Radio Shack ET-1126 Owner`s manual

Radio Shack ET-1126 Owner`s manual
43-1126.fm Page 1 Thursday, April 27, 2000 11:23 AM
ET-1126 Dual Keypad 900 MHz
Digital Spread Spectrum
Cordless Telephone
Please read before using this equipment.
Owner’s Manual
with Caller ID and Call Waiting ID
43-1126.fm Page 2 Thursday, April 27, 2000 11:23 AM
ˆ Contents
Features .................................................................................................................................. 4
Installation .............................................................................................................................. 8
Mounting the Phone .......................................................................................................... 8
On a Desk Top, Shelf, or Table .................................................................................. 8
On a Wall Plate or Wall .............................................................................................. 9
Connecting and Charging the Battery Pack .................................................................... 10
A Quick Look at the Handset .......................................................................................... 11
Setting the Dialing Mode ................................................................................................. 12
Setting the Ringer TONE/VOLUME ................................................................................ 12
Turning Auto Talk On/Off ................................................................................................. 12
Turning Caller ID/ Call Waiting On/Off ............................................................................ 13
Storing Your Area Code .................................................................................................. 13
Operation .............................................................................................................................. 13
Making and Receiving Calls ............................................................................................ 13
Selecting the Channel .............................................................................................. 14
Adjusting the Handset Volume ................................................................................. 14
Using the Speakerphone ................................................................................................. 14
Switching Between the Handset and Speakerphone ............................................... 14
Using Both the Handset and Speakerphone ............................................................ 14
Using Hold ....................................................................................................................... 14
Using Mute ...................................................................................................................... 15
Using Redial .................................................................................................................... 15
Using Flash ..................................................................................................................... 15
Using Tone Services On a Pulse Line ............................................................................. 15
Using Page/Intercom ....................................................................................................... 16
Transferring a Call Between the Handset and Base ................................................ 16
Memory Dialing ............................................................................................................... 16
Storing a Number in the Handset’s Memory ............................................................ 16
Editing or Deleting a Number in the Handset’s Memory .......................................... 17
Storing a Number in the Base’s Memory ................................................................. 18
Entering a Pause ..................................................................................................... 18
Reviewing the Handset’s Memory Numbers ............................................................ 18
Dialing a Memory Number ....................................................................................... 18
Chain-Dialing Service Numbers ............................................................................... 19
Testing Stored Emergency Numbers ....................................................................... 19
Using a Headset .............................................................................................................. 19
© 2000 Tandy Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks used by Tandy Corporation.
2
43-1126.fm Page 3 Thursday, April 27, 2000 11:23 AM
Caller ID Operation .........................................................................................................
Reviewing Caller ID Records ..................................................................................
Caller ID Messages .................................................................................................
Adding/Deleting the Area Code ...............................................................................
Dialing Numbers from a Caller ID Record ...............................................................
Storing a Caller ID Record to Memory ....................................................................
Deleting Caller ID Records ......................................................................................
19
19
20
20
20
21
21
Troubleshooting ................................................................................................................... 22
Care and Maintenance .........................................................................................................
Replacing the Battery Pack ............................................................................................
The FCC Wants You To Know ........................................................................................
Lightning .........................................................................................................................
24
25
26
26
WARNING: To reduce the risk of fire or
shock hazard, do not expose this product to rain
or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
!
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
This symbol is intended to alert
you to the presence of uninsulated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to constitute a risk of electric shock. Do
not open the product’s case.
!
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accompanying this product.
3
43-1126.fm Page 4 Thursday, April 27, 2000 11:23 AM
ˆ Features
Your RadioShack Dual Keypad 900 MHz
Digital Spread Spectrum Cordless Telephone uses the most advanced cordless
telephone technology to give you superior
audio quality and extended range.
Two-Way Intercom/Paging System — lets
you send a signal from the base to the handset, or from the handset to the base, to page
someone or locate the handset when it is
away from the base. If someone answers,
you can use the phone as an intercom.
The phone’s Caller ID records each caller’s
telephone number (and name, if available in
your area) and the date and time of the call,
as provided by your local phone company to
Caller ID service subscribers.
Auto Talk — lets you set the handset so you
can answer a call by simply lifting the handset from the base or by pressing any key
when the handset is away from the base.
And, if you subscribe to Call Waiting with
Caller ID, the phone shows you the incoming
caller information, even when you are already on the phone.
Your phone has these features:
900 MHz Operation — provides longer
range and less interference than many other
cordless phones.
Spread Spectrum Technology — spreads
the signal across several frequencies, providing additional security for your phone conversations.
Caller ID Memory — stores up to 50 Caller
ID records.
Dual Keypad — a full set of keys on both the
handset and base let you use either keypad
to operate the phone.
Headset Jack — lets you connect an optional headset (available from your local RadioShack store) for hands-free convenience.
Volume Control — lets you adjust the volume you hear through the handset.
Adjustable Ringers — you can set different
volumes for the handset and base ringers.
Ample Talk and Standby Time — the supplied battery (when fully charged) provides
about 6 hours of talk time or 7 days of standby time.
20 Channels — automatically selects a clear
channel when you make or answer a call.
Security Access-Protection Code — automatically prevents other cordless phone users from using your phone line while the
handset is off the base.
Speakerphone — lets you make or answer
calls without using the handset.
Redial — lets you quickly redial any of the
three last numbers dialed on the handset
and the last number dialed on the base.
3-Line Liquid Crystal Display — lets you
view an entire Caller ID record on one
screen.
Tone/Pulse Dialing — lets you use either
type of service.
30-Number Memory Dialing — lets you
store up to 30 numbers (20 in the handset
and 10 in the base) in memory for easy dialing.
4
Hearing-Aid Compatibility — lets you use
your phone with hearing aids that have a T
(telephone) switch.
Features
43-1126.fm Page 5 Thursday, April 27, 2000 11:23 AM
This telephone is UL listed and has been
tested and found to comply with all applicable FCC standards.
IMPORTANT CALLER ID
INFORMATION
To use the phone’s Caller ID and Caller ID
with Call Waiting features, you must be in an
area where those services are available and
you must subscribe to those services
through your local phone company.
Where Caller ID is offered, one or more options are generally available:
than one phone or other device on the line,
add up all the RENs. If the total is more than
five, your phones might not ring. In rural areas, a total REN of three might impair ringer
operation. If ringer operation is impaired, remove a device from the line.
FCC STATEMENT
This telephone complies with Part 68 of FCC
Rules. You must, upon request, provide the
FCC registration number and the REN to
your phone company. These numbers are on
the bottom of the phone’s base.
Note: You must not connect your phone to
any of the following:
• caller’s number only
• caller’s name only
• coin-operated systems
• caller’s name and number
• party-line systems
• most electronic key phone systems
Important:
Cordless phones such as this one require
AC power to operate. When the AC power is
off, you cannot dial out or receive incoming
calls using your phone. To be safe, you
should also have a phone that does not need
AC power to operate (not a cordless phone)
so you can still make and receive calls if
there is an AC power failure.
This telephone complies with the limits for a
Class B digital device as specified in Part 15
of FCC Rules. These limits provide reasonable protection against radio and TV interference in a residential area. However, your
equipment might cause TV or radio interference even when it is operating properly. To
eliminate interference, you can try one or
more of the following corrective measures.
When AC power is lost, the phone loses the
security access-protection code connection
between the base and the handset. When
power is restored, put the handset on the
base briefly to restore this connection so you
can use the handset.
• Reorient or
antenna.
relocate
the
receiving
• Increase the distance between the
equipment and the radio or TV.
• Use outlets on different electrical circuits
for the equipment and the radio or TV.
READ THIS BEFORE
INSTALLATION
Each device that you connect to the phone
line draws power from the phone line. We refer to this power draw as the device’s ringer
equivalence number, or REN. The REN is on
the bottom of the base. If you are using more
Consult your local RadioShack store if the
problem still exists.
Features
5
43-1126.fm Page 6 Thursday, April 27, 2000 11:23 AM
IMPORTANT SAFETY
INSTRUCTIONS
heating, the openings must not be
blocked or covered. The openings
should never be blocked by placing the
product on a bed, sofa, rug, or other
similar surface. This product should
never be placed near or over a radiator
or heat register. This product should not
be placed in a built-in installation unless
proper ventilation is provided.
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock
and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions
marked on the product.
3. Never install telephone wiring during a
lightning storm.
4. Never install telephone jacks in wet
locations unless the jacks are specifically designed for wet locations.
5. Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the network interface.
6. Use caution when installing or modifying
telephone lines.
7. Do not affix the AC power supply cord to
building surfaces with metal fittings (if
the product has an AC power cord).
8. Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
9. Do not use this product near water. For
example, near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
10. Do not place this product on an unstable
cart, stand, or table. The product may
fall, causing serious damage to the
product.
12. This product should be operated only
from the type of power source indicated
on the marking label. If you are not sure
of the type of power supply to your
home, consult your local power company.
13. Do not allow anything to rest on the
power cord. Do not locate this product
where the cord will be stepped on.
14. Do not overload wall outlets and extension cords. Doing so can result in a risk
of fire or electric shock.
15. Never push objects of any kind into this
product through cabinet slots as they
may touch dangerous voltage points or
short out parts that could result in a risk
of fire or electric shock. Never spill liquid
of any kind on the product.
16. To reduce the risk of electric shock, do
not disassemble this product. Take it to
a qualified serviceman when service or
repair work is required. Opening or
removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause electric
shock when the product is subsequently
used.
17. Unplug this product from the wall outlet
and refer servicing to qualified service
technicians under these conditions:
11. Slots and openings in the cabinet and
the back or bottom are provided for ventilation. To protect the phone from over6
Features
• When the power cord plug is damaged or frayed.
43-1126.fm Page 7 Thursday, April 27, 2000 11:23 AM
• If liquid has been spilled into the
product.
and may cause damage to the eyes or
skin. It may be toxic if swallowed.
• If the product has been exposed to
rain or water.
4. Exercise care in handing the battery
pack in order not to short it with conducting materials such as rings, bracelets
and keys. The battery or conductor may
overheat and cause burns.
• If the product does not operate normally when you follow the operating
instructions. Adjust only those controls that are covered by the operating instructions because improper
adjustments of other controls may
result in damage and will often
require extensive work by a qualified
technician to restore the product to
normal operation.
• If the product has been dropped or
the cabinet has been damaged.
• If the product exhibits a distinct
change in performance.
5. Charge the battery pack provided with or
identified for use with this product only in
accordance with the instructions and
limitations specified in the instruction
manual provided for this product.
6. Observe proper polarity orientation
between the battery pack and battery
charger.
SAVE THESE
INSTRUCTIONS
18. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
19. Do not use the telephone to report a gas
leak while in the vicinity of the leak.
BATTERY SAFETY
INSTRUCTIONS
Caution: To reduce the risk of fire or injury,
read and follow these instructions.
1. Use only the appropriate type and size
battery pack specified in the instruction
manual provided for this product.
2. Do not dispose of the battery pack in a
fire. The cell may explode. Check with
local codes for possible special disposal
instructions.
3. Do not open or mutilate the battery
pack. Released electrolyte is corrosive
Features
7
43-1126.fm Page 8 Thursday, April 27, 2000 11:23 AM
ˆ Installation
MOUNTING THE PHONE
You can place the phone’s base on a desk or
table, mount it on a standard wall plate, or
mount it directly on a wall. Choose a location
that is:
• near an AC outlet
Note: Your telephone connects directly to a
modular telephone line jack. If your phone
line jack is not a modular jack, you can update the wiring yourself, using jacks and
adapters available at your local RadioShack
store. Or, you can let the phone company update the wiring for you.
The USOC number of the jack to be installed
is RJ11C (RJ11W for a wall plate).
• near a modular telephone line jack
• out of the way of normal activities
On a Desk Top, Shelf, or Table
• away from electrical machinery, electrical appliances, metal walls or filing cabinets, wireless intercoms, alarms, and
room monitors
1. Plug one end of the supplied long modular cord into the TEL LINE jack on the
back of the base.
• away from other cordless phones
The base’s location affects the phone’s
range. If you have a choice of several locations, try each to see which provides the best
performance.
Cautions:
You must use a Class 2 power
source that supplies 9V AC
and delivers at least 350 mA.
Its center tip must be set to positive and
its plug must fit the phone's DC IN 9V
jack. The supplied adapter meets these
specifications. Using an adapter that
does not meet these specifications
could damage the phone or the adapter.
!
2. Plug the modular cord’s other end into a
modular telephone line jack.
3. Insert the supplied AC adapter’s barrel
plug into the DC IN 9V jack on the back of
the base.
• Always connect the AC adapter to the
phone before you connect it to AC
power. When you finish, disconnect the
adapter from AC power before you disconnect it from the phone.
8
Installation
43-1126.fm Page 9 Thursday, April 27, 2000 11:23 AM
4. Route the adapter’s cord through the
strain relief slot on the bottom of the
base.
5. Plug the modular cord’s other end into
the wall plate jack, then align the
bracket’s keyhole slots with the wall
plate studs and slide the phone downward to secure it.
RING VOL
OFF-LO-HI
5. Plug the adapter into a standard AC outlet.
6. Lift the base’s antenna to a vertical position.
On a Wall Plate or Wall
1. Insert the two tabs at the top of the narrow end of the supplied bracket into the
base’s upper tab slots, then press down
on the bracket’s latches and insert them
into the lower slots.
6. Plug the adapter into a standard AC outlet.
7. Press and lift out the handset holder.
Rotate it 180°, then snap it back into
place so it holds the handset.
8. Lift the base’s antenna to a vertical position.
RING VOL
OFF-LO-HI
Note: To mount the phone directly on a wall,
you need two screws (not supplied) with
heads that fit into the keyhole slots on the
bottom of the base.
Follow the steps under “On a Wall Plate or
Wall,” then apply these additional instructions.
2. Plug one end of the supplied short modular cord into the TEL LINE jack on the
back of the base as in “On a Desk Top,
Shelf, or Table,” Step 1.
3. Insert the supplied AC adapter’s barrel
plug into the DC IN 9V jack as in “On a
Desk Top, Shelf, or Table,” Step 3.
1. Drill two holes
315/16 inches (100
mm) apart. Then
thread a screw
into each hole,
letting the heads
extend about 3/16
inch (5 mm) from
the wall.
3
/16 Inch
315/16
Inches
4. Route the adapter and modular cords
through the grooves on the bracket.
Installation
9
43-1126.fm Page 10 Thursday, April 27, 2000 11:23 AM
2. Plug one end of the supplied long modular cord into the TEL LINE jack on the
back of the base and route the adapter
cable and modular cords through the
grooves on the bracket.
3. Plug the battery pack’s connector into
the socket in the compartment (the connector fits only one way), then replace
the battery pack.
4. Replace the cover.
3. Align the bracket’s keyhole slots with the
mounting screws and slide the phone
downward to secure it.
To charge the battery pack, place the handset on the base either faceup or facedown.
The CHARGE indicator on the base lights
and Total:00 appears on the handset display.
Recharge the battery pack when Low Bat-
tery flashes on the display.
Important: Be sure the battery pack is properly connected before you try to charge it.
The CHARGE indicator lights when the
handset is on the base, even if the battery
pack is not connected.
CONNECTING AND
CHARGING THE BATTERY
PACK
Notes:
The phone comes with a rechargeable nickel-cadmium battery pack in the handset but
not connected. Before using your phone, you
must connect the battery pack and then
charge it for about 24 hours.
1. Press down and slide off the battery
pack compartment cover.
2. Lift the battery pack out of the compartment.
10
• When you first use the phone after
charging or recharging the battery pack,
the phone might not work and you might
hear an error tone when you press
TALK. If this happens, return the handset to the base for about 5 seconds. This
resets the security access-protection
code.
• If the base loses power for 60 minutes
while the handset is away from it or the
handset’s battery pack is completely discharged, the security access-protection
code might be lost. To reset the code,
return the handset to the base for about
5 seconds.
• Using a pencil eraser, clean the charging contacts on the handset and the
base about once a month.
Installation
43-1126.fm Page 11 Thursday, April 27, 2000 11:23 AM
• If the battery pack becomes weak during
a call, the handset beeps every 3 seconds and Low Battery flashes. If this
happens, you cannot make another call
on the phone until you recharge the battery pack.
• About once a month, fully discharge the
battery pack by keeping the handset off
the base until Low Battery flashes.
Otherwise, the battery pack loses its
ability to fully recharge.
• If the display is blank and the phone
does not work, recharge the battery
pack. (The battery power might be too
low to light the display.)
• If you are not going to use your phone
for an extended period of time, disconnect the battery pack. This increases the
battery pack’s usable life.
• The supplied battery pack should last for
about a year. When it loses its ability to
fully recharge, order a replacement battery pack from your local RadioShack
store (see “Replacing the Battery Pack”
on Page 25).
A QUICK LOOK AT THE HANDSET
Use MEM to store or recall
names and numbers in memory (see “Memory Dialing” on
Page 16).
Use TALK to make a
call (see “Making and
Receiving Calls” on
Page 13).
Use CALL ID to review the
Caller ID records.
Press 8 VOL/CID 9 to adjust
the handset volume (see “Adjusting the Handset Volume” on
Page 14), view Caller ID records
(see “Caller ID Operation” on
Page 19), or select options.
Press TONE to use your
phone company’s special
tone services on a pulse
line (see “Using Tone
Services On a Pulse
Line” on Page 15).
Press DELETE to erase
information if you make a
mistake.
Press FLASH to use the
phone’s flash function (see
“Using Flash” on Page 15).
Press REDIAL/PAUSE to select a phone number so you
can redial it (see “Using Redial” on Page 15) or store a
pause in a number (see “Entering a Pause” on Page 18).
Press CH/SELECT to select
the phone’s channels (see
“Selecting the Channel” on
Page 14) and other options.
Press INTCM to page someone at
the base or transfer a call to the
base (see “Using Page/Intercom”
on Page 16).
Installation
11
43-1126.fm Page 12 Thursday, April 27, 2000 11:23 AM
SETTING THE DIALING
MODE
Set DIAL MODE on the back of the base for
the type of service you have. If you are not
sure which type you have, once the battery
pack is fully charged, do this test.
1. Be sure DIAL MODE is set to T (tone).
Note: Pressing VOL/CID 8 when the phone
is set to Ringer A High or VOL/CID 9
when the phone is set to Ringer B Low
does not change the setting. Press the opposite arrow key to change the setting.
To set the base’s ringer volume, set RING
VOL on the back of the base to OFF, LO, or HI.
Notes:
DIAL MODE
• When you set RING VOL to OFF, the
base (and the handset if it is on the
base) does not ring but another phone
connected to the same line rings. If the
handset is away from the base, the
handset also rings.
2. Lift the handset, press TALK, and listen
for a dial tone.
• When you set the auto talk function to
off, the handset rings when you lift the
handset from the base. See “Turning
Auto Talk On/Off.”
3. Press any number except 0.
Note: If your phone system requires that
you dial an access code (9, for example)
before you dial an outside number, do
not press the access code number
either.
If the dial tone stops, you have touch-tone
service. Leave DIAL MODE set to T.
If the dial tone continues, you have pulse
service. Set DIAL MODE to P (pulse).
SETTING THE RINGER
TONE/VOLUME
You can select one of four different ringer
tone/volume settings on the handset. At any
time, except during a call, repeatedly press
VOL/CID 8 or 9 to select the desired ringer
setting. Each time you press a button, the
phone rings at the selected setting and the
display shows Ringer A High, Ringer A
Low, Ringer B High, or Ringer B Low.
12
TURNING AUTO TALK ON/
OFF
Your phone is preset so you must press
TALK when you lift the handset from the base
to answer a call. With auto talk turned on,
you can answer a call by just lifting the handset from the base. If the handset is away
from the base, you can answer by pressing
any key.
Follow these steps to turn auto talk on or off.
1. Lift the handset and hold down CALL ID.
A menu appears with Auto Talk
selected.
2. Press CH/SELECT to change the auto
talk setting. On or Off appears indicating the selected setting.
Return the handset to the base or press
CALL ID to store the new setting.
Installation
43-1126.fm Page 13 Thursday, April 27, 2000 11:23 AM
TURNING CALLER ID/ CALL
WAITING ON/OFF
dial the area code (or store in the memory),
you can add it afterwards. “Adding/Deleting
the Area Code” on Page 20.
If you subscribe to Call Waiting with Caller ID
service, you can set the phone to show Caller ID information for an incoming call even
while you are using the phone.
Note: If your calling area requires 10-digit dialing including area code, do not enter the
area code but leave this option blank.
Follow these steps to turn the Caller ID/ Call
Waiting feature on or off.
1. Lift the handset and hold down CALL ID.
2. Press 2 or VOL/CID 9 to select CIDCW
(Caller ID/Call Waiting).
3. Press CH/SELECT to change the Caller
ID/Call Waiting setting. On or Off
appears indicating the selected setting.
Return the handset to the base or press
CALL ID to store the new setting.
STORING YOUR AREA
CODE
You can store your local area code in the
phone’s Caller ID record so it does not store
the area code if the received call is from your
local area. If for some reason you need to
Follow these steps to store your area code.
1. Lift the handset and hold down CALL ID.
2. Press 3 or VOL/CID 9 twice to select
Area Code.
3. Press CH/SELECT, then enter your threedigit area code. If you make a mistake,
repeatedly press 6 or 7 to move the
cursor over the incorrect digit, then enter
the correct number.
Note: If an area code is already stored, it appears on the display. To delete the area
code, press DELETE three times. Then enter
your area code. Or you can use 6 or 7 to
move the cursor and edit the area code.
Press CH/SELECT to store the area code,
then press CALL ID or return the handset to
the base to clear the display.
ˆ Operation
MAKING AND RECEIVING
CALLS
You can also dial the number before you
press TALK.
To make a call, lift the handset and press
TALK. Talk and the current volume setting
(see “Adjusting the Handset Volume” on
Page 14) appear on the handset’s display,
and the CHARGE/IN USE indicator on the
base lights. Then dial the number. The number displays on the handset as you dial, then
the call’s elapsed time displays.
If you make a mistake, press DELETE until
the incorrect entry is erased, then enter the
correct number. To delete the entire number,
hold down DELETE for at least 2 seconds.
Operation
13
43-1126.fm Page 14 Thursday, April 27, 2000 11:23 AM
When you receive a call, Incoming Call
appears on the display. To answer it, lift the
handset from the base and press TALK. If
auto talk is on, just lift the handset from the
base or press any key. Talk and the current
volume setting appear on the display.
To end a call, place the handset on the base
or press TALK.
Selecting the Channel
The phone has 20 channels. If the call
seems to disconnect for no reason during a
call, press CH/SELECT on the handset to select a different channel. Scanning appears
while your phone searches for a clear channel.
Adjusting the Handset Volume
To adjust the volume of the sound you hear
through the handset during a call, press VOL/
CID 8 or 9 until you obtain the desired volume level. Volume Maximum, Volume
High, Volume Medium, or Volume Low
appears on the display.
Once you set the volume level, the setting is
maintained even after you hang up the
phone.
Note: When you press VOL/CID8
8 while the
volume is maximum or VOL/CID9 while the
volume is low, the setting does not change
and an error tone sounds.
USING THE
SPEAKERPHONE
To end a speakerphone call, press SPEAKER
again.
Switching Between the Handset
and Speakerphone
To switch to the speakerphone while you are
using the handset, press SPEAKER on the
base. When you hear the conversation or
dial tone on the speakerphone, press TALK
on the handset.
To switch to the handset while you are using
the speakerphone, simply lift the handset off
the base. If the handset is away from the
base, press TALK, then press SPEAKER.
Using Both the Handset and
Speakerphone
If someone else is using the speakerphone,
press TALK on the handset to join the conversation.
If someone else is using the handset, press
SPEAKER on the base to join the conversation.
During the call, one person can hang up and
another person can continue the call at the
other keypad. Or, both people can hang up
at the same time to end the call.
Note: If you hear a high-pitched noise from
the base’s speaker, the handset and the
base are too close together.
USING HOLD
To make or answer a call using the speakerphone, press SPEAKER. The SPEAKER indicator lights. When you hear a dial tone, dial
the number.
Press HOLD to put a speakerphone call on
hold. The HOLD indicator lights. While a call
is on hold, you can make an intercom call
(see “Using Page/Intercom” on Page 16) between the handset and the base without disconnecting the call.
To set the speakerphone’s volume, slide
VOLUME on the right side of the base.
14
Operation
43-1126.fm Page 15 Thursday, April 27, 2000 11:23 AM
To release a call from hold, lift the handset
and press TALK, press SPEAKER or HOLD on
the base, or pick up any extension phone on
the same line.
• The redial memory holds up to 32 digits,
so you can redial long-distance as well
as local numbers.
• The redial memory also holds pause
entries. See “Entering a Pause” on
Page 18.
USING MUTE
While talking on the speakerphone, you can
temporarily turn off the phone’s microphone
by pressing MUTE so the other party cannot
hear you. The SPEAKER indicator flashes.
Press MUTE or SPEAKER to resume your
conversation.
USING FLASH
FLASH performs the electronic equivalent of
a switchhook operation for special services,
such as Call Waiting.
For example, if you have Call Waiting, press
Hint: If the phone is close to loud noises
while you are using the speakerphone, the
phone might not switch to let you hear the
person on the other end of the line. If this
happens, press MUTE to turn off the microphone so you can hear the caller. Press
MUTE again to speak.
FLASH to answer an incoming call without
disconnecting the current call. Press FLASH
USING REDIAL
USING TONE SERVICES ON
A PULSE LINE
You can quickly dial any of the last three
numbers you dialed recently on the handset.
Lift the handset and repeatedly press REDIAL/PAUSE until the number you wish to dial
displays. Then press TALK and the phone dials the number.
again to return to the first call.
Note: If you do not have any special phone
services, pressing FLASH might disconnect
the current call.
Some special services, such as bank-byphone, require tone signals. If you have
pulse service, you can still use these special
tone services by following these steps.
1. Be sure DIAL MODE is set to P.
To dial the last number dialed using the
base, press SPEAKER then REDIAL.
Notes:
• The redial memory for each keypad is
separate. You cannot redial a number
you dialed on the handset’s keypad
using REDIAL on the base’s keypad, and
vice versa.
2. Dial the service’s main number.
3. When the service answers, press TONE/
on the handset (TONE on the base).
Any additional numbers you dial are
sent as tone signals.
When you hang up, the phone automatically
resets to pulse dialing.
• On the handset, you can also press
REDIAL/PAUSE after pressing TALK to
dial the last number dialed.
Operation
15
43-1126.fm Page 16 Thursday, April 27, 2000 11:23 AM
USING PAGE/INTERCOM
You can use the phone as a two-way pager
and intercom between the base and the
handset. This is useful if the handset is away
from the base and you want to locate it, or if
you want to converse with someone through
the intercom.
To page the base from the handset, press INTCM. Paging Base appears, and the base
and handset ring. Press SPEAKER or INTERCOM on the base to answer the page. Intercom appears on the handset’s display.
To page the handset from the base, press INTERCOM. The handset and base ring, and
Paging appears on the handset’s display.
Press TALK or INTCM on the handset to answer the page. Intercom appears.
To end an intercom call, press TALK on the
handset, press SPEAKER on the base, or
hang up the handset.
If a call comes in during an intercom conversation, either the person at the base or the
person at the handset can answer the call.
Press TALK on the handset or SPEAKER on
the base once to end the intercom call, then
press TALK or SPEAKER again to answer the
incoming call.
Note: You can use the intercom while a call
is on hold, but not during a conversation.
When the person at the base answers, press
TALK. The call is released from hold and
transferred to the base.
To return to handset use, press TALK again.
To transfer a call from the base to the handset, press INTERCOM. The call is placed on
hold, and Paging and Hold appear on the
handset’s display. When the person with the
handset answers, press SPEAKER. The call
is released from hold and transferred to the
handset. To return to base use, press
SPEAKER again.
MEMORY DIALING
You can store up to 30 numbers in memory
(20 in the handset’s and 10 in the base’s
memory), then dial a stored number by
pressing a memory location number.
You can also store a name with each number
in the handset’s memory.
Use the supplied memory directory sticker to
record your stored numbers. Peel the backing from the sticker and attach it to the
base’s handset cradle.
Storing a Number in the Handset’s
Memory
Notes:
• An error tone sounds and the phone
exits the storing process if you wait
more than 20 seconds between each
keypress.
Transferring a Call Between the
Handset and Base
You can use the phone’s intercom feature to
transfer a call between the handset and the
base.
To transfer a call from the handset to the
base, press INTCM. The call is put on hold,
and Paging Base and Hold appear.
• If you receive a call during memory
entry, the phone exits the storing process.
Follow these steps to store a number in the
handset’s memory.
1. Lift the handset.
16
Operation
43-1126.fm Page 17 Thursday, April 27, 2000 11:23 AM
2. Hold down MEM until Memory Store
and a list of memory location numbers
appears.
3. Press a number (01–20) or repeatedly
press 8 or 9 to choose a two-digit
memory location. Precede a single digit
location number with 0 – 01, 02, 03, and
so on.
On a Pulse Line” on Page 15 and
“Entering a Pause” on Page 18).
8. Press CH/SELECT. The phone beeps
and Memory nn Stored appears.
After 2 seconds, Memory Store
appears. Repeat Steps 3–8 to store
more numbers.
9. When you finish, press MEM.
4. Press CH/SELECT.
appears.
Store
Name
To replace a stored number, store a new one
in its place.
If you do not want to enter a name, skip
to Step 6. <Memory nn> appears to
identify the number (nn is the memory
location number you selected).
5. To enter a name, press VOL/CID 8 or 9
to select the characters. Press 6 or 7
to move the cursor left or right.
Repeatedly press VOL/CID 9 to view the
characters in alphabetical order. (The
display shows uppercase letters first,
then lowercase letters, numbers, and
special characters.)
Editing or Deleting a Number in
the Handset’s Memory
Follow these steps to edit or delete a memory number.
1. Lift the handset.
2. Hold down MEM until Memory Store
and a list of memory location numbers
appear on the display.
Notes:
3. Choose a memory location (01-20) by
pressing a number or by repeatedly
pressing VOL/CID 8 or 9.
• Press VOL/CID 8 to see the characters in reverse alphabetical order.
4. Press CH/SELECT. A menu appears with
three options.
• You can hold down VOL/CID 8 or 9
to scroll rapidly through the characters.
• If you make a mistake, move the cursor over the error, then enter the correct character, or press DELETE to
delete a character. To delete all the
characters, hold down DELETE for at
least 1 second.
6. Press CH/SELECT. Store Number
appears.
7. Enter the phone number and any tone or
pause entries (see“Using Tone Services
Operation
Edit Memory nn — edit the record as
described in Steps 5 through 7 of “Storing a Number in the Handset’s Memory”
on Page 16.
Delete Memory nn — The display
prompts you to confirm the deletion.
Press VOL/CID 8 to move the cursor to
Yes, then press CH/SELECT or DELETE.
The phone beeps, and Memory nn
Deleted appears.
Go Back — Returns you to the list of
memory numbers.
17
43-1126.fm Page 18 Thursday, April 27, 2000 11:23 AM
5. Press VOL/CID 8 or 9 to highlight the
desired option then press CH/SELECT to
choose it.
Storing a Number in the Base’s
Memory
Note: An error tone sounds and the phone
exits the storing process if you wait more
than 20 seconds between each keypress.
with the phone number. However, you
should also store a pause after the access
code to allow the outside line time to connect.
To enter a 2-second pause, press PAUSE
(REDIAL/PAUSE on the handset). P appears
on the display if you are storing a number
into the handset’s memory. You can add
more pause entries for a longer pause.
1. Press MEM. The CHARGE/IN USE indicator blinks.
Reviewing the Handset’s Memory
Numbers
2. Enter the number (up to 16 digits) and
any tone or pause entries (see“Using
Tone Services On a Pulse Line” on
Page 15 and “Entering a Pause” on
Page 18).
To review your handset’s memory numbers,
press MEM. The list of memory location numbers (01–20) appears with the name stored
with each number (or <Memory nn> if you
did not store a name).
Notes:
• An error tone sounds and the phone
exits the storing process if you enter
more than 16 digits.
• Each tone or pause entry uses one
digit of memory.
3. Press MEM again, then enter the memory location number (0–9) where you
want to store the phone number. A tone
sounds indicating that the number is
stored.
To see the stored phone numbers, press 7.
An arrow to the right of the number means it
is longer than 13 digits. Press 7 again to
see the rest of the number. Repeatedly press
6 to return to the name display.
To exit the memory number list, press MEM.
To see a stored name and phone number at
the same time, press CH/SELECT when the
cursor is by a memory location number. To
exit this display, hold down DELETE until the
display clears.
To replace a number in the base’s memory,
simply store a new number in its place. To
erase a memory number, press MEM twice,
then press the memory location number (0–
9) you want to erase. A tone sounds indicating that the memory location has been
erased.
Dialing a Memory Number
Entering a Pause
To dial a number stored in the base’s memory, press SPEAKER. When you hear a dial
tone, press MEM, then press the memory location number for the number you want to dial.
In some telephone systems, you must dial an
access code (9, for example) and wait for a
second dial tone before you can dial an outside number. You can store the access code
18
To dial a number stored in the handset’s
memory, lift the handset and press MEM. The
list of memory location numbers appears.
Choose a memory location (01–20) by pressing a number or by repeatedly pressing 8 or
9, then press TALK.
Operation
43-1126.fm Page 19 Thursday, April 27, 2000 11:23 AM
Note: If you select an empty memory location, the base beeps.
Chain-Dialing Service Numbers
For quick recall of numbers for special services (such as bank by phone), store each
group of numbers in its own memory location. Dial the service’s main number first.
Then, at the appropriate place in the call,
press MEM and the number for the location
where the additional information is stored.
With a headset connected, you can make or
answer calls as usual using the speakerphone or the keys on the handset.
You can use a handset holder (available
from your local RadioShack store) to hang
the handset on your belt for greater convenience.
When you finish using the headset, disconnect it from the handset and close the rubber
cover to protect the jack.
CALLER ID OPERATION
Testing Stored Emergency Numbers
If you store an emergency service’s number
(police department, fire department, ambulance) and you choose to test the stored
number, make the test call during the late
evening or early morning hours to avoid peak
demand periods. Also, remain on the line to
explain the reason for your call.
USING A HEADSET
You can talk with hands-free convenience
using an optional headset that has a 3/32 inch (2.5-mm) plug. Contact your local RadioShack store for a suitable headset.
To connect the headset, open the rubber
on the side of the handset,
cover marked
then insert the headset’s plug into the jack.
Notes:
• Connecting a headset disconnects the
handset’s earpiece and microphone.
• VOL/CID 8 or 9 on the handset also
controls the connected headset’s volume.
• If you place the handset on the base to
recharge it while the headset is connected, be sure the handset seats properly.
If you subscribe to Caller ID service from
your phone company, the phone company
sends information about the call, as well as
the time and date, between the first and second rings of every call you receive.
The phone displays this information after the
second ring, and it stores up to 50 Caller ID
records for later review. It also shows if caller
information is unavailable or if the name and
number were blocked by the caller (“Caller
ID Messages” on Page 20).
If you subscribe to Call Waiting with Caller
ID, you will hear a tone through the handset
when a call comes in, then the Caller ID
record appears. If you want to answer the incoming call, press FLASH. To resume the
previous phone conversation, press FLASH
again.
If the phone’s Caller ID memory becomes
full, any new call replaces the oldest call’s
record.
Reviewing Caller ID Records
If the handset is faceup on the base, it shows
the number of new Caller ID records, if any,
and the total number of records.
To review the contents of each Caller ID
record, lift the handset and press CALL ID to
recall the number of records on the display.
Operation
19
43-1126.fm Page 20 Thursday, April 27, 2000 11:23 AM
Then, repeatedly press VOL/CID 9 to scroll
through the Caller ID records from the newest to the oldest, or VOL/CID 8 to scroll back
through the records. To scroll quickly through
the records, hold down VOL/CID 8 or 9.
The top line of each record shows the date,
time and the number of calls from that number. The second line shows the caller’s
name, and the third line shows the caller’s
phone number.
When you scroll past the last record, total
record number appears, then the first record.
When you scroll past the first record, the total
record number appears, then the last record.
To exit the Caller ID record display, press
CALL ID.
Caller ID Messages
Display
Description
New:XX
Total:XX
Shows the number of new Caller ID records (records you have not
reviewed) and the total number of records.
Private Name
The caller has blocked the Caller ID information.
or
Private Number
Unknown Name
The caller is not within a Caller ID service area.
or
Unknown Number
Incomplete
Appears if there was an error during the transmission of Caller ID inforData
mation. Occasional errors are normal. If the phone frequently displays
Incomplete Data, contact your local telephone company or RadioShack
store.
Adding/Deleting the Area Code
When the area code of the received call is
the same as the one you stored (see“Storing
Your Area Code” on Page 13), the caller ID
record does not show the area code. If it is
different, the record shows the area code.
However, you can add or delete the area
code on the display. When the record is on
the display, press 3 to add or delete the area
code. Pressing 3 again deletes or adds the
area code.
When you dial the number or store it into
memory, the phone dials or stores the number as it appears on the display.
20
Dialing Numbers from a Caller ID
Record
To dial a local number stored in a Caller ID
record, recall the record, then press TALK. If
it is a long distance call, press 1 (1 appears
before the displayed number) before you
press TALK. If you want to add or delete the
area code, press 3 before you press TALK.
Note: If a Caller ID record does not contain a
phone number (if it was blocked by the caller,
for example) you cannot dial from that
record.
Operation
43-1126.fm Page 21 Thursday, April 27, 2000 11:23 AM
Storing a Caller ID Record to
Memory
The phone beeps once indicating that
the record was deleted.
Follow these steps to store the name and
number from a Caller ID record into a memory location.
1. Press CALL ID then VOL/CID 8 or 9 to
recall the record you want to store.
2. If you want to add or delete the area
code, press 3.
3. Press MEM.
appears.
Select
Location
4. Choose a memory location (01–20) by
pressing a number or by repeatedly
pressing VOL/CID 8 or 9, then press
CH/SELECT.
Follow these steps to delete all Caller ID
records.
1. Press CALL ID so the record totals
appear.
DELETE.
Delete All?
2. Press
appears, prompting you to confirm the
deletion.
3. Press VOL/CID 8 to move the cursor to
Yes, then press CH/SELECT or DELETE.
The phone beeps once and Total:00
appears indicating that all Caller ID
records were deleted.
If the selected location is empty, the
phone beeps to confirm that it stored the
number, then the Caller ID record
appears.
If a record exists in the selected location, Replace Memory? appears,
prompting you to confirm the replacement. Move the cursor to Yes or No,
then press CH/SELECT.
Deleting Caller ID Records
You can delete Caller ID records individually
or all at once.
Follow these steps to delete a single Caller
ID record.
1. Press CALL ID then VOL/CID 8 or 9 to
recall the record you want to delete.
2. Press DELETE. Delete Message?
appears, prompting you to confirm the
deletion.
3. Press VOL/CID 8 to move the cursor to
Yes, then press CH/SELECT or DELETE.
Operation
21
43-1126.fm Page 22 Thursday, April 27, 2000 11:23 AM
ˆ Troubleshooting
We do not expect you to have any problems with your phone, but if you do, these suggestions
might help.
Problem
The phone does not work or works
poorly.
Suggestion
Be sure the base’s phone line cord and AC adapter
are correctly and securely connected.
Be sure the battery pack in the handset is connected and charged.
Return the handset to the base for about 5 seconds
to reset the security access-protection code.
The display flashes slowly when the
handset is faceup on the base.
Make sure the battery pack in the handset is properly connected.
The handset stops working or works
poorly during a call.
Move the handset closer to the base.
Lift the base’s antenna to a fully vertical position.
Be sure the handset’s battery pack is charged. (If
the battery pack power is too low, the handset cannot display Low Battery.)
Low volume or unusual sounds.
Someone has picked up another phone on the
same line. Hang up the other phone.
Dropout or mute.
Keep the handset away from computers, remote
control toys, wireless microphones, alarm systems,
intercoms, room monitors, fluorescent lights, and
electrical appliances.
Move to another location or turn off the source of
interference.
Press CH/SELECT to change the channel.
Hang up and redial the number.
The phone cannot be operated at a
useful distance from the base because
the signal becomes weak or noisy
(handset’s range has decreased).
Be sure neither the handset’s nor base’s antenna is
touching a metal surface.
Return the handset to the base and recharge the
battery pack.
Lift the base’s antenna to a vertical position.
The handset battery pack does not
charge.
Check the charging contacts on the handset and
base. If they are dirty, clean them with a pencil
eraser.
Be sure the battery pack is connected correctly.
Be sure the handset is properly seated on the base.
Replace the battery pack (see “Replacing the Battery Pack” on Page 25).
22
Troubleshooting
43-1126.fm Page 23 Thursday, April 27, 2000 11:23 AM
Problem
The handset does not ring or receive a
page.
Suggestion
Move the handset closer to the base.
Lift the base’s antenna to a vertical position.
Be sure the battery pack in the handset is connected and charged.
Move the base away from other electrical devices.
You have an incoming call, but do not
receive any Caller ID information.
Let the phone ring twice before you answer so the
phone has time to record the Caller ID information.
Check that the phone is correctly and securely connected.
Check with your phone company to verify that your
Caller ID service is active.
If you still have problems, disconnect the phone. If other phones on the same line work properly, the fault is in this phone or its installation. If you cannot find the problem, take the phone to
your local RadioShack store for assistance.
Troubleshooting
23
43-1126.fm Page 24 Thursday, April 27, 2000 11:23 AM
ˆ Care and Maintenance
Your Radioshack Dual Keypad 900 MHz Digital Spread Spectrum Cordless Telephone is an
example of superior design and craftsmanship. The following suggestions will help you care
for your phone so you can enjoy it for years.
Keep the phone dry. If it gets wet, wipe it dry immediately. Liquids might contain
minerals that can corrode the electronic circuits.
Use and store the phone only in normal temperature environments. Temperature extremes can shorten the life of electronic devices, damage batteries, and
distort or melt plastic parts.
Keep the phone away from dust and dirt, which can cause premature wear of
parts.
Handle the phone gently and carefully. Dropping it can damage circuit boards
and cases and can cause the phone to work improperly.
Use only fresh batteries of the required size and recommended type. Batteries
can leak chemicals that damage your phone’s electronic parts.
Wipe the phone with a damp cloth occasionally to keep it looking new. Do not
use harsh chemicals, cleaning solvents, or strong detergents to clean the
phone.
Modifying or tampering with the phone’s internal components can cause a malfunction and
might invalidate its warranty and void your FCC authorization to operate it. If your phone is
not performing as it should, take it to your local RadioShack store for assistance. If the trouble is affecting the telephone lines, the phone company can ask you to disconnect your
phone until you have resolved the problem.
24
Care and Maintenance
43-1126.fm Page 25 Thursday, April 27, 2000 11:23 AM
REPLACING THE BATTERY
PACK
If you follow the instructions in “Connecting
and Charging the Battery Pack” on Page 10,
the battery pack should last about one year.
If the battery pack does not hold a charge for
more than 2 hours after an overnight charge,
replace it with a new 3.6-volt, 600 mAh battery pack with a connector that fits the socket
in the battery compartment. You can order a
replacement battery pack through your local
RadioShack store.
Install the new battery pack, then charge it
for about 24 hours.
1. Press down and slide off the battery
pack compartment cover.
If you have trouble replacing the battery
pack, take the phone to your local RadioShack store for assistance.
Important: This phone can
use
nickel-cadmium
rechargeable batteries. At the
end of a nickel-cadmium battery’s useful life, it must be recycled
or
disposed
of
properly. Contact your local, county, or state
hazardous waste management authorities
for information on recycling or disposal programs in your area or call 1-800-822-8837.
Some options that might be available are:
municipal curbside collection, drop-off boxes
at retailers such as your local RadioShack
store, recycling collection centers, and mailback programs.
2. Lift the battery pack out of the compartment, then gently pull on the battery
connector to disconnect it.
3. Insert the new battery pack’s connector
into the socket in the compartment,
place the battery pack into the compartment, and replace the cover.
Warning: Dispose of the old battery pack
promptly and properly. Do not burn or bury it.
Cautions:
• You must use a replacement battery
pack of the same size and type.
• Do not dispose of the battery pack in a
fire because it might explode.
• Do not open or mutilate the battery
pack.
• Be careful not to short the battery pack
by touching it with conducting materials,
such as rings, bracelets, and keys. The
battery pack or conductor might overheat and burn.
Care and Maintenance
25
43-1126.fm Page 26 Thursday, April 27, 2000 11:23 AM
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone causes
problems on the phone line, the phone company can temporarily discontinue your service. If this happens, the phone company
attempts to notify you in advance. If advance
notice is not practical, the phone company
notifies you as soon as possible and advises
you of your right to file a complaint with the
FCC.
Also, the phone company can make changes
to its lines, equipment, operations, or procedures that could affect the operation of this
telephone. The telephone company notifies
you of these changes in advance, so you can
take the necessary steps to prevent interruption of your telephone service.
LIGHTNING
Your telephone has built-in protection circuits
to reduce the risk of damage from surges in
telephone line and power line current. These
protection circuits meet or exceed the FCC
requirements. However, lightning striking the
telephone or power lines can damage your
telephone.
Lightning damage is not common. Nevertheless, if you live in an area that has severe
electrical storms, we suggest that you unplug
your phone when storms approach to reduce
the possibility of damage.
26
Care and Maintenance
43-1126.fm Page 27 Thursday, April 27, 2000 11:23 AM
ˆ Notes
Notes
27
43-1126.fm Page 28 Thursday, April 27, 2000 11:23 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
12/99
43-1126
UCZZ0688ZZ
04A00
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement