Christie E Series User manual

Christie E Series User manual
E Series
USER MANUAL
020-000287-01
NOTICES
COPYRIGHT AND TRADEMARKS
© 2011 Christie Digital Systems USA, Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of
their respective holders.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the product is operated in a commercial environment. The
product generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of the product in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at the user’s own expense.
WARNING! Changes or modifications not expressly approved by Christie could void the user’s
authority to operate the product.
FOR COMMERCIAL USE ONLY - POUR USAGE COMMERCIAL UNIQUEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING 2 CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
CET APPAREIL NUMÉRIQUE DE CLASSE A EST CONFORME AUX NORMES DÉFINIES
DANS LES RÉGLEMENTATIONS CANADIENNES SUR LES APPAREILS CAUSANT
DES INTERFÉRENCES RADIO (CANADIAN INTERFERENCE-CAUSING EQUIPMENT
REGULATIONS, ICES-003, CLASS A).
声明
此为A级产品,在生活环境中,该产品可能会造成无线干扰。在这种请况下,可能需要用
户对其干扰采取切实可行的措施。
이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의
하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다.
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products
or availability could occur which may not be reflected in this document. Christie reserves the right
to make changes to specifications at any time without notice. Performance specifications are
typical, but may vary depending on conditions beyond Christie's control such as maintenance of
the product in proper working conditions. Performance specifications are based on information
available at the time of printing. Christie makes no warranty of any kind with regard to this material,
including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not
be liable for errors contained herein or for incidental or consequential damages in connection with
the performance or use of this material.
The product is designed and manufactured with high-quality materials and components that can
be recycled and reused. This symbol
means that electrical and electronic equipment, at their
end-of-life, should be disposed of separately from regular waste. Please dispose of the product
appropriately and according to local regulations. In the European Union, there are separate
collection systems for used electrical and electronic products. Please help us to conserve the
environment we live in!
Canadian manufacturing facility is ISO 9001 and 14001 certified.
GENERAL WARRANTY STATEMENTS
For complete information about Christie’s limited warranty, please contact your Christie dealer. In
addition to the other limitations that may be specified in Christie’s limited warranty, the warranty
does not cover:
a.
b.
c.
d.
e.
f.
g.
h.
Damage occurring during shipment, in either direction.
Projector lamps (See Christie’s separate lamp program policy).
Damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp
supplied by a supplier other than Christie.
Problems caused by combination of the product with non-Christie equipment, such as distribution
systems, cameras, video tape recorders, etc., or use of the product with any non-Christie interface
device.
Damage caused by misuse, improper power source, accident, fire, flood, lightening, earthquake or
other natural disaster.
Damage caused by improper installation/alignment, or by product modification, if by other than a
Christie authorized repair service provider.
For LCD projectors, the warranty period specified applies only where the LCD projector is in “normal
use.” “Normal use” means the LCD projector is not used more than 8 hours a day, 5 days a week.
For any LCD projector where “normal use” is exceeded, warranty coverage under this warranty
terminates after 6000 hours of operation.
Failure due to normal wear and tear.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your
product. Please see the Maintenance section for specific maintenance items as they relate to your
product. Failure to perform maintenance as required, and in accordance with the maintenance
schedule specified by Christie, will void the warranty.
Table of Contents
1. SAFETY
1.1 Precautions....................................................................................................................1-1
1.2 Do..................................................................................................................................1-2
1.3 Do not............................................................................................................................1-2
2. INTRODUCTION
2.1 Projector Overview........................................................................................................2-1
2.1.1 Main Unit............................................................................................................2-1
2.1.2 Built-in Keypad...................................................................................................2-3
2.1.3 Input/Output (I/O) Panel.....................................................................................2-4
2.1.4 Remote Control..................................................................................................2-5
2.1.5 LED Indication Chart..........................................................................................2-7
2.2 Key Features.................................................................................................................2-9
2.3 List of Components........................................................................................................2-10
3. INSTALLATION
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
Connecting to Computer................................................................................................3-1
Connecting to Video Equipment....................................................................................3-2
Powering the Projector ON............................................................................................3-3
Powering the Projector OFF..........................................................................................3-3
Adjusting the Projector Position.....................................................................................3-4
Lamp Installation...........................................................................................................3-9
Lens Installation.............................................................................................................3-10
Ceiling Mount Installation..............................................................................................3-11
4. OPERATION
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
Using the On-Screen Display Menus............................................................................4-1
Size & Position Menu....................................................................................................4-2
Image Settings Menu.....................................................................................................4-4
Configuration Menu.......................................................................................................4-6
Lamp Menu....................................................................................................................4-9
Status Menu..................................................................................................................4-10
Input Switching & PIP Menu..........................................................................................4-11
Language.......................................................................................................................4-13
Test Pattern...................................................................................................................4-13
5. APPENDICES
5.1
5.2
5.3
5.4
5.5
Troubleshooting.............................................................................................................5-1
Input Specification.........................................................................................................5-4
PIP/PBP Compatibility...................................................................................................5-5
Declaration of Conformity for EU Countries..................................................................5-6
Federal Communications Commission (FCC) Warning.................................................5-6
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 1: Safety
1.
SAFETY
1.1
Precautions
Installers, service trained operators and all other users must maintain a safe
operating environment at all times. Read through this document in its entirety
and understand all warnings and precautions before attempting to operate this
projector.

WARNING
Do not look into the projector lens when the lamp is on. The bright light
may result in permanent eye damage.

To reduce the risk of fire or electric shock, do not expose this projector to
rain or moisture.

Do not open or disassemble the projector as this may cause electric shock.

When replacing the lamp, allow the unit to cool down, and follow all
replacement instructions.

This projector will detect the life of the lamp. Make sure the lamp is
changed when a warning message is displayed.

When you switch the projector OFF, ensure that the cooling cycle is
complete before disconnecting the power. Allow 90 seconds for the
projector to cool down.

Cooling of the lamp during the ignition phase should be avoided. This may
lead to ignition failures. After a successful lamp ignition, keep the lamp
burning for at least 15 minutes to maintain lamp life.

When the lamp is approaching the end of its life, the message “Lamp is
approaching the end of its useful life in full power operation” appears on
the screen. Contact your local reseller or service center to change the
lamp as soon as possible.

All installation and maintenance procedures must be performed by a
Christie accredited service technician.

FIRE HAZARD. Keep hands, clothes and all combustible material away
from the concentrated light beam of the projector. Position all cables where
they cannot contact hot surfaces or be pulled or tripped over.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
1-1
Section 1: Safety
1.2
1.3
1-2
Do

Always power down the projector and disconnect all power sources before
servicing or cleaning.

Use a soft cloth moistened with a mild detergent to clean the display
housing.

Disconnect the power plug from the AC outlet if the product is not being
used for an extended period of time.

Operate the projector under the following conditions:
-
Operating temperature range: 5°C to 35°C
-
Storage temperature range: -10°C to 60°C
-
Humidity range: 5% to 80 % RH (Max.), non condensing
-
Operating altitude: 10,000 ft. maximum

Use only the AC power cord supplied. Do not attempt operation if the AC
supply and cord are not within the specified voltage and power range.

Remove the lens plug from the lens opening in the projector before
installing the lens. Retain the lens plug for projector transportation to
protect the optical components from dust and debris.
Do not

Do not block the ventilation slots and openings on the unit.

Do not use abrasive cleaners, waxes or solvents to clean the unit.

Do not look into the lens.

Do not allow anything to rest on the power cord.

Do not attempt to access the lamp while the lamp is ON. After turning the
lamp OFF, it is critical that you wait at least 10 minutes before handling
the lamp. This provides sufficient time for the lamp cooling fans to properly
cool the lamp.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 2: Introduction
2.
INTRODUCTION
2.1
Projector Overview
The product specified in this document is a high brightness, high-resolution
video/graphics 1-chip mercury lamp based projector. The projector is available
in HD and WUXGA resolutions. The projector utilizes Digital Light Processing
(DLP®) technology from Texas Instruments. It is primarily designed for fixed
installation markets.
2.1.1 Main Unit
Front View
1
2
3
4
5
Rear View
6
7
8
9
USB
RS232 IN
Ethernet
VGA-OUT
Wired Keypad
DC5V
DC12V
SVID
CVBS
Green/Y
Blue/Pb
Red/Pr
2-HDMI
R
G
10
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
1-VGA
2-VGA
1-HDMI
B
H/C
V
2-1
Section 2: Introduction
Ind.
Description
Lens door
The lens door is located on the top-front of the
projector, which provides easy access to the lens
module for replacement.
2
Front IR Sensor
The front IR sensor, located next to the nameplate,
is used to receive signals from the IR remote. It
is important to keep the signal path to the sensor
unobstructed for uninterrupted communication with the
projector.
3
Projection Lens
The projector includes a motorized lens mount that
allows automated lens control and adjustment: vertical
and horizontal offsets, zoom and focus.
4
Cooling Air Vents
There are numerous air vents located around
the projector. It is important these vents remain
unobstructed. Adequate airflow through the projector
will prevent it from overheating.
5
Adjustable Feet
Four adjustable feet are located on the underside of the
projector. Raise or lower these feet when positioning
the projector to ensure it is level on all sides so the
displayed image appears rectangular without any
keystone.
6
The LED status indicators are located on the rear of the
LED Status Indicators projector. They are (from left to right): LAMP 1, LAMP 2,
STATUS, SHUTTER.
7
Rear IR Sensor
The rear IR sensor, located on the rear of the projector
between the LED status indicators, receives signals
from the IR remote. It is important to keep the signal
path to the sensor unobstructed for uninterrupted communication with the projector.
8
Lamp Door (Screws)
The lamp door is located on the top-rear of the
projector, which provides easy access to the lamp
module for replacement.
9
Built-in Keypad
The built-in keypad is located on the rear of the
projector. Use it similarly to the IR remote to control the
projector.
10
Input/Output (I/O)
Panel
All source connections are made to the I/O panel
located on the rear of the projector.
1
2-2
Part Name
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 2: Introduction
2.1.2 Built-in Keypad
1
6
2
7
3
8
4
9
5
10
Ind.
Key Name
Description
1
Power
Turn projector ON/OFF
2
Menu
Display menus
3
Auto
Automatically optimize image
4
Lens
Adjust the lens setting
5
Focus
Adjust focus
6
Exit
Return to previous level or exit menus if at top level
7
Arrow Keys
8
Input
Select an input for the main or PIP/PBP image
9
Shutter
OPEN or CLOSE the shutter
10
Zoom
Adjust zoom
E Series User Manual
020-000287-01 Rev. 1 (01-2011)

Adjust a setting UP or DOWN

Navigate within a menu
2-3
Section 2: Introduction
2.1.3 Input/Output (I/O) Panel
1
Ind.
2-4
2
3
4
5
6
7
8
9
10
Wired Keypad
DC5V
DC12V
SVID
CVBS
Green/Y
Blue/Pb
Red/Pr
USB
RS232 IN
Ethernet
VGA-OUT
1-VGA
2-VGA
1-HDMI
2-HDMI
R
G
B
H/C
V
11
12
13
14
15
16
17
18
19
20
21
Connector Name
Ind.
Connector Name
Ind.
Connector Name
1
USB
2
RS232 IN
3
Wired Keypad
4
DC5V
5
DC12V
6
SVID
7
CVBS
8
Green/Y
9
Blue/Pb
10
Red/Pr
11
Ethernet
12
VGA-OUT
13
1-VGA
14
2-VGA
15
1-HDMI
16
2-HDMI
17
R
18
G
19
B
20
H/C
21
V
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 2: Introduction
2.1.4 Remote Control
1. Power
17. Auto
2. Shutter
3. Number Keys
4. Help
5. Test
6. Menu
18. Hot-key
19. Info
20. Exit
21. Enter
7. Arrow Keys
8. Input
22. OSD
9. Bright
10. Contrast
11. Display
12. Gamma
23. Focus
24. Zoom
13. Keystone H
25. Lens H
14. Keystone V
26. Lens V
15. PIP/PBP
27. Swap
16. Size
28. Layout
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
2-5
Section 2: Introduction
Ind.
2-6
Key Name
Description
1
Power
Turn projector ON/OFF
2
Shutter
OPEN or CLOSE the shutter
3
Number Keys
Enter a number, such as a channel, value, etc.
4
Help
Display context-sensitive help
5
Test
Display a test pattern
6
Menu
Display menus
7
Arrow Keys
8
Input
Select an input for the main or PIP/PBP image
9
Bright
Adjust amount of light in the image
10
Contrast
Adjust difference between dark and light
11
Display
Select image preset
12
Gamma
Adjust mid-range levels
13
Keystone H
Adjust the horizontal keystone
14
Keystone V
Adjust the vertical keystone
15
PIP/PBP
Turn PIP/PBP ON/OFF
16
Size
Adjust the PIP/PBP size
17
Auto
Automatically optimize image
18
Hot-key
Select your preset keys quickly
19
Info
Display source image information
20
Exit
Return to previous level or exit menus if at top level
21
Enter
22
OSD
Use to hide or show menus
23
Focus
Adjust focus to improve image clarity as desired
24
Zoom
Adjust zoom to achieve a desired image size
25
Lens H
Adjust the lens H to position the image horizontally
26
Lens V
Adjust the lens V to position the image vertically
27
Swap
Swap the main and PIP/PBP images
28
Layout
Adjust the PIP/PBP layout

Adjust a setting UP or DOWN

Navigate within a menu

Select a highlighted menu item

Change or accept a value
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 2: Introduction
2.1.5 LED Indication Chart
The LED status indicators are located on the rear of the projector. Each LED
is defined below.

LAMP 1 LED
Projector State

Failed to strike lamp after 5 attempts (strike attempts
will stop).

Lamp has unexpectedly shut down (system goes
into cool down state).
Red (short blink)
Lamp time has expired and lamp should be replaced.
(projector also begins to display the replace lamp OSD
message at startup).
Yellow (no blink)
Lamp 1 turn ON ok
Green (no blink)
Projector is switching to Lamp 1 (Lamp 2 is off)
(selected by OSD menu “Current Lamp”: 1/ 2/ Both )
Lamp is off

LED Status
Green (short blink)
Off
LAMP 2 LED
Projector State

Failed to strike lamp after 5 attempts (strike attempts
will stop).

Lamp has unexpectedly shut down (system goes
into cool down state).
LED Status
Red (short blink)
Lamp time has expired and lamp should be replaced.
(projector also begins to display the replace lamp OSD
message at startup).
Yellow (no blink)
Lamp 2 turn ON ok
Green (no blink)
Projector is switching to Lamp 2 (Lamp 1 is off)
(selected by OSD menu “Current Lamp”: 1/ 2/ Both )
Lamp is off
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Green (short blink)
Off
2-7
Section 2: Introduction

STATUS LED
Projector State

Projector is in OFF state (without AC plug in)
Off
Projector is in standby mode (AC plug in)
Yellow (no blink)
Projector is in startup state
Yellow long blink
Projector is in cool down state
Yellow long blink
Projector is in flash update state
Flashing Green/
Yellow
Fan failure
Red (short blink)
Over-temperature
Red (no blink)
Projector communications (Read/Write EEPROM)
Green (blink very
quickly)
All other states
Green (no blink)
SHUTTER LED
Projector State
2-8
LED Status
LED Status
Shutter is Open
Green
Shutter is Closed
Yellow (no blink)
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 2: Introduction
2.2
Key Features

HD 0.65” 1920 × 1080 resolution or WUXGA 0.67” 1920 × 1200 resolution

Projection lens compatibility (except 0.8:1 Fixed Lens):
-
Horizontal offset ranges: +/-20%
-
Vertical offset ranges: +120%/-40% (WUXGA) and +134%/-40% (HD)
NOTE:
 Measurements are based on industry standards where offset is calculated as a ratio of the number of pixels shifted
up/down to half the image size.

Dynamic aperture enabled (full white to full dark contrast ratio): 5000:1
(Nominal)

Dual mercury lamp illumination with 330W

10-bit image processor electronics with modular design

All video formats can be resized to full screen either horizontally or
vertically while maintaining aspect ratio

User control via Ethernet (Web GUI), OSD (On-Screen Display), or remote
control (either in IR or wired mode)

Weight:
-
Maximum product weight (with lens removed): 19.5kg (43lb.)
-
Maximum shipping weight (includes packaging): 28kg (62lb.)
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
2-9
Section 2: Introduction
2.3
List of Components
This projector comes with all the items shown below. Check to make sure your
package is complete. Contact your dealer if anything is missing.

Projector with built-In keypad

IR remote control

Power cord x 3
-
UK
-
USA
-
Europe

DVI to HDMI dongle

Lamp module with installed lamps

User manual (CD)

Ceiling mount (optional accessory)

Fixed Lens (optional accessory):
-

Lens 0.8:1 Fixed Short (Zero offset)
Zoom Lenses x 4 (optional accessory):
-
Lens 1.2-1.5:1 Fixed Short
-
Lens 1.5-2.0:1 Zoom
-
Lens 2.0-4.0:1 Zoom
-
Lens 4.0-7.0:1 Long Zoom
NOTE:
 Due to the difference in applications for each country, some regions may have different accessories.
2-10
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 3: Installation
3.
INSTALLATION
3.1
Connecting to Computer
Desktop
1
Ind.
Laptop
2
USB
RS232 IN
Ethernet
VGA-OUT
3
Wired Keypad
DC5V
1-VGA
Connector Name
DC12V
SVID
2-VGA
Ind.
4
CVBS
1-HDMI
5
Green/Y
Blue/Pb
Red/Pr
2-HDMI
R
G
Connector Name
B
H/C
Ind.
6
V
Connector Name
1
Network Cable
2
VGA out Cable
3
RS232 Cable
4
VGA in Cable
5
HDMI to DVI Cable
6
Power Cord
NOTE:
 The diagram shows the cables/connectors that may be used to connect to various devices.
 Due to the difference in applications for each country, the accessories required in some regions may be different from those

shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
3-1
Section 3: Installation
3.2
Connecting to Video Equipment
Component video output equipment
DVD player
Video cassette recorder
4
1
3
6
7
8
9
1
10
11
5
2
Ind.
USB
RS232 IN
Ethernet
VGA-OUT
Wired Keypad
Connector Name
DC5V
1-VGA
DC12V
SVID
2-VGA
CVBS
1-HDMI
Green/Y
Blue/Pb
Red/Pr
2-HDMI
R
G
B
H/C
V
Ind.
Connector Name
Ind.
Connector Name
1
3 RCA Component
Cable
2
15-Pin to 3 RCA Component/
HDTV Adaptor
3
Female 2.5mm (ID) x 5.5mm (OD) plug
to Standard 3.5mm Stereo Plug
4
VGA to RGB SCART
5
VGA in Cable
6
Standard 3.5mm Stereo Cable
7
S-Video Cable
8
Composite Video Cable
9
HDMI Cable
10
RCA-BNC Cable
11
Power Cord
NOTE:
 The diagram shows the cables/connectors that may be used to connect to various devices.
 Due to the difference in applications for each country, the accessories required in some regions may be different from those



3-2
shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
5V Port: provides a constant 5 Volt, 2 Amp DC output when the projector is powered on.
12V Port: provides a 12 Volt, 0.25 Amp DC output when the projector is on. This can be disabled in the menu.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 3: Installation
3.3
Powering the Projector ON
1. Ensure that the power cord and signal cable are securely connected. The
Status LED is solid yellow. 1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
2. Turn on the lamp by pressing “ ” on the remote control or on the built-in
keypad. The Status LED is yellow with a long blink.1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
The startup screen displays in approximately 10 seconds.
3. Turn on the source. Select Input Key on the remote control to select an
input source (VGA1, VGA2, BNC, HDMI1, HDMI2, Component, S-Video or
1 2 3 4 5 6 7 8 9 10
Composite Video).
11 12 13 14 15 16 17 18 19 20
4. The projector detects the source you selected and displays the image.
NOTE:
 The first time the projector is used, the preferred language may be selected from the main menu after the startup screen is
displayed.
1
2
3 4 5 on6
Power
7
8
9 10
11 12 13 14 15 16 17 18 19 20
2 3 4 LED
5 6
Power
1
7
8
9 10
11 12 13 14 15 16 17 18 19 20
USB
RS232 IN
Wired Keypad
DC5V
DC12V
SVID
CVBS
Green/Y
Blue/Pb
Red/Pr
1
2
3 4 5 on6
Power
7
8
9 10
11 12 13 14 15 16 17 18 19 20
Ethernet
VGA-OUT
3.4
1-VGA
2-VGA
1-HDMI
2-HDMI
R
G
B
H/C
1
2
3
4 5 Key
6 7
Input
8
9 10
11 12 13 14 15 16 17 18 19 20
V
Powering the Projector OFF
1. Press “ ” on the built-in keypad or on the remote control to turn off the
projector. A warning message will appear on the displayed image.
2. Press “ ” again to confirm your selection. If you do not press “ ” again,
the warning message will disappear after 10 seconds.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
3-3
Section 3: Installation
3.5
Adjusting the Projector Position
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Here are some general guidelines:

Position the projector on a flat surface at a right angle to the screen. The
projector (with the standard lens) must be at least 3 feet (0.9m) from the
projection screen.

Position the projector to the desired distance from the screen. The
distance from the lens of the projector to the screen, the zoom setting, and
the video format determine the size of the projected image.

For the fixed short lens, the image exits at a default angle. However, the
lens shift feature makes the image offset variable.

Lens throw ratio:
-
Lens 0.8:1 Fixed Short (Zero offset)
-
Lens 1.2-1.5:1 Fixed Short
-
Lens 1.5-2.0:1 Zoom
-
Lens 2.0-4.0:1 Zoom
-
Lens 4.0-7.0:1 Long Zoom

Do not roll the projector more than 20 degrees from side to side.

Do not put the projector on either side to project an image.
20°
20°
3-4
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 3: Installation

The vertical image offset (shift) ranges for the projector are +120%/-40%
(WUXGA) and +134%/-40% (HD). Offset is +720 pixels for both WUXGA
and HD. The horizontal image offset is +/-20% (+/- 192 pixels).

The method for calculating lens offset complies with Industry standards.
Example for Vertical lens offset:
-
At 0% offset (or on axis), the center of the image is on the lens center,
so that half of the image appears above and half appears below the
lens center.
-
At +100% offset, all (or 100%) of the image will appear above the lens
center.
-
The % offset is calculated as the ratio of the number of pixels shifted
up/down to half the image size. Examples for WUXGA:
 Shifting up 600 pixels gives offset of 600/600 * 100% = 100%
 Shifting down 600 pixels gives offset of -600/600 * 100% = -100%
 Shifting up 720 pixels gives offset of 720/600 * 100% = 120%
 Shifting up 240 pixels gives offset of 240/600 * 100% = 40%
WUXGA Projectors:
Vertical Image Offset: 0% Offset (WUXGA)
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
600 pixels
above lens
center.
Lens center
600 pixels
below lens
center.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
3-5
Section 3: Installation
Vertical Image Offset: 120% Offset (WUXGA)
Image has been offset 720 pixels above lens
center, so the center of the image is now 720
pixels above where the center of the image
was at 0% offset (or lens center).
The offset is
+720/600 * 100% = +120%.
720 pixels
of shift
above lens
center.
Lens center
Vertical Image Offset: -40% Offset (WUXGA)
Image has been offset 240 pixels below lens
center, so the image has an offset of
-240/600 * 100% = -40%
240 pixels
of shift
below lens
center.
Lens center
Total of
840 pixels
(600+240)
of display
are below
lens center.
3-6
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 3: Installation
HD Projectors:
Vertical Image Offset: 0% Offset (HD)
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
540 pixels
above lens
center.
Lens center
540 pixels
below lens
center.
Vertical Image Offset: 134% Offset (HD)
Image has been offset 720 pixels above lens
center, so the center of the image is now 720
pixels above where the center of the image
was at 0% offset (or lens center).
The offset is
+720/540 * 100% = +134%.
720 pixels
of shift
above lens
center.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Lens center
3-7
Section 3: Installation
Vertical Image Offset: -40% Offset (HD)
Image has been offset 216 pixels below lens
center, so the image has an offset of
-216/540 * 100% = -40%
216 pixels
of shift
below lens
center.
Lens center
Total of
756 pixels
(540+216)
of display
are below
lens center.
Horizontal Image Offset: +/-20% Offset
1920 pixels
+192 pixels
Lens center
-192 pixels
Image has been offset 192 pixels
left or right of lens center.
The image has an offset of
+192/960 * 100% = +20%, or
-192/960 * 100% = -20%
3-8
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 3: Installation
3.6
Lamp Installation
The projector automatically detects the lamp life. When the lamp life is nearing
the end of use, you will receive a warning message. When you see this
message, please contact your local reseller or service center to change the
lamp as soon as possible. Make sure the projector has been cooled down for
at least 30 minutes before changing the lamp.
Installation Steps:
1.
2.
3.
4.
5.
6.
7.
Turn off the lamp:
Note the number of the lamp that
needs to be replaced on the “Current
Lamp” menu.
Turn the projector OFF and
disconnect the power cord.
Wait for lamp cool down:
Allow the projector to cool down for
at least 30 minutes.
Open the lamp door:
Unscrew the two screws on the
lamp door.
Open the lamp door located on the
top-rear of the projector.
Remove the old lamp:
Loosen the two captive screws
securing the lamp.
Lift up the lamp by grasping handle
and remove the lamp module slowly
and carefully.
Install the new lamp:
Replace the lamp with a new one
and tighten two screws. Make sure
the lamp is set properly and secure.
Close the lamp door:
Put the Lamp Door back and tighten
two screws.
Reset the lamp hours:
Turn the projector ON and use
“Reset Lamp Hours�����������������
”����������������
after the lamp
module is replaced.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
A
B
3-9
Section 3: Installation
3.7
Lens Installation
Lens installation and replacement should be completed by Christie accredited service
personnel only. When handling the projector after lens installation, make sure the
front lens cap is placed on the lens to protect the lens surface from potential damage.
When carrying or moving the projector, do not handle by the lens. This may damage
the lens, the chassis or other mechanical parts within the projector.
Installation Steps:
1.
2.
3.
4.
5.
6.
7.
8.
9.
3-10
Center the lens:
Ensure that the lens is at or near
its center position. Attempting to
remove the lens when at a large
offset may cause damage to the
lens assembly. Center the lens
while the projector is switched on
by pressing the lens horizontal or
vertical button and then pressing
Enter.
Turn off the projector:
Turn the projector OFF and
disconnect the power cord.
Wait for projector cool down:
Allow the projector to cool down for
at least 1 minute before replacing
the lens.
Open the lens door:
Push and open the lens door located
on the top-front of the projector.
Remove the lens:
Push the release lever up to release
the lock. (Figure C-1) Remove
the lens through the front of the
projector.
Remove the lens cap (1):
Remove the rear lens cap from the
lens. Keep the front lens cap on the
lens to protect it during installation.
Install the new lens:
Align the lens interface plate with
the lens mount. Fully insert the
assembly straight into the lens
mount without turning.
Push the release lever down to lock
the lens in place.(Figure C-2)
Close the lens door:
Lower the Lens Door and slide back
into the secured position.
Remove the lens cap (2): Remove
the front lens cap.
A
B
C-1
C-2
D
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 3: Installation
3.8
Ceiling Mount Installation
The projector can be inverted and suspended from the ceiling using a specially
designed ceiling mount fixture. This mounting is recommended for those that
want the projector out of plain view or have limited amount of space for the
projector. For more information, contact your dealer.
WARNING

Use only the Christie approved ceiling mount kit designed for your
projector.

When not mounted properly, the projector may fall, causing hazards or
injury. The warranty on this projector does not cover any damage caused
by the use of any non-recommended ceiling mount kit or installation of the
ceiling mount kit in an improper location.

Refer to the installation instructions and safety guidelines provided in the
kit.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
3-11
Section 4: Operation
4.
OPERATION
4.1
Using the On-Screen Display Menus
The projector has multilingual On-Screen Display (OSD) menus that allow you
to make image adjustments and change a variety of settings.
1. Most of the projector controls are accessed from within the projector menu
system. There are several groups of related functions, with each group
selectable from the Main menu as shown below. Press the MENU button on
the remote control or on the built-in keypad on the rear of the projector to
display the main menu.
2. Use the arrow keys to navigate within the menu and adjust a setting up or
down.
3. Press ENTER to select a highlighted menu item or use it to change or
accept a value.
4. Select the next item that you want to adjust in the menu and adjust it as
described above.
5. Press EXIT to return to the previous menu or exit menus if at top level.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
4-1
Section 4: Operation
4.2
Size & Position Menu
Size Presets
Display an image with the detected size, or resize the image by maximizing
either the height, width or both, or resize to the maximum size possible while
keeping the original aspect ratio.

Auto: Display with the detected size.






Native: Display in its native resolution.
4:3: Retain 4:3 aspect ratio.
Letterbox: Display with the black borders on the top and bottom.
Full Size: Fill the screen (regardless of the source).
Full Width: Fill display width and keep aspect ratio.
Full Height: Fill display height and keep aspect ratio.
Overscan
Remove noise around the image.
Pixel Track
Steady flickering or several soft vertical stripes or bands across the entire
image indicates poor pixel tracking. Proper pixel tracking ensures that the
image quality is consistent across the screen, the aspect ratio is maintained,
and that the pixel phase can be optimized.
4-2
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 4: Operation
Pixel Phase
Adjust pixel phase when the image still shows shimmer or noise after pixel
tracking is optimized. Pixel phase can adjust the phase of the pixel-sampling
clock relative to the incoming signal.
Horz Position
Move the image right or left within the area of available pixels.
Vert Position
Move the image up or down within the area of available pixels.
2D Keystone


Horz Keystone: Adjust the keystone horizontally and make a more square
image.
Vert Keystone: Adjust the keystone vertically and make a more square
image.
Basic Geometry Correction


Horz Pincushion: Adjust the pincushion horizontally and make a more
square image.
Vert Pincushion: Adjust the pincushion vertically and make a more square
image.
Digital Zoom
Change the size of projector’s display area. If the display area has been
resized by this setting, it can be moved by changing the Digital Horz Shift and
Digital Vert Shift settings.
Digital Horz Shift
Move the display area horizontally if its size has been changed by the Digital
Zoom setting.
Digital Vert Shift
Move the display area vertically if its size has been changed by the Digital
Zoom setting.
Auto Image
Force the projector to reacquire and lock to the input signal. This is useful
when signal quality is marginal.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
4-3
Section 4: Operation
4.3
Image Settings Menu
Brightness
Adjust the intensity of the image.
Contrast
Adjust the degree of difference between the lightest and darkest parts of the
picture and change the amount of black and white in the image.
Color Space
Select a color space that has been specifically tuned for the input signal.
Useful only for analog signals and certain digital sources.
Detail
Select the edge clarity of the image.
Video Options
This function is used with video sources only.




4-4
Color: Adjust a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Tint: Adjust the red-green color balance in the image of NTSC video
images. The tint setting applies to NTSC video sources only.
Noise Reduction: Reduce temporal or spatial noise in the image.
Flesh Tone Correction: Control the amount of flesh tone correction applied
to the image.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 4: Operation



Video Black Level: Analyze the current input image and calculate an offset
value which is then added to the analog to digital converter black level
value. This ensures optimum black level for each analog source.
Detect Film: Control film mode detection and determine whether the
original source of the input video was film or video.
Closed Captions: Control closed caption display while audio is not muted.
If this setting is not off, audio is not muted, the source is NTSC and
contains captions on the selected channel, then the projector must display
caption text overlaid on the image.
Input Levels

Adjust the gain of the red, green, or blue channel of the image.

Adjust the offset of the red, green, or blue channel of the image.

Sync Threshold: (progressive signals only) If a hardware device, such as a
DVD player, is not syncing properly with the projector, select this option to
help it to sync when connected to the projector.
Picture Settings
Optimize the projector for displaying images under certain conditions, such
as presentation, video, bright, whiteboard, blackboard, beige wall and userdefinable preset.
Save to User
Adjust the image settings and select Save to User as a picture setting. You
can recall these settings in the future by selecting the User in the Picture
Settings menu.
DynamicBlack™
Select the check box to constantly adjust the aperture based on the amount of
black in the current scene.
Advanced Image Settings





Gamma: Select the appropriate gamma from Video, Film, Bright, and CRT.
BrilliantColor™: Produce an expanded on-screen color spectrum that
delivers enhanced color saturation for bright, true-to-life images.
White Peaking: (video source only) Increase the brightness of whites that
are near 100%.
Color Temperature: Change the intensity of the colors. Select a listed
relative warmth value.
Edge Enhancement: Apply the edge enhancement process.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
4-5
Section 4: Operation
4.4
Configuration Menu
Language
Allows you to select an available language for the OSD display.
Lens Settings




Focus and Zoom: Adjust the focus and zoom the image in or out.
Lens Shift: Shift the lens up and down or left and right.
Lock Lens Motors: Select this function to prevent all lens motors from
moving. It will disable the Zoom, Focus, Horizontal and Vertical Position
settings, effectively locking out any changes and overriding all other lens
features. This is particularly useful to prevent accidental lens position
changes in multi-projector installations.
Lens Calibration: Calibrate the lens center
Ceiling Mount
Turn the image upside down for ceiling-mounted projection.
Rear Projection
Reverse the image so you can project from behind a translucent screen.
4-6
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 4: Operation
Menu Preferences




Menu Horz Position: Change the horizontal position of the OSD items.
Menu Vert Position: Change the vertical position of the OSD items.
Show Messages: Display status messages on the screen.
Menu Transparency: Change OSD menu background to be transparent.
NOTE:
 As the value increases, more of the image behind the menu is visible.



Splash Screen: Choose which splash screen is to be used.
PIN Protect: The PIN (personal identification number) feature allows you
to password protect your projector. Once you enable the PIN feature, you
must enter the PIN before you can project an image.
Change PIN: Allows you to change the PIN.
Power Management




Standby Mode: The projector is in standby mode when connected to AC
power.
AC Power On: The projector automatically turns on when electrical power
is connected.
Auto Shutdown: Automatically turns the projector off after no signals are
detected for a preset number of minutes. If an active signal is received
before the projector powers down, the image will be displayed.
Sleep Timer: Allows the projector to automatically power off after it has
been on for a specified amount of time.
High Altitude
Set high altitude mode ON/OFF.
Communications



Network: Allow you to setup network settings.
- DHCP: Turn the DHCP ON/OFF.
- IP Address: Assign Network IP Address.
- Subnet Mask: Assign Network Subnet Mask.
- Default Gateway: Assign Network Default Gateway.
- Host Name: Display the host name.
- MAC Address: Displays network MAC Address value.
- Show Network Messages: Turn network messages ON/OFF.
- Restart Network: Restart the network.
- Network Factory Reset: Perform factory reset.
Baud Rate: Select the serial port and baud rate.
Serial Port Echo: Control whether the serial port echoes characters.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
4-7
Section 4: Operation
12V Trigger
Set 12V trigger ON/OFF. The 12V trigger is an interface that is used for
electrical projector screens. The projector screen is lowered or raised
automatically when the projector is switched ON/OFF.
Hot-Key Settings
Assign a different function to the hot-key by highlighting the function in the
list and pressing ENTER. Choose a function that does not already have a
dedicated button, and assign the hot-key to that function, allowing you to
quickly and easily use the chosen function.
Service



4-8
Projector Info: Display current projector settings (read-only).
Factory Reset: Restore all settings to their default value.
Test Pattern: Choose the desired internal test pattern to display, or select
OFF to turn off a test pattern.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 4: Operation
4.5
Lamp Menu
Lamp Power
Set the lamp power in Watts. The Power setting represents the amount of
lamp(s) power.
Current Lamp
Select which lamp(s) is in use.
Whisper Mode
Set whisper mode ON, OFF, Auto or assign a lamp to whisper mode.
Lamp Auto Switch
Control when the projector switches lamps. Options include: on failure only, at
power-up, or after a set number of hours.
Lamp Auto Switch Time
Set a number of hours for Lamp Auto Switch.
Lamp Info
Display current lamp(s) settings (read-only).
Lamp Life Settings
Set a number of hours for lamp life.
Reset Lamp Hours
Reset the lamp used hours counter to zero. Do this after changing the lamp.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
4-9
Section 4: Operation
4.6
Status Menu
The read-only Status menu lists a variety of details about the standard and
optional components currently detected in the projector.
4-10
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 4: Operation
4.7
Input Switching & PIP Menu
Main Input
From the list of active inputs, select one to be used as the main image.
PIP/PBP Input
From the list of active inputs, select one to be used as the PIP/PBP.
PIP/PBP Enable
Toggle between displaying two sources at once (Main and PIP/PBP images)
or one source only. The check box turns the PIP/PBP source ON and OFF.
Swap
Change the main image to PIP/PBP, and the PIP/PBP to main image.
Swapping is available only when PIP/PBP is enabled.
Size
Select the PIP/PBP size to small, medium or large.
Layout
Set the location of the PIP/PBP image on the screen.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
4-11
Section 4: Operation
NOTE:
 PIP/PBP layout and size table as described below.
 P : indicates primary source region (lighter color).
 * : Both source regions are the same size.
PIP/PBP Layout
PBP, Bigger Left
Over-Under, Bigger Upper
PIP/PBP Size
Small
PIP-Bottom Right
PIP-Bottom Left
PIP-Top Left
PIP-Top Right
*
P
P
P
Large
P
P
P
PBP, Bigger Right
Over-Under, Bigger Lower
Medium
P
P
*
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
*
*
Timing Detection
Select timing detection mode to wide or normal.
Source Info
Display current source settings (read-only).
Enable Source Hot-Key
Toggle the check box to enable or disable the main source hot-key.
Source Hot-Key
Allows you to assign a different source to the hot-key. Highlight an input and
press ENTER to choose a different one.
Input Key
Use it to list all of the sources or change the sources.
4-12
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 4: Operation
4.8
Language
Allows you to select an available language for the OSD display.
4.9
Test Pattern
Choose the desired internal test pattern to display, or select OFF to turn off a
test pattern.






OFF
Black
White
Checkerboard
Grid
Color Bars
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
4-13
Section 5: Appendices
5.
APPENDICES
5.1
Troubleshooting
If you experience a problem with your projector, please refer to the following
information. If a problem persists, please contact your local reseller or service
center.


No image appears on-screen
-
Make sure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
-
Check if the projection lamp has been securely installed.
-
Make sure you have removed the lens cap and the projector is
switched ON.
Partial, scrolling or incorrectly displayed image
-
Press “AUTO” on control panel or on remote control.
-
If you are using a PC (for Windows 95, 98, 2000, XP, Windows 7):
 Open the “My Computer” icon, the “Control Panel” folder, and then
double click on the “Display” icon.
 Select the “Settings” tab.
 Verify that your display resolution setting is lower than or equal to
WUXGA (1920 × 1200).
 Click on the “Advanced Properties” button. If the projector is still
not projecting the whole image, you will also need to change the
monitor display you are using. Refer to the following steps:

Verify the resolution setting is lower than or equal to WUXGA
(1920 × 1200).

Select the “Change” button under the “Monitor” tab.

Click on “Show all devices”. Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need
under the “Models” box.

Verify that the resolution setting of the monitor display is lower
than or equal to WUXGA (1920 × 1200).
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
5-1
Section 5: Appendices
-
If you are using a Notebook:
 First, follow the steps above to adjust resolution of the computer.
 Press the appropriate keys listed below for your notebook
manufacturer to send signal out from notebook to projector.
Example: [Fn]+[F4]
Notebook Brand


5-2
Acer
[Fn]+[F5]
Asus
[Fn]+[F8]
Dell
[Fn]+[F8]
Gateway
[Fn]+[F4]
IBM/Lenovo
[Fn]+[F7]
HP/Compaq
[Fn]+[F4]
NEC
[Fn]+[F3]
Toshiba
[Fn]+[F5]
Mac Apple
System Preference  Display 
Arrangement  Mirror display
If you experience difficulty changing resolutions or your monitor
freezes, restart all equipment including the projector.
The screen of the Notebook or PowerBook computer is not displaying your
presentation
-

Function Keys
If you are using a Notebook PC
Some Notebook PCs may deactivate their own screens when a
second display device is in use. Each of them has a different method
of reactivation. Please refer to your computer manual for detailed
information.
Image is unstable or flickering
-
Use “Pixel Track” and “Pixel Phase” to correct it.
-
Change the monitor color setting on your computer.
Image has vertical flickering bar
-
Use “Auto Image” to make an adjustment.
-
Check and reconfigure the display mode of your graphic card to make
it compatible with the projector.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 5: Appendices




Image is out of focus
-
Make sure the lens cap is removed.
-
Adjust lens focus to fit.
-
Make sure the projection screen is between the required distance.
The image is stretched when displaying 16:9 DVD title
-
When you play anamorphic DVD or 16:9 DVD, the projector will show
the best image when the projector display mode is set to 16:9 in the
OSD.
-
If you play 4:3 format DVD titles, please change the format to 4:3 in the
projector OSD.
-
If the image is still stretched, you will also need to adjust the aspect
ratio by setting the display format as 16:9 (wide) aspect ratio type on
your DVD player.
Image is too small or too large
-
Adjust lens zoom to fit.
-
If it does not fill the screen properly, verify that the correct lens is in use
or change the position of the projector.
Image has slanted sides
-

Reposition the projector so that it is perpendicular to the screen.
Lamp burns out or makes a popping sound
-
When the lamp reaches its end of life, it will burn out and may make a
loud popping sound. If this happens, the projector will not turn on until
the lamp module has been replaced.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
5-3
Section 5: Appendices
5.2
Input Specification
Signal
Type
Resolution
Frame Rate
(Hz)
HDMI 1
HDMI 2
VGA 1
VGA 2
BNC
Component
S- video
CVBS
640x480
60
●
●
●
●
●
640x480
75
●
●
●
●
●
640x480
85
●
●
●
●
●
800x600
60
●
●
●
●
●
800x600
75
●
●
●
●
●
800x600
85
●
●
●
●
●
1024x768
60
●
●
●
●
●
1024x768
75
●
●
●
●
●
1024x768
85
●
●
●
●
●
1280x768
60
●
●
●
●
●
1280x800
50
●
●
●
●
●
1280x800
60
●
●
●
●
●
1280x1024
60
●
●
●
●
●
1280x1024
75
●
●
●
●
●
1280x1024
85
●
●
●
●
●
1400x1050
60
●
●
●
●
●
1600x1200
60
●
●
●
●
●
1680x1050
60
●
●
●
1920x1200RB
60
●
●
●
●
●
1920x1200RB
50
●
●
●
●
●
60
●
●
●
PAL (B,G,H,I)
50
●
●
●
PAL (N)
50
●
●
●
PAL (M)
60
●
●
●
SECAM (M)
50
●
●
●
PC
NTSC
PAL
SECAM
5-4
NTSC
(M, 4.43)
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Section 5: Appendices
Signal
Type
Resolution
Frame Rate
(Hz)
HDMI 1
HDMI 2
VGA 1
VGA 2
BNC
Component
480i
60
●
●
●
●
●
576i
50
●
●
●
●
●
480p
60
●
●
●
●
●
576p
50
●
●
●
●
●
1080i
60
●
●
●
●
●
●
720p
50
●
●
●
●
●
●
720p
60
●
●
●
●
●
●
1080p
24
●
●
●
●
●
●
1080p
25
●
●
●
●
●
●
1080p
30
●
●
●
●
●
●
1080p
50
●
●
●
●
●
●
1080p
60
●
●
●
●
●
●
S- video
CVBS
SDTV
●
EDTV
HDTV
5.3
PIP/PBP Compatibility
Main
PIP/PBP
HDMI 1
HDMI 2
VGA 1
VGA 2
BNC
Component
S-video
Composite
●
-
●
-
●
-
-
●
-
●
-
●
●
●
-
●
-
-
●
-
●
●
●
-
-
●
●
HDMI 1
HDMI 2
●
VGA 1
-
●
VGA 2
●
-
●
BNC
-
●
-
●
Component
●
-
●
-
●
S-video
-
●
-
●
-
●
Composite
-
●
-
●
-
●
-
● : PIP/PBP combinations are enabled
- : PIP/PBP combinations are disabled
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
5-5
Section 5: Appendices
5.4
5.5
Declaration of Conformity for EU Countries

EMC Directive 2004/108/EC (including amendments)

Low Voltage Directive 2006/95/EC

Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
Federal Communications Commission (FCC) Warning
WARNING
5-6

A shielded-type power cord is required in order to meet FCC emission
limits and also to prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord be used.

Use only shielded signal cables to connect I/O devices to this equipment.
E Series User Manual
020-000287-01 Rev. 1 (01-2011)
Corporate offices
USA – Cypress
ph: 714-236-8610
Canada – Kitchener
ph: 519-744-8005
Worldwide offices
United Kingdom
ph: +44 118 977 8000
Germany
ph: +49 2161 664540
France
ph: +33 (0) 1 41 21 44 04
Hungary/Eastern Europe
ph: +36 (0) 1 47 48 100
Singapore
ph: +65 6877 8737
Shanghai
ph: +86 21 6278 7708
Beijing
ph: +86 10 6561 0240
Korea
ph: +82 2 702 1601
Japan
ph: +81 3 3599 7481
For the most current technical documentation,
please visit www.christiedigital.com
*36.8HP05G001-B*
P/N 36.8HP05G001-B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement