Epson EMP-TW620 Projector User manual

About the Manuals and Notations Used
Types of Manual
The documentation for your EPSON projector is divided into the following two manuals. Refer to the
manuals in the order given below.
Safety Instructions/World-Wide Warranty Terms
This manual contains information on using the projector safely, and also includes safety instructions,
world-wide warranty terms booklet and a troubleshooting check sheet.
Be sure to read this manual thoroughly before using the projector.
User’s Guide (this manual)
This User's Guide contains information on installing the projector, basic operations, using the
configuration menus, troubleshooting and maintenance.
Notations used in this User’s Guide
General information
Indicates procedures where personal injury or damage to the projector may occur if
the procedures are not followed correctly.
Indicates additional information and points which may be useful to know regarding a
topic.
TIP
Indicates a page where useful information regarding a topic can be found.
Indicates that an explanation of the underlined word or words in front of this symbol
appears in the glossary of terms.
Refer to the "Glossary" in the "Appendix".
p.52
,
etc.
" (Menu Name) "
[ (Name) ]
Indicates buttons on the remote control or projector's control panel.
Indicates configuration menu items.
Example: "Picture"-"Color Mode"
Indicates the port name of the projector.
Example: [InputA]
Meaning of "unit" and "projector"
When "unit" or "projector" appears in the text of this User’s Guide, they may refer to items which are
accessories or optional equipment in addition to the main projector unit itself.
Checking the Components
When you unpack the projector, make sure that you have all these components.
If any of the components are missing or incorrect, please contact the place of purchase.
❏ Projector (with lens cover)
❏ Remote control
❏ Power cable (3.0m)
Connect to the projector and to a wall outlet.
❏ AA alkali batteries (2 pcs.)
Insert into the remote control.
Documentation
❏ Safety Instructions/World-Wide
Warranty Terms
❏ User’s Guide
❏ Quick Start Guide
* Some regions may not have the quick start guide
included as documentation.
❏ D4 SCART adapter
Use a commercially-available SCART cable to
make the connections when projecting RGB-video
and component video images.
* Some regions may not have the D4 SCART adapter
included as an accessory.
1
Table of Contents
■ Features of the Projector............................. 4
■ Part Names and Functions .......................... 6
Front / Top.................................................... 6
Control panel ................................................ 6
Remote control ............................................. 7
Rear.............................................................. 8
Base ............................................................. 8
■ Appearance................................................... 9
Installing the Projector
■ Setting up.................................................... 10
Adjusting the projection size....................... 10
■ Connecting Image Sources ....................... 12
■ Preparing the Remote Control .................. 13
Inserting batteries into the remote control .. 13
Basic Operations
■ Projecting Images ...................................... 14
Turning the power on and
projecting images ..................................... 14
■ Adjusting the Projection Screen............... 16
Focus adjustment ....................................... 16
Fine adjustments to image size
(Zoom adjustment) ................................... 16
Projection image position adjustment
(Lens shift)................................................ 16
Image Quality Adjustments
■ Basic Image Quality Adjustments ............ 18
Selecting the colour mode.......................... 18
Selecting the aspect ................................... 18
■ Advanced Colour Adjustments................. 20
Skin tone adjustment.................................. 20
Absolute colour temperature adjustment.... 20
Gamma adjustment .................................... 20
RGB adjustment (Offset, Gain) .................. 22
Hue and saturation adjustment .................. 22
■ Examining Image Quality Further ............. 23
Sharpness (Advanced) adjustment ............ 23
Auto Iris (automatic aperture) setting ......... 23
■ Viewing Images at a Preset Image Quality
(Memory Function)...................................... 24
Saving image quality adjustments
(Save Memory) ......................................... 24
Retrieving image quality adjustments
(Load Memory) ......................................... 24
Configuration Menu
■ Configuration Menu Functions ................. 26
List of configuration menus ........................ 26
"Picture" menu............................................ 28
"Image" menu ............................................. 29
2
"Settings" menu .......................................... 31
"Memory" menu .......................................... 33
"Reset" menu.............................................. 34
Using the configuration menus................... 34
Table of Contents
■ Optional Accessories / Consumables ..... 46
■ List of Supported Monitor Displays ......... 47
• Cleaning the air filter............................................42
• Cleaning the projector case ..................................42
• Cleaning the lens ..................................................42
• Component Video ................................................ 47
• Composite Video/S-Video ................................... 47
• Analog-RGB signals/signals input
to the [HDMI] input port ................................... 48
Consumable replacement periods ............. 43
• Air filter replacement period ................................43
• Lamp replacement period .....................................43
Replacing consumables............................. 44
• Replacing the air filter ..........................................44
• Replacing the lamp ...............................................44
• Resetting the lamp operating time ........................44
■ Specifications ............................................ 49
■ Glossary ..................................................... 52
■ Index ........................................................... 54
Basic
Operations
■ Maintenance ............................................... 42
Cleaning..................................................... 42
Image Quality
Adjustments
Appendix
Configuration
Menu
When the (warning) indicator is lit or
flashing ...............................................................35
• When the (operation) indicator is lit or
flashing ...............................................................36
• Problems relating to images................................. 37
• Problems when projection starts .......................... 41
• Problems with the remote control ........................ 41
Troubleshooting
•
When the indicators provide no help.......... 36
Appendix
■ Problem Solving ........................................ 35
Reading the indicators ............................... 35
Installing the
Projector
Troubleshooting
3
Features of the Projector
Image appearance can be selected to match the
projection environment (Color Mode)
The optimum images for the location can be projected simply by selecting the desired colour mode from the
following seven preset modes.
If "Natural", "Theatre", "Theatre Black 1", "Theatre Black 2" or "sRGB " is selected, the Epson Cinema
Filter effect is applied automatically to increase the contrast and to make skin tones appear with more natural
tints.
p.18
Dynamic
sRGB
Living Room
Color
Mode
Theatre Black1
Theatre Black2
Natural
Theatre
Sophisticated colour adjustment
In addition to the "Color Mode", the absolute colour temperature and skin tones can be adjusted by simple
procedures to render the picture even more to your own liking. Further, you can adjust gamma, the offset and
gain for RGB colours, and the hue and saturation of RGBCMY colours, to create colours that match the image.
p.20
4
Features of the Projector
Equipped with a wideangle lens shift function
The lens shift function allows the position of the
projected images to be adjusted vertically and
horizontally without distorting the images.
This can allow the projector to be set up with greater
freedom, even if it is suspended from a ceiling or at
an angle to the screen.
p.16
Equipped with 1.5x short
throw zoom lens
For zoom adjustment, 1.5x short throw zoom lens is provided.
Images can be projected onto an 100" screen (16:9 screen
only) even at a distance of approximately 3 m (10 ft.).
p.10
Advanced image quality adjustment functions
Advanced image quality adjustment functions such as "Auto Iris" and "Sharpness (Advanced)" can be used to
enjoy even sharper images. With the Auto Iris function turned on, the amount of light can be automatically
adjusted to match the images being projected, to create images with depth and perspective. The Sharpness function
is used to adjust not only the entire image, but also to emphasize specific regions, such as hair and clothing.
p.23
A variety of image setting functions
Some of the other many functions that are available are as follows.
EPSON Super White is used to prevent overexposure that can result in images that are too bright.
p.30
A progressive conversion that lets you obtain ideal results both for images with large amounts of movement
and for still images.
p.30
An aspect function that allows images to be viewed in wide-screen format.
p.18
Memory functions that allow adjustment results to be stored and later retrieved easily using the remote control.
p.24
Lock settings that can be used to lock the projector's control panel after adjustments have been made so that
they cannot be changed by mistake, or to prevent children from accidentally turning on the power and looking
into the lens.
p.31
5
Part Names and Functions
Front / Top
• Horizontal lens adjustment dial
p.16
Moves the lens horizontally.
• Control panel
• Vertical lens adjustment
See below
dial
p.16
Moves the lens vertically.
• Remote control light-
• Zoom ring
receiving area
p.13
p.16
Adjusts the image size.
Receives signals from the
remote control.
• Focus ring
• Air exhaust vent
p.16
Adjusts the image focus.
Do not touch the exhaust vent
immediately after projecting, or
while projecting, since it
becomes hot.
• Lens cover
• Front adjustable feet
Attach when not using the
projector to prevent the lens
from becoming dirty or
damaged.
p.17
Extend to adjust the projection angle so that the
projector is horizontal when placed on a desk top.
Control panel
Buttons with no explanation function in the same way as the corresponding buttons on the remote
control. Refer to "Remote control" for further details on these buttons.
• Source button
• Menu button
p.15
p.34
Selects the image source.
• Power button
• Esc button
p.14
p.18, 20, 24, 34
Turns the projector power
on or off.
•
•
(Operation) indicator
p.35
Flashes or lights in different colours to indicate the operating
status of the projector.
(Warning) indicator
• Aspect button
p.18
p.35
Flashes or lights in different colours to indicate problems
with the projector.
• Select/Line menu button
p.18, 24, 34
6
•
/
/
buttons
p.17, 18, 20, 24, 34
Used as up/down buttons to select items in
menus and select menus.
If the menus are not displayed, correct the
keystone distortion.
•
buttons
p.20, 34
Used as right/left buttons to
select adjustment values in
menus.
Part Names and Functions
Remote control
• Remote control lightemitting area
• Indicator
p.13
Outputs remote control signals.
Illuminates when remote control
signals are being output.
• On/Off buttons
p.14
Turns the projector power on/off.
• Color Mode button
• Memory button
p.24
Retrieves stored memories.
p.18
Selects the colour mode.
• Aspect
button
p.18
Selects the aspect.
• Menu button
p.34
Displays the full-screen
configuration menus.
•
• Esc button
p.18, 20, 24, 34
button
p.18, 20, 22, 24, 34
Pressing [Esc] while viewing a
menu displays the previous menu.
Press to select menu items and
adjustment values and to adjust the
zoom and focus.
• Select/Line menu button
p.18, 24, 34
Displays the line menu.
When viewing a menu, press this
button to select the menu item and
proceed to the next display.
• Gamma button
Source buttons
p.15
• HDMI button
• InputB button
• S-Video button
• Video button
Changes to the image from the
projector's selected port.
• D4/scart button
• InputA button
Changes to the image from the
projector's selected port.
You can select the input signal to
match the equipment that is
connected to the selected port.
p.20
Adjusts the gamma values.
• Color Temp. button
p.20
Adjusts the absolute colour
temperature.
• Pattern button
p.17
Selects a test pattern.
•
(Illumination) button
All buttons on the remote control illuminate when this button is pressed.
The button illumination switches off automatically after about 10 seconds
have passed.
• Contrast button
p.28
Adjusts contrast .
• S.Tone (Skin Tone)
button
p.20
Adjusts the skin tones of people
who appear in the images.
• Blank button
The projected images switch off
and on each time this button is
pressed.
7
Part Names and Functions
Rear
• [InputA] port
• [SCART] input port
p.12
Connects to the component video
of other video equipment.
p.12
Connects to the SCART ports of
other video equipment using the
D4 SCART adaptor that is
packed with the projector.
• [InputB] port
(YCbCr or YPbPr ) ports
p.12
• [HDMI
] input port
p.12
Connects to video equipment or a
computer that is HDMIcompatible.
Connects to the RGB
port of a computer.
• [Trigger out] port
• Remote control
When the projector power
is turned on, a 12 V DC
signal is output from this port.
When the projector's power is
turned off or a problem with
operation occurs, the output
becomes 0 V to send the
projector's power ON/OFF
status to an external device.
light-receiving
area
p.13
Receives signals
from the remote
control.
• Security lock
p.53
• [Video] input port
p.12
• Main power switch
Connects to general video ports of
other video equipment.
• [S-Video] input port
p.14
• Power inlet
p.12
Inputs an S-Video signal to the
projector from other video equipment.
p.14
Connects the power cable.
• [RS-232C] port
Connects the projector to a computer
using an RS-232C cable. This port is
for control use and should not be used
by the customer.
Base
• Suspension bracket fixing points (4 points)
p.46
Install the optional ceiling mount here when suspending the projector from a ceiling.
• Lamp cover
p.44
Open this cover when replacing the lamp
inside.
8
• Air filter (air intake vent)
p.42, 44
Prevents dust and other foreign particles
from being drawn into the projector.
It should be cleaned periodically.
Appearance
Centre of projector
Centre of lens
131.5
124
143
66*1
19
110
*2
406
*1 Distance from centre of lens to suspension bracket fixing point
(Lens shift amount: Max. 8.6 mm vertically)
*2 Distance from centre of lens to centre of projector
(Lens shift amount: Max. 7.7 mm horizontally)
Centre of lens
300
52.8
76.3
309
160
4-M4×8
Units:mm
9
Setting up
Adjusting the projection size
The size of the projected image is basically determined by the distance from the projector's lens
to the screen.
Lens shift
Top
Be sure to read the separate
Safety Instructions/World-Wide
Warranty Terms booklet before
installing the projector.
Do not stand this projector upright.
This may damage your projector.
Offset
Centre of lens
Adjusting the projection size
Screen
Offset
Lens shift
Bottom
Projection distance
The height from the centre of the lens to the bottom of the
screen will vary depending on the lens shift setting.
While referring to the table below, position the projector so that the images are projected onto the
screen at the optimum size.
The values should be used as a guide for setting up the projector.
Units: cm (in)
Units: cm (ft.) Units: cm (in.)
Units: cm (in)
Units: cm (ft.) Units: cm (in.)
Projection distance
16:9 screen size
Shortest
(Wide)
Longest
(Tele)
Offset
19 (7.4)
30"
40"
60"
80"
66×37 (26×15)
89×50 (35×20)
130×75 (51×28)
180×100 (71×39)
100"
220×120 (87×47)
270×150 (106×59)
330×190 (130×75)
456-681 (15.0-22.3)
93 (36.8)
200" 440×250 (173×98)
300" 660×370 (260×146)
609-909 (20.0-29.8)
916-1365 (30.1-44.8)
125 (49.0)
120"
150"
88-133 (2.9-4.4)
118-179 (3.9-5.9)
180-270 (5.9-8.9)
37 (14.7)
241-361 (7.9-11.8)
50 (19.6)
303-452 (9.9-14.8)
364-544 (11.9-17.8)
62 (24.5)
75 (29.4)
25 (9.8)
187 (73.5)
Projection distance
4:3 screen size
30"
40"
60"
80"
Shortest
(Wide)
61×46 (24×18)
81×61 (32×24)
120×90 (47×35)
160×120 (63×47)
107-163 (3.5-5.3)
145-219 (4.8-7.2)
220-330 (7.2-10.8)
295-442 (9.7-14.5)
100"
200×150 (79×59)
120" 240×180 (94×71)
150" 300×230 (118×91)
200" 410×300 (161×118)
300" 610×460 (240×181)
Longest
(Tele)
Offset
23 (9.0)
30 (12.0)
46 (18.0)
61 (24.0)
370-554 (12.1-18.2)
445-665 (14.6-21.8)
76 (30.0)
91 (36.0)
558-833 (18.3-27.3)
746-1112 (24.5-36.5)
1121-1671 (36.8-54.8)
114 (45.0)
152 (60.0)
229 (90.0)
Lens shift adjustment
The lens shift dials can be used to position the image and is especially useful when using the projector in the
following locations.
p.16
Hanging from the ceiling
A screen in a high location
Projector situated to the side so that the screen can be viewed sitting right in front of it
Projector situated on a shelf, etc.
When positioning an image using the lens shift dial, hardly any deterioration of the image occurs because the lens
shift correction is adjusted optically. However, for optimal image quality the lens shift function should not be used.
10
Setting up
When projecting from directly in front
When projecting from the side of
the screen
When projecting from a celling
* Even if projection will be from the screen
side, set up the screen and projector so that
they are parallel.
Installing the Projector
Projection methods
* When suspending the projector from a ceiling,
change the configuration menu settings.
p.33
Configuration menu
Settings
TIP
Projection
Front
Front/Ceiling
Avoid setting the projector up in a place which is very dusty or humid, or where there will
be cigarette or other smoke, especially oily smoke.
Clean the air filter at least once every 3 months.
Clean the air filter more frequently if using the projector in a dusty environment.
When installing against a wall, leave a space of 20 cm (7.9 in.) or more between the
projector and the wall.
A special method of installation is required in order to suspend the projector from the
ceiling. Please contact your dealer if you would like to use this installation method.
11
Connecting Image Sources
• Turn the power off for both the projector and the signal source before connecting them.
If the power for either device is on at the time of connection, damage may result.
• Check the shapes of the cable connectors and the device ports before making the
connections. If you try to force a connector to fit a device port with a different shape or
number of terminals, a malfunction or damage to the connector or port may result.
Computer
Video equipment (VHS VCR, DVD player, game console, etc.)
*Port names may vary depending on the equipment being connected.
S-Video
Video
S-Video cable
(commerciallyavailable)
RCA video cable
(commerciallyavailable)
Component output
SCART*
1
SCART cable
(commerciallyavailable)
+
D4 SCART
adapter*2
Component
video cable
(commerciallyavailable)
HDMI
Mini D-Sub
15-pin
HDMI cable
(commerciallyavailable)
Computer cable
(commerciallyavailable)
(accessory)
Mini D-Sub
15-pin
*1 If a DVD has been connected using a D4 SCART adapter, change the "D4/SCART" setting in the "Input Signal"
to "SCART".
"Selecting the image source" p.15
*2 Some regions may not have the D4 SCART adapter included as an accessory.
TIP
12
• Some signal sources may have specially-shaped ports. In such cases, use the
accessory or optional cables that are supplied with the signal source to make the
connections.
• The cable that should be used to connect video equipment to the projector will depend
on the type of video signal that the equipment outputs. Some kinds of video equipment
output several different types of video signal. The image quality ranking of the video
signal types is generally held to be as follows, in descending order of quality:
Digital component video [HDMI ] > Analog component video [D4] [InputA] >
S-Video [S-Video] > Composite video [Video]
You should refer to the documentation provided with the video equipment being used to
check what types of video signal formats the equipment can output. The composite
video format is sometimes simply called "video output".
Preparing the Remote Control
Inserting batteries into the remote control
The remote control is not supplied with batteries already inserted. Insert the accessory batteries
before using the remote control.
Remove the battery cover.
Install the battery cover.
Insert the tab.
Press down until the battery
cover clicks into place.
Installing the Projector
While pressing the knob, lift up.
Insert the batteries.
Check the (+) and (-)
indications inside the
battery compartment and
insert the batteries so that
they face correctly.
TIP
If delays in the responsiveness of the remote control occur or if it does not operate
after it has been used for some time, it probably means that the batteries are
becoming flat. If this happens, replace the batteries with two new batteries. Use two
new AA batteries as replacement batteries.
Using the remote control
Operating range (horizontal)
Remote control light-receiving area
Operating distance
Approx.10m
Approx.30
Approx.30
Approx.30
Approx.30
Remote control
light-emitting area
Operating range (vertical)
Operating distance
Approx.10m
Operating distance
Approx.10m
Approx.30
Approx.30
Approx.30
Approx.30
13
Projecting Images
Turning the power on and projecting images
Before using the
projector, make sure you
remove the protective
pad attached to the lens.
Remote Control
Control Panel
Turning the power on and projecting
ON
images
If there is a problem with projection even though the projector is set up and connected correctly,
refer to
p.15, 35.
TIP
If you set the "Direct Power On" to "On", the power of the unit will turn ON when
the main power switch is turned ON, without having to press the power button of
the remote control or the projector's control panel.
The projector is equipped with a "Child Lock" function that prevents young
children from accidentally turning the power on and looking into the lens, and
also an "Operation Lock" function that prevents mis-operations.
p.31
When using above an altitude of about 1500 m, make sure you set the "High
Altitude Mode" to "On".
p.32
This projector is equipped with an automatic
adjustment function that automatically optimizes it
when a computer input signal is switched.
If a laptop computer or a computer with a LCD
screen has been connected to the projector, you
may need to use keyboard or function settings to
change the output destination. While holding down
the
key, press
(the key with a symbol such
as
/
on it). After the selection is made,
projection will soon start.
Computer documentation
14
Example of output selection
NEC
Panasonic
SOTEC
HP
Toshiba
IBM
SONY
DELL
Fujitsu
Macintosh
Set mirror setting or
display detection.
Depending on OS, you can
change the output
selection by pressing
.
Projecting Images
When the expected images are not projected
If more than one signal source has been connected, or if no images are projected, use the remote control or the
projector's control panel buttons to select the signal source. For video devices, press the [Play] button on the video
equipment first, then select the signal source.
Using the remote control
Using the control panel
When the expected images are not
projected
Turning the power off
When you press , the menu is displayed.
Use or to select the signal source.
Press
to accept.
When projecting an image from the [Input A] port
The default setting is set to "Auto" to select appropriate signals automatically. However, if the colours appear unnatural,
switch the image signal to match the equipment.
Using the remote control
Using the control panel
While projecting an image from equipment
connected to the [InputA] port, press
to display the menu.
While projecting an image from equipment
connected to the [InputA] port, select "InputA"
and confirm to display the menu.
Basic Operations
Press the button that has the name of the port on it that
the desired signal source is connected to.
Use
or
to select the correct signal to
match the equipment.
Press
or
to accept.
Turning the power off
Turn the power off for the signal sources
that are connected to the projector.
Press
on the remote control or
on
the projector's control panel. If you press
on the projector's control panel, the
following message will be displayed.
Press
again to continue.
When the projector has cooled down (takes
about 30 seconds), turn off the main power
switch.
Simply pressing
or
electricity consumption.
does not stop
Attach the lens cover.
15
Adjusting the Projection Screen
Focus adjustment
Turn the focus ring to adjust the
focus.
Fine adjustments to image size
(Zoom adjustment)
Turn the zoom ring to adjust the size of the
projected image.
Wide
Tele
Projection image position adjustment
(Lens shift)
Focus adjustment
Use the two lens shift dials to adjust the
image position.
If you cannot position the projector straight
in front of the screen, use the lens shift dial
so that the image is centered on the screen.
When you turn the lens shift dial and hear a
click, the lens position is almost centred.
Down
Up
Fine adjustments to image size (Zoom
Left
adjustment)
Right
Projection image position adjustment
shift)
H
shift (Lens
the image by
100% in the
You can
vertical direction, and 50% in the horizontal
direction. However, you cannot shift the
image to these vertical and horizontal limits
simultaneously.
Ex) When the image is shifted horizontally
by the full amount, it cannot be shifted
vertically.
And when the image is shifted
vertically by the full amount, it cannot
be shifted horizontally by more than
11% of its width.
When transporting the
projector, make sure to turn
the lens position down by the
full amount. Otherwise the lens
shift function may be
damaged.
16
V
Standard
projection position
(centre position for
lens shift)
Range that the picture can be shifted
from the standard projection position
Adjusting the Projection Screen
Correcting projector tilt
If the projected images are tilted horizontally, use the front adjustable feet to adjust the projector so that it is
horizontal.
Extend
Retract
Extend
Retract
When you wish to adjust the projection above or below the range of lens shift adjustment set the projector at an
angle.
When the projector is angled, the projected image may distort into a trapezoid. In such cases, press
( ) ( )
on the control panel to adjust the images.
However, the image quality will decrease compared to if the lens shift function is used. When the lens is shifted to
the left or right, complete keystone correction is not possible. When making keystone corrections set the lens at the
centre left to right.
Keystone distortion can be corrected within a maximum vertical angle of approximately 15˚.
Correcting projector tilt
TIP
You can also make adjustments from the configuration menu.
p.31
To reset the correction value, press and hold down
with
pressed down for at least 1
second on the control panel.
Correcting keystone distortion
(Keystone)
Displaying a Displaying
test pattern
Basic Operations
Correcting keystone distortion (Keystone)
a test pattern
You can project a test pattern at times such as when setting up the projector in order to correct keystone correction
and to make line menu adjustments.
You can also adjust the zoom and focus using the test pattern.
If
on the remote control is pressed, the pattern menu appears.
Display Position
This can be used to check
that the projector is not tilted
but rather set up parallel to
the screen.
Gray Scale
Clears the test pattern
display
This is used when adjusting
brightness or when adjusting
image quality or colour tone.
The adjustment is made using
the line menu. Adjustment of
some items is not possible
when no image signals are
being input.
17
Basic Image Quality Adjustments
Selecting the colour mode
Selecting the colour mode
Press
and select the colour mode from
the menu.
Setting is also possible using the configuration
menu.
Selecting the aspect
Selecting the aspect
Press or on the remote control
or on on the projector's control
panel to select an item.
Press or to confirm the
selection.
* If you press , the menu disappears.
TIP
18
If you project an image that is
compressed, enlarged or separated
using the aspect function in public
places such as a store or hotel for
the purposes of profit-making or
public display, it may result in
infringing on the author's right that
is protected by copyright law.
Press
menu.
and select the aspect mode from the
When projecting using Auto
For 4:3 input signals
Normal
For input images recorded
in squeeze mode
Squeeze
For letterbox input signals
Zoom
*1 Not usable during computer input. Not
compatible with certain component video
signals.
*2 If Auto is not suitable, the setting will become
Normal.
Basic Image Quality Adjustments
: Ideal for using in bright
rooms.
:
Living Room Ideal for using in rooms in
which the curtains are
closed.
: Ideal for using in dark rooms.
Natural
It is recommended that you
start in this mode when
making colour adjustments.
: Ideal for using in dark rooms.
Theatre
Dynamic
Theatre
Black 1
Theatre
Black 2
sRGB
: Suitable for use in a completely
darkened room.
1: A clear tone of colour one might see in
professional monitors used when
creating DVD software.
2: A deep warm tone of colour that gives
you the feeling of enjoying a movie at
the theatre.
: If the connected signal source has an sRGB
mode, set both the projector and the connected
signal source to sRGB.
(Ideal for viewing computer images.)
Input
signal
Recommended
aspect mode
Result
Normal TV broadcasts
Images with standard
aspect ratio (4:3)
Computer images
Normal
Black bands will
appear at the left and
right of the images.
Images recorded by a
video camera or DVD
software in squeeze
mode
Letterbox images
Normal TV broadcasts
Images with standard
aspect ratio (4:3)
Squeeze
Zoom
Wide
Input signals will be
projected at the same
width as the projector's
panel resolution.
When HDTV images
are projected, the
images appear in 16:9
size.
Remarks
When 4:3 images are
projected, the images
will be elongated
horizontally.
When the image resolution is 1280 x 720 or less
and "Through" or "Squeeze Through" is selected,
the image will be projected clearer since the
resolution is retained.
Through
Squeeze
Through
To project images so that they fill the whole of the
screen, use the zoom adjustment or adjust the
distance between projector and screen.
Input signals will be
projected at the same
height as the projector's
panel resolution.
When 4:3 images are
projected, the top and
bottom of the images
will be truncated.
When images with
subtitles are projected
and the subtitles are
truncated, use the
"Zoom Caption" menu
command to adjust.
p.29
Input signals will be
projected at the same height
as the projector's panel
resolution. At this time, the
image enlargement ratio
will be smaller near the
middle of the images but
become larger towards the
left and right edges of the
images.
This is useful for when 4:3
images are projected onto a wide
screen. Because there is almost no
distortion due to enlargement in
the middle of the images, the
images appear close to what they
would be at their original size.
And because both ends of the
images are enlarged, movement at
the edges of the images appears
faster and gives an impression of
greater speed, making it ideal for
viewing sporting events.
Image Quality Adjustments
When you select the colour mode indicated with
, the Epson Cinema Filter will be applied
automatically to increase the contrast and makes skin tones more natural.
*"Wide" cannot be selected if
keystone correction has been
carried out.
19
Advanced Colour Adjustments
If you would like to create your own images with settings adjusted the way you want them, you can
adjust "Skin Tone", "Abs. Color Temp.", "RGB/RGBCMY" and/or "Gamma" in the "Color
Adjustment" sub-menu of the "Picture" menu. (When "sRGB " is not selected in Color Mode.)
The adjustment values can be stored in the memory so that you can retrieve them and apply them to the
projected images at any time. (
p.24)
"Skin Tone", "Abs.Color Temp." and "Gamma" are adjusted using the respective remote control
buttons.
Skin tone adjustment
Skin tone adjustment
Absolute colour temperature
adjustment
Press
Gamma adjustment
Absolute colour
temperature adjustment
on the remote control or
on the projector's control
panel to make the adjustment.
* If you press
, the menu disappears.
Gamma adjustment
Adjusting from the gamma
correction values
From among the gamma correction values [2.0],
[2.1], [2.2], [2.3], [2.4], select one that suits the
connected equipment, or one of your own liking,
using
or
, and press
or
to confirm
the selection.
20
Differences between equipment may result in a
slight variation in the colouring when images are
projected, and you may want to adjust this.
(Projection will stop temporarily during such
adjustment.) There are two methods of doing so.
One is to select one of the gamma correction values
[2.0], [2.1], [2.2], [2.3], [2.4]. The other is
customized adjustment, which is done with
reference to the projected image or a gamma graph.
The gamma graph's horizontal axis represents the
input signal level and its vertical axis the output
signal level.
Observe the gamma graph to check the result of the
adjustment.
Lower values will increase the contrast of the dark
portions but will tend to blur the bright portions.
This is indicated by bulging in the upper portion in
the gamma graph.
Higher values will darken the bright portions. This
is indicated by bulging in the lower portion in the
gamma graph.
Advanced Colour Adjustments
You can adjust the overall tint of images.
If you select a higher value, images appear bluish, and if you select a lower value, images appear reddish.
The absolute colour temperature can be set to one of 12 settings within the range of 5000K to 10000K.
Customized
("Adjust it from the image")
Use
or
to select first "Customized",
then "Adjust it from the image". Press
or
to confirm the selection each time.
A gamma icon will appear in the projected image.
(Keystone correction will be temporarily
cancelled while the gamma icon is displayed.)
Use
or
to move the
gamma icon to the place where you want to
adjust the brightness, and press
or
to
confirm the selection. The place selected and
the regions of the same brightness will flash,
and a gamma graph will appear. Press or
again to reconfirm. A screen for adjusting the
tone will appear.
Use
or
to make the adjustment,
and press
or
to confirm it. Press
to
go back and do it again.
Customized
("Adjust it from the graph")
Use
or
to select first "Customized",
then "Adjust it from the graph". Press
or
to confirm the selection each time.
A gamma adjustment graph will appear.
Image Quality Adjustments
This can be used to adjust the skin tones for images of people.
The Epson Cinema Filter effect that is automatically applied to images when a "Color Mode" setting is
made creates natural-looking skin tones. If you would like to further enhance skin tones, use this "Skin
Tone" setting to make the adjustment.
If set to the + side, the colours become greenish, and if set to the – side, the colours become reddish.
Use
or
to select the point where
you want to adjust the tone brightness, and press
or
to confirm the selection. A screen for
adjusting the tone will appear.
Use
and press
or
or
to make the adjustment,
to confirm it.
21
Advanced Colour Adjustments
RGB adjustment (Offset, Gain)
Press
and then select "Picture" "Color Adjustment" - "RGB/RGBCMY" "RGB" in that order and confirm the
selection.
The image brightness can be adjusted by adjusting
the individual R (red), G (green) and B (blue)
components of the dark areas (offset) and bright
areas (gain).
RGB adjustment (Offset, Gain)
Hue and saturation
Offset adjustment
If you would like dark areas to appear more clearly,
change the setting to the + (right) side. If you
change it to the - (left) side, the whole image will
become sharper, but the contrast in dark areas
will become poorer.
Use
or
to select a menu
item, and use
or
to
make adjustments.
Press
to exit the menu.
Gain
If you would like bright areas to appear more
clearly, change the setting to the – (left) side. If
you change it to the + (right) side, bright areas will
become whiter, but the contrast will become
poorer.
Hue and saturation adjustment
Press
and then select "Picture" "Color Adjustment" - "RGB/RGBCMY" "RGBCMY" in that order and confirm
the selection.
Press
to exit the menu.
The hue and saturation for each of the red (R),
green (G), blue (B), cyan (C), magenta (M) and
yellow (Y) colour components can be adjusted.
Hue
Press
or
to select a colour and
press
or
to confirm. Select either
hue or saturation and use
or
to adjust.
To adjust another colour, press or select
"Return".
22
Adjusts the overall colouration from blues to greens
to reds.
Saturation
Adjusts the overall vividness of the images.
Examining Image Quality Further
In addition to colour adjustments, adjustments to advanced sharpness and the amount of light from the
lamp can also be made to match the image in search of the best picture.
Sharpness (Advanced) adjustment
Press
, and then select "Picture" "Sharpness" - "Advanced".
Use
or
to select a menu
item, and use
or
to
make adjustments.
to exit the menu.
of the image.
If "High-band Enhancement" is set in the +
direction, hair and the detailed areas of clothing
will be emphasized.
If "Low-band Enhancement" is set in the +
direction, the areas emphasized by "High-band
Enhancement" will be hardly emphasized. Instead,
the rough areas of the entire subject, such as
contour and background, will be emphasized,
resulting in a sharp image.
(You can adjust "High-band Enhancement" and
"Low-band Enhancement" at the same time by
using the bar on the top in the screen.)
Setting "H-Sharpness" / "V-Sharpness" to the +
side will enhance the image sharpness in the
horizontal / vertical direction. Setting them to the side will give a soft image.
Sharpness (Advanced) adjustment
Auto Iris (automatic aperture) setting
Auto Iris (automatic aperture) setting
Press
, and then select "Picture"
- "Auto Iris".
The amount of light will be automatically adjusted
to the brightness of the image, creating a picture
with depth and perspective.
Image Quality Adjustments
Press
Adjust the resolution and contrast
Select "On".
Press
to exit the menu.
23
Viewing Images at a Preset Image Quality (Memory Function)
After menu commands such as "Color Adjustment" and "Advanced" have been used to adjust the
projected images, the adjustment values can then be saved.
In addition, the saved data can be retrieved easily, so that you can enjoy viewing images with the
adjusted settings at any time.
Saving image quality adjustments
(Save Memory)
Saving image quality adjustments
(Save Memory)
Settings that can be saved in memory
"Picture" menu
Configuration menus
p.26
Color Mode
White Level/Black Level
Input Adjustment
Brightness/Contrast
Color Saturation
Tint
Standard
Sharpness
Advanced
Color Adjustment
Abs. Color Temp.
Skin Tone
RGB / RGBCMY
Gamma
Displayed for input sources
other than computer
Retrieving image quality adjustments
(Load Memory)
Press or on the remote control
or or on the projector's control
panel to select an item.
Press or to confirm the
selection.
* If you press
24
, the menu disappears.
Retrieving image quality
adjustments (Load Memory)
Viewing Images at a Preset Image Quality (Memory Function)
This can be used to save adjusted values for all of the configuration menu items on the left.
The "Save Memory" command in the "Memory" menu is used to save the settings.
The following describes how to save settings.
Adjust the desired settings that you would like to save in memory.
Select "Save Memory" from the "Memory" menu and then press
or
.
The status of a memory area is indicated by the colour of the symbol to the left of the memory
name as follows.
Green : Memory area is in use
Grey : Memory area is not in use
Orange : Selected
In addition, if the memory has been registered, the colour mode selected when the memory was
registered is displayed on the right side.
If you select a memory area that is already in use and press
or
, the existing contents will
be erased and the current settings will be saved in their place.
To erase all memory contents, select "Reset Memory" from the "Memory" menu.
You can press
p.33
and select the desired memory name from the menu.
Image Quality Adjustments
Select a memory name from Memory1 to Memory9 to use for saving and then
press
or
.
The colour mode selected when the memory was registered is displayed on the right side.
TIP
Memory settings that have been applied to images will be retained even when the
projector's power is turned off. The same memory adjustment settings will be applied to
images that are projected the next time the projector's power is turned on.
The aspect setting retrieved from memory may not be applied to the images if they are
16:9 images or if the input signal images have a particular resolution.
25
Configuration Menu Functions
The configuration menus can be used to make a variety of adjustments and settings involving the screen,
image quality and input signals.
The following two types of menu are available.
■ Full menu
All items in the configuration menu can be checked
while the settings are being made.
Top menu
Sub-menu
■ Line menu
This lets you adjust some areas of the "Picture" menu
and "Memory" menu in the configuration menu.
This menu is useful for viewing the effects of
adjustments in the images being projected while the
adjustments are being made.
Navigation Bar
Refer to "Using the configuration menus"(
TIP
p.34) for details on menu operations.
The configuration menus can be used to turn the navigation bar on and off and to change
the colour pattern and display position.
"Settings" - "Display"- "Menu Position", "Navigation Bar", "Menu Color"
List of configuration menus
"Picture" menu
If no image signals are being input, none of the settings can be adjusted except for "Reset" and
"Auto Iris" in the "Picture" menu, or "Auto Setup" in the "Image" menu. The items displayed in the
"Picture" menu, the "Image" menu and the "Info" menu will vary depending on the type of image
signals that are being projected.
Dynamic, Living Room, Natural, Theatre,
Theatre Black 1, Theatre Black 2, sRGB
Color Mode
p.28
Input Adjustment
p.28
*
White Level/Black Level
Color Saturation
p.28
*
Brightness/Contrast
Tint
p.28
*
Sharpness
p.28
*
Standard
Advanced
Color Adjustment
p.28,29
Auto Iris
p.29
On, Off
Reset
p.29
Yes, No
Abs. Color Temp.
*
Skin Tone
*
RGB
RGB / RGBCMY
RGBCMY
Gamma
2.0, 2.1, 2.2, 2.3, 2.4
Customized
Reset
Displayed for input sources other than computer
* This is displayed in the line menu.
26
High-band Enhancement, Low-band Enhancement,
H-Sharpness, V-Sharpness
Aspect
p.29
Zoom Caption
p.29
Tracking
p.29
Sync.
p.29
Position
p.30
Advanced
p.30
Auto, Normal, Squeeze, Zoom, Through, Squeeze Through, Wide
Vertical Size
Zoom Position
EPSON Super White
Progressive
Off, Video, Film
Output Scaling
When component video signals are input: Normal, Larger
When signals from the [HDMI ] port are input: Auto, Normal, Larger
Auto Setup
p.31
On, Off
Reset
p.31
Yes, No
Setup Level
Keystone
0%, 7.5%
Normal, Expanded
DVI-Video Level
Displayed for input sources other than computer
Only displayed for Computer input
(does not appear when signals from the [HDMI] input port are being input)
p.31
ÉXÉäÅ[ÉvÉÇÅ[ÉhDirect Power On
Operation
On, Off
p.31
Sleep Mode
User's Logo
On, Off
p.32
Display
Yes, No
Off , 5min. ,10min. , 30min.
Trigger Out
On, Off
Child Lock
On, Off
Operation Lock
On, Off
High Altitude Mode
On, Off
Menu Position
Top-left, Top-center, Top-right, Center-left,
Center-right, Center, Bottom-left, Bottom-center, Bottom-right
p.32
Navigation Bar
On, Off
Color 1, Color 2
Menu Color
Message
On, Off
Display Background
Black, Blue, Logo
Startup Screen
Input Signal
Video Signal
p.33
On, Off
Auto, NTSC , NTSC4.43, PAL ,
M-PAL, N-PAL, PAL60, SECAM
Input A
Auto, YCbCr , YPbPr
D4(Auto), D4(YCbCr),
D4(YPbPr), SCART
D4/SCART
Projection
p.33
Language
p.33
p.33
Yes, No
The message text will be displayed in yellow
when it is time to replace the lamp.
Time from 0H to 10H will be displayed as 0H.
From 10H onwards, the display will be in units of 1H.
"Memory"
menu
Lamp Hours
Source
ì¸óÕâšëúìx
Input Signal
"Reset"
menu
"Info" menu
Reset
Front, Front/Ceiling, Rear, Rear/Ceiling
Resolution
Refresh Rate
p.33
Memory1 to Memory9
Load Memory
p.33
Memory1 to Memory9
Reset Memory
p.33
Yes, No
Reset All
p.34
Yes, No
Reset Lamp Hours
p.34
Yes, No
Only displayed for composite video/S-Video input
Only displayed for component video/RGB-Video/Computer input
Only displayed for Computer input
Sync Info
Video Signal
Save Memory *
Configuration Menu
"Settings" menu
"Image" menu
Configuration Menu Functions
* This is displayed in the line menu.
The "Info" menu is only used to display the projector status.
27
Configuration Menu Functions
"Picture" menu
Displayed for input sources other than computer
Only displayed for Computer input
(does not appear when signals from the[HDMI] input port are being input)
Color Mode*1
Seven different settings can be selected for the Color Mode, to match the images being projected or the
projection environment.
p.18
Input Adjustment *2
These settings can be adjusted if the output level from the connected equipment is weak and the images
appear dark. The two settings cannot be made simultaneously. You can only select one of them to be
adjusted.
White Level/Black Level
These adjust the dark and light areas of images
• White Level: Adjusts the brightness of bright shades without changing the black level.
When the setting is changed to the - side, bright areas become clearer.
• Black Level: Adjusts the brightness of dark shades without changing the white level.
When the setting is changed to the + side, dark areas become clearer.
Brightness/Contrast
Adjusts the overall brightness of the images.
• Brightness: The brightness of the images can be adjusted.
If projecting in dark rooms or onto small screens and the images appear too bright,
decrease the setting.
• Contrast: Adjusts the difference between bright and dark areas.
When the contrast is increased, images with greater modulation are obtained.
Color Saturation *2
This adjusts the colour intensity for the images.
Tint *2
(Adjustment is only possible when composite video
input.)
This adjusts the image tint.
and S-Video
signals in NTSC
format are being
Sharpness *2
This adjusts the image sharpness.
Standard
The adjustment results are applied to the entire image.
Advanced
This can be used to adjust a specific region.
p.23
Color Adjustment
“Color Adjustment” cannot be selected when the colour mode is set to “sRGB ”.
Abs. Color Temp. *2
This adjusts the overall tints of the images.
28
p.20
*1 The setting values are stored separately for each image source and signal type.
*2 The setting values are stored separately for each image source and colour mode setting.
Configuration Menu Functions
Only displayed for Computer input
(does not appear when signals from the[HDMI] input port are being input)
Skin Tone *2
This adjusts the skin tones of people who appear in the images.
p.20
RGB/RGBCMY *1
• RGB
:This lets you adjust the offset and gain for each of the R/G/B colour components.
p.22
• RGBCMY :This lets you adjust the hue and saturation for each of the R/G/B/C/M/Y colour
components.
p.22
Gamma *1
This adjusts gamma. You can select a value, or make adjustments while viewing an image or a graph.
p.20
Auto Iris *3
The amount of light is adjusted appropriately depending on images (On)/ or not adjusted (Off).
p.23
Reset
This returns all settings in the “Picture” menu to their default settings.
"Image" menu
*1
Aspect
Selects the aspect mode.
p.18
Zoom Caption *1
If "Aspect" is set to "Zoom" when viewing images with subtitles, change the setting as follows so that
the subtitles are visible. The vertical size and the display position can both be adjusted together.
Projection area
The vertical size of the image is reduced so that the
subtitles are displayed.
Use "Vertical Size" to
reduce the image size.
Zoom Position
The whole of the image is moved up so that the
subtitles are displayed.
Tracking
Subtitle section
Use "Zoom Position" to change
the display position of the image.
*1
Configuration Menu
Vertical Size
This adjusts the images if vertical stripes appear in the images.
Sync.
*1
This adjusts the images if flickering, fuzziness or interference appear in the images.
• Flickering and fuzziness may also appear in images when the brightness, contrast , sharpness and
keystone correction settings are adjusted.
• Clearer adjustments can be obtained if you adjust the "Tracking" first and then adjust the "Sync".
*1 The setting values are stored separately for each image source and signal type.
*2 The setting values are stored separately for each image source and colour mode setting.
*3 The setting values are stored separately for each colour mode setting.
29
Configuration Menu Functions
Displayed for input sources other than computer
Position *1
(Setting is not possible when signals are being input from the [HDMI ] input port.)
Use
, , and to move the display position for images.
Advanced
EPSON Super White *1
(Setting is only possible when Color Mode is "Natural", "Theatre", "Theatre Black 1", or "Theatre Black
2", and composite video , S-Video , component video , or RGB video signals are being input.)
If bright white areas of images such as clouds and T-shirts on the beach in summer appear uneven and
overexposed, set to "On". When set to "On", the "DVI-Video Level" setting will be ignored.
Progressive *1
(Setting is only possible when composite video, S-Video, component video or 525i and 625i RGB video
signals are being input.)
Interlace (i) signals are converted to progressive (p) signals using a method appropriate for the image.
• Off :This is ideal for using when viewing images with a large amount of movement.
• Video :This is ideal for general video images.
• Film :When the input source is a film, the image equivalent with its original source will be projected.
Output Scaling *1
(Setting is not possible when composite video, S-Video, or computer signals are being input.)
This changes the display area (the part of projected images).
• Normal (92% display) : Input signals are projected at the normal image size. TV images are
displayed at 92% size.
• Larger (100% display) : The areas at the top, bottom and sides of images that cannot normally be seen
are inserted and projected. Interference may occur at the top or bottom of the
images depending on the image signal. In such cases, try to adjust the display
position ("Position").
p.30
• Auto
: Displayed when the signals from [HDMI ] input port are being input. Signals
are automatically projected at 100% or 92% size depending on the input
signals. (Not displayed when the equipment's DVI port is connected to the
projector's [HDMI] input port.)
Setup Level *1
(Setting is only possible when composite video or S-Video signals in NTSC format are being input or
when component video or RGB video is selected as an image source. Setting is not possible when
computer signals are being input.)
If using products designed for destinations such as South Korea that have different black level (setup
level) settings, use this function to obtain correct images. Check the specifications of the connected
equipment when changing this setting.
DVI-Video Level *1
(Setting is only possible when RGB video is being input from the [HDMI] input port and "EPSON Super
White" is set to "Off".)
If the projector's [HDMI] input port is connected to the DVI port of a DVD player or similar equipment
using an HDMI/DVI cable, set the video level for the projector to match the video level that has been set
at the DVD player. The setting at the DVD player can be either Normal or Expand.
30
*1 The setting values are stored separately for each image source and signal type.
Configuration Menu Functions
Auto Setup
This sets automatic adjustment to on or off in order to set whether the projector automatically adjusts
images to their optimum condition when the input signal is changed. The three automatically adjusted
items are "Tracking ", "Position" and "Sync ."
Reset
All the adjustment values on the "Image" menu, except "Aspect ", are returned to their default values.
"Settings" menu
Keystone
(If the aspect mode is set to "Wide", keystone correction cannot be set.)
This is used to correct keystone distortion in images. The same correction can be carried out using the
projector's control panel.
p.17
Operation
Direct Power On
When the main power switch is turned on, you can set for projection to start (On) / not start (Off) without
pressing
or .
When set to "On" with the power left on, be aware that sudden surges of electricity that may occur when
the power comes back on after a power outage may cause the projector to turn on.
Sleep Mode
The projector is equipped with a power-saving function that causes the power to turn off automatically
and the projector to switch to standby if no signal is input to the projector for a continuous length of time.
The length of time before the power-saving function operates can be selected from four available settings.
If "Off" is selected, the power-saving function will not operate.
If you press
while the projector is in standby mode, projection will start again.
This turns the trigger function on and off to determine whether the projector's power on/off status and
problems with projector operation are communicated to an external device.
If you change the setting, the new setting will take effect after the power has been turned off and the cooldown period is complete.
Child Lock
This locks the power on function of the
button on the projector's control panel, so that a child cannot
accidentally turn the projector's power on and look into the projector's lens. When the lock is applied, the
power will only turn on if
is pressed down for about 3 seconds.
can be used to turn off the power,
and the remote control will continue to operate as normal.
If you change the setting, the new setting will take effect after the power has been turned off and the cooldown period is complete.
When the "Direct Power On" is set to "On", be aware that projection starts immediately as main power
switch is turned on.
Configuration Menu
Trigger Out
Operation Lock
If this is set to "On", you can't operate the projector's control panel buttons and a icon appears on the
screen when a button is pressed. To cancel, press and hold
on the projector's control panel for about
seven seconds or more.
If you change the setting, the new setting will take effect after exiting the configuration menu.
31
Configuration Menu Functions
High Altitude Mode
A fan is set at a certain speed of rotation so as to bring down internal temperature.
When using above an altitude of about 1500m, set to "On".
User’s Logo
You can record your favorite image as a user's logo.
The logo will be projected when projection starts and when using the blank function. When a user's logo
is recorded, the previous user's logo will be erased. Follow the instructions on the screen to record a user's
logo.
Selection
frame
Record
Move the selection frame so that
the area of the image to be
recorded is inside the frame.
Select the display ratio.
• The image will be displayed in dot format while the selection frame is displayed, therefore the display
size may change.
• The size of the recorded image is 400 × 300 dots.
• Once a user's logo has been recorded, you cannot return the logo to the default setting.
• To use the recorded user's logo, set "Display Background" to "Logo".
Display
Menu Position
Press
,
,
and
to specify the position for the menus to be displayed.
Navigation Bar
This sets whether the navigation bar for the configuration menus is displayed (On) or not displayed (Off).
Menu Color
Selects the colour for the main configuration menu and the navigation bar.
• Color 1:Black
• Color 2:Purple
Message
This sets whether the following message displays appear (On) or don't appear (Off).
• Image signal, colour mode, aspect , test pattern and item name when memory settings are retrieved
• Messages such as when no image signals are being input, when an incompatible signal is input, and
when the internal temperature rises
Display Background
Displays a menu for selecting the screen status for when using the blank function or when no image
signal is input.
Startup Screen
This sets whether the start-up screen (the image that is projected when projection starts) is displayed (On)
or not displayed (Off).
If you change the setting, the new setting will take effect after the power has been turned off and the cooldown period is complete.
32
Configuration Menu Functions
Input Signal
Video Signal
Sets the signal format in accordance with the video equipment that is connected to the [Video] or [SVideo] input port. If set to "Auto", the video signal format is set automatically.
If there is a lot of interference in the image, or if a problem such as no image being projected occurs even
though "Auto" has been selected, select the correct signal format manually.
InputA
Change this setting depending on the type of signal that is being output from the video equipment that is
connected to the [InputA] port.
If "Auto" is selected, appropriate signal is automatically set. If colours appear unnatural even though
"Auto" is selected, select appropriate signal name in the menu.
D4/SCART
This sets the signal format in accordance with the signals being output from video equipment that is
connected to the [SCART] port (in Europe) or [D4] port (in Japan).
Projection
This should be set in accordance with the method used to set up the projector.
• Front
: Select when the projector is set up in front of the screen.
• Front/Ceiling : Select when the projector is set up in front of the screen and suspended from a ceiling.
• Rear
: Select when the projector is set up behind the screen.
• Rear/Ceiling : Select when the projector is set up behind the screen and suspended from a ceiling.
Language
This sets the display language for messages and menus.
Reset
"Memory" menu
Save Memory
This can be used to save "Picture" menu and the "Image" menu settings.
p.24
Load Memory
This retrieves settings previously saved using "Save Memory"
p.24
Configuration Menu
Adjustment values for the "Settings" menu functions are returned to their default settings, except for the
"High Altitude Mode", "Input A", "D4/SCART", "Projection", and "Language".
Reset Memory
This resets (erases) all settings that have been made using the "Save Memory".
33
Configuration Menu Functions
"Reset" menu
Reset All
This resets all configuration menu settings to their default settings. The "Save Memory", "InputA", "D4/
SCART" and "Language" settings will not be reset. The "Save Memory" is reset by "Reset Memory".
Reset Lamp Hours
This initialises the lamp operating time. When this command is selected, the cumulative operating time
for the lamp is cleared and returned to the default setting.
Using the configuration menus
Displaying a menu
Full menu: Press
.
Line menu: Press
or
.
Selecting a menu item
Use
or
to select a menu item, then press
.
Changing settings
Example:
Use
or
to adjust values.
(green): Current setting value
(orange): Currently-selected item
Use
to select an item, then press
.
If you press
when an item with
will be displayed.
next to it is selected, the selection screen for that item
To return to a previous display, press
. Alternatively, select [Return] and then press
When setting is complete
Press
34
or
.
.
Problem Solving
Reading the indicators
The projector is provided with the following two indicators which notify you of the operating status of the
projector.
The following tables show what the indicators mean
and how to remedy the problems that they indicate.
* If all indicators are switched off, check that the
power cable is connected correctly and that the
main power switch is on.
When the
(operation) indicator
(warning) indicator
(warning) indicator is lit or flashing warning/problem
: Lit
Red
(Lit/off for
1 sec)
Red
(Lit/off for
0.5 sec)
: Flashing
Internal problem / Fan problem / Sensor problem / Cinema filter problem /
Auto iris problem
Disconnect the power cable from the electrical outlet. Then contact your dealer or
the nearest address provided in the "International Warranty Conditions" section of
the Safety Instructions/World-Wide Warranty Terms booklet.
Lamp problem / Lamp on error / Lamp cover open error
Check if the lamp is broken.
p.44
If the problem is still not solved after the lamp is
replaced, stop using the projector and disconnect the
power cable from the electrical outlet. Then contact your
dealer or the nearest address provided in the
"International Warranty Conditions" section of the Safety
Instructions/World Wide Warranty Terms booklet.
If the lamp is
not broken
Replace the lamp
and then turn the
power on.
If the lamp is
broken
Contact your local dealer for further advice.
Red
High internal temperature
(overheating)
The lamp will switch off
automatically and projection will
stop. Wait for approximately 5
minutes. When the cooling fan
stops, turn off the main power
switch at the rear of the projector.
Orange
High-speed cooling in
progress
You can continue using the
projector, but if the temperature
rises again, it will switch off
automatically.
• If the projector is
installed against a
wall, leave a space
of 20 cm or more
between it and the
wall.
• Clean the air filters
if they are blocked.
p.42
If the problem is not solved
when the power is turned
back on, stop using the
projector, turn off the main
power switch, and
disconnect the power
cable from the electrical
outlet. Then contact your
dealer or the nearest
address provided at
"International Warranty
Conditions" in Safety
Instructions/World-Wide
Warranty Terms booklet.
Troubleshooting
Check that the lamp and the lamp cover are securely installed.
When using above an altitude of about 1500 m, make sure you set the "High Altitude Mode" to
"On".
p.32
35
Problem Solving
When the
When the
Orange
Green
Green
(operation) indicator is lit or flashing normal
(warning) indicator is off
: Lit
: Flashing
Standby condition
If you press
Warm-up in
progress
Warm-up time is approximately 30 seconds.
Power off operations are ignored while warm-up is in progress.
Projection in
progress
Orange Cool-down
, projection will start after a brief interval.
Normal operation is in progress.
in
progress
Cool-down time is approximately 30 seconds.
After cool-down is complete, the projector goes to standby mode.
You cannot use the remote control or the projector's control panel
during cool-down.
If the main power switch at the rear of the projector is turned off before
cool-down is complete, wait for the lamp to cool down (normally about
one hour is required) before turning the power back on again.
When the indicators provide no help
If any of the following problems occur and the indicators do not offer a solution, refer to the pages
given for each problem.
Problems relating to images
● No images appear
p.37
Projection does not start, the projection area is
completely black, the projection area is
completely blue, etc.
● Moving images are not displayed
p.37
Moving images played on computer are not
displayed.
● The message "Not Supported." is
displayed p.38
● The message "No Signal." is displayed
p.38
● Images are fuzzy or out of focus
p.38
● Interference or distortion appear in
images p.39
Problems such as interference, distortion or
black & white checked patterns appear.
Problems when projection starts
● Power does not turn on
36
p.41
● Image is truncated (large) or
small p.39
Only part of the image is displayed.
● Image colours are not right
p.40
The whole image appears purplish or
greenish, images are black & white, colours
appear dull, etc.
(Computer monitors and LCD screens have
different colour reproduction performance, so
that the colours projected by the projector and
the colours appearing on the monitor may not
necessarily match, but this is not a sign of a
problem.)
● Images appear dark
p.40
● Projection stops automatically
p.41
Problems with the remote control
● The remote control does not
work p.41
Problem Solving
Problems relating to images
■ No images appear
Have you pressed the [Power]
button?
Press
panel.
Is the main power switch
turned off?
Turn on the main power switch at the rear of the projector.
Are all of the indicators
switched off?
Disconnect the power cable and then reconnect it.
p.14
Check the circuit breaker to see if power is being supplied.
Is blank mode active?
Press
Is a video signal being input?
Check that the power for the connected equipment is turned on. If
the "Message" menu command has been set to "On", messages
relating to the image signals will be displayed.
"Settings" - "Display" - "Message" p.32
Are the image signal format
settings correct?
If a composite video or S-Video signal is being inputÅ
If projection does not occur when the "Video Signal" menu
command is set to "Auto", select the signal format that matches the
signal source.
"Settings" - "Input Signal" - "Video Signal" p.33
on the remote control or
on the projector’s control
on the remote control to cancel the blank function.
If the signal source is connected to the [InputA] port
If projection does not occur when the "InputA" in the "Input
Signal" menu command is set to "Auto", set the signal format that
matches the signal that is being projected from the connected
equipment.
"Settings" - "Input Signal" - "Input A" p.33
You can also press
on the remote control to select the
format.
p.15
If the VCR or DVD equipment is connected using a D4 SCART
adapter
Press
to set the signal format to "D4/SCART".
p.15
When still no images appear and the DVD equipment is connected,
change the setting at the DVD equipment to RGB output.
Have the configuration menu
settings been made correctly?
Try resetting all of the current settings.
Were the projector and computer
connected while their power was
already turned on?
If the connection is made while the power is already turned on, the
function (Fn) key that switches the computer's video signal to
external output may not work. Turn the power for the computer that
is connected to the projector off and then back on again.
■ Moving images are not displayed
Is the computer image signal set Set the image signal to output only externally.
Computer documentation, under a title such as "External
to output simultaneously both
output" or "Connecting an external monitor"
externally and to the LCD
monitor?
Troubleshooting
When a computer is
connected
p.34
Only when projecting images
from a laptop computer or
computer with a built-in LCD
screen
37
Problem Solving
■ The message "Not Supported." is displayed
Are the image signal format
settings correct?
If a composite video or S-Video is being input
If projection does not occur when the "Video Signal" menu
command is set to "Auto", select the signal format that matches the
signal source.
"Settings" - "Input Signal" - "Video Signal" p.33
If the signal source is connected to the [InputA] port
If projection does not occur when the "InputA" in the "Input
Signal" menu command is set to "Auto", set the signal format that
matches the signal that is being projected from the connected
equipment.
"Settings" - "Input Signal" - "Input A" p.33
You can also press
, on the remote control to select the
format.
p.15
Does the mode match the
frequency and resolution of the
image signals?
Only when projecting
computer images
Use the "Resolution" menu command to check the signals being
input, and check the "List of Supported Monitor Displays" to make
sure that the signals are compatible.
"Info" - "Resolution" p.27
"List of Supported Monitor Displays" p.47
■ The message "No Signal." is displayed
Are the cables connected
correctly?
Check that all of the cables required for projection are securely
connected.
p.12
Has the correct video input port
been selected?
Press
,
,
,
or
on the remote control or
on the projector’s control panel to change the image source.
p.15
Is the power for the connected
equipment turned on?
Turn the power on for the devices.
Are the image signals being
output to the projector?
If the image signals are only being output to the computer's LCD
monitor, you need to change the output.
For some computer models, when the image signals are output
externally, they no longer appear on the LCD monitor.
Computer documentation, under a title such as "External
output" or "Connecting an external monitor"
Only when projecting
images from a laptop
computer or computer
with a built-in LCD
screen
If the connection is made while the power is already turned on, the
function [Fn] key that switches the computer's video signal to
external output may not work. Turn the power for the projector and
the computer off and then back on again.
p.14
■ Images are fuzzy or out of focus
38
Has the focus been adjusted
correctly?
Adjust the focus.
p.16
Is the lens cover still attached?
Remove the lens cover.
Is the projector at the correct
distance?
The recommended distance from the projector to the screen is
within 88-1365 cm (2.9-44.8 ft.) for a screen size of 16:9, and 1071671 cm (3.5-54.8 ft.) for a screen size of 4:3. Set up the projector
so that the projection distance is within this range.
p.10
Is the keystone adjustment
value too large?
Decrease the projection angle to reduce the amount of keystone
correction.
p.17
Problem Solving
Has condensation formed on the If the projector is suddenly taken from a cold environment to a
warm environment or if sudden ambient temperature changes
lens?
occur, condensation may form on the surface of the lens, and this
may cause the images to appear fuzzy. Set the projector up in the
room approximately one hour before it is to be used. If
condensation forms on the lens, turn the power off and wait for the
condensation to disappear.
■ Interference or distortion appear in images
Are the image signal format
settings correct?
If a composite video or S-Video is being input
If projection does not occur when the "Video Signal" menu
command is set to "Auto", select the signal format that matches the
signal source.
"Settings" - "Input Signal" - "Video Signal" p.33
If the signal source is connected to the [InputA] port
If projection does not occur when the "InputA" in the "Input
Signal" menu command is set to "Auto", set the signal format that
matches the signal that is being projected from the connected
equipment.
"Settings" - "Input Signal" - "Input A" p.33
You can also press
on the remote control to select the
format.
p.15
Are the cables connected
correctly?
Check that all of the cables required for projection are securely
connected.
p.12
Is an extension cable being
used?
If an extension cable is used, interference may increase. Try
connecting a signal amplifier.
Have the "Sync. " and
"Tracking " settings been
adjusted correctly?
The projector has an automatic adjustment function that causes the
optimum images to be projected. However, for some types of
signal, the correct adjustments may not be obtained even after
automatic adjustment is carried out. In such cases, use the
"Tracking" and "Sync." menu commands to make the adjustments.
"Image" - "Tracking", "Sync." p.29
Computer and RGB
video signals only
Has the correct resolution been
selected?
Only when projecting
computer images
Set the computer so that the signals that are output are compatible
with this projector.
"List of Supported Monitor Displays" p.47
Computer documentation
Has the correct aspect
selected?
been
Press
to select the aspect that corresponds to the input
signal.
p.18
If images with subtitles are being projected using "Zoom", use the
"Zoom Caption" menu command to adjust the images.
p.29
Has the "Position" setting been
adjusted correctly?
Use the "Position" the menu command to make the adjustment.
"Image" - "Position" p.30
Has the computer been set for
dual display?
If dual display has been activated in the Display Properties of the
computer's Control Panel, the projector will only project about half
of the image on the computer screen. To display the whole of the
image on the computer screen, turn off the dual display setting.
Computer video driver documentation
Only when projecting
computer images
Troubleshooting
■ Image is truncated (large) or small
39
Problem Solving
Has the correct resolution been
selected?
Only when projecting
computer images
Set the computer so that the signals that are output are compatible
with this projector.
"List of Supported Monitor Displays" p.47
Computer documentation
■ Image colours are not right
Are the image signal format
settings correct?
If a composite video or S-Video is being input
If projection does not occur when the "Video Signal" menu
command is set to "Auto", select the signal format that matches the
signal source.
"Settings" - "Input Signal" - "Video Signal" p.33
If the signal source is connected to the [InputA] port
If projection does not occur when the "InputA" in the "Input
Signal" menu command is set to "Auto", set the signal format that
matches the signal that is being projected from the connected
equipment.
"Settings" - "Input Signal" - "Input A" p.33
You can also press
on the remote control to select the
format.
p.15
Are the cables connected
correctly?
Check that all of the cables required for projection are securely
connected.
p.12
Has the image contrast
been adjusted correctly?
Use the "Contrast" or the "White Level" menu command to adjust the
contrast.
"Picture" - "Input Adjustment" - "Brightness/Contrast", "White
Level/Black Level" p.28
Has the colour been adjusted
correctly?
Use the "Color Adjustment" menu command to adjust the colour.
"Picture" - "Color Adjustment" p.28
Have the colour intensity and
tint been adjusted correctly?
Use the "Color Saturation" and "Tint" menu commands to adjust
the colour and tint.
"Picture" - "Color Saturation", "Tint" p.28
Only when projecting
images from a video
source
■ Images appear dark
40
Has the image brightness been
adjusted correctly?
Use the "Brightness" menu commands to make the adjustments.
"Picture" - "Input Adjustment" - "Brightness/Contrast" p.28
Has the image contrast
been adjusted correctly?
Use the "Contrast" or the "White Level" menu command to adjust the
contrast.
"Picture" - "Input Adjustment" - "Brightness/Contrast", "White
Level/Black Level" p.28
Is the lamp due for
replacement?
When the lamp is nearly due for replacement, the images will
become darker and the colour quality will become poorer. When
this happens, the lamp should be replaced with a new one.
p.44
Problem Solving
■ Projection stops automatically
Is sleep mode active?
When "Sleep Mode" has been set to On, the lamp turns off
automatically if no signal is input for about 30 minutes, and the
projector switches to standby mode. Press the
button on the
remote control or the
button on the projector's control panel to
turn the projector's power back on. To cancel the sleep mode
setting, change "Sleep Mode" menu command to "Off".
"Settings" - "Operation" - "Sleep Mode" p.31
Problems when projection starts
■ Power does not turn on
Have you pressed the [Power]
button?
Press
panel.
on the remote control or
on the projector's control
Is "Child Lock" set to "On"?
If the "Child Lock" menu command is set to "On", press
on the
projector's control panel for about 3 seconds or press
on the
remoto control to turn the power on.
"Settings" - "Operation" - "Child Lock" p.31
Is "Operation Lock" set to "On"? If the "Operation Lock" menu command is set to "On", all buttons
on the projector’s control panel are disabled. Press
on the
remote control.
"Settings" - "Operation" - "Operation Lock" p.31
Are all of the indicators
switched off?
Disconnect the power cable and then reconnect it.
p.14
Check the circuit breaker to see if power is being supplied.
Do the indicators turn off and on Turn the power off, disconnect the power cable and then reconnect
it. If this does not solve the problem, there may be a problem with
when the power cable is
the power cable. Then contact your dealer or the nearest address
touched?
provided at "International Warranty Conditions" in Safety
Instructions/World-Wide Warranty Terms booklet.
Problems with the remote control
Is the remote control lightemitting area facing towards the
remote control light-receiving
area when it is operated?
Face the remote control towards the remote control light-receiving
area.
The operating angle for the remote control is approximately ±30°
horizontally and approximately ±30° vertically.
p.13
Is the remote control too far
from the projector?
The operating range for the remote control is approximately 10m.
p.13
Is direct sunlight or strong light
from fluorescent lamps shining
onto the remote control lightreceiving area?
Set the projector up in a location where strong light will not shine
onto the remote control light-receiving area.
Are the batteries dead, or have
the batteries been inserted
correctly?
Insert new batteries, while making sure that they face correctly.
p.13
Troubleshooting
■ The remote control does not work
41
Maintenance
This section describes maintenance tasks such as cleaning the projector and replacing consumable parts.
Cleaning
You should clean the projector if it becomes dirty or if the quality of projected images starts to
deteriorate.
Be sure to read the separate Safety Instructions/World-Wide Warranty Terms booklet for details
on safe handling of the projector during cleaning.
Cleaning the air filter
If the air filter becomes blocked with dust and the message
"The projector is overheating. Make sure nothing is blocking
the air vent, and clean or replace the air filter" is displayed,
clean the air filter.
Turn the projector upside-down and use a vacuum cleaner to
clean the air filter
If the air filter becomes clogged with dust, it can result
in overheating which may cause operating problems or
reduce the operating life of the optical parts. It is
recommended that you clean the air filter about once
every three month. If using the projector in a dusty
location, the air filter should be cleaned more often.
Cleaning the projector case
Clean the projector case by wiping it gently with a soft cloth.
If the projector is particularly dirty, moisten the cloth with
water containing a small amount of neutral detergent, and
then firmly wring the cloth dry before using it to wipe the
projector case. Then wipe the case again with a soft, dry cloth.
Do not use volatile substances such as wax, alcohol or
thinner to clean the projector case. These can cause
the case to warp and make the coating finish peel off.
Cleaning the lens
To clean the lens it is preferable to use an air blower
purchased for the purpose. But alternatively you can wipe it
gently clean with a spectacle-cleaning cloth.
Do not rub the lens with harsh materials or subject the
lens to shocks, as it can easily become damaged.
42
Maintenance
Consumable replacement periods
Air filter replacement period
• If the air filter has been broken or the "Replace" message is displayed even though the
air filter has been cleaned.
Replace with an optional air filter.
Replacing the air filter p.44
Lamp replacement period
• The message "Replace the lamp." appears on the screen when projection starts.
A message will be displayed.
TIP
• The replacement warning message is set to appear after a minimum of about 1600
hours of lamp use in order to maintain the initial brightness and quality of the
projected images. The time taken for the message to appear will vary depending on
usage conditions such as Color Mode settings.
If you continue to use the lamp after this period, the possibility of the lamp breaking
becomes greater. When the lamp replacement message appears, replace the lamp
with a new one as soon as possible, even if it is still working.
• Depending on the characteristics of the lamp and on the way it has been used, the
lamp may become darker or stop working before the lamp warning message appears.
You should always have a spare lamp ready in case it is needed.
• Contact your dealer for a spare lamp.
Appendix
• The projected images get darker or start to deteriorate.
43
Maintenance
Replacing consumables
Replacing the air filter
TIP
Dispose of used air
filters properly in
accordance with
your local
regulations.
Air Filter:
Polypropylene
Press
or
to turn
the power off, wait until
the projector cools down,
and then turn off the
main power switch.
Remove the air filter
cover.
Put your finger under the
latch and pull it upward.
Replacing the lamp
If the lamp stops working
and needs to be
replaced, there is the
danger that the lamp
may already be broken.
If replacing the lamp of a
projector which has been
installed to the ceiling,
you should always
assume that the lamp is
broken and handle it with
extreme care during
removal. Furthermore,
you should stand to the
side of the projector, not
underneath it.
Press
or
to turn
the power off, wait until
the projector cools down,
and then turn off the
main power switch.
Remove the lamp cover.
* Wait until the lamp
cools down (takes
approximately 1 hour).
Securely tighten the
lamp fixing screws.
Install the lamp cover.
Resetting the lamp operating time
The lamp operating time
must always be reset after
the lamp has been replaced
with a new one.
The projector has a built-in
counter which keeps track
of the lamp operating time.
When the cumulative
operating time reaches a
certain point, it causes the
replacement warning
message to be displayed.
44
Press to turn on
the power.
Press
to display
the configuration menu.
Maintenance
Remove the old air
filter.
Insert the new air filter.
Install the air filter cover.
Loosen the lamp fixing
screws.
Remove the old lamp.
Insert the new lamp.
Pull out straight.
Make sure that it faces
the correct way.
Install the lamp and the lamp cover securely. The lamp will not turn on if
the lamp or the lamp cover is not installed correctly.
Appendix
This product includes a lamp component that contains mercury (Hg).
Please consult your state and local regurations regarding disposal or
recycling. Do not put in the trash.
Select "Reset Lamp
Hours" from the "Reset"
menu.
Select "Yes" and then
press
.
45
Optional Accessories / Consumables
The following optional accessories / consumables are available for purchase if required. This list of
optional accessories / consumables is current as of October, 2005. Details of accessories are subject to
change without notice.
Varies depending on country of purchase.
■ Optional Accessories
■ Consumables
50" Portable Screen
ELPSC06
A compact screen which can be carried easily.
(Aspect 4:3)
(1 spare lamp, 1 spare screwdriver)
Use as a replacement for spent lamps.
60" Portable Screen
80" Portable Screen
100" Portable Screen
Air Filter Set
ELPSC07
ELPSC08
ELPSC10
A portable roll-type screen. (Aspect 4:3)
80" Spring Roller Screen
ELPSC15
A roll-up screen.
(Aspect 16:9)
Screen Stand
ELPSCST01
A stand for the 80" Spring Roller Screen.
Soft Carry Case
ELPKS55
Use this case if you need to carry the projector by
hand.
VGA-HD15 PC Cable (1.8 m)
VGA-HD15 PC Cable (3 m)
VGA-HD15 PC Cable (20 m)
ELPKC02
ELPKC09
ELPKC10
(For mini D-Sub 15-pin/mini D-Sub 15-pin)
Use to connect the projector to a computer.
Ceiling Mount*
ELPMB20
(with ceiling plate)
Use when installing the projector to a ceiling.
Celling Pipe 600 (600 mm/white)*
ELPFP07
Use when installing the projector to a high ceiling or
a ceiling with veneer panels.
46
Lamp Unit
* A special method of installation is required in
order to suspend the projector from the ceiling.
Please contact the place of purchase if you would
like to use this installation method.
(1 air filter)
Use as a replacement for old air filters.
ELPLP35
ELPAF09
List of Supported Monitor Displays
Depending on the setting, the output screen resolution will change slightly.
Component Video
4:3
16:9 : Aspect
Units: Dots
Aspect mode
Signal
Resolution
SDTV (525i,
60Hz)(D1)
Normal
Squeeze
Zoom
Through
Squeeze
through
Wide
640×480
640×360 *
960×720
1280×720
1280×720
596×446
794×446
1280×760
4:3
16:9
16:9
4:3
16:9
16:9
SDTV(625i,
50Hz)
768×576
768×432 *
960×720
1280×720
1280×720
708×528
944×528
1280×760
4:3
16:9
16:9
4:3
16:9
16:9
SDTV(525p)
(D2)
640×480
640×360 *
960×720
1280×720
1280×720
596×446
794×446
1280×760
4:3
16:9
16:9
4:3
16:9
16:9
SDTV(625p)
768×576
768×432 *
960×720
1280×720
1280×720
708×528
944×528
1280×760
4:3
16:9
16:9
4:3
16:9
16:9
HDTV (750p)
16:9(D4)
1280×720
-
-
-
-
HDTV(1125i)
16:9(D3)
1920×1080
-
-
-
-
1280×720
16:9
1280×720
16:9
1176×664
16:9
-
*Letterbox signal
Composite Video /S-Video
4:3
16:9 : Aspect
Units: Dots
Aspect mode
Signal
Resolution
TV(NTSC )
TV(PAL ,
SECAM )
596×446
Squeeze
through
794×446
1280×720
4:3
16:9
16:9
1280×720
708×528
944×528
1280×720
16:9
4:3
16:9
16:9
Normal
Squeeze
Zoom
Through
640×480
640×360 *
960×720
1280×720
1280×720
4:3
16:9
16:9
768×576
768×432 *
960×720
1280×720
4:3
16:9
Wide
Appendix
*Letterbox signal
47
List of Supported Monitor Displays
Analog-RGB signals/signals input to the [HDMI ] input port
Units: Dots
Aspect
Signal
mode
Resolution
Normal
Squeeze
Zoom
Through
Squeeze
through
Wide
VGA 60
640×480
640×360 *2
960×720
1280×720
1280×720
640×480
853×480
1280×720
VESA72/75/
85, iMac*1
640×480
640×360 *2
960×720
1280×720
1280×720
640×480
853×480
1280×720
SVGA 56/60/
72/75/85,
iMac*1
800×600
800×450 *2
960×720
1280×720
1280×720
800×600
1066×600
1280×720
XGA 60/70/
75/85, iMac*1
1024×768
1024×576 *2
960×720
1280×720
1280×720
-
-
1280×720
WXGA60-1
1280×768
1280×720
1280×720
1280×720
-
-
-
WXGA60-2
1360×768
1280×720
1280×720
1280×720
-
-
-
SXGA 60
1280×1024
1280×960
960×720
1280×720
1280×720
-
-
1280×720
MAC13"
640×480
960×720
1280×720
1280×720
640×480
853×480
1280×720
MAC16"
832×624
960×720
1280×720
1280×720
832×624
1109×624
1280×720
MAC19"
1024×768
960×720
1280×720
1280×720
-
-
1280×720
SDTV (525i,
60Hz)
640×480
640×360 *2
960×720
1280×720
1280×720
640×480
853×480
1280×720
SDTV(525p)
640×480
640×360 *2
960×720
1280×720
1280×720
640×480
853×480
1280×720
SDTV(625i,
50Hz)
768×576
768×432 *2
960×720
1280×720
1280×720
768×576
1024×576
1280×720
SDTV(625p)
768×576
768×432 *2
960×720
1280×720
1280×720
768×576
1024×576
1280×720
HDTV
(750p)
1280×720
1280×720
-
-
1280×720
-
-
HDTV(1125i)
1920×1080
1280×720
-
-
-
-
-
*1 Connection is not possible if the equipment does not have a VGA output port.
*2 Letterbox signal
correspond to input signals from the [HDMI] input port.
It may be possible to project signals which are not listed in the above table. However, some functions may
be limited in that case.
48
Specifications
Product name
Home Projector EMP-TW620
*Model lineup varies depending on the country.
Dimensions
406 (W) × 124 (H) × 309 (D) mm (not including feet)
Panel size
0.7 inch wide
Display method
Polysilicon TFT active matrix
Resolution
921,600 pixels (1280 (W) × 720 (H) dots) × 3
Scanning
frequencies
Analogue
Pixel clock : 13.5 - 110 MHz
Horizontal : 15 - 92 kHz
Vertical
Digital
: 50 - 85 Hz
Pixel clock : 13.5 - 81 MHz
Horizontal : 15 - 60 kHz
Vertical
: 50 - 85 Hz
Focus adjustment
Manual
Zoom adjustment
Manual (appox. 1 : 1.5)
Lens shift
Manual (Maximums: Approx. 100% vertically, 50% horizontally)
Lamp (light source)
UHE lamp, 170 W, Model No.: ELPLP35
Power supply
100- 240VAC 50/60Hz 2.7-1.2A
Power Consumption
Operating: 245W(100-120V area), 240W(200-240V area)
Standby: 4.0W(100-120V area), 5.0W(200-240V area)
Operating altitude
0 – 2280m (0 – 7500ft.)
Operating
temperature
+5 – +35°C (No condensation)
Weight
Approx. 5.2kg
Ports
SCART input
1
D4 + RCA pin jack
InputA
1
RCA pin jack × 3
InputB
1
Mini D-sub 15-pin (female) blue
HDMI input
1
HDMI
Video input
1
RCA pin jack
S-Video input
1
Mini DIN 4-pin
RS-232C
1
D-sub 9-pin (male)
Trigger out
1
3.5 mm mini jack
Appendix
Storage temperature -10 – +60°C (No condensation)
Pixelworks DNXTM ICs are used in this Projector.
49
Specifications
■ Angle of tilt
If you set the projector higher than 15º, it could damage the projector and cause an accident.
■ RS-232C cable layout
• Connector shape
: D-Sub 9-pin (male)
• Projector input connector
: RS-232C
<At projector>
<At computer>
<At projector> (PC serial cable) <At computer>
GND 5
5 GND
RD
2
3
TD
TD
3
2
RD
DTR 4
6 DSR
DSR 6
4 DTR
Safety
Signal
GND Signal wire earth
TD
Transmit data
RD
Receive data
DSR Data set ready
DTR Data terminal ready
EMC
USA
UL60950-1
USA
FCC Part 15B Class B (DoC)
Canada
CSA C22.2 No.60950-1
Canada
ICES-003 Class B
EU
The Low Voltage Directive
(73/23/EEC)
IEC/EN60950-1
EU
The EMC Directive
(89/336/EEC)
EN55022 Class B
EN55024
IEC/EN61000-3-2
IEC/EN61000-3-3
Australia/New Zealand
AS/NZS CISPR 22:2002 Class B
50
Function
Specifications
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B
Personal Computers
We
Located at
Tel
: EPSON AMERICA, INC.
: 3840 Kilroy Airport Way
MS: 313
Long Beach, CA 90806
: 562-290-5254
Declare under sole responsibility that the product identified herein, complies with 47CFR Part
2 and 15 of the FCC rules as a Class B digital device. Each product marketed, is identical to
the representative unit tested and found to be compliant with the standards. Records
maintained continue to reflect the equipment being produced can be expected to be within
the variation accepted, due to quantity production and testing on a statistical basis as required
by 47CFR 2.909. Operation is subject to the following two conditions : (1) this device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
: EPSON
: Projector
: EMP-TW620
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio or television
reception. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio and television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will invalidate
the FCC Certification or Declaration of this device and may cause interference levels which
exceed the limits established by the FCC for this equipment. It is the responsibility of the user
to obtain and use a shielded equipment interface cable with this device. If this equipment has
more than one interface connector, do not leave cables connected to unused interfaces.
Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
Appendix
Trade Name
Type of Product
Model
51
Glossary
Following is an explanation of some of the terms used in this guide which may be unfamiliar or which
were not explained in the manual itself. Further information can be obtained by referring to other
commercially-available publications.
Aspect
HDTV
The ratio between an image's length and its height.
HDTV images have an aspect of 16:9 and appear
elongated. The aspect for standard images is 4:3.
An abbreviation for High-Definition Television. It refers
to high-definition systems which satisfy the following
conditions.
• Vertical resolution of 750p or 1125i or greater
(p = progressive , i = interlaced )
• Screen aspect of 16:9
• Dolby Digital audio reception and playback (or output)
Component video
Video signals which have the video brightness signals
and color signals separated, in order to provide better
image quality.
In high-definition TV (HDTV), it refers to images which
consist of three independent signals: Y (luminance
signal), and Pb and Pr (color difference signals).
Composite video
A method of image scanning whereby the signal
bandwidth used is approximately half that required for
sequential scanning when images with the same still
picture resolution are broadcast.
Video signals which have the video brightness signals
and color signals mixed together. The type of signals
commonly used by household video equipment (NTSC ,
PAL and SECAM formats).
Video signals which consist of a carrier signal Y
(luminance signal) within the color bar signal, and a
chroma or color signal (CbCr).
NTSC
Contrast
The relative brightness of the light and dark areas of an
image can be increased or decreased in order to make text
and graphics stand out more clearly, or to make them
appear softer.
An abbreviation for Phase Alternation by Line, and a
format for ground-based analogue colour television
broadcasts. This format is used in Western European
countries except France, and also in Asian countries such
as China and in Africa.
Cool-down
Progressive
This is the process by which the projector's lamp is
cooled down after it has become hot through use. It is
carried out automatically when the [Power] button on
either the remote control or the projector's control panel
has been pressed to turn off the projector. Do not turn off
the main power switch while cool-down is in progress,
otherwise the cool-down process will not work properly.
If the cool-down period is not allowed to finish normally,
the projector's lamp and internal components will remain
at high temperatures, and this may shorten the useful life
of the lamp or cause problems with the operation of the
projector. The projector takes about 30 seconds to cool
down. The actual time will vary depending on the
external air temperature.
A method of image scanning whereby the image data
from a single image is scanned sequentially from top to
bottom to create a single image.
HDMI
An abbreviation for High Definition Multimedia
Interface, and refers to a standard for digital transmission
of high-definition images and multi-channel audio
signals.
HDMI is a standard that is targeted towards household
digital equipment and computers that allows digital
signals to be transmitted in their original high quality
without compression, and it also includes a digital signal
encryption function.
52
Interlace
An abbreviation for National Television Standards
Committee, and a format for ground-based analogue
colour television broadcasts. This format is used in Japan,
North America and Central and South America.
PAL
Refresh rate
The light-emitting element of a display maintains the
same luminosity and color for an extremely short time.
Because of this, the image must be scanned many times
per second in order to refresh the light emitting element.
The number of refresh operations per second is called the
"refresh rate", and is expressed in hertz (Hz).
S-Video
A video signal which has the luminance component and
color component separated in order to provide better
image quality.
It refers to images which consist of two independent
signals: Y (luminance signal), and C (color signal).
SDTV
An abbreviation for Standard Definition Television. It
refers to standard television systems which do not satisfy
the conditions for HDTV.
SECAM
An abbreviation for Sequential Couleur A Memoire, and
a format for ground-based analogue colour television
broadcasts. This format is used in France, Eastern Europe
and the former Soviet Union, the Middle East and Africa.
Glossary
Security lock
YPbPr
A device consisting of a protector case with a hole in it
that a commercially-available theft-prevention cable can
be passed through in order to secure the device to a table
or pillar. This projector is compatible with the Microsaver
Security System manufactured by Kensington.
The carrier signal which is contained in the color bar
signal used in high-definition TV (HDTV )
transmissions. The name comes from the Y (luminance)
signal and the PbPr (color difference) signals.
sRGB
An international standard for color intervals that was
formulated so that colors which are reproduced by video
equipment can be handled easily by computer operating
systems (OS) and the Internet.
SVGA
A type of image signal with a resolution of 800
(horizontal) x 600 (vertical) dots which is used by IBM
PC/ AT-compatible computers.
SXGA
A type of image signal with a resolution of 1280
(horizontal) x 1024 (vertical) dots which is used by IBM
PC/ AT-compatible computers.
Sync. (Synchronization)
The signals output from computers have a specific
frequency. If the projector frequency does not match this
frequency, the resulting images will not be of a good
quality. The process of matching the phases of these
signals (the relative position of the crests and troughs in
the signal) is called "synchronization". If the signals are
not synchronized, problems such as flickering, blurriness
and horizontal interference can occur.
Tracking
VGA
A type of image signal with a resolution of 640
(horizontal) x 480 (vertical) dots which is used by IBM
PC/ AT-compatible computers.
Appendix
The signals output from computers have a specific
frequency. If the projector frequency does not match this
frequency, the resulting images will not be of a good
quality. The process of matching the frequency of these
signals (the number of crests in the signal) is called
"tracking". If tracking is not carried out correctly, wide
vertical stripes will appear in the projected images.
XGA
A type of image signal with a resolution of 1,024
(horizontal) x 768 (vertical) dots which is used by IBM
PC/ AT-compatible computers.
YCbCr
The carrier signal which is contained in the color bar
signal used in modern TV transmissions. The name
comes from the Y (luminance) signal and the CbCr
(chroma [color]) signals.
53
Index
A
Image size ............................................................................. 10
"Image" menu .................................................................. 27,29
Indicators ........................................................................... 6,35
"Info" menu .......................................................................... 27
Input Adjustment ............................................................. 26,28
Input Signal...................................................................... 27,33
[InputA] port............................................................ 8,12,15,49
[InputB] port ................................................................. 8,12,49
B
K
Battery replacement period (Remote control) ...................... 13
Black Level ...................................................................... 26,28
Brightness ........................................................................ 26,28
Keystone .................................................................. 6,17,27,31
C
Lamp cover ........................................................................ 8,44
Lamp Hours ......................................................................... 27
Language.......................................................................... 27,33
Lens cover.......................................................................... 6,14
Lens shift ........................................................................... 6,16
Line menu ........................................................................ 26,34
Load Memory ............................................................. 24,27,33
Ceiling......................................................................... 11,27,33
Child Lock ....................................................................... 27,31
Cinema Filter ........................................................................ 21
Cleaning the air filter ............................................................ 42
Cleaning the lens................................................................... 42
Cleaning the projector case................................................... 42
Color Adjustment........................................................ 20,26,28
Color Mode .............................................................. 7,18,26,28
Color Saturation............................................................... 26,28
Component Video ............................................................ 12,47
Composite Video.............................................................. 12,47
Configuration menu .............................................................. 26
Connecting to a computer ..................................................... 12
Connecting to a video source................................................ 12
Consumables......................................................................... 46
Contrast......................................................................... 7,26,28
Control panel........................................................................... 6
Cool-down........................................................................ 15,36
Correcting keystone distortion........................................... 6,17
Correcting projector tilt ........................................................ 17
D
Direct Power On .............................................................. 27,31
Display ............................................................................. 27,32
Display Background ........................................................ 27,32
DVI-Video Level.............................................................. 27,30
E
Epson Cinema Filter ............................................................. 21
EPSON Super White........................................................ 27,30
F
Focus adjustment ............................................................... 6,16
Front adjustable foot .......................................................... 6,17
Full Menu......................................................................... 26,34
G
Gain.................................................................................. 22,29
Gamma........................................................................ 20,26,29
H
HDTV ................................................................................... 47
[HDMI] input port ................................................... 8,12,48,49
High Altiude Mode .......................................................... 27,32
Hue and saturation ................................................................ 22
54
I
Absolute Color Temperature....................................... 20,26,28
Advanced ......................................................................... 27,30
Air filter .................................................................................. 8
Aspect ................................................................. 7,18,27,29,47
Auto ...................................................................................... 18
Auto Iris ...................................................................... 23,26,29
Automatic adjustment function............................................. 14
Auto Setup .................................................................. 24,27,31
L
M
Main power switch........................................................ 8,14,15
Memory.............................................................................. 7,24
"Memory" Menu .............................................................. 27,33
Menu Color...................................................................... 27,32
Menu Position.................................................................. 27,32
Menus ................................................................................... 26
Message ........................................................................... 27,32
N
Navigation Bar................................................................. 27,32
Normal .................................................................................. 19
O
Offset ............................................................................... 22,29
Operation ......................................................................... 27,31
Operation indicator ............................................................ 6,35
Operation Lock ................................................................ 27,31
Optional accessories ............................................................. 46
Output Scaling ................................................................. 27,30
Overheating........................................................................... 35
P
"Picture" menu................................................................. 26,28
Port................................................................................ 8,12,49
Position ............................................................................ 27,30
Power cable........................................................................... 14
Power inlet ......................................................................... 8,14
Progressive....................................................................... 27,30
Projection.................................................................... 11,27,33
Projection distance................................................................ 10
Projection image position adjustment................................... 16
Projection methods ............................................................... 11
Index
R
W
Refresh Rate .......................................................................... 27
Remote control ................................................................... 7,13
Replacing the air filter........................................................... 44
Replacing the battery............................................................. 13
Replacing the lamp................................................................ 44
Reset.................................................................. 26,27,29,31,33
Reset All........................................................................... 27,34
"Reset" menu.................................................................... 27,34
Reset Lamp Hours....................................................... 27,34,44
Reset Memory .................................................................. 27,33
Resolution ....................................................................... 27,47
RGB............................................................................. 22,26,29
RGBCMY ................................................................... 22,26,29
[RS-232C] port.............................................................. 8,49,50
Warning indicator............................................................... 6,35
White Level ...................................................................... 26,28
Wide ...................................................................................... 19
Y
YCbCr .............................................................................. 12,27
YPbPr ............................................................................... 12,27
Z
Zoom ..................................................................................... 19
Zoom adjustment................................................................ 6,16
Zoom Caption ............................................................. 19,27,29
Zoom Position .................................................................. 27,29
S
Save Memory .............................................................. 24,27,33
SCART .......................................................................... 1,27,33
[SCART] input port....................................................... 8,12,49
Screen size............................................................................. 10
SDTV .................................................................................... 47
Selecting the image source.............................................. 6,7,15
Setup Level....................................................................... 27,30
"Settings" menu................................................................ 27,31
Sharpness.......................................................................... 26,28
Sharpness (Advanced)................................................. 23,26,28
Skin Tone.................................................................. 7,20,26,29
Sleep Mode....................................................................... 27,31
Source.................................................................................... 27
Specifications ........................................................................ 49
Squeeze ................................................................................. 19
Squeeze Through................................................................... 19
sRGB ................................................................................ 19,26
Startup Screen .................................................................. 27,32
Sub-menu .............................................................................. 26
Supported Monitor Displays ................................................. 47
S-Video............................................................................. 12,47
[S-Video] input port ...................................................... 8,12,49
Sync Info ............................................................................... 27
Sync.................................................................................. 27,29
Test Pattern......................................................................... 7,17
Through ................................................................................. 19
Tint ................................................................................... 26,28
Top menu............................................................................... 26
Tracking ........................................................................... 27,29
Trigger Out ....................................................................... 27,31
[Trigger out] port................................................................ 8,49
Turning off............................................................................. 15
Appendix
T
U
Using the configuration menus ............................................. 34
User’s Logo ...................................................................... 27,32
V
Vertical Size ..................................................................... 27,29
[Video] input port.......................................................... 8,12,49
Video Signal ..................................................................... 27,33
55
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability
assumed for damages resulting from the use of the information contained herein.
Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this
product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorised modifications, repairs,
or alterations to this product, or (excluding the U.S.) failure to strictly comply with SEIKO EPSON
CORPORATION’s operating and maintenance instructions.
SEIKO EPSON CORPORATION shall not be liable against any damages or problems arising from
the use of any options or any consumable products other than those designated as Original EPSON
Products or EPSON Approved Products by SEIKO EPSON CORPORATION.
General Notice:
Macintosh, Mac, and iMac are registered trademarks of Apple Computer, Inc.
IBM is a registered trademark of International Business Machines Corporation.
Windows, WindowsNT and VGA are trademarks or registered trademarks of Microsoft Corporation in the United States.
Dolby is a trademark of Dolby Laboratories.
HDMI and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
Pixelworks and DNX are trademarks of Pixelworks, Inc.
Other product names used herein are also for identification purposes only and may be trademarks
of their respective owners. EPSON disclaims any and all rights in those marks.
SEIKO EPSON CORPORATION 2005. All rights reserved.
E
Printed on 100% recycled paper.
Printed in China
410702900
05.XX-.XA(G04)