Aqua Systems AQLP Series Specifications

Aqua Systems AQLP Series Specifications
TEST
IDEAL RANGE
ADJUSTMENT REQUIRED
Free Chlorine
1.0 - 3.0 ppm
Turn output dial up to increase,
down to decrease -OR- increase
or decrease pump filtration time.
pH
7.2 - 7.6
Alkalinity
80 - 120 ppm
Salt
Aqua
Logic
Automation and Chlorination
Too high - add muriatic acid
Too low - add soda ash.
Add baking soda to increase.
Add acid as required to decrease.
2700 - 3400 ppm Add salt as required to increase.
Stabilizer
60 - 80 ppm
Add cyanuric acid to increase.
Calcium
200 - 400 ppm
Add calcium to increase.
Drain and add water to decrease.
Electrolytic Cell inspect & clean
Refer to section in manual.
(actuator, cell & remote display not included - order separately)
Operation Manual
for model
AQL-P-4
G
LDLINE
G
C ON TROLS
North Kingstown, RI 02852 USA
092032K
Copyright © 2008 Goldine Controls
LDLINE
C ON TROLS
www.goldlinecontrols.com
888-921-7665
LIMITED WARRANTY Goldline warrants its Aqua Rite, Aqua Rite Pro, Aqua Trol, Aqua Logic and Pro Logic products
(products with Goldline part numbers starting with AQ-RITE-, AQ-RT-PRO, AQ-TROL-, AQ-LOGIC-, AQL-P-, AQL-PS-,
AQL-CL-, PL-P-, PL-PS-, and HPC-2) to be free from defects in material or workmanship, under normal use and service:
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always
be followed, including the following:
•
•
•
•
•
READ AND FOLLOW ALL INSTRUCTIONS
!
WARNING: Disconnect all AC power during installation.
!
WARNING: Water in excess of 100 degrees Fahrenheit may be
hazardous to your health.
!
WARNING: To reduce the risk of injury, do not permit children to
use this product unless they are closely supervised at all times.
A green colored terminal marked “Earth Ground” is located inside the wiring
compartment. To reduce the risk of electric shock, this terminal must be
connected to the grounding means provided in the electric supply service
panel with a continuous copper wire equivalent in size to the circuit
conductors supplying the equipment.
•
One bonding lug for US models (two for Canadian models) is provided on the
external surface. To reduce the risk of electric shock, connect the local
common bonding grid in the area of the swimming pool, spa, or hot tub to
these terminals with an insulated or bare copper conductor not smaller than 8
AWG US / 6 AWG Canada.
•
All field installed metal components such as rails, ladders, drains, or other
similar hardware within 3 meters of the pool, spa or hot tub shall be bonded
to the equipment grounding bus with copper conductors not smaller than
8 AWG US / 6 AWG Canada.
•
SAVE THESE INSTRUCTIONS
For three years from the date of the initial system installation on private, residential swimming pools within the USA or Canada
and one year from the date of initial system installation on commercial installations, installations outside of the USA or Canada
and for any replacement parts or accessory products, provided they are installed in accordance with the Goldline installation
instructions and specifications provided with the product. If written proof of the date of the initial system installation is not
provided to Goldline, the manufacturing datecode on the Aqua Rite, Aqua Rite Pro, Aqua Trol, Aqua Logic and Pro Logic
electronics unit will be the sole determinant of the date of the initial system installation.
For residential installations in USA or Canada: If a product is defective in workmanship or materials and is removed and returned
freight prepaid within three (3) years after the date of the initial system installation, Goldline will, at its option, either repair or
replace the defective product and return it freight prepaid.
For commercial installations, installations outside the USA and Canada, and accessory products and replacement parts: If a
product is defective in workmanship or materials and is removed and returned freight prepaid within one (1) year after the date
of the initial system installation, Goldline will, at its option, either repair or replace the defective product and return it freight
prepaid.
Contact any Goldline dealer or contact Goldline at 61 Whitecap Drive, North Kingstown, RI 02852 for warranty service. The
costs incurred in removal and/or reinstallation of the product are NOT covered under this warranty. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
WARRANTY EXCLUSIONS:
1.
Material supplied or workmanship performed by others in process of installation.
2.
Damage resulting from improper installation including installation on pools larger than the product rating.
3.
Problems resulting from failure to operate the product(s) in accordance with the recommended instructions contained
in product’s owners manual(s).
4.
Problems resulting from failure to maintain pool water chemistry in accordance with the recommendations in the
owners manual(s).
5.
Problems resulting from tampering, accident, abuse, negligence, unauthorized repairs or alternations, fire, flood,
lightning, freezing, external water, degradation of natural stone used in or immediately adjacent to a pool or spa, war
or acts of God.
DISCLAIMER. THE EXPRESS LIMITED WARRANTY ABOVE CONSTITUTES THE ENTIRE WARRANTY OF
GOLDLINE WITH RESPECT TO ITS POOL AUTOMATION AND CHLORINATION PRODUCTS AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. IN NO EVENT SHALL GOLDLINE
BE RESPONSIBLE FOR ANY CONSEQUENTIAL, SPECIAL OR INCIDENTAL DAMAGES OF ANY NATURE
WHATSOEVER, INCLUDING, BUT NOT LIMITED TO, PERSONAL INJURY, PROPERTY DAMAGE, DAMAGE TO
OR LOSS OF EQUIPMENT, LOST PROFITS OR REVENUE, COSTS OF RENTING REPLACEMENTS, AND OTHER
ADDITIONAL EXPENSES, EVEN IF THE SELLER HAD BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OF LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
NO WHOLESALER, AGENT, DEALER, CONTRACTOR OR OTHER PERSON IS AUTHORIZED TO GIVE ANY
WARRANTY ON BEHALF OF GOLDLINE.
THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN ALTERED IN ANY WAY AFTER LEAVING THE FACTORY.
36
Table of Contents
35
System Overview
Block Diagram.......................................................................
Automation.............................................................................
Chlorination............................................................................
Default Display.......................................................................
1
1
2
2
Manual System
Operation
Filter Pump.............................................................................
Lights and Aux Outputs..........................................................
Pool/Spa Valves.....................................................................
Service....................................................................................
3
4
4
4
Automatic System
Operation
(Programming)
Using the Programming Buttons..........................................
Programming Menu Flow Chart...........................................
Settings Menu........................................................................
Timers Menu..........................................................................
Configuration Menu...............................................................
5
6
7
10
13
Quick “How To”
Guide
Operate the Spa - Manually..................................................
Operate the Spa - Automatically..........................................
Set the Heater Temperature.................................................
Set the Chlorinator Output ...................................................
Start/Stop Superchlorination................................................
Program a Timeclock............................................................
Program a Countdown Timer...............................................
Enter/Exit Service Mode.......................................................
22
22
22
22
23
23
23
24
Chlorinator Operation/
Water Chemistry
Saturation Index.....................................................................
Salt Level................................................................................
Type of Salt............................................................................
How to Add or Remove Salt.................................................
25
26
26
26
System Maintenance
Servicing and Cleaning the Turbo Cell................................ 29
Winterizing.............................................................................. 29
Spring Startup........................................................................ 29
Troubleshooting &
Diagnostic Information
Service Mode .......................................................................
Check System Indicator........................................................
Diagnostic Menu...................................................................
Chlorinator Diagnostics........................................................
Instant Salt..............................................................................
Flow Switch............................................................................
Cell, Water, Air, Solar Temperature......................................
Software Revision.................................................................
Warranty
Aqua Logic Warranty............................................................. 36
30
31
32
32
32
32
33
33
System Overview
The following statement is applicable if any of the wireless accessories are connected to the Aqua Logic
system.
The Aqua Logic is a multifunction pool controller used to fully manage your pool/spa system. The Aqua
Logic can control pumps, valves, lighting, heaters, and chlorination. Although the Aqua Logic is easy to
use, it is important to completely read through this operating manual before attempting to operate the
control.
FCC Statement
(Compliance Statement, Part 15.19): This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
WARNING (Part 15.21): Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Optional
Wireless Base
Receiver
Industry Canada Statement
Optional
Remote Display
Keypad
The term “IC” before the certification/registration number only signifies that the Industry Canada technical
specifications were met.
Main Display
Keypad
Interference
(maximum of three)
Filter Pump
Lights
Aux 1
Water
Temperature
Sensors
120/240V
Relays
Aux 2
Pool/Spa Suction &
Return Valves
Air
Solar
24V Valve
Actuators
Valve 3
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, then the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into a power source on different circuit than the receiver.
Consult the dealer or an experienced radio/TV technician for help.
Heater
Optional
Flow Switch
Optional
Chlorinator Cell
240 VAC
Power
Circuit Breaker
Subpanel
NOTE: This manual assumes that the Aqua Logic has been wired and configured according to the Installation Manual. Aspects of the Aqua Logic that pertain to system setup are not covered in this manual.
Automation
The AQL-P-4 can control up to 4 high voltage (120/240V) pieces of equipment, up to 3 automatic valve
actuators, and a conventional and solar heater. Both manual and automatic (programmed) operation are
available. All of the control functions can be programmed at a display/keypad which is part of the main unit
(typically located near the pool equipment) or at one or more remote display/keypads.
1
34
+
>
Solar Sensor
Short circuit
+
>
Air Sensor
94ºF
+
>
Water Sensor
Open circuit
+
>
Cell Temp Sensor
77ºF
>
No function
Move to previous/next menu item
>
No function
Move to previous/next menu item
>
No function
Move to previous/next menu item
>
No function
Move to previous/next menu item
Available displays depend on configuration. If the sensor appears to operating properly,
then the temperature will be displayed. If this temperature is not correct then check the
placement of the sensor. If the problem is not placement related, then the sensor will, most
likely, require replacement. If the display is “Open Circuit” or “Short Circuit” then check the
wiring to the sensor and also make sure that the wires are secure in the terminal block in the
Aqua Logic main unit.
+
>
>
No function
Move to previous/next menu item
>
No function
Move to previous/next menu item
>
No function
Move to previous/next menu item
>
No function
Move to previous/next menu item
Available displays depend on configuration. If you call the Goldline Technical Service
Department for assistance, they may ask for the software revisions of both the main unit and
each of the display/keypads or other devices that are attached to the system. Note that it is
possible that different display/keypads have different software revision levels. For this
reason, it is advisable to check this diagnostic menu item on every display.
With the use of the optional AQL-CL chlorination kit, the Aqua Logic is also an automatic chlorine generation system for pool and/or spa sanitization. If enabled (see Configuration Menu), this operation requires
a low concentration of salt (sodium chloride) in the pool/spa water. The Aqua Logic automatically converts the salt into free chlorine which kills bacteria and algae in the pool/spa. Chlorine will revert back to
sodium chloride after killing bacteria. These reactions will continuously recycle, virtually eliminating the
need to add sanitizing chemicals to your pool/spa. The only time you may need to add more salt to the
pool/spa is when water is replenished due to backwashing, draining, or splashing (not evaporation).
The Aqua Logic is designed to handle the purification needs of most residential swimming pools up to
40,000 gallons (150,000 liters), or the needs of most commercial pools up to 25,000 gallons (95,000
liters). Check local codes for other restrictions. The actual amount of chlorination required to properly
sanitize a pool varies due to bather load, rainfall, temperature, and the pool’s cleanliness.
For pools larger than 40,000 gallons, the Aqua Logic can control one or more Goldline Aqua Rite chlorinators to supplement chlorine production.
NOTE: Before installing this product as part of a saline water purification system in a pool or spa using
natural stone for coping or for immediately adjacent patios/decking, a qualified stone installation specialist
should be consulted regarding the appropriate type, installation, sealant (if any) and maintenance of stone
used around a saline pool with electronic chlorine generator in your particular location and circumstances.
Default Display
Turn power on at the main panel and turn the Aqua Logic control power circuit breaker on. The keypad
will show the default display. The default display alternates between the day/time, air and pool (or spa)
temperature, pool/spa sanitizer setting, and salt level. Under certain circumstances, additional displays
may be added to the default menu to inform you about system operation. Refer to the Programming Menu
Flowchart on page 6 to view all possible displays. The Aqua Logic will automatically scroll through all of
the available default menu displays or you can press “<” or “>” to manually scroll.
Saturday
11:45A
Pool/Spa
+
Service
>
6B Spa Software
Remote A r1.00
+
>
RF Base Software
r1.20 ID:1234
+
>
Display Software
remote-08 r3.10
+
>
Main Software
Revision 2.40
Chlorination
33
Menu
Filter
Lights
Aux 1
Aux 2
>
2
Diagnostic Menu
+23.45
Set Day and
+6.75A
Time
Wednesday
84°F
3200PPM
10:37P
(Pool/Spa/Spillover)
Filter Pump
Filter
Check System
Indicator
If the current (amps) display is 0.00A, then the chlorinator is operating normally but is in the
off part of its normal operating cycle. Simply press either the “+” or “-“ key to start a new
cycle.
(On/Off)
Pool/Spa
Lights
The Aqua Logic periodically reverses the polarity of the voltage applied to the cell in order
to automatically clean off any calcium deposits. It is important that you check the chlorinator
operation in both polarities. To do this, press either the “+” or “-“ buttons and the chlorinator
will turn off, wait for 15 seconds and then turn on in the opposite polarity.
(On/Off)
Lights
Service
Aux 1
Aux 2
Service Button
Aux 1
(On/Off)
If a conventional or solar heater is operating, it is likely that the temperature of the water at
the cell is higher than the pool/spa water temperature displayed on the Aqua Logic default
display.
Aux 2
(On/Off)
(main display only)
Filter Pump
Single Speed Filter Pump: If the pump is currently off, press the FILTER button to turn on the pump.
Pressing the FILTER button again will turn off the pump. However, if there is a heater in the system, and
it is operating, and the “Heater Cooldown” feature is enabled (Configuration Menu) then: when you press
the FILTER button to turn off the filter, only the heater will turn off, the Filter LED will flash and the display
will indicate “Heater Cooldown”. At this point the filter pump will automatically turn off after 5 minutes of
heater cooldown operation. If you want to override the heater cooldown, simply press the FILTER button
again to turn off the filter pump.
Two Speed Filter Pump: If the pump is currently off, simply press the FILTER button to turn on high
speed operation of the filter pump. The “Filter” LED will illuminate continuously. Pressing the FILTER
button again will switch to low speed operation and the “Filter” LED will flash. If you attempt to switch to
low speed shortly after turning on high speed the filter pump will automatically remain in high speed for 3
minutes before switching to low speed to allow the pump to prime and establish normal water flow.
Freeze Protection: This function protects the pool, plumbing, and equipment against freeze damage. If
Freeze Protection is enabled and the AIR temperature sensor falls below the preset freeze protection
temperature (see Filter Pump Configuration), the Aqua Logic will turn on the filter pump to circulate the
water.
3
Instant Salt
3200 PPM (+=save)
+
>
Press to load the “Instant salt” into the averaged salt display
Move to previous/next menu item
This display will be shown only if the chlorinator is enabled. This display shows “Instant
Salt” or “Instant Minerals” (if Chlor. Config. is set for “Display Minerals”). The “Instant
Salt” is calculated based on the voltage, current (amps), and water temperature at the cell.
This is different than the “average salt” value which is displayed as part of the default menu.
There are a number of reasons why instant and average salt readings may differ. Some of
these include salt having just been added to the pool and not yet thoroughly mixed, calcium
buildup on the cell, and the cell aging.
Flow Switch
Flow
+
>
Valve 3
Indicator
Press to switch chlorinator operation to opposite polarity (15 second delay)
Move to previous/next menu item
This display will be shown only if the chlorinator is enabled. For the chlorinator to be
operating, several other things must be happening: the filter pump must be running, the flow
switch must be detecting flow, the chlorinator setting must be set greater than 0%, the water
temperature at the cell must be between 50ºF and 140ºF, and the salt level must be within the
operating range. If any of these conditions are not met, the chlorinator diagnostic display
will tell you the reason. It’s possible to have more than one reason, in which case after you
rectify what was displayed the first time, a second display will appear.
Pool/Spa Button
Salt Level
3200ppm
>
+/- 23.45V is the voltage applied to the chlorinator cell
+/-6.75A is the current (amps) through the cell
84ºF is the water temperature at the cell
3200PPM is the “instant” salt level at this time
Display
Heater Indicator
+
>
While the main objective of the Aqua Logic is to automate the operation of your pool/spa system, there
may be certain times when you want to override the automatic operation and control the equipment manually. To operate the pool equipment manually while keeping the automation active, perform the following
procedures. Note that if you turn a relay on manually, it will remain on until either you turn it off manually,
or the next time the programmed automatic operation would normally turn that relay off. Example: the
filter pump is programmed to run from 9:00A to 5:00P daily. If you turn the filter pump on manually at
8:00PM, it will run continuously until the next day at 5:00PM at which time it will turn off and follow the
normal program from then on. Manually turning off a relay works in a similar fashion.
To enter the Diagnostic Menu, press the “Menu” button repeatedly until the display shows “Diagnostic
Menu”. At this point, you can use either the “<” or “>” buttons to scroll through the various menu items
which are described below:
>
Manual System Operation
>
No function
Move to previous/next menu item
This display will be shown only if the chlorinator is enabled. The current status of the flow
switch is displayed. There is a short delay when transitioning from flow to no-flow and a
longer delay on the transition from no-flow to flow. The delay time is displayed.
32
Lights, Aux1 and Aux2 Outputs
Check System Indicator
The “CHECK SYSTEM” LED will alert you when the Aqua Logic detects any of the following conditions
that are abnormal and require attention for optimal operation of your pool.
• Inspect Cell -- for optimum operation, you will need to inspect the Aqua Logic chlorinator cell approximately every 3 months and clean the cell if necessary. The Aqua Logic will automatically remind
you when it is time and display “Inspect Cell, + to reset” as part of the rotating Default Menu. Clean the
cell (see instructions, page 29) and then press the “+” button during the “Inspect Cell” display to reset
the timer.
• Low Salt/Minerals or Very Low Salt/Minerals -- when the salt is too low the Aqua Logic will
generate less chlorine and the life of the cell is degraded. Check the cell and clean if necessary (see
instructions, page 29) before adding salt (see instructions, page 26).
• High Salt/Amps/Minerals -- the Aqua Logic will stop generating chlorine under certain high salt
conditions in order to protect the internal electronics from damage. The only way to lower the salt level
is to partially drain the pool and add fresh water.
Standard Relay: Manual operation of all 3 relays is identical. Assuming that the relay is currently off,
simply press the appropriate button to turn on the relay. If the relay does not turn on, it probably is due to
the “interlock” feature (which was set up in the Configuration Menu) being activated that requires the filter
pump to be running and the valves to be in the pool-only position. This protects pumps and other equipment from possible damage. If the controlled output is on, pressing the appropriate button again will turn
off the relay. Manual turn off is disabled if the “Freeze Protection” feature is enabled and the air temperature is less than the selected freeze temperature threshold.
Dimmer Relay: If Lights or an Aux output is configured as a dimmer, pressing the corresponding button
will generate a temporary display which shows the dimmer output level (Off - On 100%). Pushing the “+”
or “-” button changes the level in increments of 20%. When the desired output level is displayed, press the
corresponding button again to turn off the display and return to normal operation. When the Lights or Aux
output comes on again (either manually or automatically), the dimmer output level will be the same as the
last time that it was set.
Pool/Spa Valves
• Water Sensor -- if the water sensor is either an open or short circuit.
Pool-only or spa-only systems: The POOL/SPA button has no function.
• Air sensor -- if the freeze protection feature is enabled (Configuration Menu/ Filter Config.) and the air
sensor is either an open or short circuit.
Pool and Spa systems without spa spillover: In pool-only mode, the left LED next to the POOL/SPA
button is illuminated. Pressing the POOL/SPA button will switch the AQL-P-4 to spa-only operation
(right LED illuminated). Pressing the POOL/SPA button again will switch back to pool-only. Note that
the filter pump will turn off while the pool/spa valves are turning.
• Solar Sensor -- if the solar sensor is either an open or short circuit.
• Chlorinator Cell Sensor -- if the chlorinator function is enabled (Configuration Menu/Chlorinator)
and the cell sensor is either an open or short circuit.
• Low Volts -- if the chlorinator cell voltage is too low.
• No Cell Power -- if no chlorinator cell power is detected on the printed circuit board.
• Check Flow Switch -- if the flow switch input is invalid.
• Cell Power Error -- if a chlorinator cell power error is detected on the printed circuit board.
• Cell Missing -- if the chlorinator is enabled but no cell is detected.
For helpful troubleshooting information on any of these issues, go to the Diagnostic Menu and then scroll
through the various items until you see the cause for the “CHECK SYSTEM” LED being illuminated.
Pool and Spa systems with spa spillover: In pool-only mode, the left LED next to the POOL/SPA
button is illuminated. Pressing the POOL/SPA button will switch the AQL-P-4 to spa-only operation
(right LED illuminated). Pressing the POOL/SPA button again will switch to spa spillover operation (both
LED’s illuminated). Pressing the POOL/SPA button again will switch back to pool-only. Note that the
filter pump will turn off while the pool/spa valves are turning.
Service
The main unit keypad has a SERVICE key. This button is used primarily during servicing of the pool
equipment. If you want to completely disable the automatic operation and operate the system manually,
you can put the system into Service or Service-Timed mode by pressing the SERVICE button. Pressing
the SERVICE button once will switch the system into service mode which means that all automatic functions are disabled, and the remote display/keypads are disabled (except for manual turn off for emergencies). The red SERVICE LED will be illuminated and the Aqua Logic will remain in this mode of operation
until manually taken out of service mode.
Pressing the SERVICE button again will cause the Aqua Logic to switch to service-timed mode which is
very similar to service mode, except that the Aqua Logic will automatically return to normal operation after
3 hours. During service timed operation, the “Service” LED will flash and the time remaining will be
displayed on the remote display/keypad(s).
Pressing the SERVICE button again, will return the Aqua Logic to normal (automatic) operation. See
Troubleshooting/Diagnostic Information (page 30) for more information about the service modes.
31
4
Automatic System Operation
The Aqua Logic controls most of your pool equipment automatically in order to minimize the time spent
working on your pool. Most of the pool equipment can be programmed to operate on a timeclock basis.
In addition, the desired pool and spa temperatures and pool and spa chlorinator settings can be programmed. This section will guide you on how to program the automatic operation for each function.
The programming of automatic functions can be performed at either the main display/keypad located at the
pool equipment pad or the in-home remote display/keypad.
Using the programming buttons
There are 5 buttons on each keypad that are used for programming (refer to diagram).
Display
Troubleshooting and Diagnostic Information
The Aqua Logic provides 2 different tools to aid in troubleshooting any problems that may occur in your
pool and/or spa system. The Service mode will allow you to disable automatic operation and manually
control most of the equipment (the heater and general purpose Valve3 output are the exceptions). The
Diagnostic Menu will provide some detailed information regarding system operation.
While both of the features are primarily intended for the use of the professional service technician, their
function is fully explained below. If you believe your system is not operating properly or have questions
regarding the operation, call the Goldline Technical Service Department from Monday through Friday,
8AM to 8PM EST at 888-921-7665.
Service Mode
The main unit keypad has a SERVICE button that is used primarily during servicing of the pool equipment.
If you want to completely disable the automatic operation and operate the system manually, you can put
the system into Service or Service-Timed mode by pressing the “Service” button. Pressing the “SERVICE” button once will switch the system into service mode which means that all automatic functions are
disabled, the optional remote display/keypads are disabled (except for manual turn off for emergencies).
The outputs can be manually controlled by pressing the buttons on the local display/keypad. The red
“SERVICE” LED will be illuminated and the Aqua Logic will remain in this mode of operation until manually taken out of service mode.
Settings
Menu
Menu Button
Select Desired Menu
+
Pressing the “SERVICE” button again will cause the Aqua Logic to switch to service-timed mode which is
very similar to service mode, except that the Aqua Logic will automatically return to normal operation after
3 hours. During service timed operation, the “SERVICE” LED will flash and the time remaining will be
displayed on the remote display/keypad(s).
>
Menu
>
“<” and “>” Buttons
Select Items from
a Menu
“+” and “-” Buttons
Adust
Pressing the “SERVICE” button again, will return the Aqua Logic to normal (automatic) operation.
There are 4 steps to programming any function:
1.
Menu
Press the “MENU” button to get to the desired menu. Multiple pushes of the
button will rotate through all 5 menus and return to the starting point.
2.
>
>
Press either key to scroll through the various items in the selected menu. Multiple
pushes of the button will rotate through all menu items and return to the starting
point. Only menu items that are applicable to your pool will appear. (Example: if
you don’t have a spa, then no spa related menu items will appear).
3.
+
>
4.
Once a menu item has been selected above, the current setting/selection will appear (flashing) on the display. Use the “+” and/or “-” keys to change this selection. Sometimes “+” and “-“ will adjust a value up or down (example: heater
temperature setting or timeclock on/off time). In this case, pushing the “+” or “-”
will change the value by one increment and holding the “+” or “-” button in for
more than one second will make the values auto scroll. In other cases, the “+” and
“-“ may toggle between 2 options (example: turning superchlorination ON or
OFF).
>
Menu
After you have adjusted the item to the desired value, simply move on to the next
menu item to “lock in” your new setting. The Aqua Logic memory will maintain
the setting, even if power is removed for an extended period.
5
30
System Maintenance
To maintain maximum performance, it is recommended that you open and visually inspect the cell every 3
months or after cleaning your filter. The Aqua Logic will remind you to do this by displaying the message
“Inspect/Clean Cell” after approximately 500 hours of operation.
Programming Menu Flowchart
The Aqua Logic’s five menus have many items in each menu that allow you to customize the operation of
your pool/spa equipment. The chart below shows the Aqua Logic’s five menus as well as each menu’s
specific settings
The Aqua Logic electrolytic cell has a self cleaning feature incorporated into the electronic control’s logic.
In most cases this self cleaning action will keep the cell working at optimum efficiency. In areas where
water is hard (high mineral content) or in pools where the water chemistry has been allowed to get “out of
balance”, the cell may require periodic cleaning.
denotes conditional items
Servicing and Cleaning the Turbo Cell
Turn off power to the Aqua Logic before removing the electrolytic cell. Once removed, look inside the cell
and inspect for scale formation (light colored crusty or flaky deposits) on the plates and for any debris
which has passed through the filter and caught on the plates. If no deposits are visible, reinstall. If deposits
are seen, use a high pressure garden hose and try to flush the scale off. If this is not successful, use a plastic
or wood tool (do not use metal as this will scratch the coating off the plates) and scrape deposits off of
plates. Note that a buildup on the cell indicates that there is an unusually high calcium level in the pool (old
pool water is usually the cause). If this is not corrected, you may to have to periodically clean the cell. The
simplest way to avoid this is to bring the pool chemistry to the recommended levels as specified.
Mild Acid Washing: Use only in severe cases where flushing and scraping will not remove the majority
of deposits. To acid wash, turn off power to Aqua Logic. Remove cell from piping. In a clean plastic
container, mix a 2:1 solution of water to muriatic acid (one gallon of water to two quarts of muriatic acid).
ALWAYS ADD ACID TO WATER - NEVER ADD WATER TO ACID. Be sure to wear rubber gloves
and appropriate eye protection. The level of the solution in the container should just reach the top of the
cell so that the wire harness compartment is NOT submerged. It may be helpful to coil the wiring before
immersing the cell. The cell should soak for a few minutes and then rinse with a high pressure garden hose.
If any deposits are still visible, repeat soaking and rinsing. Replace cell and inspect again periodically.
PS-4 only
Winterizing
The Aqua Logic electrolytic cell and flow detection switch will be damaged by freezing water just as your
pool plumbing would. In areas of the country which experience severe or extended periods of freezing
temperatures, be sure to drain all water from the pump, filter, and supply and return lines before any
freezing conditions occur. The electronic control is capable of withstanding any winter weather and should
not be removed.
If you are in an area that only experiences occasional freezing conditions, your Aqua Logic system may be
set up to circulate the pool water whenever the air sensor drops to the selected freeze temperature threshold. Make sure the air sensor is recording the correct temperature and is NOT located in the direct
sunlight to ensure proper freeze protection operation.
Spring Start-up
When first starting the pool in the spring time, it is highly recommended that you temporarily set the pool
and spa chlorinator settings (Pool Sanitizer & Spa Sanitizer in the Settings Menu) to 0% (off) and then
manually shock the pool with any chlorine based shock product and balance the pool water chemistry per
the levels indicated in the Chlorinator Operation section (page 25). Make sure to check the salt and
stabilizer levels and bring them up to the recommended levels. Your local Authorized Aqua Dealer or pool
store can recommend the best chemical treatment for your pool. After the water is clear and balanced,
then go back and adjust the pool and spa chlorinator settings to the appropriate levels. Test the pool
chlorine level weekly and adjust the chlorinator settings up or down accordingly.
It is usually a good idea to also inspect the cell and clean if necessary at the start of the season. See
instructions above.
29
PS-4 only
6
7
1.8
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
80 ppm
(1.5)
3.3
3.2
(1.4)
(1.3)
3.0
2.8
(1.3)
(1.2)
2.7
2.5
(1.2)
(1.1)
2.3
2.2
2.0
(1.0)
(.77)
1.7
1.5
(.68)
(.64)
1.4
1.2
(.54)
0.8
(.54)
0.7
70 ppm
(.45)
1.0
(.82)
(.91)
(2.0)
(1.8)
(1.7)
(1.5)
(1.4)
(1.2)
(1.1)
(.91)
(1.1)
(.91)
(.45)
6.7
(3.0)
(2.6)
(2.4)
(2.3)
(2.1)
4.3
4.0
4.7
(3.2)
(2.9)
(2.7)
3.7
(2.5)
(2.3)
3.3
3.0
(2.0)
(1.8)
2.7
2.3
(1.6)
1.7
1.3
(1.4)
(1.6)
(1.4)
60 ppm
2.5
2.0
2.0
6.0
(3.6)
(3.3)
5.5
5.0
(3.0)
4.5
(2.7)
(2.4)
4.0
3.5
(2.1)
(2.1)
(1.8)
3.0
(1.8)
(2.8)
(4.5)
6.3
(4.3)
(4.1)
5.7
(3.9)
(3.4)
5.3
(3.6)
8.5
(4.8)
8.0
7.5
7.0
6.5
(4.5)
(4.2)
(3.9)
5.0
10.0
(6.0)
(5.7)
9.5
9.0
(5.4)
(6.3)
(6.0)
10.7
10.0
(5.6)
(5.2)
9.3
8.7
(4.9)
(4.5)
8.0
7.4
(4.2)
(3.8)
6.7
6.0
(3.4)
(3.0)
5.4
4.7
(2.7)
3.3
4.0
(2.3)
(2.7)
2.7
40 ppm
4.0
4.2
(2.3)
5.0
3.3
30 ppm
28
50 ppm
(7.5)
13.3
12.7
(7.1)
(6.7)
12.0
(9.0)
16.7
15.8
14.2
13.3
12.5
11.7
10.8
10.0
9.2
8.4
7.5
6.7
5.9
(7.2)
16.0
(6.8)
15.0
(6.4)
14.0
(5.9)
13.0
(5.4)
12.0
(5.0)
11.0
(4.5)
10.0
9.0
(2.2)
8.0
(3.6)
7.0
(3.2)
6.0
(2.7)
(2.7)
20 ppm
5.8
(3.7)
15.0
20.0
(8.6)
19.0
(8.1)
18.0
(10.5)
23.3
22.2
(10.0)
(9.5)
21.0
19.8
(9.0)
(8.5)
18.7
17.2
(8.0)
(7.4)
16.4
15.2
(6.9)
(6.4)
14.0
12.9
(5.9)
(5.3)
11.7
10.5
9.4
(4.3)
7.0
(3.2)
8.2
(3.7)
(4.8)
26.7
(12.0)
25.3
(11.5)
22.7
(10.3)
(9.7)
21.3
(9.1)
20.0
(8.5)
18.7
(7.3)
16.0
(6.7)
14.7
(6.1)
13.4
(4.9)
(5.4)
12.0
10.7
9.4
4.7
The spa solar setting will only appear if the system has been setup for “spa only” or “pool
and spa” operation and the solar control is enabled. The solar system will turn on whenever
the pool/spa valves are in the “spa only” position and the filter pump is running and the spa
water temperature is less than the desired temperature setting and solar heat is available.
(3.2)
>
Adjust the desired spa temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off)
Move to previous/next menu item
10 ppm
+
>
Spa Solar
104°F
(4.3)
The pool heater setting will only appear if the system has been setup for “pool only” or “pool
and spa” operation and the heater control is enabled. The heater will turn on whenever the
pool/spa valves are in the “pool only” or “spa spillover” position and the filter pump is
running and the pool water temperature is less than the desired temperature setting. If you
have both solar heat and a conventional heater and the solar priority option is selected
(Configuration Menu), then the conventional heater will only operate when solar heat is
NOT available.
8.0
>
Adjust the desired pool temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off)
Move to previous/next menu item
(3.6)
+
>
Pool Heater1
Off
6.7
The spa heater setting will only appear if the system has been setup for “spa only” or “pool
and spa” operation and the heater control is enabled. The heater will turn on whenever the
pool/spa valves are in the “spa only” position and the filter pump is running and the spa
water temperature is less than the desired temperature setting. If you have both solar heat
and a conventional heater and the solar priority option is selected (Configuration Menu),
then the conventional heater will only operate when solar heat is NOT available.
(4.3)
>
Adjust the desired spa temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off)
Move to previous/next menu item
5.3
+
>
Spa Heater1
102°F
(3.6)
The Settings Menu allows you to set all system operating parameters except the timeclock and countdown
timers which are part of the Timers Menu.
POUNDS and (Kg) OF STABILIZER (CYANURIC ACID) NEEDED FOR 80 PPM
Settings Menu
0 ppm
The “Diagnostic Menu” is primarily intended for the service technician and contains information and details
about the system operation that are helpful in troubleshooting, if problems occur.
Gallons and (Liters) of Pool/Spa water
The Settings Menu and the Timers Menu are the menus you will be using most often to adjust the operation
of your pool. The Configuration Menu is used when the system is installed and defines what equipment is
connected to each output and the operational logic that will control the equipment. This menu is normally
“locked” and should only be used by a pool professional. Details regarding the Configuration menu are
included in both the Operation and the Installation Manual.
Current
8,000 10,000 12,000 14,000 16,000 18,000 20,000 22,000 24,000 26,000 28,000 30,000 32,000 34,000 36,000 38,000 40,000
Stabilizer
Level (ppm) (30000) (37500) (45000) (52500) (60000) (67500) (75000) (82500) (90000) (97500) (105000) (112500)(120000) (127500)(135000) (142500) (150000)
The Default Menu is a series of informative displays (temperatures, salt levels, chlorinator settings, etc.)
with nothing to set. The Aqua Logic will automatically switch to the default menu when no keys have been
pressed for 2 minutes and will then scroll through each display.
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
3600+
>
Turn super chlorinate on or off
Move to previous/next menu item
This setting will only appear if “chlorinator” is enabled. When you have an unusually high
bather load, a large amount of rain, a cloudy water condition, or any other condition that
requires a large amount of chlorine to be introduced to the pool, activate the Aqua Logic
Super-Chlorinate function. The Aqua Logic will turn on the filter pump, set the pool/spa
valves to the correct position, and set the chlorine generator to maximum output. The
superchlorinate function will continue for the programmed number of hours (see Timers/
Super Chlorinate Hours below) overriding the normal filter pump timeclock settings. At the
end of the super chlorinate period, the pool will return to normal operation.
Dilute
Dilute
Dilute
OK
OK
OK
OK
OK
OK
OK
OK
OK
Dilute
OK
3400
OK
OK
OK
OK
Ideal
Ideal
Ideal
Ideal
Ideal
Ideal
Ideal
Ideal
3200
(12)
(11)
(9)
(8)
(6)
3000
Ideal
(15)
(14)
OK
OK
OK
Ideal
Ideal
Ideal
Ideal
Ideal
Ideal
Ideal
(24)
(23)
(21)
(20)
(18)
47
(17)
(42)
(39)
43
(36)
40
33
(33)
37
(30)
(27)
30
27
(24)
(21)
23
17
13
20
(18)
(15)
(12)
2800
Ideal
67
(30)
(29)
(26)
(27)
63
(60)
(57)
60
50
57
(48)
53
(45)
(51)
(54)
(90)
127
120
113
107
100
93
87
80
73
67
60
47
33
27
40
53
(45)
90
80
(36)
(32)
(23)
2600
50
40
(18)
60
(27)
93
80
(36)
67
(30)
53
(24)
2400
(41)
(50)
110
100
(55)
120
(59)
(64)
140
130
(68)
(73)
160
150
(77)
170
(81)
(86)
190
180
133
200
(123)
267
(117)
253
(110)
240
187
(42)
(48)
107
(55)
(61)
(67)
147
133
120
(73)
160
(79)
(85)
173
(91)
(98)
213
200
227
(104)
(144)
(121)
233
167
83
(38)
2200
(30)
67
100
(45)
(53)
117
133
(61)
150
(83)
183
(76)
(68)
(91)
200
(98)
(106)
217
250
267
(114)
283
(129)
(137)
333
(152)
400
340
320
(145)
300
(136)
280
(127)
240
(91)
220
200
(82)
(73)
(64)
140
(45)
120
100
80
2000
(36)
(55)
160
180
(100)
(109)
260
(169)
(118)
397
(180)
373
350
(159)
327
(148)
303
(117)
233
(106)
(95)
(85)
(74)
163
(53)
140
117
93
1800
(42)
(64)
187
210
257
280
(127)
(138)
453
(207)
427
(195)
400
(182)
373
(170)
347
320
293
(133)
267
(121)
240
(97)
(85)
187
(61)
160
133
(48)
1600
107
(73)
213
(109)
(145)
(158)
510
(232)
480
(218)
450
(205)
420
(191)
390
330
(150)
300
(136)
270
(109)
(95)
210
180
(82)
(68)
150
120
1400
(55)
240
(123)
360
(164)
(177)
567
(258)
533
(243)
500
(227)
467
(212)
433
400
367
(167)
333
(152)
267
300
(106)
233
(76)
(91)
167
(61)
1200
133
200
(121)
(136)
(182)
(197)
623
(283)
587
(267)
550
513
(233)
477
440
403
(183)
367
(167)
330
(117)
293
257
(83)
220
183
(67)
1000
147
(100)
(133)
(150)
(200)
(217)
(250)
(154)
317
467
(211)
443
(201)
420
(190)
300
533
(243)
507
(231)
480
(219)
(181)
600
(263)
570
(259)
540
(246)
380
667
(304)
633
(289)
600
(274)
(172)
733
(333)
697
(317)
660
(300)
360
800
(364)
760
(346)
720
(328)
680
(310)
640
(291)
600
(273)
560
(255)
520
(236)
480
440
(200)
400
(182)
360
320
280
(127)
240
200
(91)
(73)
800
160
(109)
(145)
(164)
(218)
607
(276)
563
(256)
520
477
(217)
433
(197)
390
347
303
(138)
(118)
217
(98)
173
600
(79)
260
(158)
(177)
(236)
(297)
(276)
(127)
(106)
400
(85)
(148)
(170)
(233)
(212)
(191)
(255)
653
607
560
513
467
420
373
327
280
233
187
(163)
867
(398)
823
(378)
780
(358)
693
(317)
650
(297)
737
(339)
(318)
(337)
(403)
(382)
933
(424)
887
840
(360)
(430)
(408)
747
700
793
(363)
(318)
(250)
(227)
(182)
(159)
(136)
(114)
200
(91)
350
250
200
300
400
550
500
450
(205)
(273)
(295)
800
700
600
650
750
(341)
(385)
(453)
(484)
950
900
850
1000
1067
(460)
960
(436)
907
(412)
854
(388)
800
(364)
747
(339)
693
(315)
640
(291)
587
(267)
(242)
480
(218)
427
(194)
373
(97)
(170)
320
(145)
267
(121)
213
0
8,000 10,000 12,000 14,000 16,000 18,000 20,000 22,000 24,000 26,000 28,000 30,000 32,000 34,000 36,000 38,000 40,000
(30,000) (37,500) (45000) (52,500) (60,000) (67,500) (75,000) (82,500) (90,000) (97,500) (105,000) (112,500)(120,000)(127,500)(135,000)(142,500)(150,000)
ppm
+
If you manually turn off the filter pump (using the “Filter” button on any display/keypad),
the super chlorinate function terminates. When you turn the filter pump back on, super
chlorinate will resume for the balance of the programmed number of hours.
Spa Chlorinator
3%
+
>
Adjust the desired chlorinator output for spa (0,1,2,3...9,10,15,20...95,100%)
Move to previous/next menu item
This setting will appear only if the system has been setup for “chlorinator” and “spa only”
or “pool and spa”. It will determine the chlorinator output when the system is operating in
spa-only mode. The actual amount of chlorine introduced into the spa is determined by: this
setting, the amount of time the pool operates in spa-only mode, the water temperature, and
the amount of salt in the water. If the filter pump is running due to the freeze protection
feature, then the chlorinator will not operate during this time.
Pool Chlorinator
60%
+
>
POUNDS and (Kg) OF SALT NEEDED FOR 3200 PPM
Gallons and (Liters) of Pool/Spa water
Super Chlorinate
On
>
Current salt
level
>
Adjust the desired pool temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off)
Move to previous/next menu item
The pool solar setting will only appear if the system has been setup for “pool only” or “pool
and spa” operation and the solar control is enabled. The solar system will turn on whenever
the pool/spa valves are in the “pool only” or “spa spillover” position and the filter pump is
running and the pool water temperature is less than the desired temperature setting and solar
heat is available.
>
27
+
>
Pool Solar
88°F
>
Adjust the desired chlorinator output for pool (0,1,2,3...9,10,15,20...95,100%)
Move to previous/next menu item
This setting will appear only if the system has been setup for “pool only” or “pool and spa”.
It will determine the chlorinator output when the system is operating in pool-only or spa
spillover modes. The actual amount of chlorine introduced into the pool is determined by:
this setting, the amount of time the filter pump is running, the water temperature, and the
amount of salt in the water. If the filter pump is running due to the freeze protection feature,
then the chlorinator will not operate during this time.
