lSSA-

on Cleamg and Maintenance

RX=Express

HIGH SPEED. ..

11015 47th Avenue W, Mukilteo, WA 98275

RX-Express

Table of Contents Page

Machine Specifications . . . . . . . . . . . . . . . . . . .

Preparation and Precautions . . . . . . . . . . . . . . . .

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cleaning Instructions . . . . . . . . . . . . . . . . . . . . .

Automatic

Maintenance

Scrubber

Repair Guide

Option . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . .

Machine Parts . . . . . . . . . . . . . . . . . . . . . . . . .

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . .

Warranty Repair Policy . . . . . . . . . . . . . . . . . . . .

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21

22

23

7

10

13

15

1

2

4

6

Copyright 01998

~LEANMASTER” Corporation

Mukilteo, Washington

182-015

No part of this manual may be reproduced or used in any form or by any means (i.e.

graphic, electronic, electronic retrieval systems) without the express written permission of the CLEANMASTER@ Corporation.

photocopying

All rights reserved.

or

Revised August 11, 1998

RX-Express

Page 1

Machine Specifications

Size: 39”1 x 42”h x 15”W

Weight:

Gearbox Oil Capacity:

Vacuum Motor:

Solution Pump:

14 oz.

(1) Three Stage 5.7”

1 17“ H20 Lift -99 CFM

Diaphragm Type, Continuous Duty, By-Pass

1.25

GPM -45 PSI Max

Solution Tank Capacity: 8.5

gallons

Recovery Tank Capacity: 8.0

gallons

Head Speed: 130 RPMs

Motor: 115 volts

1/2 HP

8.9

amps

Automatic Scrubber Attachment Kit: 1

1

Squeegee Attachment

Trailer Hook

1

1

Pad Driver Head or Brush Head Assembly

Head Removal Wrench

CleanMaster Ciq.wration

7/18/(95

RX=Express Page 2

Preparation and Precautions ~~

TO PREPARE...

Carefully remove the unit from its shipping container and inspect for damage.

damage from shipping has occurred, notify the carrier immediately.

If

The unit may come partially disassembled.

Please refer to the exploded view for a proper tank configuration.

Remove the solid shipping plug from the top of the gearbox and replace it with the vented plug provided.

if there is any evidence of oil on any of the packaging material, or in the machine itself, it may have come from the gearbox of the unit.

Check the oil level of the gearbox prior to the operation of the unit.

Important: Remove the solid shipping plug from the top of the gearbox and replace it with the vented plug provided before operating the machine.

PRECAUTIONS

1.

To avoid hazardous conditions, do not use your machine flammable and/or explosive vapors or dust are present.

in areas where

2.

3.

4.

Connect only to a grounded (3 wire) outlet.

See illustration.

row...

\

Q m,,”

—

~

.Lm~

0

WARNING: To reduce risk of electrical shock, use the equipment indoors or contained within a vehicle (i.e. service van).

Do not expose the machine to weather.

a

“~

.-m

OF m+, , m.,,

%“ mouom m..,

H

II

Grounding Instructions:

The RX-Express should be grounded while in use to protect the operator from electrical shock.

The

~ power cords are equipped with suitable three conductor plugs.

If grounded outlets are not available, use three way adapters (see Figure B).

The green (or green and yellow) conductor in the cord is the grounding wire.

Never connect

CleanMaster Corporation.

7/18/95

RX-Express

Page

3

7.

8.

5.

6.

the grounding blade to a live terminal.

Your terminal is designed to be used on less than 150 volts and has plugs resembling the one shown in Figure A.

A grounding receptacles.

adapter

The is green available

(or green locally for and yellow) connecting right adapter must be connected to a properly grounded outlet.

plugs lug extending to 2-prong from the

NOTE: Use only three wire extension cords which have three prong grounding-type plugs and three prong receptacles or adapters that accept the appliance’s plug.

Replace or repair any damaged cords.

Always disconnect the machine from the electrical outlet before servicing.

Water heaters, when required, unit.

Damage to the pumps degrees.

should be installed will occur if water in-line, downstream temperature exceeds of this

160

Empty the entire machine of water before trying to lift it.

Do not allow the recovery tank to overfill with liquid or foam.

If foam occurs, a defoamer should be used.

9.

10.

After each use of the machine, rinse out and empty the recovery tank.

Then, with the recovery lid open and the vacuum hose off, run the vacuum motor to allow the tank to dry.

Do not expose the machine to freezing temperatures.

CleanMaster Corporation 4/21/98

RX-Express

Page

4

Operation

CONTROLS

There are four switches installed in the dash box located

Two are for the VACUUM PUMP and CLEANING HEAD.

switches: 1. Automatic, and 2. Manual application of on the main handle assembly.

The SOLUTION PUMP has two solution.

MANEUVERABILITY

The ease of handling the RX-Express is a direct result of the rotary extractor head.

Its natural cleaning motion provides the “drive” for the unit.

The slightest push or pull against the foam handle provides ample effort in guiding the RX-Express through its cleaning paces.

Pivoting on its large front tires and the swivel casters in the rear allow the RX-Express to glide in and out of tight spaces and turn on a dime.

B3ckward ~

Movement

~ Forward

Movement

CLEANING PATTERN

To achieve maximum results from your unit, it is recommended that you clean in a back-and-forth motion while overlapping each cleaning pass by fifty percent.

The more soiled the area to be cleaned, the slower the speed of the cleaning passes.

This allows the machine more time to work.

After cleaning an area approximately six feet square, turn off the solution switch and make vacuum-only “dry passes” over the area to assure maximum water removal and a faster drying time.

(,--–——————~

\

“p..——— ~__ -+1

CleanMaster Corporation 7/18/95

I

RX-Express

Page 5

PUMP PRIMING MODE

Connect the auxiliary pump line supplied with the unit to the male coupler at the rear of the machine.

Disconnect the vacuum hose intake from the left side of the clear dome and place the end of the auxiliary line up into the opening in the dome.

Using your hand to create a seal around the line, turn on the vacuum and solution pumps until you see water coming out of the hose.

EMPTY MODE

Connect the auxiliary pump line to the male coupler at the rear of the machine and place the oth& end into a drain.

Turn on the solution switch and allow the remaining water to be pumped free.

A!

A+

HEAD ASSEMBLY LEVEL (HEEL-TOE) ADJUSTMENT k

I

/“k

(

~u

1!

Rem Sushing Adjustment

Roll the machine onto a flat, hard surface and lower the head to its cleaning position.

From the side, at floor level, look to see if the front and rear shoes on the cleaning head are making contact with the surface simultaneously.

If the front shoe is off the floor, the rear bushing must be loosened and moved up.

If the rear shoe is off the floor, the bushing must be adjusted down.

On the star wheel, two one-inch rubber plugs have been inserted into the plastic hub.

This is to increase the airflow of the electric vacuum motor and speed up drying time.

Remove the plugs when cleaning the star to prevent the buildup of debris in the hub.

CleanMaster Corporation 7/14/98

RX-Express

Page

6

Cleaning Instructions

2.

3.

1.

Remove the top (recovery) tank and fill the lower (solution) tank with hot water.

The higher the temperature of the water, the better the cleaning action of the machine and the chemicals used.

However, do not exceed a water temperature of 160°F.

When accessible, fill the machine directly from a utility sink using the hose supplied.

When this is not an option, a clean, five gallon bucket will suffice.

Add the necessary chemicals and replace the upper tank and dome.

Now you are ready.

CAUTION: Only non-foaming cleaning solutions can be used and absolutely no harsh solvents or petroleum products.

They will decrease the life of rubber gaskets, diaphragms and seals.

4.

Attach

Position

Lower the power the cleaning cord to a properly the machine head into grounded in the area to be cleaned.

its operating located just behind the right front wheel.

20 amp receptacle.

position by releasing the latch

5.

6.

Turn on the switches marked VACUUM PUMP and CLEANING HEAD.

To control the flow of solution, turn on either the AUTO switch for continual flow or use the MANUAL button.

Leave the AUTO switch off if the MANUAL button is used.

7.

8.

When making a “dry pass” (running vacuum only), do not use the pump in either mode.

At completion, dispose of the dirty water in the correct manner.

Also, rinse the recovery tank thoroughly before reusing the machine.

NOTE: To remove any standing water in the solution tank before storing, simply attach the three foot clear hose to the rear of the machine.

Place the other end of the hose in the recovery tank and turn on the pump to evacuate the remaining water.

9.

At the end of the day, perform the daily maintenance scheduled.

NOTE: The daily maintenance will prevent any chance of accidental freezing.

4/21/98 CleanMaster Corporation

Page 7

RX-Express

Automatic Scrubber Option -

THE KIT INCLUDES

One (1) Squeegee Attachment (mounting hardware included)

One (1) Trailer Hook

One (1) Pad Driver Head or Brush Head Assembly

One (1) Head Removal Wrench

4.

INSTALLATION

1.

INSTRUCTIONS

Remove the tanks.

Place the machine on its right side and remove the standard cleaning head.

2.

Thread on the cleaning head of your choice.

Make sure that it mounts counter-clockwise.

If you are using the pad driver head, select the proper pad for the application.

3.

Attach the saueeuee assemblv to the rear of the machine as seen below.

Crossbar

&

Cable

Retainer

-+’ o u

With the machine in its upright (cleaning) position, hook the cable retainer over the crossbar to

“disengage” the squeegee.

Replace the tanks.

Add the appropriate solution.

Lower the head onto the floor surface and turn on the head and vacuum switches.

IMPORTANT: DO NOT turn on the pump switch.

control the flow of solution.

\

Squeegee Assy

Use the push button to

5.

To resume carpet cleaning capabilities, remove the pad driver head with the wrench provided.

Place the tip of the wrench into the holes in the pad and rotate in a clockwise direction.

t

CleanMaster Corporation

7/18/95

“ RX-Express

PART NO

107-020

154-101

015-144

025-013

033-059

061-100

052-432

061-031

064-020

068-324

131-098

131-099

143-007

143-533

154-001

155-013

177-021

177-022

033-039

094-009

143-007

164-001

174-003

016-053

033-099

076-023

052-057

052-288

106-001

PARTS WITH PAD DRIVER (079-052)

DESCRIPTION

Clamp, 1 %” Spring - Wand Holder

Nut, %-20

S/S

Nylock

Screw, %-20 x 1” Eye Bolt

Tool, Head Remover

Washer, !4” SIS Flat

Pad Driver Disk

Clamp

Jet, H VsVV 8004 s/s - Port RX’s

Nipple,

1/8”

Brass Close

Coupler, 1A” Machined Rotary Union Fitting

P!U$J, 1/8”

Brass

Double Thread RX Vac Hub

Spacer, Floor Scrub Brush/Pad

Bracket, Vac Nozzle Extension

Cable, Vacuum Nozzle Lift

Clamp, Floor Scrub Cable

Handler Floor Scrub Hook

Cuff, 1 %” Gray - For Wire Reinforced Vac Hose

Knob, Vac Inlet Manifold

Vac Nozzle

Hose, 1 %” Vac w/ Wire - Gray

Squeegee Material - 1” x

1/8” x 26”

Extrusion Only - 28” Floor Scrubber

Screw, %-20 x 1” Eye Bolt

Screw, 10-24 x % Pan Hd Phillips

Spacer, % x 5/16 - s/s Solenoid Valve

Spring, Propane Regulator - H/Htr

Wheel, Floor Scrubber Wall Guard

Caster, Floor Scrubber Vac Nozzle

Page

8

QTY

1

1

2.5

ft

2

1

2

1

1

2.125

ft

1

5

1

1

1

1

1

1

2

1

1

2

8

2

1

2

1

2

2

1

CleanMaster Corporation 7/18/95

RX-Express

PART NO

033-039

094-009

143-007

143-118

164-001

174-003

016-051

076-023

052-057

052-288

106-001

107-020

154-101

015-144

025-013

033-059

061-100

052-432

061-031

064-020

068-324

131-098

131-099

143-007

143-533

154-001

155-013

177-021

177-022

PARTS WITH BRUSH ASSEMBLY (079-050)

DESCRIPTION

Clamp, 1 %” Spring, Wand Holder

Nut, ?4-20

S/S

Nylock

Screw, %-20 x 1” Eye Bolt

Screw, #8 x %” HXWSHD

Tool, Head Remover

Washer, %” s/s Flat

Brush, Floor Scrub

Jet, H

1/8VV

8004 s/s - Port RX’s

Nipple,

1/8”

Brass Close

Coupler,

1/8”

Machined Rotary Union Fitting

Plug,

1/8”

Brass

Double Thread RX Vac Hub

Spacer, Floor Scrub Brush/Pad

Bracket, Vac Nozzle Extension

Cable, Vacuum Nozzle Lift

Clamp, Floor Scrub Cable

Handle, Floor Scrub Hook

Cuff, 1 %” Gray - For Wire Reinforced Vac Hose

Knob, Vac Inlet Manifold

Vac Nozzle

Hose, 1 ?4” Vac w/ Wire - Gray

Squeegee Material - 1” x

1/8” x 26”

Extrusion Only -28” Floor Scrubber

Screw, X+-20 x 1” Eye Bolt

Screw, 10-24 x % Pan Hd Phillips

Spacer, % x 5/16 - s/s Solenoid Valve

Spring, Propane Regulator - H/Htr

Wheel, Floor Scrubber Wall Guard

Caster, Floor Scrubber Vac Nozzle

Page

9

QTY

1

1

1

5

1

2.5

ft

2

1

1

1

2

2.125

ft

2

1

2

1

1

8

2

2

1

1

1

1

2

1

2

1

2

CleanMaster Corporation 7/18/95

RX-Express

Page 10

Maintenance

MONTHLY...

2.

3.

1.

Check the oil level in the gearbox on a monthly basis.

This is a permanent lubricated gearbox.

You do not need to change the oil.

However, maintaining the proper oil level is important.

To check the oil level, remove the vent plug and look into the gearbox.

Turn the “star” until you can see the inspection hole in the gear.

With the unit sitting flat, the oil level should be up to, but not over, the middle of the gear.

If oil needs to be added, use a quality 80-90 weight gear oil.

HELPFUL HINT: When checking the oil level in the gearbox, use a dipstick.

The oil level should read 3/8”.

a toothpick as

Remove and rinse the filter screen from the- flow control valve.

Change the felt seal.

This is recommended after every ten hours of use.

(For step by step instructions on removing the cleaning head and the seal, please refer to the “REPAIR GUIDE” section. ) Always keep a spare felt seal soaking in 30 weight oil.

By immersing the felt in oil, it will expand like a sponge and provide sufficient seal for a good vacuum.

Place the worn seal back in the oil bath to rejuvenate.

HELPFUL HINT: An ideal container in which to soak the spare felt seal is a commercial tuna can.

It is the right size and shape and does not require a large amount of oil.

After placing the refreshed, oil-soaked felt seal in the hub, coat the surface with 30 weight gear oil.

Lightly oil the inner hub

*

\

>

CleanMaster Corporation 7/18/’95

RX-Express threads before re-attaching the cleaning head to the machine.

Page 11

WEEKLY...

1.

Clean the lid thoroughly by removing the tanks and clearing the lid of debris.

2.

3.

Remove and clean the pick-up hose filter inside the solution tank with a vinegar and water solution to remove the chemical deposits.

Check the applicator jets in the head to insure a proper solution flow.

If the flow is restricted, clean the jets.

Twist the jet out.

Turn it over.

Blow out any obstructions and reinstall the jet.

NOTE: Do not use any sharp objects to clear obstructions from the jets.

This will damage the jets.

UNEVEN DRIBBLE CORRECTLY

ATOMIZED

DAILY...

~

Clean off any accumulated debris on the gearbox shaft or inside the threaded portion of the hub.

An accumulation of debris around the gearbox shaft, if not removed, may damage the gearbox oil seal resulting in loss of oil in the gearbox.

If the gearbox is operated without oil, severe damage may occur.

(This requires removing the cleaning head.

To do this, please refer to the “REPAIR GUIDE” section. )

CleanMaster Corporation 4/21/98

RX=Express

Page 12

Coat themotor shaft with lubricant before reinstalling the cleaning head.

Locate the head onto the shaft, making sure the threads are aligned properly, and rotate the head counter-clockwise.

CleanMaster Corporation 4/21/98

RX-Express

Page 13

Repair Guide

IMPORTANT electrical parts.

Make sure the machine is

unplugged

before the removal of any

Removal of Cleaning Head:

1.

First, unscrew the head in the same direction it turns during

2.

operation (or clockwise when looking from the underside).

Once you have loosened the assembly, spin if off with your hands.

If the cleaning head is difficult to remove, you may use a %“ socket wrench on the exposed center nut.

Replacing of Felt Seal:

A worn or “dried out” felt will not form a proper vacuum seal.

This will impair the extraction capabilities of the unit.

Therefore, the carpets are left more wet than is desirable.

1.

Remove cleaning head assembly.

2.

3.

Make sure felt is saturated with oil to insure a proper seal.

Remove and reverse seal so that ‘“new” face is against hub.

NOTE: Alternating sides will temporarily extend the life of the felt.

However,

4.

the seal may need to be replaced.

Reinstall head assembly.

NOTE: When reinstalling the head assembly, you should be able to “feel” the felt compacting against the seal plate during the last quarter rotation of the head.

Removal of Vacuum Motor:

1.

Disconnect machine from power source.

2.

Remove hose from end of vacuum motor.

Remove 10-24 screws from side of frame.

3.

4.

5.

Lift motor.

Disconnect wires at terminal clips.

Removal and Re-installation of Solution Pump:

1.

Disconnect machine from power source.

2.

3.

Check that ail water

Disconnect has been evacuated from unit.

?4” hoses on either side of pump.

4.

5.

Remove four (4) 10-24 screws and nuts mounting pump to side of frame.

Disconnect wires at wire nuts.

CleanMaster Corporation 7/18/95

RX-Express

6.

7.

Remake wire connections with new wire nuts.

Re-install in reverse order.

Removal of Fiow Control Valve:

1.

2.

3.

4.

Disconnect machine from power source.

Evacuate all water from unit.

Disconnect %” and

3/8” hoses attached to valve.

5.

6.

7.

Remove male quick connect from top of frame.

Remove %” elbow behind quick connect.

Disconnect wires.

Lift complete valve assembly from unit.

Removal of Cleaning Head / Pivot Frame Assembly:

1.

Disconnect machine from power source.

2.

3.

4.

5.

6.

7.

8,

Remove

Remove

Disconnect

Remove

Loosen

Remove vacuum two wires control hose attached hose attached to rotary to front of head.

at rear of motor.

union.

link from rear of shaft.

(2) set screws spring from

Pull head forward lifting in pivot bearing.

mechanism.

to disengage from frame.

Page 14

...

CleanMaster Corporation 7/18/95

RX-Express

4

I (

L

I

,?i-

5

\

10 ‘

/

11

CleanMaster Corporation

.

1

17

18

/

13

12

Page 15

Machine Parts

22

21

20

19

6/19/’96

Page 16

RX-Express

62

63L

“=---+”””’’--””

IJ

‘?

,, ;< \;;: ‘“ ‘“

.,

.,x, “

L

. ..>.

.

,

5

CleanMaster Corporation

54

/

% w

J A

\.

d

“ /“a

&

\

52

48

’47

12/26/97

RX-Express

PART NO

000-052-099

000-052-276

000-068-017

000-059-001

000-006-009

000-105-008

000-143-166

000-107-089

000-107-020

000-068-174

000-143-012

000-064-012

000-094-009

000-143-162

000-076-057

000-052-089

000-052-080

000-057-047

000-055-057

000-094-009

000-085-012

000-015-145

000-143-080

000-143-096

000-174-021

000-106-014

604-052-012

000-157-111

000-100-017

000-143-315

000-061-001

000-061-026

000-108-012

000-061-029

000-085-010

000-141-023

000-052-309

000-111-124

000-033-004

ITEM

1

2

3

4

5

6

7

8a

8b

9

10

11

28

29

30

31

32

33

35

36

37

38

39

19

20

21

22

23

16

17

18

12

13

14

15

24

25

26

27

Page 17

DESCRIPTION QTY

Insert, #26

Rotary Union %“ NPT

Hose,

3/8”

Rubber

Gearbox, Complete - Spur

Base, High Speed

Plate, Cast Base - Seal

Screw, % -20 x 1” s/s BHCS

Star, Stainless Steel Heat Treated

Hub, Double Thread RX Vacuum

Hose, 1” ID Gray - Vacuum

43/16

1

1

Screw,

5/16 -18

Head, New x %“ s/s, HHCS

RX Skid Assembly

Nut, % -20 S/S Nylok

5

SCI%W, 5/16 X I” StriPP13r % ZO S/S

5

Jet, 110015 Quick Connect (Jet, O-ring, Body) 5

Elbow,

‘/8”

Brass Female

5

5

5

Nipple,

1/8” x 4“ Brass

Gasket, Felt Hub

Frame, Pivot

5

1

1

Nut, % -20

Link, Torsion

Bracket,

Electric

Auto

S/S

Bar

Washer,

3/8” k)ck

Motor

Nylok

Floor Scrub

Plug, Gearbox Vent

Assembly

Hitch

Screw, % -20 x 1” s/s SHCS

Screw,

3/8 16 x %“, s/s HHCS

Switch, Chrome Momentary 10224

1

2

2

1

5

12

1

1

Panel,

Screw,

Handle,

RX-Express

% -20 x %“ Rnd Hd Phillips

Foam Grip

Switch

Handle, RX-Express Upper Aluminum

Protector, Power Cord Relief Grip

Main Handle, RX-Express

1

1

2

2

Linkage, insert,

Pump,

Steel Clevis Yoke

Rod, RX-Express

#68 Plastic

Low PSI

Linkage

Elbow

Clamp, Size 6Mini Hose

1

2

1

1

1

1

1

1

1

5

~t

1

1

1

1

CleanMaster Corporation 4/21/98

‘,

RX-Express

ITEM PART NO

51

52

54

55

56

57

58

59

60

47

48

49

50

40

41

42

43

44

45

46

61

62

63

64

65

Not Shown:

000-052-117

000-052-050

000-057-055

000-174-011

000-052-090

000-052-071

000-052-085

000-052-061

000-169-119

000-052-104

000-068-018

000-141-025

000-177-018

000-141-026

000-055-056

000-177-019

000-015-141

000-111-129

000-052-117

000-052-448

000-157-115

000-143-167

000-094-034

000-143-051

000-106-033

000-001-070

000-008-032

000-015-146

000-049-100

000-052-201

000-052-436

000-081-157

000-085-015

000-094-026

000-106-025

000-131-014

000-131-050

000-134-008

000-178-044

CleanMaster Corporation

Page 18

DESCRIPTION QTY

Insert, #48

Quick Connect, 440 Male w/ Viton - Standard

Gasket, Garden Hose

Washer,

9/16”

Brass - Fiber Glass

Tee, %” Male Branch M-F-F

Nipple, % Brass Hex

Elbow, %” Brass Street

Bushing,

3/8

M x !4 F Brass

Valve, 11 Ov Solenoid

Insert, #66

Hose, %” Rubber

Axle, RX-Express Rear

Caster, RX-Express Rear

Axle Assembly, High Speed RX-Express Front

Frame, High Speed RX-,Express

Wheel, RX-.Express

Front

Bracket, Vat.

Motor Mount - Acustek

Motor, 3-Stage Vac Acustek 120 volt

Insert, #48

Quick Connect, !4” Male x !4” FPT - Special

Switch, 16 amp Mini Rocker w/ Terminal

Screw, 10-24

Nut, 10-24

S/S x 1 % BTN HD s/s

Nylock

Screw, 8-32 x %” s/s Phil Binder Head

Plug, 20 amp Male Twist Lock

2

1

1

1

1

1

2

1

1

3

4

4

4

1

2

2 Ft

1

1

1

1

2

4

1

1

3

Adapter, 1

7/8” x 1 %” Vac Motor Outlet

Bearing,

Bracket,

Filter,

%” Pillow

Acoustical

Solution

Block

Foam Support

Pick Up

1

Sleeve, 1 ?4” Vacuum Inlet

Quick Connect, ?4” F x %” FPT

Label Set, Generic RX-Express Operating Inst.

Linkage, %-28 Ball Joint

Nut, Nylon Solution Feed Filter

Plug, #3 Rubber Stopper

Gasket,

Sheet

Roto Shroud

Foam Set, 3-Piece Acoustical Foam

Receptacle, 20 amp Female Twist Lock

Cord, 50’ Primary (includes part #1 34-008)

2% Ft

1

1

2

1

1

1

1

1

1

1

1

1

8/11/98

RX-Express

Page 19

11

12

11

ITEM

1

7

8

9

10

4

5

2

3

11

12

13

14

15

PART NO

000-159-0361

000-057-060

105-041-001

000-049-0201

000-061-025

000-106-104

000-052-432

000-068-324

000-143-315

000-081-153

000-159-035

000-143-054

000-041-076

000-061-003

CleanMaster Corporah”on

DESCRIPTION QTY

Tank, RX-fFxpress Vacuum

Gasket, RX-lSxpress Vacuum

Cover, Vacuum Tank Assembly

Filter Screen, Modified for RX-Expfess Dome

Handle, RX-Express Vacuum Tank Bail

Stopper Assy, Clear Tank

Cuff, 1 %” Gray for Wire Reinforced Vac Hose

Hose, 1 %” Vacuum w/ Wire - Gray

Screw, K -20 x %“ Rnd Hd Phillips

Label Set, RX-Express

Tank, RX-Express Solution

Screw, 8-32 x %“ BHCS

Cover, RX-Express Front Vacuum Form

Handle, 6“ Black Tank

1

1

2

9 Ft

2

1

1

1

1

4

1

1

1

1

8/15/97

RX-Express

PART NO

000-068-194

000-068-332

000-079-050

000-079-052

000-163-023

000-164-020

100-011-101

190-041-020

190-041-021

190-041-022

Page 20

Accessory Parts List

DESCRIPTION

Hose, 1 %” x 15’ Vacuum

Hose, 15’ F x F Solution

Kit, Auto Scrubber with Brush Assembly

Kit, Auto Scrubber with Pad Driver

CM-1 Deluxe Upholstery Tool with LP Valve

CM-CHSV Upholstery Tool 4“, Closed Head, 1 %” DIA

CM S1 1 A Carpet Wand 11” LP Powder Coated, 1 %” s/s

Rotary Extractor Pad Driver with Hub

Rear Assembly, Auto Floor Scrubber

Rotary Extractor Brush Assembly with Hub

CleanMaster Corporation 6/19/96

RX-Express

Page 21

Witing Diagram

I

~“’m(”)

L

GREEN (14)

M:FmBMcKf

I

L

SOLENOID

VALVE

BLuE(1S)

1

SO#J;N

- ORANGE (14)

VACUUM

MOTOR

CLEANING

HEAD

( “)

: 55

WHITE (12)

=

CleanMaster Corporation 7/21/97

~

RX-Express

Page 22

Warranty Repair Policy

When requesting warranty information, information: call or write and provide the following

1.

2.

3.

4.

When and where the equipment in question was purchased.

Model and serial number of machine.

Part number and description of part.

Description of failure or defect.

Upon receipt of the above information, a Material Return Authorization will be issued.

All packages should be prepaid and clearly marked with the Material Return

Authorization number.

If these conditions are not met, shipment will be refused.

After evaluation, the item(s) will be repaired or replaced at our discretion.

If failure or defect is the result of physical abuse, or if the warranty period has repairs will be charged to the customer.

expired,

For service, contact the distributor where the machine was purchased call our Customer Service Department.

or

Monday through Friday .8:00

Parts:

Service:

Parts and Service FAX:

(425)

(425)

(800) am To 5:00

775-7276

775-7275

426-4225 pm PST

PST ROCK MT.

CENTRAL EASTERN

CleanMaster Corporation

I

I

RX-Express

Page

23 tl

5 -3-1 WARRANTY

CleanMaster products are warranted to be free of defects either 5 years, 3 years, or 1 year as noted below: in material for a period of

* 5 Years on Roto Cast Molded Tanks

* 3 Years Prorated on Drive Motor Gearbox Assembly (RX-Express Only)

* 1 Year on Vacuum Motors, Pumps, Switches, Fittings, Etc.

* 1 Year on HushhVac Vacuums

During this warranty period, we will repair or replace, at our sole option, free of charge, any parts shown to be defective in either material or workmanship.

Said parts must be returned with postage or freight pre-paid.

Specific parts, such as switches, vacuum motors, pumps, fittings, etc., are also warranted for a period of 1 year from date of original purchase.

This warranty is for replacement of defective parts or workmanship only.

IT DOES NOT

PROVIDE FOR REPLACEMENT OF COMPLETE UNITS DUE TO DEFECTIVE PARTS.

It does NOT cover normal wear items such as hoses, power cords, bumpers, carbon brushes, gaskets, etc., which require replacement as a result of ordinary usage.

Also, failures caused by abuse, neglect-r alterations or operation contrary.

to manufacturer’s recommendations are not warranted.

Replacements period.

parts are warranted only for the remainder of the original warranty

This warranty does not cover labor or other charges in connection with replacement parts.

NO LOCAL SERVICE OR REPAIR CHARGES ARE ALLOWED UNLESS PRIOR

AUTHORIZATION IS OBTAINED.

J

There are no other warranties, expressed or implied, made with respect to this equipment.

The manufacturer assumes no responsibility for damages resulting from the use or misuse of this equipment.

~ d-

CORPORA TION

11015 47th Avenue W ● Mukiiteo, WA 98275

CleanMaster Corporation 4/24/97