Savin DSc432 Operating instructions

Savin DSc432 Operating instructions
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=188 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 7.520000 mm
Operating Instructions
General Settings Guide
Getting Started
Combined Function Operations
Document Server
User Tools (System Settings)
Registering Addresses and Users for Facsimile/Scanner Functions
Troubleshooting
Remarks
Entering Text
Specifications
Type for C2410/DSc424/LD124c/Aficio 3224C
Type for C3210e/DSc432/LD132c/Aficio 3232C
Printed in China
EN USA B156-7505B
B1567505B
Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety
Information in this manual before using the machine.
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=188 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 7.520000 mm
Introduction
This manual contains detailed instructions and notes on the operation and use of this machine. For your
safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy
place for quick reference.
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a means POWER ON.
b means POWER OFF.
cmeans STAND BY.
For safe and correct use of this machine, please be sure to read the Safety Information before you use
it.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
Notes:
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Laser Safety:
CDRH Regulations
This equipment complies with requirements of 21 CFR Subchapter J for class 1 laser products. This
equipment contains two AlGalnP laser diodes, 7–milliwatt, 653–659 nanometer wavelength for each
emitter. This equipment does not emit hazardous light, since the beam is totally enclosed during all customer modes of operation and maintenance.
Caution:
Use of controls or adjustments or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Notes:
The model names of the machines do not appear in the following pages. Check the type of your machine before reading this manual. (For details, see P.18 “Machine Types”.)
•
Type 1: C2410/DSc424/LD124c/Aficio 3224C
•
Type 2: C3210e/DSc432/LD132c/Aficio 3232C
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the inch version.
For good copy quality, the supplier recommends that you use genuine toner from the supplier.
The supplier shall not be responsible for any damage or expense that might result from the use of parts
other than genuine parts from the supplier with your office products.
Power Source
120V, 60Hz, 12A or more
Please be sure to connect the power cord to a power source as shown above. For details about power
source, see P.145 “Power Connection”.
Copyright © 2005
ThemisC1_EN_zentai_pre_FM.book Page i Thursday, June 30, 2005 8:21 PM
Manuals for This Machine
The following manuals describe the operational procedures of this machine. For
particular functions, see the relevant parts of the manual.
Note
❒ Manuals provided are specific to machine type.
❒ Adobe Acrobat Reader/Adobe Reader is necessary to view the manuals as a
PDF file.
❒ Two CD-ROMs are provided:
• CD-ROM 1 “Operating Instructions”
• CD-ROM 2 “Scanner Driver and Document Management Utility”
❖ General Settings Guide (this manual)
Provides an overview of the machine and describes System Settings (such as
Tray Paper Settings), Document Server functions, and troubleshooting.
Refer to this manual for Address Book procedures such as registering fax
numbers, e-mail addresses, and user codes.
❖ Security Reference
This manual is for administrators of this machine. It describes security functions that the administrators can use to protect data from being tampered, or
prevent the machine from unauthorized use.
Also refer to this manual for the procedures for registering administrators, as
well as setting user and administrator authentication.
❖ Network Guide (PDF file - CD-ROM1)
Provides information about configuring and operating the printer in a network environment or using software.
This manual covers all models, and therefore contains functions and settings
that may not be available for your model. Images, illustrations, functions, and
supported operating systems may differ from those of your model.
❖ Copy Reference
Describes operations, functions, and troubleshooting for the machine's copier
function.
❖ Facsimile Reference <Basic Features>
Describes operations, functions, and troubleshooting for the machine's facsimile function.
❖ Facsimile Reference <Advanced Features>
Describes advanced facsimile functions such as line settings and procedures
for registering IDs.
❖ Printer Reference
Describes system settings, operations, functions, and troubleshooting for the
machine's printer function.
i
ThemisC1_EN_zentai_pre_FM.book Page ii Thursday, June 30, 2005 8:21 PM
❖ Scanner Reference (PDF file - CD-ROM1)
Describes operations, functions, and troubleshooting for the machine's scanner function.
❖ Manuals for DeskTopBinder Lite
DeskTopBinder Lite is a utility included on the CD-ROM labeled “Scanner
Driver and Document Management Utility”.
• DeskTopBinder Lite Setup Guide (PDF file - CD-ROM2)
Describes installation of, and the operating environment for DeskTopBinder Lite in detail. This guide can be displayed from the [Setup] display
when DeskTopBinder Lite is installed.
• DeskTopBinder Introduction Guide (PDF file - CD-ROM2)
Describes operations of DeskTopBinder Lite and provides an overview of
its functions. This guide is added to the [Start] menu when DeskTopBinder
Lite is installed.
• Auto Document Link Guide (PDF file - CD-ROM2)
Describes operations and functions of Auto Document Link installed with
DeskTopBinder Lite. This guide is added to the [Start] menu when DeskTopBinder Lite is installed.
❖ Other manuals
• PS3 Supplement (PDF file - CD-ROM1)
• Unix Supplement (Available from an authorized dealer, or as a PDF file on
our Web site.)
ii
ThemisC1_EN_zentai_pre_FM.book Page iii Thursday, June 30, 2005 8:21 PM
What You Can Do with This Machine
The following introduces the functions of this machine, and the relevant manuals containing detailed information about them.
Products marked with * are optional. For details about optional products, see
p.162 “Options”, or contact your local dealer.
Copier, Facsimile, Printer, and
Scanner Functions
Utilizing Stored Documents
AFS015S
AFS014S
This machine provides copier, facsimile*, printer, and scanner functions.
• You can make copies of originals.
With a finisher*, you can sort and
staple copies. See Copy Reference.
• You can send originals by fax and
receive faxes from other parties.
See Facsimile Reference <Basic Features> , and Facsimile Reference
<Advanced Features>.
• You can print documents created
using applications. See Printer Reference.
• You can scan originals and send
the scan file to a computer. See
Scanner Reference.
• You can store file from originals
scanned by this machine, or file
sent from other computers, into
the machine's hard disk. You can
print and fax stored documents as
required. You can also change
print settings and print multiple
documents (Document Server).
See p.39 “Using the Document
Server”.
• With DeskTopBinder Professional*/Lite, you can search, check,
print, and delete stored documents
using your computer. You can also
retrieve stored documents scanned
in scanner mode. With File Format
Converter*, you can even download documents stored in copy and
printer functions to your computer. See Network Guide.
iii
ThemisC1_EN_zentai_pre_FM.book Page iv Thursday, June 30, 2005 8:21 PM
Paperless Fax Transmission
and Reception
Fax Transmission and
Reception Through the
Internet
Reception
AFS018S
AFS016S
• You can store received fax messages on the machine's hard disk, instead of printing them onto paper.
You can use DeskTopBinder Professional*/Lite or a Web browser
to check, print, delete, retrieve, or
download documents using your
computer (Storing received documents). See Facsimile Reference
<Advanced Features>.
Transmission
AFS017S
• You can send documents created
using applications to another party's fax machine directly, without
performing a print job (LAN-Fax).
See Facsimile Reference <Advanced
Features>.
iv
• You can send fax documents through
e-mail by specifying the recipient's
e-mail address (Internet Fax Transmission).
You can receive sent documents
via Internet Fax, or from computers (Internet Fax Reception). See
Facsimile Reference <Basic Features>.
• You can send faxes by using data
such as the IP address to specify
the IP-Fax destination (IP-Fax
Transmission).
The transmitted files can be received using an Internet fax machine (IP-Fax Reception). See
Facsimile Reference <Basic Features>.
ThemisC1_EN_zentai_pre_FM.book Page v Thursday, June 30, 2005 8:21 PM
Using the Scanner in a
Network Environment
Administrating the
Machine/Protecting
Documents (Security
Functions)
AFS019S
• You can send scanned documents
to other network computers using
e-mail (Sending stored scan file by
e-mail). See Scanner Reference.
• With ScanRouter delivery software, you can save scanned documents in specified destinations on
network computers (File storage).
See Scanner Reference.
• You can send scanned documents
to other network folders (Scan to
Folder). See Scanner Reference.
AFS020S
• You can protect documents from
unauthorized access and stop
them from being copied without
permission. See Security Reference.
• You can control the use of the machine, as well as prevent machine
settings from being changed without authorization. See Security Reference.
• By setting passwords, you can prevent unauthorized access via the
network. See Security Reference.
• You can erase the data on the hard
disk to prevent the information
from leaking out. See the manual
for the DataOverWriteSecurity
Unit* and Security Reference.
v
ThemisC1_EN_zentai_pre_FM.book Page vi Thursday, June 30, 2005 8:21 PM
Monitoring the Machine Via
Computer
AFS021S
You can monitor machine status and
change settings using a computer.
• Using SmartDeviceMonitor for Admin, SmartDeviceMonitor for Client, or a Web browser, you can use
a computer to view the machine's
status, such as to check on paper
quantities, or misfeeds, etc. See
Network Guide.
• You can also use a Web browser to
make network settings. See Network Guide.
• You can also use a Web browser to
register and manage items such as
user codes, fax numbers, e-mail
addresses, and folders in the Address Book. See the Web browser's
Help.
vi
ThemisC1_EN_zentai_pre_FM.book Page vii Thursday, June 30, 2005 8:21 PM
TABLE OF CONTENTS
Manuals for This Machine ...................................................................................... i
What You Can Do with This Machine.................................................................. iii
Copier, Facsimile, Printer, and Scanner Functions ................................................... iii
Utilizing Stored Documents ....................................................................................... iii
Paperless Fax Transmission and Reception............................................................. iv
Fax Transmission and Reception Through the Internet ............................................ iv
Using the Scanner in a Network Environment ........................................................... v
Administrating the Machine/Protecting Documents (Security Functions) .................. v
Monitoring the Machine Via Computer...................................................................... vi
Notice ......................................................................................................................1
Copyrights and Trademarks .................................................................................4
Trademarks ................................................................................................................4
Information about Installed Software.......................................................................... 5
How to Read This Manual ................................................................................... 11
Safety Information ............................................................................................... 12
Safety During Operation........................................................................................... 12
Positions of Labels and Hallmarks for RWARNING and RCAUTION............ 15
ENERGY STAR Program ..................................................................................... 16
Machine Types ..................................................................................................... 18
1. Getting Started
Guide to Components ......................................................................................... 19
External Options....................................................................................................... 21
Internal Options........................................................................................................ 22
Control Panel........................................................................................................ 23
Display Panel ........................................................................................................... 25
When the Authentication Screen is displayed.......................................................... 25
Turning On the Power ......................................................................................... 27
Turning On the Main Power ..................................................................................... 27
Turning On the Power .............................................................................................. 27
Turning Off the Power .............................................................................................. 28
Turning Off the Main Power ..................................................................................... 28
Saving Energy .......................................................................................................... 29
2. Combined Function Operations
Changing Modes .................................................................................................. 31
Multi-Access......................................................................................................... 33
3. Document Server
Relationship between Document Server and Other Functions ....................... 37
Document Server Display ........................................................................................ 38
Using the Document Server................................................................................ 39
Storing Data ............................................................................................................. 39
Changing a Stored Document's File Name, User Name, or Password.................... 42
Selecting a Document .............................................................................................. 42
Searching for Stored Documents ............................................................................. 43
vii
ThemisC1_EN_zentai_pre_FM.book Page viii Thursday, June 30, 2005 8:21 PM
Printing Stored Documents ...................................................................................... 44
Deleting Stored Documents ..................................................................................... 47
Viewing Stored Documents Using a Web Browser .................................................. 47
Downloading Stored Documents.............................................................................. 48
Settings for the Document Server...................................................................... 49
4. User Tools (System Settings)
User Tools Menu (System Settings)................................................................... 51
Accessing User Tools (System Settings) .......................................................... 54
Changing Default Settings ....................................................................................... 54
Exiting User Tools .................................................................................................... 54
Settings You Can Change with User Tools ....................................................... 55
General Features ..................................................................................................... 55
Tray Paper Settings ................................................................................................. 58
Timer Settings .......................................................................................................... 61
Administrator Tools .................................................................................................. 63
5. Registering Addresses and Users for Facsimile/Scanner
Functions
Address Book....................................................................................................... 69
Registering Names .............................................................................................. 72
Registering a Name ................................................................................................. 72
Changing a Registered Name.................................................................................. 72
Deleting a Registered Name .................................................................................... 73
Authentication Information ................................................................................. 74
Registering a New User Code.................................................................................. 74
Changing a User Code............................................................................................. 75
Deleting a User Code............................................................................................... 75
Displaying the Counter for Each User Code ............................................................ 76
Printing the Counter for Each User Code................................................................. 76
Clearing the Number of Prints.................................................................................. 77
Fax Destination .................................................................................................... 78
Registering a Fax Destination .................................................................................. 79
Changing a Registered Fax Destination .................................................................. 81
Deleting a Registered Fax Destination..................................................................... 82
Registering an IP-Fax Destination ........................................................................... 83
Changing a Registered IP-Fax Destination.............................................................. 84
Deleting a Registered IP-Fax Destination ................................................................ 85
E-mail Destination................................................................................................ 86
Registering an E-mail Destination ............................................................................ 86
Changing a Registered E-mail Destination .............................................................. 87
Deleting a Registered E-mail Destination ................................................................ 88
Registering Folders ............................................................................................. 89
Using SMB to Connect............................................................................................. 89
Using FTP to Connect.............................................................................................. 93
Registering Names to a Group ........................................................................... 96
viii
Registering a New Group ......................................................................................... 96
Registering Names to a Group................................................................................. 97
Displaying Names Registered in Groups ................................................................. 97
Removing a Name from a Group ............................................................................. 98
ThemisC1_EN_zentai_pre_FM.book Page ix Thursday, June 30, 2005 8:21 PM
Changing a Group Name ......................................................................................... 98
Deleting a Group ...................................................................................................... 99
Adding a Group to Another Group ........................................................................... 99
Deleting a Group within a Group.............................................................................. 99
Registering a Protection Code ......................................................................... 101
Registering a Protection Code To a Single User ...................................................101
Registering a Protection Code To a Group User ...................................................102
Registering the Transfer Request .................................................................... 103
Registering a Transfer Station/Receiving Station .................................................. 103
Changing a Registered Transfer Station/Receiving Station ...................................105
Deleting a Registered Transfer Station/Receiving Station .....................................106
Registering Authentication ............................................................................... 107
SMTP Authentication .............................................................................................107
LDAP Authentication ..............................................................................................108
6. Troubleshooting
If Your Machine Does Not Operate As You Want............................................ 109
General ..................................................................................................................109
Printing Problems...................................................................................................112
Document Server ...................................................................................................113
Maintenance...........................................................................................................113
BLoading Paper ................................................................................................ 114
Loading Paper into Tray 1 and 2............................................................................114
Loading Paper into Tray 3 and 4 (optional)............................................................ 114
Loading Paper into Large Capacity Tray (optional)................................................115
DAdding Toner.................................................................................................. 117
Removing/Inserting Toner......................................................................................118
xClearing Misfeeds .......................................................................................... 121
Changing the Paper Size................................................................................... 126
Changing the Paper Size of Tray 1 and 2 ..............................................................126
Changing the Paper Size of Tray 3 and 4 (option).................................................128
If you load a paper size that is not selected automatically .....................................129
d Adding Staples.............................................................................................. 131
500-Sheet Finisher.................................................................................................131
1000-Sheet Finisher...............................................................................................132
e Removing Jammed Staples ......................................................................... 134
500-Sheet Finisher.................................................................................................134
1000-Sheet Finisher...............................................................................................135
Replacing the Stamp Cartridge ........................................................................ 137
Auto Color Calibration....................................................................................... 138
7. Remarks
Dos and Don'ts................................................................................................... 141
Saving Color Copies.......................................................................................... 142
Toner ................................................................................................................... 143
Handling Toner.......................................................................................................143
Toner Storage ........................................................................................................143
Used Toner ............................................................................................................143
ix
ThemisC1_EN_zentai_pre_FM.book Page x Thursday, June 30, 2005 8:21 PM
Where to Put Your Machine .............................................................................. 144
Machine Environment ............................................................................................144
Moving....................................................................................................................144
Power Connection..................................................................................................145
Access to the Machine ...........................................................................................145
Maintaining Your Machine ................................................................................ 146
Cleaning the Exposure Glass.................................................................................146
Cleaning the ADF...................................................................................................146
Cleaning the Guide Boards ....................................................................................146
Cleaning and Adjusting Internal Parts ....................................................................147
Cleaning the Dustproof Glass ................................................................................ 148
Other Functions ................................................................................................. 149
Inquiry ....................................................................................................................149
Changing the Display Language ............................................................................149
Changing Paper Thickness Settings ...................................................................... 150
Counter ............................................................................................................... 151
Displaying the Total Counter..................................................................................151
8. Entering Text
Entering Text ...................................................................................................... 153
Available Characters ..............................................................................................153
Keys .......................................................................................................................153
How to Enter Text ..................................................................................................154
9. Specifications
Mainframe ........................................................................................................... 155
ADF ........................................................................................................................ 160
Duplex Unit.............................................................................................................160
Bypass Tray ...........................................................................................................161
Options ............................................................................................................... 162
500-Sheet Finisher.................................................................................................162
1000-Sheet Finisher...............................................................................................163
Bridge Unit .............................................................................................................164
Shift Sort Tray ........................................................................................................164
Internal tray 2 (1 bin tray) .......................................................................................165
Large Capacity Tray (LCT).....................................................................................165
Paper tray unit........................................................................................................166
Copy Paper ......................................................................................................... 167
Recommended Paper Sizes and Types.................................................................167
Non-recommended Paper......................................................................................171
Paper Storage ........................................................................................................172
INDEX....................................................................................................... 173
x
ThemisC1_EN_zentai_pre_FM.book Page 1 Thursday, June 30, 2005 8:21 PM
Notice
Notice To Wireless LAN Interface (option) Users
Notes to users
It is strictly forbidden to use antenna(s) except designated.
A The antenna(s) of this device must not be co-located or operating in conjunction with any other antenna or transmitter.
B This equipment complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance.
Notes to users in the United States of America
Notice:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Warning
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
1
ThemisC1_EN_zentai_pre_FM.book Page 2 Thursday, June 30, 2005 8:21 PM
Note to users in Canada
Note:
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the
device.
IEEE 802.11b Interface Unit Type H:
This device complies with RSS-210 of Industry Canada.
The term “IC:” before the certification/registration number only signifies that
the Industry Canada technical specifications were met.
To prevent radio interference to the licensed service, this device is intended to
be operated indoors and away from windows to provide maximum shielding.
Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power (EIRP)
is not more than that required for successful communication.
This device has been designed to operate with an antenna having a maximum
gain of [0.45] dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is [50] ohms.
Remarque concernant les utilisateurs au Canada
Avertissement:
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
L'utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1)
il ne doit pas produire de brouillage et (2) l'utilisateur du dispositif doit être prêt
á accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
IEEE 802.11b Interface Unit Type H:
Ce dispositif est conforme á la norme CNR-210 d'Industrie Canada.
L'expression «IC:» avant le numéro d'homologation/enregistrement signifie
seulement que les spécifications techniques d'Industrie Canada ont été respectées.
Pour empêcher que cet appareil cause du brouillage au service faisant l'objet
d'une licence, il doit être utilisé á l'intérieur et devrait être placé loin des fenêtres
afin de fournir un écran de blindage maximal.
Si le matériel (ou son antenne d'emission) est installe á l'extérieur, il doit faire
l'objet d'une licence.
2
ThemisC1_EN_zentai_pre_FM.book Page 3 Thursday, June 30, 2005 8:21 PM
Afin de réduire le risque d'interférence aux autres utilisateurs, le type d'antenne
et son gain doivent être choisis de façon á ce que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne soit pas supérieure au niveau requis pour obtenir une
communication satisfaisante.
Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de [0.45] dBi.Une antenne ayant un gain plus élevé est strictement interdite
par les réglements d'Industrie Canada.L'impédance d'antenne requise est [50]
ohms.
3
ThemisC1_EN_zentai_pre_FM.book Page 4 Thursday, June 30, 2005 8:21 PM
Copyrights and Trademarks
Trademarks
Microsoft®, Windows® and Windows NT® are registered trademarks of Microsoft Corporation in the United States and/or other countries.
Acrobat® is a registered trademark of Adobe Systems Incorporated.
Bluetooth™ is a trademark of the Bluetooth SIG, Inc. (Special Interest Group)
and is used by RICOH Company Limited under license.
Copyright ©2001 Bluetooth SIG, Inc.
The Bluetooth Trademarks are owned by Bluetooth SIG, Inc. USA
Other product names used herein are for identification purposes only and might
be trademarks of their respective companies. We disclaim any and all rights to
those marks.
The proper names of the Windows operating systems are as follows:
• The product name of Windows® 95 is Microsoft® Windows® 95
• The product name of Windows® 98 is Microsoft® Windows® 98
• The product name of Windows® Me is Microsoft® Windows® Millennium
Edition (Windows Me)
• The product names of Windows® 2000 are as follows:
Microsoft® Windows® 2000 Advanced Server
Microsoft® Windows® 2000 Server
Microsoft® Windows® 2000 Professional
• The product names of Windows® XP are as follows:
Microsoft® Windows® XP Professional
Microsoft® Windows® XP Home Edition
• The product names of Windows Server™ 2003 are as follows:
Microsoft® Windows Server™ 2003 Standard Edition
Microsoft® Windows Server™ 2003 Enterprise Edition
Microsoft® Windows Server™ 2003 Web Edition
• The product names of Windows® NT are as follows:
Microsoft® Windows NT® Server 4.0
Microsoft® Windows NT® Workstation 4.0
4
ThemisC1_EN_zentai_pre_FM.book Page 5 Thursday, June 30, 2005 8:21 PM
Information about Installed Software
expat
• The software including controller, etc. (hereinafter "software") installed on
this product uses the expat Version under the conditions mentioned below.
• The product manufacturer provides warranty and support to the software of
the product including the expat, and the product manufacturer makes the initial developer and copyright holder of the expat, free from these obligations.
• Information relating to the expat is available at:
http://expat.sourceforge.net/
Copyright © 1998, 1999, 2000 Thai Open Source Software Center, Ltd. and Clark
Cooper.
Copyright © 2001, 2002 Expat maintainers.
Permission is hereby granted, free of charge, to any person obtaining a copy of
this software and associated documentation files (the "Software"), to deal in the
Software without restriction, including without limitation the rights to use,
copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all
copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION
WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
NetBSD
1. Copyright Notice of NetBSD
For all users to use this product:
This product contains NetBSD operating system:
For the most part, the software constituting the NetBSD operating system is not
in the public domain; its authors retain their copyright.
The following text shows the copyright notice used for many of the NetBSD
source code. For exact copyright notice applicable for each of the files/binaries,
the source code tree must be consulted.
A full source code can be found at http://www.netbsd.org/.
Copyright © 1999, 2000 The NetBSD Foundation, Inc.
All rights reserved.
5
ThemisC1_EN_zentai_pre_FM.book Page 6 Thursday, June 30, 2005 8:21 PM
6
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
A Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
B Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
C All advertising materials mentioning features or use of this software must
display the following acknowledgment:
This product includes software developed by The NetBSD Foundation, Inc.
and its contributors.
D Neither the name of The NetBSD Foundation nor the names of its contributors may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND
CONTRIBUTORS ''AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
2.Authors Name List
All product names mentioned herein are trademarks of their respective owners.
The following notices are required to satisfy the license terms of the software
that we have mentioned in this document:
• This product includes software developed by the University of California,
Berkeley and its contributors.
• This product includes software developed by Jonathan R. Stone for the NetBSD Project.
• This product includes software developed by the NetBSD Foundation, Inc.
and its contributors.
• This product includes software developed by Manuel Bouyer.
• This product includes software developed by Charles Hannum.
• This product includes software developed by Charles M. Hannum.
• This product includes software developed by Christopher G. Demetriou.
• This product includes software developed by TooLs GmbH.
• This product includes software developed by Terrence R. Lambert.
• This product includes software developed by Adam Glass and Charles Hannum.
• This product includes software developed by Theo de Raadt.
ThemisC1_EN_zentai_pre_FM.book Page 7 Thursday, June 30, 2005 8:21 PM
• This product includes software developed by Jonathan Stone and Jason R.
Thorpe for the NetBSD Project.
• This product includes software developed by the University of California,
Lawrence Berkeley Laboratory and its contributors.
• This product includes software developed by Christos Zoulas.
• This product includes software developed by Christopher G. Demetriou for
the NetBSD Project.
• This product includes software developed by Paul Kranenburg.
• This product includes software developed by Adam Glass.
• This product includes software developed by Jonathan Stone.
• This product includes software developed by Jonathan Stone for the NetBSD
Project.
• This product includes software developed by Winning Strategies, Inc.
• This product includes software developed by Frank van der Linden for the
NetBSD Project.
• This product includes software developed for the NetBSD Project by Frank
van der Linden
• This product includes software developed for the NetBSD Project by Jason R.
Thorpe.
• The software was developed by the University of California, Berkeley.
• This product includes software developed by Chris Provenzano, the University of California, Berkeley, and contributors.
Sablotron
Sablotron (Version 0.82) Copyright © 2000 Ginger Alliance Ltd. All Rights Reserved
a) The application software installed on this product includes the Sablotron software Version 0.82 (hereinafter, "Sablotron 0.82"), with modifications made by
the product manufacturer. The original code of the Sablotron 0.82 is provided by
Ginger Alliance Ltd., the initial developer, and the modified code of the Sablotron 0.82 has been derived from such original code provided by Ginger Alliance
Ltd.
b) The product manufacturer provides warranty and support to the application
software of this product including the Sablotron 0.82 as modified, and the product manufacturer makes Ginger Alliance Ltd., the initial developer of the Sablotron 0.82, free from these obligations.
c) The Sablotron 0.82 and the modifications thereof are made available under the
terms of Mozilla Public License Version 1.1 (hereinafter, "MPL 1.1"), and the application software of this product constitutes the "Larger Work" as defined in
MPL 1.1. The application software of this product except for the Sablotron 0.82
as modified is licensed by the product manufacturer under separate agreement(s).
d) The source code of the modified code of the Sablotron 0.82 is available at: http://support-download.com/services/device/sablot/notice082.html
7
ThemisC1_EN_zentai_pre_FM.book Page 8 Thursday, June 30, 2005 8:21 PM
e) The source code of the Sablotron software is available at: http://www.gingerall.com
f) MPL 1.1 is available at: http://www.mozilla.org/MPL/MPL-1.1.html
JPEG LIBRARY
• The software installed on this product is based in part on the work of the Independent JPEG Group.
SASL
CMU libsasl
Tim Martin
Rob Earhart
Rob Siemborski
Copyright © 2001 Carnegie Mellon University. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
A Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
B Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
C The name "Carnegie Mellon University" must not be used to endorse or promote products derived from this software without prior written permission.
For permission or any other legal details, please contact:
Office of Technology Transfer
Carnegie Mellon University
5000 Forbes Avenue
Pittsburgh, PA 15213-3890
(412) 268-4387, fax: (412) 268-7395
[email protected]
D Redistributions of any form whatsoever must retain the following acknowledgment:
"This product includes software developed by Computing Services at Carnegie Mellon University (http://www.cmu.edu/computing/)."
CARNEGIE MELLON UNIVERSITY DISCLAIMS ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL CARNEGIE
MELLON UNIVERSITY BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING
FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF
CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT
OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS
SOFTWARE.
8
ThemisC1_EN_zentai_pre_FM.book Page 9 Thursday, June 30, 2005 8:21 PM
MD4
Copyright © 1990-2, RSA Data Security, Inc. All rights reserved.
License to copy and use this software is granted provided that it is identified as
the "RSA Data Security, Inc. MD4 Message-Digest Algorithm" in all material
mentioning or referencing this software or this function.
License is also granted to make and use derivative works provided that such
works are identified as "derived from the RSA Data Security, Inc. MD4 MessageDigest Algorithm" in all material mentioning or referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or the suitability of this software for any particular
purpose. It is provided "as is" without express or implied warranty of any kind.
These notices must be retained in any copies of any part of this documentation
and/or software.
MD5
Copyright © 1991-2, RSA Data Security, Inc. Created 1991. All rights reserved.
License to copy and use this software is granted provided that it is identified as
the "RSA Data Security, Inc. MD5 Message-Digest Algorithm" in all material
mentioning or referencing this software or this function.
License is also granted to make and use derivative works provided that such
works are identified as "derived from the RSA Data Security, Inc. MD5 MessageDigest Algorithm" in all material mentioning or referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or the suitability of this software for any particular
purpose. It is provided "as is" without express or implied warranty of any kind.
These notices must be retained in any copies of any part of this documentation
and/or software.
9
ThemisC1_EN_zentai_pre_FM.book Page 10 Thursday, June 30, 2005 8:21 PM
Samba(Ver 2.2.2-ja-1.1)
For SMB transmission, this machine uses Samba ver 2.2.2-ja-1.1 (hereinafter referred to as Samba 2.2.2-ja-1.1).
Copyright © Andrew Tridgell 1994-1998
This program is free software; you can redistribute it and/or modify it under the
terms of the GNU General Public License as published by the Free Software
Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT
ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
License for more details.
You should have received a copy of the GNU General Public License along with
this program; if not, write to the Free Software Foundation, Inc., 675 Mass Ave,
Cambridge, MA 02139, USA
Note
❒ The source code for SMB transmission by this machine can be downloaded
from the following website:
http://support-download.com/services/scbs
RSA BSAFE®
• This product includes RSA BSAFE® cryptographic or security protocol software from RSA Security Inc.
• RSA and BSAFE are registered trademarks of RSA Security Inc. in the United
States and/or other countries.
• RSA Security Inc. All rights reserved.
10
ThemisC1_EN_zentai_pre_FM.book Page 11 Thursday, June 30, 2005 8:21 PM
How to Read This Manual
Symbols
This manual uses the following symbols:
R WARNING:
This symbol indicates a potentially hazardous situation that might result in
death or serious injury if you misuse the machine by not following the instructions under this symbol. Be sure to read the instructions, all of which are included in the Safety Information section in the General Settings Guide.
R CAUTION:
This symbol indicates a potentially hazardous situation that might result in minor or moderate injury or property damage not involving bodily injury, if you
misuse the machine by not following these instructions under this symbol. Be
sure to read the instructions, all of which are included in the Safety Information
section in the General Settings Guide.
* WARNINGS and CAUTIONS are notes for your safety.
Important
If these instructions are not followed, paper might be misfed, originals damaged, or data lost. Be sure to read these instructions.
Preparation
This symbol indicates the prior knowledge or preparation required before operation.
Note
This symbol indicates precautions for operation, or actions to be taken following
user error.
Limitation
This symbol indicates numerical limits, functions that cannot be used together,
or conditions under which a particular function cannot be used.
Reference
This symbol indicates where further relevant information can be found.
[
]
Keys that appear on the machine's display panel.
{
}
Keys built into the machine's control panel.
11
ThemisC1_EN_zentai_pre_FM.book Page 12 Thursday, June 30, 2005 8:21 PM
Safety Information
When using this machine, the following safety precautions should always be followed.
Safety During Operation
In this manual, the following important symbols are used:
R WARNING:
Indicates a potentially hazardous situation which, if instructions
are not followed, could result in death or serious injury.
R CAUTION:
Indicates a potentially hazardous situation which, if instructions are not
followed, may result in minor or moderate injury or damage to property.
R WARNING:
• Connect the power cord directly into a wall outlet and never use an extension cord.
• Disconnect the power plug (by pulling the plug, not the cable) if the
power cable or plug becomes frayed or otherwise damaged.
• To avoid hazardous electric shock or laser radiation exposure, do not
remove any covers or screws other than those specified in this manual.
• Turn off the power and disconnect the power plug (by pulling the plug,
not the cable) if any of the following occurs:
• You spill something into the machine.
• You suspect that your machine needs service or repair.
• The external housing of your machine has been damaged.
• Do not incinerate spilled toner or used toner. Toner dust might ignite
when exposed to an open flame.
• Disposal can take place at our authorized dealer.
• Dispose of the used toner bottle in accordance with the local regulations.
• Keep the machine away from flammable liquids, gases, and aerosols.
A fire or an electric shock might occur.
• Connect the machine only to the power source described on the inside
front cover of this manual. Connect the power cord directly into a wall
outlet and do not use an extension cord.
• Do not damage, break or make any modifications to the power cord.
Do not place heavy objects on it. Do not pull it hard nor bend it more
than necessary. These actions could cause an electric shock or fire.
12
ThemisC1_EN_zentai_pre_FM.book Page 13 Thursday, June 30, 2005 8:21 PM
R CAUTION:
• Protect the machine from dampness or wet weather, such as rain and snow.
• Keep the machine away from humidity and dust. Otherwise a fire or an electric shock might occur.
• Do not place the machine on an unstable or tilted surface. If it topples over,
an injury might occur.
• If you use the machine in a confined space, make sure there is a continuous
air turnover.
• Unplug the power cord from the wall outlet before you move the machine.
While moving the machine, you should take care that the power cord will not
be damaged under the machine.
• When you disconnect the power plug from the wall outlet, always pull the
plug (not the cable).
• Do not allow paper clips, staples, or other small metallic objects to fall inside
the machine.
• Keep toner (used or unused) and toner bottle out of the reach of children.
• If toner or used toner is inhaled, gargle with plenty of water and move into a
fresh air environment. Consult a doctor if necessary.
• If toner or used toner gets into your eyes, flush immediately with large
amounts of water. Consult a doctor if necessary.
• If toner or used toner is swallowed, dilute by drinking a large amount of water. Consult a doctor if necessary.
• Avoid getting toner on your clothes or skin when removing a paper jam or
replacing toner. If your skin comes into contact with toner, wash the affected
area thoroughly with soap and water.
• If toner gets on your clothing, wash with cold water. Hot water will set the
toner into the fabric and may make removing the stain impossible.
• If your skin comes into contact with toner or used toner, wash the affected
area thoroughly with soap and water.
• For environmental reasons, do not dispose of the machine or expended
supply waste at household waste collection points. Disposal can take place
at an authorized dealer.
• The inside of the machine could be very hot. Do not touch the parts with a
label indicating “hot surface”. Otherwise, an injury might occur.
• The fusing section of this machine might be very hot. Caution should be taken when removing misfed paper.
• The fusing unit becomes very hot. When installing a new fuser oil unit, turn
off the machine and wait about an hour. After that, install the new fuser oil
unit. Not waiting for the unit to cool could result in a burn.
• Keep the fuser oil unit away from flames. There is a risk of fire or burns.
• Keep the waste oil bottle away from flames. There is a risk of fire or burns.
13
ThemisC1_EN_zentai_pre_FM.book Page 14 Thursday, June 30, 2005 8:21 PM
R CAUTION:
• Do not use aluminum foil, carbon paper, or similar conductive paper to avoid
a fire or machine failure.
• The inside of the machine becomes very hot. Do not touch the parts with a
label indicating "v" (means hot surface). Touching "v" (means hot surface)
could result in a burn.
14
ThemisC1_EN_zentai_pre_FM.book Page 15 Thursday, June 30, 2005 8:21 PM
Positions of Labels and Hallmarks for
RWARNING and RCAUTION
This machine has labels for RWARNING and RCAUTION at the positions
shown below. For safety, please follow the instructions and handle the machine
as indicated.
AFS001D
15
ThemisC1_EN_zentai_pre_FM.book Page 16 Thursday, June 30, 2005 8:21 PM
ENERGY STAR Program
As an ENERGY STAR Partner, we have determined
that this machine model meets the ENERGY STAR
Guidelines for energy efficiency.
The ENERGY STAR Guidelines intend to establish an international energy-saving system for
developing and introducing energy-efficient office equipment to deal with environmental issues, such as global warming.
When a product meets the ENERGY STAR Guidelines for energy efficiency, the Partner shall
place the ENERGY STAR logo onto the machine model.
This product was designed to reduce the environmental impact associated with office equipment by means of energy-saving features, such as Low-power mode.
❖ Low-Power mode
• Low Power Mode
This product automatically lowers its power consumption 15 minutes after
the last copy or print job has finished. Printing is still possible in Low Power Mode, but if you wish to make copies press the {Energy Saver}
} key first.
Reference
For details about how to change the default interval, see p.61 “Energy
Saver Timer”.
• Sleep Mode
This product automatically lowers its power consumption even further 45
minutes after the last copy or print job has finished. This function is called
“Sleep Mode”. Printing from computer or fax is possible in this mode, but
if you wish to make copies, press the operation switch first.
Reference
For details about how to change the default interval, see p.61 “Auto Off
Timer”.
❖ Duplex Priority
The ENERGY STAR Program recommends the duplex function. By conserving paper resources this function reduces a burden to the environment. For
applicable machines, duplex function (one-sided originals→two-sided copies) can be selected preferentially when the operation switch or the main power switch is turned on, the {Energy Saver}
} key is pressed, or the machine resets
automatically.
16
Reference
To change the settings of the Duplex Priority mode, see “Duplex Mode Priority”in “General Features 2/5”, Copy Reference.
ThemisC1_EN_zentai_pre_FM.book Page 17 Thursday, June 30, 2005 8:21 PM
Specifications
Type 1/Type 2
Low - Power mode
Sleep mode
Power consumption
103.8 W or less
Default interval
15 minutes
Recovery Time
26 seconds or less
Power consumption
14.8 W or less
Default interval
Duplex Priority
45 minutes
1 Sided→2 Sided
❖ Recycled Paper
In accordance with the ENERGY STAR Program, we recommend use of environmentally friendly recycled paper. Please contact your sales representative
for recommended paper.
17
ThemisC1_EN_zentai_pre_FM.book Page 18 Thursday, June 30, 2005 8:21 PM
Machine Types
This machine comes in two models which vary in copy speed. To confirm which
model you have, see the inside front cover.
18
Type 1
Type 2
Copy speed/B&W
24 copies/minute
(A4K, 81/2" × 11"K)
32 copies/minute
(A4K, 81/2" × 11"K)
Copy speed/Full Color
10 copies/minute
(A4K, 81/2" × 11"K)
10 copies/minute
(A4K, 81/2" × 11"K)
ThemisC1_EN_zentai_pre_FM.book Page 19 Thursday, June 30, 2005 8:21 PM
1. Getting Started
Guide to Components
AFT044S
1. Auto Document Feeder (ADF)
6. Control panel
Lower the ADF over originals placed on
the exposure glass. If you have the ADF,
load a stack of originals here. They will
be fed automatically, one by one.
See p.23 “Control Panel”.
2. Exposure glass
Place originals face down.
3. Internal tray
Copied, printed paper or fax messages
are delivered here.
4. Main power switch
If the machine does not operate after turning
on the operation switch, check the main power switch is turned on. If it is off, turn it on.
5. Operation switch
Press this switch to turn the power on
(the On indicator lights up). To turn the
power off, press this switch again (the On
indicator goes off).
7. Remove Paper Indicator
The indicator is lit when paper is output
to the internal tray 2 (1 bin tray). If the internal tray 2 has not been installed, the indicator does not light.
8. Internal tray 2 (1 bin tray) (optional)
9. Front cover
Open to access the inside of the machine.
10. Paper tray (upper:Tray 1, lower:Tray 2)
Load paper here.
11. Paper tray unit (optional upper:Tray3, lower:Tray4>)
Load paper here.
19
ThemisC1_EN_zentai_pre_FM.book Page 20 Thursday, June 30, 2005 8:21 PM
Getting Started
1
AFT007S
1. Ventilation holes
4. Lower right cover
Prevent overheating. Do not obstruct the
ventilation holes by placing an object
near it or leaning things against it. If the
machine overheats, a fault might occur.
Open this cover to remove misfed paper.
2. Earth Leakage Breaker
Prevents electric shock.
3. Interface for network connections
⇒Network Guide
20
5. Bypass tray
Use when copying onto OHP transparencies,label paper (adhesive labels), translucent paper, postcards, envelopes and
custom size paper.
6. Duplex unit (Unit for two-sided
copies)
ThemisC1_EN_zentai_pre_FM.book Page 21 Thursday, June 30, 2005 8:21 PM
Guide to Components
External Options
1
AFT040S
1. 500-Sheet Finisher
5. Shift sort tray
Sorts, stacks and staples copies.
Sorts and stacks copies.
2. Bridge unit
6. Paper tray unit
Relays copies to the finisher.
Consists of two paper trays.
3. Internal tray 2 (1 bin tray)
7. Large Capacity Tray (LCT)
If you select this as the output tray, copied paper will be delivered here face
down.
Holds 2000 sheets of paper.
4. 1000-Sheet Finisher
8. Interchange unit
Required when installing the internal
tray 2 (1 bin tray).
Sorts, stacks and staples copies.
*1 : Finisher proof tray
*2 : Finisher shift tray
Note
❒ When you use the 1000-Sheet Finisher, the adjustment table is required.
21
ThemisC1_EN_zentai_pre_FM.book Page 22 Thursday, June 30, 2005 8:21 PM
Getting Started
Internal Options
A
1
B
C
D
E
F
G
*1
22
Fax unit
Allows you to use the facsimile function.
IEEE 1394 Interface Board *1
Connects to an IEEE 1394 cable.
Bluetooth *1
Allows you to expand the interface.
File Format Converter
Allows you to download documents from the Document Server stored by
copier and printer functions. See p.48 “Downloading Stored Documents”.
IEEE 802.11b Wireless LAN Board *1
You can install a wireless LAN interface.
IEEE 1284 Interface Board *1
Connects to an IEEE 1284 cable.
DataOverWriteSecurity Unit
Allows you to erase data on the hard disk.
You cannot install two or more of the options below:
IEEE 1394 interface board, IEEE 802.11b Wireless LAN Board, IEEE 1284 Interface
Board, Bluetooth.
ThemisC1_EN_zentai_pre_FM.book Page 23 Thursday, June 30, 2005 8:21 PM
Control Panel
Control Panel
This illustration shows the control panel of a machine with options fully installed.
1
AAE036S
1. Screen contrast knob
Adjusts display panel brightness.
2. {User Tools/Counter}} key
• User Tools
Press to change defaults and conditions to meet your requirements. See
p.54 “Accessing User Tools (System
Settings)”.
• Counter
Press to check or print the counter value. See p.151 “Counter”.
3. Indicators
Display the status of the machine or indicate errors.
• d: Add Staple indicator. See p.131
“d Adding Staples”.
• D: Add Toner indicator. See p.117
“DAdding Toner”.
• B: Load Paper indicator. See p.114
“BLoading Paper”.
• L: Service Call indicator
• M: Open Cover indicator
• x: Misfeed indicator. See p.121
“xClearing Misfeeds”.
• Communicating: Communicating indicator. See “Control Panel”, Facsimile
Reference <Basic Features>.
• i: Confidential File indicator. See
“Control Panel”, Facsimile Reference
<Basic Features>.
• Receive File: Receiving File indicator.
See “Control Panel”, Facsimile Reference <Basic Features>.
4. {Adjust/Program Color}} key (copier
mode)
Use this key to adjust and register colors.
See “Color Adjustment”, “User Color”,
Copy Reference.
Note
❒ When image quality is adjusted, the
lamp in the {Adjust/Program Color}
} key
is lit.
5. Color circle
Refer to this when adjusting colors. See
“Color Adjustment”, Copy Reference.
6. Display panel
Displays operation status, error messages, and function menus. See p.25 “Display Panel”.
7. {Check Modes}} key
Press to check the entered copy job settings.
8. { Program}} key (copier/facsimile/scanner mode)
Press to register frequently used settings,
or recall registered settings.
23
ThemisC1_EN_zentai_pre_FM.book Page 24 Thursday, June 30, 2005 8:21 PM
Getting Started
9. {Clear Modes}} key
18. Number keys
Press to clear previous copy job settings.
Press to enter the number of copies, fax
numbers and data for a selected function.
10. {Energy Saver}} key
Press to switch into and out of Energy
Saver mode. See p.29 “Energy Saver
Mode”.
1
11. {Interrupt}} key (copier/scanner
mode)
Press to make interrupt copies during
copying or scanning. See “Interrupt
Copy”, Copy Reference.
12. Main power indicator and On
indicator
The main power indicator turns on when
you turn on the main power. The On indicator lights when the power is on.
Important
❒ Do not turn off the main power
switch while the On indicator is lit
or blinking. Doing so may damage
the hard disk.
13. Operation switch
Press to turn the power on (the On indicator goes on). To turn the power off,
press again (the On indicator goes off).
See p.27 “Turning On the Power”.
14. {Sample Copy}} key
Press to make a single set of copies or
prints to check print quality before making multiple sets. See “Sample Copy”
Copy Reference.
15. {Start}} key
Press to start copying. Press to start scanning or printing documents stored using
the Document Server function.
16. {Clear/Stop}} key
• Clear
Press to delete a number entered.
• Stop
Press to stop a job in progress.
17. {#}} key
Press to enter after a numerical value.
24
19. {Start Manual RX}} key, {On Hook Dial}
} key, { Pause/Redial}
} key, and
{Tone}
} key
Reference
Facsimile Reference <Basic Features>
and Facsimile Reference <Advanced
Features>
20. Color Selection keys (copy
mode)
Switch keys depending on the type of
original, or the copying purpose:
{Auto Color Selection}
}:
{Full Color}
}:
{Black & White}
}:
{Single Color}
}:
{Two-color}
}:
See “Color Functions”, Copy Reference.
21. Function keys
Press to select one of the following functions:
• Copy
• Document Server
• Facsimile
• Printer
• Scanner
22. Function status indicators.
Display the status of the above functions:
• Yellow: the function is selected.
• Green: active.
• Red: interrupted.
23. mindicator
The data indicator shows the status of
data reception. See “Control Panel”,
Printer Reference.
ThemisC1_EN_zentai_pre_FM.book Page 25 Thursday, June 30, 2005 8:21 PM
Control Panel
Display Panel
The display panel shows machine status, error messages, and function menus.
The function items displayed serve as selector keys You can select or specify an
item by lightly pressing them.
When you select or specify an item on the display panel, it is highlighted thus
. Keys appearing as
cannot be used.
1
Important
❒ A force or impact of more than 30 N (about 3 kgf) will damage the display
panel.
The copying screen is displayed as default after power on.
The following display shows a machine with options fully installed.
When the Authentication Screen is displayed
When Basic Authentication, Windows Authentication, or LDAP Authentication
is set, the authentication screen is displayed. Unless a valid user name and password are entered, operations are not possible with the machine.
Note
❒ Consult the User Administrator about your login user name and login password. For details of the various types of user authentication, consult the respective administrators.
❒ When User Code Authentication is set, the screen for entering a user code is
displayed instead. For details, see p.74 “Authentication Information”.
A Press [Enter] for Login User Name.
B Enter a login user name, and then press [OK].
C Press [Enter] for Login Password.
25
ThemisC1_EN_zentai_pre_FM.book Page 26 Thursday, June 30, 2005 8:21 PM
Getting Started
D Enter a login password, and then press [OK].
E Press [Login].
When the user is authenticated, the screen for the function you are using appears.
1
Note
❒ When the entered login user name or login password is not correct, "Authentication has failed." appears. Check the login user name and password.
Log Off
Important
❒ To prevent unauthorized users from using the machine, always log off when
you have finished using the machine.
A Press {User Tools / Counter}}.
B Press [Logout].
C Press [Yes].
D Press {User Tools / Counter}}.
26
ThemisC1_EN_zentai_pre_FM.book Page 27 Thursday, June 30, 2005 8:21 PM
Turning On the Power
Turning On the Power
This machine has two power switches.
The main power indicator turns on.
1
❖ Operation switch (right side of the
control panel)
Press to activate the machine.
When the machine has finished
warming up, you can make copies.
❖ Main power switch (left side of the machine)
Turning off this switch will turn
off the main power indicator on
the right side of the control panel.
After this is done, machine power
is completely off.
When the fax unit (optional) is installed, fax files in memory may be
lost if you turn this switch off. Use
this switch only when necessary.
Note
❒ This machine automatically enters
Energy Saver mode or turns itself
off if you do not use it for a while.
See p.61 “Auto Off Timer”, “Energy Saver Timer”.
AFT045S
Important
❒ Do not turn off the main power
switch immediately after turning it on. Doing so may result in
damage to the hard disk or
memory, leading to malfunction.
Turning On the Power
A Press the operation switch.
The On indicator turns on.
Turning On the Main Power
A Make sure that the power cord is
firmly plugged into the wall outlet.
B Open the switch cover, and then
turn on the main power switch.
ZFLS020N
Note
❒ If the power does not turn on
when the operation switch is
pressed, check the main power
switch is on. If it is off, turn it on.
27
ThemisC1_EN_zentai_pre_FM.book Page 28 Thursday, June 30, 2005 8:21 PM
Getting Started
B Open the switch cover, and then
Turning Off the Power
A Make sure the ADF is in the right
1
position.
B Press the operation switch.
-When the fax unit (optional) is
installed
The On indicator turns off.
ZFLS020N
Note
❒ Even if you press the operation
switch, and the indicator does
not turn off, it will blink in the
following cases:
• When the ADF is open.
• During communication with
external equipment.
• When the hard disk is active.
Turning Off the Main Power
Important
❒ Do not turn off the main power
switch when the On indicator is lit
or blinking. Doing so may result in
damage to the hard disk or memory.
❒ Be sure to turn off the main power
switch before pulling out the power plug. Not doing this may result
in damage to the hard disk or
memory.
A Make sure the On indicator is not
lit.
28
turn off the main power switch.
The main power indicator turns
off.
When the main power switch is
turned off while using the facsimile
function, waiting fax and print jobs
may be canceled, and incoming fax
documents not received. If you have
to turn off this switch for some reason, follow the procedure below.
Important
❒ Make sure 100% is shown as available memory on the display before
turning off the main power switch
or unplugging the power cord. Fax
files in memory are deleted an
hour after you turn off the main
power switch or unplug the power
cord. See "Turning off the Main
power", "When a Power Failure
Occurs", Facsimile Reference <Advanced Features>.
❒ The On indicator will not turn off,
but will blink in dial-in mode even
if you press the operation switch.
When this happens, check the explanations below, and turn off the
main power switch.
• The computer is not controlling
the machine.
• The machine is not receiving a
fax.
ThemisC1_EN_zentai_pre_FM.book Page 29 Thursday, June 30, 2005 8:21 PM
Turning On the Power
Saving Energy
- Energy Saver Mode
If you do not use the machine for a
certain period after an operation, or
when you press the { Energy Saver}
}
key, the display disappears and the
machine goes into Energy Saver
mode. When you press the {Energy
Saver}
} key again, the machine returns
to the ready condition. The machine
uses less electricity in Energy Saver
mode.
Note
❒ You can change the amount of time
the machine waits before switching to Energy Saver mode after
copying has finished or the last operation is performed. See p.61 “Energy Saver Timer”.
-Auto Off
The machine automatically turns itself off when the job is finished, after
a certain period of time has elapsed.
This function is called “Auto Off”.
1
Note
❒ You can change the Auto Off time.
See p.61 “Auto Off Timer”.
❒ The Auto Off Timer function will
not operate in the following cases:
• When a warning message appears
• When the service call message
appears
• When paper is jammed
• When the cover is open
• When the “Add Toner" message
appears
• When toner is being replenished
• When the User Tools/Counter
screen is displayed
• When fixed warm-up is in progress
• When the facsimile, printer or
other functions are active
• When operations were suspended during printing
• When the handset is in use
• When the On-hook dialing function is in use
• When a recipient is being registered in the address list or
group dial list
• When the Data In indicator is on
or blinking
• When the sample print or locked
print screen is displayed
29
ThemisC1_EN_zentai_pre_FM.book Page 30 Thursday, June 30, 2005 8:21 PM
Getting Started
1
30
ThemisC1_EN_zentai_pre_FM.book Page 31 Thursday, June 30, 2005 8:21 PM
2. Combined Function
Operations
Changing Modes
Note
❒ You cannot switch modes in any of the following situations:
• When scanning in a fax message for transmission
• During immediate transmission
• When accessing User Tools
• During interrupt copying
• During On hook dialing for fax transmission
• While scanning an original
31
ThemisC1_EN_zentai_pre_FM.book Page 32 Thursday, June 30, 2005 8:21 PM
Combined Function Operations
❒ The copying screen is displayed as default after power on. You can change
this default setting. See p.55 “Function Priority”.
2
AFT041S
- System Reset
The machine returns automatically to its initial condition when the job is finished, after a certain period of time has elapsed. This function is called “System
Reset”. See p.55 “Function Priority”.
Note
❒ You can change the System Reset time. See p.61 “System Auto Reset Timer”.
32
ThemisC1_EN_zentai_pre_FM.book Page 33 Thursday, June 30, 2005 8:21 PM
Multi-Access
Multi-Access
You can carry out another job using a different function while the current job is
being performed. Performing multiple functions simultaneously in this manner
is called “Multi-accessing”.
This allows you to handle jobs efficiently, regardless of how the machine is being
used. For example:
• While making copies, you can scan documents to store in the Document Server.
• While printing documents stored in the Document Server, the machine can
receive print data.
• You can make copies while receiving fax data.
• While printing print data, you can make operations for copying.
2
Note
❒ See p.55 “Print Priority” for setting function priority. As default, [Display
Mode] is set to first priority.
❒ When the internal tray 2, shift sort tray, 500-Sheet finisher or 1000-Sheet finisher is installed on the machine, you can specify the output tray where documents are delivered. For details about how to specify the output tray for
each function, see the following descriptions:
• p.56 “Output: Copier (copier)”
• p.57 “Output: Document Server (Document Server)”
• p.57 “Output: Facsimile (facsimile)”
• p.57 “Output: Printer (printer)”
- Function Compatibility
The chart shows Function Compatibility when print priority is set to “Interleave”. See p.55 “Print Priority”.
|: Simultaneous operations are possible.
$: Operation is enabled when the relevant function key is pressed and remote
switching (of the scanner/external extension) is done.
❍: Operation is enabled when the {Interrupt}
} key is pressed to interrupt the preceding operation.
→: Operation is performed automatically once the preceding operation ends.
×: The operation must be started once the preceding operation ends. (Simultaneous operations are not possible.)
33
ThemisC1_EN_zentai_pre_FM.book Page 34 Thursday, June 30, 2005 8:21 PM
*5
Printing from Document Server
Printing from Document Server
DeskTopBinder
Document Server
Scanning a Document to Store in Document Server
Operations for Document Server
Scanner
Scanning
Operations for Scanning
Print
Stapling
Printing
Data Reception
Printing Received Data
Memory Reception
Immediate Transmission
Reception
Transmission
Memory Transmission
*2
*2
*2
*2 *4 *4
*4
| → → ❍ ❍ $$| $| | | | | $$$$| | | |
*2
*2
*2
*2
❍❍ ❍ × × × × | × | | | | | × × × × × | | |
❍ ❍ ❍ × × × × | × | →| →→× × × × × →| →
× | | | | | $$$$$| | |
Transmission Opera- $ $ $ ❍ ❍ × × |
tion/Manual Reception Operation
Scanning an origi- × × × × × × × |
nal for Memory
Transmission
Memory Transmis- | | | | | | | |
sion
*3
Transmission
Facsimile
Operations for
Copying
Copying
Scanning an Original for Memory Transmission
| → → ❍ ❍ $$| $| | | | → $$$$| | | |
*1 *1 *1
Interrupt Copying
Printer
× × × ❍ ❍ $$| $| | | | | $$$$$| | |
*1 *1 *1
Sort
Copying
Sort
Operations for Copying
Stapling
Mode before you select
Copy
Operations for
Copying
Stapling
Operations for Copying
2
Transmission Operation/Manual Reception Operation
Facsimile
Interrupt Copying
Mode after you select Copy
Sending a Facsimile from Document Server Professional/Lite
Printing
Web Document Server
Combined Function Operations
× | | | | | × × × × × | | |
| | | | | | | | | | | | →|
*3 *3 *7
Immediate Trans- × × × × × × × | × | | | | | × × × × × | → |
mission
*3
*3
Reception
Memory Reception | | | | | | | | | | | | | | | | | | | | | |
Printer
*3 *3 *3 *7
Printing Received | | | | | | | | | | × | | | | | | | | | | |
Data
*7
*7
Data Reception
Print
Printing
Scanner
34
Stapling
| | | | | | | | | | | →→→| | | | | | | |
| | | ❍ ❍ | | | | | | | →→| | | | | | | |
| →| ❍ ❍ | | | | | | | →→| | | | | | | |
*5
Operations for
scanning
Scanning
*4 *4
*4
$$$❍ ❍ $$| $| | | | | × × $$$| | |
× × × × × × × | × | | | | | × × × × | | | |
ThemisC1_EN_zentai_pre_FM.book Page 35 Thursday, June 30, 2005 8:21 PM
DeskTopBinder
Printing from Document Server
Mode before you select
Document Server Operations for
$$$❍ ❍ $$| $| | | | | $$× ×
Document Server
Scanning a Docu- $ × × ❍ ❍ $ × | × | | | | | $ × × ×
ment to Store in
Document Server
Printing from Doc- $ | | ❍ ❍ | | | | | | | | | | | | |
ument Server
*4
*4
*6 *6
Printing from Document Server
Scanning a Document to Store in Document Server
Operations for Document Server
Scanner
Scanning
Operations for Scanning
Stapling
Printing
Data Reception
Print
Reception
Printing Received Data
Memory Reception
Immediate Transmission
Document Server
Printer
Transmission
Memory Transmission
Scanning an Original for Memory Transmission
Copying
Sort
Operations for Copying
Stapling
Operations for Copying
Transmission Operation/Manual Reception Operation
Facsimile
Interrupt Copying
Mode after you select Copy
Sending a Facsimile from Document Server Professional/Lite
Printing
Web Document Server
Multi-Access
2
× | | |
× | | |
| | | |
*6
DeskTopBinder Printing from Doc- | | | ❍ ❍ | | | | | | | | | | | | | | × | |
Professional/Lite ument Server
*4
Web Document
Server
*1
*2
*3
*4
*5
*6
*7
Sending a Facsimi- | | | | | | | | | | | | | | | | | | | | × |
le from Document
Server
Printing
| | | | | | | | | | | | | | | | | | | | | ×
*4
Simultaneous operations are only possible after the preceding job documents are all
scanned and the [NextJob] key appears.
You can scan a document after the preceding job documents are all scanned.
Operation is possible when extra lines are added.
During stapling, printing automatically starts after the current job.
Stapling is not available.
Simultaneous operation become possible after you press the [NextJob] key.
During parallel reception, any subsequent job is suspended until the receptions are
completed.
Limitation
❒ Stapling cannot be used at the same time for multiple functions.
❒ A machine with the 500-Sheet Finisher installed cannot accept other jobs
while printing with the stapling operation.
35
ThemisC1_EN_zentai_pre_FM.book Page 36 Thursday, June 30, 2005 8:21 PM
Combined Function Operations
❒ A machine with the 1000-Sheet Finisher installed, that is printing with the stapling operation on paper larger than A4 size starts the subsequent job (for
which Internal Shift Tray is specified as the output tray) only after the current
print job finishes.
❒ While printing is in progress, scanning a document using another function
may take more time.
2
36
ThemisC1_EN_zentai_pre_FM.book Page 37 Thursday, June 30, 2005 8:21 PM
3. Document Server
Relationship between Document Server
and Other Functions
The following table describes the relationship between the Document Server
and other functions.
function
Where to store
documents
Displaying a list
Printing stored
documents
Sending documents
Copy
Copy/Document
Server
Available
Available
Not Available
Printer
Document Server Available
Available
Not Available
Facsimile
Facsimile
Available
Available
Available *1
Scanner
Scanner
Not Available *2
Not Available
Available *3
*1
*2
*3
You can send stored documents using the facsimile function. See “Sending a Stored
File”, Facsimile Reference <Advanced Features>.
You can display stored documents using the scanner function. See “Displaying the
List of Stored Files”, Scanner Reference.
You can send stored documents using the scanner function. See “Sending Stored
Files by E-mail or Scan to Folder, or Delivering”, Scanner Reference.
Note
❒ The following table shows the capacity of the Document Server.
Number of pages for
each file
Number of files
Number of pages in
total
1,000 pages
1,000 files
2,000 pages
Copy
Printer
Scanner
Facsimile
37
ThemisC1_EN_zentai_pre_FM.book Page 38 Thursday, June 30, 2005 8:21 PM
Document Server
Document Server Display
❖ Document Server Main Display
3
AFT042S
1. Operating status and messages.
2. The title of the currently selected
4. The operation keys
5. The functions under which the
screen.
documents were stored.
3. The numbers of originals, copies,
and printed pages.
The icons below show the functions active when the documents were stored
in the Document Server.
Function
Copier
Facsimile
Printer
Icon
Note
❒ Depending on the settings of security functions, not all the stored documents may be displayed.
38
ThemisC1_EN_zentai_pre_FM.book Page 39 Thursday, June 30, 2005 8:21 PM
Using the Document Server
Using the Document Server
Storing Data
❖ File name
Stored documents are automatically
named “COPY0001”, “COPY0002”.
You ca n c han ge a ss i gn ed fi l e
names.
❖ User name
You can register a user name to
identify the user or user group that
stored the documents. To assign it,
you can register the user name using the name assigned to the user
code, or by entering the name directly.
Reference
For details about the user name,
see p.72 “Registering Names”.
❖ Password
You can set a password for stored
documents, and use it to prevent
others printing them. When a password is set for the documents,
appears next to the documents.
Reference
To store documents without using
Document Server function, see the
manuals for those modes.
Important
❒ Data stored in the machine might
be lost if some kind of failure occurs. The manufacture shall not be
responsible for any damage resulting from loss of data.
❒ Be careful not to let anyone know
your password, especially when
entering a password or recording
it. Keep any record of your password in a secure place.
❒ Avoid using a single number or
consecutive numbers for a password such as “0000” or “1234”,
since the numbers like this are easy
to guess, so using them will not
provide a worthwhile level of security.
❒ A document accessed with a correct password remains selected
even after operations are complete,
and it can be accessed by other users. To stop this, be sure to press
the {Clear Modes}
} key to cancel the
document selection.
❒ The user name used when adding
a document to the Document Server is to identify the document creator and type. It is not to protect
confidential documents from others.
3
Note
❒ Enter a four-to eight-digit password.
❒ By default, data stored in the Document Server is deleted after three
days (72 hours). You can specify
the time taken for the stored data
to be deleted automatically. See
p.68 “Auto Delete File”.
❒ If you do not want stored data to
be automatically deleted, select
[No] in Auto Delete File before storing a document. If you select [Yes]
later, data stored afterward will be
automatically deleted.
❒ When the machine is printing a
document stored using the copier
function, wait until printing has
finished before you store a document in the Document Server.
39
ThemisC1_EN_zentai_pre_FM.book Page 40 Thursday, June 30, 2005 8:21 PM
Document Server
A Press the {Document Server}} key.
E Make any required settings.
Reference
For details, see Copy Reference.
3
ZGJS776N
B Press [Scan Original].
C Enter a user name, file name, or
password if necessary.
Note
❒ If you do not enter a file name,
one is automatically assigned.
Reference
p.40 “To register or change a
user name”
p.41 “To change a file name”
p.42 “To set or change a password”
D Place originals either on the exposure glass or in the ADF.
Reference
For information about types of
originals and how to place
them, see “Placing Originals”
Copy Reference.
40
F Press the {Start}} key.
The document is stored in the Document Server.
Note
❒ To stop scanning, press the
{ Clear/Stop}
} key. To restart a
paused scanning job, press [Continue] in the confirmation display. To delete saved images
and cancel the job, press the
[Stop] key.
❒ When a password is set, appears on the left side of the file
name.
❒ If you placed originals on the
exposure glass, press [Scanning
Finished] after all the originals
have been scanned. The Select
Files to Print display appears.
To register or change a user name
A Press [Scan Original].
The Scan Original display appears.
B Press [User Name].
If user names are already registered,
the Change User Name display appears. To use an unregistered user
name, press [Non-programmed Name].
ThemisC1_EN_zentai_pre_FM.book Page 41 Thursday, June 30, 2005 8:21 PM
Using the Document Server
When no user names are registered
in the Address Book, the User
(Destination) Name entry display
appears.
Reference
p.74 “Authentication Information”
When no user names are
registered in the Address Book
A Enter a new user name, and then
press [OK].
When using a registered user
name in the Address Book
A Select a registered user name
from the list, and then press
[OK].
3
Reference
p.153 “Entering Text”
To change a file name
A Press [Scan Original].
The Scan Original display appears.
To change your user name to an
unregistered user name, proceed to the next step.
B Press [File Name].
Reference
p.74 “Registering a New
User Code”
When using an unregistered user
name in the Address Book
A To enter an unregistered user
name, press [Non-programmed
Name].
B Enter a new user name, and then
press [OK].
Reference
p.153 “Entering Text”
The Change File Name display appears.
C Press [Delete All] to delete the old
file name.
Note
❒ You can also use [Backspace] to
delete unnecessary characters.
D Enter a new file name, and then
press [OK].
Note
❒ Up to 20 characters can be entered as a file name. Note that
only 16 characters of each file
name appear in the document
list.
Reference
p.153 “Entering Text”
41
ThemisC1_EN_zentai_pre_FM.book Page 42 Thursday, June 30, 2005 8:21 PM
Document Server
To set or change a password
C Press [File Management].
A Press [Scan Original].
The Scan Original display appears.
B Press [Password].
D Press [Change User Name], [Change
File Name], or [Change Password].
E Enter the new user name, file name,
3
C Enter
a four-to eight-digit password using the number keys, and
then press the {#}
} key.
or password using the letter keys
or number keys and then press
[OK].
D Reenter
Reference
p.40 “To register or change a
user name”
E Press [OK].
p.41 “To change a file name”
p.42 “To set or change a password”
the password (four-to
eight-digit) for verification, and
then press the {#}
} key.
Changing a Stored
Document's File Name, User
Name, or Password
A Press the {Document Server}} key.
B Select the document with the user
F Press [OK].
Selecting a Document
A Press the {Document Server}} key.
B Select a document you want to print.
name, file name, or password you
want to change.
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
42
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
❒ You can search for the document using [Search by User Name]
or [Search by File Name] at the left
top of the display. See p.43
“Searching for Stored Documents”.
ThemisC1_EN_zentai_pre_FM.book Page 43 Thursday, June 30, 2005 8:21 PM
Using the Document Server
❒ You can sort document names
in the list by user name, file
name, or date. To sort documents, press [User Name], [File
Name], or [Date].
❒ If you cannot determine docum ent c on ten t from t he file
name, you can print just the first
page of the document for checking purposes. See p.46 “Printing
the first page”.
❒ To cancel document selection,
press it again.
C To print multiple documents, repeat step B in the order you want
to print.
Note
❒ You can select up to 30 documents.
❒ If the sizes or resolution of selected documents are not the
same, it may not be possible to
print them.
❒ If you want to change the printing order, cancel the selection,
and select documents again,
this time in the order you want.
❒ If you press the {Clear Modes}
}
key, selection of all documents
will be canceled.
❒ If you press [Printg Odr], the documents in print order.
To check the details of stored documents
A Select a document to display its
detailed information.
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
B Press [Detail].
3
Detailed information about the
document appears.
Note
❒ If you selected several documents, use [U
U] and [T
T] to view
the details of each.
❒ Press [OK]. The Select Files to
Print display reappears.
Searching for Stored
Documents
You can use either [Search by File
Name] or [Search by User Name] to
search for documents stored in the
Document Server. You can also list
stored documents in a preferred order.
Note
❒ If you install DeskTopBinder Professional or DeskTopBinder Lite
on your computer, you can search
for and rearrange documents using your computer.
Reference
Manuals for DeskTopBinder Professional/Lite or Help
43
ThemisC1_EN_zentai_pre_FM.book Page 44 Thursday, June 30, 2005 8:21 PM
Document Server
To search by file name
A Press the {Document Server}} key.
B Press [Search by File Name].
3
C Enter the file name using the letter keys, and then press [OK].
Only files beginning with the
name entered appear in the Select
Files to Print display.
Reference
p.153 “Entering Text”.
Note
❒ To display all files stored in the
Document Server, press [File
List].
To search by user name
A Press the {Document Server}} key.
B Press [Search by User Name].
D To
specify an unregistered user
name, press [Non-programmed
Name]. Enter a user name, and
then press [OK].
Reference
p.153 “Entering Text”
E Press [OK].
Only files beginning with the
name entered appear in the Select
Files to Print display.
Note
❒ To display all files stored in the
Document Server, press [File
List].
Printing Stored Documents
Note
❒ You can print stored documents
from a network computer using a
Web browser. For details about
how to start the Web browser, see
“Using Web Image Monitor”, Network Guide.
A Select a document you want to
print.
C To specify a registered user name,
select the user name from the displayed list, and then press [OK].
Note
❒ To specify an unregistered user
name, follow the procedure below.
44
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
❒ You can print multiple documents. See p.42 “Selecting a
Document”.
ThemisC1_EN_zentai_pre_FM.book Page 45 Thursday, June 30, 2005 8:21 PM
Using the Document Server
B If you need to change print settings, press [Print Settings].
The Print Settings display appears.
User names, file names, and print
order of documents appear.
Note
❒ Print settings made for printing
in copier or printer function remain after printing and applied
to the next job. Print settings
made in facsimile mode, however, do not remain.
❒ If you select multiple documents,
the print settings will remain
applied to the first document,
but not to other documents.
❒ Print setting items are listed below. For details about print results of each setting, see Copy
Reference.
❖ Binding format
• 2 Sided Copy Top to Top
• 2 Sided Copy Top to Bottom
• Magazine
• Booklet
❖ Cover handling
• Cover/Slip Sheet
• Edit/Stamp
❖ Finish
• Sort
• Rotate Sort
• Stack
• Staple
❒ If you print more than one set
using the Sort function, you can
check the print result by printing out only the first set. See
p.46 “Sample copy”.
❒ When multiple documents are
printed at the same time, you
can combine them into a single
set by adjusting the print order.
❒ When multiple documents are
printed at the same time, print
settings made for the document
printed first are applied to all
other documents.
❒ If you select multiple files, you
can check file names or print order selected in step A by scrolling the list using [T
T] and [U
U].
❒ Press [Select File] to return to the
Select Files to Print display.
❒ The preset stamp function is not
available for documents stored
in facsimile mode.
3
C Enter the required number of prints
using the number keys
Note
❒ Up to 100 can be entered.
D Press the {Start}} key.
Printing starts.
To stop printing
A Press the {Clear/Stop}} key.
B Press [Stop].
45
ThemisC1_EN_zentai_pre_FM.book Page 46 Thursday, June 30, 2005 8:21 PM
Document Server
Changing the number of copies
during printing
Limitation
❒ The number of copies can only be
changed when the Sort function is
selected in the print settings.
A Press the {Clear/Stop}} key.
B Press [Change Quantity].
C Enter a new number of copies us-
3
ing the number key.
D Press the {#}} key.
E Press [Continue].
Printing restarts.
Sample copy
If you print multiple sets using the
Sort function, you can check the print
order or print settings are correct by
printing only the first set using the
{Sample Copy}
} key.
Limitation
❒ This function can only be used
when the Sort function is selected.
A Select the document.
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
46
❒ You can search for the document by using [Search by User
Name] or [Search by File Name] at
the left top of the display. See
p.43 “Searching for Stored Documents”.
❒ You can sort document names
in the list by user name, file
name, or date. To sort documents, press [User Name], [File
Name], or [Date].
❒ To cancel a document selection,
press it again.
B Press the {Sample Copy}} key.
The first set prints out.
C If the sample is acceptable, press
[Print].
Note
❒ Press [Suspend] to cancel printing and return to the Print Settings menu to change settings.
Printing the first page
You can print the first page of the document selected in the Select Files to
Print display to check its content.
If more than one document selected,
the first page of each is printed.
A Select the document.
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
❒ You can search for the document by using [Search by User
Name] or [Search by File Name] at
the left top of the display. See
p.43 “Searching for Stored Documents”.
ThemisC1_EN_zentai_pre_FM.book Page 47 Thursday, June 30, 2005 8:21 PM
Using the Document Server
❒ You can sort document names
in the list by user name, file
name, or date. To sort documents, press [User Name], [File
Name], or [Date].
❒ To cancel a document selection,
press it again.
B Press [Print 1st Page].
C Press the {Start}} key.
Deleting Stored Documents
Important
❒ You can store up to 1,000 documents in the Document Server. No
more documents can be stored
when the total is 1,000. You should
delete unnecessary documents to
increase available memory.
Note
❒ You can delete all stored documents at once with User Tools. See
p.68 “Delete All Files”.
❒ You can delete stored documents
from a network computer using
the Web browser. For details about
how to start the Web browser, see
“Using Web Image Monitor”, Network Guide.
A Press the {Document Server}} key.
B Select the document to delete.
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
❒ You can delete multiple documents at once. See p.42 “Selecting a Document”.
❒ You can search for a document
by using [Search by User Name] or
[Search by File Name] at the left
top of the display. See p.43
“Searching for Stored Documents”.
❒ You can sort document names
in the list by the user name, file
name, or date. To sort documents, press [User Name], [File
Name], or [Date].
❒ If you cannot find the document
by name, you can print the first
page of a document to check its
contents. See p.46 “Printing the
first page”.
❒ Press the selected line again to
cancel the print job.
3
C Press [Delete File].
D Press [Delete] to delete the document.
Viewing Stored Documents
Using a Web Browser
Reference
The Web browser's Help
A Start a Web browser.
B Enter “http:// (IP address of this
machine) /” in the [Address] box.
The top page appears on the Web
browser.
47
ThemisC1_EN_zentai_pre_FM.book Page 48 Thursday, June 30, 2005 8:21 PM
Document Server
C Click [Document Server].
The [Document Server File List] appears.
Note
❒ To switch the display format,
click [Details], [Thumbnails] or
[Icons] from the [Display method]
list.
D Click the properties button of the
3
document you want to check.
Information about that document
appears.
E Check the document's content.
Note
❒ To enlarge the document preview, click [Enlarge Image].
Downloading Stored
Documents
Note
❒ File Format Converter is required
when downloading documents
stored in copier or printer mode.
A Start a Web browser.
B Enter “http:// (IP address of this
machine) /” in the [Address] box.
The top page appears on the Web
browser.
C Click [Document Server].
The [Document Server File List] appears.
Note
❒ To switch the display format,
click [Details], [Thumbnails] or
[Icons] from the [Display method]
list.
48
D Click the properties button of the
document you want to download.
E Select [PDF], [JPEG], or [Multi-page
TIFF] in the [File format] list.
Note
❒ [JPEG] can only be selected for
documents stored in scanner
mode.
❒ [Multi-page TIFF] is available when
file fo rm at converter is installed.
❒ [Multi-page TIFF] cannot be selected for documents stored in copier or printer mode.
F Click [Download].
G Click [OK].
ThemisC1_EN_zentai_pre_FM.book Page 49 Thursday, June 30, 2005 8:21 PM
Settings for the Document Server
Settings for the Document Server
❖ Copier/Document Server Features (See “General Features P.4/5”, Copy Reference.)
Items
General Features
Default
Document Server Storage Key: F1 2 Sided Original Top to Top
Document Server Storage Key: F2 1 Sided→1 Sided Combine
Document Server Storage Key: F3 1 Sided→1 Sided Combine: 4
originals
3
Document Server Storage Key: F4 1 Sided→1 Sided Combine: 8
originals
Document Server Storage Key: F5 Create Margin
❖ System Settings (See p.55 “General Features”, p.58 “Tray Paper Settings”, p.61
“Timer Settings”, and p.63 “Administrator Tools”.)
Items
General Features
Tray Paper Settings
Timer Settings
Administrator Tools
Default
Warm Up Notice
On
Copy Count Display
Up
Output: Document Server
Internal Tray 1
Paper Tray Priority: Copier
Tray 1
Cover Sheet Tray
Off
Slip Sheet Tray
Off
Copier/Document Server
Auto Reset Timer
60 seconds
Auto Delete File
Yes After 3 day(s)
Delete All Files
--
49
ThemisC1_EN_zentai_pre_FM.book Page 50 Thursday, June 30, 2005 8:21 PM
Document Server
3
50
ThemisC1_EN_zentai_pre_FM.book Page 51 Thursday, June 30, 2005 8:21 PM
4. User Tools (System Settings)
User Tools Menu (System Settings)
Reference
For details about Interface Settings and File Transfer, see “User Tools Menu
(System Settings)”, Network Guide.
For details about parallel interface, see “System Settings (Parallel Connection)”, Printer Reference.
To register addresses and users, specify them under [Address Book Management].
For details, see p.69 “Registering Addresses and Users for Facsimile/Scanner
Functions”.
❖ General Features (See p.55 “General Features”.)
Default
Panel Tone
On
Warm Up Notice
On
Copy Count Display
Up
Function Priority
Copier
Print Priority
Display Mode
Function Reset Timer
3 seconds
Output: Copier
Internal Tray 1
Output: Document Server
Internal Tray 1
Output: Facsimile
Internal Tray 2
Output: Printer
Internal Tray 1
51
ThemisC1_EN_zentai_pre_FM.book Page 52 Thursday, June 30, 2005 8:21 PM
User Tools (System Settings)
❖ Tray Paper Settings (See p.58 “Tray Paper Settings”.)
Default
4
Paper Tray Priority: Copier
Tray 1
Paper Tray Priority: Facsimile
Tray 1
Paper Tray Priority: Printer
Tray 1
Tray Paper Size: Tray 1
Auto Detect
Tray Paper Size: Tray 2
Auto Detect
Tray Paper Size: Tray 3
Auto Detect
Tray Paper Size: Tray 4
Auto Detect
Paper Type: Bypass tray
No Display
Paper Type: Tray 1
No Display :2 Sided Copy : Auto Paper Select On
Paper Type: Tray 2
No Display :2 Sided Copy : Auto Paper Select On
Paper Type: Tray 3
No Display :2 Sided Copy : Auto Paper Select On
Paper Type: Tray 4
No Display :2 Sided Copy : Auto Paper Select On
Cover Sheet Tray
Off
Slip Sheet Tray
Off
Printer Bypass Paper Size
81/2" × 11"K
❖ Timer Settings (See p.61 “Timer Settings”.)
Default
Auto Off Timer
45 minute(s)
Energy Saver Timer
15 minute(s)
Panel Off Timer
60 seconds
System Auto Reset Timer
60 seconds
Copier/Document Server Auto Reset Timer
60 seconds
Facsimile Auto Reset Timer
30 seconds
Printer Auto Reset Timer
60 seconds
Scanner Auto Reset Timer
60 seconds
Set Date
--
Set Time
--
Auto Logout Timer
60 seconds
❖ Interface Settings
• For details about network settings, see “User Tools Menu (System Settings)”, Network Guide.
• For details about parallel interface, see “System Settings (Parallel Connection)”, Printer Reference.
52
ThemisC1_EN_zentai_pre_FM.book Page 53 Thursday, June 30, 2005 8:21 PM
User Tools Menu (System Settings)
❖ File Transfer
• For details about network settings, see “User Tools Menu (System Settings)”, Network Guide.
❖ Administrator Tools (See p.63 “Administrator Tools”.)
• For details about Address Book Management, Address Book: Program/Change/Delete Group, Address Book: Program/Change/Delete
Transfer Request, see p.69 “Registering Addresses and Users for Facsimile/Scanner Functions”.
Default
User Authentication Management
Off
Administrator Authentication Management
Off
Program /Change Administrator
--
Key Counter Management
--
Extended Security
--
Display/Print Counter
--
Display/Clear/Print Counter per User
--
Address Book Management
--
Address Book: Program/Change/Delete Group
--
Address Book: Program/Change/Delete Transfer Request
--
Address Book: Change Order
--
Print Address Book: Destination List
--
Address Book: Edit Title
--
Address Book: Select Title
Title 1
Auto Delete File
Yes After 3 day(s)
Delete All Files
--
Program/Change/Delete LDAP Server
--
Use LDAP Server
Off
AOF (Always ON)
On
Firmware Version
--
4
53
ThemisC1_EN_zentai_pre_FM.book Page 54 Thursday, June 30, 2005 8:21 PM
User Tools (System Settings)
Accessing User Tools (System Settings)
This section is for administrators in
charge of this machine.
User Tools allow you to change or set
defaults.
Note
❒ Operations for system settings differ from normal operations. Always quit User Tools when you
have finished. See p.54 “Exiting
User Tools”.
❒ Any changes you make with User
Tools remain in effect even if the
main power switch or operation
switch is turned off, or the {Energy
Saver}
} or { Clear Modes}
} key is
pressed.
4
C Select the menu, and then press
the appropriate key.
Reference
p.51 “User Tools Menu (System
Settings)”
D Change settings by following instructions on the display panel,
and then press [OK].
Note
❒ To cancel changes made to settings and return to the initial
display, press the {User
Tools/Counter}
} key.
Exiting User Tools
Changing Default Settings
A Press the {User Tools/Counter}} key.
Note
❒ If the Administrator Authentication is specified, contact your administrator.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
54
Note
❒ You can also exit User Tools by
pressing [Exit].
ThemisC1_EN_zentai_pre_FM.book Page 55 Thursday, June 30, 2005 8:21 PM
Settings You Can Change with User Tools
Settings You Can Change with User Tools
Reference
To access User Tools, see p.54 “Accessing User Tools (System Settings)”.
General Features
❖ Panel Tone
The beeper (key tone) sounds when a key is pressed.
Note
❒ Default: On
4
❖ Warm Up Notice (copier/Document Server)
You can set the beeper to sound when the machine becomes ready to copy after switching out of Energy Saver mode, or when the power is turned on.
Note
❒ If the Panel Tone setting is “OFF”, the beeper does not sound, regardless
of the Warm Up Notice setting.
❒ Default: On
❖ Copy Count Display (copier/Document Server)
The copy counter can be set to show the number of copies made (count up) or
the number of copies yet to be made (count down).
Note
❒ Default: Up (count up)
❖ Function Priority
You can specify the mode to be displayed immediately after the operation
switch is turned on, or when System Reset mode is turned on.
Note
❒ Default: Copier
❖ Print Priority
Print Priority is given to the mode selected.
Reference
p.33 “Multi-Access”
Note
❒ Default: Display Mode
❒ When [Interleave] is selected, the current print job will be interrupted after
a maximum of five sheets.
55
ThemisC1_EN_zentai_pre_FM.book Page 56 Thursday, June 30, 2005 8:21 PM
User Tools (System Settings)
❒ When the internal tray 2, shift sort tray, 500-Sheet finisher or 1000-Sheet
finisher is installed on the machine, you can specify an output tray for each
document to be delivered. For details about how to specify an output tray
for each function, see the following sections:
• p.56 “Output: Copier (copier)”
• p.57 “Output: Document Server (Document Server)”
• p.57 “Output: Facsimile (facsimile)”
• p.57 “Output: Printer (printer)”
❖ Function Reset Timer
You can set the length of time the machine waits before changing modes
when using the multi-access function (see p.33 “Multi-Access”). This is useful
if you are making many copies and have to change settings for each copy. If
you set a longer reset period, you can prevent interruption from other functions.
4
Note
❒ Default: 3 seconds
❒ The Function Reset Timer setting is ignored if [Interleave] is set for Print Priority (see p.55 “Print Priority”).
❒ When you select [Set Time], enter the time (3–30 seconds, in 1 second increments) using the number keys
❖ Output: Copier (copier)
You can specify a tray to which documents are delivered.
AFT003S
Note
❒ Default: Internal Tray 1
56
ThemisC1_EN_zentai_pre_FM.book Page 57 Thursday, June 30, 2005 8:21 PM
Settings You Can Change with User Tools
❖ Output: Document Server (Document Server)
You can specify the tray to which documents are delivered.
Note
❒ Default: Internal Tray 1
❒ For details about output trays, see p.56 “Output: Copier (copier)”.
❖ Output: Facsimile (facsimile)
You can specify the tray to which documents are delivered.
Note
❒ Default: Internal Tray 2
❒ For details about output trays, see p.56 “Output: Copier (copier)”.
❖ Output: Printer (printer)
You can specify the tray to which documents are delivered.
4
Note
❒ Default: Internal Tray 1
❒ The output trays set on the printer driver have priority over the output tray
specified above.
Output tray settings
Limitation
❒ You cannot interrupt the current stapling job even if a stapling job is specified
by a different function.
❒ When the 500-Sheet Finisher or 1000-Sheet finisher is installed and stapling or
shift-sorting is specified for a job, the job will be delivered to the finisher shift
tray regardless of the output tray specified.
❒ The output tray used can be changed, when a stapling job of a different function is interrupted by copying, as in the following cases:
❖ When the 500-Sheet Finisher is installed and the finisher tray is specified for the
output tray:
• The interrupting job will be delivered to Internal Tray 1.
❖ When the 1000-Sheet Finisher is installed and the finisher tray is specified for the
output tray:
• The interrupting job will be delivered to Finisher Proof Tray.
57
ThemisC1_EN_zentai_pre_FM.book Page 58 Thursday, June 30, 2005 8:21 PM
User Tools (System Settings)
Tray Paper Settings
❖ Paper Tray Priority: Copier (copier/Document Server)
You can specify the tray to supply paper for output.
Note
❒ Default: Tray 1
❖ Paper Tray Priority: Facsimile (facsimile)
You can specify the tray to supply paper for output.
Note
❒ Default: Tray 1
4
❖ Paper Tray Priority: Printer (printer)
You can specify the tray to supply paper for output.
Note
❒ Default: Tray 1
❖ Tray Paper Size: (Tray 1-4)
Select the size of the paper loaded in the paper tray.
❖ The paper sizes you can set for trays are as follows:
• The paper sizes you can set for trays 1 and 2 are as follows:
• Auto Detect, A3L, B4 JISL, A4K, A4L, B5 JISK, B5 JISL, A5K,
A5L, A6L, 8KL, 16KK, 16KL
• 11"×17"L, 81/2"×14"L, 81/2"×13"L, 81/2"×11"K, 81/2"×11"L,
81/4"×13"L, 8"×13"L, 71/4"×101/2"K, 71/4"×101/2"L, 51/2"×81/2"K,
51/2"×81/ 2"L, custom size (100.0-297.0 mm (3.94"-11.69") wide ×
148.0-432.0 mm (5.83"-17.00") long)
• The paper sizes you can set for trays 3 and 4 are as follows:
• Auto Detect, A3L, B4 JISL, A4K, A4L, B5 JISK, B5 JISL, A5K,
A5L, 8KL, 16KK, 16KL
11"×17"L, 81/ 2 "×14"L, 81/ 2 "×13"L, 8 1/ 2"×11"K, 8 1/ 2"×11"L,
81/4"×13"L, 8"×13"L, 71/4"×101/2"L, 51/2"×81/2"K, 51/2"×81/2"L,
custom size (148.0-297.0 mm (5.83"-11.69") wide × 148.0-432.0 mm
(5.83"-17.00") long)
Important
❒ If the specified paper size differs from the actual size of the paper loaded
in the paper tray, a misfeed might occur because the correct paper size was
not detected.
58
Note
❒ The paper guide for the optional LCT is fixed for A4K, 81/2"×11"K size paper. Contact your service representative if you need to change the paper size.
❒ Default: Auto Detect
ThemisC1_EN_zentai_pre_FM.book Page 59 Thursday, June 30, 2005 8:21 PM
Settings You Can Change with User Tools
Reference
p.126 “Changing the Paper Size”
❖ Paper Type: Bypass tray
Sets the display so you can see what type of paper is loaded in the bypass tray.
❖ The paper types you can set for the bypass tray are as follows:
No Display, Recycled Paper, Special Paper, Color Paper, Letterhead, Preprinted Paper, Prepunched Paper, Bond Paper, Cardstock, Label Paper,
Thick Paper, OHP, Plain: Dup.Back, Thick: Dup.Back
Note
❒ Default: No Display
❖ Paper Type: Tray 1–4
Sets the display so you can see what type of paper is loaded in each paper
tray. The print function uses this information to automatically select the paper tray.
4
❖ The paper types you can set for trays are as follows:
• The paper types you can set for trays 1 and 2 are as follows:
• No Display, Recycled Paper, Special Paper, Color Paper, Letterhead,
Preprinted Paper, Prepunched Paper, Bond Paper, Cardstock, Label
Paper, Thick Paper, OHP
• The paper types you can set for trays 3 and 4 are as follows:
• No Display, Recycled Paper, Special Paper, Color Paper, Letterhead,
Preprinted Paper, Prepunched Paper, Bond Paper, Cardstock
Note
❒ Default:
• Paper Type: No Display
• Copying Method in Duplex: 2 Sided Copy
• Apply Auto Paper Select: Yes
❒ When paper of the same type and size is loaded in two different paper
trays and you want to specify tray for 2 Sided Copy and tray for 1 Sided
Copy, specify the upper tray for 2 Sided Copy. If one of the trays is specified as the default in Paper Tray Priority, assign 2 Sided Copy to that tray.
❒ A mark appears next to the paper tray if [No] is selected in Auto Paper
Select.
Limitation
❒ [Auto Paper Select] can only be selected for the copier function if [No Display]
and [Recycled Paper] are selected. If [No] is selected, Auto Paper Select is not
valid for the tray.
59
ThemisC1_EN_zentai_pre_FM.book Page 60 Thursday, June 30, 2005 8:21 PM
User Tools (System Settings)
❖ Cover Sheet Tray
Allows you to specify and display the paper tray that is setting cover sheets.
After selecting the paper tray, you can also specify the display timing and
copy method for two-sided copying.
Note
❒ Default:
• Tray to Program: Off
❒ Functions using the cover sheet tray setting are the front cover function
and front/back cover function.
❒ When [At Mode Selected] is selected, cover sheet tray settings only appear
when the cover function or slip sheet function is selected.
❒ When [Full Time] is selected, the cover sheet tray is always displayed.
❒ You can set Copying Method in Duplex only when [At Mode Selected] is selected.
4
Reference
“Covers”, Copy Reference
❖ Slip Sheet Tray
Allows you to specify and display the paper tray that will be inserting slip
sheets. After selecting the paper tray, you can also specify the display timing
and copy method.
Note
❒ Default:
• Tray to Program: Off
❒ When [At Mode Selected] is selected, slip sheet tray settings only appear
when the cover function or slip sheet function is selected.
Reference
“Slip Sheets”, Copy Reference
❖ Printer Bypass Paper Size
You can specify the size of the paper in the bypass tray when printing data
from the computer.
• The paper types you can set for trays are as follows:
A3L, A4K, A4L, A5K, A5L, A6L, B4 JISL, B5 JISK, B5 JISL, B6 JISL,
C5 EnvK, C6 EnvK, DL EnvK, 12" × 18"L, 11" × 17"L, 81/2" × 14"L,
8 1/ 2" × 13"L, 8 1/ 2" × 11"K, 8 1/ 2" × 11"L, 8 1/ 4" × 13"L, 8" × 13"L,
71/4" × 101/2"K, 71/4" × 101/2"L,51/2" × 81/2"K, 51/2" × 81/2"L, 41/8" × 91/2"K,
37/8" × 71/2"K, 8KL, 16KK, 16KL
Note
❒ Default:81/2" × 11"K
❒ You can specify a custom size of between 90.0 and 297.0 mm (3.55"-11.69")
vertically, and between 148.0 and 432.0 mm (5.83"-17.00") horizontally.
60
ThemisC1_EN_zentai_pre_FM.book Page 61 Thursday, June 30, 2005 8:21 PM
Settings You Can Change with User Tools
Timer Settings
❖ Auto Off Timer
After a specified time has elapsed following job completion, the machine automatically turns off in order to conserve energy. This function is called “Auto Off”.
The machine status after the Auto Off operation is referred to as “Sleep
mode”. For the Auto Off Timer, specify the time to elapse before Auto Off.
Note
❒ Default: 45 minute(s)
❒ Enter a time interval from 1 to 240 minutes, using the number keys
❒ Auto Off may not work when error messages appear.
4
❖ Energy Saver Timer
Set the amount of time the machine waits before switching to lower-power
mode after copying has finished or the last operation is performed.
The time can be set from 1 to 240 minutes using the number keys
Note
❒ Default: 15 minute(s)
❖ Panel Off Timer
Set the amount of time the machine waits before switching the panel off after
copying has finished or the last operation is performed.
Note
❒ The warm up time for making a copy from standby mode is 3 seconds for
Panel off Level 1 and 10 seconds for Panel off Level 2.
❒ Default: 60 seconds
❒ Enter a time interval from 10 to 999 seconds using the number keys
❖ System Auto Reset Timer
The System Reset setting automatically switches the screen to that of the function set in Function Priority, when no operations are in progress, or when an
interrupted job is cleared. This setting determines the system reset interval.
See p.55 “Function Priority”.
Note
❒ Default: On, 60 seconds
❒ The time can be set from 10 to 999 seconds, using the number keys
61
ThemisC1_EN_zentai_pre_FM.book Page 62 Thursday, June 30, 2005 8:21 PM
User Tools (System Settings)
❖ Copier / Document Server Auto Reset Timer (copier/Document Server)
Specifies the time to elapse before copier and Document Server modes reset.
Note
❒ If [Off] is selected, the machine does not automatically switch to the user
code entry screen.
❒ Default: On, 60 seconds
❒ The time can be set from 10 to 999 seconds, using the number keys
❖ Facsimile Auto Reset Timer (facsimile)
Specifies the time to elapse before the facsimile mode resets.
Note
❒ Default: On, 30 seconds
❒ The time can be set from 30 to 999 seconds, using the number keys.
4
❖ Printer Auto Reset Timer (printer)
Specifies the time to elapse before the printer function resets.
Note
❒ If [Off] is selected, the machine does not automatically switch to the user
code entry screen.
❒ Default: On, 60 seconds
❒ The time can be set from 10 to 999 seconds, using the number keys.
❖ Scanner Auto Reset Timer (scanner)
Specifies the time to elapse before the scanner function resets.
Note
❒ If [Off] is selected, the machine does not automatically switch to the user
code entry screen.
❒ Default: On, 60 seconds
❒ The time can be set from 10 to 999 seconds, using the number keys
❖ Set Date
Set the date for the copier's internal clock using the number keys
Note
❒ To change between day, month, and year, press [←
←] and [→
→].
❖ Set Time
Set the time for the copier's internal clock using the number keys
Note
❒ To change between hours, minutes and seconds, press [←
←] and [→
→].
❒ Enter the time using the 24–hour format (in 1 second increments).
62
ThemisC1_EN_zentai_pre_FM.book Page 63 Thursday, June 30, 2005 8:21 PM
Settings You Can Change with User Tools
❖ Auto Logout Timer
You can specify whether or not to automatically log out a user when the user
does not operate the machine for a specified period of time after logging in.
Note
❒ Default: On, 60 seconds
❒ When [On] is selected, the time can be set from 10 to 999 seconds, in one second increments, using the number keys
Administrator Tools
Administrator Tools are used by the administrator. To change these settings,
contact the administrator.
We recommend specifying Administrator Authentication before making Administrator Tools settings.
See Security Reference.
4
❖ User Authentication Management
• User Code Authentication
Using User Code Authentication, you can limit the available functions and
supervise their use.
When using User Code Authentication, register the user code.
See p.74 “Authentication Information”.
• Copy:Full Color/Black & White/Single Color/Two-color
• Printer:Color/Black & White/Printer: PC Control
•
•
•
•
Note
❒ Using the Printer PC Control function, you can obtain a log of prints corresponding to the codes entered using the printer driver.
❒ If User Code Authentication has been specified, Auto Color Selection
cannot be used.
• Other functions:Document Server/Facsimile/Scanner
Basic Authentication
Windows Authentication
LDAP Authentication
Off
Note
❒ Default: Off
Reference
For details about Basic Authentication, Windows Authentication, and
LDAP Authentication, see Security Reference.
❖ Administrator Authentication Management
See Security Reference.
63
ThemisC1_EN_zentai_pre_FM.book Page 64 Thursday, June 30, 2005 8:21 PM
User Tools (System Settings)
❖ Program / Change Administrator
See Security Reference.
❖ Key Counter Management
You can specify that functions that you want to manage with the key counter.
❖ Extended Security
You can specify whether or not to use the extended security functions. For details about the extended security functions, see Security Reference.
❖ Display / Print Counter
Allows you to view and print the various counters.
• Display/Print Counter
Displays counters for each functions (Total, Copier, Facsimile, Printer,
A3/DLT, Duplex, Staple).
• Print Counter List
Prints out a list of counters for each functions.
• To print the counter list
} key.
A Press the {User Tools/Counter}
B Press [System Settings].
C Press [Administrator Tools].
D Press [Display / Print Counter].
E Press [Print Counter List].
4
F
G
Press the {Start}
} key.
Press [Exit].
❖ Display / Clear / Print Counter per User
Allows you to view and print the various counters accessed with users and to
set the values to 0.
64
Note
❒ Press [U
UPrev.] and [T
TNext] to show all counters.
• Print Counter for All Users
Prints the counter values for all the users.
• Clear Counter for All Users
Sets the counter value for all the users.
• Print Counter per User
Prints the counter values for each user.
• Clear Counter per User
Sets the counter value for each user.
ThemisC1_EN_zentai_pre_FM.book Page 65 Thursday, June 30, 2005 8:21 PM
Settings You Can Change with User Tools
Note
❒ To print a list for each user, see p.76 “Printing the Counter for Each User
Code”.
❖ Address Book Management
You can add, change or delete information registered in the Address Book.
For details, see p.69 “Registering Addresses and Users for Facsimile/Scanner
Functions”.
• [Program / Change]
You can register and change names as well as user codes.
• Names
You can register a name, key display, registration number, and title selection.
• Auth. Info
You can register a user code, and specify the functions available to each
user code. You can also register user names and passwords to be used
when sending e-mail, sending files to folders, or accessing an LDAP server.
• Protection
You can register a protection code.
• Fax Dest.
You can register a fax number, international TX mode, fax header, label insertion, IP-Fax destination, and protocol.
• E-mail
You can register an e-mail address.
• Folder
you can register the protocol, path, port number, and server name.
• Add to Group
You can put names registered in the Address Book into a group.
• [Delete]
You can delete a name from the Address Book.
4
Note
❒ You can register up to 2,000 names.
❒ You can register up to 500 user codes.
❒ You can also register user codes from SmartDeviceMonitor for Admin.
❖ Address Book: Program / Change / Delete Group
Names registered in the Address Book can be added into a group.
You can then easily manage the names registered in each group. For details,
see p.96 “Registering Names to a Group”.
• [Program / Change]
You can register new groups, or changes a group name, key display, title
selection or registration number.
• [Delete]
You can delete a group.
65
ThemisC1_EN_zentai_pre_FM.book Page 66 Thursday, June 30, 2005 8:21 PM
User Tools (System Settings)
Note
❒ You can register up to 100 groups.
❒ You can also group users using a Web browser. For more information, see
the Web Browser help.
❖ Address Book: Program / Change / Delete Transfer Request
You can register fax destinations for the Transfer Request function in facsimile mode.
For details about operations, see p.103 “Registering the Transfer Request”.
• [Program / Change]
This registers new transfer requests and receiving stations, or changes the
transfer request name, key name, title selection, registration number, fax
destination, IP-Fax destination, or e-mail address.
• [Delete]
Deletes a transfer request.
4
Note
❒ You can register up to 10 transfer requests.
❖ Address Book: Change Order
You can change the order of the names in the Address Book.
Note
❒ You can rearrange the order of items that are on the same page, but you
cannot move the items to another page. For example, you cannot move an
item from “PLANNING” ([OPQ]) to “DAILY” ([CD]).
A Press the {User Tools/Counter}
} key.
B Press [System Settings].
C Press [Administrator Tools], and then press [T
TNext].
D Press [Address Book: Change Order].
E Press the name key to be moved.
F
66
Note
❒ You can also select a name using the number keys.
Press the name key in the place that you want to move to.
ThemisC1_EN_zentai_pre_FM.book Page 67 Thursday, June 30, 2005 8:21 PM
Settings You Can Change with User Tools
The name selected in step E moves to the place selected in step F, and the
keys for other names will be shifted accordingly.
Note
❒ You can also select a name using the number keys.
❖ Print Address Book: Destination List
You can print the list of names registered in the Address Book.
• Print in Title 1 Order
Prints a list of the names according to the order in Title 1.
• Print in Title 2 Order
Prints a list of the names according to the order in Title 2.
• Print in Title 3 Order
Prints a list of the names according to the order in Title 3.
• Print Group Dial List
Prints a list of the groups registered.
A Select the print format.
B To print on two-sided pages, select [Print on 2 Sides].
C Press the {Start}
} key.
The list is printed.
4
❖ Address Book: Edit Title
You can edit the title to locate the desired user easily.
A Press the {User Tools/Counter}
} key.
B Press [System Settings].
C Press [Administrator Tools], and then press [T
TNext].
D Press [Address Book: Edit Title].
E Press the title key to be changed.
F
G
Enter the new name, and then press [OK].
Press [OK].
67
ThemisC1_EN_zentai_pre_FM.book Page 68 Thursday, June 30, 2005 8:21 PM
User Tools (System Settings)
❖ Address Book: Select Title
You can specify the title to select a name.
Note
❒ Default: Title 1
❖ Auto Delete File
You can specify whether documents stored in the Document Server will or
will not be deleted after a specified period of time.
❒
❒
❒
❒
❒
4
Note
Default: Yes After 3 day(s)
If you select [Yes], documents stored subsequently will be deleted.
If you select [No], documents will not be deleted automatically.
If you select [Yes], enter a number of days in the range of 1 - 180.
The default setting is three days, which means documents will be deleted
three days (72 hours) after they have been stored.
❖ Delete All Files
All documents stored in Document Server will be deleted.
Note
❒ Even if a password has been set, all documents will be deleted.
❒ A confirmation dialog box will appear. To delete all documents, select
[Yes].
❖ Program / Change / Delete LDAP Server
See “Program / Change / Delete LDAP Server”, Network Guide.
❖ Use LDAP Server
You can specify whether or not to use the LDAP server.
Note
❒ Default: Off
❒ When Use LDAP Server is set to Off, [Search LDAP] will not appear on the
searching display.
❖ AOF (Always On)
Specify whether or not to use Auto Off function.
Note
❒ Default: On
❒ For details about this function, contact your service representative.
❖ Firmware Version
You can check the version of the softwares installed in this machine.
68
ThemisC1_EN_zentai_pre_FM.book Page 69 Thursday, June 30, 2005 8:21 PM
5. Registering Addresses and Users
for Facsimile/Scanner Functions
Address Book
Registering information such as the
names of users and their e-mail addresses in the Address Book allows
you to manage them easily.
Important
❒ Address Book data is stored on the
hard disk. It can be lost if there is
some kind of hard disk failure. The
manufacturer shall not be responsible for any damages resulting
data loss.
Note
❒ You can also use a Web browser to
register names in the Address
Book. With the SmartDeviceMonitor for Admin, you can register
multiple names at the same time.
❒ Using [Address Management Tool] in
SmartDeviceMonitor for Admin,
you can backup Address Book data. We recommend backing up
data when using the Address
Book.
Reference
For details about using a Web
browser, see the Web browser
Help.
For details about SmartDeviceMonitor for Admin and how to install it, see Printer Reference.
For operating instructions, see
SmartDeviceMonitor for Admin
Help.
You can register and manage the following items in the Address Book:
❖ Name
You can register the name of the
user and the key display. This is
the basic information required for
managing user of the machine.
❖ Authentication Information
You can register user codes in order to restrict particular functions
to certain users, and to check their
use of each function. You can also
register login user names and login
passwords to be used when sending e-mail, sending to folders, or
accessing an LDAP server.
❖ Fax Dest.
You can register fax numbers, line,
fax header and select label insertion.
When using IP-Fax, you can register the IP-Fax destination and select the protocol.
• Fax Destination
69
ThemisC1_EN_zentai_pre_FM.book Page 70 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
• IP-Fax Destination
❖ Add to Group
You can put registered e-mail and
folder destinations into a group for
easier management.
❖ E-mail
You can register e-mail destinations in the Address Book.
Managing names in the Address Book
❖ Folder
You can register the protocol, path
name and server name.
• SMB
5
• FTP
❖ Protection
You can set protection codes to
stop sender's name from being
used or folders from being accessed without authorization.
70
By registering a name and key display beforehand, you can specify
email and folder destinations simply
by selecting the name key.
See p.72 “Registering Names”.
Sending fax by Quick Dial
Register a fax number in the Address
Book so you can specify it only by selecting the fax destination, shown on
the fax initial display when sending a
fax. When label insertion is set to
“ON”, the receiver's name and standard messages are printed on the fax
message when it is received at the
other end.
By registering IP-Fax destinations in
the Address Book, you can specify a
destination simply by selecting it
from the destinations that appear in
the initial fax display.
Registered IP-Fax numbers can be
used and printed as sender’s IP-Fax
numbers.
See p.78 “Fax Destination”.
ThemisC1_EN_zentai_pre_FM.book Page 71 Thursday, June 30, 2005 8:21 PM
Address Book
Sending e-mail by Quick Dial
Managing users and machine usage
By registering e-mail addresses in the
Address Book, you can specify e-mail
destinations simply by selecting them
from the fax initial display when
sending a document by internet fax.
You can also specify an e-mail address by selecting the destination
shown on the initial scanner display
when sending a document using the
scanner function.
A registered e-mail address can be
used as the sender's address, and the
sender's address are automatically
entered in the “From” field of an
email header.
See p.86 “E-mail Destination”.
Register user codes to limit users to
the following functions and check
their use of each function:
• Copier
• Document Server
• Facsimile
• Scanner
• Printer
See p.74 “Authentication Information”.
5
Sending scanned files to a shared folder
directly
After registering the path name, user
name and password, you can connect
to a shared folder simply by selecting
the destination shown on the initial
scanner display whenever sending
files using the scanner function to a
shared folder.
To share the folder using Windows,
select the SMB protocol.
To register the folder to the FTP server, select the FTP protocol.
See p.89 “Registering Folders”.
Preventing unauthorized user access to
shared folders from the machine
After registering a protection code,
you can specify the object of protection to prevent an e-mail destination
from being used without permission.
You can prevent unauthorized access
to registered folders. See p.101 “Registering a Protection Code”.
71
ThemisC1_EN_zentai_pre_FM.book Page 72 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
Registering Names
The user name is useful for selecting a
destination when sending faxes or email. You can also use it as a folder
destination.
H Press the key for the classification
you want to use under Select Title.
Registering a Name
A Press the {User Tools/Counter}} key.
B Press [System Settings].
5
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Press [New Program].
F Press [Change] on the right of the
Name.
The name entry display appears.
G Enter
the name, and then press
[OK].
Note
❒ The name can be used for documents in the Document Server.
For details about the Document
Server, see p.39 “Using the Document Server”.
Reference
p.153 “Entering Text”
72
Note
❒ The keys you can select are as
follows:
• [Freq.]… Added to the page
that is displayed first.
• [AB], [CD], [EF], [GH], [IJK],
[LMN], [OPQ], [RST], [UVW],
[XYZ], [1] to [10]… Added to
the list of items in the selected title.
❒ You can select [Freq.] and one
more page for each title.
I To continue registering the name,
press [Continue to Program], and
then repeat the procedure from
step F.
J Press [OK].
K Press [Exit].
L Press the {User Tools/Counter}} key.
Changing a Registered Name
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
ThemisC1_EN_zentai_pre_FM.book Page 73 Thursday, June 30, 2005 8:21 PM
Registering Names
E Select
the registered name you
want to change.
Press the name key, or enter the
re g is t e re d n u m be r us in g t he
number keys
Note
❒ If you press , you can search
by the registered name, user
code, folder name or e-mail address.
To change the name or key
display
A Press [Change] on the right of
the name or key display.
B Enter the name or key display,
and then press [OK].
Reference
p.153 “Entering Text”
To change the title
A Press the key for the classification you want to use from Select Title.
Deleting a Registered Name
If you delete a name, data associated
with that name, such as e-mail addresses, fax number, and folder
name, is also deleted.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Press [Delete].
F Select the name you want to de-
5
lete.
Press the key, or enter the registered number using the number
keys
G Press [Yes].
H Press [Exit].
I Press the {User Tools/Counter}} key.
F Press [OK].
G Press [Exit].
H Press the {User Tools/Counter}} key.
73
ThemisC1_EN_zentai_pre_FM.book Page 74 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
Authentication Information
Register user codes to limit users to
the following functions and check
their use of each function:
• Copier
• Document Server
• Facsimile
• Scanner
• Printer
Note
❒ The number of copies made of documents stored in the Document
Server using the facsimile function
is counted for each user code. This
allows you to check each user's usage.
5
❒ The number of copies scanned using the scanner function is counted
for each user code. This allows you
to check each user's usage.
❒ To automatically register the printer driver user code, select [PC Control] for the printer in User Code
Authentication. To use the user
code set in User Tools, select [Black
& White] or [Color]. Set the user
codes registered in User Tools for
the printer driver. See p.63 “User
Authentication Management”.
Reference
For details about setting user codes
for the printer driver, see Printer
Reference or the printer driver
Help.
Important
❒ The functions associated with each
user code are the same. If you
change or delete user codes, management data and limits associated
with that code become invalid.
74
Registering a New User Code
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Press the name whose code is to
be registered, or enter the registered number using the number
key.
Note
❒ To register the name, see p.72
“Registering a Name”.
F Press [Auth. Info].
G Enter the user code using the number
keys, and then press [#].
Note
❒ If you make a mistake, press
[Clear] or the {Clear/Stop}
} key,
and then enter the code again.
ThemisC1_EN_zentai_pre_FM.book Page 75 Thursday, June 30, 2005 8:21 PM
Authentication Information
H Press [TTNext] twice.
I Select the functions
to be used
with the user code from Available
Functions.
❒ To change the name, key display and title, see p.72 “Changing a Registered Name”.
F Press [Auth. Info].
G Press [Change], and then enter the
new user code using the number
keys
J Press [OK].
Note
❒ To continue registering user
codes, repeat the procedure
from step E.
K Press [Exit].
L Press the {User Tools/Counter}} key.
Changing a User Code
H Press [#].
A Press [T
TNext] twice.
B Press the key to select the functions to enable them.
Note
❒ Even if you change a user code, the
counter value will not be cleared.
Note
❒ Press the key to highlight it,
and then the function is enabled. To cancel a selection,
press the highlighted key.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter}} key.
D Press [Address Book Management].
E Select the registered user code
Deleting a User Code
press [T
TNext].
you want to change.
Press the name key, or enter the
re g is t e re d n u m be r us in g t he
number keys
Note
❒ If you press , you can search
for a user by name/index, user
code, fax number, or e-mail address.
5
To change the available functions
Note
❒ After clearing the user code, the
counter is automatically cleared.
❒ To delete a name from the Address
Book entirely, see p.73 “Deleting a
Registered Name”.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
75
ThemisC1_EN_zentai_pre_FM.book Page 76 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose code is to
be deleted.
Press the name key, or enter the
re g is t e re d n u m be r us in g t he
number keys
F Press [Auth. Info].
G Press [Change] to delete the user
code, and then press [#].
Printing the Counter for Each
User Code
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools].
D Press [Display / Clear / Print Counter
per User].
E Select
a user code from the left
side of the display.
5
H Press [OK].
I Press [Exit].
J Press the {User Tools/Counter}} key.
Note
❒ Press [Select All on the Page] to select all user codes on the page.
F Press [Print Counter List] under Per
User.
Displaying the Counter for
Each User Code
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools].
D Press [Display / Clear / Print Counter
per User].
E Select
[Copy Counter], [Print Counter], [Transmission Counter] or [Scanner Counter].
Counters for individual function
usage under each user code appear.
76
Note
❒ Enter the user code, and then
press [#] if the user code is registered.
G Select the function usage you want
to print from [Copy Counter], [Print
Counter], [Transmission Counter], and
[Scanner Counter].
H Press [Print].
ThemisC1_EN_zentai_pre_FM.book Page 77 Thursday, June 30, 2005 8:21 PM
Authentication Information
To print the number of prints for all
user codes
To clear the number of prints
made under a user code
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools].
D Press [Display / Clear / Print Counter
A Select the user code from the
left side of the display.
per User].
E Press [Print Counter List] under All
Users.
Note
❒ Press [Select All on the Page] to
select all user codes on the
page.
B Press [Clear] under Per User.
C Select the function usage you
want to clear from [Copy Counter], [Print Counter], [Transmission
Counter], and [Scanner Counter].
D Press [OK].
5
To clear the number of prints for
all user codes
Note
❒ Enter the user code, and then
press [#] if the user code is registered.
A Press [Clear] under All Users.
F Select the function usage you want
to print from [Copy Counter], [Print
Counter], [Transmission Counter], and
[Scanner Counter].
G Press [Print].
Clearing the Number of Prints
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools].
D Press [Display / Clear / Print Counter
B Select the function usage you
want to clear from [Copy Counter], [Print Counter], [Transmission
Counter], and [Scanner Counter].
C Press [OK].
F Press [Exit].
G Press the {User Tools/Counter}} key.
per User].
E Select the user code to clear.
77
ThemisC1_EN_zentai_pre_FM.book Page 78 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
Fax Destination
Register a fax destination so you do
not need to enter fax numbers each
time, and can send documents that
have been scanned in using the facsimile function.
• It is easy to select the fax destination if you register “Name” and
“Key Display” for the fax destination.
• You can register fax destinations
by selecting them from redial function.
• You can register fax destinations as
a group.
Registered Fax numbers can be used
as sender's Fax numbers.
There are two types of fax destination, as shown below:
• Fax Destination
Select this to send the fax over the
telephone network.
• IP-Fax
Select this to send the fax to a machine on a TCP/IP network.
5
Limitation
❒ You cannot send the fax to a machine on another network if that
network is behind a firewall.
❖ Fax Destination
You can program the following
items in a fax destination:
• Fax number
Registers the destination's fax
number. You can enter a fax
number using up to 128 digits.
You must include every digit in
the number.
78
• SUB Code
Registering a SUB Code allows
you to use Confidential Transmission to send messages to the
other fax machines which support a similar function called
“SUB Code”. See “SUB Code”,
Facsimile Reference <Advanced
Features>.
• SEP Code
Registering a SEP Code allows
you to use Polling Reception to
receive faxes from the other fax
machines which support Polling Reception. See “SEP Code”,
Facsimile Reference <Advanced
Features>.
• Line
If the optional extra G3 interface
unit is installed, you can select
the line type per destination.
• Fax header
You can select to print a fax
header on fax messages the other party receives. The default is
“1st Name”. See Facsimile Reference <Advanced Features>.
• Label insertion
With this function you can have
the receiver's name printed on
the message when it is received
at the other end. The name is
printed at the top of the page
and will be preceded by “To”.
You can also have a standard
message stamped on the second
and third lines after that.
Note
❒ Fax header and label insertion are also printed when
sending by e-mail using the
fax function.
ThemisC1_EN_zentai_pre_FM.book Page 79 Thursday, June 30, 2005 8:21 PM
Fax Destination
❒ You can program a standard
message other than those
registered in the machine.
See “Programming, Changing, and Deleting Standard
Messages”, Facsimile Reference <Advanced Features>.
• International TX mode
When setting the International
TX mode to [On], the machine
transmits more carefully by
lowering transmission speed.
However, communication
times increase.
❖ IP-Fax Destination
You can program the following
items in an IP-Fax Destination:
Note
❒ This setting only works if the IP
fax function has been selected.
• IP-Fax
Register the IP-Fax destination.
You can register the name using
up to 128 characters. You must
make this setting when using
IP-Fax.
• SUB Code
Registering a SUB Code allows
you to use Confidential Transmission to send messages to the
other fax machines which support a similar function called
“SUB Code”. See “SUB Code”,
Facsimile Reference <Advanced
Features>.
• SEP Code
Registering a SEP Code allows
you to use Polling Reception to
receive faxes from the other fax
machines which support Polling Reception. See “SEP Code”,
Facsimile Reference <Advanced
Features>.
• Select Protocol
Select the protocol for the IPFax transmission.
Registering a Fax Destination
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
5
press [T
TNext].
D Press [Address Book Management].
E Select the name whose fax desti-
nation you want to register.
Press the name key, or enter the
r e gi st e re d n u m b er us in g t h e
number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To register the name, key display, and title, see p.72 “Registering a Name”.
F Press [Fax Dest.].
G Enter the fax number
using the
number keys, and then press [OK]
under Facsimile No..
79
ThemisC1_EN_zentai_pre_FM.book Page 80 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
You need to register the user code
in advance. ⇒ p.74 “Registering a
New User Code”
A Press [Protection].
B Press [Sender].
C Press [OK].
C Enter a SEP Code using the
number keys, and then press
[OK].
D To enter a password, press
[Ch an ge] u n d er P ass w o rd
(PWD).
E Enter a password using the
number keys, and then press
[OK].
F Press [OK].
To select the line
To set the International TX Mode
A Press [Select Line].
A Press [Change] under International TX Mode.
B Select [Off] or [On], and then
press [OK].
To use the Fax destination as the
sender
5
B Select the line, and then press
[OK].
To program the SUB Code
A Press [Adv. Features], and then
select [SUB Code].
B Press [Change] under TX SUB
Code.
C Enter a SUB Code using the
number keys, and then press
[OK].
D To enter a password, press
[Cha ng e] u n de r Pa ss w o rd
(SID).
E Enter a password using the
number keys, and then press
[OK].
F Press [OK].
To program the SEP Code
80
A Press [Adv. Features], and then
select [SEP Code].
B Press [Change] under RX SEP
Code.
To select the fax header
Note
❒ You can register the fax header
in Program Fax Information in
the system settings for Facsimile Features. See “Program ming”, Facsimile Reference <Basic
Features>.
A Press [Change] under Fax Header.
B Select [1st Name] or [2nd Name],
and then press [OK].
To set label insertion
When Label Insertion is set to ON,
the receiver's name and standard
messages are printed on the fax
message when it is received at the
other end.
A Press [Change] under Label Insertion.
B Select [On].
C Press [Change] under Line 2.
ThemisC1_EN_zentai_pre_FM.book Page 81 Thursday, June 30, 2005 8:21 PM
Fax Destination
D Select a standard message to
print on the second line. To
stamp a customized message,
press [Custom Message].
E Enter a message, and then press
[OK].
Reference
p.153 “Entering Text”
F Press [OK].
G Press [Change] under Line 3.
H Select a standard message, and
then press [OK].
I Press [OK].
H Press [OK].
E Select the name whose fax desti-
nation you want to change.
Press the name key, or enter the
r e gi st e re d n u m b er us in g t h e
number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To change the name, key display and title, see p.72 “Changing a Registered Name”.
F Press [Fax Dest.].
G Change the settings.
5
To change the fax number
A Press [Change] under Facsimile
No..
Note
❒ When a group is registered, you
can also add this fax destination
to the group. See p.96 “Registering Names to a Group”.
I Press [Exit].
J Press the {User Tools/Counter}} key.
Changing a Registered Fax
Destination
B Enter the new fax number using the number keys, and then
press [OK].
To change the line
A Press [Select Line].
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
B Select the line.
C Press [OK].
81
ThemisC1_EN_zentai_pre_FM.book Page 82 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
To change the SUB Code
A Press [Adv. Features].
B Press [SUB Code].
C Press [Change] under TX SUB
Code.
D Enter the new SUB Code, and
then press [OK].
E To change the password, press
[Cha ng e] u n de r Pa ss w o rd
(SID).
F Enter the new password, and
then press [OK].
G Press [OK].
5
To change the SEP Code
A Press [Adv. Features].
B Press [SEP Code].
C Press [Change] under RX SEP
Code.
D Enter the new SEP Code, and
then press [OK].
E To change the password, press
[Cha ng e] u n de r Pa ss w o rd
(PWD).
F Enter the new password, and
then press [OK].
G Press [OK].
To change the fax header
A Press [Change] under Fax Header.
B Select the new fax header, and
then press [OK].
To change the label insertion
A Press [Change] under Label Insertion.
B Press [Change] under Line 2.
82
C Select the new standard message or press [Custom Message]
to enter the new message.
D Press [OK].
E Press [Change] under Line 3.
F Select the new standard message, and then press [OK].
G Press [OK].
H Press [OK].
Note
❒ To change the name, key display and title, see p.72 “Changing a Registered Name”.
I Press [Exit].
J Press the {User Tools/Counter}} key.
Deleting a Registered Fax
Destination
Note
❒ If you delete a destination that is a
specified delivery destination,
messages to its registered Personal
Box, for example, cannot be delivered. Be sure to check the settings
in the fax function before deleting
any destinations.
❒ To delete a name entirely, see p.73
“Deleting a Registered Name”.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose fax desti-
nation you want to delete.
Press the name key, or enter the
r e gi st e re d n u m b er us in g t h e
number keys.
ThemisC1_EN_zentai_pre_FM.book Page 83 Thursday, June 30, 2005 8:21 PM
Fax Destination
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To delete the name, key display,
and title, see p.73 “Deleting a
Registered Name”.
F Press [Fax Dest.].
G Press [Change] under Facsimile No..
H Press [Delete All], and then press
[OK].
E Select
the name whose IP-Fax
destination you want to register.
Press the name key, or enter the
r e gi st e re d n u m b er us in g t h e
number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To register the name, key display, and title, see p.72 “Registering a Name”.
F Press [Fax Dest.]
G Press [IP-Fax].
H Enter the IP-Fax destination and
5
then press [OK].
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter}} key.
Registering an IP-Fax
Destination
Reference
For details about sending an IPFax, see Facsimile Reference <Basic
Features>.
To use the IP-Fax destination as
the sender
A Press [Protection].
B Press [Sender].
C Press [OK].
A Press the {User Tools / Counter}} key.
To program the SUB Code
B Press [System Settings].
C Press [Administrator Tools], and then
A Press [Adv. Features], and then
select [SUB Code].
B Press [Change] under TX SUB
Code.
C Enter a SUB Code using the
number keys, and then press
[OK].
D To enter a password, press
[Ch an ge] u n d er P ass w o rd
(SID).
press [T
TNext].
D Press [Address Book Management].
83
ThemisC1_EN_zentai_pre_FM.book Page 84 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
E Enter a password using the
number keys, and then press
[OK].
F Press [OK].
To program the SEP Code
A Press [Adv. Features], and then
select [SEP Code].
B Press [Change] under RX SEP
Code.
C Enter a SEP Code using the
number keys, and then press
[OK].
D To enter a password, press
[Cha ng e] u n de r Pa ss w o rd
(PWD).
E Enter a password using the
number keys, and then press
[OK].
F Press [OK].
5
I Select the protocol for the IPFax
transmission.
J Press [OK].
Changing a Registered IP-Fax
Destination
A Press the {User Tools / Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose IP-Fax
destination you want to change.
Press the name key, or enter the
re g is t e re d n u m be r us in g t he
number keys
84
Note
❒ If you press , you can search
for a user by the registered
name, user code, fax number,
folder name or e-mail address.
❒ To change the name, key display and title, see p.72 “Changing a Registered Name”.
F Press [Fax Dest.].
G Press [IP-Fax].
H Change the settings.
To change the IP-Fax Destination
A Press [Change] under IP-Fax
Destination.
B Enter the new destination using the number keys, and then
press [OK].
To change the SUB Code
A Press [Adv. Features].
B Press [SUB Code].
C Press [Change] under TX SUB
Code.
D Enter the new SUB Code, and
then press [OK].
E To change the password, press
[Ch an ge] u n d er P ass w o rd
(SID).
F Enter the new password, and
then press [OK].
G Press [OK].
To change the SEP Code
A Press [Adv. Features].
B Press [SEP Code].
C Press [Change] under RX SEP
Code.
ThemisC1_EN_zentai_pre_FM.book Page 85 Thursday, June 30, 2005 8:21 PM
Fax Destination
D Enter the new SEP Code, and
then press [OK].
E To change the password, press
[Cha ng e] u n de r Pa ss w o rd
(PWD).
F Enter the new password, and
then press [OK].
G Press [OK].
To change the protocol
A Select the protocol for the IPFax transmission.
I Press [OK].
Deleting a Registered IP-Fax
Destination
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To delete the name, key display,
and title, see p.73 “Deleting a
Registered Name”.
F Press [Fax Dest.].
G Press [Change] under Facsimile No..
H Press [Delete All], and then press
[OK].
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter}} key.
5
Note
❒ If you delete a destination that is a
specified delivery destination,
messages to its registered Personal
Box, for example, cannot be delivered. Be sure to check the settings
in the fax function before deleting
any destinations.
❒ To delete a name entirely, see p.73
“Deleting a Registered Name”.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose IP-fax destination you want to delete. Press
the name key, or enter the registered number using the number
keys.
85
ThemisC1_EN_zentai_pre_FM.book Page 86 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
E-mail Destination
Register e-mail destinations so you
do not need to enter an e-mail address
every time, and can send scan files
from scanner or fax function by email.
• It is easy to select the e-mail destination if you register “Name” and
“Key Display” as the e-mail destination.
• You can register e-mail destinations as a group.
• You can use the e-mail address as
the sender's address when sending
scan files in scanner mode. If you
want to do this, set a protection
code on the sender address to prevent unauthorized access. See
p.101 “Registering a Protection
Code”.
5
Note
❒ You can select an e-mail address
from an LDAP server, and then
register it in the Address Book.
“Sending Scan File by E-mail”,
Scanner Reference.
❒ You can set the machine to send a
Transmission Result Report by email whenever a transmission is
sent. See Facsimile Reference <Advanced Features>.
Registering an E-mail
Destination
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose e-mail ad-
dress you want to register.
Press the name key, or enter the
r e gi st e re d n u m b er us in g t h e
number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To register the name, key display, and title, see p.72 “Registering a Name”.
F Press [E-mail].
86
ThemisC1_EN_zentai_pre_FM.book Page 87 Thursday, June 30, 2005 8:21 PM
E-mail Destination
G Press [Change] under E-mail Address.
H Enter the e-mail address, and then
press [OK].
Entering the e-mail address
A Enter the e-mail address.
B Press [OK].
Using the e-mail address as the
sender
When an e-mail address is entered,
it can be used as the sender's address.
A Press [Protection].
B Press [Sender] on the right side
of Use Name as.
Changing a Registered E-mail
Destination
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose e-mail ad-
dress you want to change.
Press the name key, or enter the
r e gi st e re d n u m b er us in g t h e
number keys
5
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To change the name, key display, and title, see p.72 “Changing a Registered Name”.
F Press [E-mail].
G Press [Change] under E-mail Address.
Reference
p.101 “Registering a Protection Code”
C Press [OK].
I Press [Exit].
J Press the {User Tools/Counter}} key.
Note
❒ When a group is registered, you
can add the e-mail destinations
to the group. See p.96 “Registering Names to a Group”.
H Enter the e-mail address, and then
press [OK].
Reference
p.153 “Entering Text”
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter}} key.
87
ThemisC1_EN_zentai_pre_FM.book Page 88 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
Deleting a Registered E-mail
Destination
To delete a name entirely, see p.73
“Deleting a Registered Name”.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose e-mail address you want to delete.
Press the name key, or enter the
re g is t e re d n u m be r us in g t he
number keys.
5
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To delete the name, key display,
and title, see p.73 “Deleting a
Registered Name”.
F Press [E-mail].
G Press [Change] under E-mail Address.
H Press
[Delete All], and then press
[OK].
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter}} key.
88
ThemisC1_EN_zentai_pre_FM.book Page 89 Thursday, June 30, 2005 8:21 PM
Registering Folders
Registering Folders
By registering a shared folder, you
can send scan files to it directly.
There are two types of protocol you
can use:
• SMB
For sending files to shared Windows folders
• FTP
Use when sending files to an FTP
server.
Note
❒ For details about protocols, server
names, and folder levels, consult
your network administrator.
❒ You can prevent unauthorized users from accessing folders from the
machine. See p.101 “Registering a
Protection Code”.
❒ You can only select either SMB or
FTP. If you change protocol after
finishing your settings, all previous entries are cleared.
Reference
For details about network settings,
see “Setting Up the Machine on a
Network”, Network Guide.
For details about Scan to Folder,
see "Sending Scan Files by Scan to
Folder" Scanner Reference.
Using SMB to Connect
Note
❒ To register a folder in an FTP server, see p.93 “Using FTP to Connect”.
To register an SMB folder
A Press the {User Tools/Counter}} key.
5
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose folder you
want to register.
Press the name key, or enter the
r e gi st e re d n u m b er us in g t h e
number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To register the name, key display, and title, see p.72 “Registering a Name”.
89
ThemisC1_EN_zentai_pre_FM.book Page 90 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
F Press [Auth. Info], and then press
[T
TNext].
N Confirm that [SMB] is selected.
G Press
[Specify Other Auth. Info] on
the right side of Folder Authentication.
Note
❒ When [Do not Specify] is selected,
the SMB User Name and SMB
Password that you have specified in Default User Name /
Password (Send) of File Transfer settings applies. For details,
see "User Tools Menu (System
Settings)", Network Guide.
H Press [Change] under Login User
5
Name.
I Enter
the login user name, and
then press [OK].
Note
❒ You can enter up to 64 characters for the user name.
Reference
p.153 “Entering Text”
J Press [Change] under Login Password.
K Enter the password, and then press
[OK].
Note
❒ You can enter up to 64 characters for the password.
L Enter the password again to confirm, and then Press [OK].
M Press [Folder].
90
Note
❒ To specify a folder, you can either enter the path manually or
locate the folder by browsing
the network.
Reference
p.90 “To locate the folder manually”
p.91 “Using Browse Network to
locate the folder”
To locate the folder manually
A Press [Change] under Path.
B Enter the path where the folder
is located.
Note
❒ Enter the path using this format: “\\ServerName\ShareName\PathName”.
❒ You can also enter an IP address.
❒ You can enter a path using
up to 128 characters.
C Press [OK].
Note
❒ If the format of the entered
path is not correct, a message
appears. Press [Exit], and
then enter the path again.
ThemisC1_EN_zentai_pre_FM.book Page 91 Thursday, June 30, 2005 8:21 PM
Registering Folders
Using Browse Network to locate
the folder
A Press [Browse Network].
The client computers sharing
the same network as the machine appear.
Note
❒ If you have already specified
your user name and password in steps F to L , the
Browse Network display
only lists client computers
you are authorized to access.
B Select a client computer.
Shared folders under it appear.
Note
❒ You can press [Up One Level]
to switch between levels.
C Select the folder you want to
register.
The Logon display appears.
Note
❒ If you have already entered
an authorized user name and
password, the Logon display
will not appear. Proceed to
step F.
D Enter the user name.
Note
❒ This is a user name which is
authorized to access the folder.
E Enter the user's password, and
then press [OK].
The Browse Network display
reappears.
Note
❒ If the entered user name or
password is not correct, a
message appears. Press [Exit],
and then enter the user name
and password again.
F Press [OK].
O Press [Connection Test] to check the
path is set correctly.
P Press [Exit].
Note
❒ If the connection test fails, check
the settings, and then try again.
Q Press [OK].
R Press [Exit].
S Press the {User Tools/Counter}} key.
5
Changing a registered folder
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose folder you
want to change.
Press the user name key, or enter
the registered number using the
number keys
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To change the name, key display, and title, see p.72 “Changing a Registered Name”.
F Press [Folder].
91
ThemisC1_EN_zentai_pre_FM.book Page 92 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
G Select the items you want to change.
To change the protocol
K Press [Exit].
L Press the {User Tools/Counter}} key.
A Press [FTP].
Deleting a registered folder
Note
❒ To delete a name entirely, see p.73
“Deleting a Registered Name”.
B A confirmation message appears.
Press [Yes].
Note
❒ Changing the protocol will
clear all settings made under
the previous protocol.
C Enter each item again.
5
Reference
p.93 “To register an FTP folder”.
Changing items under SMB
A Press [Change] under Path.
B Enter the new path where the
folder is located, and then
press [OK].
Note
❒ You can also use Browse Network to specify a new folder.
For details, see p.91 “Using
Browse Network to locate
the folder”.
H Press [Connection Test] to check the
path is set correctly.
I Press [Exit].
Note
❒ If the connection test fails, check
the settings, and then try again.
J Press [OK].
92
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose folder you
want to delete.
Press the name key, or enter the
r e gi st e re d n u m b er us in g t h e
number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To delete the name, key display,
and title, see p.73 “Deleting a
Registered Name”.
F Press [Folder].
G Press the protocol
which is not
currently selected.
A confirmation message appears.
H Press [Yes].
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter}} key.
ThemisC1_EN_zentai_pre_FM.book Page 93 Thursday, June 30, 2005 8:21 PM
Registering Folders
Using FTP to Connect
Note
❒ To register a shared folder configured in Windows, see p.89 “Using
SMB to Connect”.
To register an FTP folder
A Press the {User Tools/Counter}} key.
G Press
[Specify Other Auth. Info] on
the right side of Folder Authentication.
Note
❒ When [Do not Specify] is selected,
the SMB User Name and SMB
Password that you have specified in Default User Name /
Password (Send) of File Transfer settings applies. For details,
see "User Tools Menu (System
Settings)", Network Guide.
H Press [Change] under Login User
Name.
B Press [System Settings].
I Enter
the login user name, and
then press [OK].
5
Note
❒ You can enter up to 64 characters for the user name.
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose folder you
want to register.
Press the name key, or enter the
re g is t e re d n u m be r us in g t he
number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To delete the name, key display,
and title, see p.72 “Registering a
Name”.
Reference
p.153 “Entering Text”
J Press [Change] under Login Password.
K Enter the password, and then press
[OK].
Note
❒ You can enter up to 64 characters for the password.
L Enter the password again to confirm, and then Press [OK].
M Press [Folder].
N Press [FTP].
F Press [Auth. Info], and then press
[T
TNext].
93
ThemisC1_EN_zentai_pre_FM.book Page 94 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
O Press [Change] under Server Name.
V Press [OK].
W Press [Exit].
X Press the {User Tools/Counter}} key.
Changing a registered folder
P Enter the server name, and then
press [OK].
Note
❒ You can enter a server name using up to 64 characters.
Q Press [Change] under Path.
R Enter the path.
5
Note
❒ You can enter an absolute path,
using this format: “/user/home/username”; or a relative path, using this format:
“directory/sub-directory”.
❒ If you leave the path blank, the
login directory is assumed to be
the current working directory.
❒ You can also enter an IP address.
❒ You can enter a path using up to
128 characters.
S Press [OK].
Note
❒ To change the port number,
press [Change] under Port No..
Enter the port number using the
number keys, and then press [#].
❒ You can enter 1 to 65535.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose folder you
want to change.
Press the name key, or enter the
r e gi st e re d n u m b er us in g t h e
number keys
Note
❒ If you press , you can search
for a user by name/index, user
code, fax number, or e-mail address.
❒ To change the name, key display, and title, see p.72 “Changing a Registered Name”.
F Press [Folder].
G Select the items you want to change.
To change the protocol
A Press [SMB].
T Press [Connection Test] to check the
path is set correctly.
U Press [Exit].
94
Note
❒ If the connection test fails, check
the settings, and then try again.
B A confirmation message appears.
Press [Yes].
ThemisC1_EN_zentai_pre_FM.book Page 95 Thursday, June 30, 2005 8:21 PM
Registering Folders
Note
❒ Changing the protocol will
clear all settings made under
the previous protocol.
C Enter each item again.
Reference
p.89 “To register an SMB
folder”.
Changing items under FTP
A Press [Change] under Port No.
B Enter the new port number,
and then press [#].
C Press [Change] under Server
Name.
D Enter the new server name, and
then press [OK].
E Press [Change] under Path.
F Enter the new path, and then
press [OK].
H Press [Connection Test] to check the
path is set correctly.
I Press [Exit].
Note
❒ If the connection test fails, check
the settings, and then try again.
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose folder you
want to delete.
Press the name key, or enter the
r e gi st e re d n u m b er us in g t h e
number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To delete the name, key display,
and title, see p.73 “Deleting a
Registered Name”.
5
F Press [Folder].
G Press the protocol
which is not
currently selected.
A confirmation message appears.
H Press [Yes].
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter}} key.
J Press [OK].
K Press [Exit].
L Press the {User Tools/Counter}} key.
Deleting a registered folder
Note
❒ To delete a name entirely, see p.73
“Deleting a Registered Name”.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
95
ThemisC1_EN_zentai_pre_FM.book Page 96 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
Registering Names to a Group
You can register names to a group to
enable easy management of e-mail
addresses and folders for each group.
To add names to a group, the groups
must be registered beforehand.
Note
❒ You can register up to 500 names
for each group.
❒ When using Scan to Folder function, you cannot send scan files to a
group with over 50 folders registered.
❒ You can set a protection code to
prevent unauthorized access to the
folders registered in a group. For
details, see p.101 “Registering a
Protection Code”.
5
Registering a New Group
A Press the {User Tools/Counter}} key.
B Press [System Settings].
F Press [Change] under Group Name.
G Enter the group name, and then
press [OK].
The Key Display name is set automatically.
Reference
p.153 “Entering Text”
H Press the title key under Select Title, if necessary.
Note
❒ The keys you can select are as
follows:
• [Freq.]… Added to the page
that is displayed first.
• [AB], [CD], [EF], [GH], [IJK],
[LMN], [OPQ], [RST], [UVW],
[XYZ], [1] to [10]… Added to
the list of items in the selected title.
❒ You can select [Freq.] and one
more page for each title.
I When you want to change the key
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Group].
E Press [New Program].
96
display, press [Change] under Key
Display. Enter the key display,
and then press [OK].
J Press [OK].
K Press [Exit].
L Press the {User Tools/Counter}} key.
ThemisC1_EN_zentai_pre_FM.book Page 97 Thursday, June 30, 2005 8:21 PM
Registering Names to a Group
Registering Names to a Group
The group key that you have selected becomes highlighted, and
the name is added to it.
You can put names that have been
registered in the Address Book into a
group.
When registering new names, you
can also register groups at the same
time.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name to register in a
group.
Press the name key, or enter the
re g is t e re d n u m be r us in g t he
number keys
To remove the name, click the
highlighted group again.
H Press [OK].
I Press [Exit].
J Press the {User Tools/Counter}} key.
You can check the names or groups
registered in each group.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
F Press [Add to Group].
G Select a group to which you want
D Press [Address Book: Program / Change /
to add the name to.
5
Displaying Names Registered
in Groups
press [T
TNext].
Delete Group].
E Select the group where the mem-
bers you want to check is registered.
F Press [Programd. User/Group].
Note
❒ If you press , you can search
for a group by entering the
group name.
All the names registered will be
displayed.
G Press [OK].
97
ThemisC1_EN_zentai_pre_FM.book Page 98 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
H Press [Exit].
I Press the {User Tools/Counter}} key.
Removing a Name from a
Group
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name to remove from a
5
group.
Press the name key, or enter the
re g is t e re d n u m be r us in g t he
number keys
F Press [Add to Group].
G Select the group from which you
J Press the {User Tools/Counter}} key.
Changing a Group Name
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Group].
E Press the group key you want to
change.
F Enter the items.
To change the group name and
key display
A Press [Change] under Group
Name or Key Display.
want to remove the name.
B Enter the new group name or
key display, and then press [OK].
Note
❒ Highlighted keys indicate groups
in which the name has been registered.
The name is removed from the
group.
To change the title
A Press the title key under Select
Title.
To change the registration
number
98
H Press [OK].
I Press [Exit].
A Press [Change] under Registration No..
B Enter the new registration
number us ing the number
keys
C Press [#].
ThemisC1_EN_zentai_pre_FM.book Page 99 Thursday, June 30, 2005 8:21 PM
Registering Names to a Group
G Press [OK].
H Press [Exit].
I Press the {User Tools/Counter}} key.
F Press [Add to Group].
G Select the group which you want
to add to.
Deleting a Group
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
The group key that you have selected becomes highlighted, and
the group is added to it.
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Group].
E Press [Delete].
F Press a group key you want to delete.
G Press [Yes].
H Press [Exit].
I Press the {User Tools/Counter}} key.
Adding a Group to Another
Group
You can add a group to another
group.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Group].
E Select the group that you want to
put into another group.
Press the group key, or enter the
re g is t e re d n u m be r us in g t he
number keys
5
H Press [OK].
I Press [Exit].
J Press the {User Tools/Counter}} key.
Deleting a Group within a
Group
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Group].
E Within the group, select the groups
you want to delete.
Select groups either by pressing
their keys or entering their registration numbers.
F Press [Add to Group].
Keys of groups that contain those
groups you selected in stepE appear reversed and in black.
99
ThemisC1_EN_zentai_pre_FM.book Page 100 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
G Select the groups you want to de-
lete. Keys of selected groups appear reversed and in white.
H Press [OK].
The groups you selected in stepE
are deleted from the groups that
appear reversed and in white.
5
100
ThemisC1_EN_zentai_pre_FM.book Page 101 Thursday, June 30, 2005 8:21 PM
Registering a Protection Code
Registering a Protection Code
You can stop sender's names or folders being accessed by setting a protection code.
You can use this function to protect
the following:
• Folders
You can prevent unauthorized access to folders.
• Sender's names
You can prevent misuse of sender's
names.
Note
❒ To protect the mail sender's name,
the user code must be registered in
advance. For details, see p.74 “Authentication Information”.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To register the name, key display, and title, see p.72 “Registering a Name”.
F Press [Protection].
5
G Press [Destination]
or [Sender] un-
der Use Name as.
Registering a Protection Code
To a Single User
A Press the {User Tools/Counter}} key.
Note
❒ Both [Destination] and [Sender]
can be selected at the same time.
B Press [System Settings].
H Select Protection Object.
C Press [Administrator Tools], and then
I Press [Folder Destination] or [Sender]
press [T
TNext].
D Press [Address Book Management].
E Select the name whose protection
code you want to register.
Press the name key, or enter the
re g is t e re d n u m be r us in g t he
number keys.
under Protection Object.
Note
❒ Both [Folder Destination] and
[Sender] can be selected at the
same time.
101
ThemisC1_EN_zentai_pre_FM.book Page 102 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
J Press
[Change] under Protection
Code.
number keys, and then press [#].
K Enter a protection code using the
number keys, and then press [#].
Note
❒ You can enter up to eight digits.
L Press [OK].
M Press [Exit].
N Press the {User Tools/Counter}} key.
Registering a Protection Code
To a Group User
5
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Group].
E Press the group key you want to
register or enter the registered
number using the number keys.
F Press [Protection].
G Press [Folder Destination] under Protection Object.
H Press
Code.
102
I Enter a protection code using the
[Change] under Protection
Note
❒ You can enter up to eight digits.
J Press [OK].
K Press [Exit].
L Press the {User Tools/Counter}} key.
ThemisC1_EN_zentai_pre_FM.book Page 103 Thursday, June 30, 2005 8:21 PM
Registering the Transfer Request
Registering the Transfer Request
This section describes how to register
the Transfer Station and Receiving
Station used in the fax function's
Transfer Request.
Note
❒ Before you can use Transfer Request, you must program the Polling ID and set the Transfer Report.
S e e “P ro g ra m m i n g a P o l lin g
ID”and “Transfer Report”, Facsimile Reference <Advanced Features>.
❖ Transfer Station
Refers to the machine that receives
the Transfer Request to forward incoming messages to another destination.
❒ You can have up to 30 Receiving
Stations per Transfer Station. If
you specify a Transfer Station
Group, the group counts as a single receiver.
Registering a Transfer
Station/Receiving Station
A Press the {User Tools/Counter}} key.
5
B Press [System Settings].
❖ Receiving Station
Refers to the facsimile or computer
that receives messages from the
Transfer Station.
Limitation
❒ When messages are transferred by
fax, Transfer Stations must be machines of the same manufacturer as
this one, and have the Transfer Station function.
❒ When messages are transferred by
e-mail, Transfer Stations must be
machines of the same manufacturer as this one, and have both the
Transfer Station and Internet Fax
functions.
❒ You cannot use Transfer Request
without programming the fax
number or e-mail address of the
Requesting Party in the Address
Book of the Transfer Stations.
Note
❒ Polling IDs of the Requesting Party
(this machine) and Transfer Stations must be identical.
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Transfer Request].
E Press [New Program].
F Set the Transfer Request's information.
To register the Transfer Request
name and key display
A Press [Change] under Transfer
Request Name or Key Display.
The name entry display appears.
B Enter the Transfer Request name
or key display, and then press
[OK].
103
ThemisC1_EN_zentai_pre_FM.book Page 104 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
Reference
p.153 “Entering Text”
To select the title
A To associate a Transfer Request
name with a title, press the title
key under Select Title.
N Specify the Receiving Stations.
Note
❒ When specifying the Receiving
Stations, use the numbers
stored in Quick Dial keys, or
Groups in the Transfer Station.
Quick Dial
Note
❒ The keys you can select are as
follows:
• [Freq.]… Added to the
page that is displayed
first.
• [AB], [CD], [EF], [GH], [IJK],
[LMN], [OPQ], [RST], [UVW],
[XYZ], [1] to [10]… Added
to the list of items in the
selected title.
❒ You can select [Freq.] and one
more page for each title.
5
G Press [Fax Dest.].
H Enter the items. See step G on p.79
“Registering a Fax Destination”.
I Press [E-mail].
J Enter the items. See steps G and H
on p.86 “Registering an E-mail
Destination”.
K Press [IP-Fax].
L Enter the items. See steps H-J on
p.83 “Registering an IP-Fax Destination”.
M Press [Receiving Statn.].
A Press [q
qQuick Dial].
B Enter the number stored in the
Quick Dial of the Transfer Station using the number keys
For example, to select the destination stored in Quick Dial 01 of
th e Trans fer St ation , ent er
{0}
}{1}
}.
C To specify an additional Receiving Station, press [Add].
Speed Dial
A Press [q
qpSpeed Dial].
B Enter the Speed Dial number
using the number keys.
For example, to select the destination stored in Speed Dial 12 of
th e Trans fer St ation , ent er
{1}
}{2}
}.
Group Dial
A Press [q
qppGroup Dial].
B Enter the Group number using
the number keys
For example, to select the destinations stored in Group 04 of
th e Trans fer St ation , ent er
{0}
}{4}
}.
C To specify an additional Receiving Station, press [Add].
O When you have specified all the
Receiving Stations, press [OK].
104
ThemisC1_EN_zentai_pre_FM.book Page 105 Thursday, June 30, 2005 8:21 PM
Registering the Transfer Request
P Press [Exit].
Q Press the {User Tools/Counter}} key.
Changing a Registered
Transfer Station/Receiving
Station
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Transfer Request].
E Select the name whose Transfer
Station/Receiving Station you
want to change.
Press the name key, or enter the
re g is t e re d n u m be r us in g t he
number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To change the name, key display, and title, see p.72 “Changing a Registered Name”.
Note
❒ If you press , you can search
for a user by Transfer Request
name, fax number, or e-mail address.
F Enter the items.
To change the Transfer Request
name and key display
A Press [Change] under Transfer
Request Name or Key Display.
B Enter the new Transfer Request Name or key display,
and then press [OK].
To change the title
A Press the title key under Select
Title.
5
To change the Fax Station
A Press [Fax].
Proceed to step Awhen messages are transferred by e-mail.
B Change the Transfer Station's
information. See step G on p.81
“Changing a Registered Fax
Destination”.
To change the IP-Fax Station
A Press [IP-Fax].
B Change the Transfer Station's
information. See step H on p.84
“Changing a Registered IP-Fax
Destination”.
To change the E-mail Transfer
Station
A Press [E-mail].
B Change the Transfer Station's
information. See steps G and H
on p.87 “Changing a Registered E-mail Destination”.
105
ThemisC1_EN_zentai_pre_FM.book Page 106 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
To change the Receiving Station
A Press [Receiving Station].
B Select the Receiving Station
you want to change.
C Press [Clear] to clear the number,
and then enter the new number
using the number keys
G Press [OK].
H Press [Exit].
I Press the {User Tools/Counter}} key.
Deleting a Registered Transfer
Station/Receiving Station
5
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Transfer Request].
E Press [Delete].
F Select the name whose Transfer
Station/Receiving Station you
want to delete.
Press the name key, or enter the
re g is t e re d n u m be r us in g t he
number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
or e-mail address.
❒ To delete the name, key display,
and title, see p.73 “Deleting a
Registered Name”.
106
G Press [Yes].
H Press [Exit].
I Press the {User Tools/Counter}} key.
ThemisC1_EN_zentai_pre_FM.book Page 107 Thursday, June 30, 2005 8:21 PM
Registering Authentication
Registering Authentication
SMTP Authentication
For each user registered in the Address Book, you can register a login
user name and login password to be
used when accessing an SMTP server.
Reference
To use an SMTP server, you need
to program it beforehand. For details, see “SMTP Server Settings”,
Network Guide.
Note
❒ When [Do not Specify] is selected for
SMTP Authentication, the User
Name and Password that you have
specified in SMTP Authentication
of File Transfer settings applies.
For details, see “User Tools Menu
(System Settings)", Network Guide.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
Note
❒ To register a name in the Address Book, see p.72 “Registering a Name”.
F Press [Auth. Info].
G Press [Specify Other Auth. Info] Info
on the right side of SMTP Authentication.
H Press [Change] under Login User
Name.
5
I Enter
the login user name, and
then press [OK].
Note
❒ You can enter up to 191 characters for the user name.
❒ When using POP before SMTP
Authentication, you can enter
up to 63 alphanumeric characters.
Reference
p.153 “Entering Text”
J Press [Change] under Login Password.
C Press [Administrator Tools], and then
K Enter the password, and then press
D Press [Address Book Management].
E Press the name you want to regis-
Note
❒ You can enter up to 64 characters for the password.
press [T
TNext].
ter or enter the registered number
using the number keys
[OK].
L Enter the password again to confirm, and then press [OK].
M Press [OK].
107
ThemisC1_EN_zentai_pre_FM.book Page 108 Thursday, June 30, 2005 8:21 PM
Registering Addresses and Users for Facsimile/Scanner Functions
Note
❒ To change the SMTP Authentication settings, repeat steps H to
M.
LDAP Authentication
For each user registered in the Address Book, you can register a login
user name and login password to be
used when accessing an LDAP server.
Reference
To use an LDAP server, you need
to program it beforehand. For details, see “LDAP Server Settings”,
Network Guide.
5
Note
❒ When [Do not Specify] is selected for
LDAP Authentication, the User
Name and Password that you have
specified in Program/Change
LDAP Server of Administrator
Tools settings applies. For details,
see “Program / Change / Delete
LDAP Server”, Network Guide.
A Press the {User Tools/Counter}} key.
Note
❒ To register a name in the Address Book, see p.72 “Registering a Name”.
F Press [Auth. Info], and then press
[T
TNext].
G Press
[Specify Other Auth. Info] on
the right side of LDAP Authentication.
H Press [Change] under Login User
Name.
I Enter
the login user name, and
then press [OK].
Note
❒ You can enter up to 128 characters for the user name.
Reference
p.153 “Entering Text”
J Press [Change] under Login Password.
K Enter
B Press [System Settings].
the password, and then
press [OK].
Note
❒ You can enter up to 128 characters for the password.
L Enter the password again to confirm, and then press [OK].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Press the name you want to regis108
ter or enter the registered number
using the number keys
M Press [OK].
Note
❒ To change the LDAP Authentication settings, repeat steps H to
M.
ThemisC1_EN_zentai_pre_FM.book Page 109 Thursday, June 30, 2005 8:21 PM
6. Troubleshooting
If Your Machine Does Not Operate As You
Want
The following chart contains explanations of common problems and messages.
If other messages appear, follow the instructions displayed.
Note
❒ If you cannot make copies as you want because of the paper type, paper size
or paper capacity problems, use recommended paper. See p.167 “Copy Paper”.
General
Problem
Causes
“Please wait. ” appears
If the power does not come on even
This message appears
when you turn on the oper- after 2 minutes have elapsed, conation switch or change the tact your service representative.
toner cartridge.
Solutions
The display is off.
The screen contrast knob is Set the screen contrast knob to the
turned to the dark position. light position to see the display panel properly.
The machine is in Energy
Saver mode.
} key to canPress the {Energy Saver}
cel Energy Saver mode.
The operation switch is
turned off.
Turn on the operation switch.
Nothing happens when the
operation switch is turned
on.
The main power switch is
turned off.
Turn on the main power switch.
The Earth Leakage Breaker
is set to Off.
Contact your service representative.
Memory is full.
There are too many
scanned pages or stored
files: hard disk capacity is
exceeded.
Press [Delete File] to delete unnecessary documents.
The function status indicator is red.
The function associated
with the red indicator was
interrupted.
Press the function key corresponding to the indicator. Follow the instructions that appear on the control
panel.
109
ThemisC1_EN_zentai_pre_FM.book Page 110 Thursday, June 30, 2005 8:21 PM
Troubleshooting
Problem
Causes
Solutions
The main power indicator
continues blinking and
does not turn off when
pressed.
This occurs in the following cases:
Close the ADF, and check if the machine communicating with a computer.
• The ADF is open.
• The machine is communicating with external
equipment.
• The hard disk is active.
“Self Checking... ”
appears.
The machine is preforming
image adjustment operations.
The machine may perform periodic
maintenance during operations. The
frequency and duration of maintenance depends on the humidity,
temperature, and printing factors
such as number of prints, paper
size, and paper type. Wait for the
machine to get ready.
Original images are printed on the reverse side of
the paper.
You may have loaded the
paper incorrectly.
Load paper correctly. Load paper
into Tray 1-4 with the print side up,
and into the LCT or bypass tray
with the print side down. See p.116
“Orientation-Fixed Paper or TwoSided Paper”.
The back of the printed
sheet is smeared with ink.
The copier's internal parts
may have become smeared
with ink when misfed paper was removed.
Copy (print) a few sheets to remove
the smeared ink.
The guide boards may be
smeared with ink.
Clean the guide boards. See p.146
“Cleaning the Guide Boards”.
The tray's side guides may
not be locked or may not be
set properly.
Check the side guides are locked
and set properly. See p.126 “Changing the Paper Size”.
The tray's end guide may
not be set properly.
Check the end guide is set properly.
See p.126 “Changing the Paper
Size”.
You may have loaded paper of a size not shown on
the paper size selector.
When using paper of a size that cannot be detected automatically, use
Tray Paper Settings to set the paper
size. See p.58 “Tray Paper Size:
(Tray 1-4)” and p.167 “Copy Paper”.
Something has been placed
on the 500- or 1000-sheet
finisher tray.
Do not place anything on the finisher tray. Doing so may cause paper
misfeeds.
6
Misfeeds occur frequently.
110
ThemisC1_EN_zentai_pre_FM.book Page 111 Thursday, June 30, 2005 8:21 PM
If Your Machine Does Not Operate As You Want
Problem
Causes
An error message remains,
even if misfed paper is removed.
When a misfeed message
Clear misfed paper, and then open
appears, it remains until
and close the front cover. See p.121
you open and close the cov- “xClearing Misfeeds”.
er as required.
Solutions
You turned off the main
power switch.
If you turn the machine off before
removing misfed papers, the error
message will reappear after turning
the machine back on. Keep the machine turned on while opening/closing the corresponding tray
and the front cover
When the ADF is open, the
machine switches to LowPower Mode or Sleep
Mode.
Keep the machine turned on while
opening/closing the ADF.
You cannot use paper in
the bypass tray for duplex
printing.
For duplex printing, select Tray 1-4
in copier mode or with the printer
driver.
[1 Sided Copy] is selected for
Paper Type: Tray 1-4.
Select [2 Sided Copy] for Paper Type:
Tray 1-4. See p.59 “Paper Type: Tray
1–4”
—
Contact your service representative.
The user code entry display appears.
Users are restricted by user
codes.
Enter the user code (up to 8-digits),
and then press [#].
The Authentication screen
appears.
Basic Authentication, Win- Enter your login user name and user
dows Authentication, or
password. See p.25 “When the AuLDAP Authentication is
thentication Screen is displayed”.
set.
“You do not have
The use of the function is
restricted to authenticated
users only.
Contact the administrator.
This user code is not allowed to use the function
selected.
Press the {Energy Saver}
} key. Confirm that the display goes off, and
then press the {Energy Saver}
} key
again. The display will return to the
user code entry display.
The entered login user
name or login password is
not correct.
Inquire the user administrator for
the correct login user name and
login password.
The machine cannot perform authentication.
Contact the administrator.
"Cannot detect
original size." appears.
Cannot print in duplex
mode.
You forgot your user code.
the privileges to
use this function.” is displayed.
“You do not have
the privileges to
use this function.” continues to be
displayed even though you
have entered a valid user
code.
Authentication has failed.
6
111
ThemisC1_EN_zentai_pre_FM.book Page 112 Thursday, June 30, 2005 8:21 PM
Troubleshooting
Problem
Causes
Solutions
“Selected files
You have tried to delete
files without the authority
to do so.
Files can be deleted by the person
who created the file. To delete a file
which you are not authorized to delete, contact the person who created
the file.
contain file(s)
that the user does
not have access
privileges to.
Please note that
only the files
with access privileges will be deleted.” is displayed.
Printing Problems
Problem
Action
color are missing in some parts.
• Perform [Clean / Adjust] in the Maintenance menu.
See ⇒ p.147 “Cleaning and Adjusting Internal
Parts”.
• Clean the exposure glass. See ⇒ p.146 “Cleaning
the Exposure Glass”.
6
color lines appear.
White lines appear.
• Clean the dustproof glass. See ⇒ p.148 “Cleaning
the Dustproof Glass”.
• Perform [Clean / Adjust] in the Maintenance menu.
See ⇒ p.147 “Cleaning and Adjusting Internal
Parts”.
• Clean the exposure glass. See ⇒ p.146 “Cleaning
the Exposure Glass”.
The color of the copied image are fainter
than those of the original.
A certain color is printed more vividly
than the others.
The color of the copied image are different from those of the original.
112
Perform the auto color calibration. ⇒ p.138 “Auto
Color Calibration”.
ThemisC1_EN_zentai_pre_FM.book Page 113 Thursday, June 30, 2005 8:21 PM
If Your Machine Does Not Operate As You Want
Document Server
Problem
Solutions
"Scanned pages exceeded
max. number. Do you want
to store the scanned pages as a file?" appears.
The number of scanned pages exceeds the capacity per
file of the Document Server.
You forgot your password.
Contact the administrator.
To store scanned pages as a file, press [Store File].
Scanned data is stored as a file in the Document Server.
If you do not want to store scanned pages, press [No].
Scanned data is deleted.
You cannot find out what is stored in Check the date or time column in the Document Server:
a file.
Select Files to Print display.
Check document content by printing it's first page. Press
the line of the document in the Document Server: Select
Files to Print display, and then press [Print 1st Page] followed by the {Start}
} key.
Memory frequently becomes full.
• Press [Delete File] to delete selected documents to increase available memory.
• Delete documents stored using the scanner function.
See Scanner Reference.
You want to check print quality before making a large print run.
Check print quality by printing out only the first set using the {Sample Copy}
} key.
"Original is being
The copier or scanner function is in use. To cancel a job
6
scanned by another func- in progress, first press [Exit], and then press the {Copy}}
key or {Scanner}
} key. Next, press the {Clear/Stop}
} key.
tion." appears.
When the message "[Stop] key was pressed.
Stop storing?" appears, press [Stop].
Maintenance
Problem
Causes
Solutions
"Used Toner Bottle
Replacement"
The waste toner bottle is
full and it is time to replace
it.
Check your maintenance service
contract.
"Used Toner Bottle
is full."
"Please replace
Used Toner Bottle."
113
ThemisC1_EN_zentai_pre_FM.book Page 114 Thursday, June 30, 2005 8:21 PM
Troubleshooting
BLoading Paper
Note
❒ Fan the paper before loading it in
the tray.
❒ Straighten curled or warped paper
before placing it in the tray.
C Load paper into the tray with the
print side up.
Reference
For paper types and sizes, see
p.167 “Copy Paper”.
Loading Paper into Tray 1 and 2
ZGJS140E
6
Note
❒ You can change the paper size ⇒
p.126 “Changing the Paper Size”
Important
❒ Do not stack paper over the limit mark.
A Pull out the paper tray slowly un-
D Push in the paper tray slowly un-
til it stops.
til it stops.
Loading Paper into Tray 3 and 4
(optional)
A Pull put the paper tray slowly until it stops.
ZGJS120E
B Lower the base panel by pushing
“Push”. When paper is set in the
tray, push down on the paper.
ZGJS150E
ZGJS130E
114
ThemisC1_EN_zentai_pre_FM.book Page 115 Thursday, June 30, 2005 8:21 PM
BLoading Paper
B Load paper into the tray with the
print side up.
B Align the paper and load it in the
tray with the print side up.
ZGJS180E
ZGJS230E
Important
❒ Check that the top of the stack is
not higher than the limit mark
inside the tray.
C Push in the paper tray slowly until it stops.
Important
❒ Align the paper stacks and load
them against the left and right
walls, or a paper misfeed might
occur.
❒ Do not stack paper over the limit mark.
6
C Push the paper tray slowly in un-
Loading Paper into Large
Capacity Tray (optional)
til it stops.
Note
❒ Load copy paper of the same size
and direction in both left and right
side trays.
A Pull out the LCT, slowly until it
stops.
ZGJS170E
115
ThemisC1_EN_zentai_pre_FM.book Page 116 Thursday, June 30, 2005 8:21 PM
Troubleshooting
Orientation-Fixed Paper or Two-Sided Paper
Orientation-fixed (top to bottom) or two-sided paper (for example, letterhead
paper, punched paper, or copied paper) might not print correctly, depending on
how the originals and paper are placed. Select [Yes] in Letterhead Setting under
Copier/Document Server Features, and then place the original and paper as
shown below (see “Letterhead Setting” Copy Reference). When printing with the
printer function, placement orientation is the same.
6
GGH100E
116
ThemisC1_EN_zentai_pre_FM.book Page 117 Thursday, June 30, 2005 8:21 PM
DAdding Toner
DAdding Toner
When Dappears, it is time to add toner.
R WARNING:
• Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers
in accordance with local regulations.
R CAUTION:
• Keep toner (used or unused) and toner containers out of reach of children.
R CAUTION:
• If toner or used toner is inhaled, gargle with plenty of water and move into a
fresh air environment. Consult a doctor if necessary.
R CAUTION:
• If toner or used toner gets into your eyes, flush immediately with large
amounts of water. Consult a doctor if necessary.
R CAUTION:
• If toner or used toner is swallowed, dilute by drinking a large amount of water. Consult a doctor if necessary.
6
R CAUTION:
• Avoid getting toner on your clothes or skin when removing a paper jam or
replacing toner. If your skin comes into contact with toner, wash the affected
area thoroughly with soap and water.
• If toner gets on your clothing, wash with cold water. Hot water will set the
toner into the fabric and may make removing the stain impossible.
If the message "No toner: xxxx,xxxx" is shown on the display, replace the applicable color-toner.
Note
❒ "xxxx,xxxx" is shown as the color of toner is almost empty, and the combination of 1-4 of Yellow, Magenta, Cyan, and Black is displayed.
Important
❒ Fault may occur if you use toner other than the recommended type.
❒ When adding toner, do not turn off the operation switch. If you do, settings
will be lost.
❒ Always add toner when the machine instructs you.
117
ThemisC1_EN_zentai_pre_FM.book Page 118 Thursday, June 30, 2005 8:21 PM
Troubleshooting
Note
❒ The message “DToner is almost empty.” on the display shows a toner
name and the telephone number for ordering.
❒ You can still make about 500 copies after the messages “DToner is almost
empty.”, “Replace Toner Cartridge(s).”, and “Black, Yellow, Magenta, Cyan”
appear cyclically, but replace toner early to prevent poor copy quality.
❒ If “Toner Cartridge is not set properly.” appears, slide the toner cartridge
back and forth twice, and push it until it stops.
❒ The consumption of toner depends on the humidity, temperature and printing factors such as image size, density, number of prints, paper size, and paper type. Moreover, to preserve print quality, this machine automatically
performs periodic maintenance using the toner.
❒ Change all four color-toner cartridges in the same way.
❒ You cannot print immediately after inserting a new cartridge. Allow 6-7 minutes per cartridge.
❒ While loading black toner, the noise of the machine's processing may continue for a while.
Reference
For details about toner storage, see p.143 “Toner Storage”.
6
Removing/Inserting Toner
❖ The yellow/magenta/cian toner
• 1: Open the front cover of the machine.
AFT011S
• 2: Pull the lever and open the green cover.
AFT012S
• 3: Gently pull out the toner cartridge.
AFT033S
118
ThemisC1_EN_zentai_pre_FM.book Page 119 Thursday, June 30, 2005 8:21 PM
DAdding Toner
• 4: Hold a new cartridge and shake it 10 or
12 times.
Note
AFT014S
❒ Do not touch the "metal contact point"
of the cartridge, or it may be damaged.
• 5: Hold the cartridge as shown and tap it 78 times against the palm of your other
hand.
AFT015S
• 6: Carefully remove the tape.
Important
AFT016S
❒ Toner spills if the shutter opens. Take
care to keep the shutter closed when removing the tape.
• 7:Insert the cartridge horizontally, and
gently push it in completely.
6
AFT034S
❖ The black toner
• 1: Open the front cover of the machine.
AFT011S
• 2: Pull the lever and open the green cover.
AFT012S
• 3: Gently pull out the toner cartridge.
AFT013S
119
ThemisC1_EN_zentai_pre_FM.book Page 120 Thursday, June 30, 2005 8:21 PM
Troubleshooting
• 4: Hold a new cartridge and shake it 10 or
12 times.
Note
❒ Do not touch the "metal contact point"
of the cartridge, or it may be damaged.
AFT030S
• 5: Hold the cartridge as shown and tap it 78 times against the palm of your other
hand.
AFT031S
• 6: Carefully remove the tape.
Important
❒ Toner spills if the shutter opens. Take
care to keep the shutter closed when removing the tape.
AFT032S
• 7:Insert the cartridge horizontally, and
gently push it in completely.
6
AFT017S
- Issues When Installing the Toner Cartridge
AFT018S
Make sure the toner cartridge is not misaligned to the left (B). If it is, carefully
lift and move the cartridge to the right so it is located at (A).
Important
❒ If the toner cartridge is misaligned, printing may be affected.
120
ThemisC1_EN_zentai_pre_FM.book Page 121 Thursday, June 30, 2005 8:21 PM
xClearing Misfeeds
xClearing Misfeeds
R CAUTION:
• The fusing section of this machine might be very hot. Caution should be taken when removing misfed paper.
Important
❒ When clearing misfeeds, do not turn off the operation switch. If you do, your
copy settings will be lost.
❒ To prevent misfeeds, do not leave any torn scraps of paper inside the machine.
❒ If paper misfeeds occur frequently, contact your service representative.
Note
❒ More than one misfed area may be indicated. When this happens, check all
the areas indicated. See the following charts:
• A, B, C,D,Y⇒ p.122
• R (500-Sheet Finisher)⇒ p.125
❒ Inside the finisher, or inside the front cover, there is a sticker explaining how
to remove misfed paper.
6
❖ If paper is stuck to the printer's right side heat roller
When you open the internal cover of the duplex unit (right side of the machine), you can see the holes in the upper surface of the development unit (the
part with the warning label). Normally, from here you will be able to see the
orange heat roller. If you can see paper in this area, contact your service representative.
121
ThemisC1_EN_zentai_pre_FM.book Page 122 Thursday, June 30, 2005 8:21 PM
Troubleshooting
6
122
ThemisC1_EN_zentai_pre_FM.book Page 123 Thursday, June 30, 2005 8:21 PM
xClearing Misfeeds
6
AFT005S
123
ThemisC1_EN_zentai_pre_FM.book Page 124 Thursday, June 30, 2005 8:21 PM
Troubleshooting
6
124
ThemisC1_EN_zentai_pre_FM.book Page 125 Thursday, June 30, 2005 8:21 PM
xClearing Misfeeds
6
AFT006S
125
ThemisC1_EN_zentai_pre_FM.book Page 126 Thursday, June 30, 2005 8:21 PM
Troubleshooting
Changing the Paper Size
Preparation
Be sure to select the paper size
with User Tools and the paper size
selector. If you do not, misfeeds
might occur. See p.58 “Tray Paper
Size: (Tray 1-4)”.
B Lower the base panel by pushing
"Push". When paper is set in the
tray, push down on the paper.
Important
❒ If you wish to change the paper
size set in the LCT(optional), contact your service representative.
Note
❒ Procedures for changing the paper
size differ depending on the tray
(paper tray 1, paper tray 2 or the
optional paper tray units). Make
sure you are following the appropriate procedure before you begin.
6
ZGJS130E
C If paper is loaded in the tray, remove it.
D Set
the paper guide lock to the
“unlocked" position.
Reference
For details about paper sizes and
types, see p.167 “Copy Paper”.
Changing the Paper Size of
Tray 1 and 2
A Make sure the paper tray is not in
use. Then, pull out the paper tray
slowly until it stops.
ZJKY280J
E While pressing the release lever,
adjust the side guides to the paper
size.
ZGJS120E
ZGJS210E
126
ThemisC1_EN_zentai_pre_FM.book Page 127 Thursday, June 30, 2005 8:21 PM
Changing the Paper Size
F Pinching
both sides of the end
guide (A
A), move the end guide in
the direction of the arrow (B
B) to
open it.
I Load paper into the tray with the
print side up.
ZGJS140E
ZGJS290E
G Square the paper, and then load it
in the tray with the copying face
down.
Important
❒ Do not stack paper over the limit mark.
J Pushing
the green lever of the
side guide (A
A ), move the side
guide toward the paper stack until it stops (B
B).
6
ZJKY290J
ADL027S
Important
❒ Do not stack paper over the limit mark.
H Pinching
both sides of the end
guide (A
A), move the end guide in
the direction of the arrow (B
B) to
open it.
ZGJS310E
K Confirm that the paper is fixed in
place, and then lock the side
guides.
ZGJS320E
ZGJS290E
127
ThemisC1_EN_zentai_pre_FM.book Page 128 Thursday, June 30, 2005 8:21 PM
Troubleshooting
L Pinching
both sides of the end
guide (A
A), move the end guide toward the paper stack until it stops
(B
B).
C Set the paper guide lock to the unlocked" position.
ZGJS200E
ZGJS330E
Important
❒ Be sure to move the end guide;
otherwise, the paper may misfeed.
D Pushing
the green lever of the
side guide (A
A ), move the side
guide toward you to open it (B
B).
M Slide the paper tray into the print-
6
er carefully until it stops.
Changing the Paper Size of
Tray 3 and 4 (option)
A Pull out the paper tray slowly until it stops.
ZGJS211E
E Pinching
both sides of the end
guide (A
A), move the end guide in
the direction of the arrow (B
B) to
open it.
ZGJS150E
B When paper is set in the tray, remove them.
128
ZGJS220E
ThemisC1_EN_zentai_pre_FM.book Page 129 Thursday, June 30, 2005 8:21 PM
Changing the Paper Size
F Load paper into the tray with the
print side up.
I Pinching
both sides of the end
guide (A
A), move the end guide toward the paper stack until it stops
(B
B).
ZGJS230E
Important
❒ Confirm that the top of the stack
is not higher than the limit mark
inside the tray.
ZGJS250E
Important
❒ Be sure to move the end guide;
otherwise, the paper may misfeed.
G Pushing
the green lever of the
side guide (A
A ), move the side
guide toward the paper stack until it stops (B
B).
J Slide the paper tray into the print-
6
er carefully until it stops.
If you load a paper size that is
not selected automatically
ZGGH240E
H Confirm that the paper is fixed in
place, and then lock the side
guides.
If you load a paper size that is not selected automatically, you need to
specify the paper size with the control
panel.
Following paper sizes that are not selected automatically.
Trays 1 and 2 : A5L, A6L, 11" ×
17"L, 81/2" × 14"L, 8 1/ 2" × 11"K,
51/2" × 81/2"KL, 71/4" × 101/2"KL,
8" × 13"L, 8 1 / 2 " × 13"L, 8 1 / 4 " ×
13"L, 8KL, 16KKL
Trays 3 and 4 *1 : B5 JISL, A5L, 81/2"
× 14"L, 8 1 / 2 " × 11"L, 5 1 / 2 " ×
8 1 / 2 "KL, 7 1 / 4 " × 10 1 / 2 "L, 8" ×
13"L, 81/2" × 13"L, 8 1/ 4" × 13"L,
8KL, 16KKL
Tray 3 *2 : 81/2" × 11"K
*1
ZGJS479E
*2
Paper tray unit (option)
LCT(option)
129
ThemisC1_EN_zentai_pre_FM.book Page 130 Thursday, June 30, 2005 8:21 PM
Troubleshooting
A Press the {User Tools/Counter}} key.
E Select the loaded paper size and
feed direction, and then press
[OK].
B Press [System Settings].
The set paper size and feed direction is displayed.
C Press [Tray Paper Settings].
F Press the {User Tools/Counter}} key.
The initial display is shown.
6
D Select the tray for which you want
to change the paper settings.
Note
❒ Press either of [Tray Paper Size:
Tray 1] to [Tray Paper Size: Tray 4].
130
Important
❒ If you want to print on paper
that is selected automatically after printing on a paper size that
is not selected automatically,
you must return the setting to
“Auto Detect”. Reload the paper, repeat step A to D, and select “Auto Detect" in step E. The
setting is returned to “Auto Detect”.
ThemisC1_EN_zentai_pre_FM.book Page 131 Thursday, June 30, 2005 8:21 PM
d Adding Staples
d Adding Staples
Important
❒ If you use a staple cartridge other than that recommended, staple failure or
staple jams might occur.
Reference
For the type of finisher, refer to “External Options” ⇒ p.21
500-Sheet Finisher
• 1: Open the side cover.
ZGJS795E
6
• 2: Remove the cartridge.
ZGJS796E
• 3: Take out the empty refill in the direction
of the arrow.
ZGJS797E
• 4: Push in the new refill until it clicks.
ZGJS798E
• 5: Pull out the ribbon.
ZGJS799E
131
ThemisC1_EN_zentai_pre_FM.book Page 132 Thursday, June 30, 2005 8:21 PM
Troubleshooting
• 6: Reinstall the cartridge.
• 7: Close the side cover.
ZGJS800E
1000-Sheet Finisher
• 1: Open the front cover of the finisher and
pull out the staple unit.
ZGJS801E
6
• 2: Hold the green lever and pull out the
cartridge gently.
ZGJS802E
• 3: Hold both sides of the cartridge.
• 4: Pull up the upper unit of the cartridge.
ZGJS803E
• 5: Take out the empty refill in the direction
of the arrow.
ZGJS804E
• 6: Align the arrows on the new refill and
the cartridge, and then push in the refill
until it clicks.
ZGJS805E
132
ThemisC1_EN_zentai_pre_FM.book Page 133 Thursday, June 30, 2005 8:21 PM
d Adding Staples
• 7: Push down the upper unit into the cartridge gently.
ZGJS806E
• 8: Pull out the ribbon.
ZGJS807E
• 9: Hold the green lever and reinstall the
cartridge until it clicks.
• 10: Push back the staple unit and close the
front cover of the finisher.
ZGJS808E
6
133
ThemisC1_EN_zentai_pre_FM.book Page 134 Thursday, June 30, 2005 8:21 PM
Troubleshooting
e Removing Jammed Staples
Note
❒ Staples might jam because of curled copy paper. In such a case, try turning
the copy paper over in the tray. If there is no improvement, change to a copy
paper with less curl.
❒ When the 500-Sheet Finisher is installed, after removing jammed staples, staples might not be ejected the first few times you try to use the stapler.
Reference
For the type of finisher, refer to “External Options” ⇒ p.21
500-Sheet Finisher
• 1: Open the side cover.
6
ZGJS795E
• 2: Remove the cartridge.
ZGJS796E
• 3: Open the face plate.
ZGJS810E
• 4: Remove jammed staples.
ZGJS811E
134
ThemisC1_EN_zentai_pre_FM.book Page 135 Thursday, June 30, 2005 8:21 PM
e Removing Jammed Staples
• 5: Reinstall the cartridge.
• 6: Close the side cover.
ZGJS812E
1000-Sheet Finisher
• 1: Open the front cover of the finisher and
pull out the staple unit.
ZGJS801E
6
• 2: Hold the green lever and pull out the
cartridge gently.
ZGJS802E
• 3: Open the face plate of the cartridge.
ZGJS813E
• 4: Remove jammed staples.
ZGJS814E
• 5: Pull down the face plate of the cartridge
until it clicks.
ZGJS815E
135
ThemisC1_EN_zentai_pre_FM.book Page 136 Thursday, June 30, 2005 8:21 PM
Troubleshooting
• 6: Hold the green lever and reinstall the
cartridge until it clicks.
• 7: Push back the staple unit and close the
front cover of the finisher.
ZGJS808E-01
6
136
ThemisC1_EN_zentai_pre_FM.book Page 137 Thursday, June 30, 2005 8:21 PM
Replacing the Stamp Cartridge
Replacing the Stamp Cartridge
When the stamp becomes lighter, replace the cartridge.
C Pull out the old stamp cartridge.
Note
❒ This stamp cartridge is used for
facsimile and scanner functions.
❒ Use the cartridge specified for this
machine.
❒ Do not add ink to the cartridge by
yourself. Neglecting this can cause
ink leakage.
❒ Be sure not to dirty your fingers
with ink from the cartridge.
D Insert the new stamp cartridge.
A Open the ADF unit.
Insert the cartridge until the metal
parts are no longer visible.
6
ZGNH010J
B Open the stamp cover.
1. New Cartridge
E Replace the stamp cover until it
clicks.
ZGNH011J
F Close the ADF unit.
137
ThemisC1_EN_zentai_pre_FM.book Page 138 Thursday, June 30, 2005 8:21 PM
Troubleshooting
Auto Color Calibration
If a certain color is strong or the color
of the copy differs from the original,
adjust the yellow, magenta, cyan and
black balance.
Note
❒ If "DToner is almost empty." is
shown on the display panel, the
test pattern cannot be printed.
A Press the {User Tools/Counter}} key.
B Press [Maintenance].
6
Note
❒ When performing the auto color
calibration from the printer
function, select test patterns
from [600 × 600 dpi], [1800 × 600
dpi] and [1200 × 1200 dpi] and
then press [Start Printing].
❒ The test pattern will be printed
on an A4K, 81/2”× 11”K size
page (If A4K is not available
then A3 L, B4 JISL will be
used.). Make sure to check the
paper set in the paper tray.
❒ The counter will not proceed
when the test pattern is printed.
F Place the test pattern on the exposure glass and press [Start Scanning].
The image will be corrected after
"Please wait." disappears.
C Press [Auto Color Calibration].
D Press [Start] on the “Copier Function”.
Note
❒ When performing the auto color
calibration from the copy function, press [Start] under Copier
Function. When performing
from the printer function, press
[Start] under Printer Function.
E Press [Start Printing] and a test pattern will be printed.
138
Note
❒ The test pattern will not be read
if it is set in the ADF.
❒ Set the test pattern in the following way:
AFT038S
❒ When the ADF is installed, make
sure to set the test pattern on the
exposure glass, and then 2 or 3
white sheets, same size as the
test pattern, above the test pattern.
ThemisC1_EN_zentai_pre_FM.book Page 139 Thursday, June 30, 2005 8:21 PM
Auto Color Calibration
Returning to the previous setting
Note
❒ “Previous Setting” means to return to the previous status before any changes.
A Press [Previous Setting] in the
“Auto Color Calibration .
When returning the auto color
calibration of the copy function,
press [Previous Setting] of the
Copier Function. If returning
the auto color calibration of the
printer function, press [Previous
Setting] of the Printer Function.
6
B Press [Yes].
The settings return to the previous contents.
139
ThemisC1_EN_zentai_pre_FM.book Page 140 Thursday, June 30, 2005 8:21 PM
Troubleshooting
6
140
ThemisC1_EN_zentai_pre_FM.book Page 141 Thursday, June 30, 2005 8:21 PM
7. Remarks
Dos and Don'ts
R WARNING:
• Keep the machine away from
flammable liquids, gases, and
aerosols. A fire or an electric
shock might occur.
R CAUTION:
• Unplug the power cord from the
wall outlet before you move the
machine. While moving the machine, you should take care that
the power cord will not be damaged under the machine.
Important
❒ Do not turn the power off while
the On indicator is lit or blinking.
Doing so may damage the hard
disk.
❒ Before unplugging the power cord
or turning off the main power
sw itc h, m ake sure remaining
m e m ory space is at 100% , a s
shown on the display. See p.28
“Turning Off the Power” and p.28
“Turning Off the Main Power”.
• When you use this machine for a
long time in a confined space without good ventilation, you may detect an odd smell. To keep the
workplace comfortable, we recommend that you keep it well ventilated.
• Do not touch areas on or around
the fusing unit. These areas may
become hot.
• After scanning originals continuously, the exposure glass may become warm—this is not a
malfunction.
• The area around the ventilation
hole might feel warm. This is
caused by exhaust air and is not a
malfunction.
• When the machine is not in use
and in stand-by mode, you may
hear a small noise inside. This is
caused by the image stabilization
process and is not a malfunction.
• Do not turn off the power when
the machine is in operation.
• The machine might not produce
good copy images if condensation
forms inside as a result of rapid
temperature change.
• Do not open the covers of the machine when it is in operation. If you
do, misfeeds might occur.
• Do not move the machine when
the power is on.
• If you operate the machine improperly or a machine failure occurs, settings might be lost. Be sure
to make a note of your machine
settings.
• The supplier shall not be liable for
any loss or damage resulting from
mechanical failure, loss of settings,
or use of the machine.
141
ThemisC1_EN_zentai_pre_FM.book Page 142 Thursday, June 30, 2005 8:21 PM
Remarks
Saving Color Copies
• There is no difference between color prints and color copies in terms of fading. However, for long-term storage, make sure to store them in a binder
away from direct sunlight.
• Toner may melt if a print and a half-dried print are put on top of each other.
• Toner may also melt when using solvent type adhesive agents for pasting
prints.
• When folding prints, toner in the folds will come off.
• Toner may melt if it is placed on mats made of chlorinated plastic in locations
of high temperature for long periods of time.
• Toner may melt if prints are placed in places of extremely high temperatures,
such as near heaters.
7
142
ThemisC1_EN_zentai_pre_FM.book Page 143 Thursday, June 30, 2005 8:21 PM
Toner
Toner
Handling Toner
R WARNING:
• Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers
in accordance with local regulations.
R CAUTION:
• Keep toner (used or unused) and toner containers out of reach of children.
Important
❒ Fault may occur if you use toner other than the recommended type.
Reference
To add toner, see p.117 “DAdding Toner”.
Toner Storage
When storing toner, the following precautions should always be followed:
• Store toner containers in a cool, dry place free from direct sunlight.
• Store on a flat surface.
7
Used Toner
Note
❒ Toner cannot be re-used.
143
ThemisC1_EN_zentai_pre_FM.book Page 144 Thursday, June 30, 2005 8:21 PM
Remarks
Where to Put Your Machine
Machine Environment
Environments to avoid
Choose your machine's location carefully. Environmental conditions
greatly affect its performance.
• Locations exposed to direct sunlight or other sources of strong
light (more than 1,500 lux).
• Locations directly exposed to cool
air from an air conditioner or heated air from a heater. (Sudden temperature changes can cause
condensation to form inside the
machine.)
• Locations close to machines generating ammonia, such as a diazo
copy machine.
• Places where the machine will be
subject to frequent strong vibration.
• Dusty areas.
• Areas with corrosive gases.
Optimum environmental conditions
R CAUTION:
• Keep the machine away from humidity and dust. Otherwise a fire
or an electric shock might occur.
• Do not place the machine on an
unstable or tilted surface. If it topples over, an injury might occur.
R CAUTION:
• If you use the machine in a confined space, make sure there is a
continuous air turnover.
7
• Temperature: 10-32 °C (50-89.6 °F)
(humidity to be 54% at 32 °C, 89.6 °F)
• Humidity: 15-80% (temperature to
be 27 °C, 80.6 °F at 80%)
• A strong and level base.
• The machine must be level within
5 mm, 0.2 inches: both front to rear
and left to right.
• To avoid possible buildup of
ozone, be sure to locate this machine in a large well ventilated
room that has an air turnover of
more than 30 m3/hr/person.
144
Moving
R CAUTION:
• Unplug the power cord from the
wall outlet before you move the
machine. While moving the machine, you should take care that
the power cord will not be damaged under the machine.
Important
❒ Be careful when moving the machine. Take the following precautions:
• Turn off the main power. See
p.28 “Turning Off the Main
Power”.
• Unplug the power cord from
the wall outlet. When you pull
out the plug from the socket,
grip the plug to avoid damaging the cord, thereby reducing
the risk of fire or electric shock.
ThemisC1_EN_zentai_pre_FM.book Page 145 Thursday, June 30, 2005 8:21 PM
Where to Put Your Machine
• Close all covers and trays, including the front cover and bypass tray.
❒ Move the machine carefully. If you
do not, it could result in damage
and stored files might be lost.
❒ Do not take off the holding stand.
❒ Protect the machine from strong
shocks. Impact can damage the
hard disk and cause stored files to
be lost. As a precautionary measure, files should be copied to another computer.
Power Connection
R WARNING:
• Connect the machine only to
the power source described
on the inside front cover of
this manual. Connect the power cord directly into a wall outlet and do not use an
extension cord.
• Do not damage, break or make
any modifications to the power cord. Do not place heavy
objects on it. Do not pull it
hard nor bend it more than
necessary. These actions
could cause an electric shock
or fire.
R CAUTION:
• Unplug the power cord from the
wall outlet before you move the
machine. While moving the machine, you should take care that
the power cord will not be damaged under the machine.
R CAUTION:
• When you disconnect the power
plug from the wall outlet, always
pull the plug (not the cable).
• When the main power switch is in
the stand-by position, the optional
anti-condensation heaters are on.
In an emergency, unplug the machine's power cord.
• When you unplug the power cord,
the optional anti-condensation
heaters turn off.
• Make sure the plug is inserted
firmly in the wall outlet.
• Voltage must not fluctuate by
more than 10%.
• The wall outlet shall be installed
near the machine and shall be easily accessible.
Access to the Machine
Place the machine near the power
source, providing the clearance areas
shown.
7
AAE004S
1. Rear: more than 10 cm (4")
2. Right: more than 55 cm (21.7")
3. Front: more than 75 cm (29.6")
4. Left: more than 10 cm (4")
Note
❒ For the required space when options are installed, contact your
service representative.
145
ThemisC1_EN_zentai_pre_FM.book Page 146 Thursday, June 30, 2005 8:21 PM
Remarks
Maintaining Your Machine
If the exposure glass or ADF is dirty,
copy clarity may be reduced. Clean
these parts if they are dirty.
Cleaning the ADF
❖ Cleaning the machine
Wipe the ADF with a soft dry
cloth. If stains remain, wipe with a
well-wrung wet cloth, and then
wipe the water off with a dry cloth.
If the stains cannot be removed
with water, use a neutral detergent.
Important
❒ Do not use chemical cleaners or organic solvents, such as thinner or
benzene. If such substances get inside the machine or melt plastic
parts, a failure might occur.
❒ Do not clean parts other than those
explicitly specified in this manual.
Other parts should be cleaned only
by your service representative.
7
Cleaning the Exposure Glass
ZGJS827E
Clean 1 and 2.
Cleaning the Guide Boards
R CAUTION:
• The inside of the machine becomes very hot. Do not touch the
parts with a label indicating "v"
(means hot surface). Touching
"v" (means hot surface) could
result in a burn.
A Turn off the main power switch.
B Open the Bypass Tray.
ZGGH420E
Clean 1 and 2.
AFS032S
146
ThemisC1_EN_zentai_pre_FM.book Page 147 Thursday, June 30, 2005 8:21 PM
Maintaining Your Machine
Note
❒ Remove the paper on the Bypass Tray to prevent them from
falling.
C Open the Duplex Unit by push-
E Wipe the guide boards with a dry
cloth.
The guide boards are installed as
shown in the illustration.
ing the catch upwards. Open the
Duplex Unit by pushing the catch
upwards.
AFS037S
Important
❒ Do not use alcohol or detergent.
AFS033S
D Open the right cover of the printer by pushing up the handle.
F Close the right cover of the printer.
Note
❒ Press "PUSH" to close the cover
firmly.
7
G Close the Duplex Unit.
H Close the Bypass Tray.
I Turn on the main power switch.
AFS034S
Important
❒ Do not touch the inside of the
printer as it may cause an injury.
Cleaning and Adjusting
Internal Parts
Perform the following procedure
when missing colors and lines appear
on copies and prints.
A Press the {User Tools/Counter}} key
and then [Maintenance].
B Press [Clean / Adjust].
147
ThemisC1_EN_zentai_pre_FM.book Page 148 Thursday, June 30, 2005 8:21 PM
Remarks
C Press [Yes].
E Close the front cover of the machine.
Note
❒ Cleaning may take a while.
F Turn on the power switch.
❒ Do not open the cover or turn
off the power while the following display is shown and the
machine is cleaning.
D The display will return to [Maintenance] automatically when cleaning is finished. Press the { User
Tools/Counter}
} key and exit User
Tools.
Cleaning the Dustproof Glass
The dustproof glass may require
cleaning if white lines appear on the
print side of the document.
A Turn off the power switch.
B Open the front cover and remove
7
the cleaning brush.
C Slide the cleaning brush with the
blue handle in and out, slowly 8
to 10 times.
ZGJS707E
Important
❒ Do not insert the brush forcefully, or the machine might be
damaged.
D Return the cleaning brush to its
original position.
148
ThemisC1_EN_zentai_pre_FM.book Page 149 Thursday, June 30, 2005 8:21 PM
Other Functions
Other Functions
To display the [Inquiry] settings, the
machine must be configured. If you
want to display the settings, contact
your sales or service representative.
Printing inquiry information
A Press [Print Inquiry List].
Inquiry
The inquiry function lets you check
the telephone numbers to contact for
repairs or ordering toner. Be sure to
contact your service engineer to verify the following:
❖ Consumables
• Telephone No. to order
• Toner
• Staple
• TX Stamp Name
❖ Machine Maintenance/Repair
• Telephone No.
• Serial No. of Machine
❖ Sales Representative
• Telephone No.
A Press the {User Tools/Counter}} key.
B Press [Inquiry].
Inquiry information appears.
B Press the {Start}
} key.
Inquiry information is printed.
C Press [Exit].
D Press [Exit].
Changing the Display
Language
You can change the language used on
the display. English is set as default.
You can configure the machine to display the settings in Spanish. If you
want to display the settings in another language, contact your sales or
service representative.
7
A Press the {User Tools/Counter}} key.
B Press [Español].
The language is changed to Spanish.
C Press [Salir].
The menu appears in Spanish.
149
ThemisC1_EN_zentai_pre_FM.book Page 150 Thursday, June 30, 2005 8:21 PM
Remarks
Changing Paper Thickness
Settings
Select [Normal] or [Middle Thick/90105g/m 2 ] depending on the type of
plain paper.
Note
❒ Settings will not be cleared even
when the { Clear Modes}
} key is
pressed or the power is turned off.
❒ All paper trays are set to [Normal]
as default.
A Press the {User Tools / Counter}} key.
B Press [Maintenance].
7
C Press [Plain Paper Type].
D Select the plain paper
type for
each tray depending on the paper
to be set and press [OK].
Note
❒ When printing on paper thicker
than 90 g/m2(24 lb.), select [Middle Thick/90-105g/m2].
E Press [Exit].
150
ThemisC1_EN_zentai_pre_FM.book Page 151 Thursday, June 30, 2005 8:21 PM
Counter
Counter
To display the total counter, the machine must be configured. If you want
to display the settings, contact your
sales or service representative.
Displaying the Total Counter
You can display the total counter value used for all functions.
A Press the {User Tools/Counter}} key.
B Press [Counter].
7
C To print a counter list, press [Print
Counter List].
D Press the {Start}} key.
A counter list prints out.
151
ThemisC1_EN_zentai_pre_FM.book Page 152 Thursday, June 30, 2005 8:21 PM
Remarks
7
152
ThemisC1_EN_zentai_pre_FM.book Page 153 Thursday, June 30, 2005 8:21 PM
8. Entering Text
Entering Text
This section describes how to enter characters. When you enter a character, it appears at the position of the cursor. If there is a character already at the cursor position, the entered character appears before it.
Available Characters
• Alphabetic characters
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz
• Symbols
• Numerals
0123456789
Keys
ZHWS030E
Note
❒ When entering uppercase or lowercase letters continuously, use [Shift Lock] to
lock the case.
153
ThemisC1_EN_zentai_pre_FM.book Page 154 Thursday, June 30, 2005 8:21 PM
Entering Text
How to Enter Text
Entering letters
A Press [Shift] to switch between uppercase and lowercase.
B Press the letters you want to enter.
Deleting characters
A Press [Backspace] or [Delete All] to delete characters.
8
154
ThemisC1_EN_zentai_pre_FM.book Page 155 Thursday, June 30, 2005 8:21 PM
9. Specifications
Mainframe
❖ Configuration:
Desktop
❖ Photosensitivity type:
OPC belt
❖ Original scanning:
One-dimensional solid scanning system through CCD
❖ Copy process:
2 laser beam & dry electrostatic transfer system
❖ Development:
Mono component system
❖ Fusing:
Belt fusing system
❖ Resolution:
600 dpi
❖ Exposure glass:
Stationary original exposure type
❖ Original reference position:
Rear left corner
❖ Warm-up time:
99 seconds or less (23 °C, 73°F)
❖ Originals:
Sheet/book/objects
❖ Maximum original size:
A3L, 11" × 17"L
155
ThemisC1_EN_zentai_pre_FM.book Page 156 Thursday, June 30, 2005 8:21 PM
Specifications
❖ Copy paper size:
• Trays: A3L– A6L, 11" × 17"L – 51/2" × 81/2"KL
• Bypass: A3L– A6L, 12" × 18"L – 51/2" × 81/2"KL
• Tray 1, 2 (custom size):
Vertical: 100 – 297mm, 3.94" – 11.69"
Horizontal: 148 – 432mm, 5.83" – 17.00"
• Bypass (custom size):
Vertical: 90.0 – 305.0 mm, 3.55" – 12.00"
Horizontal: 148.0 – 457.2mm, 5.83" – 18.00"
• Duplex: A3L– A5KL, 11" × 17"L – 51/2" × 81/2"L (except, 51/2" × 81/2" K)
• LCT: A4K, 81/2" × 11"K
❖ Paper weight:
• Tray 1, 2: 64 – 163g/m2, 17 – 43.6 lb.
• Bypass tray: 64 – 163g/m2, 17 – 43.6 lb.
• Duplex: 60 – 105 g/m2, 16 – 28 lb.
❖ Non-reproduction area:
• Leading edge: Less than 4 ± 2mm
• Trailing edge: Less than 2 ± 2mm/1.5mm
• Left edge: Less than 2 ± 2mm
• Right edge: Less than 2 ± 2mm
❖ First copy time:
9
Full Color
Standard mode
OHP/Thick mode *1
Auto Color Select
mode *1
18 seconds or less
25 seconds or less
20 seconds or less
7.8 seconds or less
16 seconds or less
9.8 seconds or less
(4 colors)
Black, Yellow,
Magenta, Cyan
(A4K, 81/2" × 11K" , when setting an original on the exposure glass and full
size copying fed from Tray 1.)
*1
When you use the bypass tray, it takes a few more seconds.
❖ Copying speed (Full Color)
Standard mode
Thick mode
OHP mode
A4K, 8 /2" × 11"K
10 copies/minute
4 copies/minute
2 copies/minute
A3L, 11" × 17"L
5 copies/minute
2 copies/minute
1 copies/minute
1
(When copying continuously in full size.)
156
ThemisC1_EN_zentai_pre_FM.book Page 157 Thursday, June 30, 2005 8:21 PM
Mainframe
❖ Black, Yellow, Magenta, Cyan
Standard mode
Thick mode
OHP mode
6.5 copies/minute
3.2 copies/minute
3.2 copies/minute
1.6 copies/minute
A4K,
81/2" ×
11"K
Type 1
24 copies/minute
Type 2
32 copies/minute
A3L,
11" ×
17"L
Type 1
12 copies/minute
Type 2
16 copies/minute
(When copying continuously in full size.)
❖ Reproduction ratio:
Preset reproduction ratios:
Metric version
Enlargement
Inch version
400%
400%
200%
200%
141%
155%
122%
129%
115%
121%
Full size
100%
100%
Reduction
93%
93%
82%
85%
75%
78%
71%
73%
65%
65%
50%
50%
25%
25%
9
Zoom: From 25 to 400% in increments of 1%.
❖ Maximum continuous copy run:
100 sheets
❖ Paper capacity:
• Tray 1, 2: 250 sheets ( 80 g/m2, 20 lb.)
• Bypass tray: 100 sheets (80 g/m2, 20 lb.)
157
ThemisC1_EN_zentai_pre_FM.book Page 158 Thursday, June 30, 2005 8:21 PM
Specifications
❖ Power consumption:
• Mainframe only
Type 1/Type 2
Warm-up
less than 1.44 kW
Stand-by
less than 200 W
During printing
less than 1.2 kW
Maximum
• Complete system
less than 1.44 kW
*1
Type 1/Type 2
Warm-up
less than 1.44 kW
Stand-by
less than 200 W
During printing
less than 1.3 kW
Maximum
less than 1.44 kW
*1
The Complete System consists of the mainframe, 1000-sheet finisher, internal
tray 2, paper tray unit, fax unit, extra G3 interface unit, expansion memory,
JBIG function upgrade unit, printer unit, and memory unit.
❖ Dimensions (W × D × H up to exposure glass):
Type1,2 : 550 × 682 × 781 mm, 21.7" × 26.9" × 30.8"
❖ Space for main unit (W × D):
Type 1, 2 : 550 × 682mm, 21.7" × 26.9"
❖ Noise emission *1 :
Sound power level:
• Mainframe only
9
Type 1/Type 2
Stand-by
Less than 40 dB (A)
Copying
• Complete system
Less than 65 dB (A)
*2
Type 1/Type 2
158
Stand-by
Less than 40 dB (A)
Copying
Less than 70 dB (A)
ThemisC1_EN_zentai_pre_FM.book Page 159 Thursday, June 30, 2005 8:21 PM
Mainframe
Sound pressure level: *3
• Mainframe only
Type 1/Type 2
Stand-by
Less than 27dB(A)
Copying
• Complete system
Less than 52dB(A)
*2
Type 1/Type 2
*1
*2
*3
Stand-by
Less than 27dB(A)
Copying
Less than 57dB(A)
The above measurements made in accordance with ISO 7779 are actual value.
The Complete System consists of the mainframe, 1000-sheet finisher, internal tray
2 and paper tray unit.
Measured at the position of the bystander.
❖ Weight:
Types1,2: 85 kg, 187 lb.
❖ HDD:
about 40 GB
• Capacity for Document Server
about 15 GB
• Capacity for memory sorting
about 16 GB
• Capacity for others
about 9 GB
9
159
ThemisC1_EN_zentai_pre_FM.book Page 160 Thursday, June 30, 2005 8:21 PM
Specifications
ADF
❖ Mode:
ADF mode, Batch mode, SADF mode, Mixed Size mode, Custom Size originals mode
❖ Original size:
• A3L – A5KL
• 11" × 17"L – 51/2" × 81/2"KL
• Vertical: 105 – 297mm, 4.2" – 11.6"
• Horizontal: 128 – 1,200mm, 5.1" – 47.0"
(128 – 432mm, 5.1" – 17.0" for Copier and Scanner functions)
❖ Original weight:
• 1-sided originals: 40 – 128g/m2 (11 – 34 lb.)
• 2-sided originals: 52 – 105g/m2 (14 – 28 lb.) (Duplex)
❖ Maximum number of originals:
50 sheets (80g/m2, 20 lb.) or less than 11mm, 0.43"
❖ Maximum power consumption:
Less than 50W (power is supplied from the mainframe)
❖ Dimensions (W×
×D×
×H):
550 × 470 × 130mm, 21.7" × 18.5" × 5.1"
❖ Weight:
Approx. 10 kg, 22.1 lb.
9
Duplex Unit
❖ Paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5KL, 5 1/2" × 8 1/2"L, 7 1/4" × 10 1/2"L,
8 1/2" × 11"KL, 8" × 13"L, 8 1/2" × 13"L, 81/2" × 14"L, 8 1/4" × 13"L, 11" × 17"L,
8KL, 16KKL
❖ Paper weight:
64 – 105g/m2, 17 – 28 lb.
❖ Power consumption (Max):
35W (power is supplied from the mainframe)
❖ Dimensions (W × D × H):
121 × 479 × 510mm, 4.8" × 18.9" × 20.1"
160
❖ Weight:
Approx. 6kg, 13.3 lb.
ThemisC1_EN_zentai_pre_FM.book Page 161 Thursday, June 30, 2005 8:21 PM
Mainframe
Bypass Tray
❖ Paper size:
• Standard size: A3L – A6L, 12" × 18"L – 51/2" × 81/2"KL
• Custom size: Vertical (90.0 – 305.0mm, 3.55" – 12.00"), Horizontal (148.0 –
457.2mm, 5.83" – 18.00")
❖ Copy paper weight:
64 – 163g/m2, 17 – 43.6 lb.
❖ Dimensions (W × D × H):
310 × 380 × 275mm, 12.4" × 15.2" × 11"
❖ Paper capacity:
• 64 – 90g/m2, 17 – 20 lb: 100 sheets
❖ Weight:
Approx. 3kg, 6.6 lb.
9
161
ThemisC1_EN_zentai_pre_FM.book Page 162 Thursday, June 30, 2005 8:21 PM
Specifications
Options
Note
❒ Specifications are subject to change without notice.
500-Sheet Finisher
❖ Paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5K, 11" × 17"L, 8 1/ 2" × 14"L,
81/2" × 11"KL, 81/2" × 13"L, 71/4" × 101/2"L, 8KL, 16KK
❖ Paper weight:
64 – 128g/m2, 17 – 34 lb.
❖ Stack capacity:
• 500 sheets (A4KL, 81/2" × 11"KL or smaller) (80g/m2, 20 lb.)
• 250 sheets (B4 JISL, 8" × 13"L or larger) (80g/m2, 20 lb.)
❖ Staple capacity:
• 30 sheets (80g/m2, 20 lb.)
❖ Staple paper size:
A3L, B4 JISL, A4KL, B5 JISK, 11" × 17"L, 81/2" × 14"L, 81/2" × 13"L,
81/2" × 11"KL, 8KL, 16KK
❖ Staple paper weight:
64 – 128g/m2, 17 – 34 lb.
9
❖ Staple position:
1 position (top left)
❖ Power consumption:
40W (power is supplied from the mainframe)
❖ Dimensions (W × D × H):
350 × 490 × 230mm, 13.8" × 19.3" × 9.1"
❖ Weight:
Approx. 10kg, 22.1 lb.
162
ThemisC1_EN_zentai_pre_FM.book Page 163 Thursday, June 30, 2005 8:21 PM
Options
1000-Sheet Finisher
Finisher Proof Tray :
❖ Paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5KL, B6 JISL, A6L, 12" × 18"L,
11" × 17"L, 81/2" × 14"L, 101/2" × 71/4"KL, 81/2" × 13"L, 81/2" × 11"KL,
8" × 13"L, 81/4" × 13"L, 51/2" × 81/2"KL, 8KL, 16KKL
❖ Paper weight:
64 – 163g/m2, 17.0 – 43.6 lb.
❖ Stack capacity:
• 250 sheets (A4KL, 81/2" × 11"KL or smaller) (80g/m2, 20 lb.)
• 50 sheets (B4 JISL, 8" × 13"L or larger) (80g/m2, 20 lb.)
Finisher Shift Tray :
❖ Paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5KL, 81/2" × 11"KL, 11" × 17"L,
81/2" × 14"L, 101/2" × 71/4"KL, 8" × 13"L, 81/4" × 13"L, 81/2" × 13"L,
51/2" × 81/2" KL,12" × 18"L 8KL, 16KKL
❖ Paper weight:
64 – 163g/m2, 17.0 – 43.6 lb.
❖ Stack capacity:
• 1,000 sheets (A4KL, 81/2" × 11"KL or smaller) (80g/m2, 20 lb.)
• 500 sheets (B4 JISL, 8" × 13"L or larger) (80g/m2, 20 lb.)
9
❖ Staple capacity:
• 50 sheets (A4KL, 81/2" × 11"KL or smaller) (80g/m2, 20 lb.)
• 30 sheets (B4 JISL, 8" × 13"L or larger) (80g/m2, 20 lb.)
❖ Staple paper size:
A3L, B4 JISL, A4KL, B5 JISKL, 12" × 18"L, 11" × 17"L, 81/2" × 14"L,
81/2" × 11"KL, 101/2" × 71/4"KL, 8" × 13"L, 81/2" × 13"L, 81/4" × 13"L,
8KL, 16KKL
❖ Staple paper weight:
64 – 90g/m2, 17 – 24 lb.
❖ Staple position:
• 1 staple – 2 positions (top left, bottom left)
• 2 staples – 2 positions (left)
163
ThemisC1_EN_zentai_pre_FM.book Page 164 Thursday, June 30, 2005 8:21 PM
Specifications
❖ Power consumption:
Less than 50W (power is supplied from the mainframe)
❖ Dimensions (W × D × H):
527 × 520 × 790mm, 20.7" × 20.5" × 31.1"
❖ Weight:
Approx. 25kg, 55.2 lb.
Bridge Unit
❖ Paper Size:
• Internal tray: A3L – A6L, 12" × 18"L – 51/2" × 81/2"L
• 500-Sheet Finisher: A3L – A5K, 11" × 17"L – 51/2" × 81/2"L
• 1000-Sheet Finisher: A3L – A5KL, 12" × 18"L – 51/2" × 81/2"KL
❖ Paper weight:
64 – 163g/m2, 17.0 – 43.6 lb.
❖ Stack Capacity:
250 sheets
❖ Dimensions:
418 × 446 × 128mm, 16.47" × 17.57" × 50.40"
❖ Weight:
3.3kg, 7.29 lb.
Shift Sort Tray
9
❖ Paper capacity:
250 sheets (A4KL, 81/2" × 11"KL or smaller) (80g/m2, 20 lb.)
125 sheets (B4 JISL, 8" × 13"L or larger) (80g/m2, 20 lb.)
❖ Power consumption:
3.6 W (power is supplied from the mainframe)
❖ Dimensions (W × D × H)
430 × 372 × 148 mm, 17" × 15" × 6"
❖ Weight:
Approx. 1.6kg, 3.5 lb.
164
ThemisC1_EN_zentai_pre_FM.book Page 165 Thursday, June 30, 2005 8:21 PM
Options
Internal tray 2 (1 bin tray)
❖ Number of bins:
1
❖ Available paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5KL, B6 JISL, A6L, 11" × 17"L,
81/2" × 14"L, 81/2" × 11"KL, 101/2" × 71/4" KL, 8" × 13"L, 81/2" × 13"L,
81/4" × 13"L, 51/2" × 81/2" KL, 8KL, 16KKL, 37/8" × 71/2"K, 41/8" × 91/2"K,
C5 EnvK, C6 EnvK, DL EnvK
❖ Paper capacity:
125 sheets (80g/m2, 20 lb.)
❖ Copy paper weight:
64 – 105g/m2 (17 – 28 lb.)
❖ Maximum power consumption:
Less than 0.5 W (power is supplied from the mainframe)
❖ Dimensions (W × D × H):
530 × 435 × 120mm, 20.9" × 17.1" × 4.7"
❖ Weight:
Approx. 1.1 kg, 2.5 lb.
Large Capacity Tray (LCT)
❖ Paper size:
A4K, 81/2" × 11"K
9
❖ Paper weight:
64 – 105g/m2, 17 – 28 lb.
❖ Paper capacity:
2,000 sheets (80g/m2, 20 lb.)
❖ Power consumption
Maximum. 30 W (power is supplied from the mainframe)
❖ Dimensions (W × D × H, option unit):
540 × 600 × 270mm, 21.3" × 23.6" × 10.6"
❖ Weight:
Approx. 25 kg, 55 lb.
165
ThemisC1_EN_zentai_pre_FM.book Page 166 Thursday, June 30, 2005 8:21 PM
Specifications
Paper tray unit
❖ Copy paper weight:
64 – 128g/m2 (17 – 34 lb.)
❖ Available paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5KL, 11" × 17"L, 81/ 2" × 14"L,
81/2" × 13"L, 81/ 2" × 11"KL, 81/ 4" × 13"L, 8" × 13"L, 71/4" × 10 1/2"L,
51/2" × 81/2"KL, 8KL, 16KKL
❖ Maximum power consumption:
Less than 30 W (power is supplied from the mainframe)
❖ Paper capacity:
500 sheets (80g/m2, 20 lb.) × 2 trays
❖ Dimensions (W × D × H):
540 × 600 × 270mm, 21.3" × 23.6" × 10.6"
❖ Weight:
Approx. 25 kg, 55.2 lb.
9
166
ThemisC1_EN_zentai_pre_FM.book Page 167 Thursday, June 30, 2005 8:21 PM
Copy Paper
Copy Paper
Recommended Paper Sizes and Types
The following limitations apply to each tray:
Tray
Type
Paper Type and
Weight
Tray 1, 2 64-105g/m2
(17-28 lb.)
Metric Version
Inch Version
Paper
Capacity
A3L, B4 JISL, A4KL,
B5 JISKL, A5K,
81/2" × 11"L
A4L, B5 JISKL,
11" × 17"L, 81/2" × 14"L,
81/2" × 11"KL
250 sheets
*1
A5L, A6L, 11" × 17"L,
81/2" × 14"L, 81/2" × 11"K,
51/2" × 81/2"KL,
71/4" × 101/2"KL,
8" × 13"L, 81/2" × 13"L,
81/4" × 13"L, 8KL, 16KKL
*1
A3L, B4 JISL, A4K,
A5KL, A6L,
51/2" × 81/2"KL,
71/4" × 101/2"KL,
8" × 13"L, 81/2" × 13"L,
81/4" × 13"L, 8KL, 16KKL
*2
Custom size
*2
Custom size
Vertical: 100.0-297.0 mm Vertical: 3.94"-11.69"
Horizontal: 148.0-432.0 mm Horizontal: 5.83"-17.00"
Thick paper
*8
2
106-163g/m
(28.3-43.6 lb.)
A3L, B4 JISL, A4KL,
B5 JISKL, A5K,
81/2" × 11"L
A4L, B5 JISKL,
11" × 17"L, 81/2" × 14"L,
81/2" × 11"KL
*1
A5L, A6L, 11" × 17"L,
81/2" × 14"L, 81/2" × 11"K,
51/2" × 81/2"KL,
71/4" × 101/2"KL,
8" × 13"L, 81/2" × 13"L,
81/4" × 13"L, 8KL, 16KKL
*1
A3L, B4 JISL, A4K,
A5KL, A6L,
51/2" × 81/2"KL,
71/4" × 101/2"KL,
8" × 13"L, 81/2" × 13"L,
81/4" × 13"L, 8KL, 16KKL
*2
Custom size
*2
50 sheets
9
Custom size
Vertical: 100.0-297.0 mm Vertical: 3.94"-11.69"
Horizontal: 148.0-432.0 mm Horizontal: 5.83"-17.00"
OHP transparencies A4K *1
20 sheets
*8
167
ThemisC1_EN_zentai_pre_FM.book Page 168 Thursday, June 30, 2005 8:21 PM
Specifications
Tray
Type
Paper Type and
Weight
Paper
64 - 105g/m2
tray
(17-28 lb.)
unit
(option)
Metric Version
Inch Version
Paper
Capacity
A3L, B4 JISL, A4KL,
B5 JISK, A5K, 11" × 17"L,
81/2" × 11"K
A3L, A4K, 11" × 17"L,
81/2" × 14"L, 81/2" ×
11"KL, 81/2" × 51/2"K
500 sheets
×2
*1
B5 JISL, A5L,
81/2" × 14"L, 81/2" × 11"L,
51/2" × 81/2"KL,
71/4" × 101/2"L, 8" × 13"L,
81/2" × 13"L, 81/4" × 13"L,
8KL, 16KKL
*1
B4 JISL, A4L,
B5 JISKL, A5KL,
51/2" × 81/2"L,
71/4" × 101/2"L, 8" × 13"L,
81/2" × 13"L, 81/4" × 13"L,
8KL, 16KKL
*2
Custom size
*2
Custom size
Vertical: 148.0 - 297.0 mm Vertical: 5.83" - 11.69"
Horizontal: 148.0 - 432.0 mm Horizontal: 5.83" - 17.00"
9
168
ThemisC1_EN_zentai_pre_FM.book Page 169 Thursday, June 30, 2005 8:21 PM
Copy Paper
Tray
Type
Paper Type and
Weight
Metric Version
Inch Version
Paper
Capacity
Bypass
Tray
64-105g/m2
(17-28 lb.)
A3L, A4L, 8" × 13"L,
A5L
11" × 17"L, 81/2" × 11"L,
51/2" × 81/2"L
100 sheets
*3 B4 JISL, A4K,
B5 JISKL, A5K, B6 JISL,
A6L, 11" × 17"L,
81/2" × 14"L,
81/2" × 11"KL,
51/2" × 81/2"KL,
71/4" × 101/2"KL,
81/2" × 13"L, 81/4" × 13"L,
12" × 18"L, 8KL, 16KKL
*3 A3L, B4 JISL, A4KL,
B5 JISKL, A5KL,
B6 JISL, A6L,
81/2" × 14"L, 81/2" × 11"K,
81/2" × 51/2"K,
71/4" × 101/2"KL,
8" × 13"L, 81/2" × 13"L,
81/4" × 13"L, 12" × 18"L,
8KL, 16KKL
*4
Custom size
Vertical: 90.0-305.0 mm
*4
Custom size
Vertical: 3.55"-12.00"
Horizontal: 148.0-457.2 mm Horizontal: 5.83"-18.00"
Thick paper
*9
106-163g/m2
(28.3-43.6 lb.)
A3L, A4L, 8" × 13"L,
A5L
11" × 17"L, 81/2" × 14"L, 30 sheets
81/2" × 11"L, 51/2" × 81/2"L
*3
B4 JISL, A4K,
B5 JISKL, A5K, B6 JISL,
A6L, 11" × 17"L,
81/2" × 14"L,
81/2" × 11"KL,
51/2" × 81/2"KL,
71/4" × 101/2"KL,
81/2" × 13"L, 81/4" × 13"L,
12" × 18"L, 8KL, 16KKL
*3
A3L, B4 JISL,
A4KL, B5 JISKL,
A5KL, B6 JISL, A6L,
81/2" × 14"L, 81/2" × 11"K,
81/2" × 51/2"K,
71/4" × 101/2"KL,
8" × 13"L, 81/2" × 13"L,
81/4" × 13"L, 12" × 18"L,
8KL, 16KKL
*4
Custom size
Vertical: 90.0-305.0 mm
*4
Custom size
9
Vertical: 3.55"-12.00"
Horizontal: 148.0-457.2 mm Horizontal: 5.83"-18.00"
Translucent paper
A3L, A4KL
*7
OHP transparencies
A4K *3
*9
*2
50 sheets
*5
Label paper
(adhesive labels)
B4L, A4KL
1 sheet
Envelope *3
37/8" × 71/2"K, 41/8" × 91/2"K, C5 EnvK, C6 EnvK, DL EnvK
–
A4K, 81/2" × 11"K *6
2000
(1000 +
1000)
sheets
Large
64-105g/m2
Capaci- (17-28 lb.)
ty Tray
(LCT)
(option)
*1
50 sheets
*5
Select the paper size in System Settings. ⇒ p.58 “Tray Paper Size: (Tray 1-4)”
Specify the paper size. ⇒ p.58 “Tray Paper Size: (Tray 1-4)”
169
ThemisC1_EN_zentai_pre_FM.book Page 170 Thursday, June 30, 2005 8:21 PM
Specifications
*3
*4
*5
*6
*7
*8
*9
Place the paper in the bypass tray, and select the paper size. ⇒ “Copying from the
Bypass Tray” in Copy Reference
Place the paper in the bypass tray, and specify the paper size. ⇒ “Copying from the
Bypass Tray” in Copy Reference
With paper longer than 457mm, misfeeds, jams and creasing is more likely. Make
sure paper is placed correctly so that it is fed straight.
It is recommended to place one sheet at a time.
The paper tray fence is immovable. If you wish to change the size of paper placed in
this tray, contact your service representative.
When loading translucent papers, set the paper direction along its recommendation.
Select the paper type in System Settings. ⇒ p.59 “Paper Type: Tray 1–4”
Select the paper type in System Settings. ⇒ p.59 “Paper Type: Bypass tray”, “Copying from the Bypass Tray” in Copy Reference
Important
❒ If you use damp or curled paper, a misfeed may occur.
Note
❒ When loading paper, make sure the stack height does not exceed the lower
limit mark of the paper tray. ⇒ p.114 “BLoading Paper”
❒ When loading copy paper in the paper tray 1-4 and the large capacity tray
(LCT), place the copy side of the paper face up.
❒ When printing on paper less than 90g/m2(24lb.), select [Normal] in the control
panel. When printing on paper between 90 to 105g/m2(24 to 28lb.), select [Middle Thick/90-105g/m2] in the control panel. ⇒ p.150 “Changing Paper Thickness
Settings”
❒ When using thick paper, the machine may produce a different sound.
❒ When loading copy paper in the bypass tray, place the copy side of the paper
face down.
❒ When you use the bypass tray, it is recommended to set the copy paper direction to L.
❒ When you load the OHP transparencies, check the front and back of the
sheets, and place them correctly, or a misfeed might occur. When using OHP
transparencies with a taped edge, set them so the taped edge is fed last. Set
the paper direction to K and select A4K, 81/2"×11"K as paper size, ⇒ p.58
“Tray Paper Size: (Tray 1-4)”, “Copying from the Bypass Tray” in Copy Reference.
❒ When you use OHP transparencies, shuffle them for each use. If you store the
sheets in the tray, they may adhere and may cause feeding problems.
❒ If multiple-sheet jams occur, load the paper sheet by sheet.
❒ Envelopes should be fed using the bypass tray.
9
❖ When copying onto envelopes
• Be sure to set the size of the envelope before copying. For details, see
“When Copying onto Envelopes” in the Copy Reference.
• If you are printing onto the envelope from the printer driver, set the size
of the envelope from the printer driver.
170
ThemisC1_EN_zentai_pre_FM.book Page 171 Thursday, June 30, 2005 8:21 PM
Copy Paper
• When you are copying or printing on envelopes, select “Thick Paper”
for the paper type.
• The minimum vertical length of envelopes that can be loaded is 140
mm, including opened flap.
• Do not print on both sides.
• Do not stack more than 10 envelopes in the output tray.
• Do not use double-flapped envelopes.
• Do not use envelopes with released tabs attached to the sealed part.
• Some kinds of envelopes might wrinkle or the print quality may be affected, especially on overlaps.
• Load envelopes bottom side first and flaps open.
• Before loading envelopes, flatten opened flaps.
❒ If you load paper of the same size in the same direction in two or more trays,
the machine automatically shifts to the other tray when the first tray in use
runs out of paper. This function is called Auto Tray Switching. (However, if
one tray has recycled or special paper, the settings of the other trays must be
the same for Auto Tray Switching.) This saves interrupting a copy run to replenish paper when making a large number of copies.
❒ The paper types you can select in System Settings are only general classifications. The copy quality for every kind of paper in a classification is not guaranteed. See ⇒ p.171 “Non-recommended Paper” for more information.
Non-recommended Paper
R CAUTION:
• Do not use aluminum foil, carbon paper, or similar conductive paper to avoid
a fire or machine failure.
9
Important
❒ To prevent faults, do not use any of the following kinds of paper:
• Papers for inkjet printers
• Thermal fax paper
• Art paper
• Aluminum foil
• Carbon paper
• Conductive paper
• Paper with perforated lines
• Hemmed-edge paper
❒ Do not copy onto a side that already has copy on, or a fault might occur.
❒ Do not use sheets with copies printed on them by another machine.
171
ThemisC1_EN_zentai_pre_FM.book Page 172 Thursday, June 30, 2005 8:21 PM
Specifications
Note
❒ To prevent misfeeds, do not use the following kinds of paper:
• Bent, folded, or creased paper
• Torn paper
• Slippery paper
• Perforated paper
• Rough paper
• Thin paper with little stiffness
• Paper with a dusty surface
❒ If you copy onto rough grain paper, the image might be blurred.
Paper Storage
Note
❒ When storing paper, the following precautions should always be followed:
• Do not store paper where it will be exposed to direct sunlight.
• Avoid storing paper in humid areas (humidity: 70% or less).
• Store on a flat surface.
❒ Do not store paper vertically.
❒ Under high temperature and humidity conditions, or low temperature and
humidity conditions, store paper in a vinyl bag.
9
172
ThemisC1_EN_zentai_pre_FM.book Page 173 Thursday, June 30, 2005 8:21 PM
INDEX
A
Adding a Group to Another Group, 99
Adding Staples, 131
Adding toner, 117
Address Book
Change Order, 66
Edit Title, 67
Program / Change / Delete Group, 65
Select Title, 68
Address book, 69
Address Book Management, 65
ADF, 19, 160
cleaning, 146
Adjust/Program Color key, 23
Administrator Authentication Management, 63
Administrator Tools, 63
AOF (Always On), 68
Authentication Information, 74
Auto color calibration, 138
Auto Delete File, 68
Auto Off, 29
Auto off timer, 61
Auto Reset Timer
printer, 62
Auto reset timer
copier/Document Server, 62
facsimile, 62
scanner, 62
system, 61
B
Browse network, 91
Bypass tray, 161
C
Changing a group name, 98
Changing a name Registered Name, 72
Changing a registered e-mail destination, 87
Changing a registered fax destination, 81
Changing a registered folder, 91, 94
Changing a Registered IP-Fax Destination, 84
Changing a registered
Transfer Station/Receiving Station, 105
Changing a user code, 75
Changing paper size of Tray 1 and 2, 126
Changing Paper Thickness Settings, 150
Changing the language, 149
Changing the paper size, 126
Check Modes key, 23
Cleaning the Dustproof Glass, 148
Clearing misfeeds, 121
Clearing the number of prints, 77
Clear Modes key, 24
Clear/Stop key, 24
Color circle, 23
Color selection keys, 24
Combined function operations, 31
Control panel, 19, 23
Copy Count Display, 55
Copy Paper, 167
Cover sheet tray, 60
D
Delete All Files, 68
Deleting a group, 99
Deleting a registered e-mail destination, 88
Deleting a registered fax destination, 82
Deleting a registered folder, 92, 95
Deleting a registered
Transfer Station/Receiving Station, 106
Deleting a user, 73
Deleting a user code, 75
Display / Clear / Print Counter per User, 64
Displaying names registered in groups, 97
Displaying the Counter for each user code, 76
Displaying the Total Counter, 151
Display panel, 23, 25
Display / Print Counter, 64
Document Server, 37
Deleting, 47
Downloading, 48
Printing, 44
Selecting, 42
Using the Document Server, 39
Viewing, 47
Do's and Don'ts, 141
Duplex unit, 160
E
Earth Leakage Breaker, 20
E-mail destination, 86
Energy Saver key, 24
Entering text, 153
Environment, 144
Exposure glass, 19
Extended Security, 64
External options, 21
173
ThemisC1_EN_zentai_pre_FM.book Page 174 Thursday, June 30, 2005 8:21 PM
F
Fax destination, 78
Firmware Version, 68
Front cover, 19
FTP, 93
Function keys, 24
Function Priority, 55
Function reset timer, 56
Function status indicators, 24
I
Indicators, 23
Inquiry, 149
Internal options, 22
Internal tray, 19
Internal tray 2 (1 bin tray) (optional), 19
Interrupt key, 24
K
# key, 24
Key Counter Management, 64
L
Large Capacity Tray (LCT), 165
Loading Paper
Large Capacity Tray, 115
Tray 3 and 4, 114
Loading paper, 114
paper size, 126
Tray 1 and 2, 114
M
Machine environment, 144
Mainframe, 155
Main power indicator, 24
Main power switch, 19, 27
Maintaining Your Machine, 146
Misfeeds, 121
Moving, 144
Multi-Access, 33
N
Number keys, 24
O
Operation switch, 24, 27
Options, 162
174
P
Panel off timer, 61
Panel Tone, 55
Paper
changing, 126
loading, 114
Paper tray, 19
Paper tray priority
copier, 58
facsimile, 58
printer, 58
Paper type
bypass tray, 59
tray 1–4, 59
Power connection, 145
Power indicator, 24
Print Address Book
Destination List, 67
Printing the Counter for each user code, 76
Print Priority, 55
Program / Change Administrator, 64
Program / Change / Delete LDAP Server, 68
Program key, 23
Protection
code, 101, 102
destination, 101
R
Receiving Station, 103
Registering a fax destination, 79
Registering a name, 72
Registering an e-mail destination, 86
Registering a New Group, 96
Registering a new user code, 74
Registering an IP-Fax Destination, 83
Registering a protection code, 101
Registering a protection code
to a group user, 102
Registering a protection code
to a single user, 101
Registering a Transfer Station/
Receiving Station, 103
Registering Authentication, 107
Registering Folders, 89
Registering Names, 72
Registering names to a group, 96, 97
Registering the Transfer Request, 103
Remarks, 141
Remove Paper Indicator, 19
Removing a name from a group, 98
Removing Jammed Staples, 134
ThemisC1_EN_zentai_pre_FM.book Page 175 Thursday, June 30, 2005 8:21 PM
S
Safety information, 12
Sample Copy key, 24
Saving Color Copies, 142
Saving energy, 29
Screen contrast knob, 23
Set date, 62
Set time, 62
Slip sheet tray, 60
SMB, 89
Specification
ADF, 160
Duplex unit, 160
Internal tray 2 (1 bin tray), 165
Large Capacity Tray (LCT), 165
Paper tray unit, 166
Shift Sort Tray, 164
Specifications, 155
mainframe, 155
Staples, 131
Removing Jammed Staples, 134
Start key, 24
System Reset, 32
T
Toner, 143
adding, 117
storage, 143
To register an FTP folder, 93
To register an SMB folder, 89
Transfer Station, 103
Tray paper size, 58
U
Use LDAP Server, 68
User Authentication Management, 63
User Tools/Counter key, 23
User Tools (System Settings), 51
Using FTP to Connect, 93
Using SMB to Connect, 89
W
Warm Up Notice (copier/Document Server), 55
Web browser, 47
175
ThemisC1_EN_zentai_pre_FM.book Page 176 Thursday, June 30, 2005 8:21 PM
MEMO
176
ThemisC1_EN_zentai_pre_FM.book Page 177 Thursday, June 30, 2005 8:21 PM
MEMO
177
ThemisC1_EN_zentai_pre_FM.book Page 178 Thursday, June 30, 2005 8:21 PM
MEMO
178
EN
USA
B156-7505B
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=188 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 7.520000 mm
Introduction
This manual contains detailed instructions and notes on the operation and use of this machine. For your
safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy
place for quick reference.
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a means POWER ON.
b means POWER OFF.
cmeans STAND BY.
For safe and correct use of this machine, please be sure to read the Safety Information before you use
it.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
Notes:
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Laser Safety:
CDRH Regulations
This equipment complies with requirements of 21 CFR Subchapter J for class 1 laser products. This
equipment contains two AlGalnP laser diodes, 7–milliwatt, 653–659 nanometer wavelength for each
emitter. This equipment does not emit hazardous light, since the beam is totally enclosed during all customer modes of operation and maintenance.
Caution:
Use of controls or adjustments or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Notes:
The model names of the machines do not appear in the following pages. Check the type of your machine before reading this manual. (For details, see P.18 “Machine Types”.)
•
Type 1: C2410/DSc424/LD124c/Aficio 3224C
•
Type 2: C3210e/DSc432/LD132c/Aficio 3232C
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the inch version.
For good copy quality, the supplier recommends that you use genuine toner from the supplier.
The supplier shall not be responsible for any damage or expense that might result from the use of parts
other than genuine parts from the supplier with your office products.
Power Source
120V, 60Hz, 12A or more
Please be sure to connect the power cord to a power source as shown above. For details about power
source, see P.145 “Power Connection”.
Copyright © 2005
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=188 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 7.520000 mm
Operating Instructions
General Settings Guide
Getting Started
Combined Function Operations
Document Server
User Tools (System Settings)
Registering Addresses and Users for Facsimile/Scanner Functions
Troubleshooting
Remarks
Entering Text
Specifications
Type for C2410/DSc424/LD124c/Aficio 3224C
Type for C3210e/DSc432/LD132c/Aficio 3232C
Printed in China
EN USA B156-7505B
B1567505B
Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety
Information in this manual before using the machine.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement