INSTALLATION
INSTRUCTIONS
PARTS LIST
Remote Engine Starter Unit Kit
P/N 08E91-E54-200
Transmitter
Accessory
REMOTE CONTROL
ENGINE STARTER
3 Relays
Application
2014 RLX
Relay bracket
Control unit
Antenna
2 Flange nuts
Washer nut
21 Wire ties
ID label
5 Urethane tapes
Remote Control Engine Starter Attachment Kit
P/N 08E92-TY2-200
Engine starter harness
3A Fuse
Clip
Control unit bracket
Publications No.
BII 13404
Issue Date
JAN 2013
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301) 08E92-TY2-2000-90
1 of 30
Fuse label A
Fuse label B
Caution label
Accessory User’s Information Manual
Quick Start Guide
TOOLS AND SUPPLIES REQUIRED
Flat-tip screwdriver
Phillips screwdriver
Ratchet
10 mm Socket
Isopropyl alcohol
Shop towel
Scissors
HDS/MVCI
Masking tape
Diagonal cutters
Ruler
Tape
10 mm Open end wrench
The following tool is available through the Honda Tool and
Equipment Program. On the iN, click on: Service >
Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857.
• Plastic Trim Tool (T/N SILTRIMTL10)
Illustration of the Remote Control Engine Starter on the Vehicle
ANTENNA
2 of 30
ENGINE
STARTER
HARNESS
3A FUSE
20A
FUSES
3 RELAYS
CONTROL UNIT
QB51001AH
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
INSTALLATION
Client Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
1.
Disconnect the negative cable from the battery.
2.
Attach the ID label.
• Using isopropyl alcohol on a shop towel, thoroughly clean the transmitter where the ID label will attach.
• Attach the ID label to the transmitter in the area as shown.
NOTE: The remote is factory set for driver 1 remote control. To program the driver 2 remote, follow the
“Register New Transmitter” instructions on ISIS.
3.
Using a plastic trim tool, remove the left and right lenses from the front roof module (two retaining tabs for each lens).
VEHICLE
CONNECTORS
6 RETAINING
TABS
2 RETAINING
TABS
LEFT
LENS
FRONT
ROOF
MODULE
2 BOLTS
2 RETAINING
TABS
RIGHT LENS
ID LABEL
TRANSMITTER
PLASTIC
TRIM TOOL
QB62650AK
4.
Remove the front roof module (two bolts, six retaining tabs, and unplug the vehicle connectors).
5.
Remove the driver’s and passenger’s sunvisor holders.
Clean with isopropyl alcohol.
QB20939DH
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301)
DRIVER’S
SUNVISOR HOLDER
(Rotate.)
PASSENGER’S
SUNVISOR HOLDER
(Rotate.)
QB62701AK
3 of 30
6.
Remove the driver’s sunvisor:
• Pivot the driver’s sunvisor downward.
• Wrap tape around the tip of flat-tip screwdriver.
• Locate the slot in the bracket cover, and insert the flat-tip screwdriver into the slot. Push in and hold the hook.
• While holding the hook, push up on the sunvisor and rotate it toward the door.
NOTE: If the hook did not stay pushed in, return the sunvisor to its original position and repeat this step.
FLAT-TIP
SCREWDRIVER BRACKET COVER
• Unplug the vehicle connector, and remove the driver’s sunvisor.
TAPE HOOK
DRIVER’S
SUNVISOR
FRONT
VEHICLE
CONNECTOR
DRIVER’S
SUNVISOR
QB40203AJ
7.
Remove the driver’s A-pillar trim.
• Pull away the driver’s door opening seal from the
A-pillar trim.
• Gently pull the A-pillar trim away from the A-pillar to release the three clips.
Pull the clip.
Make sure the hook slides into the bracket cover.
DRIVER’S A-PILLAR
DRIVER’S
A-PILLAR
TRIM
2 CLIPS
Push the hook.
While pushing in on the hook, rotate the sunvisor toward the door.
QB40202AJ
DRIVER’S DOOR
OPENING SEAL
(Pull away.)
QB40204AJ
4 of 30
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
• To prevent the clips from falling into the body panel area, carefully insert a shop towel between the driver’s A-pillar and the driver’s
A-pillar trim.
DRIVER’S
A-PILLAR TRIM
DRIVER’S
A-PILLAR
8.
Remove the remaining upper clip from the driver’s
A-pillar.
Push two tabs.
DRIVER’S
A-PILLAR
SHOP
TOWEL
QB40205AJ
• Slide the driver’s A-pillar trim upward, and remove the driver’s A-pillar trim.
• Remove the shop towel and any clips.
UPPER
CLIP
(Discard.)
QB40207AJ
9.
Install the new clip (supplied) to the driver’s A-pillar trim, but do not reinstall the trim at this time.
CLIP
(supplied)
UPPER CLIP
DRIVER’S
A-PILLAR
TRIM
DRIVER’S
A-PILLAR TRIM
QB40208AJ
QB40206AJ
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301)
5 of 30
10. Apply tape to the center console panel and the driver’s and passenger’s console side trims as shown. With the vehicle’s parking brake set and wheels chocked, move the shift lever to the N
(neutral) position, and wrap a shop towel around the shift lever.
12. Remove the center lower panel (six clips, four hooks, and unplug the vehicle connectors).
6 CLIPS
2 HOOKS
2 HOOKS
CENTER
LOWER
PANEL
TAPE
SHIFT LEVER
(N POSITION)
SHOP
TOWEL
CENTER
CONSOLE
PANEL
PASSENGER’S
CONSOLE
SIDE TRIM
QB32901AH
11. Remove the center lower trim (three clips, and unplug the vehicle connectors).
3 CLIPS
VEHICLE
CONNECTORS
QB32903AH
13. Pull away the door opening seal, and remove the driver’s dashboard side lid (four clips, two retaining tabs, and three hooks).
4 CLIPS
CENTER LOWER
TRIM
VEHICLE
CONNECTORS
QB32902AH
3 HOOKS
FRONT
DRIVER’S
DASHBOAR
D SIDE LID
2 RETAINING
TABS
DOOR OPENING
SEAL
(Pull away.)
QB32904AH
6 of 30
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
14. Reconnect the negative cable to the battery, then press the engine start/stop button to select the ON mode. Lower the steering wheel.
17. Turn the steering wheel 180° clockwise. Using a plastic trim tool, release the retaining tab.
UPPER COLUMN
COVER
UPPER COLUMN COVER
RETAINING
TAB
MASKING TAPE
STEERING
WHEEL
QB40601AH
15. Attach masking tape to the upper column cover as shown.
16. Turn the steering wheel 90° counterclockwise. Using a plastic trim tool, release the retaining tab.
UPPER COLUMN
COVER
PLASTIC TRIM
TOOL
QB40603AH
18. Release the upper column cover (two retaining tabs and two hooks), and secure the upper column cover to the instrument panel with strips of masking tape.
INSTRUMENT PANEL
MASKING TAPE
2 RETAINING
TABS
2 HOOKS
RETAINING
TAB
PLASTIC TRIM
TOOL
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
QB40602AH
BII 13404 (1301)
UPPER
COLUMN
COVER
QB40604BH
7 of 30
19. Remove one self-tapping screw from the lower column cover. Turn the steering wheel 180° clockwise, and remove the other self-tapping screw from the lower column cover.
22. Remove the lower column cover (one self-tapping screw, and unplug the vehicle connector).
VEHICLE
CONNECTOR
LOWER
COLUMN
COVER 2 SELF-
TAPPING
SCREWS
QB40605AH
20. Press the engine start/stop button to select OFF mode, then disconnect the negative cable from the battery.
NOTE: The steering wheel automatically moves fully in and up. Make sure that the steering wheel is not interfering with the vehicle parts.
