Raymarine HSB2 Plus Series Owner's Handbook Manual

hsb2 PLUS Series
Fishfinders
Owner’s
Handbook
Document number: 81195_2
Date: August 2002
hsb2 Plus Series Fishfinders
iii
hsb2 Plus Series Fishfinders
Owner’s Handbook
August 2002
Intended Use
Raymarine hsb2 Plus Series Fishfinders are intended for recreational
fishfinding. The combined Fishfinder/Chartplotter devices are intended for
recreational fishfinding and course chartplotting. The optional chartplotter
function is intended as an aid to navigation and should not be relied upon as a
substitute for official navigation charts.
SAFETY NOTICES
This equipment must be installed and operated in accordance with the
instructions contained in this manual. Failure to do so can result in personal
injury and/or navigational inaccuracies. In particular:
1. HIGH VOLTAGE. The LCD display unit contains high voltages.
Adjustments require specialized service procedures and tools only available
to qualified service technicians – there are no user serviceable parts or
adjustments. The operator should never remove the display unit cover or
attempt to service the equipment.
2. NAVIGATION AID. The chartplotter unit is only an aid to navigation. Its
accuracy can be affected by many factors, including equipment failure or
defects, environmental conditions, and improper handling or use. It is the
user’s responsibility to exercise common prudence and navigational
judgements. This unit should not be relied upon as a substitute for such
prudence and judgement.
EMC Conformance
All Raymarine equipment and accessories are designed to the best industry
standards for use in the recreational marine environment.
The design and manufacture of Raymarine equipment and accessories
conform to the appropriate Electromagnetic Compatibility (EMC) standards,
but correct installation is required to ensure that performance is not
compromised.
iv
hsb2 Plus Series Fishfinders
Preface
This handbook describes the following Raymarine hsb2 Plus Series Fishfinder
Displays:
• L755RC Plus 7" Monochrome LCD Fishfinder Display with Chartplotter
• L760 Plus 7" Color LCD Fishfinder Display
• L760RC Plus 7" Color LCD Fishfinder Display with Chartplotter
• L1250 Plus 10.4" Color LCD Fishfinder Display
• L1250RC Plus 10.4" Color LCD Fishfinder Display with Chartplotter
The combined Fishfinder/Chartplotter display units include a cartridge holder
assembly that contains two slots for C-MAP NT or NT+ chart cards.
Fishfinder systems require an appropriate Raymarine transducer unit and
inter-connecting cable. Details for selecting and installing the transducer are
described in document number 81196, Transducers for Fishfinders Owner’s
Handbook.
This handbook contains very important information on the installation and
operation of your new fishfinder. In order to obtain the best results in operation
and performance, please read this handbook thoroughly.
Raymarine’s Technical Services representatives or your local dealer will be
available to answer any questions you may have.
TFT LCD Displays
The colors of the display may seem to vary when viewed against a colored
background or in colored light. This is a perfectly normal effect that will be
seen with all color LCD displays.
In common with all Thin Film Transistor (TFT) LCD displays, the screen may
exhibit a few (less than 20) wrongly illuminated pixels. These may appear as
black pixels in a light portion of the screen, or as colored pixels in black areas.
CAUTION:
To provide protection against the damaging effects of UV light, it is
advisable to replace the sun cover provided when the color LCD display is
not in use.
hsb2 Plus Series Fishfinders
v
Raymarine Products and Services
Raymarine products are supported by a network of Authorized Service
Representatives. For information on Raymarine products and services,
contact either of the following:
United States
Raymarine, Inc.
22 Cotton Road, Unit D
Nashua, NH 03063-4219
USA
Telephone: 1-603-881-5200
1-800-539-5539
Fax:
1-603-864-4756
Europe
Raymarine Ltd
Anchorage Park
Portsmouth, Hampshire
England PO3 5TD
Telephone: +44 (0) 23 9269 3611
Fax:
+44 (0) 23 9269 4642
Or, you may contact us on the World Wide Web at www.raymarine.com.
Warranty
To register your hsb2 Plus Series display unit ownership, please take a few
minutes to fill out the warranty registration card found at the end of this
handbook. It is very important that you complete the owner information and
return the card to the factory in order to receive full warranty benefits.
Technical Accuracy
The technical and graphical information contained in this handbook, to the
best of our knowledge, was correct as it went to press. However, the
Raymarine policy of continuous improvement and updating may change
product specifications without prior notice. As a result, unavoidable
differences between the product and handbook may occur from time to time,
for which liability cannot be accepted by Raymarine.
vi
hsb2 Plus Series Fishfinders
Raymarine is a registered trademark of Raymarine Limited.
SeaTalk is a registered trademark of Raymarine Limited.
hsb2 is a trademark of Raymarine Limited.
Pathfinder Plus is a trademark of Raymarine Limited.
This product contains technology provided under license by Acorn Group plc.
The copyright of this intellectual property is acknowledged by Raymarine,
Inc. as are Acorn’s trademarks and patents. Acorn’s world wide web address is
http://www.acorn.com.
© Raymarine, Inc. 2002
Contents
vii
Contents
EMC Conformance ......................................................................... iii
Warranty .......................................................................................... v
Chapter 1:
Overview ......................................................................................... 1-1
1.1 Introduction .................................................................................. 1-1
General .......................................................................................... 1-4
Introduction to hsb2 Systems ......................................................... 1-5
Display Unit Features ................................................................... 1-5
Operating Modes .......................................................................... 1-6
1.2 The Fishfinder Display ................................................................. 1-8
Fishfinder Options ........................................................................ 1-9
Fishfinder Functions ................................................................... 1-10
1.3 The Chartplotter Display ............................................................ 1-12
Chartplotter Display Options ...................................................... 1-13
Chartplotter Functions ................................................................ 1-15
1.4 Operating Controls ..................................................................... 1-16
Trackpad and Cursor ................................................................... 1-17
Dedicated Keys ........................................................................... 1-19
Soft Keys ..................................................................................... 1-19
Pop-Up Menus ............................................................................ 1-20
Database Lists ............................................................................. 1-21
Chapter 2:
Installation ..................................................................................... 2-1
2.1 Introduction .................................................................................. 2-1
Planning the Installation ............................................................... 2-3
EMC Installation Guidelines ........................................................ 2-3
2.2 Unpacking and Inspecting the Components ................................. 2-5
2.3 Selecting the Equipment Location ................................................ 2-7
Display Unit Mounting Location .................................................. 2-7
2.4 Cable Runs .................................................................................. 2-11
Power Cable ................................................................................ 2-11
Transducer Cable ........................................................................ 2-11
viii
hsb2 Plus Series Fishfinders
2.5 Mounting the Display Unit ......................................................... 2-12
2.6 System Connections ................................................................... 2-14
Display Unit Connection ............................................................ 2-15
EMC Conformance ..................................................................... 2-18
2.7 Integrated Systems ...................................................................... 2-18
High Speed Bus (hsb2) ................................................................ 2-19
SeaTalk and NMEA In ................................................................ 2-22
Using the SeaTalk Auxiliary Junction Box ................................. 2-26
Data Output ................................................................................. 2-28
Data Conversion ......................................................................... 2-28
2.8 Integrated System Checks .......................................................... 2-29
Chart Display .............................................................................. 2-29
Received Data ............................................................................. 2-29
Transmitted Data ........................................................................ 2-29
Chapter 3:
Getting Started & Adjusting the Display ................................... 3-1
3.1 Introduction .................................................................................. 3-1
Conventions Used ......................................................................... 3-1
Simulator ...................................................................................... 3-1
3.2 Switching the Display On and Off ................................................ 3-2
Simulator Mode ............................................................................ 3-5
Changing the Lighting & Contrast (Monochrome LCD) ............. 3-6
Changing the Brightness & Color Settings (Color LCD) ............. 3-6
3.3 Controlling the Display ................................................................. 3-9
Selecting the Mode of Operation .................................................. 3-9
3.4 Fishfinder Display Control Functions ........................................ 3-15
Viewing Data Boxes ................................................................... 3-15
Changing the Scroll Speed .......................................................... 3-15
Selecting the Power Setting ........................................................ 3-17
Changing the Fishfinder Range .................................................. 3-17
Selecting the Frequency .............................................................. 3-20
Using Bottom Lock ..................................................................... 3-21
Using A-Scope ............................................................................ 3-23
Using Zoom ................................................................................ 3-24
3.5 Chart Display Control Functions (Raychart Models) ................. 3-26
Customizing the Screen Presentation Options ............................ 3-26
Contents
ix
Moving Around the Chart ........................................................... 3-28
Chapter 4:
Fishfinder Operations ................................................................... 4-1
4.1 Introduction .................................................................................. 4-1
4.2 Interpreting and Adjusting the Fishfinder Image .......................... 4-1
Fish Indications ............................................................................. 4-2
Bottom Indications ....................................................................... 4-3
Using White Line .......................................................................... 4-4
Adjusting Display Gain (Sensitivity) ........................................... 4-4
4.3 Fishfinder Data Window ............................................................... 4-7
4.4 Using Alarms ................................................................................ 4-8
4.5 Using VRM to Determine Depth & Distance from Boat .............. 4-9
4.6 Waypoints ................................................................................... 4-11
Placing a Waypoint ..................................................................... 4-11
4.7 MOB ........................................................................................... 4-13
Chapter 5:
Standard Chart Operations .......................................................... 5-1
5.1 Introduction .................................................................................. 5-1
5.2 Using Chart Cards ......................................................................... 5-2
Inserting a Chart Card ................................................................... 5-2
Removing a Chart Card ................................................................ 5-3
Displaying the Chart Data ............................................................. 5-3
Displaying Chart Object and Source Information ........................ 5-4
5.3 Working with Waypoints .............................................................. 5-8
Introduction .................................................................................. 5-8
Placing a Waypoint ....................................................................... 5-9
Selecting a Waypoint .................................................................. 5-12
Waypoint Data Display ............................................................... 5-13
Editing the Waypoint Details ...................................................... 5-13
Erasing a Waypoint ..................................................................... 5-15
Moving a Waypoint .................................................................... 5-15
Using the ST60 or ST80 Navigator Keypad ............................... 5-16
5.4 Working with Routes .................................................................. 5-18
Creating a New Route ................................................................. 5-19
Saving the Current Route ............................................................ 5-22
x
hsb2 Plus Series Fishfinders
Clearing the Current Route ......................................................... 5-24
Retrieve a Route From the Database ........................................... 5-24
Displaying Route Information .................................................... 5-25
Using the Route List to Erase and Name a Route ....................... 5-27
Editing a Route ........................................................................... 5-28
5.5 Following Routes and Going to Points ....................................... 5-30
Follow a Route ............................................................................ 5-30
Target Point Arrival .................................................................... 5-31
Other Follow Route Options ....................................................... 5-32
Going To an Individual Target Point ........................................... 5-33
Stop Follow or Stop Goto ............................................................ 5-34
5.6 Transferring Waypoints and Routes ........................................... 5-35
5.7 Using Tracks ............................................................................... 5-39
Setting Up a Track ...................................................................... 5-40
Clearing the Current Track ......................................................... 5-40
Managing Tracks ........................................................................ 5-40
SmartRoute ................................................................................. 5-42
5.8 Typical Chart Scenarios .............................................................. 5-43
Place and Goto a Waypoint ......................................................... 5-44
Make and Follow a Route ........................................................... 5-46
Review Your Passage Plan .......................................................... 5-48
Chapter 6:
Further Chart Operations ............................................................. 6-1
6.1 Introduction .................................................................................. 6-1
6.2 Measuring Distances Using the VRM/EBL Key .......................... 6-2
6.3 Alarms and Timers ........................................................................ 6-4
Alarm Reporting ........................................................................... 6-4
Setting Alarms and Timers ........................................................... 6-5
6.4 Man Overboard (MOB) ................................................................ 6-6
6.5 Cursor Echo .................................................................................. 6-7
6.6 Radar Overlay ............................................................................... 6-7
6.7 GPS Setup ..................................................................................... 6-9
6.8 Data Log Mode ........................................................................... 6-10
Contents
Chapter 7:
xi
Setting Up the System Defaults .................................................. 7-1
7.1 Introduction .................................................................................. 7-1
7.2 Changing the Set Up Parameters .................................................. 7-2
7.3 System Set Up Parameters ............................................................ 7-4
Data Boxes .................................................................................... 7-6
Bearing Mode ............................................................................... 7-6
Cursor Reference .......................................................................... 7-6
Cursor Readout ............................................................................. 7-7
Day/Night (Monochrome Display only) ...................................... 7-7
Help ............................................................................................... 7-7
Soft Keys ....................................................................................... 7-7
Key Beep ...................................................................................... 7-7
MOB Data ..................................................................................... 7-8
Autopilot Pop Up .......................................................................... 7-8
Menu Timeout Period ................................................................... 7-8
Units .............................................................................................. 7-8
Variation Source ........................................................................... 7-8
Bridge NMEA Heading ................................................................ 7-9
NMEA-Out Set Up ....................................................................... 7-9
Cursor Echo (Systems with Radar Display) ............................... 7-11
Date and Time Settings ............................................................... 7-11
GPS SOG/COG Filter ................................................................. 7-11
Compass Set Up .......................................................................... 7-12
Language .................................................................................... 7-12
Simulator .................................................................................... 7-12
7.4 Fishfinder Set Up Parameters ..................................................... 7-13
Target Depth ID .......................................................................... 7-13
Color Bar ..................................................................................... 7-13
Depth Digit Size .......................................................................... 7-14
Sonar HSB Mode ........................................................................ 7-14
Depth Offset ................................................................................ 7-14
Speed Calibrate ........................................................................... 7-14
Temperature Calibrate ................................................................ 7-14
Sonar History .............................................................................. 7-14
Depth Range (L1250 Plus and L1250RC Plus only) .................. 7-15
Sonar Simulator .......................................................................... 7-15
xii
hsb2 Plus Series Fishfinders
7.5 Chart Set Up Parameters (Raychart Models) .............................. 7-16
Customize Chart ......................................................................... 7-16
Plotter Mode ............................................................................... 7-17
Chart Orientation ........................................................................ 7-17
Object Information ..................................................................... 7-18
Palette (Color LCDs only) .......................................................... 7-18
Waypoint Options ....................................................................... 7-18
Vectors ........................................................................................ 7-18
Radar/Chart Synch (Systems with Radar Display) ..................... 7-19
Datum Selection ......................................................................... 7-19
Position Offset ............................................................................ 7-19
Chapter 8:
Maintenance and Problem Solving ............................................. 8-1
8.1 Maintenance ................................................................................. 8-1
Routine Checks ............................................................................. 8-1
Cleaning Instructions .................................................................... 8-1
EMC Servicing and Safety Guidelines ......................................... 8-2
8.2 Resetting the System ..................................................................... 8-3
8.3 Problem Solving ........................................................................... 8-4
How to Contact Raymarine .......................................................... 8-5
Worldwide Support ....................................................................... 8-7
Appendix A:
Specifications ...............................................................................A-1
hsb2 Plus Series Fishfinder Displays ............................................ A-1
Appendix B:
Using the Auxiliary Junction Box ................................................ B-1
Raystar 112, 105, Apelco 182 and 182XT ................................... B-2
Autohelm GPS, Z260 and Z273 .................................................. B-3
Raystar 112LP (SeaTalk version) ................................................ B-4
Raystar 114 Combined GPS and Differential Beacon Receiver .. B-5
Raystar 120 WAAS Satellite Differential Receiver ..................... B-6
Appendix C:
C-MAP Chart Card Features ........................................................ C-1
Appendix D:
SeaTalk and NMEA Data ..............................................................D-1
Appendix E:
Abbreviations ............................................................................... E-1
Chapter 1: Overview
1-1
1.1 Introduction
This handbook describes the following hsb2 (High Speed Bus) Plus Series
Fishfinder displays:
Fishfinder
Display Type
Display Size
Chartplotter
L755RC Plus
Monochrome LCD
7 inch
Yes
L760 Plus
L760RC Plus
Color LCD
Color LCD
7 inch
7 inch
No
Yes
L1250 Plus
L1250RC Plus
Color LCD
Color LCD
10.4 inch
10.4 inch
No
Yes
Raymarine hsb2 Plus Series Fishfinders use the latest processor and sonar
technology for accurate performance and echo detection. Units feature 7" or
10.4" daylight viewable monochrome or color LCD displays and the
Raychart (RC) models include a full C-Map NT/NT+ Chartplotter. With up to
600 watts output power and dual frequency operation, hsb2 Plus Series
Fishfinders provide performance from 1 up to 3000 ft. In fact, the L1250 Plus
and L1250RC Plus units offer 1000 watts power and a depth range up to 5000
ft.
Use the High Speed Bus (hsb2), SeaTalk and NMEA interfaces to provide an
integrated system with additional devices, such as Pathfinder Plus Radar,
Raymarine Autopilot and Raystar Wide Area Augmentation System (WAAS)
GPS products.
Connecting an hsb2 Series Plus Fishfinder to an hsb2 Series Pathfinder Plus
Radar and to an hsb2 Series Plus Chartplotter enables fishfinder, radar, and
chart data to be displayed on all three units. Similarly, chart data can be
repeated on a fishfinder-only device from any via hsb2 from any other hsb2
device with chart capabilities.
This handbook describes the display unit controls and details both fishfinder
and chart operations. Controls that are specific to either fishfinder or
chartplotter are described in fishfinder or chart sections/chapters.
Note: Many illustrations in this handbook show example screens. The screen
you see on your display depends on your system configuration and set up options, so it may differ from the illustration.
Introduction
Chapter 1: Overview
1-2
hsb2 Plus Series Fishfinders
How to Use This Handbook
Introduction
If you are installing the display system yourself, you should read Chapter 2
before you start the installation. This chapter also provides information that
will be useful if you are connecting your hsb2 Plus Series system to other
equipment.
For an overview of the display unit controls, the fishfinder and the chartplotter
systems, read Chapter 1. Chapter 3 will help you start using your system.
For detailed information on fishfinder operations refer to Chapter 4.
For chartplotter operating details, refer to Chapter 5 and Chapter 6.
To change the system set up defaults, read Chapter 7.
Chapter 2 provides planning considerations and detailed instructions for
installing the fishfinder display unit. It should be referred to when you are
ready to install the system. Details to connect the display to other equipment
via hsb2, NMEA and SeaTalk are also provided.
Chapter 3 explains how to start using the display and describes how to use
some of the basic fishfinder and chart functions. Chapter 3 also provides
operating guidelines for typical chartplotter scenarios; these guidelines
introduce you to many of the chartplotter functions.
Chapters 4 provides detailed operating information for the fishfinder
functions - selecting depth range limits, adjusting gain, color and STC, setting
alarms, using the VRM marker, marks and man overboard.
Chapter 5 provides detailed operating information for the standard
chartplotter functions - using chart cards, plotting waypoints and routes,
following routes and showing tracks.
Chapter 6 provides detailed operating information for further chart functions,
including measuring distances, man overboard and cursor echo. It includes
instructions for setting up a differential GPS.
Chapter 7 provides instructions for setting up your system to suit your
preferences. You should read this chapter to determine how to set up the
fishfinder and chartplotter system defaults.
Chapter 8 provides information on user maintenance, and what to do if you
experience problems.
The Appendices provide additional information that you may find useful:
Appendix A lists the technical specifications for the fishfinder and for the
chartplotter.
Appendix B provides details on connecting the display unit to specific GPS
systems.
Chapter 1: Overview
1-3
Appendix D defines the SeaTalk and NMEA data that is transferred on
integrated systems.
A List of Abbreviations, Index and warranty information are included at the
end of the handbook.
A summary of the fishfinder and chartplotter controls are provided on the
Quick Reference Cards supplied with your system.
Terminology
The following terminology is used to describe the various display unit
configurations:
Master
A unit capable of sourcing specific data such as
fishfinder, chart, or radar data.
Repeater
A unit capable of displaying data, such as radar,
from the High Speed Bus.
Fishfinder Display
Unit providing Fishfinder Master and Radar
Repeater functionality. The L755RC, L760RC,
and L1250RC Plus displays also provide Chart
Master functionality.
Radar Display
Unit providing Radar Master, Fishfinder
Repeater and Chart Reader functionality.
Chart Display
Unit providing Chart Master, Fishfinder
Repeater and Radar Repeater functionality.
Combined Display
Unit providing both Fishfinder and Chart or
Radar and Radar Repeater functionality.
Integrated System
Additional instruments are connected via hsb2,
SeaTalk or NMEA interfaces.
hsb2
High Speed Bus- links up to ten compatible display units. For full display and control between
hsb2 Plus Series display units, the units must be
connected via hsb2 and SeaTalk.
Introduction
Appendix C defines the chart features shown on the chart display.
1-4
hsb2 Plus Series Fishfinders
General
General
The hsb2 Plus Series Fishfinder system, illustrated below, is comprised of the
7" or 10.4" LCD display unit, fishfinder transducer, and associated cables.
D4866-2
Figure 1-1:
Basic Fishfinder System
Display Unit
The hsb2 Plus Series LCD display unit is waterproof to CFR46 and can be
installed either above or below deck.
The unit includes:
• 7" or 10.4" LCD display
• Trackpad
• Eleven dedicated (labeled) control keys
• Four soft keys (unlabeled) whose functionality changes
• Two slots for the C-MAP NT® or NT+ chart cards (Raychart models only)
The display and keys can be illuminated for night-time use.
Transducer
The hsb2 Plus Series Fishfinders require a transducer, either thru-hull, in-hull,
or transom-mount.
Transducers can measure water depth, temperature, distance traveled, and/or
speed. It is important to position your transducer correctly. For details on
transducers, including location and installation instructions, see document
number 81196, Transducers for Fishfinders Owner’s Handbook.
Note: If speed and temperature are being input via SeaTalk, these values are
displayed instead of the speed and temperature inputs from the transducer.
Chapter 1: Overview
1-5
The hsb2 (High Speed Bus) connection enables transfer of data among
compatible units. For example, fishfinder data is transferred from the
fishfinder (the master display) via the hsb2 connection and can be displayed
and controlled on any other hsb2 Plus Series LCD or CRT display (the repeater
display). However, if you change, say, depth range on one display, it affects all
displays showing fishfinder or fishfinder/chart overlay.
In particular, you can connect your hsb2 Series Plus Fishfinder to a remote hsb2
Series Pathfinder Plus Radar and then to a remote hsb2 Series Plus Chartplotter
to provide fishfinder, chart, and radar functionality on all three displays.
Full functionality of the fishfinder is achieved when it is part of an integrated
system, with other equipment (in addition to other hsb2 Plus units) connected
via SeaTalk or NMEA 0183. Data from this equipment including position and
heading is displayed on the display and is used in calculations.
It is possible to connect up to ten hsb2 Plus Series LCD or CRT displays to
provide an integrated system. Earlier HSB (non-Plus) Display units can be
upgraded to provide hsb2 compatibility. See Connecting hsb2 Plus Series
Displays on page 2-20 for details.
Note: Please contact Raymarine Customer Service or your authorized Raymarine dealer about upgrading your existing HSB (non-Plus) display units to
provide full hsb2 Plus functionality.
The hsb2 system can include several chartplotter displays, each with two chart
cartridge slots. Each display can access two local and up to six remote chart
cartridges. Charts can be controlled independently on each display, even when
a remote chart cartridge is being used. Details on connecting the equipment
are given in Chapter 2.
Display Unit Features
Fishfinder
• Displays depth, speed, and temperature, if the transducer is so equipped
• Dual or split frequency fishfinder display – 50 kHz, 200 kHz
• Display options – fishfinder window, zoom, bottom lock and A-Scope
• Uses position data from GPS, DGPS, WAAS or Loran-C technology
• Displays and transfers hsb2, SeaTalk and NMEA data
• Provides full control of data from other hsb2 instruments
• Half-screen windows to display additional data: depth/temperature graph,
Course Deviation Indicator (CDI), Bearing and Distance Indicator (BDI),
navigation data
Introduction to
hsb2 Systems
Introduction to hsb2 Systems
1-6
hsb2 Plus Series Fishfinders
Operating Modes
Chartplotter
• Displays information from the C-MAP NT® and NT+ chart cards
(C-Cards)
• Three full-screen operating modes: Fishfinder, Chart, Data Log (if appropriate data is available)
• View fishfinder and chart simultaneously
• Choice of chart orientation: Head Up, Course Up and North Up
Operating Modes
If you have a combined Fishfinder/Chartplotter unit, or have an hsb2 Plus
Series Chartplotter connected to a Fishfinder, three full-screen modes –
fishfinder, chart and data log are available; you select the operating mode
using the DISPLAY key as described in Chapter 3.
You can also set Windows On to split the display into two half-screen windows
to show supplementary data, or to display fishfinder and chart simultaneously.
The main operating mode (fishfinder or chart) is displayed in the upper
window; you choose what is displayed in the lower window.
In addition, if you have an hsb2 Series Pathfinder Plus Radar display
connected, you can set the display to radar mode; this provides similar
functionality to a combined Pathfinder Radar/Chartplotter.
If you only have an L760 Plus or L1250 Plus fishfinder-only unit connected,
only fishfinder mode is available.
1-7
Half -Screen Window Options
The following information, if available on your system, can be shown:
Table 1-1:
Window Options for Combined/Integrated Systems
Full-screen
mode
Half-screen Window Options Fishfinder/Chart Display only
Half-screen Window Options Fish/Chart + Radar Displays
Fishfinder Mode
Depth/temp, Chart, CDI, BDI, or Data
Depth/temp, Chart or CDI, BDI
Chart Mode
CDI, BDI, Nav Data or Fishfinder
CDI, BDI, Nav Data, Fishfinder or
Radar
Radar Mode
Not Available
CDI, BDI, Chart or Nav Data
Data Log Mode
Half-screen Windows not available
Windows not available
• Chart display (when in Fishfinder or Radar mode)
Fishfinder display (when in Chart mode):
Radar display (when in Chart mode):
If data is available, either as a function of the combined display unit or via
the hsb2 link, it can be displayed.
• Depth/temp graph (Fishfinder mode): This shows a plot water temperature and depth against time.
• Data (Fishfinder mode): This option splits the fishfinder vertically. The
left hand window displays data boxes; there are three different sets of data
(A, B and C) that you can select for display.
• CDI: This gives the Course Deviation Indicator graphical display, with
data relating to the target waypoint.
• BDI: This gives the Bearing and Distance Indicator graphical display, with
data relating to the target waypoint.
• Nav Data (Chart mode): This shows sixteen data boxes, providing navigational data in the units specified in your set up. Note that up to 6 of these
data boxes are also available as a user-selectable group (see Section 7.3).
For details on the radar, refer to the Owner’s Handbook supplied with your
radar.
Note: MARPA functionality is available on the fishfinder display if you have
an integrated system with a Pathfinder radar master display that includes
MARPA as a primary function.
Details on selecting windows are given in Chapter 3.
Operating Modes
Chapter 1: Overview
1-8
hsb2 Plus Series Fishfinders
The Fishfinder
Display
1.2 The Fishfinder Display
When you first turn the display unit on and select fishfinder mode, the
scrolling bottom graph is displayed. This is a graphical representation of the
echoes seen by the Fishfinder. As time passes, this display scrolls from right to
left and becomes a record of the echoes seen. A typical display is shown in
Figure 1-2.
The images at the right hand side of the display are the most recent echoes.
Some echoes indicate fish, and others show the bottom. It can also indicate
bottom structures, such as a reef or shipwreck. The upper and lower depth
range limits are shown.
The fishfinder screen includes a status bar that displays transducer frequency
and indicates which auto settings are enabled (Gain, Color Gain, Range,
Zoom and Frequency), and alarm status (fish and shallow/deep water depths).
You can customize the fishfinder by choosing what is displayed and how it is
displayed (including language and units). For example, you can set the scroll
speed of the bottom graph display, and you can select the range to adjust the
amount of detail displayed.
You can view the cursor position and a variety of data (such as speed, heading
and depth) from the transducer and other equipment in user-selectable data
boxes. These data boxes can be moved around the screen and they can be
switched on or off.
Chapter 3 includes details on adjusting the display, other set up options are
described in Section 7.3 and Section 7.4.
1-9
"#
!
$
%# &
50kHz
AUTO GCRZFH
SD
0
8
25
38
45
52
50
75
100
ft
FREQUENCY
ZOOM
BTM.LOCK
A-SCOPE
Figure 1-2:
Typical Fishfinder Display
Fishfinder Options
The fishfinder provides controls to select additional modes:
• Frequency – you can select the transducer frequency, 50 kHz for wide coverage and deep water, 200 kHz for a detailed view, both frequencies simultaneously or auto-frequency. The default setting is auto-frequency, which
determines the optimum frequency of operation based on the current
depth.
• Bottom Lock – changes the operating mode to re-set the bottom. It provides a bottom-up view: the bottom is used as the reference, its image is
flattened and depths are displayed here. Bottom lock mode is used primarily to filter-out the bottom structure and display fish details only.
Fishfinder Options
Chapter 1: Overview
1-10
hsb2 Plus Series Fishfinders
Fishfinder
Functions
• A-Scope – displays a real-time image of the bottom structure and fish
directly below the transducer. The A-Scope window also displays the patented Bottom Coverage width indication.
• Zoom – enlarges all or part of the bottom graph display. You can select x2,
x4 or x6 magnification and the zoom area can be automatically or manually adjusted.
You can select Zoom, Bottom Lock or A-Scope to be vertically split with the
bottom graph display. Alternatively, Zoom or Bottom Lock can be displayed
in place of the bottom graph display.
If you choose dual frequency, the scrolling bottom graph is displayed in both
frequencies, split horizontally. Zoom, Bottom Lock or A-Scope can be
displayed with the dual frequency graph.
All of these options are available when the fishfinder is displayed in a halfscreen window.
Fishfinder Functions
The hsb2 Plus Series Fishfinder includes the following functions:
• Automatic or manual selection of scroll speed for bottom graph display
• Automatic or manual selection of transducer frequency
• Automatic or manual selection of upper and lower depth range limits
• Adjustment of foreground/background color and image color threshold
(contrast control on the L755RC Plus monochrome display)
• Adjustment of Gain, Color Gain and STC
• Set up alarms for Fish, Shallow water and Deep water
• VRM marker to determine depth and distance
• Add marks to record important or dangerous locations
• Man Overboard (MOB) to navigate back to a person or object
Operation of these fishfinder functions is described in Chapter 3 and
Chapter 4.
Chapter 1: Overview
1-11
SPLIT
AUTO G Z
SPLIT
0
25
35
25
35
50
75
75
0
100
200kHz
50kHz
BTM.LOCK
ZOOM
50
75
75
A-SCOPE
AUTO G Z
25
50
100
ft
FREQUENCY
25
35
25
100
ft
FREQUENCY
7.9
0
25
35
25
50
100
200kHz
50kHz
0
25
Fishfinder
Functions
AUTO G Z
ZOOM
BTM.LOCK
52.3
A-SCOPE
200kHz
AUTO G
SPLIT
0
0
25
20
20
50
75
15
40
200kHz
50kHz
100
0
10
6
5
BL
25
60
50
X4
75
80
ft
FREQUENCY
ZOOM
BTM.LOCK
A-SCOPE
Figure 1-3:
Fishfinder Display Options
100
ft
FREQUENCY
ZOOM
BTM.LOCK
A-SCOPE
1-12
hsb2 Plus Series Fishfinders
The Chartplotter
Display
1.3 The Chartplotter Display
The L755RC, L760RC and L1250RC Plus Fishfinders include a Chartplotter.
The chartplotter includes a small-scale world map and detailed navigation
information is displayed when a cartographic chart card is installed. The
details displayed depend on the chart zoom level selected. A plotter mode is
provided to enable route plotting and tracking at large scales even when a chart
card is not installed A typical chartplotter screen is shown in Figure 1-4.
Note: For an L760 Plus or L1250 Plus fishfinder-only unit to have access to
chartplotter functionality, it must be connected to an hsb2 Plus Series Chartplotter device. This is discussed fully in the section Integrated Systems on
page 2-18.
The chartplotter uses position information from a GPS, DGPS, WAAS, or
Loran-C instrument. Once the position fix has been established, your vessel’s
position, if on screen, is shown as a boat shape pointing in the direction of the
current heading (or COG if heading data is not available). If no heading or
COG data is available, the vessel is shown as a circle.
The chartplotter screen includes a status bar that displays chart scale, with
either cursor position, range and bearing or, when the cursor is homed to the
vessel (by pressing FIND SHIP), vessel position, Speed Over Ground (SOG),
Course Over Ground (COG) and fix type (VES POS, DIF FIX or SD FIX).
The status bar also indicates if radar/chart overlay is switched on.
Any waypoints you have placed are displayed (unless you turned them off in
Chart Set Up as described in Chapter 7) and the current route is shown.
Information can be viewed on-screen by positioning the cursor over a
waypoint, current route or chart object. The chartplotter screen can also show
additional information, depending on your currently selected options, set up
selections and data available from other equipment.
An example chart display, in its default configuration, with a chart card
installed, is shown in the following illustration.
Several functions are available to control the display as follows:
• Zoom in/out and Pan the Display
• Offset the Chart or Center the Chart around the Vessel
• Overlay Radar Targets onto the Chart Display
• Synchronize the Chart and Radar (if radar data is available)
Operation of these functions is described in Chapter 3.
1-13
Chartplotter Display Options
Set up options allow you to customize the chart by choosing what is displayed
(including cartographic features), how it is displayed (including language and
units), heading mode and how the chartplotter operates with other hsb2 units.
You can also view the cursor position and a variety of data from other
equipment (for example, speed, heading, depth, wind, and tide information) in
a set of user-selectable data boxes. The cursor box and user-selected data
boxes can be moved around the screen and they can be turned on or off. You
can also obtain autopilot status and locked heading information.
Display options are provided in System Set Up and Chart Set Up as described
in Chapter 7. Chart set up options allow you to customize the chart by
selecting:
• What cartographic features and level of detail are displayed
• The chart color palette (shade or sunlight)
• Chart orientation (north up, head up or course up), datums and position offset
• How waypoints are displayed (symbols and numbers) and how chart
object information is displayed
• Vectors for heading, COG and tide
In addition Screen Presentation Options, described in Chapter 3 are provided
to switch:
• Cursor Box and Databoxes On/Off
• Chart Grid On/Off
• Custom Chart Details On/Off
Note: When you turn the display off and on again, these settings are retained
in memory.
Chartplotter
Display Options
Chapter 1: Overview
1-14
hsb2 Plus Series Fishfinders
Chartplotter
Display Options
Status Bar
Chart Range
Chart Boundary
Vessel Position
Waypoint
Cursor selecting chart object
Depth Area
Cursor position box
Shows the current
cursor position as
either Range/Bearing
or Lat/Long. You can
move this box to your
preferred position on
the screen or turn it off.
Object data box for object selected
by cursor
Default soft key labels
These can be turned off: press any soft key to redisplay them.
Different labels are displayed when you press a key.
D4275-3
Figure 1-4:
Typical Chartplotter Display
Custom Chart Details
The chartplotter set up options include a sub-menu to customize the
cartographic features. This menu allows you to switch features On, Off, or
control them using the CUSTOM soft key. The factory default settings for the
Custom chart options are as follows:
ON:
Chart text, chart boundaries, depth contours, navigation marks
and land features.
OFF:
Caution and routing data.
CUSTOM: Spot sounding, light sectors, marine features.
Note: The factory default for the CUSTOM settings is ON.
Icons are displayed in detail, depth shading limit is 10 m and depth contour
display is 0-100 m.
A complete list of chart features is given in Appendix C.
Chapter 1: Overview
1-15
The hsb2 Plus Series Chartplotter includes the following functions:
• Display C-MAP NT and NT+ C-Card chart information including Ports
and Tides (if available)
• View chart information (if available) for the Nearest Port
• Place, Move, Erase and Edit a Waypoint
• Goto Waypoint or Cursor
• Create, Save, Name, Edit and Follow a Route
• Review Route and Waypoint Lists
• Display vessel’s track; Save and Name the Track for re-call to screen
• Measure Chart Distances and Bearings on-screen
• Set Up Alarms and Timers
• Man OverBoard (MOB) to navigate back to a missing person or object
• Differential GPS set up page
Operation of these functions is described in Chapter 5 and Chapter 6.
Chartplotter
Functions
Chartplotter Functions
1-16
hsb2 Plus Series Fishfinders
You operate the fishfinder and chart systems using a variety of controls:
• A trackpad providing up, down, left, right and diagonal control of an on
screen cursor
• Eleven dedicated (labeled) control keys
• Four soft keys with labels displayed on the screen
• Pop-up menus, displayed on-screen, from which you select options
• Database lists, displayed on-screen, which enable you to edit items
Note: The cursor is the cross-hair symbol (+) visible on the display. You move
the cursor using the trackpad and use it to select a position or item on the
chart.
The control keys are shown in Figure 1-6. They are back-lit for night-time use
when the display brightness is dimmed. When you use a control, a help
message is displayed at the top of the screen (unless you switch help off as
described in Chapter 7). The following paragraphs describe the controls and
on-screen facilities.
Dedicated
keys
Trackpad
D3596-4
Operating Controls
1.4 Operating Controls
Soft keys
Dedicated keys
Figure 1-5:
7" LCD Display Control Keys
1-17
Dedicated
keys
D5440-1
Trackpad
Soft keys
Dedicated keys
Figure 1-6:
10.4" LCD Display Control Keys
Trackpad and Cursor
The trackpad has several functions:
• To move the cursor around the screen
• To select an item from a pop-up menu
• To adjust a variable soft key control
The cursor is used to:
• Select a position on the screen
• Select an item, for example, chart object on the chartplotter
• Pan the chart display
Moving the Cursor
You can press on any of the four sections of the trackpad to move the cursor in
that direction (up, down, left or right), or press two sections at the same time to
move diagonally. The cursor moves faster as you continue to press the
trackpad. The current cursor position is shown in the cursor data box (if
selected).
Trackpad and
Cursor
Chapter 1: Overview
1-18
hsb2 Plus Series Fishfinders
Trackpad and
Cursor
Note: During many operations you cannot move the cursor around the
screen; if you cannot move the cursor using the trackpad, check the default
soft keys are displayed (unless they have been switched OFF in system set up).
If not, press ENTER until they are displayed.
The cursor is normally displayed as a crosshair. However, in chart mode, if
you have not moved the cursor for more than five seconds, when you next
move it the cursor is outlined by a circle so it is easier to locate on the screen.
Context-Sensitive Cursor Control
The cursor is context-sensitive. When the cursor is positioned over special
features on the display a text label appears to identify the feature as follows:
Table 1-2:
Context-Sensitive Cursor Text Labels
Text Label
Feature
Fishfinder/Chart
BOX
Data box (any type)
Both
MOB
Man Over Board marker
Both
WPT
Waypoint
Both
BL
Bottom Lock
Fishfinder
VRM
Variable Range Marker
Fishfinder
ZOOM
Zoom
Fishfinder
A➟ B
Ruler line
Chart
COG
Course Over Ground vector
Chart
HDG
Heading vector
Chart
POS
Vessel’s position
Chart
RTE
Route leg
Chart
TIDE
Tide vector
Chart
Chart Icons
Various
Chart
Some items on the fishfinder/chartplotter screen, such as the cursor have
information associated with them. Most information is displayed in a data
box. The context-sensitive cursor allows you to move databoxes. In the case of
Fishfinder VRM data, depth is displayed on the right hand side of the
horizontal indicator, and distance is displayed at the top of the vertical
indicator.
1-19
Dedicated Keys
The dedicated keys: DISPLAY, MARKS, GAIN, VRM/EBL, MULTI,
ALARMS, RANGE, ENTER, CLEAR, MENU and POWER have fixed
functions; the functions are similar on all hsb2 Plus Series displays. For
example, ALARMS is used to set up the system alarms on both a fishfinder and
a chartplotter.
Some keys can be used in two ways:
• Press: Press the key momentarily and then release it. This method is used
for most key operations.
• Press and hold: Press the key and hold it down for the length of time stated
(for example, 3 seconds), and then release it.
When you press a dedicated key, one of the following happens:
i. The associated operation is performed, e.g., change chart scale
(RANGE).
ii. A pop-up menu is displayed, providing further options.
iii. A set of soft keys is displayed, providing further functions.
As you press a key, a single audio beep confirms the key action. If the keypress is not valid for the current screen or mode, three rapid beeps sound to
indicate that no response is available. If required, you can turn the key beeps
off as part of your set up procedure (see Chapter 7).
Soft Keys
The four keys below the screen are called soft keys because their functions
change according to the operation. The soft keys are grouped into related sets
and subsets providing access to the various functions. The soft key labels are
displayed on the screen just above the keys. The default soft keys are displayed
until you press a key, or select an item on the screen; the soft keys associated
with the action are then displayed.
FREQUENCY
ZOOM
MORE¬
CHRT SNR
D5013-1
The currently-selected soft key option is shown by its green background (gray
for the L755RC Plus monochrome display). If the key text is displayed in gray
rather than in black, it is not currently available.
When you press a soft key one of the following happens:
i. The associated operation is performed, e.g., 50 kHz.
ii. A sub-set of soft keys is displayed, providing further functions.
Dedicated Keys
Chapter 1: Overview
1-20
hsb2 Plus Series Fishfinders
iii. A pop-up menu is displayed, providing further options.
Pop-Up Menus
As with dedicated keys, when you press a soft key a single audio beep
confirms the key action. If the key-press is not valid for the current screen or
mode, three rapid beeps sound to indicate that no response is available. If
required, you can turn the key beeps off as part of your set up procedure (see
Chapter 7).
Pop-Up Menus
Pop-up menus usually provide set up options. When a pop-up menu is onscreen, a set of associated soft keys is also displayed as shown in Figure 1-7.
ALARMS SET UP
ARRIVAL ALARM
0.01nm
OFF TRACK ALARM
ON
ANCHOR ALARM
OFF
GROUNDING ALARM
5M/1.0nm
COUNTDOWN TIMER
00:33:00
ALARM CLOCK
OFF
SELECT ARRIVAL
ALARM RADIUS
D4265-4
Figure 1-7:
Typical Pop-up Menu
You use the trackpad to select an option from the menu, then use the
appropriate soft key to set the option. For example, you can toggle the OFF
TRACK ALARM on/off.
Chapter 1: Overview
1-21
The waypoints, routes and tracks that you create on the chartplotter are stored
in database lists. You can view these lists and select items for editing.
WAYPOINT LIST
SYMBOL
NAME
WAYPOINT 001
WAYPOINT 002
WAYPOINT 003
WAYPOINT 004
WAYPOINT 005
POSITION
BRG _186°
TEMP
DATE
GOTO
WAYPOINT
---°C
--/--/--
EDIT
WAYPOINT
50°21^966N
001°20^368W
RNG _21.0nm
DEPTH
TIME
---m
--:--:--
MAKE NEW
WAYPOINT
WAYPOINT
TRANSFER
D4262-2
Figure 1-8:
Typical Database List
As with pop-up menus, when a database list is on-screen, a set of associated
soft keys is also displayed; you use the trackpad to select an item from the list,
then use the appropriate soft key to edit the item. For example, you can erase a
waypoint or a route.
Database Lists
Database Lists
1-22
hsb2 Plus Series Fishfinders
Database Lists
Chapter 2: Installation
2-1
Chapter 2: Installation
This chapter provides installation instructions for the hsb2 Plus Series
Fishfinders. Simple systems such as that in Figure 2-1 below, or integrated
systems such as that in Figure 2-2 are explained (see Section 2.7). Details for
mounting the hsb2 Plus Series LCD Display and connecting the equipment are
included.
Fishfinder Display
GPS
Transducer
Junction
Box
Compass
SeaTalk
NMEA
12/24V Supply
12V Supply
Figure 2-1:
Typical Fishfinder System
D5441-3
Distribution Panel
12V Supply
Introduction
2.1 Introduction
2-2
hsb2 Plus Series Fishfinders
hsb2 Series Master Display
GPS
hsb2 Series Repeater Display
Introduction
Transducer
Compass
HSB
SeaTalk
Distribution Panel
Junction
Box
12/24V Supply
12V Supply
Figure 2-2:
D5442-3
NMEA
12V Supply
Fishfinder in an Integrated System
Note: If you wish to practice using the display before installation, use the simulator mode, as described in Chapter 3. For power, connect a 12V or 24V DC
power supply, attaching the red wire via a quick blow fuse (6A for 12V or 4A
for 24V) to positive and the black wire to negative.
If you are connecting your display to other equipment (including another hsb2
Plus Series display unit) install then test the fishfinder display and transducer
as described in this chapter. Once the display is operating correctly, you can
connect it to other equipment as described in Section 2.7Integrated Systems
on page 2-18, taking particular care to ensure the correct polarity of the
SeaTalk supply. Section 2.7 describes the hsb2, SeaTalk and NMEA
interfaces.
For the Fishfinder to display depth, water temperature and speed, you must
install the Depth/Speed/Temp transducer supplied with your system.
For full functionality of the radar and chartplotter you need to provide position
and heading data.
• Heading data enables the chart to operate in North Up and Course Up
modes. If speed data is also available the MOB function operates.
• Position data is required for full functionality of the chart display.
Chapter 2: Installation
2-3
Full details of heading, position and other data are given in Section 2.7.
Planning the Installation
• Correct transducer for your application. See document number 81196,
Transducers for Fishfinders Owner’s Handbook.
• Location of the display unit, as described in Section 2.3
• Cable Runs, including cables for an integrated system (to provide heading
and position data, etc.), as described in Section 2.4.
EMC Installation Guidelines
All Raymarine equipment and accessories are designed to the best industry
standards for use in the recreational marine environment.
Their design and manufacture conforms to the appropriate Electromagnetic
Compatibility (EMC) standards, but correct installation is required to ensure
that performance is not compromised. Although every effort has been taken to
ensure that they will perform under all conditions, it is important to understand
what factors could affect the operation of the product.
The guidelines given here describe the conditions for optimum EMC
performance, but it is recognized that it may not be possible to meet all of these
conditions in all situations. To ensure the best possible conditions for EMC
performance within the constraints imposed by any location, always ensure
the maximum separation possible between different items of electrical
equipment.
For optimum EMC performance, it is recommended that wherever possible:
• Raymarine equipment and cables connected to it are:
• At least 3 ft (1 m) from any equipment transmitting or cables carrying
radio signals, e.g., VHF radios, cables and antennas. In the case of SSB
radios, the distance should be increased to 7 ft (2 m).
• More than 7 ft (2 m) from the path of a radar beam. A radar beam can
normally be assumed to spread 20 degrees above and below the radiating element.
• The equipment is supplied from a separate battery from that used for
engine start. Voltage drops below 10 V, and starter motor transients, can
cause the equipment to reset. This will not damage the equipment, but may
cause the loss of some information and may change the operating mode.
• Raymarine specified cables are used. Cutting and rejoining these cables
can compromise EMC performance and must be avoided unless doing so
is detailed in the installation manual.
Planning the
Installation
Before you install your system, plan the installation, considering:
2-4
hsb2 Plus Series Fishfinders
• If a suppression ferrite is attached to a cable, this ferrite should not be
removed. If the ferrite needs to be removed during installation it must be
reassembled in the same position.
EMC Installation
Guidelines
Suppression Ferrites
The following illustration shows typical cable suppression ferrites used with
Raymarine equipment. Always use the ferrites supplied by Raymarine.
D3548-3
Figure 2-3:
Typical Suppression Ferrites
Connections to Other Equipment
If your Raymarine equipment is to be connected to other equipment using a
cable not supplied by Raymarine, a suppression ferrite MUST always be
attached to the cable near to the Raymarine unit.
Chapter 2: Installation
2-5
2.2 Unpacking and Inspecting the Components
Check that you have all the correct system components. These depend on your
system package, as follows:
Table 2-1:
Parts and Accessories
Item
Part No.
Supplied with:
Option for:
7” Monochrome Fishfinder/Chartplotter
7” Color LCD Fishfinder
7” Color LCD Fishfinder/ChartplotterS
10.4” Color LCD Fishfinder
10.4” Color LCD Fishfinder/Chartplotter
E63007
E63019
E63010
E63013
E63014
L755RC Plus
L760 Plus
L760RC Plus
L1250 Plus
L1250RC Plus
—
—
—
—
—
7” LCD Display Sun cover
10.4” LCD Display Sun cover
D331
E55031
L755RC, L760, L760RC
L1250, L1250RC
—
—
Handbook, Fishfinder/Chart
Quick Reference Card, Fishfinder
Quick Reference Card, Chart
81195
86066
86067
All
All
L755RC, L760RC,
L1250RC
—
—
—
Mounting bracket knobs (x2)
7” Display Mounting bracket assy
10.4” Display Mounting bracket assy
7” Display Flush Mount Kit
10.4” DIsplay Flush Mount Kit
W145
W143
E55032
M92708
E55033
All
L755RC, L760, L760RC
L1250, L1250RC
—
—
—
—
—
L755RC, L760, L760RC
L1250, L1250RC
Power cable
SeaTalk cable assembly Flat moulded plugs both ends:
3 ft 3 in (1 m) long
9 ft 9 in (3 m) long
16 ft 3 in (5 m) long
29 ft 3 in (9 m)) long
Flat to male round connector:
12 in (0.3 m) long
Flat to female round connector:
12 in (0.3 m) long
Flat moulded plug one end only:
3 ft 3 in (1 m) long
SeaTalk auxiliary junction box
W144
All
—
D284
D285
D286
D287
—
—
—
—
All
All
All
All
D187
—
All
D188
—
All
D229
R55006
—
All
All
—
Unpacking and
Inspecting the
Components
Unpack your system carefully, to prevent damage to the equipment. Save the
carton and packing, in case you need to return a unit for service.
2-6
hsb2 Plus Series Fishfinders
Table 2-1:
Parts and Accessories
Item
Part No.
Supplied with:
Option for:
3 ft 3 in (1 m)
10 ft (3 m)
20 ft (6 m)
30 ft (10 m)
60 ft (20m)
hsb2 In Line Terminator
hsb2 Splitter Cable
NMEA OUT cable assy
4 ft 11 in (1.5m)
R55001
R55002
R55003
R55004
E55010
R58117
E55040
—
—
—
—
—
All
—
All
All
All
All
All
—
All
R55005
All
—
Transducer and Cables (See 81196
—
—
—
hsb2 cable assy
Unpacking and
Inspecting the
Components
Transducers for Fishfinders Handbook)
Chapter 2: Installation
2-7
2.3 Selecting the Equipment Location
The display unit can be mounted using the mounting bracket supplied, or
console mounted using the optional flush-mounting kit. The dimensions of the
display units, including the bracket, are shown below in Figure 2-4,
Figure 2-5 and Figure 2-6.
When planning the display installation, the following should be considered to
ensure reliable and trouble free operation:
• Convenience: The contrast and colors seen on all LCD displays vary
slightly with viewing angle; this is more noticeable on the left hand side.
Power the unit and select a suitable mounting location prior to installing
the display. The mounting location should be easily accessible to allow
operation of the front panel controls.
• Access: There must be sufficient space behind the display to allow cable
connections to the rear panel connectors, avoiding tight bends in the cable.
• Interference: The selected location should be far enough away from
devices that may cause interference, such as motors, generators and radio
transmitter/receivers (see the EMC guidelines earlier in this section).
• Magnetic compass: Mount the display unit at least 3 ft (1m) away from a
magnetic compass.
• Cable runs: The display unit must be located near a DC power source. The
power cable supplied is 4.9 ft (1.5m), but a longer cable can be used if
required: refer to Section 2.4.
The maximum length of cable between a master display and the transducer unit should not normally exceed 30 ft (10 m). If you need to use a
longer cable, refer to Section 2.4.
• Environment: Do not restrict airflow at the rear of the display unit;
the display incorporates Cold Cathode Florescent Lamps (CCFL),
which have a reduced light output when the unit is very hot. Ventilation is required to prevent the unit from overheating.
The display should be protected from physical damage and excessive
vibration. Mount the display in a protected area away from prolonged and
direct exposure to rain and salt spray.
Selecting the
Equipment
Location
Display Unit Mounting Location
2-8
hsb2 Plus Series Fishfinders
*
0.95 in
(24.3 mm)
Display Unit
Mounting Location
0.4 in
(10 mm)
6.89 in (175 mm)
8.1 in (205.2 mm)
7.3 in (185 mm)
10.51 in (267 mm)
8.8 in (223.6 mm)
GAIN
DISPLAY
VRM/EBL
MARKS
RANGE
ALARMS
ENTER
POWER
8.5 in (217 mm)
MULTI
CLEAR
MENU
2.1 in
(53.5 mm)
1.3 in
(33.5 mm)
1.42 in (36 mm)
3.15 in
(80 mm)
6.3 in (160 mm)
4.53 in (115 mm)
6.9 in (176 mm)
cable cleareance
Weight: 8.1 lbs (3.7 Kg)
1.28 in (32.5 mm)
Compass Safe Distance: 39 in (1 m)
8.85 in (225 mm)
D4847-4
Figure 2-4:
7” Color LCD Fishfinder Display Unit Dimensions
(L760 Plus and L760RC Plus)
Chapter 2: Installation
2-9
0.95 in
(24 mm)
0.4 in
(9.5 mm)
6.89 in (175 mm)
0.4 in
(9.5 mm)
8 in (204 mm)
7.3 in (185 mm)
10.54 in (267.7 mm)
8.76 in (222.5 mm)
GAIN
DISPLAY
VRM/EBL
MARKS
RANGE
ALARMS
ENTER
POWER
8.5 in (216 mm)
MULTI
CLEAR
MENU
3.2 in (81 mm)
3.15 in
(80 mm)
3.15 in
(80 mm)
2.16 in
(55 mm)
1.3 in
(33.5 mm)
1.45 in (37 mm)
6.9 in (176 mm)
cable cleareance
Weight: 7.5 lbs (3.415 Kg)
6.3 in (160 mm)
Compass Safe Distance: 39 in (1 m)
8.85 in (225 mm)
D5071-2
Figure 2-5:
7” Monochrome LCD Fishfinder Display Unit Dimensions
(L755RC Plus)
Display Unit
Mounting Location
0.95 in
(24 mm)
2-10
hsb2 Plus Series Fishfinders
3.82 in (97 mm)
11.5 in (292 mm)
12.3 in (313 mm)
11.4 in (289 mm)
Display Unit
Mounting Location
1.65 in
(42 mm)
6.38 in (162 mm)
cable clearance
0.28 in
(7.1 mm)
10.83 in (275 mm)
12.9 in (328 mm)
7.88 in (200 mm)
3.94 in (100 mm)
0.87 in (22.1 mm)
3.15 in
(80 mm)
9.7 in (246 mm)
1.7 in (43 mm)
Compass Safe Distance: 39 in (1 m)
11.26 in (286 mm)
D5066-3
Figure 2-6:
10.4” Color LCD Fishfinder Display Dimensions
(L1250 and L1250RC Plus)
Chapter 2: Installation
2-11
2.4 Cable Runs
• You need to attach the power cable and the transducer cable. Additional
cables will be required if you are installing an integrated system.
• All cables should be adequately secured, protected from physical damage
and protected from exposure to heat. Avoid running cables through bilges
or doorways, or close to moving or hot objects.
• Acute bends must be avoided
• Where a cable passes through an exposed bulkhead or deckhead, a watertight feed-through should be used.
• Secure cables in place using tie-wraps or lacing twine. Coil any extra cable
and tie it out of the way.
You need to run the following cables:
• Power/NMEA Input cable, supplied with the display unit. This has a connector plug at one end for connecting the display unit, and 7 wires at the
other end for connecting the power supply and optional NMEA inputs (see
Integrated Systems on page 2-18).
• Transducer cable, supplied with the transducer. This 30 ft (10 m) cable
has a connector plug (with an outer nut that you must attach) at one end for
the display unit or extension cable.
• SeaTalk cable, optional, with SeaTalk connector(s) at one or both ends.
• HSB cable, optional.
• NMEA Output cable, optional, with an NMEA OUT connector at one
end only.
Power Cable
The hsb2 Plus Series Fishfinder is intended for use on ships’ DC power
systems rated from 10.7 V to 32 V.
A 5 ft (1.5 m) power cable is supplied for connecting the ship’s DC power to
the display unit. The power cable may be extended by up to 60 ft (20 m) using
a wire gauge of AWG 12 (3.5 mm2) or greater.
Transducer Cable
A 30 ft (10m) cable is supplied with the transducer. The transducer cable may
be extended up to a maximum of 60 ft (20 m) using optional extension cables.
For details, see document number 81196, Transducers for Fishfinders
Owner’s Handbook.
Cable Runs
Consider the following before installing the system cables:
2-12
hsb2 Plus Series Fishfinders
2.5 Mounting the Display Unit
Mounting the
Display Unit
The hsb2 Plus Series LCD display unit is waterproof to CFR46 and can be
installed either above or below deck. The display unit can be mounted using
the mounting bracket supplied, or console mounted using the optional flushmounting kit (see Section 2.2).
Mounting Bracket
The display unit can be mounted on a dash, chart table, bulkhead, or deckhead.
D4848-1
Figure 2-7:
LCD Display Mounting
1. Loosen the knobs and remove the mounting bracket from the display unit.
2. Mark the locations of the mounting bracket screw holes on the mounting
surface.
3. Use the screws supplied to attach the mounting bracket at the marked locations.
4. Attach the display unit to the mounting bracket, adjust the display angle,
and tighten the knobs.
Chapter 2: Installation
2-13
The display unit can be console mounted if required, using the optional flushmounting kit (Raymarine part number M92708 for 7” Fishfinder displays and
E55033 for 10.4” Fishfinder displays).
CAUTION:
Make sure there are no hidden electrical wires or other items behind the
location before proceeding. Make sure there is sufficient rear access for
mounting and cabling.
1. Check the selected location for the unit. A clear, flat area at least 9 in (230
mm) wide by 8¼ in (210 mm) high, with at least 6.9 in (176 mm) of clearance behind the panel, is required.
2. Unpack the flush-mounting kit.
3. Using the supplied template, trace out the display unit opening.
4. Drill a ½ in (12.7 mm) pilot hole in each corner of the cut-out area.
5. Using a suitable saw, cut along the inside edge of the cut-out line.
6. Remove the mounting bracket knobs and bracket from the display unit.
Make sure that the unit fits in the cut-out area.
If the optional screw fitting is required, drill four 3/16 in (5 mm) holes as
indicated on the template.
Screw the studs into the holes provided at the rear of the display.
7. Connect the DC power cable, transducer cable, and any other accessory
cables to the display. Avoid tight bends in the cables.
8. Place the gasket on the unit and slide the unit into the panel cut-out.
9. Use the flush-mounting kit to secure the unit to the console.
Alternatively, place a spacer over each of the four studs and secure with
the thumb nuts.
Mounting the
Display Unit
Console Mounting
2-14
hsb2 Plus Series Fishfinders
2.6 System Connections
Grounding the System
System
Connections
It is important that an effective RF ground is connected to the system. You
must ground the display by connecting the drain wire (shield) of the Power/
NMEA Input cable to the ship’s RF ground; a single ground point should be
used for all equipment.
If you need to extend the wire, the extension wire should be an 8 mm braid or
AWG 10 (6.0 mm2) multi-stranded cable.
If your vessel does not have an RF system, connect the drain wire to the
negative battery terminal.
DC Power Connection
The hsb2 Plus Series Fishfinder is intended for use on ships’ DC power
systems rated from 10.7 V to 32 V.
The power connection to the display should be made at either the output
of the battery isolator switch, or at a DC power distribution panel.
Raymarine recommends that power is fed directly to the display via its
own dedicated cable system and MUST be protected by a thermal circuit
breaker or fuse, installed close to the power connection.
Use a 6 amp fuse for 12V systems or 4 amp fuse for 24/32V systems.
The DC system should be either:
• Negative grounded, with the negative battery terminal connected to the
ships ground.
• Floating, with neither battery terminal connected to the ships ground.
CAUTION:
This system is not intended for use on “positive” ground vessels.
The power cable Ground (earth) connections must be connected to the
ship’s ground as described above.
Power for External Equipment
External equipment cannot be powered from the display’s SeaTalk
interface.
It must be powered from the ship’s supply or via a SeaTalk bus.
Refer to Section 2.7 for further details.
Chapter 2: Installation
2-15
Display Unit Connection
The rear of the hsb2 Plus Series LCD display provides the following
connection sockets:
• HSB, in/out connector for connecting to another hsb2 Plus Series display
(such as a chartplotter, radar, or second fishfinder display).
• SeaTalk, for SeaTalk data input and output and connecting to another hsb2
Plus Series display (such as a chartplotter, radar, or second fishfinder display).
•
NMEA Output, for NMEA data output in an integrated system.
• Power/NMEA Input, for 12 V, 24 V or 32 V DC power connection, two
NMEA 0183 inputs and one RF ground (screen) connection.
HSB
NMEA OUT
POWER/NMEA
SeaTalk
G R
TRANSDUCER
Y
D4849-2
Figure 2-8:
Fishfinder Display Connector Panel
The following sections detail the display unit connectors used when installing
a single hsb2 Plus Series LCD Display. The remaining connector details are
provided in Section 2.7.
Transducer Connection (master displays)
The transducer cable connector (and Y-shaped connector, if supplied) has a
nut that has been removed to aid installation. To allow you to complete the
installation without cutting the cable, ensure that any holes you drill are large
enough to accept the connector, with the nut removed (approximately 13/16"
or 21 mm).
Before attaching the transducer cable, you will need to attach the connector
nut and split ring. These items, plus a wedge tool, are included in the
transducer packaging.
The transducer cable is attached to the 7 pin male connector marked
TRANSDUCER on the rear of the display unit. How you connect the cable to the
display unit depends on the type of transducer you have installed:
Display Unit
Connection
• Transducer connection.
2-16
hsb2 Plus Series Fishfinders
• Combined depth/speed/temp transducers have a 7 pin female connector.
Attach the transducer cable connector directly to the display unit.
Display Unit
Connection
• Combined speed/temperature transducers have a 3 pin female connector
that requires the use of an additional Y-shaped cable (Raymarine part number E66022) to attach to the 7 pin connector on the display. This Y-cable is
included with your speed/temperature transducer.
Attach the 7 pin female connector on the Y-cable to the display unit then
attach the transducer cable to the 3 pin male connector on the Y-cable.
• Depth-only transducers have a 7 pin female connector.
Attach the transducer cable connector directly to the display unit.
or
If being installed in conjunction with a speed/temperature transducer,
attach the 7 pin female connector on theY-cable to the display then attach
the transducer cable to the 7 pin male connector on the Y-cable.
Note: If your system requires both a Y-cable and a transducer extension cable, ensure that you connect the Y-cable to the display unit and the extension
cable to the transducer.
The connector pins are shown in the following diagram, together with the
connections and wire colors; this is information is provided as an aid to fault
diagnosis.
CAUTION:
Do not cut the transducer cable or remove the connector. Do not try to
shorten or splice the cable. If the cable is cut, it cannot be repaired.
Cutting the cable will also void the warranty.
5
2
7
1
6
4
3
D4850-2
Pin No.
Function
Color
Pin No.
Function
Color
1
Speed
Red
5
Speed/Temp Ground
Brown
2
Temp
White
6
+ Depth
Blue
3
Shield
Drain
7
- Depth
Black
4
Sense
Green
Figure 2-9:
Fishfinder Transducer Connector
Chapter 2: Installation
2-17
The DC power and NMEA input should be connected at the rear Power/
NMEA seven-pin connector. The connector (viewed from the outside) and pin
functions are shown in the following diagram and table. The NMEA Input is
detailed in Section 2.7.
f
2
5
1
7
4
3
6
D3231-2
Pin No.
Function
Color
1
Channel 1 NMEA data input (+ve)
Orange
2
Channel 1 NMEA return (-ve)
Yellow
3
Battery negative
Black
4
Shield (drain wire)
No insulation
5
Battery positive (12/24/32 V systems)
Red
6
Channel 2 NMEA data input (+ve)
Green
7
Channel 2 NMEA return (-ve)
Blue
Figure 2-10: Power and NMEA Connector
Power Connection
CAUTION:
If the power connections are accidentally reversed the system will not
work. Use a multimeter to ensure that the input power leads are
connected for correct polarity.
Switch off the display unit before you remove the power cord.
The RED wire must be connected to the feed from the positive (+) battery
terminal and the BLACK wire to the feed from the negative (–) battery
terminal. The shielded wire (screen) should be connected to the ship’s RF
ground as previously described in Grounding the System on page 2-14.Any
unused wires should be insulated and taped back.
Display Unit
Connection
Power and NMEA Input Connection
2-18
hsb2 Plus Series Fishfinders
EMC Conformance
Always check the installation before going to sea to make sure that it is not
affected by radio transmissions, engine starting, etc.
EMC Conformance
2.7 Integrated Systems
The hsb2 Plus Series displays can be linked to other equipment to transfer data
as follows:
• A second display, either CRT or LCD, can be connected via hsb2 (and
SeaTalk) to repeat fishfinder, chart and/or radar information at a remote
location.
Note: If you have an integrated system with a Pathfinder Plus radar master
display that includes MARPA as a primary function, MARPA functionality is
available on the LCD repeater display.
• Data can be received via SeaTalk or NMEA, some of which will increase
the functionality of the display. Other data can be viewed on the display.
• Data can be transmitted via SeaTalk and NMEA to enhance other equipment.
• Some incoming data can be converted across the communication link and
re-transmitted.
Power for External Equipment
External equipment cannot be powered from the display’s SeaTalk
interface. It must be powered from the ship’s supply or via a SeaTalk bus.
Ensure correct polarity of the SeaTalk connection.
For systems where the ship’s power source is 24 V only, you may need to
install a 24 V to 12 V DC converter. This is only necessary if the products
being connected to the display are:
• SeaTalk compatible (for example, compass, GPS and instruments), and
there is no existing SeaTalk bus
• NMEA compatible, but operate only from 12 V (for example, compass,
GPS and some navigators)
The DC-DC converter must conform to the following specification:
Table 2-2:
DC-DC Converter for External Equipment
Input
21 to 32 V DC
Output
13.6 V DC, isolated
Load
Continuous current rating, in excess of required load
Chapter 2: Installation
2-19
The High Speed Bus (hsb2) provides extremely rapid transfer of data between
master and repeater displays. With an hsb2 and a SeaTalk connection, most
data available can be controlled and displayed by any unit.
Master functionality is provided by the display with the appropriate
transducer/scanner connected as defined in Table 2-3 . You can have a master
fishfinder and a master radar in the same system. Data on master units are
displayed on all connected repeater units.
Note: If the master display is an L1250 Plus or L1250RC Plus, repeater displays can take advantage of these units’ extended power (1000 watts vs. 600
watts RMS) and depth range (5000 feet vs. 3000 feet).
Up to ten hsb2 Plus Series displays can be combined to create a variety of
functionalities. For example, you can connect your hsb2 Series Plus Fishfinder
to a remote hsb2 Series Pathfinder Plus Radar and then to a remote hsb2 Series
Plus Chartplotter to provide fishfinder, chart, and radar functionality on all
three displays. You can display some combinations, such as fishfinder/chart or
radar/chart, in half-screen windows.
Note: Fishfinder STC cannot be adjusted on a repeater display, nor can depth
offset, speed and temperature calibration be set. Frequency can be selected on
either master or repeater, but the same frequency is used on all displays.
The hsb2 system can include several chartplotter displays, each with two chart
cartridge slots. Each display can access two local and up to six remote chart
cartridges. Charts can be controlled independently on each display, even when
a remote chart cartridge is being used.
Table 2-3:
hsb2 Plus Series Master Displays
Master Function
Plus Series Display Type
Transducer/Scanner
Radar
R70, RL70, RL70C, RL70RC, RL70CRC,
R80, RL80, RL80C, RL80RC, RL80CRC
Any Pathfinder Series
Scanner
Chart
RC520, RC530, RC631
RL70RC, RL70CRC, RL80RC, RL80CRC,
L755RC, L760RC, L1250RC
Display includes a two-slot
chart cartridge
Fishfinder
L755RC, L760, L760RC, L1250,
L1250RC
Fishfinder transducer
Note: Earlier HSB (non-Plus) Display units with can be upgraded to provide
hsb2 Plus compatibility. Please contact your authorized Raymarine dealer for
details.
High Speed Bus
(hsb2)
High Speed Bus (hsb2)
2-20
hsb2 Plus Series Fishfinders
RL80C PLUS Radar
L1250 PLUS Fishfinder
L760 PLUS Fishfinder
R
SeaTalk
G
Y
TRANSDUCER
NMEA OUT
HSB
POWER/NMEA
R
SeaTalk
G
Y
TRANSDUCER
NMEA OUT
POWER/NMEA
NMEA OUT
POWER/NMEA
R
HSB
G
SeaTalk
TRANSDUCER
Y
NMEA OUT
R
POWER/NMEA
HSB
G
SeaTalk
TRANSDUCER
Y
High Speed Bus
(hsb2)
HSB
RC530 PLUS Chartplotter
D5655-3
hsb2
Inline
Terminator
hsb2
Splitter
HSB cable
Power
hsb2
Inline
Terminator
hsb2
Splitter
HSB cable
Power
HSB cable
Power
Power
Figure 2-11: Fishfinder Integrated System with Multiple hsb2 Plus Connections
Upgrading Existing HSB Series Displays
Earlier HSB (non-PLUS) display units can be upgraded to provide hsb2 Plus
compatibility. Two types of upgrades are available:
1. A full hardware and software upgrade (Plus upgrade) provides full compatibility with the hsb2 system.
This configuration supports up to eight true Plus (or Plus upgraded) displays with a cable limit of 60 meters, or up to ten true Plus (or Plus
upgraded) displays at a maximum of 40 meters cable length.
2. A software-only upgrade enables the display to be used with a Plus (or Plus
upgraded) unit in the hsb2 system.
However, like the old HSB (non-Plus) system, this configuration only supports two displays: two software-only upgraded units, or one softwareonly upgraded with one true Plus (or Plus upgraded) display.
Connecting hsb2 Plus Series Displays
Figure 2-11 illustrates how to inter-connect various hsb2 Plus Series Displays.
When connecting your hsb2 Plus Series displays, there are several important
points to keep in mind:
1. If more than two hsb2 Plus Series displays are to be connected, you must
use an hsb2 Splitter Cable, Raymarine part number E55040.
2. hsb2 displays at the end of the chain must be terminated using the Inline
Terminator plug (Raymarine part number R58117) included with your hsb2
Plus Series display unit.
Chapter 2: Installation
2-21
4. Earlier HSB (non-Plus) Display units can be enhanced with a hardware
and software upgrade to provide full hsb2 Plus functionality.
5. Earlier non-Plus displays can also be outfitted with a software-only
upgrade, which enables hsb2 compatibility. However, these software-only
upgraded displays are not true Plus units. They must not use the Inline Terminator plug because they are already terminated internally.
Like the old HSB system, this configuration only supports two displays:
two software-only upgraded units, or one software-only upgraded with
one true Plus (or Plus upgraded) display.
An In/Out connector cable is provided for connecting to another hsb2 Plus
Series display.
Note: The HSB cables have ferrite clamps attached at each end to ensure
EMC conformance. The cables are available in lengths of 1, 3, 6, 10 and 20 m.
HSB connector
Pin 1, screen
Pin 3, blue
HSB connector
Pin
Pin name
Function
1
CGND
Screen
2
HSVB_POS
SeaTalk HSB
3
HSVB_NEG
SeaTalk HSB
Pin 2, white
1
Rear of Display Unit
HSB
2
3
D4253-3
Figure 2-12: HSB Connector
The display unit is supplied with a blanking plug. This should be attached to
the HSB cable port if the HSB port is not used. If the display unit is installed in
an exposed position, seal the blanking plate with silicon compound.
High Speed Bus
(hsb2)
3. The total cable length for an hsb2 network containing the maximum 10 display units (both Plus and Plus upgrades) must not exceed 40 meters. A network comprised of only 8 displays can extend up to 60 meters.
2-22
hsb2 Plus Series Fishfinders
SeaTalk and NMEA In
The hsb2 Plus Series display can receive a comprehensive range of data. The
primary data is described below:
SeaTalk and NMEA
In
Table 2-4:
Function of SeaTalk and NMEA Data
Data
Primary Uses
Suggested Source
Heading
Chart: modes/ vectors
Compass connected to SeaTalk bus,
NMEA Compass
Position
Chart: own vessel position
MOB (also requires speed and HDG
data)
SeaTalk GPS connected via Auxiliary JB
Existing GPS Navigator via SeaTalk bus
Existing GPS (or Loran-C) navigator with
NMEA output
Waypoint
Chart: Waypoint and route transfer
Existing GPS Navigator via SeaTalk bus
Existing GPS (or Loran-C) navigator with
NMEA output
Heading data should ideally contain both magnetic and true heading. If only
one is available then a source of magnetic variation should be connected.
Radars and chartplotters can exchange their cursors via SeaTalk. Locked
heading should be used for Course Up if available via SeaTalk. Other data
connected via a SeaTalk bus or via NMEA is generally displayed in data
boxes, e.g., depth, apparent wind angle and speed, time.
Note: The Fishfinder uses its own depth data, rather than any other depth data
on SeaTalk. If there is no other depth data on SeaTalk, Fishfinder depth is
transmitted. If speed and temperature data are available on SeaTalk the Fishfinder uses this data; if this data is not on SeaTalk from other instruments, it is
transmitted by the Fishfinder.
For details of received data refer to the table in Appendix D: SeaTalk and
NMEA Data. Examples of SeaTalk and NMEA systems are shown in
Figure 2-13 and Figure 2-14.
Chapter 2: Installation
2-23
Scanner
GPS
hsb2 Series Fishfinder
hsb2 Series Chartplotter
SeaTalk
SeaTalk and NMEA
In
SeaTalk
hsb2 Series Radar
SeaTalk
HSB
HSB
12/24V Supply
12/24V Supply
SeaTalk
Course Computer
SeaTalk
Transducer
SeaTalk
SeaTalk
Distribution Panel
12/24V
Supply
12/24V
Supply
12/24V Supply
12/24V Supply
D5578-2
Figure 2-13: Integrated System with Repeater Displays and SeaTalk Instruments
2-24
hsb2 Plus Series Fishfinders
hsb2 Series Repeater Display
hsb2 Series Fishfinder Display
SeaTalk and NMEA
In
Transducer
HSB
SeaTalk
GPS
Compass
NMEA Out
Distribution
Panel
Non SeaTalk
Pilot
NMEA
12/24V Supply
NMEA
12V Supply
D4868-3
Figure 2-14: Integrated System with Repeater Display and NMEA Instruments
SeaTalk
The SeaTalk standard was originally developed by Autohelm (part of the
Raymarine group), and allows compatible instruments to be connected by a
single cable carrying power and data in/out. This means that additional
instruments and functions can be added to a SeaTalk system, simply by
plugging them into the network.
SeaTalk is a precise, high-speed, bi-directional protocol which is flexible
enough to adapt to any number of instruments, without a central processor.
SeaTalk equipment can also communicate with non-SeaTalk equipment via
the NMEA standard.
SeaTalk Connection
SeaTalk data, if present, is the primary source for all navigational data except
heading.
This connection is necessary for full functionality between hsb2 Plus Series
displays.
Chapter 2: Installation
2-25
The SeaTalk input/output should be connected at the rear SeaTalk 3-pin
connector. This appears as follows, when viewed from outside:
1. Red (No internal connection)
2. Screen (0V)
3. Yellow (Data)
D3232-4
Figure 2-15: SeaTalk Connector
Table 2-5:
Sea Talk Connections
Pin No.
Function
Color
1
+12 V
Red
2
0V
Shield
3
Data
Yellow
Note:
1. The display does not supply 12 V via the SeaTalk connector, nor does the
SeaTalk connector require 12 V to operate.
12 V is required for other SeaTalk units (except where SeaTalk is connected only between two hsb2 displays).
2. If you are connecting an active compass to the fishfinder, the NMEA input
has priority. You should, therefore, use an NMEA input channel (see Power
and NMEA Input Connection) rather than the SeaTalk interface, unless the
compass only has a SeaTalk output.
To connect the display unit to the SeaTalk bus, connect a standard SeaTalk
cable between the SeaTalk connector on the rear of the display and a SeaTalk
instrument or the SeaTalk bus.
Standard SeaTalk cables are available in a range of lengths (part numbers
D284 to D287), and cables for connecting to SeaTalk units with round
connectors are also available (part numbers D187 or D188), see Section 2.2
for further details.
NMEA 0183
The NMEA 0183 Data Interface Standard was developed by the National
Marine Electronics Association of America. It is an international standard that
enables equipment from many different manufacturers to be connected
together and to share information.
SeaTalk and NMEA
In
SeaTalk In/Out
2-26
hsb2 Plus Series Fishfinders
Using the SeaTalk
Auxiliary Junction
Box
The information is passed in “sentences”, each of which has a three-letter
sentence identifier. When you check to see if one item will “talk” to another,
make sure that the two items both use the same sentence identifiers. For
example: VTG carries Course and Speed Over Ground data; GLL carries
latitude and longitude; DBT carries water depth; MWV carries relative wind
angle and wind speed data.
The NMEA 0183 standard carries similar information to SeaTalk. However, it
has the important difference that one cable will only carry information in one
direction. For this reason NMEA 0183 is generally used to connect a data
receiver and a transmitter together: for example, a compass sensor
transmitting heading to a radar, or a GPS sensor (or Chartplotter) transmitting
position and navigation data to a radar.
NMEA Input Connection
The two NMEA/Power input connectors are normally used for non-SeaTalk
Compass (heading) data or GPS. It can also be used for additional navigation
data (if not provided via SeaTalk).
Connect the input(s) to the orange and yellow wires (Channel 1) and/or the
green and blue wires (Channel 2). Refer to Power and NMEA Input
Connection on page 2-17 for further details.
For example, to connect a Raymarine Heading Sensor to the NMEA Channel
1 input, connect the cables and power supply using a suitable connector block,
as shown in the diagram below. If installed, it may be convenient to connect
the power to the SeaTalk auxiliary junction box described in the following
section.
Red
Yellow
Black
+12 V
+ NMEA Data (orange)
-- NMEA Data (yellow)
0V
D3604-1
Figure 2-16: NMEA Input Connection
Using the SeaTalk Auxiliary Junction Box
A junction box is used to connect the SeaTalk system to the hsb2 Plus Series
display unit. This junction box enables the SeaTalk bus, power and GPS to be
connected.
2-27
If power is not already available (via another SeaTalk instrument), the
junction box can be used to apply power to the SeaTalk bus for other
applications. The junction box may also be used for other purposes, e.g.,
supplying power to a flux gate compass and routing the compass data to the
hsb2 Plus Series display NMEA In connection, or alternatively, for connecting
a NMEA GPS system.
The junction box includes:
• SeaTalk cable and connector to attach to display unit
• Power cable to connect to 12 V power (if required)
• Input connections to connect SeaTalk cable from external equipment
• Spare connections for another instrument
CAUTION:
Ensure correct polarity of the 12 V supply before applying SeaTalk
power. Use a multimeter to check the connections.
Figure 2-17 shows how to connect the junction box; Appendix B provides
connection details for specific Raymarine, Apelco and Autohelm GPS and
Beacon Receiver systems.
To Display Unit
SeaTalk Socket
To GPS
Power Out: 1 & 2
Power In: 1 & 3
12V
Power
Supply
Spare
Input
Fused
Cable
SeaTalk
Power
GPS
Core
Black (screen)
Red
Yellow
Black (screen)
Red
Black (screen)
Red
Yellow
Terminal
1
2
3
1
2
1
2
3
Function
0V
+12v
SeaTalk
0V
+12V
0V
+12V
SeaTalk
D4291-1
Figure 2-17: Using the Auxiliary Junction Box
Using the SeaTalk
Auxiliary Junction
Box
Chapter 2: Installation
2-28
hsb2 Plus Series Fishfinders
Data Output
Data is transmitted in SeaTalk and NMEA formats as detailed in Appendix D
and can be used to enhance other equipment as required.
Data Output
The SeaTalk input/output connection is detailed in SeaTalk Connection on
page 2-24.
The NMEA output connector is a 4-pin connector as illustrated below. The
1.5 m NMEA OUT cable has a ferrite clamp attached to ensure EMC
conformance.
NMEA OUT connector
NMEA OUT connector
Pin Pin name
Function
Pin 2, white
Pin 5, screen
Rear of display
Pin 3, blue
Pin 4, not connected
3
2
4
5
2
NMEA_GND
NMEA ground
3
NMEA_SIG
NMEA data output
4
N/C
N/C
5
CGND
Screen
*Pin 1 does not exist on this connector
NMEA out
D4254-2
Figure 2-18: NMEA Output Connector
Data Conversion
The hsb2 Plus Series displays convert some information across the
communications links as follows:
NMEA In to NMEA Out and SeaTalk
SeaTalk to NMEA Out
This enables data received by the display to be passed to other instruments. For
example, if you have a master and a repeater display, you only need to connect
NMEA In to the master display, which will pass the data to the repeater via
SeaTalk.
You can prevent NMEA heading data being bridged onto the SeaTalk bus refer to Bridge NMEA Heading on page 7-9.
Note: To transfer NMEA data, or to convert the data, the display must be powered On.
Chapter 2: Installation
2-29
2.8 Integrated System Checks
When you have connected your display unit to the required equipment ensure
that position data is available at the display via NMEA or SeaTalk.
To confirm your chartplotter is operating correctly, perform the following
checks:
1. Without a chart card installed, select the Chart display mode and select a
suitable range scale. Verify that the world map is visible.
Use the trackpad to check cursor movement and normal scrolling action.
2. To ensure that the display is responding to position data:
Press FIND SHIP, check the cursor is fixed on the vessel symbol which is correctly positioned at the center of the chart display.
3. Insert a chart cartridge for the area of your vessel.
Use the RANGE key to zoom-in to check that the chart data is being displayed.
Received Data
If either SeaTalk or NMEA In is connected, verify that the expected data is
displayed.
1. Press DISPLAY and select the NAV DATA WINDOW ON.
Check that the expected data is displayed.
2. If heading data is connected, select Chart mode and check it is displayed in
the heading data box, or select Radar mode and check heading is displayed
in the Status Bar.
Transmitted Data
If SeaTalk or NMEA Out is being transmitted to other equipment, check that
the data is being received correctly.
An NMEA Out connector is used to transmit navigation data. The NMEA
Output cable should be connected to the upper, left connector on the rear of the
display unit.
Note: The NMEA Output cable has a ferrite clamp attached to ensure EMC
conformance.
Integrated System
Checks
Chart Display
2-30
hsb2 Plus Series Fishfinders
Transmitted Data
Chapter 3: Getting Started & Adjusting the Display
3-1
Chapter 3: Getting Started & Adjusting the
Display
This chapter provides information, instructions to get you started using the
hsb2 Plus Series Fishfinder displays. It will help you to become familiar with
the display and the functions of the controls before you start using the unit.
More detailed information on operating the Fishfinder display is provided in
Chapter 4. Chartplotter operating details are given in Chapter 5 and
Chapter 6.
Conventions Used
Throughout this handbook, the dedicated (labelled) keys are shown in bold
capitals; for example, MENU. The soft key functions, menu names and
options are shown in normal capitals; for example, SCREEN.
Operating procedures, which may consist of a single key-press or a sequence
of numbered steps, are indicated by a ➤ symbol in the margin.
When the procedure requires you to press a soft key, the soft key icon is shown
in the margin.
Simulator
The display unit includes a simulator function, that allows you to practice
operating your Fishfinder or Chartplotter (Raychart models only) without data
from the transducer or GPS system. You will need to use the set up options to
switch the display to simulator mode, as described in Section 3.2.
You need to connect the display to a 12V or 24V DC power supply, connecting
the red wire from the power lead to positive (+) and the black wire to negative
(-). See Chapter 2 for full details.
The following section, Section 3.2, includes instructions to view simulated
fishfinder and chart images.
Introduction
3.1 Introduction
3-2
hsb2 Plus Series Fishfinders
3.2 Switching the Display On and Off
The factory default power-up mode is full-screen fishfinder. Once you have
used the display unit it powers-up in the last used mode. The following
sections describe the power-up sequence in fishfinder and chart modes, how to
adjust the lighting and color controls, and how to select simulator mode.
Switching the
Display On and Off
➤
To switch the display on in fishfinder mode:
Press and hold the POWER key until the unit beeps. The keys light up and after
a few moments the display shows the fishfinder screen.
50kHz
AUTO GCRZFH
SD
0
8
38
45
52
100
ft
FREQUENCY
ZOOM
BTM.LOCK
Figure 3-1:
A-SCOPE
Switching On in Fishfinder Mode
You can adjust the display brightness and contrast/colors, as described later in
this chapter.
Setting the Fishfinder as Master/Repeater
You need to set your display as a fishfinder master or repeater. If the display is
connected to a sonar transducer it is a master display. If your display is part of
an integrated system, connected to another fishfinder master it is a repeater
display. Fishfinder functionality is the same on both master and repeater
displays, with the following limitations:
• Automatic Gain cannot be adjusted on the repeater display, but Manual
Gain can be.
• STC cannot be adjusted on the repeater display.
• Depth offset, speed and temperature calibration (see Section 7.4) cannot be
set on the repeater display.
• Frequency can be selected on either master or repeater display, but the
same frequency is used on both displays.
Chapter 3: Getting Started & Adjusting the Display
3-3
• Range adjustment can be made on either master or repeater display, but any
changes made are used on both displays.
• Simulator mode is repeated from the master, but cannot be selected on the
repeater display.
50kHz
0
8
25
38
45
50
52
75
100
ft
FREQUENCY
ZOOM
BTM.LOCK
A-SCOPE
D5008-2
Figure 3-2:
➤
Typical Fishfinder Display at Switch On
To set the fishfinder display as a master or repeater:
1. Press the MENU key, then press the SONAR SET UP soft key. The sonar set
up pop-up window is displayed.
2. Use the trackpad to move the selection bar over the option SONAR HSB
MODE. The HSB mode soft keys are displayed.
3. Press the appropriate soft key to set the display as a MASTER or REPEATER.
Press ENTER twice to return to the default display.
Switching the
Display On and Off
AUTO G RZ
3-4
hsb2 Plus Series Fishfinders
Chart Mode (Raychart Models only)
If the display was last used in chart mode before being powered off, it will
return to chart mode the next time it is switched on.
➤
Switching the
Display On and Off
To switch the display on in chartplotter mode, press and hold the POWER key
until the unit beeps. The keys light up, the Raychart graphic is displayed,
followed by the caution:
CAUTION:
Raychart chart displays are based on cartographic data that C-MAP
believes to be accurate. However, you should not rely on these displays as
your primary source of navigation. Rather, your Raychart should be used
only as a backup to official government charts and traditional methods of
navigation.
When you have read and understood the caution, press the CONTINUE soft key.
The chart is displayed.
If this is the first time the chartplotter has been turned on, and no chart card is
installed, the display shows the small-scale world map and the default soft
keys. Otherwise, the display shows the selected chart area and any data that
were displayed when the display was last used.
Until unit beeps
Figure 3-3:
D4277-3
Switch On - Chart Mode
Switch Off
CAUTION:
To provide protection against the damaging effects of UV light, it is
advisable to replace the sun cover provided when the color LCD display is
not in use.
A reminder is displayed when you switch off the color LCD display.
Chapter 3: Getting Started & Adjusting the Display
➤
3-5
To switch the display unit off, press and hold the POWER key for three
seconds. A countdown timer is displayed as shown below:
GAIN
DISPLAY
VRM/EBL
MARKS
Simulator Mode
MULTI
POWER OFF IN
3s
Countdown timer:
number of seconds
to power off
RANGE
ALARMS
POWER
ENTER
CLEAR
MENU
3
SECONDS
Figure 3-4:
D3599-2
Switch Off
When the counter reaches zero a beep sounds, and the display unit switches
off. Release the POWER key.
Note: Switch the display unit off before you remove either the power or transducer cords.
Simulator Mode
When simulator mode is on a simulator database box is displayed.
When the display is switched off then on again, simulator mode is maintained.
It is recommended that you select the System Set Up Menu and switch off
simulator mode when you have finished.
➤
MENU
SYSTEM
SET UP¬
SONAR
SET UP¬
To view simulated image:
1. Press MENU followed by either:
the SYSTEM SET UP soft key for simulated data or
the SONAR SET UP soft key for a simulated fishfinder image.
The set up menu pop-up is displayed.
2. Use the trackpad to move the selection bar over the option SIMULATOR/
SONAR SIMULATOR. The simulator soft keys are displayed.
3. In the system set up menu, press DATA to view the chart display with simulated position.
In the sonar set up menu, press the ON soft key to switch on the sonar simulator.
4. Press ENTER twice to return to the default display.
Note: Any waypoints placed on the chartplotter in simulator mode are retained in the database list and are available for use in routes.
3-6
hsb2 Plus Series Fishfinders
Changing the Lighting & Contrast (Monochrome LCD)
On the L755RC Plus, you can change the level of backlighting and contrast for
the screen and keys. The key lighting is set the same as the screen lighting,
except that it remains switched on at its lowest level even when the screen
lighting is turned off, so that you can always find the keys.
Changing the
Lighting & Contrast
(Monochrome LCD)
➤
To change the lighting and contrast:
1. Press the MULTI key to display the soft key controls:
The last-used soft key is highlighted in inverse video (white text on a black
background).
POWER
AUTO LO HI
70%
37%
LIGHT
CONTRAST
WHT LINE
OFF ON
D4895-2
2. Press the LIGHT soft key if it is not already highlighted.
3. The LIGHT soft key toggles lighting ON/OFF.
4. Use the trackpad (up or down) to increase or decrease the setting. You can
press and hold the trackpad to change the setting more rapidly. The lighting
level is adjusted as you change the setting.
5. Press the CONTRAST soft key. Adjust the setting in the same way as for the
lighting. There are 64 different contrast levels.
50%
CONTRAST
6. Press ENTER to return to the default screen, with the new lighting and contrast levels retained, or press CLEAR to discard the changes and return to
the default screen.
If lights are left ON when you switch off the display, the next time the display
is switched on, the lights will be ON, but at the default setting of 42%. The new
contrast level is retained until you reset it, unless you set the control very low
or very high; in this case, the contrast will be restored as follows:
Contrast set
Contrast set
< 30%
> 70%
restored to 30%
restored to 70%
Changing the Brightness & Color Settings (Color LCD)
The MULTI key on the color LCD Fishfinder provides controls to set up the
display colors and brightness. You can choose the background color and the
color threshold; color threshold lets you determine which echoes are
displayed, by selecting the minimum color strength the fishfinder uses. You
can also select the color set, for a bold or soft color palette. The brightness of
the screen can be adjusted over a wide range, suitable for viewing in daylight
(high brightness level) or at night (low brightness level).
Chapter 3: Getting Started & Adjusting the Display
3-7
The key lighting is automatically adjusted as you alter the screen lighting, so
that you can always find the keys. If you set the backlight to a high level, the
key lighting is dimmed; if you set the backlight to a low level, the key lighting
level is increased.
➤
To change the screen brightness:
1. Press the MULTI key to display the soft key controls:
70%
POWER
AUTO LO HI
LIGHT
COLOR
SETTINGS
WHT LINE
OFF ON
D4896-2
2. The LIGHT soft key indicates the brightness level, use the trackpad (up or
down) to increase or decrease the setting. You can press and hold the trackpad to change the setting more rapidly. The brightness level is adjusted as
you change the setting.
3. Press ENTER to return to the default screen, with the new brightness level.
➤
MULTI
To set the screen brightness to 100%:
Press and hold the MULTI key for one second. The brightness is increased to
100%.
The brightness level is retained when you switch off the display.
Note: During night-time use, the brightness may be set very low, when subsequently operated during the day it may not be apparent that the display is on;
press MULTI then use the trackpad to increase brightness. Alternatively, press
and hold MULTI for one second to set the brightness to 100%.
Selecting the Background Color
Five colors are available for the fishfinder display background – black, dark
gray, light gray, white and dark blue. The color you select is used on all the
fishfinder windows (scrolling bottom, Zoom, Bottom Lock and A-Scope).
You will probably find that you need to change the background color in
different light conditions. For example, a white background is probably
easiest to see in bright sunlight, but a black background may be preferable at
night.
Changing the
Brightness & Color
Settings (Color LCD)
Adjusting the Brightness
3-8
hsb2 Plus Series Fishfinders
➤
MULTI
To change the background color:
1. Press the MULTI key to display the soft key controls, then press COLOR SETTINGS.
COLOR
SETTINGS
2. Press the BGROUND COLOR soft key. The background color soft keys are
displayed below a pallet of available colors. The selected color is highlighted.
B'GROUND
COLOR
Changing the
Brightness & Color
Settings (Color LCD)
3. Press the left or right BACKGROUND COLOR soft key until the required color
is highlighted.
The fishfinder display changes, so you can see the effect as you change the
background color.
4. Press ENTER or CLEAR twice to return to the MULTI soft keys.
Selecting the Color Threshold
You use the color threshold control to determine the minimum echo strength
that is displayed. Each range of echo strengths is displayed in a color as shown
in the color bar; you select the minimum strength that is displayed by blanking
echo colors below the required minimum.
If you blank a color, the corresponding echoes are displayed in the background
color. You can remove up to six colors, but you cannot remove the strongest
color.
The color threshold you select is used on all the fishfinder windows (scrolling
bottom, Zoom, Bottom Lock and A-Scope).
➤
MULTI
COLOR
SETTINGS
COLOR
THRESH
To change the color threshold:
1. Press the MULTI key to display the soft key controls, then press COLOR SETTINGS.
2. Press the COLOR THRESH soft key. The color threshold soft keys are displayed below color indicator showing the available echo colors.
The weakest color is at the bottom of the indicator, the strongest color at the
top; you can remove colors from the bottom up.
3. Press the left or right ADJUST COLOR THRESHOLD soft key to change the
color threshold.
Pressing the left key removes out the next color up, it increases the minimum strength displayed.
Pressing the right key displays the next color down, it decreases the minimum strength displayed.
4. Press ENTER or CLEAR twice to return to the MULTI soft keys.
Chapter 3: Getting Started & Adjusting the Display
3-9
Selecting the Color Set
COLOR
SETTINGS
To change the color palette:
1. Press the MULTI key to display the soft key controls, then press COLOR SETTINGS.
2. Press the COLOR SET soft key; this toggles between color set 1, bolder colors and color set 2, softer colors.
3. Press ENTER or CLEAR twice to return to the default screen.
3.3 Controlling the Display
You control the display using the cursor and control keys. You start all
operations from the default screen, that is the default soft keys are displayed:
Fishfinder
FREQUENCY
ZOOM
BTM.LOCK
A-SCOPE
D5010-1
Chart
ROUTE
GOTO
SCREEN
FIND SHIP
D4160-1
When you have completed an action using the soft keys, press ENTER or
CLEAR to return to the default screen; you may need to press ENTER or
CLEAR several times to back-track through the soft key hierarchy.
Note: If you have set up your system so that the default soft keys are not displayed all the time, press any soft key to display the labels.
The remainder of this section describes how to select the mode of operation
and switch half-screen windows on/off. The following sections describe how
to set up the display for the Fishfinder and for the Chart (for fishfinder displays
with chartplotter functionality).
The controls are summarized in the laminated Quick Reference cards
that accompany this handbook.
Selecting the Mode of Operation
You use the DISPLAY key to select the full-screen mode. If the data is available
on your system, the following modes (described in Operating Modes on
page 1-6) can be selected:
• Chart
Controlling the
Display
➤
MULTI
3-10
hsb2 Plus Series Fishfinders
• Fishfinder (Sonar)
• Data Log
The DISPLAY key also accesses the soft keys for the half-screen window
options.
➤
Selecting the Mode
of Operation
DISPLAY
To change the mode, press the DISPLAY key to show the DISPLAY pop-up, then
press again to cycle through the modes available, shown in Figure 3-5.
"DISPLAY" TO SELECT FULL SCREEN OPTION
SOFTKEYS TO SELECT WINDOW OPTION
CURSOR
BRG 099oR
RNG 2.410nm
CHART SONAR
LOG
40
ft
WINDOWS
OFF ON
SELECT
WINDOWS
SPLIT
HOR VER
D5012-1
Figure 3-5:
Using the DISPLAY Key
The selected mode is shown by an icon with a black (monochrome LCD) or
red (color LCD) border and the mode is displayed on the screen. The
associated half-screen window soft keys are also displayed.
When the required mode is shown, press ENTER or CLEAR. The default soft
keys are displayed. The selected mode is shown full-screen; in Fishfinder and
Chart mode you can switch on half-screen windows for additional display, as
described in the following section.
If you press DISPLAY again, the pop-up and soft keys for the current mode are
shown.
Using the Dedicated Keys in Different Display Modes
When certain dedicated (hard) keys are pressed on a unit with the Raychart
feature, the sets of soft keys that appear can vary depending on whether the
currently selected mode is fishfinder or chart. The following describes the soft
keys that appear in the Fishfinder and Chart modes.
Chapter 3: Getting Started & Adjusting the Display
3-11
POWER
AUTO LO HI
70%
37%
LIGHT
CONTRAST
WHT LINE
OFF ON
D4895-2
In Fishfinder mode on all color displays:
70%
POWER
AUTO LO HI
LIGHT
COLOR
SETTINGS
WHT LINE
OFF ON
D4896-2
In Chartplotter mode on all displays:
70%
LIGHT
ALARMS key
In Fishfinder mode on all displays:
ALARMS
FISH
ALARM
OFF ON
SHALLOW
ALARM
DEEP
ALARM
D5031-1
In Chartplotter mode on all displays:
ALARMS SET UP
ALARMS
ARRIVAL ALARM
0.01nm
OFF TRACK ALARM
ON
ANCHOR ALARM
OFF
GROUNDING ALARM
5M/1.0nm
COUNTDOWN TIMER
00:33:00
ALARM CLOCK
OFF
SELECT ARRIVAL
ALARM RADIUS
D4265-4
Selecting the Mode
of Operation
MULTI key
In Fishfinder mode on the L755RC Plus Monochrome display:
3-12
hsb2 Plus Series Fishfinders
Selecting a Half-Screen Window for Display
Note: Windows can only be used with Fishfinder or Chart screens, they are
not available on the data log screen.
➤
To select a window for display:
Selecting the Mode
of Operation
1. From the full-screen Fishfinder or Chart mode, press the DISPLAY key.
The following soft keys are displayed with an image of each available window:
Fishfinder
WINDOWS
OFF ON
DISPLAY
SELECT
WINDOWS
SPLIT
HOR VER
D5011-1
Chart
DISPLAY
WINDOWS
OFF ON
SELECT
WINDOW
D4156-2
2. In fishfinder mode check that SPLIT is set to HOR. To select a different window, press either SELECT WINDOWS soft key until the required window is
highlighted. If necessary, this will toggle windows on. Press ENTER.
3. To toggle windows off, press the WINDOWS OFF ON soft key.
If any data boxes were displayed at the bottom of the full-screen image, they
are switched off until you return to full-screen mode. However, you can use
the SCREEN soft key in chart mode to switch the data boxes on - they are
displayed in the upper window.
Figure 3-6 shows the half-screen horizontal windows (in fishfinder mode).
Switching Control Between Fishfinder & Chart Screens
In a combined or an integrated system, to switch control between fishfinder,
radar and chart, you can change the full-screen mode using the DISPLAY key.
Alternatively, when you have both fishfinder and chart displayed in halfscreen windows the soft key CHRT SNR lets you toggle operating control
between the fishfinder and the chart window.
If a window is active, i.e., control of the cursor via the trackpad is available in
that window, and you switch windows off, control automatically returns to the
full-screen (upper window) mode.
Chapter 3: Getting Started & Adjusting the Display
3-13
Fishfinder:
FREQUENCY
ZOOM
MORE¬
CHRT SNR
D5013-1
ROUTE
GOTO
MORE¬
CHRT SNR
D5025-1
➤
To change the active window, press the CHRT SNR soft key to toggle control
between the fishfinder and chart display. The current active display is
highlighted in gray (monochrome LCD) or red (color LCD) on the CHRT SNR
label and the cursor appears in that window.
Returning to the Full-Screen Display
To return to the full-screen display you can turn windows off, as previously
described. Alternatively, to return to full-screen display:
➤
DISPLAY
Press and hold the DISPLAY key for 2 seconds to return to the currently
selected full-screen (upper window) display.
Selecting the Mode
of Operation
Chart:
3-14
hsb2 Plus Series Fishfinders
BDI Window
CDI Window
AUTO G RZ
50kHz
AUTO G RZ
50kHz
0
0
Selecting the Mode
of Operation
100
100
150
150
200
ft
200
ft
XTE
225°T
XTE
0.28nm
1.45nm
WPT BRG
WPT BRG
40
351°T
351°T
30
WPT RNG
WPT RNG
26.8nm
ZOOM
WINDOWS
OFF ON
03h:59m
BTM.LOCK
SELECT
WINDOWS
nm
10
STEER STARBOARD
WAYPOINT 001
A-SCOPE
FREQUENCY
SPLIT
HOR VER
WINDOWS
OFF ON
Depth/Temperature Window
AUTO G RZ
20
10
TTG
STEER PORT
WAYPOINT 001
FREQUENCY
20
nm
ZOOM
BTM.LOCK
SELECT
WINDOWS
23.1nm
TTG
01h:13m
A-SCOPE
SPLIT
HOR VER
Chart Window
50kHz
AUTO G RZ
50kHz
0
0
100
100
150
150
200
ft
TEMPERATURE (°C)
200
ft
DEPTH (ft)
12.8
26.4
26.0
50
25.6
25.2
91
24.8
131
24.4
24.0
170
23.6
200
23.2
60
50
FREQUENCY
WINDOWS
OFF ON
40
30
MINUTES
ZOOM
20
BTM.LOCK
SELECT
WINDOWS
10
0
A-SCOPE
FREQUENCY
SPLIT
HOR VER
WINDOWS
OFF ON
ZOOM
MORE¬
SELECT
WINDOWS
CHRT SNR
SPLIT
HOR VER
D5023-2
Figure 3-6:
Fishfinder Half-Screen Window Options
Chapter 3: Getting Started & Adjusting the Display
3-15
3.4 Fishfinder Display Control Functions
• Viewing databoxes
• Changing the scroll speed
• Changing the range
• Selecting the power setting
• Selecting the frequency
In addition this section describes how to select the fishfinder display options.
• Display Bottom Lock
• Display A-Scope
• Zoom an area of the image.
Viewing Data Boxes
The cursor data box and a group of up to six data boxes can be displayed, if the
information is available on your system. You select which data is displayed
in the boxes during system set up as described in Chapter 7. The default
data box positions are along the bottom of the display. Each box can be moved
to the required position on the screen using the context-sensitive cursor.
To switch the data boxes on and off you need to go to Chart mode – see
Customizing the Screen Presentation Options on page 3-26. Switching the
databoxes on/off in Chart mode also affects their display in Fishfinder Mode.
Changing the Scroll Speed
The standard fishfinder display is the scrolling bottom image; this is a
graphical representation of the echoes seen by the Fishfinder. New
information appears at the right hand side of the display and scrolls to the left.
The speed at which the display scrolls is adjustable, but the same section of the
bottom is displayed regardless of scrolling speed. As illustrated in Figure 3-7,
if you select a faster speed, more detail is displayed and is useful when you are
looking for fish; if you select a slower speed the information remains on the
display for longer.
Fishfinder Display
Control Functions
The Fishfinder automatically locates the bottom and displays the information
using an appropriate scroll speed and range. However, controls are provided
so you can adjust scroll speed and range. You can also select the transducer
frequency and select certain data for display. This section describes how to use
the controls to set-up your fishfinder display:
3-16
hsb2 Plus Series Fishfinders
Changing the Scroll
Speed
Figure 3-7:
Effect of the Scroll Speed
The Fishfinder automatically adjusts the scroll speed, based on depth.
Alternatively you can manually adjust the speed. If you select automatic
adjustment, the scroll speed is related to boat speed as follows:
• Less than, or equal to 0.5 kn, scroll speed is constant at 10%
• Between 0.5–15 kn, scroll speed varies linearly with boat speed
• Greater than 15 kn, scroll speed is constant at 100%
If you select manual adjustment, the scroll speed is not related to the speed of
the boat over the bottom. You can also pause the display (the depth indication
continues to be updated).
➤
To change the scrolling speed:
1. Press MENU, then press the SCROLL SPEED soft key.
MENU
2. If necessary, press the SCROLL AUTO MAN soft key to toggle the setting
between AUTO and MAN.
SCROLL
SPEED
3. For manual adjustment, use the trackpad to increase the scroll speed. You
can press and hold the trackpad to change the value more rapidly.
4. Press ENTER to return to the Menu soft keys, then ENTER again to return to
the default display.
➤
MENU
PAUSE
To pause the scrolling display:
1. Press MENU, then press the SCROLL SPEED soft key.
2. Press the PAUSE soft key. The display stops scrolling and the key is relabeled RESUME.
Chapter 3: Getting Started & Adjusting the Display
3-17
3. To resume scrolling, press the RESUME soft key. The key is relabeled
PAUSE.
4. Press ENTER to return to the Menu soft keys, then ENTER again to return to
the default display.
The POWER soft key provides adjustment of the transducer signal. When AUTO
is selected (default), the Fishfinder automatically determines the power
setting based on the current depth. LO power (100 W) is used in depth ranges
less than 8 ft (2.4 m) and HI power (600 or 1000 W, depending on your
transducer) is selected for depths greater than 12 ft (3.7 m). When AUTO is
selected the current automatic power setting is indicated in the top status line
by an L (low) or H (high).
Note: When AUTO POWER has been selected, and you manually adjust the
RANGE to 30 ft (10 m) or greater, the Fishfinder switches to HI power, regardless of what the digital depth is calculated to be.
If, however, you wish to manually adjust the power to suit current conditions,
you can select either LO or HI power.
The power setting is retained when the unit is powered off.
➤
MULTI
POWER
AUTO LO HI
To change the power setting:
1. Press the MULTI key to display the soft key controls.
2. Press the POWER soft key to toggle between AUTO, LO, or HI power. The
selected setting is highlighted.
3. Press ENTER or CLEAR to return to the default screen.
Changing the Fishfinder Range
The Fishfinder automatically adjusts the display range. Alternatively, the
RANGE key lets you select the maximum depth displayed on the scrolling
bottom and A-Scope displays. You can also set the shift value to move the
image window up or down within the current range.
If you select automatic range adjustment, the Fishfinder selects the shallowest
range that keeps the bottom in the lower half of the display window. Shift is
disabled (the value is ignored) when auto-range is selected.
Selecting the Power
Setting
Selecting the Power Setting
3-18
hsb2 Plus Series Fishfinders
The following range/shift values are available:
Table 3-1:
Range and Shift Values
Feet
Fathoms
Meters
Changing the
Fishfinder Range
Range
Shift
Range
Shift
Range
Shift
5
1
1
1
2
1
10
2
2
1
4
1
15
5
3
1
6
2
20
5
4
1
8
2
30
10
5
1
10
2
40
10
8
2
15
5
50
10
10
2
20
5
60
20
15
5
25
5
80
20
20
5
30
10
100
25
25
5
40
10
150
50
30
10
50
10
200
50
40
10
60
20
250
50
50
10
80
20
300
100
60
20
100
25
400
100
80
20
150
50
600
200
100
25
200
50
800
200
150
50
300
100
1000
250
200
50
400
100
1500
500
250
50
500
100
2000
500
300
100
600
200
2500
500
400
100
800
200
3000
1000
500
100
1000
250
3500
875
600
150
1200
300
4000
1000
700
175
1400
350
4500
1500
750
250
1500
500
5000
1250
850
170
1700
425
Note:
1. Range detection below 3000 ft (1000 m) is only available with the L1250
Plus and L1250RC Plus displays after you have fixed the Depth Range setting to 5000 ft. See Depth Range (L1250 Plus and L1250RC Plus only) on
page 7-15 for details.
2. All other hsb2 Plus Series Fishfinders are limited to a maximum depth
range of 3000 ft (1000 m), unless repeating data from an L1250 Plus or
L1250RC Plus via the High Speed Bus.
Chapter 3: Getting Started & Adjusting the Display
➤
RANGE
3-19
To adjust the range and shift values:
1. Press RANGE, this sets adjustment to manual and the range soft keys are
displayed. The range adjusts up or down depending on the direction
pressed.
RANGE
AUTO MAN
3. If necessary, press the RANGE AUTO MAN soft key to select AUTO range.
AUTO range is indicated by the letter R in the status bar.
4. To adjust the shift, press the appropriate SHIFT soft key: use the up soft key
to select a shallower shift, use the down soft key to select a deeper shift.
The image window is shifted up by the selected amount
5. Press ENTER to return to the default display.
When AUTO POWER has been selected, and you manually adjust the RANGE to
30 ft (10 m) or greater, the Fishfinder switches to HI power, regardless of what
the digital depth is calculated to be.
Manually Adjusting RANGE to Ignore Surface Clutter
There may be a time when clutter near the water’s surface is so thick it returns
an echo that is stronger than the return from the bottom. In this a case, it is
possible the fishfinder may determine the clutter to be the seabed rather than
the bottom itself. You can use the RANGE setting to force the fishfinder to
ignore any interference in the upper boundaries of the water that may be giving
false bottom readings.
If you manually adjust the RANGE to 400 ft (150 m) or greater, the Fishfinder
ignores the first 25% of the range for the purpose of determining the digital
depth. If the RANGE is set to 400 ft (150 m), the first 100 ft (37.5 m) is ignored
for determining the depth. If the RANGE is set to 3000 ft (1000 m), the first 750
ft (250 m) is ignored, etc.
As an example, let’s say the RANGE is set to 400 ft but there is some clutter at
126 ft that is returning a stronger signal than the bottom. Because its return is
stronger, the fishfinder determines the clutter to be bottom and displays it as
the bottom depth (126 ft). See Figure 3-8.
The upper 25% (400 x 0.25 = 100 ft) of the range is ignored but because the
clutter is deeper than this (126 > 100 ft), the clutter is still detected as bottom.
If you then manually adjust the RANGE to 600 ft, the value that is ignored now
increases to 150 ft (600 x 0.25 = 150). The clutter is now within the excluded
range (126 < 150) and so is ignored. The correct bottom of 302 ft is now
displayed.
Changing the
Fishfinder Range
2. Use the RANGE key to adjust the range: press the up arrow to select a shallower range, press the down arrow to select a deeper range.
3-20
hsb2 Plus Series Fishfinders
AUTO G RZ H
50kHz
AUTO G
Z H
50kHz
0
0
100
200
Selecting the
Frequency
200
400
300
400
ft
FREQUENCY
ZOOM
BTM.LOCK
A-SCOPE
600
ft
FREQUENCY
ZOOM
BTM.LOCK
A-SCOPE
D6061-1
Signal from surface clutter is stronger than
from bottom. When RANGE is set to 400 ft,
clutter is below top 25% of range (100 ft),
so is incorrectly determined to be bottom.
Figure 3-8:
Manually adjusting RANGE to 600 ft, clutter
is now within top 25% of the range (150 ft),
so it is ignored and the correct bottom is
detected.
Manually Adjusting RANGE to Ignore Surface Clutter
Selecting the Frequency
The hsb2 Plus Series Fishfinders use dual frequency sonar. The two
frequencies used are 50 kHz and 200 kHz. The Fishfinder automatically
selects the appropriate frequency. Alternatively, you can manually select
either frequency, or both frequencies simultaneously. Each is suitable for a
particular purpose:
50 kHz Frequency
When using this frequency, the transducer scans a wide area. The 50 kHz
signal penetrates water well, so is good for use in deep water.
200 kHz Frequency
When using this frequency, the transducer scans a narrower area, but produces
a more detailed view. The 200 kHz signal is good for finding fish near the
bottom or close together. It is better for use in shallow water.
Split Frequency
The transducer can operate in both 50 kHz and 200 kHz frequencies at the
same time. If you choose split frequency operation, the scrolling bottom
display is split horizontally; the upper half shows the 200 kHz detailed view
and the lower half shows the 50 kHz image.
Chapter 3: Getting Started & Adjusting the Display
FREQUENCY
To change the frequency:
1. Press the FREQUENCY soft key. The frequency selection soft keys are displayed.
2. Press the appropriate soft key – 50 KHZ, 200 KHZ or SPLIT. The scrolling bottom is displayed in the selected frequency. If you choose split, the scrolling
bottom is displayed in both frequencies with 200 kHz in the upper window
and 50 kHz in the lower window.
3. If necessary, press the AUTO FREQ OFF ON soft key to select AUTO frequency. AUTO frequency is indicated by the letter F in the status bar.
4. Press ENTER or CLEAR to return to the default display.
You can choose the split frequency display with the fishfinder display options,
Bottom Lock, A-Scope, or Zoom.
When the RANGE has been manually set to 400 ft (150 m) or greater, the digital
depth calculation will be made at 50kHz, regardless of the FREQUENCY setting
used. 200kHz can still be displayed, but will not be used in determining the
depth.
Using Bottom Lock
The scrolling bottom display provides a top-down view, referenced from the
surface of the water. Bottom Lock shows a water column of fixed height,
referenced from the bottom, that appears flat. It removes bottom detail to
provide an image of objects directly above the bottom, and is useful when you
are looking for fish that feed close to the bottom.
You can select the Bottom Lock image to be vertically split with the scrolling
bottom display, or it can replace the scrolling bottom display.
As illustrated in Figure 3-9, the bottom is shown as a straight line. Notice that
some bottom features may extend above this line. The actual depth reading is
given in the bottom left hand corner of the Bottom Lock display.
Range intervals on Bottom Lock are measured up from the bottom (rather than
down from the surface). Thus, the bottom is shown as zero and the top number
indicates the maximum distance above the bottom being displayed. You can
adjust the Bottom Lock range.
If the A-Scope or Zoom image was displayed, selecting Bottom Lock
automatically switches OFF A-Scope or Zoom.
If you have split frequency selected, the Bottom Lock image is displayed in
both frequency windows.
If Target Depth ID is ON (see Target Depth ID on page 7-13), the target depth
is displayed as distance from the bottom.
Using Bottom Lock
➤
3-21
3-22
hsb2 Plus Series Fishfinders
➤
BTM.LOCK
To display the Bottom Lock image:
1. Press the BTM. LOCK soft key. The Bottom Lock selection soft keys are displayed.
2. Press the BTM. LOCK OFF ON soft key to toggle the function ON.
AUTO G Z
200kHz
Using Bottom Lock
20
15
10
5
0
ft
FREQUENCY
ZOOM
BTM.LOCK
A-SCOPE
D5015-2
Figure 3-9:
Bottom Lock Display
3. Press the BTM. LOCK FULL SPLIT soft key to toggle between a full window
bottom lock image or split windows. The bottom lock image is displayed.
If you select split windows, the fishfinder display is split vertically, with
the bottom lock image in the left hand window and the scrolling bottom
display in the right hand window.
In a split window display, a vertical bar appears (along the right hand edge
of the scrolling bottom image) that references the range being displayed in
the bottom lock window. This bar varies in height as the bottom lock range
is changed.
4. To adjust the range, press the appropriate BTM LOCK RANGE soft key: press
the up arrow to select a larger range, press the down arrow to select a
smaller range.
5. Press ENTER or CLEAR to return to the default display.
Chapter 3: Getting Started & Adjusting the Display
➤
3-23
To reposition the bottom lock image:
1. Use the trackpad to move the cursor to the bottom image until the text BL is
displayed near the cursor.
BL
3. Press ENTER to reposition the bottom lock image, or CLEAR to cancel the
operation.
Using A-Scope
The scrolling bottom display provides a historical record of sonar echoes. Use
the A-Scope screen to show raw sonar data directly from the transducer beam.
This gives you a “real time” image of fish and bottom structure directly below
the transducer. This function is very useful in showing the strength of the echo
returned from a fish. At the lower end of the window, A-Scope also displays
the patented Bottom Coverage width indication.
➤
To display the A-Scope image:
1. Press the A-SCOPE soft key. The display is split vertically, with the A-Scope
image in the right hand window and the scrolling bottom image in the left
hand window.
A-SCOPE
2. Press the A-SCOPE MODE soft key to select one of the three modes for
A-Scope, as demonstrated in Figure 3-10:
A-SCOPE
MODE
1 2 3
i. Mode 1, in which the A-Scope image is angled outward as the signal
width (indicated with dotted lines) increases with depth.
ii. Mode 2, in which the image expands to take up the entire A-Scope window, providing greater resolution.
iii. Mode 3, in which only the left hand side of the image displayed in Mode
2 expands to the entire A-Scope window. This mode provides the greatest resolution.
3. Press ENTER to accept your selection.
Note: If the Bottom Lock or Zoom image is displayed, selecting A-Scope automatically switches OFF Bottom Lock or Zoom.
If you have split frequency selected, the A-Scope image is displayed in both
frequency windows.
➤
To remove the A-Scope image:
1. Press the A-SCOPE soft key.
A-SCOPE
OFF ON
2. Press the A-SCOPE ON OFF soft key to toggle off A-Scope.
3. Press ENTER.
Using A-Scope
2. Press ENTER, a horizontal line appears, indicating the cursor is active. Use
the trackpad to move the line to the required bottom lock image position.
3-24
hsb2 Plus Series Fishfinders
50kHz
AUTO G Z
0
25
25
35
Using Zoom
50
65
75
ft
FREQUENCY
ZOOM
100
BTM.LOCK
52.3
52.3
52.3
A-SCOPE
A-SCOPE
A-SCOPE
Figure 3-10: The Three Modes of A-Scope
Using Zoom
Zoom enlarges all or part of the scrolling bottom display. You can select
automatic zoom so the fishfinder selects a zoom level that keeps the bottom in
the lower half of the display window. Alternatively, you can manually pick the
area to be zoomed.
➤
ZOOM
To select zoom:
1. Press the ZOOM soft key, if necessary press the ZOOM ON OFF soft key to
toggle zoom on.
2. Press the ZOOM FULL SPLT soft key to toggle between a full window zoom
image or split windows.
If you select split windows, the display is split vertically, with the zoom
image in the left hand window and the scrolling bottom display in the right
hand window.
In a split window display, a vertical bar appears (along the right hand edge
of the scrolling bottom image) that references the range being displayed in
the zoom window. This bar varies in height with the selected zoom level.
3. If necessary, press the ZOOM AUTO MAN soft key to toggle the setting
between AUTO and MAN. The manual setting allows you to reposition the
zoomed image.
4. For zoom level selection, press the ZOOM X 2 4 6 soft key until the required
zoom level is selected.
5. Press ENTER or CLEAR to return to the default display.
Chapter 3: Getting Started & Adjusting the Display
To reposition the zoom window:
If manual zoom is selected, you can reposition the area of the image that is
zoomed.
1. Use the trackpad to place the cursor in the zoom window, the text ZOOM is
displayed near the cursor.
2. Press ENTER, a horizontal line appears, indicating the cursor is active. Use
the trackpad to select the new position.
3. Press ENTER to reposition the zoom image, or CLEAR to cancel the operation.
If the Bottom Lock or A-Scope image was displayed, selecting Zoom
automatically switches OFF Bottom Lock or A-Scope.
If you have split frequency selected, the selected Zoom image is displayed in
both frequency windows.
Using Zoom
➤
3-25
3-26
hsb2 Plus Series Fishfinders
3.5 Chart Display Control Functions (Raychart Models)
Customizing the Screen Presentation Options
The SCREEN soft key lets you set the following screen presentation options on
or off:
Chart Display
Control Functions
(Raychart Models)
CRSR BOX
OFF ON
CHRT GRID DATABOXES
OFF ON
OFF ON
CUSTOM
OFF ON
D4177-1
Switching the Cursor Data Box On and Off
The cursor data box provides the cursor’s position in latitude/longitude and/or
bearing/range. If you wish to see a full image, you can switch the data box off.
➤
To control the cursor data box:
1. Press the SCREEN soft key.
SCREEN
2. Press the CRSR BOX soft key to toggle the setting from OFF to ON or from ON
to OFF.
CRSR BOX
OFF ON
3. To return to the default soft key display, press ENTER.
➤
You can move the cursor data box using the context-sensitive cursor.
Switching Chart Grid On and Off
The Chartplotter display includes grid lines of latitude and longitude, which
you can use to help determine position on the chart. The grid lines can be
switched on if required.
➤
SCREEN
CHRT
CRSR GRID
BOX
OFF ON
To turn the chart grid on or off:
1. Press the SCREEN default soft key.
2. Press the CHRT GRID soft key to toggle the setting from OFF to ON or from
ON to OFF.
To return to the default soft key display, press ENTER.
Data Boxes
A group of up to six data boxes can be displayed, if the information is available
on your system. You select which data is displayed in the boxes during
system set up as described in Chapter 7.
The default data box positions are along the bottom of the display. Each box
can be moved to the required position on the screen using the context-sensitive
cursor.
Note: If you select fishfinder, BDI, CDI or Nav Data for display in a halfscreen window, the data boxes are temporarily hidden.
Chapter 3: Getting Started & Adjusting the Display
3-27
At any time, you can switch the group of data boxes on or off using the SCREEN
soft key. When first installed, the boxes are all OFF. When the display unit is
switched off and on again, the data boxes return to their last-used states (ON or
OFF) and positions.
➤
To switch the group of data boxes on or off:
1. Press the SCREEN default soft key.
SCREEN
2. Press the DATABOXES soft key to toggle the setting from ON to OFF or from
OFF to ON.
CHRT
CRSR GRID
BOX
DATABOXES
OFF ON
To return to the default soft key display, press ENTER.
If you turn the data boxes on and none are displayed, you need to select the
ones you require using the system set up menu, as described in Section 7.3.
➤
To move any data box:
1. Use the trackpad to position the cursor over the box until the letters BOX are
displayed.
BOX
2. Press ENTER to take control of the box, use the trackpad to move it to the
required position, and press ENTER again.
Custom Options - Chart Mode
When chart details have been customized in the Chart Set Up menu (as
described in Section 7.5) the SCREEN soft key can be used to switch the custom
chart options off or on:
When set to ON, all chart options set to CUSTOM in the Customize Chart menu
are displayed; when set to OFF, options set to CUSTOM are not shown.
The factory default for custom chart options is ON.
➤
SCREEN
CHRT
CUSTOM
GRID
CRSR
BOX
DATABOXES
OFF ON
To switch the customized options on or off:
1. Press the SCREEN default soft key.
2. Press the CUSTOM soft key to toggle the setting from OFF to ON or from ON
to OFF.
To return to the default soft key display, press ENTER.
Customizing the
Screen Presentation
Options
Note: The SCREEN soft key does not control the sixteen data boxes that can be
displayed in the half-screen window.
3-28
hsb2 Plus Series Fishfinders
Moving Around the Chart
Moving Around the
Chart
You will normally operate the chartplotter with the chart showing your
vessel’s current location. The default orientation is North-Up, and the vessel
moves across the screen. You will need to move the chart if your vessel moves
out of the area currently displayed, or if you wish to examine or place
waypoints in another area. Alternatively, you can home the cursor onto the
vessel using FIND SHIP.
There are four ways in which you can move the chart:
• Use the trackpad to move the cursor to the edge of the chart. The chart will
pan across. This method is useful if the area you wish to see is only just off
the screen.
• Use the context-sensitive cursor to change the chart center.
• Automatically re-center the vessel using the FIND SHIP soft key.
• Change the chart scale to zoom out and in to a new area centered on the cursor position. This method is useful if the area you wish to see is a long distance away.
Changing the Chart Center
You can move the area of the chart displayed on the screen using the contextsensitive cursor. This allows you to center your vessel in the middle of the
screen, or to move the chart so that your vessel is displayed off-center
anywhere on the screen.
➤
To center the chart:
1. Use the trackpad to move the cursor to the vessel’s position. The cursor text
POS is displayed.
POS
2. Press CLEAR. The chart is moved so that your vessel’s position is in the
center of the screen.
3. Use FIND SHIP, as described in the following section.
➤
POS
To move your vessel’s position off-center:
1. Move the cursor over your vessel’s position until the letters POS are displayed.
2. Press ENTER to take control of the chart position. The letters POS are now
in inverse video, and the cursor symbol has changed to a four-way arrow.
This indicates that the cursor can be used to move the chart in any direction.
3-29
Moving Around the
Chart
Chapter 3: Getting Started & Adjusting the Display
D4278-1
Figure 3-11: Changing the Chart Center
3. Use the trackpad to move the cursor to the required position.
4. Press ENTER to select the position and return to normal cursor control. The
chart is redrawn with the vessel position at the cursor.
Alternatively, you can press CLEAR to abandon the move and leave the
chart (and vessel) in its former position.
Using FIND SHIP
FIND SHIP is used in chart mode to re-draw the chart with the vessel at the center
and the cursor homed onto the vessel.
ROUTE
GOTO
SCREEN
FIND SHIP
D4160-1
When you press FIND SHIP the following occur:
• The chart is re-drawn with the vessel’s position in the center.
• The cursor is homed onto the vessel position and moves with it.
• When the vessel moves near the edge of the chart window, the chart is
redrawn to place the vessel and cursor at the center again.
• The status bar indicates vessel position, speed and course over ground.
➤
To release the cursor from homed mode press the trackpad to move the cursor
away from the vessel’s current position. The status bar shows the cursor
position, range and bearing.
3-30
hsb2 Plus Series Fishfinders
Changing the Chart Scale
The RANGE key allows you to change the chart scale so that you can see a
smaller or larger area on the screen.
Moving Around the
Chart
Plotter mode is available to allow you to zoom into a smaller area, even when
no chart data is available for that scale. Section 7.5 describes how to set plotter
mode on/off.
The cartographic detail available on charts varies according to the chart scale
and some areas include detail at smaller scales than others. This can cause
blank areas on the display when adjacent areas with different levels of detail
are displayed. To reduce this effect you can use the Chart Set Up options (see
Section 7.5) to set chart display detail to simple. Then, as you zoom in, charted
areas are displayed but with less detail shown.
You can change the chart scale for two purposes:
• To see either more detail (of a smaller area) or a larger area (in less detail)
on the screen.
• To move the display to another area of the chart, by zooming out to a small
scale chart, then zooming in on another position centered on the cursor.
Each time you press the RANGE key, the chart scale changes to the next
available setting. The status bar indicates the distance from top to bottom of
the screen, in nautical miles.
Increases the
chart distance
Vertical distance
displayed on chart
RANGE
Decreases the
chart distance
➤
RANGE
6nm
CSR
POS
50 45'980N
001 01'490W
Status Bar
D4175-3
To change the scale quickly, press and hold the required arrow on the RANGE
key.
The distance indicator at the left-hand end of the status bar is updated
whenever you change the chart scale.
➤
To zoom in to a larger-scale (more detailed) chart:
1. Use the trackpad to position the cursor in the area you wish to see in more
detail.
2. Press the lower part of the RANGE key to zoom into the area.
RANGE
The section of the chart around the cursor is enlarged to fill the screen with
a larger-scale chart showing more detail. The cursor is now positioned in
the center of the screen.
The distance indicated at the top left of the screen is updated.
Chapter 3: Getting Started & Adjusting the Display
3-31
3. If further chart enlargement is available using the current chart card you
can press the bottom of the RANGE key to zoom in again, re-positioning
the cursor first if required.
Moving Around the
Chart
An area of further chart detail is indicated by a box around the area as
shown in Figure 3-12.
Chart Boundary indicates further
detail is available inside
D4279-2
Figure 3-12: Chart Boundaries
4. When no further chart detail is available, as you press the bottom of the
RANGE key, the effect depends on whether Plotter Mode is on or off as
follows:
• If Plotter Mode is Off, the chart scale remains unchanged, indicating
the smallest chart scale is displayed.
• If Plotter Mode is On, the scale is decreased and the message NO CHART
DATA is displayed. The vessel, waypoints, routes and tracklines are displayed without cartography.
The chart information is restored when you return to a chart scale for which the
information is available.
➤
RANGE
To zoom out to a smaller-scale (less detailed) chart, simply press the upper part
of the RANGE key as many times as required.
3-32
hsb2 Plus Series Fishfinders
Radar/Chart Overlay
If radar data is available from another display connected on hsb2, the radar
targets can be overlaid onto the full-screen chartplotter display. The radar/
chart overlay option helps you to distinguish between fixed, charted objects
and other objects that could be moving vessels. Some radar controls are
available in overlay mode.
Moving Around the
Chart
The following criteria must be true for radar/chart overlay to function
correctly:
• Position and heading data are provided so that vessel position and orientation can be determined.
• The vessel must be displayed on screen.
• The chartplotter must be in North Up or Course Up mode (see Section 7.7).
• The chartplotter range must be between 1/4nm and 48nm (equivalent to a
radar range of 1/8nm to 24nm).
• Custom range scales are disabled on the radar.
• The radar must be transmitting.
To ensure the vessel remains on the screen, you could use Find Ship (see Using
FIND SHIP on page 3-29) to home the cursor onto the vessel.
When Radar/Chart overlay is switched on, the status bar indicates OVL. If the
option is switched on but the overlay is not visible (because one of the above
criteria has failed), the status bar indication changes to (OVL).
When Radar/Chart overlay is switched on the soft key MORE... provides
access to the SCREEN soft key and to the radar controls TARGETS and MARPA.
The radar GAIN control is also active in overlay mode.
Note: Radar/Chart overlay is displayed at the current chart range. You
should be aware that if radar is shown on any other display, its range will
match that displayed on Radar/Chart overlay. Conversely, if you change the
radar range on any display, the Radar/Chart overlay image will change to the
new radar range.
➤
To select radar/chart overlay:
1. Press the DISPLAY key to show the DISPLAY pop-up, then if necessary
press again to select Chart mode.
2. Press the OVERLAY OFF ON soft key to toggle the option on.
The two highest intensity radar returns are displayed in purple, over the chart
image. The radar image is translucent, so that chart text, contours and outlines
are visible beneath the radar targets.
Chapter 4: Fishfinder Operations
4-1
Chapter 4: Fishfinder Operations
4.1 Introduction
Basic Fishfinder operation, including a description of the different display
options, was given in Chapter 3. This chapter helps you the get the most from
your Fishfinder. It describes how to fine-tune the image and use the controls to
get additional information.
• Interpreting and Adjusting the Fishfinder Image, including fish and bottom indications, using the white line feature and adjusting gain (sensitivity)
• Viewing Data Windows
• Setting up and Using Alarms for fish, shallow water and deep water
• Using a VRM to Determine Depth and Distance from Boat of a particular
spot
• Placing Waypoints
• Using the Man Overboard (MOB) function
4.2 Interpreting and Adjusting the Fishfinder Image
The hsb2 Plus Series Fishfinders use sound waves (sonar) to find fish and show
the bottom of a lake or sea. The transducer sends high-frequency sound waves
down into the water; these sound waves strike fish, the bottom, or other objects
in the water and return as echoes. The fishfinder interprets these echoes to
present an image of the fish and bottom.
The strength of echoes is indicated by different colors (or shades of gray in the
monochrome L755RC Plus). You can use this information to determine the
size of fish and the bottom structure. Other objects in the water, such as debris
and air bubbles, also return echoes; these echoes are generally weaker than the
fish or bottom echoes and produce background noise or clutter on the
Fishfinder display.
The Fishfinder provides controls to reduce the background noise and to adjust
the way in which echoes of different strengths are displayed. The color
Fishfinders also let you select the background color and remove the display
colors for weaker echoes. Refer to Changing the Brightness & Color Settings
(Color LCD) on page 3-6 for details on these two functions.
Introduction
This chapter covers the following topics:
4-2
hsb2 Plus Series Fishfinders
The Fishfinder provides a White Line feature which helps to distinguish
between the bottom and fish (or other items such as weed) that are close to the
bottom.
Fish Indications
Fish Indications
When the Fishfinder detects a fish, it displays an arch-shaped mark. In
general, a larger arch indicates a larger fish, though this rule is not always true.
Let’s say that there are two fish of the same size: one is close to the surface, the
other is near the bottom. The fish which is close to the surface has a larger arch
because, being closer, more sound waves get returned to the Fishfinder.
To display the depth of the fish, switch on the TARGET DEPTH ID from the
SONAR SET UP menu, as described in Section 7.4, Fishfinder Set Up
Parameters.
The sound waves are actually reflected by the swim bladder near the center of
the fish, not by the body of the fish. The size of this swim bladder is different
for different kinds of fish and this can affect the size of fish arches on the
image. A fish with a large swim bladder produces a large fish arch, while a fish
with a small one produces a small arch. Several arches together show a school
of fish. Figure Figure 4-1 illustrates some typical fish indications.
An arch-shaped image indicates a fish.
The same fish appears differently when shown by the
50 kHz or 200 kHz transducer beams.
50 kHz
200 kHz
A shallow arch is generated when the the boat is
moving slowly.
This indicates a group of small fish.
A fish moving under a stopped boat shows as a line.
When the boat is moving very fast, a fish appears as
two parallel lines.
D5017-2
Figure 4-1:
Fish Indications
Chapter 4: Fishfinder Operations
4-3
Effect of Frequency and Boat Speed
The shape of the arch is also affected by the speed of the boat. If the boat is
moving slowly, the arches tend to be longer; if the boat is moving more
quickly, the arches are short and peaked. If the boat is moving very fast, a fish
may be indicated by a single vertical line.
In Bottom lock mode the fish arches may appear distorted as the bottom
topography is removed from the image.
Bottom Indications
The bottom usually produces a strong echo, so it is easy for the Fishfinder to
see a lot of detail. The Fishfinder can indicate many different kinds of bottom
conditions.
As illustrated in Figure 4-2, a hard bottom appears as a thin line.
A
Hard bottom (sand)
B
Soft bottom (mud)
C
Rocky bottom
D
White line feature on:
D5016-2
Figure 4-2:
Fishfinder Bottom Indications
Bottom Indications
The return from a fish has a different appearance depending on the frequency
used: 50kHz produces a wide beam, so a fish spotted by this frequency gives a
broad arch; the 200 kHz beam is narrower so the same fish produces a
narrower arch.
4-4
hsb2 Plus Series Fishfinders
An uneven bottom which is covered with rocks or coral produces a complex
display; the bottom image is irregular, with long tails pointing upward. A
wreck produces a similar image.
A softer bottom or a bottom covered with seaweed produces a wide line, as the
sound waves reflect from different layers of the bottom. In Figure 4.2b, the
Fishfinder is getting a good echo from the bottom, so the upper layer of the
bottom is shown as dark gray.
Using White Line
Notice that the lower layer of the bottom is shown as a lighter gray, this
indicates a weaker echo. This could mean that the upper layer is soft; some
sound waves may get through this layer and be reflected as a more solid layer
below.
It is also possible that the sound waves are making two complete trips – hitting
the bottom, bouncing off the boat, then reflecting off the bottom again; this can
happen if the water is shallow, the bottom is hard, or gain is set high.
Using White Line
The White Line feature separates echoes from fish near the bottom and the
bottom itself. When the White Line is switched on, the Fishfinder displays the
echoes differently.
With color LCDs, the strongest echoes are displayed in the background color
with a thin line on top. All other echoes remain unchanged.
In the L755RC Plus monochrome LCD, the weakest echoes continue to be
displayed in the background color white, but colors for the other signal are
reversed. Thus, from the strongest to the second weakest the colors are: light
gray with a thin black line on top, dark gray, black.
➤
To switch the white line feature on and off:
MULTI
1. Press the MULTI key, the WHT LINE soft key is displayed.
WHT LINE
OFF ON
2. Press the WHT LINE soft key to toggle the white line feature ON or OFF.
Adjusting Display Gain (Sensitivity)
The fishfinder provides controls for GAIN, COLOR GAIN, and STC. These
controls, accessed from the GAIN key, are used to reduce background noise
and determine how different strength echoes are shown. Automatic
adjustment of GAIN or COLOR GAIN is available, alternatively you can
manually adjust any of these parameters using the trackpad and you can finetune the auto-gain setting. You adjust gain for each transducer frequency
independently.
Chapter 4: Fishfinder Operations
4-5
The color bar on the right hand side of the display, when set to ON in the
Fishfinder Set Up menu (see Section 7.4), shows the colors being used, with
strongest echo color at the top and the weakest echo color at the bottom. The
height of each bar indicates the range of signal strengths displayed in that
color.
AUTO
80%
MULTI
GAIN
GAIN
Gain
The GAIN, or sensitivity, of the display adjusts background noise by varying
echo strength for display. The value of the GAIN control determines the
strength above which echoes are displayed: If the gain is low only the
strongest echoes are displayed; as the gain is increased more, but weaker
echoes (from, say air bubbles) are displayed.
The display GAIN should be set high enough to see fish and bottom detail, but
without too much background noise. Generally, a high gain is used in deep
and/or clear water; a low gain in shallow and/or murky water.
The fishfinder provides automatic or manual GAIN adjustment. Automatic
adjustment is based on depth and water conditions. As conditions change the
auto-gain adjusts to display fish with a minimum of background noise. You
can manually add a bias to the auto-gain setting. If you select manual
adjustment, you will need to re-adjust the gain as conditions change.
Color Gain
MULTI
GAIN
MANUAL
50%
CLR GAIN
The COLOR GAIN determines how echoes of different strengths are displayed.
Three shades of gray (monochrome LCD) or seven colors (color LCD) per
palette are available and the echo strengths are divided into three
(monochrome) or seven (color) bands to correspond with each shade of gray/
color.
The COLOR GAIN control sets the lower limit for the top color band:
All echoes with a signal strength above this value are displayed in the
strongest shade/color.
All echoes weaker than this value are divided equally between the remaining
shades/colors.
Setting a low value produces small band for the strongest color, but a wide
signal band for the other colors; setting a high value gives a wide band for the
strongest color, but a small signal band for the other colors.
Adjusting Display
Gain (Sensitivity)
If you change the settings, the new GAIN, COLOR GAIN, or STC values and mode
(auto or manual) remain set even when you turn off the display. However, any
fine-tuning you make to auto-gain is removed when the unit is powered off.
4-6
hsb2 Plus Series Fishfinders
Note: The color LCD Fishfinder also provides a COLOR THRESHOLD control
to reduce the number of colors displayed. You can use COLOR THRESHOLD
with COLOR GAIN to determine how echoes are displayed.
The Fishfinder provides automatic or manual COLOR GAIN adjustment.
Automatic adjustment displays colors based on current conditions, with as
many colors as possible, while minimizing noise and clutter. As conditions
change the auto-color gain adjusts. You can manually add bias to the autocolor gain settings. If you select manual adjustment, you will need to re-adjust
the gain as conditions change.
Adjusting Display
Gain (Sensitivity)
STC
S TC (Sensitivity Time Control) reduces surface clutter by reducing the gain in
the top 30-40 ft of the display: A low STC value has little effect on gain in
shallow water; a high S TC value decreases the gain in shallow water, thus only
the strongest echoes are displayed.
MULTI
GAIN
25%
This function is useful for reducing background noise, caused by air bubbles
and floating debris, that often appears in shallow water.
STC
➤
MULTI
GAIN
GAIN
ADJUST
200 50
To adjust a parameter:
1. Press the GAIN key, the gain sliders are displayed. The last used slider is
highlighted (displayed in inverse video) to show that it is selected.
2. If necessary on a split frequency display, press the GAIN ADJUST soft key to
select the required frequency for adjustment.
Note: On a single frequency display you adjust the gain for the displayed frequency.
3. If necessary, press the required soft key so the slider is highlighted.
Press it again, if necessary, to toggle between AUTO and MANUAL adjustment.
4. Use the trackpad to move the slider up or down. You can press and hold the
trackpad to move the slider quickly rather than in single steps.
The image on the screen changes as you move the slider and the value is
indicated in the slider.
Note: Because the changes to the settings are made immediately, you cannot
revert to the previous settings by pressing CLEAR.
5. When you have set all the controls to the levels you require, press ENTER
or CLEAR to return to the default display.
Chapter 4: Fishfinder Operations
4-7
4.3 Fishfinder Data Window
The Fishfinder can display various measurements in large format data boxes.
Use the DISPLAY key options to select a data window that is vertically split
with the full-screen fishfinder display. Three data windows are available, each
window provides several large-format data boxes for specific information as
follows:
0
POSITION
WAYPOINT
81°06^34W
28°17^07N
Rng 2.95nm
Brg 093°T
F
20.1
20
COURSE OVER GROUND
40
SPEED OVER GROUND
60
DEPTH
COURSE OVER GROUND
15.1
CURSOR
BRG 099oR
30
MINUTES
0
RNG 2.410
nm
SPEED
10.1
T
kts
DEPTH
M
FREQUENCY
Figure 4-3:
ZOOM
kts
80
ft
BTM.LOCK
T
SPEED OVER GROUND
A-SCOPE
kts
DEPTH
ft
ft
Fishfinder Data Windows
• Data Window A – provides surface temperature with a 30 minute temperature graph, speed through water and depth.
• Data Window B – provides position, course over ground (COG), speed
over ground (SOG) and depth.
• Data Window C – provides waypoint range and bearing, course over
ground (COG), speed over ground (SOG), and depth.
The data boxes display information in the units selected in system set up (see
Section 7.3).
Fishfinder Data
Window
50kHz
AUTO G RZ
4-8
hsb2 Plus Series Fishfinders
4.4 Using Alarms
ALARMS
MULTI
The ALARMS key is used to set up alarms; three alarms are available to alert
you of fish, shallow water and deep water. Each alarm can be toggled ON and
OFF, and you set the depth at which shallow and deep water alarms are
triggered (between the ranges 2–3000 feet/0.5–500 fathoms/1–1000 meters).
You may want to use the shallow and deep water alarms when you are
anchored. Set the limits to just above and below your anchor depth; the
Fishfinder triggers an alarm if the anchor drags and the boats moves into
shallower or deeper water.
Using Alarms
• Fish Alarm – If this alarm is ON the unit sounds a buzzer whenever it finds
a fish. Different buzzer tones are used to indicate fish detected by the
50 kHz and 200 kHz frequencies.
• Shallow water – You set depth at which the shallow water alarm triggers.
When the depth is less than that set, the buzzer sounds and a pop-up window describing the alarm is displayed. You cannot set the shallow alarm to
be deeper than the deep alarm.
• Deep water – You set depth at which the deep water alarm triggers.When
the depth is more than that set, the buzzer sounds and a pop-up window
describing the alarm is displayed. You cannot set the deep alarm to be shallower than the shallow alarm. After you have acknowledged the sounding of a
deep water alarm, a minimum of 30 seconds must elapse before a another depth
alarm can sound again.
The top line status bar shows the condition of the alarms:
•
indicates an alarm is enabled. The speaker symbol is unfilled until an
alarm is triggered and silenced, then the symbol is shown solid.
• S indicates the shallow alarm is enabled; a pop-up window indicates when
the alarm is triggered.
• D indicates the deep alarm is enabled; a pop-up window indicates when the
alarm is triggered.
•
indicates the fish alarm is enabled.
External Alarms
All SeaTalk system alarms (except autopilot, shallow and deep) alarms are
received and displayed on the Fishfinder. You can silence these alarms by
pressing any key. No other action is taken by the Fishfinder except to silence
the alarm.
Chapter 4: Fishfinder Operations
➤
4-9
To set an alarm
1. Press the ALARMS key. The alarms soft keys are displayed.
ALARMS
FISH
ALARM
OFF ON
SHALLOW
ALARM
DEEP
ALARM
2. For the shallow or deep alarms, press the SHALLOW ALARM or DEEP ALARM
soft key then use the up or down soft keys to change the alarm limit.
Press the up arrow (right) soft key to select deeper water; press the down
arrow (left) soft key to select shallower water.
The depth is in the units selected in system set up (see section Section 7.4)
3. If required, press the ALARM OFF ON soft key to toggle the alarm on or off.
If you turn the shallow or deep alarm off, its value is retained and will be
used when you turn the alarm on again.
4. Press ENTER or CLEAR to save the changes and clear the list.
➤
To silence an alarm and clear the alarm message, press any key.
4.5 Using VRM to Determine Depth & Distance from Boat
VRM/EBL
The VRM (variable range marker) key is used on the Fishfinder to determine
the depth and distance-behind-boat of an object on the display. The VRM
function is available on the scrolling fishfinder display, bottom lock and zoom
windows.
A VRM is displayed as a cross hair with height and width of the display
window. The center of the crosshair is the reference for which depth and
distance-behind-boat are displayed. You can use the context-sensitive cursor
to move the VRM over a particular object.
Depth is displayed, in the system units, on the right hand edge of horizontal
line. In the scrolling fishfinder and zoom windows depth is measured from the
surface down. In the bottom lock window, depth is measure from the bottom
up.
Distance-behind-boat is displayed next to the vertical line, at the top of the
window. The VRM distance units correspond to the depth units assigned in the
System Set Up Parameters (see page 7-4) as follows:
System Depth Unit
Meters
Feet
Fathoms
VRM Distance Unit
meters
feet
feet
Using VRM to
Determine Depth &
Distance from Boat
D5031-1
4-10
hsb2 Plus Series Fishfinders
The distance-from-boat continues to update as your boat moves. However, the
vertical line does not scroll with the scrolling fishfinder image. If the display
range changes, the VRM adjusts its relative position so that it does not move
out of the visible display area.
When you switch on the VRM, it is displayed at its last position (unless off
screen, then it is displayed on-screen).
Using VRM to
Determine Depth &
Distance from Boat
If the Fishfinder is in split frequency display mode or a zoom window is
displayed with the scrolling fishfinder image, then the VRM is shown in both
windows at the same position.
If bottom lock is displayed with the scrolling fishfinder image, then the
crosshair lines appear in bottom lock window, but not in the scrolling
fishfinder window.
➤
To switch the VRM on, or re-position an off-screen VRM:
1. Press VRM/EBL.
The VRM is displayed in its last-used position.
The cursor is positioned at the center of the crosshair and has control of the
VRM, as indicated by four-way arrow, the solid crosshair and the text VRM.
VRM/EBL
2. Use the trackpad to position the center of the crosshair over the required
object. The depth and distance-from-boat are updated as you move the cursor.
3. Press ENTER to drop the VRM. The crosshair is displayed as a dashed line.
➤
To move a VRM:
1. Move the cursor over the VRM you wish to change then press ENTER.
The cursor is positioned at the center of the crosshair and has control of the
VRM, as indicated by four-way arrow, the solid crosshair and the text VRM.
VRM
2. Use the trackpad to move the cursor and VRM to the required position.
3. Press ENTER to drop the VRM, or CLEAR to abandon the operation and
return the VRM to its previous position.
➤
To switch the VRM off:
Either:
VRM/EBL
Press VRM/EBL. The VRM is switched off.
Or:
VRM
Move the cursor over the VRM, until the text VRM appears, then press
CLEAR.
Chapter 4: Fishfinder Operations
4-11
4.6 Waypoints
The MARKS key lets you to place up to 998 waypoints. A waypoint is a
position, normally entered on a chart as a reference, or as a place to go to.
However, the hsb2 Plus Series units with Raychart functionality (L755RC
Plus, L760RC Plus, and L1250RC Plus) let you place waypoints in Fishfinder
mode as well as Chartplotter mode.
MARKS
A waypoint can be placed at the cursor position or at the vessel’s current
position (this is sometimes known as an event mark); all waypoints placed on
the Fishfinder are stored in a waypoint database list with position, depth and
temperature when it was placed.
Waypoints placed on the Fishfinder are displayed as a solid vertical line on the
scrolling bottom, Zoom and Bottom Lock displays. The waypoint number is
shown at the top of the vertical line. The waypoint scrolls to the left with the
scrolling bottom display.
If you place a waypoint at the cursor position in Fishfinder mode, and a chart
window is open, the waypoint is displayed on the chart. You can GOTO, EDIT
and ERASE a cursor waypoint.
Note: When in chart mode, if you place a waypoint at the cursor position, it is
not shown on the Fishfinder display.
If you place a waypoint at the vessel position in Fishfinder mode it is shown in
the chart window.
Placing a Waypoint
➤
MARKS
To access the place waypoint soft keys, press MARKS:
PLACE WPT PLACE WPT
AT CURSOR AT VESSEL
WAYPOINT
LIST
D4169-1
➤
To place a waypoint at the cursor position or at the vessel position:
1. Press either the PLACE WPT AT CURSOR or the PLACE WPT AT VESSEL soft
key. The waypoint is added to the waypoint list and tagged using the next
available number.
2. Press CLEAR or ENTER to remove the place waypoint soft keys.
Waypoints
Waypoints are described fully in Chapter 5. This section provides details that
are specific to placing Waypoints in Fishfinder mode.
4-12
hsb2 Plus Series Fishfinders
➤
To place a waypoint using the Waypoint List:
1. Press MARKS, followed by the WAYPOINT LIST soft key. The Waypoint List
and associated soft keys are displayed.
MARKS
u
WAYPOINT
LIST
WAYPOINT LIST
SYMBOL
NAME
WAYPOINT 001
WAYPOINT 002
Placing a Waypoint
WAYPOINT 003
WAYPOINT 004
WAYPOINT 005
POSITION
BRG _186°
TEMP
DATE
GOTO
WAYPOINT
---°C
--/--/--
EDIT
WAYPOINT
50°21^966N
001°20^368W
RNG _21.0nm
DEPTH
TIME
---m
--:--:--
MAKE NEW
WAYPOINT
WAYPOINT
TRANSFER
D4262-2
2. Press the MAKE NEW WAYPOINT soft key.
The waypoint is placed at the current vessel position, or if not available, the
cursor position. It is added to the Waypoint List and named with the next
available number.
MAKE NEW
WAYPOINT
To return to the default soft key display, press ENTER or CLEAR three times.
➤
To GOTO a cursor waypoint see Going To an Individual Target Point on
page 5-33.
➤
To ERASE a cursor waypoint see Erasing a Waypoint on page 5-15.
Chapter 4: Fishfinder Operations
4-13
4.7 MOB
If you lose a person or object overboard, and need to return to the location, you
should use the Man Overboard (MOB) function.
You can select the type of data used for the MOB position using the set up
menus (see Section 7.3).
Note: To obtain MOB position, you need either of the following:
• Position data from a GPS or equivalent device
➤
MOB
• Heading and speed data, so that the position can be calculated by dead
reckoning
To initiate the MOB procedure, press and hold the MARKS key for two
seconds. The system then performs the following tasks automatically:
MARKS
• Marks the Fishfinder image with a vertical line and the letters MOB.
• Marks the current position on the chart display with a MOB symbol
.
• Displays the MOB data box, showing the bearing and distance from your
vessel to the MOB waypoint position, and the elapsed time since the MOB
was initiated (Figure 4-4).
• Sounds a 4-second alarm pattern every 30 seconds.
• Sends an MOB message (including bearing and distance) to other units in
the system, via the SeaTalk connection.
MOB
52
60
80
MOB
0.33nm
BRG 162°T
00:05:24
RNG
FREQUENCY
POSITION
N 43°04^76
W070°44^83
ZOOM
BTM.LOCK
100
A-SCOPE
Figure 4-4:
➤
MARKS
MOB Display
To cancel the MOB, press and hold the MARKS key for 2 seconds.
The MOB symbol and data box are removed.
Note: The MOB procedure can also be initiated or cancelled if the appropriate SeaTalk message is received by the display unit.
4-14
hsb2 Plus Series Fishfinders
MOB
Chapter 5: Standard Chart Operations
5-1
Chapter 5: Standard Chart Operations
5.1 Introduction
This chapter explains how to navigate using the chart functions that are
available with the L755RC Plus, L760RC Plus, and L1250RC Plus Combined
Fishfinder/Chartplotter Displays. Chart functions are also available on L1250
Plus and L760 Plus fishfinder-only units, when connected to an hsb2 Plus
Series device with chartplotter functionality (see Section 2.7, Integrated
Systems). This chapter covers the following topics:
• Using chart cards
• Controlling waypoints, including placing, moving, editing and deleting
waypoints
• Following routes and going to waypoints
• Transferring Waypoints and Routes
• Using tracks, including showing tracks, track set up and saving tracks
All these chart functions are available in plotter mode, so you can plot and
track routes at large scales even when a chart card is not installed.
Further functions, including measuring distances and setting alarms are
described in Chapter 6.
Safety
The chartplotter makes it very easy to place a waypoint and travel towards it.
However, you should always check first that the route is safe. If you are using
the chartplotter in combination with a SeaTalk autopilot, the autopilot will
prompt for confirmation before it steers the vessel towards the waypoint.
If you have entered your route using a small-scale chart, zoom in to a larger
scale to check for hazards, such as small shoals, that may not be shown on the
smaller scale charts.
Note: Until you are familiar with interpreting the chart display, you should
take every opportunity to compare the displayed objects with visual targets,
such as buoys and coastal structures. You should practice harbor and coastal
navigation during daylight and in clear weather conditions.
Introduction
• Working with routes, including creating a new route, managing routes
using the route database and editing routes
5-2
hsb2 Plus Series Fishfinders
CAUTION:
The equipment should not be used as a substitute for good navigational
practice nor for official government paper charts.
5.2 Using Chart Cards
The chartplotter has a built-in world map; most areas are displayed on a scale
of 4000 nm from the top to the bottom of the screen, and can be zoomed in to
150 nm.
To use the chartplotter as a navigation aid, charts with detailed information for
the area you wish to navigate are required. The charts are available on C-MAP
NT and NT+ electronic chart cards (C-Cards), each of which can store as
many as 20 charts in an electronic format. A single C-MAP chart normally
provides as much information as is available in paper charts for that
geographic area, and can be displayed down to a range of 1/64 nm on the
screen if the data is available.
Using Chart Cards
Two card slots are provided on the display unit. Chart data from both slots can
be downloaded.
The chart scale in use is indicated in the status bar - the number represents the
distance (in nautical miles) displayed from the top of the screen to the bottom
of the screen.
Note: You can remove and insert cards while a chart is displayed. The chart
information is retained on-screen until the chartplotter redraws the screen:
for example, when you pan outside the current area, or use the RANGE key to
change the chart scale.
Data on a chart card is also available to a repeater display, which can be used
independently of the master. When the master display is switched off chart
data is retained on the repeater screen until the chart is redrawn.
Inserting a Chart Card
➤
To insert a chart card:
1. Check that the card is a C-MAP NT or NT+ C-Card with the required chart
stored on it.
2. Open the card cover, at the lower left of the display front panel.
3. Hold the card with the title label towards the left, as shown in the illustration.
4. Gently push the card into one of the two slots. The card will only go in if it
is correctly oriented. Push the card in as far as it will go, then move it to the
right so that the top is under the retaining pegs. The card will be held in
place by the pegs.
Chapter 5: Standard Chart Operations
5-3
D4158-2
Figure 5-1:
Inserting the Chart Card
Removing a Chart Card
➤
To remove a chart card:
1. Open the card cover, at the lower left of the display front panel.
2. Press on the card you wish to remove, and move the top of the card to the
left to clear the retaining pegs.
The card will spring half-way out, enabling you to grip the card and
remove it from the slot.
3. Remember to close the card cover so that it clicks shut, to prevent water
from entering the card reader assembly.
Displaying the Chart Data
The new chart information will be displayed when you move the cursor into an
area covered by the new chart or, if it is already in the area, change the range
scale.
If an hsb2 Plus Series repeater display is connected, the chart can also be
accessed by the repeater display. To see the chart you may need to zoom or
pan, to redraw the chart area to the screen.
Removing a Chart
Card
5. Close the card cover until it clicks shut, to prevent water entering the display unit.
5-4
hsb2 Plus Series Fishfinders
The boundary of each chart digitized in the current card is defined by a box or
rectangle. (You can switch off the chart boundaries display if you wish, as part
of the chartplotter set up described in Section 7.5.)
➤
To zoom in:
1. Use the trackpad to move the cursor inside one of the chart boxes, and press
the lower part of the RANGE key.
RANGE
That area is expanded, with the cursor at the center, so that you can see
more detail. Note that the smaller the chart box is on the screen, the further
you can zoom in and the greater the amount of detail that is available.
If you have switched on Plotter Mode (see Section 7.5), you can zoom in
further than the most detailed chart; all chart functions remain available.
Displaying Chart Object and Source Information
Displaying Chart
Object and Source
Information
Chart cards include a number of displayed objects for which information is
available, such as lights and buoys. They also contain additional source data
for structures, lines, open sea areas etc. You can use the context-sensitive
cursor to identify (in a pop-up box) an object or chart position and you can
obtain detailed information for the selected item.
Set up options let you specify when an identification pop-up is displayed;
three options are available:
• Display a pop-up for all objects and source data automatically when the
cursor is over the object symbol or source area.
• Display a pop-up for displayed objects when the cursor is over the symbol.
• Do not display the identification pop-ups.
The chartplotter also provides information for the nearest waypoint, port
facility, tide station, wreck or obstruction for a selected position. If your chart
includes port and tide data, this can be displayed.
➤ To identify and item and obtain detailed information:
1. Move the cursor over the symbol or chart position for which you require
the information. If specified in Chart Set Up, a pop-up box such as the following is displayed at the lower left or upper right corner of the screen:
1 Object
FAIRWAY BN Bn Safe Water RW
LFI.W.10s7m5M
D4260-2
2. To view detailed information, press ENTER. The details available are listed
on-screen in an object information pop-up.
The pop-up is split into two windows; objects are listed in the upper win-
Chapter 5: Standard Chart Operations
5-5
dow and details for the selected object are provided in the lower window.
Use the trackpad to select an object in the upper window and use the soft
keys to scroll up or down the detailed information in the lower window.
3. Press CLEAR to remove the pop-up from the screen and return to the
default display.
Port Area
At large chart scales port area information is indicated by the symbol . An
object information pop-up provides the name of the marina or port and a list of
the facilities available.
In some areas the chart shows symbols for individual facilities. The facilities
and their associated symbols are illustrated in Figure 5-2.
Figure 5-2:
Port Symbols
Displaying Chart
Object and Source
Information
Where available, details for each facility can be displayed. This information
includes items such as accommodation, slip sizes, fueling, sanitation,
electrical or other maintenance services provided, VHF channels monitored,
and other safety and navigation information.
5-6
hsb2 Plus Series Fishfinders
Tide Data
The symbol
indicates tide height data is available for that position on the
chart. When you select the tide height option, a graph of predictions for
maximum and minimum tide heights is displayed, data for sunrise and sunset
is also provided as illustrated Figure 5-3.
Note: The predictions available are sufficiently accurate under moderate
weather conditions, for the coastal areas served by the reference station, to be
used for navigation planning. However, certain weather fronts and storms
can alter tidal patterns and influence predicted times and heights.
The cursor, represented by a dotted vertical line on the graph, is used to select
a time for which the tide height is displayed.
You can use the soft keys and trackpad to change the date for which tide
information is shown.
Displaying Chart
Object and Source
Information
CSR N 43°04^84
POS W070°44^83
24nm
PORTSMOUTH, N.H.
8.50
7.05
5.60
4.15
2.70
1.25
-0.20
0
2
4
6
8
10 12 14 16 18 20 22 24
CURSOR
TIME
05:37am
HEIGHT 1.41ft
SUNRISE/SUNSET
TWILIGHT
0805
SUNRISE
0919
SUNSET
2359
TWILIGHT
----
SET DATE
PREV. DAY
SELECTED DATE
05/14/2000
HIGH/LOW WATER
HIGH 0040 8.46ft
LOW 0700 0.10ft
HIGH 1310 8.43ft
LOW 1930 -0.20ft
TODAY
NEXT DAY
D5035-1
Figure 5-3:
Tide Data
Chapter 5: Standard Chart Operations
5-7
➤
To select a time, use the trackpad to move the cursor to the required time.
➤
To change the day press PREV. DAY, DAY or TODAY, as required. Alternatively,
press SET DAY; to change date, use the trackpad to move the cursor left/right to
select the character and up/down to increase/decrease the value.
The graph and tide data will be updated accordingly.
Nearest
You can obtain information for the eight nearest waypoints, port services,
ports, tide stations, wrecks, or obstructions for a selected position. The
chartplotter also provides options to redraw the chart with a selected item at
the center, Goto a waypoint and display a list of all the port on the chart card.
To obtain the information for the nearest objects:
1. Move the cursor to the required position, and then press ENTER to display
the object information pop-up.
2. Press the NEAREST soft key. The Find Nearest pop-up list is displayed.
Use the trackpad to highlight the required object, and then press ENTER.
i. For port services the port service symbols are displayed. Use the trackpad to highlight the required service, and then press ENTER.
If you select a port then press ENTER, detailed information for the service at that port are displayed.Typical port data is shown in Figure 5-4.
D4255_1
Figure 5-4:
Nearest Port - Typical Data
ii. For all other items, the eight nearest objects are listed with distance and
bearing.
Displaying Chart
Object and Source
Information
➤
5-8
hsb2 Plus Series Fishfinders
Soft keys provide you with options to EXPAND port, wreck and obstructions data; view a FULL LIST of ports detailed on the chart card; SHOW
TIDE data; GOTO a waypoint and FIND the object (redraw the chart with
the object at the center). Use the trackpad to highlight an object, then
press the required soft key.
3. To return to the default display, press CLEAR to back-track through the
pop-up lists.
5.3 Working with Waypoints
Introduction
Working with
Waypoints
The Chartplotter enables you to place up to 998 waypoints. (Waypoint number
999 is used for MOB operation.) A waypoint is a position entered on a chart as
a reference, or as a place to go to. All waypoints placed on the chartplotter are
stored in a waypoint database list, which includes symbol, position, bearing,
range and additional data. All waypoints in the database are displayed on the
screen, unless you set waypoint display off in the Chart Set Up menu, as
described in Chapter 7. You can select a waypoint, either on-screen or from
the list, for editing.
A waypoint can be placed at the cursor position or at the vessel’s current
position (sometimes known as an event mark). A waypoint at the vessel
position includes additional information (if available) on the depth and
temperature when it was placed. Alternatively, you can manually enter
Waypoints as either Lat/Long coordinates or Loran TDs which are
automatically converted into Lat/Long coordinates. All waypoints can be
included in a route. You can place waypoints, using simulator mode, before
you install the chartplotter on your vessel.
Note: Radar marks may also be displayed on the screen if your chartplotter is
part of an integrated system; these are screen annotations - you cannot go to
marks, nor can they be included in routes.
When you place a new waypoint, it is displayed using the default symbol of a
cross (unless you have changed the symbol in Chart Set Up). The waypoint is
added to the waypoint list and tagged with the next available number. You can
use the edit functions to change the symbol and name. When the cursor is
positioned over a waypoint, the waypoint bearing and range are displayed.
Waypoints in the current route are available on other SeaTalk instruments that
support current route transfer, for example, another hsb2 Plus Series
Chartplotter or the ST80 Masterview. You can also transfer waypoints
between the chartplotter and other NMEA or SeaTalk instruments using the
Waypoint Transfer functions.
This section explains how to perform the following tasks using the on-screen
cursor and the waypoint list:
Chapter 5: Standard Chart Operations
5-9
• Placing a Waypoint
• Selecting a Waypoint
• Displaying Waypoint data
• Editing a Waypoint (symbol, name & position)
• Erasing a Waypoint
• Moving a Waypoint
At the end is a section about using the ST80 Navigator Keypad to select, edit,
and name your waypoints.
Placing a Waypoint
The scenario Place and Goto a Waypoint on page 5-44 provides a simple
example of how to place a waypoint.
MARKS
MARKS
PLACE
PLACE WPT
WPT PLACE
PLACE WPT
WPT WAYPOINT
WAYPOINT LOAD/SAVE
AT
LIST
USER CARD
AT CURSOR
CURSOR AT
AT VESSEL
VESSEL
LIST
D5572-1
D4169-1
➤ To place a waypoint at the cursor position or at the vessel position:
PLACE WPT
AT CURSOR
PLACE WPT
AT VESSEL
1. Press either the PLACE WPT AT CURSOR or the PLACE WPT AT VESSEL soft
key. The waypoint is added to the waypoint list and tagged using the next
available number.
The waypoint soft keys are displayed until you move the cursor away from
the waypoint or press CLEAR.
GOTO
WAYPOINT
EDIT
WAYPOINT
ERASE
WAYPOINT
MOVE
WAYPOINT
D4163-1
You can use the EDIT WAYPOINT soft key to name the waypoint as
described in Editing Waypoints below.
2. Press CLEAR or ENTER to remove the place waypoint soft keys.
➤ To place a waypoint as latitude/longitude using the Waypoint List:
MARKS
WAYPOINT
LIST
1. Press MARKS, followed by the WAYPOINT LIST soft key. The Waypoint List
and associated soft keys are displayed.
Placing a Waypoint
➤ To access the place waypoint soft keys, press MARKS:
5-10
hsb2 Plus Series Fishfinders
WAYPOINT LIST
SYMBOL
NAME
WAYPOINT 001
WAYPOINT 002
WAYPOINT 003
WAYPOINT 004
WAYPOINT 005
POSITION
BRG _186°
TEMP
DATE
Placing a Waypoint
GOTO
WAYPOINT
50°21^966N
001°20^368W
RNG _21.0nm
---°C
DEPTH
---m
--/--/--
TIME
--:--:--
EDIT
WAYPOINT
MAKE NEW
WAYPOINT
WAYPOINT
TRANSFER
D4262-2
MAKE NEW
WAYPOINT
2. Press the MAKE NEW WAYPOINT soft key followed by the LAT/LONG soft
key; the WPT POSITION (LAT/LONG) screen is displayed, with it’s associated
soft keys. The waypoint is placed at the current vessel position, or if not
available, the cursor position.
3. You can use the soft keys to edit the waypoint position as described in Editing the Waypoint Details on page 5-13.
It is added to the Waypoint List and named with the next available number.
To return to the default soft key display, press ENTER or CLEAR twice.
➤ To place a waypoint as Loran TDs using the Waypoint List:
1. Press MARK, followed by the WAYPOINT LIST soft key; the Waypoint List
and associated soft keys are displayed.
2. Press the MAKE NEW WAYPOINT, the waypoint is placed at the current vessel position, or if not available, the cursor position. To change the position
press the LORAN TDs soft key; the WPT POSITION (LORAN TDs) screen is displayed, with it’s associated soft key:
Chapter 5: Standard Chart Operations
5-11
WPT POSITION (LORAN TDs)
CHAIN
6731 - NELS Lessay
SLAVES
Y - Z (24 -39)
TD 1
29138.0
TD 2
44713.8
ASF 1
+0.0
ASF 2
+0.0
CHAIN
ASF1/ASF2
SET TD 1
SET TD 2
Note: You can enter waypoints as Loran TDs which are converted to Lat/
Long coordinates. However, although the waypoint is shown in both Lat/
Long and Loran TDs in the Waypoint List, you can subsequently only edit
the position as Lat/Long coordinates. TD entries in the Waypoint List are
shown only for those waypoints which were entered as TDs.
3. Edit the Loran parameters as required, using:
i. The CHAIN soft key, which enables selection of both the Chain and it’s
Slave:
WPT POSITION (LORAN TDs)
CHAIN
6731 - NELS Lessay
SLAVES
Y - Z (24 -39)
TD 1
29138.0
TD 2
44713.8
ASF 1
+0.0
ASF 2
+0.0
SELECT
CHAIN
SELECT
SLAVES
D5592-1
ii. The ASF1/ASF2 soft key, which presents two soft keys for editing ASF 1
and ASF 2 parameters independently:
SET ASF 1 SET ASF 2
D5593-1
iii. The SET TD 1 and SET TD 2 soft keys, which enable editing of each TD’s
parameters independently.
Placing a Waypoint
D5591-1
5-12
hsb2 Plus Series Fishfinders
Note: Except for the CHAIN setting, parameters are edited using the trackpad
as described in Editing the Waypoint Details on page 5-13.
4. When editing is complete, press the ENTER key to save the waypoint or
CLEAR to cancel the operation; the display returns to the New Waypoint
screen.
Press the ENTER or CLEAR to return to the Waypoint List.
Selecting a Waypoint
Positioning the cursor over a waypoint selects that waypoint and accesses the
waypoint soft keys. These keys enable you to GOTO (described in Section 5.5),
EDIT (symbol, name, position), ERASE or MOVE the waypoint.
Selecting a waypoint from the List allows you to GOTO and EDIT (symbol,
name, position, erase) the waypoint. The Waypoint List also provides options
to make a new waypoint and transfer waypoints.
➤
To select a waypoint using the cursor:
Selecting a
Waypoint
1. Move the cursor over the waypoint, until the letters WPT are displayed.
The Waypoint Data box (see Waypoint Data Display on page 5-13) and the
following soft keys are displayed:
WPT
GOTO
WAYPOINT
EDIT
WAYPOINT
ERASE
WAYPOINT
MOVE
WAYPOINT
D4163-1
The selected waypoint can be edited via these soft keys.
➤
MARKS
WAYPOINT
LIST
To select a waypoint using the Waypoint List:
1. Press MARKS, followed by the WAYPOINT LIST soft key.
The Waypoint List and associated soft keys are displayed.
The list details all waypoints in alpha-numeric order. The selected waypoint is indicated by the selection bar; its position, bearing and range are
provided.
2. Use the trackpad to move the selection bar up and down the list to highlight
the required waypoint.
or
Use the ST80 Navigator to select to highlight the required waypoint, as
described in Using the ST60 or ST80 Navigator Keypad on page 5-16.
The selected waypoint can be edited via the soft keys displayed.
Chapter 5: Standard Chart Operations
5-13
Waypoint Data Display
Waypoint data can be viewed in two ways: you can use the context-sensitive
cursor to select the waypoint and thus display the waypoint data box, or you
can view waypoint details on the waypoint list.
Note: To permanently display the target waypoint data box, select it in the System Set Up menu (see Section 7.3) and use the SCREEN soft key to switch data
boxes on.
➤
To display the waypoint data box, move the cursor over the waypoint.
The waypoint data box is displayed, this indicates waypoint number/name,
bearing and range (or latitude and longitude if selected in the system set up
menu).
WAYPOINT 001
191oT
2.2nm
D4250-1
While the cursor is over the waypoint, the waypoint soft keys are displayed.
➤
To remove the waypoint data box and soft keys either:
Move the cursor away from the waypoint, or press CLEAR.
➤
To display the waypoint details from the waypoint list:
Select the waypoint in the list as described above.
The details for the selected waypoint are displayed in the lower half of the
window. Temperature, depth, date and time are included (if available) for
waypoints placed at the vessel position.
MARKS
WAYPOINT
LIST
To remove the Waypoint List and return to the default soft key display, press
CLEAR twice.
Editing the Waypoint Details
You can change the name, symbol and position of any waypoint.
➤
To edit a waypoint:
1. Select the waypoint, using the cursor or the waypoint list, as previously
described. The waypoint soft keys are displayed.
EDIT
WAYPOINT
2. Press the EDIT WAYPOINT soft key. The Edit Waypoint soft keys are displayed:
SYMBOL
NAME
POSITION
D4166-1
3. To edit the symbol, press the SYMBOL soft key.
Waypoint Data
Display
BRG
RNG
5-14
hsb2 Plus Series Fishfinders
Use the soft keys, shown in the following illustration, to highlight the
required symbol, then press ENTER to confirm the selection.
Press ENTER or CLEAR to return to the default soft keys.
SELECT SYMBOL
D4178-1
4. To edit the waypoint name, press the NAME soft key. The NAME WAYPOINT
window is displayed.
Using the trackpad to edit the name:
iv. Use the left or right side of the trackpad to move the cursor to the character you wish to change.
Editing the
Waypoint Details
v. Then use the top or bottom of the trackpad to scroll through the characters.
Using the ST80 Navigator Keypad to edit the name:
i. Use the left or right arrows of the Navigator’s keypad to move the cursor to the character you wish to change.
ii. Use the up and down arrow keys to scroll through the characters.
or
Use the alphanumeric keypad to change the character, as described in
Using the ST60 or ST80 Navigator Keypad on page 5-16
When you have finished editing the name, to remove the window, press
ENTER to save the name or CLEAR to cancel the operation. The waypoint
name replaces the waypoint number.
Press ENTER or CLEAR to return to the default soft keys.
EDIT
WAYPOINT
5. To edit the waypoint position, press the EDIT WAYPOINT soft key, followed
by POSITION. The Waypoint Position pop-up is displayed.
Use the soft keys to select LAT, LON, BRG or RNG.
Using the trackpad to edit the value:
i. Use the left or right side of the trackpad to move the cursor to the character you wish to change.
ii. Use the top or bottom of the trackpad to scroll through the characters.
iii. Adjust each parameter until the waypoint position is correct.
Using the ST80 Navigator Keypad to edit the value:
i. Use the left or right arrows of the Navigator’s trackpad to move the cursor to the character you wish to change.
ii. Use the up and down arrow keys to scroll through the characters.
Chapter 5: Standard Chart Operations
5-15
or
Use the alphanumeric keypad to change the character. Press the def/2
key for East, mn/5 for North, rst/7 for South, and uvw/8 for West.
iii. Adjust each parameter until the waypoint position is correct.
When you have finished editing the position, press ENTER to save the position
or CLEAR to cancel the operation.
Press ENTER or CLEAR again, the Waypoint Position window is removed
from the screen and the default soft keys are displayed.
You cannot erase the target waypoint or waypoints that are used in routes.
However, you can remove a waypoint from the current route - see Editing a
Route on page 5-28.
If you try to erase a waypoint that is used in a saved route you are warned
“WAYPOINT IS USED IN A ROUTE & CANNOT BE DELETED”
➤
To delete a waypoint using the cursor:
1. Move the cursor over the waypoint, until the letters WPT are displayed. The
waypoint soft keys are displayed.
WPT
2. Press the ERASE WAYPOINT soft key. The waypoint is removed from the
screen and the Waypoint List is updated.
ERASE
WAYPOINT
Note: If you have stopped a GOTO (see Stop Follow or Stop Goto on
page 5-34), the target waypoint remains displayed as a target; you need to use
the CLEAR GOTO soft key before you can erase the waypoint using the cursor.
➤
MARKS
WAYPOINT
LIST
To delete a waypoint using the waypoint list:
1. Select the waypoint from the waypoint list as previously described. The
waypoint list soft keys are displayed.
2. Press the EDIT WAYPOINT soft key, followed by ERASE WAYPOINT. The waypoint is removed from the screen and the waypoint list is updated.
Moving a Waypoint
You can move any waypoint except the target waypoint (the waypoint you are
following). You can use the Waypoint soft keys and cursor to move the
selected waypoint, or you can edit the waypoint position.
CAUTION:
Take care when editing waypoints as it is possible to move waypoints that are
used in routes stored in the Route Database. List.
Erasing a Waypoint
Erasing a Waypoint
5-16
hsb2 Plus Series Fishfinders
➤
To move a waypoint using the cursor:
1. Move the cursor over the waypoint, until the letters WPT are displayed. The
waypoint soft keys are displayed.
WPT
MOVE
WAYPOINT
2. Press MOVE WAYPOINT, the cursor changes to a four-headed arrow.
3. Move the cursor to the required waypoint position.
Press ENTER to set the position and return to normal cursor control.
Press CLEAR to cancel the operation.
➤
To move a waypoint using the Waypoint Edit functions:
1. Select the waypoint using either the cursor or the waypoint list as described
above. The waypoint soft keys are displayed.
2. To edit the waypoint position proceed as previously described in Editing
the Waypoint Details on page 5-13.
Using the ST60 or ST80 Navigator Keypad
Using the ST60 or
ST80 Navigator
Keypad
If you have an ST60 or ST80 Navigator Keypad connected on SeaTalk it can
be used to name or edit your waypoints, tracks, or routes on any display in the
system. The keypad can also be used to select entries in the Waypoint List. The
Navigator provides 10 dedicated alphanumeric keys, a multidirectional cursor
control pad, plus Insert and Delete keys.
Note: When using the Navigator Keypad, you should be aware that it can control several displays simultaneously; any display in edit mode (i.e. ready for
alpha-numeric data entry) will be affected by the Navigator Keypad.
1
abc
2
def
3
ghi
4
jkl
5
mn
6
opq
7
rst
8
uvw
9
xyz
ins
0
del
NAVIGATOR
D1934-2
Figure 5-5:
ST60/ST80 Navigator Keypad
Most of the alphanumeric keys are used to input multiple characters. Each
time you press one of these keys in succession, the next character on that key is
input. For example, each press of the 1 key alternately inputs A, B, C, then 1.
Chapter 5: Standard Chart Operations
5-17
The Navigator’s arrow keys function much like the fishfinder’s trackpad,
enabling you to move the cursor position or input alpha, numeric, or special
characters ( . , - / ‘ & ).
The ins key functions the same as the ENTER key on fishfinder and del inserts
a space during edit mode.
Selecting an Entry in the Waypoint List
The Navigator can be used to select an existing item in the Waypoint List. This
can be accomplished using the arrow or alphanumeric keys.
To select an existing item in the Waypoint List:
1. Use the up and down arrow keys to move the selection bar up and down the
list to highlight the desired entry, just as you would with the fishfinder’s
trackpad.
or
Press the alphanumeric key that contains the first letter or number of the
desired waypoint name. The selection bar moves to the entry starting with
that letter or number.
If more than one entry begins with that character, the selection bar moves
to the first one in the list. Each time the same key is pressed, the selection
bar moves to the entry starting with the next character on the key. If no
entry exists for that character, the entry starting with the nearest previous
character is selected. If the numeric value of the key is input when no
numeric entry exists, the selection bar moves to the first alpha entry.
For example, let’s say we have four waypoints named ORION,
POLARIS, QUANTUM, and 6-GUN. Pressing the opq/6 key four successive times would select the waypoints ORION (O), POLARIS (P),
QUANTUM (Q), then 6-GUN (6). However, pressing the rst/7 key four
successive times would select QUANTUM for the first three key presses
because entries beginning with the associated letters do not exist and Q is
the next previous beginning letter. The fourth press of the rst/7 key would
select 6-GUN because no entries begin with a 7 and 6 is the next previous
beginning number.
2. Use the ins key like the fishfinder’s ENTER key, to close the Waypoint
List.
The del key and left and right arrow keys do not function in select mode.
Using the ST60 or
ST80 Navigator
Keypad
➤
5-18
hsb2 Plus Series Fishfinders
Editing Entries in the Waypoint, Route, or Track Lists
You can also use the ST80 Navigator Keypad to edit an existing item or to
name a new item in the Waypoint List, Route List, or Track List. You first must
enter the edit mode for the list you want to modify. Methods for editing each
list are described in the respective sections of this chapter.
➤
To edit an item in a list using the Navigator:
1. If necessary, use the right and left arrow keys to move the cursor to the
desired character position.
2. Press an alphanumeric key until the desired character is displayed. Each
time you press one of these keys in succession, the next character on that
key is input.
or
Working with
Routes
Use the up and down arrow keys to scroll through the list of alpha,
numeric, and special characters until the desired character is displayed
(just as you would with the fishfinder’s trackpad). Note that you must use
this method to input special characters; they are not available using the
alphanumeric keys.
Use the del key to insert a space, if required.
3. Use the arrow keys and alphanumeric keys to input the remainder of the
characters required to complete the editing.
4. When done, press the ins key to enter your changes.
5.4 Working with Routes
A route is made up of a series of waypoints (maximum 50). To make a route
you place a series of waypoints on the chart.
When a route is created it becomes the current route and is displayed onscreen. The current route is maintained when you power-off. Only one route
can be current and is displayed (if it is in the field-of-view) as solid lines
connecting waypoints. If you are following the route, the current leg is shown
as a dotted line and previous legs are removed from the screen (although the
waypoints remain displayed). The current route (and its waypoints) is
transferred via SeaTalk to a repeater chart display and other instruments. You
can also use the Waypoint Transfer functions to transfer the route database to a
repeater display.
Once you have created a route you can use the GOTO soft keys to follow the
route. In addition, the GOTO default soft key provides various options as
described in Section 5.5.
Chapter 5: Standard Chart Operations
5-19
Up to 20 routes can be saved in the route database. You can then select a route
from the database list as the current route.
The current route can be edited by adding and moving waypoints. The current
route is always placed in the database list as route number 0, so you can edit the
current route without affecting the original route in the database. Once a route
has been saved, options are also provided to name a route, erase a route and to
display route details.
You can use the route information to review your passage plan by adjusting the
planned Speed Over Ground (SOG).
This section explains how to perform the following tasks:
• Creating a new route.
• Saving the current route in the database list.
• Clearing the current route.
• Retrieving a route from the database list as the current route.
• Displaying route information, including the route leg data and waypoint
details. Use the waypoint details to review your passage plans for different
speeds.
• Using the database list to erase and name existing routes.
• Editing a route by adding, removing and moving waypoints.
➤
ROUTE
To access the route soft keys, press the default soft key ROUTE:
MAKE
ROUTE
EDIT
ROUTE
CLEAR
ROUTE
MORE!
D4167-1A
Creating a New Route
Note: If there is a current route, it is cleared when you select MAKE ROUTE. If
you are following the current route you are prompted to STOP FOLLOW. Press
the YES soft key to continue, or NO to abandon route creation. If the route has
not been saved you are prompted to save it.
The chart scenario Make and Follow a Route on page 5-46 provides a simple
example of how to create a route.
Creating a New
Route
Note: The route database is stored locally, in the display unit on which it was
created. Although the current route is automatically transferred, you need to
use the WAYPOINT TRANSFER function, described in Section 5.6, to transfer the
complete route database to a repeater display connected via hsb2.
Also, it is possible for the current route to be overwritten by a route from another unit on an integrated system, so it is advisable to save all routes.
5-20
hsb2 Plus Series Fishfinders
You can edit a route after you have finished making it, as described in Editing
a Route on page 5-28.
➤
To make a new route by placing waypoints:
Note: You can pan the chart and change the scale while placing waypoints.
1. If necessary, move the cursor to the area in which you wish to make the
route, and select a suitable chart scale.
ROUTE
MAKE
ROUTE
2. Press the ROUTE soft key, then press the MAKE ROUTE soft key. The make
route soft keys are displayed:
PLACE
WAYPOINT
UNDO
WAYPOINT
ACCEPT
ROUTE
USE
WPT LIST
D5575-1
PLACE
WAYPOINT
3. Move the cursor to the position on the chart where you want your first waypoint to be. Press the PLACE WAYPOINT soft key.
Creating a New
Route
Note: You can position the cursor on an existing waypoint – the text WPT indicates you are re-using the waypoint rather than placing a new one. This waypoint is included in the route when you press PLACE WAYPOINT.
The waypoint appears on the screen at the cursor position. The number
displayed alongside the waypoint identifies its position in the route. The
new waypoint is temporarily added to the waypoint list with the first available waypoint number. The waypoints in the current route are re-numbered to identify the new positions.
Note: If you Clear the route before it is Saved, the waypoint is removed.
4. Move the cursor to the next waypoint position. A dotted line connects the
cursor to the last placed waypoint.
PLACE
WAYPOINT
UNDO
WAYPOINT
5. Press PLACE WAYPOINT again. The waypoint is placed and the dotted line
changes to a solid line.
If you placed the waypoint incorrectly, you can delete the last-placed waypoint by pressing the UNDO WAYPOINT soft key.
6. Repeat steps 4 and 5 until you have placed all your waypoints. You can
have up to 50 waypoints in a route.
7. When you have entered all your waypoints, either:
ACCEPT
ROUTE
Press the ACCEPT ROUTE soft key (or ENTER) to complete the route. Your
route is displayed on the screen, and is the current route, but it is not active.
The first waypoint of a new route is outlined with a square, indicating that
it will be the target waypoint when the route is activated. If selected, the
waypoint data box is displayed for the target waypoint.
Chapter 5: Standard Chart Operations
➤
ROUTE
5-21
To make a new route using the Waypoint List:
1. Press the ROUTE soft key; the route soft keys are displayed.
MAKE
ROUTE
EDIT
ROUTE
CLEAR
ROUTE
MORE!
D4167-1A
MAKE
ROUTE
2. Press the MAKE ROUTE soft key; the make route soft keys are displayed
PLACE
WAYPOINT
UNDO
WAYPOINT
ACCEPT
ROUTE
USE
WPT LIST
D5575-1
USE
WPT LIST
3. Press the USE WPT LIST soft key; the MAKE ROUTE screen is displayed with
its associated soft keys.
WAYPOINTS
NEW ROUTE
COWES
GURNARD LEDGE
MAIN CHANNEL
NEEDLES FAIRWAY
PORT SOLENT
50°50^000N
001°06^000W
50°52^230N
001°02^390W
348°m
300°m
INSERT
WAYPOINT
2.30nm
REMOVE
WAYPOINT
01
02
03
04
HARBOUR
MAIN CHANNEL
COWES
LYMINGTON
ACCEPT
ROUTE
1.00nm
USE
CURSOR
D5574-1
The available Waypoints are listed in the left hand column (alphanumeric); the
right hand column lists the waypoints in the New Route, the number indicates
its order in the route. The lower part of the table shows position, bearing and
range of the highlighted waypoint.
You use the trackpad left/right to move control between the two columns (the
highlighted title indicates the selected column) and the trackpad up/down to
scroll through the lists.
4. Select a waypoint from the Waypoint List then go to the New Route column and select a position in the list.
Note: A waypoint cannot be used more than once in a route; those already
used are displayed in a lighter shade of gray.
INSERT
WAYPOINT
5. Press the INSERT WAYPOINT soft key to place the waypoint below the
selected position in the Route. You can have up to 50 waypoints in a route.
Creating a New
Route
MAKE ROUTE
5-22
hsb2 Plus Series Fishfinders
6. To remove a waypoint from the New Route column, highlight the waypoint and press the REMOVE WAYPOINT soft key.
REMOVE
WAYPOINT
Note: The INSERT WAYPOINT or REMOVE WAYPOINT action adds/removes the
highlighted waypoint to/from the Route column, regardless of which column
is selected.
7. When all waypoints have been entered, press the ACCEPT ROUTE soft key
(or ENTER) to complete the route.
ACCEPT
ROUTE
Note: The completed route is stored in the display unit and will be re-displayed if you turn the unit off then on again. However, on an integrated system
it is possible for a current route from another unit to overwrite this route; it is
therefore recommended that you save the route, as described in Saving the
Current Route.
Saving the Current Route
Saving the Current
Route
You can save up to 20 named routes in the route database list. These routes can
then be re-displayed and followed at a later date. When you save the route, all
new waypoints are saved in the Waypoint List.
Note: If the current route has not been saved, when you attempt an operation
that affects this route, e.g., CLEAR ROUTE, you are prompted to save it.
➤
To save and name the current route:
ROUTE
1. To access the SAVE ROUTE soft key, press the ROUTE soft key, followed by
MORE.
SAVE
ROUTE
2. Press the SAVE ROUTE soft key. The save route pop-up and the NAME ROUTE
soft keys are displayed as illustrated in Figure 5-6.
3. The next available entry on the route list is highlighted.
(If required, you can use the trackpad to select another position in the list;
this can be a blank slot, or an existing route that you no longer require).
Chapter 5: Standard Chart Operations
5-23
SAVE ROUTE
1
EMPTY
2
EMPTY
3
EMPTY
4
EMPTY
5
EMPTY
NAME ROUTE?
NO
D4155-1
Figure 5-6:
Save Route Window
4. If you do not wish to name or re-name the route, press the NO soft key to
clear the list. The route is saved and is listed as Route Not Named.
5. If you wish to name the route press the YES soft key:
Use the trackpad to move the cursor right or left to the character you wish
to edit. Then use the top or bottom of the trackpad to increase or decrease
the letter or number.
or
Use the arrow keys and alphanumeric keys on the ST80 Navigator keypad
to input or edit the characters, as described in Using the ST60 or ST80
Navigator Keypad on page 5-16.
6. Press ENTER to finish and clear the Name List, or press CLEAR to cancel
the operation. To return to the default soft key display, press ENTER again.
Saving the Current
Route
YES
5-24
hsb2 Plus Series Fishfinders
Clearing the Current Route
You can clear the current route from the screen. When you select CLEAR ROUTE
if the current route has not been saved, you have the option of saving it and, if
you are following the current route, you have the option to stop.
➤
To clear the current route:
1. Press the ROUTE default soft key or place the cursor over a route leg until
the text RTE is displayed.
Press the CLEAR ROUTE soft key.
ROUTE
RTE
2. If you are following the current route the STOP FOLLOW soft keys are displayed.
To cancel the CLEAR operation press NO.
To stop following and clear the route press YES.
STOP
FOLLOW
3. If the route has not been saved the SAVE ROUTE soft keys are displayed.
To clear the route, without saving it in the route database, press NO.
To save the route in the database, press YES. The Name route soft keys are
displayed and you should continue as described in the previous section,
Saving the Current Route on page 5-22.
SAVE
ROUTE
Clearing the
Current Route
The current route is cleared from the screen and the default soft keys are
displayed. You can now use the ROUTE soft keys to make a route, or to show
another route from the database.
Retrieve a Route From the Database
You can select a route as the current route from the database list. The list is
accessed from the second set of ROUTE soft keys.
➤
ROUTE
SHOW
ROUTE
To select a route as the current route:
1. Press the ROUTE soft key, followed by MORE, then press ROUTE LIST. The
route list is displayed as illustrated in Figure 5-7. The selection bar indicates the selected route.
2. Use the trackpad to select the required route then press the SHOW ROUTE
soft key. The chart is re-drawn at a scale suitable to display the whole route.
Chapter 5: Standard Chart Operations
5-25
ROUTE LIST
CURRENT
1
EMPTY
2
EMPTY
3
EMPTY
4
EMPTY
SHOW
ROUTE
ERASE
ROUTE
ROUTE
INFO
NAME
ROUTE
Figure 5-7:
Route List Window
Displaying Route Information
You can display the following information that relates to your route:
• Route leg or waypoint information, using the context-sensitive cursor.
• Details of waypoints in the route, using the soft keys. You can use this
information to review your passage plan.
Route Leg and Waypoint Information
➤
RTE
To display information about a route leg, move the cursor over the leg until the
letters RTE are displayed. A Route Leg data box such as the following is
displayed.
ROUTE NO.
ROUTE NAME
LEG 02 - 03
0°T
5.5nm
D4259-2
To remove the data box, move the cursor away from the route or press CLEAR.
➤
WPT
To display information about a route waypoint, move the cursor over the
waypoint until the letters WPT are displayed. The waypoint data box is
displayed, this box includes the route and waypoint number.
To remove the data box, move the cursor away from the route or press CLEAR.
Displaying Route
Information
D4263-1
5-26
hsb2 Plus Series Fishfinders
Using Route Information to Review Your Passage Plan
You can view data for all the waypoints in the current route, or any saved route.
You select the route from the database list and the information is displayed in a
Route Information pop-up; the following details are provided for each
waypoint:
• Position
• Bearing (from previous waypoint)
• Length of leg (from previous waypoint)
• Total Length
• Time (ETA or Elapsed)
Displaying Route
Information
Soft keys are provided to toggle the time between ETA or elapsed and to
change the Speed Over Ground (SOG) value; the ETA for each waypoint is
calculated using the selected SOG, so you can change the SOG to determine its
effect on your ETA.
The chart scenario Review Your Passage Plan on page 5-48 provides a simple
example of how to use the route information.
➤
To display information about any route in the database:
1. Press the ROUTE soft key, followed by MORE, then press ROUTE LIST. The
route list is displayed. The selection bar indicates the selected route.
ROUTE
2. Use the trackpad to select the required route, then press the ROUTE INFO soft
key.
The Route Information pop-up is displayed. As illustrated in Figure 5-8,
this lists the waypoints in the route and details bearing, length of each leg,
total distance, and either the estimated time of arrival (ETA) or the elapsed
time.
ROUTE
INFO
The soft keys allow you to toggle between ETA or total (elapsed) time,
and to change the Speed Over Ground (SOG) value used in the time calculations. The current selections are highlighted.
➤
To change the SOG used for ETA calculations:
1. Press one of the PLANNED SOG keys to switch from actual to planned SOG.
2. Press the up or down PLANNED SOG keys to change the planned SOG value.
The Time values in the Route Information list are updated.
3. Press the ACTUAL SOG key to use the actual SOG value rather than a
planned one.
Chapter 5: Standard Chart Operations
5-27
INFO FOR ROUTE-CURRENT ROUTE
WPT POSITION BRG DISTANCE TOTAL TIME
°T
01
50°21^97N ---
nm
nm
ETA
0.0
0.0 --:--
4.4
4.4 --:--
5.5
10.0 --:--
001°15^80W
02
50°21^97N 090
001°08^75W
03
50°27^48N 000
TIME
ETA TOTAL
ACTUAL
SOG
1.0kn
Using the Route List
to Erase and Name
a Route
001°08^75W
PLANNED SOG
0.0kn
D4264-1
Figure 5-8:
Route Information Window
4. Press ENTER to remove the Route Information window, then ENTER or
CLEAR to return to the route soft keys.
5. To return to the default soft key display, press ENTER.
Using the Route List to Erase and Name a Route
You can delete a route and you can re-name a route by selecting the route on
the route list.
➤
ROUTE
ERASE
ROUTE
To select a route to delete or re-name:
1. Press the ROUTE soft key, followed by MORE, then press ROUTE LIST. The
route list is displayed. The selection bar indicates the selected route.
Press the appropriate soft key – ERASE ROUTE or NAME ROUTE.
2. If you ERASE a route you are prompted to confirm.
Press NO to cancel the operation, then ENTER or CLEAR if you wish to
remove the route list.
Press YES to erase the route from the list, then ENTER or CLEAR to remove
the route list.
5-28
hsb2 Plus Series Fishfinders
3. If you NAME a route:
NAME
ROUTE
Use the trackpad to move the cursor right or left to the character you wish
to edit. Then use the top or bottom of the trackpad to increase or decrease
the letter or number.
or
Use the arrow keys and alphanumeric keys on the ST80 Navigator keypad
to input or edit the characters, as described in Using the ST60 or ST80
Navigator Keypad on page 5-16.
4. Press ENTER to clear the Name List, or CLEAR to cancel the name then to
return to the default soft key display, press ENTER again.
Editing a Route
Once you have created a route, you can edit it by:
• Inserting a Waypoint into the route
Editing a Route
• Adding waypoints at the end of the route
• Removing a Waypoint
• Reversing a Route
• Moving a Waypoint as described in Moving a Waypoint on page 5-15
Any changes you make to the route affect only the current route. The current
route is always held in position 0 in the database, so you need to Save the route
if you want to keep the changes.
Inserting a Waypoint into a Route
You can use the context-sensitive cursor to insert one or more waypoints in the
current route. However, if the route is being followed you cannot insert a
waypoint into the current leg.
➤
RTE
To insert a new waypoint in the current route:
1. Move the cursor over the route leg into which you wish to insert a waypoint. The letters RTE and the route leg data box are displayed. The Route
soft keys are displayed.
2. Press ENTER. The cursor changes to a four-way arrow, controlling a new
waypoint. The waypoint is connected to the existing waypoints on either
side with a dashed line.
3. Move the new waypoint to the required position, and press ENTER to drop
it and return to normal cursor operation, or CLEAR to cancel the operation.
The new waypoint is temporarily added to the waypoint list and named with
the first available waypoint number. The waypoints in the current route are renumbered to identify the new positions.
Chapter 5: Standard Chart Operations
5-29
Note: If you Clear the route before it is Saved, the new waypoint is removed.
Adding Waypoints at the End of the Route
➤
To add waypoints at the end of the route:
1. Press the ROUTE soft key, followed by the EDIT ROUTE soft key.
The Make Route soft keys are displayed and the cursor is connected to the
last-placed waypoint with a dotted line. You can add further waypoints to
the route in the same way as for a new route.
ROUTE
EDIT
ROUTE
2. Move the cursor to the required location, and press PLACE WAYPOINT soft
key.
If you place the waypoint in the wrong position, press the UNDO WAYPOINT
soft key.
PLACE
WAYPOINT
UNDO
WAYPOINT
3. Place as many waypoints as required, and press the ACCEPT ROUTE soft key,
the default soft keys are displayed.
ACCEPT
ROUTE
Removing a Waypoint from the Route
➤
To remove a waypoint from the current route:
1. Move the cursor over the required waypoint until the letters WPT are displayed. The waypoint soft keys are displayed.
WPT
2. Press the REMOVE WAYPOINT soft key. The waypoint is removed from the
route and the route is re-numbered.
REMOVE
WAYPOINT
Alternatively, you can remove the last waypoint from a route by pressing the
UNDO WAYPOINT soft key, as described above in Adding Waypoints at the
End of the Route on page 5-29.
If the route has not been saved, the waypoint is erased.
If the route has been saved, the waypoint remains on the screen.
Reversing the Route
➤
ROUTE
REVERSE
ROUTE
To reverse the route, so you can Follow the route back:
1. Either press the ROUTE soft key followed by MORE,
or move the cursor over the required waypoint until the letters RTE are displayed.
The route soft keys are displayed.
2. Press the REVERSE ROUTE soft key. The current route is reversed on the
screen.
Editing a Route
Note: You can UNDO waypoints in the original route, not just the new ones.
5-30
hsb2 Plus Series Fishfinders
5.5 Following Routes and Going to Points
The default soft key GOTO accesses the functions to FOLLOW a route and GOTO
a waypoint or cursor. When you select the target destination, the chartplotter
calculates bearing, distance and cross track error; this information is passed to
a helmsman or autopilot. You can also restart the cross track error (XTE) from
the actual vessel position to set XTE to zero at that point.
ROUTE
GOTO
SCREEN
FIND SHIP
D4160-1
When the chartplotter is following a route, the target destination is indicated
by a square around the waypoint (or cursor marker) and a dotted line shows the
intended track, from your start point or previous waypoint, to the target
waypoint.
This section describes the following:
Following Routes
and Going to Points
• Follow a route either forwards, or in reverse order
• Target Point Arrival
• Other follow route options, including joining at a selected waypoint,
advancing waypoints, and restarting XTE
• Go to an individual point, either an existing waypoint or the cursor
• Stop and Restart Follow/Goto
An alarm is triggered when you approach a waypoint, this section describes
what happens when you arrive at waypoints. Chapter 6 describes how to set
the alarm.
The chartplotter can also display the vessel’s actual track and the track can be
recorded for later display. The Track function is described in the Section 5.7.
➤
GOTO
To access the Goto/Follow soft keys, press the default soft key GOTO (the soft
keys differ if a follow or goto is already in progress):
GOTO
WAYPOINT
GOTO
CURSOR
FOLLOW
ROUTE
D4171-1
Follow a Route
Note: The current route may have been created on this display, or created on
another unit and received on this display via SeaTalk.
If a route has been reversed or if a route on screen was being followed but
stopped before completion, the target waypoint – outlined by a square box –
may be different to when the route was created.
You should always check the target waypoint before initiating a follow route.
Chapter 5: Standard Chart Operations
➤
GOTO
5-31
To follow the current route:
1. Press the GOTO default soft key. The Goto/Follow soft keys are displayed.
2. Press the FOLLOW ROUTE soft key.
FOLLOW
ROUTE
Alternatively, to follow a route:
1. Place the cursor over a route leg until the letters RTE and the route soft keys
are displayed then press FOLLOW ROUTE.
RTE
FOLLOW
ROUTE
Your vessel’s current position becomes the origin, and the target waypoint in
the current route becomes the active target.
The soft keys change as follows:
STOP
FOLLOW
EDIT
ROUTE
CLEAR
ROUTE
REVERSE
ROUTE
➤
ROUTE
REVERSE
ROUTE
GOTO
To follow the current route in reverse:
1. Press the ROUTE default soft key, followed by MORE. The route soft keys
are displayed.
2. Press the REVERSE ROUTE soft key. The current route is reversed on the
screen. Press ENTER or CLEAR.
3. Press the GOTO default soft key. The Goto/Follow soft keys are displayed.
4. Press the FOLLOW ROUTE soft key.
FOLLOW
ROUTE
The soft keys change as follows:
STOP
FOLLOW
GOTO
CURSOR
RESTART
XTE
WAYPOINT
ADVANCE
D4172-1
These options are described in the following sections.
Alternatively:
RTE
REVERSE
ROUTE
1. Place the cursor over the route leg until the letters RTE and the route soft
keys are displayed. Press REVERSE ROUTE then FOLLOW ROUTE.
FOLLOW
ROUTE
Your vessel’s current position becomes the origin, and the target waypoint in
the current route becomes the active target.
Target Point Arrival
You can set up target alarms (see Section 6.3) to alert you when the vessel is
approaching the target point. The arrival alarm is defined as a circle (not
visible on the screen), with a specified radius around the target.
Target Point Arrival
D4251_1
These options are described in the following sections.
5-32
hsb2 Plus Series Fishfinders
The alarm is triggered when either of the following conditions is met:
• The distance to the target point is less than that specified for the arrival
alarm.
• Your vessel reaches the closest point of approach to the target (defined by a
line passing through the waypoint and perpendicular to the route leg).
➤
To cancel the arrival alarm and go towards the next waypoint in the route:
Press any key.
or
Wait for 10 seconds.
The target becomes the origin, the next waypoint becomes the target point, and
the two are connected by a dotted line indicating the current leg. Any previous
route leg is removed from the screen, but waypoints remain.
Other Follow Route
Options
Note: When following a route using a SeaTalk autopilot, the autopilot will not
turn to the new waypoint until it is accepted at the autopilot control unit.
Other Follow Route Options
You can use the soft keys to follow a route from a selected waypoint (join a
route), or if already following, you can advance to the next waypoint. You can
also restart the cross track error, setting the current vessel position as the new
origin.
In addition, you can move a selected waypoint as described in Section 5.3, or
remove a waypoint from the route as described in Section 5.4.
Joining a Route
➤
WPT
FOLLOW
FROM HERE
To start tracking the current route at a selected waypoint:
1. Move the cursor over the required waypoint until the letters WPT and the
waypoint soft keys are displayed.
2. Press the FOLLOW FROM HERE soft key.
Your vessel follows the route, using the selected waypoint as the target
point.
3. To return to the default display, move the cursor away from the waypoint or
press CLEAR or ENTER.
Chapter 5: Standard Chart Operations
5-33
Advancing to a Waypoint
➤
Once you are following a route, you can advance to the next waypoint, even if
you have not reached the current target waypoint:
1. If necessary, press the GOTO default soft key to display the Goto/Follow
soft keys.
GOTO
STOP
FOLLOW
GOTO
CURSOR
RESTART
XTE
WAYPOINT
ADVANCE
D4172-1
2. Press the WAYPOINT ADVANCE soft key. The current leg of the route is abandoned and the next waypoint becomes the target. The display is updated to
show the new route leg.
WAYPOINT
ADVANCE
While you are following a route, or going to a target point, you can restart the
XTE. This sets the XTE to zero and moves the origin to the actual vessel
position.
Restarting XTE is useful if you find yourself off track and want to go straight
to your target, rather than get back onto the original track.
➤
To restart XTE:
1. Press the GOTO default soft key, the Follow/Goto soft keys are displayed.
GOTO
2. Press the RESTART XTE soft key. The route origin moves to the current vessel
position, thus the XTE becomes zero.
RESTART
XTE
Going To an Individual Target Point
Rather than following a route, you can go directly to a selected target point,
this can be an existing waypoint (not in the current route), or the cursor
position.
➤
WPT
To navigate directly to an existing waypoint:
1. Use the trackpad to position the cursor over the required waypoint until the
letters WPT and the waypoint soft keys are displayed.
GOTO
WAYPOINT
EDIT
WAYPOINT
ERASE
WAYPOINT
MOVE
WAYPOINT
D4163-1
Alternatively, you can select the waypoint from the waypoint list as described
in Section 5.3.
Going To an
Individual Target
Point
Restart Cross Track Error (XTE)
5-34
hsb2 Plus Series Fishfinders
2. Press the GOTO WAYPOINT soft key.
Navigation to the selected waypoint begins. The soft key STOP GOTO is displayed.
GOTO
WAYPOINT
3. To return to the default soft key display, move the cursor away from the
waypoint or press ENTER or CLEAR.
➤
To navigate directly to the cursor position:
1. Use the trackpad to position the cursor as required.
2. Press the GOTO default soft key, followed by GOTO CURSOR.
If navigation is currently in progress you are warned “Already following
route. Cancel route and goto cursor?”.
GOTO
GOTO
CURSOR
To cancel the GOTO CURSOR operation, press NO.
To continue with the GOTO CURSOR operation (and stop the current GOTO
ROUTE), press YES.
Stop Follow or Stop
Goto
The chartplotter places a temporary waypoint as the target and starts to
navigate towards it. The waypoint is shown as a square with a circle and
dot in the center, and is connected to the vessel’s starting position with a
dashed line.
The soft key STOP GOTO is displayed.
STOP
GOTO
Note: The temporary waypoint is not added to the waypoint list; when the
GOTO is complete, or is stopped, the temporary waypoint is erased.
3. To return to the default soft key display, move the cursor away from the
waypoint or press ENTER or CLEAR.
Stop Follow or Stop Goto
➤
GOTO
STOP
GOTO
STOP
FOLLOW
To stop following the route or target point
either:
If necessary, press the GOTO soft key, then press the STOP GOTO/FOLLOW soft
key.
Or:
Move the cursor over any waypoint or leg in the current route, then press the
STOP GOTO/FOLLOW soft key.
The dotted line from your vessel to the target waypoint disappears.
Chapter 5: Standard Chart Operations
5-35
If you subsequently use the FOLLOW ROUTE soft key to restart navigation, the
route is followed from the point at which it was stopped. This is indicated by a
square around the target waypoint. If you want to follow from another
waypoint you can initiate the follow then use the WAYPOINT ADVANCE or
FOLLOW FROM HERE soft key to step through the route.
5.6 Transferring Waypoints and Routes
Displayed SeaTalk Waypoints
In an integrated system, when a route is made current on any SeaTalk
equipment it is sent to all SeaTalk instruments, including this chartplotter; this
route will override any other current route. When GOTO waypoint or GOTO
cursor is in operation it is considered a route.
Note: Transferred waypoints that are part of a route are not automatically
saved by the chartplotter, however you can save the route locally, thus adding
the waypoints to the local waypoint list.
Managing Database Lists
There are several methods of maintaining database lists. The method you
choose will depend on the links available (hsb2, SeaTalk or NMEA) and
whether you want to transfer individual waypoints or the complete waypoint
and route list:
• You can save the complete Waypoint and Route Lists to a user cartridge in
the chart card slot.
• You can load new Waypoint and Route Lists from a user cartridge in the
chart card slot.
• If waypoints are transmitted by other equipment on SeaTalk or NMEA,
you can receive them on the chartplotter.
When RECEIVE WPTS FROM ST/NMEA is selected, any waypoints sent on
SeaTalk or NMEA are transferred and appended, one-by-one, to the waypoint list; routes sent on NMEA are appended to the route list.
You can use this function to add waypoints from a PC connected via
NMEA.
• You can send the waypoint and route lists from the chartplotter to other
instruments via NMEA using the SEND WPT LIST function.
Sending the waypoint list does not affect current routes.
The NMEA link could be to a PC.
Transferring
Waypoints and
Routes
The current route can be edited on any instrument with route edit capability.
5-36
hsb2 Plus Series Fishfinders
• You can transfer the waypoint and route lists from one chartplotter to
another across an hsb2 link using SEND WPT LIST ON HSB and RECIEIVE WPTS
FROM HSB.
CAUTION:
The functions LOAD USER CARD, SEND WPT LIST ON HSB and RECIEIVE WPTS
FROM HSB replaces the existing waypoint and route lists with the
transferred lists.
➤ To save waypoints to, or load waypoints from a user cartridge:
CAUTION:
Loading waypoints from a user cartridge overwrites any existing
waypoint and route lists.
1. Insert a C-MAP User Card into the lower of the two cartridge slots.
MARKS
1. Press MARKS followed by the LOAD/SAVE USER CARD soft key.
2. The User Card Menu and associated soft keys are displayed.
Transferring
Waypoints and
Routes
3. Press the SAVE WPT/RTE DATA TO CARD or LOAD WPT/RTE DATA FROM CARD
soft key; an appropriate warning and Yes/No soft keys are displayed.
USER CARD MENU
USER CARD PRESENT
WARNING
SAVING DATA TO THE USER
CARD WILL ERASE ALL EXISTING
WAYPOINT AND ROUTE DATA
ON THE CARD.
ARE YOU SURE ?
YES
NO
D5594-1
4. Press Yes to continue or No to abandon the operation and return to the previous screen.
5. If the operation is successful, confirmation of the number of Routes and
Waypoints saved/loaded is displayed.
Chapter 5: Standard Chart Operations
5-37
USER CARD MENU
USER CARD PRESENT
SAVE COMPLETE
SAVED 2 ROUTE(S) AND
7 WAYPOINT(S)
CHECK
LOAD WPT/ SAVE WPT/
CARD IN
RTE DATA RTE DATA
FROM CARD TO CARD USER SLOT
D5595-1
If the operation fails, the Save Failed message is displayed.
USER CARD MENU
Transferring
Waypoints and
Routes
USER CARD NOT PRESENT
SAVE FAILED
NO OR INCORRECT CARD
ENSURE USER CARD IS CORRECTLY
INSERTED IN THE LOWER SLOT
CHECK
LOAD WPT/ SAVE WPT/
CARD IN
RTE DATA RTE DATA
FROM CARD TO CARD USER SLOT
D5596-1
➤
MARKS
WAYPOINT
LIST
WAYPOINT
TRANSFER
To receive incoming waypoints on SeaTalk or NMEA:
1. To display the waypoint list, press MARKS followed by the WAYPOINT LIST
soft key.
2. Press the WAYPOINT TRANSFER soft key.
3. Press the soft key RECEIVE WPTS FROM ST/NMEA.
The soft key changes to STOP RECEIVING WAYPOINTS.
When waypoints are transmitted by other equipment they are added to the
waypoint list on the chartplotter. Routes transmitted on NMEA are
appended to the route list.
4. To disable waypoint transfer, press the soft key STOP RECEIVING WAYPOINTS.
Alternatively, press ENTER, or CLEAR, twice to close the Waypoint List.
5-38
hsb2 Plus Series Fishfinders
➤
WAYPOINT
TRANSFER
To send the waypoint list on NMEA:
1. Display the waypoint list as previously described, then press the WAYPOINT TRANSFER soft key.
2. Press the soft key SEND WPT LIST ON NMEA.
The soft key changes to STOP SENDING WAYPOINTS.
The waypoint and route lists are transmitted from the chartplotter to other
instruments on NMEA.
➤ To receive the waypoint and route lists via hsb2, you must set-up the transfer on
both display units - one unit will send waypoints, the other will receive them.
CAUTION:
Receiving waypoints from another hsb2 instrument overwrites any
existing waypoint and route lists.
WAYPOINT
TRANSFER
1. Display the waypoint list as previously described, then press the WAYPOINT TRANSFER soft key.
Transferring
Waypoints and
Routes
2. Press the soft key SEND WPT LIST ON HSB or RECIEIVE WPTS FROM HSB; you
are prompted to confirm.
Press NO to cancel the operation, then ENTER if you wish to remove the
route list.
Press YES to continue. The waypoint list is transmitted to/from the chartplotter from/to another instrument on hsb2. While the data is being transferred the soft key changes to STOP SENDING WAYPOINTS; when the
transfer is complete the soft key is re-displayed.
Chapter 5: Standard Chart Operations
5-39
5.7 Using Tracks
The Track function is used to mark on-screen the trail that your vessel has
followed, as if it had left a visible fixed wake.
While the track is turned on, it is recorded in the display unit’s memory. You
specify the interval at which track points are made, a line is drawn on-screen
between each point. A maximum of 750 track points each can be saved in the
current track and in up to 5 saved tracks, for a total of up to 4500 points. The
current track remains on-screen, even following a power off/on, until you
clear the track.
Breaks in the track will be caused when any of the following occur for longer
than the specified track interval: the track is switched off then on; the position
fix is lost; the display unit is switched off.
To enable you to follow this track on your return voyage, the SmartRoute
function converts the track (or the last segment of a track with breaks) into a
route which is automatically reversed, see SmartRoute on page 5-42.
This section describes:
• Setting up a track, including how to specify the interval.
• Clearing the current track.
• Managing tracks, using the track list, including Saving, Naming, Erasing
and Showing a track.
• Using Smart Route.
➤
To access the track controls:
1. From the chart display, press the MENU key to display the chart set up soft
keys.
SYSTEM
SET UP!
CHART
SET UP!
TRACK
SET UP!
GPS
SETUP!
D4162-1
2. Press the TRACK SETUP soft key to display the Track soft keys:
TRACKS
OFF ON
CLEAR
TRACK
TRACK
LIST
TRACK
INTERVAL
D4179-1
The following instructions assume you have the track soft keys displayed.
Using Tracks
A track can be saved and retrieved for display at a later date. For example, you
may wish to display a previous track, and then place waypoints along it that
you can follow. You can only display one track at a time; you must clear a
current track from the screen if you want to display a saved track.
5-40
hsb2 Plus Series Fishfinders
Setting Up a Track
You use the track soft keys to switch the track on and to specify the interval at
which track points are saved. The interval default is a distance of 0.1nm. The
maximum track length is 500 points, when the track has reached this length,
the first points are overwritten. The track is saved until you switch it off.
➤
To set up a track:
1. Press the TRACK INTERVAL soft key.
Press the appropriate soft key to set either a time interval or a distance interval; press the UP arrow to increase the interval, the DOWN arrow to decrease
the interval.
Press ENTER to return to the track soft keys.
TRACK
INTERVAL
TIME
1S
DISTANCE
0.1nm
Setting Up a Track
D4258-1
2. Press the TRACK OFF ON soft key to toggle tracks on.
TRACK
OFF ON
Your vessels trail will be displayed on-screen, with a line joining the
points at the selected interval.
Clearing the Current Track
You can clear the current track from the screen. When you select CLEAR
TRACK, if the current track has not been saved, you have the option of saving it.
➤
CLEAR
TRACK
SAVE
TRACK
To clear the current track:
1. Press the CLEAR TRACK soft key.
2. If the track has not been saved the SAVE TRACK soft keys are displayed.
To clear the track without saving it in the Track List, press NO.
To save the track in the list, press YES. The Name track soft keys are displayed and you should continue as described in the following section, Saving and Naming a Track.
Press CLEAR to abort the Clear Track operation.
The current track is cleared from the screen and the default soft keys are
displayed.
Managing Tracks
Although it is easy to set up a track, and this track is retained even if you switch
off your display, you can store a number of different tracks so that you can
review them at a later date. This section explains how to:
• Save and name a track.
• Name, Erase and Show an existing track.
Chapter 5: Standard Chart Operations
5-41
Saving and Naming a Track
You can save up to 5 named tracks in the Track List. These tracks can be redisplayed at a later date.
➤
To save and name the current track:
1. Press the TRACK LIST soft key. The track list pop-up and associated soft keys
are displayed.
TRACK
LIST
2. The next available entry on the track list is highlighted.
(If required, you can use the trackpad to select another position in the list;
this can be a blank slot, or an existing track that you no longer require).
SAVE
TRACK
3. Press SAVE TRACK. The name track soft keys are displayed.
NAME TRACK?
NO
D4256-1
4. If you do not wish to name or rename the track, press the NO soft key (or
CLEAR) to clear the list. The track is saved and is listed as Track Not
Named.
5. If you wish to name the route press the YES soft key:
Use the trackpad to move the cursor right or left to the character you wish
to edit. Then use the top or bottom of the trackpad to increase or decrease
the letter or number.
or
Use the arrow keys and alphanumeric keys on the ST80 Navigator keypad
to input or edit the characters, as described in Using the ST60 or ST80
Navigator Keypad on page 5-16.
6. Press ENTER to finish and clear the Track List, then to return to the default
soft key display, press ENTER again or CLEAR.
Naming, Erasing and Showing a Track
➤
TRACK
LIST
NAME
TRACK
To name an existing track, erase a track or show a track, you select the track
from the track list, then press the appropriate soft key as follows:
1. Press the TRACK LIST soft key. The Track List is displayed. The grey selection bar indicates the selected track.
Select the required track then press the appropriate soft key.
2. If you NAME a track:
Managing Tracks
YES
5-42
hsb2 Plus Series Fishfinders
Use the trackpad to move the cursor right or left to the character you wish
to edit. Then use the top or bottom of the trackpad to edit the character.
or
Use the arrow keys and alphanumeric keys on the ST80 Navigator keypad
to input or edit the characters, as described in Using the ST60 or ST80
Navigator Keypad on page 5-16.
Press ENTER finish the operation or CLEAR to cancel the name, then
ENTER to remove the track list.
3. If you ERASE a track you are prompted to confirm.
Press NO to cancel the operation, then ENTER if you wish to remove the
track list.
Press YES to erase the track from the list, then ENTER to remove the track
list.
ERASE
TRACK
4. If you SHOW a track, and you have a current track on screen, you are
prompted to save the track. Proceed as previously described in Clearing the
Current Track.
Alternatively, press the NO soft key to cancel the SHOW TRACK operation.
The track list is removed and the selected track is displayed.
SHOW
TRACK
SmartRoute
5. Press ENTER or CLEAR to return to the default display.
SmartRoute
SmartRoute enables the current track, or the last segment of a track with
breaks, to be converted to a route (the track could have been retrieved from the
track list). SmartRoute places a waypoint at the last track point, then considers
each point in turn and determines the closest route through the recorded track.
The number of waypoints created is minimized, while maintaining optimum
correlation to the recorded track. On completion, the maximum deviation of
the route from the recorded track is displayed.
➤
To convert the current track into a route:
1. Select MAKE INTO ROUTE and press ENTER.
The current track is converted to a new route and becomes the current
route, with the most recently placed track point as the start of the route, i.e.
the track is reversed.
If there is an unsaved current route on screen, the option to save the route is
given, see Section 5.4, Working with Routes.
2. Check the calculated route and, in particular, that the route deviation from
the original, given in the warning box, is within navigable limits.
CAUTION:
Before following the route, ensure that it is safe for navigation, noting that
it may deviate from your actual path travelled.
Chapter 5: Standard Chart Operations
5-43
5.8 Typical Chart Scenarios
The following illustrations provide operating guidelines for typical navigation
scenarios. These scenarios can be used as a training guide; they show you how
to perform a particular operation and they introduce many of the chartplotter
functions.
Each scenario indicates the key presses required to perform particular tasks. A
typical chartplotter screen image is shown for each task.
The scenarios assume you have read the previous sections of this chapter and
that you are familiar with the Operating Controls.
Operating guidelines are provided for the following scenarios:
• Make and Follow a Routes
Create a Route
Follow a Route
• Review the Passage Plan
View Route Information
Change the SOG, Hours and ETA.
Typical Chart
Scenarios
• Working with Waypoints
Place a Waypoint
Goto a Waypoint
5-44
hsb2 Plus Series Fishfinders
Place and Goto a Waypoint
1
1. Press MARKS
2. Position Cursor as required
Place and Goto a
Waypoint
2
Press the soft key
3
Press the soft key to go to the
waypoint selected by the cursor.
D4267-1
Chapter 5: Standard Chart Operations
5-45
4
The vessel navigates towards the target
waypoint
See Sections:
5.3 Working wth Waypoints
5.5 Following Routes and Going to
Points
Place and Goto a
Waypoint
D4267-2c
5-46
hsb2 Plus Series Fishfinders
Make and Follow a Route
1
ROUTE
GOTO
SCREEN
FIND SHIP
Press the soft key
2
MAKE
ROUTE
EDIT
ROUTE
CLEAR
ROUTE
MORE!
Press the soft key
Make and Follow a
Route
3
1. Position Cursor - in this example
over an existing waypoint
2. Press the soft key
4
Position Cursor for next waypoint,
then press soft key.
Repeat to plot all waypoints in
sequence.
D4268-1
Chapter 5: Standard Chart Operations
5-47
Press the soft key. The route becomes
the current route.
ROUTE
GOTO
SCREEN
Make and Follow a
Route
FIND SHIP
Press the soft key
GOTO
CURSOR
GOTO
WAYPOINT
FOLLOW
ROUTE
Press the soft key
The vessel starts to navigate to the
first (target) waypoint in the route.
STOP
FOLLOW
GOTO
CURSOR
RESTART
XTE
WAYPOINT
ADVANCE
5.4 Working with Routes
5.5 Following Routes and Going to
Points
D4268-2c
5-48
hsb2 Plus Series Fishfinders
Review Your Passage Plan
1
ROUTE
GOTO
SCREEN
FIND SHIP
Press the soft key
MAKE
ROUTE
EDIT
ROUTE
CLEAR
ROUTE
2
MORE!
Press the soft key
REVERSE
ROUTE
SAVE
ROUTE
ROUTE
LIST
3
MORE!
Press the soft key
Review Your
Passage Plan
4
1. Use the trackpad to move
selection bar over required route.
2. Press the soft key
5
Time defaults to ETA - and assumes
the current time is the start time.
D4269-1
Chapter 5: Standard Chart Operations
5-49
6
See Section:
5.4 Working with Routes
Change the TIME to HOURS - the display
indicates it will take 32 minutes to reach
the destination. You can change the
PLANNED SOG; the display updates to
indicate TIME required at the planned
speed.
Review Your
Passage Plan
D4269-2c
5-50
hsb2 Plus Series Fishfinders
Review Your
Passage Plan
Chapter 6: Further Chart Operations
6-1
Chapter 6: Further Chart Operations
6.1 Introduction
This chapter explains how to use the additional functions that are provided
with the L755RC Plus, L760RC Plus, and L1250RC Plus Combined
Fishfinder/Chartplotter Displays. Chart functions are also available on L1250
Plus and L760 Plus fishfinder-only units, when connected to an hsb2 Plus
Series device with chartplotter functionality (see Section 2.7, Integrated
Systems).
This chapter covers the following topics:
• Measuring distances and bearings on the chart, using the VRM/EBL key
• Setting alarms and timers
• Man Overboard (MOB)
Introduction
• Cursor Echo
• Radar Overlay
• GPS Setup
• Data Log Mode
In order to use some of these functions, you may need the following additional
data from equipment connected to your system via a SeaTalk, hsb2, or NMEA
link:
Table 6-1:
Function of External Data
Data
Example source
Integrated functions available
Heading
COG
Compass*
GPS
- North Up or Course Up heading modes
- MOB (if speed data also available)
Radar data
Radar system (via
hsb2
- Radar data, either full-screen or in a half-screen window
Position
GPS system
- Waypoints
- Position, COG, SOG and time data in Data Box and Nav
Window
- MOB
- Data Log
Other data
Transducers
- Data Box and Nav Window data displays, including speed,
depth, wind, temperature
*If heading data is available via both NMEA and SeaTalk, NMEA data takes priority. For all other data,
SeaTalk data takes priority (see Section 6.3).
6-2
hsb2 Plus Series Fishfinders
6.2 Measuring Distances Using the VRM/EBL Key
You can obtain an accurate measurement of the distance and bearing between
two points by using the VRM/EBL key.
➤
To place a ruler line and Ruler data box:
1. Position the cursor on the starting point from which you wish to measure.
VRM/EBL
2. Press VRM/EBL.
A Ruler data box is displayed showing the bearing and distance from the
starting point to the cursor position. The character A appears at the cursor
location.
3. Use the trackpad to move the cursor to the measurement end point. A line
connects the cursor to the starting point, and the Ruler data box is updated
to show the bearing and length of the line as shown in Figure 6-1.
Measuring
Distances Using the
VRM/EBL Key
4. Press ENTER to fix the end point of the ruler line, and return to normal cursor control. The letter B marks the location of the end point on the chart.
Figure 6-1:
Measuring Distance Using a VRM
Chapter 6: Further Chart Operations
➤
6-3
To re-position one end of the ruler line:
1. Move the cursor over the ruler line towards the end that you want to reposition, until the letters A→ B are displayed.
2. Press ENTER to take cursor control of the ruler. The ruler end moves to the
cursor which changes to a four-headed arrow.
3. Move the cursor to the required position. The ruler data box is updated.
➤
To clear the ruler line and ruler data box
either:
Move the cursor over the ruler line, until the letters A→ B are displayed, then
press CLEAR.
or:
Press VRM/EBL, the ruler soft keys are displayed. Press RULER OFF ON to
toggle the ruler line and data box off.
➤
To clear the ruler data box:
Press VRM/EBL, the ruler soft keys are displayed. Press RULER DATABOX OFF
ON to toggle the ruler data box off.
➤
To move the Ruler data box, using the context-sensitive cursor:
VRM/EBL
RULER
OFF ON
RULER
DATABOX
OFF ON
BOX
1. Move the cursor over the box until the letters BOX are displayed, and press
ENTER to take cursor control of the box.
2. Use the trackpad to move the box to its new location, and press ENTER to
drop it and return to normal cursor operation.
Measuring
Distances Using the
VRM/EBL Key
4. Press ENTER again to set the position and return to normal cursor control.
Alternatively, press CLEAR to reset the ruler to the previous position.
6-4
hsb2 Plus Series Fishfinders
6.3 Alarms and Timers
Alarm Reporting
The chartplotter reports the following alarms, that are set using the ALARMS
key:
ALARMS
Alarms and Timers
Alarm
Indicates:
Arrival
Your vessel has arrived at the active waypoint: it has either
reached the arrival circle (the radius of which is specified) or,
has reached its closest point of approach (defined by a line
passing through the waypoint and perpendicular to the route
leg).
Off Track
Your vessel has exceeded the specified distance (maximum
cross track error) from the active route leg.
Anchor
Your vessel has drifted from its anchor position (set when the
alarm was turned on) by more than the specified distance.
Grounding
The chartplotter checks a sector ahead of your vessel for a
dangerous object (land, depth area, intertidal area, rock,
obstruction or shore obstruction). You specify the depth and
range of the sector from your vessel.
You can view a report of the objects that triggered the alarm.
Countdown
The countdown timer has reached zero.
Alarm Clock
The time matches the specified alarm time.
The alarms are switched on or off, and the limits set, using the Alarms Set Up
menu, accessed from the ALARMS key.
When an alarm is triggered, the alarm buzzer sounds and a pop-up window
describing the alarm is displayed.
➤
To silence the alarm and clear the message, press any key.
If the alarm was generated by the chartplotter, the appropriate action is taken.
For example, following an arrival alarm, the next route leg is activated.
If an anchor alarm is silenced, but the alarm condition persists, the alarm is
repeated every 30 seconds.
External Alarms
All SeaTalk system alarms (except autopilot alarms) are received and
displayed on the chartplotter. You can silence these alarms by pressing any
key. No other action is taken by the chartplotter except to silence the alarm.
Chapter 6: Further Chart Operations
6-5
Setting Alarms and Timers
➤
ALARMS
To set up an alarm or timer:
1. Press the ALARMS key. The Alarms Set Up menu is displayed, showing
the current settings (see Figure 6-2).
2. Use the trackpad to move the selection bar up or down the options. As each
line is highlighted, the soft key labels are updated to show the current settings and controls.
ALARMS SET UP
ARRIVAL ALARM
0.01nm
OFF TRACK ALARM
ON
ANCHOR ALARM
OFF
GROUNDING ALARM
5M/1.0nm
COUNTDOWN TIMER
00:33:00
ALARM CLOCK
OFF
Setting Alarms and
Timers
ALARMS
SELECT ARRIVAL
ALARM RADIUS
D4265-4
Figure 6-2:
Alarms Set Up List
3. Use the up or down soft keys to change the alarm setting. For example, for
the arrival alarm you can adjust the radius from the waypoint at which the
arrival alarm will be triggered.
The arrival, off track and anchor alarm distances can be set in the range
0.01 to 9.99 nm, in steps of 0.01nm.
The grounding alarm depth can be set from 1 to 20m in 1m steps and can be
specified to cover a sector at a range from 0 to 1nm, in 0.1nm steps.
The timer is set in hours, minutes and seconds, and the alarm clock in hours
and minutes.
ALARM
OFF ON
4. If required, press the ALARM OFF ON soft key to toggle the alarm on or off.
If you turn an alarm off, its value is retained and will be used when you turn
the alarm on again.
Note: You can turn all the alarms and timers on and off, except for the Arrival
Alarm which is always on.
5. Press ENTER to save the changes and clear the list.
6-6
hsb2 Plus Series Fishfinders
6.4 Man Overboard (MOB)
If you lose a person or object overboard, and need to return to the location, you
should use the Man Overboard (MOB) function.
You can select the type of data used for the MOB position using the set up
menus (see Section 7.3).
Note: To obtain MOB position, you need either of the following:
• Position data from a GPS or equivalent device
• Heading and speed data, so that the position can be calculated by dead
reckoning
➤
MARKS
To initiate the MOB procedure, press and hold the MARKS key for two
seconds. The system then performs the following tasks automatically:
• Redraws the chart at 1/2 nm (even if cartography is not available but plotter
mode is on).
Man Overboard
(MOB)
• Marks the current position with a MOB symbol
current active waypoint and route.
which replaces any
• Displays the MOB data box, showing the bearing and distance from your
vessel to the MOB waypoint position, and the elapsed time since the MOB
was initiated (Figure 6-3).
• Displays the position data box, showing your vessel’s position.
• As your vessel moves from the MOB position, a dotted line is displayed
connecting the MOB symbol and the vessel’s current position.
• Sounds a 4-second alarm pattern every 30 seconds.
• Sends an MOB message (including bearing and distance) to other units in
the system, via the SeaTalk connection.
MOB position
MOB
0.33nm
BRG 162°T
00:05:24
RNG
POSITION
N 49°54^76
W 002°09^83
D4273-3
MOB data box
Figure 6-3: MOB Display
Chapter 6: Further Chart Operations
➤
MARKS
6-7
To cancel the MOB, press and hold the MARKS key for 2 seconds.
The chart is re-drawn at its previous scale, and the MOB symbol and data box
are removed.
Note: The MOB procedure can also be initiated or cancelled if the appropriate SeaTalk message is received by the display unit.
6.5 Cursor Echo
In a system with a radar display connected via SeaTalk, you can set the display
to enable cursor echo. Cursor echo (accessed from System Set Up, described
in Section 7.3) enables you to display a radar cursor on the chart picture, or a
chart cursor on the radar picture (you cannot display a remote chart cursor in a
chart window nor a remote radar cursor in a radar window).
• Radar Cursor In: displays the cursor from another radar on the chart display or chart window (default - OFF).
• Chart Cursor In: displays the cursor from another or chartplotter on the
radar display or radar window (default - OFF).
Note: The remote display must have SeaTalk Cursor Out enabled.
• SeaTalk Cursor Out: enables the output, onto SeaTalk, of the display’s
own cursor (default - OFF).
• Cursor Echo Local: echoes the cursor position between open windows on
the same display (default - ON).
If you set the options to OFF, no cursor echo information is displayed.
When the appropriate option is switched on, the display shows its own cursor,
plus the cursor of the other display with appropriate cursor text (RDR or CHT) to
indicate its origin. This means that you could move the cursor over a target on
the radar display, and check the identity of the target by looking at the radar
cursor position on the chartplotter.
6.6 Radar Overlay
If radar data is available from another display connected on hsb2, the radar
targets can be overlaid onto the full-screen chartplotter display. The radar/
chart overlay option helps you to distinguish between fixed, charted objects
and other objects that could be moving vessels. Some radar controls are
available in overlay mode.
The following criteria must be true for radar/chart overlay to function
correctly:
Cursor Echo
The following options can be toggled ON or OFF:
6-8
hsb2 Plus Series Fishfinders
• Position and heading data are provided so that vessel position and orientation can be determined.
• The vessel must be displayed on screen.
• The chartplotter must be in North Up or Course Up mode (see Section 7.5).
• The chartplotter range must be between 1/4nm and 48nm (equivalent to a
radar range of 1/8nm to 24nm).
• Custom range scales are disabled on the radar.
• The radar must be transmitting.
To ensure the vessel remains on the screen, you could use Find Ship (see Using
FIND SHIP on page 3-29) to home the cursor onto the vessel.
When Radar/Chart overlay is switched on, the status bar indicates OVL. If the
option is switched on but the overlay is not visible (because one of the above
criteria has failed), the status bar indication changes to (OVL).
Radar Overlay
When Radar/Chart overlay is switched on the soft key MORE... provides
access to the SCREEN soft key and to the radar controls TARGETS and MARPA.
The radar GAIN control is also active in overlay mode.
Radar/Chart overlay is displayed at the current chart range. You should be
aware that if radar is shown on any other display, its range will match that
displayed on Radar/Chart overlay. Conversely, if you change the radar range
on any display, the Radar/Chart overlay image will change to the new radar
range.
➤
To select radar/chart overlay:
1. Press the DISPLAY key to show the DISPLAY pop-up, then if necessary
press again to select Chart mode.
2. Press the OVERLAY OFF ON soft key to toggle the option on.
The two highest intensity radar returns are displayed in purple, over the chart
image. The radar image is translucent, so that chart text, contours and outlines
are visible beneath the radar targets.
Chapter 6: Further Chart Operations
6-9
6.7 GPS Setup
GPS set up page provides you with information and the status of the tracked
navigation satellites for a SeaTalk GPS. It also enables you to SET UP a SeaTalk
Differential GPS, by manually retuning it to a different differential beacon.
Note: The satellite information is not available when you use an NMEA GPS.
➤
To select GPS Set Up:
1. Press MENU, then press the GPS SETUP... soft key.
The Navigation Status pop-up window shown in Figure 6-4. This window
provides, for each tracked satellite, the satellite number, its signal strength,
azimuth angle and elevation angle from your vessel.
MENU
GPS
SETUP!
NAVIGATION STATUS
RESTART
GPS
SIGNAL
STATUS
IN USE
IN USE
IN USE
IN USE
IN USE
IN USE
IN USE
SPARE
SPARE
SPARE
AZ
085
292
127
075
174
290
056
321
024
237
HDOP
FIX STATUS
1
FIX
ELEV
085
051
048
043
028
014
012
011
005
065
GPS Setup
SAT
03
31
21
23
22
19
17
27
16
15
D-GPS
SETUP!
D4281-2
Figure 6-4:
➤
GPS
SETUP!
Navigation Status Window
To tune a differential SeaTalk GPS to another beacon:
1. Press D-GPS SETUP, the Differential GPS Setup pop-up is displayed with
MODE and BEACON SELECT soft keys.
2. Press MODE AUTO MAN to toggle the GPS to manual tuning.
3. Press BEACON SELECT, use the soft keys to set the required beacon frequency and bit rate.
The status of the selected beacon is displayed in the pop-up.
Press ENTER to select the beacon and return to the Navigation Status window, then ENTER to return to the MENU soft keys.
6-10
hsb2 Plus Series Fishfinders
Note: Under normal circumstances RESTART GPS is not required.
6.8 Data Log Mode
You can set the chartplotter to log course data every thirty minutes. Up to 48
log entries are held, when 48 entries have been made, the chartplotter will start
overwriting the first entries.
You start the log using soft keys provided in Data Log Mode. When you select
Data Log Mode the log is displayed full-screen. If the screen is full, you use the
trackpad to scroll the list and view further log entries. Each line in the log
shows:
• Time of log entry
• Position at time of log entry
• Course Made Good (CMG) since last log entry
• Distance Made Good (DMG) since last log entry
Data Log Mode
Once you have enabled the data log, data is continually logged, but you must
set the display to Data Log Mode to view it. You use the DISPLAY key to
change the full-screen mode.
You can stop the log at any time and you can clear the log from memory.
➤
To activate Data Log Mode:
1. Press DISPLAY, the DISPLAY pop-up is shown.
DISPLAY
2. Press DISPLAY again, until LOG is selected, then press ENTER.
➤
START LOG
To start recording log entries, press the START LOG soft key.
As shown in Figure 6-5, the chartplotter records the time and vessels position.
Every thirty minutes the time, new position, distance made good and course
made good are recorded.
The START LOG soft key changes to STOP LOG.
Chapter 6: Further Chart Operations
TIME
15:30
16:00
16:30
17:00
17:30
18:00
18:30
19:00
POSITION
50°21^890N
001°20^610W
50°18^010N
001°20^070W
50°21^850N
001°19^290W
50°18^500N
001°21^300W
50°20^990N
001°18^280W
50°19^660N
001°21^960W
50°19^730N
001°18^030W
50°20^930N
001°21^750W
50°18^550N
001°18^650W
CMG
DMG
346°M
6.86KM
180°M
7.23KM
012°M
7.23KM
206°M
6.67KM
043°M
5.74KM
245°M
5.00KM
093°M
4.63KM
302°M
5.00KM
145°M
5.74KM
Data Log Mode
19:30
6-11
STOP LOG
CLEAR LOG
D4284-1
Figure 6-5:
➤
➤
To clear the log entries:
Press the CLEAR LOG soft key, you are prompted “Are You Sure”. To cancel the
CLEAR LOG operation press the NO soft key.
To continue press the YES soft key, all log entries are deleted, but the data log
remains active.
CLEAR LOG
➤
STOP LOG
To stop recording log entries:
Press the STOP LOG soft key.
STOP LOG
DISPLAY
Data Log Window
To return to the chart display,:
Press DISPLAY to select the chart mode, then press ENTER.
The log continues until you return to the data log mode and press STOP LOG.
6-12
hsb2 Plus Series Fishfinders
Data Log Mode
Chapter 7: Setting Up the System Defaults
7-1
7.1 Introduction
Once you have installed your display unit and are familiar with its basic
operation (described in Chapter 1 and Chapter 3), you need to set it up so that
it obtains the correct information from the equipment you have connected it to,
operates according to your requirements, and displays information according
to your preferences.
MENU
This is achieved using the soft key controls that are displayed when you press
the MENU key.
In most cases, you will only need to use the MENU key options when you first
set up your system. However, you may decide to change the way you have
customized some aspects, such as the screen and help setting, as you become
more familiar with your system.
Once you have set the values, they remain as the default settings until you reset
them; they are retained even if you power off your display.
This chapter covers the following topics:
• Changing the default set up parameters
• System parameter functions and default settings
• Fishfinder specific parameter functions and default settings
• Chart specific parameter functions and default settings
You should check the functions of the parameters, and decide on the new
settings, before making the changes.
Note: The SYSTEM SET UP menu option from the chartplotter display is the
same as that accessed from the fishfinder display SYSTEM SET UP menu.
Introduction
Chapter 7: Setting Up the System Defaults
7-2
hsb2 Plus Series Fishfinders
Changing the Set
Up Parameters
7.2 Changing the Set Up Parameters
The set up parameters are divided into three sections:
• System, to control the aspects of the system that are not specific to the fishfinder or chart.
• Fishfinder, to control the fishfinder display preferences, including HSB
mode, calibration and simulator.
• Chart, to control the chartplotter display (in fishfinders with the Raychart
feature), including waypoint information, vectors and radar/chart synchronization.
Note: The GPS menu is described in Chapter 6 and the Track Set Up menu is
described in Chapter 5.
This section provides instructions for displaying and changing the default
values. The following sections list the parameters and their possible settings,
and describe the function of each parameter in turn.
➤
MENU
To set the default parameters:
1. Press the MENU key to display the set up soft keys. The options available
depend on the selected operating mode.
Fishfinder
SYSTEM
SET UP¬
SONAR
SET UP¬
SCROLL
SPEED
TRIP
RESET
D5019-1
Chart
SYSTEM
SET UP!
CHART
SET UP!
TRACK
SET UP!
GPS
SETUP!
D4162-1
2. Press the soft key for the set up you require.
The requested set up menu is displayed, listing the parameters and their
current settings.
3. Use the trackpad to move the selection bar up and down the list. An arrow
is displayed at the top or bottom right-hand corner if you can scroll the list
to display further parameters.
As each line is highlighted, the soft keys are updated to show the settings
available.
• For parameters that have a numeric value, or more than four possible
settings, a scroll list is displayed above two of the soft keys.
7-3
• Some parameters are controlled by a slider that is displayed above two
of the soft keys.
• For some parameters, a soft key provides access to a sub-menu of further options.
4. Press the soft key corresponding to the desired setting or, for scroll lists, use
the soft keys to scroll forwards or backwards through the list until the
required setting is displayed. This setting is retained when you move the
selection bar on to the next parameter in the menu list.
For sliders, press the appropriate soft key repeatedly to increase or
decrease the slider value in individual steps, or press and hold the key to
change the setting quickly.
5. Once you have reset all the required values, press ENTER to clear the menu
and return to the set up soft keys.
6. Press ENTER, MENU or CLEAR to clear the soft keys and return to the
default display.
You can return all the settings to their original factory settings, if required, by
performing a factory reset as described in Chapter 8.
Changing the Set
Up Parameters
Chapter 7: Setting Up the System Defaults
7-4
hsb2 Plus Series Fishfinders
System Set Up
Parameters
7.3 System Set Up Parameters
The following table lists the System menus and their options, shows the
factory default setting, and provides a space for you to make a note of your
new default setting. Each parameter is described in the following subsections.
Table 7-1:
System Set Up Parameters
Menu
Options
Factory
Default
DATA BOXES
POSITION
SPEED
DEPTH
COG
SOG
TIME
DATE
WIND
WAYPOINT
CROSS TRACK ERROR
HEADING
LOG/TRIP
PILOT
VMG
TEMPERATURE
TIDE SET/DRIFT
OFF, LAT/LONG, or TDs
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF, APPARENT, TRUE, BOTH
OFF, LAT/LON, RNG/BRG/TTG
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF, WIND, WPT, or BOTH
OFF or ON
OFF or ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
BEARING MODE
MAGNETIC or TRUE
TRUE
CURSOR REFERENCE
MAG/TRUE or RELATIVE
RELATIVE
CURSOR READOUT
OFF, LAT/LONG, RNG/BRG, or
BOTH
RNG/BRG
DAY/NIGHT (L755RC only)
DAY/NIGHT
DAY
HELP
OFF or ON
ON
SOFT KEYS
OFF or ON
ON
KEY BEEP
OFF or ON
ON
MOB DATA
DR or POSITION
DR
PILOT POP-UP
OFF or ON
OFF
MENU TIMEOUT PERIOD
NO TIMEOUT, 10, 20, or
30 SECONDS
NO TIMEOUT
DISTANCE UNITS
NAUTICAL MILES, STATUTE
MILES, KILOMETERS, or
KILOYARDS
NAUTICAL MILES
SPEED UNITS
KNOTS, MILES PER HOUR, or
KILOMETERS PER HOUR
KNOTS
New
Default
Chapter 7: Setting Up the System Defaults
System Set Up Parameters
Menu
Options
Factory
Default
DEPTH UNITS
METERS, FEET, or FATHOMS
FEET
TEMPERATURE UNITS
CENTIGRADE or FAHRENHEIT
FAHRENHEIT
VARIATION SOURCE
AUTOMATIC or MANUAL
AUTO
BRIDGE NMEA HEADING
OFF or ON
OFF
NMEA-OUT SET UP
APB
BWC
BWR
DBT
DPT
MTW
RMB
RSD
RTE
TTM
VHW
VLW
WPL
GGA
GLL
RMA
RMC
VTG
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
CURSOR ECHO
RADAR CURSOR IN
CHART CURSOR IN
SEATALK CURSOR OUT
CURSOR ECHO LOCAL
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF
OFF
OFF
ON
DATE FORMAT
DD/MM/YY or MM/DD/YY
MM/DD/YY
TIME FORMAT
12 HOUR or 24 HOUR
12 HOUR
TIME OFFSET
UTC, or local offset value:
Plus or minus up to 12 hours,
in whole hours
UTC
GPS SOG/COG FILTER
HIGH, MEDIUM, or LOW
COMPASS SETUP
LINEARISE COMPASS or
ALIGN HEADING
New
Default
System Set Up
Parameters
Table 7-1:
7-5
7-6
hsb2 Plus Series Fishfinders
Table 7-1:
System Set Up Parameters
Data Boxes
Menu
Options
Factory
Default
LANGUAGE
ENGLISH (UK), ENGLISH (US),
DANISH, FRENCH, GERMAN,
DUTCH, ICELANDIC, ITALIAN,
NORWEGIAN, PORTUGUESE,
SPANISH, SWEDISH, or FINNISH
ENGLISH (US)
SIMULATOR
OFF, DATA, RADAR, or BOTH
OFF
New
Default
Data Boxes
Press the SELECT BOXES soft key to display the data box sub-menu. This allows
you to select up to 6 data boxes that you can display on the fishfinder.
Note:
1. A fixed set of sixteen (nine in the L755RC Plus) of these data items are
available for display in the Nav Data half-screen window (see Chapter 3).
2. In addition to these grouped data boxes, boxes for the cursor readout,
VRM/EBL data, waypoint data, MOB data and simulator status are displayed when selected or when the appropriate function is active.
3. Radar data is only repeated if the display is connected to an hsb2 Plus
Series radar master display.
Data boxes provide regularly used data in a compact form so that most of the
picture can still be seen. The ones you select here can be turned on and off as a
group during normal operation, and you can also move them around the screen
individually using the context-sensitive cursor (see Context-Sensitive Cursor
Control on page 1-18).
Bearing Mode
The mode (magnetic or true) of all the bearing and heading data displayed.
This is indicated in the radar status bar after the heading value, if displayed.
Cursor Reference
The mode of the bearing data displayed for the cursor readout. The bearing
information can be displayed in either of two forms:
• Relative: The bearing relative to your vessel’s heading.
• Mag/True: The actual bearing in either degrees magnetic or degrees true.
This option is only available in Radar mode if your system includes a radar
display and you have heading data from a compass.
7-7
If you choose this mode, the selection you made for the previous parameter (Bearing Mode), °M or °T, is displayed in the cursor (Rng/Brg) data
boxes. The current units are shown for the heading value in the status bar
at the top of the screen.
Cursor Readout
This option controls whether the cursor data is shown in latitude and longitude
or in range and bearing. Alternatively, you can show both types of readout, in
separate boxes, or turn the cursor data box off.
You can also turn the cursor readout box(es) on and off during normal
operation, via the SCREEN default soft key (see Switching the Cursor Data Box
On and Off on page 3-26).
Day/Night (Monochrome Display only)
This option allows you to change the target presentation between day and
night modes.
In the normal day presentation, black targets are displayed on a white
background. If you select NIGHT presentation, the picture is reversed, so that
white targets are shown on a black background to reduce the intensity of the
image.
Help
When Help is set to ON, a prompt appears when selecting a soft key or menu
choice, and when using the context-sensitive cursor. The help message is
cleared when an action is selected.
Soft Keys
When the Soft Keys option is set to ON, the default soft keys are displayed if no
other operation is in progress.
When the Soft Keys option is set to OFF, the default soft keys are only
displayed when a soft key is pressed, and they disappear if no operation is
performed for 10 seconds.
Key Beep
This option controls whether or not the keys make a noise when you press
them.
Cursor Readout
Chapter 7: Setting Up the System Defaults
7-8
hsb2 Plus Series Fishfinders
MOB Data
MOB Data
This option controls whether MOB data is based on position data, or on dead
reckoning (DR). Dead reckoning normally provides a better indication of the
course to an object in the water, on the assumption that your vessel and the
object are both subject to the same tide and wind effects.
Autopilot Pop Up
This option controls whether or not the autopilot pop up is displayed. When set
to ON, when the status and locked heading of the autopilot changes, they are
displayed in a pop up box. The box is removed from the display after two
seconds.
When Autopilot Pop set to OFF, the pop up box is disabled.
Menu Timeout Period
With no timeout set, menus and soft key labels remain displayed until you
clear them by pressing ENTER, CLEAR or the appropriate dedicated key.
If you set a value here, the menus and soft key labels will be cleared if a key has
not been pressed for the specified number of seconds.
This setting does not affect the default soft key labels, which are controlled by
the Soft Keys option (see above).
Units
You can set the units for speed, depth and temperature. The units you set will
be used to display all data, including information received from other
instruments on the system. However, the distance units do not affect the
instrumented range of the radar, which is always in nautical miles.
Variation Source
The variation value is the difference between True and Magnetic direction
data for heading or bearing values. The Variation Source option provides soft
keys for selecting Auto or Manual variation mode, displays the current
variation value for each and highlights the currently selected mode.
Auto Mode (available in systems with hsb2 Radar)
If you select Auto mode, the unit obtains the value of variation automatically,
normally from received data. The variation value that is used depends on the
data available, and is selected in the following order of priority:
1. Variation value from the same source as the heading data:
• If heading data is being taken from NMEA, then variation is also taken
from NMEA
• If heading is taken from SeaTalk, then SeaTalk variation is used
Chapter 7: Setting Up the System Defaults
7-9
• If heading data is being taken from NMEA, but no NMEA variation is
available, then variation is taken from SeaTalk
• If heading is taken from SeaTalk, but no SeaTalk variation is available,
then variation is taken from NMEA
3. A calculated variation value, using position data, if no SeaTalk or NMEA
value is available
4. The current manual variation value, if no SeaTalk or NMEA value and no
position data is available
Manual Mode
If you select Manual mode, by pressing either of the MANUAL keys, you can
specify the local variation value according to the area in which you are
operating. Press the appropriate MANUAL key to adjust the variation up or
down, to a maximum of 30° East or West.
This value is then transmitted to any other SeaTalk instruments on your
system. It is retained if you turn the display off and on again.
In Manual mode, incoming NMEA variation is ignored. However, if the
variation is changed on another SeaTalk instrument, the new value is used and
the manual value that is displayed is updated.
Note: The Manual variation value defaults to 0°, so it is important to set up a
value if variation is not available from an external source.
Bridge NMEA Heading
The hsb2 Plus Series Fishfinder displays bridge NMEA input data to the
SeaTalk bus (see Section 2.7). The Bridge NMEA Heading option can be used
to prevent NMEA heading data being bridged onto the SeaTalk bus.
For example, if you have a course computer connected on SeaTalk and
NMEA, and an active compass connected on NMEA (for MARPA), SeaTalk
data overrides NMEA data in the course computer.
You should therefore switch OFF the Bridge NMEA Heading option to ensure
the course computer receives the same NMEA heading input as the rest of the
system.
NMEA-Out Set Up
This option lets you disable the transmission of specific NMEA sentences,
which may be necessary if you have other instruments sending the same data
as your fishfinder. See Appendix D for a list of NMEA input messages.
Bridge NMEA
Heading
2. Variation value from a different source:
7-10
hsb2 Plus Series Fishfinders
NMEA-Out Set Up
For example, if the DPT (depth) sentence is set ON but the fishfinder’s
transducer is designed to sense temperature and speed only, the depth value
will be transmitted as zero. If you also have an ST60 Depth instrument
installed, there may be confusion between the zero depth sent by the fishfinder
and the actual depth sent by the ST60. Turning OFF the DPT sentence disables
the reading from the fishfinder.
The factory default for all NMEA sentences is transmission ON. Disable the
sentence by selecting the OFF soft key. The following table displays the
available NMEA sentences and their meanings.
Table 7-2:
NMEA Sentences
Sentence
Meaning
APB
Autopilot Sentence “B”
BWC
Bearing & Distance to Waypoint
BWR
Bearing & Distance to Waypoint – Rhumb Line
DBT
Depth Below Transducer (see note below)
DPT
Depth (see note below)
MTW
Water Temperature
RMB
Recommended Minimum Navigation Information
RSD
Radar System Data
RTE
Routes
TTM
Tracked Target Message
VHW
Water Speed and Heading
VLW
Distance Travelled through the Water
WPL
Waypoint Location
GGA
Global Positioning System Fix Data
GLL
Geographic Position – Latitude/Longitude
RMA
Recommended Minimum Specific Loran-C Data
RMC
Recommended Minimum Specific GPS/TRANSIT Data
VTG
Course Over Ground and Ground Speed
The messages will not stop transmitting until after ENTER is pressed. Consult
your NMEA instrumentation documentation to determine which strings
should remain ON.
Note: TheL760/RC Plus outputs the same depth value for DBT and DPT, regardless of the Depth Offset value in Sonar Setup.
Chapter 7: Setting Up the System Defaults
7-11
You can set up an integrated system so that radar and chartplotter displays
connected via SeaTalk can display each other’s cursors.
Cursor echo functions so that you can display a chart cursor on the radar
picture, or a radar cursor on the chart picture (you cannot display a remote
radar cursor in a radar window nor a remote chart cursor in a chart window).
When the appropriate options are switched on, each display shows its own
cursor, plus the cursor of the other display with appropriate cursor text (RDR or
CHRT) to indicate its origin. This means that you could move the cursor over a
target on the radar display, and check the identity of the target by looking at the
radar cursor position on the chartplotter.
Press the CURSOR ECHO soft key to display the cursor transfer soft keys. The
following options can be toggled ON or OFF:
• Radar Cursor In: displays the cursor from another radar on the chart display or chart window (default - OFF).
• Chart Cursor In: displays the cursor from another or chartplotter on the
radar display or radar window (default - OFF).
Note: The remote display must have SeaTalk Cursor Out enabled.
• SeaTalk Cursor Out: enables the output, onto SeaTalk, of the display’s
own cursor (default - OFF).
• Cursor Echo Local: echoes the cursor position between open windows on
the same display (default - ON).
If you set the options to OFF, no cursor echo information is displayed.
Date and Time Settings
Set your preferred date format (DD/MM/YY or MM/DD/YY) and time
format (12 or 24 hour). If you wish to display local time, use the soft keys to
change from UTC to the required time offset. This can be up to plus or minus
12 hours, in hourly steps.
GPS SOG/COG Filter
The SOG/COG filter averages the velocity vectors to compensate for the
oscillating motion of the vessel, giving a clearer indication of the vessel’s
course and speed. The filter does not affect the calculation of the GPS position.
The velocity vectors calculated from the GPS Signal give an instantaneous
measure of speed and direction of the GPS antenna. The COG and SOG can
therefore seem erratic under certain conditions. For example, when a vessel is
moving slowly through rough seas, the antenna moves from side to side as
well as in the direction of the vessel.
Cursor Echo
(Systems with
Radar Display)
Cursor Echo (Systems with Radar Display)
7-12
hsb2 Plus Series Fishfinders
Compass Set Up
Slow moving vessels, or vessels sailing in rough seas will benefit from a high
setting, whereas a power boat that can quickly change speed and direction will
benefit from a low setting.
Select the SOG/COG filter setting as required. This can be set to HIGH,
MEDIUM or LOW.
Compass Set Up
This option is used to calibrate a Raymarine heading sensor such as the
Pathfinder Smart Heading System. Controls are provided for LINEARISE
COMPASS which detects and corrects for heading errors caused by metal
objects, and ALIGN HEADING which matches the displayed heading to a known
heading or transit.
Refer to the Handbook supplied with your heading sensor for more details.
Language
Select the language in which you wish information to be displayed. The
selected language will be used for screen text, labels, menus and options, but
will not affect the letters displayed by the context-sensitive cursor. The
language setting also affects the display format for lat/long position
information.
Simulator
The simulator allows you to operate your display without data from the
transducer and/or external data sources. The system set up simulator options
have the following functions:
• Data provides simulated numerical data, and a waypoint display.
• Radar (integrated systems with a radar display) provides simulated radar
picture, with example targets. The picture does not change if you change
the range, although the range rings are adjusted (see Pathfinder Radar
documentation).
• Both provides simulated data and radar picture.
When the simulator is switched on, a SIMULATOR data box is displayed during
operation, showing the simulation selected.
Fishfinder simulator mode is set in the Sonar setup menu, described in
Section 7.4.
7-13
7.4 Fishfinder Set Up Parameters
The SONAR SET UP option allows you to set up the fishfinder according to your
system configuration and your personal preferences.
The following table lists the Sonar Set Up parameters and their options, shows
the factory default setting, and provides a space for you to make a note of your
new default setting. Each parameter is described in the following subsections.
Table 7-3:
Fishfinder Set Up Parameters
Parameter
Options
Factory
Default
TARGET DEPTH ID
OFF
ON
OFF
COLOR BAR
OFF
ON
ON
DEPTH DIGIT SIZE
LARGE
SMALL
LARGE
SONAR HSB MODE
REPEATER
MASTER
MASTER
DEPTH OFFSET
Value
0.0
SPEED CALIBRATE
0% to 200%
100%
SONAR HISTORY
LARGE or SMALL
LARGE
TEMP CALIBRATE
-9.0 °F to +9.0 °F
0°F
DEPTH RANGE
(L1250/RC Plus only)
3000 ft (1000 m)
5000 ft (1700 m)
3000 ft (1000 m)
SONAR SIMULATOR
OFF
ON
OFF
New Default
Target Depth ID
You can select whether or not the depth is displayed for displayed fishfinder
echoes. When Target Depth ID is set to ON, the depth is displayed just above
each fish echo. When set to OFF, the depth of each echo is not displayed.
Color Bar
The color bar indicates the range of echoes displayed in each color (shade of
gray for monochrome displays). When set to ON the color bar is displayed on
the right hand side of the display.
Fishfinder Set Up
Parameters
Chapter 7: Setting Up the System Defaults
7-14
hsb2 Plus Series Fishfinders
Depth Digit Size
Depth Digit Size
The depth under the boat is displayed in the bottom left hand corner of the
fishfinder display. You can select small or large digits for the depth display.
Sonar HSB Mode
You need to specify if the Fishfinder display is a master display (directly
connected to the transducer), or a repeater display (connected via hsb2 to a
Fishfinder master display). Depth data is sourced from a master display.
Depth Offset
The depth offset is added to the measured depth value before it is displayed.
You can specify the depth as a positive value – Waterline Offset, or a negative
value – Keel Offset. The depth offset can be set adjusted in 0.1 increments of the
units you have set for Depth Units: meters, fathoms, or feet. See Section 7.3,
System Set Up Parameters.You can only specify depth offset for a master
display.
Speed Calibrate
If the transducer is equipped with a speed paddle wheel, the fishfinder display
detects and displays the speed of the boat through the water. The speed
calibrate option allows you to adjust the displayed speed so that it matches
your actual speed through the water. You can adjust the displayed speed, for a
master display, from 1% to 200%.
If the Fishfinder reading is too low, set Speed Calibration to more than 100%.
If the Fishfinder reading is to high, set Speed Calibration to less than 100%.
Temperature Calibrate
The fishfinder display detects and displays the temperature of the water. The
temperature calibrate option allows you to adjust the displayed temperature.
You can adjust the displayed temperature, for a master display, by -9.0°F to
+9.0°F.
Sonar History
Sonar History determines the number of data sample columns that appear on
the screen at one time. The options are: SMALL, which displays 240 columns of
data or LARGE, which shows 480 columns. Information displayed in a single
column using the LARGE setting would occupy two columns with SMALL. As a
result, twice as much data history is displayed under the LARGE setting. Data
displayed using SMALL appears wider and scrolls across the screen faster.
7-15
The default setting is LARGE.
Depth Range (L1250 Plus and L1250RC Plus only)
The L1250 Plus and L1250RC Plus can be set to detect a maximum depth of
5000 ft (1700 m). However, other hsb2 devices only recognize a maximum
depth of 3000 ft (1000 m). If another hsb2 device is connected to the fishfinder,
you should leave the Depth Range at the default setting of 3000 ft. Set the
Depth Range for 5000 ft only if no other hsb2 device is connected.
Sonar Simulator
The simulator allows you to operate your display without data from the
transducer, in order to become familiar with the fishfinder features and
functions.
Depth Range
(L1250 Plus and
L1250RC Plus only)
Chapter 7: Setting Up the System Defaults
7-16
hsb2 Plus Series Fishfinders
Chart Set Up
Parameters
(Raychart Models)
7.5 Chart Set Up Parameters (Raychart Models)
For Fishfinders with the Raychart feature installed, the CHART SET UP option
allows you to set up the chartplotter according to your system configuration
and your personal preferences.
The following table lists the Chart set up parameters and their options, shows
the factory default setting, and provides a space for you to make a note of your
new default setting. Each parameter is described in the following subsections.
Table 7-4:
Chart Set Up Parameters
Parameter
Options
CUSTOMIZE CHART
See below for details
PLOTTER MODE
OFF, ON
OFF
CHART
ORIENTATION
NORTH UP, COURSE UP,
HEAD UP
NORTH UP
OBJECT
INFORMATION
OFF, ON POINTS, ON ALL
ON ALL
PALETTE (COLOR LCD)
SHADE, SUNLIGHT
SUNLIGHT
WAYPOINT SYMBOLS
OFF, ON
ON
WAYPOINT NUMBERS
OFF, OFF
ON
DEFAULT WAYPOINT
SYMBOL
,
Factory Default
,
New Default
,
HEADING VECTOR
OFF, 3 MINS, 10 MINS,
INFINITE
OFF
COG VECTOR
OFF, 3 MINS, 10 MINS,
INFINITE
OFF
TIDE VECTOR
OFF, 10 MINS, 1 HOUR,
INFINITE
OFF
RADAR/CHART
SYNCH
OFF, ON
OFF
DATUM SELECTION
WGS 84, LOCAL
WGS 84
POSITION OFFSET
OFF, ON
OFF
Customize Chart
This provides a list of chart options, enabling you to specify how the chart
features are displayed. Most options can be toggled between on, off and
custom. Custom passes on/off control to the SCREEN soft keys (see
Customizing the Screen Presentation Options on page 3-26).
The following features can be set using Customize Chart, factory default
settings are shown in bold type:
Chapter 7: Setting Up the System Defaults
7-17
• chart text size (small, normal, large)
• chart display (simple, detailed)
• chart boundaries (on, off, custom)
• spot soundings (on, off, custom)
• depth shading limit (set the limit)
• depth contours (on, off, custom)
• depth contour display (set the upper and lower limits)
• nav marks (on, off, custom)
• nav marks icon (international, US)
• light sectors (on, off, custom)
• caution and routing data (on, off, custom)
• marine features (on, off, custom)
• land features (on, off, custom)
• icon display (simple, detailed, custom)
The factory default for CUSTOM options is OFF. This can be changed using the
SCREEN soft key in chart mode.
Plotter Mode
Plotter Mode enables you to zoom into a smaller area, even when no chart data
is available for that scale. This allows you use the chartplotter functions at
large scales even when a chart card is not installed.
Chart Orientation
The chart orientation is normally North Up, but can be changed to Course Up
or Head Up if heading data is available. The orientation modes give the
following displays:
• North Up: The chart is displayed with north upwards. As you change
heading, the ship’s heading marker moves. This is the default mode, and is
the only mode available if there is no heading data.
• Course Up: The chart is stabilized and displayed with the currently
selected course upwards. If you select a new course, the picture rotates to
display the new course upwards.
The reference used for the Course Up depends on the information available. The first available in the following is used:
i. A locked heading over a SeaTalk connection
ii. The heading at the time Course Up was selected
To update the Course Up reference while Course Up is the current mode,
re-select Course Up from the set up menu.
Plotter Mode
• chart text (on, off, custom)
7-18
hsb2 Plus Series Fishfinders
Object Information
• Head Up: The chart is displayed with the vessel’s current heading
upwards. As the heading changes the chart will rotate.
Object Information
You can set Object Information ON ALL, ON POINTS or OFF to determine when
an object identification pop-up is displayed. When set to ON ALL, the
information pop up is displayed when the cursor is placed over any chart area
for two seconds. ON POINTS enables the information pop up when the cursor is
placed over a displayed chart object and OFF disables the information pop up.
Palette (Color LCDs only)
The Palette option lets you specify which color palette, SHADE or SUNLIGHT,
the display uses.
The Sunlight palette is optimized for best display clarity in bright sunlight. In
dimmer conditions you may prefer the shade palette.
Waypoint Options
Waypoint Symbols controls whether or not the waypoints are shown on the
Chart display, with their appropriate symbols. The active waypoint, and
waypoints in the current route are always shown.
Waypoint Numbers controls whether or not the waypoint numbers are
shown for any waypoints in the current route.
Default Waypoint Symbol lets you select the symbol you want used for
waypoint display.
Vectors
Heading, Tide and Course Over Ground vectors can be displayed as a line
from your vessel. The length of the vector is determined by your choice of
SOG and the time period. An infinite vector extends to the edge of the chart
screen.
Heading Vector indicates your current heading.
COG Vector indicates your course over ground.
Tide Vector indicates the tide angle. Tide information is calculated from the
speed through water, compass and position data.
7-19
Radar/Chart Synch (Systems with Radar Display)
If you have an hsb2 Plus Series combined Fishfinder/Chartplotter display
connected via hsb2 to a Pathfinder Plus Series Radar display, you can select
Radar/Chart Synch ON or OFF. When set ON with chart and radar windows
displayed, FIND SHIP can be used to synchronize the radar and chart images.
The chart is redrawn so that its center matches that of the radar display. The
radar is redrawn to the scale and heading mode of the chart.
Datum Selection
You can select either WGS 84 or LOCAL datum. In LOCAL mode, you are
presented with a list of datums; use the trackpad to scroll through the list, then
press ENTER to select the option and close the menu.
When you change datum selection, the system attempts to set any connected
GPS to the new mode, using SeaTalk and NMEA set up commands. A
message shows whether the set up was successful or not.
CAUTION:
Changing the chart datum does not cause any waypoint or routes stored
in the chartplotter to move. Waypoints and routes may therefore appear
to be at different positions when you change the datum.
When adding waypoints numerically to the waypoint list, or via SeaTalk,
hsb2, or NMEA, it is important that they are referenced to the same
datum that the chart is to be operated in.
Position Offset
You can offset the vessel position to allow for differences between the GPS
and paper chart data. This may be useful if you are using a datum that is not
available on the Chartplotter, or if you are referring to a paper chart drawn to
unknown datum.
You can change the offset by moving the cursor to the known vessel position.
This offset is applied to all incoming position data. The default offset value is
zero.
When position offset is switched on, all displayed vessel position data is
annotated (C) to indicate it has been corrected.
Radar/Chart Synch
(Systems with
Radar Display)
Chapter 7: Setting Up the System Defaults
7-20
hsb2 Plus Series Fishfinders
Position Offset
➤
To switch the position offset on/off:
1. Select the POSITION OFFSET option, then press the OFFSET OFF ON soft key
to toggle the option on/off. The last selected offset value is added to position data and the vessel is displayed at the corrected position.
➤
To set a new offset value:
1. Select the POSITION OFFSET option, then press the SET UP OFFSET soft key.
If necessary, position offset is automatically toggled on.
2. Use the trackpad to move the cursor to the required vessel position; the cursor position is displayed in a position offset data box.
3. Press the ACCEPT OFFSET soft key, the vessel is displayed at the new position. Press ENTER to return to the default display.
➤
To set the offset value to zero:
1. Select the POSITION OFFSET option, then press the SET UP OFFSET soft key
2. Press the CANCEL OFFSET soft key. The position offset value is set to zero.
Chapter 8: Maintenance and Problem Solving
8-1
Chapter 8: Maintenance and Problem
Solving
This chapter provides information on routine maintenance and on possible
causes of problems you may experience with your hsb2 Plus Series display
unit.
8.1 Maintenance
WARNING:
The display unit contains high voltage. Adjustments require specialized
service procedures and tools only available to qualified service
technicians - there are no user serviceable parts or adjustments and the
operator should not attempt to service the equipment. The operator
should not remove the rear cover of the display.
Switch off the display unit before removing the power cord.
Routine Checks
• Examine the cables for signs of damage, such as chafing, cuts or nicks.
• Check that the cable connectors are firmly attached.
Cleaning Instructions
Cleaning the Display
CAUTION:
Take care when cleaning the display. Use the display cleaning cloth
provided. Avoid wiping the display screen with other types of dry cloth this could scratch the screen coating.
Do not use acid, ammonia based or abrasive products.
• Ensure power is off, wipe the display clean with a damp cloth.
• If necessary, use IPA (isopropyl alcohol) or a mild detergent solution to
remove grease marks.
Cleaning the Transducer
Sea growth can collect quickly on the bottom of the transducer, this can reduce
the performance in just a few weeks. To prevent the build-up of sea growth,
coat the transducer with a thin layer of paint.
Maintenance
The LCD display is a sealed unit. Maintenance procedures are therefore
limited to the following periodic checks:
8-2
hsb2 Plus Series Fishfinders
Use only a water-based antifouling paint, or a water-based paint specifically
designed for transducers. Apply the paint with a brush.
If your transducer becomes fouled or stops working because of sand or sea
growth, use a stiff brush to clean it. You may sand the surface with a fine-grit
wet or dry sandpaper (#320 grade or finer), but this will affect the performance
of the unit when the boat is moving at higher speeds.
The paddle wheel mechanism may become jammed by dirt, grit or barnacles.
Work this out of the mechanism, then clean the unit with soap and water or
alcohol.
Cleaning the Hull
Use caution when sanding or cleaning the outside of the hull near the
transducer.
CAUTION:
Harsh cleaning solvents such as acetone may damage the transducer.
EMC Servicing and Safety Guidelines
EMC Servicing and
Safety Guidelines
• Raymarine equipment should be serviced only by authorized Raymarine
service technicians. They will ensure that service procedures and replacement parts used will not affect performance. There are no user serviceable
parts in any Raymarine product.
• Some products generate high voltages, so never handle the cables/connectors when power is being supplied to the equipment.
• When powered up, all electrical equipment produces electromagnetic
fields. These can cause adjacent pieces of electrical equipment to interact
with one another, with a consequent adverse effect on operation. In order to
minimise these effects and enable you to get the best possible performance
from your Raymarine equipment, guidelines are given in the installation
instructions, to enable you to ensure minimum interaction between different items of equipment, i.e. ensure optimum Electromagnetic Compatibility (EMC).
• Always report any EMC-related problem to your nearest Raymarine
dealer. We use such information to improve our quality standards.
• In some installations, it may not be possible to prevent the equipment from
being affected by external influences. In general this will not damage the
equipment but it can lead to spurious resetting action, or momentarily may
result in faulty operation.
Chapter 8: Maintenance and Problem Solving
8-3
8.2 Resetting the System
There are three types of reset available for the Fishfinder display:
• Factory Reset: This resets all values back to their original factory settings.
CAUTION:
The factory reset clears the Marks database, the chartplotter Waypoints
and Routes databases, the sonar depth offset, and speed and temperature
calibrations. The factory reset also returns the sonar repeater to its
master mode.
• Power-On Reset: When you turn the display off and on again, the screen
reverts to the fishfinder or chart picture with all windows cleared.
• Picture Reset: Press and hold the DISPLAY key for two seconds to return
the screen to the full-screen picture of the top window with all windows
cleared.
At power-on, the last-used values are retained for all the options, except for
those listed in the following table which are reset to the factory default each
time.
➤
Power On Default Settings
Item
Power-on setting
Heading Mode
Brightness
Mono LCD
Color LCD
North Up (chart)
ON at 100%
ON at 42% if previously left ON, or else
OFF if previously set to OFF.
To perform a factory reset:
1. Press MENU.
2. Press the SYSTEM SET UP soft key to display the System Set Up page (see
Section 7.3 for details).
3. Press and hold MENU for 5 seconds.
A countdown timer is displayed. If you release the MENU key before the
timer reaches zero, the reset is not performed.
When the reset request has been accepted, the system restarts.
The factory default settings are listed in Section 7.3.
Resetting the
System
Table 8-1:
8-4
hsb2 Plus Series Fishfinders
8.3 Problem Solving
All Raymarine products are, prior to packing and shipping, subjected to
comprehensive test and quality assurance programs. However, if this unit
should develop a fault, please refer to the following table to identify the most
likely cause and the corrective action required to restore normal operation.
If you still have a problem after referring to the table below, contact your local
dealer, national distributor or Raymarine Technical Services Department for
further advice. Always quote the product serial numbers. The display unit
serial number is printed on the back of the unit.
Common Problems and Their Solutions
Table 8-2:
Common Fishfinder Problems
Problem Solving
Problem
Correction
Display does not function
1. Make sure that the power supply cable is sound and that
all connections are tight and free from corrosion.
2. Check the system fuse.
Display “freezes”
1. Check the scroll speed is not set to zero.
2. Check the transducer cable for damage. If damaged, the
cable and transducer must be replaced as a unit.
Fishfinder does not see bottom or
fish
1. If you have a transom-mount transducer, check that the
transducer hasn’t kicked-up on hitting an object.
2. Check that the gain is not set too low.
3. Check that the transducer is within 10° of vertical.
4. Check that the transducer face is not covered or fouled. If
necessary clean the transducer.
5. Check the voltage from the power source; if this is too low
it can affect the transmitting power of the Fishfinder.
Fishfinder does not display fish
1. Fish arches are not displayed if the boat is stopped - fish
appear on the display as straight line.
2. Ensure the transducer is within 10 ° of vertical.
3. Check that the gain is not set too low.
Fishfinder display is unreliable at
high boat speeds
1. Turbulence around the transducer may be confusing the
unit.
Fishfinder displays a lot of background noise
1. Check that the gain is not set too high.
2. Check that the transducer is mounted correctly and is
clean.
Fishfinder speed or log readings are
wrong
1. Check that the transducer paddle wheel is clean.
2. If necessary add a speed offset.
3. If receiving SeaTalk speed, unplug the SeaTalk connector.
Fishfinder temperature readings are
wrong
1. If necessary, adjust the TEMP CALIBRATE parameter.
2. If receiving SeaTalk temperature, unplug the SeaTalk connector.
Chapter 8: Maintenance and Problem Solving
8-5
How to Contact Raymarine
On the Internet
Visit the Raymarine World Wide Web site for the latest information on
Raymarine electronic equipment and systems at:
www.raymarine.com
Customer Support
Navigate to the Customer Support page for links to:
• Finding Factory Service locations and Authorized Dealers near you
• Registering your Raymarine products
• Accessing handbooks in Adobe Acrobat format
• Downloading RayTech software updates
• Accessing the Raymarine solution database
In the US
Accessories and Parts
Many Raymarine accessory items and parts can be obtained directly from
your authorized Raymarine dealer. However, if you are in need of an item not
available from the retailer, please contact Raymarine Technical Services at:
800-539-5539 ext. 2333, or
603-881-5200.
Technical Service is available Monday through Friday 4:00 AM to 6:00 PM
Eastern Time.
Please have the Raymarine item or part number ready when calling if placing
an order. If you are not sure which item is appropriate for your unit, you should
first contact the Technical Support Department to verify your requirements:
800-539-5539 ext. 2444, or
603-881-5200.
How to Contact
Raymarine
Clicking the Find Answers link routes you to our solution database. Search
questions and answers by product, category, keywords, or phrases. If the
answer you are seeking is not available, click the Ask Raymarine tab to
submit your own question to our technical support staff, who reply to you by email.
8-6
hsb2 Plus Series Fishfinders
Technical Support
For technical support, call:
800-539-5539 ext. 2444, or
603-881-5200.
Our Technical Support Specialists are available to answer questions about
installing, operating and trouble-shooting all Raymarine products.
Questions can be sent directly to our Technical Support Department via the
Internet. Point your browser to www.raymarine.com and click on the
Customer Support link. From there, select Find Answers and click the Ask
Raymarine tab.
Product Repair and Service
In the unlikely event your Raymarine unit should develop a problem, please
contact your authorized Raymarine dealer for assistance. The dealer is best
equipped to handle your service requirements and can offer timesaving help in
getting the equipment back into normal operation.
In the event that repairs can not be obtained conveniently, product service may
also be obtained by returning the unit to:
How to Contact
Raymarine
Raymarine, Inc.
Product Repair Center
22 Cotton Road, Unit D
Nashua, NH 03063-4219
The Product Repair Center is open Monday through Friday 8:15 a.m. to
5:00 p.m. Eastern Time. All products returned to the Repair Center are
registered upon receipt. A confirmation letter will be sent to you
acknowledging the repair status and the product’s reference number. Should
you wish to inquire about the repair status of your unit, contact the Product
Repair Center at:
800-539-5539
Please have the product reference number, or unit serial number, ready when
you call. We will do everything possible to make the repair and return your
unit as quickly as possible.
Chapter 8: Maintenance and Problem Solving
8-7
In Europe
In Europe, Raymarine support, service and accessories may be obtained
from your authorized dealer, or contact:
Raymarine Ltd
Anchorage Park
Portsmouth, Hampshire
England PO3 5TD
Tel +44 (0) 23 9269 3611
Fax +44 (0) 23 9269 4642
Technical Support
The Technical Services Department handles inquiries concerning installation,
operation, fault diagnosis and repair. For technical helpdesk contact:
Tel:+44 (0) 23 9271 4713
Fax: +44 (0) 23 9266 1228
Accessories and Parts
Raymarine accessory items and parts are available through your authorized
Raymarine dealer. Please refer to the lists of component part numbers and
optional accessories in the Installation chapter of this manual, and have the
Raymarine part number ready when speaking with your dealer.
If you are uncertain about what item to choose for your Raymarine unit, please
contact our Customer Services Department prior to placing your order.
Worldwide Support
Please contact the authorized distributor in the country.
Worldwide Support
Questions can be sent directly to our Technical Support Department via the
Internet. Point your browser to www.raymarine.com and click on the
Customer Support link. From there, select Find Answers and click the Ask
Raymarine tab.
8-8
hsb2 Plus Series Fishfinders
Worldwide Support
A-1
Appendix A: Specifications
hsb2 Plus Series Fishfinder Displays
General
Approvals:
CE - conform to
FCC - conforms to
Size:
L755RC
SL760, L760RC
L1250, L1250RC
89/336/EEC (EMC), EN60945:1997
Part 80 (47CFR) and Part 2 (47CFR)
8.8" x 8" x 4.72" (223 x 204 x 120 mm), excluding bracket
8.8" x 8.1" x 6" (223 x 205 x 152 mm), excluding bracket
11.5" x 11.4" x 5.46" (292 x 289 x 139 mm), excluding bracket
Weight: L755RC
SL760, L760RC
L1250, L1250RC
7.72 lbs (3.5 kg)
8.16 lbs (3.7 kg)
12.8 lbs (5.8 kg)
Mounting
Bracket with panel mount option
Power:
External 10.7 - 44 VDC required
Floating earth/fully isolated
10 W consumption with full backlighting
20 W consumption with full backlighting
30 W consumption with full backlighting
L755RC
SL760, L760RC
L1250, L1250RC
Environmental:
Operating/Storage
Temp. Range:
Mono LCD
Color LCDs
Humidity limit:
Waterproof to CFR46; suitable for external mounting
Controls:
11 defined keys, 4 soft keys and trackpad
Cursor:
Context sensitive, provides range/bearing or lat/lon
Display Type:
L755RC
SL760, L760RC
L1250, L1250RC
-10°C to +70°C
-10°C to +50°C
up to 95% at 35°C non-condensing
7" Monochrome Film Super Twist Neumatic (FSTN) LCD,
with 4 gray scales
7" Color Thin Film Transistor (TFT) LCD
10.4" Color TFT LCD
Resolution:
Mono LCD
Color LCDs
320 x 240 (1/4 VGA)
640 x 480 (VGA)
Display Size:
L755RC
SL760, L760RC
L1250, L1250RC
143 mm x 111 mm
136 mm x 100 mm
211 mm x 154.4 mm
Illumination
Screen: Color LCD - Backlighting adjustable 0% to 100%
Monochrome - 8 levels of backlighting
Keypad: 3 levels of backlighting
Appendix A:
Specifications
Appendix A: Specifications
A-2
hsb2 Plus Series Fishfinders
Appendix A:
Specifications
Mono LCD Contrast
64 levels, selectable via soft keys.
Languages
UK English, US English, Danish, French, German, Dutch, Italian,
Icelandic, Norwegian, Portuguese, Spanish, Swedish, Finnish
Connectors
7 pin transducer
3 pin HSB input/output
3 pin SeaTalk input/output
7 pin power including 2 NMEA input channels
4 pin NMEA output
Interfaces
1 x SeaTalk, receive and transmit
1 x hsb2, receive and transmit
2 x NMEA 0183, receive
1 x NMEA 0183, transmit
C-MAP cartridge reader - 2 slots (Raychart models only)
Man Overboard
(MOB Mode)
Mark placed with course line; readout shows range, bearing,
lat/lon of MOB and time elapsed since MOB.
Screen Functions
Full, half and quarter screens available dependent on function
Data Boxes
Up to six user selectable information boxes
Fishfinder Features
Output Power:
L755RC,L760, L760RC
L1250, L1250RC
600 Watts RMS
1000 Watts RMS
Frequency
Dual 50 KHz and 200 KHz
Depth:
L755RC,L760, L760RC
L1250, L1250RC
1 to 3000 ft (1000 m)
1 to 5000 ft (1700 m) 1
Target Detection
Sonar echo with target depth readout
Display Windows
Full or split screen of either frequency, digital data and chart (if
Raychart equipped). Radar screen if available via hsb2.
Display Modes
A-Scope with bottom coverage, Bottom Lock, Auto or Manual
Zoom, White Line
Waypoints
998 waypoints entered at cursor or vessel position
Color Options
Background color selection: black, dark grey, light grey, white
or blue.
Two color palettes
Adjustable color thresholds
Transducer
Transom mount, in-hull, or thru-hull
1
Other hsb2 devices recognize a maximum depth of only 3000 ft (1000 m). If another hsb2 device is connected,
you should leave the Depth Range setting at the default of 3000 ft. Set the Depth Range for 5000 ft only if no other
hsb2 device is connected, using the Depth Range Sonar Set Up Parameter as described on page 7-15.
Appendix A: Specifications
A-3
Cartography
C-MAP® NT and NT+ micro cartridges available from C-MAP®
Chart of the world built in
Display Windows
Chart, Radar, Data Log, BDI, CDI, Navdata
Chart Scaling
1/64 nm (if cartographic data is available) to 4000 nm
Presentation Modes
North up (selectable True or Magnetic) Head up or Course up
Waypoints
998 waypoints entered via cursor, lat/lon, range and bearing from
present position or at vessels position.
16 character name can be assigned
Waypoint Transfer
hsb2, current route via SeaTalk, NMEA
Routes
A route plan may contain up to 50 waypoints. Up to 20 routes can
be stored in the units internal memory
Track History
5 tracks with up to 750 points in each can be stored in the units
internal memory
Alarms
Programmable arrival, cross track error, anchor drift, position fix/
data loss warning, grounding, countdown timer and alarm clock
Navigation Information
Own ships position in Lat/Lon, XTE, TTG and SOG/COG selectable.
Mileage scale ruler. Bearing and distance to waypoint. Bearing and
distance to cursor, SeaTalk data (see ‘interfacing’ section)
Variation Source
Auto (SeaTalk/NMEA/Internal algorithm) or Manual
Chart/Radar Synchronization
User selectable in split screen mode provided radar/chart data
available
Interfacing
High Speed Bus
Fully independent use of remote Chart data if present on hsb2. Full
remote control and display of Radar data if present on hsb2.
SeaTalk Input
Depth, Speed Over Ground & Course Over Ground, Position,
Waypoint number, range, bearing and time to go, Speed through
water, Time, Cross Track Error, Heading, Wind, Date, Log/Trip, Pilot
Status, Temperature, Man Overboard, and cursor position
NMEA Input
NMEA 0183 (GLL, GGA, GLC, GTD, VTG, BWC, BWR, RMA, RMB,
RMC, XTE, VHW, HDG, HDM, HDT, DBT, DPT, APB,VLW, MWV,
MTW,WPL, RTE and ZDA)
SeaTalk Output
Cursor data, Guard zone alarm and Navigational data bridged
from NMEA
NMEA Output
APB, BWC, BWR,DBT, DPT,GGA, GLL, MTW, RMA, RMB, RMC, RSD,
TTM, VLW, VHW, VTG, WPL
Appendix A:
Specifications
Chartplotter Features (Units with Raychart)
A-4
hsb2 Plus Series Fishfinders
Appendix A:
Specifications
B-1
Appendix B: Using the Auxiliary Junction Box
The SeaTalk Auxiliary Junction Box is used to connect SeaTalk GPS and
Differential beacon receivers to your hsb2 Plus Series Fishfinder.
Note: With the exception of the Raystar 114, when you use the following Differential Beacon Receiver configurations, the receiver must be set to AUTO
MODE in the GPS Set-Up page. Manual selections will not be accepted. Refer
to Chapter 6 for details.
The recommended method of providing position, course over ground and
speed over ground information to the fishfinder displays is by connection to a
SeaTalk GPS. The hsb2 Plus Series displays are supplied with an Auxiliary
Junction Box, whose main purpose is to make this connection easier. The
junction box has two flying leads, one with a SeaTalk plug for connection to the
display and the other lead is for connection to a 12V power supply (the display
does not provide power for the GPS).
The following sections detail the connections to the Auxiliary Junction Box for
several different types of GPS, including a beacon receiver if installed. Except
for Raystar 114, the differential beacon receivers used are NRD-2A, Apelco
BR101 and the Autohelm Beacon Receiver.
The connections detailed in the following sections ensure that the GPS will
always operate in SeaTalk mode. Note that the Raystar 112LP and Raystar 120
must be the SeaTalk versions.
Appendix B: Using
the Auxiliary
Junction Box
Appendix B: Using the Auxiliary Junction Box
B-2
hsb2 Plus Series Fishfinders
Appendix B: Using
the Auxiliary
Junction Box
Raystar 112, 105, Apelco 182 and 182XT
In order to connect your GPS to your Fishfinder, you must first cut off the 6pin connector and strip back the insulation on all the wires. Connect to the
Auxiliary Junction Box as shown in the first illustration below.
To connect your Differential Beacon Receiver, you must cut off the 5-pin
connector, strip back the insulation on all the wires, and connect to the
Auxiliary Junction Box as shown in the second illustration below.
CAUTION:
Ensure the correct polarity of the 12 V supply before applying display or
SeaTalk power. It is recommended that a multimeter is used to check the
connections.
To Display Unit
SeaTalk Socket
Black
12V
Power
Supply
(fused) Red
Black
Red
Yellow
Green
White
Brown
From
GPS
sensor
D4294-3
To Display Unit
SeaTalk Socket
Black
Red
Yellow
Green
White
Brown
From
GPS
sensor
Black
12V
Power
Supply
(fused) Red
Black
Red
Yellow
White
Green
From
the
DBR
D4295-3
B-3
Autohelm GPS, Z260 and Z273
To connect your GPS to your Fishfinder connect the wires as shown in the first
illustration below.
To connect your Differential Beacon Receiver, you must cut off the 5-pin
connector, strip back the insulation on all the wires, and connect to the
Auxiliary Junction Box as shown in the second illustration below.
CAUTION:
Ensure the correct polarity of the 12 V supply before applying display or
SeaTalk power. It is recommended that a multimeter is used to check the
connections.
To Display Unit
SeaTalk Socket
Black
12V
Power
Supply
(fused) Red
Black
Red
Green
Yellow
White
Brown
From
GPS
sensor
D4297-3
To Display Unit
SeaTalk Socket
Black
Red
Green
Yellow
White
Brown
From
GPS
sensor
Black
12V
Power
Supply
(fused) Red
Black
Red
Yellow
White
Green
From
the
DBR
D4298-3
Appendix B: Using
the Auxiliary
Junction Box
Appendix B: Using the Auxiliary Junction Box
B-4
hsb2 Plus Series Fishfinders
Appendix B: Using
the Auxiliary
Junction Box
Raystar 112LP (SeaTalk version)
To connect your Raystar 112LP to your Fishfinder, refer to the first illustration
below or follow the instructions in Chapter 2.
To connect the Raystar 112LP and your Differential Beacon Receiver, cut off
the 5-pin connector and strip back the red, black, and green wires. Remove the
sleeve from the end of the Raystar 112LP cable to expose the green and brown
wires, then connect to the Auxiliary Junction Box as shown in the second
illustration below.
CAUTION:
Ensure the correct polarity of the 12 V supply before applying display or
SeaTalk power. It is recommended that a multimeter is used to check the
connections.
To Display Unit
SeaTalk Socket
Screen
Red
Yellow
From
GPS
sensor
Black
12V
Power
Supply
(fused) Red
D4292-3
To Display Unit
SeaTalk Socket
Screen
Red
Yellow
Green
Brown
From
GPS
sensor
Black
White
Red
Green
Yellow
From
the
DBR
Black
12V
Power
Supply
(fused) Red
D4296-3
B-5
Raystar 114 Combined GPS and Differential Beacon
Receiver
To connect your Raystar 114 Combined GPS and Differential Beacon
Receiver to your Fishfinder, cut off the 5-pin connector, strip back the
insulation on all the wires and connect to the Auxiliary Junction Box as shown
in the illustration below.
CAUTION:
Ensure the correct polarity of the 12 V supply before applying display or
SeaTalk power. It is recommended that a multimeter is used to check the
connections.
Note: You can use the GPS Set-Up page to manually tune the Raystar 114.
Refer to Chapter 6 for details.
To Display Unit
SeaTalk Socket
Black
White
Red
Yellow
Green
From
Combined
GPS/DBR
sensor
Black
12V
Power
Supply
(fused) Red
D4301_1
Appendix B: Using
the Auxiliary
Junction Box
Appendix B: Using the Auxiliary Junction Box
B-6
hsb2 Plus Series Fishfinders
Appendix B: Using
the Auxiliary
Junction Box
Raystar 120 WAAS Satellite Differential Receiver
To connect your Raystar 120 WAAS Satellite Differential Receiver to your
Fishfinder, connect to the Auxiliary Junction Box as shown in the illustration
below. Optional connections to RTCM are also shown. Note that the green
wire is not used.
CAUTION:
Ensure the correct polarity of the 12 V supply before applying display or
SeaTalk power. It is recommended that a multimeter is used to check the
connections.
%!& '(
!!" "(
!"
#$
%%&
!"
C-1
Appendix C: C-MAP Chart Card Features
The C-MAP chart cards display cartographic features which are derived from
a library of symbols. The library includes a set of 16 x 16 pixel bitmaps which
provide realistically shaped icons for many chart objects. However, these
complex icons can overlap and clutter the display at some scales, so it possible
for the user to select smaller, simple icons. Some chart objects are represented
by text; in such cases conventional abbreviated text is used, for example, M –
mud, R – rock, Wk – wreck
The chartplotter set up menu provides the sub-menu CUSTOMIZE CHART,
which lets you determine how chart features are displayed. You can set the
icon display of many features to custom; you then use the CUSTOM soft key to
switch the customized icons off/on. The factory default for the CUSTOM
options is on.
The chart features controlled from the Customize Chart menu are grouped as
detailed below, some groups are sub-divided into categories
Menu Option
Chart Features
CHART TEXT
Names
CHART BOUNDARIES
Chart Boundaries
SPOT SOUNDINGS
Spot Soundings
DEPTH SHADING LIMIT
Reference Depth
DEPTH CONTOURS
Depths (Bathymetric Lines)
Depth Labels
DEPTH CONTOUR DISPLAY
Depth Contour Range
NAV MARKS
Lights:
Light
Light moire’ effect
Light float
Light vessel
LIGHT SECTORS
Light Sectors
Buoys and Beacons:
Buoy, cardinal
Buoy, installation
Buoy, isolated danger
Buoy, lateral
Buoy, safe water
Buoy, special purpose
Buoy, generic
Beacon, cardinal
Beacon, isolated danger
Beacon, lateral
Beacon, safe water
Beacon, special purpose
Beacon, generic
Signals:
Anchor
Cairn
Chain/Wire
Fog signal
Radar reflector
Top mark
Nav aid, generic
Extended nav aid,
generic
Radar station
Radar transponder
beacon
Radio station
Appendix C: CMAP Chart Card
Features
Appendix C: C-MAP Chart Card Features
C-2
hsb2 Plus Series Fishfinders
Appendix C: CMAP Chart Card
Features
Menu Option
Chart Features
CAUTION & ROUTING DATA
Caution Areas:
Caution area
Fishing facility
Marine farm/culture
Cable, submarine
Cable area
Offshore prod’n area
Pipeline
Pipeline area
Anchor berth
Anchorage area
Cargo transhipment area
Contiguous zone
Continental shelf area
Custom zone
Dumping ground
Exclusive economic zone
Fishery zone
Fishing ground
Free port area
Harbour area (administrative)
Incineration area
Log pond
National territorial area
Sea area
Spoil ground
Straight territorial sea baseline
Submarine transit lane
Territorial sea area
Restricted area
Sea Plane landing area
Military practice area
Tracks and Routes:
Deep water route part
Deep water route
centerline
Fairway
Ferry route
Navigation line
Precautionary area
Radar line
Radar range
Radio calling
Recommended route
centerline
Recommended track
Recommended traffic
lane part
Traffic separation line
Traffic separation,
scheme boundary
Traffic separation,
scheme crossing
Traffic separation,
scheme lane part
Traffic separation,
scheme roundabout
Traffic separation zone
Two-way route part
MARINE FEATURES
Tideways & Currents:
Tideway
Water turbulence
Tide height
Seabed bottom:
Sand waves
Seabed area
Spring
Weed/Kelp
Menu Option
Chart Features
LAND FEATURES
Natural Features:
Coastline
Dune
Hill
Land elevation
Land region
Land
Salt pan
Slope topline
Tree
Vegetation area
Natural Features - Rivers
Canal
Canal bank
Rapids
River
River bank
Waterfall
Lake
Lake shore
ICON DISPLAY
C-3
Cultural Features:
Airport area
Built-up area
Railway
Road crossing
Road part
Runway
Sloping ground
Square
Cable, overhead
Fence
Pipeline, overhead
Pylon
Telepheric
Tunnel entrance
Tank
Complex (detailed) object/Simple object
Building, religious
Building, single
Cemetery
Fortified Structure
Siloway route part
Chimney
Dish aerial
Flagstaff/flagpole
Flarestack
Mast
Monument
Radar dome plane
landing area
Tower
Windmill
Windmotor
Appendix C: CMAP Chart Card
Features
Appendix C: C-MAP Chart Card Features
C-4
hsb2 Plus Series Fishfinders
The following chart features are always displayed:
Appendix C: CMAP Chart Card
Features
Menu option
Chart features
PORTS
Ports:
Berthing facility
Causeway
Checkpoint
Crane
Dam
Distance mark
Dock area
Dry dock
Dyke area
Dyke crown
Floating dock
Gate
Gridiron
Harbour facility
Hulk
Landing place
Landing stairs
Lock basin
Oil barrier
Pile
Pontoon
Ramp
Shoreline construction
Slipway
Weir
Small craft facility
CARTOGRAPHIC
OBJECTS
Line, generic
Area, generic
NATURAL FEATURES
Land area
Bridge
ROCKS
Underwater Rock
WRECKS
Wrecks
Services:
Coast Guard station
Pilot boarding place
Rescue station
Signal station, traffic
Signal station,
warning
Port Information:
Port area
Harbour master
Coast Guard
Police
Customs
Health emergency
Post office
Yacht club
Boat yard
Accessories
Electrical/electronic repairs
Engine repairs
Sailmaker
Fishing/diving gear, SCUBA
Hotel/Inn
Restaurant
Bank/Exchange office
Pharmacy
Port/Marina
Slipway
Boat hoist
Crane
Fuel station
Water
Electricity
Showers
Launderette
Public toilets
Post box
Public telephone
Refuse bin
Visitor’s berth
Chandler
Provisions
Bottle gas
Car Parking
Parking for boat and trailers
Caravan site
Camping site
Sewerage pump-out station
Appendix C: C-MAP Chart Card Features
C-5
Menu option
Chart features
DEPTHS 1
Depth area
DEPTHS 2
Dredged area
DEPTHS 3
Intertidal area
PORTS
Mooring/Warping facility
CAUTION AREAS
Fish haven
OFFSHORE INSTALLATIONS
Diffuser
Obstruction
Production installation
Offshore platform
AREAS, LIMITS
No data area
CARTOGRAPHIC
OBJECTS
Incomplete survey area
NATURAL FEATURES (Ice)
Ice area
Pingo
COMPOSITE OBJECTS
Airport
Anchorage
Channel edge
Deep water route
Defined water
Harbour
Range system
Lighthouse
Mooring trot
Navigation mark, afloat
Navigation mark, fixed in point
Traffic Separation Scheme
System
CARTOGRAPHIC AREAS
Cartographic II25 area
Appendix C: CMAP Chart Card
Features
The following chart features are always displayed:
hsb2 Plus Series Fishfinders
C-6
Appendix C: CMAP Chart Card
Features
D-1
Appendix D: SeaTalk and NMEA Data
The following table defines the data received on the NMEA/SeaTalk ports.
Data sources are listed in order of priority except where indicated.
Data Received
Source
Position (LAT/LON)
SeaTalk, GGA, RMC, RMA, GLL
Position (Loran C TD’s)
GLC, RMA, GTD
Speed and Course Over Ground
SeaTalk, RMC, RMA, VTG
Waypoint Data
SeaTalk, RMB, APB, BWC, BWR, RMB, XTE
Depth
SeaTalk, DBT, DPT
Apparent Wind Angle and Speed
SeaTalk, MWV (relative)
Boat Speed Through Water
SeaTalk, VHW
Total Log and Trip Log
SeaTalk, VLW
Water Temperature
SeaTalk, MTW
Average Boat Speed through the Water
SeaTalk only
Heading
HDG, HDM, HDT, VHW, SeaTalk,
Locked Heading
SeaTalk only (Autopilot / Steering Compass)
Magnetic Variation
SeaTalk, RMC, RMA, HDG
Rudder Angle (not displayed)
SeaTalk only
Time (No priority)
SeaTalk, ZDA, GGA, RMC, GLL, BWC, BWR
Date
SeaTalk, ZDA, RMC
MOB data
SeaTalk only
Autopilot Status (Standby / Auto / Vane / Track)
SeaTalk only
Cursor Range and Bearing (from Chartplotter)
Cursor Range and Bearing (from Radar)
SeaTalk only
SeaTalk, RSD
Global Alarms - Watch alarm, Wind alarm,
Autopilot alarms, Depth alarms.
Waypoint arrival
SeaTalk Only
Waypoint/Route Transfer
SeaTalk, WPL, RTE
SeaTalk, RMB, APB
* If Magnetic Heading is not available, the True Heading and Variation (if available) are used to
generate the magnetic heading.
SeaTalk and
NMEA Data
Appendix D: SeaTalk and NMEA Data
D-2
hsb2 Plus Series Fishfinders
SeaTalk and
NMEA Data
The hsb2 Plus Series display unit transmits the following data, if available,
on SeaTalk:
Data Output
SeaTalk
NMEA Out
Position (LAT/LON)
✔
GGA, GLL, RMC1, RMA
Position (Loran C TD’s)
✔
RMA
Speed Over Ground and
Course Over Ground
✔
RMC, VTG1,, RMA
Waypoint Data
✔
RMB, APB, BWC, BWR1
Depth
✔
DBT, DPT 2
Apparent Wind Angle and Speed
✔
—
Boat Speed Through Water
✔
VHW 2
Total Log and Trip Log
✔
VLW 2
Water Temperature
✔
MTW 2
Heading
✔
VHW 2,3
Magnetic Variation
✔
RMA, RMC
Time
✔
ZDA
Date
✔
ZDA
MOB data
✔
—
Cursor Range & Bearing
✔
RSD4
EBL/VRM Data
—
RSD4
Heading mode
—
RSD4
Radar display range
✔
RSD4
Radar Tracked targets
—
TTM4
Waypoint/Route Transfer
—
WPL, RTE
Global Alarm
Waypoint Arrival Alarm
SeaTalk
—
APB, RMB
1
When available, NMEA OUT data is transmitted from a combined Fishfinder/Chartplotter display or
from a Fishfinder-only unit if connected to a Chart display via hsb2.
2
Fishfinder data.
3
Bridged from NMEA if selected in the System Set Up menu.
4
When available, NMEA OUT data is transmitted from a Fishfinder display only if connected to a Radar
display via hsb2.
E-1
Appendix E: Abbreviations
A
ANSI
AWG
Amp
American National Standards Institute
American Wire Gauge
BDI
Brg
Bearing and Distance Indicator
Bearing
CCFL
CDI
CFR
CMG
COG
CRT
CTR
Cold Cathode Fluorescent Lamp
Course Deviation Indicator
Code of Federal Regulations
Course Made Good
Course Over Ground
Cathode Ray Tube
Center
dB
DC
DMG
DR
deciBels
Direct Current
Distance Made Good
Dead Reckoning
EBL
EMC
ETA
Electronic Bearing Line
Electro Magnetic Compatibility
Estimated Time of Arrival
FCC
FLT
ft
Federal Communication Commission
Float - floating EBL/VRM
feet
FTC
Fast Time Constant
GPS
dGPS
GRD
GHz
Global Positioning System
differential Global Positioning System
Guard Zone
Giga Hertz
HDG
Hz
Heading
High Speed Bus
Hertz
MHz
Mega Hertz
IEEE
in, "
Institute of Electrical & Electronic Engineers
inch
Kg
kW
kilogram
kilo Watt
hsb
2
Appendix E:
Abbreviations
Appendix E: Abbreviations
E-2
hsb2 Plus Series Fishfinders
Appendix E:
Abbreviations
lat
lbs
LCD
lon/long
latitude
pounds
Liquid Crystal Display
longitude
M
m
MARPA
MBS
mm
Magnetic
meters
Mini Automatic Radar Plotting Aid
Main Bang Suppression
millimeter
MOB
MRK
Man OverBoard
Mark
nm
NMEA
nautical mile
National Marine Electronics Association
POS
Position (of vessel)
RC
RF
Rng
rpm
Raychart (chartplotter)
Radio Frequency
Range
Revolutions Per Minute
SHM
SSB
SOG
STC
Ships Heading Marker
Single Side Band
Speed Over Ground
Sensitivity Time Control
T
TFT
TTG
True
Thin Film Transistor
Time To Go
V
VHF
VMG
VRM
Volts
Very High Frequency
Velocity Made Good
Variable Range Marker
WPT
Waypoint
XTE
Cross Track Error
yds
yards
ZMB
Zoom Box
Index
Index
A
Accessories 2-5
Adding
a Waypoint to a Route 5-19, 5-29
Alarm Clock Alarm 6-4
Alarms 4-8
Alarm Clock 6-4
Anchor 6-4
Arrival 5-32, 6-4
Countdown Timer 6-4
Deep Water 4-8
External 4-8, 6-4
Fish Alarm 4-8
Grounding 6-4
MOB 4-13, 6-6
Off Track 6-4
Setting 6-1
Shallow Water 4-8
ALARMS Key 1-19, 4-8, 4-9, 6-4, 6-5
Altering The Current Route 5-30
Anchor Alarm 6-4
Arrival Alarm 5-32, 6-4
A-Scope 1-10, 3-23
Autopilot Pop Up 7-4, 7-8
B
Background Color 3-7
BDI
Window Options 1-7, 3-14
Bearing Mode 7-4, 7-6
Bottom Indications 4-3
Bottom Lock 1-9, 3-21
Bridge NMEA Heading 7-9
Brightness Control 3-7
C
Cable Runs 2-11
Installation Considerations 2-3
Cables
Power 2-11
Transducer 2-11
Cancel MOB 4-13, 6-7
CDI
Window Options 1-7, 3-14
Center the Chart 1-12, 3-28
Chart
Center 1-12
Data 5-2
Nearest 5-7
i
Object Information 5-4, 7-16, 7-18
Port 5-4, 5-5
Source 5-4
Tide 5-4, 5-6
Definition 1-3
Mode 1-6, 1-7
Full Screen 3-9
Moving 3-28
Orientation 7-16, 7-17
Course Up 7-17
Head Up 7-18
North Up 7-17
Scale 3-28, 5-2, 5-20, 6-6
Set Up
Radar/Chart Synch 1-12, 7-16
Simulator 3-5, 7-12
Window Options 1-7, 3-14
Chart Card 1-4, 1-12
Object Information 5-4, 7-16, 7-18
Chart Master 1-3
Chartplotter
Control Functions 3-26
Display Options 1-13
Features 1-12, A-3
Functions 1-15
Set Up 7-2, 7-16
Radar/Chart Synch 7-19
Cleaning
the Display 8-1
the Transducer 8-1
Cleaning Instructions 8-1
CLEAR Key 1-19
Clearing
a Route 5-19
a Track 5-39, 5-40
Clutter 3-19
COG (Course Over Ground) 6-1
Data Box 4-7, 7-4
Vector 7-16, 7-18
Color Bar 7-13
Color Gain 4-5
Color Threshold 3-8
Combined Display
Definition 1-3
Combined Fishfinder/Chartplotter
Switching Control 3-12
Compass Set Up 7-12
Compass Setup 7-5
Connections 2-14
Display Unit 2-15
Transducer 2-15
HSB 2-15, 2-20
NMEA Input 2-15, 2-22, 2-26
NMEA Output 2-15, 2-28, 2-29
Power 2-14
ii
Power & NMEA In 2-15, 2-17, 2-26
SeaTalk 2-15, 2-22, 2-24
Transducer 2-15
Context-sensitive Cursor 1-18, 3-28
Control Functions
Chartplotter 3-26
Conventions Used 3-1
Countdown Timer Alarm 6-4
Course Up 7-17
Creating
a Route 5-19
Creating a Route
from a Track 5-42
Using the Waypoint List 5-21
Cross Track Error - See XTE
Current Route 5-18
Altering 5-30
Cursor 1-16, 1-17
Context-sensitive 1-18, 3-28
Goto 5-30
Readout 7-4, 7-7
Reference 7-4, 7-6
Cursor Data Box 3-15, 3-26
Cursor Echo 6-1, 6-7, 7-5, 7-11
Chart 6-7, 7-11
Local 6-7, 7-11
Radar 6-7, 7-11
Custom Options - Chart 3-27
Customizing
the Chart Display 7-16
the Screen Presentation Options 3-26
D
Data
HSB 6-1
hsb2 6-1
Data Box 3-15, 3-26, 4-7, 7-4, 7-6
COG 4-7, 7-4
Cross Track Error 7-4
Cursor 3-26
Date 7-4
Depth 4-7, 7-4
Group of Six 3-15, 3-26
On/Off 3-27
Heading 7-4
List of 7-4
Log/Trip 7-4
MOB 4-13, 6-6
Moving 3-27
Pilot 7-4
Position 4-7, 7-4
Ruler 6-2, 6-3
SOG 4-7, 7-4
Speed 4-7, 7-4
Temperature 4-7, 7-4
hsb2 Plus Series Fishfinders
Tide Set/Drift 7-4
Time 7-4
VMG 7-4
Waypoint 4-7, 7-4
Wind 7-4
Data Display 5-26
Chart Object 5-4
Nearest 5-7
Port 5-4, 5-5
Source 5-4
Tide 5-4, 5-6
Fishfinder 4-7
Route 5-19
Data from other Equipment 2-28, 4-13, 6-1, 6-6
COG 6-1
Heading 4-13, 6-1, 6-6
NMEA 6-1
Position 4-13, 6-1, 6-6
Radar 6-1
SeaTalk 6-1
Speed 4-13, 6-6
Data Log Mode 1-7, 6-1, 6-10
Full Screen 3-10
Database List 1-16, 1-21
Route 5-15, 5-19, 5-22, 5-26
Track 5-41
Waypoint 4-11, 4-12, 5-8, 5-9, 5-20, 5-33
Date Data Box 7-4
Date Format 7-5, 7-11
Datum Selection 7-16, 7-19
Day/Night 7-4, 7-7
Dedicated Keys 1-4, 1-16, 1-19
ALARMS 4-8, 4-9, 6-4, 6-5
CLEAR 1-19
DISPLAY 1-6, 3-9, 3-10, 3-12, 4-7, 6-10
GAIN 4-4, 4-6
MARKS 4-11, 4-13, 5-9, 5-12, 5-36, 5-37,
6-6
MENU 3-5, 5-39, 6-9, 7-1, 7-2
MULTI 3-6, 3-7, 3-8, 3-9, 3-17
POWER 3-2, 3-5
RANGE 3-17, 3-30, 5-2
VRM/EBL 4-9, 6-1, 6-3
Deep Water Alarm 4-8
Deleting - See Erasing 5-15
Depth
Determining Using VRM 4-9
Digit Size 7-13, 7-14
Offset 7-13, 7-14
Depth Data Box 4-7, 7-4
Depth Range 7-13, 7-15
Display
Brightness 3-7
Cleaning 8-1
Features 1-5
Lighting 3-6, 3-7
Index
Operating Modes 1-6
Selecting 3-9
DISPLAY Key 1-6, 1-19, 3-9, 3-10, 3-12, 4-7,
6-10
Display Options
Chartplotter 1-13
Display Unit 1-4
Background Color 3-7
Connections 2-15
Console Mounting 2-13
Grounding 2-14
Location 2-7
Mounting 2-12
Specification A-1
Switching Off 3-4, 3-5
Displaying
Chart Data 5-3
Waypoint Data 5-9, 5-13, 5-26
Distance
Determining Using VRM 4-9
E
Echoes - Fishfinder 1-8, 3-6
Color Threshold 3-8
Strength 4-1
Editing
a Route 5-19, 5-28
Using the ST80 Navigator Keypad 5-18
a Waypoint 5-9
Waypoint Details 5-13
Using the ST80 Navigator Keypad 5-18
EMC
Conformance 2-18
Installation Guidelines 2-3
Servicing and Safety Guidelines 8-2
ENTER Key 1-19
Erasing
a Route 5-19
a Waypoint 5-9, 5-15
External Alarms 4-8, 6-4
F
Factory Reset 8-3
Features
Chartplotter 1-12, A-3
Display 1-5
Fishfinder 1-8, A-3
Find Ship 3-28
Fish Alarm 4-8
Fish Indications 4-2
Fishfinder
Data Display 4-7
Definition 1-3
Display Options 1-9
iii
A-Scope 1-10, 3-23
Bottom Lock 3-21
White Line 4-2, 4-4
Zoom 1-10, 3-24
Echoes 1-8, 3-6
Features 1-8, A-3
Functions 1-10
HSB Mode 7-13, 7-14
Mode 1-7
Full Screen 1-6, 3-10
Set Up 7-2, 7-13
Simulator 3-1, 3-5, 7-13, 7-15
Window Options 1-7, 3-14
Fishfinder Controls
Color Gain 4-5
Gain 4-4
Range 3-17
Scroll Speed 3-15
STC 4-6
Fishfinder Image
Adjusting 4-1
Interpreting 4-1
Bottom Indications 4-3
Fish Indications 4-2
Fishfinder Master 1-3
Fishfinder Repeater 1-3
Fishfinder System 1-4
Follow
a Route 5-30
Stop 5-30
Frequency 1-9, 4-3
Fishfinder Transducer 3-20
Split Frequency 3-20
Functions
Chartplotter 1-15
Fishfinder 1-10
G
Gain - Fishfinder 4-4
GAIN Key 1-19, 4-4, 4-6
Goto
a Target 5-30
a Waypoint 5-30
Cursor 5-30
Stop 5-30
GPS
Set Up 6-1, 6-9
GPS SOG/COG Filter 7-5, 7-11
H
Half Screen Windows 1-6, 3-10
Selecting 3-12
Head Up 7-18
Heading 4-13, 6-6, 7-9
iv
Data 6-1
Heading Data Box 7-4
Heading Vector 7-16, 7-18
Help 7-4, 7-7
Help from Raymarine 8-5
High Voltage iii
HSB
Connection 2-15
Data 6-1
HSB Mode - Fishfinder 7-13, 7-14
hsb2 1-3
Connection 2-20
Data 6-1
I
In-hull Transducer 1-4
Installation
Cable Runs 2-3, 2-11
EMC Conformance 2-18
EMC Guidelines 2-5
Integrated System 2-18
Location 2-3, 2-7
Installation Guidelines
EMC 2-3
Integrated System 1-5, 5-19
Definition 1-3
Diagram 2-20, 2-24
Installation 2-18
Installation Checks 2-29
Switching Control Between Fishfinder, Radar,
and Chart 3-12
Intended Use iii
J
Junction Box
for External Instruments 2-26
K
Key Beep 7-4, 7-7
Keys
Dedicated 1-4, 1-16
Dedicated Keys 1-19
Lighting 3-6, 3-7
Soft 1-4, 1-16, 1-19, 7-4, 7-7
L
Language 7-6, 7-12
Lighting Control
Display 3-6, 3-7
hsb2 Plus Series Fishfinders
Key 3-6, 3-7
Local Cursor Echo 6-7, 7-11
Location
Display Unit 2-7
Log/Trip Data Box 7-4
Loran TDs 5-10
M
Maintenance 8-1
Make and Follow a Route Scenario 5-46
Man Overboard (MOB) - See MOB
Managing Tracks 5-39
Marks 5-8
MARKS Key 1-19, 4-11, 4-13, 5-9, 5-12, 5-36,
5-37, 6-6
Master Display 1-5, 2-19, 5-2
Definition 1-3
Measuring Distances Using the VRM/EBL Key 6-1
MENU Key 1-19, 3-5, 5-39, 6-9, 7-1, 7-2
Menu Timeout 7-4, 7-8
MOB 4-13, 6-1
Alarm 4-13, 6-6
Cancel 4-13, 6-7
Data Box 4-13, 6-6
Data Selection 7-4, 7-8
Symbol 4-13, 6-6
Waypoint 4-13, 6-6
Modes 1-6
Chart 1-6, 1-7, 3-9
Data Log 1-7, 3-10, 6-1, 6-10
Fishfinder 1-7
Full Screen 3-9
Radar 1-7
Mounting the Display Unit 2-12
Console Mounting 2-13
Moving
a Waypoint 5-9, 5-15, 5-19
Around the Chart 5-20
Databoxes 3-27
the Cursor 1-17
MULTI Key 1-19, 3-6, 3-7, 3-8, 3-9, 3-17
N
Name
a Route 5-19, 5-22
Using the ST80 Navigator Keypad 5-18
a Waypoint 5-9, 5-13, 5-14
Using the ST80 Navigator Keypad 5-18
Nav Data
Window Options 1-7, 3-14
Navigation Aid iii
Index
NMEA 1-5, 2-25
Data 2-25, 6-1
Heading 7-9
Input Connection 2-15, 2-22, 2-26
Output Connection 2-15, 2-28, 2-29
Output Set Up 7-5, 7-9
North Up 7-17
O
Object Information - Chart 7-16, 7-18
Displaying 5-4
Off Track Alarm 6-4
Offsetting the Center 1-12
Operating Controls
Cursor 1-16, 1-17
Database List 1-16, 1-21
Dedicated Keys 1-4, 1-16, 1-19
Pop-up Menus 1-16, 1-20
Soft Keys 1-4, 1-16, 1-19, 7-4, 7-7
Trackpad 1-4, 1-16, 1-17, 3-28
Operating Modes 1-6
Chart 3-9
Data Log 3-10, 6-1, 6-10
Fishfinder 3-10
Plotter 3-31, 7-17
Selecting 3-9
Orientation - Chart 7-17
P
Palette 7-16, 7-18
Picture Reset 8-3
Pilot Data Box 7-4
Place and Goto a Waypoint Scenario 5-44
Placing
a Waypoint 4-11, 5-9, 5-20
Plotter Mode 3-31, 7-16, 7-17
Pop-up Menus 1-16, 1-20
Port Data 5-4, 5-5
Position 4-13, 6-1, 6-6
a Waypoint 5-9, 5-13
Position Data Box 4-7, 7-4
Position Offset 7-16, 7-19
Power
Cable 2-11
Connection 2-14
for External Equipment 2-14, 2-18
Power & NMEA In
Connection 2-15
Power & NMEA Input
Connection 2-15, 2-17, 2-26
POWER Key 1-19, 3-2, 3-4, 3-5
Power Setting 3-17
Power-on Reset 8-3
Power-on Sequence 3-2, 3-4
v
Chart Mode 3-4
R
Radar
Set Up
Radar/Chart Synch 1-12
Simulator 3-5
Typical System Diagram 2-1
Window Options 1-7, 3-14
Radar Display
Definition 1-3
Radar Master 1-3
Radar Mode 1-7
Radar Overlay 6-1, 6-7
Radar Repeater 1-3
Radar/Chart Synch 1-12, 7-16
Radar/Chart Synchronization 7-19
Range
Fishfinder 3-17
RANGE Key 1-19, 3-17, 3-30, 5-2
Raystar 120 WAAS GPS Receiver B-6
Remote Cursor Echo
Chart 6-7, 7-11
Radar 6-7, 7-11
Removing
a Waypoint from a Route 5-19, 5-29
Repeater Display 1-5, 2-19, 5-2, 5-19
Definition 1-3
Restart
XTE 5-30, 5-33
Retrieving
a Route 5-19
Returning to the Full-Screen Display 3-13
Review Your Passage Plan Scenario 5-48
Route
Clearing 5-19
Creating 5-19
Creating from a Track 5-42
Current 5-18
Data Display 5-19
Database List 5-15, 5-19, 5-22, 5-26
Editing 5-19, 5-28
Using the ST80 Navigator Keypad 5-18
Erasing 5-19
Follow 5-30
Naming 5-19, 5-22
NMEA Transfer 5-35
Retrieving 5-19
Saving 5-19
Transfer 5-19
Route Leg 5-18
Data Display 5-25
Routine Checks 8-1
Ruler Data Box 6-2, 6-3
vi
S
Safety iii, 5-1
EMC Guidelines 2-5
High Voltage iii
Navigation Aid iii
Saving
a Route 5-19
Scale
Chart 3-28, 5-2, 5-20, 6-6
Scenarios
Make & Follow a Route 5-46
Place & Goto a Waypoint 5-44
Review Your Passage Plan 5-48
Scroll Speed - Fishfinder 3-15
Scrolling Bottom Graph 1-8
SeaTalk 1-5, 2-24
Connection 2-15, 2-22, 2-24
Data 2-24, 6-1, 6-7, 7-11
Selecting
a Half Screen Window 3-12
a Waypoint 5-9
the Operating Mode 3-9
Sensitivity - See Gain 4-4
Servicing
EMC Guidelines 8-2
Setting Alarms and Timers 6-1
Setting Up
a GPS 6-1, 6-9
Chart Parameters 7-2, 7-16
Custom Options 3-27
Fishfinder Parameters 7-2, 7-13
System Parameters 7-2
Tracks 5-39, 5-40
Shallow Water Alarm 4-8
Simulator 7-6, 7-12
Chart 3-1, 3-5
Fishfinder 3-1, 3-5, 7-13, 7-15
Simulator Mode 3-5
SmartRoute 5-42
Soft Key Labels 7-7
Soft Keys 1-4, 1-16, 1-19, 7-4, 7-7
SOG (Speed Over Ground) Data Box 4-7, 7-4
Sonar - See also Fishfinder
HSB Mode 7-13, 7-14
Sonar History 7-13, 7-14
Sonar Simulator 7-15
Speed 4-13, 6-6
Calibration 7-13, 7-14
Data Box 4-7, 7-4
Fishfinder Scroll 3-15
Split Frequency 3-20
ST80 Navigator Keypad 5-16
Status Bar 1-8, 1-12
STC 4-6
hsb2 Plus Series Fishfinders
Stop
Follow 5-30
Goto 5-30
Track - See Clear Track
Surface Clutter 3-19
Switching
Databoxes On/Off 3-27
Range Rings On and Off 3-26
the Chart On 3-4
the Cursor Data Box On and Off 3-26
the Display On and Off 3-5
Symbol
MOB 4-13, 6-6
Waypoint 5-8, 5-13, 7-16, 7-18
Synchronize Chart and Radar 7-16
System
Connections 2-14
Grounding 2-14
Set Up 7-2
T
Target (Chart) 5-30
Arrival 5-30
Goto 5-30
Waypoint 5-30
Target Depth ID 7-13
Temperature Calibration 7-13, 7-14
Temperature Data Box 4-7, 7-4
Terminology 1-3
Thru-hull Transducer 1-4
Tide Data 5-4, 5-6
Tide Set/Drift Data Box 7-4
Tide Vector 7-16, 7-18
Time Data Box 7-4
Time Format 7-5
Time Offset 7-5
Timers
Alarm Clock 6-4
Countdown 6-4
Setting 6-1
Trackpad 1-4, 1-16, 1-17, 3-28
Tracks
Clearing 5-39, 5-40
Converting to Route 5-42
Database List 5-41
Managing 5-39, 5-40
Naming
Using the ST80 Navigator Keypad 5-18
Setting Up 5-39
Transducer 1-4
Cable 2-11
Cleaning 8-1
Connections 2-15
Frequency 3-20, 4-3
Index
In-hull 1-4
Thru-hull 1-4
Transom Mount 1-4
Transfer
Route 5-19
Transom Mount Transducer 1-4
vii
Half Screen 1-6, 3-10
Nav Data 1-7, 3-14
Radar 1-7, 3-14
World Map 1-12, 5-2
X
Units 7-4, 7-8
XTE (Cross Track Error)
Data Box 7-4
Restart 5-30, 5-33
V
Z
Variation Source 7-5, 7-8
Vectors 7-16, 7-18
VMG Data Box 7-4
VRM/EBL Key 1-19, 4-9, 6-1, 6-3
Zoom 1-10, 1-12, 3-24
U
W
WAAS 1-1, B-6
Warranty v
Waypoint 6-6, 7-16, 7-18
Adding to a Route 5-19, 5-29
Data Box 4-7, 7-4
Data Display 5-8, 5-9, 5-13, 5-26
Database List 4-11, 4-12, 5-8, 5-9, 5-20, 5-33
Editing 5-9
Using the ST80 Navigator Keypad 5-18
Editing Details 5-13
Erasing 5-9, 5-15
Goto 5-30
List 5-13, 5-15
Moving 5-9, 5-15, 5-19
Naming 5-9, 5-13, 5-14
Numbers 7-16, 7-18
Placing 4-11, 5-8, 5-9, 5-20
Position 5-9, 5-13
Removing from a Route 5-19, 5-29
Selecting 5-9
Symbol 5-8, 5-9, 5-13, 7-16, 7-18
Target 5-30
Transfer 5-8, 5-18
Transferring on NMEA 5-35
Transferring on SeaTalk 5-35
Waypoint List
Creating a Route 5-21
White Line 4-2, 4-4
Wind Data Box 7-4
Window Options
BDI 1-7, 3-14
CDI 1-7, 3-14
Chart 1-7, 3-14
Fishfinder 1-7, 3-14
Full Screen 1-6
viii
hsb2 Plus Series Fishfinders
">