Ashly MX-508 Specifications

Ashly MX-508 Specifications
MX-508
Stereo Microphone/Line Mixer
Operating Manual
Ashly Audio Inc.
847 Holt Road, Webster, NY 14580-9103
Toll Free (800) 828-6308, Telephone (585) 872-0010, FAX (585) 872-0739
www.ashly.com
All Trademarks referred to herein, are the property of their respective owners. R-042707
All Rights Reserved
Page - 2
Operator Manual – MX-508 Mixer
This page intentionally left blank
Copyright© 2006 – Ashly Audio Inc.
Operator Manual – MX-508 Mixer
Page - 3
Important Safety Instructions
Consignes de sécurité à lire attentivement
Safety Instructions – 3
Introduction - 4
MX-508 Mixer – 5
Connectors & Cables – 5
Physical Description - 6
Installation – 7
Typical Applications - 8
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons. The exclamation point within an equilateral
triangle is intended to alert the user to the presence of important operating and
maintenance instructions in the literature accompanying the device.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury
from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
Le symbole de la flèche dans un triangle équilateral symbolisant la foudre est
prévu pour sensibiliser l’utilisateur à la présence de tension de voltage non isolée
à l’intérieur de l’appareil. Elle pourrait constituer un danger de risque de
décharge électrique pour les utilisateurs. Le point d’exclamation dans le triangle
équilatérale alerte l’utilisateur de la présence de consignes qu’il doit d’abord
consulter avant d’utiliser l’appareil.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Lisez ces instructions.
Conservez ces instructions.
Observez les avertissements.
Suivez ces instructions.
Pour réduire le risque de feu ou la décharge électrique,
ne pas exposer cet appareil pour pleuvoir ou l'humidité.
Ne pas utiliser l’appareil près de l’eau.
Le nettoyer à l’aide d’un tissus sec.
Ne pas bloquer les ouvertures de ventilation, installer
selon les consignes du fabricant.
Eloigner des sources de chaleur tel: radiateurs,
fourneaux ou autres appareils qui produisent de la
chaleur.
Ne pas modifier ou amputer le système de la mise à
terre. Une prise avec mise à terre comprend deux lames
dont une plus large ainsi qu’une mise à terre: ne pas la
couper ou la modifier. Si la prise murale n’accepte pas
la fiche, consulter un électricien pour qu’il remplace la
prise désuète.
Protéger le cordon de secteur contre tous bris ou
pincement qui pourraient l’endommager, soit à la fiche
murale ou à l’appareil.
N’employer que les accessoires recommandés par le
fabricant.
N’utiliser qu’avec les systèmes de fixation,chariots,
trépied ou autres, approuvés par le fabricant ou vendus
avec l’appareil.
Débrancher l’appareil lors des orages électriques ou si
inutilisé pendant une longue période de temps.
Un entretient effectué par un centre de service accrédité
est exigé si l’appareil a été endommagé de quelque
façon: si il a été exposé à la pluie,, l’humidité ou s’il ne
fonctionne pas normalement ou qu’il a été échappé.
All Rights Reserved
Factory Configs - 8
Troubleshooting - 9
Dimensions - 9
Specifications - 10
Warranty - 11
This manual uses a
Perpetual Table Of
Contents. Each page
has a copy of the
manual’s contents in a
gray box just like this
one. The section you are
in will always be bold
with the other sections
“grayed out.” The feature
allows you to jump
directly to another
section without having to
return to a Table Of
Contents page.
Page - 4
Operator Manual – MX-508 Mixer
Safety Instructions – 3
Introduction - 4
MX-508 Mixer – 5
Connectors & Cables – 5
Physical Description - 6
Installation – 7
Typical Applications - 8
Factory Configs - 8
Troubleshooting - 9
Dimensions - 9
Specifications - 10
Warranty - 11
Introduction
Congratulations on your purchase of an Ashly MX-508 stereo mixer. In one compact rackmount package we have combined features, reliability, and sonic performance previously
found only in larger and more expensive mixing consoles. Features of this unit include:
Optional isolation transformers on all inputs
Switchable +48V phantom power
Front panel mic/line switching
Three-band equalization
Concentric level and pan control on each channel
Concentric pair of auxiliary sends on each channel
Ultra low-noise summing amplifiers
Two 10-segment LED arrays
Standard line level outputs on 1/4" connectors
Tape outputs on RCA connectors
Transformer isolated 600 ohm outputs on XLR connectors
Professional quality 16mm metal shaft potentiometers on all controls
About Ashly
Ashly Audio was founded in 1974 by a group of recording engineers, sound professionals,
and electronics designers. The first products were custom consoles for friends and
associates, but business quickly grew. The philosophy established from the very beginning
holds true today: to offer only the highest quality audio tools at an affordable cost to the
professional user – ensuring reliability and long life. More than thirty years later, Ashly
remains committed to these principles.
Copyright© 2006 – Ashly Audio Inc.
Operator Manual – MX-508 Mixer
Page - 5
Safety Instructions – 3
MX-508 Mixer
Introduction - 4
The MX-508 is a versatile rack-mountable mixer capable of supporting the following
applications:
Small Sound Reinforcement
Meeting/Board Room
Location Recording
Sub-mixing in a larger system
These applications are discussed in detail on Page 8.
MX-508 Mixer – 5
Connectors & Cables – 5
Grounding
Physical Description - 6
Installation – 7
Typical Applications - 8
Factory Configs - 8
Troubleshooting - 9
Connectors & Cables
Dimensions - 9
Your MX-508 is provided with three different connector types:
1. 1/4 inch stereo phone jacks (TRS)
2. Three pin XLR type connectors
3. RCA Connectors
When possible, balanced connections are recommend between all components in your
system, as this eliminates ground-loop induced hum and noise.
MX-508 Connector Polarities
Unbalanced Connections and Grounding
If you must use unbalanced connectors, the negative lead of the connector should be tied to
the ground lead. Using unbalanced connections could result in chassis ground-loop noise.
Altering the signal/chassis ground relationship in equipment connected to your unit may
eliminate the noise.
All Rights Reserved
Specifications - 10
Warranty - 11
Page - 6
Operator Manual – MX-508 Mixer
Safety Instructions – 3
Introduction - 4
MX-508 Mixer – 5
Connectors & Cables – 5
Physical Description
The MX-508 is 4RU, and weighs 19 pounds.
MX-508 Front Panel
Physical Description - 6
Front Panel
Rear Panel
Installation – 7
Typical Applications - 8
Factory Configs - 8
Troubleshooting - 9
Dimensions - 9
Specifications - 10
Warranty - 11
1.
2.
3.
4.
5.
6.
7.
8.
9.
Input Level (Gain) - Sets the operating level of
the Mic preamp and Line Input. It is desirable to
set the Gain control as high as possible while
still leaving enough headroom to prevent
distortion.
Mic-Line Switch - Switches between the XLR
microphone input or the 1/4" line input jack as
the signal source. It can also serve as a
"channel mute" when switched to an unused
input.
Channel Clip Indicator - This peak indicator
monitors all level critical points in the input
channel and illuminates if any of them reach
levels within 3 dB of clipping.
Equalization - EQ consists of a high shelf
control at 15KHz (middle of shelf), a sweepable
mid control, and a 70Hz low shelf control. The
mid control is sweepable from 140Hz to 8KHz
with a bandwidth of approximately 1 octave.
Aux Sends - This pair of level controls adjust
the feed to monitors or effects units. Aux 1 is
factory preset to pre-fader, pre-EQ, while Aux 2
is post-fader, post-EQ. Both Aux sends can be
internally switched to pre or post fader/EQ.
Level and Pan - This concentric pair of
controls adjusts the level and stereo position of
the channel in the mix.
Aux Master Sends - These controls adjust the
overall gain of the output stages for the Aux 1
and Aux 2 outputs.
Aux Master Returns With Pan - These
controls adjust the returning signal from effects
units or auxiliary inputs to the Left and Right
outputs. Return 1 is stereo and return 2 is
mono. If only the right connection to return 1 is
used, this return will function as mono with pan.
Tape/CD Input and Send - Adjusts the
Tape/CD input to the Main Stereo outputs. The
outer concentric control labeled "To Aux 1"
sums the stereo Tape/CD signal to mono and
applies it to the Aux 1 Master group (pre-fader)
for use with monitors or effects.
10. Output Meters - A pair of peak reading 10
segment LED meters are used to indicate
output level. Green < 0 VU, Yellow >0 VU, and
Red = clipping. This meter pair is switchable
between the Main Left and Right, or the Aux 1
and 2 outputs. The red clip LED's will illuminate
if the summing amplifiers are clipping even if
the main output controls are off. Note: The
output meters are accurately calibrated to the
transformerless output levels, but not
necessarily the transformer-balanced outputs.
11. Main Output Level - These controls determine
the level of both transformer balanced and
transformerless output stages for the Main Left
and Right outputs.
12. Main Output Mutes - Switches off both the
transformer-balanced outputs as well as the
1/4" stereo outputs, indicated by the red LED
near the switch. The headphone and metering
functions continue uninterrupted.
13. Phantom Power Switch - This front panel
switch enables the +48 Volt phantom power for
condenser microphones. One switch controls
all the inputs. If you have both condenser and
dynamic microphones, the phantom power will
not affect the operation of the dynamic mics.
14. Mono Output Level - This control adjusts the
level of the summed mono output. It is
completely independent of the Main Left and
Right masters.
15. Headphones Level - This control adjusts the
level of the designated output signal (Mains or
Aux) to the headphone jack.
16. Meter/Phones Select - This switch selects
either the Main Left/Right outputs or the Aux
1/Aux 2 outputs to the LED meters and the
headphone jack.
17. Headphone Output - This front panel 1/4" TRS
connector feeds a standard set of stereo
headphones. A selector switch that also
controls the level meter allows monitoring the
main or Aux outputs.
Copyright© 2006 – Ashly Audio Inc.
Operator Manual – MX-508 Mixer
Page - 7
Safety Instructions – 3
MX-508 Rear Panel
Introduction - 4
MX-508 Mixer – 5
Connectors & Cables – 5
Physical Description - 6
Front Panel
Rear Panel
Installation – 7
Typical Applications - 8
Factory Configs - 8
1.
2.
3.
4.
Microphone Input - The microphone input is
an active balanced type with a nominal
impedance of 1200 . Its noise performance is
best with a 200 microphone. A plug-in
transformer option is available. The Mic input
connector is a standard 3-pin XLR female
Input Pad - The Pad is a 20dB attenuation
switch on the rear panel for use with the mic
input when the input is being overdriven with
the Gain control at its minimum setting.
Line Input - A standard 1/4" TRS active
balanced connection, with a balanced input
impedance of 20K.
Channel Send & Return Patch - The channel
patch point allows an effect (EQ, compressor/
limiter, etc.) or direct out recording device to be
used on an individual channel. The MX-508 has
both single jack insert capabilities as well as
separate send and return jacks.
To use the separate send/return jacks, connect
the send jack to the input of the device to be
inserted, and use the return jack its output.
Unbalanced (tip-sleeve) mono plugs are
required for this configuration.
To use the single jack insert, use a balanced
(tip-ring-sleeve) stereo plug in the send jack
only, where the send output signal is on the tip,
and the return signal is applied to the ring.
To use the send jack as a Direct Line Output (pre
EQ), you must use a special cable with tip and
ring connected at the MX-508 Send and a tipsleeve mono plug at the other end. Connecting
tip and ring at the mixer is necessary for
uninterrupted signal within the mixer.
5.
6.
7.
8.
9.
Aux Send Outputs - The Aux Outputs are
used to drive monitors, or any function which
requires isolated level control from the main
outputs. They are pseudo-balanced 1/4" tipring-sleeve.
Aux Return Inputs - The return inputs are 1/4"
unbalanced. Return 1 is stereo, while Return 2
is mono. To use return 1 as mono, connect only
to the Right return 1 input.
Tape/CD Input - Tape Output - The stereo
inputs on RCA connectors have a nominal
operating level of -10dBu. The tape outputs are
-10dBu "pre-master", so they are not affected
by the settings of the Main output controls.
Transformer Balanced Outputs - The
transformer outputs use male XLR connectors
and provide isolation for 600 lines and are
controlled by the L & R Master levels, with a
nominal operating level of +4dBu.
Note: The transformer-balanced outputs are
designed to drive up to +24dBu into 600 loads. With output transformers, the level
increases as the impedance of the terminating
load exceeds 600 . Unlike a direct-coupled
output, transformers are affected by termination
impedance. Expect a slight increase in output
level when driving high impedance inputs with
these outputs. The output meters will remain
accurately calibrated to the levels present on
the transformerless outputs, regardless of the
load on the transformer outputs.
Main Outputs – The Main Outputs are also
controlled by the L & R master. They are 1/4"
balanced TRS jacks with a nominal operating
level of +4dBu into any load
Installation
Always switch the unit off before making substantial changes to the settings or connectors. Use
four screws and washers when rack mounting. This unit has specific electrical and signal
requirements, please take special care to double check all connections and settings and refer to
the specifications section of this manual. The unit should be connected to a standard 3-wire
grounded electrical outlet supplying 100-240 Volts, 50-60 Hz. To reduce the risk of ground
loop hum, connect all audio equipment to the same electrical power source. Removal of the
ground pin is both unlawful and dangerous, as a potential shock hazard could result. Overall
power consumption is less than 30 watts.
All Rights Reserved
Troubleshooting - 9
Dimensions - 9
Specifications - 10
Warranty - 11
Page - 8
Operator Manual – MX-508 Mixer
Safety Instructions – 3
Introduction - 4
Typical Applications
MX-508 Mixer – 5
The following information will help you make the most of your new mixer:
Connectors & Cables – 5
Small Sound Reinforcement System
Physical Description - 6
Typical Applications - 8
Small Reinforcement
Meeting Room
Location/Broadcast
Submixing
The MX-508 can be used to mix typical sound sources that might be found in a small club,
school theater or similar environment. Six of the input channels are used for microphones
for live vocal or instrumental pickup. The remaining two channels are used for playback
from a stereo tape recorder, such as might be used during intermission, for backup, for
special recorded effects, etc. Power amplifier(s) (or any additional outboard equipment) is
fed from the transformer balanced Output connectors.
Factory Configs - 8
Meeting Room or Church Using Remote Control
Troubleshooting - 9
The MX-508 can be interfaced with an Ashly VCX-88C eight channel remote level
controller, allowing a full-featured mixer to be operated from a distance by a non-technical
person. Once initially set up, the RD-8C desktop remote controller can be located far away
from the main audio equipment rack using a single balanced XLR cable, allowing for
simplified sound system operation using a limited number of knobs, lights, and buttons.
Installation – 7
Dimensions - 9
Specifications - 10
Warranty - 11
Location Recording or Broadcast Mixing
The MX-508 can be used to mix sources typically found in location recording or broadcast
situations (mostly microphones). The Tape Out jacks can feed a portable tape recorder, and
the recorder's line output is brought back to the Tape/CD Input connectors for monitoring.
For live remote broadcast applications the Mono Out connector can feed a suitable TELCO
or Internet interface.
Submixer In Larger Sound System:
The MX-508 can be used to provide a drum mix to the main mixer without tying channels
on the main console. Up to eight mics can be "pre-mixed" in stereo, with all drum-specific
gating, compression, and effects controlled directly by the drummer. Either the main
OUTPUT or the SUB OUT connectors can be used to feed the mixed drum signal to the
main mixer. If there is significant distance between the MX-508 and the "master" mixer,
use the balanced or transformer- balanced Main outputs for long cable runs.
Changing Factory Configurations
The MX-508 has the following user-configurable options:
Changing the Aux Pre/Post Assignment
The MX-508 is shipped from the factory with Aux 1 assigned Pre-Fader/EQ, and Aux 2
Post-Fader/EQ. Each channel's Aux Send can be independently configured for either pre
or post fader/EQ operation. To make this change: Unplug the unit's AC power cord from
the outlet. Locate the 3 pin headers labeled Send 1 and Send 2 near the front of each input
channel circuit board. Remove the shunt bar from the factory installed position indicated
on the circuit board legend and place the shunt on the other position of the 3 pin header.
Installation of Input Transformers
The MX-508 is designed to accept optional plug-in input isolation transformers with a
minimum of tools and no soldering. Instructions for installation are included when you
purchase an Ashly MX-508 ITC Kit.
Copyright© 2006 – Ashly Audio Inc.
Operator Manual – MX-508 Mixer
Page - 9
Safety Instructions – 3
Troubleshooting
Introduction - 4
Situation
Action
MX-508 Mixer – 5
No Sound
Check the AC power. Is the power switch on and the front-panel LED illuminated? Check the
level meters. If they are operating, either the problem is between the mixer and the later
components in the system, or else the Output Mute switches are pressed. If there is no meter
activity, check to see you really have an input signal and that it is on the desired channel, or
check to see that the meter select switch is set to Left/Right. Check that you have the master
gain controls at the desired operating level.
Something is being overdriven in the signal path. If the clip indicators are active, reduce the
channel gain controls and/or press in the pad switch on the rear panel. If the level meters are
constantly in the red, reduce the Master gain and increase the gain of components following
the mixer. There are many gain adjustments in the mixer itself and probably several others in
other system components which makes it possible to overdrive an input section and then
incorrectly try to reduce the gain of the output section. The best way to approach setting
gains is to establish the operating level of input stages first by setting their gain as high as
possible but leaving about 20dB of headroom for loud peaks, then move on to set the master
gain to produce a good meter reading. Proceed to set the gain of equalizers, limiters,
crossovers, and amplifiers following the mixer in the same manner, always working toward
the later stages of the system.
If the noise is in the form of hiss, the problem is usually due to an input stage set up for low
gain and then compensating by increasing the master gain. Check that the Pad switch is not
enabled unnecessarily. Turn up the channel gain controls and reduce the master gain.
This is usually caused by "ground loops" in the system wiring. A complex sound system with
many sources separated by significant distance and using several power outlets has many
opportunities for this problem to occur. If possible, feed everything in the system from one
power source with a common ground. Use balanced input and output connections between
widely separated components.
Connectors & Cables – 5
Distorted Sound
Excessive Noise
Excessive Hum or Noise
Note: Unshielded cables, improperly wired connections, and cable with broken strands are
the most common problems. Make sure you use good quality cable with connectors
soldered firmly on the correct pin. When in doubt, get in touch with your Ashly dealer.
Dimensions
Inches (Millimeters)
All Rights Reserved
Physical Description - 6
Installation – 7
Typical Applications - 8
Factory Configs - 8
Troubleshooting - 9
Dimensions - 9
Specifications - 10
Warranty - 11
Page - 10
Safety Instructions – 3
Introduction - 4
MX-508 Mixer – 5
Connectors & Cables – 5
Physical Description - 6
Installation – 7
Typical Applications - 8
Factory Configs - 8
Troubleshooting - 9
Dimensions - 9
Specifications - 10
Warranty - 11
Operator Manual – MX-508 Mixer
Specifications
SPECIFICATION
DISTORTION
THD at +4 dBu, 20Hz-20KHz
THD at +20dBu, 30Hz-10KHz
IMD (SMPTE) at +20dBu
HUM & NOISE (20Hz-20KHz at max preamp gain)
Equivalent input hum and noise
Residual output noise, all levels at minimum
Master Level and one Ch. Level at nom
Aux 1 or 2 Out, Aux Master and one Ch. Aux at nom .
MAXIMUM VOLTAGE GAIN (±2dB)
Mic Input to Master Output, 600 ohm load
Line Input to Master Output, 600 ohm load
AUX SENDS
Mic Input to Aux Master Output, pre ch. level
Mic Input to Aux Master 2 Output, post ch. level
SUB Input to Master Output
AUX RETURNS 1 or 2 to Master Output
TAPE/CD In to Master Output
FREQUENCY RESPONSE
20Hz-20KHz
50Hz-10KHz
EQUALIZATION
Low
Mid
High
CROSSTALK
Adjacent inputs, 20Hz-20KHz
Mic Input to Master Output, 1KHz
Mic Input to Master Output, 20KHz
VU METERS (Selectable to Main or Aux Outputs)
PEAK INDICATORS
MX-508
<0.05%
<0.05%
<0.05%
<-127dBu
<-100dBu
<-80dBu
<-80dBu
84dB
42dB
76dB
92dB
12dB
30dB
34dB
+0.5/-1.0dB
+0/-0.5dB
±12dB at 70Hz, shelving
±12dB peaking, 140Hz-8KHz
. ±12dB at 15KHz, shelving
<-65dB
<-65dB
<-55dB
0VU = +4dBu
Indicator on Inputs, L & R outputs, lights 3dB below clipping
Maximum total current draw = 80mA.
PHANTOM POWER
Maximum single channel current draw = 14mA.
(+48 VDC applied to all Mic Inputs, switchable on front panel)
Gradual power-up and down to eliminate "pops".
SHIPPING WEIGHT
20 lbs. maximum with 8 input transformer options installed
POWER REQUIREMENTS
100-240 VAC, 50-60 Hz, 30 watts
Unless otherwise stated, specification conditions are: 150 source, Input Level set at "-40", all other controls set at nominal.
Input Specifications
Input
Balanced/
Unbalanced
Mic 1-8
Balanced
Line 1-8
Balanced
Aux Returns
1&2
Sub (L, R, Aux)
Tape/CD
Input Level & Pad
Input level @ -60 (pad out)
Input level @ -20 (pad out)
Input level @ -20 (pad in)
Input level @-24
Input level @+22
Load
Impedance
For use w/
Nominal
1K 50 to
600 mics
10K 600 lines
Sensitivity
-80 dBu
-40 dBu
-20 dBu
-38 dBu
NA
Unbalanced
NA
10K 600 lines
-26 dBu
Unbalanced
Unbalanced
NA
NA
10K 10K 600 lines
600 lines
-8 dBu
-30 dBu
Max Input
before Clip
-42 dBu
0 dBu
+20 dBu
-2 dBu
+24 dBu
+24 dBu Ret 1
+23 dBu Ret 2
+24 dBu
+15 dBu
Connector
Female
XLR
1/4” TRS
1/4” TRS
1/4” TRS
RCA
Output Specifications
Output
Master Out (L, R)
Master Out (L, R)
Mono Out
Aux Out 1,2)
Sub Out (L, R)
Balanced/
Unbalanced
Transformer Balanced
Source
Impedance
200 For use w/
Nominal
600 lines
Output Level
Nominal
+4 dBu
Output Level Max
before Clip
+24 dBu
Male XLR
Servo Balanced
200 10 K lines
+4 dBu
+23 dBu
1/4” TRS
Connector
Quasi-Balanced
200 10 K lines
+4 dBu
+23 dBu
1/4” TRS
Sub Out (AUX 1,2)
Unbalanced
680 10 K lines
+4 dBu
+23 dBu
1/4” TRS
Tape Out (L, R)
Un Balanced
680 10 K lines
+4 dBu
+12 dBu
RCA
Notes: 1. 0 dBu = 0.775 Vrms 2. Quasi-balanced output has balanced output with single ended signal 3. Sensitivity is input signal level which will produce +4 dBu out with all levels maximum
Copyright© 2006 – Ashly Audio Inc.
Operator Manual – MX-508 Mixer
Page - 11
Introduction
Safety
Instructions
-2
–3
Limited Warranty
The PE Series
Introduction
- 4- 3
Warranty service for this unit will be provided by ASHLY AUDIO INC. in accordance with
the following warrant statement.
ASHLY AUDIO INC. warrants to the owner of this product that this product and the
components thereof, will be free from defects in workmanship and materials for a period of
FIVE years from the date of purchase. ASHLY AUDIO INC. (ASHLY AUDIO) will,
without charge, repair or replace, at its option, defective product or component parts upon
prepaid delivery to the factory service department or authorized service center, accompanied
by proof of purchase date in the form of a valid sales receipt. This warranty gives you
specific legal rights, and you may also have other rights which vary from state to state.
EXCLUSIONS: This warranty does not apply in the event of misuse, neglect or as a result of
unauthorized alterations or repairs. This warranty is void if the serial number is altered,
defaced, or removed. ASHLY AUDIO reserves the right to make changes in design or make
additions to or improvements upon this product without any obligation to install the same on
products previously manufactured.
Any implied warranties which may arise under the operation of State law shall be effective
only for FIVE years from the date of purchase of the product. Ashly Audio shall be liable only
to correct defects in the product itself, and not for any damage or injury which may result from
or be incidental to or a consequence of such defect. Some states do not allow either limitations
on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you.
Obtaining Warranty Service in the United States
For warranty service in the United States, please follow this procedure:
Return the product to Ashly, freight prepaid, with a written statement describing the defect
and application the product is used in. Ashly Audio will examine the product and perform
any necessary service, including replacement of defective parts, at no further cost to you.
Ship your product to:
Ashly Audio Inc.
Attn: Service Department
847 Holt Road
Webster, NY 14580-9103
For units purchased outside The United States of America, service will be provided by an
authorized distributor of ASHLY AUDIO INC.
Obtaining Warranty Service Outside the United States For units purchased outside The
United States of America, service will be provided by an authorized distributor of ASHLY
AUDIO INC.
All Rights Reserved
Physical Mixer
MX-508
Description
–5 -4
Installation –&5Cables – 5
Connectors
OperationDescription
Physical
–7
-6
Troubleshooting
Installation
–7 -8
Spec Table
Typical
Applications
-9
-8
Measurements
Factory
Configs- -10
8
Dimensions - 11 - 9
Troubleshooting
Warranty - 12- 9
Dimensions
Specifications - 10
Warranty - 11
Copyright© 2006 – Ashly Audio Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement