CE Labs | MP50A | Specifications | CE Labs MP50A Specifications

CE Labs MP50A Specifications
Section
7
AUDIO/VIDEO
Audio/Video
Distribution
MCM
Custom Audio . . . 113~115
Mounting Hardware . . . 128
Multiswitches . . . 130, 131
Muxlabs . . . . . . . 108~112
RF Modulators . . . . . . 117
Signal
Amplifiers . . 118, 119, 122
Splitters . . . . . . . 119~122
Antennas . . . . . . 123~126
Antennas Direct . 124, 126
Baluns . . . . . . . . 108~115
CE Labs . . . . 112, 115, 116
Channel Master . .122, 126
DirecTV . . . . . . . 127, 130
HDMI
Distribution . 108, 113, 116
HDMI Switching . . . . . 116
LNB's . . . . . . . . 130, 131
7
NEW!
NEW!
Active HDMI
Extender Balun II Kit
These items allow HDMI equipment to be connected
at distances up to 300' via two Cat5e/6 cables with
up to 1080i resolution, or 1080p deep color up to 150'.
It is ideal for digital signage, residential, boardroom,
classroom, and medical imaging video systems.
Complete kit includes transmitter, receiver and power
supply, IR target and emitter. Items sold individually
to support use with other components and hubs.
Order #
33-11445
33-11450
33-11455
33-11480
33-11485
Mfr. #
500405
500406
500407
500998
500999
Type
Complete kit
Transmitter
Receiver
IR emitter
IR receiver
(1–3)
(4–up)
$645.00 $612.00
225.00 214.00
399.00 379.00
12.49
11.89
21.19
19.99
HDMI 1.3 Balun Set
with IR Support
ONLY
$535.00
Component Video
Wall Plate Balun
NEW!
Interchangeable with 500052 and
500053 baluns, this model fits in a
single gang box and is compatible
with decora style wall plates. Sends
Y/Pb/Pr component video and one
channel of analog audio over
standard CAT5e/6 cable. Maximum
range is 1,000' for 480i, 500' for
1080i. •Mfr. #500053-WP-US
•Used in pairs, sold individually
Order #
33-11510
The HDMI 3 x 1 switcher kit allows up to three
different HDMI sources to be connected to one HDMI
display via two Cat 5e unshielded twisted-pair cables in
a point-to-point configuration. Push-button input
selection is located on the receiver unit. The kit
includes one transmitter and one receiver, and supports
up to 100' (30m) at 1080p via Cat 5e cable (supports
deep color up to 1080i). Mfr. #500410.
Order #
33-10580
ONLY
$419.00
NEW!
HDMI Extender Kit
The VideoEase Econo
Plus extender kit allows
HDMI equipment to be connected up
to 150' via two Cat5e unshielded twisted pair cables at
1080p resolution, and supports 1080p deep color up to
90' via dual Cat6 cable. Transmission lengths: •1080p:
150' via dual Cat5e, 200' via dual Cat6 •1080i/720p: 200'
via dual Cat5e, 250' via dual Cat6 •Mfr. #500401
Order #
33-10576
Includes everything you need to connect HDMI
equipment at distances up to 330' at 1080p deep color
via a single CAT5e/6 cable, and also receives and
transmits an IR signal Kit includes: •Transmitter,
receiver, 12VDC power supplies, IR emitter and IR
receiver •Mfr. #500450
Order #
33-11250
HDMI 3 x 1 Switcher
and Extension Kit
ONLY
$265.00
NEW!
VideoEase™ Component
Video /IR Pass-Thru Balun
These baluns send Y/Pb/Pr component video signals
over Cat5e/6 cable up to 500' for 1080i and 1000' for
480p. Additionally, screw terminal connections are
provided, allowing access to one Cat5 pair for passing
IR signals. Models are available with female RCA
connectors, or male RCA's on 6" pigtails. •Baluns
must be used in pairs and are sold individually
Order #
33-11370
33-11375
Mfr. #
500054
500055
Type
(1–3) (4–up)
Female RCAs
$69.29 $65.89
Male RCA pigtails 69.29 65.89
ONLY
$89.99
NEW!
VideoEase™ HDTV Component
Video/Digital Audio Balun
Order #
33-10060
33-10061
33-10062
33-10063
Mfr. #
500050
500051
500052
500053
Connectors
Male RCA Female RCA
Male RCA
Female RCA
NEW!
Component Video
plus Audio Wall Plate Balun
Identical to and interchangeable with
model 500058 balun, this model fits
in a single gang box and is
compatible with decora style wall
plates. Sends Y/Pb/Pr component
video plus two channels of line level
audio over standard CAT5e/6 cable.
Maximum range is 1,000' for 480i,
500' for 1080i. •Mfr. #500058-WP-US
•Used in pairs, sold individually
Order #
33-11515
108
ONLY
$135.00
VideoEase™
Component/Composite Video Balun
These baluns send Y/Pb/Pr component video, plus one
composite video signal over Cat5e/6 cable up to 500'
for 1080i and 1000' for 480p. It is ideal when multiple
video sources, such as a digital cable box and old style
video game, are located remotely from the viewing
monitor. Models are available with female RCA
connectors, or male RCA's on 6" pigtails. •Baluns
must be used in pairs and are sold individually
Order #
33-11380
33-11385
Mfr. #
500056
500057
Type
(1–3) (4–up)
Male RCA pigtails $69.29 $65.89
Female RCAs
69.29 65.89
www.MCMelectronics.com /1-800-543-4330
Back
The component video/audio balun allows one
component video (YPbPr or RGB) signal and one
audio signal to be transmitted via cost-effective
unshielded twisted pair (UTP) cable in a point-to-point
configuration. Used in pairs, the component digital
balun supports 480i/p, 720p and 1080i/p video formats
for hi-definition (HDTV) video applications. Features:
•Supports 480i/p up to 1000' (305m) and 720p/1080i/p
up to 500' (152m) via Cat 5 UTP, respectively •Available
with color-coded RCA cable connectors •Supports
either digital audio (5000050, or 500051), or analog
audio (500052, or 500053) on fourth twisted pair
•Modular shielded RJ-45 connector
•Used in pairs, sold separately
Audio
Digital
Digital
Analog
Analog
ONLY
$79.99
79.99
79.99
79.99
VideoEase™
Audio Balun
The VideoEase™
Audio Balun
allows any
unbalanced
analog audio signal to be transmitted via a single
unshielded twisted pair (UTP) cable for more versatile
cabling. One or two pair of baluns are required
depending on whether the application is for monaural
or stereo audio. •Up to 5000' (1.5km) via Cat 5 UTP
•20~20KHz bandwidth
Order #
33-9745
ONLY
$27.99
Follow us on:
&
AUDIO/VIDEO
Audio/Video
Distribution
Receiver
Transmitter
Section
7
A
Back
VideoEase™ VGA Balun II Over UTP
VideoEase™ VGA Balun II is a passive device that fully
supports VGA and SVGA (RGBHV) transmission via
one Cat 5 UTP cable without the need for shielded
twisted pair (STP) cable. This breakthrough technology
allows VGA equipment to be deployed more easily in
both new and pre-wire structured cabling environments.
Used in pairs, sold individually.
Order #
33-9601
33-9602
33-9603
33-11355
Description
PC side (HD15-male)
Monitor side (HD15-female)
Monitor side (HD15-male)
PC side (HD15-female)
Mfr. #
ONLY
500040 $79.99
500041 79.99
500042 79.99
500043 68.99
Interchangeable with VGA balun
models 500040/41/42/43, these
units fit in a single gang box and
are compatible with decora style
wall plates. Sends VGA video
over standard CAT5e/6 cable at
distances up to 350'. •Baluns must
be used in a pair consisting of
one PC side, and one monitor
side balun.
Order #
33-11495
33-11500
Mfr. #
500041-WP-US
500043-WP-US
Type
Monitor side
PC side
Type
(1–3)
Complete kit $699.00
IR emitter
12.49
IR sensor
21.19
(4–up)
–
$11.89
19.99
VGA and Audio Balun
This active VGA/Audio balun allows VGA and stereo
or digital audio to be transmitted via CAT5e/CAT6
cable. The product also supports RS232, is DDC
compliant and supports IR source control. Features:
•Transmits signal up to 600' @ 1920 x 1200 •Supports
analog stereo or coaxial digital audio •Supports RS232
or IR control •Brightness, sharpness and skew
adjustments •Local VGA/Audio output
•Ground loop isolation
Fig.
A
B
Order #
33-11220
33-11221
Mfr. #
500146
500147
Description
Transmitter
Receiver
ONLY
$339.00
425.00
NEW!
ONLY
$89.99
89.99
Videoease PS/2 Convertor Balun
•Allows PS/2 devices to be located
up to 350' away from the PC •Using
inexpensive 4-pair Cat 5 shielded twisted pair or
unshielded twisted pair cable depending on the
equipment used •Used in pairs, eliminates the need for a
local keyboard and mouse •Typical applications include
corporate projection systems, classroom video
instruction and video information systems
•Mfr. #500045
Order #
33-10105
Mfr. #
500145
500998
500999
NEW!
Videoease Active VGA Balun Kit
•Extends the distance between the computer system
unit and a remote display monitor by up to 480'
•It accomplishes this by means of a local transmitting
unit, and remote receiving unit, connected by standard
Cat 5 twisted pair ethernet cable Features: •Uses Cat 5
ethernet cable: For economy; easy installation; and
utmost data transfer reliability •High-resolution video:
Up to 1800 x 1440 at 100 meters •Supports VGA and
SVGA monitors •Long distance transmission, up to
160m (480') •Local unit includes port for local monitor
•Mfr. #500035
Order #
33-10120
ONLY
$309.00
ONLY
$27.99
VGA 4 x 1 Switcher
Compact switcher allows a single display to select
from up to four VGA sources, when Muxlab baluns
are utilized, At the Cat 5e/6 cable. It operates in
conjunction with Model 500140 active balun kit,
and Model 500141 transmitter. At least one 500140 is
required to support one source and one display, then
up to three additional 500141 transmitters may be
added. Features: •Auto and Manual switching modes
•Manual, IR, RS232 and USB control •Plug and play –
DDC1 compliant •Remote power up to 150' •Modular
RJ45 on output and each input •Supports up to 1920
x 1440, 1080p •Includes GUI software and IR remote
•Mfr. #500160
Order #
33-11430
(1–3)
$499.00
(4–up)
$475.00
CATV Balun
The VideoEase
CATV Balun
allows
traditional
75ohm coaxial
cable to be
replaced by a
single pair of Cat 5 UTP cable in the CATV, VHF and
FM environments in certain applications. The CATV
Balun allows broadband CATV equipment to be
integrated into structured cabling systems thereby
allowing CATV equipment to be moved or added to
any convenient modular wall outlet. The CATV balun
works in conjunction with CATV splitters, amplifiers
and cable modems for a total cabling solution.
Mfr. #500302 Features: Low return loss eliminates
“ghosting”. Pair required for use, sold individually.
Order #
33-9630
ONLY
$47.99
Back
CATV Distribution Hub
Designed to be used with the Muxlab 500302 CATV
balun, this hub allows cable TV, off-air, broadband
and other RF video to be distributed to up to eight
television receivers, recorders or similar devices, via
Cat5 cable. It provides gain amplification and port
buffering as well as ground loop isolation. Features:
•900MHz bandwidth •CATV, Internet, digital cable
support •Bi-directional transmission •Single "F"
connector input, eight RJ45 outputs.
Order #
33-11440
33-9630
Mfr. # 500300
500302
Description
1 x 8 hub
CATV balun
ONLY
$629.00
47.99
Dual Audio/
Video Balun
Allows up
to two composite
video signals
and up to two
unbalanced audio
signals to be
transmitted via
unshielded twisted pair (UTP) cable in a point-to-point
connection. Also works in conjunction with MuxLab’s
Audio/Video Distribution Hub (#500200) allowing
audio/video programming to be distributed via UTP
to up to eight locations. Mfr. #500012. Up to 2200'
(670m) Pair required for use, sold individually.
Order #
33-9610
www.MCMelectronics.com /1-800-543-4330
ONLY
$65.99
109
7
VGA Wall Plate Baluns
B
Active VGA Balun II Kit
Complete two piece kit allows VGA video, plus stereo
or digital audio and RS232 to be transmitted via a
single Cat 5e/6 cable. It is DDC compliant and works
in conjunction with separately available IR emitter
and sensors to support IR source control. Resolution
up to 1920 x 1200 is supported at distances up to 600',
and manual brightness, sharpness and skew adjustments
are provided. Full ground loop isolation is also
provided between transmitter and receiver. In addition
to the Cat 5e output, the transmitter also provides local
monitor connection.
Order #
33-11425
33-11480
33-11485
NEW!
NEW!
Back
Section
7
AUDIO/VIDEO
Audio/Video
Distribution
VideoEase™ S-Video
plus Audio Balun
Sends S-video plus full spectrum analog audio over
standard CAT5e/6 cable. Ideal in applications where
full 20Hz~20KHz audio response is critical. Uses
all four Cat5E/6 pairs, and sends signal up to 1000'.
S-Video and L/R RCA female connections to RJ45
female. •Mfr. #500038 •Used in pairs, sold individually
NEW!
7
S-Video and Stereo Audio Balun
with Ground Loop Isolation
NEW!
Dual S-Video Balun
Allows one S-Video signal plus one stereo audio
signal to be transmitted up to 1000' feet via a single
CAT5e/6 cable, and provides a ground loop isolator
to eliminate any hums. •Mfr. #500018 •Must be used
in conjunction with #33-9590
Order #
33-11320
#33-9585
S-Video Baluns
#33-9590
Allows a single S-video signal to be transmitted
via unshielded twisted pair (UTP) cable up to 1000'.
The product is available in two models; the S-Video
Balun (500016) and the S-Video/Audio Balun
(500017). Used in pairs, the S-Video Balun eliminates
costly and bulky S-video cable, allowing S-video
equipment to be connected or moved to any
convenient modular outlet. The S-Video Balun also
works in conjunction with MuxLab’s Audio-Video
Distribution Hub (500200) to allow S-video
programming to be distributed via UTP. Note:
Baluns must be used in pairs and are sold
individually. •Sold individually
Mfr. #
500016
500017
Description
ONLY
S-Video
$27.99
S-Video and Audio 63.99
A
B
Composite Video plus Audio
Balun with IR Pass Through
Order #
33-11490
Fig. Order #
Mfr. #
A
33-11230
500048
B
33-11231
500049
Description
Balun with
6" pigtails
Balun with RCA
connections
Audio/Video Hub
NEW!
The VideoEase Audio-Video Hub allows up to two
baseband composite or one S-video signal and up to
two audio signals to be distributed to up to eight
destinations via twisted pair (UTP) cable for more costeffective and versatile cabling. The Audio-Video Hub
when used in conjunction with MuxLab’s line of
VideoEase baluns, allows coaxial cable to be eliminated
between the audio-video source and the destinations.
The product works with the CCTV Baluns (500000,
500009), Stereo Audio-Video Balun (500001), Dual
Audio-Video Balun (500012) and S-Video Baluns
(500016, 500017). A looping output allows the source
input to be distributed to other baseband audio/video
equipment including matrix switchers, multiplexers,
VCRs and monitors. Applications include: Classroom
audio/video instruction, corporate audio/video
presentations, tradeshow demonstration systems,
CCTV security and surveillance. Features: Up to 2200'
in color via Cat 5 twisted pair cable. 2-year warranty.
Mfr. #500200
(1–3)
$69.88
(4–up)
$65.59
Order #
33-9615
ONLY
$525.00
Videoease Quad
Video Balun
•Developed for the security
video and audio-video
markets, the quad video
balun allows up to four
composite video channels to
be transmitted over one Cat 5 cable, thus replacing up
to four coaxial cables for more cost-efficient cabling
•Supporting composite video up to 2,200' (670m) via
Cat 5 cable and works in pairs •Streamlining cabling in
applications such as security video, video-conferencing,
classroom instruction, tradeshow demos, PC-training,
airline information systems and home entertainment
systems •Mfr. #500032 •Used in pairs, sold individually
Order #
33-10110
ONLY
$65.99
NEW!
BNC Component Video Balun
Allows a 1080i component video signal to be
transmitted up to 500' via CAT5e/6 cable. Features:
•Supports 480i/p transmission up to 1000' •Supports
720p/1080i up to 500' •Includes three BNC jumper
cables •Mfr. #500002 •Used in pairs, sold individually
Order #
33-11300
ONLY
$75.99
Stereo A/V Balun
The VideoEase Stereo Audio/Video Balun allows a single composite video signal and
a maximum of two unbalanced audio signals to be transmitted via unshielded twisted
pair (UTP) cable in a point–to–point connection. The Stereo Audio/Video Balun
eliminates up to three coaxial cables, allowing audio/video equipment to be connected
via space–efficient and cost–effective Cat 5 twisted pair cable. The Stereo Audio/Video
Balun also works in conjunction with MuxLab’s Audio/Video Distribution Hub
(500200) allowing audio/video programming to be distributed via UTP. Features:
Up to 2200' (670m) in color via Cat 5 UTP. Pair required for use, sold individually.
ONLY
$59.99
59.99
(4–up)
$46.09
ONLY
$48.49
Identical to and interchangeable
with the 500038 balun, this balun
fits in a single gang box and is
compatible with decora style wall
plates. Sends S-video plus full
spectrum analog audio over
standard CAT5E/6 cable.
Ideal in applications where full
20Hz~20KHz audio response is
critical. Uses all four Cat5E/6 pairs,
and sends signal up to 1,000'.
S-Video and L/R RCA female
connections to RJ45 female. •Mfr. #500038-WP-US
•Used in pairs, sold individually
Allows one composite video, R/L audio and one
IR signal to be transmitted via CAT5e/CAT6 cable.
Features: •Transmits audio up to 3250' with less than
2dB loss •Transmits video up to 2200' with less than
2dB loss •Screw terminal for IR emitter pass through
•Dimensions: 2½" (L) x 2¼" (W) x 1" (H)
•Used in pairs, sold individually
110
(1–3)
$48.49
ONLY
$62.29
S-Video plus Audio
Wall Plate Balun
Order #
33-9585
33-9590
Order #
33-11345
Allows up to two S-Video signals to be transmitted
up to 1000' via a single CAT5e/6 cable. •Mfr. #500013
•Used in pairs, sold individually
Order #
33-11315
NEW!
Order #
33-9625
www.MCMelectronics.com /1-800-543-4330
Mfr. #
500001
ONLY
$65.99
Follow us on:
&
AUDIO/VIDEO
Audio/Video
Distribution
VideoEase™ Composite
Video/Stereo Balun
The VideoEase™ stereo/video
balun allows a single
composite videosignal and
stereo audio signal to be transmitted via UTP cable up
to 2200' in a point-to-point connection. Features: •Full
audio bandwidth response for high fidelity applications
•20Hz~20KHz audio bandwidth •Built-in color-coded
cable leads for ease of installation •Mfr. #500039
•Used in pairs, sold individually
Order #
33-9626
ONLY
$55.99
Videoease™
Quad Audio Balun
Order #
33-10115
ONLY
$65.99
Decora Mount Balun Fixture
Identical to and interchangeable with
model 500048 and 500049, this balun
fits in a single gang box and is
compatible with decora style wall
plates. Sends composite video plus
full spectrum L/R line level audio
over standard CAT5e/6 cable. Screw
terminals provide access to the
fourth cable pair for pass-thru of IR
signals. Maximum range is 2,200'.
•Mfr. #500049-WP-US •Used in pairs, sold individually
Order #
33-11505
The MonoPro™
XLR connectors
allow a standard
AES analog or
#33-10055
digital audio
channel to be
connected via Cat 5 unshielded twisted pair cable
(UTP) in the professional audio environment. The
product features rugged cable strain relief and comes
with locking XLR3 connectors for added cabling
versatility. Features: •Rugged cable strain relief •Line
analog audio up to 5000' (1.5km) via Cat 5 •Digital
audio up to 1400' (426m) via Cat 5 •Wires terminate
inside product •Locking XLR3 connector •Optional
wire terminal for ground/shield (if required)
•Up to 5000' and 1400' via Cat 5 for analog
or digital audio, respectively.
Mfr. #
500025
500026
Description
MonoPro™ XLR male
MonoPro™ XLR female
The wall mount balun fixture allows
any MuxLab square balun to be
installed behind a decora compatible
wall plate for custom AV installation.
Each balun snaps into place and is held
firmly by a spring latching mechanism.
The one-piece design makes the product
easy to install and maintain. There are
no parts to lose or replace. Mfr. #500910.
Order #
33-10585
ONLY
$34.99
ONLY
$75.99
NEW!
Coaxial Digital Audio Balun
Allows a digital audio signal to be transmitted up
to 600' via a single CAT5e/6 cable. •Mfr. #500020
•Used in pairs, sold individually
Order #
33-11325
VideoEase™
MonoPro™ XLR
Order #
33-10050
33-10055
NEW!
7
7
The quad audio balun
allows up to four analog line
audio signals to be transmitted
via unshielded twisted pair cable
in a point-to-point connection. One pair of quad audio
baluns can replace four coax audio cables with one Cat
5 cable. Features: •Unbalanced, line-level analog audio
up to 5000' via Cat 5 cable •Less than 1dB per pair over
frequency range. Mfr. #500033. Used in pairs,
sold individually.
Stereo A/V Wall
Plate Balun
Section
ONLY
$24.29
NEW!
Surface Mount Balun Plate
Allows Muxlab square baluns to be installed on a wall
or furniture surface for a more permanent and secure
installation. It covers the balun while allowing the pin
configuration to be displayed for ease of reference.
Mounting ears are positioned to allow multiple fixtures
to be installed next to each other. Includes mounting
screws and plastic drywall anchors. Mfr. #500915.
Order #
33-11475
ONLY
$19.99
#33-11470
NEW!
Dual A/V Balun
Allows up to two composite video signals and up to two
unbalanced audio signals to be transmitted up to 2200'
via one CAT5e/6 cable. •Mfr. #500012 •Used in pairs,
sold individually
Order #
33-11310
ONLY
$56.99
ONLY
$27.99
27.99
NEW!
#33-9620
Rack Mount Chassis
Designed as a head-end cable management solution,
this allows any combination of MuxLab square baluns
to be installed within any 19" rack. 16 balun chassis
occupies 2RU space, six balun chassis occupies 1RU.
Blank filler panels available separately.
Order #
33-9620
33-11470
33-11465
Mfr. # 500900
500902
500901
Description
(1–3) (4–up)
16RU panel $229.00 $219.00
6RU panel
169.00 159.00
Blank filler
16.99
16.19
NEW!
NEW!
Stereo Audio Balun
NEW!
43.5mm plug
Allows line level stereo audio to be transmitted up
to 5000' via one CAT5e/6 cable. Features: •Up to 1000',
60Hz~20KHz •1000'~5000', 100Hz~20KHz •Less than
1dB loss •6" RCA leads •Dimensions: 1 7⁄8" (L) x 1"
(dia.) •Mfr. #500027 •Used in pairs, sold individually
Allows unbalanced line level stereo to be transmitted
via CAT5e/6 cable up to 5000'. Features: •Ideal for
connection to sound cards, laptops, MP3 players, etc.
•Transmits up to 1000' at 60Hz~20KHz •Transmits
from 1000'~5000' at 100Hz~20KHz •Less than 1dB loss
•6" 3.5mm cable lead •Dimensions: 47⁄8" (L) x 1" (dia.)
•Mfr. #500030 •Used in pairs, sold individually
Allows unbalanced line level stereo to be transmitted
up to 3250' via a single CAT5e/CAT6 cable.
•Mfr. #33-11330 •Used in pairs, sold individually
Order #
33-11240
Order #
33-11245
Order #
33-11330
Stereo Audio Balun
ONLY
$41.29
ONLY
$41.29
Stereo Audio Balun
www.MCMelectronics.com /1-800-543-4330
ONLY
$44.99
111
Section
7
AUDIO/VIDEO
Audio/Video
Distribution
NEW!
VideoEase™ Passive Video Balun Receiver Hub
VideoEase™ Passive Video Balun Receiver Hub
This 16 port hub allows video, remote power and PTZ
control to be transmitted via one Cat 5 cable. It features
full DC isolation for systems where ground loops may
be present and works in conjunction with all MuxLab
CCTV baluns. Passive device, requires no power.
Order #
33-11415
82-9485
82-9490
33-10065
33-11390
33-11395
Mfr. #
500133
500000
500009
500022
500100
500101
NEW!
Type
(1–3) (4–up)
16CH hub
$625.00 $594.00
Modular balun 27.99
26.59
Compact balun 23.99
22.79
PTZ balun
31.99
30.39
Active balun
82.99
78.79
Active balun
82.99
78.79
Compatible with any MuxLab CCTV video balun, this
hub acts as a 16 channel passive receiver. Perfect for use
with DVR's up to 16 channels, this unit allows cameras
to be located up to 2200' away, sending video over
Cat5A cable. Each of the 16 inputs are screw terminal
for direct connection to unterminated cable pairs.
Outputs are BNC female. Compatible with all baluns
listed below, each available separately. Passive device,
requires no power.
Order #
33-11405
82-9485
82-9490
33-10065
33-9760
Mfr.#
500130
500000
500009
500022
500023
Type
(1–3)
(4–up)
16CH hub $350.00 $330.00
Modular balun 27.99
26.59
Compact balun 23.99
22.79
PTZ balun
31.99
30.39
Mini balun
29.59
28.11
HDMI 1.3 Balun Set
NEW!
4IR and RS232 support
Capable of transmitting video signals at resolutions up
to 1080p up to 328', this balun set also accepts input
from an infrared receiver and transmits the signal via
the same CAT5e/6 cable. Features: •Can also transmit
RS-232 (DB9 connections) up to 115.2kbps •3D ready
•Bi-directional RS232 and IR signals •Maximum data
rate: 3.4Gbps •Audio transmission supports Dolby
TrueHD, DTS-HD MA •Mfr. #HM1CK-3
Order #
33-11200
ONLY
$504.00
7
NEW!
NEW!
NEW!
HDMI Active Balun Set
Passive CCTV Power Integrator Hub
This hub allows video, remote power and PTZ control
to be transmitted via one Cat5e/6 cable between the
CCTV camera and the DVR/IP encoder in the security
video environment. Features: •Built-in 16-channel
CCTV power supply •24/28VAC selector for each port
•Power-thru or pass-thru mode port configuration
•Auto resettable fuses on each port •2RH height
•Seamless integration with 500130, 500022, 500024
•Mfr. #500136
Order #
33-11520
Composite Video Balun
Intended for composite video signal transmission,
this balun is perfect for video surveillance applications.
Uses one Cat5e/6 pair, and sends video up to 2,200'.
RCA male video connection to RJ45 female.
•Mfr. #500031 •Used in pairs, sold individually
Order #
33-11340
ONLY
$899.00
NEW!
(1–3)
$24.19
NEW!
(1–3)
$51.99
(4–up)
$49.39
ONLY
$44.99
NEW!
Back
Passive Component Video
Balun Transformer with Digital Audio
•High-definition balun transformer •Distributes
component video signals with PCM digital audio over
Cat 5 UTP •300'~1000' •Custom designed with wide
bandwidth •Can be used for four composite video
signals •Rugged metal chassis •Mfr. #C5-HDP
CCTV Power plus Video Balun
Allows BNC video as well as power to be
transmitted up to 500' via one CAT5e/6.
•Mfr. 500029 •Used in pairs, sold individually
Order #
33-11335
112
ONLY
$22.19
ONLY
$48.49
NEW!
NEW!
VideoEase™ Active Composite
Video Balun Transmitter
NEW!
ONLY
$201.00
Order #
33-11052
Allows CCTV video and digital pan, tilt and zoom
control signals to be transmitted up to 1400' via
a single CAT5e/6 cable. •Mfr. #500007 •Used in
pairs, sold individually
Order #
33-11305
Order #
33-11050
PTZ Pass-Thru Balun
This unit allows video,
remote power and 2-wire
PTZ control to be
transmitted via one Cat 5e/6
cable, while providing full
ground loop isolation. It may be installed either at the
camera or DVR side in conjunction with other standard
MuxLab CCTV baluns. Maximum distance using
Cat 5e cable is 2200'. Passive device, requires no power.
Mfr. #500132.
Order #
33-11410
PTZ CCTV Balun
(4–up)
$22.99
Complete set allows HDMI signals to be sent
up to 50 meters, over two CAT5e cable runs. Features:
•Transmits 1080i resolution up to 50m, and 1080p
resolution up to 30m •Dip switch digital level and EQ
adjustments •Rugged metal housing •Weight: 1.4lbs.
•Mfr. #HM6EK
Active balun circuitry provides improved performance,
greater range and full ground loop isolation between
video components. They are perfect for video
surveillance applications where distances up to 3000'.
Transmitters are available with 12VDC or 24VAC
power requirements, making them compatible with
most video camera power supplies. Both transmitters
require Mfr. #500009 balun as the receiver.
Order #
33-11390
33-11395
82-9490
Mfr.#
500100
500101
500009
Type
(1–3)
12VDC
$82.99
24VAC
82.99
Passive receiver 23.99
www.MCMelectronics.com /1-800-543-4330
(4–up)
$78.79
78.79
22.79
HD A/V Transmitter Over Cat 5 or 6
•Distributes high definition component or composite
video and digital audio or left and right audio over
extended distances using Cat 5 wire •Active
amplification ensures high-quality transmission •Loop
output for use of additional Cat 5 transmitters •Six Cat
5 outputs for additional locations •Discrete passive IR
channel for the use of external IR remote control
systems •For use with Cat5RX receivers (#33-10256)
•Mfr. #C5T6
Order #
33-11060
ONLY
$201.00
Follow us on:
&
Active HDMI
Over Dual
Category 5
Balun Set
Order #
50-10245
MSRP
$199.00
ONLY
$122.00
#33-10255
HDTV Audio/Video
Distribution Hub and Receiver
4Accommodates component video
(Y/Pb/Pr) plus digital audio
4Active video amplifier circuit
4Loop through output send for multiple receivers
4IR remote path
Distribute high-definition component video and digital
or left or right audio over extended distances using Cat
5e wire. Video and audio loop output to accommodate
future expansion to additional Cat 5e transmitters and
receivers. Supports 1080i video up to 300' with Cat 6.
Mfr. #
Cat5TX
Cat5RX
Description
Transmitter
Receiver
ONLY
$101.00
117.00
Video Balun
Use to send composite
video signal over Cat 5
cable. This balun features
a gold plated female RCA
connector, and female
RJ-45 jack. Screw
terminals are available for
connecting unterminated
Cat 5 cable. Utilizes one
Back
pair (pin 7/8) of Cat 5
cable. Specifications: •Maximum distance: 1000'
•Bandwidth: 50Hz~8MHz •Dimensions (excluding
connector): 1.0" (H) x 0.85" (W) x 2.0" (L)
•Sold individually, must be used in pairs
MSRP
$34.95
(1–3)
$12.99
(4–up)
$11.21
Keystone
Mount
Composite
Video Balun
Intended to
send composite video signal over Cat 5 cable, this balun
features an RCA female connector with yellow insert,
for easy identification as the video path. Rear mounted
IDC connector allows simple, fast connection to
unterminated Cat 5 cable. Maximum distance: 1000'.
Sold individually.
Order #
50-7715
ExtenHD™ transmitters and receivers work together to
allow HDMI digital signal path transmission over Cat
5 or Cat 6 UTP cable (two cables required) up to 250
meters. Used in pairs (sold separately), the transmitter
and receiver allow you to switch between two HDMI
source inputs. Features: •Compliant with HDMI 1.2,
HDCP 1.1 and DVI 1.0 specifications •Supports
resolutions up to 1080p at 50/60Hz. Specifications:
•Input: One HDMI female port •Output: One Cat 5
(RJ-45) jack for video and one Cat 5 (RJ-45) jack for
DDC •Power: 5VDC power supply adapter (included)
Dimensions: 123" (W) x 125" (D) x 30" (H).
MSRP
$34.95
(1-3)
$12.99
(4-up)
$11.21
Order #
33-10450
33-10451
Mfr. #
X-CAT TRAN
X-CAT 50
Description
Transmitter
Receiver (50m)
ONLY
$83.49
83.49
Intended to send composite video signal over Cat 5
cable, this balun features a BNC female connector and
is ideal for use in video surveillance applications. Rear
mounted IDC connector allows simple, fast connection
to unterminated Cat 5 cable. Maximum distance: 1000'.
•Sold individually
Order #
50-7716
BNC Video + DC
Power Balun
MSRP
$34.95
(1-3)
$11.49
Front
4Accommodates
composite video
4Provides path
for 12VDC power
41,000' max distance
Use to send composite
video signal and low
Back
voltage DC over Cat 5
cable. Compact size
and male In addition
to the BNC connection, two screw terminals are
provided for direct access to a second cable pair. This is
ideal for remotely providing DC power to devices such
as surveillance cameras and small LCD television
monitors. Specifications: •Maximum distance: 1000'
•Maximum recommended distance for power: 300'
(using 12VDC, 500mA) •Dimensions (excluding
connector): 1.0" (H) x 0.85" (W) x 2.0" (L)
Order #
50-7745
Keystone
Mount
Composite
Video Balun
HDMI over Category 5 UTP
7
Take advantage of Cat 5 (or higher) cable for interconnecting A/V components over long distances. Common
signal formats such as composite video, RGB component video, S–video and line level audio can easily be sent over
UTP cable distances from 400'~1000' depending on model. In retrofit applications, utilize existing unused pairs of
Cat 5 data cable already in place. In new construction, take advantage of the smaller size and lower cost of Cat 5
cable when distributing signals throughout the structure. Housed in compact ABS enclosures, each balun accepts
standard RJ-45 male connectors. Completely passive design, these units require no power. Each unit is clearly
labeled to identify which RJ-45 connector pair is used for the designated signal path.
Order #
50-7710
#33-10256
Order #
33-10255
33-10256
Audio/Video to Category 5
Balun System
Section
MSRP
$35.95
(1–3)
$20.99
(4–up)
$18.49
BNC Video + DC Power Balun
4Accommodates composite video
4Provides path for
12VDC power
4Convenient 8"
BNC pigtail
41,000' max distance
Use to send composite video signal and low voltage
DC over Cat 5 cable. This compact balun features a
male In addition to the BNC connection, two screw
terminals are provided for direct access to two cable
pairs (in parallel). This is ideal for remotely providing
DC power to devices such as surveillance cameras and
small LCD television monitors. Utilizes three cable
pairs: Specifications: •Distance: 1000' (Cat 5),
•Maximum recommended distance for power:
300' (using 12VDC, 500mA) •Dimensions
(excluding connector): 1.0" (H) x 0.85" (W) x 2.0" (L)
Sold individually, must be used in pairs
Order #
50-7746
MSRP
$39.95
(1-3)
$22.99
(4-up)
$20.39
(4-up)
$10.19
RCA Composite
Video Balun
4Accommodates composite video
4Male RCA connector
4Accepts unterminated Cat 5 cable
41,000' max distance
Front
Back
Use to send composite video signal over Cat 5 cable, this balun features very compact size, and a male RCA
connector for easy attachment directly to equipment including monitors, VCRs, DVD players, processors and
cameras. A specially designed tool-less IDC connector provides quick, reliable connection to unterminated Cat 5
cable. Specifications: •Bandwidth: 50Hz~8MHz •Distance: 1000' max, using 24AWG UTP •Dimensions
(excluding connector): 0.813" (H) x 0.813" (W) x 1.875" (L) •Sold individually, must be used in pairs
Order #
50-7748
MSRP
$25.95
(1-3)
$12.99
www.MCMelectronics.com /1-800-543-4330
(4-up)
$11.21
113
7
Complete kit
consists of an active transmitter and receiver set for
sending HDMI signals over dual Cat 5e or Cat 6 cable
runs. The transmitter unit connects to the HDMI
audio/video device with a HDMI connection. The
receiver is located near the HDTV display source
and connected to the display source with a HDMI
connection. Then, the transmitter and the receiver
units are connected together with two Cat 5 cables that
transmit a pristine high-definition signal between the
A/V device and the HDTV display up to 200' (720p).
Power is required at the receiver end, UL listed AC
adapter is included. Features: •Supports computer
resolutions up to 1920 x 1200 (WUXGA), 12 bit color
depth •HDMI version 1.3 compliant •H.D.C.P. (High
Bandwidth Digital Content Protection) compliant
Distances: •720p: 200' •1080i: 165' •1080p: 100'
Specifications: •Video amplifier bandwidth: 2.25Gbps
•Single link range: 1080p •Input video signal: 0.5~1.0V
p-p •Input DDC signal: 5V p-p (TTL) •Data speed
transfer: 10.2Gbps •Power requirements: 5VDC
•Dimensions (each unit): 2" (W) x 1.88" (H) x 3.25" (D)
AUDIO/VIDEO
Audio/Video
Distribution
Section
7
AUDIO/VIDEO
Audio/Video
Distribution
BNC Video Balun
4Accommodates
composite video
4Convenient
8" BNC pigtail
4Accepts unterminated Cat 5 cable
41,000' max distance
7
Use to send composite video signal over Cat 5 cable,
this compact balun features a male BNC connector
attached to the end of an 8" pigtail. Due to their low
cost, and slim design, multiple units may be connected
side-by-side to equipment. A specially designed tool-less
IDC connector provides quick, reliable connection to
unterminated Cat 5 cable. Specifications: •Bandwidth:
50Hz~8MHz •Distance: 1000' max, using 24AWG UTP
•Dimensions (excluding connector): 0.625" (H)
x 0.625" (W) x 1.563" (L) Sold individually,
must be used in pairs
Order #
50-7751
MSRP
$29.95
(1-3)
$17.49
L/R Audio/Video Balun
Front
4Accommodates composite video
and L/R line level audio
4Female red/white/yellow
RCA connections
41,000' max distance
Use to send composite video,
plus two channels of unbalanced
line level audio over Cat 5 cable.
Back
This balun features three gold
plated female RCA connectors, color coded red, white
and yellow, and a single female RJ-45 jack. Utilizes
three Cat 5 cable pairs: •Red: Pin 1/2 •White: Pin 3/6
•Yellow: Pin 7/8. Specifications: •Video bandwidth:
50Hz~8MHz •Audio bandwidth: 10Hz~50KHz
•Dimensions (excluding connectors): 1.0" (H) x
2.36" (W) x 3.22" (L) Sold individually,
must be used in pairs
Order #
50-7730
MSRP
$79.95
(1–3)
$34.49
(4–up)
$30.58
L/R Audio/Video Balun
4Accommodates composite
video and L/R line level audio
4Convenient pigtail leads
41,000' max distance
Use to send composite video, plus two channels of
unbalanced line level audio over Cat 5 cable. This balun
features three 8" pigtails with gold plated male RCA
connectors, color coded red, white and yellow, and a
single female RJ-45 jack. Specifications: •Video
bandwidth: 50Hz~8MHz •Audio bandwidth:
10Hz~50KHz •Distance: 1000' max (Cat 5)
•Dimensions (excluding connectors): 1.0" (H) x
2.36" (W) x 3.22" (L) Sold individually,
must be used in pairs
Order #
50-7732
(4-up)
$15.29
MSRP
$79.95
(1-3)
$36.49
(4-up)
$32.63
L/R Audio Balun
BNC Video Balun
Front
4Accommodates
composite video
4Male BNC connector
4Accepts unterminated
Cat 5 cable
41,000' max distance
Use to send composite
video signal over Cat 5
cable, this balun’s very
compact size and male BNC connector makes for easy
attachment directly to equipment including monitors,
processors and cameras. Due to their low cost, and slim
design, multiple units may be connected side–by–side to
equipment. A specially designed tool–less IDC
connector provides quick, reliable connection to
unterminated Cat 5 cable. Specifications: •Bandwidth:
50Hz~8MHz •Dimensions (excluding connector):
0.625" (H) x 0.625" (W) x 1.563" (L)
Back
Order #
50-7750
MSRP
$25.95
(1–3)
$16.99
#50-7769
Use to send two channels of
unbalanced line level audio over
Cat 5 cable. This balun features two
gold plated female RCA connectors,
color coded red and white,
Back
and a single female RJ-45 jack.
Utilizes two Cat 5 cable pairs: •Red: Pin 1/2 •White:
Pin 3/6. Specifications: •Maximum distance: 1000'
•Bandwidth: 10Hz~50KHz •Dimensions (excluding
connectors): 0.85" (H) x 1.69" (W) x 1.94" (L)
Order #
50-7725
Back
Order #
50-7742
Front
4Accommodates four composite video signals
4RCA or BNC connectors
41,000' max distance
Use to send up to four independent composite video
signals over a single Cat 5 run. Baluns are available with
either female RCA or BNC connectors, allowing
compatibility with a wide variety of multimedia and
security applications. They are also compatible with
RGB and component video signal formats. Baluns
feature female BNC or RCA connectors, and a single
female RJ-45 jack. Utilizes four Cat 5 cable pairs,
baluns may be inter mixed. Specifications: •Video
bandwidth: 50Hz~8MHz •Distance: 1000' max
(Cat 5) •Dimensions (excluding connectors):
1.0" (H) x 2.28" (W) x 3.22" (L)
Order #
50-7768
50-7769
114
Connectors MSRP
RCA
$74.95
BNC
74.95
(1-3)
$34.49
34.49
(4-up)
$30.58
30.58
(4–up)
$20.39
4Accommodates line level video
4Male RCA connector
4Accepts unterminated Cat 5 cable
41,000' max distance
Front
Four Channel Video Baluns
(1–3)
$22.99
Line Level Audio Balun
(4–up)
$15.54
#50-7768
MSRP
$59.95
Use to send a single channel of
line level audio over Cat 5 cable,
A specially designed tool-less IDC
connector provides quick, reliable
connection to unterminated Cat 5
cable. Specifications: •Bandwidth:
50Hz~8MHz •Dimensions
(excluding connector): 0.813" (H)
x 0.813" (W) x 1.875" (L)
MSRP
$25.95
(1-3)
$17.49
4Accommodates L/R line level audio
4Convenient pigtail leads
41,000' max distance
Use to send two channels of unbalanced line level audio
over Cat 5 cable. This balun features two 8" pigtail
leads, each terminated with gold plated male RCA
connectors, color coded red and white, and a single
female RJ-45 jack. Utilizes two Cat 5 cable
pairs: •Red: Pin 1/2 •White: Pin 3/6 Specifications:
•Bandwidth: 10Hz~50KHz •Distance: 1000' max
(Cat 5) •Dimensions (excluding cables): 0.85" (H)
x 1.69" (W) x 1.94" (L) •Sold individually,
must be used in pairs
Order #
50-7724
MSRP
$69.95
(1-3)
$25.49
(4-up)
$22.43
(4-up)
$15.29
Component Video Balun
4Accommodates component
video (Y/Pb/Pr)
4Female red/green/blue
RCA connections
4400' max distance
Component Video Balun
Use to send Y/Pb/Pr component
video signals over Cat 5 cable. This
balun features three gold plated
female RCA connectors, color
coded red, green and blue, and a
single female RJ-45 jack. Utilizes
three Cat 5 cable pairs: •Red: Pin
7/8 •Green: Pin 3/6 •Blue: Pin 1/2. Specifications:
•Bandwidth: 50Hz~8MHz •Dimensions (excluding
connectors): 1.0" (H) x 3.2" (W) x 2.4" (L) •Sold
individually, must be used in pairs
Order #
50-7720
L/R Audio Balun
MSRP
$99.95
(1–3)
$45.99
www.MCMelectronics.com /1-800-543-4330
(4–up)
$39.99
4Accommodates component video (Y/Pb/Pr)
4Provides path for SPDIF audio
4Convenient pigtail leads
4400' max distance
Use to send Y/Pb/Pr component video signals over
Cat 5 cable. a female orange RCA connector provides
path for digital audio (SPDIF). Cat 5 connection is a
single female RJ-45 jack. Utilizes four pairs: •Red: Pin
7/8 •Green: Pin 3/6 •Blue: Pin 1/2 •SPDF: Pin 4/5
Specifications: •Distance: 400' max (Cat 5) •Dimensions:
1.0" (H) x 3.2" (W) x 2.4" (L) •Sold individually,
must be used in pairs
Order #
50-7722
MSRP
$109.00
Follow us on:
(1-3)
$50.99
&
(4-up)
$45.32
AUDIO/VIDEO
Audio/Video
Distribution
#50-10255
#50-10265
#50-10270
Section
7
#50-10250
VGA Balun Series
Component Audio/Video HDTV
Distribution Amplifier with Digital Audio
4Interchangeable wall plate and stand alone models
4Accommodates VGA signals
4Range up to 450' depending upon resolution
VGA
Order # Type
Side ConnectorMSRP (1-3) (4-up)
50-10250In-line
PC
Male $99.95$50.99$43.01
50-10255In-line
Monitor Female 99.95 50.99 43.01
50-10265Wall plate PC
Female 99.95 50.99 43.01
50-10270Wall plate Monitor Female 99.95 50.99 43.01
4Single input with eight outputs
4Loop through output to cascade additional units
4Compatible with Y/Pr/Pb and composite video applications
4Accommodates L/R line level and SPDIF digital audio
Distribute digital and analog television signals, from
a single A/V source to nine televisions/receivers, or
use one port as a loop-thru output port to cascade
additional distribution amplifiers. Features:
•Component video (Y, Pr, Pb, or Y, Cr, Cb),
composite video, analog audio and SPDIF digital
audio distribution •High bandwidth (>50MHz)
performance, low distortion, and one-to-one signal
ratio ensures equal picture quality. Power: 9~10VAC,
500mA adapter included. Mfr. #AV901HD.
Order #
33-10090
ONLY
$202.00
Component Audio/Video
HDTV Distribution Amplifier
4Single input with eight outputs
4Loop through output to cascade additional units
4Accommodates component video (Y/Pr/Pb) applications
4Accommodates L/R line level audio
Distribute digital/HDTV and analog television signals
from a single A/V source to nine televisions/receivers,
or use one of the output ports to cascade additional
distribution amplifiers. Features: •Component video
(Y, Pr, Pb) and audio distribution •Compatible with all
HDTV, digital and analog signals •High performance,
low distortion, one-to-one signal ratio ensures equal
picture quality •Unlimited cascade capability
•Mfr. #AV901COMP
Order #
33-10080
ONLY
$117.00
S–Video Balun
4Accommodates S-video
4Seperate chroma and
luminance paths
4Accepts unterminated Cat 5 cable
41,000' max distance
Back
Use to send S–video signal over
Cat 5 cable. Independent balun
circuits provide separate paths
for chroma and luminance
signals, utilizing two pairs of
Front
Cat 5 cable. This balun features
a female 4 pin S–video connector,
and female RJ-45 jack. Utilizes pin 7/8 (luminance)
and pin 4/5 (chroma). Specifications: •Bandwidth:
DC~6MHz •Dimensions: 1.19" (dia.) x 2" (L)
Sold individually, must be used in pairs
Order #
50-7735
MSRP
$39.95
(1–3)
$18.49
(4–up)
$16.31
Component Video
Distribution Amplifier
Component Audio/Video HDTV Distribution
Amplifier with Digital Audio
4Single input with four outputs
4Accommodates component video
(Y/Pr/Pb) applications
4Accommodates L/R line level audio
Four-way audio/component-video distribution
amplifier for Y, Cb, Cr and Y, Pr, Pb applications.
Features high performance, low distortion and true
one-to-one signal ratio. These professional grade
amplifiers are cascadable for use in large displays and
are enclosed in metal housings to reduce interference.
Mfr. #AV400COMP.
Order #
33-7050
ONLY
$95.99
4Single input with four outputs
4Loop through output to cascade additional units
4Compatible with Y/Pr/Pb and composite video applications
4Accommodates L/R line level and SPDIF digital audio
Allows for multiple signal distribution equal to source
signal input. Distribute digital/HDTV and analog
television signals, including digital audio and
composite video from a single A/V source to five
televisions/receivers, or use one loop-thru output
port to cascade additional distribution amplifiers.
Features: •Component video (Y, Pr, Pb, or Y, Cr, Cb),
composite video and SPDIF digital audio distribution
•Compatible with all HDTV, digital and analog
signals •High bandwidth (>50MHz) performance, low
distortion, and one-to-one signal ratio ensures equal
picture quality Power: •9~10VAC, 500mA adapter
included •Mfr. #AV501HDX
Order #
33-10087
S-Video Distribution Amplifier
Keystone Audio Baluns
Intended to send line level audio signals over Cat 5
cable, these baluns are sold as individual red and white
units. Internally identical units feature RCA female
connectors with the appropriate color code insert, for
easy identification of left or right audio channel. Rear
mounted IDC connector allows simple, fast connection
to unterminated Cat 5 cable. Maximum distance: 1000'.
Sold individually.
Allows for multiple signal distribution equal to the
source signal input. Four way audio/video distribution
amplifier with S-video inputs and outputs. Features
high performance, low distortion and true one-to-one
signal ratio. These professional grade amplifiers are
cascadable for use in large displays and are enclosed
in metal housings to reduce interference.
Mfr. #AV400SV.
Order #
50-7760
50-7761
Order #
33-7045
Color
Red
White
MSRP
$36.95
36.95
(1-3)
$13.99
13.99
(4-up)
$12.23
12.23
ONLY
$70.99
ONLY
$151.00
High-Performance
Distribution Amps
4Single input with four or seven outputs
4Accommodates L/R line level audio and composite video
These high-performance distribution amplifiers feature
specifications such as a true one-to-one ratio, no signal
loss, low noise, low distortion and unity gain.
Order #
33-6875
33-6880
Mfr. #
AV400
AV700
www.MCMelectronics.com /1-800-543-4330
Outputs
Four
Seven
ONLY
$50.49
65.99
115
7
Ideal when computer monitor or other high-resolution
video signal needs to be sent long distances. Cable runs
are greatly eased by the use of smaller, lower cost Cat 5
UTP cable. These are perfect for installation of
multimedia systems in educational environments,
boardrooms and public areas. All units consist of an
HD-15 connector for connection to the PC or monitor,
and a female RJ-45 for connection to the UTP cable.
Four different configurations are available, allowing a
wide variety of installation possibilities. Distance (Cat
5): •VGA (640 x 480): 450' •SVGA (800 x 600): 350'
•XGA (1024 x 768): 250' •SXGA (1280 x 1024): 200'
Note: Baluns are sold individually and must be used in
pairs. A pair must include one PC side balun and one
monitor side balun.
Section
7
AUDIO/VIDEO
Audio/Video
Distribution
HDMI Distribution
Amplifier
7
•Enhanced amplified
signals for longer cable
runs •HDMI/HDCP
compliant •Supports
high-resolution
displays of UXGA,
480i, 480p, 720p, 1080i,
1080p •Secure HDMI
connection with
integrated cable
retention bracket •Multiple amplifiers can be cascaded
for additional high definition distribution
Mfr. #
HA4-3
HA8
Description
1 x 4
1 x 8
Digital Media
Player
NEW!
Back
HDMI To Composite Scaler
NEW!
Order #
33-11055
33-11057
NEW!
•HDMI 1.2a compliant •HDCP content protection
compliant (pass signal with HDCP downgrade)
•Converts signal from HDMI formats 480i, 480p,
576p, 720p, 1080i, 1080p (digital signals), to NTSC
480i (analog signal) •Easy installation •Audio output
impedence: 1Kohm •Power requirement: 5VDC, 1A
with 2.1mm power jack •Power supply included
•Mfr. #HSC11
Order #
33-11065
ONLY
$101.00
•Excellent costeffective digital
signage solution
in stand-alone
applications •Easily installs on the back of most LCD
panels •Easy-to-use interface •Includes remote control
•Playback formats: (video) MPEG-1, MPEG-2,
MPEG-4, (audio) WAV, MP3 •Supported media cards:
Compact flash type I/II, IBM micro drive, MMC, MS,
MS-Pro, MS-Duo, SD •Package includes: Digital media
player, stereo audio cable, infared remote control, user
manual, composite video cable, S-video cable, and
power adapter •Mfr. #MP50A
Order #
33-11075
ONLY
$181.00
NEW!
ONLY
$242.00
393.00
Back
NEW!
Five
Channel DC
Isolation
Unit
•This isolation transformer connects into the audio/
video system and breaks the ground path through
cables between components •Eliminates the dreaded
hum bars •Compatible with HD component
distribution amplifiers •Up to three video channels may
be used for three individual composite video signals if
desired •Mfr. #DCB101
Order #
33-11062
Compact High-Definition NEW!
Digital Media Player
•Plays media (MPEG1, MPEG2, MPEG4, DivxHD,
WMV and WVM9-HD) from included 2Gb compact
flash, thumb drive (not included), or from your network
via Ethernet •Ideal for video signage, high-definition TV
wall displays •Durable construction for 24/7 playback
•Outputs: Component video, VGA, composite video,
digital audio, L/R audio •Mfr. #HD300ZX
Order #
33-11070
ONLY
$353.00
NEW!
4Coaxial digital output
Simple solution for feeding multiple HDMI sources to
two different displays. Digital coaxial output allows for
connection to home theater amplifier. Audio signal can
also be transmitted via HDMI. Features: •HDMI 1.3,
HDCP 2.0 compliant •Digital coaxial audio output
(output A only) •Supports up to 1080p resolution
•Remote control included •Dimensions: 83⁄4" (W)
x 1" (H) x 2¾" (D)
Order #
33-11100
MSRP
$179.99
ONLY
$101.00
Mfr. #
MP400A ONLY
$807.00
#33-10533
HDMI Distribution Amplifiers
HDMI 4 x 2 Matrix Switch
Order #
33-11080
#33-10535
ONLY
$40.49
TM
HD Digital Media Player
•Use any HD display for digital signage applications
•High-definition real time decoding up to 25Mbps over
ethernet •Multi-layering video and web browser
•Integrated event logging •UDP/RTP multicast stream
MPEG2 and H.264 decoding •Integrated play list
•Media files •Programmable durations •Loop and
schedule functions •Multiple play list support
•Includes 4Gb flash card
Split one HDMI source to distribute to multiple
high-definition displays. Ideal for retail displays,
entertainment venues, and multiple residential displays.
Extends the range of HDMI compliant device by
equalizing and boosting the HDMI signal up to an
additional 50'. Specifications: •Input/output: HDMI
v1.2a+, HDCP 1.0/1.1 •Video formats supported: VGA
1920 x 1200 and 1080p •Operating frequency: Up to
165MHz •External power supply (included): 5VDC
for 110V
Dimensions (L x W x H) with feet
Order # Description MSRP (1-4) (5-9) (10-24)(25-up)
3.4" x 1.73" x .66"
33-10540 1 x 2 $179.00$55.99$47.63 –
–
10.625" x 7.18" x 1.83"
33-10542 1 x 4
249.00121.00118.00 $ 112.00 $107.00
17.323" x 7.893" x 1.748"
33-10545 1 x 8
399.00252.00248.00 242.00 231.00
NEW!
TM
Three Way HDMI Switch
#33-10532
HDMI 1.3 Input Switch
•Easily switch between multiple HDMI sources while
running a single HDMI cable to your high-definition
display •Extends the range of HDMI compliant device
by equalizing HDMI signal •Included discrete IR
remote (not included with #33-10532) •Auto sensing
inputs allow switching between only active HDMI
sources Specifications: •Output video: HDMI 1.3b +
HDCP 1.0/1.1 •Video formats supported: Up to VGA
920 x 1200 and HD 1080P •Video amplifier bandwidth:
2.5Gpbs/250MHz •External power supply (included):
2A 5VDC for 110V (neither included nor required
for #33-10532)
Order #
33-10532
33-10533
33-10535
Description
2 x 1
3 x 1
5 x 1
MSRP
$59.95
79.95
109.00
(1-4)
$25.49 32.49 50.49 •Supports 1080p resolution •Automatically switches
between HDMI input sources •Push button operation
•Remote control included for manual operation •Two
rear panel inputs, one front panel input •Rear panel
output •HDMI v1.3 HDCP compliant •5VDC, 1A
power supply (included)
Order #
33-11105
116
MSRP
$69.99
www.MCMelectronics.com /1-800-543-4330
ONLY
$40.49
Follow us on:
&
(5-up)
$20.05
29.67
45.04
Back
AUDIO/VIDEO
Audio/Video
Distribution
NEW!
HDMI Scaling Media Center
•This six-input media center switch allows you to scale
all source inputs to 1080p and send them over a single
HDMI cable to your display •Perfect solution for
utilizing older A/V equipment or PCs with new highdefinition displays •Switch among six sources: Two
HDMI, two analog (composite, S-video, or
component), and two VGA Specifications: •HDMI
v1.3, HDCP (Input pixel clock rate: 25MHz~225MHz)
•Supports video up scaling to 1080p (pixel clock rate:
25MHz~165MHz) •3D Y/C separation comb-filter
•Aspect ratio: 4:3 or 16:9 •10 bits video processor for
analog to digital conversion •IR remote control and
manual control •Dimensions: 133⁄8" x 63⁄4" x 15⁄8"
•5VDC, 4A power supply (included)
Order #
33-10800
MSRP
$429.00
7
Component Video/Audio to HDMI Converter
Compact adapter accepts line level left and right audio,
plus component video (Y/Pr/Pb) video and provides
HDMI output. •L/R RCA audio inputs •Red blue
green RCA female input •HDMI female output
•SPDIF digital audio output •Supports multiple
resolutions, the output resolution matches that of
the input •Dimensions: 1.1" (H) x 2.9" (W) x 1.3" (D)
•Mfr. #PYPBHD40
Order #
50-13835
ONLY
$272.00
(1–3)
$65.49
(4–up)
$62.10
NEW!
Compact adapter accepts line level left and right audio,
plus component video (Y/Pr/Pb) video and provides
VGA plus audio output. •3.5mm audio inputs •Red
Blue Green RCA female input •HD15 female output
•3.5mm audio output •Supports multiple resolutions,
the output resolution matches that of the input
•Dimensions: 1.1" (H) x 2.9" (W) x 1.3" (D)
•Mfr. #PYPBV760
Order #
50-13840
(1–3)
$63.49
High-Definition
Automatic Switcher
Back
•Hook up multiple video game systems, DVDs, VCRs,
and any other A/V device to any TV that lacks the
required number of AV inputs •Four inputs allow you
to automatically switch between desired components
•Features four audio/video, S-video, and component
inputs; composite, S-video and component out
•Component inputs provide ultimate picture
performance and are found on most quality TVs/
HDTVs and DVDs •Easy to hook-up and prevents
cable swapping issues that could result in the jacks on
the TV needing to be replaced.
Order #
PH61150
ONLY
$30.49
Back
(4–up)
$59.98
A/V Digital Analog Selector with IR Remote
Full-featured switcher connects up to three “like-kind”
sources (HDMI to HDMI, VGA to VGA, etc.) to a
single HDTV display. Features: •HDMI, VGA, RGB
component video, and composite A/V connections
•Delivers clean, uncompressed digital signals
•Engineered for optimal signal transfer and minimal
signal loss •Built-in HDMI output signal extender up to
100' (total length) •H.D.C.P. (High-Bandwidth Digital
Content Protection) compliant •Supports highdefinition 1080p and UXGA •Compact, time-saving
LED illuminated control center and easy selection with
remote control or front panel push-button controls
•Power: 6V,400mA AC/DC power adapter (included)
•Dimensions: 121⁄2" x 6" x 21⁄4".
Order #
33-10424
ONLY
$173.00
TM
Composite/S-Video to HDMI Scaler
NEW!
S-Video/Composite to HDMI Up-Converter
Ideal if you need to connect your old video game
system, DVD player, VCR, or any other A/V source to
a new HDMI equipped television. The PCVHDM49
will also up-convert the image to 720p resolution.
Features: •Unit will also transmit audio signals via
HDMI •Powered via included AC adapter
•Dimensions: 6" (L) x 3 1⁄3" (W) x 1" (H)
Order #
50-13730 •Use your composite and S-video equipment with
HDMI televisions, switches, receivers and more •Basic
upscaling to 720P at 60MHz •Syncs audio and video
channels •Works with any HDMI to DVI adapter
•Dimensions: 6.1" x 2.75" x 0.90" •Includes 5V, 2A
power supply
Order #
33-10720
MSRP
$179.00
ONLY
$60.99
ONLY
$87.99
Back
NEW!
Six-Way Video Selector
Compact adapter accepts line level left and right audio,
plus VGA video and provides HDMI output. •3.5mm
audio input •HD15 VGA input •HDMI female output
•Supports multiple VGA resolutions, the output
resolution matches that of the input •Dimensions:
1.1" (H) x 2.9" (W) x 4.3" (D) •Mfr. #PVHDM35
Tabletop video switcher provides independent selection
of up to six A/V sources, routing them to two different
destinations. Dual outputs, with independent selectors,
allow easy recording of one source, while viewing
another, or viewing of two different sources on separate
monitors. Inputs and outputs are standard line level
L/R audio, composite video, and S-video.Rugged metal
enclosure measures 13⁄4" (H) x 111⁄2" (W) x 51⁄4" (D),
including non-skid rubber feet. Note: Either composite
or S-video inputs may be utilized, but not both. This
selector will not convert from one video format to the
other. Passive device requires no power.
Order #
50-13830
Order #
50-7780
Back
Remote Control Audio/Video Selector
This switcher can handle almost any consumer
audio/video device you can throw at it. With the most
common audio and video inputs; S-video, composite
video, toslink digital audio and line level audio, you
can connect your DVD, satellite receiver, VCR or
game system to your home entertainment system.
The switcher has three audio/video inputs and one
audio/video output and an ultra thin remote control.
Order #
33-7755
(ea.)
$52.49
(2-4)
$49.60
(5-up)
$47.14
VGA/Audio to HDMI Converter
(1–3)
$65.49
(4–up)
$62.10
MSRP
$69.95
www.MCMelectronics.com /1-800-543-4330
(1-3)
$46.99
(4-up)
$43.01
117
7
Component Video/Audio to VGA Converter
Back
Section
Section
7
AUDIO/VIDEO
Audio/Video
Distribution
Front
Back
NEW!
Back
RF Modulator and Video Switcher
4Four input selector
4Accepts S-video or composite video/line
level audio sources
4Selectable output on CH3 or CH4
TM
7
TM
RF Modulator
Allows connection of any audio/video source to a
television without RCA inputs. Modulator is also
cascadable (using standard CATV signal combiners),
allowing a single coaxial cable to carry multiple video
sources. Features: •Three RCA inputs (composite video
and stereo audio) •Digital channel display •CATV
channels: 64~125 (except 95~99) •UHF channels: 14~69
•3' coaxial cable included •Channel memory •Operates
on 9VDC, 200mA power supply (included)
Order #
33-11095
MSRP
$49.99
ONLY
$29.99
SLV A/V RF Modulator
4Accepts composite video/line level audio source
4Selectable output on CH3 or CH4
4Auto switching between antenna and A/V source
The mini RF modulator is a compact, inexpensive
modulator that will convert any composite video
source to VHF for viewing on your TV on either
channel 3 or 4. Its low signal loss enables it to deliver
excellent picture and sound quality. This modulator
allows you to connect additional A/V components,
such as a DVD player or a gaming system, to your TV
when there are no available RCA jacks. Inputs: Three
RCA (composite video and stereo audio), one “F”.
Order #
33-9775
MSRP
$19.99
(1-9)
$12.95
•Lets you connect components with S-video or
composite output (DVD, satellite) to a TV without
A/V jacks, by modulating the signal to RF •Ideal for
hooking up several components to a TV •Combines
RF modulator and S-video switcher into one unit
•Converts any input (S-video, composite, A/V, stereo)
to RF output •A/V and S-video switching •Composite
to S-video convertor •Front input, stereo input •Gold
plated connectors
Order #
CRF940
ONLY
$25.95
(10-49)
$12.69
Back
Digital UHF Modulator
4Accepts composite video/line level audio source
4Selectable output on UHF 14~69 and CATV 65~139
4LED output channel display
Audio/Video Selector
•Perfect for the
entertainment center
•Combines four different video devices (VCR, laser disc
player, etc.) into one output •Compatible with both
mono and stereo devices •Four audio/video inputs, one
audio/ video output •20Hz~10MHz frequency range
•Isolation 30dB minimum
Order #
32-4420
ONLY
$15.50
Back
Four Way A/V Distribution Amplifier
•Perfect for in­–store display demonstration walls or
karaoke display •One input distributes four amplified
outputs •Video and stereo sound input via RCA jacks
•Frequency range: •20Hz~10KHz •Isolation: 30dB
minimum •Video input: 75ohm •Audio input: 20Kohm
•Operates from 15V/300mA adapter
•Adapter included
Order #
32-4430
The USM-8D is a low cost, frequency stable, UHF
modulator developed for use in adding satellite, VCR,
or security video channels to an existing home
distribution system. The frequency adjustable feature
allows multiple channel use at an extremely low cost.
Specifications: •Frequency range: UHF channels 14~69
and CATV channels 65~139 •Video input: Composite
•Output impedance: 75ohm •Output level: 7dBmV
•Power input: 115VAC, 60Hz, 5W •Connectors: “F”
for RF, RCA video and audio •Mfr. #USM-8D
Order #
33-2740
Composite Video to
S-Video Adapter
This high-quality adapter
converts composite video to S–video and S–video to
composite video. The adapter measures only 13⁄4" long
and 1⁄2" in diameter allowing it to plug directly into the
equipment and solves the problems associated with
mixing composite and S–video inputs and outputs.
Digital RF
Modulators
4Models available with 1, 2 or 4 inputs
4Places each input source on an independent channel
4Selectable output on UHF 14~69 and CATV 65~125
4Allows source selection by simply changing channels
Order #
5515
5525-01
5545-01
118
Outputs
1
2
4
ONLY
$72.00
124.00
197.00
(10-up)
$41.25
ONLY
$27.95
Back
The 5515, 5525-01 and 5545-01 are one, two and four
channel input modulators with loop–out capabilities
and integrated IR control. Each offers IR emitter
output jacks and the ability to remotely power a
DA-550 series or an DA-8200 series distribution panel
from up to 75' away. The 5500 series works with both
the 12 volt and 5 volt IR systems and accessories. The
5515, 5525-01 and 5545-01 offer 75ohm termination
jumpers on all channels to loop–through the video and
audio signals. Features include: 1, 2 and 4 channels, push
button programming, UHF 14~64 and CATV 65~125,
25dBmV output.
(1-9)
$45.95
Order #
33-0001
33-0002
33-0003
A/V Distribution Amplifier/Selector
Description
S male to RCA female
S female to RCA female
S female to RCA male
(ea.)
$7.89
6.39
6.39
(2-up)
$7.59
6.19
6.19
Tabletop distribution amplifier allows selection
between two A/V inputs and provides up to four
outputs. Independent left and right audio signal paths
allow compatibility with stereo sources Front panel
pushbutton selects between two input sources, and
internal amplifier maintains signal quality when
distributed to four outputs. Gain at each output is
2dB over input signal level. Rugged metal enclosure
measures 15⁄8" (H) x 7" (W) x 27⁄8" (D), including
non–skid rubber feet. Requires 12VDC,
AC adapter included.
Add additional
components to
your TV and
home theater system by providing additional A/V
inputs to your system. Four A/V inputs including
composite video and Y/C (S–video). Mfr. #SVS-14.
Order #
30-1376
Order #
80-3450
MSRP
$49.95
(1-3)
$24.95
www.MCMelectronics.com /1-800-543-4330
(4-up)
$22.50
Audio/Video
Switcher
ONLY
$29.95
Follow us on:
&
AUDIO/VIDEO
Audio/Video
Distribution
NEW!
Prograde 1 GHz
Bi-Directional
RF Amplifier
•Compatible with
HDTV and cable modems •1GHz bandwidth
bidirectional amplifier •High pass filter: 54MHz~1GHz
reduces cross mod •Low pass filter: 5MHz~40MHz in
return path •20dB forward gain with 20dB adjustable
attenuator •Mfr. #6001
Order #
33-11085
ONLY
$49.99
HDTV Adjustable Distribution Amplifier
Order # Mfr. #
33-11045 70-0039
33-11046 70-0019
33-11047 70-0041
Description
HDTV adjustable
distribution amplifier
Custom 19" rack adapter
Custom enclosure adapter
Affinity™ Digital Cable Combiner
Affinity™ Eight
Output Digital
Cable Combiner
Allows signal from
two RF modulators
to be injected
directly onto a
digital cable feed,
and distributed to up to eight televisions, without the
need for additional filters. Kit consists of the signal
combiner which accepts three coaxial inputs, one digital
cable and two modulated sources. Each of eight outputs
feeds that signal to a remote location, and allows each
location to independently switch between the digital
cable feed, or the modulated signal. Eight remote IR
coax targets are included for placement at each remote
television. The system also provides an IR engine,
allowing remote control of source devices, with the
simple addition of standard IR targets at the signal
combiner. Mfr. #P0328.
Order #
50-12950
ONLY
$199.00
(1–2)
$325.00
#33-2840
(3–up)
$309.00
#33-2845
Distribution Panel
Order #
DA-506BID
ONLY
$79.95
Broadband Distribution Amplifiers
Specifications: ZCM-101 RF: •Frequency range:
50~550MHz •Gain: 10dB •Noise figure: 3.5dB
•Impedance-all ports: 75ohm ZCM-201 RF:
•Frequency range: 50~550MHz •Gain: 20dB
•Noise figure: 3.5dB •Impedance all ports: 75ohm
Order #
33-2840
33-2845
Mfr. #
ZCM-101
ZCM-201
(1-9)
$14.95
21.50
NEW!
Allows signal from any standard RF
modulator to be injected directly onto a
digital cable feed, without the need for
additional filters. Kit consists of two
pieces, the signal combiner and remote
IR coax target. Simply place the signal
combiner at the source, and the IR coax
target at the remote television. The
included IR remote allows the user to select between the
modulated source and digital cable. The system also
provides an IR engine, allowing remote control of
source devices, with the simple addition of standard IR
targets at the signal combiner. Mfr. #P0321
Order #
50-12940
(1–2)
$129.00
(3–up)
$123.00
Push-Pull
Amplifiers
The CA-30 is
a high-quality
push-pull
amplifier
producing signals with extremely low distortion and
harmonic content. The CA-30 enclosure uses a black
anodized aluminum extrusion to assure reliable heat
sinking and corrosion resistance. Features: •Wide
frequency range: 54MHz~550MHz, 30dB gain,
adjustable slope control, adjustable gain control, input
and output test points, designed for CATV apartment
distribution systems Specifications: •Bandwidth:
54~550MHz •Gain: 30dB •Gain adjust range: 0~8dB
•Power requirements: 115VAC, 60Hz, 4W •Slope:
0~8dB variable •Noise figure: CA-30, 5.0dB
39.99
19.99
Creates an ideal entry level
product for broadband
distribution. Has one input for
CATV or off–air antenna and six outputs. Four outputs
are for up to 75' and two are for 150'. Has bi–directional
capabilities allowing for compatibility with cable
modem and interactive set–top boxes. Specifications:
Bandwidth 54~806MHz. Gain: 20dB +/- 1dB.
7
Order #
33-2670
(1-9)
$179.00
(10-up)
$174.00
(10-up)
$14.25
20.20
#33-8745
DA-520A
The DA-520A is a
bi–directional amplifier providing 20dB of forward
gain and 0dB reverse gain. Specifications: Bandwidth:
54~806MHz. Gain: 20dB +/- 1dB.
Order #
DA-520A
ONLY
$70.00
Remote Control
A/B Switch
Broadband Distribution Amps
•You’ll never have to leave the comfort of your chair
with this infrared remote control video switch •Allows
you to switch between two 75ohm inputs (cable,
antenna, satellite or dual cable systems) •75ohm output
(TV) •AC adapter: 120VAC/12VDC, 100mA included
•5MHz~900MHz bandwidth •89dB isolation •UL
listed •Remote requires two “AA” batteries not included
Order #
32-4425
32-4426
Description
Switch
Replacement remote
(ea.)
$27.95
7.12
(2-up)
$22.50
-
#33-8760
For broadband applications up to 1GHz including cable
television and digital television. Suitable for medium
sized distribution networks including homes and small
condominium complexes. High gain low noise amplifier
with built–in FM trap. Specifications: Frequency range
40~1000MHz. FM trap -20dB. Power: 120VAC.
Order # Outputs
33-8745
1
33-8755
2
33-8760
4
Gain Gain Adjust (1-9) (10-up)
36dB
18dB
$26.95 $24.95
15dB
10dB
24.95 22.95
11dB
–
23.95 21.95
www.MCMelectronics.com /1-800-543-4330
119
7
•Instant cable provider signal strength indicator
•Eliminates screw-on attenuators •Extends precise
signal strength beyond typical “no-loss” distribution
amplifiers •Specifically designed for HDTV
broadcasting (VSB8 & QAM64) •Meets and/or
exceeds cable modem and PPV requirements •Protects
equipment against voltage insertion •Eight independent
adjustable attenuators (range: 0~40dB) •Nominal gain
per output: 3dB+ •Forward bandwidth: 54~1.2GHz
•Return bandwidth: 5~42MHz at 5dB gain •Maximum
output on all 8 ports: +25dBmV/CH •Typical noise
figure: < 4.5dB •Surge protection on all 8 ports:
6KV/3KA
NEW!
Section
Section
7
AUDIO/VIDEO
Audio/Video
Distribution
RF Splitters
Four-Way
Couplers
•For indoor and outdoor use
•RF shielding exceeds FCC
specifications •Maintains
75ohm impedance on trunk •Full
5MHz~900MHz operational range
•Use 75ohm terminator on last
trunk output (MCM #33-550)
Order #
33-1425
33-1430
33-1435
RF Splitters
Description
16dB
20dB
24dB
7
•75ohm splitters for use with cable, antenna, satellite,
broadband, and other RF distributions •High
frequencies available for use with digital satellite
and broadband systems •All ports power passing
Frequency
Order # Outputs Range
33-10955 2 5~1000MHz
33-10956 3 5~1000MHz
33-10957 4 5~1000MHz
33-10960 2 5~2300MHz
33-10961 3 5~2300MHz
33-10962 4 5~2300MHz
(1-9) (10-24)(25-49)(50-up)
$0.80 $0.76 $0.70 $0.63
0.90 0.86 0.79 0.71
1.00 0.95 0.88 0.79
1.50 1.43 1.31 1.18
2.01 1.91 1.76 1.59
2.51 2.41 2.31 2.25
(1-9)
$6.31
6.31
6.55
(10-49)
$5.98
5.98
6.16
(50-up)
$5.45
5.45
5.63
C
B
Power passive splitters
allow for use of
in-line amplifiers and other DC powered devices.
For applications to 1000MHz.
Fig.
A
B
C
Order #
33-4400
33-4405
33-4410
Mini Hi-Frequency Splitter
Mini hi-frequency splitter saves
space in confined areas. DC passive
one port. Attached plastic cable
channel provides neat installations.
Bandwidth: 5~2250MHz. Measures:
2" x 2" x 1" (port to port).
Order #
33-4860
(1-9)
$5.24
(10-up)
$4.86
Power Passive
Splitters
A
Description
2-way
3-way
4-way
(1-9)
$2.72
3.32
4.03
(10-up)
$2.31
2.82
3.52
CATV FM Tapoff
•Zinc die-cast mounting •Provides
connection to stereo tuner for
MTV and other FM broadcasts
usually available on cable TV lines
Order #
33-350
(1-9)
$2.11
(10-99)
$1.99
(100-up)
$1.91
RF Filters and Attenuators
Ground
Isolation
Transformer
Cable Modem Isolator
Separates and isolates
noise/EMI caused by
higher cable modem
transmission signals.
Improves internet download
reliability and reduces cable
modem “sync” problems. Easily
plugs into coax wall jack allowing dedicated runs to
a cable modem and TV tuner. •Frequency range:
10~770MHz •Insertion loss: <5.0db.
Order #
33-10395
5MHz~2.4GHz
bandwidth for use in antenna, cable television and
satellite systems. Reduces the effects of ground loops
such as herringbone, beat and audio hum.
Order #
33-8700
(1-9)
$20.49
ONLY
$3.12
•Blocks DC and low frequency
AC power •Solid brass body
with nickel plating •Female to
male fittings •22 gauge spring
steel center pin •1~1000MHz
bandwidth •16dB return loss •0.3dB insertion loss
Order #
33-0020
(1-9)
$2.72
(10-up)
$2.41
Low Pass Filters
A low pass filter is used on systems when the
broadband feed is supplied by a CATV service. The
filter removes all CATV channels above the pass band,
allowing insertion of locally generated channels.
Order #
LPF-380
LPF-470
LPF-600
LPF-750
Pass Band (MHz)
40~380MHz
40~470MHz
40~600MHz
40~750MHz
ONLY
$22.49
23.49
35.49
37.49
FM Trap
Audio from the FM band
can overcome the audio on
adjacent television channels
6 and 7 and harmonics of
the FM carrier. The FM trap eliminates the entire
FM band from 88 to 108MHz reducing video noise
and audio interference.
(50-up)
$2.41
Features: Nickel-plated,
solid brass body, monolithic
ceramic printed circuit board, ensuring rugged
construction, etched glaze-type resistors provide ±5%
accuracy and excellent return loss, small 1.375" size,
22-gauge spring steel center pin, female to male fitting,
not DC passive. Specifications: •Bandwidth:
100KHz~1750MHz •Return loss: 20dB typical
•Accuracy: ±5%
Order #
33-2750
33-2755
33-2760
33-2765
33-2770
33-2775
33-2780
Description
3dB
6dB
8dB
10dB
12dB
16dB
20dB
(1-9)
$1.40
1.40
1.40
1.40
1.81
1.40
1.40
(10-up)
$1.30
1.07
1.07
1.30
1.39
1.07
1.07
Fixed Mini-Types
•Nickel plated solid brass
body •Monolithic ceramic
printed circuit board, ensuring
rugged construction •Bandwidth:
5KHz~950MHz •Not DC passive •5%
accuracy •22 gauge steel center pin •Small: 13⁄8" size
•“F” type female to male •75ohm •Three attenuators
to choose from •Sorry–no mixing of values for
quantity pricing.
Order #
33-790
33-795
33-810
dB
3
6
12
(1-9)
$3.52
3.52
3.93
B
Solder Back Indoor/Outdoor
Directional Couplers and Taps
Fixed Mini-Type
Attenuator Pads
Voltage Blocking Coupler
A
(10-up)
$17.12
(10-49)
$2.98
3.32
3.56
Order #
33-341
(1-49)
$2.72
120
www.MCMelectronics.com /1-800-543-4330
Blonder Tongue offers a complete line of professional
quality indoor/outdoor couplers and tapoffs covering
frequencies up to1000MHz. These products are
available in both an L or T style cases. The variety of
loss values offered guarantees that they have the right
product for your application. These products feature a
durable outdoor rated soldered back, cast housing,
which shields against EMI and RFI disturbances.
Order #
Loss (dB)
A. L Style-SCW models
33-2941
4
33-2946
6
33-2951
9
33-2956
12
33-2961
16
33-2966
20
33-2967
24
33-2968
27
33-2969
30
B. In-Line Style-SRT models
33-2971
4
33-2976
6
33-2981
9
33-2986
12
33-2991
16
33-2996
20
33-2997
24
33-2998
27
33-2999
30
(1-9)
(10-up)
$2.62
2.62
2.62
2.62
2.62
2.62
2.51
2.51
2.51
$2.35
2.35
2.35
2.35
2.35
2.35
2.28
2.28
2.28
2.51
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.51
2.28
2.35
2.35
2.35
2.35
2.35
2.35
2.35
2.28
(50-up)
$1.97
2.82
3.21
Follow us on:
&
AUDIO/VIDEO
Audio/Video
Distribution
RF Splitters
D
E
A
B
C
D
Section
7
C
Vertical Splitters
•Nickel plated zinc die-cast housing •RFI shielding
•2GHz splitters feature one power passive port marked
on the splitter
A
Description
(1-9)
(10-up)
2-way
3-way
4-way
6-way
8-way
$3.22
4.23
5.09
6.35
7.36
$2.70
3.78
4.19
5.40
6.48
2–way
4–way
6–way
8–way
6.25
10.49
16.49
19.49
5.88
9.36
13.47
16.04
B
C
D
E
Indoor Splitters
High Frequency Horizontal Satellite Splitters
High frequency splitters used for satellite and DSS
applications. Power passive to operate in–line amps
and multi-switches. Bandwidth: 5MHz~3000MHz.
Fig. Order #
1 Port Passive
A
33-4350
B
33-4355
C
33-4360
D
33-4365
E
33-4370
All Ports Passive
A
33-4375
B
33-4380
C
33-4385
D
33-4390
E
33-4395
High Frequency Vertical Satellite Splitters
High frequency vertically oriented splitters used for
satellite and DSS applications. Power passive to operate
in-line amps and multi-switches. Bandwidth:
5MHz~3000MHz.
Fig. Order #
1 Port Passive
A
33-10235
B
33-10236
C
33-10237
D
33-10238
E
33-10239
All Ports Passive
B
33-10241
C
33-10242
D
33-10243
E
33-10244
Description
(1-9)
(10-up)
2-way
3-way
4-way
6-way
8-way
$6.25
8.37
9.08 16.99
17.99
$5.93
7.90
8.63
15.78
16.77
3-way
4-way
6-way
8-way
9.08
9.38
16.99
20.49
8.76
8.89
15.78
18.98
In-Line Splitters
Description
2-way
3-way
4-way
(1-9)
$3.22
4.07
5.24
(1-9)
(10-up)
2-Way
3-Way
4-Way
6-Way
8-Way
$6.25
8.15
9.08
17.49
17.99
$5.99
7.34
8.31
16.19
16.76
2-Way
3-Way
4-Way
6-Way
8-Way
6.25
8.47
9.30
17.49
17.99
5.99
7.56
8.52
16.43
16.76
B
Order #
33-2900
33-2905
33-2910
33-2915
Order #
33-10245
33-10246
33-10247
Description
2-way
3-way
4-way
A
(ea.)
$3.52
3.93
4.03
(2-up)
$2.38
3.79
3.86
B
Fig.
A
B
C
Order #
33-2130
33-2135
33-2140
Type
2-way
3-way
4-way
(1-9)
$2.13
3.02
3.45
(10-up)
$1.88
2.50
3.04
DC & IR
Passing Yes Yes No B
(10-up)
$0.95
1.68
–
6.54
ONLY
$5.34
7.87
10.99
A
High-Frequency Splitters
•Heavy-duty, die-cast design •Power passive
•Low thru-loss •950MHz~1750MHz
•For use with satellite systems and other
high-frequency applications
Fig.
A
B
C
(1-9)
$1.00
1.81
3.32
6.66
The Channel Plus
bi–directional
splitter/combiners
provide a 1GHz
bandwidth and are ideal for antenna and coaxial cable
operations. It can be used to split a signal from a
source or combine signals from multiple sources onto
one coax run.
High Frequency RFI Splitters
Fig.
A
B
C
Description
2-way
3-way
4-way
8-way
Splitter/Combiner
DIRECTV® compatible high frequency performance to
3GHz. •Tin-plated zinc die-cast housing with soldered
back to achieve RFI -130dB •Waterproof and airtight
up to 30 P.S.I. with 4.55mm grounding hole and
stainless steel screws •Low thru loss and high isolation
with patent pending 360° insert pin. Bandwidth:
5MHz~3000MHz.
•For use in applications where
additional shielding is needed
•100dB case design exceeds
FCC requirements for RF
shielding •25% more zinc
content than standard splitters •Case thickness
increased by 50% to obtain very good RFI
performance •Mounting tabs with screws
and grounding block •5MHz~1000MHz
frequency response
(10-up)
$2.70
3.67
4.86
Fig.
A
B
C
D
Insertion Order # Description Loss 2512 2–way 3.5 dB 2514 4–way 8.0 dB 2538 8-way 12.0 dB C
RFI Splitters
The in-line port
design of these
splitters helps to
keep cables
organized and makes
them perfect for
installations in
crowded areas.
Nickel plated
zinc die-cast
construction. Bandwidth: 5~1000MHz.
Order #
33-4865
33-4870
33-4875
A
Description
Performance to 1000MHz. 2, 3, 4 and 8 way models.
Die-cast housing. RF shielding. Mounting tabs
and grounding blocks.
Order #
33-0035
33-0040
Description
2-way
4-way
(1-9)
$4.03
6.25
(10-up)
$3.87
5.99
2.4GHz Four Way
Bi-Directional Splitter
•High-grade circuitry allows
the connection of components
with minimal signal loss •Maximum transfer of all
your RF signals including higher digital frequencies
means quality reception and excellent picture output
•Splits a 75Ω coaxial signal from cable TV, an antenna
or a VCR for connection to two TVs/VCRs
•Frequency: 5MHz~2.4GHz •Gold-plated input/
outputs for reliable connectivity •Dual-grounded
connections •Precision cast body
Order #
DT44SP
www.MCMelectronics.com /1-800-543-4330
ONLY
$12.49
121
7
Order #
5~1000MHz
33-4880
33-4885
33-4890
33-4895
33-4900
5~2150MHz
33-7140
33-7150
33-7155
33-7160
B
A
Section
7
AUDIO/VIDEO
Audio/Video
Distribution
Bi-Directional CATV Amplifiers
Digital
amplifiers with
return path for
use with CATV
convertors (pay
per view) and
cable modems.
Soldered back
ensures isolation and signal integrity. Specifications:
Bandwidth: 54~1000MHz. Noise figure: 3.5dB. Power:
12VDC, 250mA via included adapter (using “F” cable).
7
50MHz~1HGz
Broadband
Amplifier
Ultra low noise
amplifier employs
high output push-pull design, with frequency range
of 50MHz~1GHz, providing up to 34dB gain.
Additionally, a passive 5~42MHz return path enables
use with cable TV systems that utilize interactive digital
boxes and broad band internet service. Variable gain
and tilt adjustments allow installer to compensate for
a wide range of cable lengths. Features: •Wide forward
frequency range: 50MHz~1GHz •Ultra low noise figure
•Push-pull SMD strip line circuit design •-20dB input
and output test •115VAC operation, no space
consuming AC adapter Specifications: Forward
frequency range: 54~1000MHz •Forward gain: 34dB
•Gain adjustment range: 15dB •Max input level +5 dB
•Max ouput level: 39dB •Return frequency range:
5 ~ 42MHz •Return insertion loss: 2.5dB •Power
requirements 117VAC, 60 Hz, 6 W •Dimensions
2" (H) x 33/8" (W) x .8" (L)
Order #
33-2675
#DA-550BID
(1-9)
$156.00
(10-up)
$148.00
High Headroom
Distribution Amplifier
The DA-550s can handle an
extremely wide range of
input signals from both
NTSC and digital HDTV.
With outputs to eight
televisions, coax runs up to
150', three inputs, one from
a CATV or antenna and two
from modulators, the
DA-550 is the heart of a
multi-room distribution
system. The DA-550BID
offers a 5~42MHz return
path for bi-directional
#DA-550HHR
communication for use with
cable modems and pay-per-view applications. The
DA-550HHR is used with high performance antenna
applications for off air digital and NTSC signals.
Additional features: IR engine, remote power and
expandable outputs.
Order #
DA-550BID
DA-550HHR
#30-2124
#30-2125
Order # Forward Gain Reverse Gain (1-9) (10-up)
33-7110
15dB
0dB (Flat)
$43.49 $39.51
33-7111
15dB
10dB
48.49 43.38
33-7115
15dB
15dB
48.49 44.46
UHF/VHF/FM 25dB
Amplifier
#30-2130
#30-2135
Distribution Amplifiers
•Commercial grade distribution amplifiers can be
used for HDTV, CATV, off-air, analog, and digital
RF distribution •Weather sealed housings •Average
noise figure: 2.8dB •50~1000MHz
Order #
30-2124
30-2125
30-2130
30-2135
Mfr. #
3410
3412
3414
3418
Description
1-way
2-way
4-way
8-way
Gain
15dB
11.5dB
8dB
4dB
ONLY
$35.49
42.49
47.49
60.99
RF Distribution Amplifier
For systems with up to eight
TV outlets and cable lengths
up to 150'. The DA-8200
series provides outputs to
eight televisions, three inputs
from an off–air antenna or
CATV and two modulator
locations. May be remotely powered from up to 75'
away by using a remote wall plate model 2010 or any
5500 series or SVM series modulator.
Order #
DA-8200BID
DA-8200HHR
Description
Bi–directional amplifier
High head–room amplifier
ONLY
$171.00
171.00
ONLY
$171.00
171.00
Features: •Low noise
•Lightning protection
•AC power indicator
•Switchable FM trap
•Low cost Specifications: •Bandwidth: 54~900MHz
•Gain: VHF, 25dB; UHF, 22dB •Maximum input: VHF,
18dB; UHF, 16dB •Maximum output: 40dB
(54~800MHz) •Noise figure: VHF, 5dB; UHF, 7dB
•75ohm input/output •Power requirements: 115VAC;
60Hz •Dimensions: 57⁄8" (W) x 15⁄8" (H) x 3" (D)
Order #
33-0450
(1-9)
$28.49
(10-up)
$27.64
UHF/VHF/FM
36dB Amplifier
Features:
•Low noise
•Two switchable
FM traps
•Separate gain
controls •AC power indicator •50dB output capability
•-20dB monitor output •Fuse protected Specifications:
•Bandwidth: 54MHz~108MHz, 174MHz~216MHz,
470MHz~812MHz •Gain: VHF, 31dB; UHF, 36dB
•75ohm input/output •Power requirements: 115VAC;
60Hz •Dimensions: 83⁄4" (L) x 17⁄8" (H) x 33⁄4" (D)
•Fuse protected
Order #
33-0890
(1-9)
$95.99
(10-up)
$88.97
Four-Way
Amplified Coupler
•50MHz~550MHz
bandwidth •1~3dB
gain •117VAC power
required •One input,
four outputs
1
1
•Dimensions: 3 ⁄2" (W) x 2 ⁄4" (H) x 11⁄2" (D)
Order #
33-1475
(1-9)
$13.99
(10-up)
$12.61
Broadband Structured Wire RF Amplifiers
Compatible with the market leader of structured wiring panels, these 5~1000MHz,
DOCSIS® compliant amplifier modules are the ideal drop-in replacement
for CATV in-home signal distribution. Improve your multimedia application with
the latest broadband technology for HDTV QAM signals. Features include
a durable, salt-spray-resistant housing, weather-sealed
“F” ports, and exceptional surge performance.
Order #
33-10225
33-10226
Multiple Dwelling Amplifier
A
Specifications: RF: •Frequency range: 47~550MHz
•Gain: 32dB •Noise figure(a): 8.0dB •Output level:
+44dBmV •Gain control range: 15dB •Slope control
range: 10dB •Impedance all ports: 75ohm General:
•Power requirements: •Voltage(d): 117VAC, ±10%, 24
•Frequency: 60Hz •Power: 13W •Mfr. #ACA 30-550
Order #
33-2875
122
Description
6 output
8 output
B
C
ONLY
$302.00
www.MCMelectronics.com /1-800-543-4330
Gain
+6.5dB gain
+10.0dB gain
ONLY
$88.99
101.00
RF Amplifiers
Low noise VHF/UHF/FM signal amplifiers. Variable gain control
–10dB. Built–in FM trap (-20dB). Specifications: Frequency range:
40~862MHz. Noise figure: <7dB. Power: 120VAC.
Fig.
A
B
C
Order #
33-8715
33-8720
33-8725
Outputs
1
2
4
Gain
30dB
25dB
20dB
Follow us on:
(1-9)
$18.49
19.49
20.49
&
(10-up)
$17.34
17.68
18.58
AUDIO/VIDEO
Audio/Video
Distribution
A
Sirius Ready
•Utilize existing cable TV wiring to distribute satellite
radio antenna signal •Designed to work with PRO-500
(#33-10620) and PRO-600 (#33-10645) antennas
•No external power supply required •All jumpers
and adapters included •Sold as two separate input
and output pieces
Fig.Order #
Mfr. # Description
A 33-10705 SRC-DI Cable/XM diplexer in
B 33-10710 SRC-DO Cable/XM diplexer out
ONLY
$45.49
45.49
XM/Sirius Radio Ready Pro Pack
•Everything needed to add Sirius to any “XM Ready”
or “Sirius Ready” receiver using up to 200' RG-6 cable
Kit includes: •Pro-500 outdoor antenna •“F” to SMB
3' adapter cable •Sirius SC-H1 tuner or XM CMP2000
tuner and dock
Order #
33-10670
33-10715
Mfr. #
SRR-5
XMR-1
For receivers
“Sirius ready”
“XM ready”
ONLY
$222.00
212.00
Order #
33-10600
ONLY
$48.49
•Designed to power
line amplifiers and XM
Satellite Radio amplified
antennas •This unit consists of a
5VDC regulated power supply for use in RG-6
networks designed to distribute XM satellite radio
signals •Mfr.# PS-1
Order #
33-10625
ONLY
$80.99
ONLY
$132.00
Dual Mode Satellite Radio Antenna
•High-quality future proof home antenna for
simultaneous reception of both XM and Sirius Radio
•70 beam-width for easy alignment and mounting
Drives up to 200' of RG-6 cable (not included)
•Azimuth and elevation adjustments for optimum
aiming •Two-stage high-quality filtering for rejection
of out-of-band interference •High- quality aluminum
mount •Includes wall or pole mount brackets
•Mounts to any horizontal or vertical surface
or pole up to 2'' diameter.
Order #
33-10645
ONLY
$101.00
Amplifier Satellite Radio Splitter Kit
•Operates up to four or eight satellite radios
from a single antenna with this amplified splitter
•Includes all adapters and accessories •Uses standard
RG-6 cable (not included) •Maintains proper RF link
budget for the radio •Splitter loss at 2.35GHz has
been compensated by an internal low-noise amplifier
powered by DC voltage supplied by radios •Splitter
has 8dB of gain •Adapters used to convert XM
or Sirius SMA and SMB connections into
an “F” connection to mate with RG-6 cables
Order #
33-10675
33-10680
Mfr. #
SR-4
SR-8
Description
Four-way kit
Eight-way kit
ONLY
$101.00
262.00
#33-10605
Satellite Radio Multiplexer
•The components you need to multiplex the output of
a satellite radio antenna onto the RG-6 from a DBS
system •Supports cable runs up to 200' •Designed for
the PRO-500 (#33-10620) and PRO-600 (#33-10645)
antennas •Mfr. #SRDBS
Order #
33-10700
ONLY
$64.95
#33-10695
Wide Band
Four-Way Passive Splitter
•Designed for all AM/FM, HD radio, broadcast TV,
cable TV, satellite radio, and satellite TV signals •Passes
signals from 500KHz to 2.4GHz •Insertion loss: 12dB
•Use in conjunction with #33-10695 for lossless splits
Order #
Mfr. #
Description
ONLY
33-10690 MBS-4 4-way splitter
$80.99
33-10695 MBA-12 Line amplifier for #33-10690 85.99
This antenna
extension cable is designed to
work with any satellite radio antenna (purchsed
separately) to extend the cable length 100' (lengths up
to 300' can be achieved by cascading three cable kits).
Kit includes: •SMB to “F” adapter •High-gain amplifier
•100' premium RG-6 cable with “F” connectors •3'
female to SMB-plug adapter cable •Two coax seals
•Mfr. #PRO-100
Order #
33-10615
ONLY
$70.99
#33-10650
#33-10655
•Adapters used to convert XM or Sirius SMA and
SMB connections into an “F” connection to mate
with RG-6 cables
Order #
33-10605
33-10610
33-10650
33-10655
33-10660
Satellite
Radio RG-6
Extension
Kit
#33-10690
SMA/SMB
to “F” Adapters
Description
Qty. ONLY
3' SMB-plug to 1
$18.49
“F” female adapter cable
3' SMB-plug to 10 172.00
“F” female adapter cable
SMA male to “F” female adapter 1
23.49
SMB male jack to “F” male adapter 1
16.49
SMB male jack to “F” male adapter 10 151.00
High Gain Line Amplifier
•For use in satellite radio distribution networks to
overcome loss in cables and splitters •Gain: 16dB @
4.5VDC •Current consumption: Typically 10mA @
4.5VDC •Frequency range: 2320~2345MHz •Noise
figure: 4dB max •Mfr. #SBA-1
Order #
33-10640
www.MCMelectronics.com /1-800-543-4330
ONLY
$20.49
123
7
•Kit to permit the use of standard RG-6 cable with
satellite radio antennas •When used with the included
amplifier, this kit can extend the antenna cable up to an
additional 125' •Add the flexibility of RG-6 cable Kit
includes: •SMB to “F” adapter (to mate with antenna
cable) •High-gain amplifier •“F” to SMB adapter cable
(to mate with radio) •Mfr. #EXTANT-01
•Receives XM or Sirius
satellite radio services
•Ideal for commercial,
high-end home and
multi-dwelling unit installations •Optimized for
interference/multipath rejection and high gain reception
of satellite radio signals •Antenna can drive up to 200'
of RG-6 cable (not included) •Mounts to any horizontal
or vertical surface or to a 13⁄4" diameter pole •High gain
12dBi antenna (5dB more than standard antennas)
Includes: •Built-in two-stage ultra high low noise
amplifier •Wall and pole brackets and accessories
•3' “F” female to SMB plug adapter cable to mate
with radio •Mfr. #PRO-500
Order #
33-10620
Power
Inserter Kit for
XM Satellite Radio
Satellite Radio RG-6 Cable Extender Kit
7
Professional High
Gain Satellite Radio
System for XM
and Sirius
XM Ready
B
Cable TV and Satellite Radio Multiplexer
Section
Section
7
AUDIO/VIDEO
Audio/Video
Distribution
HDTV Indoor
Amplified
Antenna
Ideally suited for
indoor HDTV
(UHF)off-air
reception, this
antenna features
a low-profile boom design, rotational elements for
improved directional gain, and a 7~13dB adjustable
gain control (power adapter included).
Back
Set-Top Digital Television Converter
4Composite and S-Video output
4“Scan Add” function
Compact tuner receives over-the-air digital television
broadcasts, and is compatible with virtually any older
model analog television or recorder. Internal RF
modulator will place signal on CH3 or CH4 on
televisions without composite video inputs. Features:
•Compatible with all 18 ATSC signal formats
•On-screen electronic program guide support •Line level
audio and composite video output •Coax antenna input
•Coax antenna CH3 / CH4 output •Includes 27
button remote
Compact tuner receives over-the-air digital
television broadcasts, and is compatible with
virtually any older model analog television or
recording device. Internal RF modulator can place
signal on CH3 or CH4 on televisions without
composite or s-video inputs. Features: •Compatible
with all 18 ATSC signal formats •Line level audio
and composite outputs, as well as s-video •On-screen
electronic program guide support •“Scan add” feature
adds channels to the existing list (instead of
overwriting), allowing simple integration with an
antenna mounted on a rotor •Mfr. #CM-7000
Order #
30-2202
Order #
30-2122
7
Set-Top Digital Television Converter
ONLY
$50.49
ONLY
$90.99
HDTV Indoor Antennas
Passive Indoor Flat HD Antenna
•Paintable flat antenna is designed to disappear into
any décor •Can be hung, lay flat, or stood vertically
•Advanced 360° reception eliminates need to adjust
antenna while changing channels •Designed for HD
reception and receives UHF/VHF/FM signals •Includes
coax cable •Mfr. #ANT1500
Order #
30-2175
ONLY
$35.49
Terk indoor HDTV directional antennas are optimized for HDTV reception. Both UHF and VHF elements are uniquely
designed for reception of all available HDTV off-air
broadcasts (channel 2~69). Highly directional UHF
elements reduce signal interference and improve
average return loss for better reception and superior
performance.
Order #
30-2000
30-2005
Mfr. #
HDTVi
HDTVa
Description
Non-amplified
Amplified
ONLY
$40.49
58.99
Order #
30-2100
ONLY
$20.49
TM
UHF/VHF/HDTV
Indoor Antenna
•An amplified UHF/
VHF antenna that will
receive all FM, DTV,
and HDTV signals
•Adjustable amplifier
for better control on
reception gain •“F” type
input for connecting
external antenna, VCR, cable, or other source, or used
stand-alone •Great for areas where an outdoor antenna
is required for some stations, but nearby stations that
are too strong require an indoor antenna •Frequency
range: 40~860MHz •Max noise: 6dB •Max
amplification: 28dB •Power source: 120VAC
or optional 12VDC
Order #
30-2160
MSRP
$24.95
ONLY
$15.49
Variable Attenuator
For those living very close
to transmitting towers,
problems with multipath
interference can occur because the signals are so strong
that they bounce off nearby buildings and other objects
and cause multiple images to appear on one’s TV
screen. This attenuator allows users to dial down the
signal to reduce problems associated with this multipath
and overloading interference.
Order #
30-2118
ONLY
$12.49
Basic Slim Antenna
•Receives HD and DTV signals •Super slim design can
be laid flat or hung horizontally on wall, even behind
your television •Includes coax cable •Mfr. #ANT1000
Flat Black HD Antenna
• Receives local digital TV broadcasts and FM radio
signals •360° reception patented technology eliminates
constant adjustment •Enhances reception by amplifying
weak signals with a built-in ultra low noise amplifier
•Can be hung on a wall or lie flat •Coax cable included
•Mfr. #ANT1450B
Order #
30-2170
Order #
30-2165
ONLY
$26.37
ONLY
$10.49
AM Loop Antenna
INDOORtenna™
HDTV/UHF
Antenna
•Popular replacement
AM antenna used on
most stereo receivers
•181⁄2" lead length
•300ohm impedance •Antenna has two pin
quick connect for equipped systems •For systems
with push terminals or screw terminals, simply
cut and strip the ends of the antenna wire
for your application
•Excellent indoor
HDTV/UHF
reception •Passive
antenna design
allows for increased forward gain while minimizing
interference from side and rear •Place on set-top
or mount on the wall •Includes 110" of coax cable
•Dimensions: 10" (L) x 11.5" (W) x 8" (H)
•Mfr. #CM-4040
Order #
30-660
(1-9)
$3.52
Order #
30-2150
124
www.MCMelectronics.com /1-800-543-4330
(10-up)
$2.96
FM Dipole Antennas
These high-quality
FM dipole antennas can
be used for many newer
FM tuners and receivers.
Available in three
configurations: 300ohm
spade terminals, 75ohm male “F” connector and
75ohm female PAL connector. These antennas are
constructed from high-quality 300ohm twin–lead and
perform significantly better than the OEM supplied
straight wire or a split two conductor antennas
providing highe-quality FM reception.
Order #
30-1530
30-1535
30-110
Description
Male “F” connector
Female PAL connector
Spade terminals
(1-9)
$2.31
2.11
2.41
ONLY
$26.49
Follow us on:
&
(10-up)
$1.61
1.56
2.07
AUDIO/VIDEO
Audio/Video
Distribution
Compact HDTV Antenna
•Extremely low profile design
can be mounted indoors or
outdoors •Extremely low noise
amplifier is designed for the
latest digital and highdefinition television reception
•20dB gain •UV resistant case
Includes: •Antenna •Flexible
arm mounting base •Power
inserter •AC adapter •Coax
cable •Mounting hardware
Order #
30-2205
HDTV Amplified
Outdoor Antenna
ONLY
$25.49
The Terk HDTVo is an innovative,
compact, amplified outdoor antenna that features
powerful high gain, and offers versatile installation
flexibility. Its unique design incorporates a highly
directional log periodic antenna array and a pair of
curved elements that combine to capture and focus
HDTV signals. Mount flush to the side of a building,
or use the included mulit-mount mini-mast and base to
install virtually anywhere.
UHF Indoor/Outdoor Antenna
Order #
30-2020
AM/FM Q
Order #
MANT940
ONLY
$37.49
TERK’s premium
amplified indoor
AM/FM antenna.
The AM/FM Q
features TERK’s
unique Pin-Dot
Pre-Tuning that
zeroes in on even hard-to-get stations by tuning the
antenna to the station’s frequency. Mfr. #AF-1.
Order #
30-1550
FM Turnstyle
•Offers the gain of a folded dipole
with an omni–directional pattern
•Works in areas where stations are
situated in many directions
Order #
30-855
(ea.)
$70.99
(2-4)
$68.36
(5-up)
$65.04
TV55 Antenna
The TV55 indoor/outdoor
amplified antenna is optimized
for HDTV reception. The TV55’s
helical coil technology and patented dual–
mode ultra–low–noise amplifier provide clear,
powerful reception of HDTV and analog VHF/UHF
broadcast signals, and its slim-profile design allows
easy mounting under a windowsill, on a rooftop, on a
wall or in any number of locations inside or outside a
home. The TV55 includes cables and weatherproof
stainless steel connectors, for easy integration with
satellite systems. The kit combines local and satellite
signals into a single RG-6 coaxial cable, eliminating
the need to run an extra wire from the dish to the
home. Accessories included: (1) power injector with
110VAC to DC power adapter, (1) 1⁄4-20 x 11⁄2" hexhead bolt, (1) 1⁄4-20 21⁄2" hex-head bolt, (1) mast
mount base, (2) 1⁄4-20 x 3⁄4" hex-head bolts, (1) mast
mount cover, (1) 1⁄4-20 wing nut, (2) window mount
brackets (2-piece assemblies), 1⁄4"-20 hexagon nuts, (2)
wall mount cam-lock units, (2) #10 x 21⁄2" flat-head
screws, (1) channel insert, (2) #8 x 11⁄2" flat-head
screws, (1) 93⁄4" flat coaxial cable, (2) 1⁄4" split washers,
(1) 36" RG-6 coaxial cable, (2) #10 plastic wall
anchors. Mfr. #TV-55.
Order #
30-1525
AM Advantage
ONLY
$22.49
The AM Advantage
antenna is a passive,
fully adjustable indoor
AM antenna designed
for extended range
capability. The antenna
is intended to receive
AM frequencies
530KHz~1600KHz for
local and distant AM reception. The antenna features
Pin–Dot™ Pre Tuning system which allow the user to
adjust the antenna and match it to the specific
frequency. Mfr. #ADVANTAGE.
Scanner Antenna
Covers VHF/UHF public service bands
30~1300MHz. Includes 300 to 75ohm
matching transformer and 50' RG-6
coax cable.
Order #
30-1380
ONLY
$131.00
ONLY
$44.99
Order #
30-1395
ONLY
$45.49
7
ONLY
$78.99
FM PRO 50
FM PRO is the clear choice for the FM enthusiast.
Designed to provide exceptional long-range FM
reception, it may be mounted indoors or outdoors for
a totally unobstructed installation. #30-1205 has a
weather-proof housing and is easily installed in an
attic, exterior side of the home or indoors in a closet,
garage or interior wall. New Advanced Capture
Circuitry™ (ACC) ensures that strong signals are
locked in and weaker broadcasts are received with less
noise. Terk’s exclusive Dual Drive Amplifier boosts
signals above noise and interference, using a
DC–driven phantom power supply that is easily
connected to your receiver.
Order #
30-1205
ONLY
$101.00
AM/FM Tower
AM/FM HD Radio Antenna Kit
•Professional quality AM/FM/HD radio antenna
•Receive stations from up to 90 miles in all
directions •All signals combined on a single RG-6
cable up to 200' (not included) •Includes surge
protector and all required adapters and jumpers
•Pole or wall mount •No preamplifiers required
•4' omni-directional monopole requires no ground
plane •Mfr. #AFHD-4
Order #
33-10630
ONLY
$161.00
Positioned vertically, the tower receives
signals from all directions with equal
strength. Used horizontally, it becomes
highly directional to pull in weaker and
more distant stations. It also distinguishes
between signal reflections and the main
signal to eliminate overload and multipath
difficulties. Specifications: FM stereo
section: •Amplifier gain: Variable
0dB~25dB •Impedance: 75ohm adaptable
to 300ohm input with included matching
transformer •FM operating band:
88~108MHz AM stereo section: •AM
operating band: 500~1700KHz •AM gain:
15dB •Range: 360° 17" (H) x 31⁄4" (W)
Order #
30-1110
(1-9)
$22.49
(10-up)
$20.90
Omni–State Omni–
Directional Antenna
The Omni–State antenna
provides excellent
reception of VHF
and UHF channels
in most viewing locations.
Measures 21" in diameter
and has a 20dB built–in
amplifier. Operates on
120VAC with the
supplied adapter.
Order #
30-1335
www.MCMelectronics.com /1-800-543-4330
ONLY
$78.99
125
7
Easiest and best solution for urban/
surburban UHF DTV (digital TV)
reception. Perfect alternative to
conventional outdoor antennas. Features:
•Built-in optimum gain amplifier, 18dB
UHF, with low noise circuitry, under
3.5dB, for best possible DTV performance
•Efficient flat panel UHF array, up to 40
miles range •Compact yet effective size, 5"
x 10" •Easily mounts on wall, mast or
railing •Can be used with rotor (optional,
mast only) •Ideal for RV or boat. Includes
20' cable, power injector, power supply,
and flexible mounting kit.
Section
Section
7
AUDIO/VIDEO
Audio/Video
Distribution
•Consistently powerful
reception gain across
the entire DTV spectrum
•Advancements in efficiency
allows up to 98% of the
available broadcast signal
to actually reach the incoming
antenna cable rather than
#30-2102
being lost to impedance
mismatches •Compact
#30-2104
and easy to mount •Easy to
assemble •Unmatched power and efficiency through advanced
computer design •Engineered for extra strength and durability •UHF and
DTV spectrum (470~806MHz) •Multidirectional, up to 70° of beam width
#30-2106
Order #
Model #
C1
C2
C4
Range
Miles
Dimensions
(H) x (W) x (D)
Gain
Weight
ONLY
0~30 0~50 0~65 10" x 10" x 4.5"
20" x 10" x 5"
19" x 20" x 4.5"
8 dBi
10.2 dBi
14.8 dBi
2.5 lb.
3.5 lb.
8.5 lb.
$76.49
88.99
141.00
TM
UHF/HDTV
Outdoor Antenna
•Directional outdoor antenna is optimized to pick up
UHF signals for digital television and high-definition
television broadcasts •Frequency range: 460~862MHz
•30 elements •75ohm “F” type connection •20dB
•Up to 50 mile range
Order #
30-2155
MSRP
$39.95
ONLY
$20.49
7
30-2102
30-2104
30-2106
ClearStream™
DTV Antennas
#30-2071
#30-2145
#30-2140
#30-2070
These powerful, weather-resistant, outdoor antennas are ideal for medium to long range applications that require
the gain of the antenna to be concentrated in one direction. The Yagi style design effectively rejects off axis signals
from structures that cause multi-path interference, and the corner reflectors on the back of the antennas improve
the forward gain of the antenna resulting in exceptional performance across the entire UHF spectrum (channels
14~69).
Order #
Description
30-2070
Compact, 15-element, short-range
30-2071
Mid-sized, 43-element, long-range
30-2072
Large, high-gain, 91-element, long range
Range
miles
1~30
15~60
50~70+
Ultra-Hi Crossfire™
HDTV/UHF/VHF/FM Antenna
#30-2072
Uni-Directional HDTV UHF Antennas
Gain
db
11.0
15.7
16.7
Dimensions
(H) x (W) x (L)
14" x 13" x 35"
19" x 18" x 62"
22" x 20" x 93"
ONLY
$50.49
57.99
85.99
•Exceptional outdoor reception of VHF/UHF channels
2~69, and FM •Deep fringe rated •Connects to either
75 or 300ohm downlead •Directional beam width of
approximately 30°
Order # Mfr. #
Max Range
30-2140 CM-3671 100 miles
30-2145 CM-3679 60 miles
Dimensions
(L) x (W) x (H)
ONLY
173" x 110" x 35.4" $191.00
122" x 110" x 35.4" 131.00
Multi-Directional HDTV UHF Antennas
Order #
Description
Range Miles
Multi-directional antennas are designed
to work in locations where the transmitters
for digital stations are spread apart. These
popular HD antennas utilize a bowtie design
that provides a strong gain across the entire
UHF spectrum (channels 14~69). They
function incredibly well in areas where
flexible aiming is required and feature
a weatherproof construction that resists
extreme wind loading.
ONLY
Gain
Dimensions
30-2065
30-2066
30-2067
Indoor/outdoor, low-profile, short range
Outdoor, most popular, mid-range
Outdoor, high-gain, long range
1~30
15~55
50~70
11.4db
13.7db
15.8db
#30-2065
#30-2067
#30-2066
12" (H) x 19" (W) x 4" (D)
29" (H) x 19" (W) x 4" (D)
29" (H) x 42" (W) x 4" (D)
$37.49
55.99
80.99
#30-840
UHF/VHF/FM Antennas
•300ohm output, includes 75ohm transformer
Order # Description
Boom Length ElementsONLY
30-840 Colorstar 480
150"
48 $80.99
30-850 Color King 5884
58"
25
30.49
#30-2110
Masts
16 gauge corrosion protected mast ideal for television
and communication antennas. 5' section swagged at
one end. 21⁄2' section ideal for use above rotator.
Order #
30-1080
30-935
Size
21⁄2'
5'
ONLY
$7.06
12.49
•Versatile all-in-one mount that can be used
with antennas or satellite dishes •Can be
mounted on the roof, wall, chimney or any
other flat surface •J-pipe is reversible from
mounting foot for a variety of positioning
options •Gray weatherproof coating
•38" mast height •15⁄8" mast diameter
(1-9)
$13.99
(10-24)
$11.82
(25-49)
$11.51
•18 gauge, 6 strand heavy-duty guy wire •Vinyl coated
to reduce effects of weather •Length: 100'
Order #
30-1055
126
#30-2112
Universal J-Mount
J-Pipe Mount
Order #
33-10915
Guy Wire
#30-850
ONLY
$12.99
www.MCMelectronics.com /1-800-543-4330
(50-up)
$10.54
satellite dish mounting
•Pivoting foot mount offers
the ideal solution for
mounting nearly anywhere,
including side of house, roof
top, deck rail, or any other
flat surface •Pipe is reversible
from plate for more mounting
angle options •20" mount is
ideal for the ClearStream antenna series Includes:
•J-shaped mounting pole •Mounting bracket
•Expansion bolts
Order #
30-2110
30-2112
Size
30"
20"
Follow us on:
ONLY
$18.49
16.99
&
AUDIO/VIDEO
Audio/Video
Distribution
3' Tripods
•Used for
mounting TV
antennas and
satellite dishes
permanently or
for temporarily
use •Fits masts up
to 15⁄8" (included
#33-10910
#33-10905
with portable
unit) •Standard tripod uses six bolts to tighten down
on mast, and can be anchored on all legs with three lag
bolts each •Portable unit has integrated compass and
bubble level, folds up for easy transportation, and
secures to ground with anchor screw
Order #
Description (1-9) (10-24) (25-49) (50-up)
33-10905 Standard $18.49 $16.15 $15.39 $15.23
33-10910 Portable
17.49 15.50 14.89 14.43
TennaMount
A strong stable mounting
system that supports both
DBS and VHF/UHF
antennas in one convenient
location. Installs quickly
and easily to the side wall
of a building, and adjusts
easily to roof overhangs.
It can be wired with back–
to–back splitters so all
DBS, VHF and UHF
signals travel on one RG-6
cable. All mounting
hardware supplied.
Order #
33-2630
Section
7
SnapToggle®
Heavy-Duty Anchors
ONLY
$54.99
Satellite Dish Pipe Adapter
•Adapt existing pipes and masts to work with satellite
dish mounts •Heavy gauge steel •1.66'' outer diameter
•Tightens with two bolts
Non-Penetrating Roof Mount
•Perfect solution for commercial buildings and other
flat roofs •For 18" and 24" dishes •Uses six 8" x 8" x 16"
cinder blocks for stability •Powder coated for weather
durability •Angle iron frame
Order #
33-10565
Order #
33-10890
(1-9)
$2.11
(10-24)
$1.91
(25-49)
$1.76
(50-up)
$1.59
Order #
28-11025
28-11026
28-11030
28-11031
Mfr. #
43321
25014
43311
25013
Description
Quantity
10pk
w/ 1⁄4" x 20 bolts
w/o 1⁄4" x 20 bolts
50pk
3
w/ ⁄16" x 24 bolts
10pk
w/o 3⁄16" x 24 bolts
50pk
ONLY
$9.28
30.99
9.28
30.99
Pitch Pad Kit
ONLY
$32.99
•Pitch pad and lag bolt
kit •Pads reduce risk of
water leakage •Use when
mounting antennas on roof
•Contains six lag bolts
B
Order #
30-940
A
ONLY
$3.09
D
Siding Mount Block
•Clean and protective solution for mounting a satellite
dish to vinyl siding •Prevents insect infestations and
weathering •Comes in three styles to fit most aluminum
and vinyl siding •White
C
Heavy–Duty Antenna Mounting Accessories
•Heavy–duty mount for masts up to 1 ⁄2" outer
diameter •Made of all steel construction
•Triple coat corrosion protection
1
Fig.
A
B
C
D
Order #
30-895
30-910
30-915
30-1160
Description
Roof mount
“Z” chimney mount
“Y” chimney mount
Vent pipe mount
A
Order #
33-10560
33-10561
33-10562
Description
Fits double 5⁄8 lap 4" siding
Fits 1⁄2 or 5⁄8 lap 5" siding
Fits Dutch lap siding Dimensions ONLY
10" x 7"
$8.99
12" x 8"
8.99
12" x 8"
8.99
ONLY
$6.72
1.61
24.49
11.49
Fig.Order #
A 30-1030
B 30-1035
C 30-1045
Widely used for many types of SATV and security
installations. Kit contains: •100 1⁄4" pan-head screws
•100 #8 plastic anchors •One masonary drill bit (1⁄4")
Order #
28-11076
ONLY
$4.13
B
#33-10880
#33-10882
Antenna
Mounting
Hardware
Concrete 1⁄4"
Anchor Kit
#33-10920
#33-10925
Mast Mounts
C
Description
Guy wire clamp up to 11⁄2" mast
Turnbuckle - 7" open, 5" closed
Cable clamps 1⁄2" open 1⁄8" closed
•A variety of mast mounts for finding the perfect location to mount an antenna or satellite dish
•All mount fit up to a 11⁄2" mast •Eave mount adjusts from 46"~68" span
Qty. ONLY
1 $3.73
3
4.13
3
1.55
Order #
33-10880
33-10882
33-10925
33-10920
Description
4" wall mount
8" wall mount
Chimney mount
U-bolt
(1-9)
$5.04
6.35
8.07
1.61
(10-24)
$4.79
5.81
7.67
1.43
(25-49)
$4.55
5.58
7.28
1.31
www.MCMelectronics.com /1-800-543-4330
(50-up)
$4.29
5.40
7.12
1.18
127
7
Turn a two person job into a one
person job and get the job done
faster. You can even pre-install
without using a bolt for final
installation later. The
SnapToggle® anchor is a convenient, reliable, accurate,
easy-to-use anchor, and the strongest toggle bolt in the
smallest hole.
AUDIO/VIDEO
Audio/Video
Distribution
Section
7
Single
Dual
Single
Dual
with ground with ground
Available
in White
7
•Gives a finishing touch and protection to
through-wall cable installations •Available in single,
dual, and ground-wire knock-out configurations
•100 per package
Description
Single, white
Dual, white
Single, black
Dual, black
Single with
ground, white
Dual with
ground, white
Single with
ground, black
Dual with
ground, black
(1-9)
$3.12
3.12
3.12
3.12
3.12
(10-24)
$2.90
2.90
2.90
2.90
2.90
(25-49)
$2.79
2.79
2.79
2.79
2.79
3.73
3.38
3.25
3.12
2.90
2.79
3.73
3.38
3.25
•Flexible black boot slides over
cable and connection to protect it
from outdoor elements •UV resistant
•2" length •100 per package
MSRP
$19.99
Order #
33-040
Order #
33-10935
MSRP
$4.99
(1-9)
$1.61
(10-24) (25-49) (50-up)
$1.43 $1.31 $1.18
Copper Grounding Straps
Wraps around and tightens to pipe, conduit or other
electrode to connect grounding wire.
Order # Length
33-10815
6"
33-10820 12"
(1-9)
$1.61
1.61
•Used to ground outdoor antenna and satellite sytems
•Use with proper grounding wire and clamps for a
complete ground •High-strength steel with copper top
layer •11⁄32" thickness
Order # 33-10810
(1-9)
$3.12
(1-9) (10-24) (25-49) (50-up)
$7.06 $6.78 $6.50 $6.31
Coax Seal
•Hand-moldable plastic
seal is perfect for sealing
outdoor connections and
cable splices •1⁄2'' width
•60'' length
MSRP
$4.99
(1-9)
$1.99
Order # Color 21-3684 Natural 21-3686 Black 21-3688 Natural 21-3690 Black (10-24)
$2.90
(25-49)
$2.79
Description
Security tool
Security sleeve
•Make any cable run look neat
and secured in place by
attaching coax or telecom
cabling to walls and trim with
high-impact plastic cable clips
•Each clip includes a plated
steel nail •100 clips
per package
Order #
33-10850
33-10852
33-10854
33-10856
Description (1-9) (10-24) (25-49) (50-up)
Single, white $2.11 $1.91 $1.76 $1.59
Dual, white
2.62
2.39
2.20 1.98
Single, black 2.11
1.91
1.76 1.59
Dual, black
2.62
2.39
2.20 1.98
Single
Nylon Cable Clamps
Standard screw mount
clamp holds wire up to
⁄2" diameter. Natural color. 50 per bag.
Order #
21-3668
21-3672
21-3676
21-3680
128
Base
Dimensions Price Per Bag
(mm) (1-4) (5-9) (10-up)
21 x 21 $11.99 $9.85 $8.34
21 x 21 11.99 9.85
8.34
28 x 28 17.49 14.97 13.81
28 x 28 17.49 14.97 13.81
ONLY
$7.36
0.60
1
I.D. Width (1-4 bags) ( 5-9 bags) (10 bags-up)
1
⁄8" 3⁄8" $3.12 $2.82 $2.69
1
⁄4" 13⁄32" 2.62 2.12 1.81
3
1
⁄8" ⁄2" 3.12 2.93 2.79
1
1
⁄2" ⁄2" 3.32 3.10 2.87
Order # Description
33-7705 Single
33-7710 Dual
(1-9)
$0.80
2.01
(50-up)
$1.78
Dual
Order #
33-10860
33-10862
33-10864
33-10866
Flex Cable Clips
•Remarkably strong flexible clips
grab cables without damaging them
•Integrated Philips hex-head screws
make installation quick and easy
•100 clips per package
Description (1-9) (10-24) (25-49) (50-up)
Single, white $3.12 $2.90 $2.79 $2.70
Dual, white
3.12
2.90
2.79 2.70
Single, black
3.12
2.90
2.79 2.70
Dual, black
3.12
2.90
2.79 2.70
www.MCMelectronics.com /1-800-543-4330
(10-99)
-
$1.99
(100-up)
$1.91
Copper Split Bolts
•For copper wire grounding
connections and splices •Available for
4, 6, and 8 gauge solid copper wire
Order #
33-10825
33-10830
33-10835
Wire Size
4 AWG
6 AWG
8 AWG
(1-9) (10-24) (25-49) (50-up)
$1.10 $0.95 $0.88 $0.79
1.10 0.95
0.88 0.79
1.10 0.95
0.88 0.79
(50-up)
$2.70
Cable Clips
(10-24) (25-49) (50-up)
$1.89
$1.74
$1.57
•Precision machined,
high-quality security
tool for connecting
and disconnecting
cables protected by a
security sleeve •Long
shaft fits all types
of sleeves
(10-49)
$1.88
High frequency ground blocks have extended frequency
capacity to 2.4GHz making them perfect for satellite
and digital applications. Nickel plated finish to resist
effects of the weather.
Ground Clamps
•Used to properly ground
antennas and satellite
dishes to ground rods or
other electrode points
•Available to fit 5⁄8'' and
3
⁄8'' ground rods
Self Adhesive
Cable Tie Mounts
CATV Security Tool
Order #
33-0025
33-0030
(5-9)
$1.97
High Frequency
Ground Blocks
(10-24) (25-49) (50-up)
$1.43 $1.31 $1.18
1.43
1.31
1.18
Nylon tie mount base accepts
standard cable ties up to 3⁄16" wide.
Self adhesive backing attaches to any smooth surface.
100 per bag. Available in black or natural color.
Order #
33-10945
(1-4)
$2.11
Flat Coax Jumper
4" Grounding Rod
Weather Boot
Order #
33-10950
•Weather resistant, molded plastic construction
•Supplied with rubber boot
•Thin, flexible coax coupler allows you to
run cables through closed windows or other narrow
gaps •Peel-and-stick adhesive keeps jumper in place
•Conforms to any angle •8'' length
Feed-Through Cable Bushings
Order #
33-10870
33-10871
33-10872
33-10873
33-10874
33-10875
33-10876
33-10877
Outdoor Antenna Balun
Order #
33-10840
33-10845
Size
3
⁄8''
5
⁄8''
(1-9)
$1.61
5.75
(10-24)
$1.43
2.44
(25-49) (50-up)
$1.31 $1.18
2.22
2.11
Pipe Clamp
Used to properly ground to copper
water pipes.
Order # 33-10805
(1-9)
$2.01
(10-24)
$1.74
(25-49)
$1.69
(50-up)
$1.58
Drop Enclosures
These drop enclosures
will house and protect
components from the
elements that corrode and
A
shorten their lives. Drop
boxes produce a professional
appearance for cable TV
and satellite installations.
The Omni II box offers
simplicity of installation
B
and professional appearance
along with a generous interior
and the ability to seal the box for drop security.
The Residential Control Box is designed to offer
visual evidence of tampering and provides for easy
maintenance. All boxes are UV resistant and come
in a neutral gray color.
Fig. Order #
A
33-6945
B
33-6950
Description (H) x (W) x (D)
ONLY
Omni II box 5.75 x 5.0 x 1.25 $3.02
Residential 8.75 x 6.25 x 2.75 6.35
Control box
Follow us on:
&
AUDIO/VIDEO
Audio/Video
Distribution
In-Line
Amplifier
DC line powered amplifier for CATV or antenna
applications. Bandwidth is 5~950MHz. Gain is 10dB.
Use with #33-915 power supply.
Order #
33-2690
(1-9)
$12.49
Section
7
(10-up)
$11.62
In-Line Surge
Protector
Protect your cable
modem, tuner,
convertor, decoder,
and satellite receiver
from power surges
and spikes caused by lightning strikes. Plugs directly
into coax line. Specifications: •Frequency range:
5~2,400MHz •Insertion loss: 1.5dB max •Max surge
current: 5000A
Order #
33-10400
ONLY
$7.06
This powerful UHF/VHF antenna signal amplifier is
designed to overcome signal loss related to long cable
runs, splitters, and junctions. While an amplifier will
not create a signal, it will increase its power and
minimize disruptions. Kit includes •Mast mount
amplifier •110VAC power inserter •6' coaxial cable
Frequency range: •40~862MHz •18db gain
•Mfr. #PA18.
Order #
30-2091
Economical Antenna Rotator
Our economical antenna rotator helps improve TV and
FM reception. Two piece connects via three wire rotator
cable. Adjustable clamp accommodates mast up to 11⁄2".
Order #
30-1100
ONLY
$60.99
7
#33-917
#33-910
Outdoor Mast
Mounted Amplifier
ONLY
$50.49
Antenna Rotator
•Heavy-duty motor
handles large antennas
•Extra strong machine cut
gears won’t bind •Brake
pads hold firm •Tested to 70
mph winds •Requires three–
wire rotator wire (#24-3080)
#33-915
In-Line Amplifiers
Specifications: •Bandwidth:
5~950MHz •Gain: 11dB
•Maximum input: 20dB
•Maximum output: 31dB •Noise
figure: 4dB •Power requirements:
15VDC •Dimensions: 21⁄2" (L) x 5⁄8" (dia) #33-910 DC
Passive: For satellite 70MHz in-line amplification
when power dividers, low gain LNAs and down
convertors require additional gain. #33-917 NonPassive: For MATV/CATV applications when antenna
preamplification and line amplification is required.
#33-915 Power Supply: Provides power supply
(15VDC) and diplexer for #33-917 and 33-910.
Order #
33-917
33-910
33-915
Type Non-Passive Amp
DC Passive Amp
Power Supply
(1-9)
$13.99
7.36
14.99
(10-up)
$11.88
6.92
13.42
Push-On Balun
(5-9)
$0.46
(10-up)
$0.43
Tapcon® Self-Tapping Concrete Anchors
•Designed for use with high powered drill and hammer
drivers •Climaseal™ coated for excellent corrosion
protection •Works on all masonry materials, excellent
for exterior walls •Self tapping design cuts their own
threads •Fully removable •1⁄4" diameter •100 per box
Order #
28-8851
Length
1.25"
(1-3 boxes)
$27.99
UHF/VHF Antenna
Mast-Mount Combiner
•All-weather antenna combiner merges the signals from
a UHF antenna with a VHF antenna on the same down
lead •Ideal for FM reception and markets with high
band VHF HDTV channels •Threaded “F” connectors
•Mast-mount weatherproof housing •Adjustable mast
clamp •75ohm output
Order #
30-2113
ONLY
$18.99
ONLY
$80.99
Rotator Cable
Three conductor cable
for use with many
popular antenna rotators. Outer jacket 0.162" black
PVC with 0.020" wall. Three 20AWG conductors color
coded black, white and red.
Order #
24-3080
24-3085
24-3090
Length 100'
500'
1000'
TITAN 2TM Mast Mounted
Preamplifiers
•Quick connect for “F” fittings with
impedance matching transformer
•Minimum five
Order #
33-010
Order #
30-1020
Closed
(4 boxes-up)
$25.70
Mfr. #
7777
7778
VHF Gain
23dB
16dB
(2-4)
$23.02
106.00
190.00
(5-up)
$21.43
98.00
175.00
TM
The Titan range of mast
mounted amplifiers has
been completely
re-engineered and
updated. These
amplifiers
represent the
ultimate in
preamplifier performance. They are designed for
use as an ultra low noise, ultra high gain preamplifier
for deepest fringe applications and MATV headend
applications. Their very high signal handling also
makes them suitable for use as a mast mounted, ultra
low noise distribution amplifier for use in small MATV
systems. Both models feature 75ohm, input and output
connections in line with modern headend engineering
practice. Models 7777 and 7778 cover both VHF and
UHF bands with separate amplification in each band
for maximum signal handling. They may be configured
for either separate or combined VHF and UHF inputs.
They include a switchable FM trap.
Order #
33-8960
33-8965
(ea.)
$30.49
131.00
232.00
UHF Gain
26dB
23dB
ONLY
$70.99
62.99
RG-6/U CL2-Rated Coax Cable
RG-6/U type coax cable. 18AWG solid bare copper
center conductor. Mylar aluminum foil shield plus
40% aluminum braid provides 100% shield. Foam
dielectric and PVC jacket. Outside diameter .270"
nominal. Impedance 75ohm nominal. Perfect cable
for high frequency cable systems, satellite television
and DBS. CL2 rated for in-wall use.
Order #
24-10200
24-10201
Length
500'
1000'
(1-3)
$45.49
111.00
(4-up)
$39.14
97.00
TM
RG-59/U Copper Braid
•22 gauge solid copper-covered steel weld •Foam
dielectric •80% nominal copper braid shield •.240"
(O.D.) nominal •75ohm nominal impedance
Order #
24-10265
24-10266
Length
500'
1000'
(1-3)
$41.49
72.49
www.MCMelectronics.com /1-800-543-4330
(4-8)
$39.14
68.50
(9-up)
$37.08
64.89
129
Section
7
AUDIO/VIDEO
Audio/Video
Distribution
H24 High Definition Receiver
D12 Series Standard Receiver
Slimline Dish and LNBF
7
•Dish kit includes mounting brackets,
arm, mast, and Slimline reflector •Use
dish kit with any of the LNBF options •All LNBF
units receive orbital 99°/101°/103° for all DIRECTV®
standard programming •5-LNBF units additionally
receive 110°/119° for local HD programming in some
areas •SWM options for running single wire from the
dish to SWM compatible multi-switches and splitters
Order #
33-10990
33-10992
33-10994
33-10996
33-10998
Description
Slimline dish kit with mounts
3-LNBF, 4 outputs
3-LNBF, 1 output (SWM)
5-LNBF, 4 outputs
5-LNBF, 1 output (SWM)
ONLY
$69.99
39.99
89.99
59.99
99.99
With the DIRECTV® D12 series
receiver, you can access over 250
digital-quality channels, plus access
interactive capabilities and a customizable on-screen
program guide. Explore and personalize all your
viewing options quickly and easily with the included
remote control. Features: •Interactive features include
mix channels, DIRECTV® Active, and MiniGuide
•Parental controls to set rating restrictions and
spending limits •Programming options like CHOICE,
DIRECTV® Spanish, XM satellite radio and pay per
view movie and event channels Includes: •Access card
•Remote controls and batteries •A/V and S-video cables
•Phone and power cords •User guide •This equipment
is for use only with DIRECTV® subscription
television service and is subject to DIRECTV's®
terms and conditions
Order #
33-7701
#33-7706
#33-7706
The HR-PRO series DVR is the
high-end DIRECTV® solution for
professionally installed home theater and commercial
systems. Features: •Rack mountable •View
programming featuring 1080i high definition video
with Doby Digital 5.1 audio •Record up to 400 hours
of programming (100 hours of HD) •Plan ahead with
14 Advanced Program Guide® •Exclusive DLI optical
HDMI link allows for a remote television to receive
high-definition content through fiber optic cable up to
1000' away •Outputs include: HDMI A/V, optical
HDMI A/V, S-video, dual component video, composite
A/V, optical digital audio (toslink), and coaxial digital
audio •Inputs include: Dual satellite, USB, RS-232C,
IR, dual ethernet, phone jack, SATA, and 120VAC
Includes: •6' HDMI cable •6' component video cable •6'
composite A/V cable •RF remote •Power cable •Rack
mounting hardware •DIRECTV® service and
installation not included
Order #
33-10570
33-7706
Description
HR21 PRO receiver
Dual ATSC add-on tuner
Add DIRECTV® and DVR Service
and you get the best choice and
widest selection of high definition
programming. Features: •Standard-definition (SD) and
high-definition (HD) enabled •Simultaneous SD and
HD output •Record up to 200 hours of SD, or up to
50 hours of HD programming •Two satellite tuners for
access to SD and HD DIRECTV programming •14-day
Advanced Program Guide® •Pause and rewind live TV
for up to 90 minutes •Series Link® feature •One touch
record, auto record, manual record, and bookmarks
•Search and record •Interactive TV enabled •This
equipment is for use only with DIRECTV® subscription
television service and is subject to DIRECTV's® terms
and conditions
Order #
33-7704
33-7706
ONLY
$129.00
Single Wire
Multi-Switch
High-Definition HR24 Series DVR
High-Definition
HR-PRO Series DVR
Order #
33-7703
ONLY
$94.99
#33-7704
#33-10570
With the DIRECTV® H series receiver,
you can access over 265 digital-quality
audio and video channels from
DIRECTV® in both high-definition and standard
definition Features: •Versatile HDTV connection
options include HDMI digital audio/video and
component video, as well as standard composite
video and RCA audio •1080i picture output resolution
formats •Dolby® Digital 5.1 surround sound capable
•MPEG-4 AVC capable Includes: •Access card •B-band
convertor •Remote control and batteries •Component,
S-video, and standard A/V cables •Phone and power
cords •User guide •This equipment is for use only with
DIRECTV® subscription television service and is
subject to DIRECTV’s® terms and conditions
Description
HR24 high-def receiver
Dual ATSC add-on tuner
ONLY
$239.00
82.49
•Combine up to
six LNB inputs
(flex ports 72.5°/95°,
5-LNB 99°/101°,
103°/110°/119°) for a
simpler, single wire installation into the home
•Two SWM outputs can be split with SWM compliant
high-frequency splitters for up to eight receivers or four
DVRs •DIRECTV® compatible DVRs receive both
needed signals from a single connection •Three legacy
outlets for older equipment •Off-air antenna diplexer
included •Power inserter required, sold separately
Order #
33-11000
33-11005
Description
Single wire multi-switch
28V power inserter
SWM Compatible
Splitters
•High-frequency RF splitters designed for use with
splitting SWM satellite signals •One port DC pass
•DIRECTV® SWM approved
Order #
33-11010
33-11012
33-11014
ONLY
$649.00
82.49
ONLY
$179.00
19.99
Description
2-way
4-way
8-way
ONLY
$5.99
8.99
15.99
R Series DVR
•Piggy-back tuner designed for seamless use with
DirecTV® receivers HR21 and HR21PR •Receive local
digital broadcasts from off-air antenna and integrate
them into the program guide •Simple one-time set-up
•Dual tuner enables off-air HD-DVR capabilities with
existing HR21 or HR21PRO •Simple USB connection
to main satellite receiver •Dimensions: 15.125" (W) x
12.25" (D) x 1.18" (H)
The DIRECTV Plus™ DVR receiver
lets you record up to 100 hours of
programs, and pause or control live TV.
With the R22 receiver you can automatically record an
entire season of your favorite shows, find and record
programs by title, actor, or director, listen to theaterquality Dolby® Digital sound, and schedule recording
up to 14 days in advance. Includes: •Access card
•Remote controls and batteries •A/V and S-video
cables •Phone and power cords •User guide •This
equipment is for use only with DIRECTV®
subscription television service and is subject
to DIRECTV's® terms and conditions
Order #
33-7706
Order #
33-7702
Dual ATSC Tuner for
DIRECTV Receivers
130
ONLY
$82.49
www.MCMelectronics.com /1-800-543-4330
ONLY
$129.00
SWM Expanders
•Connect two or four
SWM8 switches for up to 16
or 32 channels out •Mounts as one
unit, no additional chassis required •Requires 24-volt
power supply (two for 33-11020), sold separately
Order #
33-11015
33-11020
33-11021
Description
Combines two SWM8
Combines four SWM8
24V power supply
Follow us on:
&
ONLY
$129.00
169.00
49.99
AUDIO/VIDEO
Audio/Video
Distribution
Section
7
6 x 8 Multi-Switch
•Six satellite inputs: four inputs from 101°/110°/119°
and 99°/103°; two flex port inputs from 72.5° and 95°
for international and local programming •Passive unit
powered by connected satellite receivers •Wide band
frequencies: 250~750MHz, 950~1450MHz, and
1650~2150MHz
Order #
33-11007
ONLY
$69.99
Four satellite IF and one terrestrial TV input to 12
outputs to satellite receivers. Built–in satellite IF
amplifier compensates for splitter loss. LNB selection
by 14/18VDC and 22KHz tone provided by equipped
receivers. Built–in power supply provides power for
operation, amplification and operation of the LNBs.
Order #
33-8690
(1-9)
$88.99
(10-up)
$86.38
DBS LNB for use with digital satellite
system dishes with rectangular shaped
tubes. Designed to work with “D”
shaped tubes as well. Perfect low cost
replacement for damaged LNBs.
•Combines off-air signals with a
satellite drop •Power passive one
port •40~860MHz/ 950~2250MHz
•Includes grounding screw
MSRP
$4.99
Order #
MSRP
33-10970 $5.99
“C” and “Ku” band LNBs for use with “C”
band antennas. Professional feedhorns and
commercial grade LNBs assure high
performance with low noise. Input
frequency: 11.7GHz~12.2GHz Output
frequency: 950MHz~2000GHz.
ONLY
$32.99
40.49
Compass
Economical compass for easily
identifying satellite positions.
Small size fits in the palm
of your hand. Top closes
to protect surface from
scratches. Specifications:
•Directional accuracy: ±5° •Direction indication: 2°/
scale •Dimensions: 72mm x 55mm x 30mm
Order #
33-2050
Diplexer
(1-9)
$1.50
(10-24)
$1.43
(25-49) (50-up)
$1.31
$1.18
ONLY
$3.12
(1-9)
$3.02
(25-49)
$2.79
(50-up)
$2.70
Features: Die-cast housing, low noise: 4dB, high gain:
20dB, passes DC through for powering LNBs, sloped
gain for long cable runs, voltage supplied by the
satellite receiver Specifications: •Noise figure: 4dB
•Gain: 950MHz: 15dB, 1450MHz: 18dB, 1750MHz:
20dB, 2150MHz: 21dB •Maximum output: 30dBmV
(12 channels) •DC voltage: 15~18VDC (negative
ground) •Connectors: “F” type
(1-9)
$11.99
ONLY
$62.99
147.00
This hand held CATV/satellite
meter has been designed for the
technician to make quick and
accurate signal strength
measurements for both CATV
and satellite. This powerful,
simple to use tool measures
frequencies from
25MHz~1550MHz. •Measures
satellite from DIRECTV®, DishNetwork, CATV and broadcast
signal strength •Two rows of ten
easy-to-read indicator lights •Hand
held design, great for use with
HDTV •Includes 22KHz tone
generator for use with dual satellite
systems •Requires 9V battery (included) •Mfr. #M200
Order #
33-9695
(1-9)
$393.00
(10-up)
$10.83
(10-up)
$375.00
Acutrac®22 Digital
Satellite Signal
Level Meter
The Acutrac®22 allows an installer to easily align
a multi–feed system by displaying LNB A and LNB
B signal strength measurement levels simultaneously.
The Acutrac®22 features include: LCD display,
selectable audio on-off tone, receiver voltage output,
individual LNB current consumption, 22KHz tone
and coax cable test. Acutrac®22 Pro also includes:
Rechargable battery pack, leather case and AC/DC
chargers. Mfr. #AcutracPro.
Satellite Finder Meter
•Position and aim satellite
dishes with ease •Connects
between the LNB and
satellite receiver or 13~18V
power supply •Frequency
range: 950MHz~2.4GHz •Gain: 11dB
•Operating range: 52~60dB LNB gain
Order #
33-10940
Mfr. #
1004IFD
1007IFD
RF/Satellite Meter
(10-24)
$2.90
In-Line
950~2150MHz
Amplifier
Order #
33-2720
Satellite Signal Level Meters
The 1004IFD and 1007IFD are intended to aid in the
alignment of a satellite dish. They include satellite IF
(950~2150MHz) amplification and a broadband
detector. The detector drives a meter and a variable
frequency audio tone. The dish is then aligned for
maximum meter deflection or highest pitch tone. A gain
control allows a wide range of input signal levels. The
units are connected to the LNB via a short coaxial
cable. The 1004IFD output must be connected to the
satellite receiver in order to supply power. The units
operate from 11~24VDC on the coaxial cable.
Connection to the receiver is optional with the
1007IFD, but extends battery life between charges. All
models allow measurement of voltage on the coaxial
cable. The 1007IFD will also measure LNB current.
The 1007IFD includes an internal rechargeable battery
pack, carrying strap and a wall plug recharging unit.
The internal battery pack allows a dish to be aligned
before it is connected to the satellite receiver. The
battery pack is switchable between 13 and 18V output,
allowing either polarization to be selected when used
with a voltage switched LNB. In US DBS applications,
LHCP is selected when the LNB voltage is
nominally 17V.
Order #
33-9295
33-9300
•In-line amplifier for
satellite cable runs greater
than 100' •20dB max slope
gain •For 900~2150MHz
ONLY
$22.99
Noise figure
0.6
0.5
ONLY
$20.49
In-Line Amplifier
Precision Ku Band LNBs
Order #
33-4705
33-4710
Order #
33-9665
Order #
33-10975
High Performance Dual LNB
Order #
33-7435
The BMS-58 allows up to eight satellite
television receiver connections to a single multi–satellite
dish and provides an additional off air antenna/cable
input to integrate all television options. With the Terk
BMS-58 multi–switch you can install a home theater
multiplex in no time by connecting up to eight receivers
with ease. There is no need to remove integrated multi–
switches already embedded in the satellite dish. Simply
connect the two SatA and SatB cables to the BMS-58
and run to the receivers. The BMS-58 has an ultra–low
noise built–in amplifier to eliminate signal loss and
deliver the best possible reception to every TV. The
TERK BMS-58 is designed to be waterproof making it
rugged, durable and easy to install. Mfr. #BMS-58.
Limited quantities.
ONLY
$10.99
Order #
33-7395
www.MCMelectronics.com /1-800-543-4330
ONLY
$139.00
131
7
5 x 12 Multi-Satellite Multi-Switch
5 x 8 Integrated Multi–Switch
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising