Movincool | Classic 18 | Specifications | Movincool Classic 18 Specifications

Movincool Classic 18 Specifications
OPERATION MANUAL
CLASSIC 10 and CLASSIC 18
Unit Serial Number Range: 1111XXXX### to Present
(From November 2011 to Present)
READ THIS MANUAL CAREFULLY FOR INSTRUCTIONS ON CORRECT
INSTALLATION AND USAGE, AND READ ALL SAFEGUARDS
SECCIÓN EN ESPAÑOL
SECTION EN FRANÇAIS
AVAILABLE AT WWW.MOVINCOOL.COM
SERIAL NUMBER LOCATION AND IDENTIFICATION
Nameplate Label
COOLING AMPS. WITH PUMP
COMPR. OUTPUT
REFRIGERANT/TOTAL CHARGE
DESIGN PRESSURE LO/HI
PART NO./WEIGHT
SERIAL NO.
Nameplate Label Position
Month
Year
Model
Sequential
Number
© 2013 DENSO PRODUCTS AND SERVICES AMERICAS, INC.
All rights reserved. This book may not be reproduced or copied, in
whole or in part, without the written permission of the publisher.
DENSO PRODUCTS AND SERVICES AMERICAS, INC. reserves the
right to make changes without prior notice. MovinCool®, Office Pro®,
and SpotCool® are registered trademarks of DENSO Corporation.
OPERATION MANUAL
CLASSIC 10 and CLASSIC 18
Table of Contents
SERIAL NUMBER LOCATION AND IDENTIFICATION ................................... 2
FOREWORD ...................................................................................................... 5
Definition of Terms................................................................................ 5
GENERAL WARNINGS & CAUTIONS.............................................................. 6
INVENTORY & ASSEMBLY .............................................................................. 7
Inventory ................................................................................................ 7
Assembly ............................................................................................... 8
INSTALLATION ................................................................................................. 9
Choosing an Installation Site ............................................................... 9
Moving the Unit ................................................................................... 10
Plugging in the Unit............................................................................. 11
Warning Signal Connection................................................................ 12
Fire Alarm Control Panel Connection................................................ 13
LCDI Power Cord Instruction ............................................................. 14
FEATURES ...................................................................................................... 15
OPERATION .................................................................................................... 16
Control Panel ....................................................................................... 16
LED Display Descriptions................................................................... 17
Operating in COOL Mode.................................................................... 18
Operating in FAN ONLY Mode............................................................ 19
Changing from FAN ONLY Mode to COOL Mode ............................. 19
Operating Modes ................................................................................. 20
Self-Diagnostic Codes ........................................................................ 21
Empty the Drain Tank ......................................................................... 22
Condensate Pump Kit (Optional for Classic 10)............................... 23
Condensate Pump Kit (Optional for Classic 18)............................... 24
INSPECTION & MAINTENANCE..................................................................... 25
Empty the Drain Tank ......................................................................... 25
Clean the Air Filters ............................................................................ 25
Filter Removal Method ........................................................................ 25
Filter Element Cleaning Method......................................................... 25
In-Season/Off-Season Inspection & Maintenance............................ 26
TROUBLESHOOTING ..................................................................................... 27
TECHNICAL SPECIFICATIONS OF CLASSIC 10 .......................................... 28
TECHNICAL SPECIFICATIONS OF CLASSIC 18 .......................................... 29
FOREWORD
Congratulations on purchasing the MovinCool portable air conditioner. This
manual explains how to install and operate the MovinCool Classic 10, and Classic
18 portable air conditioning units. Please read this operation manual thoroughly to
familiarize yourself with the features of the unit and to ensure years of reliable
operation.
You may also find it useful to keep this operation manual on hand for reference.
Components and/or procedures are subject to change without prior notice.
Definition of Terms
WARNING: Describes precautions that should be observed in order to
prevent injury to the user during installation or unit operation.
CAUTION: Describes precautions that should be observed in order to
prevent damage to the unit or its components, which may occur during
installation or unit operation if sufficient care is not taken.
Note: Provides additional information that facilitates installation or unit operation.
5
GENERAL WARNINGS & CAUTIONS
1. All electrical work, if necessary, should only be performed by qualified
electrical personnel. Repair to electrical components by non-certified
technicians may result in personal injury and/or damage to the unit. All
electrical components replaced must be genuine MovinCool parts, purchased
from an authorized reseller.
2. The proper electrical outlet for MovinCool units must be equipped with a UL
recognized circuit breaker and ground fault protective breaker.
3. Because of potential safety hazards under a certain condition, we strongly
recommend against the use of an extension cord.
However, if you still elect to use an extension cord, it is absolutely necessary
that it is a UL listed, 3-wire grounding type appliance extension cord, having a
3-blade and a 3-slot receptacle that plugs into the appliance.
The marked rating of the extension cord should be 115 V, 15 A for Classic 10,
and 208/230 V, 15 A for Classic 18 or equivalent.
4. The Classic 10 is equipped with a 10 feet (3.0 m) UL recognized LCDI power
cord. The Classic 18 is equipped with a 6 feet (1.8 m) UL recognized LCDI
power cord. For replacement, fixed location (hardwire) or power cord
lengthening (extension cord) cords are required, contact your MovinCool
reseller or a qualified electrician for approved replacement methods.
5. Never fold or place heavy objects on the power cord.
This could result in damage to the power cord causing electrical shock or fire.
6. Do not place water or any other liquid on the unit. This can cause damage to
the unit and increase the risk of electrical shock.
7. Do not sit or stand on the unit.
6
INVENTORY & ASSEMBLY
Inventory
After unpacking your MovinCool unit, please check to make sure you have the
following items:
1. Classic 10 or Classic 18 MovinCool Unit (1)
2. Cool Air Outlet Duct(s) (Classic 10 qty. = 1, Classic 18 qty. = 2)
3. Screws (Classic 10 qty. = 4, Classic 18 qty. = 8)
4. Operation Manual/Product Registration (1)
Note: If any of these items were not included in the box or appear damaged,
please contact your MovinCool reseller for replacement.
COOL AIR
OUTLET DUCT(S)
SCREWS
MOVINCOOL UNIT
OPERATION MANUAL /
PRODUCT REGISTRATION
7
INVENTORY & ASSEMBLY (cont.)
Assembly
CAUTION: Before assembling make sure the unit is on a flat, level
surface and the casters are in the LOCKED position.
(Both the Classic 10 and Classic 18 MovinCool units have locking
swivel casters in the front only.)
UNLOCKED
LOCKED
Install each cool air outlet duct using 4 screws each as shown.
Note: Do not over tighten the screws when installing the cool air outlet ducts. This
could damage the base on the cool air outlet duct assembly.
COOL AIR OUTLET DUCT
SCREW (4 PER DUCT)
8
INSTALLATION
Choosing an Installation Site
CAUTION: Following are some precautions to consider before
choosing your installation site. Please review carefully as improper
installation may result in personal injury or damage to the unit.
1. Do not use the unit in areas where leakage of flammable gas may occur.
2. Do not use the unit in areas where it is exposed to rain or water.
3. Do not use the unit in an atmosphere of excessively corrosive gas or vapor.
4. Do not use in areas where the temperature is outside the allowable operating
range.
5. Do not install the unit in sloping areas. The unit may move or topple over even
if the casters are set to the LOCKED position.
6. Install the unit in areas that can with-stand the weight of the unit. The Classic
10 unit weighs approximately 190 lb (86 kg), and the Classic 18 unit weighs
approximately 199 lb (90 kg) when the drain tank is full of water.
7. Allow 18.0 inch (457 mm) of unobstructed airflow for both the air inlets and
outlets.
8. Do not use the unit at condition above 104 °F (40 °C) 50 %RH.
9
INSTALLATION (cont.)
Moving the Unit
Unlock the casters and push the MovinCool unit to a flat level surface and set the
casters back to the LOCKED position.
UNLOCKED
LOCKED
10
INSTALLATION (cont.)
Plugging in the Unit
1. Check the prongs and surface of the power cord plug for dust/dirt. If dust and/
or dirt are present, wipe off with a clean, dry cloth.
2. Check the power cord, plug and prongs for damage or excess play. If any
damage or excess play is found, contact your MovinCool reseller or a qualified
technician for repair.
WARNING:
1. If the power cord or plug is damaged, repair should only be
performed by qualified electrical personnel.
2. Do not connect/disconnect the power cord or attempt to operate
buttons with wet hands. This could result in electrical shock.
3. Because of potential safety hazards under a certain condition, we
strongly recommend against the use of an extension cord.
However, if you still elect to use an extension cord, it is absolutely
necessary that it is a UL listed, 3-wire grounding type appliance
extension cord, having a 3-blade and a 3-slot receptacle that plugs
into the appliance. The marked rating of the extension cord should
be 115 V, 15 A for Classic 10 and 208/230 V, 15 A for Classic 18.
CAUTION: The power source should be a dedicated single outlet
circuit with UL recognized short-circuit and ground fault protective
breaker. Do not share the outlet with any other instrument or
equipment. The minimum power supply rating and the maximum
fuse size is shown below.
MODEL
MINIMUM POWER SUPPLY RATING
RECOMMENDED
FUSE SIZE
Classic 10
115 V, single phase, 60 Hz
15 A maximum
Classic 18
208/230 V, single phase, 60 Hz
15 A maximum
Note:
1. Make sure the AC outlet is free of dirt, dust, oil, water, or any other foreign
matter.
2. The Classic 10 is equipped with a UL recognized LCDI cord and NEMA plug
configuration (5-15). The appropriate outlet must be used for this plug type.
3. The Classic 18 is equipped with a UL recognized LCDI cord and NEMA plug
configuration (6-15). The appropriate outlet must be used for this plug type.
11
INSTALLATION (cont.)
Warning Signal Connection
(Output Signal Terminal L+ and L-)
The controller is equipped with a warning signal output relay type (Form C, normal
open dry contact) which can be used to monitor the failure condition.
Relay contactor is closed when the following condition has occurred:
a. Tank full
b. Temperature sensor fails
The relay output contactor is rated 2 A at 30 VDC or 2 A at 30 VAC (resistive load)
and it is compatible with various warning devices such as alarm speaker, light
indicators, and etc.
Connecting Warning Signal From Controller
1. Remove service panel from the rear of the unit.
2. Squeeze the inner latches and push out the black cap from inside the panel.
Cap
Latch
3. Use recommended warning signal wire size from 16 AWG to 26 AWG for a
solid wire, or 16 AWG to 22 AWG for a stranded wire with ring terminal for #6
stud size.
4. Connect the warning device to terminal L+ and L- according to its polarities.
UNIT TERMINAL
WARNING DEVICE
E+
EL+
LRELAY OUTPUT CONTACTOR
12
INPUT SIGNAL
INSTALLATION (cont.)
Fire Alarm Control Panel Connection
(Input Signal Terminal E+ and E-)
The controller is equipped with a normal open input signal, which can be
connected directly from the fire alarm control panel. This input signal terminal
should only be connected to a close or open dry contact signal. When receiving
the signal from the fire alarm control panel, the unit turns off and does not turn back
on until it has been RESET.
Connecting Fire Alarm Control Panel to Controller
1. Remove service panel from the rear of the unit.
2. Squeeze the inner latches and push out the black cap from inside the panel.
Cap
Latch
3. Use recommended warning signal wire size from 16 AWG to 26 AWG for a
solid wire, or 16 AWG to 22 AWG for a stranded wire with ring terminal for #6
stud size.
4. Connect the fire alarm device to terminal E+ and E- according to its polarities.
UNIT TERMINAL
FIRE ALARM DEVICE
OUTPUT SIGNAL
E+
EL+
L-
OPEN DRY CONTACT
13
INSTALLATION (cont.)
LCDI Power Cord Instruction
WARNING
The LCDI device is a non-serviceable device.
Attempting to open the device may expose the user to the hazards of electric shock, and
could void warranties of this product.
Manufacturer’s liability is limited to the replacement of the device.
CAUTION
1.
2.
3.
4.
5.
6.
7.
8.
Read the attention printed on the device for proper use and handling of this device.
This device is used for monitoring leakage current.
Do not immerse in water.
This device must only be plugged into an appropriate wall outlet. Do not use on
extension cords or adapter. Do not remove ground prong.
In the event that this device trips, the cause of malfunction should be corrected first
before further use.
Using the device beyond recommended voltage poses risk to users.
Conductors inside this cord are surrounded by shields, which monitor leakage
current. These shields are not grounded, and the cords are periodically examined for
any damage. Do not use this product in the event the shields become exposed.
Do not push TEST and/or RESET buttons in a short period.
Procedure
Test device once when AC is installed to assure proper operation.
1. Plug into grounded power receptacle.
2. If light is not on, press RESET button once. Light should turn on.
3. Press TEST button once, light must turn off.
4. Press RESET button once again for use. Light should turn on.
5. If test fails, do not use.
<FRONT VIEW>
TYPE 2
TYPE 1
TEST Button
TEST Button
RESET Button
RESET Button
14
FEATURES
1. A digital electronic control panel, which allows the user to easily control the
unit’s operation.
2. Digital LED display that indicates:
a. Room temperature and set point temperature
(either Fahrenheit or Celsius)
b. Status codes
3. The set point temperature can be adjusted between 70 °F (21 °C) and 95 °F
(35 °C) by the SET TEMP buttons ( / ).
4. Fire alarm control panel connection with automatic shut off.
5. Automatic shut off, warning signal output and alarm for temperature sensor
failure and tank full.
6. A condensate drain “FL” is displayed by the LED.
7. An automatic restart feature when the power is lost and regained. The unit
returns to the operating mode it was in prior to the loss of power.
15
OPERATION
Control Panel
Before operating the unit, it is important to familiarize yourself with the basic
controls located on the control panel.
1. COOL ON/OFF Button
Activates COOL mode or turns the unit off.
2. FAN Button
Activates FAN ONLY mode or turns the unit
off.
3. SET TEMP Buttons (
/
)
Increases or decreases the temperature
set point during COOL mode.
4. Room Temperature/
Set Point Display
Displays a flashing set point temperature
for 5 seconds, and then continuously
indicates the room temperature.
5. Temperature Scale LED
Lit to indicate the current temperature being
displayed in either °F or °C.
6. ON LED
Turns on during FAN ONLY mode and
during COOL mode with Fan Operate
mode.
7. AUTO LED
Turns on during COOL mode with FAN
STOP mode.
16
OPERATION (cont.)
Control Panel (cont.)
LED Display Descriptions
In normal operation, the LED displays the following descriptions.
Display
Descriptions
Conditions
Right decimal point is on.
Standby or FAN ONLY
mode.
Indicates room temperature when display is lit.
(Left fig. : Room temperature at 78 °F)
During COOL mode.
Indicates set point temperature when display
is flashing for 5 seconds.
(Left fig. : Set point temperature at 75 °F)
During set point
temperature
adjustment.
Note: The ROOM TEMP display range is from 0 °F (-9 °C) to 109 °F (60 °C). When
the display value is greater than 99 °F, it displays values of 00 for 100 °F, 01 for
101 °F, and 09 for 109 °F. (This only applies to Fahrenheit values.)
17
OPERATION (cont.)
Operating in COOL Mode
1. The unit can be operated in COOL mode by pressing the COOL ON/OFF
button.
Note: In COOL mode the unit can only be turned off by pressing the COOL
ON/OFF button.
2. Change the temperature set point by pressing the SET TEMP buttons (
Note: When turning the unit on, the set point and operation mode are
determined by the last operating mode.
18
/
).
OPERATION (cont.)
Operating in FAN ONLY Mode
1. The unit can also be operated in FAN ONLY mode by pressing FAN button.
2. The unit can only be turned off by pressing the FAN button again.
Changing from FAN ONLY Mode to COOL Mode
The COOL mode can be activated while the unit is operating in FAN ONLY mode.
To do this, simply press the COOL ON/OFF button.
Note: The FAN ONLY mode does not operate after the COOL mode has been
activated. The unit can only be turned off by pressing the COOL ON/OFF button.
19
OPERATION (cont.)
Operating Modes
The Classic 10 and Classic 18 can be operated in two modes, FAN ONLY and
COOL. When in FAN ONLY mode, the unit circulates the surrounding air. When in
COOL mode, the compressor is operated and cool air is circulated.
1. COOL Mode
Once the compressor has been disengaged for more than 120 seconds, the
unit operates in FAN ONLY mode for approximately 5 seconds before the
compressor re-engages (see page 28).
2. Temperature Control
The room temperature thermistor monitors the inlet temperature versus set
point temperature and switches the unit automatically between COOL and
FAN ONLY modes.
3. Fan Mode Control DIP Switch
The fan mode control DIP switch determines whether the fan continues to
operate or stop when the compressor cycles off. (Set point temperature below
the inlet air or room temperature.) The unit has been preset at the factory for
continuous fan operation.
Note: If you want to change the fan mode operation (from OPERATE to
STOP), contact your MovinCool reseller.
4. Temperature Scale Display
The temperature scale display changes the temperature(s) that are displayed
to either °C or °F. The unit has been preset from the factory to display the
temperature(s) in °F.
Note: If you want to change the temperature scale display (from °F to °C), hold
down the SET TEMP buttons ( / ) and the FAN button simultaneously for
3 seconds.
20
OPERATION (cont.)
Self-Diagnostic Codes
Self-diagnostic codes are displayed on the control board under the following
conditions.
LED Display Codes
Condition
When the drain tank switch is activated, the LED displays
“FL” and the unit turns off automatically. Once emptying
the drain tank procedure is completed and ON/OFF has
been pressed, unit returns to normal operation.
When the condensate pump malfunctions, the
compressor shuts off, and the LED displays “AS”. Once
condensate pump is fixed and unit has been RESET, the
unit returns to normal operation.
To RESET: Hold down the SET TEMP ( / ) buttons
simultaneously for 3 seconds.
< Classic 10 ONLY > When high pressure switch is
activated 3 times in 24 hours, the unit displays blinking
“HP”. If the high pressure switch is activated 10 times in
24 hours, “HP” turns on. The unit returns to normal
operation after the problem is fixed and the controller is
RESET.
To RESET: Hold down the SET TEMP ( / ) buttons
simultaneously for 3 seconds.
When room thermistor becomes open or shorted, display
shows “E1” and cool mode operation is off. Display and
cool mode operation are returned to normal operation
after room thermistor is fixed.
When freeze thermistor becomes open or shorted,
display shows “E2” and cool mode operation is off.
Display and cool mode operation are returned to normal
operation after freeze thermistor is fixed.
When the unit detects a signal from the fire alarm
system, the display shows "AL" and a buzzer turns on.
Check the fire alarm system and confirm that there is no
signal input to the unit. The unit returns to the normal
operation after the problem is fixed and the controller is
RESET.
To RESET: Hold down the SET TEMP ( / ) buttons
simultaneously for 3 seconds.
Contact your MovinCool reseller or a qualified technician if problem persists.
21
OPERATION (cont.)
Empty the Drain Tank
During COOL mode, condensate water accumulates in the drain tank.
When the drain tank becomes full, the LED displays “FL” and the unit turns off
automatically.
Note: If you want to empty the drain tank, while the unit is in operation, press the
COOL ON/OFF button to turn the unit off.
1. Pull the drain tank from the unit.
2. Remove the cap and empty the drain
tank.
CAP
3. Replace the cap and return the drain tank to the unit.
4. Press the COOL ON/OFF button to restart the unit.
22
OPERATION (cont.)
Condensate Pump Kit (Optional for Classic 10)
A condensate pump kit is available to allow continuous operation and to eliminate
the need for a drain tank.
When the water collects to level (A) in the
pump reservoir, the condensate pump
begins to operate and discharge the water.
Note: The compressor does not operate while the condensate pump is
discharging the water.
When the water level drops below level (B), the condensate pump stops, and the
compressor restarts.
Note: If for any reason the water level exceeds that of level (A) in the pump
reservoir, an over flow drain switch stops the compressor operation, and the LED
displays “AS”.
Note: If the fan mode control DIP switch (see page 20) is set to the STOP position,
the entire unit (including fan operation) turns off either due to the over flow drain
switch or while the condensate pump is discharging the water.
CONDENSATE PUMP
CONDENSATE
PUMP
RESERVOIR
DISCHARGE HOSE
23
OPERATION (cont.)
Condensate Pump Kit (Optional for Classic 18)
A condensate pump kit is available to allow continuous operation and to eliminate
the need for a drain tank.
When the water collects to level (A) in the
pump reservoir, the condensate pump
begins to operate and discharge the water.
When the water level drops below level
(B), the condensate pump stops.
Note: If for any reason the water level
exceeds that of level (A) in the pump reservoir, an overflow drain switch stops the
compressor operation, and the LED displays “AS”.
Note: If the fan mode control DIP switch (see page 20) is set to the STOP position,
the entire unit (including fan operation) turns off due to the over flow drain switch.
CONDENSATE PUMP
CONDENSATE
PUMP
RESERVOIR
DISCHARGE HOSE
24
INSPECTION & MAINTENANCE
Empty the Drain Tank
To empty the drain tank, refer to instructions on page 22.
Clean the Air Filters
Clean the air filters once a week. If the unit is used in a dusty environment, more
frequent cleaning may be required.
A dirty air filter can reduce air output resulting in a decrease in cooling capacity.
Filter Removal Method
1. Turn the unit off, by pressing the COOL ON/
OFF button.
2. Remove the air filters.
Note: To remove the side air filters, lift
upward, then pull outward from the bottom. To
remove the front panel air filter, pull out top
corners, then lift upward.
3. Remove the element from each filter.
FILTER
Filter Element Cleaning Method
1. Remove dust from the element with a vacuum
cleaner, or rinse in cold or lukewarm water. If
the element is extremely dirty, wash with a
neutral detergent.
2. After the element has been cleaned, rinse
with clean running water, allow to dry, then
reinstall.
25
FILTER
INSPECTION & MAINTENANCE (cont.)
In-Season/Off-Season Inspection & Maintenance
In-Season
1. Check the prongs and surface of the power cord plug for dust and/or dirt. If
dust and/or dirt are present, wipe off with a clean dry cloth.
2. Check the power cord, plug and prongs for damage or excess play. If any
damage or excess play is found, contact your MovinCool reseller or a qualified
technician for repair.
3. Check the air filters and drain tank.
4. Clean the outside of the unit(s) with a damp cloth or mild nonabrasive cleaner.
Off-Season
1. Operate the unit in FAN ONLY mode for 8 hours.
Note: Operation is necessary to dry out the inside of the unit.
2. Disconnect the power cord from the AC outlet.
3. Check the prongs and surface of the power cord plug for dust and/or dirt. If
dust and/or dirt are present, wipe off with a clean dry cloth.
4. Check the power cord, plug and prongs for damage or excess play. If any
damage or excess play is found, contact your MovinCool reseller or a qualified
technician for repair.
5. Clean the air filters.
6. Empty all water from the drain tank.
26
TROUBLESHOOTING
Check the following items before calling your MovinCool reseller or a qualified
technician.
CONDITIONS
Unit does not operate.
Insufficient cooling.
POSSIBLE CAUSE
REMEDY
1. Ground fault breaker trip
or LCDI power cord trip.
Reset breaker or reset power
cord.
2. Drain tank is full.
LED displays "FL".
Empty the drain tank.
3. High pressure switch
activated 10 times in 24
hours.
1. Clean air filter.
2. Check inlet and outlet air
to make sure that there
are no objects preventing
the air flow into or out from
the unit.
3. Check environmental
condition whether it is
within operation range or
not.
4. RESET controller.
To RESET: Hold down the
SET TEMP ( / )
buttons simultaneously for
3 seconds, and the
controller returns to
normal operation.
1. Dirty/Blocked air filters.
Clean air filter.
2. Air inlet/outlet blocked.
Clean air inlet/outlet.
3. Improper temperature
setting.
Adjust temperature setting.
If conditions persist after the above actions have been taken, turn the unit off,
disconnect the power and contact your MovinCool reseller or a qualified
technician.
27
TECHNICAL SPECIFICATIONS OF CLASSIC 10
ITEM
SPECIFICATIONS
Electronic Features
Operation
Digital Electronic
Electrical Characteristics
Voltage Requirement
Single-Phase, 115 V, 60 Hz
Operating
Max.
Voltage Range Min.
127 V
Recommended Fuse Size
15 A
104 V
Cooling Capacity and Power Consumption
Evaporator: 95 °F (35 °C), Total Cooling Capacity
60 %RH
Sensible Cooling Capacity
Condenser: 95 °F (35 °C),
Power Consumption
60 %RH
Current Consumption
10,000 Btu/h (2,940 W)
4,500 Btu/h (1,320 W)
1.05 kW
9.7 A
EER
9.5
Compressor
Type of Compressor
Hermetic Rotary
Evaporator
Type of Fan
Centrifugal Fan
265 CFM (451 m3/h)
0.33 IWG (82 Pa)
Air Flow
Max. External Static
Pressure
Condenser
Type of Fan
Centrifugal Fan
740 CFM (1,258 m3/h)
R-410A
Air Flow
Refrigerant
Type
Amount
Power Cord
1.43 lb (0.65 kg)
NEMA Plug Configuration
Gauge x Length
Dimension
WxDxH
Weight
Net
5-15
14 AWG (3-core) x 10 ft (3.0 m)
19.4 x 26.5 x 41.5 in
(493 x 673 x 1,054 mm)
156 lb (71 kg)
Drain Tank Capacity
5.0 gal (19 L)
Operating Condition
Range
Inlet Air
Temperature
Maximum Duct Length
Cold Duct
40 ft (12.2 m)
Hot Duct
60 ft (18.3 m)
Sound Level*1
Max.
104 °F (40 °C), 50 %RH
Min.
70 °F (21 °C), 50 %RH
With Condenser Duct
55 dB (A)
Without Condenser Duct
58 dB (A)
• Specifications are subject to change without notice.
Note:
*1: Measured at 3 feet (1.0 m) from surface of the unit.
28
TECHNICAL SPECIFICATIONS OF CLASSIC 18
ITEM
SPECIFICATIONS
Electronic Features
Electrical Characteristics
Operation
Voltage Requirement
Operating
Max.
Voltage Range Min.
Recommended Fuse Size
Cooling Capacity and Power Consumption
Evaporator: 95 °F (35 °C), Total Cooling Capacity
60 %RH
Condenser: 95 °F (35 °C), Sensible Cooling Capacity
60 %RH
Compressor
Evaporator
Condenser
Refrigerant
Power Cord
Dimension
Weight
Drain Tank Capacity
Operating Condition
Range
Maximum Duct Length
Sound Level*1
Digital Electronic
Single-Phase, 208/230 V, 60 Hz
250 V
198 V
15 A
18,000 Btu/h (5,280 W)/
18,000 Btu/h (5,280 W)
8,600 Btu/h (2,520 W)/
8,600 Btu/h (2,520 W)
1.90 kW/1.90 kW
9.1 A/8.8 A
9.5/9.5
Hermetic Rotary
Centrifugal Fan
Power Consumption
Current Consumption
EER
Type of Compressor
Type of Fan
Air Flow
Max. External Static
Pressure
Type of Fan
Air Flow
Type
Amount
NEMA Plug Configuration
Gauge x Length
WxDxH
Net
Inlet Air
Temperature
Max.
Min.
Cold Duct
Hot Duct
With Condenser Duct
Without Condenser Duct
510 CFM (867 m3/h)/
530 CFM (901 m3/h)
0.48 IWG (120 Pa)
Centrifugal Fan
1,100 CFM (1,870 m3/h)/
1,180 CFM (2,006 m3/h)
R-410A
1.76 lb (0.80 kg)
6-15
14 AWG (3-core) x 6 ft (1.8 m)
19.4 x 26.5 x 41.5 in
(493 x 673 x 1,054 mm)
164 lb (74 kg)
5.0 gal (19 L)
104 °F (40 °C), 50 %RH
70 °F (21 °C), 50 %RH
50 ft (15.2 m)
60 ft (18.3 m)
63 dB (A)
67 dB (A)
• Specifications are subject to change without notice.
Note:
*1: Measured at 3 feet (1.0 m) from surface of the unit.
29
WARRANTY STATEMENT
DENSO PRODUCTS AND SERVICES AMERICAS, INC. ("DENSO") warrants its
MOVINCOOL Products only to the extent stated in its official written warranties. Unless
otherwise specifically provided in writing by DENSO, DENSO warrants to the original end-user
that the products shall be free of defects in materials or workmanship and will function in
accordance with DENSO's published specifications under ordinary intended use and service
for a period listed below beginning from the date of purchase on the invoice to the end-user:
Model(s): Classic 10, Classic 18
Warranty: 3 Years with warranty registration OR 1 Year for unregistered units.
DENSO shall, at its sole discretion, repair or replace any defective product covered by this
warranty. Such remedy shall be end-user's sole remedy with respect to any particular defect
in the products.
This warranty does not cover defects or malfunctions which result from causes beyond
DENSO's control, including, without limitation, (i) unusual physical or electrical stress; (ii)
accident, neglect, abuse, misuse or other abnormal use; (iii) failure to perform routine
maintenance in accordance with DENSO's recommended procedures; (iv) normal wear and
tear; (v) repairs or attempted repairs by an unauthorized person; (vi) modifications or
alterations to the products; (vii) use with parts or devices not supplied or approved by
DENSO; (viii) improper installation or service; (ix) shipping damage to any units or spare
parts during shipping. This includes and is not limited to compressors, evaporators and
condenser coils. This warranty shall extend only to the original end-user and shall be void if
any labels or other identifying marks permanently affixed to products when shipped by
DENSO are removed, altered, defaced or obliterated.
TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY, AS LIMITED HEREIN, SHALL
BE IN LIEU OF AND EXCLUSIVE OF ALL OTHER WARRANTIES, EITHER EXPRESSED
OR IMPLIED, ON THE PART OF DENSO PRODUCTS AND SERVICES AMERICAS, INC.,
OR DENSO CORPORATION, WHETHER ARISING FROM LAW, COURSE OF DEALING,
USAGE OF TRADE, OR OTHERWISE, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS OF A PARTICULAR
PURPOSE OR ANY LIABILITY FOR COMMERCIAL LOSSES BASED UPON
NEGLIGENCE OR MANUFACTURER'S STRICT LIABILITY. EXCEPT AS EXPRESSLY
PROVIDED HEREIN, NEITHER DENSO PRODUCTS AND SERVICES AMERICAS, INC.,
NOR DENSO CORPORATION WILL, IN ANY EVENT, BE LIABLE FOR LOST PROFITS,
COSTS OF PROCESSING, INJURY, GOODWILL, OR ANY OTHER CONSEQUENTIAL
DAMAGES OF ANY KIND ARISING FROM BREACH OF THIS WARRANTY.
DENSO PRODUCTS AND SERVICES AMERICAS, INC. reserves the right to make
changes without prior notice. MovinCool®, Office Pro® and SpotCool® are registered
trademarks of DENSO Corporation.
PURCHASE DATE:
SERIAL NUMBER:
P/N: 484007-3631EN
Second Issue: April 2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising