TomTom Runner & Multi-Sport Reference Guide

TomTom Runner & Multi-Sport Reference Guide
TomTom Runner &
Multi-Sport
Reference Guide
Contents
Welcome
3
Getting started
4
Your watch
5
Using the desk dock ....................................................................................................................... 5
Using the bike mount ..................................................................................................................... 6
Watch status .................................................................................................................................. 7
Activities
9
About activities ............................................................................................................................... 9
Starting an activity.......................................................................................................................... 9
Pausing and stopping an activity .................................................................................................. 10
Settings for Cycle activities........................................................................................................... 10
Settings for Swimming activities ................................................................................................... 10
Settings for Treadmill activities ..................................................................................................... 11
Information as you train ................................................................................................................ 12
Training programs ........................................................................................................................ 14
About training programs .......................................................................................................... 14
None ....................................................................................................................................... 14
Goals ...................................................................................................................................... 14
Intervals .................................................................................................................................. 15
Laps........................................................................................................................................ 15
Zones ..................................................................................................................................... 16
Race ....................................................................................................................................... 16
Using the stopwatch ..................................................................................................................... 17
Tracking your activities ................................................................................................................. 17
Settings
19
About settings .............................................................................................................................. 19
Clock ........................................................................................................................................... 19
Sensors ....................................................................................................................................... 19
Options ........................................................................................................................................ 20
Profile .......................................................................................................................................... 20
Adding sensors
21
About sensors .............................................................................................................................. 21
Heart Rate Monitor ....................................................................................................................... 21
Cadence Sensor .......................................................................................................................... 22
TomTom MySports Connect
26
Addendum
27
Copyright notices
30
2
Welcome
This Reference Guide explains everything you need to know about your new TomTom GPS Sports
Watch.
Here are some good starting points:





Getting Started
About your watch
Starting an activity
Training programs
Settings
3
Getting started
Before you start training, it's a good idea to charge your watch, download any software updates and
download QuickGPSfix. QuickGPSfix helps your watch get a GPS fix and find your location quickly.
1. Download TomTom MySports Connect from tomtom.com/getstarted/sports and install it on your
computer. TomTom MySports Connect is available for free.
2. Place your watch in the desk dock and connect the dock to your computer.
Follow the instructions that TomTom MySports Connect gives you.
After your watch is charged, you can start your first activity.
You should connect your watch to your computer regularly to charge it, download software updates
and download QuickGPSfix information.
Battery life
When the battery is fully charged, your watch can be used for up to 10 hours of activities that need
GPS reception, such as running and cycling. The battery is used more quickly if you use the backlight
on your watch frequently or all the time, or connect the watch to sensors, such as the Heart Rate
Monitor or Cadence Sensor.
The following tips will help your watch go longer on a battery charge:


Turn off night mode and touch the screen to turn on the back light only when you need it.
Turn off sensors that you are not using. Your watch keeps searching for sensors even if you are
not using a sensor.
4
Your watch
When you use your watch, you start from the clock screen. This screen shows the time and date. The
hour number is shown slightly dimmed and the minutes are shown brighter so you can see the precise
time more clearly.
Use the button to move up, down, left or right to other screens on your watch.
1.
2.
3.
4.
5.
6.
Left - opens the Status screen.
Down - opens the Settings screen.
Right - opens the Activities screen.
Up - from the clock, moving up doesn't open another screen.
GPS receiver. While you train, the GPS receiver should face upwards.
Touch this area of the screen to turn on the back light.
The clock screen shows the time and date. You can choose to show the time in 12 hour or 24 hour
format by moving down to open the Settings screen, then selecting Clock.
Using your watch
Move up or down to select items in a menu.
Move right to select an item and open the menu for that item.
Move left to exit a menu.
To select an option in a menu, make sure it is highlighted when you leave the menu. Your watch
remembers the option you highlighted.
If an option in a menu switches on and off, move right to change the setting.
Using the desk dock
You can use the desk dock when your watch is in the wrist strap or you can remove your watch from
the wrist strap first.
5
To remove the watch from the wrist strap, hold the watch in one hand and lift the strap upwards away
from the watch. The wrist strap pops off the front of the watch.
To place your watch in the desk dock, slide the watch into the dock, following the curve of the back of
the watch.
To remove your watch from the desk dock, push underneath the screen of the watch. The watch will
slide out, following the curve of the back of the watch. Do not lift the watch from the top as this can
damage the desk dock.
Using the bike mount
Note: The bike mount is included with some products and available as an accessory for others.
The bike mount consists of a holder for your watch and a handlebar strap to attach the clip to your
handlebars.
To use the bike mount, do the following:
1. Attach the handlebar strap to the back of the holder.
2. Place the strap on your handlebar and wrap it around the bar.
3. Use the clip on the bottom of the holder to attach the handlebar strap to it.
6
The strap should now be attached securely around the handlebar.
4. Remove your watch from the wrist strap and place it in the holder. Make sure it clips securely into
place.
5. Close the handlebar strap over the top of the watch, attaching it to the top of the holder using the
clip.
Watch status
From the clock screen, move left to open the status screen.
7
The status screen shows the following information:



Battery - the battery power left on your watch.
To charge the battery, place the watch in the desk dock and connect the dock to your computer.
Storage - the amount of free space available on your watch.
If you are running out of space, connect your watch to your computer. TomTom MySports Connect
transfers the history of your activities to your computer. You can select that the history is uploaded
automatically to your account on the TomTom MySports website, or another website you have
chosen.
QuickGPS - the status of the QuickGPSfix information on your watch.
QuickGPSfix helps your watch find your precise location quickly so that you can start your activity.
To update the QuickGPSfix information on your watch, connect your watch to your computer.
TomTom MySports Connect automatically updates QuickGPSfix on your watch. QuickGPSfix information is valid for three days after you download it.
These symbols are used to show the status of QuickGPSfix:
QuickGPSfix on your watch is up-to-date.
or

QuickGPSfix on your watch is out-of-date. If the QuickGPSfix information on your watch is out-of-date, your watch still works as usual. It
may, however, take longer to get a GPS fix when you want to start an
activity.
Version - the software version number and serial number of your watch. You may need this
information if you contact Customer Support. Every time you connect your watch to your computer, TomTom MySports Connect checks if a software update is available for your watch.
8
Activities
About activities
On the activities screen, you can start one of the activities available on your watch:





Run
Cycle
Swim
Treadmill
Stopwatch
Note: Not all activities are available on all watches.
When you select Run or Cycle, your watch uses its internal GPS receiver to measure your speed, and
to record the route you have taken.
When you select Swim or Treadmill, your watch uses its internal motion sensor to measure your
strides on the treadmill, and strokes and turns in the swimming pool. Your watch uses this information
to estimate your speed and the distance you have covered.
When you select Stopwatch, you can use your watch to show elapsed time, mark laps and see times
for your current and previous laps.
Starting an activity
To start an activity on your watch, do the following.
1. From the clock, move right.
2. Select one of the activities, then move right.

Run

Cycle

Swim

Treadmill

Stopwatch
Note: Not all activities are available on all watches.
3. For Run and Cycle activities, until your watch has a GPS fix you see the message Please wait,
and the GPS icon flashes in the bottom left hand corner of the screen. When it's ready to start an
activity, your watch shows the message GO and the GPS icon stops flashing.
For Cycle activities, if you are using a cadence sensor, once your watch is connected to the sensor, your watch shows the message GO. The cadence sensor is then used to provide speed and
distance information about your activity. Your watch may not have a GPS fix at this point. If you
would like to track the route of your activity, wait until the GPS icon stops flashing before starting
your activity.
Note: It can take a short time to find your GPS position, especially the first time you use your
watch or if the QuickGPSfix information is not up-to-date. To ensure good GPS reception, make
sure you are outdoors with a clear view of the sky. Large objects such as tall buildings can sometimes interfere with reception.
9
From this screen, move in one of these directions to choose an option:

Right - start your activity, once your watch has a GPS fix.

Down - select a training program or set the information displayed while you train.

Up - see a history of your past activities.

Left - go back to the list of activities.
Move right to start your activity.
4. When you are doing an activity, your watch shows information, such as the distance, time and
pace. Move up and down to change the information that you see.
5. You can pause the activity if you're just taking a break, or stop the activity completely.
For each type of activity, you can select different training programs, and select to see different information while you are training.
Pausing and stopping an activity
During an activity, move left to stop the clock and pause your activity.
Note: If the activites screen Lock is on, you see a timer screen when you move left. Hold the button
until the timer screen has gone. Your activity is then paused or stopped. You can turn Lock on and
off in the Options settings.
To restart the activity again, move right.
To stop the activity completely, move left to pause the activity, then move left again.
Settings for Cycle activities
Note: Cycle is available on the TomTom Multi-Sport.
If you are using a cadence sensor, you should set the Wheel size setting to help increase the accuracy of the metrics provided by the sensor. This setting is the circumference of your rear tyre in millimetres (mm).
To set your wheel size, do the following:
1. From the activity start screen, move down to open the Settings screen.
2. Select Wheel size, then move right.
3. Set the size so it's correct for your rear wheel.
To find the circumference of your rear wheel, you can either measure the wheel yourself using a tape
measure, or look up the value in an online calculator. For example, on this site you can find the
circumference using the diameter of the wheel and the thickness of the tyre:
www.bikecalc.com/wheel_size_math
For example, if your wheel size is 700c and the tyres are 20 mm thick, the circumference is 2079 mm.
This is the value you should enter.
Settings for Swimming activities
Note: Swim is available on the TomTom Multi-Sport.
Before you start a swimming activity, you should check two settings:


The Pool size setting for the pool where you are swimming. This setting is the length of the pool in
metres.
The Wrist setting for the wrist you wear your watch on.
10
As you swim, your watch registers your strokes and the number of turns you make in the pool. To
calculate the distance you have swum and your speed, your watch uses the pool size and the number
of turns you have made. If the pool size is not set correctly, the metrics for your swimming activity
cannot be worked out correctly. Your watch needs to know which wrist you wear your watch on so it
can register your strokes correctly.
To change the Pool size and Wrist settings, do the following:
1.
2.
3.
4.
5.
6.
7.
From the activity start screen, move down to open the Settings screen.
Select Pool size, then move right.
Set the size so it shows the correct length for the pool.
Move left to go back to the settings menu.
Select Wrist, then move right.
Change the setting to the wrist you wear your watch, if necessary.
Move right to go immediately back to the activity screen.
When you select Swim, your watch does not use its internal GPS receiver.
Settings for Treadmill activities
Before you start an activity on the treadmill for the first time, you should set your height. You can do
this in your TomTom MySports account or on your watch.
As you run on a treadmill, your watch registers the number of times you swing your arm back and
forward and how quickly. This matches the number of strides you make as you run. Your watch uses
your height to calculate the length of your stride, and from this the distance you have run and your
pace.
To set your height on your watch, do the following:
1.
2.
3.
4.
From the clock, move down to open the Settings screen.
Select Profile, then move right.
Select Height, then move right.
Set your height.
Calibrating your watch for Treadmill activities
The distance measurements your watch makes for Treadmill activities is less accurate than for Run
activities. When you run outdoors, your watch uses GPS to measure the distance you cover.
If you calibrate your watch, the distance measurements for Treadmill activities become more accurate.
To calibrate your watch, do the following:
1. During your first Treadmill activity, after you have run for a short time, pause your watch and the
treadmill.
To pause your watch, move left during the activity.
2. On your watch, move down to open the Settings menu.
3. Select Calibrate then move right.
4. Change the distance to match the distance shown on the treadmill.
5. Move right to go immediately back to the activity screen.
Calibrating your watch at the end of a Treadmill activity
Every time you finish a Treadmill activity, your watch asks you if you want to calibrate the distance
measurement your watch has made with the distance measurement shown by the treadmill.
Select Yes to calibrate the distances. If you calibrate the distance, your activity record is more accurate and the metrics for your training are more accurate.
11
Information as you train
While you train, three different metrics are available at any one time:


One main metric is shown in a larger figure in the main part of the screen.
Two minor metrics are shown in smaller figures at the top of the screen.
All metrics relate to your current activity.
Some examples of metrics available:










Duration - the length of time spent on your current activity.
Distance - the distance covered in your current activity.
Pace - your current pace.
Average pace - your average pace for the current activity.
Lap time - the length of time taken for the current lap.
Lap distance - the distance covered in the current lap.
Ascent - the total you have climbed while cycling. This metric is only available if you watch has a
built-in barometric sensor.
Gradient - the degree of slope of the ground on which you are cycling. This metric is only available
if you watch has a built-in barometric sensor.
Heart rate - your heart rate. This metric is only available if you have a Heart Rate Monitor connected.
SWOLF - this metric is only given for swimming activities. The SWOLF score is calculated by
adding the time in seconds and the number of strokes you make to swim one length of the pool.
SWOLF shows your swimming efficiency. The lower the score, the better. The word SWOLF is a
mixture of swimming and golf.
Changing the main metric
As you train, you can change the information shown by the larger figure by moving up and down. The
text underneath the main metric shows which information is currently being displayed.
The metrics that are available depend on your current activity.
Setting the minor metrics
For each activity, do the following to choose the information shown by the smaller figures:
1.
2.
3.
4.
From the activity start screen, move down to the Settings menu.
Select Display, then move right.
Select Left or Right to set the metric shown on the left or the right.
Select the metric to be displayed from the list.
The metrics that are available depend on your current activity.
Icons on the screen
The following icons can be shown along the bottom of the screen while you are training:
12
This symbol shows the strength of GPS reception. While your watch is
looking for GPS satellites, the satellite images flashes.
The heart symbol shows that your watch is connected to a Heart Rate
Monitor. When your watch is trying to connect to the Heart Rate Monitor, the
heart flashes.
The chainring symbol shows that your watch is connected to a Cadence
Sensor. When your watch is trying to connect to the Cadence Sensor, the
chainring flashes.
This symbol shows the battery status.
13
Training programs
About training programs
For each type of activity, the following training programs are available:






None
Goals
Intervals
Laps
Zones
Race
From the clock screen, do the following see the list of training programs:
1.
2.
3.
4.
Move right and then select your choice of activity.
Move right.
Move down and select Training.
Move right and choose a training program.
When you select a training program, your watch remembers which program you are using and any
options you have selected for that program.
Tip: If you want to start a program immediately after selecting it, move right to go straight to the
activity screen.
None
Select this option to do your activity without using a training program. In this mode, your watch records
your activity and shows metrics for your activity.
Goals
Select this option to set yourself training goals.
You can set yourself three types of goals:



Distance - select this option to set yourself a distance to cover in your activity.
Time - select this option to set yourself a duration for your activity.
Calories - select this option to set yourself a number of calories to burn during your activity. The
calories burnt can be calculated more accurately if you set your profile.
Watching your progress
To see an overview of your progress towards your goal, move right from the activity progress screen.
This screen shows the percentage of your target you have reached and the remaining distance, time
or number of calories.
14
Progress alerts
When training to a goal, your watch alerts you at these stages:




50%
90%
100%
110%
Intervals
Select this option to use interval training.
Interval training is short periods of exercise followed by rest. The main aim of interval training is to
improve speed and cardiovascular fitness. For example, during a 20 minute walk-jog workout you
could do an 8 minute fast walk, followed by 3 sets of 1 minute running and 2 minutes walking, then a 5
minute walk to cool down.
For warmup, work, rest and cooldown, you can set either a time or a distance. For sets, you choose
the number of sets you want to include in your interval training program.
Tip: If you move right after setting the warmup details, you are then in the right place to setup the
rest of that interval set including work, rest etc.
When setting up interval training using zones, you can choose between sprint, speed, fat burn and
recover for the work section of the set.
During interval training, you see an alert for the next stage of interval training:
You see the number of the current set, the name of what you are doing, and how long this part of the
set is in minutes.
You are also warned with beeps and buzzes when you need to switch to the next stage in your interval
training.
Laps
Select this option to measure your activity against set lap times, distances or by manually recording
when you complete a lap.
You can set up your watch to measure laps in three ways:


Time - select this option to set a duration for a lap. After you start your activity, your watch alerts
you when the time for each lap passes. If you set a lap time of 1 minute, your watch alerts you
each minute and the screen shows the number of laps completed.
Distance - select this option to set the length of a lap. After you start your activity, your watch
alerts you whenever you reach the target distance for one lap. If you set a lap distance of 400 m,
your watch alerts you after each 400 m you cover and the screen shows the number of laps completed.
15

Manual - select this option to record yourself when you complete a lap. To mark the end of a lap,
touch the right side of the watch screen, in the same place you touch to show the back light.
Your watch shows the number of laps completed and alerts you that a lap is complete.
Zones
Select this option to train within a target zone.
You can select from the following training zones, depending on the activity:




Pace - select this option to set your target time per mile or kilometre. You can set your target time
and a margin above and below the target that you allow yourself.
Speed - select this option to set your target speed and a margin above and below the target that
you allow yourself.
Heart - select this option to set your target heart rate. For your watch to be able to measure your
heart rate, it must be connected to a Heart Rate Monitor. You can set your target heart rate and a
margin above and below the target that you allow yourself.
Cadence - select this option to set your target cadence for your cycling activity. For your watch to
be able to track your cadence, it must be connected to a Cadence Sensor. You can set your target
cadence and a margin above and below the target that you allow yourself. Not all watches are
able to connect to a cadence sensor.
Monitoring your progress
From the activity progress screen, move right to see a graphical overview of how close your training is
to the zone you set. The graph shows if you are above or below your target zone and by how much,
throughout your activity.
You regularly receive alerts to tell you if you are in your zone or outside your zone:


If you are outside your training zone, an alert is played and the screen shows if you are above or
below your zone.
If you are in your training zone, an alert is played and the screen shows a target symbol.
Race
Select this option to race against one of your ten most recent activities or a predefined activity from the
MySports website. The predefined activities from MySports consist of a distance and a time.
When you use the Race training program, you can see if you are ahead or behind in the race and by
how much, as you train.
16
From the activity progress screen, move right to see a representation of the race. The distance at the
top of the screen shows the remaining distance in the race, and the distance at the bottom shows how
much you are ahead or behind.
Your watch alerts you so you know if you are in front or behind in your race.
Using the stopwatch
To use the stopwatch, do the following.
1. From the clock, move right.
2. Select Stopwatch, then move right.
Your watch shows an image of a stopwatch and the word "GO".
3. Move right to start the stopwatch.
The stopwatch starts and shows the elapsed time.
4. To pause the stopwatch, move left. Move right to resume counting.
5. To mark each lap, touch the right side of the watch screen while the stopwatch is running, or move
right.
Your current lap time, for example lap 12 below, is shown under the elapsed time and your previous laps, here laps 11 and 10 are shown under your current lap.
To see more of your previous laps, move down and move up.
6. To leave the stopwatch activity, move left two times.
Tip: The stopwatch does not run in the background after you leave the stopwatch activity.
Tip: To reset the stopwatch, leave the stopwatch activity and then go back into it again.
Tracking your activities
Whenever you train, your activity is logged by your watch for that type of activity. To see the history of
your training for each type of activity on your watch, do the following:
1. From the activity start screen, move up to open the History for that type of activity.
2. From the list, select the activity you want to look at. The list shows the date and time you started the activity.
3. Move right.
17
Some basic information about the activity is shown. The information available depends on the activity.
Transferring your activities to TomTom MySports
Connect your watch to your computer to transfer details of your activities to TomTom MySports or
another sports website that you choose, using TomTom MySports Connect. You can also transfer
details about the activity to your computer in several different file formats.
18
Settings
About settings
From the clock screen, move down to open the Settings screen. These settings determine the overall
behaviour of your watch. For each activity, there are also settings related to that activity.
The following settings are available for your watch:




Clock
Sensors
Options
Profile
These settings are available for activities:



Settings for Cycle activities
Settings for Swim activities
Settings for Treadmill activities
Clock
From the clock screen, move down to open the Settings screen, then select Clock and move right to
open the Clock menu.
Alarm
Select Alarm to turn the alarm on and off and to set the alarm time.
When the alarm goes off, you can choose to stop it or snooze. If you snooze the alarm, it goes off
again in 9 minutes.
Time
Select Time to set the time on your watch. The time is either set using the 12 or 24 hour clock,
depending on the setting for 24HR.
Date
Select Date to set the date on your watch.
24HR
Select 24HR to switch between using the 12 hour clock and the 24 hour clock to display and set the
time. Move right to switch between ON and OFF for this setting.
Sensors
From the clock screen move down to open the Settings screen, then select Sensors and move right
to open the Sensors menu.
You can turn on and off two types of sensors:


Heart - this is a heart rate monitor.
Bike - this is a cadence sensor.
Tip: To help your watch go longer on a battery charge, turn off sensors that you are not using. Your
watch keeps searching for sensors even if you are not using a sensor.
19
Options
From the clock screen, move down to open the Settings screen, then select Options and move right
to open the Options menu.
Units
Select Units to set the distance and weight units used on your watch. You can select any combination
of miles or kilometres, and pounds or kilogrammes.
Click
Select Click to set what your watch does as you move through menus. Your watch can do the following:


Make a clicking sound.
Vibrate/buzz for short time.
You can turn both on or off, or turn only one on.
Demo
Select Demo to turn the demo mode on and off. In demo mode, your watch behaves as if it has a GPS
fix and you are training, even if you are not. Any activities completed in demo mode are not added to
your history of activities.
Night
Select Night to turn the night mode on or off. If the night mode is on, the backlight comes on and stays
on during an activity. When you stop the activity, the light goes off again.
Note: The battery will run down much more quickly than normal if you use the night mode while
training.
Lock
Select Lock to turn the activity lock function on and off. The lock function prevents your current activity
being paused or stopped if you accidentally move left.
Profile
From the clock screen on your watch, move down to open the Settings screen, then select Profile
and move right to open the Profile menu.
Select the following options to set your details in each case:




Weight
Height
Age
Gender
Information from your profile is used for the following:



To work out the number of calories you burn during an activity.
To set the target heart rates for you in the heart rate training zones. The zones are worked out by
your TomTom MySports account.
To work out your stride length if you are training on a treadmill.
Language
Select Language to set the language used for menus and messages on your watch.
20
Adding sensors
About sensors
Sensors are external devices which you can link to your watch to provide information about your
activity. Two types of sensors can be used with your watch:


Heart rate monitor - this measures your heart rate as you train. The TomTom Heart Rate Monitor
is included in some products and available as an accessory for others.
Cadence sensor - this measures your cadence as you cycle. The TomTom Cadence Sensor is
included in some products and available as an accessory for others. TomTom Runner does not
support the Cadence Sensor.
Cadence
Cadence measures the speed at which you pedal in revolutions per minute (rpm). In a low gear, you
may have a very high cadence but a lower speed. In a high gear, you may have a low cadence but a
higher speed. Cyclists train to find the balance between cadence and speed which allows them to
cycle as efficiently as possible.
Heart Rate Monitor
To use the TomTom Heart Rate Monitor with your watch, do the following:
1. Attach the monitor to the strap.
2. Attach the strap around your chest, so the monitor sits just above the base of your chest bone.
Make sure the monitor is the right way up so that the word 'TomTom' is the right way up for
someone standing in front of you.
Tip: Wet the contact areas on the inside of the strap before placing it around your chest. This
makes it easier for the monitor to pick up your heartbeat.
3. From the clock screen on your watch, move down.
4. Select Sensors then move right.
21
5. Select Heart, then move right to turn it on.
6. When you begin an activity, your watch connects to the monitor and you see a heart icon at the
bottom of the screen.
When your watch is trying to connect to the monitor, the heart flashes.
The first time your watch tries to connect to your monitor, if it finds more than one monitor, your
watch doesn't know which monitor to connect to. Move to a place where there are no other monitors within range of your watch.
When you have connected to your monitor once, your watch always reconnects to your monitor.
While you train, you can choose to show your heart rate.
You can also use a training program to train to a target heart rate zone.
You can also use the Heart Rate Monitor with other Bluetooth® Smart Ready devices and apps. See
the documentation that comes with your product or app for more information.
To change the CR2032 battery on the monitor, use a coin to open the back of the monitor. The battery
must be recycled or disposed of according to local laws and regulations.
Cadence Sensor
The TomTom Cadence Sensor consists of the following parts:
1.
2.
3.
4.
Spoke magnet
Crankarm magnet
Chainstay sensor
Cable ties
To use the TomTom Cadence Sensor with your watch, do the following:
1. Attach the chainstay sensor to the chainstay on your bike, using three of the cable ties provided.
Use two ties for the main body of the sensor and one tie for the smaller part of the sensor. You
may need to adjust the position of the sensors so don't tighten the ties completely just yet.
22
Important: The smaller part of the sensor needs to face the crankarms and should not be attached to the top of the chainstay. You may have to tilt the main body of the sensor towards the
wheel depending on your bike. You should make this adjustment after you have attached the
spoke magnet.
2. Attach the spoke magnet to one of the spokes on your bike. The magnet should face the chainstay
where you attached the chainstay sensor.
3. Adjust the position of the spoke magnet and the chainstay sensor so that when the wheel turns,
the spoke magnet passes the tip of the main body of the chainstay sensor.
Important: The distance between the chainstay sensor and the spoke magnet should not be
more than 2 mm when they pass each other. On some bikes, you may have to tilt the main body
of the sensor towards the wheel.
23
4. Attach the crankarm magnet to one of the crankarms on your bike. The magnet should face the
chainstay where you attached the chainstay sensor.
Tip: Make sure the different parts of the Cadence Sensor are lined up correctly on your bike. The
spoke magnet should pass the main body of the chainstay sensor and the crankarm magnet
should pass the tip of the sensor.
5.
6.
7.
8.
9.
10.
Once you have adjusted the sensors to the right position, tighten the cable ties so they are held
securely in place.
On your watch, set the wheel size to help increase the accuracy of the metrics provided by the
sensor. The wheel size is the circumference of your tyre in millimetres (mm).
Move your bike or its crankarm so that at least one of the magnets passes the sensor. This
switches on the sensor.
From the clock screen, move down.
Select Sensors, then move right.
Select Bike, then move right to turn it on.
When you begin a workout, your watch connects to the sensor and you see an icon of a chainring
at the bottom of the screen.
When your watch is trying to connect to the Cadence Sensor, the chainring flashes.
The first time your watch tries to connect to your sensor, if it finds more than one sensor, your
watch doesn't know which sensor to connect to. Move to a place where there are no other sensors
within range of your watch.
24
When you have connected to your sensor once, your watch always reconnects to your sensor.
When the chainring icon has stopped flashing, your watch is ready to measure your speed and
cadence. For proper GPS tracking, wait until the GPS icon has also stopped flashing before you
start your cycle activity.
While you train, you can choose to show your current cadence or change the display to see your
cadence.
You can also use a training program to train to a target cadence zone.
You can also use the Cadence Sensor with other Bluetooth® Smart Ready devices and apps. See the
documentation that comes with your product or app for more information.
To change the CR2032 battery on the sensor, use a coin to open the back of the sensor. The battery
must be recycled or disposed of properly according to local laws and regulations.
25
TomTom MySports Connect
TomTom MySports Connect does the following:





Helps you set up your watch.
Updates the software on your watch when new versions become available.
Transfers your activity information to your TomTom MySports account or another sports website
that you choose. TomTom MySports Connect can also transfer activity information to your computer in a number of file formats.
Transfers any settings you make on TomTom MySports to your watch.
Updates the QuickGPSfix information on your watch.
Installing TomTom MySports Connect
You can download TomTom MySports Connect for free from here: tomtom.com/getstarted/sports
Once installed, connect your watch to your computer using the desk dock.
TomTom MySports account
If you transfer your activities to a TomTom MySports account, you can store, analyse and view the
history of your activities. You can view the routes you have taken and all the metrics associated with
your activities.
To create an account, click the button in TomTom MySports Connect, or go directly to the website:
mysports.tomtom.com
You can also choose to transfer your activities to your account on other sports websites.
26
Addendum
Warning
Always consult a physician before starting an exercise program. If you have a pacemaker or other
implanted electronic device, consult your physician before using this product.
The use of this product while exercising might distract from your surroundings or your activity.
How TomTom uses your information
Information regarding the use of personal information can be found at tomtom.com/privacy.
Battery and Environmental information
This product uses a lithium polymer battery that is not user accessible or user replaceable. Do not
open the case or (attempt to) remove the battery. Substances in the product and/or battery may be
harmful to the environment or your health if disposed of improperly. The battery contained in the
product must be recycled or disposed of properly according to the local laws and regulations and
always kept separate from household waste.
WEEE directive
The wheelie bin symbol on the product or its packaging indicates that this product shall not be treated
as household waste. In line with EU Directive 2002/96/EC for waste electrical and electronic equipment (WEEE), this electrical product must not be disposed of as unsorted municipal waste. Please
dispose of this product by returning it to the point of sale or to your local municipal collection point for
recycling. By doing this you will help conserve the environment.
Battery operating temperatures
Operating temperatures: -20°C (-4°F) to 60°C (140°F). Do not expose to temperatures beyond this.
R&TTE directive
Hereby, TomTom declares that TomTom products and accessories are in compliance with the essential requirements and other relevant provisions of the EU Directive 1999/5/EC. The declaration of
conformity can be found here: tomtom.com/legal.
27
FCC information for the user
THE DEVICE COMPLIES WITH PART 15 OF THE FCC RULES
Federal Communications Commission (FCC) Statement
This equipment radiates radio frequency energy and if not used properly - that is, in strict accordance
with the instructions in this manual - may cause interference to radio communications and television
reception.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference
and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:




Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
FCC ID: S4L8RS00
IC ID: 5767A-8RS00
FCC RF Radiation Exposure Statement
The transmitters within this device must not be co-located or operating in conjunction with any other
antenna or transmitter.
Responsible party in North America
TomTom, Inc., 150 Baker Avenue Extension, Concord, MA 01742
Tel: 866 486-6866 option 1 (1-866-4-TomTom)
Emissions information for Canada
Operation is subject to the following two conditions:


This device may not cause interference.
This device must accept any interference, including interference that may cause undesired
operation of the device.
Operation is subject to the condition that this device does not cause harmful interference.
This Class B digital apparatus complies with Canadian ICES-003. CAN ICES-3(B)/NMB-3(B).
IMPORTANT NOTE
IC Radiation Exposure Statement:
28


This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This device and its antenna(s) must not be co-located or operating in conjunction with any
other antenna or transmitter.
C-tick
N14644
This product displays the C-tick to show it complies with relevant Australian regulations.
Notice for New Zealand
This product displays supplier code Z1230 to show it complies with relevant New Zealand regulations.
Customer support contact
Australia: 1300 135 604
New Zealand: 0800 450 973
Model names
8RS00
29
Copyright notices
© 2013 TomTom. All rights reserved. TomTom and the "two hands" logo are registered trademarks of
TomTom N.V. or one of its subsidiaries. Please see tomtom.com/legal for limited warranty and end
user licence agreements applying to this product.
Linotype, Frutiger and Univers are trademarks of Linotype GmbH registered in the U.S. Patent and
Trademark Office and may be registered in certain other jurisdictions.
MHei is a trademark of The Monotype Corporation and may be registered in certain jurisdictions.
AES code
The software included in this product contains AES code under Copyright (c) 1998-2008, Brian
Gladman, Worcester, UK. All rights reserved.
Licence terms:
The redistribution and use of this software (with or without changes) is allowed without the payment of
fees or royalties provided that the following conditions are adhered to:
Source code distributions include the above copyright notice, this list of conditions and the following
disclaimer.
Binary distributions include the above copyright notice, this list of conditions and the following disclaimer in their documentation.
The name of the copyright holder is not used to endorse products built using this software without
specific written permission.
Calorie calculations
Calorie calculations in this products are based on MET values from:
Ainsworth BE, Haskell WL, Herrmann SD, Meckes N, Bassett Jr DR, Tudor-Locke C, Greer JL, Vezina
J, Whitt-Glover MC, Leon AS. 2011 Compendium of Physical Activities: a second update of codes and
MET values. Medicine and Science in Sports and Exercise, 2011;43(8):1575-1581.
30
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement