.
Shadow RAM Failed at offset: nnnn
BIOS ROM
System board
System RAM Failed at offset: nnnn
DIMM
System board
Extended RAM Failed at offset: nnnn
DIMM
System board
System battery is dead - Replace and run Setup
Replace RTC battery and Run BIOS Setup Utility to reconfigure
system time, then reboot system.
System CMOS checksum bad - Default
configuration used
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System timer error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board
Chapter 4
78
Error Message List
Error Messages
79
FRU/Action in Sequence
Real time clock error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board
Previous boot incomplete - Default configuration
used
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Memory size found by POST differed from
CMOS
Run “Load Default Settings” in BIOS Setup Utility.
DIMM
System board
Diskette drive A error
Check the drive is defined with the proper diskette type in BIOS
Setup Utility
See “External Diskette Drive Check” on page 73.
Incorrect Drive A type - run SETUP
Check the drive is defined with the proper diskette type in BIOS
Setup Utility
System cache error - Cache disabled
System board
CPU ID:
System board
DMA Test Failed
DIMM
System board
Software NMI Failed
DIMM
System board
Fail-Safe Timer NMI Failed
DIMM
System board
Device Address Conflict
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Allocation Error for device
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Failing Bits: nnnn
DIMM
BIOS ROM
System board
Fixed Disk n
None
Invalid System Configuration Data
BIOS ROM
System board
I/O device IRQ conflict
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Operating system not found
Enter Setup and see if fixed disk and drive A: are properly identified.
Diskette drive
Hard disk drive
System board
Chapter 4
Error Message List
No beep Error Messages
FRU/Action in Sequence
No beep, power-on indicator turns off and LCD is
blank.
Power source (battery pack and power adapter). See “Power
System Check” on page 74.
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
LED board.
System board.
No beep, power-on indicator turns on and LCD is
blank.
Power source (battery pack and power adapter). See “Power
System Check” on page 74.
Reconnect the LCD connector
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board
No beep, power-on indicator turns on and LCD is
blank. But you can see POST on an external
CRT.
Reconnect the LCD connectors.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
No beep, power-on indicator turns on and a
blinking cursor shown on LCD during POST.
Ensure every connector is connected tightly and correctly.
System board
No beep during POST but system runs correctly.
Speaker
System board
Chapter 4
80
Phoenix BIOS Beep Codes
Code
Beeps
Verify Real Mode
03h
Disable Non-Maskable Interrupt (NMI)
04h
Get CPU type
06h
Initialize system hardware
08h
Initialize chipset with initial POST values
09h
Set IN POST flag
0Ah
Initialize CPU registers
0Bh
Enable CPU cache
0Ch
Initialize caches to initial POST values
0Eh
Initialize I/O component
0Fh
Initialize the local bus IDE
10h
Initialize Power Management
11h
Load alternate registers with initial POST
values
12h
Restore CPU control word during warm boot
13h
Initialize PCI Bus Mastering devices
14h
Initialize keyboard controller
16h
1-2-2-3
17h
BIOS ROM checksum
Initialize cache before memory autosize
18h
8254 timer initialization
1Ah
8237 DMA controller initialization
1Ch
Reset Programmable Interrupt Controller
20h
1-3-1-1
Test DRAM refresh
22h
1-3-1-3
Test 8742 Keyboard Controller
24h
Set ES segment register to 4 GB
26h
Enable A20 line
28h
Autosize DRAM
29h
Initialize POST Memory Manager
2Ah
Clear 215 KB base RAM
2Ch
1-3-4-1
RAM failure on address line xxxx
2Eh
1-3-4-3
RAM failure on data bits xxxx of low byte of
memory bus
2Fh
30h
Enable cache before system BIOS shadow
1-4-1-1
RAM failure on data bits xxxx of high byte of
memory bus
32h
Test CPU bus-clock frequency
33h
Initialize Phoenix Dispatch Manager
36h
Warm start shut down
38h
Shadow system BIOS ROM
3Ah
Autosize cache
3Ch
Advanced configuration of chipset registers
3Dh
Load alternate registers with CMOS values
42h
Initialize interrupt vectors
45h
46h
81
POST Routine Description
02h
POST device initialization
2-1-2-3
Check ROM copyright notice
Chapter 4
Code
Beeps
POST Routine Description
48h
Check video configuration against CMOS
49h
Initialize PCI bus and devices
4Ah
Initialize all video adapters in system
4Bh
QuietBoot start (optional)
4Ch
Shadow video BIOS ROM
4Eh
Display BIOS copyright notice
50h
Display CPU type and speed
51h
Initialize EISA board
52h
Test keyboard
54h
Set key click if enabled
58h
59h
2-2-3-1
Test for unexpected interrupts
Initialize POST display service
5Ah
Display prompt “Press F2 to enter SETUP”
5Bh
Disable CPU cache
5Ch
Test RAM between 512 and 640 KB
60h
Test extended memory
62h
Test extended memory address lines
64h
Jump to User Patch1
66h
Configure advanced cache registers
67h
Initialize Multi Processor APIC
68h
Enable external and CPU caches
69h
Setup System Management Mode (SMM) area
6Ah
Display external L2 cache size
6Bh
Load custom defaults (optional)
6Ch
Display shadow-area message
6Eh
Display possible high address for UMB
recovery
70h
Display error messages
72h
Check for configuration errors
76h
Check for keyboard errors
7Ch
Set up hardware interrupt vectors
7Eh
Initialize coprocessor if present
80h
Disable onboard Super I/O ports and IRQs
81h
Late POST device initialization
82h
Detect and install external RS232 ports
83h
Configure non-MCD IDE controllers
84h
Detect and install external parallel ports
85h
Initialize PC-compatible PnP ISA devices
86h
Re-initialize onboard I/O ports
87h
Configure Motherboard Configurable Devices
(optional)
88h
Initialize BIOS Area
89h
Enable Non-Maskable Interrupts (NMIs)
8Ah
Initialize Extended BIOS Data Area
8Bh
Test and initialize PS/2 mouse
8Ch
Initialize floppy controller
Chapter 4
82
Code
Beeps
8Fh
Determine number of ATA drives (optional)
90h
Initialize hard-disk controllers
91h
Initialize local-bus hard-disk controllers
92h
Jump to UserPatch2
93h
Build MPTABLE for multi-processor boards
95h
Install CD ROM for boot
96h
Clear huge ES segment register
97h
Fixup Multi Processor table
98h
1-2
Search for option ROMs. One long, two short
beeps on checksum failure.
99h
Check for SMART drive (optional)
9Ah
Shadow option ROMs
9Ch
Set up Power Management
9Dh
Initialize security engine (optional)
9Eh
Enable hardware interrupts
9Fh
Determine number of ATA and SCSI drives
A0h
Set time of day
A2h
Check key lock
A4h
Initialize Typematic rate
A8h
Erase F2 prompt
AAh
Scan for F2 key stroke
ACh
Enter SETUP
AEh
Clear Boot flag
B0h
Check for errors
B2h
B4h
83
POST Routine Description
POST done- prepare to boot operating system
1
One short beep before boot
B5h
Terminate QuietBoot (optional)
B6h
Check password (optional)
B9h
Prepare Boot
BAh
Initialize DMI parameters
BBh
Initialize PnP Option ROMs
BCh
Clear parity checkers
BDh
Display MultiBoot menu
BEh
Clear screen (optional)
BFh
Check virus and backup reminders
C0h
Try to boot with INT 19
C1h
Initialize POST Error Manager (PEM)
C2h
Initialize error logging
C3h
Initialize error display function
C4h
Initialize system error handler
C5h
PnPnd dual CMOS (optional)
C6h
Initialize notebook docking (optional)
C7h
Initialize notebook docking late
C8h
Force check (optional)
C9h
Extended checksum (optional)
D2h
Unknown interrupt
Chapter 4
Code
Beeps
E0h
Initialize the chipset
E1h
Initialize the bridge
E2h
Initialize the CPU
E3h
Initialize the system timer
E4h
Initialize system I/O
E5h
Check force recovery boot
E6h
Checksum BIOS ROM
E7h
Go to BIOS
E8h
Set Huge Segment
E9h
Initialize Multi Processor
EAh
Initialize OEM special code
EBh
Initialize PIC and DMA
ECh
Initialize Memory type
EDh
Initialize Memory size
EEh
Shadow Boot Block
EFh
System memory test
F0h
Initialize interrupt vectors
F1h
Initialize Run Time Clock
F2h
Initialize video
F3h
F4h
Initialize System Management Mode
1
Output one beep before boot
F5h
Boot to Mini DOS
F6h
Clear Huge Segment
F7h
Boot to Full DOS
Chapter 4
84
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
Action in Sequence
LCD backlight doesn't work
LCD is too dark
LCD brightness cannot be adjusted
LCD contrast cannot be adjusted
Enter BIOS Utility to execute “Load Setup Default Settings”, then
reboot system.
Reconnect the LCD connectors.
Keyboard (if contrast and brightness function key doesn't work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Unreadable LCD screen
Missing pels in characters
Abnormal screen
Wrong color displayed
Reconnect the LCD connector
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
LCD has extra horizontal or vertical lines
displayed.
LCD inverter ID
LCD inverter
LCD cable
LCD
System board
Indicator-Related Symptoms
Symptom / Error
Indicator incorrectly remains off or on, but system
runs correctly
Action in Sequence
Reconnect the inverter board
Inverter board
System board
Power-Related Symptoms
Symptom / Error
85
Action in Sequence
Power shuts down during operation
Power source (battery pack and power adapter). See “Power
System Check” on page 74.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-on.
Power source (battery pack and power adapter). See “Power
System Check” on page 74.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-off.
Power source (battery pack and power adapter). See “Power
System Check” on page 74.
Hold and press the power switch for more than 4 seconds.
System board
Battery can’t be charged
See “Check the Battery Pack” on page 76.
Battery pack
System board
Chapter 4
PCMCIA-Related Symptoms
Symptom / Error
Action in Sequence
System cannot detect the PC Card (PCMCIA)
PCMCIA slot assembly
System board
PCMCIA slot pin is damaged.
PCMCIA slot assembly
Memory-Related Symptoms
Symptom / Error
Memory count (size) appears different from
actual size.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings, then
reboot system.
DIMM
System board
Speaker-Related Symptoms
Symptom / Error
Action in Sequence
In Windows, multimedia programs, no sound
comes from the computer.
Audio driver
Speaker
System board
Internal speakers make noise or emit no sound.
Speaker
System board
Power Management-Related Symptoms
Symptom / Error
Action in Sequence
The system will not enter hibernation
Keyboard (if control is from the keyboard)
Hard disk drive
System board
The system doesn't enter hibernation mode and
four short beeps every minute.
See “S4 Sleeping State” on page 36.
Press Fn+oand see if the computer enters hibernation mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board
The system doesn’t enter standby mode after
closing the LCD
See “S4 Sleeping State” on page 36.
LCD cover switch
System board
The system doesn't resume from hibernation
mode.
See “S4 Sleeping State” on page 36.
Hard disk connection board
Hard disk drive
System board
The system doesn't resume from standby mode
after opening the LCD.
See “S4 Sleeping State” on page 36.
LCD cover switch
System board
Battery fuel gauge in Windows doesn’t go higher
than 90%.
Remove battery pack and let it cool for 2 hours.
Refresh battery (continue use battery until power off, then charge
battery).
Battery pack
System board
Chapter 4
86
Power Management-Related Symptoms
Symptom / Error
System hangs intermittently.
Action in Sequence
Reconnect hard disk/CD-ROM drives.
Hard disk connection board
System board
Peripheral-Related Symptoms
Symptom / Error
Action in Sequence
System configuration does not match the
installed devices.
Enter BIOS Setup Utility to execute “Load Default Settings”, then
reboot system.
Reconnect hard disk/CD-ROM/diskette drives.
External display does not work correctly.
Press Fn+F5, LCD/CRT/Both display switching
System board
USB does not work correctly
System board
Print problems.
Ensure the “Parallel Port” in the “Onboard Devices Configuration” of
BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Serial or parallel port device problems.
Ensure the “Serial Port” in the Devices Configuration” of BIOS Setup
Utility is set to Enabled.
Device driver
Device cable
Device
System board
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Action in Sequence
Keyboard (one or more keys) does not work.
Reconnect the keyboard cable.
Keyboard
System board
Touchpad does not work.
Reconnect touchpad cable.
Touchpad board
System board
Modem-Related Symptoms
Symptom / Error
Internal modem does not work correctly.
Action in Sequence
Modem phone port
modem combo board
System board
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
Problems” on page 89.
87
Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.
Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
88
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 74):
89
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
T
Non-Acer devices
T
Printer, mouse, and other external devices
T
Battery pack
T
Hard disk drive
T
DIMM
T
CD-ROM/Diskette drive Module
T
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
T
System board
T
LCD assembly
Chapter 4
Chapter 5
Jumper and Connector Locations
Top View
Chapter 5
90
Bottom View
91
1
SW1
Lid Switch
2
CN1
LCD Connector
3
CN2
Launch Board Connector
4
CN3
Modem Connector
5
CN7
Keyboard Connector
6
CN4
Bluetooth Module Connector
7
CN5
Touchpad Board Connector
8
CN6
Internal Microphone Connector
9
U17
Clock Generator
10
U4
PCMCIA Connector
11
CN9
MDC Connector
12
CN11
Internal Speaker Connector
13
CN13
Power Jack
14
CN12
CRT Connector
15
CN14
Battery Connector
16
CN15
Optical Disk Drive Connector
17
CN17
RJ45 & RJ11 Connector
18
CN26
Wireless LAN Controller
19
U11
North Bridge
20
U13
CPU Socket
21
CN20
USB Connector
22
CN21
USB Connector
23
U19
BIOS ROM
24
U4
EC PC97551 (Power and I/O
Connector)
25
CN22
RTC Battery
26
CN18
Memory Socket 1
27
U1
LAN Chipset RTL8100CL
28
CN19
Memory Socket 2
Chapter 5
29
U18
South Bridge
31
CN25
HDD Connector
32
CN27
USB Connector
33
CN28
Line-out/SPEDIF Jack
34
CN29
Microphone Jack
35
CN30
Line-in Jack
36
SW3
WLAN Button
37
SW2
Bluetooth Button
38
LED2
Charger LED
39
LED1
Power LED
40
U22
Audio Codec
41
U10
Fan Connector
Chapter 5
30
CN24
PCMCIA Connector
92
93
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of TravelMate 4070/
4080. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise
Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available
on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on
the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use
the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer
machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to
return it.
Chapter 6
94
TravelMate 4070/4080 Exploded Diagram
TravelMate 4070/4080 FRU List
Adapter
NS
ADP 19V 3.42A PA-1650-02QR
90~264V LF
AP.06503.010
NS
ADP 19V 3.42A SLS0335A19A57LF
90~264V EU
AP.06506.002
NS
ADP 19V 3.42A SADP-65KB DBHF
90~264V LF
AP.06501.009
Battery
95
Chapter 6
TravelMate 4070/4080 FRU List
NS
BATTERY SANYO LI-ION 4S2P 4.4A
4UR18650F-2-QC140
BT.T5003.001
BATTERY PANASONIC LI-ION 4S2P
4.4A CGR-B/8B5AE
BT.T5005.001
BATTERY PANASONIC LI-ION 4S2P
4.4A ROHS
BT.00805.003
BATTERY SIMPPLO PACK LI-ION
4S1P 2.0A
BT.00407.001
BATTERY SANYO PACK LI-ION
4S1P 2.0A
BT.00403.004
BATTERY SONY PACK LI-ION 4S1P
1.96A
BT.00404.004
NS
MODEM 56K (MDC)T60M845.02 EU
54.TAKV7.001
NS
BLUETOOTH MODULE W/ANTENNA
54.T48V7.001
NS
W/L 802.11B/G(WM3B2200BGMW2)
KI.CAX01.008
NS
LAUNCH BOARD
55.TAKV7.001
NS
TOUCH PAD BOARD
55.TAKV7.002
NS
FFC CABLE - TP/B TO MB
50.T50V7.001
Board
Cable
Chapter 6
96
TravelMate 4070/4080 FRU List
NS
MODEM CABLE
50.A510V7.001
NS
POWER CORD US (3 PIN)
27.A03V7.001
POWER CORD PRC (3 PIN)
27.A03V7.003
POWER CORD KOERA ( Pin)
27.T23V7.006
POWER CORD EU (3 PIN)
27.A03V7.002
POWER CORD UK (3 PIN)
27.A03V7.004
POWER CORD ITALIAN (3 PIN)
27.A03V7.005
POWER CORD- SWISS
27.A03V7.007
POWER CORD AU (3 PIN)
27.A03V7.008
POWER CORD DANISH (3 PIN)
27.A03V7.006
POWER CORD AF (3 PIN)
27.T48V7.001
5
MIDDEL COVER ERGO W/BUTTON LIGHT GREEN SILVER
42.T50V7.101
6
UPPER CASE W/TOUCHPAD,
BRACKET, MIC,BLUETOOTH CABLE
60.T91V7.001
UPPER CASE W/TOUCHPAD,
BRACKET, MIC W/O BLUETOOTH
CABLE
60.T91V7.002
11
LOWER CASE W/SPEAKER
60.A51V7.002
13
DIMM/WIRELESS COVER
42.A50V7.001
HEATSINK COVER W/O DOCKING
42.A50V7.002
Case/Cover/Bracket Assembly
97
Chapter 6
TravelMate 4070/4080 FRU List
NS
3 IN 1 DUMMY COVER
42.T51V7.003
15
HDD COVER
42.T63V7.004
14
HDD BRACKET
33.T50V7.001
NS
WIRELESS LAN ANTENNA
50.T50V7.003
NS
AMD MOBILE SEMPRON 2800+
25WD
KC.S2802.25D
AMD MOBILE SEMPRON 3000+
25WD
KC.S3002.25D
AMD MOBILE TURION 64 ML28
KC.TML02.280
AMD MOBILE TURION 64 ML30
KC.TML02.300
AMD MOBILE TURION 64 ML32
KC.TML02.320
AMD MOBILE TURION 64 ML34
KC.TML02.340
AMD MOBILE TURION 64 ML37
KC.TML02.370
DVD/CDRW COMBO MODULE 24X
PHILIPS SCB5265 LF
6M.A65V7.004
Communication Module
CPU/Processor
Optical Disk Drive Module
NS
Chapter 6
98
TravelMate 4070/4080 FRU List
99
NS
DVD/CDRW COMBO DRIVE 24X
PHILIPS SCB5265 GB LF
KO.02403.007
NS
OPTICAL DEVICE HOLDER-FIX
42.T51V7.003
NS
DVD/CDRW BEZEL FOR G BASE
42.A65V7.003
DVD/CDRW COMBO MODULE KME
UJDA-770
6M.TAGV7.002
DVD/CDRW COMBO DRIVE 24X
KME UJDA-770
KO.02406.013
OPTICAL DEVICE HOLDER-FIX
42.T51V7.003
DVD/CDRW BEZEL FOR G BASE
42.A65V7.003
DVD/CDRW COMBO MODULE LITEON SOSC-2483K LF
6M.ATKV7.001
DVD/CDRW COMBO LITE-ON
SOSC-2483K LF GB
KO.02409.011
OPTICAL DEVICE HOLDER-FIX
42.T51V7.003
DVD/CDRW BEZEL FOR G BASE
42.A65V7.003
DVD/CDRW COMBO MODULE HLDS
GCC-4244N LF
6M.ATKV7.002
DVD/CDRW COMBO HLDS GCC4244N GB LF
KO.0240A.004
OPTICAL DEVICE HOLDER-FIX
42.T51V7.003
DVD DUAL BEZEL G BASE
42.A65V7.003
DVD DUAL MODULE PANASONIC
UJ-840BAA2 G BASE
6M.A51V7.003
DVD DUAL DRIVE PANASONIC UJ840BAA2 D. LAYER G BASE
KU.00807.010
OPTICAL DEVICE HOLDER-FIX
42.T51V7.003
DVD DUAL BEZEL G BASE
42.A51V7.005
DVD DUAL MODULE LITE-ON
SOSW-833 DL G BASE
6M.T66V5.003
Chapter 6
TravelMate 4070/4080 FRU List
DVD DUAL DRIVE LIET-ON SOSW833 DL G BASE
KU.00804.012
OPTICAL DEVICE HOLDER-FIX
42.T51V7.003
DVD DUAL BEZEL G BASE
42.A51V7.005
DVD DUAL MODULE PIONEER DVRK15RA F/W:1.05 G BASE
6M.ATKV7.003
DVD DUAL DRIVEPIONEER DVRK15RA D. LAYER F/W:1.05 G BASE
KU.00805.020
OPTICAL DEVICE HOLDER-FIX
42.T51V7.003
DVD DUAL BEZEL G BASE
42.A51V7.005
DVD DUAL MODULE HLDS GWA4082N G BASE
6M.ATKV7.004
DVD DUAL DRIVE HLDS GWA4082N G BASE
KU.0080D.016
OPTICAL DEVICE HOLDER-FIX
42.T51V7.003
DVD DUAL BEZEL G BASE
42.A51V7.005
40G SEAGATE 2.5 IN. 4200RPM
N2.1ST9402113A (ROHS), F/W 3.01
KH.04001.016
40G TOSHIBA 2.5 IN. 4200RPM
PLUTO MK4025GAS (ROHS) F/W
KA100A
KH.04004.005
40G HGST 2.5 IN. 4200RPM
HAKONA-A F/W :A70G
KH.04007.013
40G WD 2.5 IN. 5400RPM ML40
WD400UE-22HCT0 (ROHS)
KH.04008.025
40G SAMSUNG 2.5 IN. 5400RPM
M40MP0402H (ROHS) F/W YQ20004
KH.0400B.003
60G SEAGATE 2.5 IN. 4200RPM
N2.2ST960812A F/W:3.04
KH.06001.003
60G TOSHIBA 2.5 IN. 4200RPM
PLUTO MK6025GAS (ROHS) F/W
KA200
KH.06004.004
60G HGST 2.5 IN. 4200RPM
HAKONE-A F/W :A70G
KH.06007.009
60G WD 2.5 IN. 5400RPM ML40
WD600UE-22HCT0 (ROHS)
KH.06008.002
80G SEAGATE 2.5 IN. 4200RPM
N2.2ST980829A F/W:3.04
KH.08001.013
80G TOSHIBA 2.5 IN. 4200RPM
PLUTO MK8025GAS (ROHS) F/W
KA023
KH.08004.003
HDD/Hard Disk Drive
NS
Chapter 6
100
TravelMate 4070/4080 FRU List
80G HGST 2.5 IN. 4200RPM
HAKONE-A F/W:A70G
KH.08007.011
80G WD 2.5 IN. 5400RPM ML40
WD800UE-22HCT0 (ROHS)
KH.08008.027
100G TOSHIBA 2.5 IN. 4200RPM
ARES MK1031GAS (ROHS) F/W
AA204A
KH.10004.001
100G HGST 2.5 IN. 4200RPM
HAKONE-A F/W:A70G
KH.10007.002
AS1680/AS1410 KEYBOARD
DARFON US International
KB.A2707.001
AS1680/AS1410 KEYBOARD
DARFON Chinese
KB.A2707.002
AS1680/AS1410 KEYBOARD
DARFON Spanish
KB.A2707.003
AS1680/AS1410 KEYBOARD
DARFON Thai
KB.A2707.004
AS1680/AS1410 KEYBOARD
DARFON Brazilian Protugese
KB.A2707.005
AS1680/AS1410 KEYBOARD
DARFON Korea
KB.A2707.006
AS1680/AS1410 KEYBOARD
DARFON UK
KB.A2707.007
AS1680/AS1410 KEYBOARD
DARFON German
KB.A2707.008
AS1680/AS1410 KEYBOARD
DARFON Italian
KB.A2707.009
AS1680/AS1410 KEYBOARD
DARFON French
KB.A2707.010
AS1680/AS1410 KEYBOARD
DARFON Swiss/G
KB.A2707.011
AS1680/AS1410 KEYBOARD
DARFON Portuguese
KB.A2707.012
AS1680/AS1410 KEYBOARD
DARFON Arabic
KB.A2707.013
AS1680/AS1410 KEYBOARD
DARFON Belgium
KB.A2707.014
AS1680/AS1410 KEYBOARD
DARFON Sweden
KB.A2707.015
AS1680/AS1410 KEYBOARD
DARFON Czech
KB.A2707.016
AS1680/AS1410 KEYBOARD
DARFON Hungaian
KB.A2707.017
AS1680/AS1410 KEYBOARD
DARFON Norway
KB.A2707.018
AS1680/AS1410 KEYBOARD
DARFON Danish
KB.A2707.019
AS1680/AS1410 KEYBOARD
DARFON Turkish
KB.A2707.020
Keyboard
NS
101
Chapter 6
TravelMate 4070/4080 FRU List
AS1680/AS1410 KEYBOARD
DARFON Canadian French
KB.A2707.021
AS1680/AS1410 KEYBOARD
DARFON Japanese
KB.A2707.022
AS1680/AS1410 KEYBOARD
DARFON Greek
KB.A2707.023
AS1680/AS1410 KEYBOARD
DARFON Hebrew
KB.A2707.024
AS1680/AS1410 KEYBOARD
DARFON Russian
KB.A2707.025
NS
LCD 15.0 IN. MODULE SAMSUNG
LTN150XB-L03-V LF
6M.ATKV7.011
NS
LCD 15.0 IN. XGA SAMSUNG
LTN150XB-L03-V LF
LK.15006.008
NS
LCD INVERTER BOARD
19.TAKV7.001
NS
LCD CABLE - 15 IN. XGA
50.T50V7.004
NS
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
LCD Module
Chapter 6
102
TravelMate 4070/4080 FRU List
103
NS
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
NS
LCD PANEL W/LOGO ANTENNA 14/
15 IN.
60.T50V7.102
NS
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD 15.0 IN. MODULE CMO N150X3L07 LF
6M.ATKV7.012
LCD 15.0 IN. XGA CMO N150X3-L07
REV C4 LF
LK.1500D.012
NS
LCD INVERTER BOARD
19.TAKV7.001
NS
LCD CABLE - 15 IN. XGA
50.T50V7.004
NS
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
NS
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
NS
LCD PANEL W/LOGO ANTENNA 14/
15 IN.
60.T50V7.102
NS
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD 15.0 IN. MODULE LPL
LP150X07-TLA2 LF
6M.ATKV7.013
LCD 15.0 IN. XGA LPL LP150X07TLA2 LF
LK.15008.019
NS
LCD INVERTER BOARD
19.TAKV7.001
NS
LCD CABLE - 15 IN. XGA
50.T50V7.004
NS
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
NS
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
NS
LCD PANEL W/LOGO ANTENNA 14/
15 IN.
60.T50V7.102
NS
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD 15.0 IN. MODULE LPL
LP150X07-TLA2 LF
6M.ATKV7.013
Chapter 6
TravelMate 4070/4080 FRU List
Chapter 6
LCD 15.0 IN. XGA LPL LP150X07TLA2 LF
LK.15008.019
LCD INVERTER BOARD
19.TAKV7.001
LCD CABLE - 15 IN. XGA
50.T50V7.004
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
LCD PANEL W/LOGO ANTENNA 14/
15 IN.
60.T50V7.102
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
NS
LCD MODULE 15.4 IN. WXGA CMO
N154I1-L09
6M.A51V7.013
NS
LCD 15.4 IN. WXGA CMO N154I1L09
LK.1540D.002
NS
LCD INVERTER BOARD
19.TAKV7.001
NS
LCD CABLE - 15.4 IN. XGA
50.T50V7.006
2
LCD BRACKET W/HINGE 15.4 IN. - L
33.T50V7.004
3
LCD BRACKET W/HINGE 15.4 IN. - R
33.T50V7.005
4
LCD PANEL W/LOGO ANTENNA 14/
15 IN.
60.T50V7.102
1
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
LCD 15.4 MODULE SAMSUNG
LTN154X3-L01-V104
6M.ATKV7.014
LCD 15.4 WXGA SAMSUNG
LTN154X3-L01-V104
LK.15406.009
LCD INVERTER BOARD
19.TAKV7.001
LCD CABLE - 15.4 IN. WXGA
50.T50V7.006
LCD BRACKET W/HINGE 15.4 IN. - L
33.T50V7.004
LCD BRACKET W/HINGE 15.4 IN. - R
33.T50V7.005
LCD PANEL W/LOGO ANTENNA
15.4 IN.
60.T50V7.103
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
LCD 15.4 MODULE QDI QD15TL0203 LF NON-GLARE
6M.ATKV7.015
LCD 15.4 WXGA QDI QD15TL02-03
LF NON-GLARE
LK.15409.004
LCD INVERTER BOARD
19.TAKV7.014
LCD CABLE - 15.4 IN. WXGA
50.T50V7.006
LCD BRACKET W/HINGE 15.4 IN. - L
33.T50V7.004
LCD BRACKET W/HINGE 15.4 IN. - R
33.T50V7.005
LCD PANEL W/LOGO ANTENNA
15.4 IN.
60.T50V7.103
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
LCD 15.4 IN. MODULE AU
B154EW01 V8 LF NON-G
6M.ATKV7.016
104
TravelMate 4070/4080 FRU List
105
LCD 15.4 IN. WXGA AU B154EW01
V8 LF NON-G
LK.15405.005
LCD INVERTER BOARD
19.TAKV7.001
LCD CABLE - 15.4 IN. WXGA
50.T50V7.006
LCD BRACKET W/HINGE 15.4 IN. - L
33.T50V7.004
LCD BRACKET W/HINGE 15.4 IN. - R
33.T50V7.005
LCD PANEL W/LOGO ANTENNA
15.4 IN.
60.T50V7.103
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
LCD 15.0 IN. MODULE SAMSUNG
LTN150XB-L03-V W/O WIRELESS
6M.ATKV7.021
LCD 15.0 IN. XGA SAMSUNG
LTN150XB-L03-V LF
LK.15006.008
LCD INVERTER BOARD
19.TAKV7.001
LCD CABLE - 15 IN. XGA
50.T50V7.004
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
LCD PANEL W/LOGO W/O
ANTENNA 14/15 IN.
60.T56V7.102
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD 15.0 IN. MODULE CMO N150X3L07 LF W/O WIRELESS
6M.ATKV7.022
LCD 15.0 IN. XGA CMO N150X3-L07
REV C4 LF
LK.1500D.012
LCD INVERTER BOARD
19.TAKV7.001
LCD CABLE - 15 IN. XGA
50.T50V7.004
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
LCD PANEL W/LOGO W/O
ANTENNA 14/15 IN.
60.A56V7.102
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD 15.0 IN. MODULE LPL
LP150X07-TLA2 LF W/O WIRELESS
6M.ATKV7.023
LCD 15.0 IN. XGA LPL LP150X07TLA2 LF
LK.15008.019
LCD INVERTER BOARD
19.TAKV7.001
LCD CABLE - 15 IN. XGA
50.T50V7.004
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
LCD PANEL W/LOGO W/O
ANTENNA 14/15 IN.
60.A56V7.102
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD 15.4 MODULE QDI QD15TL0203 LF NON-GLARE W/O WIRELESS
6M.ATKV7.025
Chapter 6
TravelMate 4070/4080 FRU List
LCD 15.4 WXGA QDI QD15TL02-03
LF NON-GLARE
LK.15409.004
LCD INVERTER BOARD
19.TAKV7.001
LCD CABLE - 15.4 IN. WXGA
50.T50V7.006
LCD BRACKET W/HINGE 15.4 IN. - L
33.T50V7.004
LCD BRACKET W/HINGE 15.4 IN. - R
33.T50V7.005
LCD PANEL W/LOGO ANTENNA
15.4 IN.
60.T56V7.103
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
LCD 15.4 IN. MODULE AU
B154EW01 V8 LF NON-G W/O
WIRELESS
6M.ATKV7.026
LCD 15.4 IN. WXGA AU B154EW01
V8 LF NON-G
LK.15405.005
LCD INVERTER BOARD
19.TAKV7.001
LCD CABLE - 15.4 IN. WXGA
50.T50V7.006
LCD BRACKET W/HINGE 15.4 IN. - L
33.T50V7.004
LCD BRACKET W/HINGE 15.4 IN. - R
33.T50V7.005
LCD PANEL W/LOGO ANTENNA
15.4 IN.
60.T56V7.103
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
NS
MAINBOARD 915GM UMA W/
PCMCIA W/O CPU MEMORY
LB.TAK02.001
NS
MEMORY DDR333 256MB INFINEON
HYS64D32020HDL-6-C (.11u)
KN.25602.012
MEMORY DDR333 256MB NANYA
NT256D64SH8C0GM-6K
KN.25603.019
MEMORY DDR333 256MB
SAMSUNG M470L3224FT0-CB3
KN.2560B.008
MEMORY DDR333 256MB HYNIX
HYMD232M646D6-J
KN.2560G.001
MEMORY DDR333 512MB INFINEON
HYS64D64020HBDL-6-C (.11u)
KN.51202.025
MEMORY DDR333 512MB
SAMSUNG M470L6524BT0-CB3
KN.5120B.006
MEMORY DDR333 256MB HYNIX
HYMD564M646B6-J
KN.5120G.006
Main Board
Memory
Speaker
Chapter 6
106
TravelMate 4070/4080 FRU List
N/S
SPEAKER SET
23.T50V7.001
10
THERMAL MODULE
60.A51V7.005
NS
NAME PLATE - TM4060
1HYXZZZ24H9
Heatsink
Miscellaneous
NS
RUBBER FOOT
1HYXZZZ24D6
NS
LCD SCREW RUBBER PAD
47.T50V7.003
NS
LCD BEZEL RUBBER PAD
47.T50V7.004
Screw
107
NS
SCREW M2.0X3.0-I-NI-NYLOK
86.A03V7.012
NS
SCREW I2.5*3M-BNIH(M2.5L3)
86.T25V7.012
NS
SCREW M2.5*4L-BZN-NYLOK
86.A03V7.006
NS
SCREW M2.0X5-I-NI-NYLOK
86.T23V7.006
NS
SCREW MM25060IL69
86.A08V7.004
NS
SCREW M2.0*5-I(NI)(NYLOK)
86.T23V7.010
NS
SCREW M2.0X2.5-I-NI-NYLOK
86.A03V7.007
NS
SCREW I2*3M-NIHY (M2L3)
86.T25V7.008
NS
SCREW M1.7*3.0-I (BK)
86.T50V7.001
NS
SCREW I3*3.5M-NIH(M3L3.5)
86.A03V7.011
Chapter 6
Chapter 6
108
Download PDF

advertising