ADLINK Technology cPCI-6860A Series User`s manual

ADLINK Technology cPCI-6860A Series User`s manual
cPCIS-6400U/6400XSeries
4U Height Subsystem for
6U cPCI and Components
User’s Manual
Manual Rev.
2.01
Revision Date:
December 21, 2006
Part No:
50-15044-2000
Advance Technologies; Automate the World.
Copyright 2005 ADLINK TECHNOLOGY INC.
All Rights Reserved.
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Trademarks
Product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks
of their respective companies.
Getting Service from ADLINK
Customer Satisfaction is top priority for ADLINK Technology Inc.
Please contact us should you require any service or assistance.
ADLINK TECHNOLOGY INC.
Web Site:
http://www.adlinktech.com
Sales & Service:
[email protected]
TEL:
+886-2-82265877
FAX:
+886-2-82265717
Address:
9F, No. 166, Jian Yi Road, Chungho City,
Taipei, 235 Taiwan
Please email or FAX this completed service form for prompt and
satisfactory service.
Company Information
Company/Organization
Contact Person
E-mail Address
Address
Country
TEL
FAX:
Web Site
Product Information
Product Model
Environment
OS:
M/B:
Chipset:
CPU:
BIOS:
Please give a detailed description of the problem(s):
Table of Contents
List of Figures ........................................................................ iii
1 Introduction ........................................................................ 1
1.1
1.2
1.3
1.4
1.5
Features............................................................................... 1
General ........................................................................... 1
Boards Space ................................................................. 2
CompactPCI Compliancy ................................................ 2
Enclosure ........................................................................ 2
Specifications....................................................................... 3
Mechanical Layout............................................................... 4
cPCIS-6400U Series (redundant PSU) ........................... 4
cPCIS-6400X Series (ATX PSU) .................................... 5
Compatible CPU Modules ................................................... 7
Customized Systems ........................................................... 7
2 Getting Started ................................................................... 9
2.1
2.2
2.3
2.4
2.5
2.6
Shipping Contents ............................................................... 9
CompactPCI Card Installation ............................................. 9
Rear Transition Module Installation/Removal .................... 11
Power Supply Unit Replacement
(cPCIS-6400U only)........................................ 12
Hard Drive Racks............................................................... 13
Hard Drive Installation Procedure ................................. 13
Rack Insertion And Removal ........................................ 14
Powering Up the System ................................................... 15
3 Backplanes ....................................................................... 17
3.1
3.2
cBP-6105R (32-bit/33MHz)................................................ 18
Features ....................................................................... 18
Specifications ................................................................ 18
Mechanical Drawing ..................................................... 19
Connector Pin Assignments ......................................... 20
Jumper Settings ............................................................ 33
cBP-6405R (64-bit/66MHz)................................................ 34
Features ....................................................................... 34
Specifications ................................................................ 34
Mechanical Drawing ..................................................... 35
Connector Pin Assignments ......................................... 36
Jumper Settings ............................................................ 48
Table of Contents
i
3.3
cBP-3063 CompactPCI Power Backplane......................... 49
Specifications ................................................................ 49
Mechanical Drawing ..................................................... 50
Connector Pin Assignments ......................................... 51
4 Cooling System................................................................. 55
4.1
4.2
4.3
4.4
4.5
4.6
System Alarm Board ..........................................................
Fan Alarm ..........................................................................
Fan Removal and Replacement Procedure
(cPCIS-6400U only)........................................
Air Filter Replacement
(cPCIS-6400U only)........................................
Temperature Alarm ............................................................
Fan Specifications..............................................................
56
57
57
61
63
63
5 Power Supply Unit ............................................................ 65
5.1
5.2
cPCIS-6400U: cPS-H325/AC............................................. 65
Features ........................................................................ 65
Specifications ................................................................ 65
Input Characteristics ..................................................... 66
Output Characteristics .................................................. 66
cPCIS-6400X: APS940XA ATX 400W............................... 68
Features ........................................................................ 68
Specifications ................................................................ 68
Input Characteristics ..................................................... 68
Output Characteristics .................................................. 69
Important Safety Instructions............................................... 71
Warranty Policy ..................................................................... 73
ii
Table of Contents
List of Figures
Figure 1-1:
Figure 1-2:
Figure 1-3:
Figure 1-4:
Figure 1-5:
Figure 1-6:
Figure 2-1:
Figure 2-2:
Figure 2-3:
Figure 2-4:
Figure 2-5:
Figure 2-6:
Figure 2-7:
Figure 2-8:
Figure 3-1:
Figure 3-2:
Figure 3-3:
Figure 3-4:
Figure 3-5:
Figure 3-6:
Figure 4-1:
Figure 4-2:
Figure 4-3:
Figure 4-4:
Figure 4-5:
Figure 4-6:
cPCIS-6400U Front View .......................................... 4
cPCIS-6400U Rear View ........................................... 4
cPCIS-6400X Front View........................................... 5
cPCIS-6400X Rear View ........................................... 5
cPCIS-6400 Series Top View .................................... 6
cPCIS-6400 Series Left Side View ............................ 6
Installing a 6U SBC module..................................... 10
Latching the cPCI module handles securely. .......... 11
Unlatch the PSU module handle ............................. 12
Pull outwards to remove the PSU............................ 13
Hard drive rack keylock positions ............................ 13
Remove the hard drive rack from the drive bay....... 14
cPCIS-6400U Series switches and LEDs................ 15
cPCIS-6400X Series switches and LEDs ................ 16
cBP-6105R Backplane Front View .......................... 19
cBP-6105R Backplane Rear View........................... 19
cBP-6405R Backplane Front View .......................... 35
cBP-6405R Backplane Rear View........................... 35
cBP-3063 Power Backplane Front View.................. 50
cBP-3063 Power Backplane Rear View .................. 50
System Alarm Board Mechanical Drawing .............. 56
Alarm LEDs and reset button .................................. 57
Remove the front-access intake fan module ........... 58
Remove the rear exhaust fan module (small).......... 59
Remove the rear exhaust fan module (PSU)........... 59
Disconnect the rear exhaust fan module (PSU) power cable............................................................................ 60
Figure 4-7: Remove the left-side exhaust fan module screws ... 60
Figure 4-8: Remove the left exhaust fan module and
disconnect the power cables .................................. 61
Figure 4-9: Air filter removal and replacement........................... 62
List of Figures
iii
iv
1
Introduction
The cPCIS-6400U/6400X Series subsystems are designed for 6U
cPCI boards with 80mm RTMs. The chassis is 4U in height and
standard 19” rack mount width.
The cPCIS-6400U provides 2+1 hot swappable 500W+250W
redundant power supplies with universal AC input, while the
cPCIS-6400X has a built-in 400W AC-input ATX power supply
with cooling fan. Both series have PICMG 2.1 Hot Swap compliant
32/64-bit 5-slot CompactPCI backplanes and a PICMG 2.5 H.110
CT Bus.
1.1 Features
General
X
19” rackmount, 4U height for 6U cPCI cards with 80mm rear
RTMs for I/O
X
Standard 6U CompactPCI and optional PICMG 2.5 H.110
CT bus
X
PICMG 2.1 Hot Swap compliant 32-bit/33MHz or
64-bit/66MHz 5-slot CompactPCI backplane with P3 & P5
rear I/O
X
2+1 hot swappable 500W+250W redundant power supplies
with universal AC input (cPCIS-6400U)
X
Built-in 400W AC-input ATX power supply (cPCIS-6400X)
X
Dual removable ATA-100 or SCSI 3.5” hard drive racks
(cPCIS-6400US and cPCIS-6400XS models are SCSI
equipped)
X
Front drive bay space for one slim type EIDE CD-ROM and
one slim type floppy.
X
One front-access intake fan, two (three for cPCIS-6400U)
rear-access and four side exhaust fans are used for system
cooling. Air-filter is replaceable on front-access fan module.
(Only cPCIS-6400U fans support hot swap).
Introduction
1
X
Guarded power switch and reset button
X
Voltage LEDs allow convenient monitoring: +12V, -12V,
+5V, +3.3V
X
Suitable for both rackmount and benchtop applications
X
Built-in alarm module to monitor chassis temperature, fan
status.
X
Comprehensive EMC shielding: EMC gaskets are installed
on top and bottom edges of both front and rear panel apertures
Boards Space
X
Board space supports standard 6U height and 6-slot width
X
One 8HP system slot accommodates single or dual-slot
system boards.
X
Both front and rear access possible
CompactPCI Compliancy
X
PICMG 2.0 R3.0 CompactPCI Core Specification
X
PICMG 2.1 R2.0 CompactPCI Hot Swap
X
PICMG 2.5 R1.0 CompactPCI Computer Telephony
X
PICMG 2.9 R1.0 CompactPCI System Management
X
PICMG 2.11 R1.0 CompactPCI Power Interface
(cPCIS-6400U only)
Enclosure
2
X
EIA RS-310C 19” 4U high rackmount enclosure
X
Coated metal plate outer covering
Introduction
1.2 Specifications
CompactPCI Standards PICMG 2.0; 2.1; 2.5; 2.9; 2.11
Form Factor
6U cPCI with 80 mm depth rear I/O
Enclosure
EIA RS-310C 19" 9U high rack-mount enclosure
Coated metal plate outer covering
Guarded power switch and reset button
Basic Alarm Module
(model dependent)
Monitors inner chassis temperature & fan status (model
dependent)
Abnormal status will generate alarm and LED warning
Audible alarm reset
LED indicators display voltage status on 5V, 3.3V, 12V
and -12V
Remote Chassis
Monitoring Module
(model dependent)
Basic Alarm functions plus: Monitors boards via the
Intelligent Platform Management Interface (IPMI)
Monitors backplane voltages and status for up to eight
power supplies
Remote login and management via LAN or modem
Remote reset control for computing blades
Web-based GUI for both remote and stand-alone
applications
Cooling System
Front access fan tray for intake
Rear and side access fan modules for exhaust
(see Chapter 4 Cooling for details)
Drive Bay
Two 5.25” drive bays
Power Supply
Supports up to 4 in-rack 3U cPCI 8HP power modules
Supports current sharing on 5V, 3.3V and 12V
PICMG 2.11 47-pin power interface
Available power module: cPS-H325/AC (250W N+1
redundant each)
Dimension
483.2 x 399 x 299.1 (mm, WxHxD, w/o handles)
Operating Temperature
0 to 50°C (depending on system configuration)
Storage Temperature
-20 to 80°C
Humidity
5% to 95%, non-condensing
Shock
15G peak-to-peak, 11ms duration, non-operation
Vibration
Non-operation:1.88Grms, 5-500Hz, each axis
Operation: 0.5Grms, 5-500Hz, each axis
Safety, Certification,
EBS
CE, FCC class A, Designed for NEBS Level 3
Introduction
3
1.3 Mechanical Layout
cPCIS-6400U Series (redundant PSU)
Figure 1-1: cPCIS-6400U Front View
Figure 1-2: cPCIS-6400U Rear View
4
Introduction
cPCIS-6400X Series (ATX PSU)
Figure 1-3: cPCIS-6400X Front View
Figure 1-4: cPCIS-6400X Rear View
Introduction
5
cPCIS-6400 Series External Dimensions (mm)
Figure 1-5: cPCIS-6400 Series Top View
Figure 1-6: cPCIS-6400 Series Left Side View
6
Introduction
1.4 Compatible CPU Modules
For complete systems, users must order CPU modules in addition
to the sub-system. The following table lists which ADLINK CompactPCI CPU modules are compatible with the cPCIS-6400 Series
models.
CPU Module
32-bit/33MHz
64-bit/66MHz
cPCI-6860A
—
yes
cPCI-6840
—
yes
cPCI-6830
—
yes
cPCI-6820
—
yes
cPCI-6810
—
yes
cPCI-6780
yes
yes
cPCI-6765/6765A
yes
yes
cPCI-6760D
yes
—
Note:
For systems requiring SCSI hard drive support, be sure
that the appropriate CPU module and Rear Transition
Module are ordered.
1.5 Customized Systems
Subsystems can be customized to meet the specific needs of your
application. To customize a sub-system please contact an
ADLINK dealer, or visit the Where to Buy page of our website for
more information: http://www.adlinktech.com.
Introduction
7
8
Introduction
2
Getting Started
This chapter describes the unpacking procedure of the sub-system and installation procedures for CompactPCI boards and
power supply units (PSUs), and hard drive rack operation procedures.
2.1 Shipping Contents
Check the shipping carton for any damage. If the shipping carton
and contents are damaged, please notify the dealer for a replacement. Retain the shipping carton and packing material for inspection by the dealer. Obtain authorization before returning any
product to ADLINK.
Check that the following items are included in the package. If there
are any missing items, please contact your dealer:
X
One cPCIS-6400U or cPCIS-6400X sub-system
X
Accessory Package: includes power cords for 110V and
220V wall sockets, replacement air filter, ergonomic rackmount handles, and pouch containing screws, zip ties, etc.
X
This User’s Manual
2.2 CompactPCI Card Installation
CompactPCI connectors are rigid, and therefore require careful
handling when inserted and removed. Improper manipulation of
the cards will result in damage to the backplane.
System slots usually have some obvious indicators, something
like red card guide rail, triangle mark enclosing the slot number on
the backplane. The system card only can be installed in the system slot, and do not insert system card into any other slot, or insert
any peripheral card into system slot.
The handles on CompactPCI card helps users to install or remove
easily and safety. Please follow the procedures below to install a
CompactPCI module into a chassis:
Getting Started
9
The handles on CompactPCI cards and PSUs ensure simple and
safe installation and removal. Please follow the procedures below
to install a CompactPCI module into a chassis:
1. Place the sub-system on a level surface or rackmount it.
Remove the blanking plates where required by undoing
the retaining screws at each end. Retain the blanking
plates for possible future use. The system should not be
put into use without blanking plates for all empty slots,
otherwise the EMC and cooling performance will be
compromised.
2. Hold the SBC module or peripheral card horizontally.
Make sure that the handles are unlatched (i.e. that they
are spread outwards). If necessary, unlatch the handle
by pressing on the release button with your thumb.
Figure 2-1: Installing a 6U SBC module
3. Carefully insert the module into the desired slot by sliding the edges of the board into the appropriate card
guide rail. Take care to ensure correct alignment of the
card with the chassis during insertion to prevent damage
to the card and/or backplane.
10
Getting Started
4. Continue inserting the card until the handles engage with
the chassis.
5. Pull inwards on the handles for final insertion. Ensure
that the red buttons on the handles fully latch into position as unless this is done the card is not correctly
inserted. Fasten the retaining screws at each end of the
card (2 for single slot cards, 4 for double slot cards)
Figure 2-2: Latching the cPCI module handles securely.
6. To remove the module, undo the retaining screws, press
the red release buttons, and reverse steps 1 through 5
above.
2.3 Rear Transition Module Installation/Removal
The installation and removal procedures for a Rear Transition
Module (RTM) are the same as those for CompactPCI boards.
Because they are shorter than front boards, pay careful attention
when inserting or removing RTMs. Only models with an “R” at the
end of the model number support RTMs.
Note: We strongly recommended the use of RTMs with AB type
connectors to prevent the damage to the backplane during
RTM installation.
Getting Started
11
2.4 Power Supply Unit Replacement
(cPCIS-6400U only)
The cPCIS-6400U series subsystems come with cPS-H325 PSUs
pre-installed. The removal and installation procedures for PSUs
are the same as for CompactPCI cards, except there is only one
handle. To replace a PSU module, refer to the figures and instructions below.
1. To remove the PSU module, undo the retaining screws
and unlatch the handle by pressing on the release button
with your thumb.
Figure 2-3: Unlatch the PSU module handle
12
Getting Started
2. Pull outwards to remove the PSU.
Figure 2-4: Pull outwards to remove the PSU
3. Insert the new PSU module, push on the handle until it
latches into position, and replace the retaining screws.
2.5 Hard Drive Racks
The cPCI-6400U and cPCIS-6400X subsystems have two hard
drive racks for 3.5” hard drives. The racks are protected by keylocks to prevent accidental or unauthorized removal. The following
sections describe initial hard drive installation and rack insertion
and removal.
Hard Drive Installation Procedure
1. To unlock the rack., insert the key into to the keylock and
rotate it clockwise so that the key is in the 3 o’clock
position.
Figure 2-5: Hard drive rack keylock positions
Getting Started
13
2. Lift the rack handle outwards and pull the hard drive rack
out of the drive bay.
Figure 2-6: Remove the hard drive rack from the drive bay
3. Insert the hard drive into the rack and secure with
screws as per standard hard drive installation procedure.
4. For IDE hard drives, attach the ribbon cable and power
cord to the back of the drive (skip for SCSI drives).
5. Insert the hard drive rack into the drive bay and push
down on the handle until the rack is firmly secured in
place.
6. To lock the rack, insert the key into to the keylock and
rotate it counter-clockwise so that the key is in the 12
o’clock position.
Rack Insertion And Removal
Follow the instructions for Hard Drive Installation above, skipping
steps 3 and 4.
14
Getting Started
2.6 Powering Up the System
Connect the supplied power cord to the socket on the back of the
chassis. All supplied PSUs are full range 90-240VAC and do not
require input voltage setting. Insert the desired boards into the
appropriate card slots as described in Sections 2.2 and 2.3.
The cPCIS-6400U/X subsystems feature a guarded power switch
and reset button that provide ATX power control capability. Use
the tool provided in the Accessory Packet or a suitably shaped
object (such as a pen) to actuate the power switch and reset
button. Voltage LEDs allow convenient monitoring of the power
supply.
Refer to the diagrams below for LED and switch locations.
cPCIS-6400U Series (redundant PSU)
Figure 2-7: cPCIS-6400U Series switches and LEDs
Getting Started
15
cPCIS-6400X Series (ATX PSU)
Figure 2-8: cPCIS-6400X Series switches and LEDs
16
Getting Started
3
Backplanes
In this chapter, we will describe the backplanes for the cPCIS6400U/6400X Series. The following table outlines the backplanes
that correspond to each model.
Model
Type
Backplane
cPCIS-6400U/32
cPCIS-6400X/32
32-bit/33MHz
cBP-6105R
cPCIS-6400U/64
cPCIS-6400X/64
64-bit/66MHz
cBP-6405R
The cPCIS-6400U Series models use the cBP-3063 CompactPCI
Power Backplane.
Backplanes
17
3.1 cBP-6105R (32-bit/33MHz)
The backplane for the cPCIS-6400 Series 6U 32-bit, 5-slot chassis
is the cBP-6105R, a 6U 5-slot H.110 32-bit CompactPCI backplane with rear I/O.
Features
X
Standard CompactPCI 3U height for 6U cPCI cards
X
Supports 80mm rear I/O for each slot
X
Suitable for one single/dual-slot system module and four
expansion cards
X
Supports PICMG 2.5 H.110 CT Bus
X
PICMG 2.1 Hot Swap compliant 32-bit 5-slot CompactPCI
backplane with P3 & P5 rear I/O
Specifications
X
18
CompactPCI Compliancy
Z
PICMG 2.0 CompactPCI core specification R3.0
Z
PICMG 2.1 CompactPCI hot swap R2.0
Z
PICMG 2.5 CompactPCI Computer Telephony R1.0
X
Dimension: 262.05 x 120.9 (mm, W x H)
X
PCI bus clock: 32-bit/33MHz
X
System slot rear I/O: P3, P4 and P5 rear I/O with AB type
shroud
X
Peripheral slots: four
X
H.110 bus: Compliant with PICMG 2.5, for all peripheral
slots
X
V (I/O): 3.3V or 5V selectable, default 5V
X
Power Connectors: ATX connector x1, DC screw terminals
X
System slot legacy I/O: FDD, IDE1, and IDE2 (pin compatible with cPCI-6760Dand cPCI-6780 only)
X
Other connectors: INH#, Reset, PWR_FAL#, Voltage LEDs,
H.110 Power Pairs (VRG, Vbat)
Backplanes
Mechanical Drawing
Figure 3-1: cBP-6105R Backplane Front View
Figure 3-2: cBP-6105R Backplane Rear View
Backplanes
19
Connector Pin Assignments
ATX Power Connector [CN1]
Pin
Signal
Pin
Signal
1
2
+3.3V
11
+3.3V
+3.3V
12
-12V
3
GND
13
GND
4
+5V
14
PS_ON_L
5
GND
15
GND
6
+5V
16
GND
7
GND
17
GND
8
PWRGOOD
18
-5V
9
STB5V
19
+5V
10
+12V
20
+5V
Power LED Connector [JP2]
1
2
7
8
Pin
Signal
Pin
Signal
1
+12V
2
GND
3
-12V
4
GND
5
+3.3V
6
GND
7
+5V
8
GND
SM Bus Connector [JP3]
1
20
Pin
Signal
1
CLK
2
GND
3
DATA
4
V(I/O)
5
ALERT#
Backplanes
H.110 DC Power Connector [CN6]
1
Pin
Signal
1
-SEL Vbat
2
SEL VbatRtn
3
VRG
4
VRGRtn
5
-Vbat
6
VbatRtn
Pin
Signal
1
PRSTA#
2
GND
Pin
Signal
1
FAL#
2
GND
Pin
Signal
1
INH#
2
GND
RST# Connector [J1]
FAL# Connector [J2]
INH# Connector [J3]
Backplanes
21
System Slot: [1–P1]
Pin
Z
A
B
C
D
25
24
GND
+5V
REQ64#
ENUM#
+3.3V
GND
AD[1]
+5V
V(I/O)
AD[0]
23
GND
+3.3V
AD[4]
AD[3]
+5V
AD[2]
GND
22
GND
AD[7]
GND
+3.3V
AD[6]
AD[5]
GND
21
GND
+3.3V
AD[9]
AD[8]
M66EN C/BE[0]# GND
20
GND
AD[12]
GND
V(I/O)
AD[11]
19
GND
+3.3V
AD[15]
AD[14]
GND
18
GND
SERR#
GND
+3.3V
PAR
17
GND
+3.3V
IPMB_SCL
IPMB_SDA
GND
PERR#
GND
16
GND
DEVSEL#
GND
V(I/O)
STOP#
LOCK#
GND
15
GND
+3.3V
FRAME#
IRDY#
BDSEL
TRDY#
GND
11
GND
AD[18]
AD[17]
AD[16]
GND
10
GND
AD[21]
GND
+3.3V
AD[20]
AD[19]
GND
9
GND
C/BE[3]#
GND
AD[23]
GND
AD[22]
GND
8
GND
AD[26]
GND
V(I/O)
AD[25]
AD[24]
GND
7
GND
AD[30]
AD[29]
AD[28]
GND
AD[27]
GND
6
GND
REQ#
GND
+3.3V
CLK
AD[31]
GND
5
GND
Reserved
Reserved
PCIRST#
GND
GNT#
GND
4
GND
IPMB_PWR
HEALTHY#
V(I/O)
INTP
INTS
GND
3
GND
INTA#
INTB#
INTC#
+5V
INTD#
GND
2
GND
TCK
+5V
TMS
TDO
TDI
GND
1
GND
+5V
-12V
TRST#
+12V
+5V
GND
12-14
22
E
F
+5V
GND
ACK64# GND
AD[10]
GND
AD[13]
GND
C/BE[1]# GND
Keying Area
C/BE[2]# GND
Backplanes
System Slot: [1–P2]
Pin
Z
A
B
C
D
E
F
22
GND
GA4
GA3
GA2
GA1
GA0
GND
21
GND
CLK6
GND
Reserved
Reserved
Reserved
GND
20
GND
CLK5
GND
Reserved
GND
Reserved
GND
19
GND
GND
GND
SMDATA
SMCLK
ALERT#
GND
18
GND
Reserved
Reserved
Reserved
GND
Reserved
GND
17
GND
Reserved
GND
PRST#
REQ6#
GNT6#
GND
16
GND
Reserved
Reserved
DEG#
GND
Reserved
GND
15
GND
Reserved
GND
FAL#
REQ5#
GNT5#
GND
14
GND
Reserved
Reserved
Reserved
GND
Reserved
GND
13
GND
Reserved
GND
V(I/O)
Reserved
Reserved
GND
12
GND
Reserved
Reserved
Reserved
GND
Reserved
GND
11
GND
Reserved
GND
V(I/O)
Reserved
Reserved
GND
10
GND
Reserved
Reserved
Reserved
GND
Reserved
GND
9
GND
Reserved
GND
V(I/O)
Reserved
Reserved
GND
8
GND
Reserved
Reserved
Reserved
GND
Reserved
GND
7
GND
Reserved
GND
V(I/O)
Reserved
Reserved
GND
6
GND
Reserved
Reserved
Reserved
GND
Reserved
GND
5
GND
Reserved
GND
V(I/O)
Reserved
Reserved
GND
4
GND
V(I/O)
Reserved
Reserved
GND
Reserved
GND
3
GND
CLK4
GND
GNT3#
REQ4#
GNT4#
GND
2
GND
CLK2
CLK3
SYSEN#
GNT2#
REQ3#
GND
1
GND
CLK1
GND
REQ1#
GNT1#
REQ2#
GND
Backplanes
23
System Slot: [1–P3]
Pin
Z
A
B
C
D
E
F
19
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
18
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
17
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
16
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
15
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
14
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
13
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
12
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
11
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
10
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
9
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
8
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
7
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
6
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
5
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
4
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
3
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
2
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
1
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
24
Backplanes
System Slot: [1–P4]
Pin
Z
A
B
C
D
E
F
25
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
24
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
23
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
22
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
21
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
20
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
19
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
18
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
17
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
16
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
15
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
11
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
10
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
9
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
8
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
7
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
6
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
5
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
4
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
3
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
2
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
1
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
12-14
Keying Area
Backplanes
25
System Slot: [1–P5]
Pin
Z
A
B
C
D
E
F
22
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
21
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
20
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
19
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
18
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
17
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
16
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
15
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
14
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
13
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
12
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
11
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
10
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
9
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
8
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
7
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
6
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
5
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
4
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
3
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
2
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
1
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
26
Backplanes
Peripheral Slot: [2–P1] - [5–P1]
Pin
Z
A
B
C
D
25
24
GND
+5V
REQ64#
ENUM#
+3.3V
GND
AD[1]
+5V
V(I/O)
AD[0]
23
GND
+3.3V
AD[4]
AD[3]
+5V
AD[2]
GND
22
GND
AD[7]
GND
+3.3V
AD[6]
AD[5]
GND
21
GND
+3.3V
AD[9]
AD[8]
M66EN C/BE[0]# GND
20
GND
AD[12]
GND
V(I/O)
AD[11]
19
GND
+3.3V
AD[15]
AD[14]
GND
18
GND
SERR#
GND
+3.3V
PAR
17
GND
+3.3V
IPMB_SCL
IPMB_SDA
GND
PERR#
16
GND
DEVSEL#
GND
V(I/O)
STOP#
LOCK#
GND
15
GND
+3.3V
FRAME#
IRDY#
BDSEL
TRDY#
GND
11
GND
AD[18]
AD[17]
AD[16]
GND
10
GND
AD[21]
GND
+3.3V
AD[20]
AD[19]
GND
9
GND
C/BE[3]#
IDSEL
AD[23]
GND
AD[22]
GND
8
GND
AD[26]
GND
V(I/O)
AD[25]
AD[24]
GND
7
GND
AD[30]
AD[29]
AD[28]
GND
AD[27]
GND
6
GND
REQ#
GND
+3.3V
CLK
AD[31]
GND
5
GND
Reserved
Reserved
PCIRST#
GND
GNT#
GND
4
GND
IPMB_PWR
HEALTHY#
V(I/O)
INTP
INTS
GND
3
GND
INTA#
INTB#
INTC#
+5V
INTD#
GND
2
GND
TCK
+5V
TMS
TDO
TDI
GND
1
GND
+5V
-12V
TRST#
+12V
+5V
GND
12-14
E
F
+5V
GND
ACK64# GND
AD[10]
GND
AD[13]
GND
C/BE[1]# GND
GND
Keying Area
Backplanes
C/BE[2]# GND
27
Peripheral Slot: [2–P2] - [5–P2]
Pin
Z
A
B
C
D
E
F
22
GND
GA4
GA3
GA2
21
GND
Reserved
GND
Reserved
GA1
GA0
GND
Reserved
Reserved
20
GND
Reserved
GND
Reserved
GND
GND
Reserved
GND
19
GND
GND
GND
18
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
Reserved
GND
Reserved
17
GND
Reserved
GND
GND
Reserved
Reserved
Reserved
GND
16
GND
Reserved
Reserved
Reserved
GND
Reserved
GND
15
GND
Reserved
GND
Reserved
Reserved
Reserved
GND
14
GND
AD[35]
AD[34]
AD[33]
GND
AD[32]
GND
13
GND
AD[38]
GND
V(I/O)
AD[37]
AD[36]
GND
12
GND
AD[42]
AD[41]
AD[40]
GND
AD[39]
GND
11
GND
AD[45]
GND
V(I/O)
AD[44]
AD[43]
GND
10
GND
AD[49]
AD[48]
AD[47]
GND
AD[46]
GND
9
GND
AD[52]
GND
V(I/O)
AD[51]
AD[50]
GND
8
GND
AD[56]
AD[55]
AD[54]
GND
AD[53]
GND
7
GND
AD[59]
GND
V(I/O)
AD[58]
AD[57]
GND
6
GND
AD[63]
AD[62]
AD[61]
GND
AD[60]
GND
5
GND
C/BE[5]#
GND
V(I/O)
C/BE[4]#
PAR64
GND
4
GND
V(I/O)
Reserved
C/BE[7]#
GND
C/BE[6]#
GND
3
GND
Reserved
GND
Reserved
Reserved
Reserved
GND
2
GND
Reserved
Reserved
SYSEN#
Reserved
Reserved
GND
1
GND
Reserved
GND
Reserved
Reserved
Reserved
GND
28
Backplanes
Peripheral Slot: [2–P3] - [5–P3]
Pin
Z
A
B
C
D
E
F
19
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
18
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
17
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
16
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
15
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
14
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
13
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
12
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
11
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
10
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
9
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
8
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
7
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
6
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
5
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
4
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
3
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
2
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
1
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
Backplanes
29
Peripheral Slot: [2–P4] - [5–P4]
Pin
Z
A
B
C
D
E
F
25
GND
SGA4
SGA3
SGA2
SGA1
SGA0
GND
24
GND
GA4
GA3
GA2
GA1
GA0
GND
23
GND
+12V
Reserved
CT_EN#
-12V
CT_MC
GND
22
GND
PFS0#
21
GND -SELVbat
PFS1#
20
GND
No Pin
No Pin
19
GND
No Pin
No Pin
No Pin
No Pin
No Pin
GND
18
GND
VRG
No Pin
No Pin
No Pin
VRG Rtn
GND
17
GND
No Pin
No Pin
No Pin
No Pin
No Pin
GND
16
GND
No Pin
No Pin
No Pin
No Pin
No Pin
GND
15
GND
-Vbat
No Pin
No Pin
No Pin
-Vbat Rtn
GND
11
GND
CT_D29
CT_D30
CT_D31
V(I/O)
CT_FRAME_A GND
10
GND
CT_D27
+3.3V
CT_D28
+5V
CT_FRAME_B GND
9
GND
CT_D24
CT_D25
CT_D26
GND
RF_COMP
GND
8
GND
CT_D21
CT_D22
CT_D23
+5V
CT_C8_A
GND
7
GND
CT_D19
+5V
CT_D20
GND
CT_C8_B
GND
6
GND
CT_D16
CT_D17
CT_D18
GND
CT_NETREF_1 GND
5
GND
CT_D13
CT_D14
CT_D16
+3.3V
CT_NETREF_2 GND
4
GND
CT_D11
+5V
CT_D12
+3.3V
SCLK
GND
3
GND
CT_D8
CT_D9
CT_D10
GND
SCLK-D
GND
2
GND
CT_D4
CT_D5
CT_D6
CT_D7
GND
GND
1
GND
CT_D0
+3.3V
CT_D1
CT_D2
CT_D3
GND
CT_RESET Reserved Reserved
12-14
30
Reserved Reserved
No Pin
No Pin
Reserved
GND
-SELVbat Rtn
GND
No Pin
GND
Keying Area
Backplanes
Peripheral Slot: [2–P5] - [5–P5]
Pin
Z
A
B
C
D
E
F
22
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
21
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
20
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
19
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
18
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
17
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
16
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
15
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
14
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
13
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
12
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
11
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
10
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
9
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
8
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
7
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
6
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
5
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
4
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
3
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
2
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
1
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
Backplanes
31
IDE Add-on Card: [0–P3]
Pin
Z
A
B
C
D
E
F
25
GND
+12V
GND
+5V
NC
GND
GND
24
GND
+12V
GND
+5V
NC
GND
GND
23
GND
+12V
GND
+5V
NC
GND
GND
22
GND PPWRGD
PIRQ
GND
21
GND
PDACT#
AP3B18
PCS3#
PCS1#
PPDIAG GND
20
GND
PDD15
PDD14
PDD13
PDD12
AP3E17
19
GND
PDD11
PDD10
PDD9
PDD8
DDAK0# GND
18
GND
PDA0
PDA1
NC
PDA2
DDRQ0
17
GND
PDD7
PDD6
PDD5
PDD4
DIOW0# GND
16
GND
PDD3
PDD2
PDD1
PDD0
DIOR0#
15
GND
DR0#
MSEN0
MTR0#
11
GND
DR1#
DSKCHG#
MTR1#
DENSL
10
GND
WP#
HDSEL#
DIR#
TRK0#
9
GND WGATE#
AP3B9
AP3C9
AP3D9
AP3E9
GND
8
GND
AP3A8
AP3B8
NC
AP3D8
AP3E8
GND
7
GND
AP3A7
AP3B7
AP3C7
AP3D7
AP3E7
GND
6
GND
AP3A6
AP3B6
AP3C6
AP3D6
AP3E6
GND
5
GND
AP3A5
AP3B5
AP3C5
AP3D5
AP3E5
GND
4
GND
AP3A4
AP3B4
NC
AP3D4
AP3E4
GND
3
GND
AP3A3
AP3B3
AP3C3
AP3D3
AP3E3
GND
2
GND
AP3A2
AP3B2
AP3C2
AP3D2
AP3E2
GND
1
GND
AP3A1
AP3B1
AP3C1
AP3D1
AP3E1
GND
PDCS16# PIORDY AP3D19
12-14
32
GND
GND
GND
INDEX# WDATA# GND
Keying Area
RDATA# GND
STEP#
GND
Backplanes
Jumper Settings
Shelf Enumeration Bus Signals [JP1] - (default: 1-2 shorted)
Column 1
Column 2
Column 3
NC
SGA0
GND
NC
SGA1
GND
NC
SGA2
GND
NC
SGA3
GND
NC
SGA4
GND
V(I/O) Setting Jumper [J4 - J6] - (default: J4-J5 shorted)
Backplanes
Pin
Signal
J4
+5V
J5
V(I/O)
J6
+3.3V
33
3.2 cBP-6405R (64-bit/66MHz)
The backplane for the cPCIS-6400 Series 6U 64-bit, 5-slot chassis
is the cBP-6405R, a 6U 64-bit, 5-slot, H.110 CompactPCI backplane with rear I/O.
Features
X
Standard CompactPCI 3U height for 6U cPCI cards
X
Supports 80mm rear I/O for each slot
X
Suitable for one single/dual-slot system module and four
expansion cards
X
Supports PICMG 2.5 H.110 CT Bus
X
PICMG 2.1 Hot Swap compliant 64-bit 5-slot CompactPCI
backplane with P3 & P5 rear I/O
Specifications
X
34
CompactPCI Compliancy
Z
PICMG 2.0 CompactPCI core specification R3.0
Z
PICMG 2.1 CompactPCI hot swap R2.0
Z
PICMG 2.5 CompactPCI Computer Telephony R1.0
X
Dimension: 262.05 x 120.9 (mm, W x H)
X
PCI bus clock: up to 64-bit/66MHz
X
System slot rear I/O: P3, P4 and P5 rear I/O with AB type
shroud
X
Peripheral slots: four
X
H.110 bus: Compliant with PICMG 2.5, for all peripheral
slots
X
V (I/O): 3.3V or 5V selectable, default 5V
X
Power Connectors: ATX connector x1, DC screw terminals
X
System slot legacy I/O: FDD, IDE1, and IDE2 (pin compatible with cPCI-6760Dand cPCI-6780 only)
X
Other connectors: INH#, Reset, PWR_FAL#, Voltage LEDs,
H.110 Power Pairs (VRG, Vbat)
Backplanes
Mechanical Drawing
Figure 3-3: cBP-6405R Backplane Front View
Figure 3-4: cBP-6405R Backplane Rear View
Backplanes
35
Connector Pin Assignments
ATX Power Connector [CN1, CN3]
Pin
Signal
Pin
Signal
1
2
+3.3V
11
+3.3V
+3.3V
12
-12V
3
GND
13
GND
4
+5V
14
PS_ON_L
5
GND
15
GND
6
+5V
16
GND
7
GND
17
GND
8
PWRGOOD
18
-5V
9
STB5V
19
+5V
10
+12V
20
+5V
Power LED Connector [JP2]
1
2
7
8
Pin
Signal
Pin
Signal
1
+12V
2
GND
3
-12V
4
GND
5
+3.3V
6
GND
7
+5V
8
GND
SM Bus Connector [JP3]
1
36
Pin
Signal
1
CLK
2
GND
3
DATA
4
V(I/O)
5
ALERT#
Backplanes
H.110 DC Power Connector [CN6]
1
Pin
Signal
1
-SEL Vbat
2
SEL VbatRtn
3
VRG
4
VRGRtn
5
-Vbat
6
VbatRtn
Pin
Signal
1
PRSTA#
2
GND
Pin
Signal
1
FAL#
2
GND
Pin
Signal
1
INH#
2
GND
RST# Connector [J1]
FAL# Connector [J2]
INH# Connector [J3]
Backplanes
37
System Slot: [1–P1]
Pin
Z
A
B
C
D
25
24
GND
+5V
REQ64#
ENUM#
+3.3V
GND
AD[1]
+5V
V(I/O)
AD[0]
23
GND
+3.3V
AD[4]
AD[3]
+5V
AD[2]
GND
22
GND
AD[7]
GND
+3.3V
AD[6]
AD[5]
GND
21
GND
+3.3V
AD[9]
AD[8]
M66EN C/BE[0]# GND
20
GND
AD[12]
GND
V(I/O)
AD[11]
19
GND
+3.3V
AD[15]
AD[14]
GND
18
GND
SERR#
GND
+3.3V
PAR
17
GND
+3.3V
IPMB_SCL
IPMB_SDA
GND
PERR#
GND
16
GND
DEVSEL#
GND
V(I/O)
STOP#
LOCK#
GND
15
GND
+3.3V
FRAME#
IRDY#
BDSEL
TRDY#
GND
11
GND
AD[18]
AD[17]
AD[16]
GND
10
GND
AD[21]
GND
+3.3V
AD[20]
AD[19]
GND
9
GND
C/BE[3]#
GND
AD[23]
GND
AD[22]
GND
8
GND
AD[26]
GND
V(I/O)
AD[25]
AD[24]
GND
7
GND
AD[30]
AD[29]
AD[28]
GND
AD[27]
GND
6
GND
REQ#
GND
+3.3V
CLK
AD[31]
GND
5
GND
Reserved
Reserved
PCIRST#
GND
GNT#
GND
4
GND
IPMB_PWR
HEALTHY#
V(I/O)
INTP
INTS
GND
3
GND
INTA#
INTB#
INTC#
+5V
INTD#
GND
2
GND
TCK
+5V
TMS
TDO
TDI
GND
1
GND
+5V
-12V
TRST#
+12V
+5V
GND
12-14
38
E
F
+5V
GND
ACK64# GND
AD[10]
GND
AD[13]
GND
C/BE[1]# GND
Keying Area
C/BE[2]# GND
Backplanes
System Slot: [1–P2]
Pin
Z
A
B
C
D
E
F
22
GND
GA4
GA3
GA2
GA1
GA0
GND
21
GND
CLK6
GND
Reserved
Reserved
Reserved
GND
20
GND
CLK5
GND
Reserved
GND
Reserved
GND
19
GND
GND
GND
SMDATA
SMCLK
ALERT#
GND
18
GND
Reserved
Reserved
Reserved
GND
Reserved
GND
17
GND
Reserved
GND
PRST#
REQ6#
GNT6#
GND
16
GND
Reserved
Reserved
DEG#
GND
Reserved
GND
15
GND
Reserved
GND
FAL#
REQ5#
GNT5#
GND
14
GND
AD[35]
AD[34]
AD[33]
GND
AD[32]
GND
13
GND
AD[38]
GND
V(I/O)
AD[37]
AD[36]
GND
12
GND
AD[42]
AD[41]
AD[40]
GND
AD[39]
GND
11
GND
AD[45]
GND
V(I/O)
AD[44]
AD[43]
GND
10
GND
AD[49]
AD[48]
AD[47]
GND
AD[46]
GND
9
GND
AD[52]
GND
V(I/O)
AD[51]
AD[50]
GND
8
GND
AD[56]
AD[55]
AD[54]
GND
AD[53]
GND
7
GND
AD[59]
GND
V(I/O)
AD[58]
AD[57]
GND
6
GND
AD[63]
AD[62]
AD[61]
GND
AD[60]
GND
5
GND
C/BE[5]#
GND
V(I/O)
C/BE[4]#
PAR64
GND
4
GND
V(I/O)
Reserved
C/BE[7]#
GND
C/BE[6]#
GND
3
GND
CLK4
GND
GNT3#
REQ4#
GNT4#
GND
2
GND
CLK2
CLK3
SYSEN#
GNT2#
REQ3#
GND
1
GND
CLK1
GND
REQ1#
GNT1#
REQ2#
GND
Backplanes
39
System Slot: [1–P3]
Pin
Z
A
B
C
D
E
F
19
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
18
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
17
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
16
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
15
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
14
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
13
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
12
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
11
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
10
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
9
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
8
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
7
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
6
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
5
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
4
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
3
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
2
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
1
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
40
Backplanes
System Slot: [1–P4]
Pin
Z
A
B
C
D
E
F
25
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
24
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
23
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
22
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
21
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
20
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
19
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
18
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
17
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
16
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
15
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
11
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
10
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
9
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
8
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
7
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
6
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
5
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
4
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
3
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
2
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
1
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
12-14
Keying Area
Backplanes
41
System Slot: [1–P5]
Pin
Z
A
B
C
D
E
F
22
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
21
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
20
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
19
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
18
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
17
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
16
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
15
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
14
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
13
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
12
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
11
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
10
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
9
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
8
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
7
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
6
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
5
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
4
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
3
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
2
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
1
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
42
Backplanes
Peripheral Slot: [2–P1] - [5–P1]
Pin
Z
A
B
C
D
25
24
GND
+5V
REQ64#
ENUM#
+3.3V
GND
AD[1]
+5V
V(I/O)
AD[0]
23
GND
+3.3V
AD[4]
AD[3]
+5V
AD[2]
GND
22
GND
AD[7]
GND
+3.3V
AD[6]
AD[5]
GND
21
GND
+3.3V
AD[9]
AD[8]
M66EN C/BE[0]# GND
20
GND
AD[12]
GND
V(I/O)
AD[11]
19
GND
+3.3V
AD[15]
AD[14]
GND
18
GND
SERR#
GND
+3.3V
PAR
17
GND
+3.3V
IPMB_SCL
IPMB_SDA
GND
PERR#
GND
16
GND
DEVSEL#
GND
V(I/O)
STOP#
LOCK#
GND
15
GND
+3.3V
FRAME#
IRDY#
BDSEL
TRDY#
GND
11
GND
AD[18]
AD[17]
AD[16]
GND
10
GND
AD[21]
GND
+3.3V
AD[20]
AD[19]
GND
9
GND
C/BE[3]#
IDSEL
AD[23]
GND
AD[22]
GND
8
GND
AD[26]
GND
V(I/O)
AD[25]
AD[24]
GND
7
GND
AD[30]
AD[29]
AD[28]
GND
AD[27]
GND
6
GND
REQ#
GND
+3.3V
CLK
AD[31]
GND
5
GND
Reserved
Reserved
PCIRST#
GND
GNT#
GND
4
GND
IPMB_PWR
HEALTHY#
V(I/O)
INTP
INTS
GND
3
GND
INTA#
INTB#
INTC#
+5V
INTD#
GND
2
GND
TCK
+5V
TMS
TDO
TDI
GND
1
GND
+5V
-12V
TRST#
+12V
+5V
GND
12-14
E
F
+5V
GND
ACK64# GND
AD[10]
GND
AD[13]
GND
C/BE[1]# GND
Keying Area
Backplanes
C/BE[2]# GND
43
Peripheral Slot: [2–P2] - [5–P2]
Pin
Z
A
B
C
D
E
F
22
GND
GA4
GA3
GA2
21
GND
Reserved
GND
Reserved
GA1
GA0
GND
Reserved
Reserved
20
GND
Reserved
GND
Reserved
GND
GND
Reserved
GND
19
GND
GND
GND
Reserved
Reserved
Reserved
GND
18
GND
Reserved
Reserved
Reserved
GND
Reserved
GND
17
GND
Reserved
GND
Reserved
Reserved
Reserved
GND
16
GND
Reserved
Reserved
Reserved
GND
Reserved
GND
15
GND
Reserved
GND
Reserved
Reserved
Reserved
GND
14
GND
AD[35]
AD[34]
AD[33]
GND
AD[32]
GND
13
GND
AD[38]
GND
V(I/O)
AD[37]
AD[36]
GND
12
GND
AD[42]
AD[41]
AD[40]
GND
AD[39]
GND
11
GND
AD[45]
GND
V(I/O)
AD[44]
AD[43]
GND
10
GND
AD[49]
AD[48]
AD[47]
GND
AD[46]
GND
9
GND
AD[52]
GND
V(I/O)
AD[51]
AD[50]
GND
8
GND
AD[56]
AD[55]
AD[54]
GND
AD[53]
GND
7
GND
AD[59]
GND
V(I/O)
AD[58]
AD[57]
GND
6
GND
AD[63]
AD[62]
AD[61]
GND
AD[60]
GND
5
GND
C/BE[5]#
GND
V(I/O)
C/BE[4]#
PAR64
GND
4
GND
V(I/O)
Reserved
C/BE[7]#
GND
C/BE[6]#
GND
3
GND
Reserved
GND
Reserved
Reserved
Reserved
GND
2
GND
Reserved
Reserved
SYSEN#
Reserved
Reserved
GND
1
GND
Reserved
GND
Reserved
Reserved
Reserved
GND
44
Backplanes
Peripheral Slot: [2–P3] - [5–P3]
Pin
Z
A
B
C
D
E
F
19
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
18
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
17
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
16
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
15
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
14
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
13
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
12
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
11
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
10
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
9
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
8
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
7
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
6
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
5
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
4
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
3
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
2
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
1
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
Backplanes
45
Peripheral Slot: [2–P4] - [5–P4]
Pin
Z
A
B
C
D
E
F
25
GND
SGA4
SGA3
SGA2
SGA1
SGA0
GND
24
GND
GA4
GA3
GA2
GA1
GA0
GND
23
GND
+12V
Reserved
CT_EN#
-12V
CT_MC
GND
22
GND
PFS0#
21
GND -SELVbat
PFS1#
20
GND
No Pin
No Pin
19
GND
No Pin
No Pin
No Pin
No Pin
No Pin
GND
18
GND
VRG
No Pin
No Pin
No Pin
VRG Rtn
GND
17
GND
No Pin
No Pin
No Pin
No Pin
No Pin
GND
16
GND
No Pin
No Pin
No Pin
No Pin
No Pin
GND
15
GND
-Vbat
No Pin
No Pin
No Pin
-Vbat Rtn
GND
11
GND
CT_D29
CT_D30
CT_D31
V(I/O)
CT_FRAME_A GND
10
GND
CT_D27
+3.3V
CT_D28
+5V
CT_FRAME_B GND
9
GND
CT_D24
CT_D25
CT_D26
GND
RF_COMP
GND
8
GND
CT_D21
CT_D22
CT_D23
+5V
CT_C8_A
GND
7
GND
CT_D19
+5V
CT_D20
GND
CT_C8_B
GND
6
GND
CT_D16
CT_D17
CT_D18
GND
CT_NETREF_1 GND
5
GND
CT_D13
CT_D14
CT_D16
+3.3V
CT_NETREF_2 GND
4
GND
CT_D11
+5V
CT_D12
+3.3V
SCLK
GND
3
GND
CT_D8
CT_D9
CT_D10
GND
SCLK-D
GND
2
GND
CT_D4
CT_D5
CT_D6
CT_D7
GND
GND
1
GND
CT_D0
+3.3V
CT_D1
CT_D2
CT_D3
GND
CT_RESET Reserved Reserved
12-14
46
Reserved Reserved
No Pin
No Pin
Reserved
GND
-SELVbat Rtn
GND
No Pin
GND
Keying Area
Backplanes
Peripheral Slot: [2–P5] - [5–P5]
Pin
Z
A
B
C
D
E
F
22
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
21
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
20
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
19
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
18
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
17
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
16
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
15
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
14
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
13
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
12
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
11
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
10
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
9
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
8
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
7
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
6
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
5
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
4
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
3
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
2
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
1
GND
Reserved
Reserved
Reserved
Reserved
Reserved
GND
Backplanes
47
Jumper Settings
Shelf Enumeration Bus Signals [JP1] - (default: 1-2 shorted)
Column 1
Column 2
Column 3
NC
SGA0
GND
NC
SGA1
GND
NC
SGA2
GND
NC
SGA3
GND
NC
SGA4
GND
PCI 33/66MHz Select [JP5]
Pin
Signal
1
M66EN
2
GND
Settings: shorted 33MHz, open 66MHz – default: open
V(I/O) Setting Jumper [J4 - J6] - (default: J4-J5 shorted)
Pin
48
Signal
J4
+5V
J5
V(I/O)
J6
+3.3V
Backplanes
3.3 cBP-3063 CompactPCI Power Backplane
The power backplane for the cPCIS-6400U 5-slot chassis is the
cBP-3063.
Specifications
X
PICMG 2.11 3U CompactPCI 47-pin Power Backplane
X
Dimension: 120.92 x 128.7 (mm, W x H)
X
Power Module Sockets: three
X
DC output (ATX connector): three
X
Cascading Current Sharing
X
Cascading Voltage Sense: Dedicated voltage sense connector
X
PICMG 2.9 IPMB Socket
Backplanes
49
Mechanical Drawing
Figure 3-5: cBP-3063 Power Backplane Front View
Figure 3-6: cBP-3063 Power Backplane Rear View
50
Backplanes
Connector Pin Assignments
CompactPCI 47-Pin PSU Connector: Power 1-3 [CN1-CN3]
Pin
Signal
Pin
Signal
47
ACL/-DC IN
31
GA2
46
ACN/+DC IN
30
V1 SENSE
45
CGND
29
V1ADJ
44
V3 SHARE
28
GA1
43
IPMB_PWR
27
EN#
42
+FAL#
26
RESERVED
41
V2 SHARE
25
GA0
40
IPMB_SDA
24
RTN
39
INH#
23
RESERVED
38
DEG#
22
RTN
37
IPMB_SCL
21
V4
36
V3 SENSE
20
V3
35
V1 SHARE
19
RTN
34
S RTN
13-18
V2
33
V2 SENSE
5-12
RTN
32
V2ADJ
1-4
V1
AC-Inlet Connector [CN4]
1
Backplanes
Pin
Signal
1
ACN/DC+
2
ACL/DC-
3
CGND
51
IPMB Connector [CN5]
Pin
Signal
1
CLK
2
GND
3
DATA
V(I/O)
ALERT#
Power Sense Connector [CN6, CN7]
1
Pin
Signal
1
Ground
2
+3.3V
3
-12V
4
+12V
5
+5V
Current Share Connector [CN8, CN9]
1
52
Pin
Signal
1
Ground
2
+3.3V
3
-12V
4
+12V
5
+5V
Backplanes
DC Power Out [CN10, CN11, C12])
Pin
Signal
Pin
Signal
1
2
+3.3V
11
+3.3V
+3.3V
12
-12V
3
GND
13
GND
4
+5V
14
INH#
5
GND
15
GND
6
+5V
16
GND
7
GND
17
GND
8
FAL#
18
-5V
9
DEG#
19
+5V
10
+12V
20
+5V
INH#1 Connector [J1]
Pin
Signal
1
INH#1
2
GND
Pin
Signal
1
INH#2
2
GND
Pin
Signal
1
INH#3
2
GND
INH#2 Connector [J2]
INH#3 Connector [J3]
Backplanes
53
DEG#/FAL# Connector [J5]
Pin
Signal
1
DEG#1
2
FAL#1
3
RSV23A
4
RSV26A
5
DEG#2
6
FAL#2
7
RSV23B
8
RSV26B
1
12
9
DEG#3
10
FAL#3
11
RSV23C
12
RSV26C
INH# Connector [J5]
54
Pin
Signal
1
INH#
2
GND
Backplanes
4
Cooling System
The cPCIS-6400U/X Series subsystems are equipped with several
fans to provide cooling for the system board, peripheral cards and
power supply units. There is one front-access intake fan at the
right side of the chassis with a replaceable air filter. Two small
exhaust fans are at the top rear of the chassis, and one large fan
provides exhaust at the left rear for the power supply units. There
is a four-fan module on the left side panel of the chassis for additional exhaust. An embedded alarm board monitors fan status
and initiates a visible and audible alarm upon fan failure.
Only cPCIS-6400U fan units are hot-swappable. Fan modules
other than the front-access intake fan require the user to manually
disconnect the power cable.
Note:
For safety reasons, only the cPCIS-6400U fans are
field serviceable by the user.
Cooling System
55
4.1 System Alarm Board
X
Supports fault alarm for up to 8 fans. If any fan faults, the
Fan LED will flash and an audible alarm will sound
X
Can detect temperature at two different locations.
X
Trigger temperature for each sensor can be set independently (50°C, 60°C, 70°C - default 50 °C).
X
Alarm mute
X
LED indicators for fan and temperature status
Mechanical Drawing
Figure 4-1: System Alarm Board Mechanical Drawing
56
Cooling System
4.2 Fan Alarm
The embedded alarm board monitors temperature & fan status.
Should a fan become disabled, the Fan LED will light up and an
audible warning will be heard. To disable the audible warning,
press the Alarm Reset button. The Fan LED will continue to flash
until the faulty fan is replaced.
Figure 4-2: Alarm LEDs and reset button
4.3 Fan Removal and Replacement Procedure
(cPCIS-6400U only)
To remove and replace a faulty fan module, follow the procedures
below. For safety reasons, only the cPCIS-6400U is field serviceable
by the user.
Front-Access Intake Fan
1. Loosen the screws attaching the front-access intake fan
module at the right side of the chassis.
2. Pull the faulty fan module out of the chassis and replace
with a functional fan module.
3. Reverse steps 1-2 to replace the fan module.
Cooling System
57
Figure 4-3: Remove the front-access intake fan module
Rear Exhaust Fans (small)
1. Loosen the screws attaching the rear exhaust fan module (small) at the top rear of the chassis.
2. Pull the fan module out, disconnect the power cable, and
replace with a functional fan module.
3. Reverse steps 1-2 to replace the fan module.
58
Cooling System
Figure 4-4: Remove the rear exhaust fan module (small)
Rear Exhaust Fan (PSU)
1. Loosen the screws attaching the rear exhaust fan module (PSU) at the right rear of the chassis as shown
below.
Figure 4-5: Remove the rear exhaust fan module (PSU)
Cooling System
59
2. Pull the fan module out, disconnect the power cable, and
replace with a functional fan module.
Figure 4-6: Disconnect the rear exhaust fan module (PSU) power cable
3. Reverse steps 1-2 to replace the fan module.
Left-Side Exhaust Fan
1. Remove the screws attaching the left-side exhaust fan
module as shown below.
Figure 4-7: Remove the left-side exhaust fan module screws
60
Cooling System
2. Lift the fan module out of the chassis from the bottom
edge, disconnect the power cables, and replace with a
functional fan module.
Figure 4-8: Remove the left exhaust fan module and
disconnect the power cables
3. Reverse steps 1-2 to replace the fan module.
For replacement fan modules, please contact your ADLINK
distributor.
4.4 Air Filter Replacement
(cPCIS-6400U only)
To ensure proper performance of the system, the air filter should
be cleaned or replaced as necessary. A replacement air filter is
supplied and can be found in the Accessory Packet.
Cooling System
61
Air Filter Removal and Replacement Procedure
1. Remove the front-access intake fan module as shown in
Figure 4.3 above.
2. Lay the fan module on its side, remove the four screws
securing the filter cover, and lift the cover to expose the
filter element.
Figure 4-9: Air filter removal and replacement
3. Clean the existing filter or replace it with the one provided.
4. Place the filter back in position, replace the filter cover
and screws, and reinstall the filter module into the chassis.
62
Cooling System
4.5 Temperature Alarm
When the subsystem’s internal temperature exceeds 50°C, the
TEMP LED will flash and an audible warning will be heard (see
Figure 5.2 above for LED location). To reset the alarm and disable
the audible warning, press the Alarm Reset button.
In order to protect the system from damage resulting from overheating, it should be shut down immediately. Inspect the operating
environment for causes of the overheating condition. After the system has cooled down sufficiently, power it up and be observant of
any future temperature alarm conditions.
4.6 Fan Specifications
SUNON KD1212PTB1-6A (right side front-access fan)
Z
Dimensions: 120 x 120 x 25mm
Z
Weight: 205 g
Z
Type: 12V DC brush-less, with ball bearing motor
Z
Rated voltage: 12V @ 0.4A
Z
Rated power: 4.8 W/each
Z
Fan speed: 3100RPM
Z
Maximum Air flow: 90 CFM/each (when zero static pressure)
Z
Noise: 44.5 dBA/each
SUNON KD1204PKVX (rear exhaust fans x2)
Z
Dimensions: 40 x 40 x 20mm
Z
Weight: 30 g
Z
Type: 12V DC brush-less, with ball bearing motor
Z
Rated voltage: 12V @ 0.13A
Z
Rated power: 1.6 W/each
Z
Fan speed: 8200RPM
Z
Maximum Air flow: 10.8CFM/each (when zero static
pressure)
Z
Noise: 27.5 dBA/each
Cooling System
63
SUNON KD1209PFV1 (rear PSU exhaust fan)
Z
Dimensions: 92 x 92 x 25mm
Z
Weight: 123 g
Z
Type: 12V DC brush-less, with ball bearing motor
Z
Rated voltage: 12V @ 0.23A
Z
Rated power: 2.8 W/each
Z
Fan speed: 3600RPM
Z
Maximum Air flow: 51 CFM/each (when zero static pressure)
Z
Noise: 37 dBA/each
SUNON KD1204PFV1 (left side fan module fans x4)
64
Z
Dimensions: 40 x 40 x 10mm
Z
Weight: 16 g
Z
Type: 12V DC brush-less, with ball bearing motor
Z
Rated voltage: 12V @ 0.08A
Z
Rated power: 1 W/each
Z
Fan speed: 7400RPM
Z
Maximum Air flow: 7.3CFM/each (when zero static pressure)
Z
Noise: 30dBA/each
Cooling System
5
Power Supply Unit
The power supply options for the cPCIS-6400 Series are as follows: The cPCIS-6400U Series is equipped with ADLINK’s cPSH325/AC CompactPCI power module and the cPCIS-6400X
Series is equipped with the APS940XA ATX power supply.
5.1 cPCIS-6400U: cPS-H325/AC
Features
X
PICMG 2.11 CompactPCI power interface compliant
X
250W 3U X 8HP Eurocard package
X
Meets IEC1000-3-2 harmonic correction
X
Internal OR-ing diodes for N+1 redundancy
X
Hot-swappable
X
Third-wire current sharing
X
EMI meets EN 55022 / FCC CLASS A
X
CE marking compliance
Specifications
X
Operating Temperature Range: 0 °C to 50°C at full load with
specified air flow (Derates linearly to 50% at +70 °C)
X
Storage Temperature: -40 to +85 °C
X
Temperature Coefficient: Typ. ±0.02% / °C
X
Cooling: >20 CFM moving air required to achieve full rated
power
X
Dimensions: Eurocard 3U X 8HP X 160mm CompactPCI
format
X
Efficiency: 78-79% typical
X
Switching Frequency: 120K Hz
X
Safety: IEC60950 Class I
X
Circuit Topology: Forward circuit
X
Transient Response: Peak transient less than 100mV and
recovers within 2mS after 25% load-change
Power Supply Unit
65
Input Characteristics
X
Input Voltage: Typ. 90 - 264 VAC
X
Power Factor Correction: Meets Harmonic Correction
IEC1000-3-2. Power Factor typ. 0.95-0.97
X
Input Connector: Positronic 47-pin PCIH47M400A1
X
Input Frequency: 47-63Hz
X
Inrush Current: Less than 30A @ 230VAC
X
Input Current: 2.8A @115VAC / 1.4A @230VAC
X
Dielectric Withstand: Meets IEC950 regulations
X
EMI: Meets EN55022 / FCC Class A
X
Hold-up Time: 5mS after power fail signal
X
Remote ON/OFF: Available at [INH#] & [EN#] pins
X
Power Fail Signal: Available at [FAL#] pin
X
Status LED: <Green> means valid input voltage; <Amber>
means a critical fault.
X
Thermal Protection (OTP): Installed NTC and thermostat for
thermal sensor at [DEG#] pin
X
Power OK: Installed at all outputs
X
Leakage Current: Typ. 0.5mA
Output Characteristics
Output Voltage
(see below for properties)
66
Output Current (A)
MIN.
MAX.
TYP.
PEAK.
5V
MAIN +VO1
(1, 2, 3, 4, 6)
2.0
33.0
25.0
–
3.3V
AUX. +VO2
(1, 2, 3, 4, 6, 7)
0
33.0
18.0
–
12V
AUX. +VO3
(1, 2, 3, 4, 6, 7)
0
5.5
5.5
6.0
-12V
AUX. –VO4
(1, 5, 6, 8, 9)
0
1
0.5
1.5
Power Supply Unit
Properties
Remarks
1: OVP built-in
2: Adjustable
3: Remote sensing
4: 3rd-wire Load Sharing
5: Droop Current Sharing
6: Installed with Or-ing diode
7: Magnetic Amplifier
8: Installed with Post-regulator
9: Common Choke
Peak load sustainable for less than 60sec. with duty cycle
<10%. Max. load is the continuous operating load of each
rail. Max. load of each rail cannot be drawn from all outputs
at the same time.
X
Over Load Protection: Fully protected against output overload or short circuit. Typical 120% max. load.
X
Over Current Protection: Installed at each rail
X
Output Wattage: Typ. 250W continuous.
X
Output Connector: Positronic 47-pin PCIH47M400A1.
X
Line Regulation: Typ. 0.1%.
X
Load Regulation: Typ. ±1–2%.
X
Noise & Ripple: Typ. 1% peak to peak or 50mV, whichever
is greater.
X
OVP: Built-in at all outputs.
X
Adjustability: Available at VO1, 2 & 3.
X
Output Trim: Electrical trim available at VO1/VO2 [ADJ #].
X
Remote Sensing: Available at VO1, VO2 & VO3.
X
Hot-Swap: Available.
X
N+1 Redundancy: Installed with internal OR-ing diodes at
all outputs for N+1 redundancy operation.
X
Current Sharing: Third-wire current sharing at VO1,2 &3.
X
Power OK Signal: Available for all output.
X
Over Current Protection: Installed at each rail.
X
Overload Protection: Fully protected against output overload or short circuit. Typical 120% max. load.
Power Supply Unit
67
5.2 cPCIS-6400X: APS940XA ATX 400W
Features
X
Active PFC (full range)
X
12V Max. Current : 30A
X
Noise & Thermal Control
Specifications
X
Operating Temperature Range: -10°C – 40°C
X
Cooling: one 80mm DC fan
X
Active Power Factor Correction meets IEC-1000-3-2
CLASS D
X
Dimensions: 140.00x150.00x86.00 (mm)
X
Hold Up Time: 16 ms minimum at full load & normal input
voltage
X
Dielectric Withstand: input/output 1500 VAC for 1 sec.
input to frame ground 1500 VAC for 1 sec.
X
Efficiency: 68% typical
X
Power Good Signal: on delay 100 ms to 500 ms, off delay 1
ms
X
Over Load Protection: 130 +/- 20%
X
Over Voltage Protection:
5V – 5.7V – 6.5V; 3.3V – 3.9V – 4.3V; 12V – 13.6V – 15V
X
Short Circuit Protection: +5V, -5V, +12V, -12V, +3.3V
X
EMI Noise Filter: FCC CLASS B, CISPR22 CLASS B
X
Safety: UL 1950, CSA 22.2 NO/ 950, TUV IEC 950
X
MTBF: 102,391
Input Characteristics
68
X
Voltage: 90 – 240 VAC Full Range
X
Frequency : 47 – 63 HZ
X
Input Current:
X
Inrush Current: 65A MAX. FOR 115 VAC
125A MAX. FOR 230 VAC
8.0 A (RMS) FOR 115 VAC
4.0 A (RMS) FOR 230 VAC
Power Supply Unit
Output Characteristics
Output Current(A)
Regulation
Output
Output
Voltage
MIN.
MAX.
PEAK
LOAD
LINE
Ripple& Noise
Max[P-P]
5V
3
35
–
± 5%
± 1%
50mV
12V
2
30
–
+7 – -5%
± 1%
120mV
-5V
0
0.8
–
± 5%
± 1%
150mV
-12V
0
1.0
–
± 5%
± 1%
150mV
3.3V
1
25
–
± 5%
± 1%
50mV
+5VSB
0.1
2
–
± 5%
± 1%
50mV
Note:
The output current of 5V & 3.3V must not exceed 45A.
Power Supply Unit
69
70
Power Supply Unit
Important Safety Instructions
Please read and follow all instructions marked on the product and
in the documentation before operating the system. Retain all
safety and operating instructions for future use.
X
Please read these safety instructions carefully.
X
Please keep this User’s Manual for future reference.
X
The equipment should be operated in an ambient temperature between 0 and 40°C for the cPCIS-6400X and 50°C for
the cPCIS-6400U.
X
The equipment should be operated only from the type of
power source indicated on the rating label. Make sure the
voltage of the power source is correct when connecting the
equipment to the power outlet.
X
If the user’s equipment has a voltage selector switch, make
sure that the switch is set to the proper position for the area.
The voltage selector switch is set at the factory to the correct voltage.
X
For pluggable equipment, ensure they are installed near a
socket-outlet that is easily accessible.
X
Secure the power cord to prevent unnecessary accidents.
Do not place anything over the power cord.
X
If the equipment will not be in use for long periods of time,
disconnect the equipment from mains to avoid being damaged by transient overvoltage.
X
All cautions and warnings on the equipment should be
noted.
X
Please keep this equipment away from humidity.
X
Do not use this equipment near water or a heat source.
X
Place this equipment on a reliable surface when installing.
A drop or fall could cause injury.
X
Never pour any liquid into the opening, this could cause fire
or electrical shock.
Important Safety Instructions
71
X
Openings in the case are provided for ventilation. Do not
block or cover these openings. Make sure there is adequate
space around the system for ventilation when setting up the
work area. Never insert objects of any kind into the ventilation openings.
X
To avoid electrical shock, always unplug all power and
modem cables from the wall outlets before removing covers.
X
Lithium Battery provided (real time clock battery)
“CAUTION - Risk of explosion if battery is replaced by
an incorrect type. Dispose used batteries as instructed
in the instructions”
X
X
72
The equipment should be checked by service personnel if
one of the following situation arises:
Z
The power cord or plug is damaged.
Z
Liquid has penetrated the equipment.
Z
The equipment has been exposed to moisture.
Z
The equipment is not functioning or does not function
according to the user’s manual.
Z
The equipment has been dropped and damaged.
Z
If the equipment has obvious sign of breakage.
Never open the equipment. For safety reasons, the equipment should only be opened by qualified service personnel.
Important Safety Instructions
Warranty Policy
Thank you for choosing ADLINK. To understand your rights and
enjoy all the after-sales services we offer, please read the following carefully.
1. Before using ADLINK’s products please read the user manual and follow the instructions exactly. When sending in
damaged products for repair, please attach an RMA application form which can be downloaded from: http://
rma.adlinktech.com/policy/.
2. All ADLINK products come with a limited two-year warranty, one year for products bought in China:
X
The warranty period starts on the day the product is
shipped from ADLINK’s factory.
X
Peripherals and third-party products not manufactured
by ADLINK will be covered by the original manufacturers' warranty.
X
For products containing storage devices (hard drives,
flash cards, etc.), please back up your data before sending them for repair. ADLINK is not responsible for any
loss of data.
X
Please ensure the use of properly licensed software with
our systems. ADLINK does not condone the use of
pirated software and will not service systems using such
software. ADLINK will not be held legally responsible for
products shipped with unlicensed software installed by
the user.
X
For general repairs, please do not include peripheral
accessories. If peripherals need to be included, be certain to specify which items you sent on the RMA Request
& Confirmation Form. ADLINK is not responsible for
items not listed on the RMA Request & Confirmation
Form.
Warranty Policy
73
3. Our repair service is not covered by ADLINK's guarantee
in the following situations:
X
Damage caused by not following instructions in the
User's Manual.
X
Damage caused by carelessness on the user's part during product transportation.
X
Damage caused by fire, earthquakes, floods, lightening,
pollution, other acts of God, and/or incorrect usage of
voltage transformers.
X
Damage caused by unsuitable storage environments
(i.e. high temperatures, high humidity, or volatile chemicals).
X
Damage caused by leakage of battery fluid during or
after change of batteries by customer/user.
X
Damage from improper repair by unauthorized ADLINK
technicians.
X
Products with altered and/or damaged serial numbers
are not entitled to our service.
X
This warranty is not transferable or extendible.
X
Other categories not protected under our warranty.
4. Customers are responsible for shipping costs to transport
damaged products to our company or sales office.
5. To ensure the speed and quality of product repair, please
download an RMA application form from our company website: http://rma.adlinktech.com/policy. Damaged products
with attached RMA forms receive priority.
If you have any further questions, please email our FAE staff:
[email protected]
74
Warranty Policy
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement