Eldes EBU1 User manual

Eldes EBU1 User manual
ESIM110
ESIM120
GSM SWITCH-GATE CONTROLLER
User Manual v3.1
Valid for ESIM110/ESIM120 v11.03.03 and up
SAFETY INSTRUCTIONS
Please read and follow these safety guidelines to safeguard yourself and others:
• GSM switch-gate controller ESIM110/ESIM120 (later referred to as “the system” or “ the device”) contains a built-in radio transceiver
operating in GSM 850/900/1800/1900 MHz bands.
• DO NOT use the system where it can cause potential danger and interfere with other devices – such as medical devices.
• DO NOT use the system in hazardous environment.
• DO NOT expose the system to high humidity, chemical environment or mechanical impact.
• DO NOT attempt to repair the system yourself – any repairs must be carried out by fully qualified personnel only.
Disconnect the mains power before installing. Never install or carry out maintenance during stormy weather. The electric socket that powers the system must be easily accessible.
Please use the 10-24V 50Hz ~200mA AC or 10-24V
200mA DC power supply unit that meets the EN 60950-1 standard.
Any additional device you connect to the system, such as a computer, must also be powered by an EN 60950-1 approved
supply. When connecting the power supply to the system, switching the polarity terminal places does not have any affect.
External power supply can be connected to AC mains only inside installation room
with automatic 2-pole circuit breaker capable of disconnecting circuit in the event
of short circuit or over-current condition. Open circuit breaker must have a gap
between connections of more than 3mm and the disconnection current 5A.
Phase
Null
PE
AC/DC
AC 230V
50 Hz/DC 24V
ESIM110/
ESIM120
USB cable
To switch the system off, unplug the external electric power supply from or any other linked device that the system is
powered from
A blown fuse cannot be replaced by the user. The replacement fuse has to be of the kind indicated by the manufacturer (fuse
F1 model – MINISMDC050F 0.5A).
If you use a computer for the device configuration, it must be earthed.
The WEEE (Waste Electrical and Electronic Equipment) symbol on this product (see left) means it must not be disposed of in
household waste. To prevent possible harm to human health and/or the environment, you must dispose of this product in an
approved and environmentally safe recycling facility. For further information contact your system supplier, or your local waste
authority.
2
EN
ESIM110/ESIM120 Manual v.3.1
CONTENTS
1. GENERAL INFORMATION............................................................................................................................................................6
2. TECHNICAL SPECIFICATIONS.....................................................................................................................................................6
2.1. Electrical & Mechanical Characteristics..........................................................................................................................................................6
2.2. Main Unit, LED Indicator & Connector Functionality.................................................................................................................................... 7
2.3. Wiring Diagrams.................................................................................................................................................................................................8
3.INSTALLATION............................................................................................................................................................................9
4. GENERAL OPERATION..............................................................................................................................................................10
5. CONFIGURATION METHODS.....................................................................................................................................................10
5.1. SMS Text Messages..........................................................................................................................................................................................10
5.2. ELDES Configuration Tool...............................................................................................................................................................................10
5.3. Remote Configuration via Web Browser.......................................................................................................................................................10
6. SYSTEM LANGUAGE..................................................................................................................................................................14
7. SMS PASSWORD........................................................................................................................................................................15
8. ADMINISTRATOR PHONE NUMBERS........................................................................................................................................15
9. DATE AND TIME........................................................................................................................................................................17
9.1. Automatic Date and Time Synchronization.................................................................................................................................................17
10.USER PHONE NUMBER DATABASE..........................................................................................................................................19
10.1. User Validity and Access Restriction ............................................................................................................................................................21
11.OUTPUT (-S)............................................................................................................................................................................. 24
11.1. Output Name (-s)............................................................................................................................................................................................. 24
11.2. Output Control by Free of Charge Phone Call..............................................................................................................................................25
11.3. Output Control by SMS Text Message.......................................................................................................................................................... 26
11.4. Output Control Confirmation by Call Back................................................................................................................................................... 29
11.5. Output Control from any Phone Number.................................................................................................................................................... 30
11.6. Automatic Output Control.............................................................................................................................................................................. 30
12.SCHEDULERS............................................................................................................................................................................32
13.EVENT LOG............................................................................................................................................................................... 34
14.INPUTS.................................................................................................................................................................................... 36
14.1. Input Names and Alarm Notifications.......................................................................................................................................................... 36
14.2. Disabling and Enabling Inputs....................................................................................................................................................................... 38
15.SYSTEM INFORMATION. INFO SMS......................................................................................................................................... 39
15.1. Periodic Info SMS............................................................................................................................................................................................. 39
16.SYSTEM NOTIFICATIONS......................................................................................................................................................... 40
16.1. SMSC (Short Message Service Center) Phone Number............................................................................................................................. 40
17.GPRS NETWORK SETTINGS......................................................................................................................................................41
18.REMOTE SYSTEM RESTART..................................................................................................................................................... 42
19.TECHNICAL SUPPORT............................................................................................................................................................. 43
19.1.Troubleshooting.............................................................................................................................................................................................. 43
19.2. Restoring Default Parameters...................................................................................................................................................................... 43
19.3. Updating the Firmware via USB Cable......................................................................................................................................................... 43
20. RELATED PRODUCTS.............................................................................................................................................................. 44
ESIM110/ESIM120 Manual v.3.1
EN
3
4
EN
ESIM110/ESIM120 Manual v.3.1
Limited Liability
The buyer agrees that the system will reduce the risk of fire, theft, burglary or other danger but that it does not guarantee against the occurrence of such events. “ELDES UAB” will not take any responsibility for the loss of personal effects, property or revenue whilst using the
system. The liability of “ELDES UAB” is limited to the value of the system purchased. “ELDES UAB” is not affiliated with any mobile/wireless/
cellular provider and is therefore not responsible for the quality of such services.
Manufacturer Warranty
The system carries a 24-month manufacturer warranty from “ELDES UAB”. The warranty begins the day the system is purchased by the
user and the receipt must be retained as proof of purchase date. The warranty remains valid only if the system is used as intended, following all guidelines outlined in this manual and in accordance with the operating conditions specified. The warranty is void if the system
has been exposed to mechanical impact, chemicals, high humidity, fluids, corrosive and hazardous environments or force majeure factors.
Dear Customer,
Thank you for choosing to purchase the GSM switch-gate controller ESIM110/ESIM120. Your thoughtful decision will ensure reliable
solution for many years as all ELDES products are manufactured to meet the highest standards.
We are confident that you will be completely satisfied with your product. However, in the unlikely event that you do experience a
problem, please contact the dealer from whom you made your purchase.
UAB ELDES
www.eldes.lt
Contents of Pack
ItemQuantity
1. ESIM110/ESIM120.................................. 1
2. User manual............................................. 1
3. GSM antenna........................................... 1
Copyright © “ELDES UAB”, 2013. All rights reserved
It is strictly forbidden to copy and distribute information in this document or pass to a third party without an advanced
written authorization from “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby, “ELDES UAB” declares that the GSM switch-gate controller ESIM110/ESIM120 is
in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of
conformity may be consulted at www.eldes.lt.
ESIM110/ESIM120 Manual v.3.1
EN
5
1.GENERAL INFORMATION
ESIM110/ESIM120 is a micro-controller based device intended to provide access control for gate automatics, road barriers or to remotely
turn ON/OFF any electrical appliance via the GSM network.
Examples of using the system:
•
Access control.
•
Parking lot control of residential houses or offices.
•
Gate control of private houses.
•
Any electrical appliance control: lighting, watering, heating etc.
•
Remote reboot of the “frozen” systems, such as computer network or a server.
Main features
•
Manual output control by free of charge phone call.
•
Automatic output control in accordance with the scheduled time.
•
Configurable output pulse duration.
•
Automatic date and time synchronization.
•
Up to 5 administrators for system configuration by SMS text messages, acceptance of input alarm SMS text messages, output control
by SMS text message and free of charge phone call.
•
User database capacity – up to 500 (1000 – optional) users for output control by free of charge phone call.
•
User phone number validity limitation in accordance with a set deadline (date/time) or number of rings to the system.
•
Output control restriction for users in accordance with the specified weekdays and time.
•
Event log of 1000 events containing date and time as well as administrator/user phone number and user name who controlled the
output.
•
3 inputs with customizable alarm texts for notification on gate state or in case it gets jammed.
•
Periodic self-test notification by SMS text message to administrator phone number.
2.TECHNICAL SPECIFICATIONS
2.1. Electrical & Mechanical Characteristics
Supply voltage
10-24V 50Hz ~ 200mA max / 10-24V
Current used in standby mode
up to 50mA
GSM modem frequency
850/900/1800/1900 MHz
Number of outputs
1 (ESIM110); 2 (ESIM120)
Output type
Relay; NO (normally-open)
Maximum commuting output values
24V 50Hz ~ 0,5A / 24V
Number of “low” level (negative) inputs
2
Number of “high” level (positive) inputs
1
“Low” level (negative) input value range
0... 16V
-0.8... -0.4mA
“High” level (positive) input value range
5... 50V
0.17 .... 1.7mA
“Low” level (negative) and “high” level
(positive) input connection type
NO (normally-open)
Dimensions
70x85x57mm
Operating temperature range
-20…+55oC (-30...+55oC with limitations)
Humidity
0-90% RH @ 0... +40 °C (non-condensing)
6
EN
200mA max
1A
ESIM110/ESIM120 Manual v.3.1
2.2. Main Unit, LED Indicator & Connector Functionality
ESIM110
1
ESIM120
USB
USB
ANT
ANT
G SM
MO DE M
G SM
MO DE M
SIM CARD
SIM STAT
NETW
MIC
SIM STAT
NETW
MIC
DEF
DEF
F1
F1
AC/DC RELAY
SIM CARD
COM Z5 Z4 Z3 Z2 Z1
AC/DC RELAY1 RELAY2 COM Z5 Z4 Z3 Z2 Z1
Main Unit Functionality
ANT
GSM antenna SMA type connector
USB
Mini USB port
SIM CARD
SIM card slot / holder
GSM MODEM
GSM network 850/900/1800/1900 MHz modem
MIC
N/A
SIM STAT
Red light-emitting diode indicating SIM card status
NETW
Green light-emitting diode indicating GSM signal strength
DEF
Pins for restoring default settings
F1
0.5A fuse
Connector Functionality
AC/DC
Power supply terminals
RELAY
ESIM110 output C1 terminal
RELAY1
ESIM120 output C1 terminal
RELAY2
ESIM120 output C2 terminal
COM
Common terminal
Z5
N/A
Z4
N/A
Z3
“Low” level (negative) input terminal
Z2
“High” level (positive) input terminal
Z1
“Low” level (negative) input terminal
ESIM110/ESIM120 Manual v.3.1
EN
7
LED Indicator Functionality
SIM STAT indication
SIM card status
OFF
SIM card is not yet connected to the GSM network / SIM card is not present / PIN code enabled
Steady ON
SIM card is operating successfully
NETW indication
GSM signal strength
OFF
No GSM signal
Flashing every 1 sec.
Poor
Flashing several times per sec.
Medium
Steady ON
Excellent
2.3. Wiring Diagrams
General wiring
AC/DC
2
ESIM 110/ESIM120
RELAY COM
Z3
Z2 Z1
+
-
Power
supply
GATE AUTOMATION DEVICE
Example of ESIM120 system wiring to gate automation device
ESIM120
AC/DC RELAY1 RELAY2 COM Z5 Z4 Z3 Z2 Z1
GATE AUTOMATION DEVICE
F0
GND
3
+24v
FO= Fault output; open collector type
+24V = Power supply output for
powering aux. equipment
= Impulse input
GND = Common terminal
8
EN
ESIM110/ESIM120 Manual v.3.1
3.INSTALLATION
• The system should be installed indoors, in stationary environment ONLY.
• For the connection of input/output terminals, use 0.50 mm2 1 thread unshielded cable of up to 100 meters length.
1. Wire up the system in accordance with the wiring diagrams (see 2.3 Wiring Diagrams for more details).
2. Connect the GSM antenna. Based on the type of the GSM antenna supplied with ESIM110/ESIM120 unit, follow the recommendations
for the antenna installation:
Never install in the following
locations:
4
• inside the metal cabinet
GSM
antenna
• closer than 20 cm from the
metal surface and/or power
lines
3. Disable the PIN code request of the SIM card by inserting it into a mobile phone and following the proper menu steps.
4. Once the PIN code is disabled, insert the SIM card into the SIM card slot / holder of ESIM110/ESIM120 system.
5
6
5. Power up the system and wait until indicator SIM STAT lights up indicating SIM card status.
6. Once the indicator SIM STAT lights OFF, the illuminated indicator NETW lights up indicating that the system has successfully connected
to the GSM network. To find the strongest GSM signal, position the GSM antenna and follow the indications provided by NETW indicator
(see 2.2. Main Unit, LED Indicator & Connector Functionality for more details).
7. Change the system language if necessary (see 6. SYSTEM LANGUAGE for more details).
8. Change the default SMS password (see 7. SMS PASSWORD for more details).
9. Set the phone number for Admin 1 (see 8. ADMINISTRATOR PHONE NUMBERS for more details).
10. Set system date and time (see 9. DATE AND TIME for more details).
11. Once the system is fully configured, it is ready for use. However, if you fail to receive a reply by SMS text message from the system,
please check the SMSC (Short Message Service Center) phone number. For more details regarding the SMS center phone number,
please refer to 17. SMSC (Short Message Service Center) Phone Number.
ATTENTION: The system is NOT compatible with pure 3G SIM cards. Only 2G/GSM SIM cards and 3G SIM cards with 2G/GSM profile
enabled are supported. For more details, please contact your GSM operator.
ATTENTION: We also recommend you to disable call forwarding, voice mail/text message reports on missed/busy calls and
similar services that might cause incorrect system operation. Please contact your GSM operator for more details on these services and
how to disable them.
NOTE: For maximum system reliability we recommend you do NOT use a Pay As You Go SIM card. Otherwise, in the event of insufficient
credit balance on the SIM card, the system would fail to make a phone call or send SMS text messages.
NOTE: We advise you to choose the same GSM SIM provider for your system as for your mobile phone. This will ensure the fastest,
most reliable SMS text message delivery service and phone call connection.
NOTE: Even though the installation process of ESIM110/ESIM120 is not too complicated, we still recommend to perform it by a person
with basic knowledge in electrical engineering and electronics to avoid any system damage.
ESIM110/ESIM120 Manual v.3.1
EN
9
4.GENERAL OPERATION
When a phone call is made to the phone number of the SIM card inserted in ESIM110/ESIM120, the system will verify if the caller’s phone
number exists in the memory. If the caller is one of the 5 administrators or the phone number belongs to one of the 500 database users, the
system will reject the phone call, thus making the phone call free of charge, and open the gate. By ringing to ESIM110/ESIM120 again, it will
close the gate. If the phone number is not recognized, the system will reject the phone call and ignore it. The GSM switch-gate controller
can also control your gate automatically in accordance with the scheduled time or by sending an SMS text message from the administrator’s
phone number.
By connecting a sensor to one of the 3 inputs, the administrators can receive SMS text messages regarding the gates that failed to close
during the set time period.
7
CALL
User/Admin
ESIM110/ESIM120
5.CONFIGURATION METHODS
5.1. SMS Text Messages
!!! In this installation manual the underscore character ”_” represents one space character. Every underscore character
must be replaced by a single space character. There must be no spaces or other unnecessary characters at the beginning
and at the end of the SMS text message.
In order to configure and control the system by SMS text message, send the text command to the ESIM110/ESIM120 system
phone number from one of the preset administrator phone numbers. The structure of SMS text message consists of 4-digit
SMS password (the default SMS password is 0000 – four zeros), the parameter and value. For some parameters the value does
not apply e. g. STATUS. The variables are indicated in lower-case letters, while a valid parameter value range is indicated in
brackets.
SMS
5.2. ELDES Configuration Tool
Software ELDES Configuration Tool is intended for ESIM110/ESIM120 GSM switch-gate controller configuration via USB port
Config
locally. This software simplifies system configuration process by allowing to use a personal computer in the process. Before
Tool
starting to use ELDES Configuration Tool software, please read the user guide provided in the software’s HELP section.
ELDES Configuration Tool is freeware and can be downloaded at: www.eldes.lt/en/download
NOTE: ELDES Configuration Tool software is secured with SMS password. The default SMS password is 0000 (see 7. SMS PASSWORD).
5.3. Remote Configuration via Web Browser
The system comes equipped with a remote configuration feature allowing to configure the parameters via any available web
browser. Before remotely connecting to ESIM110/ESIM120 via GPRS connection, ensure that:
WEB
BROWSER
10
EN
•
SIM card is inserted into the SIM CARD slot (see 2.2. Main Unit, LED & Connector Functionality).
•
Mobile internet service (GPRS) is enabled on the SIM card.
•
ESIM110/ESIM120 is powered up.
•
Default SMS password is changed to a new 4-digit password (see 7. SMS PASSWORD).
•
Admin 1 phone number is set up (see 8. ADMINISTRATOR PHONE NUMBERS).
•
APN, user name and password are set up (see 17. GPRS NETWORK SETTINGS).
ESIM110/ESIM120 Manual v.3.1
The system supports the following remote connection modes:
• CLIENT – The device connects to the configuration server making the device accessible through a web browser when the administrator
logs in via ELDES website (see 5.3.1. Establishing Remote Connection). This mode is set by default and DOES NOT require the static
IP address for the device SIM card. Default Client mode parameters are as follows:
• Server IP – config.eldes.lt
• DNS1 – 84.32.3.34
• DNS1 – 84.32.134.1
• Port – 5555
• SERVER – The device is accessible directly through a web browser using the device IP address and local port number (see
5.3.1. Establishing Remote Connection). A static IP address, provided by GSM operator, is required for the device SIM card. This mode
is for advanced use only. Default Server mode parameters are as follows:
• Local Port – 5000
• Protocol – TCP
Set remote
connection mode
as Server
SMS
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Set local port
SMS
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
SMS
SMS text message content:
sssss_SETGPRS:PROTOCOL:ptc
Value: ssss – 4-digit SMS password; ptc – protocol, range – [TCP... UDP].
Example: 1111_SETGPRS:PROTOCOL:UDP
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ESIM110/ESIM120 Manual v.3.1
SMS text message content:
ssss_SETGPRS:LPORT:lpprt
Value: ssss – 4-digit new SMS password; lpprt – local port number, range – [1... 65535].
Example: 1111_SETGPRS:LPORT:5000
Config
Tool
BROWSER
Set protocol
SMS text message content:
ssss_SETGPRS:TYPE:SERVER
Value: ssss – 4-digit new SMS password.
Example: 1111_SETGPRS:TYPE:SERVER
EN
11
Set remote
connection mode as
Client
SMS
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Set server IP address
SMS
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
SMS
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Set DNS2 server IP
address
BROWSER
12
EN
SMS text message content:
ssss_SETGPRS:PORT:pprrt
Value: ssss – 4-digit SMS password; pprrt – server port number, range – [1... 65535].
Example: 1111_SETGPRS:PORT:5521
Config
Tool
BROWSER
Set DNS1 server IP
address
SMS text message content:
ssss_SETGPRS:IP:add.add.add.add
Value: ssss – 4-digit SMS password; add.add.add.add – server IP address.
Example: 1111_SETGPRS:IP:65.82.119.5
Config
Tool
BROWSER
Set server port
SMS text message content:
ssss_SETGPRS:TYPE:CLIENT
Value: ssss – 4-digit new SMS password.
Example: 1111_SETGPRS:TYPE:CLIENT
ESIM110/ESIM120 Manual v.3.1
View remote
configuration
parameters
SMS
SMS text message content:
ssss_SETGPRS?
Value: ssss – 4-digit SMS password.
Example: 1111_SETGPRS?
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
5.3.1.Establishing Remote Connection
1. In order to activate a remote connection, please send the following SMS text message from user phone number. Upon the successful
SMS text message delivery, the system establishes a connection session for 20 minutes. An SMS reply, containing temporal user name
and password, will be sent shortly.
Establish remote
connection
SMS
SMS text message content:
ssss_CONNECT:PROFILE1
Value: ssss – 4-digit new SMS password.
Example: 1111_CONNECT:PROFILE1
To set a different session duration or connect for a custom session duration, please refer to the following configuration methods.
Set session duration
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Establish remote
connection for custom
session duration
SMS
SMS text message content:
ssss_CONNECT:TIMEOUT:ses-d
Value: ssss – 4-digit new SMS password; ses-d – session duration, range – [0... 14400] minutes.
Example: 1111_CONNECT:TIMEOUT:120
Alternatively, the system supports remote connection establishment by making a phone call from the administrator phone number to
the system. Once the call is received, the system rejects the call thus making it free of charge and replies with the login details by SMS
text message to the administrator phone number. By default, this feature is disabled. To enable/disable it, please refer to the following
configuration methods.
Enable/disable
remote connection
establishment by
phone call
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ESIM110/ESIM120 Manual v.3.1
EN
13
NOTE: 0 value sets unlimited session duration.
NOTE: ELDES Configuration Tool software and remote configuration web interface allows to set the unlimited session duration value.
NOTE: Once the remote connection establishment by phone call is enabled, the specified administrator will no longer be able to
control the output via free of charge phone call.
2. a) If running in Client mode, open a web browser and type in http://www.eldes.lt/login.
b) If running in Server mode, open a web browser and type in http://deviceIPaddress:localport
3. Enter the received login details and press Login button.
4. After the system configuration is complete, use one of the following methods to end the configuration process:
• Wait for the session timeout and the system to reply with an SMS text message confirming the end of the session.
• Shut down the connection with the configuration server at any time by sending an SMS text message.
Shut down the
connection with
configuration server
SMS
SMS text message content:
ssss_STOP
Value: ssss – 4-digit new SMS password.
Example: 1111_STOP
ATTENTION: Output control is disabled during the remote configuration process.
6.SYSTEM LANGUAGE
The system comes equipped with a multiple languages for communication with the administrator by SMS text messages. The default
system language depends on the firmware, which is based on the customer’s location.
List of currently available system languages:
• English
• Estonian
• German
• Lithuanian
• French
• Slovak
Set system language
SMS
SMS text message content:
LN
Value: LN – language index; range – [EN – English, EE – Estonian, DE – German, LT – Lithuanian, FR – French, SK – Slovak].
Example: LT
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
NOTE: To change the language once the system has already been configured, you need to reset the device to the default configuration. For more details on how to do this, please refer to 19.2. Restoring Default Parameters.
14
EN
ESIM110/ESIM120 Manual v.3.1
7.SMS PASSWORD
For security reasons, the system uses the following type of password:
•
SMS password – 4-digit password used for system configuration and control from administrator phone number by SMS text
messages and logging in to ELDES Configuration Tool software . By default, SMS password is 0000, which MUST be changed!
Set SMS password
SMS
SMS text message content:
wwww_PSW_ssss
Value: wwww – 4-digit default SMS password; ssss – 4-digit new SMS password; range –
[0001... 9999].
Example: 0000_PSW_1111
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
NOTE: The system rejects the SMS text messages containing wrong SMS password even from a preset administrator phone number.
8.ADMINISTRATOR PHONE NUMBERS
The system supports up to 5 administrator phone numbers identified as Admin 1 through 5. When the phone number is set, the
administrator will be able to configure and control the system by SMS text messages as well as by free of charge phone call and receive the
input alarm SMS text messages from the system (see 14.1. Input Names and Alarm Notification). ESIM120 allows to assign output C1,
output C2 or both outputs (simultaneous control) to a certain administrator.
By default, the system ignores any incoming calls and SMS text messages from a non-preset phone number as well as it rejects the SMS
text messages containing wrong SMS password even from a preset administrator phone number. For more details on how to enable output
control from a non-preset phone number, please refer to 11.5. Output Control from any Phone Number.
To set Admin 1 phone number is mandatory, while the other 4 are optional. The supported phone number format is the following:
• International (w/o plus) – The phone numbers must be entered starting with an international country code in the following format:
[international code][area code][local number], example for UK: 4417091111111.
Set administrator
phone number
SMS
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
View administrator
phone numbers
SMS
SMS text message content:
ssss_HELPNR
Value: ssss – 4-digit SMS password.
Example: 1111_HELPNR
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ESIM110/ESIM120 Manual v.3.1
SMS text message content:
ssss_NRas:ttteeellnnuumm
Value: ssss – 4-digit SMS password; as – administrator phone number slot, range – [1... 5];
ttteeellnnuumm – up to 15 digits administrator phone number.
Example: 1111_NR1:4417091111111
EN
15
Assign output
(-s) to individual
administrator
ONLY FOR ESIM120
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Delete administrator
phone number
SMS
SMS text message content:
ssss_NRas:DEL
Value: ssss – 4-digit SMS password; as – administrator phone number slot, range – [2... 5].
Example: 1111_NR2:DEL
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ATTENTION: NEVER set a phone number of the device’s SIM card as an administrator phone number!
ATTENTION: Once Admin 1 phone number is set, the system will restrict only to modify it
ATTENTION: Multiple administrator phone numbers can be set by a single SMS text message, Example: 1111_NR1:4417091111111_
NR5:4417091111112_NR2:4417091111113_NR3: 4417091111114
NOTE: Multiple administrator phone numbers can be deleted by a single SMS text message, Example: 1111_NR2:DEL_NR4:DEL_
NR3:DEL
NOTE FOR ESIM120: The administrator can control any output by SMS text message regardless of the output assigned to the administrator phone number (see 11.3. Output Control by SMS Text Message).
For more details on output control, please refer to 11. OUTPUT (-S).
16
EN
ESIM110/ESIM120 Manual v.3.1
9.DATE AND TIME
The system comes equipped with internal real-time clock (RTC) that keeps track of the current date and time. Once the system is up and
running, the user must set the correct date and time, otherwise the system will not operate properly. By default, after shutting down and
starting up the system, the date and time must be set again. In order to avoid manual date and time set up, please use the automatic date
and time synchronization feature (see 9.1. Automatic Date and Time Synchronization).
Set date and time
SMS
SMS text message content:
ssss_yyyy.mm.dd_hr:mn
Value: ssss – 4-digit SMS password; yyyy – year; mm – month, range – [01... 12]; dd – day,
range – [01... 31]; hr – hours, range – [00... 23]; mn – minutes, range – [00... 59].
Example: 1111_2013.03.16_14:33
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
9.1. Automatic Date and Time Synchronization
This feature enables the system to set the date and time automatically without the user being involved in this process. The system supports
the following methods of automatic date and time synchronization that are used automatically on system start-up and periodically (by
default – every 30 days):
• Via GSM network – Once enabled, the system automatically sends a date/time request to the GSM operator. This method is the
most accurate synchronization method. Some GSM operators might not support it.
• By SMS text message – Once enabled, the system automatically sends the SMS text message to its own phone number and
retrieves the date and time from the SMS text message reply, as the included date and time is set by the SMSC (SMS center). This
method is not as accurate as the synchronization via GSM network, but always effective.
By default, synchronization via GSM network is disabled. To enable/disable automatic date and time synchronization via GSM network,
please refer to the following configuration methods.
Enable/disable
synchronization via
GSM network
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
By default, synchronization by SMS text message is disabled. To enable/disable automatic date and time synchronization by SMS text
message, please enter/remove device phone number using one of the following configuration methods.
Enter/remove device
phone number for
synchronization by
SMS text message
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ESIM110/ESIM120 Manual v.3.1
EN
17
By default, the date and time synchronization period is 30 days. To set a different period, please refer to the following configuration
methods.
Set synchronization
period
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
NOTE: When setting up automatic date and time synchronization feature remotely, you may wish to restart the system when done.
For more details, please refer to 18. REMOTE SYSTEM RESTART.
NOTE: 0 value disables periodic date and time synchronization.
NOTE: When both synchronization methods are enabled, the system will always attempt to synchronize date and time via GSM network every time the system shuts down and starts up again and in accordance with the set period value. In the event of first method’s
failure, the system will attempt to use the SMS text message method as a backup.
18
EN
ESIM110/ESIM120 Manual v.3.1
10.USER PHONE NUMBER DATABASE
The system comes equipped with a user database of 500 user capacity. When the phone number is set, the user will be able to control
the output (-s) by free of charge phone call. ESIM120 user database allows to assign output C1, output C2 or both outputs (simultaneous
control) to a certain user. The supported phone number format is the following:
• International (w/o plus) – The phone numbers must be entered starting with an international country code in the following
format: [international code][area code][local number], example for UK: 4417091111111.
ESIM110/ESIM120 user database supports user validity and access restriction features. For more details, please refer to 10.1. User
Validity and Access Restriction.
Optionally, a user name can be set that typically specifies the owner’s name of a certain phone number, for example: John.
The phone number and user name (if any) are used when searching for a certain user in the database as well as they are automatically
added in the event log after the successful output control event (see 13. EVENT LOG).
Add user phone
number (and user
name)
SMS
SMS text message content:
ssss_N:ttteeellnnuumm or ssss_N:ttteeellnnuumm:user-name
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number;
user-name – up to 16 characters user name.
Example: 1111_N:4417091111111:John
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
View user phone
numbers
SMS
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Search for user by
phone number or
name
SMS text message content:
ssss_GETALLNUMBERS
Value: ssss – 4-digit SMS password.
Example: 1111_GETALLNUMBERS
SMS
SMS text message content:
ssss_T:ttteeellnnuumm or ssss_T:user-name
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number;
user-name – up to 16 characters user name.
Example: 1111_T:John
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ESIM110/ESIM120 Manual v.3.1
EN
19
Assign output (-s) to
individual user
SMS
ONLY FOR ESIM120
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Delete individual user
SMS text message content:
ssss_OUTPUT_ttteeellnnuumm_o or ssss_OUTPUT_user-name_o
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number;
o – output number; range [1 – output C1; 2 – output C2; 3 – both outputs]; user-name – up
to 16 characters user name.
Example: 1111_OUTPUT_4417091111111_2
SMS
SMS text message content:
ssss_D:ttteeellnnuumm or ssss_D:user-name
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number;
user-name – up to 16 characters user name.
Example: 1111_GETALLNUMBERS
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Delete all users
SMS
SMS text message content:
ssss_D:ALL
Value: ssss – 4-digit SMS password.
Example: 1111_D:ALL
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
The user database can be exported/imported to/from a .csv file for backup purposes or for a convenient user database management. To
export/import an existing user database, please refer to the following configuration method.
Export/import
existing user database
from/to file
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, the user database is enabled and output control by all database users is permitted. To deny output control instead of deleting
all users from the database, please disable the user database using one of the following configuration methods.
20
EN
ESIM110/ESIM120 Manual v.3.1
Disable user database
SMS
SMS text message content:
ssss_DBM_OFF
Value: ssss – 4-digit SMS password.
Example: 1111_DBM_OFF
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
To enable user database, please refer to the following configuration methods.
Enable user database
SMS
SMS text message content:
ssss_DBM_ON
Value: ssss – 4-digit SMS password.
Example: 1111_DBM_ON
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ATTENTION: Space and colon characters are NOT allowed in the user names.
NOTE: Multiple users can be added by a single SMS text message, Example: 1111_N:4417091111111:John_ 4417091111112:_
4417091111113:Tom
NOTE: Multiple users can be deleted by a single SMS text message, Example: 1111_D:John_ 4417091111113_Mark
For more details on output control, please refer to 11. OUTPUT (-S).
10.1. User Validity and Access Restriction
The system allows to restrict access in accordance with the scheduler assigned to a certain user. When one or more schedulers are
assigned, the user will be able to control the output only on the specified weekdays and time set up in the scheduler. The system allows to
assign up to 8 different schedulers. For more details on how to set up the schedulers, please refer to 12. SCHEDULERS.
In addition, the system allows to limit the user validity by the following methods:
• Deadline (valid until) – When a specified date and time hits, the user will be automatically deleted from the database.
• Ring counter – When a specified number of phone calls to the system expires, the user will be automatically deleted from the
database.
Assign scheduler to
individual user
SMS
SMS text message content:
ssss_NSCHED_ttteeellnnuumm_c:ON or ssss_NSCHED_user-name_c:ON
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number;
c – scheduler number; range – [1... 8]; user-name – up to 16 characters user name.
Example: 1111_NSCHED_John_5:ON
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ESIM110/ESIM120 Manual v.3.1
EN
21
Remove scheduler
from individual user
SMS
SMS text message content:
ssss_NSCHED_ttteeellnnuumm_c:OFF or ssss_NSCHED_user-name_c:OFF
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number;
c – scheduler number; range – [1... 8]; user-name – up to 16 characters user name.
Example: 1111_NSCHED_John_5:OFF
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Set deadline for
individual user
SMS
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Extend deadline for
individual user
SMS text message content:
ssss_EXPIRYTIME_ttteeellnnuumm_yyyy.mm.dd_hr:mn or ssss_EXPIRYTIME_username_yyyy.mm.dd_hr:mn
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number;
yyyy – year; mm – month, range – [01... 12]; dd – day, range – [01... 31]; hr – hours, range
– [00... 23]; mn – minutes, range – [00... 59]; user-name – up to 16 characters user name.
Example: 1111_EXPIRYTIME_John_2015.06.29_19:35
SMS
SMS text message content:
ssss_EXPIRYTIME_ttteeellnnuumm_extendmins or ssss_EXPIRYTIME_user-name_
extendmins
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number; extendmins – time period, range – [1... 2147483648] minutes; user-name – up to 16
characters user name.
Example: 1111_EXPIRYTIME_John_2350
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
View set up deadline
for individual user
SMS
SMS text message content:
ssss_EXPIRYTIME_ttteeellnnuumm_? or ssss_EXPIRYTIME_user-name_?
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number;
user-name – up to 16 characters user name.
Example: 1111_EXPIRYTIME_4417091111111_?
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
22
EN
ESIM110/ESIM120 Manual v.3.1
Remove deadline from
individual user
SMS
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Set ring counter for
individual user
SMS text message content:
ssss_EXPIRYTIME_ttteeellnnuumm_0 or ssss_EXPIRYTIME_user-name_0
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number;
user-name – up to 16 characters user name.
Example: 1111_EXPIRYTIME_4417091111111_0
SMS
SMS text message content:
ssss_RCOUNT_ttteeellnnuumm_numofcalls or ssss_RCOUNT_user-name_numofcalls
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits administrator phone
number; user-name – up to 16 characters user name; numofcalls – number of phone calls,
range – [0... 4294967296].
Example: 1111_RCOUNT_4417091111111_152
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
View set up ring
counter value for
individual user
SMS
SMS text message content:
ssss_RCOUNT_ttteeellnnuumm_? or ssss_RCOUNT_user-name_?
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits administrator phone
number; user-name – up to 16 characters user name.
Example: 1111_RCOUNT_John_?
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Remove ring counter
from individual user
SMS
SMS text message content:
ssss_RCOUNT_ttteeellnnuumm_0 or ssss_RCOUNT_user-name_0
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits administrator phone
number; user-name – up to 16 characters user name.
Example: 1111_RCOUNT_John_0
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ATTENTION: If the date and time are not set, the system will NOT be able to manage user validity and access. For more details on how
to set date and time, please refer to 9. DATE AND TIME.
ESIM110/ESIM120 Manual v.3.1
EN
23
NOTE: Multiple schedulers can be assigned/removed by a single SMS text message, Example: 1111_NSCHED_
John_2:ON_6:OFF_3:OFF_5:ON
NOTE: 0 value removes the set up deadline from the user.
NOTE: 0 value removes the set up ring counter from the user.
11.OUTPUT (-S)
ESIM110 comes equipped with 1 built-in output, while ESIM120 – with 2 outputs. The output (-s) is intended for connection and control of
the gate automation device by the following methods:
• Free of charge phone call from the user or administrator phone number (see 11.2. Output Control by Free of Charge Phone Call).
• SMS text message from the administrator phone number (see 11.3. Output Control by SMS Text Message).
• Automatically in accordance with the scheduled weekdays and time (see 11.6. Automatic Output Control).
The system allows to view the current output state by the following configuration method.
View output state
SMS
SMS text message content:
ssss_STATUS
Value: ssss – 4-digit SMS password.
Example: 1111_STATUS
ATTENTION: Once the scheduler, set up for automatic output control, comes into effect, the user/administrator will NOT be able to
control the output by phone call and SMS text message (see 11.6. Automatic Output Control).
11.1. Output Name (-s)
The output (-s) has a name that can be customized. Typically, the name specifies a device type connected to a determined output, for
example: Gate. The name can be used instead of output number when controlling the output by SMS text message.
By default, the output names are: C1 – Controll1 (ESIM110, ESIM120), C2 – Controll2 (ESIM120).
Set output name
SMS
Example: 1111_C1:OFF:00.10.15
ONLY FOR ESIM110
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Set output name
SMS
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
EN
SMS text message content:
ssss_Co:out-name
Value: ssss – 4-digit SMS password; o – output number, range [1 – output C1; 2 – output
C2]; out-name – up to 16 characters output name.
Example: 1111_C1:OFF:00.10.15
ONLY FOR ESIM120
24
SMS text message content:
ssss_C1:out-name
Value: ssss – 4-digit SMS password; out-name – up to 16 characters output name.
ESIM110/ESIM120 Manual v.3.1
View output name
SMS
SMS text message content:
ssss_STATUS
Value: ssss – 4-digit SMS password.
Example: 1111_STATUS
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ATTENTION: Space, colon, semi-colon characters, parameter names and/or values, such as PSW, STATUS, ON, OFF etc. are NOT
allowed in output names.
11.2. Output Control by Free of Charge Phone Call
To open or close the gate, dial the system’s phone number from any available user or administrator phone numbers (see 10. USER PHONE
NUMBER DATABASE and 8. ADMINISTRATOR PHONE NUMBERS for phone number management). The phone call is free charge as
the system rejects it and turns ON the output (-s) for the preset time period (pulse; by default – 2 seconds) resulting in the gate opening or
closing, depending on the current gate state. If there is more than one preset caller dialing to the system at the same time, the system will
accept the incoming call from the caller who was the first to dial while other caller (-s) will be ignored.
The system supports a confirmation phone call to user/administrator phone number. For more details, please refer to 11.4. Output
Control Confirmation by Call Back
Set output pulse
duration
SMS
SMS text message content:
ssss_TIMER1:pl
Value: ssss – 4-digit SMS password; pl – pulse duration, range – [1... 10] seconds.
Example: 1111_TIMER1:8
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Set output pulse
duration
SMS
SMS text message content:
ssss_TIMERo:pl
Value: ssss – 4-digit SMS password; o – output number, range [1 – output C1; 2 – output
C2]; pl – pulse duration, range – [1... 10] seconds.
Example: 1111_TIMER2:4
ONLY FOR ESIM120
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
NOTE: ELDES Configuration Tool software and remote configuration web interface allows to set the unlimited output pulse duration
value.
ESIM110/ESIM120 Manual v.3.1
EN
25
11.3. Output Control by SMS Text Message
To open or close the gate, send the SMS text message from any of 5 available administrator phone numbers (see 8. USER PHONE
NUMBER DATABASE for phone number management). The system will turn ON the output (-s) for a determined time period (pulse)
resulting in the gate opening or closing, depending on the current gate state. The confirmation reply by SMS text message, containing the
output name (see 11.1. Output Name (-s)), will be sent to the administrator phone number that the output control by SMS text message
was initiated from.
Turn ON output
for time period
SMS
Example: 1111_Gate:ON:00.00.02
ONLY FOR ESIM110
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Turn OFF output
for time period
SMS text message content:
ssss_C1:ON:hr.mn.sc or ssss_out-name:ON:hr.mn.scv
Value: ssss – 4-digit SMS password; hr – hours, range – [00... 23]; mn – minutes, range –
[00... 59]; sc – seconds, range – [00... 59]; out-name – up to 16 characters output name.
SMS
SMS text message content:
ssss_C1:OFF:hr.mn.sc or ssss_out-name:OFF:hr.mn.sc
Value: ssss – 4-digit SMS password; hr – hours, range – [00... 23]; mn – minutes, range –
[00... 59]; sc – seconds, range – [00... 59]; out-name – up to 16 characters output name.
Example: 1111_C1:OFF:00.10.15
ONLY FOR ESIM110
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
To instantly turn ON/OFF the output and set its state to ON/OFF when the system starts-up, please refer to the following configuration
methods.
Turn ON output/Set
output start-up state
as ON
SMS
Example: 1111_C1:ON
ONLY FOR ESIM110
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
26
EN
SMS text message content:
ssss_C1:ON or ssss_out-name:ON
Value: ssss – 4-digit SMS password; out-name – up to 16 characters output name.
ESIM110/ESIM120 Manual v.3.1
Turn OFF output/Set
output start-up state
as OFF
SMS
Example: 1111_C1:OFF
ONLY FOR ESIM110
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Turn ON output
for time period
SMS
ONLY FOR ESIM120
SMS text message content:
ssss_Co:ON:hr.mn.sc or ssss_out-name:ON:hr.mn.sc
Value: ssss – 4-digit SMS password; o – output number, range - [1... 2]; hr – hours, range –
[00... 23]; mn – minutes, range – [00... 59]; sc – seconds, range – [00... 59]; out-name – up
to 16 characters output name.
Example: 1111_C2:ON:00.00.09
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Turn OFF output
for time period
SMS text message content:
ssss_C1:OFF or ssss_out-name:OFF
Value: ssss – 4-digit SMS password; out-name – up to 16 characters output name.
SMS
ONLY FOR ESIM120
SMS text message content:
ssss_Co:OFF:hr.mn.sc or ssss_out-name:OFF:hr.mn.sc
Value: ssss – 4-digit SMS password; o – output number, range - [1... 2]; hr – hours, range –
[00... 23]; mn – minutes, range – [00... 59]; sc – seconds, range – [00... 59]; out-name – up
to 16 characters output name.
Example: 1111_C1:OFF:00.11.49
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
To instantly turn ON/OFF the specified output and set its state to ON/OFF when the system starts-up, please refer to the following
configuration methods.
ESIM110/ESIM120 Manual v.3.1
EN
27
Turn ON output/Set
output start-up state
as ON
SMS
Example: 1111_C1:ON
ONLY FOR ESIM120
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Turn OFF output/Set
output start-up state
as OFF
SMS text message content:
ssss_Co:ON or ssss_out-name:ON
Value: ssss – 4-digit SMS password; o – output number, range - [1... 2]; out-name – up to
16 characters output name.
SMS
SMS text message content:
ssss_Co:OFF or ssss_out-name:OFF
Value: ssss – 4-digit SMS password; o – output number, range - [1... 2]; out-name – up to
16 characters output name.
Example: 1111_C2:OFF
ONLY FOR ESIM120
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
NOTE: Output can be turned ON for a determined time period only when it is in OFF state.
NOTE: Output can be turned OFF for a determined time period only when it is in ON state.
NOTE: ELDES Configuration Tool software allows to set only the output start-up state.
NOTE FOR ESIM120: The administrator can control any output by SMS text message regardless of the output assigned to the administrator phone number (see ADMINISTRATOR PHONE NUMBERS).
28
EN
ESIM110/ESIM120 Manual v.3.1
11.4. Output Control Confirmation by Call Back
The system can make a phone call confirming that the output control action has been successfully carried out. Once enabled, every output
control action will be followed by a 5-second (by default) ring to the user/administrator phone number that the output control by free of
charge phone call was initiated from.
By default, output control confirmation by call back is disabled. To enable/disable it, please refer to the following configuration methods.
Enable output control
confirmation by call
back
SMS
Example: 1111_CALLBACK:ON
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Set call back duration
BROWSER
Disable output
control confirmation
by call back
SMS
SMS text message content:
ssss_CALLBACK:OFF
Value: ssss – 4-digit SMS password.
Example: 1111_CALLBACK:OFF
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ESIM110/ESIM120 Manual v.3.1
SMS text message content:
ssss_CALLBACK:ON
Value: ssss – 4-digit SMS password.
EN
29
11.5. Output Control from any Phone Number
By default, the system ignores any incoming calls from a non-preset phone number. To permit/deny output control by free of charge phone
call (see 11. OUTPUT (-S)) from a non-preset phone number, please refer to the following configuration methods.
Enable output control
from any phone
number
SMS
SMS text message content:
ssss_STR:ON
Value: ssss – 4-digit SMS password.
Example: 1111_STR:ON
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Disable output
control from any
phone number
SMS
SMS text message content:
ssss_STR:OFF
Value: ssss – 4-digit SMS password.
Example: 1111_STR:OFF
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
NOTE: The system will accept SMS text messages only from a preset administrator phone number even if output control from any
phone number is enabled.
NOTE FOR ESIM120: Once the output control from any phone number is enabled, a non-preset phone number user will be able to
control output C1 only.
11.6. Automatic Output Control
The system comes equipped with automatic output control in accordance with the assigned scheduler (-s). When one or more schedulers
are assigned, the output will automatically turn ON/OFF on the specified weekdays and time set up in the scheduler. The system allows to
assign up to 8 different schedulers. For more details on how to set up the schedulers, please refer to 12. SCHEDULERS.
Assign scheduler
SMS
Example: 1111_OSCHED1_8:ON
ONLY FOR ESIM110
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
30
EN
SMS text message content:
ssss_OSHED1_c:ON
Value: ssss – 4-digit SMS password; c – scheduler number; range – [1... 8].
ESIM110/ESIM120 Manual v.3.1
Remove scheduler
SMS
Example: 1111_OSCHED1_3:OFF
ONLY FOR ESIM110
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Assign scheduler
SMS
SMS text message content:
ssss_OSHEDo_c:ON
Value: ssss – 4-digit SMS password; o – output number, range [1 – output C1; 2 – output
C2]; c – scheduler number; range – [1... 8].
Example: 1111_OSCHED2_1:ON
ONLY FOR ESIM120
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Remove scheduler
SMS text message content:
ssss_OSHED1_c:OFF
Value: ssss – 4-digit SMS password; c – scheduler number; range – [1... 8].
SMS
SMS text message content:
ssss_OSHEDo_c:OFF
Value: ssss – 4-digit SMS password; o – output number, range [1 – output C1; 2 – output
C2]; c – scheduler number; range – [1... 8].
Example: 1111_OSCHED1_5:OFF
ONLY FOR ESIM120
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ATTENTION: Once the scheduler, set up for automatic output control, comes into effect, the user/administrator will NOT be able to
control the output by phone call and SMS text message.
ATTENTION: If the date and time are not set, the system will NOT be able to manage automatic output control. For more details on how to
set date and time, please refer to 9. DATE AND TIME.
ESIM110/ESIM120 Manual v.3.1
EN
31
12.SCHEDULERS
The system comes equipped with 8 schedulers that allow to set up the day (-s) of the week and time parameters. The schedulers are
used to set up user access restriction (see 10.1. User Validity and Access Restriction) as well as automatic output control (see 11.6.
Automatic Output Control). Each scheduler includes the following parameters:
• Every Day – Determines whether the scheduler will be valid everyday regardless of the current day of the week.
• At Specified Day (-s) – Determines day (-s) in the week when the scheduler is to be valid.
• Start Time – Determines the point in time when the scheduler is to take effect.
• End Time – Determines the point in time when the scheduler is to cease to take effect.
Select At Specified
Day (-s)
SMS
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Enable day (-s) of the
week
SMS
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
SMS
EN
SMS text message content:
ssss_SCHEDc_wd:OFF
Value: ssss – 4-digit SMS password; c – scheduler number; range – [1... 8]; wd – weekday,
range – [MO – Monday; TU – Tuesday; WE – Wednesday; TH – Thursday; FR – Friday; SA –
Saturday; SU – Sunday].
Example: 1111_SCHED4_SU:OFF
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
32
SMS text message content:
ssss_SCHEDc_wd:ON
Value: ssss – 4-digit SMS password; c – scheduler number; range – [1... 8]; wd – weekday,
range – [MO – Monday; TU – Tuesday; WE – Wednesday; TH – Thursday; FR – Friday; SA –
Saturday; SU – Sunday].
Example: 1111_SCHED6_FR:ON
Config
Tool
BROWSER
Disable day (-s) of the
week
SMS text message content:
ssss_SCHEDc_AL:OFF
Value: ssss – 4-digit SMS password; c – scheduler number; range – [1... 8].
Example: 1111_SCHED4_AL:OFF
ESIM110/ESIM120 Manual v.3.1
Set start time
SMS
SMS text message content:
ssss_SCHEDc_st:hr:mn
Value: ssss – 4-digit SMS password; c – scheduler number; hr – hours, range – [00... 23];
mn – minutes, range – [00... 59].
Example: 1111_SCHED2_ST:20:25
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Set end time
SMS
SMS text message content:
ssss_SCHEDc_en:hr:mn
Value: ssss – 4-digit SMS password; c – scheduler number; hr – hours, range – [00... 23];
mn – minutes, range – [00... 59].
Example: 1111_SCHED8_EN:09:12
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Select Every Day
SMS
SMS text message content:
ssss_SCHEDc_AL:ON
Value: ssss – 4-digit SMS password; c – scheduler number, range – [1... 8]
Example: 1111_SCHED1_AL:ON
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
View individual
scheduler parameters
SMS
SMS text message content:
ssss_SCHEDc?
Value: ssss – 4-digit SMS password; c – scheduler number, range – [1... 8]
Example: 1111_SCHED3?
NOTE: Multiple scheduler parameters can be configured by a single SMS text message, Example: 111_SCHED2__MO:ON_FR:OFF_
EN:20:18_TH:OFF_ST:15:25_TU:ON_AL:OFF
ATTENTION: If the date and time are not set, the system will NOT be able to use the schedulers. For more details on how to set date and
time, please refer to 9. DATE AND TIME.
ESIM110/ESIM120 Manual v.3.1
EN
33
13.EVENT LOG
This feature allows to chronologically register up to 1000 timestamped records regarding the following system events:
• Output control including the user/administrator phone number and user name.
• User validity expiry by deadline.
• User validity expiry by ring counter.
• Automatic output control beginning.
• Automatic output control ending.
To export the event log to .log file or clear it, please refer to the following configuration methods.
Export event log
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
By default, when the event log reaches the 1000 record limit, the system will send the notification by SMS text message to the administrator
phone number. To clear the event log and/or disable/enable the notification regarding the full event log, please refer to the following
configuration methods.
Clear event log
SMS
SMS text message content:
ssss_DELETELOG
Value: ssss – 4-digit SMS password.
Example: 1111_DELETELOG
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Disable Log Full
notification
BROWSER
Enable Log Full
notification
BROWSER
34
EN
ESIM110/ESIM120 Manual v.3.1
The event log may be set as of LIFO (last in, first out) type that allows the system to automatically replace the oldest records with the the
latest ones. By default, LIFO type event log is disabled. To enable/disable it, please refer to the following configuration methods.
Enable LIFO type log
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Disable LIFO type log
BROWSER
ESIM110/ESIM120 Manual v.3.1
EN
35
14.INPUTS
The system comes equipped with 3 inputs designed for fault indication output or detection device connection, such as door contacts. Once
a fault indication output and/or a detection device is triggered, the system will send a notification to the administrator phone number.
Typically, the inputs are used to receive notifications regarding jammed gate or gate state. For more details, please refer to 14.1. Input
Names and Alarm Notifications.
Each input’s sensitivity level can be customized by a delay time (by default – 600 milliseconds). If an input is left triggered until the delay
time expires, the input is considered violated.
Set input delay
SMS
SMS text message content:
ssss_Tn:in-delay
Value: ssss – 4-digit SMS password; n – input number, range – [1... 3]; in-delay – input
delay, range – [100... 42000000] milliseconds.
Example: 1111_T3:10500
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
The system allows to view the current input state by the following configuration method.
View input state
SMS
SMS text message content:
ssss_INFO
Value: ssss – 4-digit SMS password;
Example: 1111_INFO
14.1. Input Names and Alarm Notifications
Each input has a name that can be customized. Typically, the name specifies a device type connected to a certain input terminal, for
example: GateOpen. The input names are used in notifications that are sent by SMS text message to the administrator regarding the input
alarm event. By default, the input names are: Z1 – zone1, Z2 – zone2, Z3 – zone3.
Set input name
SMS
SMS text message content:
ssss_Zn:input-name
Value: ssss – 4-digit SMS password; n – input number, range – [1... 3]; input-name – up to
8 characters input name.
Example: 1111_Z2:GateOpen
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
36
EN
ESIM110/ESIM120 Manual v.3.1
View input names
SMS
SMS text message content:
ssss_STATUS
Value: ssss – 4-digit SMS password.
Example: 1111_STATUS
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
By default, the system sends SMS text message to the first available administrator in case of input alarm. If the system did not receive the
SMS delivery report during 20 seconds, it will attempt to send the SMS text message to the next preset administrator phone number. To
ignore the SMS delivery report and allow/disallow the system to send the SMS text message to every preset administrator phone number,
please refer to the following configuration methods.
Enable notification
to all preset
administrator phone
numbers in case of
input alarm
SMS
Example: 1111_SMSALL:ON
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Disable notification
to all preset
administrator phone
numbers in case of
input alarm
SMS text message content:
ssss_SMSALL:ON
Value: ssss – 4-digit SMS password.
SMS
SMS text message content:
ssss_SMSALL:OFF
Value: ssss – 4-digit SMS password.
Example: 1111_SMSALL:OFF
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ATTENTION: Space characters, parameter values, such as ON, OFF etc. are NOT allowed in the input names. Space characters, parameter values, such as ON, OFF etc. are NOT allowed in the input names.
For more details on how to disable the input alarm notifications, please refer to 14.2. Disabling and Enabling Inputs.
For more details on the algorithm of how the system sends the notifications, please refer to 16. SYSTEM NOTIFICATIONS.
ESIM110/ESIM120 Manual v.3.1
EN
37
14.2. Disabling and Enabling Inputs
By default, all inputs are enabled. Once disabled, input alarm event will no longer be followed by an SMS text message. To disable/enable
an individual input, please refer to the following configuration methods.
Disable input
SMS
SMS text message content:
ssss_Zn:OFF
Value: ssss – 4-digit SMS password; n – input number, range – [1... 3]; input-name – up to
8 characters input name.
Example: 1111_Z2:Gate jammed
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Enable input
SMS
SMS text message content:
ssss_Zn:ON
Value: ssss – 4-digit SMS password; n – input number, range – [1... 3]; input-name – up to
8 characters input name.
Example: 1111_Z2:Gate jammed
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
View input status
SMS
SMS text message content:
ssss_STATUS
Value: ssss – 4-digit SMS password.
Example: 1111_STATUS
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
38
EN
ESIM110/ESIM120 Manual v.3.1
15.SYSTEM INFORMATION. INFO SMS
The system supports an informational SMS text message identified as the Info SMS, which can be delivered upon request. Once requested,
the system will reply with Info SMS that provides the following:
• System date & time.
• GSM signal strength.
• Number of occupied and empty slots in the user database.
• State of inputs (OK/alarm).
Request for system
information
SMS
SMS text message content:
ssss_INFO
Value: ssss – 4-digit SMS password.
Example: 1111_INFO
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
For more details on the algorithm of how the system sends the notifications, please refer to 16. SYSTEM NOTIFICATIONS.
15.1. Periodic Info SMS
The system may send the Info SMS to the administrator phone number periodically. The recommende period is once a day at 11:00
(frequency – 1 day; time – 11). The minimum period is every 1 hour (frequency – 0 days; time – 1). Typically, this feature is used to verify
the operation status of the system.
To enable periodic Info SMS by setting the frequency and time or disable it, please refer to the following configuration methods.
Set periodic Info SMS
frequency and time
SMS
SMS text message content:
ssss_INFO:fff:it
Value: ssss – 4-digit SMS password; fff – frequency, range – [00... 99] days; it – time, range
– [01... 23].
Example: 1111_INFO:3.15
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Disable periodic Info
SMS
SMS
SMS text message content:
ssss_INFO:00:00
Value: ssss – 4-digit SMS password.
Example: 1111_INFO:00.00
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
ESIM110/ESIM120 Manual v.3.1
EN
39
16.SYSTEM NOTIFICATIONS
In case of a certain event, the system attempts to send an SMS text message to the first preset administrator phone number only. If the
administrator phone number is unavailable and the system fails to receive the SMS delivery report within 20 seconds, it will attempt to
send the SMS text message to the next preset administrator phone number. The administrator phone number may be unavailable due to
the following reasons:
• mobile phone was switched off.
• was out of GSM signal coverage.
The system will continue sending the SMS text message to the next preset administrator phone numbers in the priority order until one
is available. The system sends the SMS text message only once and will not return to the first administrator phone number if the last one
was unavailable.
16.1. SMSC (Short Message Service Center) Phone Number
An SMS center (SMSC) is a GSM network element, which routes SMS text messages to the destination recipient and stores the SMS text
message if the recipient is unavailable. Typically, the phone number of the SMS center is already stored in the SIM card provided by the GSM
operator. If the administrator fails to receive replies from the system, the SMS center phone number, provided by the GSM operator, must
be set manually.
Set SMSC phone
number
SMS
SMS text message content:
ssss_SMS_+ttteeellnnuumm
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits SMSC phone number.
Example: 1111_SMS_+4417031111111
ATTENTION: Before setting the SMSC phone number, please check the credit balance of the system’s SIM card. The system will fail to
reply if the credit balance is insufficient.
40
EN
ESIM110/ESIM120 Manual v.3.1
17.GPRS NETWORK SETTINGS
The GPRS network settings are used for device communication with the remote configuration server or Smart Gate server via GPRS
connection. To set the GPRS network settings, please refer to the following configuration methods.
Set APN
SMS
SMS text message content:
ssss_SETGPRS:APN:acc-point-name
Value: ssss – 4-digit SMS password; acc-point-name – up to 31 character APN (Access
Point Name) provided by the GSM operator.
Example: 1111_SETGPRS:APN:internet
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Set user name
SMS
SMS text message content:
ssss_SETGPRS:USER:usr-name
Value: ssss – 4-digit SMS password; usr-name – up to 31 character user name provided by
the GSM operator.
Example: 1111_USER:mobileusr
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
Set password
SMS
SMS text message content:
ssss_SETGPRS:PSW:password
Value: ssss – 4-digit SMS password; password – up to 31 character password provided by
the GSM operator.
Example: 1111_SETGPRS:PSW:mobilepsw
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
View GPRS network
settings
SMS
SMS text message content:
ssss_SETGPRS?
Value: ssss – 4-digit SMS password.
Example: 1111_SETGPRS?
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
WEB
This operation may be remotely carried out from the PC using the web browser.
BROWSER
NOTE: Multiple parameters can be set by single SMS text message, Example: 1111_SETGPRS:APN:internet;USER:mobileusr;PSW:mobilepsw
ESIM110/ESIM120 Manual v.3.1
EN
41
18.REMOTE SYSTEM RESTART
In some critical situations, a system restart may be required. To remotely carry out system restart, please refer to the following
configuration method.
Restart the system
SMS
SMS text message content:
ssss_RESTART
Value: ssss – 4-digit SMS password.
Example: 1111_RESTART
42
EN
ESIM110/ESIM120 Manual v.3.1
19.TECHNICAL SUPPORT
19.1. Troubleshooting
Indication
Possible reason
Indicators SIM STAT and NETW are OFF
· No mains power
· Wrong wiring
· Blown fuse
· Disconnected antenna
· Micro-controller could not start due to electrical mains noise or static discharge
Indicator SIM STAT is ON
· Missing SIM card
· PIN code is enabled
· SIM card is inactive
· GSM network fault
Unable to receive any SMS text messages to
the administrator phone number or control the
output
· Insufficient SIM card credit balance
· Caller's phone number is set up as withheld (hidden)
· No GSM network signal
· Wrong administrator/user phone number
· Administrator/user phone number is not set
· SIM card was replaced before disconnecting mains power
· Incorrect SMS center phone number
Unable to connect to the device remotely via
GPRS connection
· GPRS settings (APN, user name, password) not set.
· Insufficient SIM card credit balance
· Mobile internet service (GPRS) not activated on the SIM card.
Received SMS text message “Wrong syntax”
· Incorrect SMS text message structure
· Unnecessary space character might have been typed in SMS text message
For product warranty repair service please , contact your local retail store where this product was purchased.
If your problem could not be fixed by the self-guide above, please contact your local distributor. More up to date information about your
device and other products can be found at the manufacturer’s website www.eldes.lt
19.2.Restoring Default Parameters
1. Power down the device.
2. Short-circuit (connect) the DEF pins.
3. Power up the device for 7 seconds.
4. Power down the device.
5. Remove the short-circuit from DEF pins.
6. Parameters restored to default.
19.3.Updating the Firmware via USB Cable
1. Power down the device.
2. Short-circuit (connect) the DEF pins.
3. Connect the device via USB cable to the PC.
4. Power up the device.
5. The new window must pop-up where you will find the .bin file. Otherwise open My Computer and look for Boot Disk drive.
6. Delete the .bin file found in the drive.
7. Copy the new firmware .bin file to the very same window.
8. Power down the device.
9. Unplug the USB cable.
10. Remove the short-circuit from DEF pins.
11. Power up the device.
12. Firmware updated.
NOTE: It is strongly recommended to restore default parameters after the firmware update.
ESIM110/ESIM120 Manual v.3.1
EN
43
20. RELATED PRODUCTS
ME1 – metal cabinet
Power supply
Adhesive flat GSM antenna
44
EN
EBU1 – power backup unit
IP66 - plastic enclosure
Magnet mount straight GSM antenna
ESIM110/ESIM120 Manual v.3.1
Copyright © “ELDES UAB”, 2013. All rights reserved
It is not allowed to copy and distribute information in this document or pass to a third party without advanced written authorization by “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without
a warning. Hereby, “ELDES UAB” declares that wireless smoke detector EWF1 is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt
ESIM110/ESIM120 Manual v.3.1
EN
45
Made in the European Union
www.eldes.lt
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement