Operating Instructions C00169 Hand Tool 1. Band may be used from bulk roll as this completely eliminates waste of band. Slide buckle on band as shown, bringing end of band around object to be clamped and again through buckle. NOTE: The tension screw thread should be lubricated regularly. 2. Continue band around object once more and again through buckle. Double banding develops a great deal more radial compression than single banding. Bend end of band under buckle. 4. Place finger on BAND-IT Band at buckle bridge while tensioning with tool handle. When you feel BAND-IT Band stop moving through buckle as you are turning handle, maximum pressure is being exerted by the BAND-IT Band around object being clamped. Stop turning handle. 5. Roll tool over buckle, backing off with tension handle throughout entire rolling operation. Failure to back off with tension handle through-out entire course of roll-over may result in breaking of band. There is no loss of tension as band released is used up in the bend. 7. Remove tool, holding stub of band down with thumb. BAND-IT-IDEX, Inc. A Unit of IDEX Corporation 4799 Dahlia Street Denver, CO 80216-3070 USA P: 1-800-525-0758 F: 1-800-624-3925 www.BAND-IT-IDEX.com Page 1 of 4 3. Place band in opening of tool nose and gripper block. Move into slot as far as possible, to avoid buckle sliding into tool nose. Tighten band clamp by turning the tension handle clockwise while holding band gripper tight against band. NOTE: The spring load of the band gripper is not intended to secure and prevent band from slipping during tension process. 6. Pull cutting handle to cut the band. 8. Hammer down buckle ears to hold band stub in place to complete BANDIT clamp. Document # P05886 rev. G © Copyright BAND-IT-IDEX, Inc. 2012 All rights reserved Cleaning and Accessories C00169 Hand Tool Gripper Cleaning Instructions: 1. Remove gripper. Align gripper pin hole with notch in tool frame. Using a punch and hammer, punch pin out of slide block. 2. Using a wire brush, clean all foreign matter from teeth. 3. Replace pin. Gripper spring must be seated in tension screw hole. Align gripper hole with slide block hole, insert pin in hole and hammer pin in place. Scru-Lokt Buckles: 1. The BAND-IT Scru-Lokt clamp, using the Scru-Lokt buckle, is applied in exactly the same way as the BAND-IT clamp except that the tool is not rolled over. 2. After tension is applied, insert set screw in Scru-Lokt buckle and tighten. To permit taking up Scru-Lokt clamp, or to re-use, a 3 inch (7.5 cm) stub should be left so that tool will be able to re-grip band later. 3. Where stub of band is left for Scru-Lokt clamp, it may be folded under as shown. Tool Accessories: JR Adapters: The JR adapters (J00169 and J05069 heavy duty) are used with the BAND-IT C00169 tool when BAND-IT JR. preformed clamps are used. C04388 Close Quarter Tension Nut: In cramped quarters, use instead of tool tension handle. NOTE: See general catalog or web site for instructions and ordering information. BAND-IT-IDEX, Inc. A Unit of IDEX Corporation 4799 Dahlia Street Denver, CO 80216-3070 USA P: 1-800-525-0758 F: 1-800-624-3925 www.BAND-IT-IDEX.com Page 2 of 4 Document # P05886 rev. G © Copyright BAND-IT-IDEX, Inc. 2012 All rights reserved Tool Assembly Parts List C00169 Hand Tool EXTERNAL RETAINING RING VINYL GRIP GRIPPER SPRING SPIN GRIP TENSION HANDLE CUTTER BAR HANDLE SET SCREW (On far side) SCREW RETAINING RING TOOL FRAME CUTTER BAR TENSION SCREW GROOVE LOCK PIN THRUST BEARING BAND GRIPPER SLIDE BLOCK EXTERNAL RETAINING RING 1 SEE SHEET 4 FOR REPAIR PART NUMBERS 1. To assist in removing threaded parts, apply heat (softens locking compound). 2. When connecting the tension screw to the slide block, clean threads (male and female) of foreign matter, then apply two drops of medium strength locking compound (Loctite 242 or equiv.) onto male threads and connect parts together. Apply .03 oz. of food-grade white lubricant or equiv. to tension screw thread. 3. When connecting the set screw to the cutter bar, clean threads (male and female) of foreign matter, then apply one drop of medium strength locking compound (Loctite 242 or equiv.) onto male thread and connect parts together. 4. Kit # C00689 contains the Tension Handle Assembly and the Tension Screw. Both parts should be changed as a set to reduce accelerated wear. Review note 2. 5. Kit # C01899 contains the Band Gripper, Gripper Spring and Groove Lock Pin. Replace all parts as a new set to maximize tool performance. Periodic cleaning of band gripper teeth will improve tool performance. 6. Kit # C02499 contains the Slide Block, Groove Lock Pin, Band Gripper, Gripper Spring, and Tension Screw. Periodic cleaning of band gripper teeth will improve tool performance. Review note 2. BAND-IT-IDEX, Inc. A Unit of IDEX Corporation 4799 Dahlia Street Denver, CO 80216-3070 USA P: 1-800-525-0758 F: 1-800-624-3925 www.BAND-IT-IDEX.com Page 3 of 4 Document # P05886 rev. G © Copyright BAND-IT-IDEX, Inc. 2012 All rights reserved Parts List and Warranty C00169 Hand Tool REPAIR PARTS LIST FOR C00169 PART # DESCRIPTION C01140 TOOL FRAME C01687 THRUST BEARING SLIDE BLOCK ASSEMBLY C02499 C01899 INCLUDES: SLIDE BLOCK, PIN, BAND GRIPPER, SPRING, TENSION SCREW. KIT, GRIPPER ASSEMBLY INCLUDES: GRIPPER, PIN, AND GRIPPER SPRING KIT, CUTTER BAR ASSEMBLY C05887 C00689 INCLUDES: CUTTER BAR HANDLE, VINYL GRIP, SET SCREW, AND CUTTER BAR KIT, TENSION HANDLE AND SCREW Refer to website for warranty information: http://www.band-it-idex.com/warranty.html BAND-IT-IDEX, Inc. A Unit of IDEX Corporation 4799 Dahlia Street Denver, CO 80216-3070 USA P: 1-800-525-0758 F: 1-800-624-3925 www.BAND-IT-IDEX.com Page 4 of 4 Document # P05886 rev. G © Copyright BAND-IT-IDEX, Inc. 2012 All rights reserved
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021