Quantum | 1402 | Owner`s manual | Quantum 1402 Owner`s manual

QUANTUM
SERIES
INNOVATIVE REHAB SOLUTIONS
Including Model: Quantum 1402
1-800-800-8586 (US) 1-888-570-1113 (Canada)
SAFETY
GUIDELINES
WARNING! A Quantum Rehab Specialist or a qualified technician must perform the initial setup
of this power chair and must perform all of the procedures in this manual.
The symbols below are used throughout this owner's manual and on the power chair to identify warnings and important
information. It is very important for you to read them and understand them completely.
WARNING! Indicates a potentially hazardous condition/situation. Failure to follow designated
procedures can cause either personal injury, component damage, or malfunction. On the product,
this icon is represented as a black symbol on a yellow triangle with a black border.
MANDATORY! These actions should be performed as specified. Failure to perform mandatory
actions can cause personal injury and/or equipment damage. On the product, this icon is
represented as a white symbol on a blue dot with a white border.
PROHIBITED! These actions are prohibited. These actions should not be performed at any time or
in any circumstances. Performing a prohibited action can cause personal injury and/or equipment
damage. On the product, this icon is represented as a black symbol with a red circle and red
slash.
Quick Reference Information
Quantum Rehab Specialist:_____________________________________________________________________
Address:________________________________________________________________________________
Phone Number:___________________________________________________________________________
Purchase Date:____________________________________________________________________________
NOTE: This owner’s manual is compiled from the latest specifications and product information available
at the time of publication. We reserve the right to make changes as they become necessary. Any changes to
our products may cause slight variations between the illustrations and explanations in this manual and the
product you have purchased. The latest/current version of this manual is available on our website.
088 609 661
Copyright © 2007
Pride Mobility Products Corp.
INFMANU2669/Rev B/ October 2007
C O N T E N T S
I.
INTRODUCTION ................................................................................................................................ 4
II.
SAFETY ................................................................................................................................................. 5
III. YOUR POWER CHAIR ................................................................................................................... 17
IV. ASSEMBLY ......................................................................................................................................... 21
V.
COMFORT ADJUSTMENTS........................................................................................................ 23
VI. DISASSEMBLY ................................................................................................................................. 29
VII. BATTERIES AND CHARGING ................................................................................................... 30
VIII.CARE AND MAINTENANCE ....................................................................................................... 35
IX. WARRANTY ....................................................................................................................................... 41
APPENDIX I - SPECIFICATIONS ....................................................................................................... 43
Quantum 1402
www.quantumrehab.com
3
I.
INTRODUCTION
SAFETY
WELCOME to Quantum Rehab, a division of Pride Mobility Products Corporation (Pride). The power chair you have
purchased combines state-of-the-art components with safety, comfort, and styling in mind. We are confident that these
design features will provide you with the conveniences you expect during your daily activities. Once you understand
how to safely operate and care for your power chair, it should give you years of trouble free operation and service.
Read and follow all instructions, warnings, and notes in this manual before attempting to operate your power chair
for the first time. You must also read all instructions, warnings, and notes contained in any supplemental instructional booklets for the controller, front riggings, and/or seating system that accompanied your power chair before
initial operation. Your safety depends upon you, as well as your provider, caretaker, or healthcare professional in
using good judgement.
If there is any information in this manual which you do not understand, or if you require additional assistance
for setup or operation, please contact your Quantum Rehab Specialist. Failure to follow the instructions in
this manual and those located on your power chair can lead to personal injury and/or damage to the
power chair, and may void the warranty.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter, or modify this product or remove
or render inoperable or unsafe any guards, shields, or other safety features of this product; fail, refuse, or neglect to
install any retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product.
SHIPPING AND DELIVERY
Before using your power chair, make sure your delivery is complete as some components may be individually
packaged. If you do not receive a complete delivery, please contact your Quantum Rehab Specialist immediately.
Where damage has occurred during transport, either to the packaging or content, please contact the delivery company responsible.
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear about the
safety and reliability of your new power chair, and about the service you received from your Quantum Rehab Specialist.
Please notify us of any change of address, so we can keep you apprised of important information about safety, new
products, and new options that can increase your ability to use and enjoy your power chair. Please feel free to
contact us at the address below:
USA:
Pride Mobility Products Corporation
Attn.: Customer Care Department
182 Susquehanna Avenue
Exeter, PA 18643-2694
customercare@pridemobility.com
1-800-424-8205
Canada:
Pride Mobility Products Company
380 Vansickle Road Unit 350
St. Catharines, Ontario L2R 6P7
1-888-570-1113
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact us and
we will be glad to send you a new one immediately.
4
www.quantumrehab.com
Quantum 1402
II.
SAFETY
PRODUCT SAFETY SYMBOLS
The symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions. It
is very important for you to read and understand them completely.
Read and follow the information in the owner’s manual.
Do not allow unsupervised children to play near the power chair while the batteries are
charging.
Maximum seating weight.
Keep your hands away from the tires when driving. Be aware that loose fitting clothing
can become caught in drive tires.
Use correct tie-down points for controller harness to prevent the harness from getting
caught in the drive tires or pinched in the seat frame, or damaged when passing through
doorways.
Avoid exposure to rain, snow, ice, salt, or standing water whenever possible. Maintain
and store in a clean and dry condition.
Quantum 1402
www.quantumrehab.com
5
II.
SAFETY
Do not lift the mobility vehicle while seated in it.
Do not lift the mobility vehicle while seated in it.
Do not connect an extension cord to the AC/DC converter or the battery charger.
Removal of grounding prong can create electrical hazard. If necessary, properly install
an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access.
Wear safety goggles.
Corrosive chemicals contained in battery.
6
www.quantumrehab.com
Quantum 1402
II.
SAFETY
EMI-RFI - This product has been tested and passed at an immunity level of 20 V/m.
Explosive conditions exist!
Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive
conditions.
Keep tools and other metal objects away from battery terminals.
Battery Set Configuration:
+ = Positive (Red) Terminal Post
– = Negative (Black) Terminal Post
Connect Red wire to Red Positive (+) Terminal Post
Connect Black wire to Black Negative (–) Terminal Post
Do not use batteries with different amp-hour (Ah) capacities. Do not mix old and
new batteries. Always replace both batteries at the same time.
Quantum 1402
www.quantumrehab.com
7
II.
SAFETY
Battery charger for indoor use only.
Disposal and recycling - Contact your Quantum Rehab Specialist for information on proper
disposal and recycling of your Pride product and its packaging.
Locked and in drive mode.
Place unit on level ground and stand to one side when changing from drive mode to
freewheel mode or freewheel mode to drive mode.
Unlocked and in freewheel mode.
Do not place power chair in freewheel mode on a decline.
Do not place power chair in freewheel mode on an incline.
Contains Lead.
8
www.quantumrehab.com
Quantum 1402
II.
SAFETY
GENERAL GUIDELINES
MANDATORY! Do not operate your new power chair for the first time without completely reading
and understanding this owner’s manual.
Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive variety of products to best fit the individual needs of the power chair user. Please be aware that the final selection and
purchasing decision regarding the type of power chair to be used is the responsibility of the power chair user, who is
capable of making such a decision, and his/her healthcare professional (i.e., medical doctor, physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted the power
chair to the user and has assisted the prescribing healthcare professional and/or the Quantum Rehab Specialist in
the instruction process for the use of the product.
There are certain situations, including some medical conditions, where the power chair user will need to practice
operating the power chair in the presence of a trained attendant. A trained attendant can be defined as a family
member or care professional specially trained in assisting a power chair user in various daily living activities.
As you begin using your power chair during daily activities, you will probably encounter situations in which you
will need some practice. Simply take your time and you will soon be in full and confident control as you maneuver
through doorways, on and off of elevators, up and down ramps, and over moderate terrain.
Below are some precautions, tips, and other safety considerations that will help you become accustomed to operating your power chair safely.
Modifications
Pride has designed and engineered your power chair to provide maximum mobility and utility. A wide range of
accessories is available from your Quantum Rehab Specialist to further customize your power chair to better suit
your needs and/or preferences. However, under no circumstances should you modify, add, remove, or disable any
feature, part, or function of your power chair.
WARNING! Do not modify your power chair in any way not authorized by Pride. Do not use
accessories if they have not been tested or approved for Pride products.
Pre-Ride Safety Check
Get to know the feel of your power chair and its capabilities. Pride recommends that you perform a safety check
before each use to make sure your power chair operates smoothly and safely.
Perform the following inspections prior to using your power chair:
! Check for proper tire inflation. Maintain but do not exceed 35 psi (2.4 bar) in each tire if equipped
with pneumatic tires.
! Check all electrical connections. Make sure they are tight and not corroded.
! Check all controller connections to the power base. Make sure they are secured properly.
! Check the brakes. See VIII. “Care and Maintenance.”
! Check battery charge. See VII. “Batteries and Charging.”
NOTE: If you discover a problem, contact your Quantum Rehab Specialist for assistance.
Quantum 1402
www.quantumrehab.com
9
II.
SAFETY
Weight Limitations
Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit.
MANDATORY! Stay within the specified weight capacity of your power chair. Exceeding the weight
capacity voids your warranty. Pride will not be held responsible for injuries and/or property damage
resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your power chair. Carrying passengers on your power
chair may affect the center of gravity, resulting in a tip or a fall.
Tire Inflation
If your power chair is equipped with pneumatic tires, you should check or have the air pressure checked regularly.
Proper inflation pressures will prolong the life of your tires and help ensure the smooth operation of your power chair.
WARNING! It is important that 35 psi (2.4 bar) tire pressure be maintained in pneumatic tires at
all times. Do not underinflate or overinflate your tires. Low pressure may result in loss of control,
and overinflated tires may burst. Failure to maintain 35 psi (2.4 bar) tire pressure in pneumatic
tires at all times may result in tire and/or wheel failure.
WARNING! Inflate your power chair drive tires from a regulated air source with an available
pressure gauge. Inflating your tires from an unregulated air source could overinflate them, resulting
in a burst tire.
Incline Information
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe access. Some ramps
may have turning switchbacks (180-degree turns) that require you to have good cornering skills on your power chair.
! Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
! Take wide swings with your power chair’s front wheels around any tight corners. If you do that, the power chair’s
rear wheels will follow a wide arc, not cut the corner short, and not bump into or get hung up on any railing corners.
! When driving down a ramp, keep the power chair’s speed adjustment set to the slowest speed setting to ensure
a safely controlled descent.
! Avoid sudden stops and starts.
When climbing an incline, try to keep your power chair moving. If you must stop, start up again slowly and then accelerate
cautiously. When driving down an incline, set your power chair to the slowest speed setting and drive in the forward
direction only. If your power chair starts to move down the incline faster than you anticipated or desired, allow it to come to
a complete stop by releasing the joystick, then push the joystick forward slightly to ensure a safely controlled descent.
WARNING! When on any sort of an incline or decline, never place the power chair in
freewheel mode while seated on it or standing next to it.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of
the incline. Drive your power chair straight up the incline. This greatly reduces the
possibility of a tip or a fall. Always exercise extreme caution when negotiating an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e., areas
covered with snow, ice, cut grass, or wet leaves).
WARNING! Never travel down an incline backward. Doing so may cause the power
chair to tip. Always exercise extreme caution when negotiating an incline.
WARNING! If your power chair is equipped with a reclining seatback, do not attempt to
negotiate inclines with the seat in a reclined position. Do not attempt to negotiate
obstacles with the seat in a reclined position unless an attendant is present to help
stabilize the chair. Failure to heed may result in the power chair tipping over.
10
www.quantumrehab.com
Quantum 1402
II.
SAFETY
WARNING! Even though your power chair is capable of climbing slopes greater than those
illustrated in figure 1, do not, under any circumstances, exceed the incline guidelines or any
other specifications presented in this manual. Doing so could cause instability in your power
chair.
In compliance with the Americans with Disabilities Act of 1990, all handicap public access ramps are required to
have a maximum slope of 5° (8.7%). Therefore, Pride recommends that the maximum slope of an incline you
attempt to safely ascend or descend on your power chair does not exceed 5° (8.7%). See figure 1.
WARNING! Any attempt to climb or descend a slope steeper than 5° (8.7%) may put your power
chair in an unstable position and cause it to tip.
5 (8.7%)
Figure 1. Maximum Safe Angle (Ascending and Descending)
Freewheel Mode
Your power chair is equipped with two manual freewheel levers to allow for manual maneuverability by a trained
attendant. For more information about how to place your power chair into and out of freewheel mode, see III. “Your
Power Chair.”
WARNING! Do not use your power chair in freewheel mode without an attendant present.
WARNING! Do not attempt to personally place your power chair in freewheel mode
while seated on it. Ask an attendant for assistance if necessary.
WARNING! Do not place your power chair in freewheel mode while on an incline or
decline. The chair could roll uncontrollably on its own.
Braking Information
Your power chair is equipped with two powerful brake systems:
! Regenerative — uses electricity to rapidly slow the vehicle when the joystick returns to the center/stop position.
! Disc Park Brake — activates mechanically after regenerative braking slows the vehicle to near stop, or when
power is removed from the system for any reason.
Cornering Information
While your power chair is equipped with rear caster wheels and front anti-tip wheels, excessively high cornering
speeds can still create the possibility of tipping. Factors which affect the possibility of tipping include, but are not
limited to: cornering speed, steering angle (how sharply you are turning), uneven road surfaces, inclined road
surfaces, riding from an area of low traction to an area of high traction (such as passing from a grassy area to a
paved area – especially at high speed while turning), and abrupt directional changes. High cornering speeds are
not recommended. If you feel that you may tip over in a corner, reduce your speed and steering angle (i.e., lessen
the sharpness of the turn) to prevent your power chair from tipping.
WARNING! When cornering sharply, reduce your speed and maintain a stable center of gravity.
This greatly reduces the possibility of a tip or fall.
Quantum 1402
www.quantumrehab.com
11
II.
SAFETY
Public Streets and Roadways
WARNING! You should not operate your power chair on public streets and roadways. Be aware
that it may be difficult for traffic to see you when you are seated on your power chair. Obey all
local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with
extreme caution.
Outdoor Driving Surfaces
Your power chair is designed to provide optimum stability under normal driving conditions—dry, level surfaces
composed of concrete, blacktop, or asphalt. However, Pride recognizes that there will be times when you will
encounter other surface types. For this reason, your power chair is designed to perform admirably on packed soil,
grass, and gravel. Feel free to use your power chair safely on lawns and in park areas.
! Reduce your power chair’s speed when driving on uneven terrain and/or soft surfaces.
! Avoid tall grass that can entangle the running gear.
! Avoid loosely packed gravel and sand.
! If you feel unsure about a driving surface, avoid that surface.
Inclement Weather Precautions
Exposure of your power chair to inclement weather conditions should be avoided whenever possible. If suddenly
caught up in rain, snow, severe cold or heat while operating your power chair, proceed to shelter at the earliest
opportunity. Thoroughly dry your power chair before storing, charging, or operating your power chair.
PROHIBITED! Operating in rain, snow, salt, mist/spray conditions, and on icy/slippery surfaces
can have an adverse effect on the electrical system. Maintain and store your power chair in a
dry and clean condition.
WARNING! Prolonged exposure to hot or cold conditions may affect the temperature of upholstered
and non-upholstered items on the power chair, possibly resulting in skin irritation. Exercise caution
when using your power chair in extremely hot or cold conditions or when exposing your power
chair to direct sunlight for prolonged periods of time.
Stationary Obstacles (Steps, Curbs, etc.)
Proceed with extreme caution when driving near raised surfaces, unprotected ledges and/or drop-offs (curbs, porches, stairs,
etc.). Be sure your power chair is traveling perpendicular to any curb you may be required to navigate. See figure 2.
Figure 2. Correct Curb Approach
12
Figure 3. Incorrect Curb Approach
www.quantumrehab.com
Quantum 1402
II.
SAFETY
WARNING! Do not attempt to have your power chair climb or descend an obstacle that is higher
than 2 in. (5 cm) unless you have the assistance of an attendant.
WARNING! Do not attempt to have your power chair proceed backward down any step, curb, or
other obstacle. This may cause the power chair to tip.
Stairs and Escalators
Power chairs are not designed to travel up or down stairs or escalators. Always use an elevator.
WARNING! Never use your power chair to negotiate steps or escalators.
Doors
! Determine if the door opens toward or away from you.
! Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gently and
slowly backward to pull the door open.
Elevators
Modern elevators have a door edge safety mechanism that, when pushed, reopens the elevator door(s).
! If you are in the doorway of an elevator when the door(s) begin to close, push on the rubber door edge or allow
the rubber door edge to contact the power chair and the door will reopen.
! Use care that pocketbooks, packages, or power chair accessories do not become caught in elevator doors.
Lift/Elevation Products
If you will be traveling with your power chair, you may find it necessary to use a lift/elevation product to aid in
transportation. Pride recommends that you closely review the instructions, specifications, and safety information
set forth by the manufacturer of the lift/elevation product before using that product.
WARNING! Never sit on your power chair when it is being used in connection with any
type of lift/elevation product. Your power chair was not designed with such use in mind
and any damage or injury incurred from such use is not the responsibility of Pride.
Motor Vehicle Transport
Pride recommends that you do not remain seated in your power chair while traveling in a motor vehicle. The power chair
should be stowed in the trunk of a car or in the back of a truck or van with batteries removed and properly secured.
WARNING! Do not sit on your power chair while it is in a moving vehicle.
WARNING! Always be sure your power chair and its batteries are properly secured when it is
being transported. Batteries should be secured in a upright position and protective caps should
be installed on the battery terminals. Batteries should not be transported with any flammable or
combustible items.
Positioning Belts
Your Quantum Rehab Specialist, therapist(s), and other healthcare professionals are responsible for determining
your requirement for a positioning belt in order to operate your power chair safely.
WARNING! If you require a positioning belt to safely operate your power chair, make sure it is
fastened securely in order to reduce the possibility of a fall from the power chair.
WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle. Nor is
your power chair suitable for use as a seat in any vehicle. Anyone traveling in a vehicle should be
properly belted into seats approved by the vehicle manufacturer.
Quantum 1402
www.quantumrehab.com
13
II.
SAFETY
Batteries
In addition to following the warnings below, be sure to comply with all other battery handling information. For
more information about your power chair’s batteries, see VII. “Batteries and Charging.”
MANDATORY! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wear goggles and gloves when handling batteries and wash hands after
handling.
WARNING! Power chair batteries are heavy. See specifications table. If you are unable
to lift that much weight, be sure to get help. Use proper lifting techniques and avoid
lifting beyond your capacity.
WARNING! Always protect the batteries from freezing and never charge a frozen battery.
Charging a frozen battery may result in damage to the battery.
WARNING! Connect your battery harnesses in the proper manner. RED (+) cables must
be connected to positive (+) battery terminals/posts. BLACK (-) cables must be
connected to negative (-) battery terminals/posts. Protective caps should be installed
over all battery terminals. REPLACE cables immediately if damaged.
Removable Parts
WARNING! Do not attempt to lift or move a power chair by any of its removable parts, including the
armrests, seat, foot riggings, controller, and shrouds.
Preventing Unintended Movement
WARNING! If you anticipate being seated in a stationary position for an extended period of time,
turn off the power. This will prevent unexpected motion from inadvertent joystick contact. This
will also eliminate the possibility of unintended chair movement from electromagnetic (EM)
sources.
Reaching and Bending
Never reach, lean, or bend while driving your power chair. If it is absolutely necessary to reach, lean, or bend while
seated on your power chair, it is important to maintain a stable center of gravity and keep the power chair from
tipping. Pride recommends that the power chair user determine his/her personal limitations and practice bending
and reaching in the presence of a qualified healthcare professional.
WARNING! Do not bend, lean, or reach for objects if you have to pick them up from the
floor by reaching down between your knees or if you have to reach over the back of
the seat. Movements such as these may change your center of gravity and the weight
distribution of the power chair. This may cause your power chair to tip.
WARNING! Keep your hands away from the tires when driving. Be aware that loose
fitting clothing can become caught in drive tires.
14
www.quantumrehab.com
Quantum 1402
II.
SAFETY
Transfers
Transferring onto and off of your power chair requires a
good sense of balance. Always have an attendant or healthcare professional present while learning to properly transfer yourself.
To eliminate the possibility of injury, Pride recommends that
you or a trained attendant perform the following tasks before attempting a transfer:
! Turn off the power to the controller.
! Ensure your power chair is not in freewheel mode. See
III. “Your Power Chair.”
! Turn the caster wheels toward the transfer destination to
improve power chair stability during transfer.
! Make sure both armrests are flipped up or removed from
your power chair.
! Flip up the foot platform or move the leg rests aside;
this will help to keep your feet from getting caught on
the foot rigging during the transfer.
! Reduce the distance between your power chair and the
object you are transferring onto.
Figure 4. Ideal Transfer Position
WARNING! Before transferring, position yourself as far back as possible in the power chair seat
to prevent the power chair from tipping forward during transfer.
WARNING! Avoid putting all of your weight on the power chair armrests and do not use the
armrests for weight bearing purposes, such as transfers. Such use may cause the power chair to
tip, resulting in a fall from the power chair and personal injury.
WARNING! Avoid putting all of your weight on the foot riggings. Such use may cause the power
chair to tip.
Prescription Drugs/Physical Limitations
Users must exercise care and common sense when operating a power chair. This includes awareness of safety
issues when taking prescribed or over-the-counter drugs or when the user has specific physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter medication or
if you have certain physical limitations. Some medications and limitations may impair your ability
to operate your power chair in a safe manner.
Alcohol/Smoking
The power chair user must exercise care and common sense when operating his/her power chair. This includes
awareness of safety issues while under the influence of alcohol or while smoking.
WARNING! Do not operate your power chair while you are under the influence of alcohol, as this
may impair your ability to operate your power chair in a safe manner.
Quantum 1402
www.quantumrehab.com
15
II.
SAFETY
WARNING! Pride strongly recommends that you do not smoke cigarettes while seated in your
power chair, although the power chair has passed the necessary testing requirements for cigarette
smoking. You must adhere to the following safety guidelines if you decide to smoke cigarettes
while seated in your power chair.
! Do not leave lit cigarettes unattended.
! Keep ashtrays a safe distance from the seat cushions.
! Always make sure cigarettes are completely extinguished before disposal.
Electromagnetic and Radio Frequency Interference (EMI/RFI)
WARNING! Laboratory tests have shown that electromagnetic and radio frequency waves can
have an adverse affect on the performance of electrically-powered mobility vehicles.
Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile twoway radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters, wireless computer links, microwave signals, paging transmitters, and medium-range mobile transceivers used by emergency
vehicles. In some cases, these waves can cause unintended movement or damage to the control system. Every
electrically-powered mobility vehicle has an immunity (or resistance) to EMI. The higher the immunity level, the
greater the protection against EMI. This product has been tested and has passed at an immunity level of 20 V/m.
WARNING! Be aware that cell phones, two-way radios, laptops, and other types of radio
transmitters may cause unintended movement of your electrically-powered mobility vehicle due
to EMI. Exercise caution when using any of these items while operating your mobility vehicle
and avoid coming into close proximity of radio and TV stations.
WARNING! The addition of accessories or components to the electrically-powered mobility vehicle
can increase the susceptibility of the vehicle to EMI. Do not modify your power chair in any way
not authorized by Pride.
WARNING! The electrically-powered mobility vehicle itself can disturb the performance of other
electrical devices located nearby, such as alarm systems.
NOTE: For further information on EMI/RFI, go to the Resource Center on www.pridemobility.com. If
unintended motion or brake release occurs, turn your power chair off as soon as it is safe to do so. Call Pride
at 800-424-8205 to report the incident.
16
www.quantumrehab.com
Quantum 1402
III.
Y O U R
P OWER
CHAIR
THE QUANTUM 1402 POWER CHAIR
Your power chair has two main assemblies: the seat and the power base. Typically, the seating assembly includes
the armrests, seatback, and controller. The power base assembly includes two drive wheels, two anti-tip wheels,
two rear caster wheels, a power seat connector (optional), harness connectors, and a body shroud. See figures 5 and 6.
SEATBACK
ARMRESTS
SEAT ASSEMBLY
CONTROLLER
BODY SHROUD
POWER BASE ASSEMBLY
FOOT RIGGING
(SWING-AWAY
FOOTRESTS
SHOWN)
REAR CASTER WHEEL
ANTI-TIP WHEELS
DRIVE WHEEL
Figure 5. The Quantum 1402 Power Chair
Quantum 1402
www.quantumrehab.com
17
III.
YOUR
POWER
CHAIR
Electronics Tray
The electronics tray is located on the rear of your power chair. The electronics tray is located underneath the rear
sliding door and consists of the ammeter, the charger power cord receptacle, the main circuit breaker, accessory
connector (optional equipment), and the controller connectors(s). See figure 6.
Ammeter: The ammeter displays the charger’s current output in amps. For more information, see VII. “Batteries
and Charging” in this manual.
Charger Power Cord Receptacle: This receptacle is used whenever the batteries need recharging.
Main Circuit Breaker: The main circuit breaker is a safety feature built into your power chair. When the batteries
and the motors are heavily strained (e.g., from excessive loads), the main circuit breaker trips to prevent damage to
the motors and the electronics. If the circuit trips, allow your power chair to “rest” for approximately one minute.
Next, push in the circuit breaker button, turn on the controller, and continue normal operation. If the main circuit
breaker continues to trip repeatedly, contact your authorized Quantum Rehab Specialist.
Accessory Connector (Optional): This is where the optional power harness connects to the controller.
Controller Connector(s): This is where the controller connects to the power base. Each controller uses a different
type of cable. Regardless of which type of controller is used, the cable must be secured to the seat assembly and not
allowed to drag on the floor.
Power Seat Connector (Optional): This is for the optional power seat switch.
AMMETER
MAIN CIRCUIT BREAKER
CHARGER POWER LEAD RECEPTACLE
(SHOWN COVERED)
CONTROLLER CONNECTOR
Figure 6. Electronics Tray
18
www.quantumrehab.com
Quantum 1402
III.
YOUR
POWER
CHAIR
Dual Manual Freewheel Levers
For your convenience, your power chair is equipped with dual manual freewheel levers. The levers are located on the
inside of the anti-tip wheels. The levers allow you to disengage the drive motors and maneuver the chair manually.
WARNING! Do not use the power chair while the drive motors are disengaged! Do not disengage
the drive motors when the power chair is on an incline, as the unit could roll on its own! Only
engage the freewheel mode when on a level surface.
WARNING! It is important to remember that when your power chair is in freewheel mode, the
braking system is disengaged.
To operate the dual manual freewheel levers:
1. Pull both levers upward to disengage the drive motors (freewheel mode). See figure 7.
2. Push both levers downward to engage the drive motors (drive mode). See figure 8.
If a lever is difficult to move in either direction, rock your power chair back and forth slightly. The lever should
then move to the desired position.
WARNING! Do not use the freewheel lever handles as tie-down points to secure this product.
Figure 7. Freewheel Mode (left side shown)
Figure 8. Drive Mode (left side shown)
Active-Trac Suspension
Your power chair is equipped with Active-Trac Suspension (ATS). ATS is a suspension system designed to make
your power chair traverse different types of terrain and obstacles while maintaining smooth operation. With ATS,
the front anti-tip wheels work in conjunction with the motor suspension to help you maneuver over obstacles.
As the front anti-tip wheels come in contact with an obstacle, the front anti-tip wheel assembly is drawn upward.
At the same time, the motors are forced downward. This allows the motors to push the power chair over an
obstacle and limits the possibility of your power chair getting caught on the obstacle.
ATS also helps in day-to-day operating conditions. For instance, when you release the joystick your power chair
begins to slow down. As the chair slows down, the front anti-tip wheels will automatically drop toward the
ground. This will reduce the forward tip that is typically encountered with mid-wheel drive chairs.
Quantum 1402
www.quantumrehab.com
19
III.
YOUR
POWER
CHAIR
Rear Suspension
Your power chair is equipped with rear suspension. See figure 9. This suspension system works in conjunction
with ATS and is designed to maintain a smooth ride when driving over rough terrain and up and down curbs. This
system works by allowing the caster forks to respond to weight transfers and uneven terrain. The rear caster wheels
will pivot as you drive over obstacles. This system also enhances performance when the front anti-tip wheels are set
lower to the surface.
REAR
CASTER
FORK
REAR CASTER WHEELS
REAR
CASTER
FORK
Figure 9. Rear Suspension System
20
www.quantumrehab.com
Quantum 1402
I V.
ASSEMBLY
INITIAL ASSEMBLY
Your power chair may require some assembly either before initial use or after transportation.
NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be
replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon
insert, resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores
or through your Quantum Rehab Specialist.
Seat Installation
Most seats are attached to the power base with the Universal Mounting System (UMS). The UMS consists of
universal parts that may be attached to any medium-back or high-back seat, regardless of seat width or seat depth.
The two main components are aluminum extrusions mounted to the seat base. These extrusions attach to a pair of
trapeze bars that are mounted to the power base. See figure 10.
NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or TRU-Balance Power Positioning System, refer to the information provided in separate manuals.
WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may
lose control of the seat if they do so.
SEAT LATCH SAFETY
REAR EXTRUSION
FRONT EXTRUSION
REAR TRAPEZE BAR
FRONT TRAPEZE BAR
Figure 10. Seat Installation
Quantum 1402
www.quantumrehab.com
21
I V.
ASSEMBLY
To install the seat:
1. Set the trapeze bars to the desired height. To change the trapeze bar height, see V. “Comfort Adjustments.”
2. Tilt the seat back and slide the rear extrusion onto the rear trapeze bar. See figure 10.
3. Lower the front extrusion onto the front trapeze bar until the seat locks into place.
4. Flip the seat latch safety down.
WARNING! Make sure the seat latch safety is flipped down before using your power chair.
5. Install the controller into one of the armrests. See V. “Comfort Adjustments.”
6. Route the controller cable to the rear of the power base.
WARNING! Do not place the controller cable so that it can be pinched in the seat frame or power
base frame.
7. Slide the rear cover open to expose the electronics tray.
8. Plug the controller connector into the electronics tray. See figure 6.
9. Secure the controller cable to the armrest receiver with one or more wire ties.
Power Seat Option Installation
Your power chair may be equipped with the power seat option.
While the seat itself may be any one of the styles offered for this
model, the way the seat base attaches to the Quantum 1402 power
base is different.
To install the power seat:
l. Align the seat post on the seat base to the hole in the actuator.
See figure 11.
2. Insert the seat post into the actuator and push the seat lever
forward.
3. Lock the seat into place.
Figure 11. Power Seat Actuator
22
www.quantumrehab.com
Quantum 1402
V.
COMFORT
ADJUSTMENTS
COMFORT ADJUSTMENTS
After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase
your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and the controller’s position.
NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or Synergy TRU-Balance, refer to
the information provided in separate manuals. If your power chair is equipped with a contoured seating system, refer to the following information.
WARNING! If your power chair was configured at your Quantum Rehab Specialist, please consult
your healthcare professional before changing the seat position or making any other adjustment.
Some adjustments may degrade your power chair’s performance and safety by changing its
center of gravity.
WARNING! Some power chair components are heavy. You may need assistance to lift or carry
them. Please refer to the specifications table for specific component weights before you
disassemble the power chair.
WARNING! Remove the occupant from the power chair before making any adjustments.
You may need the following to make comfort adjustments:
! metric/standard hex key set
! metric/standard socket set and ratchet
! adjustable wrench
Seat Height/Angle Adjustment
The seat is attached to the power base through the UMS.
You can change the seat height by raising the front and
rear trapeze bars. If you raise or lower only one set of
trapeze bars (front or rear), you can also change the seat Figure 12. Seat Latch Safety (Disengaged)
base angle (dump).
QUICK-RELEASE PINS
To change the seat height:
1. Turn off the power to the controller.
2. Unplug the controller connector(s) from the electron- TRAPEZE BARS
ics tray.
3. Flip up the seat latch safety. See figure 12.
SEAT TOWER
4. Squeeze the seat latch and release the seat from the
front trapeze bar.
BALL DETENT PINS
5. Slide the seat forward and remove it from the power
base.
6. Remove the quick-release pins from the seat towers
(front and rear). See figure 13.
7. Remove both trapeze bars from the seat towers.
8. Lift off the shroud
9. Remove the ball detent pin from each of the four seat
towers. See figure 13.
Figure 13. Seat Height Adjustment
Quantum 1402
www.quantumrehab.com
23
V.
COMFORT
ADJUSTMENTS
10. Move the seat towers up or down to the desired height.
11. Reinstall the ball detent pin into each seat tower.
12. Reinstall the shroud.
13. Reinstall the trapeze bars and secure with the quickrelease pins.
14. Reinstall the seat.
WARNING! Make sure the seat latch safety
is flipped down before using the power chair.
15. Plug the controller connector(s) into the electronics tray.
Seat Position
You can move the seat forward or rearward by changing
the extrusion mounting position.
To change the seat position:
1. Turn off the power to the controller.
2. Unplug the controller connector(s) from the electronics tray.
3. Remove the seat from the power base.
4. Remove both extrusions from the bottom of the seat. Figure 14. Seat Position Adjustment
5. Reposition the extrusions on a different set of mounting
holes. You must move both extrusions the same number
of holes either forward or backwards. See figure 14.
6. Fasten the extrusions back onto the bottom of the seat.
JAM NUT
7. Reinstall the seat.
ARMREST ANGLE
8. Plug the controller connector(s) into the electronics tray.
ADJUSTING SCREW
Manual Recline Seatback Adjustment
If your power chair is equipped with a reclining seat, you
can adjust the seatback angle with the seatback release lever. This lever is located on the right side of the seat base.
To adjust the seatback angle:
1. Pull up on the seatback release lever.
2. Lean forward or backwards to the desired position.
3. Release the lever.
Seatback Angle Adjustment
If your power chair is equipped with an adjustable
seatback, you can adjust it to four (4) different angles:
90°, 102°, 105°, or 107°.
ARMREST HEIGHT
ADJUSTING
SETSCREWS
SEATBACK ANGLE
ADJUSTING SCREW
ARMREST
ADJUSTMENT
KNOB
Figure 15. Seatback and Armrest Adjustments
To adjust the seatback angle:
1. Remove the seatback angle adjusting screws from both seat hinges. See figure 15.
2. Set the seatback at the desired angle.
3. Reinstall the screws on both seat hinges and retighten.
24
www.quantumrehab.com
Quantum 1402
V.
COMFORT
ADJUSTMENTS
Armrest Width Adjustment
You can change each armrest’s width independently of the other.
To change the armrest width:
1. Locate the two adjustment knobs on the armrest receiver bracket.
See figure 15.
2. Loosen the knobs.
3. Slide the armrests in or out to the desired width.
4. Tighten the knobs.
Armrest Angle Adjustment
To change the armrest angle:
1. Lift the armrest straight up so that it is perpendicular to the
floor. See figure 15.
2. Loosen the jam nut.
3. Turn the adjusting screw to raise or lower the front of the armrest.
4. Tighten the jam nut to lock the adjusting screw into place.
SETSCREW
Figure 16. Underside of Armrest
Armrest Height Adjustment
To change the armrest height:
1. Loosen the two setscrews located on the armrest receiver. See figure 15.
2. Raise or lower the armrest to the desired height.
3. Tighten the setscrews to secure the armrest.
Controller Position
You can move the controller in toward or out away from the armrest, or change the position of the controller for
either left-hand or right-hand use.
MANDATORY! Prevent controller harness damage! Avoid routing the controller harness on the outside of
the armrest pad. Route the harness under the armrest or toward the inside of the armrest pad. Use
correct tie-down points for the controller harness to prevent the harness from getting caught in the drive
tires, pinched in the seat frame, or damaged when passing through doorways.
To extend the controller:
1. Flip up the armrest so it is perpendicular to the floor.
2. Loosen the setscrew on the controller bracket. See figure 16.
3. Slide the controller into or out of the armrest to the desired position.
4. Tighten the setscrew to secure the controller.
To change the controller position:
1. Unplug the controller connector from the electronics tray. See figure 6.
2. Cut the wire tie that attaches the controller cable to the armrest.
3. Flip up the armrest so that it is perpendicular to the floor.
4. Loosen the setscrew under the armrest. See figure 16.
5. Slide the controller out of the armrest.
6. Loosen the setscrew under the other armrest.
Quantum 1402
www.quantumrehab.com
25
V.
COMFORT
ADJUSTMENTS
7. Place the controller in the other armrest.
8. Tighten the setscrew.
9. Use a wire tie to secure the controller cable to
the armrest.
10. Plug the controller connector into the electronics tray.
NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or a TRU-Balance Power
Positioning System, refer to the information provided in separate manuals.
FOOT PLATFORM
BRACKET NUTS AND
BOLTS
BALL DETENT
PIN
Foot Platform Height Adjustment
The foot platform height is easily adjusted to one
of six different heights in 1-in. (2.54 cm) increments.
To raise or lower the foot platform:
1. Remove the nuts and bolts from the foot platform bracket. See figure 17.
2. Raise or lower the foot platform to the desired
height.
3. Reinstall the bolts and nuts into the foot platform bracket and retighten.
Figure 17. Foot Platform Height/Depth Adjustment
Foot Platform Depth Adjustment
To adjust the foot platform depth:
1. Remove the nuts and bolts from the foot platform
bracket. See figure 17.
2. Move the foot platform in or out to the desired
depth.
3. Reinstall the nuts and bolts into the foot platform bracket and retighten.
Foot Platform Angle Adjustment
You can adjust the angle of the foot platform with
a hex key. See figure 18.
To adjust the foot platform angle:
1. Locate the setscrew on the underside of the foot
platform.
2. Turn the setscrew to raise or lower the front of
the foot platform.
26
SETSCREW
Figure 18. Foot Platform Angle Adjustment
www.quantumrehab.com
Quantum 1402
V.
COMFORT
Power Elevating Seat Option
If your power chair is equipped with a power elevating seat, you can change the seat height automatically. The power elevating seat is operated
through a switch located on one of the armrests or
on the controller.
ADJUSTMENTS
POWER ELEVATING
SEAT SWITCH
To change the seat height using the power elevating seat switch on the armrest:
1. Press forward on the power elevating seat switch
to raise the seat. See figure 19.
2. Pull back on the power elevating seat switch to
lower the seat
WARNING! Do not allow the motor
to run more than a few seconds
after the mechanism reaches the
top or bottom limit.
WARNING! The power elevating
seat option is intended for use on
a level surface only. Never raise the
seat from its lowest position on an
inclined surface. Failure to heed
this war ning can result in the
power chair tipping over.
Figure 19. Power Seat Switch
WARNING! Never raise the seat
from its lowest position when
operating your power chair on
bumpy or uneven surfaces. Failure
to heed this warning can result in
the power chair tipping over.
WARNING! Never raise the power
elevating seat while your power
chair is in freewheel mode.
WARNING! Always fasten the
positioning belt when operating the
power elevating seat.
NOTE: The power elevating seat option is
equipped with a system that reduces the speed of
the power chair by one half when the seat is elevated more than 1–2 inches (2.5-5 cm). Always
check to be sure this system is operating properly
before using your power chair.
Quantum 1402
www.quantumrehab.com
27
V.
COMFORT
ADJUSTMENTS
Figure 21. Anti-Tip Wheel Adjustment (Cam)
Figure 20. Anti-Tip Bracket (Inner Locknut)
Anti-tip Wheel Adjustment
The anti-tip wheels are designed to give your power chair increased stability on rough surfaces. The anti-tip
wheels are preset at the factory for smooth surfaces or indoor use only. If you plan on using your power chair on
rough surfaces, it may be necessary to adjust the anti-tip wheels to better suit your needs. The anti-tip wheels may
need adjustment if either of the following occur:
! When coming to a stop, your power chair tips forward excessively.
! The anti-tip wheels constantly rub the ground.
NOTE: Each drive tire must be inflated to 35 psi (2.4 bar) in order for the anti-tip wheels to be properly
adjusted.
To adjust the anti-tip wheels:
1. Place an adjustable wrench on the inner locknut of the anti-tip bracket located right after the shock strut.
See figure 20.
2. Turn the locknut counterclockwise to loosen.
3. Place your wrench on the adjustable cam located on the other side of the locknut. See figure 21.
4. To adjust the anti-tip upward, turn the cam counterclockwise. To adjust the anti-tip downward, turn the cam
clockwise.
5. Tighten the locknut.
6. Make the same adjustment to the other anti-tip wheel.
WARNING! Consult your Quantum Rehab Specialist before attempting to change the anti-tip
height! Changing the anti-tip wheel height affects handling under deceleration!
WARNING! The higher you raise the anti-tip wheels, the more tendency your power chair has to
tilt forward when coming to a stop. You can compensate for this by making a small adjustment
to the pre-programmed deceleration setting in the controller or by moving the seat assembly
farther to the rear of your power chair.
PROHIBITED! Do not remove the anti-tip wheels.
28
www.quantumrehab.com
Quantum 1402
VI.
DISASSEMBLY
Seat Removal
You may wish to remove the seat for transportation.
NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or TRU-Balance Power
Positioning System, refer to the information provided
in separate manuals.
To remove the seat:
1. Turn off the power to the controller.
2. Make sure your power chair is not in freewheel
mode. See III. “Your Power Chair.”
3. Unplug the controller connector from the electronics tray.
4. Flip up the seat latch safety. See figure 22.
5. Squeeze the seat latch and release the seat from the
front trapeze bar.
6. Slide the seat forward and remove it from the power
base.
Figure 22. Seat Safety Latch
To remove a power seat:
1. Turn off the power to the controller.
2. Disconnect the controller from the electronics tray.
3. Release the seat by moving the seat release lever
backward.
4. Lift up the power seat plate.
5. Lift the seat off of the actuator.
BALL DETENT PIN
Foot Platform Removal
The foot platform helps protect your power chair components from the environment. See figure 23. You must
remove the foot platform in order to change the batteries and check the cable connections.
Figure 23. Foot Frame Removal
To remove the foot platform:
1. Turn off the power to the controller.
2. Make sure your power chair is not in freewheel
mode. See III. “Your Power Chair.”
3. Remove the ball detent pin at the base of the foot
platform bracket.
4. Lift the foot platform straight up approximately
2 in. (5 cm) and pull it away from the power base.
Quantum 1402
www.quantumrehab.com
29
VII.
B ATTERIES AND C HARGING
BATTERIES AND CHARGING
Your power chair uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free. Since
they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a longer
and deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable. Automotive batteries are not designed to handle a long, deep discharge, and also are unsafe for use in powered wheelchairs.
MANDATORY! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wear goggles and gloves when handling batteries and wash hands after
handling.
WARNING! Always use two batteries of the exact same type, chemistry, and amphour (Ah) capacity. Refer to the specifications table in this manual and in the manual
supplied with the battery charger for recommended type and capacities.
WARNING! Contact your Quantum Rehab Specialist if you have any questions regarding
the batteries in your power chair.
Charging The Batteries
The battery charger is essential in providing long life for your power chair batteries. The battery charger is designed to
optimize your power chair’s performance by charging the batteries safely, quickly, and easily. If your power chair is
equipped with an onboard battery charger, the charging system consists of the battery charger, the charger fuse, and the
ammeter. The onboard charger is located underneath the electronics tray. The ammeter and charger fuse are located on
the electronics tray for easy viewing. See figure 6. The ammeter indicates the rate of charge being administered to
fully recharge the batteries. It is also a good indication of whether or not the charger is working. The ammeter and the
charger are only functional when the charger power cord is plugged into an electrical outlet.
PROHIBITED! Removal of grounding prong can create electrical hazard. If necessary, properly
install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access.
PROHIBITED! Never use an extension cord to plug in your battery charger. Plug the charger
directly into a properly wired standard electrical outlet.
PROHIBITED! Do not allow unsupervised children to play near the power chair while the batteries
are charging. Pride recommends that you do not charge the batteries while the power chair is
occupied.
MANDATORY! Read the battery charging instructions in this manual and in the manual supplied
with the battery charger before charging the batteries.
WARNING! Explosive gases may be generated while charging the batteries. Keep the power
chair and battery charger away from sources of ignition such as flames or sparks and provide
adequate ventilation when charging the batteries.
WARNING! You must recharge your power chair’s batteries with the supplied onboard or optional
off-board battery charger. Do not use an automotive-type battery charger.
WARNING! Inspect the battery charger, wiring, and connectors for damage before each use.
Contact your Quantum Rehab Specialist if damage is found.
WARNING! Do not attempt to open the battery charger case. If the battery charger does not
appear to be working correctly, contact your Quantum Rehab Specialist.
WARNING! If the battery charger is equipped with cooling slots, then do not attempt to insert
objects through these slots.
30
www.quantumrehab.com
Quantum 1402
+-
VII.
B ATTERIES AND C HARGING
WARNING! If your battery charger has not been tested and approved for outdoor use,
then do not expose it to adverse or extreme weather conditions. If the battery charger
is exposed to adverse or extreme weather conditions, then it must be allowed to
adjust to the difference in environmental conditions before use indoors. Refer to the
manual supplied with the battery charger for more information.
To charge the batteries using the onboard charger:
1. Position the rear of your power chair next to a standard electrical outlet.
2. Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III.
“Your Power Chair.”
3. Slide the rear cover forward.
4. Extend the charger power cord and plug it into the electrical outlet.
NOTE: The power chair incorporates an inhibit function that disables the power chair when the charger is
plugged into an electrical outlet.
5. We recommend you charge the batteries for 8 to 14 hours. As the batteries charge, the ammeter needle slowly
drops to zero.
NOTE: The ammeter indicates how much charge is needed to fully charge the batteries. Wait about a minute
for the charger to warm up. The ammeter may move as high as 5.5 amps, then gradually move back down to 0
amps as the batteries charge.
6. When the batteries are fully charged, the needle vibrates on or near the zero mark on the ammeter scale.
Unplug the power cord from the electrical outlet, wind it up using the hook and loop strap, and place the cord
back into the electronics tray.
To charge the batteries using the off-board charger:
1. Position the front of your power chair next to a standard electrical outlet.
2. Turn off the power to the controller and engage the manual freewheel lever(s) in the drive position. See III.
“Your Power Chair.”
3. Plug the 3-pin extension cable from the off-board battery charger into the off-board battery charger/programming socket on the controller.
4. Plug the off-board battery charger into the electrical outlet.
NOTE: If it is a Pride off-board charger, then there are two lights in it. The red light indicates that power to the
off-board charger is on. The green light indicates that the batteries are fully charged. If it is not a Pride offboard charger, then follow the instructions supplied by the manufacturer.
.
5. When the batteries are fully charged, disconnect the charger from the electrical outlet, then from the controller.
Quantum 1402
www.quantumrehab.com
31
VII.
B ATTERIES AND C HARGING
Battery Break-In
To break in new batteries for maximum efficiency:
1. Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak
performance level.
2. Operate your power chair about the house and yard. Move slowly at first, and do not travel too far until you
become accustomed to the controls and break in the batteries.
3. Give the batteries another full charge of 8 to 14 hours and operate your power chair again. The batteries should
now perform at over 90% of their potential.
4. After four or five charging cycles, the batteries top off at 100% charge and last for an extended period.
Frequently Asked Questions (FAQs)
How does the charger work?
The battery charger takes the standard electrical outlet voltage of 120 VAC (alternating current) and converts it to
24 VDC (direct current). The power chair batteries use direct current to run your power chair. When the battery
voltage is low, the charger works harder to charge the battery. As the battery voltage approaches full charge, the
charger doesn’t work as hard to complete the charging cycle. When the battery is fully charged, the amperage from
the charger is nearly at zero. This is how the charger maintains a charge but does not overcharge the battery.
Can I use a different battery charger?
You should use the charger supplied with the power chair. It is the safest, most efficient tool to charge the batteries.
We do not recommend using other types of chargers (e.g., an automotive battery charger).
NOTE: Your power chair’s charger will not operate after the batteries have been discharged to nearly zero
voltage. If this happens, call your Quantum Rehab Specialist for assistance.
How often must I charge the batteries?
Many factors come into play when deciding how often to charge the batteries. You may use your power chair all
day on a daily basis or you may not use it for weeks at a time.
! Daily Use
If you use your power chair on a daily basis, charge the batteries as soon as you are finished. Your power chair
will be ready each morning to give you a full day’s service. It is recommended that you charge the batteries 8 to
14 hours after daily use.
! Infrequent Use
If you use your power chair infrequently (once a week or less), you should charge the batteries at least once per
week for 12 to 14 hours.
NOTE: Keep your batteries fully charged and avoid deeply discharging your batteries. Do not charge the batteries for more than 24 hours at a charging cycle.
32
www.quantumrehab.com
Quantum 1402
VII.
B ATTERIES AND C HARGING
How can I get maximum range or distance per charge?
Rarely do you have an ideal driving situation such as smooth, flat, hard terrain with no wind, hills, or curves.
More often you are presented with hills, sidewalk cracks, uneven and loosely packed surfaces, curves, and
wind. All of these factors affect the distance or running time per battery charge. The following are a few suggestions for obtaining the maximum range per charge.
! Always fully charge the batteries prior to your trip.
! Maintain 35 psi (2.4 bar) in pneumatic drive wheels.
! Plan your trip in advance to avoid inclines if possible.
! Limit baggage weight to essential items.
! Try to maintain an even speed and avoid stop-and-go driving.
What type of battery should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. Both AGM and Gel-Cell are deep-cycle
batteries that are similar in performance. Refer to the Specification Table for more information regarding the
batteries used with your power chair.
WARNING! Corrosive chemicals are contained in batteries. Use only AGM or Gel-Cell
batteries to reduce the risk of leakage or explosive conditions.
Why do my new batteries seem weak?
Deep-cycle batteries employ a much different chemical technology than that used in car batteries, nickel-cadmium
batteries (nicads), or in other common battery types. Deep-cycle batteries are specifically designed to provide
power, drain down their charge, and then accept a relatively quick recharge. AGM and Gel-Cell batteries should be
charged as often as possible. They do not have a “memory” like nickel-cadmium batteries.
We work closely with our battery manufacturer to provide a battery that best suits your power chair’s specific
demands. Fresh batteries arrive regularly at Pride and are promptly shipped with a full charge. During shipping, the
batteries encounter temperature extremes that may influence initial performance. Heat robs the charge from the
battery, and cold slows the power available and extends the time needed to recharge the battery (just as with a car
battery).
It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature.
More importantly, it takes a few “charging cycles” (a partial drain—then a full recharge) to establish the critical
chemical balance that is essential to the battery’s peak performance and long life. It is well worth it to take the time
to break in your battery properly.
NOTE: The useful life of a battery is quite often a reflection of the care it receives.
How can I ensure maximum battery life?
A fully charged, deep-cycle battery provides reliable performance and extended battery life. Keep your power
chair’s batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently
charged, or stored without a full charge may be permanently damaged, causing unreliable power chair operation
and limited battery life.
Quantum 1402
www.quantumrehab.com
33
VII.
B ATTERIES AND C HARGING
How should I store my power chair and its batteries?
If you do not use your power chair regularly, we recommend maintaining battery vitality by charging the batteries
at least once a week.
If you do not plan on using your power chair for an extended period, fully charge the batteries prior to storage.
Disconnect the battery harnesses and store the power chair in a warm, dry environment. Avoid temperature extremes, such as freezing and excessively hot conditions, and never attempt to charge a frozen battery. A cold or
frozen battery should be warmed for several days prior to recharging.
NOTE: If you are storing a power chair for an extended period of time, you may wish to block the unit up with
several boards under the frame. This keeps the tires off the ground and prevents the possibility of flat spots
developing in the tires.
What about public transportation?
AGM and Gel-Cell batteries are designed for application in power chairs and other mobility vehicles. These
batteries are Federal Aviation Administration (FAA) approved, allowing safe transportation on aircraft, buses, and
trains, as there is no danger of spillage or leakage. We suggest you contact the carrier’s ticket counter in advance to
determine that carrier’s specific requirements.
What about shipping?
If you wish to use a freight company to ship your power chair to your final destination, repack your power chair in
the original shipping container and ship the batteries in separate boxes.
34
www.quantumrehab.com
Quantum 1402
VIII.
CARE
AND
MAINTENANCE
CARE AND MAINTENANCE
Your Quantum 1402 is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance
checks. You can perform some of these checks, but others require assistance from a Quantum Rehab Specialist.
Preventive maintenance is very important. If you follow the maintenance checks in this section as scheduled, you
can help ensure that your power chair gives you years of trouble-free operation. If you have any doubt as to your
power chair’s care or operation, contact your Quantum Rehab Specialist.
WARNING! Do not service the power chair when the seat is occupied.
Your power chair, like most electrical equipment, is susceptible to damage from the elements. Avoid damp areas of any kind.
WARNING! Direct or prolonged exposure to water or dampness could cause the power
chair to malfunction electronically and mechanically. Water can cause electrical
components to corrode and the chair’s frame to rust. Power chairs should be examined
periodically for signs of corrosion caused by water exposure, bodily fluid exposure,
or incontinence. Damaged components should be replaced or treated immediately.
Should your power chair come in contact with water:
1. Dry your power chair as thoroughly as possible with a towel.
2. Allow your power chair to sit in a warm, dry place for 12 hours to allow unseen water to evaporate.
3. Check the joystick operation and the brakes before using your power chair again.
4. If any inconsistencies are found, take your power chair to a Quantum Rehab Specialist. Power chairs that are
frequently exposed to sources of water, such as incontinence, should be inspected often for corrosion and
electronic components may need to be replaced frequently.
Temperature
! Some of the parts of your power chair are susceptible to extreme changes in temperature. Always keep your
power chair between the temperatures of 18°F (-8°C) and 122°F (50°C).
! In extremely cold temperatures the batteries may freeze. The specific temperature at which they freeze depends on a
number of factors, such as battery charge, usage, and composition of the batteries (e.g., AGM or Gel-Cell).
! Temperatures above 122°F (50°C) may cause your power chair to operate at a reduced speed. This reduced speed is
a safety feature built into the controller that helps prevent damage to the motor and other electrical components.
General Guidelines
! Avoid knocking or bumping the controller, especially the joystick.
! Avoid prolonged exposure of your power chair to extreme conditions, such as heat, cold, or moisture.
! Keep the controller clean.
! Check all connectors on the electronics tray to ensure that they are all tight and secured properly.
! Make sure the drive tires are inflated to 35 psi (2.4 bar).
WARNING! Make sure your tires are inflated to 35 psi (2.4 bar). Do not underinflate or overinflate
your tires. Low pressure may result in loss of control, and overinflated tires may burst. Overinflating
tires can cause them to explode.
WARNING! Do not use a high pressure hose to inflate your tires.
! Use a rubber conditioner on the tire sidewalls to help preserve them.
WARNING! Never use a rubber conditioner on the tread area of the tires; doing so may make the
tires slippery and cause your power chair to skid.
Quantum 1402
www.quantumrehab.com
35
VIII.
CARE
AND
MAINTENANCE
! All wheel bearings are prelubricated and sealed. They require no subsequent lubrication.
! The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help it
retain its high-gloss appearance.
! Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within the battery
well, with the battery terminals facing inward, toward each other. Refer to the frame decal for the correct wiring layout.
WARNING! Even though the power chair has passed the necessary testing requirements
for ingress of liquids, you should keep electrical connections away from sources of
dampness, including direct exposure to water or bodily fluids and incontinence. Check
electrical components frequently for signs of corrosion and replace as necessary.
Daily Checks
! With the controller turned off, check the joystick. Make sure it is not bent or damaged and that it returns to the
center when you release it. Check the rubber boot around the base of the joystick for damage. Visually inspect
the boot. Do not handle or try to repair it. See your Quantum Rehab Specialist if there is a problem.
! Visually inspect the controller harnesses. Make sure that they are not frayed or cut or have any wires exposed.
See your Quantum Rehab Specialist if there is a problem with any of these harnesses.
! Check for flat spots on solid tires. Flat spots could adversely affect stability.
Weekly Checks
! Disconnect and inspect the controller and the charger harnesses from the electronics tray. Look for corrosion.
Contact your Quantum Rehab Specialist if necessary.
! Ensure that all parts of the controller system are securely fastened to your power chair. Do not overtighten any screws.
! Check for proper tire inflation. There should be 35 psi (2.4 bar) in each tire. If a tire does not hold air, see a
Quantum Rehab Specialist for replacement of the tube.
! Check the brakes. This test should be carried out on a level surface with at least three feet (1 meter) of clearance
around your power chair.
To check the brakes:
1. Turn on the controller and turn down the speed level of your power chair.
2. After one second, check the battery condition meter. Make sure that it remains on.
3. Slowly push the joystick forward until you hear the electric brakes click. Immediately release the joystick. You
must be able to hear each electrical brake operating within a few seconds of joystick movement. Repeat this
test three times, pushing the joystick backwards, then left, and then right.
Monthly Checks
! Check that the anti-tip wheels do not rub the ground when you are operate your power chair. Adjust them as
necessary. See V. “Comfort Adjustments.”
! Check for extreme wear on the anti-tip wheels. Replace them as necessary.
! Check for drive tire wear. See a Quantum Rehab Specialist for repair.
! Check the rear casters for wear. Replace them as necessary.
! Check the rear forks for damage or fluttering which indicates that they may need to be adjusted or have the
bearings replaced. See a Quantum Rehab Specialist for repair.
! Keep your power chair clean and free of foreign material, such as mud, dirt, hair, food, drink, etc.
Yearly Checks
Take your power chair to a Quantum Rehab Specialist for yearly maintenance, especially if you use your power chair on
a daily basis. This helps ensure that your power chair is functioning properly and helps prevent future complications.
36
www.quantumrehab.com
Quantum 1402
VIII.
CARE
AND
MAINTENANCE
Storage
Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the
batteries from the power chair. See VII. “Batteries and Charging.”
WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be
damaged.
Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures, or stored
without a full charge may be permanently damaged, causing unreliable performance and limited service life. It is
recommended that you charge the batteries periodically throughout periods of prolonged storage to ensure proper
performance.
You may wish to place several boards under the frame of your power chair to raise it off of the ground during
periods of prolonged storage. This takes the weight off the tires and reduces the possibility of flat spots developing
on the areas of the tires contacting the ground.
Disposal of Your Power Chair
Your power chair must be disposed of according to applicable local and national statutory regulations. Contact
your local waste disposal agency or a Quantum Rehab Specialist for information of proper disposal of power chair
packaging, metal frame components, plastic components, electronics, and batteries.
Cleaning Instructions
! Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your power chair.
Avoid using products that may scratch the surface of your power chair.
! If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use on
your product before application.
WARNING! Follow all safety instructions for the proper use of the disinfectant and/or cleaning
agent before applying it to your product. Failure to comply may result in skin irritation or premature
deterioration of upholstery and/or power chair finishes.
WARNING! Never hose off your power chair or place it in direct contact with water. Your
power chair has a painted, ABS plastic body shroud that allows it to be easily wiped clean
with a damp cloth.
WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become
slippery or dry out and crack. Use soapy water and dry the seat thoroughly.
Wheel Replacement
If you have pneumatic tires and you have a flat tire, replace the tube. If your chair is equipped with a solid tire
insert, then replace the entire wheel assembly. Replacement tires, tubes, and wheel assemblies are readily available
through your Quantum Rehab Specialist.
WARNING! The wheels on your power chair should only be serviced or replaced by a Quantum
Rehab Specialist or a qualified technician.
WARNING! Be sure that the power to the controller is turned off and the power chair is not in
freewheel mode before performing this procedure.
WARNING! When changing a tire, remove only the center lug nut and washer, then remove the
wheel. If any further disassembly is required, deflate the tire completely or it may explode.
Quantum 1402
www.quantumrehab.com
37
VIII.
CARE
AND
MAINTENANCE
TIRE
TUBE
FRONT RIM HALF
DRIVE WHEEL NUT
SCREWS
REAR RIM HALF
DRIVE WHEEL WASHER
Figure 24. Quantum 1402 Drive Wheel
Figure 25. Quantum 1402 Drive Wheel Disassembled
Follow these easy steps for a quick and safe repair for both solid and pneumatic tires:
1. Turn off the power to the controller.
2. Set the power chair up on blocks.
3. If you are changing a pneumatic tire, completely deflate it before removing the wheel.
4. Remove the drive wheel nut and washer from the axle. See figure 24.
5. Pull the wheel off the axle.
6. Remove the screws from the rim assembly and separate the front and rear rim. See figure 25.
7. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly
if it is a solid tire.
8. Reassemble the rims and reinstall the screws.
9. Slide the wheel back onto the axle.
10. Reinstall the drive wheel nut and washer Onto the axle and tighten.
11. Inflate the pneumatic tires to 35 psi (2.4 bar).
12. Remove the power chair from the blocks.
Battery Replacement
A diagram is printed on a decal on your power chair frame near the battery tray. See
figure 26.
MANDATORY! Batter y posts, terminals, and related
accessories contain lead and lead compounds. Wear
goggles and gloves when handling batteries and wash
hands after handling.
WARNING! The batteries in your power chair should only
be serviced or replaced by a Quantum Rehab Specialist
or a qualified technician.
WARNING! Do not replace the batteries when the seat is
occupied.
WARNING! Do not mix or match new and old batteries. If
you encounter a situation where one battery needs to
be replaced, then replace both batteries. Refer to
specifications table in this manual and the manual
supplied with the battery charger for recommended type
and capacities.
38
www.quantumrehab.com
Figure 26. Battery Connections
Quantum 1402
VIII.
CARE
AND
MAINTENANCE
Battery Replacement
A diagram is printed on a decal on the power chair frame near the battery tray.
To replace the battery:
1. Turn off the power to the controller.
2. Remove the detent pin from the bottom of the foot frame. See figure 17.
3. Lift the foot frame straight up to remove it from the mounting bracket.
4. Locate the two wiring harnesses that are attached to the batteries.
5. Disconnect the two harnesses from their respective quick disconnects by pulling the quick disconnects toward
you.
6. Remove the batteries from the power base assembly.
7. Disconnect the battery harnesses from the positive and negative terminals.
8. Replace the old batteries with new ones.
9. Connect the wire labeled BAT (+) to the positive (red) terminal of one battery.
10. Connect the wire labeled BAT (-) to the negative (black) terminal of the same battery.
11. Install the battery into the rear of the battery tray with the battery terminals facing inward, toward the center of
the power chair. Plug the wiring harness into a quick disconnect.
12. Connect the wire labeled BAT (+) to the positive (red) terminal of the other battery.
13. Connect the wire labeled BAT (-) to the negative (black) terminal of the same battery.
14. Install the battery into the front of the battery tray with the battery’s terminals facing inward, toward the center
of the power chair. Plug the wiring harness into a quick disconnect.
WARNING! Make sure you tighten the fasteners so that the connections are secure.
15. Replace the foot frame using the detent pin to secure.
When to See Your Quantum Rehab Specialist for Service
The following symptoms could indicate a serious problem with your power chair. If necessary, contact your
Quantum Rehab Specialist. When calling, have the model number, serial number, nature of the problem, and
the trouble code if available.
! Motor noise
! Frayed harnesses
! Cracked or broken connectors
! Uneven wear on any of the tires
! Jerky motion
! Pulling to one side
! Bent or broken wheel assemblies
! Does not power up
! Powers up, but does not move
Quantum 1402
www.quantumrehab.com
39
VIII.
CARE
AND
MAINTENANCE
Corrective Maintenance
If the battery condition meter does not light up when you turn on the power:
! Check the harness connections. Make sure they are tight.
! Check the circuit breaker. Reset it if necessary.
! Check the battery connections.
If the above conditions prove normal, you can load test the batteries with a battery load tester. These testers are
available at automotive parts stores. Disconnect both batteries before load testing and follow the directions that
come with the load tester. If either one of the batteries fails the load test, replace both of them. If your power chair
still does not power up, contact your Quantum Rehab Specialist.
40
www.quantumrehab.com
Quantum 1402
IX.
WARRANTY
LIFETIME LIMITED WARRANTY
For the lifetime of your power chair from the date of purchase, Pride will repair or replace at our option to the
original purchaser, free of charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in material and/or workmanship:
Structural frame components, including:
! Main Frame
! Fixed-position seat post
TWO-YEAR LIMITED WARRANTY
For two (2) years from the date of purchase, Pride will repair or replace at our option to the original purchaser, free
of charge, any of the following parts found upon examination by an authorized representative of Pride to be
defective in material and/or workmanship:
Electronic components, including:
! Charger Assembly
! Controller
! Joystick
Other components, including:
! Foot riggings
Main frame assemblies, including:
! Anti-tip forks
! Caster forks
! Caster beam
! Metal seat framing
! Electrical Harnesses
! Foot rigging mounting brackets
18-MONTH LIMITED WARRANTY
For eighteen (18) months from the date of purchase, Pride will repair or replace at our option to the original
purchaser, free of charge, any of the following parts found upon examination by an authorized representative of
Pride to be defective in material and/or workmanship:
! Motor/gearbox assembly
! Power seat actuator
ONE-YEAR LIMITED WARRANTY
For one (1) year from the date of purchase, Pride will repair or replace at our option to the original purchaser, free
of charge, any of the following parts found upon examination by an authorized representative of Pride to be
defective in material and/or workmanship:
! Accessories
! Brakes (electronic function ONLY)
SIX-MONTH LIMITED WARRANTY
For six (6) months from the date of purchase, Pride will repair or replace at our option to the original purchaser,
free of charge, any of the following parts found upon examination by an authorized representative of Pride to be
defective in material and/or workmanship:
! Bearings and bushings
! Plastic components, except body
The battery is covered by a separate six-month warranty, provided by the battery manufacturer. The batteries are
not warranted by Pride.
Quantum 1402
www.quantumrehab.com
41
IX.
WARRANTY
RECONDITIONED UNITS WARRANTY
All reconditioned units are covered by a six-month warranty from Pride effective from the date of purchase.
WARRANTY EXCLUSIONS
This warranty does not extend to those items which may require replacement due to normal wear and tear.
! ABS Plastic shrouds
! Motor brushes
! Upholstery and seating
! Brake Pads
! Tires and tubes
! Fuses/Bulbs
! Circumstances beyond the control of Pride
! Labor, service calls, shipping, and other charges incurred for repair of the product, unless specifically autho-
rized, IN ADVANCE, by Pride Mobility Products Corporation
! Repairs and/or modifications made to any part without specific consent from Pride
Exclusions also include components with damage caused by:
! Contamination
! Abuse, misuse, accident, or negligence
! Battery fluid spillage or leakage
! Commercial use, or use other than normal
! Improper operation, maintenance, or storage
NOTE: Gradual deterioration in performance because the battery has been left in a discharged state, left in
cold conditions for an extended period of time, or worn out through heavy use is not covered.
SERVICE CHECKS AND WARRANTY SERVICE
Warranty service must be performed by a Quantum Rehab Specialist. Do not return faulty parts to Pride without
prior written authorization. All transportation costs and shipping damage incurred while submitting parts for repair
or replacement are the responsibility of the purchaser.
Failure to follow the instructions, warnings, and notes in the owner’s manual and those located on your Pride
product can result in personal injury or product damage and will void Pride’s product warranty.
There is no other express warranty.
IMPLIED WARRANTIES
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1)
year from the date of purchase and to the extent permitted by law. Any and all implied warranties are excluded.
This is the exclusive remedy. Liabilities for consequential damages under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion of
limitation incidental or consequential damages. The above limitation or exclusion may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from state to state.
Please fill out and return the product registration card to Pride. This will aid Pride in providing the best possible
technical and customer service.
42
www.quantumrehab.com
Quantum 1402
APPENDIX
I
-
SPECIFICATIONS
SPECIFICATIONS
Suspension:
Drive Wheels:
Caster Wheels:
Anti-tip Wheels:
Maximum Speed:¹
Range:¹
Brakes:
Ground Clearance:²
Turning Radius:²
Overall Size:²
Drivetrain:
Batteries:³
Battery Charger:
Weight Capacity:
Component Weights:
1
²
³
Active-Trac system and rear suspension
14 in. (35.5 cm), pneumatic or solid, center-mounted
8 in. (20.32 cm), solid, rear articulating
6 in. (15.24 cm), solid, front-mounted
Up to 4.5 mph (7.25 km/h) with high-torque motors (standard)
Up to 6 mph (9.65 km/h) with high-speed motors (optional)
Variable up to 25 miles (40 km)
“Intelligent Braking,” electronic, regenerative disc brakes
See figure 27.
See figure 27.
Length: See figure 27.
Width: See figure 27.
Two-motor, mid-wheel
Two 12-volt deep-cycle, Group 24 batteries
NF-22 batteries for the power seat option
8-amp, off-board (standard)
5-amp, onboard (optional)
5-amp, onboard/8-amp, off-board combo (optional)
400 lbs. (181 kg) with high-torque motors
325 lbs. (147 kg) with high-speed motors
Base: 129 lbs. (58.5 kg)
Batteries: 53.5 lbs. (24 kg) each
Varies with base model, user weight, terrain type, battery amp hour rating (Ah), battery charge, battery condition,
motors, controller type, tire type, and tire condition.
Due to manufacturing tolerances and continued product improvement, this specification can be subject to a variance of
(+ or – ) 3%.
AGM or Gel-Cell type required. See VII. “Batteries and Charging.”
NOTE: All specifications subject to change without notice.
Quantum 1402
www.quantumrehab.com
43
APPENDIX
I
-
SPECIFICATIONS
LENGTH
46.25 in. (117.48 cm)
41 in. (104.14 cm)
TURNING RADIUS
1 in. (2.54 cm)
23 in.
(58.42 cm)
WIDTH
25.75 in. (65.41 cm)
1 in.
(2.54 cm)
1.75 in.
(4.45 cm)
GROUND CLEARANCE
Figure 27. Quantum 1402 Dimensions and Ground Clearance
44
www.quantumrehab.com
Quantum 1402
NOTES
Quantum 1402
www.quantumrehab.com
45
NOTES
46
www.quantumrehab.com
Quantum 1402
Quality Control - Quantum 1402
Inclusion of all Parts
Joystick Serial Number
Controller Serial Number
Left Motor Serial Number
Right Motor Serial Number
Fit and Finish
Performance
Pride keeps a more detailed report on file at the factory.
Date Inspected
Inspector
*INFMANU2669*
Product Serial #
Download PDF