Acnodes PMH8170 Open Frame - High Brightness LCD Display User manual
Add to my manualsadvertisement
User Manual
MCS: Multi-display control solution
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
MCS
Multi-display Control Module Panel
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< Part. 1 > Interface
1.1 Connection
1.2 Connection Standard
< Part. 2 > Command
2.1 CAN Bus Registry
2.2
2.3
Get Address
Get Name
2.4
2.5
2.6
2.7
Get Power Status
Get Display Status
Get Screen Status
Get PIP Status
2.8
2.9
Get Display ID
Get Display Name
2.10 Get Display ID & Name
2.11 Volume Control
2.12 Mute Control
2.13 Input Source Select
2.14 OSD Button Control
2.15 Infrared Remote Control
2.16 Sound Select Control
2.17 Contrast Control
2.18 Brightness Control
2.19 Auto Adjust Control
2.20 Power Control
2.21 PIP Control
2.22 PIP Source Control
2.23 PIP Swap Control
2.24 PIP Location Control
Contents
P.1
P.2 - 3
P.4
P.5
P.6
P.7
P.8
P.9
P.10
P.11
P.12
P.13
P.14
P.15
P.16
P.17
P.18
P.19
P.20
P.21
P.22
P.23
P.24
P.25
P.26 - 27
P.28
P.29
< Part 1 > Interface
< 1.1 > Connection play ’s LINK port and then begin to add connections from a LCD display, starting from the OUT port.
- The first & last LCD displays located at both ends of dais y chain connection must be term inated by setting the pin 1 & 2 of DIP switch ( Set ) to ON position, located next to OUT port. For other daisy chain LCD display(s), please keep the pin 1 & 2 of DIP switc h at OFF position ( Pin 1 & 2 are default at OFF position ).
*The new DIP switch setting requires a power cycle of LCD display to take effect.
- The MCS m odule of LCD display will automatically assign an available ID number from 1 to 64 to each LCD display when connected to the daisy chain, to elim inate LCD displays tr ying to use the same IDs simultaneously.
Fig. 1- 1 Connecting the PC & LCD Displays
RS-232C
15 feet serial cable
( over 15 feet, extender re quired )
Set switc h
For th e 1st and last display, push the set switch upward
For other daisy chain displays, push the set switch downward
RJ-45 jack
LINK OUT IN
Cat5 / 6 cable max. 300 meters
OUT IN
Cat5 / 6 c able max. 300 meters
Daisy chain up to 1,000 meter s and 64 displays
OUT IN
Cat5 / 6 cable max. 300 meters
OUT up to 64 displays
< 1.2 > Connection Standard
1) Computer to LCD display connection standard
- Conducts bi-directional communication using serial RS232.
- Use three signal wires of TxD, ( pin 2 ), RxD ( pin 3 ) and GND ( pin 5 ), among the RS232 standard wires, as Fig. 2-1.
- Use DTR ( pin 4 ), RTS ( pin 7 ) for hot-plug detect.
- The distance between the PC computer to LCD display is limited 15m.
2) LCD display to LCD display connection standard
- Conducts bi-directional communication using CAN bus
- A maxim um of 64 LCD display units can be dais y chained to one CAN bus, up to 1,000 meters.
- The distance between LCD Displays is limited 300 meters via Cat 5/ 6 cable.
3) Command communications
The CAN bus requires the MCS module of LCD display registration by sending command < 0x01 > to add or remove the LCD display(s) from the CAN bus before com mand com munications. Please refer to page 6 for m ore details.
All communications are conducted in the form of hexadec imal number, and the checksum c alculation method as below :
Total = Command + ID + Val1 + Val2 + Val3 + Val4 + Val5 + Val6;
Checksum = 256 – Total;
* Unsigned character of Chec ksum, Total=0;
Get Power Status ( e.g. Power ON & ID=1 )
Header
0x4D,
0x43,0x06
Command
0 x04
ID
Val 1
Power
Val 2
0x00
Val 3
0x00
Val 4
0x00
Val 5
0x00
Val 6
0x00
Header Command
Checksum
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
0x4D,
0x43,0x06
0 x04
0x01
0x01 0x00 0x00 0 x00 0x00 0x00
0xFA
Footer
0x0D, 0x0A
Footer
0x0D, 0x0A
Here, each set functions according to the com mands received and responds with ACK at the same time.
Therefore, the operation of each set s hould be checked after this process.
MCS
Multi-display Control Module Panel
< 1.2 > Connection Standard
4) The status lights ( LED )
Port
IN
IN
Color Activity
Green
Solid LED indicates that the MSC board is powe red on.
No light indica tes the board is powered off.
Orange
Blinkin g L ED indicated that the data is being transmitte d th rough the connection. No lig ht indicates no data is transmitted
Table 2-1 RS-232 Communication Standards
Bit Rate
Data Bits
Parity
Stop Bits
Flow Control
9600 bps
8 bits
None
1 bit
None
Fig. 2-1 RS-232 pin out DB-9 pin used for Asynchronous Data
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< Part 2 > Command
No.
1
Type of Command
CAN Bu s Registry
2 Get Address
3 Get Name
4 Get Power Status
5 Get Display Status
6 Get Screen Sta tus
7
8
9
Get PIP Sta tus
Set Display ID
Set Display Name
10 Show Display ID & Name
11 Volume Control
12 Mute Control
13 I nput Source Select
14 OSD Button Control
15 I nfrared Remote Control
16 Sound Select Control
17 Contrast Control
18 Brightness Con trol
19 Auto Adjust
20 Power Control
21 PIP Control
22 PIP Source Select
23 Main-PIP Swap Co ntrol
24 PIP Locate Control
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
MCS
Multi-display Control Module Panel
0x28
0x45
0x50
0x51
0x52
0x53
0x21
0x22
0x23
0x24
0x25
0x26
0x27
Command Range of Value ( Decimal ) Wait ACK (ms)
0x01 -2,000
0x02 -200
0x03
0x04
--
0 ~ 1
200
200
0x05
0x06
0x07
0x15
0x16
0x17
0x20
--
--
--
1 ~ 64
--
5 ~ 255
0 ~ 100
200
200
200
200
200
200
200
0
0 ~ 1
--
--
0
--
0 ~ 100
--
0 ~ 1
0 ~ 1
--
0 ~ 100
0 ~ 100
5,000
7,000
200
200
200
200
200
2,000
200
200
200
200
200
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.1 > Detailed Description of Commands
1) CAN Bus Registry
• Function
The computer registers the MCS module of LCD display(s) to CAN bus daisy chain c onnection.
*Registration requires when add or rem ove the LCD displays from the CAN bus connection.
• Register MCS Module(s)
Header Command ID Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
Checksum
Footer
0x06, 0x4D,0x43 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x0D, 0x0A
• Ack
He ader
0x4D, 0x43 ,0x06
Command
0x01
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
MAC1 MAC2 MAC3 MAC4 0x00 0x00
Checksum
Footer
0x0D, 0x0A
MAC1 : The 1st byte of MAC address for the LCD display
MAC2 : The 2nd byte of MAC address for the LCD display
MAC3 : The 3rd byte of MAC address for the LCD display
MAC4 : The 4th byte of MAC address for the LCD display
• Nak
He ader
0x4D, 0x43 ,0x15
Co mmand
0x01
ID
Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
ERR 0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
ERR : Error code that shows the type of error that occurred
0x10 Display contro ller error
0x11 Serial controller error
0x12 Unsupported Command
0x13 Checksum error
0x14 Bad param ete r
0x15 Unknown error
MCS
Multi-display Control Module Panel
< 2.2 > Get Address
• Function
The com puter shows the 32-bit MAC addres s of the LCD display
• Get LCD Display Address
Header
0x06, 0x4D,0x43
Command
0x02
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
0x00 0x00 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
• Ack
Header
0x4D, 0x43,0x06
Comm and
0x02
ID
Val 1 Va l 2 Val 3 Val 4 Val 5 Val 6
MAC1 MAC2 MAC3 MAC4 0x00 0x00
Checksum
Footer
0x0D, 0x0A
• Nak
Header
0x4D, 0x43,0x15
Command
0x02
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
ERR 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
MCS
Multi-display Control Module Panel
Multi-display Control Module Panel
< 2.3 > Get Name
• Function
The computer shows the name of the LCD display
• Get LCD Display Address
Header Command Val 1 Val 2 Val 3 Val 4 Val 5 Val 6 Footer
ID Checksum
0x06, 0 x4D,0x43 0x03 0x00 0x00 0x00 0x00 0x00 0x00 0x0D, 0 x0A
• Ack
Header
0x4D, 0x4 3,0x06
Command
0x0 3
ID
Val 1
Char1
Val 2
Char 2
Val 3
Char3
Val 4
Char4
Val 5
Char5
Val 6
Char6
Checksum
Footer
0x0D, 0x0A
Char1 : The 1st character of the name
Char2 : The 2nd character of the name
Char3 : The 3rd character of the name
Char4 : The 4th character of the name
Char5 : The 5th character of the name
Char6 : The 6th character of the name
• Nak
*The default value of the character of the nam e is 0xFF
He ader
0x4D, 0x43 ,0x15
Co mmand
0x03
ID
Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
ERR 0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.4 > Get Power Status
• Function
MCS
Multi-display Control Module Panel
The computer shows the power status of the screen of LCD display
• Get Power Status
Header Command
0x06, 0x4D,0x43 0x04
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
0x00 0x00 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
• Ack
Header
0x4D, 0x43,0x06
Command
0x04
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
P ower 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
Power : The power code for the LCD display
0x00 Power OFF
0x01 Power ON
• Nak
Header
0x4D, 0x43,0x15
Command
0x04
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
ERR 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.5 > Get Display Status
• Function
The computer shows the current s etting of the LCD display
MCS
Multi-display Control Module Panel
• Get LCD Display Address
Header
0x06, 0 x4D,0x43
Command
0x05
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
0x00 0x00 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0 x0A
• Ack
Header
0x4D, 0x4 3,0x06
Command
0x0 5
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
Vol Mute Input OSDB IR Sound
Check- sum
Footer
0x0D, 0x0A
Vol : The volume value of the LCD display ( 1~100 )
Mute : The mute code for the LCD display
Input : The input source code for the LCD display
OSDB : The OSD button control code for the LCD display
IR : The infrared remote control code for the LCD display
Sound : The sound select code for the LCD display
• Nak
He ader Co mmand Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
ID
0x4D, 0x43 ,0x15 0x05 ERR 0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.6 > Get Screen Status
• Function
MCS
Multi-display Control Module Panel
The computer shows the current screen setting of the LCD display
• Get Sc reen Status
Header
0x06, 0x4D,0x43
Command
0x0 6
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
0x00 0x00 0x00 0x00 0x00 0x00
Che cksum
Footer
0x0D, 0x0A
• Ack
Header
0x4 D, 0 x43,0x06
Command
0x06
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
Ctrast Br ight 0x00 0x00 0x00 0x00
Checksum
Foo ter
0x0D, 0x0A
Ctrast : The contrast value of the display
Bright : The brightness value of the display
• Nak
Header Command Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
ID
0x4D, 0x43,0x15 0x0 6 ERR 0x00 0x00 0 x00 0x00 0x00
Checksum
Footer
0x0D, 0 x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.7 > Get PIP Status
• Function
The computer shows the PIP setting of the LCD display
MCS
Multi-display Control Module Panel
The PIP function may or not be av ailable on a particular LCD display depending on the model selected
• Get PIP Status
Header
0x06, 0 x4D,0x43
Command
0x07
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
0x00 0x00 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0 x0A
• Ack
Header
0x4D, 0x4 3,0x06
Command
0x07
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
PIP P.Sour
P. Loc 0x00 0x00 0x00
Che cksum
Footer
0 x0D, 0x0A
PIP : The PIP status value code for the display
P.Sour : The PIP source code for the display
P.Loc : The PIP location code for the display
• Nak
He ader
0x4D, 0x43 ,0x15
Co mmand
0x07
ID
Val 1
ERR
Val 2
0x0 0
Va l 3
0x00
Val 4
0x00
Val 5
0x00
Val 6
0x00
Checksum
Footer
0x0D, 0x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
MCS
Multi-display Control Module Panel
< 2.8 > Set Display ID
• Function
The computer changes the LCD display ID num ber.
• Set Dis play ID number
Header Command
0x06, 0x4D,0x43 0x1 5
ID
Val 1 Val 2 Val 3 Val 4 Va l 5 Val 6
NewID 0x00 0 x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
NewID : Changes the LCD dis play ’s ID to New ID number (1~64).
*The new ID number will be treated as bad parameter, if the num ber is 0, 65 ~ 255 or the new ID number already occupied by other LCD display.
• Ack
Header
0x4 D, 0 x43,0x06
Command
0x15
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
NewID 0x00 0 x00 0x00 0x00 0x00
Checksum
Foo ter
0x0D, 0x0A
• Nak
Header
0x4D, 0x43,0x15
Command
0x1 5
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
ERR 0x00 0x00 0 x00 0x00 0x00
Checksum
Footer
0x0D, 0 x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.9 > Set Display Name
• Function
The computer sets the name of the LCD display.
• Set Display Name
Head er
0x06, 0x4D,0x43
Command
0x16
ID
MCS
Multi-display Control Module Panel
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
Char1 Char2 Char3 Char 4 Char 5 Char6
Checksum
Footer
0x0D, 0x0 A
Char1 : The 1st character of the name
Char2 : The 2nd character of the name
Char3 : The 3rd character of the name
Char4 : The 4th character of the name
Char5 : The 5th character of the name
Char6 : The 6th character of the name
*Character of the nam e c an allow [ a~z ],[ A~Z] , [ 0-9 ] & space character.
• Ack
Header
0x4D, 0x43,0x06
Command
0x16
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
Char 1 Char2 Char3 Char4 Char5 Char 6
Che cksum
Footer
0x0D, 0 x0A
• Nak
Heade r
0x4D, 0x43,0x15
Command
0x16
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
ERR 0x00 0x00 0x00 0x00 0x00
Checksum
Foo ter
0x0D, 0x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.10 > Show Display ID & Name
• Function
MCS
Multi-display Control Module Panel
The LCD Display shows the ID number & name on the screen
• Show Display ID and Name
Header Command Val 1 Val 2 Val 3 Val 4 Val 5 Va l 6 Footer
ID Checksum
0x06, 0x4D,0x43 0x17 Time 0x 00 0x00 0x00 0x00 0x00 0x0D, 0x0A
Tim e : The second value for the s creen shows the display ID no. & name ( 5~255 )
• Ack
Header
0x4D, 0x43,0x06
Command
0x17
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
Time 0x00 0x00 0x00 0x00 0x00
Checksum
Foo ter
0x0D, 0x0A
• Nak
Header
0x4D, 0x43,0x15
Command
0x17
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
ERR 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.11 > Volume Control
• Function
The computer changes the volume level of the LCD display
MCS
Multi-display Control Module Panel
The audio function may or not be available on a partic ular LCD display depending on the model selected
• Set Volum e
Head er
0x06, 0x4D,0x43
Command
0x20
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
Vol 0x00 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0 A
Vol : The volume level value code of the LCD display (0~100)
• Ack
Header Command Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
0x4D, 0x43,0x06 0x20
ID
Vol 0x0 0 0x00 0x00 0x00 0 x00
Che cksum
Footer
0x0D, 0 x0A
• Nak
Heade r
0x4D, 0x43,0x15
Command
0x20
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
ERR 0x00 0x00 0x00 0x00 0x00
Checksum
Foo ter
0x0D, 0x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.12 > Mute Control
• Function
MCS
Multi-display Control Module Panel
The computer turns the mute ON or OFF of the LCD display
The audio function may or not be available on a particular LCD display depending on the model selected
• Set Mute Control
Header
0x06, 0x4D,0x43
Command
0x21
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
Mute 0x00 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
Mute : The mute code for the LCD display
0x00 Mute OFF
0x01 Mute ON
• Ack
Header
0x4D, 0x43,0x06
Command
0x21
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
Mute 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
• Nak
Header
0x4D, 0x43,0x15
Command
0x21
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
ERR 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.13 > Input Source Select
• Function
The computer changes the input source of the LCD display
Some of inputs may or not be available on a particular LCD display depending on the model selected
• Set Input Source
Header
0x06, 0x4D,0x43
Command
0x22
ID
Val 1
Input
Val 2
0x00
Val 3
0x00
Val 4
0x00
Val 5
0x00
Val 6
0x00
Checksum
Footer
0x0D, 0x0A
Input : The input source code for the LCD display
0x10 V GA
0x11 S-Vide o
0x12 Composite
0x13 DVI-D
0x14 HDMI
0x15 S DI
0x16 YPbPr
0x17 TV
• Ack
Header
0x4D, 0x43,0x06
Command
0x22
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
Input 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
• Nak
Header
0x4D, 0x43,0x15
Command
0x22
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
ERR 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
< 2.14 > OSD Button Control
• Function
The computer switches the OSD button function ON /OFF
MCS
Multi-display Control Module Panel
• Set OSD Button
Header
0x06, 0x4D,0x43
Command
0x23
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
OSDB 0x00 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
OSDB : The OSD mem brane button control code for the LCD display
0x00 OFF
0x01 ON
• Ack
Header
0x4D, 0x43,0x06
Command
0x23
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
OSDB 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
• Nak
Header
0x4D, 0x43,0x15
Command
0x23
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
ERR 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
MCS
Multi-display Control Module Panel
< 2.15 > Infrared Remote Control
• Function
The com puter enables and disables the infrared reception feature of the LCD display
• Set Infrared Remote
Header Command
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
0x06, 0 x4D,0x43 0x24 IR 0x00 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0 x0A
IR : Reception enable / disable code for the LCD display infrared remote control
0x00 Remote Disable
0x01 Remote Enable
• Ack
Header
0x4D, 0x4 3,0x06
Comm and
0x24
ID
Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
IR 0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
• Nak
Header
0x4D, 0x4 3,0x15
Comm and
0x24
ID
Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
ERR 0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.16 > Sound Select Control
• Function
MCS
Multi-display Control Module Panel
The computer switches the sound setting of the LCD display
The PIP function may or not be available on a particular LCD dis play depending on the model selected
• Set Sound
Header
0x0 6, 0x4D,0x43
Command
0x2 5
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
S.S el 0x00 0 x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
S.Sel : The sound s elec t code for the LCD display
0x01 Main
0x02 P IP
• Ack
He ader
0x4D, 0x43 ,0x06
Co mmand
0x25
ID
Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
S.Sel
0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
• Nak
He ader
0x4D, 0x43 ,0x15
Co mmand
0x25
ID
Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
ERR 0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.17 > Contrast Control
• Function
The com puter adjusts the c ontrast of the LCD display
• Set Contrast
Header Command
MCS
Multi-display Control Module Panel
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6 Footer
0x06, 0x4D,0x43 0x2 6
ID
ContV 0x00 0x0 0 0x00 0x00 0x00
Checksum
0x0D, 0x0A
ContV : The contras t value code for the LCD display ( 0~ 100 )
• Ack
Header
0x4D, 0x4 3,0x06
Comm and
0x26
ID
Val 1
ContV
Val 2
0x0 0
Va l 3
0x00
Val 4
0x00
Val 5
0x00
Val 6
0x00
Checksum
Footer
0x0D, 0x0A
• Nak
Header
0x4D, 0x4 3,0x15
Comm and
0x26
ID
Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
ERR 0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.18 > Brightness Control
• Function
The computer adjusts the brightness of the LCD display
• Set Brightness
Header
0x06, 0x4D,0x43
Command
0x27
ID
Val 1
Bright
Val 2
0x00
Val 3
0 x00
MCS
Multi-display Control Module Panel
Val 4
0x00
Val 5
0x0 0
Val 6
0x00
Checksum
Footer
0x0D, 0x0A
Bright : The brightness value code for the LCD dis play ( 0~ 100 )
• Ack
Header Command
0x4D, 0x43,0x06 0x27
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
Bright 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
• Nak
Header
0x4D, 0x43,0x15
Command
0x27
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
ERR 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
MCS
Multi-display Control Module Panel
< 2.19 > Auto Adjust Control
• Function
Auto adjusts the VGA picture position on the screen
Available only when input sour ce is VGA
• Set Auto A dust
Header
0x06, 0 x4D,0x43
Command
0x28
ID
Val 1
A.Adj
Val 2
0x00
Val 3
0x00
Val 4
0x00
Val 5
0x00
Val 6
0x00
Checksum
Footer
0x0D, 0 x0A
A.Adj : The auto adjust code for the LCD display ( 0x00 )
• Ack
Header Comm and Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
0x4D, 0x4 3,0x06 0x28
ID
A.Adj
0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
• Nak
Header
0x4D, 0x4 3,0x15
Comm and
0x28
ID
Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
ERR 0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.20 > Power Control
• Function
MCS
Multi-display Control Module Panel
The computer switches the power for the screen of LCD display
• Set Power
Header
0x0 6, 0x4D,0x43
Command
0x45
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Va l 6
Power 0x00 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0 x0A
Power : The power code for the s creen of LCD display
0x00 Power OFF
0x01 Power ON
• Ack
He ader
0x4D, 0x43 ,0x06
Co mmand
0x45
ID
Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
Power 0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
• Nak
He ader
0x4D, 0x43 ,0x15
Co mmand
0x45
ID
Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
ERR 0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.21 > PIP Control
• Function
The computer turns the PIP function of the LCD display.
The PIP function may or not be available on a particular LCD display depending on the m odel selected
• Set PIP Control
Head er
0x06, 0x4D,0x43
Command
0x50
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
P IP 0x00 0x00 0x00 0x00 0x00
Checksum
Foo ter
0x0D, 0x0 A
PIP : The PIP function code for the LCD display
0x10 PIP OFF
0x11 Small
0x12 Large
0x13 S ide by side
• Ack
Header
0x4D, 0x43,0x06
Command
0x50
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
Checksum
PIP 0x00 0x00 0x00 0x00 0 x00
Footer
0x0D, 0 x0A
• Nak
Header
0x4D, 0x43,0x15
Command
0x50
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
ERR 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
< 2.22 > PIP Source Control
• Function
The computer adjusts the PIP source of the LCD display
The PIP function may or not be available on a particular LCD display depending on the model selected
Available only when PIP function is ON
• Set PIP Source
Header
0x06, 0 x4D,0x43
Comm and
0x51
ID
Val 1 Val 2 Val 3 Val 4 Va l 5 Val 6
P.S our 0x00 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
P.Sour : The PIP source code for the LCD display
0x10 VGA
0x11 S-Video
0x12 Composite
0x13 DVI-D
0x14 HDMI
0x15 SDI
0x16 YPbP r
0x17 TV
• Ack
Heade r
0x4D, 0x43,0x06
Comm and
0x51
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
P.Sour
0x00 0x00 0x00 0x00 0x00
Check- sum
Footer
0x0D, 0x0A
• Nak
Heade r
0x4D, 0x43,0x15
Comm and
0x51
ID
Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
Checksum
ERR 0x0 0 0x00 0x00 0x00 0x00
Footer
0x0D, 0x0A
< 2.22 > PIP Source Control
**The PIP is operable in the following table:
PIP
Main
VGA S-Video
Comp os- ite
VGA X O O
S-Video O X X
Composite O X X
DVI-D O O O
HDMI O O O
SDI O O O
YPbPr O O O
TV O X X
DVI-D
O
O
O
X
X
O
O
O
MCS
Multi-display Control Module Panel
HDMI
O
O
O
X
X
O
O
O
SDI
O
O
O
O
O
X
X
O
YPbPr
O
O
O
O
O
X
X
O
TV
O
X
X
O
O
O
O
X
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
MCS
Multi-display Control Module Panel
< 2.23 > PIP Swap Control
• Function
The computer swaps the main screen with PIP screen
The PIP function may or not be available on a particular LCD display depending on the model selected
Available only when the PIP function is ON
• Set PIP Swap
Header
0x06, 0 x4D,0x43
Comm and
0x52
ID
Val 1 Val 2 Val 3 Val 4 Va l 5 Val 6
P.Swp
0x00 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
P.Swp : 0x00 ( always )
• Ack
Heade r
0x4D, 0x43,0x06
Comm and
0x52
ID
Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
P.S wp 0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
• Nak
Heade r
0x4D, 0x43,0x15
Comm and
0x52
ID
Val 1 Val 2 Va l 3 Val 4 Val 5 Val 6
ERR 0x0 0 0x00 0x00 0x00 0x00
Checksum
Footer
0x0D, 0x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
< 2.24 > PIP Location Control
• Function
The computer adjusts the PIP position of the display
MCS
Multi-display Control Module Panel
The PIP function may or not be available on a particular LCD display depending on the m odel selected
Available only when the PIP is in sm all or large size state
• Set PIP location
Head er
0x06, 0x4D,0x43
Command
0x53
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
P.Loc
0x00 0x00 0x00 0x00 0x00
Checksum
Foo ter
0x0D, 0x0 A
P.Loc : The PIP location code for the LCD display
0x10 Upper Left
0x11 Upper Right
0x12 Lower Left
0x13 Lower Right
• Ack
Header
0x4D, 0x43,0x06
Command
0x53
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
P.Loc
0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
• Nak
Header
0x4D, 0x43,0x15
Command
0x53
ID
Val 1 Val 2 Val 3 Val 4 Val 5 Val 6
ERR 0x00 0x00 0x00 0x00 0 x00
Checksum
Footer
0x0D, 0 x0A
14628 Central Ave,
Chino, CA 91710 tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project