21. Remove the driver’s dashboard lower cover (nine clips, and unplug the vehicle connectors and aspirator hose), then remove the plate (two clips).
9 CLIPS VEHICLE
CONNECTORS ASPIRATOR
HOSE
DRIVER’S
DASHBOARD
LOWER COVER
LOWER
COLUMN
COVER
SELF-TAPPING
SCREW
LOWER
COLUMN
COVER
QB40606AH
8 of 30
2 CLIPS
PLATE
QB32905AH
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
23. Turn the knob, and remove the driver’s dashboard under cover (one clip, and unplug the vehicle connector).
CLIP
FRONT
25. Pull away the door opening seal, and remove the driver’s kick panel (two clips).
DOOR OPENING
SEAL
(Pull away.)
VEHICLE
CONNECTOR
2 CLIPS
DRIVER’S
DASHBOARD
UNDER COVER
KNOB
(Turn.)
QB32906AH
24. Remove the driver’s front door sill trim (four clips and six retaining tabs).
4 CLIPS
6 RETAINING
TABS
DRIVER’S KICK
PANEL
QB32908AH
26. Remove the driver’s console side trim (three clips, two hooks, and two retaining tabs).
FRONT
3 CLIPS
2
1
FRONT
2 HOOKS
DRIVER’S
CONSOLE
SIDE TRIM
2 RETAINING
TABS
QB41930AH
DRIVER’S FRONT
DOOR SILL TRIM
QB32907AH
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301)
9 of 30
27. Remove the passenger’s dashboard lower cover
(four clips, and unplug the vehicle connector).
VEHICLE
CONNECTOR
4 CLIPS
FRONT
29. Apply masking tape to the center console panel and the center console as shown, and secure the shop towel to the shift lever with masking tape.
MASKING
TAPE SHOP
TOWEL
MASKING TAPE
FRONT
SHIFT LEVER
PASSENGER’S
DASHBOARD
LOWER COVER
QB32911AH
28. Remove the passenger’s console side trim (six clips and two retaining tabs).
6 CLIPS
FRONT
FRONT
CENTER
CONSOLE
PANEL
CENTER
CONSOLE
MASKING TAPE
QB41932BH
30. Release the center console panel (two self-tapping screws, one hook, and seven clips).
2 SELF-TAPPING
SCREWS
CENTER
CONSOLE
PANEL
HOOK
2 RETAINING
TABS
PASSENGER’S
CONSOLE
SIDE TRIM
QB41931AH
7 CLIPS
QB41933BH
10 of 30
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
31. Release the hook that fastens the right A/T trim from the center console, and remove the right A/T trim
(three clips).
33. Remove the left A/T trim (two clips, and unplug the vehicle connector).
FRONT
LEFT
A/T TRIM
HOOK
RIGHT
A/T TRIM
2 CLIPS
3 CLIPS
RIGHT
A/T TRIM
CENTER
CONSOLE
QB41934AH
32. Release four hooks that fasten the shift boot from the center console, and hold up the shift boot.
FRONT
VEHICLE
CONNECTOR
QB41936AH
34. Remove the center console panel (unplug the vehicle connectors).
CENTER
CONSOLE
PANEL
2 HOOKS
SHIFT BOOT
SHIFT BOOT
VEHICLE
CONNECTORS
QB41937AH
CENTER
CONSOLE 2 HOOKS
QB41935AH
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301)
11 of 30
Routing the Engine Starter Harness
35. Plug the 3A fuse into the fuse box.
FUSE BOX
FRONT VIEW
38. Using isopropyl alcohol on a shop towel, thoroughly clean the engine starter harness fuse block where the fuse labels B will attach.
Clean with isopropyl alcohol.
Plug in here.
3A FUSE FUSE BOX
QB51002AH
36. Using isopropyl alcohol on a shop towel, thoroughly clean the driver’s dashboard under cover where the fuse label A will attach.
Clean with isopropyl alcohol.
ENGINE STARTER
HARNESS
FUSE BLOCK
FUSE LABELS B
(20A ENG.
STARTER)
QB51004AH
39. Attach two fuse labels B to the engine starter harness fuse block.
40. Install three relays to the engine starter harness relay block.
3 RELAYS
FUSE LABEL A
(3A OPTION
FUSE)
Attach in here.
DRIVER’S
DASHBOARD
UNDER COVER
QB51003AH
37. Attach the fuse label A to the driver’s dashboard under cover.
ENGINE STARTER
HARNESS
RELAY BLOCK
QB51005AH
12 of 30
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
41. Install the control unit bracket to the control unit.
43. Under the driver’s dashboard, locate and remove the cap from the stud.
CONTROL
UNIT
FRONT
CONTROL UNIT
BRACKET
QB51006AH
42. Secure the control unit bracket to the vehicle frame with two flange nuts.
FRONT
CAP
STUD
QB51008BH
44. Secure the relay bracket to the stud with one washer nut, and reinstall the cap.
RELAY
BRACKET
STUD
2 FLANGE
NUTS
VEHICLE
FRAME
CONTROL
UNIT
BRACKET
CENTER
CONSOLE
QB51007AH
CAP
(reused)
WASHER
NUT
QB51009BH
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301)
13 of 30
45. Using isopropyl alcohol on a shop towel, thoroughly clean the relay bracket, washer nut, and cap where the urethane tape will attach.
URETHANE TAPE
(Cut in half.)
HALVE OF
URETHANE
TAPE
WASHER
NUT
RELAY
BRACKET
CAP
47. Align the white tape on the engine starter harness with the vehicle clip, and secure the engine starter harness to the vehicle harness with one wire tie.
VEHICLE
CLIP
WIRE TIE
VEHICLE
HARNESS
FRONT
SECTION VIEW
WHITE
TAPE
Clean with isopropyl alcohol
HALVE OF
URETHANE TAPE
QB51010AH
46. Using scissors, cut one urethane tape in half. Wrap one halve of urethane tape around the washer nut.
ENGINE STARTER
HARNESS
QB51011AH
48. Align the other white tape on the engine starter harness with the vehicle clip, and secure the engine starter harness to the vehicle harness with one additional wire tie.
WIRE TIE
VEHICLE
CLIP
WHITE TAPE
VEHICLE
HARNESS
14 of 30
BII 13404 (1301)
ENGINE STARTER
HARNESS
QB51012AH
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
49. Route the engine starter harness as shown. Unplug the vehicle 12-pin connector from the combination light switch, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the combination light switch.
50. Route the engine starter harness as shown. Unplug the vehicle 10-pin connector from the wiper switch, and plug it into the engine starter harness 10-pin connector. Plug the remaining engine starter harness 10-pin connector into the wiper switch.
ENGINE
STARTER
HARNESS
ENGINE
STARTER
HARNESS
ENGINE STARTER
HARNESS
12-PIN CONNECTOR
COMBINATION
LIGHT SWITCH
ENGINE STARTER
HARNESS 10-PIN
CONNECTOR
VEHICLE
10-PIN
CONNECTOR
VEHICLE
12-PIN
CONNECTOR
QB51015AH
ENGINE STARTER HARNESS
12-PIN CONNECTOR
WIPER
SWITCH ENGINE STARTER HARNESS
10-PIN CONNECTOR
QB51013AH
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301)
15 of 30
51. Secure the engine starter harness to the vehicle harness with one wire tie.
Do not pull the 12-pin connector cord too tight.
Do not pull the 10-pin connector cord too tight.
FRONT
53. Press the engine start/stop button to select OFF mode, then disconnect the negative cable from the battery. Remove the driver’s dashboard lower cover.
NOTE: The steering wheel automatically moves fully in and up. Make sure that the steering wheel is not interfering with the vehicle parts.
NUT
(Loosen.)
VEHICLE
BRACKET
FRONT
2 BOLTS
(Loosen.)
ENGINE
STARTER
HARNESS
VEHICLE
HARNESS
WIRE
TIE
FUSE BOX
QB40101AH
54. To gain access to the engine starter harness 12-pin connector, loosen one nut and two bolts from the vehicle bracket, and move the vehicle bracket.
QB51014CH
52. Reinstall the driver’s dashboard lower cover.
Reconnect the negative cable to the battery, then press the engine start/stop button to select the ON mode.
NOTE:
• Make sure that the engine starter harness is not stretched.
• Make sure that the connectors and harness are not pinched, or are not interfering with the steering wheel when it is moved for adjustment.
16 of 30
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
Without Another Accessory Harness 12-pin connector
55. Plug the engine starter harness 12-pin connector into the fuse box.
ENGINE STARTER
HARNESS 12-PIN
CONNECTOR
Plug in here.
FRONT VIEW
FUSE
BOX
QB51016AH
56. Reinstall the vehicle bracket. Go to step 59.
With Another Accessory Harness 12-pin connector
57. If another accessory harness 12-pin connector is plugged into the fuse box, unplug the 12-pin connector from the fuse box, then plug the engine starter harness 12-pin connector into the fuse box.
Remove the dummy connector from engine starter harness 12-pin connector, and plug another accessory harness 12-pin connector into the engine starter harness 12-pin connector.
ANOTHER
ACCESSORY
HARNESS 12-PIN
CONNECTOR
ENGINE
STARTER
HARNESS 12-PIN
CONNECTOR
DUMMY
CONNECTOR
(Discard.)
ENGINE
STARTER
HARNESS 12-PIN
CONNECTOR
Plug in here.
FRONT VIEW
FUSE
BOX
58. Reinstall the vehicle bracket.
QB51017AH
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301)
17 of 30
59. Unplug the vehicle 2-pin connector from the vehicle unit, and plug it into the engine starter harness 2-pin connector. Plug the remaining engine starter harness 2-pin connector into the vehicle unit.
VEHICLE UNIT
VEHICLE 2-PIN
CONNECTOR
61. Route the engine starter harness as shown. Unplug the vehicle 28-pin connector, and plug it into the engine starter harness 28-pin connector. Plug the remaining engine starter harness 28-pin connector into the vehicle 28-pin connector.
ENGINE
STARTER
HARNESS
HOOD
OPENER
ENGINE
STARTER
HARNESS
2-PIN
CONNECTORS
SRS
CONNECTOR
(yellow)
VEHICLE
4-PIN
CONNECTOR
VEHICLE
UNIT
ENGINE STARTER HARNESS
4-PIN CONNECTORS
QB51018AH
60. Unplug the vehicle 4-pin connector from the vehicle unit, and plug it into the engine starter harness 4-pin connector. Plug the remaining engine starter harness 4-pin connector into the vehicle unit.
ENGINE STARTER
HARNESS 28-PIN
CONNECTORS
VEHICLE
28-PIN
CONNECTORS
QB51019BH
18 of 30
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
62. Secure the engine starter harness 28-pin connector and engine starter harness to the vehicle harness with three wire ties.
64. Attach the engine starter harness relay blocks to the relay bracket.
ENGINE
STARTER
HARNESS
RELAY
BLOCKS
VEHICLE
HARNESS
ENGINE
STARTER
HARNESS
3 WIRE TIES
ENGINE STARTER
HARNESS 28-PIN
CONNECTOR
QB51020AH
63. Route the engine starter harness as shown. Attach the clip on the engine starter harness onto the bottom of the fuse box.
FRONT VIEW ENGINE
STARTER
HARNESS
CLIP
RELAY BRACKET
QB51022AH
65. Attach the clip on the engine starter harness onto the bottom of the vehicle connector.
VEHICLE
CONNECTOR
FUSE BOX
ENGINE STARTER
HARNESS CLIP
ENGINE STARTER
HARNESS
QB51021AH
ENGINE STARTER
HARNESS CLIP
ENGINE STARTER
HARNESS QB51023AH
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301)
19 of 30
66. Route the engine starter harness as shown.
CENTER
CONSOLE
68. Route the engine starter harness as shown. Unplug the vehicle 2-pin connector, and plug it into the engine starter harness 2-pin connector. Plug the remaining engine starter harness 2-pin connector into the vehicle 2-pin connector.
ENGINE STARTER HARNESS
2-PIN CONNECTORS
SHIFT
LEVER
VEHICLE 2-PIN
CONNECTORS
ENGINE STARTER
HARNESS
QB51024AH
67. Plug the engine starter harness 28-pin connector into the control unit.
CONTROL UNIT
ENGINE STARTER
HARNESS
28-PIN
CONNECTOR
FRONT
FRONT
ENGINE STARTER
HARNESS
QB51026AH
69. Secure the engine starter harness to the vehicle harness with two wire ties.
FRONT
ENGINE
STARTER
HARNESS
CENTER
CONSOLE
QB51025AH
2 WIRE
TIES
VEHICLE HARNESS
QB51027AH
20 of 30
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
70. Secure the engine starter harness to the vehicle harness with one wire tie.
FRONT
72. Using scissors, cut one urethane tape in half. Wrap two halves of urethane tape around the antenna cable at the measurements shown.
URETHANE TAPE
(Cut in half.)
ANTENNA
CABLE
SECTION
VIEW
ENGINE
STARTER
HARNESS WIRE TIE
VEHICLE
HARNESS
CENTER
CONSOLE QB51028AH
Installing the Antenna
71. Using scissors, cut one urethane tape in half. Wrap two halves of urethane tape to the antenna cable as shown.
NOTE: Do not fold the antenna cable.
ANTENNA
60 mm
(2.4 in.)
20 mm
(0.8 in.)
2 HALVES OF
URETHANE
TAPE
20 mm
(0.8 in.)
ANTENNA
QB51029CH
73. Attach the antenna.
• Attach masking tape to the windshield at the measurement shown.
60 mm
(2.4 in.)
MASKING TAPE
ANTENNA
CABLE
SECTION
VIEW
10 mm (0.4 in.)
CAMERA
COVER
URETHANE TAPE
(Cut in half.)
2 HALVES OF
URETHANE
TAPE
QB62501BK
HEADLINER
QB51403BH
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301)
21 of 30
• Fold back the adhesive backing on the antenna as shown.
• Carefully remove the adhesive backing from the antenna, and attach the antenna to the windshield. Press and hold the antenna firmly in place for 30 seconds.
• Remove the masking tape.
ADHESIVE
BACKING
ANTENNA
ANTENNA
QB51401CH
• Using isopropyl alcohol on a shop towel, clean the windshield where the antenna will attach.
• Attach the antenna with masking tape. Adjust the position of the antenna so there is equal spacing on both sides.
Clean with isopropyl alcohol.
ADHESIVE
BACKING
(Remove.)
MASKING TAPE
(Remove.)
QB51405CH
74. Gently pull down the headliner, and tuck the antenna cable under the headliner. Be careful not to crease the headliner.
HEADLINER
ANTENNA
HEADLINER
Equal spacing on both sides.
MASKING TAPE ANTENNA
QB51404CH
ANTENNA
CABLE
ANTENNA
QB72301AH
22 of 30
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
75. Route the antenna cable down the A-pillar as shown.
Secure the antenna cable to the vehicle harness with five wire ties.
ANTENNA
CABLE
VEHICLE
HARNESS
VEHICLE
FRAME
VEHICLE
HARNESS
WIRE
TIE
ANTENNA
CABLE
77. Route the antenna cable down next to the instrument panel, and tuck the antenna cable between the driver’s A-pillar and the instrument panel.
DRIVER’S
A-PILLAR
INSTRUMENT
PANEL
SECTION
VIEW
5 WIRE
TIES
Be careful not to secure the wire ties over the holes.
FRONT
QB51031AH
76. Using scissors, cut one urethane tape in half.
Starting near the wire tie, wrap three halves of urethane tape around the antenna cable at the measurements shown.
URETHANE
TAPE
(Cut in half.)
URETHANE TAPE
(Remaining in step 46.)
ANTENNA
CABLE
SECTION
VIEW
ANTENNA CABLE
QB51032BH
78. Gently pull the excess antenna cable down and route it as shown. Secure the engine starter harness and the antenna cable to the vehicle harness with one wire tie.
VEHICLE
HARNESS
ANTENNA CABLE
WIRE TIE
3 HALVES OF
URETHANE
TAPE HOOD
OPENER
35 mm
(1.4 in.)
WIRE
TIE
20 mm
(0.8 in.)
ANTENNA
CABLE
20 mm
(0.8 in.)
QB51034CH
ENGINE
STARTER
HARNESS
QB51035AH
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301)
23 of 30
79. Route the antenna cable under the dashboard as shown. Secure the engine starter harness and the antenna cable to the instrument panel with one wire tie.
INSTRUMENT
PANEL
ANTENNA
CABLE
82. Wrap one urethane tape around the engine starter harness and the antenna cable in the location shown.
ANTENNA
CABLE
2 WIRE
TIES
ENGINE STARTER
HARNESS
QB51036AH
80. Secure the antenna cable to the engine starter harness with one wire tie.
81. Continue routing the antenna cable under the dashboard, and secure the engine starter harness and the antenna cable to the hole in the vehicle frame with one wire tie.
ASPIRATO
R HOSE
ENGINE STARTER
HARNESS
URETHANE TAPE
QB51038AH
83. Plug the antenna cable connector into the control unit.
ANTENNA CABLE
CONNECTOR
CONTROL
UNIT
FRONT
ANTENNA
CABLE
HOLE
VEHICLE
FRAME
WIRE TIE
ANTENNA
CABLE
ENGINE STARTER
HARNESS
QB51037AH
CENTER
CONSOLE
QB51039AH
24 of 30
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
84. Secure the antenna cable to the engine starter harness with one wire tie.
ANTENNA
CABLE
WIRE TIE
ENGINE
STARTER
HARNESS
86. Using isopropyl alcohol on a shop towel, thoroughly clean the hood where the caution label will attach.
Clean with isopropyl alcohol.
HOOD
CAUTION
LABEL
CENTER CONSOLE
QB51040AH
85. Bundle up the excess antenna cable, and secure it to the vehicle frame with two wire ties.
NOTE: Do not fold the antenna cable.
VEHICLE
FRAME
20 mm (0.8 in.) or above.
QB51042AH
87. Attach the caution label to the hood in the location shown.
88. Check that all wire harnesses are routed properly and all connectors are plugged in.
89. Check the overlap between the headliner and the driver’s A-pillar trim. Refer to the service manual. If necessary, adjust the overlap.
90. Reinstall all removed parts.
91. Reconnect the negative cable to the battery.
92. Press and hold the radio power button for two seconds to restore the radio and navi (if equipped) system functions.
93. Reset the clock.
94. Perform the “REMOTE ENGINE STARTER
REGISTRATION” and the “FUNCTION CHECK”.
ANTENNA
CABLE
(Bundle up the excess.)
2 WIRE
TIES
CENTER
CONSOLE
QB51041BH
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301)
25 of 30
REMOTE ENGINE STARTER REGISTRATION
1.
Acquire the PCM Code from the Interactive Network.
5.
Select Honda Systems, then click the check button.
Select
“Honda Systems.”
CAR ICON
QB00999AH
2.
Connect the HDS/MVCI tester to the OBD II data link connector, then turn the ignition switch to the on (II) position.
3.
Start the HDS, and click the car icon.
4.
Input the VIN and other required information into the
HDS, then click the check button.
CHECK BUTTON
QB32103AH
6.
Select R/C ENG STARTER and click the check button.
Select
“R/C ENG STARTER.”
CHECK BUTTON
QB32104AH
Input the VIN and other required information.
CHECK BUTTON
QB32102BH
26 of 30
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
7.
Select REGISTER REMOTE CONTROL ENGINE
STARTER UNIT, then click the check button.
Select
“REGISTER REMOTE
CONTROL ENGINE
STARTER UNIT.”
9.
Input the PCM-code, then click the check button.
NOTE: To ensure security, the PCM-code
(password) is changed everyday, so it is impossible to register the remote control engine starter if the dates of the PCM-code acquisition and registration are different. The date of the HDS/MVCI tester should also be the same.
Input the PCM-Code.
CHECK BUTTON
QB32105BH
8.
The following message will display: Obtain PCM- code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the
password. (USA) Click the check button.
“Obtain PCM-code” message.
CHECK BUTTON
QB32107BH
10. The following message will display: The registration of the Remote Control Engine
Starter Unit has been completed. Turn the ignition switch off.
“The registration of the
Remote Control Engine
Starter Unit has been completed.”
CHECK BUTTON
QB32106AH
QB32108CH
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301)
27 of 30
11. The following message will display: Check that
engine can be started by the Transmitter. Click the check button.
“Check that engine can be started by the Transmitter.”
CHECK BUTTON
QB32109CH
12. Perform the FUNCTION CHECK on page 29, then disconnect the HDS/MVCI.
28 of 30
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
FUNCTION CHECK
Operating Conditions
• The hood is closed
• The shift lever is in park
• Turn the ignition switch off and the key is outside the vehicle
• All doors and trunk lid closed and locked
Inspection
1.
Press the engine/command button on the transmitter, and release, within 2 seconds, press the lock/start button on the transmitter.
The engine should start if all operating conditions are met. (Refer to the engine starter operation.)
Does the engine start?
Yes - Operation is normal.
No:
• Make sure all “Operating Conditions” are met.
• Check the engine starter harness connections.
• Connect the HDS/MVCI and check for an indicated failure. (Refer to the appropriate Service Manual for details.)
2.
Press the engine/command button on the transmitter and release, within 2 seconds, press the unlock/stop button. The engine should stop.
Does the engine stop?
Yes - Operation is normal.
No - Check the engine starter harness connections.
ENGINE/
COMMAND
BUTTON
ENGINE START
OPERATION RECEPTION
INDICATOR
CHECKING
INDICATOR
Blinking
ENGINE
RUNNING
INDICATOR
3.
After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:
NOTE: After each test the ignition key must be cycled, or the driver’s door must be opened and closed.
• Move the shift lever out of the P position.
• Unlock or open the doors or the trunk lid.
• Open the hood.
• Press on the brake pedal.
• Press the engine start/stop button.
Does the engine stop after each of these tests?
UNLOCK/
STOP
BUTTON
*1
LOCK/
START
BUTTON
IN-CAR B127121H
TEMPERATURE
*1
REMAINING
IDLING TIME
*1 Only on vehicles equipped with the automatic climate control.
This indicator is displayed for some vehicles among them.
Yes - Operation is normal.
No - Check the engine starter harness connections.
4.
Check that the power windows and the moonroof do not function, and the shift lever does not move to any position when the engine is started with the transmitter.
5.
Check that the engine does not start under “Operating Conditions” with the key left inside the vehicle.
6.
Start the engine again, press the engine/command button on the transmitter two times, and check the vehicle condition on the display.
7.
Check the operation of the transmitter when the vehicle is 120 m (400 ft.) away and in direct sight.
© 2013 American Honda Motor Co., Inc. – All Rights Reserved.
BII 13404 (1301)
29 of 30
8.
Press the unlock/stop button on the transmitter and verify that the doors unlock. Press the lock/start button, and verify that the doors lock.
• For the vehicle equipped with the memory seat, make sure to shift the seat position of driver’s seat to “Driver 1” by unlock of transmitter.
9.
Check that the engine can start by the vehicle key and that the wiper and the headlight can be operated normally.
30 of 30
BII 13404 (1301) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