8
+
>
Set Day and Time
Wednesday 10: P
+
>
Set Day and Time
Wednesday
37
+
>
Set Day and Time
Wednesday 10:37P
>
Adjust the current day of the week
Move to hours setting
>
Adjust the current hour (including AM/PM, if applicable)
Move to minutes setting
>
Adjust the current minute
Move to previous/next menu item
Use this function to set the current day of the week and time. These values are used for all
the automatic timeclock functions of the Aqua Logic and are also displayed as part of the
default menu.
The Aqua Logic is designed to keep the clock running during power outages lasting less
than 7 days. If power has been off for longer than 7 days, then the time may have to be reset.
+
>
Display Light
On for 60 sec.
>
Toggle between Always On and On for 60 sec.
Move to previous/next menu item
This function controls the backlight on the display. If the “60 seconds” option is selected,
then the backlight will automatically turn off 60 seconds after the last key is pressed and will
stay off until next time a key is pressed.
Note that the Display Light selection only applies to the display keypad that you are currently
using. Other display/keypads will not be affected. In other words, you need to individually
set this option for each display/keypad in the system.
+
>
Beeper
Enabled
>
Toggle between Beeper Enabled (default) and Disabled
Move to previous/next menu item
When “Enabled”, the keypad will beep every time a key is pressed. If this is not desired,
select “Disabled”.
This function only applies to the display/keypad that you are currently using. You need to
set this option for each display/keypad in your system.
NOTE: This function is not supported on all display/keypads. If the “Enabled” selection is
not blinking, then the current software revision of that particular keypad/display does not
support the option and it will default to Beeper Enabled.
+
Teach Wireless
+ to start
>
Press and hold
wireless button
Press any button on wireless remote
Move to previous/next menu item
>
Move to previous/next menu item
>
Teach Wireless
Base NOT Found
>
>
Teach Wireless
NOT Successful
Push to start process
Move to previous/next menu item
>
Teach Wireless
Successful
>
>
Move to previous/next menu item
The pool’s chemistry must be balanced BEFORE activating the Aqua Logic’s optional chlorinator function. NOTE: If the pool does not have new water, add metal remover and non-copper based algaecide
to the pool, per manufacturer’s instructions. This ensures a quick, troublefree transfer to the Aqua Logic
system.
Salt (When using optional chlorinator function - requires AQL-CL chlorination kit)
Salt Level
Use the chart on the following page to determine how much salt in pounds or (Kgs) should be added to
reach the recommended levels. Use the equations below (measurements are in feet/gallons and meters/
liters) if pool size is unknown.
Liters
Gallons
Length x Width x
Average Depth x 1000
Round
Diameter x Diameter x
Average Depth x 5.9
Diameter x Diameter x
Average Depth x 785
Oval
Length x Width x
Average Depth x 6.7
Length x Width x
Average Depth x 893
The operating salt level is between 2700-3400 PPM (parts per million) with 3200 PPM being optimal.
Before adding any salt, test the salt level. This is especially important for retrofit installation to older pools
where chlorine added to the pool over time has ended up as salt. If the level is low, determine the number
of gallons in the pool and add salt according to the chart below. A low salt level will reduce the efficiency
of the sanitization and result in low chlorine production. A high salt level can cause the Aqua Logic to stop
chlorinating. The salt in your pool/spa is constantly recycled and the loss of salt throughout the swimming
season should be minimal. This loss is due primarily to the addition of water because of splashing,
backwashing, or draining (because of rain). Salt is not lost due to evaporation.
Type of Salt to Use
It is important to use only sodium chloride (NaCl) salt that is greater than 99.0% pure. This can be found
at most pool stores in 40-80 lb. bags labeled “for use in swimming pools”. Alternatively, use common food
quality or water softener salt that is at least 99.0% pure. It is also acceptable to use water conditioning salt
pellets, however, it will take longer for them to dissolve. Do not use rock salt, or salt with more than 1%
of yellow prussiate of soda, salt with anti-caking additives, or iodized salt.
How to Add Salt
For new plaster pools, wait 10-14 days before adding salt to allow the plaster to cure. Turn the circulating
pump on and add salt directly into the pool. Brush the salt around to speed up the dissolving process—do
not allow salt to pile up on the bottom of the pool. Run the filter pump for 24 hours with the suction coming
from the main drain (use pool vacuum if there is no main drain) to allow the salt to evenly disperse throughout the pool. The salt display may take 24 hours to respond to the change in salt concentration.
Always check stabilizer (cyanuric acid), when checking salt. These levels will most likely decline together.
Use the chart on page 28 to determine how much stabilizer must be added to raise the level to 80 ppm.
This menu will only appear if a wireless base station is connected to the Aqua Logic. Perform
this procedure each time a wireless remote control is added to the Aqua Logic system.
9
(pool size in meters)
(pool size in feet)
Rectangular Length x Width x
Average Depth x 7.5
26
During this procedure the wireless remote “learns” and remembers the ID code for the
wireless base station connected to this particular Aqua Logic unit and will reject messages
with any other ID codes. If “Base NOT found” is displayed, then the Aqua Logic can not
communicate with the transmitter/receiver base station attached to the main unit. If “NOT
Successful” is displayed, then the base station did not receive a signal from the remote
control. This may be due to the distance between the Base Receiver and the remote device
being too great or may be due to interference caused by other RF equipment operating in the
neighborhood. Try changing the channel and then repeat the “Teach Wireless” command.
Salt is required only if you are using the chlorinator features on the Aqua Logic Control. If you are NOT
using the chlorinator, it is recommended that you follow all of the other chemistry recommendations besides salt. Refer to the description of the Aqua Logic configuration menu for information on enabling/
disabling the chlorinator (see page 14).
Wireless
Channel: 1
Water Chemistry
The table below summarizes the levels that are recommended by the Association of Pool and Spa Professionals (APSP). The only special requirements for the Aqua Logic are the salt level and stabilizer.
Confirm Change:
+ to proceed
Reteach all
wireless units
>
>
>
>
General Water Chemistry
>
>
Chlorinator Operation / Water Chemistry
>
Change the desired wireless channel (1 - 5)
If channel is changed, move to confirmation menu
If channel is not changed, move to previous/next menu item
Push to confirm the channel change
Move to previous/next menu item
>
Move to previous (Teach Wireless) menu
+
+
This setting changes the channel to be used by the wireless base station and remote(s). If
the channel is changed and confirmed, all of the wireless remotes will have to be retaught.
This menu will only appear if a wireless base station is connected to the Aqua Logic.
Timers Menu
The Timers Menu allows you to set all timeclock and countdown timers which control the automatic
operation of your pool/spa system.
Each timeclock has a single on/off program per day. All of the timeclocks are setup (Configuration Menu)
either as “all days” or “weekends/weekdays”. If “weekends/weekdays” are selected, you will need to
program on times for both weekdays and weekends and off times for both weekdays and weekends, even
if you want them to be the same. All times are adjusted in 15 minute increments (9:00A, 9:15A, 9:30A,
etc.). If you program the on time equal to the off time (“10:00A to 10:00A”) the output will NEVER turn
on. If you want to disable a timeclock, you can set the on time equal to the off time and you will notice the
times disappear and the display simply shows “Off”. If, at a later time, you wish to re-activate the timeclock,
simply press either the “+” or “-” buttons to go back to a normal timeclock programming display.
Saturation index
The saturation index (Si) relates to the calcium and alkalinity in the water and is an indicator of the pool
water “balance”. Your water is properly balanced if the Si is 0 ±0.2. If the Si is below -0.2, the water is
corrosive and plaster pool walls will be dissolved into the water. If the Si is above +0.2, scaling and
staining will occur. Use the chart below to determine the saturation index.
The Countdown timer is programmed in increments of 5 minutes from “Manual On/Off” (0 minutes) to a
maximum of “21:00” (21 hours). When “Manual On/Off” is displayed, the countdown timer is disabled
and the output will be manually controlled. When a countdown timer is equal or greater than “0:05”,
pressing the appropriate output button will turn the output on and start the timer. Pressing the button again
will turn the output off or, when the programmed time has elapsed, the output will automatically turn off.
Si = pH + Ti + Ci + Ai - 12.1
12
53
.3
Calcuim
Hardness
Ci
75
100
125
150
1.5
Total
Alkalinity
1.6
1.7
1.8
16
60
.4
19
66
.5
24
76
.6
200
250
29
84
.7
300
1.9
2.0
2.1
34
94
.8
39
103
.9
400
600
800
2.2
2.4
2.5
Ai
75
100
125
150
1.9
200
250
300
2.3
2.4
2.5
400
600
800
2.6
2.8
2.9
2.0
2.1
2.2
How to use: Measure pool pH, temperature, calcium hardness,
and total alkalinity. Use the chart above to determine Ti, Ci,and
Ai from your measurements. Insert values of pH, Ti, Ci and Ai
into the above equation. If Si equals .2 or more, scaling and
staining may occur. If Si equals -.2 or less corrosion or irritation
may occur.
-.2
0
CORROSIVE
.2
SCALING
or
SetFilter
Day and
T1-all
Time
Wednesday
8:30A to 4:00P
10:37P
Filter T1-wkend
8:30A to 4:00P
Filter T1-wkday
8:30A to 4:00P
+
+
+
>
Ti
>
ºF
>
ºC
>
Adjust time s
setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
For one speed pumps, this is the first filter timeclock and will determine the normal hours of
filtration for the pool. For pool/spa combination systems with spillover enabled, the valves
will automatically switch to spillover mode at the start of the filtration period. For all other
systems, the valves will switch to the pool-only position. Refer to the text above for general
notes regarding timeclock programming.
OK
25
10
For two speed pumps, this setting will be the period of time when the pump runs at high
speed (the word “Filter T1” in the display will be replaced with “Filter Hi”). There is a
separate timeclock for the low speed operation (see “Filter T2” below). If the high speed and
low speed periods overlap, then the pump will operate in low speed during the overlap
period.
There are several reasons the filter pump may be running at times other than the timeclock
period set above. These include super-chlorination, spa operation, manual operation, heater
cooldown, freeze protection and “solar-extend”.
+
>
Filter T2-wkday
8:30A to 4:00P
+
>
Filter T2-wkend
8:30A to 4:00P
+
>
or
SetFilter
Day and
T2-all
Time
Wednesday
8:30A to 4:00P
10:37P
>
Adjust time s
setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
Enter/Exit Service (or Service—Timed) Mode
1. Go to Aqua Logic main unit (normally mounted near the pool equipment)
2. Pressing the “Service” button rotates through normal operation (red LED off), service mode
(red LED on continuously) and service-timed mode (red LED flashing).
Note: This operation can only be performed at the main Aqua Logic unit. Both “Service” and “Service-Timed” disable all automatic programmed operations and allow
manual operation from the main unit only. The buttons on the remote display/keypads
will still be able to turn equipment off in case of an emergency, but will not turn any
equipment on. If the system is in “Serviced-Timed” it will automatically switch back to
normal operation at the end of the 3 hour time period.
For one speed pumps, this is the second filter timeclock
For two speed pumps, this timeclock will set the normal time period for filter pump low speed
operation (the word “Filter T2” in the display will be replaced with “Filter Lo”). If the filter
pump was off prior to the start of this time period, the filter pump will first turn on at high
speed for 3 minutes to prime and establish water flow. Afterwards, it will drop down to low
speed for the remainder of the programmed low speed time period. While this time clock will
override the high speed timeclock (see above), there are several reasons why the pump will
automatically switch to high speed operation during this programmed time period. These
include manual operation, spa operation, or heating operation. Refer to page 10 for general
notes regarding timeclock programming.
+
>
Spa-wkday
6:00P to 9:00P
+
>
Spa-wkend
6:00P to 9:00P
+
>
or
Set Day
Spa-all
and Time
Wednesday
6:00P to 9:00P
10:37P
>
Adjust time s
setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
This menu is only available if the system has been setup for “spa only” or “pool and spa”.
During the programmed spa time, the Aqua Logic will turn on the filter pump and move the
pool/spa valves into the “spa-only” position. The heater will automatically heat the spa up
to the programmed spa temperature (page 7). This programmed spa operation will take
precedence over all other automatic functions, only manual operation of the filter button or
pool/spa valve button will override this function.
If your pool has a separate jet pump or blower controlled by Aux1 and/or Aux2 , you will have
to program those separately (see page 12).
11
24
Lights-wkday
8:00P to 11:00P
+
>
Adjust time s
setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
This menu will appear only if the Lights are configured for timeclock. The lights will turn on
and off at the designated times. The only override on this function is manual on/off control
by the “Lights” button.
or
Start/Stop Superchlorination
+
>
Lights-wkend
8:00P to 11:00P
+
>
or
Set Lights-all
Day and Time
Wednesday
8:00P to 11:00P
10:37P
>
Note: Separate chlorinator output levels for the pool and spa must be set. If the valves
are in the pool-only or spa spillover positions, then the chlorinator will operate according the pool setting. If the valves are in the spa-only position then the chlorinator will
operate according to the spa setting. The actual amount of chlorine introduced into the
pool/spa is determined by: this output setting, the amount of time the filter pump is
running, the water temperature, and the amount of salt in the water. Also see Start/Stop
Superchlorination below.
1. Press the “MENU” button repeatedly until “Settings Menu” is displayed
2. Press the “>” button repeatedly until “Super Chlorinate” is displayed.
4. Press “+” or “-“ to toggle between “on” and “off”
Program a Timeclock
Aux1 and Aux2 configurations are identical.
Aux1-wkend
8:30A to 4:00P
Aux1-wkday
8:30A to 4:00P
+
+
>
3. Use the “+” and “-“ buttons to set the desired start time, then press “>” to switch to the off
time. Use the “+” and “-“ buttons to adjust the off time. If you are setting the “weekend”
timeclock, press “>” to go to the “weekday” settings.
+
>
or
Set Day
Aux1-all
and Time
Wednesday
8:30A to 4:00P
10:37P
>
1. Press the “MENU” button repeatedly until “Timers Menu” is displayed
Note: During the programmed time, there may be other automatic or manual operations that prevent the relay/valve from operating—see a more detailed discussion under
Automatic System Operation/Timers Menu/Aux Timeclock or in Troubleshooting/Diagnostic Information.
>
Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15...)
Move to previous/next menu item
This menu will appear only if the Lights are configured for countdown timer. This setting is
the time after you manually turn on the lights until the Aqua Logic automatically turns off the
lights. You can also manually turn off the lights at an earlier time by pressing the LIGHTS
button. If the Lights relay is on during the programmed off time, it may be because of freeze
protection.
Note: Once started, superchlorination will run for the programmed number of hours
(Timers Menu/Super Chlorinate Hours) or until you manually turn it off.
Superchlorination may be temporarily interrupted for a programmed spa operation.
2. Press the “>” button repeatedly until “xxx—all” or “xxx—wkend” (where xxx is the parameter
that you want to program) is displayed.
+
>
Lights-CountDn
0:20
3. The display will show whether superchlorination is “on” or “off”.
>
Adjust time s
setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
This menu will appear only if the Aux1 is configured for timeclock. The Aux output will turn
on and off at the designated times. If the Aux relay is off during the programmed on time—
note that some pool equipment (example pressure side pool cleaner) can only be operated
when the filter pump is running and the pool/spa valves are in the pool-only position—the
Aqua Logic will keep the relay off until these other conditions are suitable for operation. If
the Aux relay is on during the programmed off time, it may be because of freeze protection.
Also, manual operation overrides the timeclock.
or
Program a Countdown Timer
1. Press the “MENU” button repeatedly until “Timers Menu” is displayed
3. Use the “+” and “-“ buttons to set the desired timer period.
Note: A setting of 0:00 will display as “manual on/off”. The countdown automatic
turn off function is disabled but manual operation is still permitted. There may be other
automatic or manual operations that prevent the relay/valve from operating—see a
more detailed discussion under Automatic System Operation/Timers Menu/Aux Timeclock
or in Troubleshooting/Diagnostic Information.
23
Aux1-CountDn
0:20
+
>
2. Press the “>” button repeatedly until the “xxx—Timer” (where xxx is the parameter that you
want to program) is displayed.
>
Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15...)
Move to previous/next menu item
This menu will appear only if the Aux1 is configured for countdown timer. This setting is the
time after you manually turn on the Aux relay until the Aqua Logic automatically turns off the
relay. You can also manually turn off the relay at an earlier time by pressing the AUX1 button.
12
+
>
Valve3-wkday
8:30A to 4:00P
+
>
Valve3-wkend
8:30A to 4:00P
+
>
>
Adjust time s
setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
This menu will appear only if Valve3 is configured for timeclock. The valve will rotate on and
off at the designated times. There is no manual override. If the Valve3 relay is on during the
programmed off time, it may be because of freeze protection.
Super Chlorinate
24 hours
+
>
>
Adjust Superchlorination period (1 - 96 hours)
Move to previous/next menu item
Larger pools or when you have an unusually high bather load, a large amount of rain, a
cloudy water condition, or any other condition that requires a large amount of chlorine to be
introduced to the pool, may require more hours of Superchlorination. Smaller pools require
less hours of Superchlorination.
Quick “How To” Guide
Operate the Spa—Manually
1. Press the “Pool/Spa” button to go to “spa-only” operation (right LED illuminated). In some
cases, this may take more than one press of the button.
2. If the filter pump is not already on, press the “FILTER” button to turn it on.
3. If the spa is below the desired temperature, the heater will turn on automatically when the filter
pump is on and the valves are in the spa-only position. If you have not already set the desired
temperature for the spa, see “Set Heater Temperature” below
4. If the spa has a separate jet pump and or blower, determine if the jet pump/blower is controlled by Aux1 or Aux2 (it should be marked on the label inside the door). Then press the
appropriate button to turn on the jets/blower.
Operate the Spa—Automatically
1. Press the “MENU” button repeatedly until “Timers Menu” is displayed
2. Press the “>” button repeatedly until the “Spa—all” or “Spa—wkend” is displayed.
Configuration Menu
The Aqua Logic MUST BE CONFIGURED before attempting to operate. Configuration information is
entered at the keypad and “tells” the Aqua Logic what equipment is connected and how each should be
controlled.
3. Use the “+” and “-“ buttons to set the desired start time, then press “>” to switch to the off
time. Use the “+” and “-“ buttons to adjust the off time. If you are setting the “weekend”
timeclock, press “>” to go to the “weekday” settings.
CAUTION: When changing an existing configuration, it is important to understand how
the pool system operates and what specific equipment is connected to each output. Incorrect settings in the configuration menu could lead to damaged equipment and improper
operation of the pool system.
Note: During the programmed spa time, the valves will automatically switch to the
“spa-only” position, the filter pump will turn on, and, if the spa is not up to the desired
temperature, the heater will start. This operation is the highest priority and will take
precedence over other automatically programmed operations. At the end of the spa
period, the Aqua Logic will return to its normally programmed operation state.
!
Accessing the Configuration Menu
Configuring the Aqua Logic requires that you navigate through the Configuration Menu and input various
information. For more detailed information about using the Aqua Logic menu system, refer to the Operation Manual.
To access the Configuration Menu
Configuration
Menu-Unlocked
Menu
Press repeatedly until “Configuration Menu” is displayed
> Press BOTH buttons SIMULTANEOUSLY for 5 seconds to unlock
>
Configuration
Menu-Locked
>
or
Set Valve3-all
Day and Time
Wednesday
8:30A to 4:00P
10:37P
> Move to configuration menu items
NOTE: The configuration menu automatically “locks” after 2 minutes of no buttons being
pressed to prevent unauthorized people from changing the control logic inadvertently and
possibly damaging the pool equipment or causing a “call back” to fix the configuration.
13
Set the Heater Temperature (or turn heater permanently off)
1. Press the “MENU” button repeatedly until “Settings Menu” is displayed
2. Press the “>” button repeatedly until the “Spa Heater1” or “Pool Heater1” is displayed.
3. Press the “+” or “-“ buttons repeatedly to adjust the temperature. If you adjust the temperature below 65ºF or above 104°F the display will indicate “off” and the heater will not operate
regardless of temperature.
Note: Separate temperatures for the pool and spa must be set. If the valves are in the
pool-only or spa spillover positions, then the heater will use the pool setting. If the
valves are in the spa-only position then the heater will operate according to the spa
setting.
Set the Chlorinator Output
1. Press the “MENU” button repeatedly until “Settings Menu” is displayed
2. Press the “>” button repeatedly until the “Spa Chlorinator” or “Pool Chlorinator” is displayed.
3. Press the “+” or “-“ buttons repeatedly to adjust the setting. If you adjust the setting to 0% the
chlorinator will be off all the time
22
Configuration Menu Items
Each item needs to be programmed and may contain additional sub-menu items. Refer to the following
pages for information on programming.
>
Toggle between ºF and PPM (default) and ºC and g/L (Metric) options
Move to previous/next configuration menu
Chlor. Config.
+ to view/change
Chlorinator
Disabled
>
Display
Salt
>
Toggle between Display Salt (default) and Minerals
Move to previous/next configuration menu
Initiate reset of all configuration parameters
Move to previous/next configuration menu (config. not reset)
+
>
Reset all configuration parameters
Move to previous/next menu (config. not reset)
Chlorinator
If the chlorinator is enabled (requires the use of the AQL-CL chlorination kit), then the cell
and flow switch must also be installed and the Aqua Logic will automatically chlorinate both
the pool and spa according to the desired output setting (see Settings Menu in the Operation
manual). If disabled (default), then neither the cell nor flow switch need to be installed and
all displays relating to the chlorinator will be suppressed.
>
>
Move to previous/next configuration menu
When the chlorinator is enabled, the Aqua Logic will automatically detect and control any
Aqua Rite(s) that is installed in the system.
Use this function to erase all previous system configuration and reset all configuration
parameters back to the factory default values. This function is NOT reversible--be careful.
Display
Allows for the display of salt (default) or mineral values.
if “Pool and Spa” is selected
Spa - CountDn
00:30
if “Pool and Spa” is selected
Spa Spillover
Enabled
+
+
+
+
>
Pool/Spa Setup
Pool and Spa
Toggle between T-CELL-5 and T-CELL-15 (default)
Move
to next menu item
>
Cell Type Selection
The Cell Type Menu appears after “Display Salt/Minerals” in the Chlorinator Configuration
Menu. The options are T-CELL-5 or T-CELL-15 (default). Make the proper selection based
on the electrolytic cell that is used in your system. For pools up to 20,000 gallons, the TCELL-5 is typically used. The T-CELL-15 is for pools up to 40,000 gallons.
>
Pool/Spa Config.
+ to view/change
+
>
Cell Type
T-CELL-15
>
>
Push to access Pool/Spa options
Move to previous/next configuration menu item
>
Rotates between Pool and Spa, Spa Only, and Pool Only (default) options
Move to next menu item
>
Adjust time setting (Manual on/off, 0:05, 0:10, 0:15..., (default is 4:00))
Move to next menu item
>
Toggle between Enabled and Disabled (default) Spa Spillover
Move to next menu item or previous/next configuration menu
>
Toggle between Pool Only (default) and Spa Spillover options
Move to previous/next configuration menu
if “Pool and Spa” is selected
and if “Spa Spillover” is enabled
Filter Operation
Spa Spillover
+
>
if “Pool Only” or “Spa Only” is selected
V1=Aux1, V2=Aux2
Disabled
+
>
>
>
Config. reset
Confirmed
+
>
>
Are you sure?
+ to proceed
+
Push to access Chlorinator option
Move to next configuration menu
Toggle between Chlorinator Enabled and Disabled (default)
Move to next menu item
>
+
>
Reset Config. to
Default Press +
+
>
+
>
Toggle between 12 hour AM/PM (default) and 24 hour time format options
Move to previous/next configuration menu
>
>
Units
ºF and PPM
+
>
Time Format
12 hour AM/PM
>
Toggle between Enabled and Disabled (default)
Move to previous/next configuration menu
Pool/Spa Setup
If “Pool Only” or “Spa Only” are selected, then the pool/spa valves are not needed and
pushing the POOL/SPA button on the display/keypad will have no effect. If “Pool and Spa”
21
14
is selected, then the pool/spa suction and return valve actuators should be connected to the
Aqua Logic. Pressing the POOL/SPA button on the display/keypad will allow the homeowner
to alternate between pool and spa operation.
Super Chlorinate – if “Chlorinator” is enabled, this option allows the user to start a Super
Chlorinate cycle when the Valve3 button is pressed, rather than using the Settings Menu.
Note that only one button can me assigned to this function.
Spa CountDn
This menu will appear only if Pool/Spa Setup is set to “Pool and Spa”. This setting is the
time, after you manually switch the Pool/Spa valves to “Spa Only”, until the Aqua Logic
automatically returns the valves to their previous positions. It is programmed in increments
of 5 minutes, from “Manual On/Off” (0 minutes) to “21:00” (21 hours). The filter is forced on
during this time period.
Valve3 Interlock
If “Enabled”, this feature will override the function (timeclock or in-floor cleaner) selected
above and turn the valve off whenever the filter pump is off or the pool/spa suction/return
valves are set to “spa only” or “spillover” operation. Interlock is not available with solar.
Valve3 Freeze Protection
This function protects the pool and plumbed equipment against freeze damage. If Freeze
Protection is enabled and the AIR temperature falls below the selected freeze temperature
threshold, the Aqua Logic will turn on the valve to allow circulation of the water. IMPORTANT:
this only enables operation of the Valve3 output during freeze--see the “Filter Pump Config.”
menu to enable freeze protection for the main circulation system.
6B Spa Config.
+ to view/change
Select 6B Spa
A
6B A, Button 1
Pool/Spa
>
+
>
Toggle between 1-speed (default) and 2-speed options
Move to next menu item
>
Toggle between Enabled (default) and Disabled Freeze Protection
Move to next menu item or previous/next configuration menu
>
Adjust the desired freeze protection temperature (33ºF - 42ºF)
Move to previous/next configuration menu
Remote Menus
Enabled
>
Freeze Protection Temperature
Select the temperature to be used for freeze protection. Temperature is adjustable from 33ºF
- 42ºF (1ºC - 6ºC). 38ºF (3ºC) is default. This threshold will be used for all outputs that have
freeze protection enabled.
15
>
Rotates between all available remotes
Move to next menu item
Rotates between Pool/Spa, Filter, Lights, Heater1,
Aux1, and Aux2
Move to previous/next menu item or next configuration menu
+
>
Toggle between Enabled (default) and Disabled Remote Menus
Move to previous/next configuration menu
This feature will prevent unauthorized access to the Settings, Timers, and Configuration
menus from any of the Aqua Logic’s remote display/keypads. When disabled, the remote
display/keypads will only show the default menu and allow on/off control via the pushbuttons.
Note that the function of the Aqua Logic’s built-in display/keypad is unchanged by this
selection. Once disabled, the only way to enable “Remote Menus” is to use the local
display/keypad.
Filter Pump
Select single speed or 2-speed pump. If a 2-speed pump is configured, one of the AUX
relays must also be configured to control the low speed motor winding on the pump. See
page 3 for specific information regarding the control logic for 2-speed pump operation.
Freeze Protection
Freeze protection is used to protect the pool and plumbed equipment against freeze damage.
If freeze protection is enabled and the AIR temperature sensor falls below the freeze threshold
(see below), the Aqua Logic will turn on the filter pump to circulate the water. If “Pool and
Spa” is selected in the Pool/Spa sub-menu, the valves will also alternate between the pool
and spa every 30 minutes and the filter pump will turn off while the valves are turning. The
chlorinator will not operate if freeze protection is the only reason the pump is running.
>
Push to access the 6 Button Spa Side Remote options
Move to previous/next configuration menu
6B A, Button 1
This menu allows the user to map each button of the AQL-SS-6B to one of the standard Aqua
Logic functions. The default selections are: Button 1 - Pool/Spa, Button 2 - Filter, Button 3
- Lights, Button 4 - Heater1, Button 5 - Aux1 and Button 6 - Aux2.
All Timeclocks
7-day
+
>
+
>
Push to access pump options
Move to previous/next configuration menu
+
>
Freeze Temp
38ºF
+
>
Freeze Protect
Enabled
>
Filter Pump
1 Speed
+
+
>
Select 6B Spa
This menu only appears if more than one AQL-SS-6B is detected at power up. Select which
of the available remote controls (A, B or C) is to be configured.
V1=Aux1, V2=Aux2
This menu appears only if the Pool/Spa Setup is “Pool Only” or “Spa Only”. When enabled,
Valve 1 (return) will follow the Aux1 output and Valve 2 (suction) will follow the Aux2 output.
When disabled (default), the return and suction pool/spa valves function normally.
Filter Pump Config.
+ to view/change
+
>
If “Pool Only” is selected, then the Aqua Logic will switch the pool/spa valves to the “pool
only” position at the start of the programmed pool filtering time period or when the superchlorinate function is turned on. This may be desirable on some systems with in-floor
cleaners because it allows the cleaner to operate all the time the pool is being filtered and/or
the super chlorinate is running.
if AQL-SS-6B is connected
>
Filter Operation
If “Spa Spillover” is selected, the Aqua Logic will automatically switch the pool/spa suction
and return valves to “spillover” at the start of the programmed pool filtering time period or
when the super-chlorinate function is turned on. The valves will remain in this position for
the remainder of the super-chlorinate period. This option is usually preferable because both
the pool and spa water will be filtered and sanitized.
>
Spa Spillover
When spa spillover is “Enabled” and “Pool and Spa”, the homeowner will be able to rotate
through “Pool Only” (both suction and return valves switched to pool), “Spa Only” (both
suction and return valves switched to spa) and “Spillover” (suction valve switched to pool
and return valve switched to spa) by successive presses of the “Pool/Spa) button.
>
Toggle between 7-day (default) and Weekend/Weekday time options
Move to previous/next configuration menu
This selection affects ALL of the timeclock logic in the Aqua Logic. If “7-day” is selected,
each timeclock will have one set of turn-on/turn-off settings that operate every day of the
week. If “Weekend/Weekdays” option is selected then the user can enter one set of turn-on/
turn-off times for the weekend (fixed as Saturday/Sunday) and another set of turn-on/turnoff times for weekdays (Monday through Friday).
20
Heater1 Cooldown
Disabled
if “Heater1” is enabled
Heater1 Extend
Disabled
>
+
>
Valve3 Freeze
Disabled
+
>
Toggle between Enabled and Disabled (default) Valve3 Interlock
Move to next menu item
>
Toggle between Enabled and Disabled (default) Valve3 Freeze
Move to previous/next configuration menu
Solar
Disabled
if “Solar” is enabled
Solar Extend
Disabled
if “Solar” is enabled
Valve3 Function
Timeclock (default) – the valve turns on/off at the times set for the Valve3 timeclock in the
Timers Menu (see Operations Manual). The Valve 3 button can also be used to turn the
valve output on or off.
Solar – the valve operates when the filter pump is running and solar heat is available and the
water is less than the desired temperature setting. Solar heating must be enabled in the
“Solar Config. menu for proper operation to occur.
In-Floor Cleaner – the valve switches the water returning to the pool between the in-floor
cleaner and the normal return jets which facilitate efficient surface skimming. The valve will
operate the in-floor cleaner for the first half of each clock hour and then switch to the jets/
skimming for the last half of the hour.
19
>
Toggle between Enabled and Disabled (default) Heater 1 Extend
Move to previous/next configuration menu
Solar Priority
Disabled
+
+
+
+
>
>
Valve3 Interlock
Disabled
Solar Config.
+ to view/change
>
>
for all functions except solar
>
Toggle between Enabled and Disabled (default) Heater 1 Cooldown
Move to next menu item
Heater Extend
If “Enabled”, the filter extend logic keeps the filter pump running beyond the normal turn-off
time until the pool (or spa) is heated up to the desired temperature setting (see Settings
Menu). Heater extend will NOT cause the filter pump to turn on, it will only delay the turn
off time when the heater is operating.
>
+
>
Toggle between Enabled and Disabled (default) Heater 1
Move to next menu item or previous/next configuration menu
When the filter pump is running and the heater is on: Pressing the “Filter” button once will
cause the heater to turn off, but the filter pump will continue to run for heater cooldown (filter
LED flashing and message on display). Pushing the filter button a second time will override
the heater cooldown operation and turn the filter pump off.
>
>
Valve3 Function
Solar
Push to access Valve3 options
Move to previous/next configuration menu item
Rotates between Timeclock (default), Solar, In-Floor Cleaner,
and Super Chlorinate
Move to next menu item
>
Push to access heater options
Move to previous/next configuration menu
Heater Cooldown
This feature ensures that the heater cools down before water circulation is stopped. When
enabled, the Aqua Logic will continue to run the filter pump for 5 minutes after the heater
turns off. During this period the filter pump LED will flash and also a “Heater Cooldown,
X:XX remaining” message will scroll on the display.
Aux1 Freeze Protection
This function protects the pool, plumbing, and equipment against freeze damage. If Freeze
Protection is enabled and the AIR temperature sensor falls below the selected freeze
temperature threshold, the Aqua Logic will turn on the aux relay to circulate the water.
IMPORTANT: this only enables operation of the AUX output during freeze--see the “Filter
Pump Config.” menu to enable freeze protection for the main circulation system. Freeze
Protection is not available for low speed filter pump or dimmer.
+
+
>
Heater1
If the heater is “Enabled”, the heater relay will turn on when the water temperature is less
than the desired temperature setting and the filter pump is running. The desired temperature
is in the “Settings Menu”. If applicable, the homeowner will be prompted to enter separate
“pool” and “spa” settings. Depending on the position of the pool/spa suction valve, the
proper temperature setting will be used.
Aux1 Interlock
If “Enabled”, this feature will override the function (Manual On/Off, Countdown Timer,
Timeclock), selected above and turn the aux1 off when: filter pump is off, first 3 minutes of
filter pump operation (allows the pump to prime and get water flowing), when the pool/spa
suction return valves are in any position other than “pool only”, or for the first 3 minutes
after solar turns on (allows air in the solar panels to be purged). Interlock is not available for
solar, low speed filter pump, or dimmer.
Valve3 Config.
+ to view/change
+
>
Aux1 Relay
This feature allows the user to select either “Standard” (default) or “Dimmer” type relay for
the Aux1 output. The optional AQL-DIM dimmer kit must be installed if “Dimmer” is desired.
When “Dimmer” is selected, and the Aux1 output is manually turned on, the “+” and “-”
buttons adjust the level from 20% to 100% (default). The level is saved for the next time the
aux1 output is turned from off to on.
if “Heater1” is enabled
+
>
Super Chlorinate – if “Chlorinator” is enabled, this option allows the user to start a Super
Chlorinate cycle when the Aux button is pressed, rather than using the Settings Menu. Note
that only one button can me assigned to this function.
Heater1
Disabled
+
>
Low Speed of a 2-speed Filter Pump – the Aqua Logic will operate the aux relay whenever
the low speed operation of the filter pump is required. It is very important that the “2-speed”
filter pump option be selected under the “Filter Config.” Menu for proper operation.
Heater1 Config.
+ to view/change
>
Solar – the aux relay operates a solar booster pump which will turn on when the filter pump
is running and solar heat is available and the water is less than the desired temperature
setting. It is important to note that “Solar Control” must be enabled in the “Solar Config.”
menu for proper operation to occur.
>
Push to access solar options
Move to previous/next configuration menu
>
Toggle between Enabled and Disabled (default) Solar
Move to next menu item or previous/next configuration menu
>
Toggle between Enabled and Disabled (default) Solar Extend
Move to next menu item
>
Toggle between Enabled and Disabled (default) Solar Priority
Move to previous/next configuration menu
Solar
If the solar control logic is “Enabled”, several additional steps must be taken to ensure
proper operation of the solar system. If the solar is operated by a valve, then the Valve3
output must be setup for solar logic. If the solar is operated by a pump, then one of the AUX
relays must be set up for solar logic. Also, the “solar” temperature sensor must be installed.
This sensor is typically mounted near the collector array and is used to sense whether
sufficient solar heat is available.
If solar is “Enabled”, the valve or solar pump relay will turn on when the water temperature is
less than the desired temperature setting AND the solar sensor is hotter than the water. The
16
desired temperature is in the “Settings Menu”. If applicable, the homeowner will be prompted
to enter separate pool and spa desired temperature settings. Depending on the position of
the pool/spa suction valve, the proper temperature setting will be used.
Super Chlorinate – if “Chlorinator” is enabled, this option allows the user to start a Super
Chlorinate cycle when the Lights button is pressed, rather than using the Settings Menu.
Note that only one button can me assigned to this function.
Solar Extend
If “Enabled”, the filter extend logic keeps the filter pump running beyond the normal turn-off
time if solar heat is still available. When solar heat is no longer available, both the solar
valve/pump and filter pump will turn off simultaneously. Solar extend will NOT cause the
filter pump to turn on, it will only delay the turn off time when solar is operating.
Lights Relay
This feature allows the user to select either “Standard” (default) or “Dimmer” type relay for
the Lights output. The optional AQL-DIM dimmer kit must be installed if “Dimmer” is
desired. When “Dimmer” is selected, and the Lights output is manually turned on, the “+”
and “-” buttons adjust the level from 20% to 100% (default). The level is saved for the next
time the lights are turned from off to on.
Solar Priority
If both “Solar Control” and “Heater Control” are enabled, the Solar Priority feature will keep
the conventional heater off whenever solar heat is available. This provides the most cost
effective way of heating the pool. When solar heat is not available, the conventional heater
will operate normally.
+
>
Lights Interlock
Disabled
for all functions except
low speed of 2-speed filter pump
+
>
Lights Freeze
Disabled
>
Toggle between Enabled and Disabled (default) Lights Interlock
Move to next menu item
>
Toggle between Enabled and Disabled (default) Lights Freeze Protection
Move to previous/next configuration menu
NOTE: The configuration parameters for the Aux2 output is the same as shown below for Aux1.
Aux1 Config.
+ to view/change
Aux1 Function
Manual On/Off
for manual on/off, countdown
timer and timeclock functions
Lights Function
Although designated as the “Lights” output, the function of the lights relay is similar to the
aux1 and aux2 relays. If pool lights are wired to the lights relay, some options including Solar
function, Low Speed of a 2-Speed Filter Pump, Lights Interlock and Lights Freeze Protection
will not be necessary and should be disabled. If no pool lights are used, the lights relay can
be used to control other pool devices that may require these options. The function of each
option is shown below.
Manual On/Off—the lights relay will alternate between turning on and off when the LIGHTS
button is pressed. There is no automatic control logic.
Countdown Timer—the lights relay will turn on when the LIGHTS button is pressed. The
lights relay will turn off automatically after a programmed time (see Timers Menu in Operation
Manual). The LIGHTS button can also be used to turn the output off.
Aux1 Relay
Standard
+
>
Push to access Aux1 options
Move to previous/next configuration menu item
Rotates between Manual On/Off (default), Countdown Timer, Timeclock,
Solar, Low speed of a 2-speed pump options, and Super Chlorinate
Move to next menu item
>
Toggle between Standard (default) and Dimmer
Move to next menu item or previous/next configuration menu
>
Toggle between Enabled and Disabled (default) Aux1 Interlock
Move to next menu item
>
Toggle between Enabled (default) and Disabled Aux1 Freeze
Move to previous/next configuration menu
>
+
+
for all functions except solar and
low speed of 2-speed filter pump and dimmer
Aux1 Interlock
Disabled
+
for all functions except
low speed of 2-speed filter pump
Aux1 Freeze
Enabled
+
>
for all functions except solar and
low speed of 2-speed filter pump and dimmer
>
Toggle between Standard (default) and Dimmer
Move to next menu item or previous/next configuration menu
>
>
Lights Freeze Protection
This function helps protect equipment that is wired to the lights relay against freeze damage.
If Freeze Protection is enabled and the AIR temperature sensor falls below the selected freeze
temperature threshold, the Aqua Logic will energize the lights relay. IMPORTANT: this only
enables operation of the lights relay during freeze--see the “Filter Pump Config.” menu to
enable freeze protection for the main circulation system. Freeze Protection is not available
for low speed filter pump or dimmer.
>
+
>
Push to access Lights options
Move to previous/next configuration menu item
Rotates between Manual On/Off (default), Countdown Timer, Timeclock,
Solar, Low speed of a 2-speed pump options, and Super Chlorinate
Move to next menu item
>
>
Lights Relay
Standard
>
for manual on/off, countdown
timer and timeclock functions
+
>
Lights Function
Manual On/Off
+
>
Lights Config.
+ to view/change
Lights Interlock
If enabled, this feature will override the function (Manual On/Off, Countdown Timer,
Timeclock) selected above and turn the lights relay off when: filter pump is off, first 3
minutes of filter pump operation (allows the pump to prime and get water flowing), when the
pool/spa suction return valves are in any position other than “pool only”, or for the first 3
minutes after solar turns on (allows air in the solar panels to be purged). Interlock is not
available for solar, low speed filter pump, or dimmer.
! WARNING: Do not use the Aqua Logic to control an automatic pool cover. Swimmers may become entrapped underneath the cover.
Timeclock – the lights relay will turn-on and turn-off at the times set for the lights timeclock
in the Settings Menu (see Settings Menu in Operation Manual). The LIGHTS button can
also be used to turn the output on and off.
Aux1 Function
Manual On/Off (default)—the aux relay will alternate between turning on and off when the
aux button is pressed. There is no automatic control logic.
Solar – the lights relay can operate a solar booster pump which will turn on when the filter
pump is running and solar heat is available and the water is less than the desired temperature
setting. It is important to note that “Solar Control” must be enabled in the “Solar Config.”
menu for proper operation to occur.
Countdown Timer – the aux relay will turn on when the AUX button is pressed and then will
turn off automatically after a programmed time (see Timers Menu, Operation Manual). The
AUX button can also be used to turn the output off.
Low Speed of a 2-speed Filter Pump – the Aqua Logic will turn on the lights relay whenever
the low speed operation of the filter pump is required. It is very important that the “2-speed”
filter pump option be selected under the “Filter Config.” Menu for proper operation.
17
Timeclock – the aux relay will turn-on and turn-off at the times set for the aux1 timeclock in
the Timers Menu. The AUX button can also be used to turn the output on and off.
18
desired temperature is in the “Settings Menu”. If applicable, the homeowner will be prompted
to enter separate pool and spa desired temperature settings. Depending on the position of
the pool/spa suction valve, the proper temperature setting will be used.
Super Chlorinate – if “Chlorinator” is enabled, this option allows the user to start a Super
Chlorinate cycle when the Lights button is pressed, rather than using the Settings Menu.
Note that only one button can me assigned to this function.
Solar Extend
If “Enabled”, the filter extend logic keeps the filter pump running beyond the normal turn-off
time if solar heat is still available. When solar heat is no longer available, both the solar
valve/pump and filter pump will turn off simultaneously. Solar extend will NOT cause the
filter pump to turn on, it will only delay the turn off time when solar is operating.
Lights Relay
This feature allows the user to select either “Standard” (default) or “Dimmer” type relay for
the Lights output. The optional AQL-DIM dimmer kit must be installed if “Dimmer” is
desired. When “Dimmer” is selected, and the Lights output is manually turned on, the “+”
and “-” buttons adjust the level from 20% to 100% (default). The level is saved for the next
time the lights are turned from off to on.
Solar Priority
If both “Solar Control” and “Heater Control” are enabled, the Solar Priority feature will keep
the conventional heater off whenever solar heat is available. This provides the most cost
effective way of heating the pool. When solar heat is not available, the conventional heater
will operate normally.
+
>
Lights Interlock
Disabled
for all functions except
low speed of 2-speed filter pump
+
>
Lights Freeze
Disabled
>
Toggle between Enabled and Disabled (default) Lights Interlock
Move to next menu item
>
Toggle between Enabled and Disabled (default) Lights Freeze Protection
Move to previous/next configuration menu
NOTE: The configuration parameters for the Aux2 output is the same as shown below for Aux1.
Aux1 Config.
+ to view/change
Aux1 Function
Manual On/Off
for manual on/off, countdown
timer and timeclock functions
Lights Function
Although designated as the “Lights” output, the function of the lights relay is similar to the
aux1 and aux2 relays. If pool lights are wired to the lights relay, some options including Solar
function, Low Speed of a 2-Speed Filter Pump, Lights Interlock and Lights Freeze Protection
will not be necessary and should be disabled. If no pool lights are used, the lights relay can
be used to control other pool devices that may require these options. The function of each
option is shown below.
Manual On/Off—the lights relay will alternate between turning on and off when the LIGHTS
button is pressed. There is no automatic control logic.
Countdown Timer—the lights relay will turn on when the LIGHTS button is pressed. The
lights relay will turn off automatically after a programmed time (see Timers Menu in Operation
Manual). The LIGHTS button can also be used to turn the output off.
Aux1 Relay
Standard
+
>
Push to access Aux1 options
Move to previous/next configuration menu item
Rotates between Manual On/Off (default), Countdown Timer, Timeclock,
Solar, Low speed of a 2-speed pump options, and Super Chlorinate
Move to next menu item
>
Toggle between Standard (default) and Dimmer
Move to next menu item or previous/next configuration menu
>
Toggle between Enabled and Disabled (default) Aux1 Interlock
Move to next menu item
>
Toggle between Enabled (default) and Disabled Aux1 Freeze
Move to previous/next configuration menu
>
+
+
for all functions except solar and
low speed of 2-speed filter pump and dimmer
Aux1 Interlock
Disabled
+
for all functions except
low speed of 2-speed filter pump
Aux1 Freeze
Enabled
+
>
for all functions except solar and
low speed of 2-speed filter pump and dimmer
>
Toggle between Standard (default) and Dimmer
Move to next menu item or previous/next configuration menu
>
>
Lights Freeze Protection
This function helps protect equipment that is wired to the lights relay against freeze damage.
If Freeze Protection is enabled and the AIR temperature sensor falls below the selected freeze
temperature threshold, the Aqua Logic will energize the lights relay. IMPORTANT: this only
enables operation of the lights relay during freeze--see the “Filter Pump Config.” menu to
enable freeze protection for the main circulation system. Freeze Protection is not available
for low speed filter pump or dimmer.
>
+
>
Push to access Lights options
Move to previous/next configuration menu item
Rotates between Manual On/Off (default), Countdown Timer, Timeclock,
Solar, Low speed of a 2-speed pump options, and Super Chlorinate
Move to next menu item
>
>
Lights Relay
Standard
>
for manual on/off, countdown
timer and timeclock functions
+
>
Lights Function
Manual On/Off
+
>
Lights Config.
+ to view/change
Lights Interlock
If enabled, this feature will override the function (Manual On/Off, Countdown Timer,
Timeclock) selected above and turn the lights relay off when: filter pump is off, first 3
minutes of filter pump operation (allows the pump to prime and get water flowing), when the
pool/spa suction return valves are in any position other than “pool only”, or for the first 3
minutes after solar turns on (allows air in the solar panels to be purged). Interlock is not
available for solar, low speed filter pump, or dimmer.
! WARNING: Do not use the Aqua Logic to control an automatic pool cover. Swimmers may become entrapped underneath the cover.
Timeclock – the lights relay will turn-on and turn-off at the times set for the lights timeclock
in the Settings Menu (see Settings Menu in Operation Manual). The LIGHTS button can
also be used to turn the output on and off.
Aux1 Function
Manual On/Off (default)—the aux relay will alternate between turning on and off when the
aux button is pressed. There is no automatic control logic.
Solar – the lights relay can operate a solar booster pump which will turn on when the filter
pump is running and solar heat is available and the water is less than the desired temperature
setting. It is important to note that “Solar Control” must be enabled in the “Solar Config.”
menu for proper operation to occur.
Countdown Timer – the aux relay will turn on when the AUX button is pressed and then will
turn off automatically after a programmed time (see Timers Menu, Operation Manual). The
AUX button can also be used to turn the output off.
Low Speed of a 2-speed Filter Pump – the Aqua Logic will turn on the lights relay whenever
the low speed operation of the filter pump is required. It is very important that the “2-speed”
filter pump option be selected under the “Filter Config.” Menu for proper operation.
17
Timeclock – the aux relay will turn-on and turn-off at the times set for the aux1 timeclock in
the Timers Menu. The AUX button can also be used to turn the output on and off.
18
Heater1 Cooldown
Disabled
if “Heater1” is enabled
Heater1 Extend
Disabled
>
+
>
Valve3 Freeze
Disabled
+
>
Toggle between Enabled and Disabled (default) Valve3 Interlock
Move to next menu item
>
Toggle between Enabled and Disabled (default) Valve3 Freeze
Move to previous/next configuration menu
Solar
Disabled
if “Solar” is enabled
Solar Extend
Disabled
if “Solar” is enabled
Valve3 Function
Timeclock (default) – the valve turns on/off at the times set for the Valve3 timeclock in the
Timers Menu (see Operations Manual). The Valve 3 button can also be used to turn the
valve output on or off.
Solar – the valve operates when the filter pump is running and solar heat is available and the
water is less than the desired temperature setting. Solar heating must be enabled in the
“Solar Config. menu for proper operation to occur.
In-Floor Cleaner – the valve switches the water returning to the pool between the in-floor
cleaner and the normal return jets which facilitate efficient surface skimming. The valve will
operate the in-floor cleaner for the first half of each clock hour and then switch to the jets/
skimming for the last half of the hour.
19
>
Toggle between Enabled and Disabled (default) Heater 1 Extend
Move to previous/next configuration menu
Solar Priority
Disabled
+
+
+
+
>
>
Valve3 Interlock
Disabled
Solar Config.
+ to view/change
>
>
for all functions except solar
>
Toggle between Enabled and Disabled (default) Heater 1 Cooldown
Move to next menu item
Heater Extend
If “Enabled”, the filter extend logic keeps the filter pump running beyond the normal turn-off
time until the pool (or spa) is heated up to the desired temperature setting (see Settings
Menu). Heater extend will NOT cause the filter pump to turn on, it will only delay the turn
off time when the heater is operating.
>
+
>
Toggle between Enabled and Disabled (default) Heater 1
Move to next menu item or previous/next configuration menu
When the filter pump is running and the heater is on: Pressing the “Filter” button once will
cause the heater to turn off, but the filter pump will continue to run for heater cooldown (filter
LED flashing and message on display). Pushing the filter button a second time will override
the heater cooldown operation and turn the filter pump off.
>
>
Valve3 Function
Solar
Push to access Valve3 options
Move to previous/next configuration menu item
Rotates between Timeclock (default), Solar, In-Floor Cleaner,
and Super Chlorinate
Move to next menu item
>
Push to access heater options
Move to previous/next configuration menu
Heater Cooldown
This feature ensures that the heater cools down before water circulation is stopped. When
enabled, the Aqua Logic will continue to run the filter pump for 5 minutes after the heater
turns off. During this period the filter pump LED will flash and also a “Heater Cooldown,
X:XX remaining” message will scroll on the display.
Aux1 Freeze Protection
This function protects the pool, plumbing, and equipment against freeze damage. If Freeze
Protection is enabled and the AIR temperature sensor falls below the selected freeze
temperature threshold, the Aqua Logic will turn on the aux relay to circulate the water.
IMPORTANT: this only enables operation of the AUX output during freeze--see the “Filter
Pump Config.” menu to enable freeze protection for the main circulation system. Freeze
Protection is not available for low speed filter pump or dimmer.
+
+
>
Heater1
If the heater is “Enabled”, the heater relay will turn on when the water temperature is less
than the desired temperature setting and the filter pump is running. The desired temperature
is in the “Settings Menu”. If applicable, the homeowner will be prompted to enter separate
“pool” and “spa” settings. Depending on the position of the pool/spa suction valve, the
proper temperature setting will be used.
Aux1 Interlock
If “Enabled”, this feature will override the function (Manual On/Off, Countdown Timer,
Timeclock), selected above and turn the aux1 off when: filter pump is off, first 3 minutes of
filter pump operation (allows the pump to prime and get water flowing), when the pool/spa
suction return valves are in any position other than “pool only”, or for the first 3 minutes
after solar turns on (allows air in the solar panels to be purged). Interlock is not available for
solar, low speed filter pump, or dimmer.
Valve3 Config.
+ to view/change
+
>
Aux1 Relay
This feature allows the user to select either “Standard” (default) or “Dimmer” type relay for
the Aux1 output. The optional AQL-DIM dimmer kit must be installed if “Dimmer” is desired.
When “Dimmer” is selected, and the Aux1 output is manually turned on, the “+” and “-”
buttons adjust the level from 20% to 100% (default). The level is saved for the next time the
aux1 output is turned from off to on.
if “Heater1” is enabled
+
>
Super Chlorinate – if “Chlorinator” is enabled, this option allows the user to start a Super
Chlorinate cycle when the Aux button is pressed, rather than using the Settings Menu. Note
that only one button can me assigned to this function.
Heater1
Disabled
+
>
Low Speed of a 2-speed Filter Pump – the Aqua Logic will operate the aux relay whenever
the low speed operation of the filter pump is required. It is very important that the “2-speed”
filter pump option be selected under the “Filter Config.” Menu for proper operation.
Heater1 Config.
+ to view/change
>
Solar – the aux relay operates a solar booster pump which will turn on when the filter pump
is running and solar heat is available and the water is less than the desired temperature
setting. It is important to note that “Solar Control” must be enabled in the “Solar Config.”
menu for proper operation to occur.
>
Push to access solar options
Move to previous/next configuration menu
>
Toggle between Enabled and Disabled (default) Solar
Move to next menu item or previous/next configuration menu
>
Toggle between Enabled and Disabled (default) Solar Extend
Move to next menu item
>
Toggle between Enabled and Disabled (default) Solar Priority
Move to previous/next configuration menu
Solar
If the solar control logic is “Enabled”, several additional steps must be taken to ensure
proper operation of the solar system. If the solar is operated by a valve, then the Valve3
output must be setup for solar logic. If the solar is operated by a pump, then one of the AUX
relays must be set up for solar logic. Also, the “solar” temperature sensor must be installed.
This sensor is typically mounted near the collector array and is used to sense whether
sufficient solar heat is available.
If solar is “Enabled”, the valve or solar pump relay will turn on when the water temperature is
less than the desired temperature setting AND the solar sensor is hotter than the water. The
16
is selected, then the pool/spa suction and return valve actuators should be connected to the
Aqua Logic. Pressing the POOL/SPA button on the display/keypad will allow the homeowner
to alternate between pool and spa operation.
Super Chlorinate – if “Chlorinator” is enabled, this option allows the user to start a Super
Chlorinate cycle when the Valve3 button is pressed, rather than using the Settings Menu.
Note that only one button can me assigned to this function.
Spa CountDn
This menu will appear only if Pool/Spa Setup is set to “Pool and Spa”. This setting is the
time, after you manually switch the Pool/Spa valves to “Spa Only”, until the Aqua Logic
automatically returns the valves to their previous positions. It is programmed in increments
of 5 minutes, from “Manual On/Off” (0 minutes) to “21:00” (21 hours). The filter is forced on
during this time period.
Valve3 Interlock
If “Enabled”, this feature will override the function (timeclock or in-floor cleaner) selected
above and turn the valve off whenever the filter pump is off or the pool/spa suction/return
valves are set to “spa only” or “spillover” operation. Interlock is not available with solar.
Valve3 Freeze Protection
This function protects the pool and plumbed equipment against freeze damage. If Freeze
Protection is enabled and the AIR temperature falls below the selected freeze temperature
threshold, the Aqua Logic will turn on the valve to allow circulation of the water. IMPORTANT:
this only enables operation of the Valve3 output during freeze--see the “Filter Pump Config.”
menu to enable freeze protection for the main circulation system.
6B Spa Config.
+ to view/change
Select 6B Spa
A
6B A, Button 1
Pool/Spa
>
+
>
Toggle between 1-speed (default) and 2-speed options
Move to next menu item
>
Toggle between Enabled (default) and Disabled Freeze Protection
Move to next menu item or previous/next configuration menu
>
Adjust the desired freeze protection temperature (33ºF - 42ºF)
Move to previous/next configuration menu
Remote Menus
Enabled
>
Freeze Protection Temperature
Select the temperature to be used for freeze protection. Temperature is adjustable from 33ºF
- 42ºF (1ºC - 6ºC). 38ºF (3ºC) is default. This threshold will be used for all outputs that have
freeze protection enabled.
15
>
Rotates between all available remotes
Move to next menu item
Rotates between Pool/Spa, Filter, Lights, Heater1,
Aux1, and Aux2
Move to previous/next menu item or next configuration menu
+
>
Toggle between Enabled (default) and Disabled Remote Menus
Move to previous/next configuration menu
This feature will prevent unauthorized access to the Settings, Timers, and Configuration
menus from any of the Aqua Logic’s remote display/keypads. When disabled, the remote
display/keypads will only show the default menu and allow on/off control via the pushbuttons.
Note that the function of the Aqua Logic’s built-in display/keypad is unchanged by this
selection. Once disabled, the only way to enable “Remote Menus” is to use the local
display/keypad.
Filter Pump
Select single speed or 2-speed pump. If a 2-speed pump is configured, one of the AUX
relays must also be configured to control the low speed motor winding on the pump. See
page 3 for specific information regarding the control logic for 2-speed pump operation.
Freeze Protection
Freeze protection is used to protect the pool and plumbed equipment against freeze damage.
If freeze protection is enabled and the AIR temperature sensor falls below the freeze threshold
(see below), the Aqua Logic will turn on the filter pump to circulate the water. If “Pool and
Spa” is selected in the Pool/Spa sub-menu, the valves will also alternate between the pool
and spa every 30 minutes and the filter pump will turn off while the valves are turning. The
chlorinator will not operate if freeze protection is the only reason the pump is running.
>
Push to access the 6 Button Spa Side Remote options
Move to previous/next configuration menu
6B A, Button 1
This menu allows the user to map each button of the AQL-SS-6B to one of the standard Aqua
Logic functions. The default selections are: Button 1 - Pool/Spa, Button 2 - Filter, Button 3
- Lights, Button 4 - Heater1, Button 5 - Aux1 and Button 6 - Aux2.
All Timeclocks
7-day
+
>
+
>
Push to access pump options
Move to previous/next configuration menu
+
>
Freeze Temp
38ºF
+
>
Freeze Protect
Enabled
>
Filter Pump
1 Speed
+
+
>
Select 6B Spa
This menu only appears if more than one AQL-SS-6B is detected at power up. Select which
of the available remote controls (A, B or C) is to be configured.
V1=Aux1, V2=Aux2
This menu appears only if the Pool/Spa Setup is “Pool Only” or “Spa Only”. When enabled,
Valve 1 (return) will follow the Aux1 output and Valve 2 (suction) will follow the Aux2 output.
When disabled (default), the return and suction pool/spa valves function normally.
Filter Pump Config.
+ to view/change
+
>
If “Pool Only” is selected, then the Aqua Logic will switch the pool/spa valves to the “pool
only” position at the start of the programmed pool filtering time period or when the superchlorinate function is turned on. This may be desirable on some systems with in-floor
cleaners because it allows the cleaner to operate all the time the pool is being filtered and/or
the super chlorinate is running.
if AQL-SS-6B is connected
>
Filter Operation
If “Spa Spillover” is selected, the Aqua Logic will automatically switch the pool/spa suction
and return valves to “spillover” at the start of the programmed pool filtering time period or
when the super-chlorinate function is turned on. The valves will remain in this position for
the remainder of the super-chlorinate period. This option is usually preferable because both
the pool and spa water will be filtered and sanitized.
>
Spa Spillover
When spa spillover is “Enabled” and “Pool and Spa”, the homeowner will be able to rotate
through “Pool Only” (both suction and return valves switched to pool), “Spa Only” (both
suction and return valves switched to spa) and “Spillover” (suction valve switched to pool
and return valve switched to spa) by successive presses of the “Pool/Spa) button.
>
Toggle between 7-day (default) and Weekend/Weekday time options
Move to previous/next configuration menu
This selection affects ALL of the timeclock logic in the Aqua Logic. If “7-day” is selected,
each timeclock will have one set of turn-on/turn-off settings that operate every day of the
week. If “Weekend/Weekdays” option is selected then the user can enter one set of turn-on/
turn-off times for the weekend (fixed as Saturday/Sunday) and another set of turn-on/turnoff times for weekdays (Monday through Friday).
20
Configuration Menu Items
Each item needs to be programmed and may contain additional sub-menu items. Refer to the following
pages for information on programming.
>
Toggle between ºF and PPM (default) and ºC and g/L (Metric) options
Move to previous/next configuration menu
Chlor. Config.
+ to view/change
Chlorinator
Disabled
>
Display
Salt
>
Toggle between Display Salt (default) and Minerals
Move to previous/next configuration menu
Initiate reset of all configuration parameters
Move to previous/next configuration menu (config. not reset)
+
>
Reset all configuration parameters
Move to previous/next menu (config. not reset)
Chlorinator
If the chlorinator is enabled (requires the use of the AQL-CL chlorination kit), then the cell
and flow switch must also be installed and the Aqua Logic will automatically chlorinate both
the pool and spa according to the desired output setting (see Settings Menu in the Operation
manual). If disabled (default), then neither the cell nor flow switch need to be installed and
all displays relating to the chlorinator will be suppressed.
>
>
Move to previous/next configuration menu
When the chlorinator is enabled, the Aqua Logic will automatically detect and control any
Aqua Rite(s) that is installed in the system.
Use this function to erase all previous system configuration and reset all configuration
parameters back to the factory default values. This function is NOT reversible--be careful.
Display
Allows for the display of salt (default) or mineral values.
if “Pool and Spa” is selected
Spa - CountDn
00:30
if “Pool and Spa” is selected
Spa Spillover
Enabled
+
+
+
+
>
Pool/Spa Setup
Pool and Spa
Toggle between T-CELL-5 and T-CELL-15 (default)
Move
to next menu item
>
Cell Type Selection
The Cell Type Menu appears after “Display Salt/Minerals” in the Chlorinator Configuration
Menu. The options are T-CELL-5 or T-CELL-15 (default). Make the proper selection based
on the electrolytic cell that is used in your system. For pools up to 20,000 gallons, the TCELL-5 is typically used. The T-CELL-15 is for pools up to 40,000 gallons.
>
Pool/Spa Config.
+ to view/change
+
>
Cell Type
T-CELL-15
>
>
Push to access Pool/Spa options
Move to previous/next configuration menu item
>
Rotates between Pool and Spa, Spa Only, and Pool Only (default) options
Move to next menu item
>
Adjust time setting (Manual on/off, 0:05, 0:10, 0:15..., (default is 4:00))
Move to next menu item
>
Toggle between Enabled and Disabled (default) Spa Spillover
Move to next menu item or previous/next configuration menu
>
Toggle between Pool Only (default) and Spa Spillover options
Move to previous/next configuration menu
if “Pool and Spa” is selected
and if “Spa Spillover” is enabled
Filter Operation
Spa Spillover
+
>
if “Pool Only” or “Spa Only” is selected
V1=Aux1, V2=Aux2
Disabled
+
>
>
>
Config. reset
Confirmed
+
>
>
Are you sure?
+ to proceed
+
Push to access Chlorinator option
Move to next configuration menu
Toggle between Chlorinator Enabled and Disabled (default)
Move to next menu item
>
+
>
Reset Config. to
Default Press +
+
>
+
>
Toggle between 12 hour AM/PM (default) and 24 hour time format options
Move to previous/next configuration menu
>
>
Units
ºF and PPM
+
>
Time Format
12 hour AM/PM
>
Toggle between Enabled and Disabled (default)
Move to previous/next configuration menu
Pool/Spa Setup
If “Pool Only” or “Spa Only” are selected, then the pool/spa valves are not needed and
pushing the POOL/SPA button on the display/keypad will have no effect. If “Pool and Spa”
21
14
+
>
Valve3-wkday
8:30A to 4:00P
+
>
Valve3-wkend
8:30A to 4:00P
+
>
>
Adjust time s
setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
This menu will appear only if Valve3 is configured for timeclock. The valve will rotate on and
off at the designated times. There is no manual override. If the Valve3 relay is on during the
programmed off time, it may be because of freeze protection.
Super Chlorinate
24 hours
+
>
>
Adjust Superchlorination period (1 - 96 hours)
Move to previous/next menu item
Larger pools or when you have an unusually high bather load, a large amount of rain, a
cloudy water condition, or any other condition that requires a large amount of chlorine to be
introduced to the pool, may require more hours of Superchlorination. Smaller pools require
less hours of Superchlorination.
Quick “How To” Guide
Operate the Spa—Manually
1. Press the “Pool/Spa” button to go to “spa-only” operation (right LED illuminated). In some
cases, this may take more than one press of the button.
2. If the filter pump is not already on, press the “FILTER” button to turn it on.
3. If the spa is below the desired temperature, the heater will turn on automatically when the filter
pump is on and the valves are in the spa-only position. If you have not already set the desired
temperature for the spa, see “Set Heater Temperature” below
4. If the spa has a separate jet pump and or blower, determine if the jet pump/blower is controlled by Aux1 or Aux2 (it should be marked on the label inside the door). Then press the
appropriate button to turn on the jets/blower.
Operate the Spa—Automatically
1. Press the “MENU” button repeatedly until “Timers Menu” is displayed
2. Press the “>” button repeatedly until the “Spa—all” or “Spa—wkend” is displayed.
Configuration Menu
The Aqua Logic MUST BE CONFIGURED before attempting to operate. Configuration information is
entered at the keypad and “tells” the Aqua Logic what equipment is connected and how each should be
controlled.
3. Use the “+” and “-“ buttons to set the desired start time, then press “>” to switch to the off
time. Use the “+” and “-“ buttons to adjust the off time. If you are setting the “weekend”
timeclock, press “>” to go to the “weekday” settings.
CAUTION: When changing an existing configuration, it is important to understand how
the pool system operates and what specific equipment is connected to each output. Incorrect settings in the configuration menu could lead to damaged equipment and improper
operation of the pool system.
Note: During the programmed spa time, the valves will automatically switch to the
“spa-only” position, the filter pump will turn on, and, if the spa is not up to the desired
temperature, the heater will start. This operation is the highest priority and will take
precedence over other automatically programmed operations. At the end of the spa
period, the Aqua Logic will return to its normally programmed operation state.
!
Accessing the Configuration Menu
Configuring the Aqua Logic requires that you navigate through the Configuration Menu and input various
information. For more detailed information about using the Aqua Logic menu system, refer to the Operation Manual.
To access the Configuration Menu
Configuration
Menu-Unlocked
Menu
Press repeatedly until “Configuration Menu” is displayed
> Press BOTH buttons SIMULTANEOUSLY for 5 seconds to unlock
>
Configuration
Menu-Locked
>
or
Set Valve3-all
Day and Time
Wednesday
8:30A to 4:00P
10:37P
> Move to configuration menu items
NOTE: The configuration menu automatically “locks” after 2 minutes of no buttons being
pressed to prevent unauthorized people from changing the control logic inadvertently and
possibly damaging the pool equipment or causing a “call back” to fix the configuration.
13
Set the Heater Temperature (or turn heater permanently off)
1. Press the “MENU” button repeatedly until “Settings Menu” is displayed
2. Press the “>” button repeatedly until the “Spa Heater1” or “Pool Heater1” is displayed.
3. Press the “+” or “-“ buttons repeatedly to adjust the temperature. If you adjust the temperature below 65ºF or above 104°F the display will indicate “off” and the heater will not operate
regardless of temperature.
Note: Separate temperatures for the pool and spa must be set. If the valves are in the
pool-only or spa spillover positions, then the heater will use the pool setting. If the
valves are in the spa-only position then the heater will operate according to the spa
setting.
Set the Chlorinator Output
1. Press the “MENU” button repeatedly until “Settings Menu” is displayed
2. Press the “>” button repeatedly until the “Spa Chlorinator” or “Pool Chlorinator” is displayed.
3. Press the “+” or “-“ buttons repeatedly to adjust the setting. If you adjust the setting to 0% the
chlorinator will be off all the time
22
Lights-wkday
8:00P to 11:00P
+
>
Adjust time s
setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
This menu will appear only if the Lights are configured for timeclock. The lights will turn on
and off at the designated times. The only override on this function is manual on/off control
by the “Lights” button.
or
Start/Stop Superchlorination
+
>
Lights-wkend
8:00P to 11:00P
+
>
or
Set Lights-all
Day and Time
Wednesday
8:00P to 11:00P
10:37P
>
Note: Separate chlorinator output levels for the pool and spa must be set. If the valves
are in the pool-only or spa spillover positions, then the chlorinator will operate according the pool setting. If the valves are in the spa-only position then the chlorinator will
operate according to the spa setting. The actual amount of chlorine introduced into the
pool/spa is determined by: this output setting, the amount of time the filter pump is
running, the water temperature, and the amount of salt in the water. Also see Start/Stop
Superchlorination below.
1. Press the “MENU” button repeatedly until “Settings Menu” is displayed
2. Press the “>” button repeatedly until “Super Chlorinate” is displayed.
4. Press “+” or “-“ to toggle between “on” and “off”
Program a Timeclock
Aux1 and Aux2 configurations are identical.
Aux1-wkend
8:30A to 4:00P
Aux1-wkday
8:30A to 4:00P
+
+
>
3. Use the “+” and “-“ buttons to set the desired start time, then press “>” to switch to the off
time. Use the “+” and “-“ buttons to adjust the off time. If you are setting the “weekend”
timeclock, press “>” to go to the “weekday” settings.
+
>
or
Set Day
Aux1-all
and Time
Wednesday
8:30A to 4:00P
10:37P
>
1. Press the “MENU” button repeatedly until “Timers Menu” is displayed
Note: During the programmed time, there may be other automatic or manual operations that prevent the relay/valve from operating—see a more detailed discussion under
Automatic System Operation/Timers Menu/Aux Timeclock or in Troubleshooting/Diagnostic Information.
>
Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15...)
Move to previous/next menu item
This menu will appear only if the Lights are configured for countdown timer. This setting is
the time after you manually turn on the lights until the Aqua Logic automatically turns off the
lights. You can also manually turn off the lights at an earlier time by pressing the LIGHTS
button. If the Lights relay is on during the programmed off time, it may be because of freeze
protection.
Note: Once started, superchlorination will run for the programmed number of hours
(Timers Menu/Super Chlorinate Hours) or until you manually turn it off.
Superchlorination may be temporarily interrupted for a programmed spa operation.
2. Press the “>” button repeatedly until “xxx—all” or “xxx—wkend” (where xxx is the parameter
that you want to program) is displayed.
+
>
Lights-CountDn
0:20
3. The display will show whether superchlorination is “on” or “off”.
>
Adjust time s
setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
This menu will appear only if the Aux1 is configured for timeclock. The Aux output will turn
on and off at the designated times. If the Aux relay is off during the programmed on time—
note that some pool equipment (example pressure side pool cleaner) can only be operated
when the filter pump is running and the pool/spa valves are in the pool-only position—the
Aqua Logic will keep the relay off until these other conditions are suitable for operation. If
the Aux relay is on during the programmed off time, it may be because of freeze protection.
Also, manual operation overrides the timeclock.
or
Program a Countdown Timer
1. Press the “MENU” button repeatedly until “Timers Menu” is displayed
3. Use the “+” and “-“ buttons to set the desired timer period.
Note: A setting of 0:00 will display as “manual on/off”. The countdown automatic
turn off function is disabled but manual operation is still permitted. There may be other
automatic or manual operations that prevent the relay/valve from operating—see a
more detailed discussion under Automatic System Operation/Timers Menu/Aux Timeclock
or in Troubleshooting/Diagnostic Information.
23
Aux1-CountDn
0:20
+
>
2. Press the “>” button repeatedly until the “xxx—Timer” (where xxx is the parameter that you
want to program) is displayed.
>
Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15...)
Move to previous/next menu item
This menu will appear only if the Aux1 is configured for countdown timer. This setting is the
time after you manually turn on the Aux relay until the Aqua Logic automatically turns off the
relay. You can also manually turn off the relay at an earlier time by pressing the AUX1 button.
12
For two speed pumps, this setting will be the period of time when the pump runs at high
speed (the word “Filter T1” in the display will be replaced with “Filter Hi”). There is a
separate timeclock for the low speed operation (see “Filter T2” below). If the high speed and
low speed periods overlap, then the pump will operate in low speed during the overlap
period.
There are several reasons the filter pump may be running at times other than the timeclock
period set above. These include super-chlorination, spa operation, manual operation, heater
cooldown, freeze protection and “solar-extend”.
+
>
Filter T2-wkday
8:30A to 4:00P
+
>
Filter T2-wkend
8:30A to 4:00P
+
>
or
SetFilter
Day and
T2-all
Time
Wednesday
8:30A to 4:00P
10:37P
>
Adjust time s
setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
Enter/Exit Service (or Service—Timed) Mode
1. Go to Aqua Logic main unit (normally mounted near the pool equipment)
2. Pressing the “Service” button rotates through normal operation (red LED off), service mode
(red LED on continuously) and service-timed mode (red LED flashing).
Note: This operation can only be performed at the main Aqua Logic unit. Both “Service” and “Service-Timed” disable all automatic programmed operations and allow
manual operation from the main unit only. The buttons on the remote display/keypads
will still be able to turn equipment off in case of an emergency, but will not turn any
equipment on. If the system is in “Serviced-Timed” it will automatically switch back to
normal operation at the end of the 3 hour time period.
For one speed pumps, this is the second filter timeclock
For two speed pumps, this timeclock will set the normal time period for filter pump low speed
operation (the word “Filter T2” in the display will be replaced with “Filter Lo”). If the filter
pump was off prior to the start of this time period, the filter pump will first turn on at high
speed for 3 minutes to prime and establish water flow. Afterwards, it will drop down to low
speed for the remainder of the programmed low speed time period. While this time clock will
override the high speed timeclock (see above), there are several reasons why the pump will
automatically switch to high speed operation during this programmed time period. These
include manual operation, spa operation, or heating operation. Refer to page 10 for general
notes regarding timeclock programming.
+
>
Spa-wkday
6:00P to 9:00P
+
>
Spa-wkend
6:00P to 9:00P
+
>
or
Set Day
Spa-all
and Time
Wednesday
6:00P to 9:00P
10:37P
>
Adjust time s
setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
This menu is only available if the system has been setup for “spa only” or “pool and spa”.
During the programmed spa time, the Aqua Logic will turn on the filter pump and move the
pool/spa valves into the “spa-only” position. The heater will automatically heat the spa up
to the programmed spa temperature (page 7). This programmed spa operation will take
precedence over all other automatic functions, only manual operation of the filter button or
pool/spa valve button will override this function.
If your pool has a separate jet pump or blower controlled by Aux1 and/or Aux2 , you will have
to program those separately (see page 12).
11
24
During this procedure the wireless remote “learns” and remembers the ID code for the
wireless base station connected to this particular Aqua Logic unit and will reject messages
with any other ID codes. If “Base NOT found” is displayed, then the Aqua Logic can not
communicate with the transmitter/receiver base station attached to the main unit. If “NOT
Successful” is displayed, then the base station did not receive a signal from the remote
control. This may be due to the distance between the Base Receiver and the remote device
being too great or may be due to interference caused by other RF equipment operating in the
neighborhood. Try changing the channel and then repeat the “Teach Wireless” command.
Salt is required only if you are using the chlorinator features on the Aqua Logic Control. If you are NOT
using the chlorinator, it is recommended that you follow all of the other chemistry recommendations besides salt. Refer to the description of the Aqua Logic configuration menu for information on enabling/
disabling the chlorinator (see page 14).
Wireless
Channel: 1
Water Chemistry
The table below summarizes the levels that are recommended by the Association of Pool and Spa Professionals (APSP). The only special requirements for the Aqua Logic are the salt level and stabilizer.
Confirm Change:
+ to proceed
Reteach all
wireless units
>
>
>
>
General Water Chemistry
>
>
Chlorinator Operation / Water Chemistry
>
Change the desired wireless channel (1 - 5)
If channel is changed, move to confirmation menu
If channel is not changed, move to previous/next menu item
Push to confirm the channel change
Move to previous/next menu item
>
Move to previous (Teach Wireless) menu
+
+
This setting changes the channel to be used by the wireless base station and remote(s). If
the channel is changed and confirmed, all of the wireless remotes will have to be retaught.
This menu will only appear if a wireless base station is connected to the Aqua Logic.
Timers Menu
The Timers Menu allows you to set all timeclock and countdown timers which control the automatic
operation of your pool/spa system.
Each timeclock has a single on/off program per day. All of the timeclocks are setup (Configuration Menu)
either as “all days” or “weekends/weekdays”. If “weekends/weekdays” are selected, you will need to
program on times for both weekdays and weekends and off times for both weekdays and weekends, even
if you want them to be the same. All times are adjusted in 15 minute increments (9:00A, 9:15A, 9:30A,
etc.). If you program the on time equal to the off time (“10:00A to 10:00A”) the output will NEVER turn
on. If you want to disable a timeclock, you can set the on time equal to the off time and you will notice the
times disappear and the display simply shows “Off”. If, at a later time, you wish to re-activate the timeclock,
simply press either the “+” or “-” buttons to go back to a normal timeclock programming display.
Saturation index
The saturation index (Si) relates to the calcium and alkalinity in the water and is an indicator of the pool
water “balance”. Your water is properly balanced if the Si is 0 ±0.2. If the Si is below -0.2, the water is
corrosive and plaster pool walls will be dissolved into the water. If the Si is above +0.2, scaling and
staining will occur. Use the chart below to determine the saturation index.
The Countdown timer is programmed in increments of 5 minutes from “Manual On/Off” (0 minutes) to a
maximum of “21:00” (21 hours). When “Manual On/Off” is displayed, the countdown timer is disabled
and the output will be manually controlled. When a countdown timer is equal or greater than “0:05”,
pressing the appropriate output button will turn the output on and start the timer. Pressing the button again
will turn the output off or, when the programmed time has elapsed, the output will automatically turn off.
Si = pH + Ti + Ci + Ai - 12.1
12
53
.3
Calcuim
Hardness
Ci
75
100
125
150
1.5
Total
Alkalinity
1.6
1.7
1.8
16
60
.4
19
66
.5
24
76
.6
200
250
29
84
.7
300
1.9
2.0
2.1
34
94
.8
39
103
.9
400
600
800
2.2
2.4
2.5
Ai
75
100
125
150
1.9
200
250
300
2.3
2.4
2.5
400
600
800
2.6
2.8
2.9
2.0
2.1
2.2
How to use: Measure pool pH, temperature, calcium hardness,
and total alkalinity. Use the chart above to determine Ti, Ci,and
Ai from your measurements. Insert values of pH, Ti, Ci and Ai
into the above equation. If Si equals .2 or more, scaling and
staining may occur. If Si equals -.2 or less corrosion or irritation
may occur.
-.2
0
CORROSIVE
.2
SCALING
or
SetFilter
Day and
T1-all
Time
Wednesday
8:30A to 4:00P
10:37P
Filter T1-wkend
8:30A to 4:00P
Filter T1-wkday
8:30A to 4:00P
+
+
+
>
Ti
>
ºF
>
ºC
>
Adjust time s
setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
>
Adjust time setting
Move between start and stop times & to previous/next menu item
For one speed pumps, this is the first filter timeclock and will determine the normal hours of
filtration for the pool. For pool/spa combination systems with spillover enabled, the valves
will automatically switch to spillover mode at the start of the filtration period. For all other
systems, the valves will switch to the pool-only position. Refer to the text above for general
notes regarding timeclock programming.
OK
25
10
+
>
Set Day and Time
Wednesday 10: P
+
>
Set Day and Time
Wednesday
37
+
>
Set Day and Time
Wednesday 10:37P
>
Adjust the current day of the week
Move to hours setting
>
Adjust the current hour (including AM/PM, if applicable)
Move to minutes setting
>
Adjust the current minute
Move to previous/next menu item
Use this function to set the current day of the week and time. These values are used for all
the automatic timeclock functions of the Aqua Logic and are also displayed as part of the
default menu.
The Aqua Logic is designed to keep the clock running during power outages lasting less
than 7 days. If power has been off for longer than 7 days, then the time may have to be reset.
+
>
Display Light
On for 60 sec.
>
Toggle between Always On and On for 60 sec.
Move to previous/next menu item
This function controls the backlight on the display. If the “60 seconds” option is selected,
then the backlight will automatically turn off 60 seconds after the last key is pressed and will
stay off until next time a key is pressed.
Note that the Display Light selection only applies to the display keypad that you are currently
using. Other display/keypads will not be affected. In other words, you need to individually
set this option for each display/keypad in the system.
+
>
Beeper
Enabled
>
Toggle between Beeper Enabled (default) and Disabled
Move to previous/next menu item
When “Enabled”, the keypad will beep every time a key is pressed. If this is not desired,
select “Disabled”.
This function only applies to the display/keypad that you are currently using. You need to
set this option for each display/keypad in your system.
NOTE: This function is not supported on all display/keypads. If the “Enabled” selection is
not blinking, then the current software revision of that particular keypad/display does not
support the option and it will default to Beeper Enabled.
+
Teach Wireless
+ to start
>
Press and hold
wireless button
Press any button on wireless remote
Move to previous/next menu item
>
Move to previous/next menu item
>
Teach Wireless
Base NOT Found
>
>
Teach Wireless
NOT Successful
Push to start process
Move to previous/next menu item
>
Teach Wireless
Successful
>
>
Move to previous/next menu item
The pool’s chemistry must be balanced BEFORE activating the Aqua Logic’s optional chlorinator function. NOTE: If the pool does not have new water, add metal remover and non-copper based algaecide
to the pool, per manufacturer’s instructions. This ensures a quick, troublefree transfer to the Aqua Logic
system.
Salt (When using optional chlorinator function - requires AQL-CL chlorination kit)
Salt Level
Use the chart on the following page to determine how much salt in pounds or (Kgs) should be added to
reach the recommended levels. Use the equations below (measurements are in feet/gallons and meters/
liters) if pool size is unknown.
Liters
Gallons
Length x Width x
Average Depth x 1000
Round
Diameter x Diameter x
Average Depth x 5.9
Diameter x Diameter x
Average Depth x 785
Oval
Length x Width x
Average Depth x 6.7
Length x Width x
Average Depth x 893
The operating salt level is between 2700-3400 PPM (parts per million) with 3200 PPM being optimal.
Before adding any salt, test the salt level. This is especially important for retrofit installation to older pools
where chlorine added to the pool over time has ended up as salt. If the level is low, determine the number
of gallons in the pool and add salt according to the chart below. A low salt level will reduce the efficiency
of the sanitization and result in low chlorine production. A high salt level can cause the Aqua Logic to stop
chlorinating. The salt in your pool/spa is constantly recycled and the loss of salt throughout the swimming
season should be minimal. This loss is due primarily to the addition of water because of splashing,
backwashing, or draining (because of rain). Salt is not lost due to evaporation.
Type of Salt to Use
It is important to use only sodium chloride (NaCl) salt that is greater than 99.0% pure. This can be found
at most pool stores in 40-80 lb. bags labeled “for use in swimming pools”. Alternatively, use common food
quality or water softener salt that is at least 99.0% pure. It is also acceptable to use water conditioning salt
pellets, however, it will take longer for them to dissolve. Do not use rock salt, or salt with more than 1%
of yellow prussiate of soda, salt with anti-caking additives, or iodized salt.
How to Add Salt
For new plaster pools, wait 10-14 days before adding salt to allow the plaster to cure. Turn the circulating
pump on and add salt directly into the pool. Brush the salt around to speed up the dissolving process—do
not allow salt to pile up on the bottom of the pool. Run the filter pump for 24 hours with the suction coming
from the main drain (use pool vacuum if there is no main drain) to allow the salt to evenly disperse throughout the pool. The salt display may take 24 hours to respond to the change in salt concentration.
Always check stabilizer (cyanuric acid), when checking salt. These levels will most likely decline together.
Use the chart on page 28 to determine how much stabilizer must be added to raise the level to 80 ppm.
This menu will only appear if a wireless base station is connected to the Aqua Logic. Perform
this procedure each time a wireless remote control is added to the Aqua Logic system.
9
(pool size in meters)
(pool size in feet)
Rectangular Length x Width x
Average Depth x 7.5
26
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
Dilute
3600+
>
Turn super chlorinate on or off
Move to previous/next menu item
This setting will only appear if “chlorinator” is enabled. When you have an unusually high
bather load, a large amount of rain, a cloudy water condition, or any other condition that
requires a large amount of chlorine to be introduced to the pool, activate the Aqua Logic
Super-Chlorinate function. The Aqua Logic will turn on the filter pump, set the pool/spa
valves to the correct position, and set the chlorine generator to maximum output. The
superchlorinate function will continue for the programmed number of hours (see Timers/
Super Chlorinate Hours below) overriding the normal filter pump timeclock settings. At the
end of the super chlorinate period, the pool will return to normal operation.
Dilute
Dilute
Dilute
OK
OK
OK
OK
OK
OK
OK
OK
OK
Dilute
OK
3400
OK
OK
OK
OK
Ideal
Ideal
Ideal
Ideal
Ideal
Ideal
Ideal
Ideal
3200
(12)
(11)
(9)
(8)
(6)
3000
Ideal
(15)
(14)
OK
OK
OK
Ideal
Ideal
Ideal
Ideal
Ideal
Ideal
Ideal
(24)
(23)
(21)
(20)
(18)
47
(17)
(42)
(39)
43
(36)
40
33
(33)
37
(30)
(27)
30
27
(24)
(21)
23
17
13
20
(18)
(15)
(12)
2800
Ideal
67
(30)
(29)
(26)
(27)
63
(60)
(57)
60
50
57
(48)
53
(45)
(51)
(54)
(90)
127
120
113
107
100
93
87
80
73
67
60
47
33
27
40
53
(45)
90
80
(36)
(32)
(23)
2600
50
40
(18)
60
(27)
93
80
(36)
67
(30)
53
(24)
2400
(41)
(50)
110
100
(55)
120
(59)
(64)
140
130
(68)
(73)
160
150
(77)
170
(81)
(86)
190
180
133
200
(123)
267
(117)
253
(110)
240
187
(42)
(48)
107
(55)
(61)
(67)
147
133
120
(73)
160
(79)
(85)
173
(91)
(98)
213
200
227
(104)
(144)
(121)
233
167
83
(38)
2200
(30)
67
100
(45)
(53)
117
133
(61)
150
(83)
183
(76)
(68)
(91)
200
(98)
(106)
217
250
267
(114)
283
(129)
(137)
333
(152)
400
340
320
(145)
300
(136)
280
(127)
240
(91)
220
200
(82)
(73)
(64)
140
(45)
120
100
80
2000
(36)
(55)
160
180
(100)
(109)
260
(169)
(118)
397
(180)
373
350
(159)
327
(148)
303
(117)
233
(106)
(95)
(85)
(74)
163
(53)
140
117
93
1800
(42)
(64)
187
210
257
280
(127)
(138)
453
(207)
427
(195)
400
(182)
373
(170)
347
320
293
(133)
267
(121)
240
(97)
(85)
187
(61)
160
133
(48)
1600
107
(73)
213
(109)
(145)
(158)
510
(232)
480
(218)
450
(205)
420
(191)
390
330
(150)
300
(136)
270
(109)
(95)
210
180
(82)
(68)
150
120
1400
(55)
240
(123)
360
(164)
(177)
567
(258)
533
(243)
500
(227)
467
(212)
433
400
367
(167)
333
(152)
267
300
(106)
233
(76)
(91)
167
(61)
1200
133
200
(121)
(136)
(182)
(197)
623
(283)
587
(267)
550
513
(233)
477
440
403
(183)
367
(167)
330
(117)
293
257
(83)
220
183
(67)
1000
147
(100)
(133)
(150)
(200)
(217)
(250)
(154)
317
467
(211)
443
(201)
420
(190)
300
533
(243)
507
(231)
480
(219)
(181)
600
(263)
570
(259)
540
(246)
380
667
(304)
633
(289)
600
(274)
(172)
733
(333)
697
(317)
660
(300)
360
800
(364)
760
(346)
720
(328)
680
(310)
640
(291)
600
(273)
560
(255)
520
(236)
480
440
(200)
400
(182)
360
320
280
(127)
240
200
(91)
(73)
800
160
(109)
(145)
(164)
(218)
607
(276)
563
(256)
520
477
(217)
433
(197)
390
347
303
(138)
(118)
217
(98)
173
600
(79)
260
(158)
(177)
(236)
(297)
(276)
(127)
(106)
400
(85)
(148)
(170)
(233)
(212)
(191)
(255)
653
607
560
513
467
420
373
327
280
233
187
(163)
867
(398)
823
(378)
780
(358)
693
(317)
650
(297)
737
(339)
(318)
(337)
(403)
(382)
933
(424)
887
840
(360)
(430)
(408)
747
700
793
(363)
(318)
(250)
(227)
(182)
(159)
(136)
(114)
200
(91)
350
250
200
300
400
550
500
450
(205)
(273)
(295)
800
700
600
650
750
(341)
(385)
(453)
(484)
950
900
850
1000
1067
(460)
960
(436)
907
(412)
854
(388)
800
(364)
747
(339)
693
(315)
640
(291)
587
(267)
(242)
480
(218)
427
(194)
373
(97)
(170)
320
(145)
267
(121)
213
0
8,000 10,000 12,000 14,000 16,000 18,000 20,000 22,000 24,000 26,000 28,000 30,000 32,000 34,000 36,000 38,000 40,000
(30,000) (37,500) (45000) (52,500) (60,000) (67,500) (75,000) (82,500) (90,000) (97,500) (105,000) (112,500)(120,000)(127,500)(135,000)(142,500)(150,000)
ppm
+
If you manually turn off the filter pump (using the “Filter” button on any display/keypad),
the super chlorinate function terminates. When you turn the filter pump back on, super
chlorinate will resume for the balance of the programmed number of hours.
Spa Chlorinator
3%
+
>
Adjust the desired chlorinator output for spa (0,1,2,3...9,10,15,20...95,100%)
Move to previous/next menu item
This setting will appear only if the system has been setup for “chlorinator” and “spa only”
or “pool and spa”. It will determine the chlorinator output when the system is operating in
spa-only mode. The actual amount of chlorine introduced into the spa is determined by: this
setting, the amount of time the pool operates in spa-only mode, the water temperature, and
the amount of salt in the water. If the filter pump is running due to the freeze protection
feature, then the chlorinator will not operate during this time.
Pool Chlorinator
60%
+
>
POUNDS and (Kg) OF SALT NEEDED FOR 3200 PPM
Gallons and (Liters) of Pool/Spa water
Super Chlorinate
On
>
Current salt
level
>
Adjust the desired pool temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off)
Move to previous/next menu item
The pool solar setting will only appear if the system has been setup for “pool only” or “pool
and spa” operation and the solar control is enabled. The solar system will turn on whenever
the pool/spa valves are in the “pool only” or “spa spillover” position and the filter pump is
running and the pool water temperature is less than the desired temperature setting and solar
heat is available.
>
27
+
>
Pool Solar
88°F
>
Adjust the desired chlorinator output for pool (0,1,2,3...9,10,15,20...95,100%)
Move to previous/next menu item
This setting will appear only if the system has been setup for “pool only” or “pool and spa”.
It will determine the chlorinator output when the system is operating in pool-only or spa
spillover modes. The actual amount of chlorine introduced into the pool is determined by:
this setting, the amount of time the filter pump is running, the water temperature, and the
amount of salt in the water. If the filter pump is running due to the freeze protection feature,
then the chlorinator will not operate during this time.
8
7
1.8
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
80 ppm
(1.5)
3.3
3.2
(1.4)
(1.3)
3.0
2.8
(1.3)
(1.2)
2.7
2.5
(1.2)
(1.1)
2.3
2.2
2.0
(1.0)
(.77)
1.7
1.5
(.68)
(.64)
1.4
1.2
(.54)
0.8
(.54)
0.7
70 ppm
(.45)
1.0
(.82)
(.91)
(2.0)
(1.8)
(1.7)
(1.5)
(1.4)
(1.2)
(1.1)
(.91)
(1.1)
(.91)
(.45)
6.7
(3.0)
(2.6)
(2.4)
(2.3)
(2.1)
4.3
4.0
4.7
(3.2)
(2.9)
(2.7)
3.7
(2.5)
(2.3)
3.3
3.0
(2.0)
(1.8)
2.7
2.3
(1.6)
1.7
1.3
(1.4)
(1.6)
(1.4)
60 ppm
2.5
2.0
2.0
6.0
(3.6)
(3.3)
5.5
5.0
(3.0)
4.5
(2.7)
(2.4)
4.0
3.5
(2.1)
(2.1)
(1.8)
3.0
(1.8)
(2.8)
(4.5)
6.3
(4.3)
(4.1)
5.7
(3.9)
(3.4)
5.3
(3.6)
8.5
(4.8)
8.0
7.5
7.0
6.5
(4.5)
(4.2)
(3.9)
5.0
10.0
(6.0)
(5.7)
9.5
9.0
(5.4)
(6.3)
(6.0)
10.7
10.0
(5.6)
(5.2)
9.3
8.7
(4.9)
(4.5)
8.0
7.4
(4.2)
(3.8)
6.7
6.0
(3.4)
(3.0)
5.4
4.7
(2.7)
3.3
4.0
(2.3)
(2.7)
2.7
40 ppm
4.0
4.2
(2.3)
5.0
3.3
30 ppm
28
50 ppm
(7.5)
13.3
12.7
(7.1)
(6.7)
12.0
(9.0)
16.7
15.8
14.2
13.3
12.5
11.7
10.8
10.0
9.2
8.4
7.5
6.7
5.9
(7.2)
16.0
(6.8)
15.0
(6.4)
14.0
(5.9)
13.0
(5.4)
12.0
(5.0)
11.0
(4.5)
10.0
9.0
(2.2)
8.0
(3.6)
7.0
(3.2)
6.0
(2.7)
(2.7)
20 ppm
5.8
(3.7)
15.0
20.0
(8.6)
19.0
(8.1)
18.0
(10.5)
23.3
22.2
(10.0)
(9.5)
21.0
19.8
(9.0)
(8.5)
18.7
17.2
(8.0)
(7.4)
16.4
15.2
(6.9)
(6.4)
14.0
12.9
(5.9)
(5.3)
11.7
10.5
9.4
(4.3)
7.0
(3.2)
8.2
(3.7)
(4.8)
26.7
(12.0)
25.3
(11.5)
22.7
(10.3)
(9.7)
21.3
(9.1)
20.0
(8.5)
18.7
(7.3)
16.0
(6.7)
14.7
(6.1)
13.4
(4.9)
(5.4)
12.0
10.7
9.4
4.7
The spa solar setting will only appear if the system has been setup for “spa only” or “pool
and spa” operation and the solar control is enabled. The solar system will turn on whenever
the pool/spa valves are in the “spa only” position and the filter pump is running and the spa
water temperature is less than the desired temperature setting and solar heat is available.
(3.2)
>
Adjust the desired spa temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off)
Move to previous/next menu item
10 ppm
+
>
Spa Solar
104°F
(4.3)
The pool heater setting will only appear if the system has been setup for “pool only” or “pool
and spa” operation and the heater control is enabled. The heater will turn on whenever the
pool/spa valves are in the “pool only” or “spa spillover” position and the filter pump is
running and the pool water temperature is less than the desired temperature setting. If you
have both solar heat and a conventional heater and the solar priority option is selected
(Configuration Menu), then the conventional heater will only operate when solar heat is
NOT available.
8.0
>
Adjust the desired pool temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off)
Move to previous/next menu item
(3.6)
+
>
Pool Heater1
Off
6.7
The spa heater setting will only appear if the system has been setup for “spa only” or “pool
and spa” operation and the heater control is enabled. The heater will turn on whenever the
pool/spa valves are in the “spa only” position and the filter pump is running and the spa
water temperature is less than the desired temperature setting. If you have both solar heat
and a conventional heater and the solar priority option is selected (Configuration Menu),
then the conventional heater will only operate when solar heat is NOT available.
(4.3)
>
Adjust the desired spa temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off)
Move to previous/next menu item
5.3
+
>
Spa Heater1
102°F
(3.6)
The Settings Menu allows you to set all system operating parameters except the timeclock and countdown
timers which are part of the Timers Menu.
POUNDS and (Kg) OF STABILIZER (CYANURIC ACID) NEEDED FOR 80 PPM
Settings Menu
0 ppm
The “Diagnostic Menu” is primarily intended for the service technician and contains information and details
about the system operation that are helpful in troubleshooting, if problems occur.
Gallons and (Liters) of Pool/Spa water
The Settings Menu and the Timers Menu are the menus you will be using most often to adjust the operation
of your pool. The Configuration Menu is used when the system is installed and defines what equipment is
connected to each output and the operational logic that will control the equipment. This menu is normally
“locked” and should only be used by a pool professional. Details regarding the Configuration menu are
included in both the Operation and the Installation Manual.
Current
8,000 10,000 12,000 14,000 16,000 18,000 20,000 22,000 24,000 26,000 28,000 30,000 32,000 34,000 36,000 38,000 40,000
Stabilizer
Level (ppm) (30000) (37500) (45000) (52500) (60000) (67500) (75000) (82500) (90000) (97500) (105000) (112500)(120000) (127500)(135000) (142500) (150000)
The Default Menu is a series of informative displays (temperatures, salt levels, chlorinator settings, etc.)
with nothing to set. The Aqua Logic will automatically switch to the default menu when no keys have been
pressed for 2 minutes and will then scroll through each display.
System Maintenance
To maintain maximum performance, it is recommended that you open and visually inspect the cell every 3
months or after cleaning your filter. The Aqua Logic will remind you to do this by displaying the message
“Inspect/Clean Cell” after approximately 500 hours of operation.
Programming Menu Flowchart
The Aqua Logic’s five menus have many items in each menu that allow you to customize the operation of
your pool/spa equipment. The chart below shows the Aqua Logic’s five menus as well as each menu’s
specific settings
The Aqua Logic electrolytic cell has a self cleaning feature incorporated into the electronic control’s logic.
In most cases this self cleaning action will keep the cell working at optimum efficiency. In areas where
water is hard (high mineral content) or in pools where the water chemistry has been allowed to get “out of
balance”, the cell may require periodic cleaning.
denotes conditional items
Servicing and Cleaning the Turbo Cell
Turn off power to the Aqua Logic before removing the electrolytic cell. Once removed, look inside the cell
and inspect for scale formation (light colored crusty or flaky deposits) on the plates and for any debris
which has passed through the filter and caught on the plates. If no deposits are visible, reinstall. If deposits
are seen, use a high pressure garden hose and try to flush the scale off. If this is not successful, use a plastic
or wood tool (do not use metal as this will scratch the coating off the plates) and scrape deposits off of
plates. Note that a buildup on the cell indicates that there is an unusually high calcium level in the pool (old
pool water is usually the cause). If this is not corrected, you may to have to periodically clean the cell. The
simplest way to avoid this is to bring the pool chemistry to the recommended levels as specified.
Mild Acid Washing: Use only in severe cases where flushing and scraping will not remove the majority
of deposits. To acid wash, turn off power to Aqua Logic. Remove cell from piping. In a clean plastic
container, mix a 2:1 solution of water to muriatic acid (one gallon of water to two quarts of muriatic acid).
ALWAYS ADD ACID TO WATER - NEVER ADD WATER TO ACID. Be sure to wear rubber gloves
and appropriate eye protection. The level of the solution in the container should just reach the top of the
cell so that the wire harness compartment is NOT submerged. It may be helpful to coil the wiring before
immersing the cell. The cell should soak for a few minutes and then rinse with a high pressure garden hose.
If any deposits are still visible, repeat soaking and rinsing. Replace cell and inspect again periodically.
PS-4 only
Winterizing
The Aqua Logic electrolytic cell and flow detection switch will be damaged by freezing water just as your
pool plumbing would. In areas of the country which experience severe or extended periods of freezing
temperatures, be sure to drain all water from the pump, filter, and supply and return lines before any
freezing conditions occur. The electronic control is capable of withstanding any winter weather and should
not be removed.
If you are in an area that only experiences occasional freezing conditions, your Aqua Logic system may be
set up to circulate the pool water whenever the air sensor drops to the selected freeze temperature threshold. Make sure the air sensor is recording the correct temperature and is NOT located in the direct
sunlight to ensure proper freeze protection operation.
Spring Start-up
When first starting the pool in the spring time, it is highly recommended that you temporarily set the pool
and spa chlorinator settings (Pool Sanitizer & Spa Sanitizer in the Settings Menu) to 0% (off) and then
manually shock the pool with any chlorine based shock product and balance the pool water chemistry per
the levels indicated in the Chlorinator Operation section (page 25). Make sure to check the salt and
stabilizer levels and bring them up to the recommended levels. Your local Authorized Aqua Dealer or pool
store can recommend the best chemical treatment for your pool. After the water is clear and balanced,
then go back and adjust the pool and spa chlorinator settings to the appropriate levels. Test the pool
chlorine level weekly and adjust the chlorinator settings up or down accordingly.
It is usually a good idea to also inspect the cell and clean if necessary at the start of the season. See
instructions above.
29
PS-4 only
6
Automatic System Operation
The Aqua Logic controls most of your pool equipment automatically in order to minimize the time spent
working on your pool. Most of the pool equipment can be programmed to operate on a timeclock basis.
In addition, the desired pool and spa temperatures and pool and spa chlorinator settings can be programmed. This section will guide you on how to program the automatic operation for each function.
The programming of automatic functions can be performed at either the main display/keypad located at the
pool equipment pad or the in-home remote display/keypad.
Using the programming buttons
There are 5 buttons on each keypad that are used for programming (refer to diagram).
Display
Troubleshooting and Diagnostic Information
The Aqua Logic provides 2 different tools to aid in troubleshooting any problems that may occur in your
pool and/or spa system. The Service mode will allow you to disable automatic operation and manually
control most of the equipment (the heater and general purpose Valve3 output are the exceptions). The
Diagnostic Menu will provide some detailed information regarding system operation.
While both of the features are primarily intended for the use of the professional service technician, their
function is fully explained below. If you believe your system is not operating properly or have questions
regarding the operation, call the Goldline Technical Service Department from Monday through Friday,
8AM to 8PM EST at 888-921-7665.
Service Mode
The main unit keypad has a SERVICE button that is used primarily during servicing of the pool equipment.
If you want to completely disable the automatic operation and operate the system manually, you can put
the system into Service or Service-Timed mode by pressing the “Service” button. Pressing the “SERVICE” button once will switch the system into service mode which means that all automatic functions are
disabled, the optional remote display/keypads are disabled (except for manual turn off for emergencies).
The outputs can be manually controlled by pressing the buttons on the local display/keypad. The red
“SERVICE” LED will be illuminated and the Aqua Logic will remain in this mode of operation until manually taken out of service mode.
Settings
Menu
Menu Button
Select Desired Menu
+
Pressing the “SERVICE” button again will cause the Aqua Logic to switch to service-timed mode which is
very similar to service mode, except that the Aqua Logic will automatically return to normal operation after
3 hours. During service timed operation, the “SERVICE” LED will flash and the time remaining will be
displayed on the remote display/keypad(s).
>
Menu
>
“<” and “>” Buttons
Select Items from
a Menu
“+” and “-” Buttons
Adust
Pressing the “SERVICE” button again, will return the Aqua Logic to normal (automatic) operation.
There are 4 steps to programming any function:
1.
Menu
Press the “MENU” button to get to the desired menu. Multiple pushes of the
button will rotate through all 5 menus and return to the starting point.
2.
>
>
Press either key to scroll through the various items in the selected menu. Multiple
pushes of the button will rotate through all menu items and return to the starting
point. Only menu items that are applicable to your pool will appear. (Example: if
you don’t have a spa, then no spa related menu items will appear).
3.
+
>
4.
Once a menu item has been selected above, the current setting/selection will appear (flashing) on the display. Use the “+” and/or “-” keys to change this selection. Sometimes “+” and “-“ will adjust a value up or down (example: heater
temperature setting or timeclock on/off time). In this case, pushing the “+” or “-”
will change the value by one increment and holding the “+” or “-” button in for
more than one second will make the values auto scroll. In other cases, the “+” and
“-“ may toggle between 2 options (example: turning superchlorination ON or
OFF).
>
Menu
After you have adjusted the item to the desired value, simply move on to the next
menu item to “lock in” your new setting. The Aqua Logic memory will maintain
the setting, even if power is removed for an extended period.
5
30
Lights, Aux1 and Aux2 Outputs
Check System Indicator
The “CHECK SYSTEM” LED will alert you when the Aqua Logic detects any of the following conditions
that are abnormal and require attention for optimal operation of your pool.
• Inspect Cell -- for optimum operation, you will need to inspect the Aqua Logic chlorinator cell approximately every 3 months and clean the cell if necessary. The Aqua Logic will automatically remind
you when it is time and display “Inspect Cell, + to reset” as part of the rotating Default Menu. Clean the
cell (see instructions, page 29) and then press the “+” button during the “Inspect Cell” display to reset
the timer.
• Low Salt/Minerals or Very Low Salt/Minerals -- when the salt is too low the Aqua Logic will
generate less chlorine and the life of the cell is degraded. Check the cell and clean if necessary (see
instructions, page 29) before adding salt (see instructions, page 26).
• High Salt/Amps/Minerals -- the Aqua Logic will stop generating chlorine under certain high salt
conditions in order to protect the internal electronics from damage. The only way to lower the salt level
is to partially drain the pool and add fresh water.
Standard Relay: Manual operation of all 3 relays is identical. Assuming that the relay is currently off,
simply press the appropriate button to turn on the relay. If the relay does not turn on, it probably is due to
the “interlock” feature (which was set up in the Configuration Menu) being activated that requires the filter
pump to be running and the valves to be in the pool-only position. This protects pumps and other equipment from possible damage. If the controlled output is on, pressing the appropriate button again will turn
off the relay. Manual turn off is disabled if the “Freeze Protection” feature is enabled and the air temperature is less than the selected freeze temperature threshold.
Dimmer Relay: If Lights or an Aux output is configured as a dimmer, pressing the corresponding button
will generate a temporary display which shows the dimmer output level (Off - On 100%). Pushing the “+”
or “-” button changes the level in increments of 20%. When the desired output level is displayed, press the
corresponding button again to turn off the display and return to normal operation. When the Lights or Aux
output comes on again (either manually or automatically), the dimmer output level will be the same as the
last time that it was set.
Pool/Spa Valves
• Water Sensor -- if the water sensor is either an open or short circuit.
Pool-only or spa-only systems: The POOL/SPA button has no function.
• Air sensor -- if the freeze protection feature is enabled (Configuration Menu/ Filter Config.) and the air
sensor is either an open or short circuit.
Pool and Spa systems without spa spillover: In pool-only mode, the left LED next to the POOL/SPA
button is illuminated. Pressing the POOL/SPA button will switch the AQL-P-4 to spa-only operation
(right LED illuminated). Pressing the POOL/SPA button again will switch back to pool-only. Note that
the filter pump will turn off while the pool/spa valves are turning.
• Solar Sensor -- if the solar sensor is either an open or short circuit.
• Chlorinator Cell Sensor -- if the chlorinator function is enabled (Configuration Menu/Chlorinator)
and the cell sensor is either an open or short circuit.
• Low Volts -- if the chlorinator cell voltage is too low.
• No Cell Power -- if no chlorinator cell power is detected on the printed circuit board.
• Check Flow Switch -- if the flow switch input is invalid.
• Cell Power Error -- if a chlorinator cell power error is detected on the printed circuit board.
• Cell Missing -- if the chlorinator is enabled but no cell is detected.
For helpful troubleshooting information on any of these issues, go to the Diagnostic Menu and then scroll
through the various items until you see the cause for the “CHECK SYSTEM” LED being illuminated.
Pool and Spa systems with spa spillover: In pool-only mode, the left LED next to the POOL/SPA
button is illuminated. Pressing the POOL/SPA button will switch the AQL-P-4 to spa-only operation
(right LED illuminated). Pressing the POOL/SPA button again will switch to spa spillover operation (both
LED’s illuminated). Pressing the POOL/SPA button again will switch back to pool-only. Note that the
filter pump will turn off while the pool/spa valves are turning.
Service
The main unit keypad has a SERVICE key. This button is used primarily during servicing of the pool
equipment. If you want to completely disable the automatic operation and operate the system manually,
you can put the system into Service or Service-Timed mode by pressing the SERVICE button. Pressing
the SERVICE button once will switch the system into service mode which means that all automatic functions are disabled, and the remote display/keypads are disabled (except for manual turn off for emergencies). The red SERVICE LED will be illuminated and the Aqua Logic will remain in this mode of operation
until manually taken out of service mode.
Pressing the SERVICE button again will cause the Aqua Logic to switch to service-timed mode which is
very similar to service mode, except that the Aqua Logic will automatically return to normal operation after
3 hours. During service timed operation, the “Service” LED will flash and the time remaining will be
displayed on the remote display/keypad(s).
Pressing the SERVICE button again, will return the Aqua Logic to normal (automatic) operation. See
Troubleshooting/Diagnostic Information (page 30) for more information about the service modes.
31
4
Diagnostic Menu
+23.45
Set Day and
+6.75A
Time
Wednesday
84°F
3200PPM
10:37P
(Pool/Spa/Spillover)
Filter Pump
Filter
Check System
Indicator
If the current (amps) display is 0.00A, then the chlorinator is operating normally but is in the
off part of its normal operating cycle. Simply press either the “+” or “-“ key to start a new
cycle.
(On/Off)
Pool/Spa
Lights
The Aqua Logic periodically reverses the polarity of the voltage applied to the cell in order
to automatically clean off any calcium deposits. It is important that you check the chlorinator
operation in both polarities. To do this, press either the “+” or “-“ buttons and the chlorinator
will turn off, wait for 15 seconds and then turn on in the opposite polarity.
(On/Off)
Lights
Service
Aux 1
Aux 2
Service Button
Aux 1
(On/Off)
If a conventional or solar heater is operating, it is likely that the temperature of the water at
the cell is higher than the pool/spa water temperature displayed on the Aqua Logic default
display.
Aux 2
(On/Off)
(main display only)
Filter Pump
Single Speed Filter Pump: If the pump is currently off, press the FILTER button to turn on the pump.
Pressing the FILTER button again will turn off the pump. However, if there is a heater in the system, and
it is operating, and the “Heater Cooldown” feature is enabled (Configuration Menu) then: when you press
the FILTER button to turn off the filter, only the heater will turn off, the Filter LED will flash and the display
will indicate “Heater Cooldown”. At this point the filter pump will automatically turn off after 5 minutes of
heater cooldown operation. If you want to override the heater cooldown, simply press the FILTER button
again to turn off the filter pump.
Two Speed Filter Pump: If the pump is currently off, simply press the FILTER button to turn on high
speed operation of the filter pump. The “Filter” LED will illuminate continuously. Pressing the FILTER
button again will switch to low speed operation and the “Filter” LED will flash. If you attempt to switch to
low speed shortly after turning on high speed the filter pump will automatically remain in high speed for 3
minutes before switching to low speed to allow the pump to prime and establish normal water flow.
Freeze Protection: This function protects the pool, plumbing, and equipment against freeze damage. If
Freeze Protection is enabled and the AIR temperature sensor falls below the preset freeze protection
temperature (see Filter Pump Configuration), the Aqua Logic will turn on the filter pump to circulate the
water.
3
Instant Salt
3200 PPM (+=save)
+
>
Press to load the “Instant salt” into the averaged salt display
Move to previous/next menu item
This display will be shown only if the chlorinator is enabled. This display shows “Instant
Salt” or “Instant Minerals” (if Chlor. Config. is set for “Display Minerals”). The “Instant
Salt” is calculated based on the voltage, current (amps), and water temperature at the cell.
This is different than the “average salt” value which is displayed as part of the default menu.
There are a number of reasons why instant and average salt readings may differ. Some of
these include salt having just been added to the pool and not yet thoroughly mixed, calcium
buildup on the cell, and the cell aging.
Flow Switch
Flow
+
>
Valve 3
Indicator
Press to switch chlorinator operation to opposite polarity (15 second delay)
Move to previous/next menu item
This display will be shown only if the chlorinator is enabled. For the chlorinator to be
operating, several other things must be happening: the filter pump must be running, the flow
switch must be detecting flow, the chlorinator setting must be set greater than 0%, the water
temperature at the cell must be between 50ºF and 140ºF, and the salt level must be within the
operating range. If any of these conditions are not met, the chlorinator diagnostic display
will tell you the reason. It’s possible to have more than one reason, in which case after you
rectify what was displayed the first time, a second display will appear.
Pool/Spa Button
Salt Level
3200ppm
>
+/- 23.45V is the voltage applied to the chlorinator cell
+/-6.75A is the current (amps) through the cell
84ºF is the water temperature at the cell
3200PPM is the “instant” salt level at this time
Display
Heater Indicator
+
>
While the main objective of the Aqua Logic is to automate the operation of your pool/spa system, there
may be certain times when you want to override the automatic operation and control the equipment manually. To operate the pool equipment manually while keeping the automation active, perform the following
procedures. Note that if you turn a relay on manually, it will remain on until either you turn it off manually,
or the next time the programmed automatic operation would normally turn that relay off. Example: the
filter pump is programmed to run from 9:00A to 5:00P daily. If you turn the filter pump on manually at
8:00PM, it will run continuously until the next day at 5:00PM at which time it will turn off and follow the
normal program from then on. Manually turning off a relay works in a similar fashion.
To enter the Diagnostic Menu, press the “Menu” button repeatedly until the display shows “Diagnostic
Menu”. At this point, you can use either the “<” or “>” buttons to scroll through the various menu items
which are described below:
>
Manual System Operation
>
No function
Move to previous/next menu item
This display will be shown only if the chlorinator is enabled. The current status of the flow
switch is displayed. There is a short delay when transitioning from flow to no-flow and a
longer delay on the transition from no-flow to flow. The delay time is displayed.
32
+
>
Solar Sensor
Short circuit
+
>
Air Sensor
94ºF
+
>
Water Sensor
Open circuit
+
>
Cell Temp Sensor
77ºF
>
No function
Move to previous/next menu item
>
No function
Move to previous/next menu item
>
No function
Move to previous/next menu item
>
No function
Move to previous/next menu item
Available displays depend on configuration. If the sensor appears to operating properly,
then the temperature will be displayed. If this temperature is not correct then check the
placement of the sensor. If the problem is not placement related, then the sensor will, most
likely, require replacement. If the display is “Open Circuit” or “Short Circuit” then check the
wiring to the sensor and also make sure that the wires are secure in the terminal block in the
Aqua Logic main unit.
+
>
>
No function
Move to previous/next menu item
>
No function
Move to previous/next menu item
>
No function
Move to previous/next menu item
>
No function
Move to previous/next menu item
Available displays depend on configuration. If you call the Goldline Technical Service
Department for assistance, they may ask for the software revisions of both the main unit and
each of the display/keypads or other devices that are attached to the system. Note that it is
possible that different display/keypads have different software revision levels. For this
reason, it is advisable to check this diagnostic menu item on every display.
With the use of the optional AQL-CL chlorination kit, the Aqua Logic is also an automatic chlorine generation system for pool and/or spa sanitization. If enabled (see Configuration Menu), this operation requires
a low concentration of salt (sodium chloride) in the pool/spa water. The Aqua Logic automatically converts the salt into free chlorine which kills bacteria and algae in the pool/spa. Chlorine will revert back to
sodium chloride after killing bacteria. These reactions will continuously recycle, virtually eliminating the
need to add sanitizing chemicals to your pool/spa. The only time you may need to add more salt to the
pool/spa is when water is replenished due to backwashing, draining, or splashing (not evaporation).
The Aqua Logic is designed to handle the purification needs of most residential swimming pools up to
40,000 gallons (150,000 liters), or the needs of most commercial pools up to 25,000 gallons (95,000
liters). Check local codes for other restrictions. The actual amount of chlorination required to properly
sanitize a pool varies due to bather load, rainfall, temperature, and the pool’s cleanliness.
For pools larger than 40,000 gallons, the Aqua Logic can control one or more Goldline Aqua Rite chlorinators to supplement chlorine production.
NOTE: Before installing this product as part of a saline water purification system in a pool or spa using
natural stone for coping or for immediately adjacent patios/decking, a qualified stone installation specialist
should be consulted regarding the appropriate type, installation, sealant (if any) and maintenance of stone
used around a saline pool with electronic chlorine generator in your particular location and circumstances.
Default Display
Turn power on at the main panel and turn the Aqua Logic control power circuit breaker on. The keypad
will show the default display. The default display alternates between the day/time, air and pool (or spa)
temperature, pool/spa sanitizer setting, and salt level. Under certain circumstances, additional displays
may be added to the default menu to inform you about system operation. Refer to the Programming Menu
Flowchart on page 6 to view all possible displays. The Aqua Logic will automatically scroll through all of
the available default menu displays or you can press “<” or “>” to manually scroll.
Saturday
11:45A
Pool/Spa
+
Service
>
6B Spa Software
Remote A r1.00
+
>
RF Base Software
r1.20 ID:1234
+
>
Display Software
remote-08 r3.10
+
>
Main Software
Revision 2.40
Chlorination
33
Menu
Filter
Lights
Aux 1
Aux 2
>
2
System Overview
The following statement is applicable if any of the wireless accessories are connected to the Aqua Logic
system.
The Aqua Logic is a multifunction pool controller used to fully manage your pool/spa system. The Aqua
Logic can control pumps, valves, lighting, heaters, and chlorination. Although the Aqua Logic is easy to
use, it is important to completely read through this operating manual before attempting to operate the
control.
FCC Statement
(Compliance Statement, Part 15.19): This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
WARNING (Part 15.21): Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Optional
Wireless Base
Receiver
Industry Canada Statement
Optional
Remote Display
Keypad
The term “IC” before the certification/registration number only signifies that the Industry Canada technical
specifications were met.
Main Display
Keypad
Interference
(maximum of three)
Filter Pump
Lights
Aux 1
Water
Temperature
Sensors
120/240V
Relays
Aux 2
Pool/Spa Suction &
Return Valves
Air
Solar
24V Valve
Actuators
Valve 3
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, then the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into a power source on different circuit than the receiver.
Consult the dealer or an experienced radio/TV technician for help.
Heater
Optional
Flow Switch
Optional
Chlorinator Cell
240 VAC
Power
Circuit Breaker
Subpanel
NOTE: This manual assumes that the Aqua Logic has been wired and configured according to the Installation Manual. Aspects of the Aqua Logic that pertain to system setup are not covered in this manual.
Automation
The AQL-P-4 can control up to 4 high voltage (120/240V) pieces of equipment, up to 3 automatic valve
actuators, and a conventional and solar heater. Both manual and automatic (programmed) operation are
available. All of the control functions can be programmed at a display/keypad which is part of the main unit
(typically located near the pool equipment) or at one or more remote display/keypads.
1
34
Table of Contents
35
System Overview
Block Diagram.......................................................................
Automation.............................................................................
Chlorination............................................................................
Default Display.......................................................................
1
1
2
2
Manual System
Operation
Filter Pump.............................................................................
Lights and Aux Outputs..........................................................
Pool/Spa Valves.....................................................................
Service....................................................................................
3
4
4
4
Automatic System
Operation
(Programming)
Using the Programming Buttons..........................................
Programming Menu Flow Chart...........................................
Settings Menu........................................................................
Timers Menu..........................................................................
Configuration Menu...............................................................
5
6
7
10
13
Quick “How To”
Guide
Operate the Spa - Manually..................................................
Operate the Spa - Automatically..........................................
Set the Heater Temperature.................................................
Set the Chlorinator Output ...................................................
Start/Stop Superchlorination................................................
Program a Timeclock............................................................
Program a Countdown Timer...............................................
Enter/Exit Service Mode.......................................................
22
22
22
22
23
23
23
24
Chlorinator Operation/
Water Chemistry
Saturation Index.....................................................................
Salt Level................................................................................
Type of Salt............................................................................
How to Add or Remove Salt.................................................
25
26
26
26
System Maintenance
Servicing and Cleaning the Turbo Cell................................ 29
Winterizing.............................................................................. 29
Spring Startup........................................................................ 29
Troubleshooting &
Diagnostic Information
Service Mode .......................................................................
Check System Indicator........................................................
Diagnostic Menu...................................................................
Chlorinator Diagnostics........................................................
Instant Salt..............................................................................
Flow Switch............................................................................
Cell, Water, Air, Solar Temperature......................................
Software Revision.................................................................
Warranty
Aqua Logic Warranty............................................................. 36
30
31
32
32
32
32
33
33
LIMITED WARRANTY Goldline warrants its Aqua Rite, Aqua Rite Pro, Aqua Trol, Aqua Logic and Pro Logic products
(products with Goldline part numbers starting with AQ-RITE-, AQ-RT-PRO, AQ-TROL-, AQ-LOGIC-, AQL-P-, AQL-PS-,
AQL-CL-, PL-P-, PL-PS-, and HPC-2) to be free from defects in material or workmanship, under normal use and service:
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always
be followed, including the following:
•
•
•
•
•
READ AND FOLLOW ALL INSTRUCTIONS
!
WARNING: Disconnect all AC power during installation.
!
WARNING: Water in excess of 100 degrees Fahrenheit may be
hazardous to your health.
!
WARNING: To reduce the risk of injury, do not permit children to
use this product unless they are closely supervised at all times.
A green colored terminal marked “Earth Ground” is located inside the wiring
compartment. To reduce the risk of electric shock, this terminal must be
connected to the grounding means provided in the electric supply service
panel with a continuous copper wire equivalent in size to the circuit
conductors supplying the equipment.
•
One bonding lug for US models (two for Canadian models) is provided on the
external surface. To reduce the risk of electric shock, connect the local
common bonding grid in the area of the swimming pool, spa, or hot tub to
these terminals with an insulated or bare copper conductor not smaller than 8
AWG US / 6 AWG Canada.
•
All field installed metal components such as rails, ladders, drains, or other
similar hardware within 3 meters of the pool, spa or hot tub shall be bonded
to the equipment grounding bus with copper conductors not smaller than
8 AWG US / 6 AWG Canada.
•
SAVE THESE INSTRUCTIONS
For three years from the date of the initial system installation on private, residential swimming pools within the USA or Canada
and one year from the date of initial system installation on commercial installations, installations outside of the USA or Canada
and for any replacement parts or accessory products, provided they are installed in accordance with the Goldline installation
instructions and specifications provided with the product. If written proof of the date of the initial system installation is not
provided to Goldline, the manufacturing datecode on the Aqua Rite, Aqua Rite Pro, Aqua Trol, Aqua Logic and Pro Logic
electronics unit will be the sole determinant of the date of the initial system installation.
For residential installations in USA or Canada: If a product is defective in workmanship or materials and is removed and returned
freight prepaid within three (3) years after the date of the initial system installation, Goldline will, at its option, either repair or
replace the defective product and return it freight prepaid.
For commercial installations, installations outside the USA and Canada, and accessory products and replacement parts: If a
product is defective in workmanship or materials and is removed and returned freight prepaid within one (1) year after the date
of the initial system installation, Goldline will, at its option, either repair or replace the defective product and return it freight
prepaid.
Contact any Goldline dealer or contact Goldline at 61 Whitecap Drive, North Kingstown, RI 02852 for warranty service. The
costs incurred in removal and/or reinstallation of the product are NOT covered under this warranty. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
WARRANTY EXCLUSIONS:
1.
Material supplied or workmanship performed by others in process of installation.
2.
Damage resulting from improper installation including installation on pools larger than the product rating.
3.
Problems resulting from failure to operate the product(s) in accordance with the recommended instructions contained
in product’s owners manual(s).
4.
Problems resulting from failure to maintain pool water chemistry in accordance with the recommendations in the
owners manual(s).
5.
Problems resulting from tampering, accident, abuse, negligence, unauthorized repairs or alternations, fire, flood,
lightning, freezing, external water, degradation of natural stone used in or immediately adjacent to a pool or spa, war
or acts of God.
DISCLAIMER. THE EXPRESS LIMITED WARRANTY ABOVE CONSTITUTES THE ENTIRE WARRANTY OF
GOLDLINE WITH RESPECT TO ITS POOL AUTOMATION AND CHLORINATION PRODUCTS AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. IN NO EVENT SHALL GOLDLINE
BE RESPONSIBLE FOR ANY CONSEQUENTIAL, SPECIAL OR INCIDENTAL DAMAGES OF ANY NATURE
WHATSOEVER, INCLUDING, BUT NOT LIMITED TO, PERSONAL INJURY, PROPERTY DAMAGE, DAMAGE TO
OR LOSS OF EQUIPMENT, LOST PROFITS OR REVENUE, COSTS OF RENTING REPLACEMENTS, AND OTHER
ADDITIONAL EXPENSES, EVEN IF THE SELLER HAD BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OF LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
NO WHOLESALER, AGENT, DEALER, CONTRACTOR OR OTHER PERSON IS AUTHORIZED TO GIVE ANY
WARRANTY ON BEHALF OF GOLDLINE.
THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN ALTERED IN ANY WAY AFTER LEAVING THE FACTORY.
36
TEST
IDEAL RANGE
ADJUSTMENT REQUIRED
Free Chlorine
1.0 - 3.0 ppm
Turn output dial up to increase,
down to decrease -OR- increase
or decrease pump filtration time.
pH
7.2 - 7.6
Alkalinity
80 - 120 ppm
Salt
Aqua
Logic
Automation and Chlorination
Too high - add muriatic acid
Too low - add soda ash.
Add baking soda to increase.
Add acid as required to decrease.
2700 - 3400 ppm Add salt as required to increase.
Stabilizer
60 - 80 ppm
Add cyanuric acid to increase.
Calcium
200 - 400 ppm
Add calcium to increase.
Drain and add water to decrease.
Electrolytic Cell inspect & clean
Refer to section in manual.
(actuator, cell & remote display not included - order separately)
Operation Manual
for model
AQL-P-4
G
LDLINE
G
C ON TROLS
North Kingstown, RI 02852 USA
092032K
Copyright © 2008 Goldine Controls
LDLINE
C ON TROLS
www.goldlinecontrols.com
888-921-7665
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement