Viper FANG 20T Specifications

Add to my manuals
28 Pages

advertisement

Viper FANG 20T Specifications | Manualzz

TABLE OF CONTENTS

SAFETY PRECAUTIONS

MACHINE COMPONENTS

MACHINE SET UP

MACHINE INSTALLATION

MACHINE OPERATION

3

4

5

5-6

6

BATTERY CHARGING

PREVENTATIVE MAINTENANCE

MACHINE STORAGE

BASIC TROUBLESHOOTING

7-8

8-9

9

10

PARTS BREAKDOWNS AND LISTS 11-27

2

SAFETY PRECAUTIONS

This machine is intended for commercial use. It is constructed for use in an indoor environment and is not intended for any other use. Use only with recommended accessories.

All operators shall read, understand and exercise the following safety precautions:

1) DO NOT OPERATE MACHINE: x Unless trained and authorized. x Unless you have read and understand the operators manual. x In flammable or explosive areas. x If not in proper operating condition. x In outdoor areas.

2) BEFORE OPERATING MACHINE: x Make sure all safety devices are in place and operate properly.

3) WHEN USING MACHINE: x Go slow on inclines and slippery surfaces.

x Follow all safety guidelines. x Be very careful when using the machine in reverse. x Report and fix any damage to machine prior to operating it.

4) BEFORE LEAVING OR SERVICING

MACHINE: x Stop machine on level ground. x Turn machine off.

5) WHEN SERVICING MACHINE: x Read operators manual thoroughly prior to operating or servicing this machine. x Use manufacturer supplied or approved replacement parts. x Secure machine with wheel blocks prior to jacking the machine up. x Use approved jack or hoist to safely elevate the machine.

WHEN SERVICING MACHINE: (con’t) x Disconnect batteries prior to working on machine. x Wear gloves when handling batteries or battery cables. x Avoid any contact with battery acid. x Avoid moving parts. Do not wear loose fitting clothing while servicing machine.

: Batteries emit hydrogen gas.

Explosion or fire can result from hydrogen gas.

Keep sparks and open flames away! Keep battery compartment open when charging.

: Flammable materials can cause an explosion or fire. Do not use flammable materials in tanks.

: Flammable materials or reactive metals can cause explosion or fire. Do not pick up.

3

19

MACHINE COMPONENTS

1 2 3 4 5 6 7 8

30 31

20 21

15

14

18

17

16

13

1. Main power ON/OFF switch

2. Vacuum ON/OFF switch

3. Battery level meter

4. Brush ON/OFF switch

5. Brush pressure meter

6. Solution ON/OFF switch

7. Brush pressure UP/DOWN switch

8. Solution control knob

9. Speed control knob

10. Circuit breakers

11. Recovery tank drain hose

12. Squeegee adjustment nut & shaft

13. Squeegee assembly

14. Scrub head actuator

15. Solution tank level sight tube

12

10

11

9

29

28

27

26 25 24

16. Console adjustment levers

17. Rear solution fill

18. Reverse switch

19. Squeegee lift lever

20. Control housing

21. Operating triggers

22. Solution tank

23. Rear casters

24. Transport wheels

25. Scrub head

26. Scrub head skirt

27. Skirt housing latch

28. Protective rollers

29. Front solution fill

30. Recovery tank

31. Recovery tank lid

22

23

4

MACHINE SET UP & INSTALLATION

UNCRATING MACHINE

Be sure and check packing carton for any damage.

Immediately report any damage to carrier. Check contents of package to ensure that the following items are included: Machine, batteries (x2), squeegee assembly, battery charger, and pad driver.

BATTERY CONNECTIONS

The batteries are and charger are shipped separately and will need to be installed and connected as shown in the diagram below.

: Batteries emit hydrogen gas.

Explosion or fire can result from hydrogen gas.

Keep sparks and open flames away! Keep battery compartment open when charging.

1. Be sure power switch is in the “off” position.

2. Open recovery tank to gain access to battery compartment.

3. Carefully place the two batteries into the compartment as shown in figure below. Place the battery brace at the rear of the two batteries. DO NOT DROP BATTERIES

INTO COMPARTMENT!

4. Connect battery cables to posts in numbered order as shown in drawing below. (RED to

POSITIVE and BLACK to NEGATIVE)

R E D

2. Check battery meter to make sure batteries are fully charged. (see BATTERY CHARGING)

3. Check that squeegee is properly installed.

4. Check that brush / pad is properly installed.

INSTALLING PAD DRIVER OR BRUSH

1. Ensure that the machine is turned off

2. Raise the brush head assembly off the floor by pushing on the brush lift button on the control console.

3. Open the swing away skirts to gain access to the brush head assembly.

4. If using a pad driver, first attach the appropriate pad to the pad driver surface.

5. Mount the pad driver or brush to the drive motor hub by lining up the three studs with the three holes in the drive motor hub. Once in the holes, rotate the driver toward the spring clip to lock driver into place.

MOUNTING THE SQUEEGEE

1. Pull back on the squeegee lift lever to raise the squeegee bracket up.

2. Loosen the two knobs on the squeegee and slide the squeegee into the slots at the rear of the squeegee bracket. (the wheels on the squeegee point to the back)

3. Tighten the knobs securely.

4. Secure the vacuum hose on the pick-up tube of the squeegee.

B L A C K

B A T T E R Y B R A C E

C H A R G E R P L U G

5. Apply a coat or protective spray on the cable connections to prevent battery corrosion.

MACHINE SET UP

PRE-OPERATION CHECKS

1. Sweep or dust mop the surface to be cleaned.

FILLING THE SOLUTION TANK

1. The Fang 20HD can be filled in two different locations: a. Front fill area for use with a hose or a bucket. b. Rear fill area for use with a hose only.

2. Determine which fill area you would like to use to fill the machine with water.

3. Fill solution tank with up to

15 gallons of water. (water temperature should not exceed

140° F) The clear tube in the back left of the

5

machine has gallon markers to help determine the water level in the solution tank

: If you are filling the solution tank with a bucket, make sure the bucket is clean. This will prevent debris from clogging the lines or solenoid.

: Do not put any flammable materials into solution tank. This can cause an explosion or a fire. Only use recommended cleaning chemicals.

Contact your janitorial supply distributor for recommendations on proper chemicals.

MACHINE OPERATION

: Do not operate machine unless you have read and understand this manual.

1. Set control housing to a comfortable operating height by squeezing together the two thumb levers directly underneath the housing. (see machine components, item #16)

2. Lower squeegee assembly to the floor by releasing the lift lever from its locked position.

(see machine components, item #19)

3. Lower the brush head assembly to the floor by pushing on the brush lift button on the control console. (see machine components, item #7)

4. Turn main power to “on” position. (see machine components, item #1)

5. Turn vacuum motor switch to “on” position.

(see machine components, item #2)

6. Turn the brush motor switch to “on” position.

(see machine components, item #4) a. Brushes will not spin until the operating triggers are pulled.

7. Turn the solution switch to “on” position. (see machine components, item #6) a. Solution will not begin to flow until the operating triggers are pulled.

8. To begin scrubbing, pull on one or both of the red operating triggers. (see machine components, item #21) When these triggers are pulled, the brush will begin to spin, the solution will begin to flow, and the machine will propel itself.

9. This machine is self-propelled. The speed can be controlled by a dial located on the right side of the control housing. (see machine components, item #9)

10. This machine has reverse. In order to activate reverse, there is a toggle switch located on the left side of the control housing. (see machine components, item #18) The toggle switch must be pulled backwards and the red operating triggers must be pressed to activate reverse motion.

: Do not keep the machine in the same position with the pad / brush spinning, or you could cause damage to the floor.

11. Adjust amount of solution flow by turning the solution control knob. Turn to the right for more solution, or turn left for less solution.

(see machine components, item #8)

WHILE OPERATING MACHINE

1. Occasionally look through the clear recovery tank lid to see if there is any foam build-up. If excessive foam is found, add defoamer to the recovery tank. screen, or damage can occur to the vacuum motor.

Foam will not activate the machines float shut-off device.

: Foam must not enter the float shut-off

2. Occasionally view the clear tube at the back left of the machine to check the amount of cleaning solution that is left in the machine.

3. Occasionally check the battery level meter.

(see machine components, item #3) damage may result. the blades down with a damp cloth.

When meter is in the red, recharge the batteries.

: When battery meter is in the red, do not continue to operate the machine. Battery

4. If the squeegee assembly leaves streaks on the floor, raise the squeegee off the floor and wipe

: Do not use your fingers to wipe or remove debris from the blades, as injury may occur.

5. When the solution tank runs empty, turn off the brush switch, solution switch and raise the brush head. Keep the squeegee down and continue to vacuum until all the dirty water is

6

picked up. (see TANK DRAINING section to learn how to drain recovery and solution tanks)

: The brush motors are circuit breaker protected to protect them from damage. If a breaker trips, it can’t be reset immediately. You must first determine what caused the breaker to trip, and allow the motor to cool down before you can reset the breaker. The breakers are located on the back panel of the control housing.

TANK DRAINING

1. Turn the power off on the machine

2. With the squeegee and brush head in their

“up” position, transport machine to approved area for draining tank(s).

DRAINING THE RECOVERY (DIRTY) TANK

: Anytime scrubbing is completed, or when refilling solution tank, the recovery tank should be drained and cleaned.

: If the recovery tank is not drained when the solution tank has been refilled, foam or water may enter the float shut-off mechanism and cause damage to the vacuum motor.

1. Remove the drain hose from the holder, and place the drain hose over the floor drain.

Twist off the drain hose plug to begin the draining process. In order to completely empty the recovery tank, hinge open the recovery tank and let it rest on the support stand.

2. Clean the recovery tank after every use. Use a fresh water hose to rinse out the recovery tank.

Be careful not to spray water into the float shut-off mechanism.

: If you are storing the machine for any period of time, always leave the clear recovery tank lid off the tank so the tank can dry completely and smell fresh.

3. Replace the drain hose plug tightly as soon as you are done draining the tank.

DRAINING THE SOLUTION (CLEAN) TANK

: Anytime scrubbing operation is completed, the solution tank should be drained and cleaned.

1. Pull down on the clear tube (back left of the machine) to remove it from the hose barb.

This will allow the solution to flow freely into a bucket or floor drain.

2. Rinse the solution tank with clean water after every use. This will help prevent chemical buildup and clogging of the solution lines.

3. With clean water in solution tank, turn machine power on, solution switch “on” and pull the operating triggers. This will allow the clean water to flush through and clean the solution plumbing.

4. Once tank is rinsed, flushed and drained, reconnect the clear tube to the hose barb. Be sure the tube is pushed all the way up on the hose barb.

BATTERY CHARGING

: Use only approved chargers with the following specifications: x Automatic shut off circuit x Deep cycle charging x Output current of 10 – 20 amps x Output voltage of 24 volts

: For the best machine performance, keep batteries charged at all times. Do not let them sit in a discharged condition.

: Batteries are dangerous! Batteries emit hydrogen gas and an explosion or fire can result.

Keep sparks and fire away from batteries at all times. When charging the machine, make sure the battery compartment is left open.

1. Place charger and machine in a well ventilated area.

2. Turn machine off.

3. Open recovery tank up, exposing battery compartment

4. Check fluid level in each battery cell. Do not charge batteries unless fluid is slightly covering the battery plates. Do not overfill the

7

batteries. Overfilling may cause the batteries to overflow during charging due to expansion.

Replace the caps prior to charging.

5. Plug approved charger into grounded wall outlet before plugging the charger into the machine.

6. Plug charger into red charger receptacle located in the front left of the battery

7. compartment.

DAILY MAINTENANCE

1. Remove pad driver / brush and clean with approved cleaner.

2. Drain recovery and solution tanks completely and rinse out with clean water. Visually check the recovery tank for debris and clean out as necessary.

3. Raise squeegee assembly off floor and wipe it down with a damp towel. Be sure to store the squeegee in the up position.

4. Remove the float shut-off assembly and rinse it out with clean water.

8. Flip up the recovery tank “kick stand” and gently lay the recovery tank down until it rests on the stand.

9. The charger will automatically begin to charger the batteries, and it will automatically shut down once the batteries are fully charged.

10. Upon completion of charging, first unplug the charger from the wall outlet, and then disconnect the charger from the machine.

11. Check the battery level after charging is complete. If fluid level is low, add distilled water to bring the fluid level up to the bottom of the sight tubes. Replace the caps and wipe the batteries down with a towel.

PREVENTATIVE MAINTENANCE

: Before performing any maintenance on the machine, be sure that the power is turned off, or the batteries are disconnected!

: Repairs are to be completed by

Authorized Service Centers only. Any repairs completed by unauthorized persons will void the warranty.

5. Clean machine with an approved cleaner and a damp towel.

6. Recharge batteries.

WEEKLY MAINTENANCE

1. Check fluid level in batteries.

2. Check batteries for loose or corroded cables.

3. Keep battery tops clean from corrosion.

MONTHLY MAINTENANCE

1. Check machine for leaks and loose fasteners.

2. Lubricate all grease points and pivot points with silicon spray and approved grease.

3. Place machine over a floor drain. Flush solution system by pouring 3 gallons of hot water and approved alkaline detergent into the solution tank and running machine (with solution control on) for 45 seconds. Turn machine off and let it sit overnight. Then next day, drain the remaining solution and rinse the solution tank out with clean water.

8

VACUUM MOTOR MAINTENANCE

1. Contact your local Viper Distributor for any motor maintenance.

2. Vacuum motor should have the brushes checked every 250 hours. Brushes should be replaced when they are worn to a length of

10mm or less.

BATTERY MAINTENANCE

: For the best machine performance, keep batteries charged at all times. Do not let them sit in a discharged condition.

: Batteries are dangerous! Batteries emit hydrogen gas and an explosion or fire can result.

Keep sparks and fire away from batteries at all times.

: Whenever servicing batteries, be sure to wear protective gloves. Avoid contact with battery acid at all times!

1. Always follow the battery charging directions as outlined in the BATTERY CHARGING section of this manual.

2. Keep battery tops and terminals free from corrosion. A strong solution of baking soda and water is the best way to keep the batteries corrosion free. DO NOT ALLOW THE

BAKING SODA / WATER SOLUTION TO

ENTER THE BATTERY CELLS.

3. Use a wire brush with the baking soda solution to properly clean the battery posts and connections.

4. Check battery connections for wear and loose terminals. Replace if necessary.

MACHINE STORAGE

1. Always store the machine indoors.

2. Always store the machine in a dry area.

3. Always store the machine in its upright position.

4. Always store the machine with the pad driver / brush raised off the floor.

5. Always store the machine with the squeegee assembly raised off the floor.

6. If storing in an area which may reach freezing temperatures, be sure to drain all fluids from the machine prior to storage. Any damage caused by freezing temperatures will not be covered by the warranty.

7. Drain the recovery tank and remove the clear on the top of the recovery tank so that it can

“breathe” during storage.

8. Drain the solution tank of all fluid.

9

BASIC TROUBLESHOOTING

PROBLEM

No power

Brush motor does not run

Vacuum motor does not run

Short run time

Little or no solution flow

Poor water pick up

CAUSE

Bad batteries

Key not in "ON" position

Main circuit breaker tripped

Batteries need to be charged

Loose battery cable

Batteries not connected properly

Bad brush switch

Brush circuit breaker has tripped

Bad wiring

Bad brush motor

Carbon brushes worn out

Bad solenoid

Bad vacuum switch

Bad wiring

Bad vacuum motor

Carbon brushes worn out

Batteries need to be charged

Batteries need maintenance

Bad cell in battery(s)

Bad charger

Bad solution switch

Clogged solution solenoid

Clogged solution filter

Solution line obstructed

Solution flow adjustment knob in need of adjustment

Squeegee clogged

Squeegee blades worn

Squeegee not mounted correctly

Vacuum hoses have a hole or are loose

Vacuum hose may be clogged

Drain hose stopper is loose

Batteries need to be charged

Vacuum motor is loose

Recovery tank lid is loose

Recovery tank inlet hole is clogged

Recovery tank is full

Float shut off is clogged

SOLUTION

Replace batteries

Turn key "ON"

Contact Viper Distributor

Charge batteries (see Battery Charging)

Tighten loose cable(s)

Follow battery installation instructions

Contact Viper Distributor

Check brush motor for obstructions and reset breaker

Contact Viper Distributor

Contact Viper Distributor

Contact Viper Distributor

Contact Viper Distributor

Contact Viper Distributor

Contact Viper Distributor

Contact Viper Distributor

Contact Viper Distributor

Charge batteries (see Battery Charging)

See Battery Maintenance in this manual

Replace batteries

Replace charger

Contact Viper Distributor

Contact Viper Distributor

Remove filter and clean

Remove solution line and clean

Increase flow by twisting solution adjustment knob to the right. Decrease flow by twisting solution adjustment knob to the left.

Clean debris off squeegee with damp towel

Install new squeegee blades

Confirm that the squeegee assembly is securely fastened to the machine and not loose fitting.

Check hose connections and make sure they are firm.

Replace hose if damaged.

Check hose for debris and remove any clog.

Tighten drain plug.

Charge batteries (see Battery Charging)

Tighten vac motor mounting screws. Do not overtighten or damage will occur.

Confirm the clear recovery tank lid is securely in place.

Drain recovery tank and tilt tank on side. Check the inlet hole for debris and remove debris.

Drain recovery tank.

Remove float shut off from inside recovery tank and remove any debris.

10

11

FANG20HD - SOLUTION TANK ASSEMBLY

DIA

NO

33

34

35

36

37

38

39

40

41

42

28

29

30

31

32

23

24

25

26

27

12

13

14

15

16

7

8

9

10

11

3

4

1

2

5

6

17

18

19

20

21

22

PART

NUMBER

VF81715

VF82067

VF14232

VF82078

VF13543

VF13544

VA13483

VF82081

VF82079

VF82801

VF82071

VF99001

VF83129

VF13514A

VF13635

BAT195I

VF83111

VF83140

VF82072A

VF13634

VF81405BD

VA13477

VV13664

VV13604

VF13519

VF82154

VF13535

VF81406

VF81404

VF82029A

VF82032

VF82030

VF82031A

VF82070

VF81306

VF81747

VF82123

VF13633

VV13607

GT13032

VF81748

VF13495

DESCRIPTION

ǂǂǂ GRIP,HANDLE

ǂǂǂ SCREW, SELF-TAPPING, ST, M4 X 16

WASHER,PLAIN, M4 X M12 X 1

ǂǂǂ SCREW, M8 X 20

ǂǂǂ WASHER,LOCK, M5 X M11 X 28

ǂǂǂ PLUG,EXPANSION

ǂǂǂ WASHER,PLAIN, M8 X M20 X 2

ǂǂǂ BUSHING

ǂǂǂ SUPPORT,RECOVERY TANK

ǂǂǂ BRACKET,VAC TUBE

ǂǂǂ SPRING

ǂǂǂ ADAPTER,TUBE

ǂǂǂ GASKET,TUBE ADAPTER

ǂǂǂ LABEL,LEFT

ǂǂǂ CONNECTOR, 175A

ǂǂǂ WIRE, #6 X 750

ǂǂǂ DECAL

ǂǂǂ SCREW, M6 X 35

ǂǂǂ WASHER,LOCK, M6

ǂǂǂ WASHER,PLAIN, M6 X M16 X 1.5

ǂǂǂ WIRE, #6 X 750

ǂǂǂ SCREW, M6 X 16

ǂǂǂ STANDOFF

ǂǂǂ BRACKET

ǂǂǂ SCREW, M6 X 10

ǂǂǂ SCREEN,FILL

ǂǂǂ SCREW, SELF-TAPPING, ST, M4 X 16

ǂǂǂ SCREW, SELF-TAPPING, ST, M4 X 10

ǂǂǂ WASHER,PLAIN, M4 X M9 X 0.8

ǂǂǂ PLUG,FILL SCREEN

ǂǂǂ COVER,FILL SCREEN

ǂǂǂ SOLUTION TANK

ǂǂǂ LABEL,RIGHT

ǂǂǂ WHEEL, 4"

ǂǂǂ BUSHING

ǂǂǂ WASHER,PLAIN, M8 X M16.5 X 1

ǂǂǂ SCREW, M8 X 50

ǂǂǂ BATTERY,12V,195AMP HOUR

ǂǂǂ CASTER, 4"

ǂǂǂ TRAY,BATTERY

ǂǂǂ SPACER,BATTERY

ǂǂǂ SCREW, M10 X 30

12

NO

REQ'D

2

2

1

2

2

2

1

8

2

1

1

1

6

7

1

2

1

2

1

2

1

2

1

1

1

1

1

8

1

1

1

6

1

3

6

1

8

6

1

2

1

4

DIA

NO

43

44

48

49

50

51

52

45

46

47

53

54

55

56

57

58

59

60

61

62

63

64

FANG20HD - SOLUTION TANK ASSEMBLY

PART

NUMBER

VF82403

VF81724

VF81724R

CHRGR18

VF13537

VF13518

VF14234

VF13513

VF81408

VF81416

VF82161

VF81123

VF82306A

VF14230

VV13601

VF13532

VF81202

VF14235

VF48216

VF83124

VF82050A

VF14248

VA13516

DESCRIPTION

CABLE,BATTERY

CAPS,BATTERY,BLACK

CAPS,BATTERY,RED

CHARGER,24V,18AMP

WASHER,PLAIN, M10 X M26 X 2

WASHER,LOCK, M10

SCREW, M8 X 16

NUT, M8

PLATE,LOCK

HOSE BARB

CLAMP (16-25)

TUBING

KIT,LABEL,MARKERS

SCREW, M5 X 15

WASHER,LOCK, M5

WASHER,PLAIN, M5 X M11 X 2

PLATE,SQGE,LOCK

SCREW, M8 X 35

WASHER,LOCK, M12.7

HANDLE,SQGE,LIFT

BUSHING

SCREW, M8 X 100

WASHER,PLAIN, M10 X M30 X 1.5

NO

REQ'D

1

1

1

1

1

1

3

3

1

1

3

1

2

1

1

2

8

8

2

2

2

2

1

13

14

DIA

NO

7

8

9

10

11

12

13

14

15

16

17

1

4

5

2

3

6

24

25

26

27

28

29

18

19

20

21

22

23

30

31

PART

NUMBER

VF82010

VF82083

VF82009

VV13607

VF13533

VF14233

VF81504

VF82802

VF13528

VF13495

VF82028

VF81509

VF81510-9

VF81510-2

VF81510A

VV10113

VF83154

ZD53000

VF13502

VF82310

VF13521

VF81503

VF14200

GT13032

VF82011

VF82082

VA13477

VV13664

VF82010A

VF82010B

VF82010X

FANG20HD - RECOVERY TANK ASSEMBLY

DESCRIPTION

NO

REQ'D

CLEAR COVER,RECOVERY TANK

DECAL WARNING BATTERY

ELBOW ADAPTOR,FLOAT

WASHER,LOCK, M6

1

WASHER,PLAIN, M6 X M16 X 2

SCREW, M6 X 20

FLOAT

RECOVERY TANK (FANG20HD)

WASHER,TEETH,LOCK, M6

SCREW, M6 X 16

CABLE

PLUG,EXPANSION

STRAP,DRAINHOSE

SLEEVE,DRAINHOSE

DRAIN HOSE ASEMBLY

CLAMP, 2"

DECAL,BATTERY INSTALLATION 1

MOTOR,VAC 2 STAGE,24VDC 1

1

2

1

1

2

2

1

1

1

1

1

1

13

7

4

NUT,LOCK, M6 3

STUD(20") 3

NUT,M6

SEAT

SCREW, M6 X 16

WASHER,PLAIN, M6 X M16 X 1.5

3

1

9

HINGE,RECOVERY TANK

LOGO (20")

SCREW, SELF-TAPPING, ST, M4 X 1

WASHER,PLAIN, M4 X M12 X 1

RUBBER HINGE

4

1

1

4

9

1

GASKET

KIT,LID

1

1

15

16

DIA

NO

1

2

3

22

23

24

25

26

17

18

19

20

21

11

12

13

14

15

16

4

7

8

5

6

9

10

FANG20HD - BRUSH LIFT/DRIVE ASSEMBLY

PART

NUMBER

VF82080

VF81106

VF81600

ZD72000A

VF81102

VF13537

VF13518

VF13636

VF13634

VF13502

VF13533

VF81103

VF82016A

VF13538

VF82803

VF83139

VF14084

VF81301

VF13519

VV13604

VF13535

VF83126

VF83135

VF83115

VF14247

VF81101A

VF13501

DESCRIPTION

HUB,CAPS

WHEEL, 8"

TRANSAXLE, 24"

TRANSAXLE MOTOR, 24VDC

BRACKET,TRANSAXLE MOUNT

WASHER,PLAIN, M10 X M26 X 2

WASHER,LOCK, M10

SCREW, M10 X 45

SCREW, M10 X 30

NUT,LOCK, M6

WASHER,PLAIN, M6 X M16 X 2

SPACER

BUSHING

WASHER,PLAIN, M12 X M22 X 2

BRACKET,LIFT MOTOR

PIN, M10 X 30

PIN,COTTER, M3.2 X 24

ACTUATOR

WASHER,LOCK, M8

SCREW, M8 X 20

WASHER,PLAIN, M8 X M20 X 2

BRACKET,CABLE GUIDE

BRACKET,ACTUATOR

PLATE

SCREW, M12 X 25

PLATE,BASE TRANSAXLE

NUT,LOCK, M12

NO

REQ'D

2

1

1

1

2

4

4

1

4

1

4

1

4

2

2

2

4

2

6

6

8

8

1

1

2

2

2

17

18

DIA

NO

1

18

19

20

21

22

23

24

25

26

27

28

7

8

9

10

11

12

4

5

2

3

6

13

14

15

16

17

35

36

37

38

39

40

29

30

31

32

33

34

41

42

PART

NUMBER

VF83112A

DESCRIPTION

VA13400

GT13022

VF14234

VF13519

VF13542

ǂǂǂ BLOCK,GUIDE

ǂǂǂ WASHER,PLAIN, M5 X M11 X 1

ǂǂǂ NUT,LOCK, M5

ǂǂǂ SCREW, M8 X 16

ǂǂǂ WASHER,LOCK, M8

ǂǂǂ WASHER,PLAIN, M8 X M26 X 2

VV20274B

VF83116A

VF13535

VV13604

ǂǂǂ

ǂǂǂ

ǂǂǂ

ǂǂǂ

WASHER,PLAIN, M13 X M39 X 2

SUPPORT PLATE,SKIRT

WASHER,PLAIN, M8 X M20 X 2

SCREW,M8X20

VF13538

VF82805

ǂǂǂ

ǂǂǂ

WASHER,PLAIN,M12XM22X2

BRACKET,SPRING

VF14247 ǂǂǂ SCREW,M12X25

VF82016A ǂǂǂ BUSHING

VF83117

VF14238

ǂǂǂ SPRING

ǂǂǂ SCREW,M12X30

VF82804 ǂǂǂ BRACKET,MOTOR MOUNT

VF14225A ǂǂǂ SCREW,M6X40

VF83133 ǂǂǂ STUD

VF82057

VF13502

ǂǂǂ

ǂǂǂ

PAD DRIVER, 19" (FANG20T)

NUT,LOCK, M6

VF83118 ǂǂǂ SPACER

VF99003A ǂǂǂ BIG MOUTH

VA13484 ǂǂǂ SCREW,SELF-TAPPING,ST, M4 X 12

MF-VF002-4A ǂǂǂSCREW,SELF-TAPPING, 1/4" - 1"

VF14241

VV20298

VF82058

VF83130A

VF83130

VF83134

VF83132

VF83131

VV13601

ǂǂǂ

ǂǂǂ

ǂǂǂ

ǂǂǂ PLATE, DRIVE, ASSY

ǂǂǂ PLATE,DRIVE

ǂǂǂ STOP,DRIVE RELEASE

ǂǂǂ

ǂǂǂ CLAMP,BRUSH PLATE

ǂǂǂ

SCREW, 5/16" - 1"

WASHER,LOCK, 5/16"

WASHER

SPRING

WASHER,LOCK, M5

VF13545

VF14242

VV13620

VF13537

ǂǂǂ

ǂǂǂ

ǂǂǂ

ǂǂǂ

SCREW,SELF-TAPPING,ST,M5 X 10

SCREW, 3/8" - 1"

WASHER,LOCK, 3/8"

WASHER,PLAIN,M10 X M26 X 2

VF13501

ZD45407

ZD45000

VF14230

ǂǂǂ NUT,LOCK,M12

KEY, 6.35 X 25

ǂǂǂ BRUSH MOTOR,24VDC, .75HP

ǂǂǂ SCREW, M5 X 15

19

FANG20HD - BRUSH/PAD DRIVE ASSEMBLY

NO

REQ'D

1

1

3

3

3

1

1

1

1

3

3

1

4

4

1

1

10

1

1

5

4

4

1

1

2

2

6

1

1

1

1

1

1

4

4

4

4

4

1

4

2

1

20

DIA

NO

23

24

25

26

27

28

17

18

19

20

21

22

29

30

31

32

33

34

8

9

6

7

10

11

3

4

1

2

5

12

13

14

15

16

PART

NUMBER

VF14245

VF82036

VV13650

VF13532

VV13601

VF14230

VF13536

VF82075

VF83121

VF82148

VF82040

VF81134

VF82042

VF81124

VF81403A

VF82168

VF81780

VF81125

VF81126

VF13495

VF13533

VF81127

VF82033-24

VV13607

VF83120

VF13502

VF81128

VV20509

VF81118

VF13540

VF82037

VF82069

VF82074

VF82038

FANG20HD - SOLUTION CONTROL ASSEMBLY

DESCRIPTION

SCREW, M5 X 6

SHAFT

SCREW, M4 X 10

WASHER,PLAIN, M5

WASHER,LOCK, M5

SCREW, M5 X 15

WASHER,PLAIN, M9.8 X M16 X 1

NUT, 3/8"

CABLE,SOLENOID

CLAMP, 16mm

HOSE BARB,TEE

TUBING, 50mm

ELBOW

TUBING, 115mm

ELBOW,SOLUTION TANK

FILTER

TIE

TUBING, 200mm

TUBING, 80mm

SCREW, M6 X 16

WASHER,PLAIN, M6 X M16 X 2

TUBING, 65mm

SOLUTION VALVE SOLENOID,24VDC

WASHER,LOCK, M6

BRACKET,SOLENOID

NUT,LOCK, M6

TUBING, 320mm

SCREW,M5X10

CLAMP

WASHER,WAVE, M12

BRACKET,DRAIN HOSE & VALVE

LABEL,VALVE

BUSHING

KNOB,VALVE ADJUST

NO

REQ'D

1

2

1

2

1

2

1

4

2

1

4

1

1

1

2

1

1

1

2

1

2

2

14

1

1

4

2

1

4

1

2

2

2

1

21

22

DIA

NO

1

13

14

15

16

17

18

19

20

21

22

23

4

5

2

3

6

7

8

9

10

11

12

FANG20HD - BRUSH SKIRT ASSEMBLY

PART

NUMBER

VF82808

VF13495

VV13607

VF13533

VF83107

VF83108

VF82013

VF82055

VF13514A

VF14236

VA13400

VA13474

VF82810

VF82809

VF82815

VF82807R

VV20519

VF82807

VF83109

VV20291

VF82806

VF82806L

VF83142

DESCRIPTION

BUMPER(20HD)

SCREW,M6X16

WASHER,LOCK,M6

WASHER,PLAIN,M6

BRACKET,SKIRT MOUNT

PIN,SKIRT

WHEEL,3"

BUSHING

WASHER,PLAIN,M8XM16.5X1

SCREW,M8X40

WASHER,PLAIN,M5XM25X1.5

SCREW,M5X16

GRIP,BUMPER

CLAMP,BUMPER

BUMPER(20HD)

RIGHT SKIRT,ASSEMBLY

SCREW,M4X8

SKIRT,RIGHT

LATCH,HOOD

WASHER,LOCK,M4

SKIRT,LEFT

LEFT SKIRT,ASSEMBLY

BLOCK,SKIRT

NO

REQ'D

1

1

1

2

2

4

1

1

1

1

4

2

8

2

8

8

2

2

2

2

2

16

16

23

24

DIA

NO

1

2

3

4

5

6

29

30

31

32

33

34

35

22

23

24

25

26

27

28

13

14

15

16

17

7

8

9

10

11

12

18

19

20

21

43

44

45

46

47

36

37

38

39

40

41

42

48

49

50

51

52

53

PART

NUMBER

VF13491

VF14122

VF14121

VF13502

GT13032

VF81781

VF81781-X

VF81726A

VF81734

VF83149

VF82301

VF81713

VF82305

VF14078

VA50477

VF81718

VF82313

VF13495

VF81719

VF83137A

VF82811

VF81721

VF81727

VF81725

VF14200

VF81730

VF81709

VF81716

VF81710

VF81729

VF82316

VF81739-20T

VF82812

GV40239

VF83148

VF82303A

VF81703

VF82312

VF99012

VF82107BD

VF81711

VF81712

VF13514A

VF82106BD

VF14212

VF13511

VF44203

VF81707

VV13652

VF81714

VF82153

VF82160

VF81744B

VF81722

DESCRIPTION

SCREW, M4 X 12

WASHER,PLAIN, M10 X M20 X 2

SCREW, M10 X 65

NUT,LOCK, M6

WASHER,PLAIN, M6

DIODE, 400V

DIODE WITH ENDS

SOLENOID, 24V

BREAKER,CIRCUIT,35AMP

LABEL,CIRCUIT BREAKER

HOUSING,CONTROL

BUSHING

LABEL,SPEED CONTROL

SCREW,M3 X 10

WASHER,PLAIN, M3 X M10 X 1

LIGHTS,BATTERY CAPACITY

GASKET

SCREW, M6 X 16

SPACER

PANEL,SWITCH (24")

LABEL,SWITCH (FANG 20HD)

SWITCH,LIGHTED ROCKER

GAUGE,BRUSH PRESSURE

SWITCH,BRUSH LIFT

SCREW, M6 X 16

KNOB,SPEED CONTROL

PIN,HANDLE LOCK

SPRING

PIN,HANDLE ADJUSTMENT

POTIENTIOMETER, 4.7K

PLATE

SPEED CONTROL,BOARD

SERIAL TAG (FANG 20HD)

COVER

LABEL,CIRCUIT BREAKER

PANEL,CONTROL HOUSING

BATTERY CAPACITY CONTROL,BOARD

GASKET

BREAKER,CIRCUIT, 12 AMP

HANDLE,RIGHT

BOLT,SHOULDER, M8 X 15 X M6

SPRING

WASHER,PLAING, M8 X M16.5 X 1

HANDLE,LEFT

SCREW, M3X25

WASHER,TEETH, M3

SWITCH ASSY

BRACKET,SWITCH (24")

NUT,LOCK, M3

TUBE,HANDLE,ADJUSTMENT

SWITCH,KEY

LABEL,KEY SWITCH

STRAIN RELIEF,CORD

SWITCH,TOGGLE

25

FANG20HD - CONTROL HOUSING

NO

REQ'D

6

1

1

4

1

1

4

1

2

1

6

6

1

1

12

1

2

1

2

3

3

3

2

1

7

2

2

10

6

1

2

2

1

1

1

1

2

1

1

1

2

1

1

1

1

1

1

1

1

1

1

2

1

1

26

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

DIA

NO

1

15

16

17

18

19

9

10

11

12

13

14

4

5

2

3

6

7

8

20

PART

NUMBER

VF13501

VF82119

VF81218A

VF81209

VF14310

VF81208A

GT13022

VF81222

VF81219

VF13535

VV20203

VF82120

VF82120A

VF82062

VF82117

VF82118

VF82121

VF13502

VF83123

VF13521

VF13539

VF82908A

VF13538

VF83122

VF13637

VF14238

VF82016A

VF81243

VF82112

VF81203A

VF83150

VF83144

VF82047

VF83125

VF81210

VF14236

VF13514A

VF82055

VF82013

VF82116

VF82063

DESCRIPTION

ǂǂǂǂ NUT,LOCK, M12

ǂǂǂǂ WASHER,PLAIN, M12 X M26 X 2

ǂǂǂǂ MOUNT,PIVOT

ǂǂǂǂ SCREW, M12 X 130

ǂǂǂǂ SCREW, M12 X 30

ǂǂǂǂ BUSHING

ǂǂǂǂ CABLE,SQGE,LIFT (24")

ǂǂǂǂ BUSHING

ǂǂǂǂ HOSE

ǂǂǂǂ HOLDER,"U" HOSE

ǂǂǂǂ SPRING

ǂǂǂǂ SHAFT

ǂǂǂǂ BRACKET,SPRING

ǂǂǂǂ KNOB, M8

ǂǂǂǂ SCREW,M8 X 40

ǂǂǂǂ WASHER,PLAIN, M8 X M16.5 X 1

ǂǂǂǂ BUSHING

ǂǂǂǂ WHEEL, 3"

HOUSING,SQUEEGEE (FANG 20)

ǂǂǂǂ BLADEˈSQUEEGEEˈREAR˄PU˅

ǂǂǂǂ BLADE,SQUEEGEE,REAR˄NEOPRENE˅

ǂǂǂǂ LATCH,HOOD

ǂǂǂǂ HOOK,REAR SQUEEGEE BACKUP ADJUSTMENT

ǂǂǂǂ SCREW, M5 X 70

ǂǂǂǂ RIVET, M4 X 5

ǂǂǂǂ NUT,LOCK, M5

ǂǂǂǂ BOLT,SHOULDER, 5/16" X 1.25"

ǂǂǂǂ WHEEL, 2"

ǂǂǂǂ WASHER,PLAIN, M8 X M20 X 2

ǂǂǂǂ NUT,LOCK, 5/16"

ǂǂǂǂ BACKUP STRIP,SQUEEGEE,REAR

ǂǂǂǂ KIT,SQUEEGEE REAR BACKUP STRIP

ǂǂǂǂ BLADE,SQUEEGEE,FRONT,(PU)

ǂǂǂǂ BLADE,SQUEEGEE,FRONT,(NEOPRENE)

ǂǂǂǂ BACKUP STRIP,SQUEEGEE,FRONT

ǂǂǂǂ KNOB, M6

ǂǂǂǂ NUT,LOCK, M6

ǂǂǂǂ BRACKET,SQGE,MOUNT

ǂǂǂǂ NUT, M6

ǂǂǂǂ WASHER,PLAIN, M12 X M32 X 2

ǂǂǂǂ SQUEEGEE ASSY

27

FANG20HD - SQUEEGEE ASSEMBLY

NO

REQ'D

3

3

3

1

3

3

1

1

2

1

1

1

4

1

1

1

1

1

6

1

1

1

2

2

1

1

4

2

1

1

1

3

1

1

1

2

1

1

2

1

1

28

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Questions and Answers

How to connect the battery?
Connect the cables to battery posts in numerical order: RED to POSITIVE and BLACK to NEGATIVE.
How to fill the water tanks?
Pour water into the front or rear fill area; Front fill for use with hose or bucket, and rear fill for use with hose only.
How to operate the machine?
1. Set control housing at desired height, lower squeegee and brush assemblies, turn power on, and activate vacuum switch. 2. Turn on brush and solution switches, pull triggers to start scrubbing.
What to do when squeezing leaves streaks?
Raise squeegee, wipe blades with a damp cloth, and lower squeegee.
How to drain the solution tank?
Pull down the clear tube from hose barb, rinse tank with clean water.
How to Maintain the Scrubber?
Refer to the 'Preventative Maintenance' section in the manual for a detailed guide on maintaining the machine.

Related manuals

Download PDF

advertisement